QLogic 16Gb Fibre Channel Adapter MultiFlash Update for System x for 00Y3337-00Y3344
QLogic 16 Gb Fibre Channel Adapter MultiFlash Update for System x
QLogic Corporation.
All rights reserved.
Version 4.74.11
04/13/2018
* Flash Image Version 4.74.11
HLD47411.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.43
uEFI version 6.24 signed
* FC Firmware - v8.07.12
* Pegtune - v5.110.23
* CRBnit - v5.14.15
* QLflash version 4.1.0.5
Change History
************************************************************************************
Version 4.74.10
08/08/2017
* Flash Image Version 4.74.10
HLD47410.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.43
uEFI version 6.24 signed
* FC Firmware - v8.05.63
* Pegtune - v5.110.23
* CRBnit - v5.14.15
* QLflash version 4.1.0.5
************************************************************************************
Version 4.74.09
07/11/2017
* Flash Image Version 4.74.09
HLD47409.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.43
uEFI version 6.24 signed
* FC Firmware - v8.05.61
* Pegtune - v5.110.23
* CRBnit - v5.14.15
* QLflash version 4.1.0.5
*************************************************************************************
Version 4.74.07
06/06/2017
* Flash Image Version 4.74.07
HLD47407.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.43
uEFI version 6.24 signed
* FC Firmware - v8.05.47
* Pegtune - v5.110.23
* CRBnit - v5.14.15
* QLflash version 4.1.0.5
BIOS Version
Version 3.43
* Fixed bug that caused FlexAddress to fail on Hilda adapters (ER139777).
Version 3.42
* Added delay before issuing zone command to get FA-BLUN (ER139690).
Version 3.41
* Added code to to allow direct connected LUN to be configured when FA_BLUN is enabled.
Version 3.40
* Removed Beta Banner
Version 3.40 Beta 3
* Added code to check for Embedded HBA flag in FBC to determine setting of Training Enable bit.
Version 3.40 Beta 2
* Changed code to check for selectable boot when FA_BLUN not found.
Version 3.40 Beta 1
* Added support for configuring FEC and BB_CR.
* Fixed issue in check_mem64 routine where pci address was not setup correctly.
UEFI Driver:
6.24
* Fixed formatting problems in the HII WWN Database menu. The
formatting problems only exist on older System X servers.
(ER140666)
* Built driver with x64 compiler. (ER140666)
* Microsoft signed driver.
*************************************************************************************
Version 4.74.03
01/17/2017
* Flash Image Version 4.74.03
HLD47403.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.39
uEFI version 6.23 (signed)
* FC Firmware - v8.03.00
* Pegtune - v5.110.23
* CRBnit - v5.14.15
* QLflash version 4.1.0.5
Version 3.39
* Fixed issue with 64bit addressing when BIOS enabled (ER138735).
Version 3.38
* Removed Beta Banner
Version 3.38 Beta 1
* Added code for load separate BIOS image for QLE27xx and QLE269x.(ER138517)
* Disabled CTRL-C option for BIOS setup utility (ER139677)
Version 3.37
* Added code to restore Virtual WWPN after cold boot for Baker based HBA's (ER138315).
Version 3.36
* Fixed bug created in BIOS 3.35 that caused BFS to fail (ER138533,ER138536).
Version 3.35
* Removed code that was preventing alternate FW from loading (ER138425).
Version 3.34
* Fixed issue with Show CLP Hilda FC pointer. (ER138211)
Version 3.33
* Fixed CTRL-Q utility datarate menu for Hilda HBA. (ER138168)
Version 3.32
* Removed Beta Banner
Version 3.32 Beta 2
* Fixed bug in setting pointer for secondary FW (ER137883).
Version 3.32 Beta 1
* Added support for QLipper
Version 3.31
* Removed Beta Banner
Version 3.31 Beta 2
* Added back Spin-up delay.(FOR DEBUG USE ONLY) (ER136488)
* Fixed issue with OCSD (ER136720)
Version 3.31 Beta 1
* Fixed bug in setting pointer for NVRAM access. This
* bug was created in version 3.30.
Version 3.30
* Removed Beta Banner
Version 3.30 Beta 1
* Added code to check for CTRl-Q disabled(ER135448).
* Added code to allow 4G data rate for 26xx(ER135693).
* Added check for which copy of FW to use(Baker only).
* Fixed issue with supporting 64bit Bar(ER136098).
*************************************************************************************
Version 4.74.02
12/01/2015
* Flash Image Version 4.74.02
HLD47402.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.29
uEFI version 6.23 (signed)
* FC Firmware - v8.03.00
* Pegtune - v5.110.23
* CRBnit - v5.14.15
* QLflash version 4.1.0.5
BIOS Version 3.29
* Fixed issue causing MD2 CLP to fail (ER135507).
Version 3.29 Beta 2
* Added code to fix CLP issue with 13G Dell system
Version 3.29 Beta 1
* Fixed bug in displaying Execution Throttle in CTRL-Q utility correctly for 4/8G HBA.
Version 3.28
* Removed Beta Banner
Version 3.28 Beta 2
* Added coded to load/start FW for OCBB/OCSD only when BIOS is disabled
Version 3.28 Beta 1
* Added support of Baker HBA
Version 3.27
* Added code to not configure any targets when FA Boot
* LUN enabled but FA BOOT LUN not found. ER133769.
* Added code to allow FA Boot LUN when FA WWPN enabled
* Added options in CTRL-Q utility to enable FA WWPN
* and FA BOOT LUN.
UEFI Driver: 6.23
* Updated HII to support System X and AMI based servers. (ER137721)
* Changed HII WWN Database behavior. The WWPN/LUN list is now
created when the driver starts. This allows driver to run on AMI
based servers. (ER137721)
* Updated a few HII strings. (ER137721)
* Fixed bug in UCM support. Callback flag now used to determine browser
mode or UCM mode. (ER137721)
* UCM WWN field is now a string. UCM did not properly support UINT64.
(ER137721)
*************************************************************************************
Version 4.72.12
09/22/2015
* Flash Image Version 4.72.12
HLD47212.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.29
uEFI version 6.22 signed
* FC Firmware - v7.05.04
* Pegtune - v5.110.23
* CRBnit - v5.14.15
* Removed Adapter Personality field from Agentless page. (ER136194)
* Microsoft signed driver.
*************************************************************************************
Version 4.70.07
03/26/2015
* Flash Image Version 4.70.07
HLD47007.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.29
uEFI version 6.21 Signed
* FC Firmware - v7.05.04
* Pegtune - v5.110.10
* CRBnit - v5.14.15
* Fixed issue causing MD2 CLP to fail (ER135507).
* Added code to fix CLP issue with 13G Dell system
* Fixed issue in displaying Execution Throttle in CTRL-Q utility correctly for 4/8G HBA.
* Added coded to load/start FW for OCBB/OCSD only when BIOS is disabled
* Added support of Baker HBA
* Added code to not configure any targets when FA Boot
* LUN enabled but FA BOOT LUN not found. ER133769.
* Added code to allow FA Boot LUN when FA WWPN enabled
* Added options in CTRL-Q utility to enable FA WWPN
and FA BOOT LUN.
* Fix minor cosmetic error in display of Fcode/EFI
versions for show port CLP.(ER133294)
* Added support FA BOOT LUN
* Added 8G support for show port clp
* Changed VLAN ID max value from 4095 to 4094.
* Removed spinup option from CTRL-Q.
* Changed CTRL-Q to allow max value for Login Retry,
* Port Down Retry, Link Down Count of 65535.ER(116099)
* Removed Helga support
* Added support for show port clp.
* Remove EV boot order option from OEM BIOS.
* Added CTRl_Q option to set VLAN_ID for FCoE HBA's(ER110593).
* Changed Banner to display 'FCoE' for Schultz (ER110784).
* Added additional time to login target when called
after EFI driver unloads. (ER110755,ER110855)
* Added code to handle boot LUN Greater Than 255 (ER109195).
* Added support for Helga.
* Added code to display message when 64 bit address is detected.
* Added support for Execution Throttle for P3P (ER106372)
* Added code to not display connection options for Hilda Trinity adapter.
* Checked for invalid LUN in CTRL-Q scan devices.
* Removed port number from HII formset title. This fixes a UCM parsing
issue. (ER134560).
*************************************************************************************
Version 3.20.09.a
12/11/2014
* Flash Image Version 3.20.09
HLD32009.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.24
uEFI version 6.20
* FC Firmware - v7.02.00
* QLflash version 4.1.0.5
These changes describe the changes, fixes, known issues, and
release details that apply to the FC-FCoE BIOS version 3.24.
Version 3.24
* Added code to display message when 64 bit address is detected.
* Added support for Execution Throttle for P3P (ER106372)
* Added code to not display connection options for Hilda Trinity adapter.
* Checked for invalid LUN in CTRL-Q scan devices.
* Fixed bug in CTRL_Q utility that could cause some cosmetic display issues.
* Added Hilda CLP _hss support.
* Configured ISP24xx if on slot 0.
* Added "QLogic" to PnP productid (ER104424)
* Checked for 4G flag in NVRAM for Hilda FC.(ER104714)
*************************************************************************************
Version 3.20.06
06/25/2014
HLD32006.BIN contains:
----------------------
* FC Bootcode (2600 Series only)
BIOS 3.0 version 3.24
uEFI version 6.17
* FC Firmware - v7.02.00
* Changed Banner to display 'FCoE' for Schultz (ER110790).
* Updated to get PN & Card SKU dynamically from I2C VPD for AIM (ER116141)
* Updated to get PN & Card SKU dynamically from I2C VPD for AIM (ER116141)
* Updated MTU size and AIM version references as per revised requirement. (ER113361)
* Updated AIM config strings as per revised requirements. (ER113361)
* Updated AIM support as per revised requirements (ER113361)
* Added fix for boot settings persistency issue in BOFM supported legacy BIOS (ER112641)
* Added support for Lenovo AIM [ER113361]
* Added fix to persist user changes made on static forms [ER112639]
* Added feature to dynamically list targets in HII [ER105725]
*************************************************************************************
Version 3.20.03
Date: 10/01/2013
BIOS 3.0 version 3.24
uEFI version 6.10
FC Firmware - v7.01.00
* Added additional time to login target when called
* after EFI driver unloads. (ER110755.ER110855)
* Added code to display message when 64 bit address detected.
* Added support for Execution Throttle for P3P (ER106372)
* Check for invalid LUN in CTRL-Q scan devices.
* Fixed bug in CTRL_Q utility that could cause some cosmetic display issues.
* Configure ISP24xx if on slot 0.
* Added "QLogic" to PnP productid (ER104424)
* Fixed bug with CTRL-Q Loopback Utility (ER100729).
* Added code to check/program Feature Config checksum.
* Fix bug that could cause buffer overrun in CTRL-Q with Report Lun command (ER100294).
* Added check for PCI address change when updating option card data structure.
* Changed code to use 32 bit pointer to allocate/deallocate EBDA memory.
* Added code to check/program Feature Config checksum.
* Fixed cosmetic issue in displaying data rate in CTRL-Q
* Fixed display issue with CTRL-Q Diskutility(ER98727)
* Fixed Lun select issue with CTRL-Q (ER98675).
* Fixed bug in displaying selectable boot lun (ER98226)
* Removed 4G data rate option for OEM adapter (ER98228)
* Limit leading '0's in CTRL-Q menu (ER98389).
* Set 'Aggressive Cooling' flag for OCSD.
* Enabled Personality Change option.
* Fixed issue with not restoring defaults on port 1 (ER 97619)
* Fixed issue with serdes data saved incorrectly. (ER 97654)
* Added code to limit Report Lun List size to 256 luns
* Added check for 0 lun count when selecting device (ER 97385)
* Disable Personality Change option in CTRL-Q.
* Fixed bug with WWNN handling for MCTP.(ER 96920)
* Added check for Set MD2 set to 0 (restore defaults) (ER96912)
* Added code to reset Port Config after Internal
loopback test(FCoE).
* Added support for 16 bit lun (er96090).
* Add support for Set MD2 CLP string.
* Added code to issue Load Flash FW (3) MB command as part ISP
start sequence. (ER 94035).
* Fixed code to prevent async event from causing BIOS
to hang when scanning for devices (er94371).
* Fix code to disable ALT+1 Hotkey (er92844) .
* Fixed CTRL-Q code mailbox timeout (er92957).
* Added warning message in Personality change screen.
* Updated BIOS to version 3.12 of non-hilda BIOS
* Removed check for Virtual Address on Cold Boot.
* Changed code to check for signature aaaaaaaah before
updating virtual mac address.
* Changed code to ignore soft boot signature aaaaaaaah
* Added code to save device number in OCSD.
* Added code to read cold boot register signature to
determine when BIOS should update/restore virtual
Mac address.
* Fixed bug where retry count was not always being updated.
* Added code to support ECHO lopback command.
* Added support NCSI Flex Address.
*************************************************************************************
Version 3.20.00
Date: 8/30/2013
BIOS 3.0 version 3.22
uEFI version 5.27
FC Firmware - v7.00.01
- Added code to display message when 64 bit address detected.
- Added support for Execution Throttle for P3P (ER106372)
- Added code to not display connection options for Hilda Trinity adapter.
- Check for invalid LUN in CTRL-Q scan devices.
- Fixed bug in CTRL_Q utility that could cause some cosmetic display issues.
- Add Hilda CLP _hss support.
- Configure ISP24xx if on slot 0.
- Added "QLogic" to PnP productid (ER104424)
- Check for 4G flag in NVRAM for Hilda FC.(ER104714)
- Fixed bug with CTRL-Q Loopback Utility (ER100729).
- Added code to check/program Feature Config checksum.
- Fix bug that could cause buffer overrun in CTRL-Q with Report Lun command (ER100294).
*************************************************************************************
Version 2.01.55
Date: 1/16/2013
BIOS 3.0 version 3.16
uEFI version 5.27
FC Firmware - v6.03.00
-Fix an issue where the first 4 bytes of the BootTargetWWN are set to FF
*************************************************************************************
Version: 2.01.26
Date: Initial Release
BIOS 3.0 version 3.16
uEFI version 5.26
FC Firmware - v6.03.00
Qlogic FC/FCoE Device Drivers for RHEL6
=======================================================
Change History for Qlogic Converged Network Adapter FC/FCoE Driver
=======================================================
Document Name: Change History
Document Status: Lenovo General Availability
Document Version: qla2xxx-8.07.00.56.e
Latest Package Version: qla2xxx-8.07.00.56.e
Latest Driver Version: 8.07.00.56.06.0-k1
Document Updated: 13-Apr-2018
Product: Qlogic FC/FCoE Linux Device Driver
=======================================================
Please visit www.qlogic.com/hba for full documentation, additional drivers,
and management applications.
Version qla2xxx-8.07.00.56.e
Changes to the RHEL6 LDPK:
- Correct the RPM naming convention in DUD.
Version 8.07.00.56.b
* Included SLES11.4 LDPK
* RHEL - Obsolete DUD RPM [ER0000000143124]
* SLES - Use matching RPM installation path. [ER0000000143124]
Version 8.07.00.56.a
* RHEL7, RHEL6, SLES12, SLES11, XS65, XS70, XS71, XS72:
* qla2xxx: relogin is being triggered too fast.
* Refresh all the SUPs packages with Pkgsdk4.12 and sLDPK1.19.
Version 8.07.00.51.b
* Refresh all the SUPs packages with Pkgsdk4.11 and sLDPK1.15.
Version 8.07.00.51.a
* RHEL7, RHEL6, SLES12, SLES12.2, SLES11.3, XS65, XS70:
* qla2xxx: Add LR distance support from nvram bit.
* qla2xxx: Add support for fabric priority per target.
* qla2xxx: Add timeout ability to wait_for_sess_deletion().
* qla2xxx: Fix ql_dump_buffer (avoid emitting on multiple lines).
* qla2xxx: Move logging default mask to execute once only.
* qla2xxx: Print correct mailbox registers in failed summary.
* qla2xxx: Allow SNS fabric login to be retried.
* qla2xxx: Correction to vha->vref_count timeout.
* qla2xxx: Process AEN 0x8200 for CNA cards only.
* qla2xxx: Test elreq.options for CNA only.
* qla2xxx: Use sp->free instead of hard coded call.
* qla2xxx: Prevent sp->free null pointer dereference.
* qla2xxx: Free sp after marking not busy.
* qla2xxx: Increase the login retry count to 30.
* qla2xxx: Properly calculate fwdump buffer size.
Version 8.07.00.42.o
* Refresh all the SUPs packages with sLDPKv1.10.
Version 8.07.00.42.n
* Refresh all the SUPs packages with PKGSDK4.08 and sLDPKv1.9.
Version 8.07.00.42.k
* [ER140565]-Boot from SAN fails after installing z stream kernel
rpm on RHEL 7.2 DUD.
* [ER140617]-Error when uninstalling RPM following instructions in readme.
(qlgc-lnvgy_dd_fc_qla2xxx-8.07.00.42.j_rhel7_x86-64 version issue)
Version 8.07.00.42.j
* Reprocessed with new kernels for SLES12SP2 and RHEL 7.3.
* Updates to readme(from Lenovo)
Scope : All Adapters
Version 8.07.00.42.i
* [ER140375] � SUPs Fail to install on SLES12SP2 and RHEL 7.3.
* Reprocessed the package with PKGSDK4.04
Scope : All Adapters
Version 8.07.00.42.h
Fixes and Ehancements:
* New PKGSDK4.02 is used to prepare the packages.
* qla2xxx: Remove all DIX-0 references.
Version 8.07.00.35.e
Fixes and Ehancements:
* New PKGSDK3.27 is used to prepare the packages.
* Support for RHEL6.8
* RPM singing enforcement
Version 8.07.00.35.b
Fixes and Ehancements:
SLES11:
* qla2xxx: version missing in tcm_qla2xxx module.
* sups: replace "_k" in xml file with "-k".
Version 8.07.00.35
Fixes and Ehancements:
Software/Driver
RHEL7, RHEL6, SLES11, SLES12, UEK, UEK2, XS65, XS6:
* qla2xxx: Shutdown board on thermal shutdown aen.
* qla2xxx: Correct RDP optical element array index.
* qla2xxx: Log only failure case message for abort command.
* qla2xxx: Add ram area DDR for fwdump template entry T262.
* qla2xxx: Correction to RDP extensions transgression flags.
* qla2xxx: Remove sysfs node fw_dump_template.
* qla2xxx: Argument to le32_to_cpus() should be a pointer.
* qla2xxx: Fix mbx_reg pointer iterator in 25xx fwdump routine.
* extras: Inline log.sed into log.sh
********************************************************************************
Version 8.07.00.3
Fixes and Ehancements:
Software/Driver
RHEL7, RHEL6, SLES11, SLES12, UEK, UEK2, XS65, XS6:
* qla2xxx: Add support to disable laser for ISP27XX.
* qla2xxx: Add RDP extensions.
* qla2xxx: Set relogin flag when we fail to queue login requests.
* qla2xxx: Fix default value descriptions for module parameters.
* qla2xxx: Enable T10-DIF for ISP27XX.
* qla2xxx: Use valid BBCR offset and datatype.
* Revert "qla2xxx: Set echo test mailbox command option bit15 correctly."
Version 8.07.00.27
Fixes and Ehancements:
Software/Driver
* qla2xxx: Avoid asynchronous abort requests.
* qla2xxx: Avoid crossing initiator/target modes during AEN handling.
* qla2xxx: Fix invalid offset reference of inquiry response data.
Version 8.06.00.10
Fixes and Ehancements:
Software/Driver
* Remove entry in outstanding_cmds array if we fail to abort a request.
* Clear RISC INT reg only for an event and not always while polling.
* Fix undefined behavior in call to snprintf().
* Added T10 DiF/DiX support for ISP83xx.
* ISP83xx CNA support
* IDC support for three protocols.
* Loopback support.
* Beacon support.
* Added support for bidirectional commands
* Added support for MCTP dump
* ISP83xx(16G FC) support for Xenserver 6.0 and Oracle UEK.
* SRB Consolidation.
* RSCN handling changes.
* Increase in support of maximum fibre devices.
* Enhancements to support ISP83xx (Limited support).
* Driver features supported
* 10GB link support only
* Port device discovery
* LUN discovery
* I/O
* Perturbations
* SG resets of host and SCSI devices.
* Driver features not supported
* Beacon support
* Loopback
* T10 DIX/DIF
* SFP read/write
* QCC GUI Support
* QCC CLI Support
* NPIV
* Multi-Queue
* Boot from SAN
* FC-Tape
* SLES10.3 driver:
* Fix not to MPI reset on ISP83xx is not included.
* Implemeted beacon on/off for ISP82xx.
* Add support for ISP82xx to capture dump (minidump) on failure.
* Provide method for updating I2C attached VPD.
* Resync with latest ISP24xx/25xx firmware (5.08.00).
Industry Standards Compliance
-----------------------------
* N/A
3. Bug Fixes
The following fix has been made to the Fibre Channel and FCoE
Adapter Inbox Driver Update for Linux Kernel 2.6.x and 3.x:
* 8.04.00.12.xx.y-k
* Update the copyright information.
* Display the lock owner on lock acquire failure.
* Move loopback mode reset after chip reset check.
* Extra loopback error handling for ISP83xx.
* Do link initialization on get loop id failure.
* Do MPI reset only for 81xx.
V2632 (RHEL 6.x, SLES 11.x, Citrix 6.0, UEK):
* Revert "qla2xxx: Optimize existing port name server query matching."
* Revert "qla2xxx: Avoid losing any fc ports when loop id's are exhausted."
* Don't free pool that wasn't allocated.
* Unload hangs after issuing BSG commands to vport.
Citrix 6.0:
* Create initrd as a part of installation and removal of the driver rpm.
* RPM install should install driver under extra instead of driver directory.
RHEL 5.x, SLES 10.x:
* MBA_IDC_NOTIFY case should fallthru.
* Add fw_dump_size sysfs attribute file.
* Add test for validity of virtual host in netlink interface.
SLES 10.x:
* Add 8031/2031 cases to request firmware.
* 8.04.00.11.xx.y-k
* Move marking fcport online ahead of setting iiDMA speed.
* Add 16Gb/s case to get port speed capability.
* Get VPD information from common location for CNA.
* Dont clear drv active on iospace config failure.
* Display that driver is operating in legacy interrupt mode.
* Add "16" speed to link speeds array in qla2x00_iidma_fcport() function
* Correct race in loop_state assignment during reset handling.
* Reject loopback request if one is already in progress.
* Update the FTP site references in the driver sources.
V2632 (RHEL 6.x, SLES 11.x Citrix 6.0 and UEK):
* Obtain loopback iteration count from bsg request.
* Parameterize the link speed string conversion function.
* Update ql2xextended_error_logging parameter description with new options.
* Fix typo in qla2xxx driver.
* Free rsp_data even on error in qla2x00_process_loopback().
* Avoid null pointer dereference in shutdown routine.
RHEL 5.x:
* Remove fabric_logout() calls from qla2x00_dev_loss_tmo_callbk() function.
SLES10.x:
* Clear local references of rport on device loss timeout notification from FC transport.
* 8.04.00.10.xx.y-k
* Honor status value of 2 for report-id acquisition.
* Ignore driver ack bit if corresponding presence bit is not set.
* Add Gen3 PCIe speed 8GT/s to the log message.
* Acquire risc semaphore before resetting ISP.
V2632 (RHEL 6.x, SLES 11.x Citrix 6.0 and UEK):
* Ramp down queue depth for attached SCSI devices when driver resources are low.
* Determine the number of outstanding commands based on available resources.
* Fix for kernel crash when external loopback diagnostic is run through BSG interface.
* Fix coccinelle warnings in qla2x00_relogin.
* Test and clear FCPORT_UPDATE_NEEDED atomically.
* Use correct Request-Q-Out register during bidirectional request processing
* Fix typo in qla83xx_fw_dump function.
* Move noisy Start scsi failed messages to verbose logging level.
* Fix for warnings reported by sparse.
RHEL 5.x:
* Inclusion of 4G/8G firmware version 5.08.00.
* Log message when qla2xenablemsix module parameter is set to 2( MSI mode) and adpater does not support MSI mode.
* Revert "qla2xxx: Use GFF_ID to check FCP-SCSI FC4 type before logging into Nx_Ports"
* Revert "qla2xxx: No fcport FC-4 type assignment in GA_NXT response."
Citrix 6.x:
* RPM build should hide the directory naming convention from user.
* 8.04.00.09.xx.y-k
* No fcport FC-4 type assignment in GA_NXT response.
* Fix checkpatch error in qla2xxx_mctp_dump.
* Change in setting UNLOADING flag and FC vports logout sequence while unloading qla2xxx driver.
* Clear unsupported 'states' during Get-FW-State queries.
V2632 (RHEL 6.x, SLES 11.x Citrix 6.0 and UEK):
* Pass correct parameters while creating an initrd.
* Remove spurious taking of ha->vport_slock spinlock.
UEK:
* Add macro for kernel extended version.
RHEL 5.x:
* Use GFF_ID to check FCP-SCSI FC4 type before logging into Nx_Ports.
* Pass correct parameters while creating an initrd.
********************************************************************************
8.04.00.08
Initial release of Qlogic 10Gb FC Driver for RHEL5