Unknown OSS reteival error
===============================================================================
Broadcom Netxtreme Firmware Package
===============================================================================
Firmware Version: 212.0.5.4
This package updates the Broadcom Firmware Code to the levels shown under the
"Version" column for the products listed below :
ThinkSystem Adapters / LOMs ASIC
---------------------------------------- -----
ThinkSystem SR150/SR158 / SR250/SR258 / ST250/ST258 5720
Broadcom NetXtreme PCIe 1Gb 2-Port RJ45 Ethernet Adapter (7ZT7A00482) 5720
Broadcom NetXtreme PCIe 1Gb 4-Port RJ45 Ethernet Adapter (7ZT7A00484) 5719
System x Adapters / LOMs ASIC
---------------------------------------- -----
System x3650 M5 / x3550 M5 / x3500 M5 5719
NeXtScale nx360 M5 5717_C0
Broadcom NetXtreme I Dual Port GbE Adapter (90Y9370) 5720
Flex System EN2024 4-port 1Gb Ethernet Adapter (49Y7900) 5718
Broadcom NetXtreme I Quad Port GbE Adapter (90Y9352) 5719
===============================================================================
Change History
===============================================================================
Firmware Version: 212.0.5.4
---------------------------
Boot Code
ASIC Version
---- -------
5717 1.65
5717_C0 2.10
5718 1.65
5719 1.47
5720 1.39
ThinkSystem Adapters / LOMs
-----------------------------
PXE Code 20.6.1
UEFI Code 20.12.9
ISCSI Code 212.0.12
NCSI Code 1.4.26
MGMT_FW Code 1.12
System x Adapters / LOMs
-----------------------------
PXE Code 20.6.1
UEFI Code 17.4.9
ISCSI Code 212.0.12
NCSI Code 1.4.26
MGMT_FW Code 1.12
Problems Fixed:
- Rolled back legacy PXE Code to the level contained in package 20.6.4.3a
(20.6.1). The level contained in package 212.0.4.3 (20.6.50) uses much
more conventional memory, which can cause other devices like storage
adapters to run out of resources. These are functionally equivalent.
- Updated NCSI Code to:
- Fix an issue where 5719 ASIC ports 3 and 4 do not go into WOL mode
when AC power is first applied
- Updated ThinkSystem UEFI code to:
- Fix several configuration options which had no default value
- Add a 'Firmware Bundle' version to the Firmware Image Menu in F1 setup
- Updated the firmware update utility to:
- Fix a failure to update firmware under SLES 15
- Fix a failure where the update stops with a "file is too big" error
===============================================================================
===============================================================================
Firmware Version: 212.0.4.3
---------------------------
Boot Code
ASIC Version
---- -------
5717 1.65
5717_C0 2.10
5718 1.65
5719 1.47
5720 1.39
ThinkSystem Adapters / LOMs
-----------------------------
PXE Code 20.6.50
UEFI Code 20.12.4
ISCSI Code 212.0.12
NCSI Code 1.4.22
MGMT_FW Code 1.12
System x Adapters / LOMs
-----------------------------
PXE Code 20.6.50
UEFI Code 17.4.9
ISCSI Code 212.0.12
NCSI Code 1.4.22
MGMT_FW Code 1.12
Problems Fixed:
- Updated firmware update utility to:
- Support SLES15
- Disable check for Fcode allowing removal if needed.
- Enable logging for command line mode.
- Updated UEFI UNDI driver to:
- Fix the individual port enable/disable setting that is visible for
BCM5719 LOMs/NICS in F1 setup. Settings changes were not being saved
in ThinkSystem machines
- Fix a potential incompatibility with newer system UEFI levels, a hang
will occur while attempting to UEFI PXE boot. Newer levels of system
UEFI no longer enable busmaster enable bit in PCI configuration space
- Add the adapter port MAC address to the listing in F1 setup Network menu
Enhancements:
- Combined firmware package for both ThinkSystem and System x products
===============================================================================
===============================================================================
Firmware Version: 20.6.4.3a
---------------------------
Boot Code
ASIC Version
---- -------
5719 1.47
5720 1.39
ThinkSystem Adapters / LOMs
---------------------------
UEFI Code 20.6.13
PXE Code 20.6.1
ISCSI Code 20.6.2
Problems Fixed:
Enhancements:
- Initial release supporting only these ThinkSystem adapters:
Broadcom NetXtreme PCIe 1Gb 4-Port RJ45 Ethernet Adapter (7ZT7A00484)
Broadcom NetXtreme PCIe 1Gb 2-Port RJ45 Ethernet Adapter (7ZT7A00482)
===============================================================================
===============================================================================
Firmware Version: 17.4.4.8-c
----------------------------
Boot Code
ASIC Version
---- -------
5717 1.65
5717_C0 2.10
5718 1.65
5719 1.47
5720 1.39
System x Adapters / LOMs
------------------------
UEFI Code 17.4.9
PXE Code 17.2.1
ISCSI Code 18.0.0
IMFW Code 1.12
NCSI Code 1.04.01
Problems Fixed:
- Corrected an issue where the Permanent MAC Address reported via IMM may
be incorrect or duplicated
- Bogus "SMASH" entry may appear in F1 setup firmware menu after LOM
update.
Enhancements:
===============================================================================
===============================================================================
Firmware Version: 17.4.4.7a
---------------------------
Boot Code
ASIC Version
---- -------
5717 1.65
5717_C0 2.10
5718 1.65
5719 1.47
5720 1.39
System x Adapters / LOMs
------------------------
UEFI Code 17.4.8
PXE Code 17.2.1
ISCSI Code 18.0.0
IMFW Code 1.12
NCSI Code 1.04.01
Problems Fixed:
- Fixed issue with tx/rx flow control in shared nic mode where connection
to IMM is lost for a period of time after the server is powered off.
- Fixed issue with mac address filtering in shared nic mode where
connection to IMM is lost after a system reboot.
Enhancements:
- Added individual port enable/disable functionality in F1 Setup and
ASU/OneCLI for the following:
Adapters: NetXtreme I Quad Port GbE Adapter
Systems (LOMs): x3650 M5, x3550 M5, x3500 M5
===============================================================================
===============================================================================
Firmware Version: 17.4.4.2a
---------------------------
Boot Code
ASIC Version
---- -------
5717 1.65
5717_C0 2.10
5718 1.65
5719 1.43
5720 1.39
System x Adapters / LOMs
------------------------
UEFI Code 17.4.0
PXE Code 17.2.1
ISCSI Code 18.0.0
IMFW Code 1.12
NCSI Code 1.03.12
Problems Fixed:
- Updated the firmware update tool, a bug was found where it would not
attempt to update package version 15.x.x code.
Enhancements:
===============================================================================
===============================================================================
Firmware Version: 17.4.3.3a
---------------------------
Boot Code
ASIC Version
---- -------
5717 1.65
5717_C0 2.10
5718 1.65
5719 1.43
5720 1.39
System x Adapters / LOMs
------------------------
UEFI Code 17.4.0
PXE Code 17.2.1
ISCSI Code 18.0.0
IMFW Code 1.12
NCSI Code 1.03.12
Problems Fixed:
- ASU or XClarity is not able to restore default ISCSi settings
(such as 0.0.0.0) for adapters 90Y9352 and 90Y9370
- Invalid ISCSI parameters detected with ASU or XClarity on adapter
49Y7900.
- Flex x220 does not provide correct UUID to BOFM.
- Updated permanent MAC address retrieval logic when reporting the
value to AIM.
- Update permanent MAC address retrieval logic when reporting value to
additional AIM fields.
- Updated driver to modify attribute pattern strings for OEM devices.
- Removed extraneous HII page which was causing OEM parameter
extraction utility to show improper configuration.
- Update permanent MAC address retrieval logic when reporting value to
AIM.
Enhancements:
Broadcom NX-1 Ethernet Device Driver for SLES12
===============================================================================
Broadcom Netxtreme Device Driver for Linux
===============================================================================
Device Driver Version: 3.137x
Problems Fixed:
- tg3: Fix compilation error on kernel >= 4.13
Incremental Interoperability:
- None
Known Issues:
- None
===============================================================================