Lenovo YUM Repository
Release and Change History








Bundle Release Information:
Targeted Server Family (Machine Type): ThinkSystem SR655 (7Y00, 7Z01)
Targeted Operating System: SLES12SP4
YUM Repository Build Date: 2021_12_29

YUM Repository Release Version: 22A

Device:
ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter

Device Product Guide

Part Number: 4Y37A09722
Feature Code: AUNH
PCIe Sub Vendor ID: 0x1D49
PCIe Sub Device ID: 0x0608


Release History:

Release Change History Documents

ThinkSystem RAID 730-8i PCIe 12Gb Adapter Update BIOS and Firmware (For Linux)



BIOS and Firmware Update for ThinkSystem RAID 730-8i XGB Cache PCIe 12Gb Adapter

Supported Adapters:
				ThinkSystem RAID 730-8i 1GB Cache PCIe 12Gb Adapter  (7Y37A01083)
	            ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter  (4Y37A09722)

NOTE TO SERVICE - Reference RETAIN #N/A

Version 24.21.0-0151 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0151
BIOS: 6.36.00.3
UEFI Driver:0x06180205
HII:03.25.05.14
MR NVDATA:3.1705.00-0024
iMR NVDATA - 3.1705.01-0018
MR Firmware - 4.680.00-8561
iMR Firmware - 4.680.01-8560

Defects:
-FW 6.14 - Fatal firmware error due to hitting DATA TLB exception.(DCSG00922969)
-Drive state "Prepare for removal" operation showing error message "Failed!" while changing in Ctrl-R.(DCSG00436264)
-MR 6.14 NVDATA - Change OEM specific iMR Controller's Product Name.(DCSG00427750)
-OEM specific iMR - StorCLI /c0 show all status is failed with "Eror code 2 command invalid".(DCSG00257202)

EnhancementRequest:
-iMR NVDATA 6.14 - Porting OEM specific NVDATA from 6.10 to 6.14 stream.(DCSG00253618)
-MR 6.14 Invader NVDATA - Enable "LARGEIOSUPPORT" for OEM specific controller.(DCSG00318093)

Version 24.21.0-0148 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0148
BIOS: 6.36.00.3
UEFI Driver:0x06180205
HII: 03.25.05.14
MR NVDATA:3.1705.00-0024
iMR NVDATA - 3.1705.01-0018
MR Firmware - 4.680.00-8555
iMR Firmware - 4.680.01-8554
MR 6.14

Defects:
-MR6.14:Observed the FW crash @ C0:Assertion failure in ../../raid/cache.c at line 3642: c_ptr->stripe == stripe while FW update with power cycle.(DCSG00554803)
-Enclosure power cable pulling event is not reported.(DCSG00423361)
-MR_6.14: observed the config loss while creating VD using spindown drives and OCR.(DCSG00398711)
-Assertion failure in ../../raid/writeJournal.c after FW upgrade with cache header change.(DCSG00501563)

EnhancementRequests:
-MR FW 6.14 - OEM migration from 6.10 to 6.14 - MR FW changes Phase-1 - Part3.(DCSG00359298)
-MR FW 6.14 - Integration of Intruder Phase 14 MR PL Version - 14.00.16.00.(DCSG00380515)
-6.14 MR FW - Defect fixes port from 6.10 to 6.14 - Part B.(DCSG00383220)
-MR FW 6.14 - Integrate MR Invader PL 14.00.19.00 Firmware.(DCSG00425937)
-MR FW 6.14 - Integrate MR Intruder PL 14.00.17.00 Firmware.(DCSG00425943)
-Control the PD Degraded Media operations feature (and setting Read retry count in HDDs recovery mode page to 1) by NVDATA settings instead of always enabling it in JBOD personality..(DCSG00380527)
-6.14 MR FW - Defect fixes port from 6.10 to 6.14 - Part A.(DCSG00359361)
-Specific OEM Migration from 6.10 to 6.14 - 6.14 MR FW Changes PHASE-2 Part A.(DCSG00297480)


Version 24.21.0-0143 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0143
BIOS: 6.36.00.3
UEFI Driver:0x06180204
HII: 03.25.05.14
MR NVDATA: 3.1705.00-0024
iMR NVDATA - 3.1705.01-0017
MR Firmware - 4.680.00-8545
iMR Firmware - 4.680.01-8544

Defects:
- Controller cache discarded critical boot message posted during reboot following an OCR when snapdump is generated on a controller without a good supercap..(DCSG00405903)
- Controller cache discarded critical boot message posted during reboot when snapdump is generated on a controller without a good supercap..(DCSG00405906)
- Controller cache discarded critical boot message posted during reboot following an OCR when snapdump is generated on a controller without a good supercap..(DCSG00405903)
- Controller cache discarded critical boot message posted during reboot when snapdump is generated on a controller without a good supercap.(DCSG00405906)
- OEM specific iMR - StorCLI /c0 show all status is failed with "Eror code 2 command invalid".(DCSG00257202)
- iMR NVDATA 6.14 - Porting OEM specific NVDATA from 6.10 to 6.14 stream.(DCSG00253618)
- MR 6.14 Invader NVDATA - Enable "LARGEIOSUPPORT" for OEM specific controller.(DCSG00318093)
- OEM specific iMR - StorCLI /c0 show all status is failed with "Eror code 2 command invalid".(DCSG00257202)
- iMR NVDATA 6.14 - Porting OEM specific NVDATA from 6.10 to 6.14 stream.(DCSG00253618)
- MR 6.14 Invader NVDATA - Enable "LARGEIOSUPPORT" for OEM specific controller.(DCSG00318093)


Version 24.21.0-0140 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0140
BIOS: 6.36.00.3
UEFI Driver:0x06180204
HII: 03.25.05.14
MR NVDATA: 3.1705.00-0024
iMR NVDATA - 3.1705.01-0017
MR Firmware - 4.680.00-8539
iMR Firmware - 4.680.01-8538
MR 6.14

defects:
-MR6.14: Failed to create EPD on JBOD mode when "enableJBOD=1 " was set on controller in RAID Mode.(DCSG00346843)
-MR FW 6.14: Sanitize - CrytoErase Sanitize type is failing on FDE capable drives (SED drive).(DCSG00134675)
-[9361-8i MR6.14] storcli return with error when set patrolread mode.(DCSG00072635)
-MR FW 6.14 : Creating VD for Direct Connect fails.(DCSG00068474)
-Dev defect: When L3 is disabled as HW WA, update L3 Interrupt Service Routine to detect unexpected interrupts.(DCSG00146729)
-MR 6.14 Sanitize support - Retain the FW behavior for Crypto Erase (ISE) issued using older apps style for backward compatibility.(DCSG00129646)
-Invader JBOD personality mode with SED drive and security enabled, partition and data disappears after reboot..(DCSG00324212)
-Unconfigured Good Drive moves to SHIELD state during enclosure power cycle test.(DCSG00276638)
-MR 6.14:While clearing the configuration sanitize running drives state has been changed from SANITIZE_IN_PROGRESS(4) to UNCONFIGURED_GOOD(0).(DCSG00146728)
-SEP discovery issue after reset / enclosure reset.(DCSG00074489)
-MR 6.14 Invader FW: Dev Defect - Possible loss of snap dump data during abrupt power loss while manipulating TTY history BBU settings.(DCSG00102246)
-MR 6.14 - Sanitize: FW sanitize progress events shouldn't have total elapsed time in operations.(DCSG00129198)
-6.14 Dev Defect - Fix slot status update based on PD state for specific OEM.(DCSG00317899)
-JBOD drive is converted to Configured Drive after OCR / Reboot.(DCSG00293760 (Port Of Defect DCSG00320632))
-Potential DC when recon is started and if there is already a VD of target ID 239(in case of 240 VD environment) or 63 (in case of 64 VD environment).(DCSG00134460 (Port Of Defect DCSG00235950))

EnhancementRequests:
-MR_FW_SAS3_6.14 - Integration of Invader Phase 14 MR PL FW Version - 14.00.18.00.(DCSG00370777)
-MR_FW_SAS3_6.14 - Integration of Invader Phase 14 MR PL FW Version - 14.00.16.00.(DCSG00254828)
-Ported one defect fix from 6.10 OEM specific stream to 6.14.(DCSG00323555)
-MR FW 6.14 - Porting OEM specific features from 6.10 to 6.14.(DCSG00253615)
-Unblock pass-through SCSI Sanitize command on SYSTEM PDs in RAID personality.(DCSG00317881)
-MR FW 6.x - Integration of Intruder Phase 14 MR PL Version - 14.00.13.00.(DCSG00136411)
-MR FW 6.14 - Integration of Intruder Phase 14 MR PL Version - 14.00.14.00.(DCSG00146868)
-MR FW 6.14 - Integration of Invader Phase 14 MR PL FW Version - 14.00.15.00.(DCSG00230289)
-L3 cache bypassed on Intruder based controllers.(DCSG00138048)
-MR FW 6.x - Integration of Invader Phase 14 MR PL Version - 14.00.13.00.(DCSG00136418)
-MR_FW_SAS3_6.14 - Integration of Invader Phase 14 MR PL FW Version - 14.00.17.00.(DCSG00323604)
-MR FW 6.x - Integration of Intruder Phase 14 MR PL Version - 14.00.12.00.(DCSG00103433)
-MR FW 6.14 - Integration of Invader Phase 14 MR PL Version - 14.00.14.00.(DCSG00146867)
-MR FW 6.x - Sanitize command support for SAS/SATA UG drives.(DCSG00077493)
-MR FW 6.14 - Integration of Intruder Phase 14 MR PL Version - 14.00.15.00.(DCSG00297457)
-MR FW 6.10 to 6.14 Migration Phase 1 - Part 2 - OEM specific features ported from 6.10 to 6.14 FW.(DCSG00255556)
-MR FW 6.x - Integration of Invader Phase 14 MR PL Version - 14.00.12.00.(DCSG00103429)


Version 24.21.0-0126 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0126
BIOS: 6.36.00.3
UEFI Driver:0x06180203
HII: 03.25.05.12
MR NVDATA: 3.1705.00-0021
iMR NVDATA - 3.1705.01-0013
MR Firmware - 4.680.00-8519
iMR Firmware - 4.680.01-8518
MR 6.14

defects:
Incomplete onfi configuration leads to FW HALT.(DCSG00051973)
SAS9341-8i board encounters 'Previous configuration completely missing at boot' error.(DCSG00067176)
MR 6.14 - MR FW resets the controller on/off property "allowBootWithPinnedCache" on every boot.(DCSG00069702)
Unable to import foreign config.(DCSG00041146 (Port Of Defect DCSG00025975)
Repeated TASK ABORTS and access to the data store lost.(DCSG00066009 (Port Of Defect DCSG00063321))
Cache offload is not getting completed during dummy descriptor configuration.(DCSG00048845)

Version 24.21.0-0124 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0124
BIOS: 6.36.00.3
UEFI Driver:0x06180203
HII: 03.25.05.12
MR NVDATA: 3.1705.00-0020
iMR NVDATA - 3.1705.01-0012
MR Firmware - 4.680.00-8515
iMR Firmware - 4.680.01-8514
MR_6.14

Defects (21)
  - During config force clear, invader MR FW hits assertion.(SCGCQ02154000)
  - 614.1_FW: Controller is not detecting in OS on a latest FW pkg 24.21.0-0108 when expander is connected to controller and configured for zoning.(SCGCQ02157970)
  - Firmware crashes while running IO's with flushwriteverify=on.(SCGCQ02174924)
  - Triggering Back to Back OnDemand Snapdump leads to generation of Duplicate Snapdump entries/files.(SCGCQ02187566)
  - Firmware initialization failed. Fault code = 0x22 !!! observed during FW Downgrade/upgrade.(SCGCQ02191364)
  - Patrol Read never progresses when Patrol read rate is set to less than 10%.(SCGCQ02197015)
  - AVAGO_B doesn't reflect in boot VDs vendor ID if boot device is changed from JBOD to LD.(SCGCQ02162341)
  - Cache Data Loss with ONFI double dip with bad SuperCAP.(SCGCQ02167986)
  - Snapdump 6.14 - Check on the ONFI Data structures being dumped properly.(SCGCQ02182249)
  - Snapdump is not generating for Kill Adapter (when there is no IO TimeOut).(SCGCQ02189995)
  - Snapdump files are not getting erased after ~5 System Reboots, when Snapdump save count is set to 4.(SCGCQ02195001)
  - Assertion failure observed, when user has initiated KA and SD is disabled.(SCGCQ02198254)
  - MR FW marks Zoned Out PHYs as bad PHYs.(SCGCQ02152834)
  - During the push pull test, with different delay for each drive , leads to assert.(SCGCQ02157827)
  - As timeout happens for a command ,driver sends KA.(SCGCQ02169505)
  - Snapdump 6.14 - Clean up the snapdump table and its associated functions.(SCGCQ02181209)
  - MR_6.14: "SnapDumpDbg faultingModule 0 moduleBmp 1f6f faultFunc 0 FaultCode 1" Observed while trying to get Snapdump.(SCGCQ02198608)
  - DEV DEFECT: iMR 6.14 - Disable unused debug code compilations for Skinny.(SCGCQ02183672)
  - FW should clear the snapdump during personality change.(SCGCQ02194577)
  - MR 6.14 - Multi-bit ECC errors seen on Invader board in JBOD personality mode.(SCGCQ02207367)
  - Dev Defect: Snapdump 6.14: Addressing the review comments for ERs.(SCGCQ02174425)
  - Aero PA0.8: (Vision) Snapdump Fails to generate after Assertion failure in fw\cpu\arm\exceptions.c during Cable Push.(SCGCQ01940055 port of SCGCQ01918865)
  - Controller Hang after multiple iterations of S4 Sleeper Stress Test.(SCGCQ02099935 port of SCGCQ02059508)
  - MR7.10-9480-8i8e: DC during Single Dip COL Using Wingman Automation.(SCGCQ02140667 port of SCGCQ02077953)
  - [RHEL 8.1] system will hang with SME enable.(SCGCQ02192339 port of SCGCQ02184712)
  - Snapdump capture fails when COL restore occurs with ECC errors.(SCGCQ02197538 port of SCGCQ02041663)
  - Data Abort Exception on abrupt powerloss/reset when flushing events from NVRAM hold buffer to flash.(SCGCQ02113872 port of SCGCQ01973389)
  - EKMS 10.3: Reboot loop results in OS getting corrupted i,e 0xC000000E (Required Device is Inaccessible).(SCGCQ02140049 port of SCGCQ02080146)
  - Recon operation can lead to silent data corruption in certain scenarios.(SCGCQ02195549 port of SCGCQ02191510)
  - sense data returned from out-of-band storlibtest is wrong.(SCGCQ02112236 port of SCGCQ02050648)
  - Aero A0 UTP - Atlas Config NVMe3 TM + Cable pull/push results in CORE0 fault and OCR(SCGCQ02140684 port of SCGCQ02041132)
  - Security Subsystem Errors.(SCGCQ02157832 port of SCGCQ02139169)
  - DEV DEFECT: iMR 6.14 - Disable unused debug code compilations for Skinny.(SCGCQ02187494 port of SCGCQ02183672)
  - Aero UTP: On-demand snapdump lost when created before learn cycle on new SCAP.(SCGCQ02197294 port of SCGCQ02059851)
  - Aero PA4: getting on-demand snapdump right after FW flashing causes a FW exception.(SCGCQ02140030 port of SCGCQ02125329)
  - Fix to clear stale RLM failure state that fails subsequent RLMs.(SCGCQ02188879 port of SCGCQ02174426)
  - Snapdumps may include empty files if one of the file streams exceeds the allocated buffer.(SCGCQ02197295 port of SCGCQ02138164)
  - foreign import failed when sequence number mismatch.(SCGCQ01940056 port of SCGCQ01912560)
  - DEV DEFECT: iMR 6.14 - Disable unused debug code compilations for Skinny.(SCGCQ02190332 port of SCGCQ02183672)
 
EnhancementRequests (20)
  - Removed VDM driver workaround.(SCGCQ02144055)
  - Support LED functionality on disjoint SGPIO back-planes that report non-contiguous slot numbers.(SCGCQ02144062)
  - Snapdump base framework for Invader 6.14.(SCGCQ02150008)
  - Snapdump-6.14: Zmodem infrastructure support.(SCGCQ02151362)
  - Snapdump offload and restore across the abrupt reboots.(SCGCQ02165912)
  - Snapdump 6.14 Raid module: Generate snapdump when pinned cache is generated.(SCGCQ02172218)
  - Support Zone In and Zone Out functionality for MR 6.x Channel.(SCGCQ02129396)
  - Snapdump 6.14: Snapdump need to be retained after the OCR.(SCGCQ02164133)
  - Snapdump 6.14: Raid support-DDF module integration.(SCGCQ02174431)
  - TTY module integration to Snapdump.(SCGCQ02175357)
  - Generate Snapdump upon observing Data abort exceptions.(SCGCQ02180497)
  - 6.14 SnapDump: Controller property support for enabling snapDump.(SCGCQ02154867)
  - 6.14 SnapDump:Print re-routing frame work.(SCGCQ02154870)
  - Generate Snapdump on observing assertions and PL faults.(SCGCQ02165909)
  - DM module integration to Snapdump.(SCGCQ02172283)
  - Snapdump 6.14: Raid support-ONFI module integration.(SCGCQ02175257)
  - PL module integration to Snapdump.(SCGCQ02179473)
  - Snapdump 6.14: Early notification handling from driver for generation of snapdump.(SCGCQ02181283)
  - Snapdump 6.14 - Support of IOP related dump.(SCGCQ02182263)
  - SnapDump 6.14 :Integration of DDR framework to support snapdump.(SCGCQ02150010)
  

Version 24.21.0-0112-1 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0112-1
BIOS: 6.36.00.3
UEFI Driver: 0x06180203
HII:  03.25.05.12
MR NVDATA: 3.1705.00-0020
iMR NVDATA - 3.1705.01-0012
MR Firmware - 4.680.00-8489
iMR Firmware - 4.680.01-8488
MR 6.14

Defects (15)
 - LD Inquiry still show as AVAGO_B for VD even when JBOD drive is set as boot PD.(SCGCQ02052706)
 - Fatal FW error observed on connecting enclosure in a multipath or cascading another enclosure when slot based device ID feature is enabled.(SCGCQ02141291)
 - Fix API changes done for NVMe readiness(SCGCQ02142981)
 - Add NVMe width comments to mr.h(SCGCQ02146846)
 - During SpinUpRecoveySM 2/4/1C sense data is not handled(SCGCQ02149370)
 - Non boot VD gets vendor identification as "AVAGO_B" for a specific OEM(SCGCQ02160670)
 - Boot VD Inquiry String is not retained, after foreign importing the Boot VD configuration(SCGCQ02057908)
 - montask observed inline 1704 in ../../raid/bootMsg.c during enclosure cable pull/push.(SCGCQ02136344)
 - Flaky link drive connection causing a fatal error.(SCGCQ02141740)
 - SED drive moved to fail state during device missing delay (DMD)(SCGCQ02144016)
 - IOUNITPAGE 11 parameters are not updated in the next boot.(SCGCQ02154597)
 - TUR timeout increased from 64 sec to 120sec.(SCGCQ02118063)
 - When slot based device ID feature is enabled, Drive Slot id and device ids are not matching after hot plug of direct attached drives(SCGCQ02144003)
 - 6.14_FW : Fatal FW error observed on iMR controller after flashing latest FW pkg 24.21.0-0111 and rebooting the system.(SCGCQ02171024)
 -(SCGCQ02102580)
 - Initialize cache after diagnostics testing(SCGCQ02157830 port of SCGCQ02134286)
 - CSCuv03959 DPMR6 - System hung after abort running CC continuously overnight.(SCGCQ02169538 port of SCGCQ00883695)
 - IO Error observed on few VD's, after setting the boot drive in NVMe Mix Mode Configuration(SCGCQ02099404 port of SCGCQ02058292)
 - Kill Adapter if PD FW download is run in continous loop(SCGCQ02139082 port of SCGCQ02059825)
	
EnhancementRequests (32)
 - Add New Generic OOB API To Read ROC Temp, Drive Temp, Drive Type, Drive Protocol and status through OOB BMC(SCGCQ01940661)
 - Add a new log event used whenever the snap dump properties are modified.(SCGCQ01963328)
 - Add a bit for atomic descriptor capable(SCGCQ01965047)
 - Add CTRL_SB_SOFT_SECURE_MODE event to indicate soft secure mode(SCGCQ01965721)
 - Introduced new controller bit(SCGCQ01985474)
 - Customer needs to generate and extract the On-demand based debug data both for MR and iMR.(SCGCQ02000566)
 - Driver parameter bit for support of tool box cmd(SCGCQ02002119)
 - Add new MFI Fault sub code for Secure Boot Preboot Auth failure(SCGCQ02006657)
 - Reword event log messages as it creates unnecessary panic.(SCGCQ02013675)
 - Modification in MR_SNAPDUMP_TRIGGER_TYPE enum value(SCGCQ02030653)
 - Additional details about spare(SCGCQ02033538)
 - API change to support NVMe Passthrough over OOB(SCGCQ02035295)
 - API change to support new DCMD for consolidated device list(SCGCQ02037158)
 - API changes for NVMe speed and width changes(SCGCQ02053667)
 - API changes for linkconfig interface(SCGCQ02053671)
 - Increase in MR_PD_INFO.name length to 32 characters(SCGCQ02079068)
 - MR Windows IOCTL Error codes to Application added to MR API(SCGCQ02103183)
 - Add MFI STAT and MR Event for Secure Boot indicating fw dl was not allowed due to an existing pending key change(SCGCQ02103973)
 - Better error message for certain unmap operations(SCGCQ02111563)
 - OEM request to implement slot based device ID for direct attached or enclosure connected drives(SCGCQ02111943)
 - As per OEM request bypassing the cache for particular workload on 512E drives.(SCGCQ02123808)
 - Add disableOffloadNum field in MR_SNAPDUMP_PROPERTIES struct(SCGCQ02125252)
 - API changes for a better presentation of Atlas to tools(SCGCQ02149380)
 - API changes for Lane Margining(SCGCQ01921241)
 - Standard SCSI Inquiry vendor identification should be “AVAGO_B” for VD that is set as boot device(SCGCQ02030668)
 - Unlocking FDE disk after a power-on-reset (POR(SCGCQ02050712)
 - MR API: Add support bits for currentSpeed and clkMode(SCGCQ02132334)
 - Adding NVACHE messages indicate when SLC format has started and completed(SCGCQ02137048)
 - FW prints SASIOUnitPage 11 during boot up.(SCGCQ02144058)
 - Change the order of DDF header updates when there are errors existing in DDF headers currently on the drive(SCGCQ02124249)
 - Enhance data collection when a MU error is seen(SCGCQ02134251)
 - Unblock and allow the SCSI pass-through commands to bad/failed/offline PDs(SCGCQ02136394)


Version 24.21.0-0097 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE: 24.21.0-0097
BIOS: 6.36.00.3
UEFI Driver: 0x06180203
HII: 03.25.05.12
MR NVDATA: 3.1705.00-0018
iMR NVDATA - 3.1705.01-0012
MR Firmware - 4.680.00-8458
iMR Firmware - 4.680.01-845
MR 6.14

defects:
 SATA PD does not change to failed state after read medium error detected(SCGCQ01624704) 
 - Repetitive OOB and LED prints observed in FW logs(SCGCQ01727104) 
 - FW Crashes when user tries to fetch SMP PassThru Info using Host SLT(SCGCQ01937319) 
 - Do not allow RAID config in JBOD-WB mode and prevent change of personality if WB mode is set(SCGCQ01685447) 
 - dev defect - Setting defaults for JBOD-WB mode and code cleanup(SCGCQ01681100) 
 - Cannot create or mount xfs filesystem using xfsprogs 4.19.x kernel 4.20(SCGCQ02027889) 
 - xfs_info command run on an XFS file system created on a VD of strip size 1M shows sunit and swidth as 0(SCGCQ02056038) 
 - CV going into WT mode during learn after upgrading to versions later than 24.18.0-0021 - FW fault after factory defaults(SCGCQ02060813) 
 - After using hdparm to lock a SATA SSD JBOD drive the drive fails to be unlocked by the MR FW on reboot(SCGCQ02083536) 
 - Kill adapter observed while running target reset on JBOD WB(SCGCQ01789188) 
 - SMp command failure in OOB Path(SCGCQ01927021) 
 - HDET_MR 6.14: OOB - SCSI PassThru Command fails with error code 0x2E	(SCGCQ01936541) 
 - Once pinnedcache is set to off not able to toggle field value in JBOD WB mode(SCGCQ01671213) 
 - PL Fault observed while running target reset on JBOD WB(SCGCQ01676164) 
 - MR 6.14: FW reported incorrect value for max data transfer request size as 4 MB in Storcli app.(SCGCQ02023160) 
 - Kill Adapter observed while running task management on JBOD-WB with IO's	(SCGCQ02009801) 
 - Max number of PDs for PatrolRead to run concurrently should be in range from 1 to MR controller's max configurable PDs(SCGCQ02008420) 
 - Some Configured drives may change to JBOD and Unconfigure Good after Set JBOD=on and reboot(SCGCQ02080101) 
 - MR controller was missing in UEFI after reboot when the bootable JBOD drive was removed(SCGCQ02112533) 
 - MR API - Incorrect value used for MR_DCMD_CTRL_SNAPDUMP_ONDEMAND	(SCGCQ01882581) 
 - MR 6.14 - PD show all StorCLI command fails for UBAD SAS & SATA drives	(SCGCQ01915285) 
 - With ESXi 6.7 OS or latter, a SATA SSD drive that is configured as EPD will be dropped by OS when driver reload is done(SCGCQ01969605) 
 - Dev defect: Incorporate the new changes done in MR API(SCGCQ01760667) 
 - Amber LED not seen for UBAD PD's	(SCGCQ01770256) 
 - Continuous SRAM correctable error prints followed by controller reset(SCGCQ02023839) 
 - Able to create RAID configuration even after it has been disabled(SCGCQ01670086) 
 - With a pending personality change, Global hot spares are allowed to be created and should be blocked.(SCGCQ01750315 port of SCGCQ01742187)
 - SMP pass through not working when the “PD 0” is BAD drive(SCGCQ01945674 port of SCGCQ01945602)
 - (CSETActivity) - MCTP over PCIe discovery(SCGCQ01904092 port of SCGCQ01184923)
 - CIT: Same EID assigned to 2 930-8i controllers(SCGCQ01886616 port ofSCGCQ01830180 )
 - Controller OCR seen when DM multipathing issues read CDB with zero blocks(SCGCQ01822167 port of SCGCQ01808882)
 - Unable to recover config when changing security password before re-inserting drives(SCGCQ01874302 port of SCGCQ01715058)
 - 23=Flash programming error while upgrading the Controller FW causes the APP image corruption(SCGCQ02085501 port of SCGCQ02074630)
	
EnhancementRequest:	
 - RTTrace Enable/Disable API changes(SCGCQ01830211) 
 - MR API changes to support EKMS over OOB(SCGCQ01874035) 
 - API Changes for Driver/FW DCMD HandShake(SCGCQ01841266) 
 - Added new events for unmap policy change(SCGCQ01871912) 
 - Add secure boot key update complete event(SCGCQ01928254) 
 - Including The Time Stamp for every Snap Dump created in the firmware.(SCGCQ01797424) 
 - Unmap: Define new events for enhanced UNMAP support [MR7.8](SCGCQ01803319) 
 - Deprecate the snap dump fields that are no longer needed for MR_SNAP_DUMP_PROPERTIES structure(SCGCQ01816724) 
 - [MR 7.8] API change to return apt failure status for a personality change request(SCGCQ01853480) 
 - Interrupt coalsecing setting per group of 8 replies queues (h/w VF registers	(SCGCQ01886424) 
 - HDET: Support smp passthrough storeliboob (API changes requirement(SCGCQ01916035) 
 - Add secure boot support(SCGCQ01792416) 
 - API change to provide learn complete timestamp(SCGCQ01845269) 
 - POC in 6.14: WB support and Pinned Cache changes(SCGCQ01581022) 
 - Aero FW - Reporting SSD wear gauge values for OEM specific customers(SCGCQ01798686) 
 - Support SC_INQUIRY and SC_LOG_SENSE SCSI Passthrough commands on drives in bad state for a particular OEM(SCGCQ01888257) 
 - FW changes for the configurable parameters(SCGCQ01609320) 
 - Add the API to clear all the snap-dumps from firmware.(SCGCQ01824135) 
 - API Changes - After Vision PSOC FW update, applications should ask the user for power cycle instead of reboot(SCGCQ01765150) 
 - Add new MFI Status - MFI_STAT_PD_NOT_ELIGIBLE_FOR_LD	(SCGCQ01818580) 
 - HDET: Support smp passthrough in storlib and storeliboob	(SCGCQ01799154) 
 - Fail the drive and do not pin the cache(SCGCQ01584411) 
 - Integrated Invader PL RO - SCGCQ02000507– phase 14, Version 14.00.11.00 to MR 6.14(SCGCQ02000920) 
 - [MR 7.8] API change to export "disable least latency mode"(SCGCQ01887495) 
 - Fix MR_CTRL_INFO to support backward compatibility(SCGCQ01946548) 
 - Added customer serial number field to MFC Manufacturing 2 structure(SCGCQ01873417) 
 - Added Support for Triggering SnapDump(SCGCQ01848759) 
 - Add Board Support Package Image Type to MR_IMAGE_TYPE(SCGCQ01931637) 


Version 24.21.0-0084-1 - Moderate Impact/Low Probability of Occurrence
--------------------

PACKAGE: 24.21.0-0084
BIOS: 6.36.00.3
UEFI Driver: 0x06180203
HII: 03.25.05.11
NVDATA: 3.1705.00-0018
iMR NVDATA - 3.1705.01-0012
Firmware - 4.680.00-8434
iMR Firmware - 4.680.01-8435
MR 6.14 
Defects:
- SATA SSD not discovered by OS during hibernate test.(SCGCQ01949781)
- Intruder and Invader controllers returnning vpd86 error.(SCGCQ01929277)
- FW reports that the board passed BBU Retention test on boards that have a non operational ONFI NAND memory.(SCGCQ01891177 Port Of Defect SCGCQ01934351)
- Invader IMR : PD fails to get marked as foreign on insertion.(SCGCQ01950845 Port Of Defect SCGCQ01955263)
- Preserved Cache doesn't flush back during Foreign Import.(SCGCQ01466831 Port Of Defect SCGCQ01904085)


Version 24.21.0-0076-1 - Moderate Impact/Low Probability of Occurrence
--------------------

PACKAGE: 24.21.0-0076 
BIOS:  6.36.00.3
UEFI Driver: 0x06180203
HII:  03.25.05.10
NVDATA: 3.1705.00-0018
iMR NVDATA - 3.1705.01-0012
Firmware - 4.680.00-8417
iMR Firmware - 4.680.01-8406

Defects (8)
- 'CacheVault Flash Size' is showing as 3.0 GB after upgrading FW when it should show 4.0 GB.(SCGCQ01615779)
- criteo: Storcli shows R0 VD as WB in JBOD personality where as FW shows in WT mode.(SCGCQ01714445)
- Revert code changes from CSET SCGCQ01569257.(SCGCQ01717743)
- Customer specific 3108 PCIe add-on card fails to come back while resuming from sleep state S.(SCGCQ01718911)
- FW returns success for enabling encryption when it is failed on the drives.(SCGCQ01830718)
- Line 535 in ../../raid/cachePreserve.c for trying to create Pinned Cache by Cable Pull..(SCGCQ01839662)
- memset the deviceStateLedBitmap properly.(SCGCQ01844264)
- OOB SCSI passthru command (READ DEFECT 12) return without response data.(SCGCQ01793262)
- FW is observing Kill Adapter while CCVD disassociate in progress.(SCGCQ01186806 port of SCGCQ01172369)
- Update the MAXTransferLength properly for Driver enabled 1MB support feature.(SCGCQ01238543 port of SCGCQ01232275)
- FW crashes when FW update(OFU) is done with faluty onfi.(SCGCQ01249569 port of SCGCQ01227115)
- irq handler flooding taskqueue and persistent ID removal corrupting memory.(SCGCQ01399132 port of SCGCQ01299784)
- Firmware allows to add bad blcoks beyond actual number of blocks..(SCGCQ01430024 port of SCGCQ01403292)
- MCTP: Addressing PCIe credirt free issue..(SCGCQ01447186 port of SCGCQ01446811)
- Firmware discovery is not listing all the drives after removal/insert Enclosure Cable with IO.(SCGCQ01579250 port of SCGCQ01555943)
- MR FW memory Leak across driver load/unload.( SCGCQ01579251port of SCGCQ01573393)
- With controller operating in least latency mode, FW hits montask upon running IOs.(SCGCQ01587048 port of SCGCQ01116419)
- Increase the recon BB list entries to align with BBM MAX BAD entries.(SCGCQ01635416 port of SCGCQ01623254)
- Issue: JBOD devices were dropped after unloading driver and reloading driver in linux.(SCGCQ01639846 port of SCGCQ01566087)
- : FW asserts when invalid parameters to set excluded ld for CC is sent to firmware..(SCGCQ01670394 port of SCGCQ01635729)
- Colusa SAS expander reset results in unpredictable performance.(SCGCQ01697517 port of SCGCQ01455811)
- MR 7.6 - "NVCache has gone bad" during POST after flashing the latest package 1226 and rebooted.(SCGCQ01714326 port of SCGCQ01635062)
- When NVRAM value is read from cached address ,primary core reads stale value and skips writing to NVRAM..(SCGCQ01715349 port of SCGCQ01676080)
- F/W Hangs during reboot.(SCGCQ01716602 port of SCGCQ01616551)
- MR7.6: Firmware hit montask running task management reset in loops.(SCGCQ01727364 port of SCGCQ01675742)
- When NVRAM value is read from cached address ,primary core reads stale value and skips writing to NVRAM.(SCGCQ01729680 port of SCGCQ01676080)
- LAS does not show proper state of secured locked drives..(SCGCQ01732045 port of SCGCQ01615781)
- F/W Hangs during reboot.(SCGCQ01758976 port of SCGCQ01616551)
- Pd firmware download timer is calculated accordingly.(SCGCQ01758988 port of SCGCQ01669508)
-.(SCGCQ01763953 port of SCGCQ01749090)
- Smart Return Status passthru command failed on SATA drives.(SCGCQ01806402 port of SCGCQ01555033)
- LAS does not show proper state of secured locked drives..(SCGCQ01807819 port of SCGCQ01615781)
-.(SCGCQ01838484 port of SCGCQ01807938)
- 9460-8i is reporting Chip Temperature of 255 when the ambient temp is about 0 C.(SCGCQ01850339 port of SCGCQ01565568)
- Found invalid event.(SCGCQ01375915 port of SCGCQ01347858)
- 9460-16i disappears from F1 setup after encrypting SED.(SCGCQ01565312 port of SCGCQ01326871)
- Sanitize Support.(SCGCQ01577753 port of SCGCQ01526323)
- Increase the recon BB list entries to align with BBM MAX BAD entries.(SCGCQ01633668 port of SCGCQ01623254)
- Sanitize progress in TTY log showing incorrect elapsed time.(SCGCQ01681594 port of SCGCQ01630577)
- Pd firmware download timer is calculated accordingly.(SCGCQ01682987 port of SCGCQ01669508)

EnhancementRequests (11)
- Integrate phase 12 PL (12.00.13.00) with MR 6.12.(SCGCQ01580766)
- FW change: Request to add NVDATA and PNP IDs for new card introduction.(SCGCQ01826466)
- Integrate Intruder Phase 14 PL - 14.00.10.00 Firmware MR PL Release.(SCGCQ01764776)
- Criteo: API changes reversal.(SCGCQ01760512)
- PL Integration: Integrate Intruder PL phase 13.00.10.00 with MR 6.13 Intruder.(SCGCQ01698033)
- PL Integration : Integrate Invader phase 12.00.14.00 PL with MR 6.12.(SCGCQ01716598)
- RTTrace API Changes.(SCGCQ01745568)
- Mixing Rules for SED and non-SED drives to create non-secure array with controller security enabled..(SCGCQ01757538)
- Unmap: Define new API for enhanced UNMAP support.(SCGCQ01758062)
- Adding API bit to indicate whether forced personality change is supported or not..(SCGCQ01762153)
- PL Integration: Integrate Invader Phase 13.00.10.00 PL with MR 6.13 Invader.(SCGCQ01698045)


Version 24.21.0-0052-1 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE:  24.21.0-0052
BIOS:  6.36.00.2
UEFI Driver:  0x06180202
HII:  03.25.05.04
NVDATA: 3.1705.00-0014
iMR NVDATA - 3.1705.01-0011
Firmware - 4.680.00-8353
iMR Firmware - 4.680.01-8354

Defects (42)
- Intruder Controller Disappear during clean shutdown on OEM server.(SCGCQ01375977)
-.(SCGCQ01753405)
-.(SCGCQ01749090)
- When NVRAM value is read from cached address ,primary core reads stale value and skips writing to NVRAM..(SCGCQ01676080)
- Pd firmware download timer is calculated accordingly.(SCGCQ01669508)
- IO path function accessed by both core is not synchonized..(SCGCQ01640234)
- False alarm of "cache Discarded" when the System, with Invader controller + WT R5 volume, is shutdown normally..(SCGCQ01627751)
-.(SCGCQ01623408)
- Increase the recon BB list entries to align with BBM MAX BAD entries.(SCGCQ01623254)
- MR FW memory Leak across driver load/unload.(SCGCQ01573393)
- Incorrect Micron NAND Model Number read from flash.(SCGCQ01531136)
- MR_6.14 PACK 23 - On performing a cable pull/push operation during drive is in failed state, result to MonTask.(SCGCQ01529830)
- [Factory issue] MR 3108 controller BIOS stop at 3 different initialization screen.(SCGCQ01497858)
- IO access to iMR FW will fail after sveral powercycle.(SCGCQ01494761)
- iMR Compilation fails even with RELEASE option in 6.12 after taking errata MR workaround SCGCQ01323607 and its child defects.(SCGCQ01494566)
- SED Drive become UBad during secure erase on MegaRAID 9361-8i controller.(SCGCQ01473188)
- 6.14 : Reverting the sysDma changes.(SCGCQ01465727)
- On iMR Invader & for 2 enclosures connected in cascaded multi path , power off and then power on the 1st enclosure, PDs not getting detected.(SCGCQ01455949)
- Firmware upgrade/downgrade operation failing on SKINNY controller.(SCGCQ01455133)
- MCTP: Addressing PCIe credirt free issue..(SCGCQ01446811)
- Parameter Page Invalid, Setting channel count based on DDR Size..(SCGCQ01440768)
- FW breaks into montaks with pinned cache and foreign configuration.(SCGCQ01378970)
- FW reported tmm Date of Manufacture 15/25/6.(SCGCQ01395084)
- Interrupting Offload will Lead to Next offload cycle to fail.(SCGCQ01399701)
- Enable WB support via API.(SCGCQ01405242)
- F/W Hangs during reboot.(SCGCQ01616551)
- iMR compilation breaks, exceeding 1MB flash region allocated.(SCGCQ01520940)
- Extend iMR change of trap related data should be in same module as trap ISR..(SCGCQ01514867)
- Workaround for IO access to iMR FW will fail after sveral powercycle on 3004 controller..(SCGCQ01507504)
- linker error resolved.(SCGCQ01472217)
- Problem with I2C Slave communication with external Masters that don’t support slave clock stretching..(SCGCQ01443277)
- MR : Cache data Lost when Term Log is set to "on" and grown bad blocks are there in the controller.(SCGCQ01394288)
-.(SCGCQ01400707)
- Learn cycle shown as active when Learn cycle fails.(SCGCQ01400807)
- Firmware allows to add bad blcoks beyond actual number of blocks..(SCGCQ01403292)
- OCR getting disabled after NVRAM delete.(SCGCQ01719006)
- MCTP : Porting of firmware download fixes from Ventura.(SCGCQ01439651)
- NVCache state not transitioning from 'Faulty' to 'Ok' until after reboot.(SCGCQ01395724)
- Intermittent: On iMR_Invader & cascaded Enclosures, after power off the enclosure, FW holds the PD info and apps display PDs.(SCGCQ01483727)
- controller VPD info is hidden as per OEM request.(SCGCQ01454973)
- SSD SATA JBOD discovered as 0.0MB after re-loading the same driver..(SCGCQ01446965)
- Firmware discovery is not listing all the drives after removal/insert Enclosure Cable with IO.(SCGCQ01555943)
- Infinite loop in onfiSyncModeEnter.(SCGCQ01259314 port of SCGCQ00329024)
- HW workaround implementation for SCGCQ00830272 and SCGCQ01048567.(SCGCQ01326393 port of SCGCQ01323607)
- MR_6.14: Intruder PCI Trapping ISR incorrect logic for config trap address.(SCGCQ01334364 port of SCGCQ01332947)
- Firmware crashes during medium error recovery and Rebuild.(SCGCQ01348660 port of SCGCQ01304521)
- Resulting R0 VD is showing as not consistent after reconstruction..(SCGCQ01348998 port of SCGCQ01288897)
- Imr Invader FW crashes while upgrading from Pkg 24.18.0-0021 to Pkg 24.21.0-0007..(SCGCQ01351814 port of SCGCQ01342601)
- Intruder 4G DDR tuning value has to be changed in MR FW..(SCGCQ01369344 port of SCGCQ01368845)
- Found invalid event.(SCGCQ01375914 port of SCGCQ01347858)
- Placement of an image checkword at data area of NOR flash leads to controller crash.(SCGCQ01375943 port of SCGCQ01375071)
- Block OCR after Clearing NVRAM.(SCGCQ01392471 port of SCGCQ01386919)
- Block OCR after Clearing NVRAM.(SCGCQ01394920 port of SCGCQ01386919)
- SCS/PL debug logs for "rb", "tb", or "dmdiag pl dbg" are sometimes mangled due to multiple mprintf's overlapping.(SCGCQ01399457 port of SCGCQ01283702)
- RedBrick controller hang at DCR Err Logg Address 29e02..(SCGCQ01412795 port of SCGCQ01375159)
- RedBrick controller hang at DCR Err Logg Address 29e02..(SCGCQ01412827 port of SCGCQ01375159)
- LSA hangs when user try to change drive security key..(SCGCQ01412848 port of SCGCQ01342655)
- B200M4 (Carmel/ 3108 iMR): driver crashed after FW update via UCSM (UCSM bundle 2.2(8fS2)A/B to 3.1(2.163)A/B).(SCGCQ01412896 port of SCGCQ01271186)
- Parameter Page Reads fail during ONFI bringup..(SCGCQ01415428 port of SCGCQ01413557)
- heck Consistency doesn't identify double media errors once aborting and starting CC again.(SCGCQ01421932 port of SCGCQ01411591)
- heck Consistency doesn't identify double media errors once aborting and starting CC again.(SCGCQ01421933 port of SCGCQ01411591)
- heck Consistency doesn't identify double media errors once aborting and starting CC again.(SCGCQ01421934 port of SCGCQ01411591)
- Revert the DDR tuning values back to default value.(SCGCQ01446963 port of SCGCQ01444640)
- PL considers Timer Handle=0 and invalid, MR FW did not..(SCGCQ01446983 port of SCGCQ01399026)
- MCTP: Addressing PCIe credirt free issue..(SCGCQ01447187 port of SCGCQ01446811)
- Parameter Page Invalid, Setting channel count based on DDR Size..(SCGCQ01447901 port of SCGCQ01440768)
- Drives in Enclosure spin up values for OEM board is not initialized correctly.(SCGCQ01466081 port of SCGCQ01450221)
- IOMMU fault at address 0x80360000.(SCGCQ01473355 port of SCGCQ01279547)
- Enable DO_REAL_TIME_ISP and DO_DISABLE_ISP_CLAMP flags while flashing CPLD for Intruder cards.(SCGCQ01503730 port of SCGCQ01452026)
- SED Drive become UBad during secure erase on MegaRAID 9361-8i controller.(SCGCQ01503736 port of SCGCQ01473188)
- [Factory issue] MR 3108 controller BIOS stop at 3 different initialization screen.(SCGCQ01519905 port of SCGCQ01497858)
- MR_6.14 PACK 23 - On performing a cable pull/push operation during drive is in failed state, result to MonTask.(SCGCQ01532358 port of SCGCQ01529830)
- OCR is disabled by default is RC build, even NVDATA if it is enabled..(SCGCQ01540279 port of SCGCQ01503204)
- MR7.1/7.3 Termlog/UARTlog - messages sometimes missed in Termlog.(SCGCQ01540361 port of SCGCQ01498188)
-.(SCGCQ01569257 port of SCGCQ01097035)
- If an INVALID applicationMsgTag id received, then failed the command with MFI_OOB_STATUS_INVALID_CMD using command id MAX_OOB_COMMANDS..(SCGCQ01575976 port of SCGCQ01337332)
- Sanitize Support.(SCGCQ01577752 port of SCGCQ01526323)
- SATA PassTrough commands with check condition taking long time to complete..(SCGCQ01582512 port of SCGCQ01561887)
- VMware Passthrough Adapter does not sync time on VM power on.(SCGCQ01595865 port of SCGCQ01592800)
- Jbod become Ugood sometimes after reboot.(SCGCQ01616609 port of SCGCQ01508978)
- Colusa SAS expander reset results in unpredictable performance.(SCGCQ01618030 port of SCGCQ01455811)
- 'CacheVault Flash Size' is showing as 3.0 GB after upgrading FW when it should show 4.0 GB.(SCGCQ01640816 port of SCGCQ01615779)
- Drives are reverted back to JBOD after perfoming instant secure erase.(SCGCQ01683366 port of SCGCQ01615777)
- MR7.1/7.3 Termlog/UARTlog - messages sometimes missed in Termlog.(SCGCQ01714377 port of SCGCQ01498188)
- In HII whether entering the correct pass phrase or the wrong pass phrase a secured SED becomes unsecured.(SCGCQ01715297 port of SCGCQ01301947)
- B200 M5 / Carmel (3108 iMR) - VSAN failure during controller reset test.(SCGCQ01760837 port of SCGCQ01397566)
- MR 6.14 Beta: MonTask: line 245 in file ../../raid/1078int.c while running reboot test with background operations.(SCGCQ01339329 port of SCGCQ01332706)
- MR : Cache data Lost when Term Log is set to "on" and grown bad blocks are there in the controller.(SCGCQ01403930 port of SCGCQ01394288)
- Interrupting Offload will Lead to Next offload cycle to fail.(SCGCQ01403958 port of SCGCQ01399701)
- SSD SATA JBOD discovered as 0.0MB after re-loading the same driver..(SCGCQ01447007 port of SCGCQ01446965)
- MCTP : Porting of firmware download fixes from Ventura.(SCGCQ01447173 port of SCGCQ01439651)
- Controller crash observed while running OLTP workload (4K and 16K 16QD).(SCGCQ01447780 port of SCGCQ01438216)
- PL considers Timer Handle=0 and invalid, MR FW did not..(SCGCQ01467708 port of SCGCQ01399026)
- [Factory issue] MR 3108 controller BIOS stop at 3 different initialization screen.(SCGCQ01519906 port of SCGCQ01497858)
- Extend iMR change of trap related data should be in same module as trap ISR..(SCGCQ01521684 port of SCGCQ01514867)
- Event Log Corruption..(SCGCQ01532399 port of SCGCQ01451417)
- Rebuild Rate %100 takes much longer time than %30 while running IO. It should take much shorter time..(SCGCQ01540424 port of SCGCQ01336908)
- Controller crash observed while running OLTP workload.(SCGCQ01565253 port of SCGCQ01447773)
- OEM iMR 8i controller fails to complete an OCR.(SCGCQ01565318 port of SCGCQ01330611)
- Snap3 : Drives drops while running transformation operation on R1 to R5 with 900 Medium errors.(SCGCQ01598538 port of SCGCQ01581661)
- LSA shows Stop Erase option for VDs on which Erase operation is not in progress.(SCGCQ01605097 port of SCGCQ01600267)
- Memset the PinnedDataStructure when DRAM dirty signature is zero.(SCGCQ01724925 port of SCGCQ01713149)
- Firmware crashes during medium error recovery and Rebuild.(SCGCQ01348657 port of SCGCQ01304521)
- Firmware crashes during medium error recovery and Rebuild.(SCGCQ01348658 port of SCGCQ01304521)
- FW is not correctly reporting Hide VD operation as not supported.(SCGCQ01348841 port of SCGCQ01274084)
- MR7.3: 4k PD Configuration can't be imported from iMR to MR Controller. However, it can be imported from MR to iMR.(SCGCQ01402828 port of SCGCQ01395842)
- PL considers Timer Handle=0 and invalid, MR FW did not..(SCGCQ01467725 port of SCGCQ01399026)
- Extend iMR change of trap related data should be in same module as trap ISR..(SCGCQ01520788 port of SCGCQ01514867)
- MR 7.6 - "NVCache has gone bad" during POST after flashing the latest package 1226 and rebooted.(SCGCQ01683358 port of SCGCQ01635062)
- Controller hang with FDE Drive (Micron 510DC).(SCGCQ01328038 port of SCGCQ01304133)
- Assertion failure in ../../mros/mem.c : mb->tag==tag.(SCGCQ01539460 port of SCGCQ01515324)
- Parameter Page Reads fail during ONFI bringup..(SCGCQ01415424 port of SCGCQ01413557)
- If an INVALID applicationMsgTag id received, then failed the command with MFI_OOB_STATUS_INVALID_CMD using command id MAX_OOB_COMMANDS..(SCGCQ01512549 port of SCGCQ01337332)


EnhancementRequests (47)
- New events for PR/CC conflicts and sector size mismatch.(SCGCQ01227051)
- Provide customized default smartpollinterval to 30 for iMR3004 product.(SCGCQ01748252)
- RTTrace API Changes.(SCGCQ01745568)
- API changes needed to support eHBA product series.(SCGCQ01727346)
- Create sanitize events.(SCGCQ01713708)
- Memset the PinnedDataStructure when DRAM dirty signature is zero.(SCGCQ01713149)
- Integrate latest phase 14.0 - 14.00.08.00 PL with MR 6.14.(SCGCQ01682170)
- as per customer request enabled FBU02 and 4G TFM support.(SCGCQ01681106)
- Modify event string APIs for MISSING and OFFLINE LDs.(SCGCQ01628177)
- New configuration params added for EPD-PT devices.(SCGCQ01599607)
- MR API change request to Enable/disable the parallel PD FW update feature based on PNP ID’s.(SCGCQ01595347)
- Integrate latest phase 14 PL with MR 6.14.(SCGCQ01593998)
- Integrate Invader Phase 14 PL - 14.00.06.00 Firmware MR PL Release.(SCGCQ01589431)
- Add support to defeature Cached I/O policy.(SCGCQ01581032)
- Implement Snapdump debugging capability.(SCGCQ01567770)
- Integrate Intruder phase 14 PL - 14.00.08.00 with MR 6.14 Intruder.(SCGCQ01459161)
- customer request for GPIO support..(SCGCQ01452102)
- Enable DO_REAL_TIME_ISP and DO_DISABLE_ISP_CLAMP flags while flashing CPLD for Intruder cards.(SCGCQ01452026)
- Fail to Set SSDSmartErEnabled to TRUE when copyback is disabled.(SCGCQ01403999)
- PL 14.00.07.00 intgration to MR 6.14 intruder..(SCGCQ01401110)
- Integrate phase 14 Intruder PL - 14.00.06.00 with MR 6.14.(SCGCQ01386225)
- Add "Incompatible with Profile" event.(SCGCQ01289924)
- Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01216848)
-.(SCGCQ01389581)
- Add Test Link Diagnostic API.(SCGCQ01436268)
- Add a new structure to provide OEMs ability to switch to select either I2C or PCIe as an out of band transport.(SCGCQ01445048)
- Provide OEMs ability to select either I2C or PCIe as an out of band transport.(SCGCQ01450245)
- Update description of MR_DCMD_CTRL_PERSONALITY_SET Dcmd.(SCGCQ01467149)
- Add support for API fields to report SED type of PD.(SCGCQ01587230)
- Add OnOff parameter in Properties2 of Structure MR_CTRL_PROP to enable/disable mix of Enterprise & Opal SED drives.(SCGCQ01593520)
- NVDATA parameter to OPAL SED.(SCGCQ01614689)
- Added a new interface between driver-aops to indicate if 64 bit SGL support is enabled.(SCGCQ01620350)
- Add new MFI Status to block requested operation due to existing controller configuration.(SCGCQ01670135)
- Change the mr.h API comment showing the new return status for the - MR_DCMD_PD_GET_INFO.(SCGCQ01670234)
- API change for Switch attached NVMe HW RAID support for Supermicro backplanes.(SCGCQ01697667)
- Request to enable JBOD for Rambler PNP ID.(SCGCQ01727448)
- Reverted the DDR tuning values.(SCGCQ01625968)
- Porting the changes of NVRAM_Struct from MesaVerde stream to 6.14.(SCGCQ01563144)
- Enhance Messaging Unit error ISR to dump debug information of virtual functions having error.(SCGCQ01553249)
- CacheCade: IO performance need to be improved for WB SVD and WB CCVD combination for specific PnP ID.(SCGCQ01472061)
- FW breaks into montaks with pinned cache and foreign configuration.(SCGCQ01403814)
- Boot message string change for BOOT_MSG_CACHE_DISCARD.(SCGCQ01394348)
- Block OCR after Clearing NVRAM.(SCGCQ01386919)
- PL 14.00.05.00 Integration with Invader MR 6.14.(SCGCQ01384265)
- Added MR_MFC_DEFAULTS.NVMeAbortTO and MR_MFC_DEFAULTS.NVMeMaxControllerResetTO.(SCGCQ01532045)
 FW to fail back host command for the wrong value.(SCGCQ01575960)
- Setting DDR flag for ROMB design having new DDR for an OEM.(SCGCQ01466802)


Version 24.21.0-0016 - Moderate Impact/Low Probability of Occurrence
--------------------
PACKAGE:  24.21.0-0016
BIOS:  6.36.00.1_4.19.08.00_0x06180202
UEFI Driver:  0x06180202
HII:  03.25.05.03
NVDT:  3.1705.00-0005
MR FW:  4.680.00-8258

Fixes:
 -  MR 6.13: Blocked Spin down Pass thru command for configured drives.(SCGCQ01201958)
 -  In RAID personality, MR_DCMD_CFG_AUTOCFG DCMD is disabled in non(SCGCQ01213915)
 -  Setting all the ldtoTgtId with 0xff beyond 240 entries.(SCGCQ01215003)
 - (SCGCQ01219438)
 -  MR_EVT_PD_ERROR_STATS events are logged when drive is moved to REBUILD/UNCONFIGURED BAD/ONLINE/OFFLINE. Also correct DCMD(SCGCQ01223284)
 -  FW crashes when FW update(OFU) is done with faluty onfi(SCGCQ01227115)
 -  Coverity issues:fixed the coverity defects.(SCGCQ01230560)
 -  Update the MAXTransferLength properly for Driver enabled 1MB support feature(SCGCQ01232275)
 -  Assertion failure in ../../dm/mpt2/mptrec.c at line 3139, while performing cable pull/push operation.(SCGCQ01235505)
 -  corrected the span index(SCGCQ01236287)
 -  Coverity issue 15748 and 17765(SCGCQ01241568)
 -  Drive Strength values are incorrect for last 8 phys of Red Brick Controller(SCGCQ01241680)
 -  Change Slew Rate on dual rank RedBrick Boards to fix ECC Errors.(SCGCQ01242817)
 -  Cache Data lost if power loss happens during descriptor preparation.(SCGCQ01253076)
 -  'C0:mr_wakeup: mem 45569e20, cache line ffffffff' observed while running BGI on RAID 5 Volume with media errors.(SCGCQ01256120)
 -  Assertion failure in ../../raid/2108vI2o.c at line 2398 on flashing firmware(SCGCQ01258563)
 -  Dev defect to address action items identified during Ventura(SCGCQ01260609)
 -  Dev defect to handle HW action items identified during Intruder(SCGCQ01261213)
 -  Cache data Lost when Term Log is set to "on"(SCGCQ01261426)
 -  6.13 ONFI_PORT: If power loss occurs after OCR, FW might lose tty log.(SCGCQ01262834)
 -  6.13_ONFI_PORT: Program the erase and wait count values during ONFI Initialization.(SCGCQ01262883)
 -  6.13 ONFI PORT :Set bit 0 in global Interrupt Register so that host will receive an interrupt.(SCGCQ01262884)
 -  Flash File System Reads fail after system reset.(SCGCQ01267220)
 -  FW does not remember user induced bad blocks across boots.(SCGCQ01267700)
 -  MR 6.13(SCGCQ01268066)
 -  Unable to access device PD (SSD)(SCGCQ01268412)
 -  MR_6.13:FW flash pack (SCGCQ01273216)
 -  Cache Restore fails if supercap is removed while cache offload is in Progress.(SCGCQ01274494)
 -  Unable to set termlog on/off from storcli intermittently on Intruder Armstrong board.(SCGCQ01278512)
 -  Storcli Failed to create single PD R0 from UGood drive which has replaced a UBAD foreign drive(SCGCQ01282181)
 -  Intruder : After Termlog Toggling with power cycle, result to ERROR: Dirty disk cache data has been lost(SCGCQ01282319)
 -  Modify Read Eye Training Algorithm to make it spec compliant.(SCGCQ01283719)
 -  High DB and Log write(SCGCQ01285311)
 -  Coverity reported an uninitialized variable(SCGCQ01285595)
 -  OS hung and iMR FW reset when do delete and create VD from previous powersave PD (Spindowned)(SCGCQ01287286)
 -  Reboot the system with 240 R0 Volumes and changing the mode(SCGCQ01288297)
 -  PL Fault 0000601e observed while running multipath on/off script in JBOD mode.(SCGCQ01288781)
 -  erase types and startSecureEraseNonSED is set accordingly(SCGCQ01289147)
 -  Modify NVDATA boot message to rename 'NVDATA image' to 'firmware image'(SCGCQ01290201)
 -  Cache data lost event seen for WT vds(SCGCQ01313607)
 -  Kill adapater observed while running IO's on 240 Volumes(SCGCQ01313950)
 -  Coverity: Fixing Coverity defect 16148(SCGCQ01316152)
 -  Fixing the coverity raised issue(SCGCQ01318465)
 -  Coverity issue 19341(SCGCQ01319291)
 -  HW workaround implementation for SCGCQ00830272 and SCGCQ01048567(SCGCQ01323607)
 -  auto config is not happening in some cases after issuing storcli /cx set autopdcache=r0(SCGCQ01323848)
 -  MR 6.14 Beta: MonTask: line 245 in file ../../raid/1078int.c while running reboot test with background operations(SCGCQ01332706)
 -  MR_6.14: Intruder PCI Trapping ISR incorrect logic for config trap address(SCGCQ01332947)
 -  ntruder: Fix the Intruder Boot Block compilation and warning issue.(SCGCQ01334292)
 -  Imr Invader FW crashes while upgrading from Pkg 24.18.0(SCGCQ01342601)
 -  No amber LED when a configured disk is removed(SCGCQ01343017)
 -  Controller fails to boot up when migrated from 6.13 to 6.14 FW for Specific OEM(SCGCQ01348114)
 -  Value defined for the DDR turning parameter DP_IO_VREF_1_2 is wrong for invader boards(SCGCQ01350295)
 -  MR_INVADER_WORKAROUND_PCIE_IGNORE_REPLY_PARITY_ERROR macro definition missing(SCGCQ01351483)
 -  Intruder 4G DDR tuning value has to be changed in MR FW.(SCGCQ01368845)
 -  Lenovo Sebastian Fatal Firmware error when connecting to straight without Group ID support.(SCGCQ01204592)
 -  FW does not fail unsupported erase type for a PD(SCGCQ01221549)
 -  Allow Cyrpto erase on non(SCGCQ01222318)
 -  Fix coverity reported issue(SCGCQ01227079)
 -  FW is not updating EPDs list exposed to host after drives removal event is posted which is causing dev nodes are not getting deleted on drive removal(SCGCQ01230441)
 -  Diagnostics report of iMR Invader contains information about R6 and R60 is set to 0(SCGCQ01235661)
 -  Enable MR_DCMD_PD_ERROR_STATS and the event MR_EVT_PD_ERROR_STATS only for direct attached drives(SCGCQ01237252)
 -  DATA TLB ERROR, While connecting controller each Port to Back(SCGCQ01252111)
 -  MR 6.13.1Alpha:Probable Drive/cable issue Event not printed in firmwarelogs on triggering drive/cable error when connected BP(SCGCQ01256005)
 -  Handling of DCR errors in MSS core(SCGCQ01263110)
 -  Controller does not boot up while performing cache offload .(SCGCQ01278480)
 -  Controller cache discarded due to memory/battery problem(SCGCQ01280181)
 -  Perf(SCGCQ01283507)
 -  Code review: turn off the onfi when bbu is bad(SCGCQ01297565)
 -  Coverity issues 19244, 19245, 19246 and 19248(SCGCQ01299214)
 -  MR 6.14 Intruder(Vail): Intruder Controller hangs in primary core on reboot in Dell Power Edge T620 server.(SCGCQ01299482)
 -  Fix coverity issue 19253 Structurally dead code in checkCacheOffloadStatus, raid/1078init.c(SCGCQ01300678)
 -  coverity defects fixed(SCGCQ01300689)
 -  To fix coverity issue 17759(SCGCQ01317039)
 -  Found invalid event(SCGCQ01347858)
 -  Placement of an image checkword at data area of NOR flash leads to controller crash(SCGCQ01375071)
 - (SCGCQ01227044)
 -  FC: 0 CS: 0 offload meta signature not valid, ffffffff observed in FW logs on a system restart.(SCGCQ01299424)
 -  MR 6.14 (SCGCQ01300667)
 -  Coverity issue 15356(SCGCQ01301658)
 -  update the boundary values in UpdateFeatureSetValues()(SCGCQ01209605)
 -  FW hang finaly leading to kill adatper with inBox driver(SCGCQ01250342)
 -  MR7.1_NVMe: After foreign import of 64 R0 VDs, operating system unable to discover the VDs(SCGCQ01229929 Port Of SCGCQ01209394)
 -  FW crashes when FW update(OFU) is done with faluty onfi(SCGCQ01235056 Port Of SCGCQ01227115)
 -  Server (Purley): Controller (16i) (SCGCQ01235753 Port Of SCGCQ01200311)
 -  In RAID personality, MR_DCMD_CFG_AUTOCFG DCMD is disabled in non(SCGCQ01237142 Port Of SCGCQ01213915)
 -  Storcli failed to stop drives LED locating with a range(SCGCQ01241870 Port Of SCGCQ01051728)
 -  MR7.1_NVMe: After foreign import of 64 R0 VDs, operating system unable to discover the VDs(SCGCQ01242766 Port Of SCGCQ01209394)
 -  unable to encrypt disk when using no pass(SCGCQ01245596 Port Of SCGCQ01144752)
 -  Offline Marked DG (RAID0) appearing in RHEL 7 install(SCGCQ01245782 Port Of SCGCQ00995384)
 -  SAS2208 card reset in DataCenter due to unknown reason(SCGCQ01247264 Port Of SCGCQ01240574)
 -  RDM in Use(SCGCQ01255837)
 -  ONFI: To properly handle the OCR case with RESET Status Register.(SCGCQ01259337 Port Of SCGCQ00665475)
 -  ONFI BBLIST:ONFI BadBlocks: COL disarmed, VDs remain in WB mode, no Administrative Messages to bad flash part.(SCGCQ01260470 Port Of SCGCQ01235856)
 -  Firmware halts upon changing controller personality to JBOD mode with MCTP enabled(SCGCQ01260889 Port Of SCGCQ01252243)
 -  Infinite loop in onfiSyncModeEnter(SCGCQ01260995 Port Of SCGCQ00329024)
 -  FW crashes when setting fwtermlog bbu=on to a card with bad NAND flash(SCGCQ01261425 Port Of SCGCQ01129530)
 -  Insertion of the boot messages and the evets for montoring the ONFI backup capacity.(SCGCQ01263212 Port Of SCGCQ00433463)
 -  'C0:mr_wakeup: mem 45569e20, cache line ffffffff' observed while running BGI on RAID 5 Volume with media errors.(SCGCQ01263800 Port Of SCGCQ01256120)
 -  Handling of DCR errors in MSS core(SCGCQ01263859 Port Of SCGCQ01263110)
 -  Invalid date for next learn cycle is set due to invalid date from OEM server (STF: Next learn time is 1970(SCGCQ01264476 Port Of SCGCQ01152321)
 -  GetAllLDAllowedOperation call in Storelib is not returning Allowed operations when some LDs are deleted(SCGCQ01265445 Port Of SCGCQ01250559)
 -  FD33xD issues in VMWare(SCGCQ01266300 Port Of SCGCQ01203008)
 -  In RAID personality, MR_DCMD_CFG_AUTOCFG DCMD is disabled in non(SCGCQ01274496 Port Of SCGCQ01213915)
 -  MR_6.13:FW flash pack (SCGCQ01280567 Port Of SCGCQ01273216)
 -  unable to encrypt disk when using no pass(SCGCQ01287082 Port Of SCGCQ01144752)
 -  Controller cache discarded due to memory/battery problem(SCGCQ01288848 Port Of SCGCQ01280181)
 -  RAID10 VD goes to failed state after performing RLM(SCGCQ01289123 Port Of SCGCQ01277951)
 -  IN FAILED ARRAY bit is not being set when a VD is cleared(SCGCQ01289194 Port Of SCGCQ01137359)
 -  Storcli Failed to create single PD R0 from UGood drive which has replaced a UBAD foreign drive(SCGCQ01290418 Port Of SCGCQ01282181)
 -  RAID10 VD goes to failed state after performing RLM(SCGCQ01291340 Port Of SCGCQ01277951)
 -  Controller cache discarded due to memory/battery problem(SCGCQ01291492 Port Of SCGCQ01280181)
 -  Cannot stop patrol read on PD with medium errors by the stop cmd(SCGCQ01294884 Port Of SCGCQ01063103)
 -  Perf(SCGCQ01297497 Port Of SCGCQ01283507)
 -  Code review: turn off the onfi when bbu is bad(SCGCQ01297666 Port Of SCGCQ01297565)
 -  Code review: turn off the onfi when bbu is bad(SCGCQ01299260 Port Of SCGCQ01297565)
 -  Perf(SCGCQ01300759 Port Of SCGCQ01283507)
 -  PL Fault 0000601e observed while running multipath on/off script in JBOD mode.(SCGCQ01304919 Port Of SCGCQ01288781)
 -  Firmware:(SCGCQ01306491 Port Of SCGCQ01258853)
 -  6.14 : To fix IOPATH overflow during linking(SCGCQ01311731 Port Of SCGCQ01311464)
 -  Unable to access device PD (SSD)(SCGCQ01321307 Port Of SCGCQ01268412)
 -  OS hung and iMR FW reset when do delete and create VD from previous powersave PD (Spindowned)(SCGCQ01326069 Port Of SCGCQ01287286)
 -  HW workaround implementation for SCGCQ00830272 and SCGCQ01048567(SCGCQ01326394 Port Of SCGCQ01323607)
 -  B200M4 (Carmel/ 3108 iMR): driver crashed after FW update via UCSM (UCSM bundle 2.2(8fS2)A/B to 3.1(2.163)A/B)(SCGCQ01331892 Port Of SCGCQ01271186)
 -  B200M4 (Carmel/ 3108 iMR): driver crashed after FW update via UCSM (UCSM bundle 2.2(8fS2)A/B to 3.1(2.163)A/B)(SCGCQ01332726 Port Of SCGCQ01271186)
 -  MR 6.14 Intruder(Vail): Intruder Controller hangs in primary core on reboot in Dell Power Edge T620 server.(SCGCQ01334334 Port Of SCGCQ01299482)
 -  MR_6.14: Intruder PCI Trapping ISR incorrect logic for config trap address(SCGCQ01334365 Port Of SCGCQ01332947)
 -  MR 6.14 Beta: MonTask: line 245 in file ../../raid/1078int.c while running reboot test with background operations(SCGCQ01339330 Port Of SCGCQ01332706)
 -  Cache data lost event seen for WT vds(SCGCQ01349420 Port Of SCGCQ01313607)
 -  Kill adapater observed while running IO's on 240 Volumes(SCGCQ01350347 Port Of SCGCQ01313950)
 -  No amber LED when a configured disk is removed(SCGCQ01350771 Port Of SCGCQ01343017)
 -  Firmware hits montask while reconstruction when drive is pulled out(SCGCQ01351442 Port Of SCGCQ01260340)
 -  MR 6.13: Blocked Spin down Pass thru command for configured drives.(SCGCQ01351559 Port Of SCGCQ01201958)
 -  IOMMU fault at address 0x80360000(SCGCQ01356192 Port Of SCGCQ01279547)
 -  LSA hangs when user try to change drive security key.(SCGCQ01367331 Port Of SCGCQ01342655)
 -  Invalid date for next learn cycle is set due to invalid date from OEM server (STF: Next learn time is 1970(SCGCQ01241869 Port Of SCGCQ01152321)
 -  MR6.12 NVRAM Overflow (SCGCQ01248969 Port Of SCGCQ01230749)
 -  FD33xD issues in VMWare(SCGCQ01261095 Port Of SCGCQ01203008)
 -  FD33xD issues in VMWare(SCGCQ01263759 Port Of SCGCQ01203008)
 -  Configuration lost and system crashed on having a stale configuration connected(SCGCQ01273187 Port Of SCGCQ01170701)
 -  PL Fault 0000601e observed while running multipath on/off script in JBOD mode.(SCGCQ01304921 Port Of SCGCQ01288781)
 -  FC: 0 CS: 0 offload meta signature not valid, ffffffff observed in FW logs on a system restart.(SCGCQ01351052 Port Of SCGCQ01299424)
 -  Controller fails to boot up when migrated from 6.13 to 6.14 FW for Specific OEM(SCGCQ01351614)
 -  SAS2208 card reset in DataCenter due to unknown reason(SCGCQ01311439 Port Of SCGCQ01240574)
 -  Drive Strength values are incorrect for last 8 phys of Red Brick Controller(SCGCQ01247082 Port Of SCGCQ01241680)
 -  Firmware hits montask while reconstruction when drive is pulled out(SCGCQ01282285 Port Of SCGCQ01260340)
 -  Code review: turn off the onfi when bbu is bad(SCGCQ01299219 Port Of SCGCQ01297565)
 -  Controller does not boot up while performing cache offload .(SCGCQ01288845 Port Of SCGCQ01278480)

 
Enhancements:
 -  New fault code for routine synchronous reset(SCGCQ01264142)
 -  Vail FW not responding to PWR_REQ in time. Request to up the number of TURs sent before timing out drive.(SCGCQ01373161)
 -  Disable OOB communication via I2C(SCGCQ01369359)
 -  Integrate Intruder PL 14.00.04.00 with MR 6.14(SCGCQ01341925)
 -  PL phase 13.0007.00 integration with MR 6.13(SCGCQ01334112)
 -  PL integration(SCGCQ01330898)
 -  Integrate PL phase 14.00.02.00 with MR 6.14(SCGCQ01307233)
 -  Integrate 13.00.06.00 PL to MR 6.13(SCGCQ01304141)
 -  PL integration 12.00.10.00 with MR 6.12(SCGCQ01276465)
 -  Integrated PL 12.0.9.0 with MR 6.12(SCGCQ01268897)
 -  Shift IOPATH code by 4 cache lines to workaround intruder performance issue.(SCGCQ01262698)
 -  PR State Machine Clean up during Patrol Read/Check Consistency Conflicts(SCGCQ01260431)
 -  Integrate intruder PL 13.00.04.00 (SCGCQ01237533)(SCGCQ01238286)
 -  Integrate PL 13.00.04.00 to MR_FW_SAS3_6.13_4G_DDR(SCGCQ01238126)
 -  Open up MR_DCMD_CFG_AUTOCFG for iMR for GET operation(SCGCQ01228949)
 -  Customer requesting digitally signed FW packages on their Intruder controller(SCGCQ01215397)
 -  MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP(SCGCQ01180886)
 -  MPI 2.5: Add two new reason codes to Active Cable Exception Event Data(SCGCQ01208954)
 -  MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0(SCGCQ01213028)
 -  MPI 2.6: Add new firmware download type (CBB BACKUP)(SCGCQ01258005)
 -  MPI 2.6: Device side PCIe SRNS flag(SCGCQ01276256)
 -  MPI 2.6: Add new firmware download type (CPLD IMAGE)(SCGCQ01305760)
 -  IN FAILED ARRAY bit is not being set when a VD is cleared(SCGCQ01137359)
 -  Integrate Intruder PL 13.00.05.00 (RO SCGCQ01263844)(SCGCQ01265401)
 -  Add additional sense data to firmware tracker list(SCGCQ01254954)
 -  Method for determining bad ONFI flash via Storcli & SNMP trap upon NAND flash failure for Aspen and Vail (Invader and Intrude(SCGCQ01219862)
 -  MPI2.6: Mfg7 support for arbitrary starting slot number(SCGCQ01213267)
 -  MPI 2.6: Add Aero PCI Device IDs(SCGCQ01373008)
 -  Isolating faulty cable issue from bad drive issue(SCGCQ01215270)
 -  PL integration(SCGCQ01268896)
 

Version 24.18.0-0046-1 - Moderate Impact/Low Probability of Occurrence
--------------------
BIOS:  6.34.01.0_4.19.08.00_0x06160201
UEFI Driver:  06160201
HII:  E3.23.06.04
NVDT:  3.1611.00-0012
MR FW:  4.670.00-8194
Package: 24.18.0-0046 

- Removed support update via ThinkSystem XClarity Control (XCC) web GUI and Lenovo XClarity Essentials OneCLI -imm option


Version 24.18.0-0046 - New Function Only/No fixes
--------------------
BIOS:  6.34.01.0_4.19.08.00_0x06160201
UEFI Driver:  06160201
HII:  E3.23.06.04
NVDT:  3.1611.00-0012
MR FW:  4.670.00-8194





Lenovo Data Center Group Linux OS Support Home Page
linux.lenovo.com

© 2018-2021 Lenovo. All rights reserved

ThinkSystem RAID and ServeRAID M Series SAS/SATA Controller Driver for SLES 12 (For Sles)



ThinkSystem RAID and ServeRAID M Series SAS/SATA Controller Driver for Linux

This product supports [SLES 12.4,SLES 12.5]

Adapters Supported:
	ThinkSystem RAID 530-8i PCIe 12Gb Adapter  (7Y37A01082)
	ThinkSystem RAID 530-4i Flex Adapter       (7M17A03932)
	ThinkSystem RAID 530-4i Flex Adapter       (7M27A03918)
	ThinkSystem RAID 530-8i Dense Adapter      (SD530 RAID)
	ThinkSystem RAID 530-16i PCIe 12Gb Adapter (4Y37A09727)
	ThinkSystem RAID 730-8i 1GB Cache PCIe 12Gb Adapter  (7Y37A01083)
	ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter  (4Y37A09722)
	ThinkSystem RAID 930-8i 2GB Flash PCIe 12Gb Adapter  (7Y37A01084)
	ThinkSystem RAID 930-16i 4GB Flash PCIe 12Gb Adapter (7Y37A01085)
	ThinkSystem RAID 930-24i 4GB Flash PCIe 12Gb Adapter (7Y37A01086)
	ThinkSystem RAID 930-8e 4GB Flash PCIe 12Gb Adapter  (7Y37A01087)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M17A03933)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M27A03917)
	ThinkSystem  RAID 930-16i 8GB Flash PCIe 12Gb Adapter(4Y37A09721)
	ThinkSystem RAID 940-8e 4GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-8i 4GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-8i 8GB Flash PCIe Gen4 12Gb Adapter
	ThinkSystem RAID 940-16i 4GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-32i 8GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Internal Adapter
	ServeRAID M1210 SAS/SATA Controller    (00JY194)
	ServeRAID M1215 SAS/SATA Controller    (46C9114)
	LSI SAS3004 RAID                       (NA-SAS3004-B)
	LSI SAS3004 RAID                       (NA-SAS3004-N)
	ServeRAID M5210 SAS/SATA Controller    (46C9110)
	ServeRAID M5225-2GB SAS/SATA Controller(00AE938)
	ServeRAID M5215 with 2GB Flash Enablement Flex System x240 M5   (00JX142)
	ServeRAID M5210e SAS/SATA Controller   (46C9117CTO)
	ServeRAID M5120 SAS/SATA Controller    (81Y4478)
	IBM Flex System Storage Expansion Node (68Y8588)
	ServeRAID M5115 SAS/SATA Controller for Flex System  (90Y4390)
	ServeRAID M5100 Series IBM Flex System Flash Kit for X6 (44T1178)


NOTE TO SERVICE - Reference RETAIN #N/A

07.717.02.00-2 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.17

Defects:
-One VD deletion leads to IO blocked to different VD forever.(DCSG00948232 (Port Of Defect DCSG00951388))

EnhancementRequests:
-MR7.17: Driver module signing for RHEL and SUSE.(DCSG00418428)
-Block the IO on Deleted VDs derived from Raid Map update.(DCSG00342297)
-MR7.17: Improve error handling at multiple places in driver.(DCSG00368931)
-MR7.16: Add RHEL7.9 GA support.(DCSG00382600)
-MR7.17: RHEL8.3 GA support.(DCSG00418201)
-Xenserver 8.2 LTSR support.(DCSG00361050)

07.715.03.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.15

Defects:
-MR7.15: silence warnings of IO request frames memory allocation failure.(DCSG00243681)
-MR_7.15: 7.15 ROP os readme file accordance with os support list.(DCSG00249459)
-[9361-8i + MR6.14] (Internal BRCM) Controller Run into Fatal Error Stop at Critical State when run fio to reproduce issue in(DCSG00079487).(DCSG00129711)
-Linux_Drv_BST: Update AutoBST script to stop Chaos IOs before deleting FS and other fixes.(DCSG00134557)
-MR 7.14 Linux driver Read-Me file needs some corrections..(DCSG00070005)
-MR_7.14: Linux driver OS_Support_list needs an update..(DCSG00115285)
-MR7.14: Driver is using undefined macro MFI_BIG_ENDIAN for isEPD bit field.(DCSG00137916)
-Limit max device queue_depth to controller queue_depth.(DCSG00059412 (Port Of Defect DCSG00082448))

EnhancementRequests:
-Modify bst_linux.py script to load RHEL7.7 binary.(DCSG00130098)
-MR7.15: RHEL8.2 GA OS Support.(DCSG00167212)
-update dkms.conf file for UBUNTU20.04.(DCSG00080086)
-Remove NVME hole detection algorithm.(DCSG00076490)
-Add RHEL7.8 GA Support.(DCSG00129747)
-MR7.15: SLES15SP2 GM Support.(DCSG00259047)
-Citrix Hypervisor 8.1 GA support.(DCSG00062914)
-BST scripts optimization.(DCSG00073579)
-Source RPM support for RHEL8.2 and UBUNTU20.04 pre-GA OS.(DCSG00079575 (Port Of EnhancementRequest DCSG00081340))


07.713.02.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.13
Defects:
-Use RAID map for Tape devices even if FW supports JBOD sequence map.(DCSG00055167)
-Add NULL check for RAID map pointer in non RW LDIO path and fix coverity reported issues.(DCSG00033292)
-Code review found defect.(DCSG00058719)
-Improper error print message for non-secure AERO adapters.(DCSG00045253 (Port Of Defect DCSG00054761)

EnhancementRequests:
-Unique names to MSIx vectors.(DCSG00025922)
-Call kernel panic upon receive of IO with holes for NVME devices.(DCSG00049785)
-Add binary support for RHEL8.1.(DCSG00049836)
-MR7.13 : SLES12-SP5 GM Support.(DCSG00055090)
-Source RPMs shall be signed with GPG public-private key.(DCSG00056767)
-Source RPMs shall be signed with GPG public-private key.(DCSG00054345)
-Add driver support for "scsi_status" propagation to application.(DCSG00041807)
-MR Linux Driver 7.13 : Driver needs to issue all NonRW IOs to SES/vSES devices as LDIOs.(DCSG00041449)
-Use Block layer API to check SCSI device in-flight IO request.(DCSG00057168)


07.712.02.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.12

Defects:
-Remove incorrect print of Performance mode.(DCSG00002462)
-Improper error print message for non-secure AERO adapters.(DCSG00045253)
-MR7.11 Linux: Controller hangs on the second OCR.(DCSG00012579 (Port Of Defect DCSG00016290)

EnhancementRequests:
-Update queue_depth of sas and NVMe device.(DCSG00007172)
-Port upstream code to MR7.12 in-house code.(DCSG00005496)
-Remove CPU arch check to decide performance mode and rework PCI link speed detection logic.(DCSG00002646)
-Add transition_to_ready retry logic in resume path.(DCSG00008028)
-RHEL 7.7 Support for MR 7.12.(DCSG00020730)
-(DCSG00012782)
-Remove code for older unsupported kernels.(DCSG00002458)
-.(DCSG00002460)
-(DCSG00017314)
-.(Change sdev queue depth max vs optimal)


07.710.06.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.10

Defects (20)
 - Add retpoline support in source rpm and fix compilation error in sles15sp1 (SCGCQ02079110)
 - (Supported (Sea((SA(S38xx) PCI IDs. (SCGCQ01942752)
 - MR7.10: Driver logs wrong message about adapter's DMA mask (SCGCQ02012089)
 - Addressed few code review defects/comments on hybrid interrupts implementation. (SCGCQ02057600)
 - Remove support for (Sea(38xx) PCI IDs in MR driver (SCGCQ01913282)
 - MR_7.9: Linux driver fails to reboot the system when controller is in dead. (SCGCQ01936787)
 - Fix deadlock in few DCMDs timeout path due to re-acquiring of "reset_mutex" lock (SCGCQ02044603)
 - (Set VirtualDiskTgtId and devHandle appropriately when JBOD seuqence map is supported by firmware but disabled at driver devel (SCGCQ02080583)
 - MR7.9: Restrict hardware workaround for PCI register read retries for Aero/(Sea PCI IDs Only (SCGCQ01977849)
 - MR7.9, Linux driver: On PowerPC, calling disable_irq_nosync from IRQ context does not work as expected (SCGCQ01984754)
 - MR7.10_ARM:Assertion failure seen in firmware during boot on cavium ARM server (SCGCQ02035288)
 - Fixed PCI link speed detection and modified few printk debug levels (SCGCQ02102444)
 - Unwanted messages seen during source rpm/dpkg installation on Ubuntu (SCGCQ01958026)
 - Corrected opcode of MFI_CMD_TOOLBOX (SCGCQ02033111)
 - MR7.10: (SLE(S12 (SP4 driver module need to be compiled with "extern" retpoline flags (SCGCQ02034399)
 - Dev Linux B(ST script updates to (SAL-1.1902.1.3 (SCGCQ02075522)
 - MR7.9: Aero perf improvement - Change high IOPs reply queue count to 8 and reply batch count to 16 (SCGCQ01977946)
 - MR_7.10: Citrix Xenserver Readme file os support should be updated as per os matrix policy. (SCGCQ02115720)
 - Removed few debug counters from IO path (SCGCQ01942753)
 - Fixed compilation warnings due to reading non-atomic variable-"device_busy" using atomic_read API for older kernels(<3.17). (SCGCQ01965596)
 - Enhancement to add support for HO(ST_DEVICE_LI(ST DCMD in Linux driver(SCGCQ02051854 port of SCGCQ02016716)
 - Fix deadlock in few DCMDs timeout path due to re-acquiring of "reset_mutex" lock(SCGCQ02056151 port of SCGCQ02044603)
 
EnhancementRequests (19)
 - Added Aero support (SCGCQ01889127)
 - (Support added for High IOPs Reply queues(reply queues with interrupt coalescing ON) to improve Aero performance (SCGCQ01890975)
 - MR7.9: Add O(S (Support for RHEL 7.6 (SCGCQ01957415)
 - MR Aero: Driver should enable PCIe ExtTags (SCGCQ02016780)
 - Add support for Marlin(device ID- 0xd3) PCI ID. (SCGCQ01889122)
 - If any fusion register read returns all zeroes, driver will retry reading same register upto 3 times. (SCGCQ01965468)
 - Removed support for UEK kernels and (SLE(S12 (SP1 (SCGCQ02016741)
 - MR7.8 : Add rhel7.6 and sles12sp4 support (SCGCQ02069610)
 - (Support for multiple performance modes for Aero. (SCGCQ02072557)
 - (Support hybrid set of managed and non-managed vectors for 5.0 and onwards kernels (SCGCQ02018287)
 - MR7.10: Modify RPM spec file to be compatible with RHEL8 RPM framework (SCGCQ02011954) 
 - MR7.8 support for rhel8 and sles15sp1. (SCGCQ02063925)
 - MR 7.9: (SLE(S12 (SP4 O(S (Support (SCGCQ01940318)
 - Added driver support for PCI lane margining passthrough commands (SCGCQ01943619)
 - MR7.9: Add O(S (Support for OEL 7.6 (SCGCQ01966563)
 - (Supported DKM(S based source Deb/RPM for Ubuntu (SCGCQ02012043)
 - Driver should not issue fastpath IO to Region Lock Bypass queue. (SCGCQ02018278)
 - Use 32 bit atomic descriptor for Aero if firmware supports it. (SCGCQ01965225)
 - MR7.9: (Set 63-bit DMA mask in MR Linux driver (SCGCQ01981597)

07.708.05.00-1  - Moderate Impact/Low Probability of Occurrence
---------------------
MR 7.8

defects:
- FW flash is not needed for driver.(SCGCQ01593539)
- MR_7.8:Ubuntu 18.04 OS package description is mentioned as SAS 2.0.(SCGCQ01826712)
- MR7.8: Driver compilation fails on latest upstream kernel(>= v4.17), due to changes in
"queue_flag_set_unlocked" API.(SCGCQ01821588)
- MR7.8: Global SMP affinity setting is disabled incorrectly by driver under certain conditions.(SCGCQ01822883)
- MR7.8: Disable WRITE SAME commands from host for zeroout block ranges operations.(SCGCQ01823902)
- Alpha Release Version 07.708.03.00-1 - MR_LINUX_DRIVER_7.8 (38)
- MR7.8: Linux driver compilation fails on PPC (ppc64le) server(SCGCQ01861892)
- MR7.8: During probe, locking PCI config space while doing adp_reset is applicable to all fusion based
controllers.(SCGCQ01841413)
- MR7.8: Capture known OS limitations in Driver readme.(SCGCQ01888783)
- Fix deadlock in few DCMDs timeout path due to re-acquiring of "reset_mutex" lock.(SCGCQ02044603)
- Driver BST test cases need modification.(SCGCQ01664978)
- Driver fires a DCMD to incorrect Target ID’s to obtain Maximum Data transfer size (MDTS) of NVME
devices.(SCGCQ01786657 port of SCGCQ01760644)

(EnhancementRequest
- Update Linux Driver BST scripts and wrapper.(SCGCQ01529349)
- MR7.8: Enable irq poll in Linux driver to avoid CPU hard and soft lockups.(SCGCQ01571355)
- Improvement in driver debugging.(SCGCQ01753524)
- Retpoline compilation support for MR Linux drivers for Spectre_v2 vulnerability.(SCGCQ01763140)
- MR7.8: Lock access to controller's PCI config space from user space while Diag reset
operation is going on.(SCGCQ01824443)
- MR7.8: Add RHEL 6.10 Support.(SCGCQ01838376)
- MR7.8: Add SLES 15 OS Support.(SCGCQ01854853)
- MR7.8: Add Oracle Linux 6.10 OS Support.(SCGCQ01857765)
- MR7.8 : Add rhel7.6 and sles12sp4 support.(SCGCQ02069610)
- MR7.8 support for rhel8 and sles15sp1.(SCGCQ02063925)


07.707.04.00-1 - Moderate Impact/Low Probability of Occurrence
--------------------------
MR 7.7 (new)

Defects:
- Driver will use 64 bit request descriptor for sending IO to Ventura firmware.(SCGCQ01514452)
- FW flash is not needed for driver.(SCGCQ01593539)
- Modified driver prints to dump relevant FW provided values(part of controller info structure) in syslog.(SCGCQ01626839)
- Merge upstream patch "Convert timers to use timer_setup" to in-house and support timer_setup API in 4.15 kernels.(SCGCQ01586787)
- MR7.7: scsi_dma_map() is called twice in IO path.(SCGCQ01619432)
- Driver is incorrectly deciding combined reply queue mode for SAS3.0 controller(SCGCQ01633318)
- Updated driver's file- "OS_Support_list_mr7.7.txt" with CMA support enablement and retpoline compliant driver binaries.(SCGCQ01760521)
- Renamed scratchpad registers from scratchpad0 , scratchpad1 etc ... in order to align with firmware naming convention.(SCGCQ01440031)
-(SCGCQ01664978)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01440720 port of SCGCQ01430747)
- Driver should go through stream detection logic after it's finalized which path(fastpath vs non fastpath) IO will go through.(SCGCQ01483730 port of SCGCQ01468189)
- XenServer 7.3 OS support- MR 7.6.(SCGCQ01594134 port of SCGCQ01554012)
- Divert FastPath IO with Chain frame to Firmware path.(SCGCQ01598186 port of SCGCQ01593175)
- expose fw_outstanding and drv_outstanding variables to the OS level sys interface.(SCGCQ01475068 port of SCGCQ01019663)
- Driver should go through stream detection logic after it's finalized which path(fastpath vs non fastpath) IO will go through.(SCGCQ01542421 port of SCGCQ01468189)
- expose fw_outstanding and drv_outstanding variables to the OS level sys interface.(SCGCQ01542422 port of SCGCQ01019663)
- After a kill adpater, megasas_wait_for_adapter_operational waits for almost 360seconds before bailing out.(SCGCQ01619441 port of SCGCQ01615239)
- Setup IRQs only after Reply descriptors are allocated.(SCGCQ01542423 port of SCGCQ01506133)
- MR: Remove trace kernel RPMs from SUSE SLES11 SP4 driver iso images.(SCGCQ01594109 port of SCGCQ01563428)
- megasas_get_target_prop failing after OCR completed.(SCGCQ01619439 port of SCGCQ01607430)
- NVMe Task Management - Controller Reset Support (MegaRAID).(SCGCQ01592015 port of SCGCQ01545040)
- Updated OEL6_UEK and OEL7_UEK buildkit.(SCGCQ01443432 port of SCGCQ01439776)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01449786 port of SCGCQ01430747)
- Use pci_{alloc/free}_irq_vectors for >=4.12 kernels.(SCGCQ01449816 port of SCGCQ01442784)
- Setup IRQs only after Reply descriptors are allocated.(SCGCQ01514459 port of SCGCQ01506133)
- Driver will use 64 bit request descriptor for sending IO to Ventura firmware.(SCGCQ01523087 port of SCGCQ01514452)
- Increased JBOD FPIO timeout by 1 sec to workaround hardware bug which causes timeout 1 sec earlier than provided timeout value.(SCGCQ01542419 port of SCGCQ01449957)

EnhancementRequests (23)
- Use pci_{alloc/free}_irq_vectors for >=4.12 kernels.(SCGCQ01442784)
- Few officially unsupported PCI IDs are removed from MR7.7 driver code.(SCGCQ01598587)
- XenServer 7.4 OS support - MR 7.7.(SCGCQ01628129)
- Increased JBOD FPIO timeout by 1 sec to workaround hardware bug which causes timeout 1 sec earlier than provided timeout value.(SCGCQ01449957)
- Rebase inbox megaraid_sas driver to inhouse to reduce two different code base for maintenance.(SCGCQ01578030)
- MR_Aero: Create timer based thread in MR drivers to detect firmware FAULT.(SCGCQ01157766)
- Remove UpdateIoMetric and hence adapter level spinlock from IO path(SCGCQ01522127)
- Create cpu to msix table for kernel provided PCI_IRQ_AFFINITY (>=4.12 kernel).(SCGCQ01598134)
- OS driver support for Oracle Linux 7.5 - MR 7.7.(SCGCQ01586106)
- OS Driver Support for Ubuntu 18.04- MR 7.7.(SCGCQ01586128)
- Support RHEL7.5 GCA (3.10.0-862.el7.x86_64).(SCGCQ01586135)
- Early detection of faulty controller.(SCGCQ01599562)
- Change attribution language from Avago to Broadcom and update copyright end year.(SCGCQ01753095)
- Offload R5/R6 division to driver.(SCGCQ01513544)
- Update Linux Driver BST scripts and wrapper.(SCGCQ01529349)
- Marlin support is added to drivers.(SCGCQ01440724)
- Remove support for RHEL7.1, OEL7.2 and SLES12.(SCGCQ01449982)
- Optimize code around (raid context) in IO path.(SCGCQ01598187)
- Removed support of RHEL7.1, SLES12 and OEL7.2.(SCGCQ01600475)
- FW OCR Debug Mechanism - triggerSnapDump.(SCGCQ01520447)
- Set SLD bit in RAID map when "enableSLDOnAllRWIOs" is enabled.(SCGCQ01715619)
- Revert code changes related to iMR performance throttling.(SCGCQ01749962)
- Revert changes added in driver to divert FastPath IO with Chain frame.(SCGCQ01752939)


Version 07.705.04.00-5 - Moderate Impact/Low Probability of Occurrence

Defects (7)
- Provided driver workaround to reset __GFP_WAIT flag while allocating IO request frames.(SCGCQ01394892)
- Driver will use 64 bit request descriptor for sending IO to Ventura firmware.(SCGCQ01514452)
- Set DMA mask after FW is in READY state in PCI resume path of megaraid_sas driver(SCGCQ01389431)
- Fixed few dev found and coverity reported defects(SCGCQ01392652)
- Selective stream detection logic in driver(SCGCQ01392643)
- During PCI remove, set unload flag after scsi_remove_host is called.(SCGCQ01392656)
- update LD map after populate drv_map, increase wait in IOCTL, fix index in error handling, rework in refiring DCMDs.(SCGCQ01415439)
- Added support for threaded interrupts.(SCGCQ01615015 port of SCGCQ01498747)
- Driver should go through stream detection logic after it's finalized which path(fastpath vs non fastpath) IO will go through(SCGCQ01483730 port of SCGCQ01468189)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01455132 port of SCGCQ01430747)
- MR: OEL 7.4 and 6.x x86_64 RPMs do not have the correct kernel versions.(SCGCQ01611888 port of SCGCQ01607445)
- expose fw_outstanding and drv_outstanding variables to the OS level sys interface.(SCGCQ01475068 port of SCGCQ01019663)
- Updated correct supported kernel version of Ubuntu16.04 in driver's document- OS_support_list_mr7.5.txt.(SCGCQ01564604 port of SCGCQ01454090)
- Added NVME passthru support in MR linux driver.(SCGCQ01424605 port of SCGCQ01407028)
- Updated correct supported kernel version of Ubuntu16.04 in driver's document- OS_support_list_mr7.5.txt.(SCGCQ01455206 port of SCGCQ01454090)
- Added NVME passthru support in MR linux driver.(SCGCQ01455135 port of SCGCQ01407028)
- Updated OEL6_UEK and OEL7_UEK buildkit.(SCGCQ01443433 port of SCGCQ01439776)
- Setup IRQs only after Reply descriptors are allocated.(SCGCQ01514459 port of SCGCQ01506133)
- Use pci_{alloc/free}_irq_vectors for >=4.12 kernels.(SCGCQ01449816 port of SCGCQ01449816)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01449786 port of SCGCQ01430747)
- Set DMA mask after FW is in READY state in PCI resume path of megaraid_sas driver.(SCGCQ01392672 port of SCGCQ01389431)


EnhancementRequests (10)
- MR7.4: Add SLES12 SP3 OS support.(SCGCQ01396756)
- Added support for RHEL7.4.(SCGCQ01455156)
- Added driver support for OEL7.4.(SCGCQ01396747)
- Increased JBOD FPIO timeout by 1 sec to workaround hardware bug which causes timeout 1 sec earlier than provided timeout value.(SCGCQ01449957)
- Added support for threaded interrupts.(SCGCQ01498747)
- MR7.4: OS driver support for RHEL 7.4.(SCGCQ01396738)
- Added support for SLES12 SP3.(SCGCQ01455167)
- Added driver binary support for Xenserver7.2.(SCGCQ01393249)
- Remove support for RHEL7.1, OEL7.2 and SLES12.(SCGCQ01449982)
- Removed support for few OS to align with OS support matrix policy.(SCGCQ01393194)


Version 7.703.07.00- Moderate Impact/Low Probability of Occurrence
---------------------
fixes:
- Send sense buffer upper 32bits inside IOC INIT frame.(SCGCQ01315987)
- MR: On OEL 6.x/7.x with UEK kernels - megaraid_sas.conf file from the kmod rpm does not match kernel version.(SCGCQ01319368)
- pass upper 32 bits of version buffer and system information buffer to FW inside IOC INIT frame.(SCGCQ01326366)
- Workaround changes for FW MFA frame pull issue.(SCGCQ01338087)
- Log dmesg if IOC INIT fails in IOMMU and RDPQ enabled enviornment for user information only.(SCGCQ01338097)
- Validated if any of DMA buffers pool which should be in same 4GB region does not cross 4GB boundary.(SCGCQ01338372)
- Memset to zero for MFI command frame for IOC INIT and use lower_32_bits() macro to get lower 32bits of DMA address passed to FW.(SCGCQ01341287)
- Removed Crusader ID(device ID- 0x0015) from supported PCI IDs of MR7.2 linux driver.(SCGCQ01350963)
- MR7.3: Code review defect - ioc_init_frame not freed during kernel module unload.(SCGCQ01384694)
- MR7.2: In megasas_issue_tm() SMID needs to be used for Task abort case only.(SCGCQ01315252)
- Incorrect processing of IOCTL frames for SMP/STP commands.(SCGCQ01383823)
- Set cmd_status inside DCMD/IO/header frame to MFI_STAT_OK to wake up all pended IOCTLs.(SCGCQ01298582)
- Removed print "Failed from megasas_complete_cmd" from PD CFQ sequence DCMD completion path.(SCGCQ01321565)
- Do not switch DMA mask to meet same 4gb requirement. IOMMU does not work well with such DMA mask switch.(SCGCQ01342578)
- Allocated MFI frame size and the size of MPT chain frame(Where MFI frame resides for MFI MPT passthru commands) should match.(SCGCQ01342650)
- Minimum possible value for module parameter- resetwaittime should be 1 secs instead of 0 secs.(SCGCQ01344137)
- Set DMA mask after FW is in READY state in PCI resume path of megaraid_sas driver.(SCGCQ01389431)
- MR7.3: Data miscompare found with WB secure VD RAID 1 with LSA sending IOCTLs in parallel.(SCGCQ01378684)
- Set cmd_status inside DCMD/IO/header frame to MFI_STAT_OK to wake up all pended IOCTLs.(SCGCQ01381770 port of SCGCQ01298582)
- MR: On OEL 6.x/7.x with UEK kernels - megaraid_sas.conf file from the kmod rpm does not match kernel version.(SCGCQ01320324 port of SCGCQ01319368)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01455132 port of SCGCQ01430747)
- Updated correct supported kernel version of Ubuntu16.04 in driver's document- OS_support_list_mr7.5.txt.(SCGCQ01455206 port of SCGCQ01454090)
- Added NVME passthru support in MR linux driver.(SCGCQ01455135 port of SCGCQ01407028)
- Updated OEL6_UEK and OEL7_UEK buildkit.(SCGCQ01443433 port of SCGCQ01439776)
- Minimum possible value for module parameter- resetwaittime should be 1 secs instead of 0 secs.(SCGCQ01344142 port of SCGCQ01344137)


EnhancementRequests:
- Added support for 64bit DMA mask for invader.(SCGCQ01294199)
- MR7.3: add support for Citrix XenServer 7.1 OS.(SCGCQ01257971)
- Send current time to FW during IOC init.(SCGCQ01307072)
- Added support for RHEL7.4.(SCGCQ01455156)
- MR7.3: add support for OEL 6.9.(SCGCQ01289005)
- Added support for threaded interrupts.(SCGCQ01498747)
- Added support for 64bit DMA.(SCGCQ01301940)
- Added support for SLES12 SP3.(SCGCQ01455167)



Version 7.702.06.00- Moderate Impact/Low Probability of Occurrence
---------------------
Defects (47)
 - Reset MPT frame field cmd_completed while retrurning it back to free pool.(SCGCQ01176530)
 - Optimized R1 FP write code.(SCGCQ01191077)
 - Before populating driver RAID map copy memset drv_map to zero and ldTgtIdtoLd array to 0xff(SCGCQ01204087)
 - Initialize stream detection array properly.(SCGCQ01204096)
 - On SPARC/Big endian host, need to convert peerSMID to little endian to CPU before accessing(SCGCQ01216698)
 - Fixed coverity reported issues and changed name of few functions.(SCGCQ01219231)
 - Don't set tm_capable for JBDO when PD CFG SEQ map is not available(SCGCQ01226222)
 - Remove local defination FALSE/TRUE and use OS provided false/true.(SCGCQ01256130)
 - Used vmalloc for crash dump buffers and driver's local RAID maps(SCGCQ01270059)
 - Reduce size of fusion_context allocation during driver load by moving load_balance_info array out, and try vmalloc if kmalloc fails.(SCGCQ01183280)
 - Flooding of messages- "BRCM: IO does not end on page boundary; sge_len" while running RAW IOs.(SCGCQ01189815)
 - Fixed data corruption by asking OS not to do merging of IOs to avoid SGE holes(SCGCQ01231229)
 - Code review defect: create separate function for allocating RAID maps(SCGCQ01282924)
 - Removed Crusader ID(device ID- 0x0015) from supported PCI IDs of MR7.2 linux driver(SCGCQ01350963)
 - Updated OS to send page aligned SGEs by calling blk_queue_virt_boundary(SCGCQ01206279)
 - Use vmalloc followed by memset to zero instead of vzalloc in driver code.(SCGCQ01206316)
 - MR_ValidateMapInfo issue on bigendian platform (In some case Detect Ghost VDs)(SCGCQ01213952)
 - Fixed code review defects(SCGCQ01254323)
 - Removed code inside macros VD_EXT_DEBUG, SPAN_DEBUG and enahnce prints in OCR path(SCGCQ01270056)
 - FW fault happens as driver wrongly fill numSGE=0.(SCGCQ01274103)
 - Code optimization and enhanced prints for debugging(SCGCQ01224881)
 - Remove unsupported PCI Device IDs from the driver code(SCGCQ01234256)
 
 - Resolved conflict of PCI device ID-0x0015(SCGCQ01254317)
 - MR7.2: In megasas_issue_tm() SMID needs to be used for Task abort case only(SCGCQ01315252)
 - Save interfaceType for each sysPDs inside SCSI device's private data field which will persists until sysPD is removed/deleted.(SCGCQ01216464)
 - Code Optimization and enhanced prints(SCGCQ01223300)
 
 - MR 7.1: Linux OS crash when powering off enclosure during I/O(SCGCQ01229442)
 - Return pending IOs with status DID_REQUEUE instead of DID_RESET to SCSU layer before doing OCR(SCGCQ01231846)
 - MR7.2: Port changes from upstream to make in-house MR 7.2 code to be consistent with upstream code(SCGCQ01282321)
 - Add print for partially copied SCSI IO and fix few endianness issues(SCGCQ01224305)
 - Linux Driver 07.700.23.00/Getting megaraid_sas prints during startup of OS(SCGCQ01255074)
 - aen class range check to avoid kernel panic(SCGCQ01256126)
 - Corrected bitmap macros inside struct RAID_CONTEXT35(SCGCQ01269453)
 - Set cmd_status inside DCMD/IO/header frame to MFI_STAT_OK to wake up all pended IOCTLs.(SCGCQ01298582)
 - Fix few dev found issues(SCGCQ01226224)
 - On OEL SPARC (Big Endian), Linux MR 7.1 driver loading fails to initialize Ventura which has RDPQ support enabled(SCGCQ01229897)
 - Fixed few code collab defects/comments(SCGCQ01202237)
 - Remove throttle IOs prints in IO path and add sysfs parameter to reflect number of R1 FP writes(SCGCQ01204099)
 - Ventura MR-7.0.1 RHEL 7.2 driver: ERR messages when installing driver 7.700.20.00(SCGCQ01222990)
 - Use do_div() kernel API to do modulo operation of 64 bit dividend and 32bit divisor .(SCGCQ01243263)
 - megasas_complete_cmd_dpc_fusion() will be called with 1 sec delay inside function megasas_wait_for_outstanding_fusion(SCGCQ01256116)
 - Allocated MFI frame size and the size of MPT chain frame(Where MFI frame resides for MFI MPT passthru commands) should match(SCGCQ01342650)

EnhancementRequests (17)
 - Big endian architecture is now support for Ventura generation of MR HBA.(SCGCQ01256016)
 - Fixed the problem of sync_irq not being called when MSI-x are disabled.(SCGCQ01206307)
 - Port changes from MR7.0 and MR6.13 critical fixes to MR7.1(SCGCQ01167939)
 - In megasas_build_ldio_fusion, code to set controller CPU affinity can be optimized(SCGCQ01216486)
 - Set device queue depth same as controller's can_queue for SCSI MQ mode(SCGCQ01271569)
 - Add SLES 11 32-bit build kit support to Ventura MR.(SCGCQ01214721)
 - Ported fixes from MR 6.13 to MR 7.1(SCGCQ01222522)
 - Added support for RHEL7.3(SCGCQ01224300)
 - Support SPARC/PPC/ARM (Big/Little Endian). Fix Endianess issue in MR Ventura driver.(SCGCQ01183275)
 - Added DCMD interface to read target properties for SCSI device(VDs and JBODs both)(SCGCQ01220142)
 - Added KMOD RPM support for OEL7.3 UEK.(SCGCQ01227476)
 - R1 Write IOPs improvement(SCGCQ01213232)
 - Extra code for bug in A0 ventura is removed. Optimized Descriptor write as Ventura required 32 bit in major IO Path operation.(SCGCQ01215347)
 - Remove Crusader device support from driver(SCGCQ01259175)
 - Don't re-issue Reset on the way back OCR(SCGCQ01215089)
 - Rework start_vm_build script used for VBAS build and new build infrastructure for DKMS RPMs(SCGCQ01261800)
-

Version 7.700.26.00- Moderate Impact/Low Probability of Occurrence
---------------------
Enhancement:
- Added support for ThinkSystem HBA and RAID.


Version 6.812.08.00 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes:
- Modified not to send outstanding IOs back to SML with DID_RESET host_byte but return IOs back with host_byte DID_REQUEUE before doing OCR. (SCGCQ01278656 Port Of Defect SCGCQ01231846)

Enhancement
- Added support for SLES 12.2


Version 6.812.07.00 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes
 - Changed timeout value for DCMDs get_bios_data and get_pd_info 180 seconds to keep it aligned with other DCMDs' timeout value. (SCGCQ00884247)
 - Do not allow MFI frame to be freed from DCMD fire context when already an OCR is in progress. (SCGCQ00879190)
 - Fixed an issue where driver always worked in non RDPQ mode even the running firmware did not support RDPQ. (SCGCQ00872542)
 - Moved SCSI layer interaction code out of reset_mutex in AEN thread to prevent deadlock around reset_mutex. (SCGCQ00868731)
 - Convert supported JBOD count value returned by firmware in CPU format and then use the same value for further validation (SCGCQ00837088)
 - Fixed an issue where unevenSpan configuration of R1 would not have proper load balancing for FP READ. SCGCQ00646224
 - Added timeout value for wait_event. (SCGCQ00249742)
 - Enabled hostlockless flag of SCSI host for RHEL6 and clones for async IO submission from SCSI mid layer. (SCGCQ00884242)
 - Fixed an issue where double freeing of MFI frame in case of MFI IO timeout in polled mode could occur. (SCGCQ00837932)
 - Added synchronization between OCR thread and AEN thread, so that there should not be any PCI write from AEN thread during OCR (SCGCQ00836410)
 - Added IO timeout value for SCSI management commands for JBOD. (SCGCQ00750452)
 - Fixed a JBOD performance issue due to incorrect MSI-x index set in request desc. (SCGCQ00619694)
 - Changed state machine of firmware crash dump collection to prevent file system on VD being set to Read-only mode after ECC error injection. (SCGCQ00608705)
 - Fixed an issue where incorrect messages such as LSI SAS2.0 were printed for MR driver. (SCGCQ00298201_
 - Fixed an issue where the driver sent an incorrect region type "REGION_LOCK_EXCLUSIVE" set to FW for RAID level >=5
 - Changed error handling for DCMD failure cases to allow graceful exit for not fatal errors. (SCGCQ00868661)
 - Free task management frame after dumping the task management reply frame data to ensure that TM reply frame will have valid data returned by firmware. (SCGCQ00860038)
 - Release reset_mutex inside OCR function, if adapter is already killed to prevent a kernel panic. (SCGCQ00857740)
 - Increased timeout to 180 seconds for flush cache and shutdown controller DCMDs to prevent kernel panic when DCMDs fired during driver's shutdown. (SCGCQ00841491)
 - Fixed an issue where traversed LDs at multiple places up to maximum 256 were limited to 64. (SCGCQ00652795)
  - Fixed an issue where the driver crashed when msix_disable=1 was passed to the boot time parameter. (SCGCQ00383508)
 - Fixed an issue where kernel panic seen while deleting VD and background IOs running. (SCGCQ00803468)
 - Fixed an issue where the driver was not sending DCMD- MR_DCMD_CTRL_SET_CRASH_DUMP_PARAMS after OCR. (SCGCQ00601138)
 - Fixed an issue where the kernel panicked inside PCI subsystem because of IRQs not freed before disabling MSI-X interrupts (SCGCQ00827403)
 - Disabled SED drive JBOD support. (SCGCQ00751296)
 - Fixed multiple OCRs triggering hits Exception Core issue (SCGCQ00707592)
- Fixed an issue where the firmware faulted due to invalid regionlock Flags set by Driver. (SCGCQ00796461)
- Fixed an issue where subsequent reads of state value from hardware resulted different values and could lead to a timeout in and a non working adapter. (SCGCQ00709216)
- Fixed an issue where Offline VD caused boot hangs in SLES 11 (SCGCQ00284564)
 - Disabled SPAN_DEBUG and set get_arm_from_strip to print if firmware supports UnevenSpan. (SCGCQ00365846)
 - Added check to validate ldcount exposed in firmware RAID map for legacy firmware.  If ldcount is more than 64, fail RAID map validation. (SCGCQ00820349)
 - Fixed an issue where the Linux kernel crashed when AEN and LD Sync commands were issued frequently. (SCGCQ00712031)
 - Fixed an issue where duplicate disk(s) were seen on controller after loading Linux driver during OS installation, (SCGCQ00568992)
 - Fixed an issue where kernel panic could occur at driver load time on 3.0 kernels (i.e. SLES11 SP2, SLES11SP3). (SCGCQ00561505)
 - Changed driver to return SCSI command back to mid layer if the controller has any critical hardware errors. SCGCQ00362023
 - Fixed an issue where the driver did not do Load balance for R1 READ due to wrong stats counters. (SCGCQ00677516 Port of Defect - SCGCQ00674872)
 - Fixed potential duplicate IOCinit frames being fired by VMware5 VF driver during OCR. (SCGCQ00571967 PORT OF SCGCQ00571679)
 - Fixed OS crash issue on SCSI IO timeout (SCGCQ00631210 PORT OF SCGCQ00625137)
 -Fixed an issue where the kernel panicked due to MFI/MPT pass-through command timeout and later finished from Interrupt context. (SCGCQ00307867 PORT OF - SCGCQ00302080)
 - Fixed an issue where megasas_poll_wait_aen was cleared before poll syscall returns causing to lose events (SCGCQ00575192 PORT OF SCGCQ00574787)
 -Fixed an issue where data corruption observed on JBODs while running IOs with 32k block size. (SCGCQ00530992 PORT OF SCGCQ00523780)
 - Fixed MPC kernel panic during chassis power cycle if AEN completes and detach is called before event workqueue runs. (SCGCQ00647390 PORT OF SCGCQ00645836)
 - Fixed an issue where kernel crashed in some cases, where megaraid_sas driver is loaded but controller is not present. (SCGCQ00282968 PORT OF SCGCQ00282067)


Enhancements:  
 - Set queue depth for syspD based on interface type (SCGCQ00879700)
 - Updated module Meta data (module description and module author) with Avago replacing LSI. (SCGCQ00801961)
 - Set OS provided timeout value for sysPD non read-write IOs (SCGCQ00764795)
 - Performance tuning for SMP affinity is implemented for distros's which support irq_set_affinity_hint API. (SCGCQ00623697)
 - Optimized OCR path to enable interrupt and make HBA OPERATIONAL after driver has fired LD_MAP_GET_INFO DCMD. (SCGCQ00768402)
 - Added module parameter to turn on/off SMP affinity code. (SCGCQ00666706)
 - Driver will do load balance for N Drive Raid 1 volumes. (SCGCQ00634064)
 -Functionality in driver is added to differentiate between iMR and MR at firmware initialization time. (SCGCQ00361244)
 - Uneven Span support added in Driver. (SCGCQ00319104)
 - Driver code is updated such way that it can work for any block size drive, if the rest of the system has proper support for the same. (SCGCQ00259244)
 - Implemented online controller reset if controller is not responding at driver load time. (SCGCQ00820389)
 - Added SCSI residual bytes support to the megaraid_sas Linux driver (SCGCQ00347089)
 - Use sequence number for JBOD FastPath I/Os to eliminate command block after drive replacement (SCGCQ00806534)
 - Big endian architecture support added for MR Linux driver (SCGCQ00526911)
 -  Driver support is added for 3108 C0 chip combine reply queue ON (SCGCQ00354586)
 - Added support 240 VD feature (SCGCQ00622703)
 - Added Firmware crash dump collection support (SCGCQ00550369)
 - Added support for large I/O 1MB transfer size (SCGCQ00816313)
 - Changed the max sg table size to 64. Old setting was 70 (SCGCQ00653992)
 - Added driver support for task management for Jbod or VD (tmCapable) (SCGCQ00854635)
 - Added support for SED JBOD in MR Linux driver (SCGCQ00711555)
 - Changed code to complete IOCtls posted just before a kill adapter so user space applications do not hang. (SCGCQ00759916)


Version 6.810.09.00 - Moderate Impact/Low Probability of Occurrence
---------------------
 Fixes:

 - Fixed an issue where deadlock may occur when the Automatic Event Notification thread runs in parallel with error handler thread (SCGCQ00911332, Port of SCGCQ00868731)

 - Fixed an issue where driver will operated in RDPQ mode regardless of whether firmware has advertised support or not (SCGCQ00872542)

 - Fixed an issue where system may reset with error "BUG: unable to handle kernel NULL pointer dereference at 00000000000000d0" preceded by error "megasas: target reset FAILED!!" (SCGCQ00875223)

 - Fixed an issue where driver MFI frames could be freed twice (SCGCQ00879190)

 - Fixed an issue where some out-of-band commands had different timeouts than others (SCGCQ00884247)

 - Fixed an issue where performance was lower on async IO submissions from the SCSI mid layer (SCGCQ00884242)

 - Fixed an issue where a kernel panic may occur if the system is reset or fail to reboot (SCGCQ00859634, Port of SCGCQ00857740)

 - Fixed an issue where Task Management frames were not being dumped after the Tast Management Reply frame data (SCGCQ00860038)

 - Fixed an issue where a fatal error may occur when an out-of-band command times out during an Online Controller Reset (SCGCQ00882011, Port of SCGCQ00868661)

 - Fixed an issue where kernel may hang when many commands are timing out or many Automatic Event Notifications are being processed (SCGCQ00857245)

 - Fixed an issue where megaraid_sas module was not being included inside initrd/initramfs (SCGCQ00880965)

 - Fixed an issue where kernel may panic if driver does not setup IRQs for non-MSI-x interrupt mode (SCGCQ00870263, Port of SCGCQ00867873)

 - Fixed an issue where driver return code is based on command completion rather than command return code (SCGCQ00856103, Port of SCGCQ00856089)

 - Fixed an issue where Tape drives may not be detected by the Operating System (SCGCQ00914385, Port of SCGCQ00911702)

 - Fixed an issue where max_sectors per IO request may be set to more than firmware can handle (SCGCQ00917992, Port of SCGCQ00917399)
 
- Fixed an issue where an IERR may occurr on heavy IO with Failover (SCGCQ00864111, Port of SCGCQ00736612)
 
 
Enhancements:

 - Enhanced queue depths in driver for physical disks based on interface type (SCGCQ00879700)

 - Improved naming of internal functions (SCGCQ00866064)

 - Updated module parameter "rdpq_enable" default to "1" (enable RQPQ mode) (SCGCQ00871565)

 - Enhanced reply queue to support queue depth greater than 1K (SCGCQ00853521)

 - Added feature for driver to support Task Management for JBOD and Virtual Drives (SCGCQ00854635)

 - Added module parameter to disable 1M IO support and set default to enable 1M IO support (SCGCQ00911362)

 - Enhanced tasklet initialization so it would occur before setting up IRQs (SCGCQ00914393, Port of SCGCQ00911709)

 - Simplified HB handling for SR-IOV (SCGCQ00864113, Port of SCGCQ00700580)

 - Enhanced driver to update Online Controller Reset capability when it changes (SCGCQ00914389, Port of SCGCQ00908352)

 - Added feature to print Critical, Fatal and Dead firmware events into system logs (SCGCQ00868723, SCGCQ00882010, Port of SCGCQ00866176)

 - Enhanced HB handling to align with behavior on other Operating Systems (SCGCQ00864117, Port of SCGCQ00707323)

 - Removed excess dead code (SCGCQ00850012)

Version 6.808.16.00 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes:
- Fixed an issue where a deadlock may occur around reset_mutex when Automatic Event Notification threads run in parallel with error handlers - (SCGCQ00911332, Port of SCGCQ00868731)
- Fixed an issue where scanning of Tape drives does not occur depending on whether the drive state is set to systemPD or not - (SCGCQ00914385, Port of SCGCQ00911702)
- Fixed an issue where max_sectors may be set larger than what firmware can support - (SCGCQ00917992, Port of SCGCQ00917399)
- Fixed an issue where kernel may panic due to driver not setting up IRQs for non MSI-x interrupt mode - (SCGCQ00870263, Port of SCGCQ00867873)
- Fixed an issue where driver may halt firmware due to improper error handling for DCMD failure cases - (SCGCQ00882011, Port of SCGCQ00868661)
- Fixed an issue where driver may hang kernel due to deadlock - (SCGCQ00857245)
- Fixed an issue where system may crash due to timeout for flushing cache and shutting down controller DCMDs was not long enough - (SCGCQ00841491)
- Fixed an issue where deadlock may occur between Online Controller Reset and Automatic Event Notification processing function - (SCGCQ00846933)
- Fixed an issue where PCI writes from Automatic Event Notification thread were occurring during Online Controller Reset - (SCGCQ00836410)
- Fixed an issue where MFI frames linked list may corrupt due to double-freeing of frame in the case of an MFI IO timeout - (SCGCQ00837932)
- Fixed an issue where kernel may panic inside PCI subsystem due to IRQs not freed before disabling MSI-X interrupts - (SCGCQ00827403)
- Fixed an issue where ldcount was not validated for non-240VD firmware - (SCGCQ00820349)
- Fixed an issue where a command block would occur for JBODs with FastPath IOs after a drive is replaced - (SCGCQ00806534)
- Fixed an issue where 1MB IO support was not supported controller-wide - (SCGCQ00816313)

Enhancements:
- Set DMA alignment to 8 bytes for PI-enabled VDs - (SCGCQ00928796, Port of SCGCQ00928176)
- Added a parameter to support disabling 1MB IO support - (SCGCQ00911362)
- Added support for printing Critical, Fatal and Dead Firmware events into system logs - (SCGCQ00882010, Port of SCGCQ00866176)
- Added support for driver to perform an Online Controller Reset at driver load time if the controller is not responding - (SCGCQ00820389)

Version 6.808.14.00 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes
- Fixed an issue where controller may reset or "MonTask: line 1276" error will occur with JBOD present (SCGCQ00837088)
- Fixed a performance issue on RAID1 with 256k IO size (SCGCQ00674872)
- Fixed a performance issue on RAID1 reads with FastPath enabled (SCGCQ00646224)
- Fixed an issue where an Online Controller Reset may take an unusually lon time (SCGCQ00420374)
- Fixed an issue where a controller firmware crash may not be recognized by driver (SCGCQ00249742)
- Fixed an issue where an MFI frame may be freed twice on MFI command timeout (SCGCQ00837932)
- Fixed an issue where the firmware may fault in an Automatic Event Notification fires during an Online Controller Reset before the chip is in READY state (SCGCQ00836410)
- Fixed an issue where there was no IO timeout value for SCSI management commands for Secure JBOD (SCGCQ00750452)
- Fixed a performance issue on SSDs in JBOD mode (SCGCQ00619694)
- Fixed an issue where file system on a VD can go to read-only on ECC error detection (SCGCQ00608705)
- Fixed an issue where disks may not be found during installation after loading the driver (SCGCQ00299643)
- Fixed an issue where a kernel panic may occur when cable pulled during system reboot (SCGCQ00841491)
- Fixed an issue where 240VD support was not fully implemented (SCGCQ00652795)
- Fixed an issue where the driver may crash if msix_disable=1 is passed to kernel as boot parameter (SCGCQ00383508)
- Fixed an issue where IO errors may occur when connected to a Tape drive (SCGCQ00399947)
- Fixed an issue where kernel may hang due to megaraid_sas driver deadlock (SCGCQ00857245)
- Fixed an issue where kernel may panic when deleting VD and background IO is occurring (SCGCQ00803468)
- Fixed an issue where crash dump may be disabled after an Online Controller Reset (SCGCQ00601138)
- Fixed an issue in 32bit OSs where driver may not load on boot (SCGCQ00362423)
- Fixed an issue where deadlock may occur (SCGCQ00846933)
- Fixed an issue where a kernel panic may occur because IRQs are not freed before disabling MSI-X interrupts (SCGCQ00827403)
- Fixed an issue where multiple Online Controller Resets can trigger a Core Exception (SCGCQ00707592)
- Fixed an issue where crash dump may not be performed properly (SCGCQ00593374)
- Fixed an issue where firmware may fault with CacheCade (SCGCQ00796461)
- Fixed an issue where adapter may hang (SCGCQ00709216)
- Fixed an issue where an offline VD may cause boot hangs (SCGCQ00284564)
- Fixed an issue where kernel may panic (SCGCQ00820349)
- Fixed an issue where kernel may crash in megaraid_sas driver with CacheCade if there are many Automatic Event Notifications and LD sync operations occurring (SCGCQ00712031)
- Fixed an issue where system may hang with CacheCade (SCGCQ00687881)
- Fixed an issue where the same disk may show multiple times in OS (SCGCQ00568992)
- Fixed an issue where kernel may panic on Linux kernels version 3.0 or greater (SCGCQ00561505)
- Fixed an issue where invalid IO statistics may be provided if driver supports more than just 512b sector drives (SCGCQ00282615)
- Fixed an issue where driver fails to reboot system due to outstanding IOs in SCSI mid-layer when controller is in error state (SCGCQ00362023)

Enhancements
- Added ability for JBOD IOs going via firmware path to use timeout value provided by OS (SCGCQ00764795)
- Added a retry of IO commands as LDIO if raid map sync is failed with MFI_STAT_CONFIG_SEQ_MISMATCH (SCGCQ00712510)
- Added support for 4k sector drives if the system supports it (SCGCQ00259244)
- Added support for driver to perform an Online Controller Reset if the controller is not responding (SCGCQ00820389)
- Fixed an issue where system may hang on S3 resume (SCGCQ00758933)
- Added a feature to prevent command block with FastPath after JBOD drive replacement (SCGCQ00806534)
- Enhanced 1MB IO support (SCGCQ00816313)
- Added support for "megaraid_sas.disable_ext_io=1" boot parameter to disable 1M IO support (SCGCQ00911362)
- Added support for Secure JBOD (SCGCQ00711555, SCGCQ00753765)
- Fixed an issue where user space applications may hang if IOCtl is sent prior a kill adapter issued (SCGCQ00759916)
- Fixed an issue where OS may crash on a SCSI IO timeout (SCGCQ00631210)
- Fixed an issue where system may fail to reboot or will kernel panic on init 6 if controller has faulted (SCGCQ00859634)
- Fixed an issue where firmware may fault (SCGCQ00702536)
- Fixed an issue where controller may crash during system power cycle (SCGCQ00647390)
- Fixed an issue where kernel may crash when megaraid_sas driver is loaded but no MegaRAID controllers are present (SCGCQ00282968)



Version 6.806.09.00 - New Function Only/No fixes
-------------------





Lenovo Data Center Group Linux OS Support Home Page
linux.lenovo.com

© 2018-2021 Lenovo. All rights reserved

LSI Storage Authority Software (For Linux)



LSI Storage Authority Software

Supported controllers:
ThinkSystem RAID 530-8i PCIe 12Gb Adapter  (7Y37A01082)
ThinkSystem RAID 530-4i Flex Adapter       (7M17A03932)
ThinkSystem RAID 530-4i Flex Adapter       (7M27A03918)
ThinkSystem RAID 530-8i Dense Adapter      (SD530 RAID)
ThinkSystem RAID 530-16i PCIe 12Gb Adapter (4Y37A09727)
ThinkSystem RAID 940-8i 4GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09728
ThinkSystem RAID 940-8i 8GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09729
ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09730
ThinkSystem RAID 940-32i 8GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09733
ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Internal Adapter for 4Y37A09735
ThinkSystem RAID 730-8i 1GB Cache PCIe 12Gb Adapter  (7Y37A01083)
ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter  (4Y37A09722)
ThinkSystem RAID 930-8i 2GB Flash PCIe 12Gb Adapter  (7Y37A01084)
ThinkSystem RAID 930-16i 4GB Flash PCIe 12Gb Adapter (7Y37A01085)
ThinkSystem RAID 930-24i 4GB Flash PCIe 12Gb Adapter (7Y37A01086)
ThinkSystem RAID 930-8e 4GB Flash PCIe 12Gb Adapter  (7Y37A01087)
ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M17A03933)
ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M27A03917)
ThinkSystem  RAID 930-16i 8GB Flash PCIe 12Gb Adapter(4Y37A09721)
ServeRAID M1210 SAS/SATA Controller    (00JY194)
ServeRAID M1215 SAS/SATA Controller    (46C9114)
LSI SAS3004 RAID                       (NA-SAS3004-B)
LSI SAS3004 RAID                       (NA-SAS3004-N)
ServeRAID M5210 SAS/SATA Controller    (46C9110)
ServeRAID M5225-2GB SAS/SATA Controller(00AE938)
ServeRAID M5215 with 2GB Flash Enablement Flex System x240 M5   (00JX142)
ServeRAID M5210e SAS/SATA Controller   (46C9117CTO)
ThinkSystem 430-8i SAS/SATA 12Gb HBA   (7Y37A01088)
ThinkSystem 430-16i SAS/SATA 12Gb HBA  (7Y37A01089)
ThinkSystem 430-8e SAS/SATA 12Gb HBA   (7Y37A01090)
ThinkSystem 430-16e SAS/SATA 12Gb HBA  (7Y37A01091)
ThinkSystem 430-8i SAS/SATA 12Gb Dense HBA  (NA-StarkSASHBA)
ThinkSystem 440-16e SAS/SATA PCIe Gen4 12Gb HBA for 4Y37A09724
ThinkSystem 440-16i SAS/SATA PCIe Gen4 12Gb Internal HBA for 4Y37A09725
N2215 SAS/SATA HBA   (47C8675)
N2225 SAS/SATA HBA   (00AE912)
N2226 SAS/SATA HBA   (00AE916)

Support OS:
            - SLES 12 SP3, SLES 12 SP4, SLES 12 SP5, 
			- SLES 15 SP1, SLES 15 SP2, 
			- Ubuntu 18.04 LTS, Ubuntu 18.04.5, 
            - RHEL 7.7,7.8,7.9
			- RHEL 8.1/8.2/8.3
            - ESXi 6.7 U1/U2/U3, ESXi 7.0, ESXi 7.0 U1.
			
007.017.014.000 - Moderate Impact
---------------

Defects:
-WG: Enclosure connector info in PD properties shown "C0 & C0" instead of "C0 & C1".(DCSG00775146
-WG: Logging in to manage server page and clicking on VMware server for login results in VMware login page refresh indefinitely.(DCSG00397834
-WG: Snapdump not getting downloaded with ARM MR 7.17 LSA.(DCSG00653578
-Invalid Enclosure logical ID is displayed is LSA for enclosure connected to Hialeah 8e controller..(DCSG00967815
-LSA MR 7.17: Modifying VD size is not getting updated , if the VD size is more than the current VD size..(DCSG00718530
-WG: LSA service does not start automatically on reboot on OpenEuler.(DCSG00648374
-HBA not listed with index order under Server Profile.(DCSG00418634
-Remote Server Health status without controller is not proper.(DCSG00528112
-WG: RWC3 Linux supports obsolete SHA1-based ciphersuites.(DCSG00500737
-Ventura_LSA_7.17: Under change behavior mode, "Change " button is enabled even though configuration parameter in unchecked.(DCSG00706331
-LSA : OLH shows lane speed values as Unknown, 2.5GT/s, 5GT/s, 8GT/s for Manage PCIe Storage Interface instead of showing 2.5GT/s, 5GT/s, 8GT/s & 16GT/s.(DCSG00971355
-LSA does not launch on ARM Open Euler : 007.017.008.000 ARM build.(DCSG00905358
-LSA service is stopped, after LWM (option4) installation in Ubuntu 20.04 arm system..(DCSG00506960
-Fixed: Added interface check for appropriate mix policy.(DCSG00706336
-behavior mode values is not being set properly.(DCSG00426348
-change button is not enabled for Behavior params change.(DCSG00426709
-WG: DLL files packaged in monitor folder of ARM LSA installation.(DCSG00706354
-Linux, RHEL 8.3 - Blank screen shown on launching latest LSA.(DCSG00777144
-LSA MR 7.17: Make JBOD option is available for all the UGOOD PDs, even though one of the PD is in drive clear process..(DCSG00775455
-Login page help link is showing blank.(DCSG00548034
-Fixed: updated Build script to change permissions of different file types.(DCSG00776044
-LSA is not allowing user to create more than 2 VDs.(DCSG00726030
-Handle the new event LD_ERASE_POTENTIAL_LEAKAGE in client.(DCSG00776413
-Fixed: enclosure state is to be shown need attention when it is in fault state.(DCSG00965622
-Ventura_LSA_7.17: LSA still displays background processes of VDs(VD init) post clear config from LSA.(DCSG00644476
-Ventura_LSA_7.17: LSA crashes on creating 64th VD.(DCSG00708134
-Warning removal as part of new gcc upgrade..(DCSG00757533
-Fixed: Changing Resource type displays recover option.(DCSG00411317
-Ventura_LSA_7.17: Event ID: 633 is generated on changing VD policy when expansion is in progress.(DCSG00650740
-LSA MR 7.17: LSA has older version of LSA_Lib_Utils packaged..(DCSG00397682
-WG: Power supply details are not shown on clicking "No of Power Supplies" in enclosure properties.(DCSG00544568
-LSA MR 7.17 : When partially degraded VD erase is in progress, Erase option is available in Elements Action instead of Stop Erase.(DCSG00758642
-Fixed: Added security flags to make file to build secure LSA binaries.(DCSG00813569
-Legacy:LSA MR 7.17: Upon clicking on the hostname(administrator/root )drop down for the second time, Remote Server discovery option appears twice..(DCSG00396896
-Fixed: Added security flags to LSA Makefile.(DCSG00814604
-WG: VMware user able to download LSA logs of gateway.(DCSG00384359
-Fixed: added directory wise permission while creating corpus.(DCSG00543670
-WG: Server ID cookie generated after login has "httponly", "secure" and "sameSite" fields empty for RWC3 installation.(DCSG00547995
-LSA Client WG: Power supply details are not shown on clicking "No of Power Supplies" in enclosure properties.(DCSG00549353
-LSAServer - WG: Redhat OS icon shown for OpenEuler OS in remote discovery page and Manual discovery page.(DCSG00735182
-WG: Redhat OS icon shown for OpenEuler OS in remote discovery page and Manual discovery page.(DCSG00652676
-Ventura_LSAMR_7.17:VD initialization progress is displayed on triggering VD expansion..(DCSG00776513
-WG 7.17 PA2: error token 009" seen when LSA downgrade is performed from 7.17 PA2 to 7.16 RC build and complete LSA uninstallation is not successful.(DCSG00434242
-Ventura_LSAMR_7.17: Background process displays previous status information post clear config.(DCSG00830097
-WG: LSA allows providing same Busy port to both Webserver and LSA port, ultimately LSA service fails to start.(DCSG00556924
-LSA MR 7.17: In RLM page After applying/clearing filter, Add Physical drive tab is enabled even though no drives are selected..(DCSG00649177
-LSA shows stale data and failed to refresh topology until LSA service restart.(DCSG00477447 (Port Of Defect DCSG00708193)
-Fixed: state-change isn't updating state of the PD incase of bad to good.(DCSG00834219 (Port Of Defect DCSG00916906)
-LSA : While updating UEFI for 440-16e (Aero-IT), "Image update failed" message is coming and next time it passes.(DCSG00935787 (Port Of Defect DCSG00937166)
-LSA Common: Stale folders still persist in html folder.(DCSG00388225 (Port Of Defect DCSG00394666)
-Fixed: Limit R1 from R6 migration, show when applicable.(DCSG00776529 (Port Of Defect DCSG00960423)
-Fixed: modify virtual drive to show appropriate allowed operation values.(DCSG00433726 (Port Of Defect DCSG00518957)
-WG: Server ID cookie generated after login has "httponly", "secure" and "sameSite" fields empty for RWC3 installation.(DCSG00547995 (Port Of Defect DCSG00654119)
-LSA : PDs are not listing properly after pull/push from enclosure/Backplane.(DCSG00916164 (Port Of Defect DCSG00917749)
-change button is not enabled for Behavior params change.(DCSG00426709 (Port Of Defect DCSG00428813)
-LSA : PDs are not listing properly after pull/push from enclosure/Backplane.(DCSG00916164 (Port Of Defect DCSG00917716)
-Fixed: StateChange Event handled to update repository.(DCSG00555478 (Port Of Defect DCSG00708165)
-Fixed: Corrupt image file leads to LSA crash.(DCSG00951718 (Port Of Defect DCSG00960390)
-LSA displays all lane speed values under Manage PCIe storage interface.(DCSG00547375 (Port Of Defect DCSG00549936)
-Fixed: Parameter 16GT is not visible while updating lane speed.(DCSG00255550 (Port Of Defect DCSG00960305)
-LSA MR 7.18: LSA events shows full description of the behavior mode(Jbod) change instead of mentioning Mode name..(DCSG00913588 (Port Of Defect DCSG00960083)
-LSA allows to upgrade without uninstalling previous version of LSA in Ubuntu 18.04.05.(DCSG00435199 (Port Of Defect DCSG00500750)
Headline:.(DCSG00965622 (Port Of Defect DCSG00980121)
-LSA : RHEL 7.9 , Ubuntu 18.04.5 and ESXi7.0u1 OS are missing in Linux LSA readme file & ESXi7.0u1 OS is missing in Windows LSA Readme file.(DCSG00421344 (Port Of Defect DCSG00506913)
-PH19 Alpha - LSA - HBA listed with incorrect index order under view server profile.(DCSG00930402 (Port Of Defect DCSG00960246)
-LSA Windows installation from CDROM fails - error opening installation log file.(DCSG00944480 (Port Of Defect DCSG00944695)
-Addition of 3rd party licenses into the package.(DCSG00501027 (Port Of Defect DCSG00501331)
-Shenandoah_MRSA:Enclosure Location and Status coming as Unknown in MRSA when Click to download all the Enclosure or Backplane properties.(DCSG00412122 (Port Of Defect DCSG00414363)
-VenturaLSA_7_18: Unable to trigger Fast initialization on VDs.(DCSG00959286 (Port Of Defect DCSG00960876)
-Set PR properties are showing offline VDs and user is able to add those offline VDs for Patrol read operation.(DCSG00906763 (Port Of Defect DCSG00919131)
-Foreign import config shows "Incomplete or non-importable foreign config" for secured VD after unlocking with proper keys.(DCSG00423048 (Port Of Defect DCSG00495341)
-LSA : "Unlock" button is not getting enabled if user copy & paste the LKMS passphrase in the security key text box.(DCSG00923594 (Port Of Defect DCSG00925032)
-21B- LSA allows EKM to LKM migartion & ask for Authentication key.(DCSG00920215 (Port Of Defect DCSG00925030)
-Shenandoah_MRSA : OLH link for MRSA OEM build refers to screenshots of non-OEM build.(DCSG00501038 (Port Of Defect DCSG00519848)
-Aero MR : LSA Channel: Drive connector information not displayed correctly when compared with Storcli output.(DCSG00416118 (Port Of Defect DCSG00416248)
-LSA: PD insertion event display issue.(DCSG00840938 (Port Of Defect DCSG00916909)
-Foreign import config shows "Incomplete or non-importable foreign config" for secured VD after unlocking with proper keys.(DCSG00420399 (Port Of Defect DCSG00421316)
-LSA services not starting after installing LSA on RHEL 8.3.(DCSG00915932 (Port Of Defect DCSG00916838)
-LSA Server: Code refresh based on Security Tool findings.(DCSG00500569 (Port Of Defect DCSG00501486)
-LSA : Manage SAS Storage Link Speed is setting values only for 2 phys out of 4 phys if user sets it from LSA.(DCSG00916870 (Port Of Defect DCSG00944446)
-Fixed: state-change isn't updating state of the PD incase of bad to good.(DCSG00834219 (Port Of Defect DCSG00916893)
-LSA : Enable/Disable SSD caching is not working for all VDs at once if user selected multiple VDs and enabling/disabling SSD cache.(DCSG00409275 (Port Of Defect DCSG00415053)
-LSA MR 7.18: Click to download option is enabled in Download snapdump page, eventhough no files are selected for download..(DCSG00922702 (Port Of Defect DCSG00960272)
-Fixed: Added security flags to LSA Makefile.(DCSG00814604 (Port Of Defect DCSG00816013)
-LSA cursor is actively cycling after failed to import the max (240Lds) LDs reached.(DCSG00921402 (Port Of Defect DCSG00922051)
-Addition of 3rd party licenses into the package.(DCSG00501027 (Port Of Defect DCSG00501332)
-Addition of 3rd party licenses into the package.(DCSG00501027 (Port Of Defect DCSG00554176)
-LSA : Loopback IP address is not coming after restarting LSA service if there is no LAN/NIC card.(DCSG00417564 (Port Of Defect DCSG00421192)
-WG: login to manage server page with readonly access and then login to any VMware system, logout to VMware grants readonly user "Admin" previlige.(DCSG00384343 (Port Of Defect DCSG00401650)

EnhancementRequest:
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00388186
-LSA: Add Event for possibility of incomplete writes on parity VDs with no battery backup (ER: DCSG00229751).(DCSG00735186
-Implimented: TCP/HTTP Fortification.(DCSG00436245
-Enable end user tools to read custom SN.(DCSG00938513
-Aero-Margay Connectivity Solution Integration - MR API.(DCSG00956233
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00394652
-Implimented: Additional error code handled.(DCSG00310385
-update dependent to comply with latest OS support.(DCSG00428823
-Upgradation of dependent component with security flags.(DCSG00427912
-Request IT read Product Name/Model Number for SATA drives so that the Product Name/Model Number is displayed in full + FW Version.(DCSG00371060
-Added support for RHEL 8.3.(DCSG00373404
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00388184
-Upgrade of OpenSLL and its dependent components.(DCSG00404741
-LSA: Short term solution for handling SES cable missing to Atlas.(DCSG00735187
-Update 3rdpartyComponents with latest security flags and review deprecated APIs.(DCSG00553596
-Add OpenEuler OS (20.03 LTS) support on Kunpeng 920 Gen4 ARM for Ventura MR/iMR (Driver Binary, StorCLI, Storelib, LSA).(DCSG00546575
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00388185
-MegaAPI: Add API changes for temporary key escrow (PR: DCSG00428069).(DCSG00935525
-Implimented: TCP/HTTP Fortification.(DCSG00436245 (Port Of EnhancementRequest DCSG00937396)
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00388184 (Port Of EnhancementRequest DCSG00394003)
Headline:.(DCSG00427912 (Port Of EnhancementRequest DCSG00432022)
Headline:.(DCSG00427912 (Port Of EnhancementRequest DCSG00431998)
-Linux: LSA service script improvement.(DCSG00841007 (Port Of EnhancementRequest DCSG00903463)
Headline:.(DCSG00404741 (Port Of EnhancementRequest DCSG00427334)
-Update 3rdpartyComponents with latest security flags and review deprecated APIs.(DCSG00553596 (Port Of EnhancementRequest DCSG00553614)
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00394652 (Port Of EnhancementRequest DCSG00447326)
-Update 3rdpartyComponents with latest security flags and review deprecated APIs.(DCSG00553596 (Port Of EnhancementRequest DCSG00654068)
-LSA: Linux 32 bit binary removal.(DCSG00221416 (Port Of EnhancementRequest DCSG00408188)
-Implimented: TCP/HTTP Fortification.(DCSG00436245 (Port Of EnhancementRequest DCSG00941433)
-Implimented: TCP/HTTP Fortification.(DCSG00436245 (Port Of EnhancementRequest DCSG00937397)
-Added support for RHEL 8.3.(DCSG00373404 (Port Of EnhancementRequest DCSG00428725)

			
007.016.021.000 - Moderate Impact
---------------

Defects:
-LSA : While updating UEFI for 440-16e (Aero-IT), "Image update failed" message is coming and next time it passes.(DCSG00935787)

Enhancements:
-Update comment for SL_ERR_IR_INVALID_FW_FLASH_IMAGE_NVDATA.(DCSG00936705)

007.016.015.000 - Moderate Impact
---------------
MR 7.16

Defects:
 -Instance validation fails for Manage Server GET (MR 7.14, 7.014.000.000): Schema 32(DCSG00079899)
 -LSA 7.15 WG: "Replace Missing drive" page will not open after clicking and closing "Assign Dedicated hotspare" page.(DCSG00167347)
 -LSA MR 7.16: While Updating the firmware Selected Firmware Version is showing wrong text instead of Firmware Version.(DCSG00359474)
 -LSA WG : Uninstall instructions mentioned in LSA ESXi readme is wrong.(DCSG00126899)
 -LSA 7.14 : Clicking on "Configure" option from server landing page is redirecting to controller info page instead of Advanced config page.(DCSG00125950)
 -Physical drive Serial number info should be populate in LSA(DCSG00321940)
 -Legacy:WG 7.14 PA2: Unconfigured Bad drive count is not updated for Drive tab when Vds are created.(DCSG00092875)
 -WG: Folder structure remains after uninstalling the direct agent on windows(DCSG00347401)
 -WG: RWC3 Ubuntu Linux build (07.016.003.000)loads with http instead of https(DCSG00384392)
 -Fixed: Clear staging directory to allow new downloads(DCSG00127783)
 -Description of the behavior of the "fast initialization" on RWC3 is inaccurate (Intel re-branded LSI Storage Authority/LSA)(DCSG00263417)
 -Current speed under "Manage PCIe storage interface" is showing like 2.5GT, 5GT, 8GT instead of 2.5GT/s, 5GT/s, 8GT/s(DCSG00301958)
 -WG 7.14: Invalid VD capacity displayed while creating AddVD on a hole with invalid number of VDs(DCSG00080851)
 -Select all checkbox needs to be consistent in all the tabs(DCSG00108298)
 -LSA-Missing rebuild when a drive goes offline by physical removal(DCSG00327294)
 -Fixed: check spdm support bit before populating details(DCSG00108070)
 -Aero : MR 7.16 -Channel: Mismatch between LSA and Storcli output for drive firmware version(DCSG00342645)
 -Update the PD size for higher size 4k Drives(DCSG00395158)
 -Fixed: Security node is being populated for non secure drives(DCSG00140174)
 -LSA MR 7.16: Sorting is not available in "JBOD to Unconfigured Good conversion" page.(DCSG00311369)
 -Enable Drive Security has incorrect phrase and incorrect word. Forcing a Offline PD, confirmation message shows incorrect word.(DCSG00358750)
 -MR 7.16 : Aero Channel : LSA: "Virtual Drives" should be printed for message event id= 195 instead of logical drives(DCSG00316205)
 -LSA WG: Wrong tool tip is seen on Apply button, while filtering the drives.(DCSG00074726)
 -reference to Virtual Drive instead of Logical Drive in ReadMe(DCSG00111540)
 -Fixed: secure discovery handling(DCSG00318199)
 -LSA WG: Help(?) icon present in LWA in "Schedule Consistency check" page.(DCSG00129159)
 -LSA WG 7.15 : Add hotspare option is enabled for spanned raid levels, even after creating VD.(DCSG00226412)
 -Fixed: Import certificate with Seal is not working, Seal is not enabled after import.(DCSG00122476)
 -fixed: update switch to be displayed as managed switch(DCSG00140169)
 -LSA WG: LSA is allowing to add virtual drives more than 16, when spandepth is increased/decreased.(DCSG00084397)
 -Voltage sensor values are shown in negative for atlas board(DCSG00151544)
 -LSA Client: Behavior mode parameters is not shown(DCSG00079966)
 -LSA: While creating 64 slice VD on same DG the 10th VD Name creating as VDName_010 instead of VDName_10(DCSG00253718)
 -WG 7.14 : in AERO IT controller, the enclosure serial number is shown blank, Storcli shows NA(DCSG00138884)
 -Legacy: LSA WG: LSA is allowing to change the personality mode of the controller in Non-admin access.(DCSG00083219)
 -WG: no status code is displayed on failure of "start recover" operation(DCSG00105107)
 -LSA _MR :- Error/warning message not displayed when unsupported characters entered for changing drive rate settings(DCSG00134600)
 -WG 7.14: In Physical Drive properties, Multipath field is showing "Yes" for all the drives attached, eventhough drives are not in Mulitpath configuration.(DCSG00092819)
 -7.14 LSA : Update the LSA readme.(DCSG00108916)
 -WG: LSA Does not have filter button in drives tab for IT controller Controller console page(DCSG00138885)
 -LSA MR 7.16: Sorting is not working after clicking on Filter option in RLM page.(DCSG00359695)
 -LSA MR 7.16: Modify Virtual Drive field is disabled after changing the unit value from GB to MB.(DCSG00345377)
 -WG: Instance Validation failed for event History get,( MR 7.14, 7.014.004.000): MR Ventura: JBOD mode(DCSG00129472)
 -LSA 7.15 WG: "Make JBOD" option is available for the drives which are Prepared for removal.(DCSG00212830)
 -VD Read cache policy displayed wrong as RA , whereas detailed VD policy shows correct(DCSG00148244)
 -MR 7.16 :Channel_ LSA: VD property modification ( WT to AWB) event description not in sync with the actual VD property(DCSG00323028)
 -fixed: Recovery of NVME drives(DCSG00104462)
 -WG: Creation of simple configuration with dedicated hotspare, LSA creation notification does not include hotspare in total PDs used in config creation(DCSG00259092)
 -LSA MR 7.15: Add Virtual Drive field is enabled and VD is added for patrol read, even after unselecting all VDs in Set Patrol read page.(DCSG00228853)
 -In server settings page under email tab, in absence of any email id, Test configurartion should be disabled(DCSG00146660)
 -WG: Selected element minor GUI issue in naming convention, LSA continues to show download in progress continuously(DCSG00151401)
 -MR 7.16 : LSA: Logical ID of enclosure is not displayed correctly(DCSG00316050)
 -LSA 7.14: Set adjustable task rate field is not allowing to save the changes.(DCSG00126266)
 -LSA Client : Handle Manual Discovery failure cases(DCSG00098052)
 -Manage PCIE Storage interface does not show any data.(DCSG00340896)
 -Enclosure Location and Status coming as Unknown when Click to download all the Enclosure or Backplane properties(DCSG00412122)
 -Silent installation with default Web server port and default LSA port is failing.(DCSG00092962)
 -LSA MR 7.16: Number of VDs is not getting updated after deleting the first created VD.(DCSG00361755)
 -When selected 6272 KB firmware for update failure seen with message as file is more than 16MB size(DCSG00080838)
 -LSA Conf: Clean and remove unused fields(DCSG00297566)
 - -WG 7.14 : VD expansion more than 100 % is allowed in LSA(DCSG00126745)
 -"The given port is in use the next available port " message seen During every DA installation(DCSG00412121)
 -LSA MR : Replace Missing drive option is available for Non-admin privileges.(DCSG00298090)
 -WG: login to manage server page with readonly access and then login to any VMware system, logout to VMware grants readonly user "Admin" previlige(DCSG00384343)
 -LSA MR 7.16 :Progress bar is not shown for Rebuild and Patrol read operations for Non-admin privileges.(DCSG00347097)
 -WG: Instance Validation failed for Controllers get,( MR 7.14, 7.014.004.000)(DCSG00129470)
 -for IT Controller update firmware radio buttons and text does not have clickable hand icon(DCSG00138887)
 -Fixed: Added remove files after files are zipped for snap dump download(DCSG00085869)
 -Enclosure location coming as "unknown" for UBM3 if you boot the system without any drives connected(DCSG00081762)
 -LSA: Filter options does not list NVMe drives in PD list of controller console page(DCSG00138709)
 -LSA: Modifying VD properties during Multiple VD creation list the VD name as "VDName_00" instead of VDName & Modify VD page does not have hand symbol for help icon(DCSG00354486)
 -LSA7.16_Linux compiler specific changes(DCSG00340258)
 -Non-interactive/silent installation does not have options to install LSA based on EVENT NOTIFICATION CHOCIES.(DCSG00078199)
 -WG MR 7.14 PA: Clear option grayed for an incomplete foreign configuration(DCSG00085818)
 -Version not reflected correctly when we upgrade MRSA in ubuntu(DCSG00404727)
 -In Set patrol read properties page, Unselected VD is also added for Patrol read.(DCSG00259156)
 -LSA read me: Update the Open Source details(DCSG00353259)
 -updation of libfcgi.dll with DYNAMICBASE flag(DCSG00426989)
 -Change button is enabled when no change performed in Change Behavior Mode(DCSG00382779)
 -MR 7.14 PA2: Rescan Under foreign config menu is grayed out after importing foreign Vd.(DCSG00101341)
 -LSA does not display full message, while making an offline drive online of a VD from Server Landing Page.(DCSG00366127)
 -Fixed: lib utils version update(DCSG00360539)
 -LSA uninstallation is failing on HPE(DCSG00164985)
 -VDs of different capacities(MB/GB) is not sorting properly.(DCSG00080102)
 -Cisco M6: Selecting drive after filter is applied Element selection is shown as "Zero".(DCSG00278212)
 -API clarification for large io support(DCSG00307042)
 -WG 7.14 PA2: 'show password' and 'show key' are active for "Pause for password at boot time" under 'change drive security'.(DCSG00108259)
 -WG: making an offline drive online of a VD from server summary page, LSA does not notify regarding the destructive operation.(DCSG00340323)
 -RWC3 windows build (07.014.004.000)loads with http instead of https(DCSG00125606)
 -Shenandoah_MRSA:Error message not proper for Ubad to UGood for a Bad drive(DCSG00092851)
 -LSA WG: Alignment issue in Manage server page.(DCSG00138055)
 -RWC3 windows Header has LSA Storage Authority as product name instead of RAID Web Console 3.(DCSG00125329)
 -Fixed: Added code to change content type which is acceptable to IE(DCSG00138898)
 -LSA MR 7.15 Alpha: Clicking on "modify" icon will enable the Add Virtual Drive field even after creating a VD of full size(DCSG00293914)
 -fixed: changed unit to Byte in case of zero size drives(DCSG00072680)
 -LSA Windows: Usage of nginx 1.18 version which is a stable version(DCSG00324413)
 -Fixed:SPDM configuration page shows as blank In LSA(DCSG00138574)
 -Legacy : LSA WG 7.14: Remove Manage server icon is not placed properly for Manually added ESXi servers in List view.(DCSG00110210)
 -MR 7.16 :Channel_ LSA: Missing warning message when tried to modify PCIe Storage Interface(DCSG00358742)
 -Use NVRAM to save PTB information -- API changes(DCSG00082981)
 -When heavy IOs active, LSA is taking very long time to download server report .(DCSG00092899)
 -MRSA Desktop icon should not be present for Ubuntu as per the Read me(DCSG00099517)
 -WG 7.14 PA2: LSA installation on Ubuntu, fails with error "LSA_lib_utils" : Gateway can not be launched(DCSG00089795)
 -Manage server page throws error message "400:" for invalid credentials.(DCSG00136334)
 -WG 7.14 PA2: Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 7.8(DCSG00092841)
 -WG: LSA fails to create Drive group for Non-span depth supported Raid volumes.(DCSG00089810)
 -x Readme needs some modification on supported OS and reference as MRSA in some places(DCSG00146624)
 -WG: Sorting is not working as expected in drives tab with multiple spans. with a span having a missing drive(DCSG00341095)
 -LSA Windows x64: Some of the OS is having an issue(DCSG00307418)
 -LSA MR 7.16: Sorting based on Drivegroup is not proper in Assign dedicated hotspare page.(DCSG00322767)
 -Launchpad on desktop of Rhel 7.7 is shown as "LaunchLSA" instead of "LaunchMRSA"(DCSG00072655)
 -LSA shows FW update failure message even after FW update is successfull.(DCSG00082492)
 -LSA 7.15 WG: Sorting based on Drive group capacity is not proper in "Assign Dedicated hot spare" page.(DCSG00166089)
 -Update credits files in client credits(DCSG00353889)
 -Shenandoah_MRSA:Event description blank for 628,629 in MRSA(DCSG00325879)
 -Fixed: Monitor Conf files are missing write permission(DCSG00129770)
 -Fixed: Spanned drive min vd check calculation error(DCSG00138063)
 -Update Credits.html with updated licenses(DCSG00428654)
 -LSA MR 7.15 : LSA does not show message while modifying Disk cache policy of VD in Advanced configuration page.(DCSG00263699)
 -Upgrade is not working in ubuntu from 7.15 to 7.16 packages(DCSG00315134)
 -LSA : Loopback IP address is not coming after restarting LSA service if there is no LAN/NIC card(DCSG00417564)
 -MR controller with No Alram is not auto refreshing on changing the controller properties(DCSG00124484)
 -On ARM server, on every reboot LSA services are stopped: Ubuntu 18.04(DCSG00105871)
 -displays 0 Needs attention when we have degraded LDs(DCSG00092831)
 -WG 7.14 : Mismatch seen in the total number of available UG drives and actual no of PDs in PD list during encrypted R60 VD creation.(DCSG00134663)
 -LSA - Set PR properties is showing VD as optimal though it is offline or degraded(DCSG00226300)
 -Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 8.2(DCSG00115253)
 -Fixed: updated Readme with "Health status shown in LSA is as per LSA's health algorithm."(DCSG00412125)
 -LSA MR 7.16: Changing the lane speed in Manage PCIe storage interface page is showing Operation is either not allowed or not supported, whereas storcli shows Success reboot required(DCSG00397804)
 -WG: ""Your connection is not Private" shown twice in "Manage server page"(DCSG00391486)
 -Legacy : WG: LSA auto logs in on clicking "verify" button for "Managed" VMware manually added server in managed server page(DCSG00112178)
 -Fixed: updated nginx and libcurl(DCSG00414394)
 -WG: Sorting does not work in Span tab of VD in presence of missing drive(DCSG00258267)
 -Fixed: Build script changes to pick up the latest conf and ini files(DCSG00125997)
 -SSD WearGuage Estimated Life Remaining in Percent as "N/A" for New Drives(DCSG00074664
 -Fixed: Certificate Algorithm details are showing blank for few certificate slots.(DCSG00123069)
 -LSA fails to import R0 which has pinned cache after a reboot(DCSG00356398)
 -WG: instance validation failed for controllers Operations GET: iMR Ventura : Schema 34: MR 7.16(DCSG00342339)
 -LSA service fails to start when LSA port value is set to 2463(DCSG00083383)
 -Secured foreign locked VDs details are not displayed under foreign configuration to import/clear foreign config(DCSG00103239)
 -LSA Server: WG MR 7.14 PA2: Advance configuration page is in hung state in presence of jbod drive and prepare for removal state(DCSG00114253)
 -Fixed: Invalidate certificate slot is failing with error code 165.(DCSG00122448)
 -LSA WG: Non-span depth supported raid levels are showing "Span depth modify" option in Advanced config page upon clicking on "Compare and select" link.(DCSG00143503)
 -LSA MR 7.15 Alpha: Changing the number of spans while creating DG shows wrong info about the Number of VDs can be added to DG.(DCSG00264033)
 -LWA Compilation Issue Resolution(DCSG00228825)
 -Only the text in "Start recover" operation for bad NVMe drive is clickable(both CC and ss Page), GUI issue on expanding the controller health(DCSG00105108)
 -LSA WG: In Advanced configuration page, hotspare PD adding page disappears when users scrolls up/down the LSA page.(DCSG00080074)
 -MR7.15 LSA Client: Unsupported icon in Server and Controller Dashboard(DCSG00277830)
 -WG: No success or failure icon is shown on silencing alarm, hand symbol is not present for close icons in advanced enclosure properties(DCSG00255201)
 -WG: nginx conf file after installing DA is empty. unable to manage the DA from Gateway though DA LSA service running(DCSG00383999)
 -Clear configuration is success when JBOD has OS(DCSG00382535)
 -LSA Server: Hard coded string over disk and controller implementation(DCSG00152933)
 -Enclosure Name not correct for x4 Backplanes Connected via Straight cables to two controllers.(DCSG00315377)
 -WG: Instance Validation failed for servers get,( MR 7.14, 7.014.004.000)(DCSG00129468)
 -PH15 LSA IT:In RHEL7.8 for enclosure drives Multi path field is showing as"Yes" In Physical Drive properties,without Multipath configuration(DCSG00132726)
 -Shenandoah: MRSA: VD reference in modify LD property ( try to change disk cache and the help balloon refers to VD)(DCSG00324759)
 -SPDM_LSA : There is no successful message displayed for the export CSR action.(DCSG00122457)
 -Memory Leak issues LSA Build(DCSG00149688)
 -Port Box Bay info incorrect for ISE operation page(DCSG00092895)
 -The "More Actions" menu doesn't open up when the RAID controller is ESRT2(DCSG00259353)
 -Enclosure Bay count coming Wrong in(DCSG00074661)
 -Updated Arm read me file with arm specific changes(DCSG00085797)
 -LSA Property: package version mismatch between components in IT(DCSG00307461)
 -Test Configuration button should be disabled till we get the response(DCSG00299771)
 -LSA Client: WG MR 7.14 PA2: Advance configuration page is in hung state in presence of jbod drive and prepare for removal state(DCSG00129756)
 -LSA MR 7.16: Not able to modify the VD size in Advanced configuration page.(DCSG00381677)
 -multi-LUN tool support for multi-actuator drives.(DCSG00122386)
 -Shenandoah_MRSA : Number of hours is wrong in MRSA evetns for Event 544(DCSG00325891)
 -LSA Client: Manage Link Speed not showing the error message(DCSG00310339)
 -Manual Discovery failure shouldn't return HTTP status:200(DCSG00098024)
 -LSA Common: Package 64 bit monitor libraries as part of Windows x64 package(DCSG00307031)
 -Shenandoah_MRSA: Enclosure Type in Server profile is not complete. Needs to allign with CLI(DCSG00081768)
 -LSA: MR-7.14-SPDM tab needs correction.(DCSG00108295)
 -LSA: "Incorrect Connector Name" under physical drive properties.(DCSG00358747)
 -LSA Common: Stale folders still persist in html folder(DCSG00388225)
 -fixed: import of certificate issue(DCSG00094369)
 -Not able to launch MRSA though the launch icon or installer(DCSG00078194)
 -LSA MR 7.15 Alpha : Schedule consistency Check field is showing partially degraded VD as optimal.(DCSG00263547)
 -Event strings not proper in MRSA for 379,383,385(DCSG00325883)
 -Junk characters are getting displayed in enclosure information with no drives connected.(DCSG00074730)
 -LSA MR 7.16: Filter option is not working properly in RLM page.(DCSG00342455)
 -PCI-Switch subtype when enclosure is an pci-switch(DCSG00085935)
 -Predicitive Failure count and Drive temperature not getting updated in PD property page(DCSG00082823)
 -Windows OS crashes after upgrading to LSA 007.014.005.000(DCSG00138044)
 -Shenandoah_MRSA: Controller Drop down not listing all controllers(DCSG00108923)
 -LSA - ICX - Lane speed under Manage PCIe storage interface is showing like 2.5GT, 5GT, 8GT instead of 2.5GT/s, 5GT/s, 8GT/s(DCSG00259499)
 -fixed: Min VD size check for R1 was missing(DCSG00086324)
 -fixed: MFI code stops LSA from showing slot 0 and 1 when it is not configured(DCSG00123067
 -WG 7.14 PA:During the Creation of r60 vd , removal/adding drives creates inconsistency in AddPhysicalDrive and Addhotspare tables.(DCSG00079935)
 -"Compare and Select" page shows Raid 6 with 3 drives(DCSG00087244)
 -Current speed under "Manage SAS storage link speed" is showing like 3Gb, 6Gb, 12Gb instead of 3Gb/s, 6Gb/s, 12Gb/s(DCSG00301640)
 -Drives connected to IT controller reports Shield Counter(DCSG00264740)
 -WG: RWC3 windows build loads with http, instead of https(DCSG00340881)
 -WG 7.14 PA2: Stripe size under DG does not sort properly when multiple Vds are created with different strip sizes.(DCSG00093774)
 -LSA_SPDM : Import certificate chain event id 622 description is not proper.(DCSG00122482)
 -WG MR 7.14 PA1: LSA allows to select 512B drives as DHSP for 4K DG(DCSG00078853)
 -Backplane info is not proper in expanded state(DCSG00106485)
 -Shenandoah_MRSA : Transport feature needs to be removed from array properties(DCSG00081965)
 -Fixed: update approved user list(DCSG00384488)
 -Fixed: Import certificate /Download CSR options are disabled for slot 0 & 1(DCSG00138892)
 -Aero MR : LSA Channel: Drive connector information not displayed correctly when compared with Storcli output(DCSG00416118)
 -Fixed: changed values to comply with schema restrictions(DCSG00140179)
 -LSA WG : LSA "Download Diagonstic" field is not downloading the ttylog in Readonly access.(DCSG00083816)
 -LSA - Error code 169 - Description Shows as Blank.(DCSG00111872)
 -Credits page needs an update(DCSG00232932)
 -WG:LWA:Not all snapdump logs are downloaded on trying to download all the generated snapdump logs(DCSG00216125)
 -MR 7.16 Aero: Storcli displays Enclosure Serial Number as blank whereas LSA shows as "N/A"(DCSG00316066)
 -Fixed: permission of only last node in path was changing(DCSG00384372)
 -After the upgrade or trying to delete through RPM launch Icon is not deleted(DCSG00078205)
 -Fixed: issue resolution message for non-recoverable drive(DCSG00105032)
 -Port information is wrong when SAS drive is connected to UBM3 BP with 416A controller(DCSG00316863)
 -Fixed: enclosure type and subtype display changes for PCI-switch(DCSG00314948)
 -Remove the individual elements download from MRSA(DCSG00418470)
 -WG: LSA does not allow to change to any other behavior once encountering error during behavior change : GUI Change(DCSG00255157)
 -MR 7.15: LSA fails to launch in Ubuntu.(DCSG00221326)
 -JBOD creation is not allowed through MRSA both on windows and Linux on 7.16 builds(DCSG00317915)
 -Shenandoah_MRSA:Enclosure type not correct for UBM4 backplanes in server profile(DCSG00360535)
 -WG MR 7.16 : Direct agent and standalone does not load on Ubuntu ARM system.(DCSG00395624)
 -Spacing issues on securing a DG as secure, minor GUI issue non notification of enabling scsiUnmap(DCSG00138886)
 -Unable to uninstall the RWC3 on Ubuntu 20.4 when xterm present(DCSG00146748)
 -WG 7.14:During VD creation filtering 4k drives displays blank PD table when mixing is not allowed(DCSG00078974)
 -WG 7.14 PA2: "Unlock" button should be grayed out for Foreign secured locked PD.(DCSG00094756)
 -LSA MR 7.16: Inconsistency while upgrading the LSA.(DCSG00417467)
 -Shenandoah_MRSA: Virtual disk reference in " Make Drive Online" option(DCSG00306847)
 -LSA MR 7.15: Not able to remove the manually added servers.(DCSG00239878)
 -Legacy: LSA WG: In home page, Scroll up option is missing when user expands the Server profile.(DCSG00083860)
 -MR Controller Downloaded Diagnostic Data has Deviceid set to 0 in line number 12(DCSG00125594)
 -fixed: R1 migration form R0 with one UG-good PD(DCSG00312113)
 -WG: RWC3 Ubuntu Linux build shows LSA instead of RWC3 during installation.(DCSG00385902)
 -Foreign import config shows "Incomplete or non-importable foreign config" for secured VD after unlocking with proper keys(DCSG00420399)
 -LSA MR 7.16: VD is expanded to 100%, when user provide the expansion percentage value between 0.1 to 0.5(DCSG00303650)
 -Legacy WG: Verify Credentials of the manually discovered server in Manage server page does not check if server is down(DCSG00080854)
 -Uninstall the RWC3 does not remove the complete folder structure(DCSG00125612)
 -WG: empty enclosure ID and slot ID is displayed for NVMe initialization event in event logs(DCSG00105113)
 -SAS address is shown for PCIe (NVME) drives instead of WWID(DCSG00138744)
 -Health status changes of the remote server does not get updated in the gateway remote discovery page(DCSG00086628)
 -Shenandoah: MRSA events for enclosure insertion not in sync with firmware logs(DCSG00303613)
 -LSA is showing wrong "LSA_lib_utils" version while uninstalling in linux.(DCSG00083760)
 -WG 7.14 PA2:managed server icon for self server is shown "add" in manage server page if we add ubuntu/ any server to manage server list.(DCSG00112829)
 -WG: Instance validation fails for Configuration service GET, LSA build : MR 7.14, 7.014.000.000(DCSG00079959)
 -LSA MR 7.15: Reload option should not be available in Remote discovery page.(DCSG00235388)
 -Shenandoah: MRSA: keyType information wrong in MRSA for event 343(DCSG00333167)
 -Whitley ICX : LSA - Add physical drives option is not coming for user when trying to recon from R6 to R0(DCSG00104470 (Port Of Defect DCSG00105105)
 -7.14: Update read me files(DCSG00221381 (Port Of Defect DCSG00226031)
 -Handling Manual Discovery ADD case(DCSG00077625 (Port Of Defect DCSG00101928)
 -behavior mode values is not being set properly(DCSG00426348 (Port Of Defect DCSG00426351)
 -AV_RAID_MODE:Missing drive info not displayed when performed on PDs of multiple DGs(DCSG00411847 (Port Of Defect DCSG00415015)
 -LSA_Server: Mismatch in "disk cache policy" during VD creation and after VD creation(DCSG00404783 (Port Of Defect DCSG00408997)
 -LSA uninstallation is failing on HPE(DCSG00164985 (Port Of Defect DCSG00164991)
 -"delete config" command clears the config, when OS/FS in the drive without "force" option.(DCSG00077464 (Port Of Defect DCSG00101933)
 -WG: Instance validation fails for PHY's GET and phy/0 GET (MR 7.13, 7.013.004.000)(DCSG00066942 (Port Of Defect DCSG00078972)
 -CSET Port of Defect DCSG00078494: Lone LF in body of email message(DCSG00078494 (Port Of Defect DCSG00078973)
 -Connected device under "Manage PCIe storage interface" is not showing any NVMe drive details(DCSG00302010 (Port Of Defect DCSG00314950)
 -Fixed: updated configured PD to include offline and failed drives(DCSG00382593 (Port Of Defect DCSG00404817)
 -WG: Manually added VMware server continues to show and does not get auto discovered.(DCSG00243976 (Port Of Defect DCSG00312021)
 -LSA : Modify properties option is not coming to user for CC VD using 730-8i controller(DCSG00408495 (Port Of Defect DCSG00415046)
 -Fixed: Parameter 16GT is not visible while updating lane speed(DCSG00255550 (Port Of Defect DCSG00421350)
 -LSA Server: Manual discovery fix(DCSG00246091 (Port Of Defect DCSG00312023)
 -WG: VMware user able to download LSA logs of gateway(DCSG00384359 (Port Of Defect DCSG00395338)
 -LSA Conf: Clean and remove unused fields(DCSG00297566 (Port Of Defect DCSG00347725)
 -On ARM server, on every reboot LSA services are stopped: Ubuntu 18.04(DCSG00105871 (Port Of Defect DCSG00137404)
 -update HBA 440-16i UEFI BSD failed via LSA(DCSG00074275 (Port Of Defect DCSG00101747)
 -LSA Client: Manage Link Speed not showing the error message(DCSG00310339 (Port Of Defect DCSG00310340)
 -Changing the ngroups list values(DCSG00102619 (Port Of Defect DCSG00103258)
 -LSA Property: package version mismatch between components in IT(DCSG00307419 (Port Of Defect DCSG00312026)
 -LSA Client: WG MR 7.14 PA2: Advance configuration page is in hung state in presence of jbod drive and prepare for removal state(DCSG00129756 (Port Of Defect DCSG00152277)
 -LSA_Avenger: Modify VD properties page is not opening, when VD is created from Simple configuration.(DCSG00337910 (Port Of Defect DCSG00345130)
 -LSA Avenger: Sorting based on VD capacity is not working when VD with size more than 1 TB is present in DG(DCSG00321981 (Port Of Defect DCSG00335909)
 -LSA Advanced Configuration does not work with controller is with RAID mode , Personality behavior=RAID-0(DCSG00063716 (Port Of Defect DCSG00065591)
 -LSA_Avenger: filtering and then sorting drives which are used in vd creation , drives table goes blank.(DCSG00354629 (Port Of Defect DCSG00363767)
 -LSA : Enable/Disable SSD caching is not working for all VDs at once if user selected multiple VDs and enabling/disabling SSD cache(DCSG00409275 (Port Of Defect DCSG00415052)
 -LSA report Power supply status only after LSA service restart(DCSG00086465 (Port Of Defect DCSG00102025)
 -PH15 LSA IT:In RHEL7.8 for enclosure drives Multi path field is showing as"Yes" In Physical Drive properties,without Multipath configuration(DCSG00132726 (Port Of Defect DCSG00138842)
 -MR7.15 Alpha (DBU) WG: unable to change the behavior mode to "none" on Aero controller(DCSG00278399 (Port Of Defect DCSG00312025)
 -CSET Port of Defect DCSG00355995: LSA imports all foreign configs while importing 240VDs, but it shows error message "The server could not import foreign configurations" (Error Code:2)(DCSG00355995 (Port Of Defect DCSG00395255)
 -Cisco - CSCvv26000: C240 M6 : Improper display of RAID5 VD size while creating VD through LSA in Zuma beach(DCSG00313412 (Port Of Defect DCSG00325945)
 -LSA- ICX : Profile properties shows that WB volumes support as "False" under controller Info(DCSG00254886 (Port Of Defect DCSG00278008)
 -MR 7.15 - LSA Event Log is showing Default Read Policy as Always Read Ahead ...needed to be "Read Ahead" instead(DCSG00299006 (Port Of Defect DCSG00307816)
 -Fixed: updated nginx and libcurl(DCSG00414394 (Port Of Defect DCSG00419679)
 -Shenandoah_MRSA: Controller Drop down not listing all controllers(DCSG00108923 (Port Of Defect DCSG00110220)
 -LSA Client : Handle Manual Discovery failure cases(DCSG00098052 (Port Of Defect DCSG00112023)
 -ICX_Whitley_Orion: LSA- Link speed details are not showing properly for Tape drive in WebGUI(DCSG00075777 (Port Of Defect DCSG00102597)
 -Manual discovery page gets hung while adding the server to Auto discovery list.(DCSG00080451 (Port Of Defect DCSG00102024)
 -WG:LSA provides controller operation option of starting patrol read when there are only raid 1 VDs created using NMVe PD's(DCSG00257688 (Port Of Defect DCSG00312024)
 -RWC3 for Windows breaks when testing email on SMTP Port 587(DCSG00298491 (Port Of Defect DCSG00307805)

EnhancementRequest:
 -LSA credits page update with latest open source components(DCSG00074643)
 -LSA Client: NVMe Drive Init failure Error Reporting(DCSG00085790)
 -LSA Server: NVMe Drive Repair - Handling Event(DCSG00086254)
 -Added the current Speed Column to phy and lane speed table(DCSG00075198)
 -MegaAPI: Add API changes for Support Parity Read Cache Bypass (PR: DCSG00245039)(DCSG00370441)
 -MR API: Change event class for SPDM events(DCSG00134416)
 -API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI STAT(DCSG00222915)
 -LSA_Server: Fetch and Display Port name and Box number for NVMe drives with Init error/repair(DCSG00373455)
 -Update X-Content-Type-Options to Header(DCSG00342485)
 -LSA changes to implement the PR:DCSG00152043(DCSG00216430)
 -Restore Factory Default doesn't prompt user to reboot the system after being performed(DCSG00120443)
 -(DCSG00082479)
 -MR7 - LSA_Common: Support WJ Pinning for both WB and WT Parity RAID VDs(DCSG00214470)
 -API change to add connector index as part of NVMe Init Error drive information(DCSG00352896)
 -SPDM support changes(DCSG00092939)
 -LSA 64bit support - disconnect 32 bit(DCSG00243701)
 -Update Nginx Settings and allow download server report for admin users(DCSG00347344)
 -MegaAPI: Add Event for possibility of incomplete writes on parity VDs with no battery backup (ER: DCSG00229751)(DCSG00405671)
 -Support for Ubuntu v18.04 OS(DCSG00081316)
 -MFI SMP Port Num API changes(DCSG00257777)
 -Upgrade of OpenSLP source Code(DCSG00167228)
 -Warning events including Predictive failure (code 96) to add the new property to the drive(DCSG00074191)
 -Cleaning up LSA Readme file(DCSG00086337)
 -Major version upgrade of OpenSSL(DCSG00075194)
 -LSA Common: Enhance OEM build generation on Standalone server(DCSG00138907)
 -MR7.15: LSA - Linux 32 bit binary removal in Standalone Environment(DCSG00228734)
 -LSA Server: Enhance development environment to maintain OEM specific projects(DCSG00129446)
 -Add new security events(DCSG00167313)
 -Multi path Display Enhancement in the Client(DCSG00075193)
 -LSA_7.16: Enhance Make Release process(DCSG00339979)
 -Enhance LightWeightMonitor build process(DCSG00093307)
 -MR API: create a new DCMD for BMC to initiate an expander reset(DCSG00362825)
 -SMART Polling Improvement- API Changes(DCSG00214352)
 -LSA MR7.16: Ruby SED Support(DCSG00265657)
 -storcli does not show the SAS Address of the enclosure(DCSG00255107)
 -MR API: reclassify MR_EVT_CTRL_FW_VALID_SNAPDUMP_AVAILABLE as informational(DCSG00292323)
 -Eliminate reporting of capacitance over 100%(DCSG00149664)
 -Shenandoah: Reverting back the changes made for Span setting for RAID 1 & 10(DCSG00074194)
 -Updated 3rd party libs(DCSG00286594)
 -New MFI Stat for the updated recon behavior(DCSG00229416)
 -MegaAPI: rename WJ events and change event messages (PR: DCSG00166915)(DCSG00332867)
 -MegaAPI: Add API changes for Support WJ Pinning for both WB and WT Parity RAID VDs (PR: DCSG00166915)(DCSG00312334)
 -NVME Failed drive error reporting(DCSG00085936)
 -System Health Status update in case of multiple controllers present in system.(DCSG00075224)
 -(DCSG00082474)
 -MR7 API: Add package incompatibility reporting(DCSG00231443)
 -MegaAPI: Add API Controller Properties and MFCD for ParityReadCacheBypass (PR: DCSG00237022)(DCSG00282676)
 -Manual Discovery Enhancements(DCSG00149397)
 -SPDM Support for Aero in LSA GUI(DCSG00076958)
 -Script build process for arm and esxi LSA(DCSG00075216)
 -LSA 64bit support - disconnect 32 bit(DCSG00243703)
 -Additional NameSpace behavior changes(DCSG00383671)
 -Add the Force Refresh for Cache module in LSA(DCSG00219527)
 -SMART Polling Improvement - API Changes(DCSG00246317)
 -To add return status MFI_STAT_OK_REBOOT_REQUIRED to MR_DCMD_LD_SET_PROPERTIES in mr.h(DCSG00256271)
 -Additional FDE type for Ruby SED support(DCSG00055878)
 -LSA Client: NVMe Drive Repair(DCSG00085927)
 -Build Enhancement - Automate standalone build generation(DCSG00075220)
 -Populating port name of a UBM U.2/3 backplane with NVMe drives(DCSG00132390)
 -MR_SAS_PHY_LINK_SPEED should indicate that the link is not active(DCSG00073569)
 -MR7.16 - LSA Server: SAS Address and LogicalID fields missing in enclosure properties(DCSG00255108)
 -Optimize Server Report Generation(DCSG00351905)
 -LSAServer: Add the Force Refresh for Cache module in LSA(DCSG00218902)
 -Convert LSA installation scripts from csh to sh(DCSG00075219)
 -Remove bays on port for Shenandoah For MRSA(DCSG00101417)
 -LSA Common: NVMe Drive Repair - Event and MFI state notification(DCSG00086253)
 -Multi path Enhancement in the server(DCSG00071167)
 -Upgrade the Install Shield Version to 2020(DCSG00219077)
 -Optimize LSA Server code Compilation Time(DCSG00075222)
 -LSA Server: Autoconfig API Improvement(DCSG00212945)
 -Upgrade GWT from 2.8.1 to 2.8.2(DCSG00110240)
 -LSA Server: NVMe Drive Repair(DCSG00085947)
 -Enhance Standalone RWC3 build process(DCSG00124860)
 -API changes to expose MR_AUTO_CFG_PARAMETER for NONE mode(DCSG00151058)
 -Request to add checks (DevId, SubDevice Id) check prior to flashing(DCSG00396121)
 -Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API(DCSG00226286)
 -(DCSG00152596)
 -Implemented: setting appropriate permission for files and directories(DCSG00351962)
 -LSA needs to add the new adapter name to the support matrix hence marking it to Small to update the support matrix in readme(DCSG00075062)
 -Upgrade of OpenSLL and its dependent components(DCSG00124493)
 -LSA Client - Optimize Client Compilation Time(DCSG00075225)
 -MR7 : Support WJ Pinning for both WB and WT Parity RAID VDs(DCSG00214471)
 -API change to replace enum declaration with U32.(DCSG00393987)
 -API changes for reporting missing cables(DCSG00313199)
 -Changes to support 16port connection to Expander with AeroIOC(DCSG00254845)
 -MR 7.16: Make environment to generate MRMON 64 bit libraries(DCSG00308331)
 -MR API changes - Support new Provisional bit in CTRL INFO and new MFI status for Platform Security SPDM(DCSG00106380)
 -Updated 3rd party libs(DCSG00286594 (Port Of EnhancementRequest DCSG00384441)
 -LSA_Server: Display Write Cache Settings for PD(DCSG00366367 (Port Of EnhancementRequest DCSG00373491)
 -Update Nginx Settings and allow download server report for admin users(DCSG00347344 (Port Of EnhancementRequest DCSG00354847)
 -Updated 3rd party libs(DCSG00286594 (Port Of EnhancementRequest DCSG00306730)
 -LSA Server: RRB141 - Ensure that the SSD cache policy is changeable and the status information is correct(DCSG00171246 (Port Of EnhancementRequest DCSG00228742)
 -Optimize Server Report Generation(DCSG00351905 (Port Of EnhancementRequest DCSG00384509)
 -(DCSG00167228 (Port Of EnhancementRequest DCSG00167257)
 -LSAServer: Add the Force Refresh for Cache module in LSA(DCSG00218902 (Port Of EnhancementRequest DCSG00225933)
 -Crypto Erase option for Cryptographic Capable Drive(DCSG00373462 (Port Of EnhancementRequest DCSG00384657)
 -LSA: Linux 32 bit binary removal(DCSG00221416 (Port Of EnhancementRequest DCSG00363675)
 -Linux: Installer script improvement(DCSG00130050 (Port Of EnhancementRequest DCSG00230033)
 -Implemented: setting appropriate permission for files and directories(DCSG00351962 (Port Of EnhancementRequest DCSG00384472)
 -LSA_Common: Fetch and Display Port name and Box number for NVMe drives with Init error/repair(DCSG00373455 (Port Of EnhancementRequest DCSG00373474)
 -Update X-Content-Type-Options to Header(DCSG00342485 (Port Of EnhancementRequest DCSG00384513)
 -(DCSG00075222 (Port Of EnhancementRequest DCSG00081005)
 -(DCSG00098812 (Port Of EnhancementRequest DCSG00105863)
 -LSA: Linux 32 bit binary removal(DCSG00221416 (Port Of EnhancementRequest DCSG00408121)
 -SPDM support changes(DCSG00092939 (Port Of EnhancementRequest DCSG00113254)
 -BST Automation for LSA(DCSG00098812 (Port Of EnhancementRequest DCSG00218817)
 -Implemented: setting appropriate permission for files and directories(DCSG00351962 (Port Of EnhancementRequest DCSG00354907)
 -CSET Port of EnhancementRequest DCSG00075194: Major version upgrade of OpenSSL(DCSG00075194 (Port Of EnhancementRequest DCSG00083924)
 -MR7.15: LSA - Linux 32 bit binary removal in Standalone Environment(DCSG00228734 (Port Of EnhancementRequest DCSG00293989)
 -Update X-Content-Type-Options to Header(DCSG00342485 (Port Of EnhancementRequest DCSG00348015)
 -CSET Port of EnhancementRequest DCSG00075194: Major version upgrade of OpenSSL(DCSG00075194 (Port Of EnhancementRequest DCSG00083925)
 -Added support for RHEL 8.3(DCSG00373404 (Port Of EnhancementRequest DCSG00428563)
 -(DCSG00096553 (Port Of EnhancementRequest DCSG00110100)
 -(DCSG00085947 (Port Of EnhancementRequest DCSG00086469)
 -(DCSG00286594 (Port Of EnhancementRequest DCSG00290207)
 -Update Nginx Settings and allow download server report for admin users(DCSG00347344 (Port Of EnhancementRequest DCSG00384205)
 -Update Nginx Settings and allow download server report for admin users(DCSG00347344 (Port Of EnhancementRequest DCSG00384206)
 -Implemented: setting appropriate permission for files and directories(DCSG00351962 (Port Of EnhancementRequest DCSG00385127)
 -Ensure that the SSD cache policy is changeable and the status information is correct(DCSG00214163 (Port Of EnhancementRequest DCSG00230031)
 -Optimize Server Report Generation(DCSG00351905 (Port Of EnhancementRequest DCSG00384499)
 -(DCSG00286594 (Port Of EnhancementRequest DCSG00286739)
 -LSA_client: Display Write Cache Settings for PD(DCSG00372331 (Port Of EnhancementRequest DCSG00383405)
 -Added support for RHEL 8.3(DCSG00373404 (Port Of EnhancementRequest DCSG00428561)
 -Optimize Server Report Generation(DCSG00351905 (Port Of EnhancementRequest DCSG00366266)
 -Crypto Erase option for Cryptographic Capable Drive(DCSG00369727 (Port Of EnhancementRequest DCSG00384592)
 -WebGUI: Automate the test cases specific to MR7.14 Product Requirements(DCSG00082499 (Port Of EnhancementRequest DCSG00086646)
 -Update X-Content-Type-Options to Header(DCSG00342485 (Port Of EnhancementRequest DCSG00384514)


007.013.016.000 - Moderate Impact
---------------
MR 7.13

Defects:
-Legacy WG: Verify Credentials of the manually discovered server in Manage server page does not check if server is down.(DCSG00112141 (Port Of Defect DCSG00080854))
-Legacy : WG: LSA auto logs in on clicking "verify" button for "Managed" VMware manually added server in managed server page.(DCSG00112744 (Port Of Defect DCSG00112178))
-MR controller with No Alram is not auto refreshing on changing the controller properties.(DCSG00124768 (Port Of Defect DCSG00124484))
-LSA _MR :- Error/warning message not displayed when unsupported characters entered for changing drive rate settings.(DCSG00136282 (Port Of Defect DCSG00134600))
-LSA Server: WG MR 7.14 PA2: Advance configuration page is in hung state in presence of jbod drive and prepare for removal state.(DCSG00219183 (Port Of Defect DCSG00114253))
-LSA WG : LSA "Download Diagonstic" field is not downloading the ttylog in Readonly access..(DCSG00219184 (Port Of Defect DCSG00083816))
-Secured foreign locked VDs details are not displayed under foreign configuration to import/clear foreign config.(DCSG00221295 (Port Of Defect DCSG00103239))
-Credits page needs an update.(DCSG00233292 (Port Of Defect DCSG00232932))
-WG 7.14 PA2: Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 7.8.(DCSG00233700 (Port Of Defect DCSG00092841))
-On ARM server, on every reboot LSA services are stopped: Ubuntu 18.04.(DCSG00233701 (Port Of Defect DCSG00105871))
-Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 8.2.(DCSG00233702 (Port Of Defect DCSG00115253))
-MR Controller Downloaded Diagnostic Data has Deviceid set to 0 in line number 12.(DCSG00233703 (Port Of Defect DCSG00125594))
-LSA 7.14 : Clicking on "Configure" option from server landing page is redirecting to controller info page instead of Advanced config page..(DCSG00233704 (Port Of Defect DCSG00125950))
-fixed: changed unit to Byte in case of zero size drives.(DCSG00233705 (Port Of Defect DCSG00072680))
-Non-interactive/silent installation does not have options to install LSA based on EVENT NOTIFICATION CHOCIES..(DCSG00233706 (Port Of Defect DCSG00078199))
-WG MR 7.14 PA1: LSA allows to select 512B drives as DHSP for 4K DG.(DCSG00233708 (Port Of Defect DCSG00078853))
-WG 7.14:During VD creation filtering 4k drives displays blank PD table when mixing is not allowed.(DCSG00233709 (Port Of Defect DCSG00078974))
-LSA Client: Behavior mode parameters is not shown.(DCSG00233710 (Port Of Defect DCSG00079966))
-VDs of different capacities(MB/GB) is not sorting properly..(DCSG00233711 (Port Of Defect DCSG00080102))
-Legacy: LSA WG: LSA is allowing to change the personality mode of the controller in Non-admin access..(DCSG00233712 (Port Of Defect DCSG00083219))
-Silent installation with default Web server port and default LSA port is failing..(DCSG00233713 (Port Of Defect DCSG00092962))
-WG 7.14 PA2:managed server icon for self server is shown "add" in manage server page if we add ubuntu/ any server to manage server list..(DCSG00233714 (Port Of Defect DCSG00112829))
-LSA WG : Uninstall instructions mentioned in LSA ESXi readme is wrong..(DCSG00233716 (Port Of Defect DCSG00126899))
-Manage server page throws error message "400:" for invalid credentials..(DCSG00233717 (Port Of Defect DCSG00136334)
-WG: LSA Does not have filter button in drives tab for IT controller Controller console page.(DCSG00233718 (Port Of Defect DCSG00138885))
-Fixed: Spanned drive min vd check calculation error.(DCSG00233720 (Port Of Defect DCSG00138063))


007.013.014.000 - Moderate Impact
-------------------------------------
MR 7.13

Defects:
 -WG 7.13:Inconsistency in display of "Patrol Read" in the Properties page.(DCSG00071276)
 -Changing the ngroups list values.(DCSG00102619)
 -Shenandoah_MRSA : change personality option should not be enabled for both with linux and windows releases.(DCSG00072698)
 -Whitley ICX : LSA - Add physical drives option is not coming for user when trying to recon from R6 to R0.(DCSG00104470)
 -Fixed: Added disable nginx logging flags.(DCSG00065714)
 -Memory Leak issues in LSA Build.(DCSG00068484)
 -WG: Alignment issues in Remote discovery page, server summary page and Settings page.(DCSG00065480)
 -IT controller is not displayed int the view all controllers tab when it is in needs attention.(DCSG00061513)
 -Manual discovery page gets hung while adding the server to Auto discovery list..(DCSG00080451)
 -WG: Clicking on Manually added server in manage server page leads to blank page (calls fails with 502 error code).(DCSG00063209)
 -LSA: disableOffloadNum field should be match with latest schema.(DCSG00041224)
 -Channel controllers are discovered from MRSA Software.(DCSG00054278)
 -Fixed: user notification client list is not updated.(DCSG00053648)
 -WG 7.13: Hot spare Filter box alignment issue.(DCSG00067986)
 -LSA Common: LSA Crypto OEM specific changes.(DCSG00047290)
 -Windows installer (7.013.004.000) is unsigned.(DCSG00065620)
 -Cannot update CFF 440 FW with LSA.(DCSG00062602)
 -Firmware update page shows "None" for selected firmware.(DCSG00065566)
 -Orion MR PA10 - Foreign config is not showing properly in LSA when user pull/push the PD.(DCSG00053829)
 -due to unhanded battery removal event, battery health status was not reflecting as need attention.(DCSG00040271)
 -WG: Energy pack details does not load on clicking energy pack properties after clicking Refresh energy pack properties.(DCSG00058132)
 -MR7.13: Enhance debug Log level and entries in LSA Common code.(DCSG00041751)
 -Fixed:display of 2 enclose when only one is connected with multi path.(DCSG00069728)
 -LSA MR: Hand symbol is showing for all the fields in Server Profile and it is not clickable.(DCSG00062470)
 -WG: In presence of JBOD, after creating VD using all UG drives, the advanced configuration button gets disabled.(DCSG00065733)
 -update HBA 440-16i UEFI BSD failed via LSA.(DCSG00074275)
 -MRSA Firmware update page shows ,Selected Firmware Package version and it shows Firmware version.(DCSG00051098)
 -WG: Instance validation fails for Enclosure GET( MR 7.13, 7.013.004.000.(DCSG00066930)
 -MR-7.12: LSA VD creation failure message has spacing formatting issue..(DCSG00037910)
 -LSA Client : Non-VMware server is discovered with VMware check box enabled in Manual Discovery.(DCSG00051290)
 -Partial degraded VD icon is showing as optimal VD icon in LSA.(DCSG00054282)
 -WG: Duplicate entries of physical drive properties are displayed in case a property of physical drive is updated.(DCSG00069285)
 -WG 7.13: Patrol read option not seen for GHS in LSA.(DCSG00068977)
 -WG: Instance validation fails for Controllers GET (MR 7.13, 7.013.004.000), : Aero Controller.(DCSG00067932)
 -Remote discovery fails to load in RWC3 (7.013.009.000.(DCSG00083835)
 -Fixed: usage of wrong enum led to unknow characters in max lane width.(DCSG00049771)
 -WG: For the self server adding a read only user in manage-server page is logged in as a admin user.(DCSG00065605)
 -AMD 2P - LSA is not showing proper information when user trying to do RLM with same RAID level.(DCSG00040578)
 -MR 7.13 DBU: Flashing BIOS package failure with Completed status on Aero Controller when selected EFI-BSD.(DCSG00055757)
 -Windows Un-installer is not removing the SL Debug logs.(DCSG00054660)
 -WG MR7.13: LSA read me file needs to be updated with New OS matrix and inclusion of Aero cards.(DCSG00055714)
 -WG: Refresh energy pack properties displays error notification with status code : 1 on Vmware login.(DCSG00058321)
 -Notification for Enable /Disable security box is not pointing to Enable/Disable security option..(DCSG00067992)
 -LSA Server: LSA Crypto OEM specific changes.(DCSG00047618)
 -Handling Manual Discovery ADD case.(DCSG00077625)
 -LSA is not allowing user to change max number of PDs allowed under Set Patrol Read properties.(DCSG00068620)
 -Negotiated width and Max lane width property parameters for Nvme drives is shown as "Max user count reached" in LSA.(DCSG00046456)
 -Unmap property not update in VD/PD on enabling/disabling unmap at controller level.(DCSG00040172)
 -Server Profile _Linux: enclosure/Backplane information is blank / ServerIP is private in Linux OS.(DCSG00072694)
 -key board short cut does not work after using the print button during the installation.(DCSG00064684)
 -MR-7.13: LSA event ID 614 shown as Blank..(DCSG00037968)
 -WG: Changes required in naming convention of LSA to RWC3 in linux installation, RWC3 end user text has junk unicode characters in place of quotes and typo's.(DCSG00058406)
 -LSA_ 32 bit installer fails to launch in RHEL 8.1.(DCSG00087274)
 -Shenandoah:MRSA- Online Help gives 404 Not Found.(DCSG00051063)
 -Manage SAS Storage Link Speed/Premium feature/Manage Pcie Storage Interface operations have missing table borders & issues pertaining to column separators of the table.(DCSG00068937)
 -LSA MR : Each box in the List view of server page shows handsymbol but it is not clickable.(DCSG00062228)
 -RWC3 Common: Updating x64 nginx file.(DCSG00068595)
 -WG: clickable Checkboxes and "Confirm" notification texts does not have clickable mouse hover hand icons.(DCSG00069230)
 -LSA Client : NVMe Drive property changes w.r.t schema v32.(DCSG00079364)
 -MRSA shows " 0 Needs attention " when controller health status is "Needs attention ".(DCSG00056573)
 -WG: No LSA support logs generated with 7.013.003.00 linux Gateway.(DCSG00059955)
 -Orion MR PA10 - Same RAID level migration throws an error in LSA if user adding and removing any drives.(DCSG00053821)
 -Enhance the message of locked foreign can not be imported to cover boot time password skip.(DCSG00071157)
 -LSA Client : disableOffloadNum field should be match with latest schema.(DCSG00053497)
 -LSA Server: Resolving merge issues.(DCSG00032674)
 -Fixed:handled discovering multiple controllers.(DCSG00024769)
 -AMD 2P Wave2: LSA- Not able to create RAID00 with more than 32 PDS.(DCSG00042409)
 -Lone LF in body of email message.(DCSG00078494)
 -LSA is getting timed out while creating R6-64 VDs using 32 PDs.(DCSG00049772)
 -AMD2P-Wave2- LSA: Same RAID level migration throws an error in LSA if user adding and removing any drives.(DCSG00068647)
 -Ventura MR FW: Push Pull of drives showing wrong Enclosure ID..(DCSG00060541)
 -WG: Few of the keyboard shortcut keys are not working in case of RWc3 installation.(DCSG00058142)
 -MR-7.13: LSA Foreign import button not grey out after import is clicked with 240 VDs..(DCSG00068136)
 -StorCLI and LSA are not in sync while displaying the NVMe drive model Number after inserting the drive back..(DCSG00054602)
 -WG: Instance validation fails for PHY's GET and phy/0 GET (MR 7.13, 7.013.004.000.(DCSG00066942)
 -Use NVRAM to save PTB information -- API changes.(DCSG00082981)
 -Issue found due to code merge during code delivery process.(DCSG00075210)
 -Fixed: updated build script to add dirty bit to modifiable files. configuration file for client wasnot set with modifiable bit (+T)..(DCSG00058424)
 -MRSA: Supported controller information in the Readme File needs to be updated.(DCSG00056669)
 -Enter Key issue in Manual Discovery page is searching the servers without entering the IP..(DCSG00071404)
 -WG: For the self server which will be added to managed server by default should not show verify button.(DCSG00068954)
 -ICX_Whitley_Orion: LSA- Link speed details are not showing properly for Tape drive in WebGUI.(DCSG00075777)
 -"delete config" command clears the config, when OS/FS in the drive without "force" option.(DCSG00077464)
 -RWC3 windows build (07.013.009.000)loads with http instead of https.(DCSG00083839)
 -LSA MR Ventura: Alarm info is showing wrong when controller info tab is expanded..(DCSG00062219)
 -LSA report Power supply status only after LSA service restart.(DCSG00086465)
 -WG: LSA install shield says ready to install "OpenSLP 3.0.0.0 Arm64" instead of "openSLP 2.0.0.0 x86".(DCSG00063219)
 -Channel controllers are discovered from MRSA Software.(DCSG00053971)
 -Fixed: updated max drives for configuration service API.(DCSG00045337)
 -WG: Issues pertaining to schedule consistency check.(DCSG00069219)
 -Fixed: used data drives instead of total drive whie calculating min vd size.(DCSG00033996)
 -Orion_LSA: Maddux_Chinook: Slot numbers shown as 255 after expander resets.(DCSG00045472)
 -Fixed: Added minimum log support for thin OS.(DCSG00058212)
 -Display of unmap property at VD level.(DCSG00037620)
 -After installation of HPE_Generic linux 64 bit RPM, LSA service is not getting started..(DCSG00056838)
 -WG: Typo's in Readme and LSA.conf.(DCSG00058412)
 -Typo's in LSA.conf.(DCSG00061049)
 -WG: Copyright info needs to be updated from 2019 to 2020.(DCSG00068495)
 -LSA Readme file has to be updated for Aero controller support and proper open SLP web link..(DCSG00054273)
 -Inconsistency in the Server profile Headline representation.(DCSG00068909)
 -WG: Manual discovery page allows the user to add already added manually added VMware server.(DCSG00059470)
 -LSA Server: RAID volume creation failing with strip size conversion.(DCSG00048632)
 -LSA Client : Slot numbers shown as 255 after expander resets.(DCSG00055108)
 -LSAServer: Labeling mismatch between Enclosure Index and Enclosure ID.(DCSG00008078 (Port Of Defect DCSG00025255))
 -Ubuntu Linux install issues.(DCSG00032286 (Port Of Defect DCSG00033488))
 -LSA does not display Virtual drive info for foreign configuration.(DCSG00035555 (Port Of Defect DCSG00071356))
 -Legacy WG: Verify Credentials of the manually discovered server in Manage server page does not check if server is down.(DCSG00080854 (Port Of Defect DCSG00112141)
 -Fixed:LSA increased memory consumption with each event.(DCSG00031835 (Port Of Defect DCSG00070333))
 -Fan, Temperature Sensor , Voltage Sensor property issues related to Atlas board.(DCSG00035711 (Port Of Defect DCSG00071360)
 -Credits page needs an update.(DCSG00232932 (Port Of Defect DCSG00235896))
 -LSA _MR :- Error/warning message not displayed when unsupported characters entered for changing drive rate settings.(DCSG00134600 (Port Of Defect DCSG00136282))
 -LSA Advanced Configuration does not work with controller is with RAID mode , Personality behavior=RAID-0.(DCSG00063716 (Port Of Defect DCSG00065590))
 -When create or delete VD in LSA, VD information didn't refresh under LSA web in VMWare 6.7.(DCSG00068509 (Port Of Defect DCSG00069274))
 -LSA getting hung while loading in windows 2019 OS on Stonyford server.(DCSG00058328 (Port Of Defect DCSG00058797)
 -Health status changes of the remote server does not get updated in the gateway remote discovery page.(DCSG00086628 (Port Of Defect DCSG00087296)
 -Fixed: updated build script to add dirty bit to modifiable files. configuration file for client wasnot set with modifiable bit (+T)..(DCSG00058424 (Port Of Defect DCSG00071283))
 -RWC3 Home Page Help Button Hyper Link is Broken.(DCSG00050748 (Port Of Defect DCSG00061255))
 -LSA Client : Handle Manual Discovery failure cases.(DCSG00098052 (Port Of Defect DCSG00098056)
 -Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 8.2.(DCSG00115253 (Port Of Defect DCSG00239461)
 -LSA read me: Update the read me with all the required OS list.(DCSG00222589 (Port Of Defect DCSG00239476))
 -When selected 6272 KB firmware for update failure seen with message as file is more than 16MB size.(DCSG00080838 (Port Of Defect DCSG00102801))
 -Fixed: updated build script to add dirty bit to modifiable files. configuration file for client wasnot set with modifiable bit (+T)..(DCSG00058424 (Port Of Defect DCSG00070664)
 -Manual Discovery failure shouldn't return HTTP status:200.(DCSG00098024 (Port Of Defect DCSG00098034)
 -MR controller with No Alram is not auto refreshing on changing the controller properties.(DCSG00124484 (Port Of Defect DCSG00124768))
 
 EnhancementRequests:
 -Support for the New Energy Pack states.(DCSG00042776)
 -Implement changes to secureSign signing tool and infrastructure to support mixed list of PublicKeys that are from SCGCQ and DCSG.(DCSG00105430)
 -API change to support ISE completion status.(DCSG00065881)
 -MR API: Change event class for SPDM events.(DCSG00134416)
 -API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI STAT.(DCSG00222915)
 -LSA Standalone - port enhanced authentication/authorization to Linux.(DCSG00025327)
 -DCSG00234646
 -HPE Shenandoah: Type 2 Back plane Support.(DCSG00054712)
 -Linux: Installer script improvement.(DCSG00130050)
 -Remove Span setting for RAID 1 & 10.(DCSG00039596)
 -Preboot Trace Buffer [PTB] for Ventura/Aero - MR API.(DCSG00060713)
 -MR API: NVME Drive Init Error Report and Repair for Aero/Ventura.(DCSG00071534)
 -Implement support for Cross certificate and command - Windows signing using CNG Provider with HSM Protected Key.(DCSG00030211)
 -Allows cleaner exit with flushing of logs.(DCSG00039065)
 -DCSG00129388
 -DCSG00067060
 -Define MR_SAS_PHY_CONNECTION.currentSpeed when no devices are connected.(DCSG00071066)
 -Enhance debug Log level and entries in LSA Server code.(DCSG00038025)
 -Signing Linux executables via GPG method in HSM.(DCSG00077215)
 -Implemented: Logs levels appropriated.(DCSG00038028)
 -MR7.13: Enhance debug Log level and entries in LSA Server code.(DCSG00038019)
 -Request to change all BBU messages to CacheVault or Energy PAck as appropriate, since no longer supporting BBUs on latest Ventura products.(DCSG00031355)
 -Implemented secureSignCNG.exe CLI signing tool for Windows Signing..(DCSG00023491)
 -Blocking Management and display of the profile and Personality in MRSA as user can not change profile or personality from MRSA.(DCSG00041350)
 -SSD Wear Gauage.(DCSG00042810)
 -MR API changes - Support new DCMD for Platform Security SPDM.(DCSG00068355)
 -Include new field cannotSetMode in MR_AUTO_CFG_PARAMETER structure..(DCSG00072780)
 -Update RAID Web Console 3 solution to remove or re-direct Feedback.(DCSG00026525)
 -Ensure that the SSD cache policy is changeable and the status information is correct.(DCSG00214163)
 -Port secureSignBin.exe for MARGAY signing to GCP server environment.(DCSG00040377)
 -MR7.13: Enhance debug Log level and entries in LSA Server code.(DCSG00038027)
 -Request to change all BBU messages to CacheVault or Energy PAck as appropriate, since no longer supporting BBUs on latest Ventura products.(DCSG00031716)
 -API changes to expose MR_AUTO_CFG_PARAMETER for NONE mode.(DCSG00151058)
 -MR7.13: Enhance Server report log collection.(DCSG00039063)
 -HPE Shenandoah: Type 2 Back plane Support MRSA Client.(DCSG00054716)
 -Add new security events.(DCSG00167313)
 -Upgrade Install shield 2019.(DCSG00039535)
 -Support for the New Energy Pack states.(DCSG00042778)
 -LDET - Qx-2020 - RRB149 - Add immediate-binding flag to gcc-compiled deliverables.(DCSG00025854)
 -MR API: update field in event structure..(DCSG00093331)
 -Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API.(DCSG00226286)
 -MR7.13 - LSA Client: Update Snapdump save count field in show snapdump command.(DCSG00039516)
 -Updated secureSign.exe CLI tool and server-side controller scripts to use GCP server resources.(DCSG00003371)
 -SMART Polling Improvement- API Changes.(DCSG00214352)
 -LSA Server: RRB141 - Ensure that the SSD cache policy is changeable and the status information is correct.(DCSG00171246)
 -FW SAS MEGA API:Change MR_EVT_CTRL_FLASH_DISALLOWED_SB_KEY_CHANGE_PENDING event from Info to Warning.(DCSG00086780)
 -New MFI Stat for the updated recon behavior.(DCSG00229416)
 -MR API changes - Support new Provisional bit in CTRL INFO and new MFI status for Platform Security SPDM.(DCSG00106380)
 -Add support for signing MegaRAID Legacy BIOS CU Images (CTLR) images.(DCSG00143847)
 -MR7.13 - LSA Server: Update Snapdump save count field in show snapdump command.(DCSG00039505)
 -MR7 API: Add package incompatibility reporting.(DCSG00231443)
 -Aero multi-party signing partial signing of images.(DCSG00048670)
 -DCSG00025854 (Port Of EnhancementRequest DCSG00039673)
 -Multi path Enhancement in the server.(DCSG00071167 (Port Of EnhancementRequest DCSG00075640)
 -Linux LSA HSM based signing support.(DCSG00038899 (Port Of EnhancementRequest DCSG00042392))
 -Ensure that the SSD cache policy is changeable and the status information is correct.(DCSG00214163 (Port Of EnhancementRequest DCSG00240010))
 -LSA credits page update with latest open source components.(DCSG00074643 (Port Of EnhancementRequest DCSG00074715)
 -Windows LSA HSM based signing support.(DCSG00038808 (Port Of EnhancementRequest DCSG00042391)
 

NOTE TO SERVICE - Reference RETAIN #N/A
007.012.015.000  - Moderate Impact
-------------------------------------

Defects Fixed (100)
 -Fixed:LSA increased memory consumption with each event(DCSG00031835)
 -Scheduler Panel not aligned to center if Operations are performed on 32 VDs.(DCSG00016270)
 -Enable SSD guard fails with the error code : 3: Description: The requested command has invalid arguments.(DCSG00008031)
 -WG: Readme changes as part of MR 7.12.(DCSG00031356)
 -fixed: allow Cachecade VD creation.(DCSG00022978)
 -Aero DBU alpha (LSA):LSA crashes when make jbod/UG performed on multiple drives with Schedular wrapper enabled.(DCSG00024414)
 -7.12_EXT New OS support Matrix.(7.12_EXT New OS support Matrix).(DCSG00011435)
 -WG: Filtering with VMware and searching for auto discovered windows/linux server in manual disc page results in both success and failure messages.(DCSG00010481) 
 -fixed: nginx logs consuming large space on disk.(DCSG00032280)
 -WG:alignment issue in notifications.(DCSG00007250)
 -LSAServer: Labeling mismatch between Enclosure Index and Enclosure ID.(DCSG00008078)
 -Hide the Energy pack information when it is not present.(DCSG00031701)
 -Uninstall successful message not seen with RHEL OS & install exists with unary operator message if user provides input other than Y/N.(DCSG00012335)
 -SLES 15 Linux: Installer messages while creating symbolic link.(DCSG00023294)
 -LSAServer: Cleanup unused variables from LSA Crypto algorithm.(LSAServer: Cleanup unused variables from LSA Crypto algorithm)
 -Fan, Temperature Sensor , Voltage Sensor property issues related to Atlas board..(DCSG00035711)
 -"Your connection is not private" text overlap seen at manage server page.(DCSG00017191)
 -StoreLib API: Update SL_GET_ENCL_LIST with cmdParam_1b[0] for extended/legacy enclosure structures.(DCSG00053982)
 -WG: Aero DBU PA6(LSA): Performing VD operations does not update/clear the element count.(DCSG00012010)
 -Fixed: changed packaging script appropriatley.(DCSG00011424)
 -LSA Cache update for PD insert for it ctrls.(DCSG00020315)
 -Login Button gets disabled when user name is filled and Authentication Fails.(DCSG00014659)
 -LSA install exits if the user clicks enter key on any point during installation.(DCSG00026178)
 -MR 7.12: LSA Client- Coverity Defect Fixes.(DCSG00028104)
 -Modify the Alert setting put request to send only delivery mechanism when Email is not modified.(DCSG00007449)
 -MR-7.12: FW EPD bit is enabled in RAID personality Mode..(DCSG00036066)
 -WG: Remote discovery page does not load with RWC3 gateway installation: MR 7.12.(DCSG00057422)
 -Fixed: library to communicate with vmware server for arm.(DCSG00010202)
 -LSAClient: Labeling mismatch between Enclosure Index and Enclosure ID.(DCSG00012720)
 -SLES 15 Linux: Un-Installation is not removing the complete folder structure.(DCSG00023296)
 -fixed: show only eleigible Raid level for migration.(DCSG00025527)
 -WG_7.12: On SLES 15 OS, After login, on doing some basic operations LSA, it redirects to 50x.html.(DCSG00022866)
 -Refresh the Client page on Enclose link Restore and link lost.(DCSG00014979)
 -Resolved built time dependency.(DCSG00008091)
 -LSA Common:Enhance user notification about the unsecured connection.(DCSG00008073)
 -WG 7.12 Alpha:Jbod conversion is not happening with OS drive.(DCSG00031718)
 -WG: no notification regarding "EMAIL/SMTP server related setting get modified" when user hovers between mail server and Email tab while adding email.(DCSG00020145)
 -LSA - AMD 2P Wave 1 - LSA is getting crashed while upgrading from 007.012.004.000 to 007.012.005.000 version.(DCSG00022361)
 -WG:7.12 Alpha : Enable/disable Scsi Unmap option not shown for the VD created using unmap capable drive..(DCSG00026497)
 -LSA Linux: Maintain the resource files across the build upgrade.(DCSG00007897)
 -LSA Server : JBOD removal/insert events in LSA are not compliance with FW Events..(DCSG00032366)
 -(LSA):Facing " ./LSA: ./libssl.so.1.0.0: no version information available" error while LSA installation.(DCSG00022170)
 -Fixed: Simple configuration feature is disabled if unconfigured drives are not available.(DCSG00025334)
 -LSA Common: Update the script files specific to LSA Crypto.(DCSG00031407)
 -IR Client Refresh: On Start/Stop CC.(DCSG00017218)
 -Libutils and Libutils2 scripts changes.(DCSG00012770)
 -LSA does not display Virtual drive info for foreign configuration.(DCSG00035555)
 -WG: Windows Direct agent not getting discovered in remote discovery page as well as manual discovery page.(DCSG00009390)
 -LSA AMD2P Wave 1: User is getting wrong info about max number of PD support for R1/R5 while doing RLM.(LSA AMD2P Wave 1: User is getting wrong info about max number of PD support for R1/R5 while doing RLM)
 -Ubuntu Linux install issues.(DCSG00032286)
 -Fixed: Slpd supported for rhel/sles/ubuntu is packaged.(Fixed: Slpd supported for rhel/sles/ubuntu is packaged)
 -StoreLib header: Update comments in Topology structures for attached devices to Atlas.(DCSG00061230)
 -WG 7.12 Alpha: LSA continues to be in debug mode when "./LSA -" executed for configuring LWM alert settings.(DCSG00028583)
 -When create or delete VD in LSA, VD information didn't refresh under LSA web in VMWare 6.7.(DCSG00068509)
 -WG: non Generic Icon shown for IT in CC page, typo in batch failure notification, no notification for premium feature key above 40 character.(DCSG00027350)
 -WG: LSA -console enters an infinite loop on entering a character/string as input.(DCSG00008008)
 -LSA upgrade fails from 7.10 patch RO to 7.12 RO with ./deleteOldVersion.sh: line 79: ((: 009: value too great for base (error token is "009") in SLES 12 SP4.(DCSG00014016)
 -Client: Schema changes for lanes.(DCSG00010703)
 -LSA does not allow the user to configure alert settings.(DCSG00031332)
 -WG: MR 7.12 : Arm SLIR3 version is shown empty in view server profile.(DCSG00008006)
 -LSA - AMD 2P Wave1 - Same RAID level migration throws an error in LSA if user is not adding/removing any drives.(DCSG00028267)
 -LSA GUI display empty page when launching the app.(DCSG00014599)
 -LSA Server: Handle new MFI status in LSA.(DCSG00031865)
 -fixed: updated LSA version.(DCSG00008023)
 -LSA Server: Add MRMonMsg project to the LSA solution.(DCSG00007928)
 -Fixed: lane width is displayed as unknown.(DCSG00035811)
 -Schema changes for lanes.(DCSG00010702)
 -On ARM server during LSA upgrade, ./deleteOldVersion.sh: line 53: LSIStorageAuthority: command not found error is observed.(DCSG00025403)
 -WG: lsa.exe -console fails to execute with LWM installed on windows machine.(DCSG00007461)
 -ARM Ubuntu: Linux Uninstallation leaving slpd process alive.(ARM Ubuntu: Linux Uninstallation leaving slpd process alive)
 -WG: Manual discovery of the ubantu server from windows gateway lists it as VMware server, issue related to search and adding already discovered server.(DCSG00010474)
 -Fixed: Added aarch64 detection code for linux.(DCSG00008022)
 -LSA Advanced Configuration does not work with controller is with RAID mode , Personality behavior=RAID-0.(DCSG00063716)
 -Even after LSA is uninstalled the LSA and Nginx port numbers are still busy, reinstallation requires using alternate free ports: Ubuntu.(DCSG00011517)
 -Address property Display mismatch for PD and Enclosure properties for MR and IT.(DCSG00017217)
 -LSA Server: External defect review:id=45919.(DCSG00007404)
 -For unconfigured bad drives, typo in Negotiated link speed & Drive speed in physical Drive properties page.(DCSG00007251)
 -Fixed: Resolved primary nic interface data population.(DCSG00010261)
 -LSA under Drives for IT controllers is showing selected elements 0 always.(DCSG00015834)
 -WG_7.12_LSA: Invalid VD size range notification is shown on entering VD capacity out of range.(DCSG00007446)
 -WG: Aero DBU Alpha(LSA): Select all snapdump --> deselect one of snapdump and then click on headline deselects all selected snapdumps.(DCSG00027305)
 -Fixed: missing span was not handled appropriately in DG health.(DCSG00027676)
 -WG: Mutliselect PD notification for IT controllers notifies user to select multiple Virtual Drive rows, clicking on FW version does not lead to FW update page.(DCSG00027320)
 -LSA crashes when clear drive operation performed.(DCSG00022528)
 -WG: during uninstallation of LSA from the control panel the publisher information is not shown in windows.(DCSG00042280)
 -Fixed: slpd didnt start durint startup.(DCSG00011426)
 -LSA Common: Handle events 610-613.(DCSG00008066)
 -Fixed: updated openssl library.(DCSG00010277)
 -WG:7.12:abort core dump seen for rekey operation on LSA..(DCSG00009381)
 -RWC3 Home Page Help Button Hyper Link is Broken.(DCSG00050748 Port Of Defect DCSG00057415)
 -WG: Copyright info needs to be updated from 2019 to 2020.(DCSG00068495 (Port Of Defect DCSG00068560))
 -DCSG00037620 (Port Of Defect DCSG00037685)
 -LSA Server: Resolving merge issues.(DCSG00032674 (Port Of Defect DCSG00032824))
 -LSA Readme file has to be updated for Aero controller support and proper open SLP web link..(DCSG00054273 (Port Of Defect DCSG00062969))
 -Add the language support matrix in to LSA readme.(DCSG00024412 (Port Of Defect DCSG00024705))
 -LSA IT : Not able to sort the drives based on drive "Model"..(DCSG00032171 (Port Of Defect DCSG00048474))
 -LSA getting hung while loading in windows 2019 OS on Stonyford server.(DCSG00058328 (Port Of Defect DCSG00058796))
 -LSA MR: VD(Raid5) status is showing as degraded, instead of offline..(DCSG00032167 (Port Of Defect DCSG00032180))
 -LSA show incorrect physical drive information, when drive push pull operation performed..(DCSG00026587 (Port Of Defect DCSG00026634))
 
 EnhancementRequests:
 -LSA Server:Add security-related compiling flags to LSA 3rd Party Components.(DCSG00010237)
 -Ubuntu support for RWC3.(DCSG00016264)
 -Enhance user notification about the unsecure connection.(DCSG00008000)
 -Linux LSA HSM based signing support.(DCSG00038899)
 -LSA Windows: Maintain the resource files across the build upgrade.(DCSG00021254)
 -Windows LSA HSM based signing support.(DCSG00038808)
 -API change to support 1. OEM specific UBM Back planes, and 2. Smart Battery state.(DCSG00040165)
 -Update MR API mr_drv.h to modify field for RTTRace_header.(DCSG00042985)
 -LSA Common:Add security-related compiling flags to LSA 3rd Party Components.(DCSG00010240)
 -API change OOB Self Diagnostics Design Improvements.(DCSG00054194)
 -LSA to handle the new error code populated by the SL IT.(DCSG00024064 (Port Of EnhancementRequest DCSG00024476))
 -DCSG00019108 (Port Of EnhancementRequest DCSG00019110).
 -DCSG00019108 (Port Of EnhancementRequest DCSG00019288).
 

007.010.016.000  - Moderate Impact
---------------
Defect:
 LSA MR: VD(Raid5) status is showing as degraded, instead of offline.(DCSG00032167)
 LSA IT : Not able to sort the drives based on drive "Model".(DCSG00032171)
 LSA does not display Virtual drive info for foreign configuration.(DCSG00035734 port of DCSG00035555)
 WG_7.12: On SLES 15 OS, After login, on doing some basic operations LSA, it redirects to 50x.html.(DCSG00026970 port of DCSG00022866)
 LSA 7.10 + Ubuntu Linux install issues.(DCSG00032287 port of DCSG00032286)
 Aero DBU alpha (LSA):LSA crashes when make jbod/UG performed on multiple drives with Schedular wrapper enabled.(DCSG00026968 port of DCSG00024414)
 nginx logs result in large disk space consumption.(DCSG00032285 port of DCSG00032280)
 SLES 15 Linux: Un-Installation is not removing the complete folder structure.(DCSG00027735 port of DCSG00023296)
 
EnhancementRequest Records Linked (4):
 New Event for firmware DMD handling
 StoreLib.h: Enhanced debug logging mechanism
 Storelib.h: Add new SL API SL_OOB_SET_TRANSPORT_TYPE to dynamically load SL in any oob mode
 API changes for Request to change all BBU messages to CacheVault.
 API changes needed for DPMstat support in MegaRAID SAS 3.5 controllers
 LSA 3rdParty :Add security-related compiling flags to LSA 3rd Party Components
 Automating Arm Builds


007.010.014.000 - Moderate Impact
---------------

Defects (277)
 - WG: Enclosure:Slot number is not displaying in Ascending or Descending order, if other columns are clicked first.(SCGCQ01874775)
 - Issues wrt the linux installer script(SCGCQ01879303)
 - WG: installing LSA on linux 64 bit machine throws an error " ‘/root/Desktop/LaunchLSA.desktop’: No such file or directory"(SCGCQ01897393)
 - IR3: Drive count is 0 and no PDs were listed in Controller console Page--> Drives Tab(SCGCQ01898255)
 - LSA Event ID 519 shows blank.(SCGCQ01901169)
 - Incorrect icon displayed along with "settings saved" message.(SCGCQ01905838)
 - LSA:Loading More data initially in BGOPS Progress bar in LSA and later Device ID disappears(SCGCQ01937373)
 - PH10 PA LSA is not launching after a upgrade from v007.009.002.000 to 007.009.003.000(SCGCQ01940193)
 - WG: No Action Successful notification shown on Drive erase(single Drive)(SCGCQ01941129)
 - LSA 7.9: Mismatch of sector size string between PD table and Group name(SCGCQ01942630)
 - LSA Server: LSA needs to Handle when controller is in safe Mode(SCGCQ01949074)
 - LSA is not launching after a upgrade from v007.009.002.000 to 007.009.003.000(SCGCQ01949090)
 - Linux binary not working.(SCGCQ01949665)
 - WG: String Changes related to VD operations, Filter blank box turn blue, expand backplane icon can be removed when drives=0(SCGCQ01960486)
 - Fixed: WG: LSA manage link speed pane does not provide any info to user on which port is connected/disconnected(SCGCQ01963966)
 - SmartCarrier Enclosure type shown as "vSES" in LSA(SCGCQ01965395)
 - : MRSA shows Bay Count as 255 under Enclosure / Backplane properties(SCGCQ01965427)
 - LSA:Add Logical drive Page give option to select"Cached IO" for an LD and Error message not Branding compliant(SCGCQ01965445)
 - LSA 7.9 alpha:issues pertaining to migration from degraded Unmpa R5 to R0(SCGCQ01966275)
 - LSA 7.9 Foreign config Import doesnt work correctly with Raid 1 VD(SCGCQ01966687)
 - WG:GUI issues:50x Html file,View server profile with no enclosure,View More of System messages, Restore Settings notification(SCGCQ01968404)
 - WG: GUI issues Pertaining to alignment of notification on scroll of LSA page(SCGCQ01968457)
 - WG: LSA fails with the empty status description on trying to change the personality in presence of snapdump(SCGCQ01969570)
 - Fixed: Can't Create 5 VDs R6 using 4 pds with AWB,ARA policy with different strip size(SCGCQ01970007)
 - WG: no success or failure message is shown on updating the drive secuirty key(SCGCQ01970452)
 - Port information missing under Enclosures List.(SCGCQ01972260)
 - LSA Server: Returning wrong status code as return value - Status Code and Description implementation(SCGCQ01972673)
 - Reference to BBU in Server profile page(SCGCQ01976904)
 - Shenandoah_MRSA: Listing SAS SSD drive while trying to migrate an array configured with HDD's.(SCGCQ01976926)
 - Logical drives are listed in the GUI when all the drives are pulled out(SCGCQ01976929)
 - LSA Server: Returning wrong status code as return value - Status Code and Description implementation(SCGCQ01977769)
 - Fixed: Added check for missing drive case(SCGCQ01978914)
 - Fixed: LSA stops responding after creating Vd with 4k Drives(SCGCQ01978965)
 - VD/HotSpare reference in Clear Configuration Confirmation popup-Regression(SCGCQ01979076)
 - Summary: Gateway LSA is not responding in SLES 12 64bit(SCGCQ01979137)
 - Error code is not displayed for DG add VD operation failure(SCGCQ01988209)
 - Modify array option available for Degraded R5 , Blank screen followed "0 drives" on removing drives(SCGCQ01988400)
 - Fixed: update Validation Check codes for the image file(SCGCQ01989969)
 - Aero A0: RWC3 does not show version of Selected Firmware Version for updating(SCGCQ01989970)
 - LSA 7.9:Secure using FDE option is not shown for VD(using OPAL(SCGCQ01993099)
 - Fixed: OS name for localhost is inconsistent with the Osname populated when discovered via slp(SCGCQ01994459)
 - LSA 7.9:Send Email functionality of LSA is not working.(SCGCQ01998245)
 - Fix: WG: Intance validation for Controller Get fails : MR Ventura(SCGCQ01998299)
 - WG: Instance validation for PD and Configuration service GET fails with " isSupportedByFW' & 'securityType' was unexpected(SCGCQ01998305)
 - Memory Leak issues LSA Build (7.009.007.00(SCGCQ02006229)
 - WG: Switching between view server profile and settings page would not load the view server profile(SCGCQ02007150)
 - WG: Enabling or disabling SSD guard fails with error code "1", Description: "SSD Guard Disable Failure (SCGCQ02009718)
 - LSA 7.9: Action successful notification is not seen for encrypting the DG(SCGCQ02010670)
 - LSA: Mismatch in Unconfigured Good string(SCGCQ02016646)
 - LSA: Patrol Read string display issue(SCGCQ02016879)
 - WG : LSA 7.9 Status code for Drive security disable message is showing same for StatusLevel 0 and 1(SCGCQ02018083)
 - Difference in naming of Array during Array creation(SCGCQ02019200)
 - WG: GUI issues pertaining to star/stop patrol read & remote discovery page(SCGCQ02019555)
 - Back-plane information showing as blank in server profile page.(SCGCQ02019592)
 - LSA 7.9:Clear config is successful when OS Pd and other PDs are in jbod state(SCGCQ02021372)
 - LSA : Updating FW pkg version is not shown during FW upgrade/downgrade.(SCGCQ02023284)
 - PH11 PA LSA - Attached Drive info not displayed under controller page(SCGCQ02023407)
 - LSA 7.10:Unsupported drives are displayed as UG under server profile page.(SCGCQ02030950)
 - LSA: LSA Crashes on updating firmware and doing OCR, not able to recover further(SCGCQ02032031)
 - WG: LSA manage link speed pane does not provide any info to user on which port is connected/disconnected(SCGCQ02032824)
 - Error message displayed for entering wrong password to unlock foreign VD/PD should be updated.(SCGCQ02034263)
 - PH11 PA - LSA IT - Copyright info needs to be updated(SCGCQ02034466)
 - Fixed: WG: Instance validation for Controller Get fails(SCGCQ02035158)
 - WG: mouse hover icon missing for the connected device property column in manage link speed pane(SCGCQ02035223)
 - WG:Unable to perform Enable SCSI Unmap operation when DHSP is removed from the VD.(SCGCQ02035226)
 - Shenandoah_Aero: LSA crash observed while trying to create more than maximum LD allowed(SCGCQ02035317)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02035322)
 - WG: Selected element count does not get updated after auto page refresh when VD expand operation is performed(SCGCQ02036089)
 -(SCGCQ02036091)
 - WG: wrong notification shown on trying to unlock a foreign FDE drive with wrong passphrase and then with correct passphrase(SCGCQ02036701)
 - Aero DBU PA1:LSA-Issue pertaining to add hotspare while creating Vd(SCGCQ02038235)
 - Cacheinit should not issue READ_AFTER_IMPORT dcmd id no foreign pd present.(SCGCQ02038386)
 - LSA - Patrol Read maxconcurrentpd count in LSA should be inline with FW(SCGCQ02040516)
 - MRSA: Crash when tried to flash corrupt firmware(SCGCQ02040739)
 - Shenandoah_MRSA: Warning message improvement when tried to delete LD formatted with File System(SCGCQ02042555)
 - LSA Client: MRSA: Crash when tried to flash corrupt firmware(SCGCQ02043781)
 - WG : LSA 7.10 Keyboard short cut keys are NOT there for Different pages of LSA Installation pages(SCGCQ02045646)
 - Fixed: OCR should trigger update of dual image components(SCGCQ02048856)
 - WG: Issues pertianing to set snapdump properties page--> enable disable snapdump and changing cache offload limit.(SCGCQ02048906)
 - WG: Incomplete foreign VD is seen when Clear foreign config is performed, incorrect status code on rescan after clear foreign(SCGCQ02049476)
 - WG:Securing JBOD option gets disabled if from list of JBODs selected even if one is unselected(SCGCQ02049479)
 - LSA displays one of the PD's is missing as part of foreign config even if all the PDs are connected(SCGCQ02049511)
 - WG: Few of VD and PD operations will not be usable in LSA without zooming out ((SCGCQ02049819(SCGCQ02049819)
 - WG: in presence of missing drive the select all and element count does not work properly in span drive tab(SCGCQ02050441)
 - WG 7.10:Advance controller info does not show whether energy pack is connected or not(SCGCQ02050502)
 - WG 7.10:Number of foreign config count is not updated if clear drive operation performed on a foreign pd.(SCGCQ02050579)
 - WG 7.10:Migration from r0 (31 pds(SCGCQ02050857)
 - Error and Warnings thrown while install/upgrade MRSA on SLES15(SCGCQ02053038)
 - WG: LSA notifications GUI issues & Other Hardware user info on expanding enclosure info, LSA conf file, Message_en file(SCGCQ02053156)
 - WG: UI Elements alignment for DG actions and Fixed action menu with lower resolution(SCGCQ02053167)
 - LSA Firmware package version shown as version in controller action page.(SCGCQ02053748)
 - LSA Simple configuration from main page shows blank when JBOD are present.(SCGCQ02053891)
 - Fixed: Last Vd size was not being checked for alignment(SCGCQ02058284)
 - Fixed: timestamp inside compressed file is not appropriate(SCGCQ02058485)
 - LSA capacity column sort not working in other Hardware Tab.(SCGCQ02058597)
 - Default Logical Drive name is showing as "VDName**" , while creating Logical drive through Simple Configuration(SCGCQ02062623)
 - WG: Element count not updated on selecting foreign drives and sorting Foreign drive list, it continues to show PD operations(SCGCQ02063630)
 - MRSA: LD Name discrepancy for 1 LD and 2 LDs without LD_Name during Array creation(SCGCQ02067043)
 - In presence of NVME drives, applying and Clearing filter and then sorting the drives results in incorrect PD list(SCGCQ02069473)
 -(SCGCQ02069524)
 -(SCGCQ02074686)
 - WG_7.10: Spacing alignments to be done in the VD setting page during the VD creation(SCGCQ02076790)
 - WG_7.10: While consistency check is in progress on VD, if we click pause progress bar is misaligned(SCGCQ02076792)
 - Fixed: check in place to create nvmeOnly disk group during migration(SCGCQ02076800)
 - WG: FDE foreign config after performing instant secure erase on one of the drive shows incomplete in LSA(SCGCQ02080536)
 - WG_7.10: Spell check and spacing issues in Latest LSA (007.010.003.000)(SCGCQ02081258)
 - "Drive Group list is empty" error message seen when multiple drives are assigned as DHSP to a VD, issue per(SCGCQ02081264)
 - Silent installation is NOT working on Ubuntu 16.04(SCGCQ02082129)
 - Download support Log not working.(SCGCQ02082514)
 - Aero (DBU PA3(SCGCQ02082524)
 - DG number displayed outside the box(SCGCQ02089434)
 - Aero DBU PA2(LSA(SCGCQ02091088)
 - WG: selected element count shown wrong on selecting PD list(including mising(SCGCQ02095469)
 - Fixed: missing pd info was leading to population of wrong candidate pds(SCGCQ02095494)
 - WG: LSA Lists drives of a type even if less for a raid level creation if user selects raid level from compare select(SCGCQ02096215)
 - Fixed: Changed build files to build client for ESXi(SCGCQ02096396)
 - WG: LSA snapdump files generated are only of 32 kb even if the actual snapdump file size is much higher than that(SCGCQ02100467)
 - WG: Filter options does not list NVMe drives in PD list of controller console page(SCGCQ02107270)
 - WG: extracting snapdump file using 7zip, user is notified regarding header error in etty file, spacingissue of text in OFU(SCGCQ02108538)
 - LSA - While doing RLM from R6 to R1, odd number of drives option is coming for R1(SCGCQ02108817)
 - Fix API changes done for NVMe readiness(SCGCQ02142981)
 - Add NVMe width comments to mr.h(SCGCQ02146846)
 - Fixed: changed the max drive value of R1 for cachecade drives(SCGCQ02169419)
 - LSA - AWB option is coming for CC VD with Rambler card while creating CC VD(SCGCQ02169687)
 - LSA Cache update for PD insert for it ctrls(SCGCQ02191080)
 - WG: LSA does not display the correct VD creation time in VD get URI response(SCGCQ01889478)
 - MRSA : NO option to go forward while configuring the VD`s if all drives are in JBOD.(SCGCQ01902964)
 - LSA 7.9: Display error for "OS name" when expand/minimize is performed.(SCGCQ01904365)
 - Fixed: Configuration service changed to accomadate allomixinSSD bit(SCGCQ01925161)
 -(SCGCQ01927978)
 - LSA 7.9:Changing server parameter in Configfile.json file to 2 , scheduler does not kick inn and LSA crashes(SCGCQ01930410)
 - LSA 7.9 PA:failure messange with description success on enabling/disabling scsi unmap feature.(SCGCQ01936667)
 - WG: After adding an VMware server manually to remote discovery page, the " GO to manage server page is not clickable"(SCGCQ01940852)
 - RWC3 Linux License Agreement and Desktop Shortcut Is for LSI instead of RWC3 (Windows RWC3 is okay(SCGCQ01942985)
 - Fixed: Foreign drives are not considered as configured & which leads to a mismatch in JBODconversion count during VD creation(SCGCQ01943388)
 - LSA Client: GWT Popup panels are morphing the GWT fixed panels(SCGCQ01943617)
 - LSA 7.9: Mismatch in "Unconfigured drives and replace drive" count.(SCGCQ01944392)
 - WG: VD creation page does not show VD count and capacity of VD that can be created using unmap drive(SCGCQ01952143)
 - LSA 7.9:Unable to start instanst secure erase operation on multiple Pds when scheduler is on.(SCGCQ01955160)
 - WG: Issues pertaining to Settings page(SCGCQ01956683)
 - WG: After creating VD from server summary page opens empty JBOD conversion page, issue pertaining sector size in filter(SCGCQ01957078)
 - LSA 7.9 alpha:Disable data protection option is seen for non-secured & secured VD in presence of locked foreign PD(SCGCQ01960300)
 - LSA 7.9 alpha:Incomplete foreign found after unlocking the Locked foreign config during the Reconstruction.(SCGCQ01962216)
 - LSA 7.9 alpha :The error code 69636 is seen without view more option when pause on CC operation is performed twice(SCGCQ01971576)
 - WG:LSA displays the snapdump count in hex value, GUI issues in snapdump pane(SCGCQ01973964)
 - MRSA event for Drive erase abort is coming blank in "View Event log" for event ID 421(SCGCQ01976894)
 - LSA 7.9:when multiple Vds are added on the existing DG, there is inconsistency in the Vd name(SCGCQ01978171)
 - Fixed: "All the listed drives cannot be mixed" displayed while creation of R0 with "select all" option.(SCGCQ01979083)
 - fixed: LSA doesnt consider Copyback state while counting configured pds.(SCGCQ01979598)
 - LSA : Port details are missing in drive removal/insert events.(SCGCQ01979793)
 - Fixed: missing Event description for new events was pausing LSA(SCGCQ01980570)
 - LSA 7.9:LSA Gray page is seen when multiple VDs of multiple DGs are deleted.(SCGCQ01983080)
 - MRSA : Copyback progress details is not proper in BGI progress tab.(SCGCQ01996577)
 - (SCGCQ02003711: Add default HTTPS to RWC3(SCGCQ02003711)
 - WG: GUI issues : Drive Security text on Hover, system messages clickable text, bell button notification(SCGCQ02006538)
 - “404 Not Found” seen on upgrading Snap4 GA to OEM Builds and later removing and installing new build(SCGCQ02016688)
 - LSA 7.10:Covert button of the Jbod table is activated and flickers when more than eligible count pds are selected.(SCGCQ02024507)
 - WG: No VD or PD details shown for progress operation in VMware(SCGCQ02028695)
 - Shenandoah_Aero: LSA crash observed while trying to create more than maximum LD allowed(SCGCQ02031517)
 - WG : LSA Cache Offload Limit value change was not changing without manual refresh(SCGCQ02043843)
 - WG: LSA view event log list the Portmap as '0' instead of '08' for scsiType=0 (ie PDs)(SCGCQ02045715)
 - LSA: Authenticated User group is given Read only privileges after adding Authenticated Users to full_access_groups.(SCGCQ02045735)
 - WG: LSA does not show the details of the current profile when there is only one profile supported(SCGCQ02045758)
 - WG: System LSA monitor event logs has junk characters(SCGCQ02049034)
 - WG: Path information for PD reset event is empty in event logs (event id : 268(SCGCQ02049577)
 - LSA: Domain login for administrator fails with "Error code:49 Invalid credentials".(SCGCQ02049807)
 - WG 7.10:if VD count is above limit and VD capacity is changed, LSA allows user to create VD which fails(SCGCQ02050533)
 - LSA Simple Configuration for R6 fails with error.(SCGCQ02053837)
 - LSA service crashing in ubuntu(SCGCQ02061370)
 - Linux Build is always picking old library(SCGCQ02061380)
 - Aero DBU PA2(LSA(SCGCQ02065672)
 - Incorrect number of slots is displayed for UBM U.2X2 Vses Backplane in LSA.(SCGCQ02069871)
 - Fixed: Calculation to get possible range for RLM(SCGCQ02070841)
 - Aero DBU PA2(LSA(SCGCQ02074776)
 - WG_7.10:In the Error code:118 description, Spacing alignments to be done.(SCGCQ02076794)
 - WG_7.10: SAS address is shown for PCIe (NVME(SCGCQ02076924)
 - Wide port info is not displayed for physical drive under connector name for Backplane attached drives.(SCGCQ02076933)
 - LSA: VD actions performed using storcli not reflected under LSA's Virtual drive tab(SCGCQ02078435)
 - LSA: Read_only_access group users are given administrator privileges(SCGCQ02078614)
 - WG: User is notified to select the Drive group even if VD and PD tab of the DG is clicked(SCGCQ02080553)
 - RWC3 Windows Readme contains IR3 controllers under supported controllers list(SCGCQ02081038)
 - During LSA upgrade some of the old build files are not removed in Ubuntu(SCGCQ02082116)
 - WG 7.10: wrong health status of a gateway server seen when discovered from same gateway server.(SCGCQ02084545)
 - WG:LSA Direct agent or LWM installation from main package creates desktop shorcut in linux(SCGCQ02084636)
 - WG 7.10:Scheduler wrapper does not kick in for enable security operation(SCGCQ02085660)
 - Fixed: FDE and Opal mixing shouldn't be allowed(SCGCQ02086784)
 - Migration from R1 Vd(4 drives)(SCGCQ02087362)
 - Element action pane border incomplete during single PD selection, user name/password blue box alignment(SCGCQ02091191)
 - Issue pertaining to failure notification(SCGCQ02095408)
 - Fixed: FW upgrade issues with Aero FW files(SCGCQ02097971)
 - Fixed: R00 max pd limit is changed to be aligned with fw requirement(SCGCQ02108807)
 - LSA wrongly treats "MaxAHCIDev" as "Max SATA supported drives" in profile info.(SCGCQ02119031)
 - Fixed: Cachecade VD creation diaglog doesnt populate Raid levels(SCGCQ02142026)
 - "Remove drives" option should not come if user is doing RLM from R6 with 3 drives to R5(SCGCQ02184393)
 - WG: LSA manage link speed pane does not provide any info to user on which port is connected/disconnected(SCGCQ01512320)
 - LSA needs to Handle when controller is in safe Mode(SCGCQ01838234)
 - MRSA : MRSA shows the logout option in drop down menu .(SCGCQ01902913)
 - LSA 7.9: Unable to enter password while adding mail server authentication.(SCGCQ01933819)
 - LSA 7.9 :Status error description for schedular operation is not mapped to the proper device ID.(SCGCQ01940978)
 - WG: NO PD info is shown for foreign configuration(SCGCQ01942159)
 - WG: Instance Secure Erase is not giving any action indication(SCGCQ01942452)
 - WG:Remove icon for manually added server not shown in manage server page, Signin should be disabled when login in progress(SCGCQ01960469)
 - Scheduler API call in not working in standalone mode of installation(SCGCQ01961390)
 - LSA 7.9 alpha: Error code 69642 is seen when disable/enable unmap operation is performed on Unmap VD.(SCGCQ01963097)
 - fixed: logout of indirect agent causing gateway session to expire(SCGCQ01969806)
 - WG: All the events to Vmware are coming as information(SCGCQ01973905)
 - LSA 7.9: Incorrect critical message displayed for Offline PD.(SCGCQ01979150)
 - Fixed: Updated curl library for Linux OS(SCGCQ01979794)
 - LSA 7.9: Re-scan button is disabled after GHS import.(SCGCQ01982953)
 - LSA 7.9:FDE HDDs are assigned as DHSP for an encrypted OPAL VD(SCGCQ01982973)
 - Status reports as failed although firmware is updated successfully(SCGCQ01983031)
 - MR 7.9 PA: LSA Win: 7.9_PA-007.009.007.000 Fails to display JBOD, StorCLI works fine(SCGCQ01994803)
 - LSA does not show failure or success notification when clear configuration is performed.(SCGCQ01996512)
 - WG: Instance Validation failed for Event history GET(SCGCQ01998296)
 - LSA - Selected firmware version displayed as blank during update firmware(SCGCQ02034485)
 - LSA: Administrators User group is given Read only privileges after adding Users to Administrators group.(SCGCQ02048915)
 -(SCGCQ02048923)
 - Client changes for review-30 schema compliance(SCGCQ02062850)
 - Aero DBU PA2(LSA(SCGCQ02065575)
 - LSA Windows Readme: Update the LSA Windows Read me with the enhanced Silent installation instructions(SCGCQ02070840)
 - WG: snapdump downloaded after host triggered snapdump is not in zip file format(SCGCQ02084515)
 - WG 7.10: LSA crashes when generate snapdump or dowload snap dump operations are performed on direct agent(SCGCQ02094537)
 - GUI css issues with update firmware panel and snapdump actions(SCGCQ02094845)
 - Spacing issues seen while converting a drive from JBOD to UG(SCGCQ02095422)
 - WG:Enclosure ID and Device ID display inconsistency in SS page and CC page, Configure options in SS page alignment issues(SCGCQ02095855)
 - LSA couldn't install successful in RHEL 8.0 without OpenSLP installed(SCGCQ02103116)
 - Capacity sorting is not working in presence of TB drive in the PD list of VD creation.(SCGCQ02107449)
 - Snap dump trigger time format ends with Z character.(SCGCQ02184362)
 - WG: with loop back SMTP Ip, only the test email is received to broadcom mail id, able to add duplicate email id to email tab(SCGCQ01880101)
 - Fixed: when SasSata-mixing-policy is set to false vd creation options are not getting populated(SCGCQ01880184)
 - WG 7.8: Dedicatedhotspare and Replace missing drive tables are combined in LSA(SCGCQ01888233)
 - LSA 7.8: Incorrect VD capacity size displayed during VD creation(SCGCQ01897176)
 - LSA 7.9: Mismatch in the alignment of server list.(SCGCQ01904368)
 - Update firmware version link not clickable in Server Landing Page(SCGCQ01905815)
 - After converting JBOD drives to UG drives, "action successful" message not displayed and incorrect PD actions listed(SCGCQ01927915)
 - LSA Client: In Remote Discovery page, "servers" call is being made twice(SCGCQ01932106)
 - Incorrect tab listener in login page.(SCGCQ01932725)
 - LSA 7.9: "Personality management" page do not close automatically after launch of "Schedule consistency check" page.(SCGCQ01933812)
 - Fixed: clear and generate snap dump feature should not be displayed if snap dump is disabled(SCGCQ01936663)
 - WG: Memory Leak issue with LSA build : 5.035.000.000(SCGCQ01937263)
 - Clear configuration message not indicating about discards pinned cache(SCGCQ01951802)
 - WG:GUI issues:Controller health text,system message bar,download log, scheduler operation failure & JBOD to UG notifications(SCGCQ01968459)
 - Fixed: LSA 7.9:In presence of 32 GHSPs, advance configuration option is leading to configurable page on iMR card(SCGCQ01969524)
 - LSA_7.9: Issue pertaining to PD offline operation on multiple PD's of a VD(SCGCQ01969611)
 - LSA_7.9: Status code and description are not clear during Unconfigured Bad to Unconfigured Good operation.(SCGCQ01972681)
 - WG: JBOD to UG conversion popup does not show error notification in case there is an OS drive, fails with 400ok though(SCGCQ01973688)
 - WG: Enabling and disabling the alarm multiple times shows error message without error code number(SCGCQ01973701)
 - LSA Server: Returning wrong status code as return value - Status Code and Description implementation(SCGCQ01974131)
 - MR 7.9 Alpha: readForeignCfg: error reading refPd=c!!! aborting operation(SCGCQ01993611)
 - LSA locate time inaccurate(SCGCQ02038270)
 - Aero DBU PA2(LSA(SCGCQ02065617)
 - No response observed when tried to import Foreign LDs which results is reaching MAX LDs(SCGCQ02082982)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102427)
 - 7.10-LSA: Event ID 457 description ends junk character.(SCGCQ02184221)
 -(SCGCQ01878801)
 - LSA 7.9: Incorrect value accepted during PD locate and wrong Icon displayed in IE when compared to Chrome.(SCGCQ01901766)
 - LSA server profile shows IT-IR storlib versions.(SCGCQ01901771)
 - LSA 7.9: Incorrect Filter message displayed, wrong message after max vd and multiple grammatical errors in Licence document.(SCGCQ01901773)
 - LSA 7.9: Server search list no more displayed if the user press enter or move the cursor.(SCGCQ01905850)
 - PH10 PA - LSA - Logout option not presented when drop down arrow is clicked(SCGCQ01934763)
 - WG: Status code description is not proper(SCGCQ01942172)
 - LSA 7.9: After converting JBOD drives to UG drives, "action successful" message not displayed and incorrect PD actions listed(SCGCQ01949787)
 - LSA 7.9 alpha:LSA Status code enhancements - Individual operations related issues(SCGCQ01961403)
 - WG: GUI issues: 404 due to unavailable image, VMware login error notification when server down, FW update notification(SCGCQ01968407)
 - WG: VD options are not getting updated after the expanding the VD on selecting the VD while VD expansion is in progress(SCGCQ01973705)
 - LSA PR (SCGCQ01907025: Existing administrator authorization fails with Error code:49: invalid credentials.(SCGCQ02023562)
 - WG_7.10: Enclosure location shows blank for the NVME drives(SCGCQ02076920)
 - LSA - AWB option is coming for CC VD with Rambler card when user try to modify VD properties if CC VD goes offline/degraded(SCGCQ02184389)
 - WG: Table formatting is not proper in controller console page(SCGCQ01875668)
 - Fixed: Adding more than 1 vd on a hole & adding more than 1 vds on existing DG fails in LSA(SCGCQ01940161)
 - when clear drive operation is aborted on foreign Pds, the Pds are seen as UG as well listed under DG(SCGCQ01944435)
 - Fixed: Download DA/SA server report when downloaded remotely from Gateway(SCGCQ01969625)
 - MRSA: Enclosure count updated wrong in Server profile page(SCGCQ01976923)
 - For 7.10 LSA with max VD configuration, with foreign configuration present LSA unable to import or reject or proper message should displayed. Can you please look into this issue.(SCGCQ02184326)
 - LSA 7.9: Select and un-select button does not work after minimizing the tab(SCGCQ01978952)
 - Fixed: Blank page shown on trying to login 2nd time VMware using Manage server page(SCGCQ02035380)
 - LSA : Getting wrong data about max number of PD support for R6 while doing RLM(SCGCQ02184391)
 - SCGCQ01134787: GUI’s are required to be localized for the following languages: English, French, Italian, German, Spanish, and Japanese(SCGCQ01840448 port of SCGCQ01134787)
 - Security Standalone requirements for LSA Server code changes(SCGCQ01854924 port of SCGCQ01399720)
 - Megacell Status Support - Phase2 (Caching and Controller health Status(SCGCQ01857649 port of SCGCQ01598200)
 -(SCGCQ01868298 port of SCGCQ01564366)
 - Megacell Status Support - Phase2 (Caching and Controller health Status(SCGCQ01869716 port of SCGCQ01598139)
 - IR3: Drive count is 0 and no PDs were listed in Controller console Page--> Drives Tab(SCGCQ01962269 port of SCGCQ01898255)
 - WG: After adding an VMware server manually to remote discovery page, the " GO to manage server page is not clickable"(SCGCQ01963211 port of SCGCQ01940852)
 - LSA - Not able to import other foreign configs if user have SED drive which is in foreign(SCGCQ01963213 port of SCGCQ01937406)
 - MRSA : NO option to go forward while configuring the VD`s if all drives are in JBOD.(SCGCQ01963214 port of SCGCQ01902964)
 - Clear configuration message not indicating about discards pinned cache(SCGCQ01963766 port of SCGCQ01951802)
 - WG: LSA manage link speed pane does not provide any info to user on which port is connected/disconnected(SCGCQ01963971 port of SCGCQ01512320)
 - when clear drive operation is aborted on foreign Pds, the Pds are seen as UG as well listed under DG(SCGCQ01965222 port of SCGCQ01944435)
 - Scheduler API call in not working in standalone mode of installation(SCGCQ01965612 port of SCGCQ01961390)
 - RWC3 Linux License Agreement and Desktop Shortcut Is for LSI instead of RWC3 (Windows RWC3 is okay(SCGCQ01971208 port of SCGCQ01942985)
 - LSA 7.9 alpha:Incomplete foreign found after unlocking the Locked foreign config during the Reconstruction.(SCGCQ01971235 port of SCGCQ01962216)
 - LSA 7.9 Foreign config Import doesnt work correctly with Raid 1 VD(SCGCQ01972651 port of SCGCQ01966687)
 - Fixed: missing Event description for new events was pausing LSA(SCGCQ01991449 port of SCGCQ01980570)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx(SCGCQ02000919 port of SCGCQ01929667)
 - (SCGCQ01993697: MR7.9 Alpha: RWC3 (LSA(SCGCQ02002118 port of SCGCQ01993697)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx(SCGCQ02007219 port of SCGCQ01929667)
 - (SCGCQ01993697: MR7.9 Alpha: RWC3 (LSA(SCGCQ02015378 port of SCGCQ01993697)
 - WG: Enabling or disabling SSD guard fails with error code "1", Description: "SSD Guard Disable Failure "(SCGCQ02016686 port of SCGCQ02009718)
 - Memory Leak issues LSA Build (7.009.007.00(SCGCQ02030825 port of SCGCQ02006229)
 - PH11 PA LSA - Attached Drive info not displayed under controller page(SCGCQ02031020 port of SCGCQ02023407)
 - LSA Client : Trigger and Download Snap Dump from application(SCGCQ02032043 port of SCGCQ01917087)
 - LSA 7.9:Clear config is successful when OS Pd and other PDs are in jbod state(SCGCQ02032206 port of SCGCQ02021372)
 - WG: No Action Successful notification shown on Drive erase(single Drive(SCGCQ02032617 port of SCGCQ01941129)
 -(SCGCQ02034407 port of SCGCQ02030621)
 -(SCGCQ02034409 port of SCGCQ02030621)
 - LSA 7.9:Send Email functionality of LSA is not working.(SCGCQ02034511 port of SCGCQ01998245)
 - PH11 PA - LSA IT - Copyright info needs to be updated(SCGCQ02035246 port of SCGCQ02034466)
 - WG:Unable to perform Enable SCSI Unmap operation when DHSP is removed from the VD.(SCGCQ02036726 port of SCGCQ02035226)
 - Logical drives are listed in the GUI when all the drives are pulled out(SCGCQ02042290 port of SCGCQ01976929)
 - Memory Leak issues LSA Build (7.009.007.00(SCGCQ02042291 port of SCGCQ02006229)
 - LSA 7.9:LSA Gray page is seen when multiple VDs of multiple DGs are deleted.(SCGCQ02042976 port of SCGCQ01983080)
 - LSA_7.9: Issue pertaining to PD offline operation on multiple PD's of a VD(SCGCQ02043600 port of SCGCQ01969611)
 - LSA locate time inaccurate(SCGCQ02043617 port of SCGCQ02038270)
 - LSA locate time inaccurate(SCGCQ02043619 port of SCGCQ02038270)
 - Fixed: Can't Create 5 VDs R6 using 4 pds with AWB,ARA policy with different strip size(SCGCQ02043629 port of SCGCQ01970007)
 - Fixed: "All the listed drives cannot be mixed" displayed while creation of R0 with "select all" option.(SCGCQ02043631 port of SCGCQ01979083)
 - Fixed: when SasSata-mixing-policy is set to false vd creation options are not getting populated(SCGCQ02043632 port of SCGCQ01880184)
 - LSA Client: MRSA: Crash when tried to flash corrupt firmware(SCGCQ02043796 port of SCGCQ02043781)
 - WG: Instance Secure Erase is not giving any action indication(SCGCQ02044624 port of SCGCQ01942452)
 - WG: VD options are not getting updated after the expanding the VD on selecting the VD while VD expansion is in progress(SCGCQ02044809 port of SCGCQ01973705)
 - Issues wrt the linux installer script(SCGCQ02044832 port of SCGCQ01879303)
 - LSA 7.9:when multiple Vds are added on the existing DG, there is inconsistency in the Vd name(SCGCQ02044903 port of SCGCQ01978171)
 - WG: After creating VD from server summary page opens empty JBOD conversion page, issue pertaining sector size in filter(SCGCQ02046361 port of SCGCQ01957078)
 - No help option available for Megacell option whenever it calls for “Needs Attention” in LSA(SCGCQ02050529 port of SCGCQ02022983)
 - LSA - Patrol Read maxconcurrentpd count in LSA should be inline with FW(SCGCQ02053882 port of SCGCQ02040516)
 - LSA 7.9: Incorrect Filter message displayed, wrong message after max vd and multiple grammatical errors in Licence document.(SCGCQ02055506 port of SCGCQ01901773)
 -(SCGCQ02055834 port of SCGCQ01878801)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02055865 port of SCGCQ02035322)
 - (SCGCQ02003711: Add default HTTPS to RWC3(SCGCQ02057603 port of SCGCQ02003711)
 - LSA Standalone - enhanced authentication/authorization (Windows(SCGCQ02064849 port of SCGCQ01984624)
 - LSA Server: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02067442 port of SCGCQ02045048)
 - LSA Windows Readme: Update the LSA Windows Read me with the enhanced Silent installation instructions(SCGCQ02070858 port of SCGCQ02070840)
 - LSA: Read_only_access group users are given administrator privileges(SCGCQ02080158 port of SCGCQ02078614)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02084533 port of SCGCQ02035322)
 - Fixed: Calculation to get possible range for RLM(SCGCQ02087354 port of SCGCQ02070841)
 - Fixed: Calculation to get possible range for RLM(SCGCQ02093538 port of SCGCQ02070841)
 - Fixed: Allowed Simple config parameters are not displayed(SCGCQ02094990 port of SCGCQ02076799)
 - LSA is not showing PD Connector information properly with passive backaplane(SCGCQ02096769 port of SCGCQ02096766)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102495 port of SCGCQ02102427)
 - Application Crash when tried to create a LD with 15 character length(SCGCQ02113222 port of SCGCQ02112041)
 - LSA wrongly treats "MaxAHCIDev" as "Max SATA supported drives" in profile info.(SCGCQ02119286 port of SCGCQ02119031)
 - Application Crash when tried to create an LD with 15 character length(SCGCQ02121748 port of SCGCQ02111930)
 - WG 7.11: Simple configuration fails when multiple vds are created.(SCGCQ02125582 port of SCGCQ02125538)
 - Configuration options is not getting updated when we change the personality(SCGCQ02154818 port of SCGCQ02124500)
 - Only 1 drive is displayed although more than 1 drive has opted for Dedicated drive(SCGCQ02154840 port of SCGCQ02113971)
 - Aero DBU PA5(LSA): Secure jbod option is not shown for the FDE capable jbod drive in LSA(SCGCQ02162725 port of SCGCQ02149233)
 - LSA service/Nginx service is stopping after few hours and WebGUI is not responding in RHEL 8.0 OS(SCGCQ02172192 port of SCGCQ02151342)
 - LSA Aero IT: LSA installation with "start from now" option is throwing error code:9098 in event logs.(SCGCQ02172199 port of SCGCQ02121896)
 - Event ID 610 and 611 are empty(SCGCQ02172244 port of SCGCQ02166100)
 - Generic LSA w/MRSA backend (Snap 3(SCGCQ01818695 port of SCGCQ01532391)
 - IML event customization (Mesa Verde(SCGCQ01837799 port of SCGCQ01625911)
 - Dual Firmware Image Support on Controller Flash for Recovery(SCGCQ01847635 port of SCGCQ01320454)
 - LSA : Dqueue logs need to be fetched in smaller chunks by the applications(SCGCQ01860906 port of SCGCQ01571368)
 - SSD WEAR GAUGE Support(SCGCQ01891668 port of SCGCQ01890543)
 - OPAL drives fail to import when entering wrong security key then right security key after power cycle(SCGCQ01915862 port of SCGCQ01905192)
 - WG: Enclosure:Slot number is not displaying in Ascending or Descending order, if other columns are clicked first.(SCGCQ01963764 port of SCGCQ01874775)
 - LSA Client: GWT Popup panels are morphing the GWT fixed panels(SCGCQ01965636 port of SCGCQ01943617)
 - WG: LSA services crashes while adding the manually discovered VMware server to the manage server list(SCGCQ01967858 port of SCGCQ01918692)
 - In JBOD personality LSA service getting stopped when user change JBOD to UG(SCGCQ01971507 port of SCGCQ01971368)
 - (SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01990298 port of SCGCQ01856350)
 - (SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01990346 port of SCGCQ01829895)
 - (SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ02001873 port of SCGCQ01856350)
 - LSA: LSA Crashes on updating firmware and doing OCR, not able to recover further(SCGCQ02034499 port of SCGCQ02032031)
 - Shenandoah_MRSA: Listing SAS SSD drive while trying to migrate an array configured with HDD's.(SCGCQ02042096 port of SCGCQ01976926)
 - LSA 7.9:Secure using FDE option is not shown for VD(using OPAL)(SCGCQ02042097 port of SCGCQ01993099)
 - Cacheinit should not issue READ_AFTER_IMPORT dcmd id no foreign pd present.(SCGCQ02042292 port of SCGCQ02038386)
 - WG 7.8: Dedicatedhotspare and Replace missing drive tables are combined in LSA(SCGCQ02043598 port of SCGCQ01888233)
 - fixed: LSA doesnt consider Copyback state while counting configured pds.(SCGCQ02043630 port of SCGCQ01979598)
 - Shenandoah_Aero_LSA: LSA crashes while initiating OCR on A0 controller(SCGCQ02043856 port of SCGCQ02000446)
 - LSA 7.9 alpha:Disable data protection option is seen for non-secured & secured VD in presence of locked foreign PD(SCGCQ02043858 port of SCGCQ01960300)
 -(SCGCQ02043859 port of SCGCQ01927978)
 - WG: GUI issues: 404 due to unavailable image, VMware login error notification when server down, FW update notification(SCGCQ02044679 port of SCGCQ01968407)
 - WG: no success or failure message is shown on updating the drive secuirty key(SCGCQ02044688 port of SCGCQ01970452)
 - MRSA: Crash when tried to flash corrupt firmware(SCGCQ02045015 port of SCGCQ02040739)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02055880 port of SCGCQ02035322)
 - Status reports as failed although firmware is updated successfully(SCGCQ02058472 port of SCGCQ01983031)
 - LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online".(SCGCQ02081267 port of SCGCQ01838943)
 - LSA: VD actions performed using storcli not reflected under LSA's Virtual drive tab(SCGCQ02084746 port of SCGCQ02078435)
 - NVMe Drive interface type should be shown as "NVMe" instead of "PCIe"(SCGCQ02100198 port of SCGCQ02096718)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102571 port of SCGCQ02102427)
 - Fixed: Snap dump file(SCGCQ02105149 port of SCGCQ02080184)
 - WG 7.11:Jbod Locked foreign config details are empty under foriegn configuration operation.(SCGCQ02112529 port of SCGCQ02112203)
 - WG: LSA incorrectly notifies "Incomplete or Non-Importable foreign configuration found" instead of max supported configuratio(SCGCQ02162724 port of SCGCQ02149353)
 - WG: LSA shows the same connector for both backplane and enclosure in properties pane(SCGCQ02179358 port of SCGCQ02167855)
 - Drive capacities displayed should match the HPE drive capacity labels.(SCGCQ01869701 port of SCGCQ01246226)
 - Support newly added Sanitize event for cache update.(SCGCQ01869717 port of SCGCQ01740786)
 - WG: with loop back SMTP Ip, only the test email is received to broadcom mail id, able to add duplicate email id to email tab(SCGCQ01918643 port of SCGCQ01880101)
 -(SCGCQ01925516 port of SCGCQ01714322)
 - LSA needs to Handle when controller is in safe Mode(SCGCQ01963207 port of SCGCQ01838234)
 - WG: Memory Leak issue with LSA build : 5.035.000.000(SCGCQ01965387 port of SCGCQ01937263)
 - LSA Server: LSA needs to Handle when controller is in safe Mode(SCGCQ01967491 port of SCGCQ01949074)
 - WG MR 7.7 alpha:Lsa does not update the PD(part of r0 volume(SCGCQ01970440 port of SCGCQ01752969)
 - LSA 7.9 alpha:issues pertaining to migration from degraded Unmpa R5 to R0(SCGCQ01971232 port of SCGCQ01966275)
 - In JBOD personality LSA service getting stopped when user change JBOD to UG(SCGCQ01974074 port of SCGCQ01971368)
 - PH11 PA - LSA IT - Copyright info needs to be updated(SCGCQ02035247 port of SCGCQ02034466)
 - LSA Client: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02067299 port of SCGCQ02044922)
 - RWC3 Windows Readme contains IR3 controllers under supported controllers list(SCGCQ02082904 port of SCGCQ02081038)
 - WG 7.10: LSA crashes when generate snapdump or dowload snap dump operations are performed on direct agent(SCGCQ02099466 port of SCGCQ02094537)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02103244 port of SCGCQ02102427)
 - Fixed: R00 max pd limit is changed to be aligned with fw requirement(SCGCQ02116793 port of SCGCQ02108807)
 - LSA - While doing RLM from R6 to R1, odd number of drives option is coming for R1(SCGCQ02118270 port of SCGCQ02108817)
 -(SCGCQ02154813 port of SCGCQ02142063)
 - Fixed: parity disk count was missing in algorithm to calculate minimum VD(SCGCQ02154869 port of SCGCQ02139246)
 - WG: LSA does not update on Clearing the config from server summary page in presence of degraded config(SCGCQ02160137 port of SCGCQ02154073)
 - LSA - upgrade installshield(SCGCQ02164387 port of SCGCQ02087375)
 - Download Server Report – change this to Download Support Log and Remove Download Diagnostics(SCGCQ01824401 port of SCGCQ01388152)
 - LSA No Login (HPE Snap 3 SOW(SCGCQ01840451 port of SCGCQ01512600)
 - Sanitize Support (HPE SNAP 3(SCGCQ01857424 port of SCGCQ01564367)
 - IML event customization (Mesa Verde(SCGCQ01868281 port of SCGCQ01625911)
 - LSA is allowing to delete OS VD.(SCGCQ01923557 port of SCGCQ01873420)
 - LSA - Not able to import other foreign configs if user have SED drive which is in foreign(SCGCQ01942179 port of SCGCQ01937406)
 - WG: VD creation page does not show VD count and capacity of VD that can be created using unmap drive(SCGCQ01962278 port of SCGCQ01952143)
 - WG: LSA services crashes while adding the manually discovered VMware server to the manage server list(SCGCQ01967919 port of SCGCQ01918692)
 - WG: Instance validation for PD and Configuration service GET fails with " isSupportedByFW' & 'securityType' was unexpected(SCGCQ01998976 port of SCGCQ01998305)
 - (SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ02001889 port of SCGCQ01829895)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx(SCGCQ02007218 port of SCGCQ01929667)
 - (SCGCQ02003711: Add default HTTPS to RWC3(SCGCQ02007520 port of SCGCQ02003711)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02053863 port of SCGCQ02035322)
 - Fixed: WG: Instance validation for Controller Get fails(SCGCQ02062148 port of SCGCQ02035158)
 - WG: snapdump downloaded after host triggered snapdump is not in zip file format(SCGCQ02089526 port of SCGCQ02084515)
 - Fixed: Calculation to get possible range for RLM(SCGCQ02093240 port of SCGCQ02070841)
 - LSA couldn't install successful in RHEL 8.0 without OpenSLP installed(SCGCQ02105326 port of SCGCQ02103116)
 - RHEL8- LSA reports warnings during Service restart after reboots, remote discovery page does not list any server other server(SCGCQ02159794 port of SCGCQ02144606)
 - : Support PCI Slot and Serial Number in(SCGCQ01822600 port of SCGCQ01351434)
 - MRSA:Default strip size should be 64KB for SSD(SCGCQ01825959 port of SCGCQ01406706)
 - Change the word data protection to Data Integrity Field(SCGCQ01839302 port of SCGCQ01827434)
 - Expander support for LSA(SCGCQ01839611 port of SCGCQ01372657)
 - (SCGCQ01681996: Copy back option should not prompt for already copyback progress PD.(SCGCQ01840438 port of SCGCQ01681996)
 - Drive capacities displayed should match the HPE drive capacity labels.(SCGCQ01847392 port of SCGCQ01134783)
 -(SCGCQ01943786 port of SCGCQ01932181)
 - fixed: logout of indirect agent causing gateway session to expire(SCGCQ01996636 port of SCGCQ01969806)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx(SCGCQ02000918 port of SCGCQ01929667)
 - Shenandoah_Aero_LSA: LSA crashes while initiating OCR on A0 controller(SCGCQ02012079 port of SCGCQ02000446)
 - MR 7.9 Alpha: readForeignCfg: error reading refPd=c!!! aborting operation(SCGCQ02015391 port of SCGCQ01993611)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102497 port of SCGCQ02102427)
 - LSA is using old PDL for send Feedback option(SCGCQ02133579 port of SCGCQ02133392)
 - WG: Making an offline drive of a DG to online does not work in controller health pane, no POST call for same is initiated(SCGCQ02144596 port of SCGCQ02139321)
 - (SCGCQ01399721: Hercules :HPE: Security Standalone requirements for LSA Linux 32/64 bit Installer changes(SCGCQ01827380 port of SCGCQ01399721)
 - Support PCI Slot and Serial Number in Mesa Verde(SCGCQ01839058 port of SCGCQ01349491)
 - Capacity Unit Changes for VD in LSA Client from GB to GIB(SCGCQ01859426 port of SCGCQ01708968)
 -(SCGCQ01864209 port of SCGCQ01763927)
 - LSA 7.8: Unable to launch LSA from different web server port after LSA upgrade.(SCGCQ01904366 port of SCGCQ01901758)
 - IML event customization (Mesa Verde(SCGCQ01837623 port of SCGCQ01601601)
 - Megacell Status Support (SNAP3(SCGCQ01868328 port of SCGCQ01566234)
 -(SCGCQ01869156 port of SCGCQ01320455) -
 - WG 7.11:Enable scsi unmap checkbox at advance config page is grayed out when enable/disable operation is performed.(SCGCQ02154812 port of SCGCQ02118865)
 - Security Standalone requirements for LSA Server code changes(SCGCQ01854929 port of SCGCQ01399722)
 - Expander support for LSA(SCGCQ01855600 port of SCGCQ01376077)
 - LSA Not allowing to clear/Import foreign configuration.(SCGCQ01869616 port of SCGCQ01849749)
 - Capacity Unit Changes for VD in LSA Server(SCGCQ01869745 port of SCGCQ01708881)

EnhancementRequests (35)
 - Enhance Status Code and Status description(SCGCQ01825960)
 - LSA Internal Status code and Description(SCGCQ01850884)
 -(SCGCQ01949651)
 - Branding tool and Health (OS eventing(SCGCQ01960398)
 - Ubuntu LSA support(SCGCQ02042072)
 - LSA Server: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02045048)
 - Branding tool and Health (OS eventing(SCGCQ02045972)
 - API changes for NVMe speed and width changes(SCGCQ02053667)
 - API changes for linkconfig interface(SCGCQ02053671)
 - Change the parent directory name to "HPEMRSA" in the windows(SCGCQ02055912)
 - Implement Changes for LSA Light weight agent On ESXi 64 bit Platform(SCGCQ02066385)
 - Add disableOffloadNum field in MR_SNAPDUMP_PROPERTIES struct(SCGCQ02125252)
 - API changes for a better presentation of Atlas to tools(SCGCQ02149380)
 - Snap Dump ClearAll Method logging event(SCGCQ02157359)
 -(SCGCQ02162699)
 - Create an event for DDF config clear failed event.(SCGCQ02173513)
 - WG: LSA "Feedback" UI enhancements(SCGCQ01401503)
 - LSA Client : Trigger and Download Snap Dump from application(SCGCQ01917087)
 - Implemented: Allow user to generate snap-dump in firmware and download it(SCGCQ01917294)
 - Client: Ubuntu LSA support(SCGCQ02042121)
 - LSA Client: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02044922)
 - 64 Bit SLIR3 library to Support for VMWARE ESXi 6.7+(SCGCQ02048704)
 - MR API: Add support bits for currentSpeed and clkMode(SCGCQ02132334)
 - Adding NVACHE messages indicate when SLC format has started and completed.(SCGCQ02137048)
 - Add new topology device type for Atlas switch(SCGCQ02150637)
 - LSA need to show complete Serial Number and Model Name for NVMe drives(SCGCQ01920105)
 - LSA Standalone - enhanced authentication/authorization (Windows(SCGCQ01984624)
 - SSD WEAR GAUGE Support(SCGCQ01890543)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx(SCGCQ01929667)
 - 64 Bit SLIT library Support for VMWARE ESXi 6.7+(SCGCQ02019271)
 - LSA: SSD WEAR GAUGE Support(SCGCQ01890612)
 - MRSA One Click Support Client support(SCGCQ01949650)
 - LSA Server: Scheduler changes to fit with latest LSA status code(SCGCQ01857843)
 - Enhance Status Code and Status description(SCGCQ01868342)
 - LSA Server: Aero FW simplification - Changes for disable least latency mode(SCGCQ01944689)

005.047.000.000 - Moderate Impact
---------------

Defects:
 -WG:Memory leak issues when the system is not idle ( Running the GUI suite when the memory leak test is in progress).(SCGCQ01680714)
 -Fixed: nvme is allowed to mix with sas /sata.(SCGCQ01762948)
 -WG:[intermittent] LSA page goes blank if we click on Drive tab and then immediately click on view serer profile.(SCGCQ01747490)
 -WG MR 7.7 alpha:Lsa does not update the PD(part of r0 volume) status once the PD is made online from offline(SCGCQ01752969)
 -WG MR 7.7 al:LSA allows to create simple configuration in presence of Unconfigured bad drive and rest of the drives in jbod.(SCGCQ01763742)
 -WG MR 7.7 alpha: LSA displays wrong connector & path info for drives when enclosure is connected in wide port (x8 connection).(SCGCQ01764794)
 -WG: JBOD conversion popup appears multiple times after converting all the drives to UG and clicking on Continue button.(SCGCQ01737550)
 -LSA locate time inaccurate.(SCGCQ02038270)
 -LSA PR SCGCQ01907025: Existing administrator authorization fails with Error code:49: invalid credentials.(SCGCQ02023562)
 -LSA: Authenticated User group is given Read only privileges after adding Authenticated Users to full_access_groups..(SCGCQ02045735)
 -LSA: VD actions performed using storcli not reflected under LSA's Virtual drive tab.(SCGCQ02078435)
 -LSA: Read_only_access group users are given administrator privileges.(SCGCQ02078614)
 -RWC3 Windows Readme contains IR3 controllers under supported controllers list.(SCGCQ02081038)
 -Fixed: R00 max pd limit is changed to be aligned with fw requirement.(SCGCQ02108807)
 -LSA - While doing RLM from R6 to R1, odd number of drives option is coming for R1.(SCGCQ02108817)
 -LSA wrongly treats "MaxAHCIDev" as "Max SATA supported drives" in profile info..(SCGCQ02119031)
 - LSA installation failed on SLES15.(SCGCQ01784699 port of SCGCQ01760620)
 - LSA needs proper message for max config import.(SCGCQ01789100 port of SCGCQ01763411)
 - MRSA Snap 4 : Alpha : LSA provides option of performing an RLM operation on Degraded VD, which fails.(SCGCQ01789156 port of SCGCQ01731931)
 - LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode.(SCGCQ01716625 port of SCGCQ01716622)
 - WG: LSA allows user to replace a drive of a DG with drive on which drive clear is already in progress, GUI issues in popup.(SCGCQ01810649 port of SCGCQ01803341)
 - MR7.7: Removal of UNMAP support for JBOD.(SCGCQ01813086 port of SCGCQ01813078)
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config.(SCGCQ01816649 port of SCGCQ01686080)
 - MR7.6: LSA crashed with a mouse click on VD.(SCGCQ01816428 port of SCGCQ01641760)
 - LSA needs proper message for max config import.(SCGCQ01813925 port of SCGCQ01764977)
 - C480-M5: LSA downloaded event log needs better decoding.(SCGCQ01828830 port of SCGCQ01321211)
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events.(SCGCQ01826237 port of SCGCQ01761830)
 - LSA-4.1 : Array details are shown in LSA for the partial foreign config .(SCGCQ01850405 port of SCGCQ01818828)
 - Tape drive state is blank when connected with 9400-8E card from LSA drives tab.(SCGCQ01851980 port of SCGCQ01851906)
 - SCGCQ01841280: Before importing foreign CC VD, model number of SSD is not coming in LSA.(SCGCQ01851919 port of SCGCQ01841280)
 - UG LSA 7.8 PA2:Incomplete foreign VD is seen when Clear foreign config is performed.(SCGCQ01851155 port of SCGCQ01849681)
 - LSA Not allowing to clear/Import foreign configuration.(SCGCQ01860933 port of SCGCQ01849749)
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01880125 port of SCGCQ01874487)
 - LSA login to ESXi 6.x servers fails in SLES 15 OS..(SCGCQ01880123 port of SCGCQ01876091)
 - handling the session management.(SCGCQ01892868 port of SCGCQ01829897)
 - WG: VMware server takes too long to discover in remote discovery page : nearly 20 minutes.(SCGCQ01891168 port of SCGCQ01889547)
 - Handling the set text mechanism in client.(SCGCQ01886532 port of SCGCQ01850387)
 - Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016.(SCGCQ01897181 port of SCGCQ01841473)
 - Fixed: Crash when pressing back button after logout.(SCGCQ01892905 port of SCGCQ01865309)
 - LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap.(SCGCQ01897266 port of SCGCQ01818960)
 - LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online" .(SCGCQ01898344 port of SCGCQ01838943)
 - fixed: LSA fails to create RAID 10 with large number of drives.(SCGCQ01901767 port of SCGCQ01833469) 
 - Fixed: unblock LSA login on ESXi 6.7 U1.(SCGCQ01901774 port of SCGCQ01866289)
 - Change tools to report drives attached to HBAs as JBOD instead of UGOOD.(SCGCQ01898263 port of SCGCQ01802344)
 - Fixed: Auto Span Adjust with having >64 disks is not correct..(SCGCQ01901754 port of SCGCQ01827404)
 - CC VD creation option is coming in LSA when the CC VD (SATA SSD) is in foreign config.(SCGCQ01897144 port of SCGCQ01817275)
 - Update the Windows Server 2019 OS name in LSA.(SCGCQ01897178 port of SCGCQ01866322)
 - Remove un printable characters from LSA log.(SCGCQ01901769 port of SCGCQ01901760)
 - Server: LSA GUI Not Updating Security Key Info.(SCGCQ01897099 port of SCGCQ01761801)
 - OPAL drives fail to import when entering wrong security key then right security key after power cycle.(SCGCQ01915861 port of SCGCQ01905192)
 - [CISCO]LSA shows previously set security key (M3g@raid) during importing secured foreign config JBOD (TCG Enterprise SED).(SCGCQ01921581 port of SCGCQ01878346)
 - LSA fails to start initialization on EPD if it has DDF.(SCGCQ01921583 port of SCGCQ01849522)
 - (SCGCQ01921684 port of SCGCQ01841361)
 - MR7.8 Foreign import from 7.7 to 7.8 with unmap VD and non unmap DHS does not alert user with a critical message/event.(SCGCQ01921836 port of SCGCQ01876230)
 - LSA 7.8:LSA provides Instant secure erase option for Locked UG BAD drives..(SCGCQ01904075 port of SCGCQ01893304)
 - LSA 7.8: Unable to launch LSA from different web server port after LSA upgrade..(SCGCQ01904345 port of SCGCQ01901758)
 - .(SCGCQ01920699 port of SCGCQ01808698)
 - LSA: Ventura B0: BIOS Flashing Failure Observed in EFI Storcli and Multiple Tries Causes UART Unresponsive.(SCGCQ01921839 port of SCGCQ01829669)
 - (SCGCQ01921842 port of SCGCQ01803373SCGCQ01803373: WG: LSA service crashes on downloading support logs in case of Linux 64 bit OS)
 - LSA does not show Secure Erase option for foreign secured JBOD drive-CLI works(SCGCQ01920701 port of SCGCQ01916249)
 - .(SCGCQ01920924 port of SCGCQ01818618)
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon.(SCGCQ01921819 port of SCGCQ01856350)
 - WG: LSA provides option of Secure using FDE if non encrypted r1 VD with secure drive is assigned with DHSP,.(SCGCQ01915812 port of SCGCQ01906914)
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01921592 port of SCGCQ01829895)
 - LSA 7.8:Import option is given for the Incomplete foreign VD.(SCGCQ01921678 port of SCGCQ01829895)
 - LSA 7.8:Import option is given for the Incomplete foreign VD.(SCGCQ01921678 port of SCGCQ01865420)
 - LSA is allowing to delete OS VD.(SCGCQ01921689 port of SCGCQ01873420)
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01921919 port of SCGCQ01856350)
 - WG: LSA allows to remove the data drive during the RLM from single drive R0 and allows migrate to R0 with no drives DESCRIPTION OF ISSUE(SCGCQ01921580 port of SCGCQ01823858)
 - Fixed: Advance configuration operation should be greyed out if max pds are already configured(SCGCQ01922015 port of SCGCQ01850445)
 -WG: LSA does not notify user on OS VD present if multiple VDs are selected and with non OS VD is selected first(SCGCQ01928961 port of SCGCQ01926674 )
 - LSA Server: Populate the Drive Sector Size while reading the LD MFI command.(SCGCQ01930623 port of SCGCQ01926876)
 - WG: VMware server takes too long to discover in remote discovery page : nearly 20 minutes.(SCGCQ01961510 port of SCGCQ01889547)
 - Summary: Gateway LSA is not responding in SLES 12 64bit(SCGCQ01980553 port of SCGCQ01979137)
 - Cannot use Special Characters in Domain Name for LSA Login(SCGCQ01789161 port of SCGCQ01745768)
 - Optimize the operation areas of UI to add “on demand” call and increase the performance(SCGCQ01792860 port of SCGCQ01746630)
 - Add sorter on individual panel's header(SCGCQ01792967 port of SCGCQ01614993)
 - SCGCQ01761197: Handle Progress events without initiating further api call from Client.(SCGCQ01793020 port of SCGCQ01761197)
 - LSA Server: Enhance view server profile(SCGCQ01793119 port of SCGCQ01613889)
 - Add a way to move from Server / Controller dashboard to Login / Remote Server Discovery Page.(SCGCQ01793314 port of SCGCQ01760616)
 - LSA Client : GUI User Interface to display snap dump details and download snap dump.(SCGCQ01788693 port of SCGCQ01788622)
 -GUI Performance improvement by reducing the GUI binary size.(SCGCQ01791174 port of SCGCQ01484572)
 - WG: Clicking on help links anywhere in LSA page for VMware leads to "404-not found" page.(SCGCQ01791205 port of SCGCQ01594101)
 - LSA Server: Client Logging(SCGCQ01793221 port of SCGCQ01745790)
 - Enhance Action menu of individual and group element(SCGCQ01793250 port of SCGCQ01606850)-
 - Add Select All / Un-Select All option to dashboard tables.(SCGCQ01793004 port of SCGCQ01580899)
 - SCGCQ01761197: Handle Progress events without initiating further api call from Client.(SCGCQ01793081 port of SCGCQ01761224)
 - WG MR 7.7 Alpha:Foreign configuration pane does not show details for foreign dedicated hotspare drive.(SCGCQ01798297 port of SCGCQ01745770)
 - Use scheduler call for heavy operations Part 2.(SCGCQ01792861 port of SCGCQ01746649)
 - SCGCQ01583133: Inconsistency of login dialog box in Manageserver page and Remote discovery page(SCGCQ01793098 port of SCGCQ01583133)
 - Fixed: LSA allows the user to attempt a 3 drive RAID6 VD creation (via RAID60).(SCGCQ01798511 port of SCGCQ01687523)
 - SCGCQ01631835: WG: error log and Access log consume entire OS file system space (6.3 GB and 2.6 GB respectively)(SCGCQ01798635 port of SCGCQ01631835)
 - LSA: SnapDump Implementation(SCGCQ01788680 port of SCGCQ01786658)
 - Enhance Properties panel of Individual elements.(SCGCQ01792093 port of SCGCQ01613898)
 - Handle Progress events without initiating further api call from Client.(SCGCQ01792974 port of SCGCQ01761196)
 - LSA Client Logging.(SCGCQ01792995 port of SCGCQ01752841)
 - LSA Client: Enhance view server profile(SCGCQ01793196 port of SCGCQ01613529)
 - LSA: SnapDump Implementation.(SCGCQ01793838 port of SCGCQ01786658)
 - (SCGCQ01798366 port of SCGCQ01628367)
 - Implemented: LSA: Disable Cached IO option during VD creation(SCGCQ01798387 port of SCGCQ01697006)
 - LSA Server: Optimize the operation areas of UI to add “on demand” call and increase the performance.(SCGCQ01793279 port of SCGCQ01745789)
 - Activity to check-in Auto-BST files to 7.8 streams.(SCGCQ01794950 port of SCGCQ01793057)
 - SCGCQ01595244: WG: issues pertaining to lsa logs file generation in VMware.(SCGCQ01798451 port of SCGCQ01595244)
 - Adding filters to the PD and VD table.(SCGCQ01625154 port of SCGCQ01614984)
  - MRSA Snap 4 : Alpha : LSA provides option of performing an RLM operation on Degraded VD, which fails.(SCGCQ01798299 port of SCGCQ01731931)
 - WG: Enclosure position is not shown in Progress bar PD details for any enclosure above position index=1 as well as event logs.(SCGCQ01801670 port of SCGCQ01794642)
 - LSA does not update the VD status when Migration is performed from r5(3drives)to r1(2drives).(SCGCQ01818637 port of SCGCQ01803743)
  - LSA 502 Bad gateway is seen when Prepare for removal is performed on 5 drives at a time.(SCGCQ01818638 port of SCGCQ01809413)
 - Adding filters to the PD and VD table.(SCGCQ01807941 port of SCGCQ01614984)
 - Implementation of LW Agent Related Back-end changes.(SCGCQ01801403 port of SCGCQ01591705)
 - Add SCSI Unmap property at PD level.(SCGCQ01813071 port of SCGCQ01732785)
 - SCGCQ01680714: WG:Memory leak issues when the system is not idle ( Running the GUI suite when the memory leak test is in progress).(SCGCQ01818554 por of SCGCQ01680714)
 - WG: Duplicate PD entires of replace Drive listed in PD list of controller console page on sorting the PD list more than twice.(SCGCQ01803785 port of SCGCQ01794631)
 - WG: View more properties pane is overlapped by the progress bar if the progress info is in expanded state.(SCGCQ01803986 port of SCGCQ01763142)
- MR7.7: Removal of UNMAP support for JBOD.(SCGCQ01813180 port of SCGCQ01813078)
 - LSA does not give expand option to perform OCE when one among 2vds is deleted under a DG.(SCGCQ01818631 port of SCGCQ01803722)
 - Unable to import foreign secured VDs with different security key.(SCGCQ01818678 port of SCGCQ01670139)
 - LSA needs proper message for max config import.(SCGCQ01813926 port of SCGCQ01764977)
 - MR7.6: LSA crashed with a mouse click on VD.( SCGCQ01819577 port of SCGCQ01641760)
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config.(SCGCQ01822126 port of SCGCQ01686080)
 -.(SCGCQ01824435 port of SCGCQ01317424)
 -.( SCGCQ01827729 port of SCGCQ01808698)
 - Change tools to report drives attached to HBAs as JBOD instead of UGOOD.(SCGCQ01837518 port of SCGCQ01802344)
 - handling the session management.(SCGCQ01841323 port of SCGCQ01829897)
 - LSA PD slot numbering doesn't not display as ascending order by default(SCGCQ01415337 port of SCGCQ01406115)
 - LSA : Stale entries are coming in DG tab when the VD (failed) is in foreign config(SCGCQ01838336 port of SCGCQ01818953)
 - CC VD creation option is coming in LSA when the CC VD (SATA SSD) is in foreign config(SCGCQ01838335 port of SCGCQ01817275)
 - Cannot use Special Characters in Domain Name for LSA Login(SCGCQ01837786 port of SCGCQ01745768)
 - LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap(SCGCQ01838449 port of SCGCQ01818960)
 - WG: JBOD conversion popup appears multiple times after converting all the drives to UG and clicking on Continue button.(SCGCQ01839325 port of SCGCQ01737550)
 - Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016(SCGCQ01845011 port of SCGCQ01841473)
 - WG:Typo event id : 233, Convert button should get disabled when JBOD to UG Conversion in progress, discrepancy in host icons(SCGCQ01848661 port of SCGCQ01840475)
 - WG MR 7.7 al:LSA allows to create simple configuration in presence of Unconfigured bad drive and rest of the drives in jbod(SCGCQ01847352 port of SCGCQ01763742)
 - LSA Client: Improving visible / working area on elements tab(SCGCQ01839616 port of SCGCQ01837412)
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01879301 port of SCGCQ01874487)
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events(SCGCQ01830499 port of SCGCQ01761830)
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events(SCGCQ01830498 port of SCGCQ01761830)
 - Drive status not displayed in Other Hardware tab(SCGCQ01855592 port of SCGCQ01849636)
 - Fixed: unblock LSA login on ESXi 6.7 U1(SCGCQ01874490 port of SCGCQ01866289)
 - WG:Typo event id : 233, Convert button should get disabled when JBOD to UG Conversion in progress, discrepancy in host icons.(SCGCQ01864285 port of SCGCQ01840475)
 - Tape drive state is blank when connected with 9400-8E card from LSA drives tab.(SCGCQ01852072 port of SCGCQ01851906)
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS..(SCGCQ01869568 port of SCGCQ01829895)
 - LSA Not allowing to clear/Import foreign configuration..(SCGCQ01860931 port of SCGCQ01849749)
 - LSA Client : 7.8 Coverity defects fix.(SCGCQ01865174 port of SCGCQ01837314)
 - Fixed: Auto Span Adjust with having >64 disks is not correct..(SCGCQ01855872 port of SCGCQ01827404)
 - LSA is allowing to delete OS VD.(SCGCQ01883000 port of SCGCQ01873420)
 - Implementation of LW Agent Related Back-end changes.(SCGCQ01801314 port of SCGCQ01591705)
 - LSA is allowing to delete OS VD.(SCGCQ01906734 port of SCGCQ01873420)
 - WG: Software licensing agreement for linux RWC3 build is of Generic Channel(SCGCQ01905909 port of SCGCQ01886563)
 - LSA 7.8: Controller actions menu, action successful message are misplaced and Progress bar and event log info overlaps.( SCGCQ01906795 port of SCGCQ01893511)
 - MR LSA 7.7 : When user has flashed the controller FW for IT card, reboot system message is disappearing within few seconds(SCGCQ01893311 port of SCGCQ01761269)
 -LSA: Ventura B0: BIOS Flashing Failure Observed in EFI Storcli and Multiple Tries Causes UART Unresponsive.(SCGCQ01890993 port of SCGCQ01829669)
 -.(SCGCQ01914269 port of SCGCQ01906844)
 - LSA 7.8: Controller actions menu, action successful message are misplaced and Progress bar and event log info overlaps.(SCGCQ01914265 port of SCGCQ01893511)
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01921950 port of SCGCQ01856350)
 - IR3: Drive count is 0 and no PDs were listed in Controller console Page--> Drives Tab.(SCGCQ01962269 port of SCGCQ01898255)
 - WG: After adding an VMware server manually to remote discovery page, the " GO to manage server page is not clickable"(SCGCQ01963211 port of SCGCQ01940852)
 - LSA - Not able to import other foreign configs if user have SED drive which is in foreign(SCGCQ01963213 port of SCGCQ01937406)
 - MRSA : NO option to go forward while configuring the VD`s if all drives are in JBOD.(SCGCQ01963214 port of SCGCQ01902964)
 - Clear configuration message not indicating about discards pinned cache(SCGCQ01963766 port of SCGCQ01951802)
 - when clear drive operation is aborted on foreign Pds, the Pds are seen as UG as well listed under DG(SCGCQ01965222 port of SCGCQ01944435)
 - Scheduler API call in not working in standalone mode of installation(SCGCQ01965612 port of SCGCQ01961390)
 - LSA 7.9 alpha:Incomplete foreign found after unlocking the Locked foreign config during the Reconstruction.(SCGCQ01971235 port of SCGCQ01962216)
 - WG: Enclosure:Slot number is not displaying in Ascending or Descending order, if other columns are clicked first.(SCGCQ01963764 port of SCGCQ01874775)
 - LSA Client: GWT Popup panels are morphing the GWT fixed panels(SCGCQ01965636 port of SCGCQ01943617)
 - WG: LSA services crashes while adding the manually discovered VMware server to the manage server list(SCGCQ01967858 port of SCGCQ01918692)
 - In JBOD personality LSA service getting stopped when user change JBOD to UG(SCGCQ01971507 port of SCGCQ01971368)
 - LSA needs to Handle when controller is in safe Mode(SCGCQ01963207 port of SCGCQ01838234)
 - WG: Memory Leak issue with LSA build : 5.035.000.000(SCGCQ01965387 port of SCGCQ01937263)
 - LSA Server: LSA needs to Handle when controller is in safe Mode(SCGCQ01967491 port of SCGCQ01949074)
 - LSA 7.9 alpha:issues pertaining to migration from degraded Unmpa R5 to R0(SCGCQ01971232 port of SCGCQ01966275)
 - WG: VD creation page does not show VD count and capacity of VD that can be created using unmap drive(SCGCQ01962278 port of SCGCQ01952143)
 - LSA 7.9 Foreign config Import doesnt work correctly with Raid 1 VD.(SCGCQ01972651 port of SCGCQ01966687)
 - SCGCQ01993697: MR7.9 Alpha: RWC3 (LSA) Uninstall Error: "Option “-x” is deprecated" w/ Linux RHEL 7.6.(SCGCQ02002118 port of SCGCQ01993697)
 - (CSETActivity) - LSA 7.9:Clear config is successful when OS Pd and other PDs are in jbod state.(SCGCQ02032206 port of SCGCQ02021372)
 -.(SCGCQ02034407 port of SCGCQ02030621)
 - LSA locate time inaccurate(SCGCQ02043617 port of SCGCQ02038270)
 - Fixed: when SasSata-mixing-policy is set to false vd creation options are not getting populated(SCGCQ02043632 port of SCGCQ01880184)
 - WG: Instance Secure Erase is not giving any action indication(SCGCQ02044624 port of SCGCQ01942452)
 - WG: VD options are not getting updated after the expanding the VD on selecting the VD while VD expansion is in progress.(SCGCQ02044809 port of SCGCQ01973705)
 - LSA 7.9:when multiple Vds are added on the existing DG, there is inconsistency in the Vd name(SCGCQ02044903 port of SCGCQ01978171)
 - Logical drives are listed in the GUI when all the drives are pulled out(SCGCQ02042290 port of SCGCQ01976929)
 - Memory Leak issues LSA Build (7.009.007.00)(SCGCQ02042291 port of SCGCQ02006229)
 - LSA 7.9:LSA Gray page is seen when multiple VDs of multiple DGs are deleted.(SCGCQ02042976 port of SCGCQ01983080)
 - LSA_7.9: Issue pertaining to PD offline operation on multiple PD's of a VD(SCGCQ02043600 port of SCGCQ01969611)
 - Fixed: Can't Create 5 VDs R6 using 4 pds with AWB,ARA policy with different strip size(SCGCQ02043629 port of SCGCQ01970007)
 - Fixed: "All the listed drives cannot be mixed" displayed while creation of R0 with "select all" option.(SCGCQ02043631 port of SCGCQ01979083)
 - LSA Client: MRSA: Crash when tried to flash corrupt firmware(SCGCQ02043796 port of SCGCQ02043781)
 - Issues wrt the linux installer script(SCGCQ02044832 port of SCGCQ01879303)
 - WG: After creating VD from server summary page opens empty JBOD conversion page, issue pertaining sector size in filter(SCGCQ02046361 port of SCGCQ01957078)
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ02001873 port of SCGCQ01856350)
 - Shenandoah_MRSA: Listing SAS SSD drive while trying to migrate an array configured with HDD's.(SCGCQ02042096 port of SCGCQ01976926)
 - Cacheinit should not issue READ_AFTER_IMPORT dcmd id no foreign pd present.(SCGCQ02042292 port of SCGCQ02038386)
 - WG 7.8: Dedicatedhotspare and Replace missing drive tables are combined in LSA(SCGCQ02043598 port of SCGCQ01888233)
 - fixed: LSA doesnt consider Copyback state while counting configured pds.(SCGCQ02043630 port of SCGCQ01979598)
 - LSA 7.9 alpha:Disable data protection option is seen for non-secured & secured VD in presence of locked foreign PD(SCGCQ02043858 port of SCGCQ01960300)
 -(SCGCQ02043859 port of SCGCQ01927978)
 - WG: GUI issues: 404 due to unavailable image, VMware login error notification when server down, FW update notification(SCGCQ02044679 port of SCGCQ01968407)
 - WG: no success or failure message is shown on updating the drive secuirty key(SCGCQ02044688 port of SCGCQ01970452)
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ02001889 port of SCGCQ01829895)
 - SCGCQ02003711: Add default HTTPS to RWC3(SCGCQ02007520 port of SCGCQ02003711)
 - fixed: logout of indirect agent causing gateway session to expire(SCGCQ01996636 port of SCGCQ01969806)
 - MR 7.9 Alpha: readForeignCfg: error reading refPd=c!!! aborting operation(SCGCQ02015391 port of SCGCQ01993611)
 - LSA Client : Trigger and Download Snap Dump from application(SCGCQ02032043 port of SCGCQ01917087)
 - WG: No Action Successful notification shown on Drive erase(single Drive), Application Version shown as undefined for VMware(SCGCQ02032617 port of SCGCQ01941129)
 - LSA 7.9:Send Email functionality of LSA is not working.(SCGCQ02034511 port of SCGCQ01998245)
 - LSA 7.9:Secure using FDE option is not shown for VD(using OPAL) when Drive security is enabled.(SCGCQ02042097 port of SCGCQ01993099)
 - Shenandoah_Aero_LSA: LSA crashes while initiating OCR on A0 controller(SCGCQ02043856 port of SCGCQ02000446)
 - MRSA: Crash when tried to flash corrupt firmware(SCGCQ02045015 port of SCGCQ02040739)
 - PH11 PA - LSA IT - Copyright info needs to be updated(SCGCQ02035247 port of SCGCQ02034466)
 - LSA Windows Readme: Update the LSA Windows Read me with the enhanced Silent installation instructions(SCGCQ02053863 port of SCGCQ02035322)
 - Fixed: WG: Instance validation for Controller Get fails(SCGCQ02070858 port of SCGCQ02070840)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02084533 port of SCGCQ02035322)
 - Fixed: Calculation to get possible range for RLM(SCGCQ02093538 port of SCGCQ02070841)
 - WG: snapdump downloaded after host triggered snapdump is not in zip file format(SCGCQ02089526 port of SCGCQ02084515)
 - Fixed: Calculation to get possible range for RLM(SCGCQ02093240 port of SCGCQ02070841)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102571 port of SCGCQ02102427)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02103244 port of SCGCQ02102427)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102497 port of SCGCQ02102427)
 - WG 7.10: LSA crashes when generate snapdump or dowload snap dump operations are performed on direct agent(SCGCQ02099466 port of SCGCQ02094537)
 
EnhancementRequest:
 -Update candidate drive list for VD creation when UNMAP/FDE etc Exist.(SCGCQ01879211)
 -Aero None-Mode implementation.(SCGCQ01871350)
 -Add CTRL_SB_SOFT_SECURE_MODE event to indicate soft secure mode.(SCGCQ01965721)
 -LSA Client: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog.(SCGCQ02044922)
 -LSA Server: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02045048)
 -LSA Standalone - enhanced authentication/authorization (Windows).(SCGCQ01984624)
 - Increase in MR_PD_INFO.name length to 32 characters.(SCGCQ02079068)
 -Better error message for certain unmap operations.(SCGCQ02111563)
 - MR Windows IOCTL Error codes to Application added to MR API.(SCGCQ02103183)
 - API change to support NVMe Passthrough over OOB.(SCGCQ02035295)
 - API change to support new DCMD for consolidated device list.(SCGCQ02037158)
 - Customer needs to generate and extract the On-demand based debug data both for MR and iMR..(SCGCQ02000566)
 - Modification in MR_SNAPDUMP_TRIGGER_TYPE enum value.(SCGCQ02030653)
 - Reword event log messages as it creates unnecessary panic..(SCGCQ02013675)
 - Add New Generic OOB API To Read ROC Temp, Drive Temp, Drive Type, Drive Protocol and status through OOB BMC.(SCGCQ01940661)
 - Add a bit for atomic descriptor capable.(SCGCQ01965047)
 - Additional details about spare.(SCGCQ02033538)
 - API changes for Lane Margining.(SCGCQ01921241)
 - Introduced new controller bit.(SCGCQ01985474)
 - Add MFI STAT and MR Event for Secure Boot indicating fw dl was not allowed due to an existing pending key change.(SCGCQ02103973)
 - Driver parameter bit for support of tool box cmd.(SCGCQ02002119)
 - API change to support new DCMD for consolidated device list.(SCGCQ02016723)
 - .(SCGCQ01740789)
 
 
004.189.000.000 - Moderate Impact
---------------

 -(SCGCQ01351380) 
 - WG: Physical Drives tab should be aligned in center for Advanced Configuration.(SCGCQ01440777) 
 - Fixed: settings in configuration service API is inconsistent with other applciations(SCGCQ01518134) 
 - LSA WG Fury IT: Fury Device ID is showing as 00 instead of 0x0097 in controller properties logs.(SCGCQ01534444) 
 - SCGCQ01539326: [UNMAP]MR7.6 Unmap/WriteSame: AEN's are not generated when unmap capability gets disabled or enabled on a VD.(SCGCQ01539326) 
 - LSA Client 7.6: SPAN drives order is not maintained(SCGCQ01539355) 
 - Client: LSA should handle the not empty check for enclousre field for the physicalDevices response(SCGCQ01555968) 
 - IT-FURY-PH16:LSA-4.126.0.0-Fully Populated Enclosure S/N is "NA" and shown correctly after few drive removals.(SCGCQ01563352) 
 - SCGCQ01565134: IT-Ventura-PH7:LSA-4.126.0.0- FW update fails with error "File size Exceeds 16MB".(SCGCQ01565134) 
 - WG : Server detail is getting populated twice when user is using local IP (127.0.0.1(SCGCQ01565327) 
 - WG: During VD Creation on Simple Configuration, Clicking more than Once on the Finish Button is giving a Wrong Message.(SCGCQ01569262) 
 - WG: Copyright info is shown as 2017 instead of 2018(SCGCQ01571088) 
 - WG:Pop Up scroll missing in case there are more number of VDs to add while setting patrol read properties & Schedule CC(SCGCQ01571089) 
 - WG: User is notified to that multiselect PD/VD displays the properties but it is not supported(SCGCQ01571095) 
 - IT-FURY-PH16:LSA-SATA NCQ bit is always shown as disabled(SCGCQ01571261) 
 - LSA is not responding if online state is changed to offline(SCGCQ01571453) 
 - SCGCQ01571863: WG: LSA installation/uninstallation on linux does not notify the user on success or failure(SCGCQ01571863) 
 - Fixed: Windows OS details were reported as VMware details in Manual Search(SCGCQ01571874) 
 - WG: LSA wrapper indicates the progress of operations appears to be clickable while there is nothing user can select from list(SCGCQ01573087) 
 - SCGCQ01575706: WG:LSA installation exits on invalid option for selecting range of LSA events, it asks for retry with options listed again(SCGCQ01575706) 
 - SCGCQ01575999: FURY-PH16:LSA-Model Number is getting truncated for ST3000DM001,Hitachi HDS723020BLA642 models.(SCGCQ01575999) 
 - WG: the string 'status' is displayed multiple times after searching the server for manual addition(SCGCQ01577707) 
 - WG: LSA allows to replace HDD missing drive with SSD UG drive, fails with Partial Success.0 Successful;1 Failed notification(SCGCQ01577769) 
 - fixed: logout causing unexpected behavior during end cim connection for vmware systems(SCGCQ01578248) 
 - LSA Server: Removal of Additional Carriage Returns and Line feeds in tty log file(SCGCQ01579290) 
 - WG: Error message on a failed VD creation is displayed outside the allocated space(SCGCQ01586721) 
 - SCGCQ01588880:(SCGCQ01588880) 
 - LSA shows wrong diskgroup info when you have foreign PD(SCGCQ01590450) 
 - IPV6 IP is overlapping OS name and arch in LSA GUI if we see server discovery page in list view in SLES12 SP3(SCGCQ01595641) 
 - WG: LSA service crashes on trying to login with URI having incorrect mac address of the server(SCGCQ01601386) 
 -(SCGCQ01628332) 
 - fixed: Advanced Configuration is grayed out when there are 2 jbods available in the system.(SCGCQ01631267) 
 - Enclosure Location :Internal for back plane needs to be changed to "NONE" as part of new schema-24(SCGCQ01669558) 
 - LSA Schema 24: replace-missing get operation needs to follow the schema(SCGCQ01675460) 
 - Not able to set max no of PD using set patrol read properties in LSA/Storcli(SCGCQ01681070) 
 - WG: LSA 7.7 PA2 Not able to create RAID 00 VDs on iMR Ventura controller(SCGCQ01683638) 
 - When we try to modify the Unmap SCSI Unmap enabled feature via LSA it should give the reboot server message(SCGCQ01683938) 
 - During migration from r0(opal drives and non-secured) to r1, Add Pd list does not list the available drives (Greater/same si(SCGCQ01687072) 
 - WG: Issues pertaining to searching of the server : manual discovery in list view & GUI issues in the manual discovery panel(SCGCQ01687117) 
 - MR7.7_LSA: Unable to convert JBOD to UG when filesystem is present(SCGCQ01697980) 
 - LSA Linux doesn't have latest storelib(SCGCQ01713580) 
 - WG MR 7.7 PA2: LSA allows to add FDE and OPAL drives to create Encrypted volume(SCGCQ01721222) 
 - Server: LSA GUI Not Updating Security Key Info(SCGCQ01761801) 
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events(SCGCQ01761830) 
 - Fixed: nvme is allowed to mix with sas /sata(SCGCQ01762948) 
 - SCGCQ01763132: LSA: Alert Configuration response contains unsupported character(SCGCQ01763132) 
 - Foreign Config preview should show the VD details also(SCGCQ01788639) 
 - LSA Opal: RLM mixing for Opal SSC and Enterprise shouldn't be allowed when enableFDETypeMix=0(SCGCQ01790063) 
 - CC VD creation option is coming in LSA when the CC VD (SATA SSD) is in foreign config.(SCGCQ01817275) 
 - compilation error in server(SCGCQ01817434) 
 - Fixed: Auto Span Adjust with having >64 disks is not correct.(SCGCQ01827404) 
 - Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016(SCGCQ01841473) 
 - LSA Not allowing to clear/Import foreign configuration.(SCGCQ01849749) 
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01856350) 
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01874487) 
 - MR API - Incorrect value used for MR_DCMD_CTRL_SNAPDUMP_ONDEMAND(SCGCQ01882581) 
 - WG: LSA shows incorrect popups while making the drive from offline to online & vice versa(SCGCQ01922610) 
 - LSA - Not able to import other foreign configs if user have SED drive which is in foreign(SCGCQ01937406) 
 - In JBOD personality LSA service getting stopped when user change JBOD to UG(SCGCQ01971368) 
 -(SCGCQ01542415) 
 - LSA 7.6:In gateway LSA, none of the servers are listed except Self server in Remote server discovery page in Rhel 7.4(SCGCQ01552654) 
 - Correcting the library version display, ini file contents and also the readme files contents.(SCGCQ01561849) 
 - LSA: Warning Message needs to be changed when there is Controller firmware update failure(SCGCQ01564526) 
 - SWR: Device ID is not displayed in LSA.(SCGCQ01564621) 
 - MR/IR: Controller Device ID value mismatch in LSA(SCGCQ01564622) 
 - WG:LSA and web server port have references of SLIM and nignx in notification if invalid ports are given during LSA installatn(SCGCQ01571099) 
 - WG: Issues pertaining to replace drive confirmation popup(SCGCQ01573101) 
 - Security related information should not be displayed in IR/IT for LSA(SCGCQ01577891) 
 - LSA allows user to assgin a 512 B drive as replacement to 4k missing drive in a DG(SCGCQ01591175) 
 - SCGCQ01593058: Add non printable character support for sata pd product id display(SCGCQ01593058) 
 - Add a provision to indicate VMware/NonVmware server in Manual Discovery Panel(SCGCQ01600706) 
 - LSA WG FURY IT: UEFI image download is failing in LSA(SCGCQ01616545) 
 - LSA 7.6 Server: LSA is showing the option for PD:"Undo Prepare For Removal", when the DG is in TR state(SCGCQ01618243) 
 - Not able to create secure VD with latest MR 7.7 LSA 177.000.000-SCGCQ01664972 but OK with previous version(SCGCQ01665121) 
 - Error observed while adding Windows gateway server in through manual discovery(SCGCQ01675601) 
 - Secure Jbod unlock is not showing the proper error message in LSA(SCGCQ01677101) 
 - LSA MR7.7 PA2: Previously cleared configuration is seen in presence of OPAL foreign drive in Jbod Mode.(SCGCQ01685488) 
 - WG MR7.7 PA2:Once the 69639 error code is seen in LSA, performing every valid operation fails until manual refresh is perfo(SCGCQ01686013) 
 - WG MR 7.7:There is no import option for GHS Foreign device in LSA(SCGCQ01698105) 
 - Fixed: LSA handle count increase was observed(SCGCQ01713154) 
 - Add physical Drives page is not consistent across (Advanced Configuration and Modify drive Group(SCGCQ01716606) 
 - LSA: Handle Opal drive scenario for Hotspare and replace drive(SCGCQ01719043) 
 - LSA client: Add support to show incompatible profiles details(SCGCQ01727270) 
 - Add SCSI Unmap property at PD level(SCGCQ01732785) 
 - WG MR 7.7 Alpha:Foreign configuration pane does not show details for foreign dedicated hotspare drive.(SCGCQ01745770) 
 - WG:[intermittent] LSA page goes blank if we click on Drive tab and then immediately click on view serer profile(SCGCQ01747490) 
 - WG MR 7.7 alpha:Lsa does not update the PD(part of r0 volume) status once the PD is made online from offline.(SCGCQ01752969) 
 - [CISCO][TR]"Clear Transport Ready" option on rebuild LD should be removed or greyed out in LSA(SCGCQ01753229) 
 - MR LSA 7.7 : When user has flashed the controller FW for IT card, reboot system message is disappearing within few seconds(SCGCQ01761269) 
 - WG MR 7.7 al:LSA allows to create simple configuration in presence of Unconfigured bad drive and rest of the drives in jbod(SCGCQ01763742) 
 - MR7.7: Removal of UNMAP support for JBOD(SCGCQ01813078) 
 - Not able to create PRL11 CC VD (using 4 SATA SSD PD) from LSA webGUI.(SCGCQ01822209) 
 - fixed: LSA fails to create RAID 10 with large number of drives(SCGCQ01833469) 
 - LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online" .(SCGCQ01838943) 
 - WG: Software licensing agreement for linux RWC3 build is of Generic Channel(SCGCQ01886563) 
 - WG: LSA services crashes while adding the manually discovered VMware server to the manage server list(SCGCQ01918692) 
 -(SCGCQ01534450) 
 - LSA needs to change "Error code" : 86017, Description:Operation failed because of a resource reservation error" to proper mes(SCGCQ01556013) 
 - MR7.6_LSA: No Foriegn configuration details is shown in LSA(SCGCQ01581943) 
 - SCGCQ01582139: MR7.6_LSA: Enclosure ID and Device ID is shown blank in LSA event logs(SCGCQ01582139) 
 - WG: LSA Page auto scrolls down with scheduler wrapper going out of focus. LSA page would now be only half transparent(SCGCQ01586697) 
 - PH7 LSA WG Ventura: Sorting the drives on the basis of Device ID is not working fine(SCGCQ01587630) 
 - Fixed: Gateway crash when DA is logged in greater than max logins(SCGCQ01593855) 
 - WG: Instance validation failed for controller GET(SCGCQ01601458) 
 - WG: Minor text changes to be made in user information when no rows are selected in PD tab / DG tab / other hardware tab(SCGCQ01601656) 
 - [CISCO][TR] LSA fails to show DG in TR state after system reboot -storCLI OK(SCGCQ01615856) 
 - Enclosure Location :Internal for back plane needs to be changed to "NONE" as part of new schema-24(SCGCQ01638193) 
 - SCGCQ01680714: WG:Memory leak issues when the system is not idle ( Running the GUI suite when the memory leak test is in progress(SCGCQ01680714) 
 - LSA Wont display foreign data when enclosure information in not populated properly(SCGCQ01685449) 
 - WG MR 7.7:Invalid Temperature is displayed for OPAL drives.(SCGCQ01686024) 
 - Instant Secure Erase does not work in VMware when schedule is enabled(SCGCQ01686028) 
 - MR7.7_LSA: Error code:0 is observed when driver security is changed in LSA(SCGCQ01686050) 
 - LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode(SCGCQ01716622) 
 - fixed: max pd is a bigger number than the actual allowed max pd per raid level(SCGCQ01746200) 
 - WG MR 7.7 alpha: LSA displays wrong connector & path info for drives when enclosure is connected in wide port (x8 connection(SCGCQ01764794) 
 - WG: gateway system is not discovering systems with different web port number in remote discovery page.(SCGCQ01788630) 
 - LSA does not update the VD status when Migration is performed from r5(3drives)to r1(2drives)(SCGCQ01803743) 
 - LSA 502 Bad gateway is seen when Prepare for removal is performed on 5 drives at a time.(SCGCQ01809413) 
 - LSA : Stale entries are coming in DG tab when the VD (failed) is in foreign config.(SCGCQ01818953) 
 - fixed: Info "1920 more drives can be added" need to change in LSA(SCGCQ01827401) 
 - The display wrong location in page(SCGCQ01836732) 
 - SCGCQ01355833: WG:After deleting the cookies from browser, DA does not go back to login page.(SCGCQ01355833) 
 - WG: Changing the drive security key with invalid authentication key results in notification that is not in format(SCGCQ01573090) 
 - WG: Raid 00 DG having missing drives Span list dissapears when user tries to sort the drives based on capacity(SCGCQ01577833) 
 - MR 7.7: LSA did not allow to pick all SED/FDE but OK to pick one by one when create secure VD(SCGCQ01629062) 
 - SCGCQ01718994: LSA needs to convert "Error Code:69637. Descrption:Partial Success.0 Successful;1 Failed" into a readable message.(SCGCQ01718994) 
 - When there is pending personality, do not allow behavior Mode change, GUI refresh issue(SCGCQ01731312) 
 - Assign DHS is not showing any message in failure case(SCGCQ01732485) 
 - To enable the Alarm user has to click on the bottom of checkbox(SCGCQ01740783) 
 - LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap(SCGCQ01818960) 
 - LSA:fw error "BAIL_OUT at line 2909",FDE drive filtering for creating Encrypted RAID0 volumes lists non-FDE drives(SCGCQ01850008) 
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01876091) 
 - LSA needs to convert "Error Code:69637. Descrption:Partial Success.0 Successful;1 Failed" into a readable message.(SCGCQ01533554) 
 - WG: change Behavior Mode From JBOD to None is Not Working until closing the window(SCGCQ01635541) 
 - WG MR7.7PA2:In Jbod mode after first reboot and after converting Jbod to UG, advance configuraton leads to Jbod table.(SCGCQ01683001) 
 - MR 7.7 PA2: LSA does not refresh DG icon when PDs are made offline to online and visa versa.(SCGCQ01686029) 
 - WG MR 7.7 PA2:Encrypted Opal drive VD supports the Opal drive replacement with FDE drive(SCGCQ01697265) 
 - WG: JBOD conversion popup appears multiple times after converting all the drives to UG and clicking on Continue button(SCGCQ01737550) 
 - MR 7.7 alpha: LSA displays raid 1 as raid 1E when created using 4 drives.(SCGCQ01764771) 
 - SCGCQ01564386: IT-FURY-PH16:Drives are not listed under Enclosures ( "0" drives) under other Hardware if connected in Multipath.(SCGCQ01564386) 
 - Coverity Defect fix in 7.7 Stream(SCGCQ01682365) 
 - WG MR 7.7:Invalid Temperature is displayed for OPAL drives.(SCGCQ01714415) 
 - Client changes for defect SCGCQ01629703(SCGCQ01714659) 
 - MR7.7_LSA: After disabling PR, PR properties shows next scheduled time(SCGCQ01718119) 
 - LSA does not give expand option to perform OCE when one among 2vds is deleted under a DG(SCGCQ01803722) 
 - LSA is not locating all drives correctly(SCGCQ01924674) 
 - WG: LSA page doesnt show any notification on time consuming response operations,would lead to user redoing same again(SCGCQ01515496) 
 - WG: Email setting tab heading of LSA displays the entire sentence with "_" in between instead of space(SCGCQ01563343) 
 - Security Key Confirm Text box should not accept the copy of anything(SCGCQ01629574) 
 - Fixed: Show Advanced Config menu only if Unconfigured UG is present(SCGCQ01629703) 
 - WG: Readme shows wrong Version of LSA in html\files\LSA_ReadMe\LSA_Readme(SCGCQ01822525) 
 - SCGCQ01822561: WG: Changed LSA port is not listed after Direct agent installation on Rhel(SCGCQ01822561) 
 - Fixed: unblock LSA login on ESXi 6.7 U1(SCGCQ01866289) 
 - Linux system is getting IPV6 by default & it is not taking private IPV4 range(10 series) in LSA main page.(SCGCQ01817305) 
 - Making rebuild drive offline lsa gets 404.(SCGCQ01564627 port of SCGCQ01542412) 
 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade(SCGCQ01564633 port of SCGCQ01562368) 
 - LSA Crashes after clicking on foreign configuration(SCGCQ01564739 port of SCGCQ01545262) 
 - LSA WG Fury IT: Fury Device ID is showing as 00 instead of 0x0097 in controller properties logs.(SCGCQ01564943 port of SCGCQ01534444) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01565025 port of SCGCQ01504080) 
 - LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4(SCGCQ01565116 port of SCGCQ01555955) 
 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade(SCGCQ01566088 port of SCGCQ01562368) 
 - WG: No success or failure notification is shown on enabling the JBOD drive security(SCGCQ01566435 port of SCGCQ01511274) 
 - SCGCQ01545384: Installation of LSA with LWM option is showing installation_type = 0, in the LSA.conf file(SCGCQ01567110 port of SCGCQ01545384) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01569267 port of SCGCQ01504080) 
 - Making rebuild drive offline lsa gets 404.(SCGCQ01569465 port of SCGCQ01542412) 
 - Schema -23 is not upto date with the Mark/Replace Missing feature(SCGCQ01569474 port of SCGCQ01539349) 
 - LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n(SCGCQ01569949 port of SCGCQ01563340) 
 - LSA WG Inturder IT: 0 Byte drive is missing after sorting the drives based on capacity of drive.(SCGCQ01570203 port of SCGCQ01550970) 
 - Enclosure's physicaldevices URI getting failed with 405 error(SCGCQ01589492 port of SCGCQ01523122) 
 - Label of the user menu drop down should change reinforcing that selection worked.(SCGCQ01597876 port of SCGCQ01493942) 
 - LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n(SCGCQ01599402 port of SCGCQ01563340) 
 - Version changes for LSA 4.129 common project(SCGCQ01601148 port of SCGCQ01601146) 
 - WG:Once the Controller is moved from Raid to JBOD all the drives are counted as drive group(SCGCQ01601603 port of SCGCQ01598515) 
 - LSA: Warning Message needs to be changed when there is Controller firmware update failure(SCGCQ01604992 port of SCGCQ01564526) 
 - MR7.6_LSA: No Foriegn configuration details is shown in LSA(SCGCQ01605344 port of SCGCQ01581943) 
 - fixed: logout causing unexpected behavior during end cim connection for vmware systems(SCGCQ01609343 port of SCGCQ01578248) 
 - SCGCQ01355833: WG:After deleting the cookies from browser, DA does not go back to login page.(SCGCQ01614982 port of SCGCQ01355833) 
 - IPV6 IP is overlapping OS name and arch in LSA GUI if we see server discovery page in list view in SLES12 SP3(SCGCQ01616555 port of SCGCQ01595641) 
 - LSA displays "Erase operation is successful" when replace operation is in progress on the drive in same drive group.(SCGCQ01617930 port of SCGCQ01401460) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01628354 port of SCGCQ01504080) 
 - WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura(SCGCQ01634072 port of SCGCQ01473733) 
 - WG: few of the alert params have the missing controller ID tag for the events(SCGCQ01635756 port of SCGCQ01625923) 
 - LSAServer: Use scheduler call for heavy operations for performance improvement - PD Operations(SCGCQ01635765 port of SCGCQ01514283) 
 - WG: though the hotspare button will be disabled after adding VD for a Raid 1 DG, the hand cursor button appears(SCGCQ01635778 port of SCGCQ01626738) 
 -(SCGCQ01639457 port of SCGCQ01599526) 
 - MR7.6: LSA crashed with a mouse click on VD(SCGCQ01685343 port of SCGCQ01641760) 
 - Raid 1 Volume creation using 4 drives is displayed as Raid 1E(SCGCQ01686231 port of SCGCQ01686106) 
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config(SCGCQ01687172 port of SCGCQ01686080) 
 - When we try to modify the Unmap SCSI Unmap enabled feature via LSA it should give the reboot server message(SCGCQ01697468 port of SCGCQ01683941) 
 - LSA fails to flash GPMR2 package 50.1.0-1048 on top of MR 7.6 package 50.6.0-1255 on first try-it is successful on 2nd try(SCGCQ01697485 port of SCGCQ01680521) 
 - LSA not showing the proper time stamp in the schedule PR page(SCGCQ01698028 port of SCGCQ01677008) 
 - WG: LSA page doesnt show any notification on time consuming response operations,would lead to user redoing same again(SCGCQ01719179 port of SCGCQ01515496) 
 -(SCGCQ01733306 port of SCGCQ01721811) 
 - Fixed: LSA handle count increase was observed(SCGCQ01742153 port of SCGCQ01713154) 
 - Cannot use Special Characters in Domain Name for LSA Login(SCGCQ01747012 port of SCGCQ01745768) 
 - Server schema validation is failing(SCGCQ01764913 port of SCGCQ01619401) 
 - Enclosure Location :Internal for back plane needs to be changed to "NONE" as part of new schema-24(SCGCQ01764928 port of SCGCQ01638193) 
 - LSA installation failed on SLES15(SCGCQ01784699 port of SCGCQ01760620) 
 - LSA needs proper message for max config import(SCGCQ01789100 port of SCGCQ01763411) 
 - Cannot use Special Characters in Domain Name for LSA Login(SCGCQ01789161 port of SCGCQ01745768) 
 - WG: LSA allows user to replace a drive of a DG with drive on which drive clear is already in progress, GUI issues in popup(SCGCQ01810649 port of SCGCQ01803341) 
 - MR7.7: Removal of UNMAP support for JBOD(SCGCQ01813086 port of SCGCQ01813078) 
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config(SCGCQ01816649 port of SCGCQ01686080) 
 - C480-M5: LSA downloaded event log needs better decoding(SCGCQ01828830 port of SCGCQ01321211) 
 - LSA-4.1 : Array details are shown in LSA for the partial foreign config .(SCGCQ01850405 port of SCGCQ01818828) 
 - Tape drive state is blank when connected with 9400-8E card from LSA drives tab(SCGCQ01851980 port of SCGCQ01851906) 
 - LSA Not allowing to clear/Import foreign configuration.(SCGCQ01860933 port of SCGCQ01849749) 
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01880125 port of SCGCQ01874487) 
 - LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap(SCGCQ01897266 port of SCGCQ01818960) 
 - LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online" .(SCGCQ01898344 port of SCGCQ01838943) 
 - fixed: LSA fails to create RAID 10 with large number of drives(SCGCQ01901767 port of SCGCQ01833469) 
 - Fixed: unblock LSA login on ESXi 6.7 U1(SCGCQ01901774 port of SCGCQ01866289) 
 - OPAL drives fail to import when entering wrong security key then right security key after power cycle(SCGCQ01915861 port of SCGCQ01905192) 
 - [CISCO]LSA shows previously set security key (M3g@raid(SCGCQ01921581 port of SCGCQ01878346) 
 - LSA fails to start initialization on EPD if it has DDF(SCGCQ01921583 port of SCGCQ01849522) 
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01921592 port of SCGCQ01829895) 
 -(SCGCQ01921684 port of SCGCQ01841361) 
 - MR7.8 Foreign import from 7.7 to 7.8 with unmap VD and non unmap DHS does not alert user with a critical message/event(SCGCQ01921836 port of SCGCQ01876230) 
 - WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura(SCGCQ01538488 port of SCGCQ01473733) 
 -(SCGCQ01564591 port of SCGCQ01515389) 
 - WG: System display uniformity is not there in GUI (Remote server discovery(SCGCQ01567177 port of SCGCQ01553588) 
 - Client: Handle Enable/Disable style for search Button(SCGCQ01567216 port of SCGCQ01539573) 
 - LSA Crashes after clicking on foreign configuration(SCGCQ01567307 port of SCGCQ01545262) 
 - Manual discovery of servers(SCGCQ01569264 port of SCGCQ01539471) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01569569 port of SCGCQ01504080) 
 - LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n(SCGCQ01570076 port of SCGCQ01563340) 
 - Converting the JBOD Pds to Unconfigured good PD during VD creation VD creation(SCGCQ01597581 port of SCGCQ01518204) 
 - Manual discovery of servers(SCGCQ01600837 port of SCGCQ01539471) 
 - LSA 7.6:In gateway LSA, none of the servers are listed except Self server in Remote server discovery page in Rhel 7.4(SCGCQ01615020 port of SCGCQ01552654) 
 - WG: LSA service crashes on trying to login with URI having incorrect mac address of the server(SCGCQ01615042 port of SCGCQ01601386) 
 -(SCGCQ01633836 port of SCGCQ01599526) 
 - Fixed: Gateway crash when DA is logged in greater than max logins(SCGCQ01635183 port of SCGCQ01593855) 
 - Use schedular call for heavy operations for performance imporvement(SCGCQ01635665 port of SCGCQ01506032) 
 - Allow individual element's properties download - VD / PD / DG / BBU / Server profile(SCGCQ01635761 port of SCGCQ01518113) 
 - JBOD Mode : WG: Even after clicking Convert JBOD the JBOD conversion page does not refresh with updated list(SCGCQ01635784 port of SCGCQ01617721) 
 - Cisco - CSCvi55512 - CC in concurrent mode runs only on 2 VDs at a time(SCGCQ01676612 port of SCGCQ01670094) 
 - Cisco - CSCvi55512 - CC in concurrent mode runs only on 2 VDs at a time(SCGCQ01676732 port of SCGCQ01670094) 
 -(SCGCQ01685548 port of SCGCQ01685009) 
 - LSA Wont display foreign data when enclosure information in not populated properly(SCGCQ01686054 port of SCGCQ01685449) 
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config(SCGCQ01687173 port of SCGCQ01686105) 
 - fixed: WG: managing the manually added server fails : windows(gateway(SCGCQ01697195 port of SCGCQ01682360) 
 - LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode(SCGCQ01716641 port of SCGCQ01716622) 
 -(SCGCQ01718985 port of SCGCQ01698211) 
 - Security Key Confirm Text box should not accept the copy of anything(SCGCQ01788477 port of SCGCQ01629574) 
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01880123 port of SCGCQ01876091) 
 - handling the session management(SCGCQ01892868 port of SCGCQ01829897) 
 - Change tools to report drives attached to HBAs as JBOD instead of UGOOD(SCGCQ01898263 port of SCGCQ01802344) 
 - Fixed: Auto Span Adjust with having >64 disks is not correct.(SCGCQ01901754 port of SCGCQ01827404) 
 - LSA 7.8:LSA provides Instant secure erase option for Locked UG BAD drives.(SCGCQ01904075 port of SCGCQ01893304) 
 - LSA 7.8: Unable to launch LSA from different web server port after LSA upgrade.(SCGCQ01904345 port of SCGCQ01901758) 
 -(SCGCQ01920699 port of SCGCQ01808698) 
 - LSA: Ventura B0: BIOS Flashing Failure Observed in EFI Storcli and Multiple Tries Causes UART Unresponsive(SCGCQ01921839 port of SCGCQ01829669) 
 - SCGCQ01803373: WG: LSA service crashes on downloading support logs in case of Linux 64 bit OS(SCGCQ01921842 port of SCGCQ01803373) 
 - WG: LSA does not notify user on OS VD present if multiple VDs are selected and with non OS VD is selected first(SCGCQ01928961 port of SCGCQ01926674) 
 - LSA Server: Populate the Drive Sector Size while reading the LD MFI command(SCGCQ01930623 port of SCGCQ01926876) 
 - Schema -23 is not upto date with the Mark/Replace Missing feature(SCGCQ01557738 port of SCGCQ01539349) 
 - LSA WG Inturder IT: 0 Byte drive is missing after sorting the drives based on capacity of drive.(SCGCQ01564629 port of SCGCQ01550970) 
 - SCGCQ01547992: WG: standalone LSA Installation on Rhel 6.9 32 bit notifies user with invalid message(SCGCQ01564682 port of SCGCQ01547992) 
 - I/Os are not recover after drives pull for DHSP to rebuild.(SCGCQ01569579 port of SCGCQ01514206) 
 - Support from LSA back-end to allow JBODs to be converted to UG for advance VD creation(SCGCQ01597602 port of SCGCQ01519271) 
 - WG:On changing behavior from None to JBOD and moving to Controller Console page, LSA page redirects to Personality management(SCGCQ01670841 port of SCGCQ01629821) 
 - [CISCO][TR] LSA fails to show DG in TR state after system reboot -storCLI OK(SCGCQ01676281 port of SCGCQ01615856) 
 - Server schema validation is failing(SCGCQ01676389 port of SCGCQ01619401) 
 - WG: Email setting tab heading of LSA displays the entire sentence with "_" in between instead of space(SCGCQ01679003 port of SCGCQ01563343) 
 - Secure Jbod unlock is not showing the proper error message in LSA(SCGCQ01680728 port of SCGCQ01677101) 
 - LSA taking more time to discover VMWare servers(SCGCQ01681092 port of SCGCQ01681069) 
 -(SCGCQ01697478 port of SCGCQ01685009) 
 - LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode(SCGCQ01716625 port of SCGCQ01716622) 
 -(SCGCQ01718980 port of SCGCQ01698211) 
 -(SCGCQ01749087 port of SCGCQ01698211) 
 - Modify Properties option is enabled for VDs which are part of Transport Ready Drive Group(SCGCQ01764894 port of SCGCQ01763056) 
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events(SCGCQ01826237 port of SCGCQ01761830) 
 - The LSA is failing to take into account current USED PDs from another configured VD during next VD creation(SCGCQ01837378 port of SCGCQ01833791) 
 - SCGCQ01841280: Before importing foreign CC VD, model number of SSD is not coming in LSA(SCGCQ01851919 port of SCGCQ01841280) 
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01856730 port of SCGCQ01856350) 
 - WG: VMware server takes too long to discover in remote discovery page : nearly 20 minutes(SCGCQ01891168 port of SCGCQ01889547) 
 - CC VD creation option is coming in LSA when the CC VD (SATA SSD(SCGCQ01897144 port of SCGCQ01817275) 
 - Update the Windows Server 2019 OS name in LSA(SCGCQ01897178 port of SCGCQ01866322) 
 -(SCGCQ01920924 port of SCGCQ01818618) 
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01921819 port of SCGCQ01856350) 
 - LSA 7.6 Client: Cosmetic replace drive selection issue(SCGCQ01566455 port of SCGCQ01539347) 
 - SCGCQ01539326: [UNMAP]MR7.6 Unmap/WriteSame: AEN's are not generated when unmap capability gets disabled or enabled on a VD.(SCGCQ01567176 port of SCGCQ01539326) 
 - WG: Alignment in Remote Server Discovery page changes when it is in List view and filtered with any one of the OS type.(SCGCQ01567193 port of SCGCQ01471834) 
 - SCGCQ01538253: LSA-4.055.0.0: IT-Cutlass- LSA Event logs is missing Enclosure ID's and slot-36 is shown to be present in(SCGCQ01569137 port of SCGCQ01538253) 
 - SCGCQ01538253: LSA-4.055.0.0: IT-Cutlass- LSA Event logs is missing Enclosure ID's and slot-36 is shown to be present in(SCGCQ01569138 port of SCGCQ01538253) 
 - LSA WG Fury IT: Controller type is showing as IR for IT card(SCGCQ01569488 port of SCGCQ01540821) 
 - Client:Allow individual element's properties download - VD / PD / DG / BBU / Server profile(SCGCQ01597592 port of SCGCQ01518206) 
 - WG:Once the Controller is moved from Raid to JBOD all the drives are counted as drive group(SCGCQ01601608 port of SCGCQ01598515) 
 - WG: empty details for policy change displayed in events "Previous = Current Write Policy: Now = Current Write Policy:"(SCGCQ01635759 port of SCGCQ01625912) 
 - WG:On changing behavior from None to JBOD and moving to Controller Console page, LSA page redirects to Personality management(SCGCQ01635779 port of SCGCQ01629821) 
 - TR VD should be excluded from the PR VD list(SCGCQ01677110 port of SCGCQ01677062) 
 - Implemented: Allow mixing of nvme drives to be mixed with SATA/SAS drives(SCGCQ01697042 port of SCGCQ01697026) 
 - Hercules : Snap 4 : Alpha : LSA provides option of performing an RLM operation on Degraded VD, which fails(SCGCQ01789156 port of SCGCQ01731931) 
 - MR7.6: LSA crashed with a mouse click on VD(SCGCQ01816428 port of SCGCQ01641760) 
 - Handling the set text mechanism in client(SCGCQ01886532 port of SCGCQ01850387) 
 - Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016(SCGCQ01897181 port of SCGCQ01841473) 
 - WG: LSA provides option of Secure using FDE if non encrypted r1 VD with secure drive is assigned with DHSP,(SCGCQ01915812 port of SCGCQ01906914) 
 - LSA 7.8:Import option is given for the Incomplete foreign VD(SCGCQ01921678 port of SCGCQ01865420) 
 - LSA is allowing to delete OS VD.(SCGCQ01921689 port of SCGCQ01873420) 
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01921919 port of SCGCQ01856350) 
 - WG: VMware server takes too long to discover in remote discovery page : nearly 20 minutes(SCGCQ01961510 port of SCGCQ01889547) 
 - Not able to set max no of PD using set patrol read properties in LSA/Storcli(SCGCQ01697480 port of SCGCQ01681070) 
 - Add Virtual Drive option is available for DGs with Transport Ready feature set(SCGCQ01764885 port of SCGCQ01763052) 
 - SCGCQ01538253: LSA-4.055.0.0: IT-Cutlass- LSA Event logs is missing Enclosure ID's and slot-36 is shown to be present in(SCGCQ01828400 port of SCGCQ01538253) 
 - Fixed: Crash when pressing back button after logout(SCGCQ01892905 port of SCGCQ01865309) 
 - Remove un printable characters from LSA log(SCGCQ01901769 port of SCGCQ01901760) 
 - LSA does not show Secure Erase option for foreign secured JBOD drive-CLI works(SCGCQ01920701 port of SCGCQ01916249) 
 - WG: LSA allows to remove the data drive during the RLM from single drive R0 and allows migrate to R0 with no drives(SCGCQ01921580 port of SCGCQ01823858) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01565119 port of SCGCQ01504080) 
 - LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4(SCGCQ01569761 port of SCGCQ01555955) 
 - Unable to import foreign secured VDs with different security key(SCGCQ01731357 port of SCGCQ01670139) 
 - Activity to check-in Auto-BST files to 7.8 streams(SCGCQ01794950 port of SCGCQ01793057) 
 - Activity to check-in Auto-BST files to 7.8 streams(SCGCQ01817915 port of SCGCQ01793057) 
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01869566 port of SCGCQ01829895) 
 - Server: LSA GUI Not Updating Security Key Info(SCGCQ01897099 port of SCGCQ01761801) 
 - LSA WG Fury IT: Controller type is showing as IR for IT card(SCGCQ01564631 port of SCGCQ01540821) 
 - LSA Schema 24: replace-missing get operation needs to follow the schema(SCGCQ01679329 port of SCGCQ01675460) 
 - LSA shows wrong diskgroup info when you have foreign PD(SCGCQ01698150 port of SCGCQ01590450) 
 - LSA needs proper message for max config import(SCGCQ01813925 port of SCGCQ01764977) 
 - UG LSA 7.8 PA2:Incomplete foreign VD is seen when Clear foreign config is performed.(SCGCQ01851155 port of SCGCQ01849681) 
 - Fixed: Advance configuration operation should be greyed out if max pds are already configured(SCGCQ01922015 port of SCGCQ01850445) 
 - I/Os are not recover after drives pull for DHSP to rebuild.(SCGCQ01564737 port of SCGCQ01514206) 

EnhancementRequests:
 - Add "Replace Missing Drive" feature to LSA(SCGCQ01399204) 
 - Part 2 of 2: Support TCG Opal 2.0 via SafeStore for VDs and SystemPD (Legacy JBOD) in RAID Mode and JBOD/SDS Modes(SCGCQ01599762) 
 -(SCGCQ01740789) 
 - Added customer serial number field to MFC Manufacturing 2 structure(SCGCQ01873417) 
 - MR API changes to support EKMS over OOB(SCGCQ01874035) 
 - Add new error code for tampered or invalid controller(SCGCQ01885686) 
 - Interrupt coalsecing setting per group of 8 replies queues (h/w VF registers(SCGCQ01886424) 
 - [MR 7.8] API change to export "disable least latency mode"(SCGCQ01887495) 
 - HDET: Support smp passthrough storeliboob (API changes requirement(SCGCQ01916035) 
 - Add secure boot key update complete event(SCGCQ01928254) 
 - Add Board Support Package Image Type to MR_IMAGE_TYPE(SCGCQ01931637) 
 - Support dynamically add/remove controller in Storelib IT for MCTP over PCIe(SCGCQ01934815) 
 - Fix MR_CTRL_INFO to support backward compatibility(SCGCQ01946548) 
 - Add "Replace Missing Drive" feature to LSA(SCGCQ01399205) 
 - Manually add server details to the list of servers(SCGCQ01539514) 
 - Switch attached NVMe HW RAID support for Supermicro backplanes(SCGCQ01740787) 
 - LSA displays "Erase operation is successful" when replace operation is in progress on the drive in same drive group.(SCGCQ01401460) 
 - UNMAP/TRIM/WRITESAME for NVMe devices for R0/EPD/JBOD(SCGCQ01746609) 
 - Manual discovery of servers(SCGCQ01539471) 
 - Change tools to report drives attached to HBAs as JBOD instead of UGOOD(SCGCQ01802344) 
 -(SCGCQ01599763) 
 - UNMAP/TRIM/WRITESAME for NVMe devices for R0/EPD/JBOD(SCGCQ01746608) 


004.069.000.000  - Moderate Impact
---------------

Defects (20)
-.(SCGCQ01753405)
- Server: LSA GUI Not Updating Security Key Info.(SCGCQ01761801)
- CC VD creation option is coming in LSA when the CC VD (SATA SSD) is in foreign config.(SCGCQ01817275)
- Fixed: Auto Span Adjust with having >64 disks is not correct.(SCGCQ01827404)
- Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016.(SCGCQ01841473)
- LSA Not allowing to clear/Import foreign configuration.(SCGCQ01849749)
- SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon.(SCGCQ01856350)
- LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01874487)
- seg fault is seen when when we try to generate CRC errors using megamon.(SCGCQ01841619)
- Not able to create PRL11 CC VD (using 4 SATA SSD PD) from LSA webGUI.(SCGCQ01822209)
- fixed: LSA fails to create RAID 10 with large number of drives.(SCGCQ01833469)
- LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online".(SCGCQ01838943)
- LSA : Stale entries are coming in DG tab when the VD (failed) is in foreign config.(SCGCQ01818953)
- fixed: Info "1920 more drives can be added" need to change in LSA.(SCGCQ01827401)
- The display wrong location in page(SCGCQ01836732)
- LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap.(SCGCQ01818960)
- LSA:fw error "BAIL_OUT at line 2909",FDE drive filtering for creating Encrypted RAID0 volumes lists non-FDE drives.(SCGCQ01850008)
- LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01876091)
- Fixed: unblock LSA login on ESXi 6.7 U1.(SCGCQ01866289)
- Linux system is getting IPV6 by default & it is not taking private IPV4 range(10 series) in LSA main page.(SCGCQ01817305)
- Security Key Confirm Text box should not accept the copy of anything.(SCGCQ01788477 port of SCGCQ01629574)
- SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon.(SCGCQ01856730 port of SCGCQ01856350)
- The LSA is failing to take into account current USED PDs from another configured VD during next VD creation.(SCGCQ01837378 port of SCGCQ01833791)
- SCGCQ01538253: LSA-4.055.0.0: IT-Cutlass- LSA Event logs is missing Enclosure ID's and slot-36 is shown to be present in.(SCGCQ01828400 port of SCGCQ01538253)
- Activity to check-in Auto-BST files to 7.8 streams.(SCGCQ01817915 port of SCGCQ01793057)
- SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01869566 port of SCGCQ01829895)

EnhancementRequests (20)
- RTTrace API Changes.(SCGCQ01745568)
- API Changes for Driver/FW DCMD HandShake.(SCGCQ01841266)
- RTTrace Enable/Disable API changes.(SCGCQ01830211)
- Criteo: API changes reversal.(SCGCQ01760512)
- Mixing Rules for SED and non-SED drives to create non-secure array with controller security enabled.(SCGCQ01757538)
- Unmap: Define new API for enhanced UNMAP support.(SCGCQ01758062)
- Adding API bit to indicate whether forced personality change is supported or not.(SCGCQ01762153)
- Unmap: Define new events for enhanced UNMAP support [MR7.8].(SCGCQ01803319)
- Deprecate the snap dump fields that are no longer needed for MR_SNAP_DUMP_PROPERTIES structure.(SCGCQ01816724)
-.(SCGCQ01818580)
- Add the API to clear all the snap-dumps from firmware.(SCGCQ01824135)
- API change to provide learn complete timestamp.(SCGCQ01845269)
- Added Support for Triggering SnapDump.(SCGCQ01848759)
- Add secure boot support.(SCGCQ01792416)
- Including The Time Stamp for every Snap Dump created in the firmware.(SCGCQ01797424)
- Aero FW - Reporting SSD wear gauge values for OEM specific customers.(SCGCQ01798686)
- [MR 7.8] API change to return apt failure status for a personality change request.(SCGCQ01853480)
- Added new events for unmap policy changes.(SCGCQ01871912)
- API Changes - After Vision PSOC FW update, applications should ask the user for power cycle instead of reboot.(SCGCQ01765150)
- Change tools to report drives attached to HBAs as JBOD instead of UGOOD.(SCGCQ01802344)


004.062.000.000  - Moderate Impact
--------------
fixed:
Nginx versions since 0.5.6 up to and including 1.13.2 are vulnerable to integer overflow vulnerability in nginx range filter module resulting into leak of potentially sensitive information triggered by specially crafted request.https://nvd.nist.gov/nvd.cfm?cvename=CVE-2017-7529.

Defects (109)
- LSA server report for iMR Inv controller displays dedicatedHotSparePerDriveGroup is 0 under "maxLimit".(SCGCQ01375788)
- SCGCQ01393056: Enclosure ID is coming up as null in LSA.(SCGCQ01393056)
- WG: Error message not fitting inside the message box in "Enable Drive Security" page..(SCGCQ01442477)
- WG: Issues pertaining to 'Make JBOD Secure' Pop up.(SCGCQ01446801)
- PerfImp: Don't handle SLIM_EVT_EXCEEDS_MAX if there is no event requires complete refresh.(SCGCQ01447165)
- WG: UI Pattern in "Virtual Drive Settings" is not uniform while creating and modifying VD properties..(SCGCQ01447697)
- WG: "Change" button shown as disabled when user tries to change Behavior mode..(SCGCQ01450713)
- DG count is shown incorrectly in server summary page : VMware 6.5.(SCGCQ01451571)
- WG: success message box for "change personality" does not have proper border.(SCGCQ01453980)
- WG: Event Log table headers needs space - Cosmetic.(SCGCQ01460053)
- WG: Notification after saving the changes in "Manage Power Save Settings" needs cosmetic change..(SCGCQ01460078)
- Requested personality field is not updated for Ventura.(SCGCQ01465642)
- API performance Issues pertaining to LSA Build 004.005.000.000( VMware esxi 6.5 ): Raid Mode with JBOD drives.(SCGCQ01467754)
- WG: Tooltip for help link in "Remote Server Discovery" page is not displayed..(SCGCQ01471842)
- WG: "Available UG drives" form is shown blank when "Type" is selected from ALL to any other drives..(SCGCQ01472186)
- WG: LSA showing inappropriate message after securing a DG using FDE security..(SCGCQ01472201)
- Buttons are inconsistent in Email Settings page of LSA.(SCGCQ01472752)
- Fixed: LSA app UI cannot be opened when connect M.2 NVME SSD(via HSBP) to LSI 9460-16i/9440-8i.().(SCGCQ01474461)
- MR 7.3.1_LSA fails to find server when there is no network.(SCGCQ01482320)
- During Advanced Vd Creation PD selection order is not maintained by the client.(SCGCQ01498969)
- Display the ROC temperature in Fahrenheit as well along with Celsius.(SCGCQ01504619)
- WG: Hand mouse pointer is used in " Background Process progress " window , where it shows the name of background operations..(SCGCQ01505999)
- [lenovo 18A] [Bugzila 117507] -Reopen -The LSA doesn’t work in Suse12.3, which has many NICs.(SCGCQ01506045)
- WG: Caps letter is expected in Settings for Alert settings successful and restore default value successful message..(SCGCQ01509253)
- WG: Sorting of drives by model number does not work for JBOD drives.(SCGCQ01511247)
- Do not allow the user to manage Personality Panel if set personalty is not supported.(SCGCQ01514527)
- SCGCQ01515443: WG: Typo in Event ID: 114 of PD state Change event related to sheild state.(SCGCQ01515443)
- 502 bad gate way observed on enclosure cable push/pull.(SCGCQ01524150)
- WG : LSA allows to add VD on offline DriveGroup and operation fails anyways.(SCGCQ01526342)
- MR 7.5_LSA: LSA gives wrong message after Online FW Update on Ventura IMR controller.(SCGCQ01532725)
- LSA shows wrong diskgroup info when you have foreign PD.(SCGCQ01590450)
- Lenovo_18B: Not able to set max no of PD using set patrol read properties in LSA/Storcli.(SCGCQ01681070)
- Fixed: LSA handle count increase was observed.(SCGCQ01713154)
- Lenovo CIT 18B: LSA Linux doesn't have latest storelib.(SCGCQ01713580)
- SCGCQ01385340: Health is not coming proper after foreign config import..(SCGCQ01385340)
- Disabled Phy is not populated from the server when we fire /phys uri.(SCGCQ01389892)
- MR7.3_Focused Regression_Strange character when exceeding max number of Uncof good drives on iMR.(SCGCQ01419325)
- WG: Not all space in "Foreign Configuration" tab is clickable..(SCGCQ01467702)
- WG: Font style across the "Advanced Configuration" form should be made same..(SCGCQ01472063)
- Removing dead code from LSA7.5 stream..(SCGCQ01472185)
- WG: "Ok" button needs to be in caps in "Mixed listed drives" confirmation page and one more cosmetic change..(SCGCQ01472190)
- WG: There is no alignment for the error message while user changes the personality mode when PR is in progress..(SCGCQ01474932)
- WG: LSA is not allowing User to change No of PD's allowed for Patrol Read in Set PR properties through KeyBoard..(SCGCQ01479402)
- WG: Trying to clear configuration does not show any warning in server summary page regarding cached data, in CC page it shows.(SCGCQ01486698)
- WG: Select all check box is still selected even if one of the drive group is unselected while assigning HSP to existing DG.(SCGCQ01488141)
- WG: while creating FDE VD, type by default is selected as "All" in PD selection pane, unable to select all FDE drives.(SCGCQ01488169)
- Requested personality field is not updated for Ventura.(SCGCQ01494598)
- temperature change in controller is not refeclected in LSA..(SCGCQ01500344)
- Set patrol read window shows a time in past..(SCGCQ01503810)
-.(SCGCQ01508528)
- SCGCQ01509259: WG: Separator is missing in few places of event logs..(SCGCQ01509259)
- WG: LSA provides option of performing an RLM operation on Degraded VD, which fails.(SCGCQ01509708)
- LSA Server: Set Patrol read is not shown when the volume is created with SSD.(SCGCQ01511260)
- SCGCQ01513209: WG: Simple configuration tab show invalid options before the raid level drop down list the supported raid levels.(SCGCQ01513209)
- WG : Advanced configuration tab gets disabled after secure erasing the FDE foreign drives.(SCGCQ01514728)
- SCGCQ01521013: MR 7.5_LSA: LSA gives wrong message after Online FW Update on Ventura IMR controller.(SCGCQ01521013)
- MR 7.5_LSA: LSA keeps on refreshing during the background operations- Full init, RLM, CC etc.(SCGCQ01522807)
- WG: Behavior mode is missing in "personality management" window..(SCGCQ01523045)
- SCGCQ01525738: MR 7.5_LSA: Wrong nginx version is reported in linux ( SLES and RHEL ) Operating Systems..(SCGCQ01525738)
- Instance validation issues with LSA build 4.55 with IR3 controller.(SCGCQ01528425)
-.(SCGCQ01628332)
- WG: Current Profile is not selected by default in the table that lists the available profiles for the controller..(SCGCQ01442481)
- WG: "%" is accepted along with the input for Expand VD value - But not accepted for all..(SCGCQ01445384)
- WG: Partition line is required in Controller Properties Page..(SCGCQ01445396)
- WG: Status icon of physical drive is not changed after changing the state of the PD from rebuild to offline..(SCGCQ01461144)
- WG:LSA doesn't allow to secure more than one DG using FDE..(SCGCQ01472853)
- SCGCQ01474327: Handle dynamic length serial number as part of serial number VPD page 0x80.(SCGCQ01474327)
- WG: GUI : Cosmetic issues in clear configuration notificationp.(SCGCQ01486692)
- WG: LSA does not notify the user with notification on starting the VD initialization.(SCGCQ01487270)
- WG: able to add VD for scheduling consistency check even after all the VD's have been deselected.(SCGCQ01489509)
- WG:Add physical Drive button is clickable before VD list is loaded while scheduling CC or PR, no notification to user to wait.(SCGCQ01489885)
- LSA provides option of performing an RLM operation on Degraded VD, which fails.(SCGCQ01489942)
- LSA: Virtual drive, spare and drivegroup is not supported for IT but seen in URI response for Physical drives..(SCGCQ01500099)
- WG: Selection of different drive type is activated after few clicks.(SCGCQ01503786)
- RWC3 launch tab is showing the LSI Storage Authority.(SCGCQ01503896)
- WG : Pop up for securing FDE drive has inconsistency in text.(SCGCQ01507972)
- In settings window "Restore Default Alert settings" button is not saving the default values.(SCGCQ01508002)
- WG: Confirm Check box is not aligned with the "Enable Security" button.(SCGCQ01511250)
- LSA WG: arrow mark in the link " <- Go back to Drive Group, Drives and Other Hardware list" is not clickable.(SCGCQ01511390)
- WG:Server Logs does not contain status of energy pack it mentions "Requested element not found in the stack.":error "69634".(SCGCQ01512318)
- WG: Spell Check issues with "message_en.js" used for displaying the GUI notification.(SCGCQ01512377)
- Sorting of Event logs wrt View Events and Download Logs.(SCGCQ01512750)
- WG: LSA add physical Disks pane shows empty drive list even if there are 182 drives for adding for RLM operation.(SCGCQ01513656)
- Controller operations schema instant validation is failed.(SCGCQ01514528)
- WG: LSA shows the message "The virtual disk has not been initialized" even when 32 VD's have been selecte.(SCGCQ01521694)
- Lenovo-18B: IPV6 IP is overlapping OS name and arch in LSA GUI if we see server discovery page in list view in SLES12 SP3.(SCGCQ01595641)
- WG: "Virtual Drive expanded successfully" message is still shown even after the page refresh post VD expansion..(SCGCQ01445693)
- WG: Cosmetic changes required in tooltip messages of Configure options in Controller Actions..(SCGCQ01447797)
- WG: Space is required between RAID and it's type in Available UG drives form and one more cosmetic change..(SCGCQ01472194)
- WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura.(SCGCQ01473733)
- LSA: partial VD hide operation is failing..(SCGCQ01484118)
- SCGCQ01506090: WG: In Settings under email tab , email id list will always have an empty row once we add and remove email_id.(SCGCQ01506090)
- WG:Launching LSA using ip:2463 in browser, User can see the HOME page flash before redirecting to Remote discovery.(SCGCQ01439795)
- WG: LSA displays empty box instead of "Action Successful" for "Prepare for removal" and "Undo prepare for removal".(SCGCQ01447823)
- WG: "Adding the virtual drive will add the corresponding virtual drives for PR" is not shown when "select all" box is used..(SCGCQ01461133)
- WG: Size of "Back" & "Save" buttons are not same once the user saves the changes after scheduling CC.(SCGCQ01472749)
- WG: Hand symbol is not seen for close button while Adding drive during reconstruction of a DG.(SCGCQ01473748)
- Disabling the add PD button.(SCGCQ01488036)
- WG: no notification shown on assigning dedicated hotspare to existing DG.(SCGCQ01488155)
- System x PE: LSA Does Not Support the Hyphen Character "-" In Domain Names.(SCGCQ01507989)
- WG: Infinite request observed on stopping LSA and Nginx services..(SCGCQ01509681)
- WG: Error message on a failed operation of RLM in displayed outside the allocated space.(SCGCQ01515263)
- WG: arrow mark in the link " <- Go back to Drive Group, Drives and Other Hardware list" is not clickable.(SCGCQ01442471)
- WG: Expand windows is showing the capacity in decimal value with too many integers after decimal point..(SCGCQ01445686)
- Address Code review defects for ER SCGCQ01416373.(SCGCQ01455923)
- WG: Ambiguous "Success" message needs to be changed for disabling drive security.(SCGCQ01461177)
- Cannot import foreign configuration from LSA.(SCGCQ01524354)
- WG: Email setting tab heading of LSA displays the entire sentence with "_" in between instead of space.(SCGCQ01563343)
- SCGCQ01599526: Lenovo PE: Memory Leak in LSABug.(SCGCQ01599526)

EnhancementRequests (20)
- New configuration params added for EPD-PT devices.(SCGCQ01599607)
- API changes needed to support eHBA product series.(SCGCQ01727346)
- Create sanitize events.(SCGCQ01713708)
- Modify event string APIs for MISSING and OFFLINE LDs.(SCGCQ01628177)
-.(SCGCQ01404233)
- SCSI UNMAP switching support from LSA GUI.(SCGCQ01461207)
- NVDATA parameter to OPAL SED.(SCGCQ01614689)
- Add new MFI Status to block requested operation due to existing controller configuration.(SCGCQ01670135)
- Change the mr.h API comment showing the new return status for the - MR_DCMD_PD_GET_INFO.(SCGCQ01670234)
- API change for Switch attached NVMe HW RAID support for Supermicro backplanes.(SCGCQ01697667)
- LSA: Make heavy operation by wrapping scheduler call.(SCGCQ01416373)
 - LSA Server: PR:SCGCQ01231749 -- Show controller temperature in LSA for RAID and SAS IT controllers.(SCGCQ01443721)
- LSA Server: PR:SCGCQ01231749 -- Show controller temperature in LSA for RAID and SAS IT controllers.(SCGCQ01443731)
- Support drive Select ALL functionality in LSA GUI PD Operations and Mixing of drives during vd creation.(SCGCQ01454110)
- SCGCQ01454353: Retrieve and process the ESXi events in a single shot.(SCGCQ01454353)
-.(SCGCQ01454367)
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01563340)
- We will be removing the confirmation popup from all the actions as we got here from multiple forms like this pop up is annoying.(SCGCQ01447015)
- Support drive Select ALL functionality in LSA GUI VD/DG Operations.(SCGCQ01453114)
-.(SCGCQ01472631)

CSETActivities (87)
- In Standalone LSA periodic automatic refresh is not happening. To display the latest status do manual refresh.(SCGCQ01411631 port of SCGCQ01397546)
- MR7.3_Focused Regression_Strange character when exceeding max number of Uncof good drives on iMR.(SCGCQ01420224 port of SCGCQ01419325)
- LSA service is not working in Linux.(SCGCQ01443712 port of SCGCQ01442733)
- WG: Event Log table headers needs space - Cosmetic..(SCGCQ01464556 port of SCGCQ01460053)
- SCGCQ01424621: PD serial number getting truncated on few PDs.(SCGCQ01466763 port of SCGCQ01424621)
- MR 7.3.1_LSA fails to find server when there is no network.(SCGCQ01500133 port of SCGCQ01482320)
- Updated PD firmware version is not reflecting even after LSA refresh..(SCGCQ01501204 port of SCGCQ01382013)
- Cisco_Plumus_LR :Proper spacing should be there in between Event and History in view event logs "EventHistory not generated"..(SCGCQ01502201 port of SCGCQ01385344)
- While retrieving the enclosure details instead of referring to the ENCL structure, in this case LSA is referring the PD structure.(SCGCQ01503907 port of SCGCQ01315392)
because of which the issue.(SCGCQ01503926 port of SCGCQ01288032)
- fixed: clear drive should not be candidate drive for create configuration.(SCGCQ01503958 port of SCGCQ01196088)
- Fixed: Span order is in reverse compare to other apps.(SCGCQ01504234 port of SCGCQ01330269)
- LSA shows max pd for Raid 1 without checking support of Raid 1E.(SCGCQ01514472 port of SCGCQ01513338)
- Cisco - CSCvg96681 - LSA-3.163 should display proper message after logout.(SCGCQ01531154 port of SCGCQ01521114)
- Making rebuild drive offline lsa gets 404..(SCGCQ01564627 port of SCGCQ01542412)
- LSA Crashes after clicking on foreign configuration.(SCGCQ01564739 port of SCGCQ01545262)
- Modify the LSA Health Algorithm to consider the Blocked VD.(SCGCQ01565025 port of SCGCQ01504080)
- LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4.(SCGCQ01565116 port of SCGCQ01555955)
- Cisco - CSCvh55470 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade.(SCGCQ01566052 port of SCGCQ01562368)
- SWR: Device ID is not displayed in LSA..(SCGCQ01566241 port of SCGCQ01564621 )
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01599402 port of SCGCQ01563340)
- MR7.6_LSA: No Foriegn configuration details is shown in LSA.(SCGCQ01605344 port of SCGCQ01581943)
- fixed: logout causing unexpected behavior during end cim connection for vmware systems.(SCGCQ01609343 port of SCGCQ01578248)
- SCGCQ01355833: WG:After deleting the cookies from browser, DA does not go back to login page..(SCGCQ01614982 port of SCGCQ01355833)
- LSA displays "Erase operation is successful" when replace operation is in progress on the drive in same drive group..(SCGCQ01617930 port of SCGCQ01401460)
- SCGCQ01506090: WG: In Settings under email tab , email id list will always have an empty row once we add and remove email_id.(SCGCQ01620406 port of SCGCQ01506090)
- WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura.(SCGCQ01634072 port of SCGCQ01473733)
- Raid 1 Volume creation using 4 drives is displayed as Raid 1E.(SCGCQ01686231 port of SCGCQ01686106)
- Cannot use Special Characters in Domain Name for LSA Login.(SCGCQ01747012 port of SCGCQ01745768)
- LSA: patrol reads gets initiated on all the vd's that are created though only one vd is selected..(SCGCQ01448948 port of SCGCQ01442107)
- DG count is shown incorrectly in server summary page : VMware 6.5.(SCGCQ01460039 port of SCGCQ01451571)
- WG: LSA takes some time (2-3 min) in order to display the remote server page after multiple service restarts..(SCGCQ01465657 port of SCGCQ00903348)
- DG count is shown incorrectly in server summary page : VMware 6.5.(SCGCQ01466743 port of SCGCQ01451571)
- LSA server giving null for enclosure serial number.(SCGCQ01466744 port of )
- Address Code review defects for ER SCGCQ01416373.( port of SCGCQ01445713)
- MR 7.3.1_LSA fails to find server when there is no network.(SCGCQ01484107 port of SCGCQ01482320)
- Added fwflash status as part of controller health status.(SCGCQ01503830 port of SCGCQ01375153)
- While retrieving the enclosure details instead of referring to the ENCL structure, in this case LSA is referring the PD structure because of which the issue.(SCGCQ01503955 port of SCGCQ01288032)
- [lenovo 18A] [Bugzila 117507] -Reopen -The LSA doesn’t work in Suse12.3, which has many NICs.(SCGCQ01514258 port of SCGCQ01506045)
- System x PE: LSA Does Not Support the Hyphen Character "-" In Domain Names.(SCGCQ01514469 port of SCGCQ01507989)
- Allows raid 1e input even if RAID 1E is not supported by fw.(SCGCQ01514756 port of SCGCQ01513331)
- Activity to check-in build files.(SCGCQ01514879 port of SCGCQ01514834)
-.(SCGCQ01520055 port of SCGCQ01508528)
- Cisco - CSCvh55470 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade.(SCGCQ01564633 port of SCGCQ01562368)
- Activity to check-in AutoBST files to new MR 7.5 streams.(SCGCQ01564703 port of SCGCQ01564674)
- WG: LSA service crashes on trying to login with URI having incorrect mac address of the server.(SCGCQ01615042 port of SCGCQ01601386)
- MR7.6: LSA crashed with a mouse click on VD.(SCGCQ01685343 port of SCGCQ01641760)
-.(SCGCQ01685548 port of SCGCQ01685009)
- LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config.(SCGCQ01687173 port of SCGCQ01686105)
- LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode.(SCGCQ01716641 port of SCGCQ01716622)
- SDS/HBA progress issues.(SCGCQ01460070 port of SCGCQ01052983)
- Physical drives Get call taking considerably long time :it takes 5+ minutes to respond for 24 PD's in an enclosure.(SCGCQ01460084 port of SCGCQ01435908)
- SCSI UNMAP switching support from LSA GUI.(SCGCQ01461211 port of SCGCQ01461207)
- C480-M5: LSA downloaded event log needs better decoding.(SCGCQ01501225 port of SCGCQ01321211)
- Cisco - CSCve68492 - Storage Logs display a blank event when a secure PD is unlocked.(SCGCQ01503902 port of SCGCQ01359128)
- SCGCQ01509259: WG: Separator is missing in few places of event logs..(SCGCQ01514773 port of SCGCQ01509259)
- WG: Infinite request observed on stopping LSA and Nginx services..(SCGCQ01526363 port of SCGCQ01509681)
- SCGCQ01547992: WG: standalone LSA Installation on Rhel 6.9 32 bit notifies user with invalid message.(SCGCQ01564682 port of SCGCQ01547992)
- LSA: Warning Message needs to be changed when there is Controller firmware update failure.(SCGCQ01604992 port of SCGCQ01564526)
- SCGCQ01599526: Lenovo PE: Memory Leak in LSA.(SCGCQ01633836 port of SCGCQ01599526)
- Secure Jbod unlock is not showing the proper error message in LSA.(SCGCQ01680728 port of SCGCQ01677101)
- LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config.(SCGCQ01687172 port of SCGCQ01686080)
- Cisco - CSCvi84075 - LSA, CTRL-R and HII doesn't display the foreign config when MAX VDs are present.(SCGCQ01718980 port of SCGCQ01698211)
- LSA is not Displaying Both the Foreign Configurations (Encrypted and Unencrypted) for Import/Clear/re scan..(SCGCQ01460090 port of SCGCQ01460076)
- WG: LSA is not Displaying Both the Foreign Configurations (Encrypted and Unencrypted) for Import/Clear/re scan..(SCGCQ01460400 port of SCGCQ01448976)
- Fixed: LSA app UI cannot be opened when connect M.2 NVME SSD(via HSBP) to LSI 9460-16i/9440-8i.(SCGCQ01481410 port of SCGCQ01474461)
- LSA build script automation for VBAS environment.(SCGCQ01497385 port of SCGCQ01385344)
- Activity to check-in version files in common.(SCGCQ01520315 port of SCGCQ01512599)
- Cisco - CSCvg96681 - LSA-3.163 should display proper message after logout.(SCGCQ01531153 port of SCGCQ01521114)
- MR/IR: Controller Device ID value mismatch in LSA.(SCGCQ01566055 port of SCGCQ01564622)
- LSA Client 7.6: SPAN drives order is not maintained.(SCGCQ01614833 port of SCGCQ01539355)
- Hercules- LSA : VD access policy not showing as blocked for SVD on CC VD offline..(SCGCQ01443689 port of SCGCQ01442554)
- LSA: During the installation "Range of Events" selection is not reflecting in the LSA.conf file.(SCGCQ01472166 port of SCGCQ01472048)
- SCGCQ01479375: LSA WebGui: "logs.txt" is generated in logs directory after fresh installation in Linux..(SCGCQ01480902 port of SCGCQ01479375)
- LSA WG Fury IT: Fury Device ID is showing as 00 instead of 0x0097 in controller properties logs..(SCGCQ01564943 port of SCGCQ01534444)
- Modify the LSA Health Algorithm to consider the Blocked VD.(SCGCQ01565119 port of SCGCQ01504080)
- Cisco - CSCvi55512 - CC in concurrent mode runs only on 2 VDs at a time.(SCGCQ01676612 port of SCGCQ01670094)
- LSA Wont display foreign data when enclosure information in not populated properly.(SCGCQ01686054 port of SCGCQ01685449)
- LSA : Silent installation is accepting the invalid options also for LSA/HPE/RWC3.(SCGCQ01472265 port of SCGCQ01389392)
-.(SCGCQ01564591 port of SCGCQ01515389)
- API performance Issues pertaining to LSA Build 004.002.000.000( VMware esxi 6.5 ).(SCGCQ01460393 port of SCGCQ01436886)
- LSA Windows BST Automation scripts.(SCGCQ01472059 port of SCGCQ01460401)
- LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4.(SCGCQ01557665 port of SCGCQ01555955)
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01564577 port of SCGCQ01563340)
- LSA WG Inturder IT: 0 Byte drive is missing after sorting the drives based on capacity of drive..(SCGCQ01564629 port of SCGCQ01550970)
- LSA WG Fury IT: Controller type is showing as IR for IT card.(SCGCQ01564631 port of SCGCQ01540821)
- I/Os are not recover after drives pull for DHSP to rebuild..(SCGCQ01564737 port of SCGCQ01514206)

4.011.000.000 - Moderate Impact
-------------
Defects (234)
- SDS/HBA progress issues.(SCGCQ01052983)
- Fixed: Added relevant null pointer checks.(SCGCQ01319978)
- Selected firmware version is coming empty for IR/IT/IMR controller.(SCGCQ01321474)
- Start PatrolRead success dialog box needs change in alignment.(SCGCQ01324866)
- WG: Trying to import Encrypted VD with Drive security disabled results in error code: 0x11005, it provides No Details to user.(SCGCQ01325783)
- Link speed is not displaying any details in LSA.(SCGCQ01326129)
- Defect to check in code review defects.(SCGCQ01329391)
- Client js file changes for 7.3.(SCGCQ01331593)
- On Successful Firmware flash client displays improper Icon Message.(SCGCQ01332708)
- Control panel of LSA Help & support link still has reference to LSI. should be changed to broacom.(SCGCQ01337321)
- LSA asks for user permission to navigate away on clicking home button after creating simple configuration.(SCGCQ01338009)
- WG: GUI Issues pertaining to FW flash ER implementation SCGCQ01273627: Request to improve message displayed during FW Update.(SCGCQ01342542)
- IR Card global hot spare assignment is not refreshing the page.(SCGCQ01345357)
- Cisco_HSW_Validation_LSA: LSA accepting decimal values for "Set Adjustable Task Rate" which is saved as round value.(SCGCQ01345553)
- LSA 7.3 Client Coverity fix.(SCGCQ01347309)
- Cisco_LSA: 'vdname' parameter is missing in the event description that is generated whenever a volume property is modified.(SCGCQ01350435)
- WG:descripancies in update firmware page after selecting load bios option.(SCGCQ01350865)
- SCGCQ01350908: WG:Temperature of Unconfigured Drive is displayed as 0C under More properties.(SCGCQ01350908)
- WG:LSA displays Redhat icon in remote discovery page ,though SUSE is installed in system.(SCGCQ01351455)
- LSA taking the max VD size value when the user presses ENTER after specifying the VD size.(SCGCQ01356216)
- SCGCQ01356217: WG: LSA Service crashes on trying the PD details of the simple config created.(SCGCQ01356217)
- LSA_MR_7.3_Alpha: Save option can be grayed out or disabled after user saves the changes for schedule CC.(SCGCQ01357152)
- LSA_MR_7.3_Alpha: LSA doesn't display consistent Foreign Configuration information to the user.(SCGCQ01358048)
- WG: Incorrect notification shown after selecting 32 virtual drives.(SCGCQ01358095)
- SCGCQ01358097: LSA_MR_7.3_Alpha: Space optimization between the size value & size unit is needed in foreign configuration page.(SCGCQ01358097)
- LSA_MR_7.3_Alpha: User cannot select "Advanced Configuration" by clicking on the description below it in Server landing page.(SCGCQ01358122)
- LSA_MR_7.3_Alpha: Space Alignment for better presentation needed in Server Profile Page.(SCGCQ01358148)
- LSA_MR_7.3_Alpha: Percentage value for the Background Operations is not seen if browser is zoomed.(SCGCQ01358261)
- LSA crash when service starts with empty LSA.conf file.(SCGCQ01358264)
- SCGCQ01358892: Buttons "Try Updating Again" is not highlighted when user attempts to flash the firmware after any failure.(SCGCQ01358892)
- SCGCQ01358947: WG: Invalid text Content displayed on selecting multiple Virtual drives/Physical Drives.(SCGCQ01358947)
- WG: "Select Personality" dropdown lists the current personality first by default.(SCGCQ01359030)
- WG: Clickable "hand icon' is not displayed when we move cursor over Bus dev text of controller in Server summary page.(SCGCQ01359034)
- SCGCQ01372670: When User tries to click on Update FW Button, LSA asks for Navigation Confirmation without displaying Update FW page for IT.(SCGCQ01372670)
- "Add CacheCade-SSD VD" tab getting greyed out after deleting created vd,even if physical drive is selected under "Add SSD pd".(SCGCQ01372722)
- WG: VD creation fails when multiple VD's are created with 1MB size.(SCGCQ01373500)
- "Finish" button in Modify drive group work even if its grayed out.(SCGCQ01374945)
- WG: Issues pertaining to Controller Diagnostic logs.(SCGCQ01375839)
- WG: GUI Issues pertaining to Instant secure erase of an FDE Drive.(SCGCQ01375858)
- There is a mismatch about Backplane (Enclosure) "Product ID" and "Enclosure Model" in LSA.(SCGCQ01376005)
- Spare URI does not respond on iMR Invader.(SCGCQ01376605)
- WG: After physically removing the PD from the R10 DG, the DG Span tab does not load.(SCGCQ01376781)
- "Since Log Clear" does not create the last event "Log Clear" in Var/log/messages.(SCGCQ01376849)
- WG: LSA does not list the Drive Group Tab , on creation of 240 VD (15 DG, 16 VD in each of DG) and reinstalling the LSA.(SCGCQ01378585)
- WG: Windows Application Event viewer lists 31 events instead of 30, after installing LSA with the option "Since Last reboot".(SCGCQ01378669)
- WG: LSA does not automatically refresh on hiding an Degraded DG.(SCGCQ01378693)
- Client: Error message that user encounters for Max User login, message needs to be displayed with proper message.(SCGCQ01378778)
- Client: WG: Instance Validation failed for Spares GET URI : MR Ventura.(SCGCQ01378782)
- WG: unable to start VD initialization on 32 VD's when there are 240 VD created & Foreign configuration present in system.(SCGCQ01378808)
-.(SCGCQ01378812)
- WG: Error message is not proper if the username is not provided while verifying server in Manager server page.(SCGCQ01379795)
- WG:In premium features Safe ID & Serial Number needs to be highlited for better understanding.(SCGCQ01379818)
- WG: Close button can be given with a "hand" symbol in Compare and select form like all close button in other form has.(SCGCQ01380587)
- WG: Available Unconfigured drives is not formatted properly for display.(SCGCQ01380591)
- WG: Domain Authentication is shown as Default in "MAnage Server Page".(SCGCQ01380642)
- Size increment button is not working while modifying a VD that is created in MB size.(SCGCQ01380830)
- WG: "Advanced and Simple Configuration" is enabled when UG drives are "prepared for removal" and no other drives are left.(SCGCQ01380977)
- SCGCQ01383828: LSA service crashes while trying to access the IR3 controller.(SCGCQ01383828)
- WG:VD properties were not well partitioned for CacheCade - SSD config , compare to normal VD creation in HDD.(SCGCQ01384561)
- WG: Few enhancements needed in VD Expand form.(SCGCQ01389165)
- SCGCQ01389195: WG: Naming convention for VD can be made consistent for the VD's created through Advanced and Simple configuration.(SCGCQ01389195)
- Enter key is functioning as a backspace in "Set Adjustable Task Rate" - Can be disabled.(SCGCQ01389203)
- LSA mail server settings does not allow to enter name of smtp server.(SCGCQ01389204)
- WG: No. of VD's available to create is not shown properly for spanned vd's when span depth is modified.(SCGCQ01389421)
- Storcli: Battery Capacitance is displayed incorrectly across different applications.(SCGCQ01392000)
- WG: More Actions for drive is not working after staring and stopping Clear operation under Drives tab.(SCGCQ01392056)
- WG: User has to click twice on the table header to change the sorting order for any table in LSA.(SCGCQ01393336)
- Copyright link is taking to top of the page rather taking to Broadcom website.(SCGCQ01393706)
- WG: PD state info is not updated properly in the Drives tab after PD's are converted from online to offline.(SCGCQ01393771)
- WG: "Clear" and "Rescan" buttons could be highlighted for the better look in Foreign Configuration Tab.(SCGCQ01394954)
- "Add Virtual Drives" is grayed out for specific VD sizes after user presses "tab-alt" keys.(SCGCQ01398966)
- WG: Verify and Sign In Buttons are overlapping in list view in Manage Server Page.(SCGCQ01399610)
- LSA is not showing "Activate..." button for Premium Features when it is navigated after "Update Firmware" page.(SCGCQ01399670)
- WG:LSA sending email alert notifications to user which doesn't exist.(SCGCQ01418580)
- Drives under both Physical drives and Span drives tab are allowed to select simultaneously.(SCGCQ01428129)
- Login to VMware is taking at time more than 30 seconds.(SCGCQ01429431)
- Physical drives Get call taking considerably long time :it takes 5+ minutes to respond for 24 PD's in an enclosure.(SCGCQ01435908)
- WG:while editing a created VD, user cannot increase the VD size in MB .Only can decrease the size.(SCGCQ01438268)
- WG:LSA is not sorting properly the drives with different capacity of units i.e TB and GB.(SCGCQ01439751)
- WG: View server profile does not contain info on the Device id, which is sorted according to device id itself.(SCGCQ01440773)
- WG: operation of Combining JBOD drives with & without files system to move to Unconfigurued good is partially successful.(SCGCQ01440778)
- WG: Space required between two strings in the description of "Enable Drive Security".(SCGCQ01442479)
- WG: LSA Displays "Error Code:1:An user is already Logged in with Different Credentials" even user is using same credentials.(SCGCQ01442773)
- WG: LSA is changing to latest login user account though it is already logged with different User Account in different Tab.(SCGCQ01442774)
- WG: No. of UG drives are improperly updated in the Drives header tab when replace operation is triggered on a physical drive.(SCGCQ01444724)
- WG: No. Of Power Supplies info displayed is overlapping on the enclosure details. Need proper display alignment.(SCGCQ01444794)
- LSA showing 'binaryPath:./LSA' during service start in Linux.(SCGCQ01445709)
- LSA server giving null for enclosure serial number.(SCGCQ01445713)
- WG: LSA events displays invalid details for unexpected sense events.(SCGCQ01445719)
- WG: Description for event Code"579" is '0" in LSA event logs.(SCGCQ01446803)
- WG:"Disable Data Protection" is not updating in LSA until user do a manual refresh.(SCGCQ01447843)
- SCGCQ01448707: WG: LSA Event logs has enquiry info for Vendor, model and serial numbers appended with $ symbols.(SCGCQ01448707)
- WG: Inconsistency seen w.r.t making drive online while RLM is in progress.(SCGCQ01449722)
- WG: Event log page is navigating to change personality when the behavior mode is set from other tab of the same browser.(SCGCQ01450719)
- DG count is shown incorrectly in server summary page : VMware 6.5.(SCGCQ01451571)
- WG:Controller health status not updated on moving JBOD drive from offline --> online, personality : JBOD.()
- LSA Server: Handling of additional events in Cache module.(SCGCQ01451573)
- LSA: During the installation "Range of Events" selection is not reflecting in the LSA.conf file.(SCGCQ01464514)
- [lenovo 18A] [Bugzila 117507] -Reopen -The LSA doesn’t work in Suse12.3, which has many NICs.(SCGCQ01506045)
- WG: Enclosure ID is shown "Unknown" for NVMe JBOD only in event logs, Profile id=11.(SCGCQ01291162)
- WG: LSA page does not refresh on starting Full initialization on 240 VD.(SCGCQ01292183)
- Phase3 Beta PCIe: Loading SLOOB fails with error message "ExitLib failed for SAS IT Controller!! rval 0x801A".(SCGCQ01292964)
- 7.3 Client : Coverity defects check-in.(SCGCQ01308624)
- SCGCQ01309034: Coverity defect fixes check-in.(SCGCQ01309034)
- Fixed: Code maintainability issue.(SCGCQ01318344)
- coverity defect fies for : Suspicious use of non-short-circuit boolean operaton.(SCGCQ01320079)
- In Simple Config, if user select a VD and select the check box of "Assign HSP", VD size is getting changed to different size.(SCGCQ01321225)
- WG: LSA notifies user that VD will be deleted after VD erase even if the option was not selected.(SCGCQ01325795)
- WG: user notification appearing after user starts/stops the initialization on multiple VD's needs to be updated.(SCGCQ01326134)
- LSA doesn't show FW component name while FW flash operation.(SCGCQ01337028)
- WG: Multiple options of RLM are selected together for radio button used to select one of the 3 RLM operations.(SCGCQ01342615)
- LSA does not display "Link Speed" for phy 8 properly for iMR Ventura.(SCGCQ01355929)
- When the CC is scheduled as "Continuously", it is not reflected in UI after saving the changes.(SCGCQ01357007)
- Warning message has to be corrected in Foreign configuration page and one more hyperlink issue.(SCGCQ01358066)
- LSA is not taking "dot(.)" from num pad , but taking "dot(.)" form keypad while specifying the vd capacity.(SCGCQ01358908)
- Selected firmware version is coming empty for IR/IT/IMR controller.(SCGCQ01364736)
- WG: LSA displays the notification "This operation can be performed only on 32 drives at a time" 32 times.(SCGCQ01373067)
- WG: Global hotspare & Dedicated hotspare are displayed as plural entities for every hotspare listed in physical drive tab.(SCGCQ01375707)
- WG: Instance Validation failed for Spares GET URI : MR Ventura.(SCGCQ01375778)
- fixed: Min & Max of "PdRaidLevel_1E" under the "pdsForRaidLevels" is populated even though it is not supported in iMR.(SCGCQ01375817)
- WG: Other hardware tab lists wrong count of list of hardware connected when enclosure connected in multipath.(SCGCQ01376109)
- WG: View server profile contents exceed the border limits of the LSA page.(SCGCQ01378556)
- SCGCQ01378774: WG: Information of the virtual drive info and PD's involved in DG vanishes on removing & inserting the PD back from a DG.(SCGCQ01378774)
- WG: Links present in Backplane properties are so light that they look like grayed out. Needs enhancement.(SCGCQ01380680)
- WG: User is allowed to click on "Next" button even if page is not completely updated during the VD creation & RLM operations.(SCGCQ01381734)
- GUI Issues found in Advanced Configuration page.(SCGCQ01381764)
- Firmware flash message should have "new" removed from string.(SCGCQ01382062)
- LSA getting logged in , even if the password is wrong.(SCGCQ01388957)
- "%" is allowed for entering no. of seconds for locating the drives.(SCGCQ01389182)
- WG: Size limit warning is thrown if the user is giving valid size using spinner button while modifying VD.(SCGCQ01389340)
- WG: Message displayed after flashing the controller FW has to be modified for better presentation - Enhancement.(SCGCQ01389483)
- Spinner Button for increase and decrease size is not working when the size is 1.09 TB.(SCGCQ01392053)
- WG: "Username" has to be grayed out when user start typing in the login page of "Manage Server Page".(SCGCQ01393764)
- WG: UG Drives count is not updated properly after modifying a DG.(SCGCQ01393774)
- Phase 5 IT LSA - EFI-BSD version is not displayed fully when Version length is more than 12 characters.(SCGCQ01394914)
- Mismatch in enclosure properties between LSA and storecli utility.(SCGCQ01395021)
- WG: "Managing SAS Storage Link Speed" opens up on clicking help topic of "Manage PCIe Storage Interface".(SCGCQ01395075)
- when clicking on more actions for any UG drives to make DHS,the options remains as it is in LSA though the operation is done.(SCGCQ01403884)
- WG: Like "Flash Firmware" button in "Update Firmware" page, "Update" button should also have hand symbol & one more issue.(SCGCQ01405822)
- WG: while expanding exiting VD, the expand VD page is not consistent.(SCGCQ01416379)
- Fixed: WG: LSA conf does not contain the perf mode settings options configurable.(SCGCQ01422214)
- WG: Clicking on "Benefits of each MegaRAID Advanced Software Option" in premium feature is not taking to proper link.(SCGCQ01428156)
-.(SCGCQ01428383)
- LSA doesn't allow creating spanned Raid levels with 2 spans using more than 32 drives.(SCGCQ01435647)
- API performance Issues pertaining to LSA Build 004.002.000.000( VMware esxi 6.5 ).(SCGCQ01436886)
- WG : "Replace Drive "window needs improvement to look uniform.(SCGCQ01439805)
- when flashing FW with 16 mb/32 mb.ROM file , LSA throws inappropriate message.(SCGCQ01440772)
- WG: LSA displays the property Drive Security Capable as 'No' even when security is supported.(SCGCQ01442209)
- WG: the controller operations Query param : 4 has 'premium feature' and 'pinned cache' URI's GET calls in response.(SCGCQ01443879)
- WG: Confirmation Message has to be changed when more than one drives are converted from JBOD to UG state.(SCGCQ01444672)
- SCGCQ01445818: MR 7.4_Alpha_LSA does not find a server in RHEL 7.4.(SCGCQ01445818)
- WG: LSA times out after "Clear Configuration" command is issued when there is a OFFLINE DG present.(SCGCQ01447788)
- WG: Size for the VD is not updated properly when edited during VD creation.(SCGCQ01447791)
- WG: An extra "." needs to be removed in the event description for "Initialization complete on VD".(SCGCQ01449783)
- WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura.(SCGCQ01473733)
- WG: Raid 50 Vd Creation fails on unselecting drives after changing span during VD creation.(SCGCQ01309542)
- Coverity Defects - Performance Inefficiencies.(SCGCQ01313878)
- Fixed: Coverity: Class hierarchy inconsistencies.(SCGCQ01318333)
- Client: Coverty defect fixes check-in.(SCGCQ01318336)
- VD size getting increased while creating VD using simple config - Regression.(SCGCQ01341947)
- WG: Once the FW update is completed LSA shows junk character in the notification about firmware flash was successful.(SCGCQ01342536)
- SCGCQ01348082: LSA: Loopback occurs during launch. (intermittent issue).(SCGCQ01348082)
- Expand page is not closed when opened for second time.(SCGCQ01357224)
- "Add Virtual Drives" is disabled when user changes from invalid size to valid size through increment button.(SCGCQ01358299)
- WG: Error message that user encounters for Max User login, message needs to be displayed with proper message.(SCGCQ01375255)
- "Server Profile" displays blank back plane info for ctrl-1.(SCGCQ01375992)
- LSA Client : Foreign Configuration Panel issues with locked and unlocked foreign drives.(SCGCQ01378050)
- DG Actions menu is not shown properly after zooming in when VD's are hidden.(SCGCQ01380663)
- WG: Size range warning is not shown while modifying VD when unit is selected from MB to GB.(SCGCQ01380818)
- LSA Evevnt: Access policy for HIDDEN/Transport is coming as Empty.(SCGCQ01380828)
- LSA Server: User is provided with Hide and Un-Hide option though there is no HIDE performed on a VD.(SCGCQ01380845)
- WG: LSA service crashes on hiding and unhiding DG's with dedicated hotspare.(SCGCQ01380912)
- SCGCQ01383765: Resolve linux server compilation issues.(SCGCQ01383765)
- WG: Reconstruction progress is not refreshed even after the VD is cleared on which reconstruction was happening.(SCGCQ01383800)
- LSA : Silent installation is accepting the invalid options also for LSA/HPE/RWC3.(SCGCQ01389392)
- WG: Clicking on View server profile just before controller console page loads results in blank page.(SCGCQ01396731)
- WG: "DG degraded notification" is not auto-refreshed after Raid5 VD is brought from offline to online.(SCGCQ01398964)
- WG: When LSA is configured with NAT server, it is shown twice in the Remote Discovery Page.(SCGCQ01401484)
- WG: LSA is displaying loop-back address in remote discovery page while accessing LSA with IPV6 address.(SCGCQ01401546)
- WG: Hidden links present in premium features page.(SCGCQ01412883)
- WG:VD properties details need some changes to look uniform across the application.(SCGCQ01418574)
- WG: Help link for Premium Features is opening in dual tabs.(SCGCQ01428169)
- LSA: patrol reads gets initiated on all the vd's that are created though only one vd is selected.(SCGCQ01442107)
- WG:LSA is not showing the options "Pause Patrol Read|Abort Patrol Read" when PR background operation is running.(SCGCQ01442350)
- WG:when user is closing the message box for "Clear Configuration",the "X" symbol is not shown with hand symbol.(SCGCQ01442356)
- LSA service is not working in Linux.(SCGCQ01442733)
- WG: Invalid text"Each_Frehole" present in Pop up of Adding VD to existing Drive group.(SCGCQ01446454)
- WG: "Add Hot Spare" Button is enabled after selecting and deselecting the drives.(SCGCQ01448882)
- WG: LSA is not Displaying Both the Foreign Configurations (Encrypted and Unencrypted) for Import/Clear/re scan.(SCGCQ01448976)
- WG: Event with ID 552 is not updated properly. Information on Mode is empty.(SCGCQ01450725)
- LSA Client: SDS/HBA progress issue.(SCGCQ01459948)
- System x PE: LSA Does Not Support the Hyphen Character "-" In Domain Names.(SCGCQ01507989)
- LSA not giving the Un Hide All Virtual Drives operation when DG contain Hidden and normal VDs.(SCGCQ01308440)
- Coverity Defects fixes for Stream LSA7.3.(SCGCQ01311864)
- LSA7.3: Coverity defect fixes in Server code.(SCGCQ01316168)
- Coverity: Integer handling issues.(SCGCQ01318418)
- LSA Client : IR/IT Multiple Options are allowed in Update Firmware Screen.(SCGCQ01343645)
- Add hot spare page cosmetic issues.(SCGCQ01358219)
- WG:Change button is active even if button appears inactive for "Change personality", fails with an inappropriate notification.(SCGCQ01358967)
- FW last modified time is not coming properly while FW upload.(SCGCQ01359056)
- WG:while editing created vd for CacheCade - SSD Caching Configuration,the write policy tab is coming down.(SCGCQ01380641)
- WG: In "Advanced Configuration" page, Raid settings and Drive Attributes are not numbered properly.(SCGCQ01380646)
- WG: Issues pertaining to "Server is taking long to respond" LSA page.(SCGCQ01383122)
- SCGCQ01395189: WG: "Manage PCIe Storage Interface" displays empty table for MR Ventura controller with profile id 13.(SCGCQ01395189)
- WG: LSA is displaying loop-back address in remote discovery page while accessing LSA with IPV6 address.(SCGCQ01415223)
- WG: Question mark missing in "Erase" confirmation form.(SCGCQ01415923)
- WG: Extra "." (dot) has to be removed in VD Initialization confirmation message and one more cosmetic issue.(SCGCQ01428137)
- WG: Instance Validation is failing for driveGroupConfigurationService-schema.json in MR_Ventura card.(SCGCQ01443739)
- MR7.4_Alpha_LSA crashed when trying to download firmware RHEL 7.4.(SCGCQ01447240)
- LSA Client Refresh issue while making more than one drive(s) offline when RLM is in progress.(SCGCQ01449870)
- WG: No success /failure Notification is shown in server summary page on making a offline drive online.(SCGCQ01451575)
- WG:2 Spans(Modify Span Depth) is showing in "Advance configuraton" page even if their is no PD left for the config.(SCGCQ01452129)
- WG:when flashing FW with 16 mb/32 mb.ROM file , LSA throws inappropriate message.(SCGCQ01464425)
- SCGCQ01479375: LSA WebGui: "logs.txt" is generated in logs directory after fresh installation in Linux.(SCGCQ01479375)
- WG: LSA takes some time (2-3 min) in order to display the remote server page after multiple service restarts.(SCGCQ00903348)
- LSA should not allow to select the check box of VD and PD simultaneously on xSDS-None mode.(SCGCQ01323724)
- Issue : Instant Secure erase option is seen when FDE and NON-FDE drives are selected.(SCGCQ01326164)
- SCGCQ01332799: Resolve LSA server compilation issue.(SCGCQ01332799)
- LSA conf file not being updated While changing the default port 2463 and 9000 to some other free ports in windows_8.1_x64.(SCGCQ01375895)
- WG: "?" symbol is in the centre of the Drive erase page unlike in other pages.(SCGCQ01383763)
- WG: ESXi server name is not completely visible in Manage Servers page.(SCGCQ01389332)
- WG: UI Enhancement: Hand symbol has to be given for the "Modify VD" icon for better user experience.(SCGCQ01389343)
- Foreign Configuration issues locked and unlocked foreign drives count.(SCGCQ01391010)
- Action successful message needs to be modified for better User experience.(SCGCQ01392057)
- spandepth need one space between span & depth, to look uniform across the application.(SCGCQ01413225)
- Hide all Vd's in a DG is not working when there is Erase operation is in progress in one of the VD in the same DG.(SCGCQ01423352)
- LSA is not Displaying Both the Foreign Configurations (Encrypted and Unencrypted) for Import/Clear/re scan.(SCGCQ01460076)
- WG: Hide all Vd's in a DG is not working when there is Erase operation is in progress in one of the VD in the same DG.(SCGCQ01394281)
- WG: Help link for "Activate Features" after providing the Activation key is not working.(SCGCQ01398969)
- SCGCQ01424621: PD serial number getting truncated on few PDs.(SCGCQ01424621)
- Added the "?" at the end of instant secure erase. But there no issue related line in more actions panel please find the attached screenshot.(SCGCQ01442352)
- Fixed: LSA app UI cannot be opened when connect M.2 NVME SSD(via HSBP) to LSI 9460-16i/9440-8i.(SCGCQ01474461)
- 'X' symbol for removing physical drives are not highlighted when the drives are allowed to be removed.(SCGCQ01350436)
- API performance Issues pertaining to LSA Build 004.005.000.000( VMware esxi 6.5 ): Raid Mode with JBOD drives.(SCGCQ01467754)

EnhancementRequests:
- Add "Incompatible with Profile" event.(SCGCQ01289924)
- SLIR3: Change build scripts and makefiles to account for change in directory structure and new name of the library.(SCGCQ00293713)
-.(SCGCQ01389581)
- LSA Page tab name should be changed.(SCGCQ01401514)
-.(SCGCQ01416369)
- Upgrade of OpenSSL binaries to openssl-1.0.2l.(SCGCQ01444590)
- Add a new structure to provide OEMs ability to switch to select either I2C or PCIe as an out of band transport.(SCGCQ01445048)
- Update description of MR_DCMD_CTRL_PERSONALITY_SET Dcmd.(SCGCQ01467149)
- SLIR3: Remove Libsysfs dependency in StoreLibIR3.(SCGCQ00293709)
- Adding Solaris and Sparc X64 bit support in SLIR3.(SCGCQ00922699)
- Change library name to SLIT.(SCGCQ00933175)
-.(SCGCQ01309820)
- LSA Server : [Lenovo Purley] Adding tape drive support to Unified LSA for IT Ventura controllers.(SCGCQ01352474)
- HBA nvdata version in Decimal Format in LSA.(SCGCQ01365643)
- WG: Dedicated Hot spare Notification pop-up alignments.(SCGCQ01401505)
- Schedule API changes for time consuming APIs.(SCGCQ01422386)
- MR7.4: Support for FW ER:SCGCQ01389581 in LSA Server.(SCGCQ01428115)
- Update the WebServer Nginx to fix the latest Security Vulnerabilities.(SCGCQ01452493)
- SAS3 Ph8 --- Update Attribution Language - Copyright, Trademark, Confidentiality to Avago.(SCGCQ00729472)
- LSA Client: Handle Progress events without initiating individual API calls.(SCGCQ01416371)
- LSA: Make operation call with query parameter.(SCGCQ01424479)
- Add Test Link Diagnostic API.(SCGCQ01436268)
- WG: Landing page - Graphics improvements.(SCGCQ01401517)
-.(SCGCQ01412749)
- Support for FW ER:SCGCQ01389581 in LSA Client.(SCGCQ01428113)
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01563340)
- LSA7.3: LSA to hide the Empty back plane based on the property field in the LSA.conf file.(SCGCQ01312022)
- LSA: Make operation call with query parameter.(SCGCQ01416374)
- Added MR_MFC_DEFAULTS.NVMeAbortTO and MR_MFC_DEFAULTS.NVMeMaxControllerResetTO.(SCGCQ01532045)
- SCGCQ01250909 - [Lenovo Purley] - Retrieve Boot Events and Maintain it as part of Event History.(SCGCQ01291488)
- Client: EPMR12 porting to MR7.3.(SCGCQ01304973)
- Client: Provide pending profile details in LSA.(SCGCQ01331947)
- LSA Server: EPMR12 defect/feature porting to MR7.3.(SCGCQ01307382)
-.(SCGCQ01356193)
-.(SCGCQ01375857)
- WG: In Remote discovery page Self server is always listed in the last.(SCGCQ01378666)
-.(SCGCQ01472631)

CSETActivities:
- VMware LSI Out of Box driver feature reconciliation.(SCGCQ00696009 port of SCGCQ00652798)
- Provide a StoreLibIR2 deb package to work on Ubuntu.(SCGCQ00795333 port of SCGCQ00630108)
- WG: No Units are displayed for Event ID: 545: Information about super cap health.(SCGCQ01297685 port of SCGCQ01291338)
- LSA throws inappropriate error while attempt to start controller firmware upgrade when pinned cache present on controller.(SCGCQ01297819 port of SCGCQ01288364)
- CSCvd88927 - LSA is displaying drives' type string inconsistently for HDD/SSD so it needs to display consistently.(SCGCQ01331599 port of SCGCQ01316465)
- Hercules_LSA: Event ID-565 does not have any description, shows 0.(SCGCQ01336569 port of SCGCQ01313804)
- Cisco_HSW_Validation_LSA : Expand option can be taken off for degraded R5 volume.(SCGCQ01337104 port of SCGCQ01332737)
- Hercules LSA : Schedule CC button does not allow to click on the whole button.(SCGCQ01339214 port of SCGCQ01337027 )
- PR on all drives are not aborted properly until page refresh is done.(SCGCQ01342568 port of SCGCQ01340808)
- No. of steps shown in "Modify Drive Group" page is not correct.(SCGCQ01343651 port of SCGCQ01341921)
-.(SCGCQ01345364 port of SCGCQ01342479)
- Foreign Import page shows wrong data for the importable LD's.(SCGCQ01345398 port of SCGCQ01332912)
- LSA: LSA should ignore the BBU/SuperCap VPD info failures as it is not a mandatory information.(SCGCQ01347171 port of SCGCQ01346904)
- LSA: LSA should ignore the BBU/SuperCap VPD info failures as it is not a mandatory information.(SCGCQ01347220 port of SCGCQ01346908)
- LSA: LSA should ignore the BBU/SuperCap VPD info failures as it is not a mandatory information.(SCGCQ01347221 port of SCGCQ01346908)
- Cisco_HSW_Validation_LSA: "Simple Configuration" page that appears after creating a simple config is blank.(SCGCQ01347224 port of SCGCQ01345554)
- Cisco_HSW_Validation_LSA: Character limit warning for VD name is not shown while modifying the VD during VD creation.(SCGCQ01347232 port of SCGCQ01345557)
- Cisco_HSW_Validation_LSA: VD Size limit check is not working when user modifies the value of the size.(SCGCQ01350834 port of SCGCQ01346906)
- Cisco_HSW_Validation_LSA: Prepare for removal menu is still displayed even after the option is selected and event is updated.(SCGCQ01350837 port of SCGCQ01338290)
- "%" symbol followed by integer value should not be allowed for the user to enter the size during VD creation.(SCGCQ01350844 port of CGCQ01349556)
- Page scroll doesn't work after VD creation when BG processes on VD are expanded in LSA page.(SCGCQ01351383 port of SCGCQ01349487)
- VD creation fails when a partial VD is added with decimal value & with 1MB strip size to an existing DG.(SCGCQ01354306 port of SCGCQ01348005)
- Security Key provided for importing Foreign Config is not taken by LSA.(SCGCQ01369266 port of SCGCQ01331016)
- Unexpected sense PD messages are flooded in storage log when drive is in spun dwon mode.(SCGCQ01369267 port of SCGCQ01264499)
-.(SCGCQ01375259 port of SCGCQ01373451)
- LSA: Client should not show Unlock drive option if no drives are in locked state.(SCGCQ01378557 port of SCGCQ01331121)
- LSA Server: Windows Make file check-in.(SCGCQ01384621 port of SCGCQ01384618)
- RWC3 Package: Check-in of SL-IT to the package folder.(SCGCQ01384895 port of SCGCQ01384890)
- Cisco_LSA: 'vdname' parameter is missing in the event description that is generated whenever a volume property is modified.(SCGCQ01387017 port of SCGCQ01350435)
- Disabled Phy is not populated from the server when we fire /phys uri.(SCGCQ01389917 port of SCGCQ01389892)
- SCGCQ01385340: Health is not coming proper after foreign config import.(SCGCQ01389918 port of SCGCQ01385340)
- HPE: Un-installation is not removing the folder(s) after performing the Download Diagnostics operation.(SCGCQ01389925 port of SCGCQ01385453)
- WG: Message displayed after flashing the controller FW has to be modified for better presentation - Enhancement.(SCGCQ01391318 port of SCGCQ01389483)
- Hercules LSA : LD properties shows Cachecade Enabled after disabling cache cade.(SCGCQ01419753 port of SCGCQ01417215)
- WG: LSA takes some time (2-3 min) in order to display the remote server page after multiple service restarts.(SCGCQ01440910 port of SCGCQ00903348)
- MR 7.3.1_LSA fails to find server when there is no network.(SCGCQ01500133 port of SCGCQ01482320)
- Cisco - CSCvh55470 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade.(SCGCQ01566052 port of SCGCQ01562368)
- SWR: Device ID is not displayed in LSA..(SCGCQ01566241 port of SCGCQ01564621)
- Changing ini file name to storelibconfit.ini.(SCGCQ01275670 port of SCGCQ01275496)
- For phys-schema.json fails for "([0, u'properties', u'isEnabled', u'enum'], 'False ...".(SCGCQ01309844 port of SCGCQ01304900)
- LSA not allowing to create RAID with 1M strip using 4K drives.(SCGCQ01323613 port of SCGCQ01284395)
- LSA pops-up (504 : Gate Time-out) with StorCLI script to start-stop locate drives with JBOD-Hotspare conversion on.(SCGCQ01324865 port of SCGCQ01260226)
- LSA crashed on pulling out 23 drives connected with 64 LD's in multiple controllers.(SCGCQ01338337 port of SCGCQ01331755)
- Hercules LSA : Cachecade SSD caching should be "enabled" under controller properties.(SCGCQ01339133 port of SCGCQ01337029)
- Hercules LSA : WB and AWB description in LD create page not proper.(SCGCQ01339213 port of SCGCQ01337026)
- User couldn't enter his value in seconds for locating a physical drive.(SCGCQ01344082 port of SCGCQ01332742)
- Cisco_HSW_Validation_LSA: Tooltip for "Simple Configuration" is not shown when other options displays it.(SCGCQ01347225 port of SCGCQ01346851)
- Cisco_LSA: Hyperlink symbol can be shown for "Compare and select" link in Modify Drive Group.(SCGCQ01350847 port of SCGCQ01348107)
- Cisco_HSW_Validation_LSA: Naming convention can be made same across all "Virtual Drive Erase" forms.(SCGCQ01350850 port of SCGCQ01347250)
- cosmetic changes required in "Advanced configuration" page.(SCGCQ01350851 port of SCGCQ01347253)
- DG health is not populated properly in cisco cards.(SCGCQ01350892 port of SCGCQ01349625)
- Virtual Drive Erase form is not closed when it is opened for the second time.(SCGCQ01351381 port of SCGCQ01347243)
- While adding drives to any raid group, Displaying no. of available drives and selected drives can be fine tuned.(SCGCQ01351385 port of SCGCQ01348115)
- Cisco_LSA: "Background Initialization" is misspelled in Event description & one more cosmetic change is required.(SCGCQ01351454 port of SCGCQ01348041)
- In case of FW upload, LSA crash seen with big FW version name.(SCGCQ01351457 port of SCGCQ01338340)
- LSA Client: During the exclusion of the VDs from deletion of one VD leading to the deletion of all the VDs.(SCGCQ01354432 port of SCGCQ01344115)
- WG: Error message is not proper if the username is not provided while verifying server in Manager server page.(SCGCQ01387009 port of SCGCQ01379795)
- Hercules:LSA:Observe that instead of "Feedback " it is named as "FeedBack ".(SCGCQ01389091 port of SCGCQ01388943)
- Updated PD firmware version is not reflecting even after LSA refresh.(SCGCQ01392422 port of SCGCQ01382013)
- SCGCQ01385340: Health is not coming proper after foreign config import.(SCGCQ01393239 port of SCGCQ01385340)
- Hercules LSA: "Prepare for removal" feature should be disabled for drives in LSA.(SCGCQ01401490 port of SCGCQ01396735)
- Activity to check-in build files.(SCGCQ01514879 port of SCGCQ01514834)
-.(SCGCQ01520055 port of SCGCQ01508528)
- Activity to check-in AutoBST files to new MR 7.5 streams.(SCGCQ01564703 port of SCGCQ01564674)
- Updating readme file.(SCGCQ01294583 port of SCGCQ01294570)
- For spares-schema instance validation failed for "u'foreign' is not one of [u'NATIVE', u'FOREIGN', u'MIXED']".(SCGCQ01311504 port of SCGCQ01309617)
- LSA server:LSA not showing the server reboot message after profile set.(SCGCQ01316473 port of SCGCQ01316342)
- HSW_testing_LSA : Could not initialize a VD after disabling and enabling again "Initialize" option.(SCGCQ01321339 port of SCGCQ01309783)
- Cisco_HSW_Validation_LSA : Expand option can be taken off for degraded R5 volume.(SCGCQ01337071 port of SCGCQ01332737)
- Cisco_HSW_Validation_LSA: Size range warning is not shown when user is giving value beyond the limit in MB unit.(SCGCQ01352603 port of SCGCQ01352603)
- LSA not allowing to create RAID with 1M strip using 4K drives.(SCGCQ01369283 port of SCGCQ01284395)
- RWC3 Automation Script files check-in.(SCGCQ01385008 port of SCGCQ01384997)
- LSA/RWC Automation batch files check-in.(SCGCQ01386218 port of SCGCQ01386214)
- Hercules:LSA: trying to open in new tab : "Copyright @ 2017 by Avago Technologies. All Rights Reserved" loads blank page.(SCGCQ01389089 port of SCGCQ01386140)
- Adding tape drive support to Unified LSA for IT Ventura controllers.(SCGCQ01389588 port of SCGCQ01352480)
- SCGCQ01385340: Health is not coming proper after foreign config import.(SCGCQ01392429 port of SCGCQ01385340)
-.(SCGCQ01392506 port of SCGCQ01391775)
- [Lenovo 17B] - LSA- Selected Firmware version doesn't match while upgrading the FW.(SCGCQ01420040 port of SCGCQ01417199)
- Hercules:LSA: Multiple OLH links are opening when clicked on Advance configuration( IE Browser).(SCGCQ01429992 port of SCGCQ01415979)
- LSA Linux BST Automation scripts.(SCGCQ01466009 port of SCGCQ01447013)
- operations-schema.json fails for "u'percentage' is a required property..." in xSDS mode.(SCGCQ01297806 port of SCGCQ01291332)
- Hercules LSA : Auto refresh not happening on Enclosure push pull with 64 VD's configured.(SCGCQ01297821 port of SCGCQ01276760)
- SCGCQ01309545: WG: Issues pertaining to Event ID: 545: Super Cap Health event has redundant data, missing comma's.(SCGCQ01332698 port of SCGCQ01309545)
- Foreign Import page shows wrong data for the importable LD's.(SCGCQ01338335 port of SCGCQ01332912)
- Cisco Validation: FW throws an exception while scheduling Consistency check on R1.(SCGCQ01347254 port of SCGCQ01340788)
- VD size is created with improper size when user creates volume by first decreasing and increasing the size in MB unit.(SCGCQ01350833 port of SCGCQ01346860)
- WG: Hide all Vd's in a DG is not working when there is Erase operation is in progress in one of the VD in the same DG.(SCGCQ01395078 port of SCGCQ01394281)
- Wrong API populated for enclosures operations and schema will fail.(SCGCQ01445408 port of SCGCQ01444689)
- WG: LSA events displays invalid details for unexpected sense events.(SCGCQ01447743 port of SCGCQ01445719)
- WG: the controller operations Query param : 4 has 'premium feature' and 'pinned cache' URI's GET calls in response.(SCGCQ01458204 port of SCGCQ01443879)
- Cisco - CSCvg96681 - LSA-3.163 should display proper message after logout.(SCGCQ01531153 port of SCGCQ01521114)
- MR/IR: Controller Device ID value mismatch in LSA.(SCGCQ01566055 port of SCGCQ01564622)
- Hercules_LSA: Event ID-565 does not have any description, shows 0.(SCGCQ01336556 port of SCGCQ01313804)
- LSA: LSA should ignore the BBU/SuperCap VPD info failures as it is not a mandatory information.(SCGCQ01347125 port of SCGCQ01346904)
- Cisco_HSW_Validation_LSA: Credentials asked during login is not proper when login mode is set to 'Domain Login'.(SCGCQ01347233 port of SCGCQ01341930)
- Hercules-LSA : Updated PD firmware version is not reflecting automatically.(SCGCQ01393283 port of SCGCQ01392496)
- Hercules:LSA: Linux RHEL 6.9: View Event Logs Icon display not proper.(SCGCQ01414738 port of SCGCQ01409445)
- Hercules LSA: Reference to "drive group" while adding logical drive to existing array.(SCGCQ01444720 port of SCGCQ01444670)
- LSA: During the installation "Range of Events" selection is not reflecting in the LSA.conf file.(SCGCQ01472166 port of SCGCQ01472048)
- SCGCQ01479375: LSA WebGui: "logs.txt" is generated in logs directory after fresh installation in Linux.(SCGCQ01480902 port of SCGCQ01313228)
- Fixed: Drive group Migration was disabled with NVME drives DG.(SCGCQ01313228 port of SCGCQ01289586)
- LSA pops-up (504 : Gate Time-out) with StorCLI script to start-stop locate drives with JBOD-Hotspare conversion on.(SCGCQ01324864 port of SCGCQ01260226)
- Spare URI does not respond on iMR Invader.(SCGCQ01378677 port of SCGCQ01376605)
- [PA_2017B_SDV_Lenovo_x3650 M4_Storage] LSA tool update FW Image (oss: 75871) Failed for N2225 SAS HBA(Outback-2) card.(SCGCQ01408778 port of SCGCQ01408626)
- In Standalone LSA periodic automatic refresh is not happening. To display the latest status do manual refresh.(SCGCQ01411632 port of SCGCQ01397546)
- Hercules LSA : LD properties shows Cachecade Enabled after disabling cache cade.(SCGCQ01417213 port of SCGCQ01415347)
-.(SCGCQ01417223 port of SCGCQ01375862)
- LSA: Make operation call with query parameter.(SCGCQ01423429 port of SCGCQ01416374)
- MR7.3_Focused Regression_Strange character when exceeding max number of Uncof good drives on iMR.(SCGCQ01427110 port of SCGCQ01419325)
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01564577 port of SCGCQ01563340)
- LSA crashed on pulling out 23 drives connected with 64 LD's in multiple controllers.(SCGCQ01345397 port of SCGCQ01331755)
- Selected firmware version is coming empty for IR/IT/IMR controller.(SCGCQ01354345 port of SCGCQ01321474)
- Hercules LSA: Default write policy for R1 CC VD should be WB instead of WT.(SCGCQ01401352 port of SCGCQ01397557)
- [Lenovo 18A] 110340 - [PA_2017B_SDV_Lenovo_Red_Reno_Storage] Use LSA to configure M5225 and it fail to create VD's from LSA.(SCGCQ01424599 port of SCGCQ01421451)
- Hercules- LSA : VD access policy not showing as blocked for SVD on CC VD offline.(SCGCQ01443687 port of SCGCQ01442554)
- Phase 2 changes for Linux VBAS automation script.(SCGCQ01460081 port of SCGCQ01455968)
- LSA : Silent installation is accepting the invalid options also for LSA/HPE/RWC3.(SCGCQ01472265 port of SCGCQ01389392)
- CSCvd28635: LSA throws inappropriate error while attempt to start patrol read on virtual drive with SSDs.(SCGCQ01319398 port of SCGCQ01284997)
- WG: Trying to import Encrypted VD with Drive security disabled results in error code: 0x11005, it provides No Details to user.(SCGCQ01332824 port of SCGCQ01325783)
- To resolve the merge conflict.(SCGCQ01348161 port of SCGCQ01348057)
- Port Info disappears on doing Drive push pull.(SCGCQ01404636 port of SCGCQ01379323)
- Upgrade of OpenSSL binaries to openssl-1.0.2l.(SCGCQ01444595 port of SCGCQ01444590)
- LSA Windows BST Automation scripts.(SCGCQ01472059 port of SCGCQ01460401)
- LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4.(SCGCQ01557665 port of SCGCQ01555955)


3.023.000.000 - Moderate Impact
-------------

2.085.000.000 - Moderate Impact
-------------
- Fixed issue where logs incorrect when remove/insert hdd (SCGCQ01246085)
- Fixed Invalid Server Id as part of event, if server is not in network (SCGCQ01261779)
- Fixed issue where moving PD from slot 0 to another slot, PD slot ID usually still show slot 0 and slot format (SCGCQ01264554)
- Fixed issue where external enclosure serial number in not consistent between LSA, MSM and storcli (SCGCQ01268914)
- Fixed issue where LSA does not list Raid 10 as configurable raid level under configuration service uri when drive mixing is allowed (SCGCQ01037806)
- Fixed issue where Incorrect configurable Volume sizes displayed in LSA for Raid 0(SCGCQ01039518)
- Fixed issue where LSA is not un-installing through the Uninstall-LSA option through Windows All Programs (SCGCQ01039698)
- Fixed issue where VD Properties in LSA was not getting populated for default settings (SCGCQ01043610)
- Fixed issue where controllers/{id}/spares is not populated correctly (SCGCQ01056900)
- Fixed issue where LSA displays only 2 enclosures when four enclosures are connected. (SCGCQ01061548)
- Fixed issue where Enclosure more properties displays "Number of Voltage Sensors" as "0" (SCGCQ01063504)
- Fixed issue where On Number of Temperature Sensors observe that temperature mentioned has 65535 C. (SCGCQ01063924)
- Fixed issue where When the PD is in GHS state LSA is displaying the Prepare for removal option (SCGCQ01064282)
- Fixed issue where LSA does not display the access policy 'hidden' in View Event Logs. (SCGCQ01065622)
- Fixed issue where schedule patrol -read throws an error 'Invalid URI parameter' when user clicks on Finish button. (SCGCQ01066126)
- Fixed issue where Unable to migrate from secured Raid1 VD to Raid5/Raid 6 VD on LSA (SCGCQ01066154)
- Fixed issue where LSA crashes while trying to add a VD to the RAID 00 drive group. (SCGCQ01069405)
- Fixed issue where Simple configuration fails while trying to create VD using SSD Drive (SCGCQ01069412)
- Fixed issue where compared with MSM values of "Date of manufacture" and "Type" is varying. (SCGCQ01069493)
- Fixed issue where Unable to clear or import partial foreign configuration from LSA. (SCGCQ01069580)
- Fixed issue where Ventura: LSA still displays clear button as active even after successfully importing foreign configuration. (SCGCQ01069616)
- Fixed issue where IR3 Events logs are listed reverse sequence in "View Event logs" (SCGCQ01069847)
- Fixed issue where LSA Drive Tab PD "Unconfigured Good" count does not automatically refresh when we Move UG PD to JBOD and vice versa(SCGCQ01069852)
- Fixed issue where Modifying the VD during the VD creation results in option for user to allow more than one cachecade VD, Creation fails (SCGCQ01069898)
- Fixed issue where Instance validation fails for Clear Drive, Stop Clear Drive, Prepare & Undo prepare for removal due to "parameters":{}" (SCGCQ01070441)
- Fixed issue where Instance validation fails for Manage Power Save Settings, Controller PUT operation (SCGCQ01070690)
- Fixed issue where Instance Validation fails for Schedule Consistency Check (SCGCQ01070739)
- Fixed issue where Instance Validation fails for Physical Devices GET (IT controller) (SCGCQ01074960)
- Fixed issue where Server not found warning message is displaying repeatedly one over the other (SCGCQ01075026)
- Fixed issue where Backplane information not displayed under view server profile (SCGCQ01075841)
- Fixed issue where if config cleared during reconfiguration, progress bar does not clear(SCGCQ01075843)
- Fixed issue where hide on DG is not automatically updating the access policy of VDs (SCGCQ01076009)
- Fixed issue where LSA Crashes when we run API performance Script ususally when performing PD Operations GET in Large config (240 PD)(SCGCQ01076023)
- Fixed issue where "Controller Info" of LSA displays driver version of the Gateway server instead of displaying the driver of Vmware server (SCGCQ01076031)
- Fixed issue where "Application Version" in server profile page is displayed as "LSA Server null". (SCGCQ01076146)
- Fixed issue where there were multiple extra columns in PD tab (SCGCQ01077452)
- Fixed issue where the Physical devices are listed in Decreasing order of Device ID instead of ascending order in drive tab (SCGCQ01077563)
- Fixed issue where firmware update does not happen in the Direct agent system from Gateway (SCGCQ01077677)
- Fixed issue where Manage Power save settings with input of " 1 hour" fails with an error " Input Parameters are Invalid" (SCGCQ01078509)
- Fixed issue where Managed Server page provides option of adding gateway server from which we have already logged in to manage server (SCGCQ01078524)
- Fixed issue where Feedback is displayed as FeedBack in LSA. (SCGCQ01079092)
- Fixed issue where After adding server in Manage Server Page intermittently get a junk screen  (SCGCQ01079698)
- Fixed issue where back button does not work in case of Advanced Configuration During VD Creation (SCGCQ01079912)
- Fixed issues pertaining to "Set Patrol Read Properties" Number of PD Count allowed for patrol read (SCGCQ01080265)
- Fixed issue where after logging out from server that is been managed. Clicking Server again in managed server page LSA asks for credentials (SCGCQ01080448)
- Fixed issue where Instance Validation fails for PROGRESS related Operations (SCGCQ01082194)
- Fixed issue where Instance validation fails for "/controllers/0/operations/security" URI : Controller Operation POST (SCGCQ01082618)
- Fixed issue where inappropriate error message is displayed in LSA on flashing fw on IT Intruder (SCGCQ01082897)
- Fixed issue where LSA page does not automatically refresh when PD moved from UG bad to UG Good SS page, CC page does not give option (SCGCQ01083060)
- Fixed issue where on clicking save button on mail server page its shift to Alert Settings without saving that page. (SCGCQ01083063)
- Fixed issue where LSA does not show the default power save mode time set in mfc (SCGCQ01083106)
- Fixed issue where after adding server the managed server list, then logging out, new server cannot be logged into. (SCGCQ01083226)
- Fixed issue where LSA service is not present in the Windows services after downgrading LSA. (SCGCQ01084774)
- Fixed issue where Event Response is giving Default Write Policy: abc (SCGCQ01043609)
- Fixed issue where Sending Invalid HTTP verb in the request for an URI fails with 404 instead of 405 (SCGCQ01059216)
- Fixed issue where texts linked to the health icons "optimal", "critical", "needs attention", in server summary page Should be clickable (SCGCQ01063432)
- Fixed issue where LSA still displays physical disk actions and properties menu when no pd is selected after sorting from Enclosure/slot. (SCGCQ01063524)
- Fixed issue where Instance Validation fails for Simple Configuration POST (SCGCQ01064737)
- Fixed issue where consistency check Schedule parameters is available even after selecting the "Disable" from the Consistency check mode (SCGCQ01069825)
- Fixed issue where LSA not accessible through Chrome browser Version 48.0.2564.109 m (SCGCQ01078618)
- Fixed issue where while initiate ISE against 3rd party locked UG drive, XHR_Header code says "POST 200" but XHR_Response says "Er 77" (SCGCQ01080402)
- Fixed inconsistency between the VD properties displayed in STORCLI when compared with other Apps. (SCGCQ01081145)
- Fixed issue where LSA doesn't get updated without a service restart on Vmware server with IR3 controller. (SCGCQ01081324)
- Fixed issue where matching error description is not shown by client when there is a session already active during login. (SCGCQ01063542)
- Fixed issue where LSA login attempt failed for Vmware Server (SCGCQ01064784)
- Fixed issue where 002.010.000.000 build (Gateway & Standalone) is unable to discover server (SCGCQ01069396)
- Fixed issue where replace drive table does not have device Id column (SCGCQ01075112)
- Fixed issue where LSA does not update the data automatically when Delete VD is performed. (SCGCQ01079635)
- Fixed issue where RWC3-LWM (Windows) is unable to send mail to SMTP (SCGCQ01173361)
- Fixed issue where Ventura IT drive push and pull needs services restart to update the count (SCGCQ01066048, Port of SCGCQ01064904)
- Fixed issue where LSA Allows JBOD Drive having OS to be converted to UG drive, doesnt notify the user on the OS present on JBOD (SCGCQ01067253, Port of SCGCQ01052412)
- Fixed issue where LSA displays "error:Not all values are set successfully" while trying to save power save settings on IMR Ventura. (SCGCQ01067711, Port of SCGCQ01057457)
- Fixed issue where LSA shows blank screen after log in with mutiple controller in the setup (SCGCQ01069360, Port of SCGCQ01068813)
- Fixed issue where intermittent update Ventura firmware hang using LSA ( StorCLI is OK ) (SCGCQ01069565, Port of SCGCQ01038421)
- Fixed issue where user unable to migrate from secured Raid1 VD to Raid5/Raid 6 VD on LSA (SCGCQ01070807, Port of SCGCQ01066154)
- Fixed issue where all the events are not getting downloaded while downloading log from LSA (SCGCQ01145261, Port of SCGCQ01139334)
- Fixed issue where no error message is displayed while importing secure EPD through wrong key (SCGCQ01066088, Port of SCGCQ01063911)
- Fixed issue where user unable to clear or import partial foreign configuration from LSA. (SCGCQ01085466, Port of SCGCQ01069580) 

2.030.000.000 - New Function Only/No fixes
-------------





Lenovo Data Center Group Linux OS Support Home Page
linux.lenovo.com

© 2018-2021 Lenovo. All rights reserved

StorCLI command line tool (For Linux)



StorCLI (Command Line) Utility for Storage Management

Adapters Supported:
 	ThinkSystem RAID 530-8i PCIe 12Gb Adapter  (7Y37A01082)
	ThinkSystem RAID 530-4i Flex Adapter       (7M17A03932)
	ThinkSystem RAID 530-4i Flex Adapter       (7M27A03918)
	ThinkSystem RAID 530-8i Dense Adapter      (SD530 RAID)
	ThinkSystem RAID 530-16i PCIe 12Gb Adapter (4Y37A09727)
	ThinkSystem RAID 730-8i 1GB Cache PCIe 12Gb Adapter  (7Y37A01083)
	ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter  (4Y37A09722)
	ThinkSystem RAID 930-8i 2GB Flash PCIe 12Gb Adapter  (7Y37A01084)
	ThinkSystem RAID 930-16i 4GB Flash PCIe 12Gb Adapter (7Y37A01085)
	ThinkSystem RAID 930-24i 4GB Flash PCIe 12Gb Adapter (7Y37A01086)
	ThinkSystem RAID 930-8e 4GB Flash PCIe 12Gb Adapter  (7Y37A01087)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M17A03933)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M27A03917)
	ThinkSystem  RAID 930-16i 8GB Flash PCIe 12Gb Adapter(4Y37A09721)
	ServeRAID M1210 SAS/SATA Controller    (00JY194)
	ServeRAID M1215 SAS/SATA Controller    (46C9114)
	LSI SAS3004 RAID                       (NA-SAS3004-B)
	LSI SAS3004 RAID                       (NA-SAS3004-N)
	ServeRAID M5210 SAS/SATA Controller    (46C9110)
	ServeRAID M5225-2GB SAS/SATA Controller(00AE938)
	ServeRAID M5215 with 2GB Flash Enablement Flex System x240 M5   (00JX142)
	ServeRAID M5210e SAS/SATA Controller   (46C9117CTO)
	ServeRAID M5120 SAS/SATA Controller    (81Y4478)
	IBM Flex System Storage Expansion Node (68Y8588)
	ServeRAID M5115 SAS/SATA Controller for Flex System  (90Y4390)
	ServeRAID M5100 Series IBM Flex System Flash Kit for X6 (44T1178)
	ThinkSystem RAID 940-8i 4GB Flash PCIe Gen4 12Gb Adapter  for 4Y37A09728
	ThinkSystem RAID 940-8i 8GB Flash PCIe Gen4 12Gb Adapter  for 4Y37A09729
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Adapter  for 4Y37A09730
	ThinkSystem RAID 940-32i 8GB Flash PCIe Gen4 12Gb Adapter  for 4Y37A09733
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Internal Adapter  for 4Y37A09735


NOTE TO SERVICE - Reference RETAIN #N/A

007.1707.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------- 
MR 7.17

Defects:
-StorCLI listing failed NVMe drives in non-sorted order.(DCSG00320844
-Instance Validation Failed for "/call/fall show all.json" and foreign-configuration-detailed-schema.json.(DCSG00408509
-MR7.16_storcli: VD creation with the remaining drives fails.(DCSG00303606
-Enclosure position is showing as - for drive detailed properties on an IT controller.(DCSG00286693
-Package Version is not displayed properly after flashing firmware..(DCSG00961822
-PH18 BETA - StorCLI - Update YEAR in the CLI banner.(DCSG00707142
-Storcli launch fails with permission denied message.(DCSG00972016
-Setting CC date and time exceeding the limit, needs to be handled.(DCSG00520110
-"rval - 0" is displayed for "show phyerrorcounters" command..(DCSG00337710
-Storcli lists "/ex show all" for "/cx show all" command..(DCSG00417504
-DiskGroup show all list Hostpare in Unconfigured drive list.(DCSG00359247
-Storcli: learnStartTime displayed incorrectly in command details.(DCSG00320649
-Storcli /cx set debug reset all help description needs an update.(DCSG00521571
-storcli /cx set flushwriteverify help needs an update.(DCSG00507067
-PH17 PA - StorCLI ARM - show file command displays incorrect output for BIOS image.(DCSG00315152
-PH18 PA - StorCLI - appropriate message needed for erase all excludemfg command.(DCSG00395234
-Storcli shows "success" with incorrect message INSTEAD of syntax error for "/c0/d1 set" command..(DCSG00543505
-storcli show alilog shows "SATA-3G" as device interface for 9361-16i.(DCSG00555672
-Handling PBLP component whild displaying Image component versions.(DCSG00301878
-MR_7.17: After Driver unload/load via DDV tools- Ctrl acces via Storcli exit with Segmentation Fault.(DCSG00426317
-coverity: fixing non-array delete and dereferencing before NULL checks.(DCSG00368376
-Handling the read-only file system from storcli.(DCSG00542683
-Updating new SPDM MPI errors.(DCSG00435039
-"Failed Drive not found" reported from enclosure level show repair command.(DCSG00423496
-Controller Lane show command is not working with individual Lanes.(DCSG00386181
-Storcli show command is not displaying remaining drives when PD info fails for one drive.(DCSG00469639
-VD creation fails from storcli even though free capacity is present in DG.(DCSG00757768
-Aero 7.15 CLI shows a extra space in the /c0 set cc h command.(DCSG00298943
-Instance Validation Failed for "/call show" and controller-properties-schema.json.(DCSG00408497
-show alilog command displays JBOD as volumes.(DCSG00556934
-Instance Validation Failed for "/call/fall import preview.json" and foreign-configuration-detailed-schema.json.(DCSG00408512
-Max commands for averaging needs to be removed from DPMstat RA output.(DCSG00286349 (Port Of Defect DCSG00306711)
-Failure observed while running set sbr command.(DCSG00779151 (Port Of Defect DCSG00932922)
-Storcli "/call/eall/sall download status" error message needs correction..(DCSG00735452 (Port Of Defect DCSG00757676)
-Unified StorCLI MR7.15 - Fixing coverity issues - Part 1.(DCSG00290662 (Port Of Defect DCSG00368612)
-Atlas 4.2: StorCLI lists wrong error message "Failed in standard Inquiry", when user tries to upgrade/downgrade all connected NVMe Drives FW at a time.(DCSG00309398 (Port Of Defect DCSG00313432)
-The foreign config of DHS/GHS details is not listing under foreign config import preview.(DCSG00919659 (Port Of Defect DCSG00935761)
-Invalid Array Size in ZB is displayed for Degraded R1 span Foreign VD in storcli foreign import preview.(DCSG00916209 (Port Of Defect DCSG00935751)
-Logical ID of Cobra expander not displayed properly in Storcli and LSA.(DCSG00342456 (Port Of Defect DCSG00391477)
-CLI crashes when issuing the phyerrorcounters command on a 14G Expander backplane.(DCSG00323054 (Port Of Defect DCSG00323721)
-Show command status not proper when issued with wrong EID.(DCSG00906544 (Port Of Defect DCSG00935762)
-Storcli shows no output for valid parameter for "/c0/p0,1,22 show" command..(DCSG00840944 (Port Of Defect DCSG00932927)
-From the CLI failed to convert UBAD state drive to UGOOD.(DCSG00391494 (Port Of Defect DCSG00391509)
-Non Foreign drives GHS are listing under Foreign import preview.(DCSG00931210 (Port Of Defect DCSG00935765)
-Storcli "show file" command does not report correct FW version.(DCSG00299788 (Port Of Defect DCSG00302030)
-Storcli show incorrect property name for "/c0/d0,3 set hidden=off" command..(DCSG00733214 (Port Of Defect DCSG00758467)
-Coverity fixing bad allocator and resource leaks.(DCSG00307346 (Port Of Defect DCSG00307355)
-Vses Device Type is displayed as Enclosure for IT card.(DCSG00920244 (Port Of Defect DCSG00935772)
-StorCLIF fail to flash firmware image of BTBL (BOOT_BLOCK) on Invader MR.(DCSG00330381 (Port Of Defect DCSG00353198)
-Storcli throws junk value is shown on set consistency check.(DCSG00906989 (Port Of Defect DCSG00935693)
-MR 7.15 StorCLI : Addressing Coverity defects.(DCSG00286677 (Port Of Defect DCSG00311222)
-CLI Version info is seen in continuation of Sense data when executed show events.(DCSG00935802 (Port Of Defect DCSG00935973)
-VDs imported from Jbod mode to RAID do not have OS name available in Linux OS.(DCSG00968023 (Port Of Defect DCSG00975216)
-CLI failing to stop a BGI or CC when paused..(DCSG00735544 (Port Of Defect DCSG00757870)
-Enclosure phyerrorcounters fails in VMware platform.(DCSG00706496 (Port Of Defect DCSG00706497)
-Storcli shows success for "set patrolread excludevd" command failure in the presence of VD..(DCSG00906735 (Port Of Defect DCSG00935770)
-For empty SPDM slots 0 & 1 show security slot info command shows as Invalid data on IT controller..(DCSG00348125 (Port Of Defect DCSG00353186)
-Segmentation fault noted with drive firmware update.(DCSG00758645 (Port Of Defect DCSG00932904)
-VD creation output shows VD size as 0KB when it reaches maximum supported virtual disks(64VDs) in a DG..(DCSG00349415 (Port Of Defect DCSG00353914)
-SAS drive Inquiry data is not shown in drive show all output.(DCSG00778367 (Port Of Defect DCSG00932917)
-Fixing Coverity defects of MR 7.15.(DCSG00299981 (Port Of Defect DCSG00309219)
-Post reboot incorrect lane speed is displayed in Storcli when user sets it to 16GT/s.(DCSG00383336 (Port Of Defect DCSG00395901)
-On storcli /c0/v1,2,3,4 del if anyone of the vd in the series is not present then all the vd's are not deleted.(DCSG00264571 (Port Of Defect DCSG00266888)
-Coverity defects - remove resource leaks, invalid types in function arguments.(DCSG00269017 (Port Of Defect DCSG00277861)
-Storcli will not show LargeIOsupport is enabled/disabled on the controller.(DCSG00353195 (Port Of Defect DCSG00353882)
-Storcli shows target id of the drive as boot drive instead of showing drive slot number for JBOD drives..(DCSG00344079 (Port Of Defect DCSG00353203)
-MR7.15_storcli: With the latest storcli, VD creation with the remaining drives fails.(DCSG00278049 (Port Of Defect DCSG00282590)
-Removed leading spaces for SATA drives.(DCSG00904104 (Port Of Defect DCSG00935692)
-Drives connected to IT controller reports Shield Counter.(DCSG00244631 (Port Of Defect DCSG00266881)
-Size of Degraded R10 Foreign VD is displayed as 0 KB in storcli.(DCSG00916207 (Port Of Defect DCSG00935746)

EnhancementRequest:
-Adding new License file and updating the build script to include the new file.(DCSG00324401
-Add CLI command to control Parity Read Cahce Bypass for SSD VDs.(DCSG00342282
-MR7.16 : Support WJ Pinning for both WB and WT Parity RAID VDs.(DCSG00214472
-Provide option in storcli to disable / enable the Preboot trace Buffer feature in MR FW..(DCSG00310366
-Enable cache retention testing on Shenandoah controllers for factory testing.(DCSG00340899
-Updating storcli code and makefiles to support VBAS builds on GCP.(DCSG00412063
-Additional NameSpace behavior changes.(DCSG00310386
-Updating storcli BST scripts to support new VBAS Auto BST procedure.(DCSG00282976
-StorCLI: Automate the test cases specific to MR7.17 Product Requirements.(DCSG00433350
-Add support for reporting SPDM Measurement Specification and Hash Algorithm.(DCSG00301782
-Updating command legends as per the command output.(DCSG00083851
-IT Drive Model Number , Revision for SATA drives displayed in full.(DCSG00371061
-MR7.16: StorCLI does not show the SAS Address of the enclosure.(DCSG00255109
-Unified StorCLI 7.17 - x64 UEFI VBAS / GCP support.(DCSG00559813
-Updating Error Strings for NVME init error codes in Apps.(DCSG00434066
-MR7.16 StorCLI: Ruby SED Support.(DCSG00264744
-CLI to handle ERROR_BUSY from Windows storport.(DCSG00348813 (Port Of EnhancementRequest DCSG00353214)
-Displaying "OS name" for VDs imported from EHBA mode to RAID.(DCSG00775114 (Port Of EnhancementRequest DCSG00932911)
-Display Enclosure serial No in Storcli.(DCSG00500922 (Port Of EnhancementRequest DCSG00932906)
-Request to add checks (DevId, SubDevice Id) check prior to flashing.(DCSG00500924 (Port Of EnhancementRequest DCSG00521828)
-SEKM Support in CLI.(DCSG00433143 (Port Of EnhancementRequest DCSG00935780)
-CLI: Package Stamping Verification During Firmware Update.(DCSG00239672 (Port Of EnhancementRequest DCSG00282815)
-StorCLI has the ability to switch the OOB mode.(DCSG00547179 (Port Of EnhancementRequest DCSG00935783)
-SMART Polling Improvement - PERC 10.(DCSG00249963 (Port Of EnhancementRequest DCSG00282814)
-PERCcli turn off logging by default.(DCSG00255367 (Port Of EnhancementRequest DCSG00282813)
-Remove the MFG date, Revision date and Rev from IT StorCLI output.(DCSG00415059 (Port Of EnhancementRequest DCSG00418372)
-Display port information for NVMe Init failed drives.(DCSG00359418 (Port Of EnhancementRequest DCSG00421187)
-storcli "set good" command can still be used for JBOD EPD-PT drives.(DCSG00318591 (Port Of EnhancementRequest DCSG00353919)
-PERC11.1 - Dual x8 Support for 16 port Controllers.(DCSG00299060 (Port Of EnhancementRequest DCSG00323772)

007.1513.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------- 
MR 7.15

Defects:
-CLI Version info is seen in continuation of Sense data when executed show events.(DCSG00935802)
-Handling the read-only file system from storcli.(DCSG00938327 (Port Of Defect DCSG00542683))

Enhancements:
-Request to add checks (DevId, SubDevice Id) check prior to flashing.(DCSG00930193 (Port Of EnhancementRequest DCSG00500924))


007.1510.0000.0000  - Moderate Impact/Low Probability of Occurrence
-------------------- 
MR 7.15

Defects:
-From the CLI failed to convert UBAD state drive to UGOOD.(DCSG00391494)
-PH17 PA - StorCLI ARM - show file command displays incorrect output for BIOS image.(DCSG00320641 (Port Of Defect DCSG00315152))
-StorCLI listing failed NVMe drives in non-sorted order.(DCSG00321815 (Port Of Defect DCSG00320844)
-MR 7.16: Storcli: learnStartTime displayed incorrectly in command details.(DCSG00321908 (Port Of Defect DCSG00320649))
-rval - 0" is displayed for "show phyerrorcounters" command..(DCSG00337735 (Port Of Defect DCSG00337710))
-DiskGroup show all list Hostpare in Unconfigured drive list.(DCSG00360517 (Port Of Defect DCSG00359247))
-Controller Lane show command is not working with individual Lanes.(DCSG00386184 (Port Of Defect DCSG00386181))
-storcli /cx set flushwriteverify help needs an update.(DCSG00541982 (Port Of Defect DCSG00507067))
-"Failed Drive not found" reported from enclosure level show repair command.(DCSG00430578 (Port Of Defect DCSG00423496))
-Storcli show command is not displaying remaining drives when PD info fails for one drive.(DCSG00489855 (Port Of Defect DCSG00469639))
-Storcli /cx set debug reset all help description needs an update.(DCSG00538790 (Port Of Defect DCSG00521571))

EnhancementRequest:
-Display Enclosure serial No in Storcli.(DCSG00500922)
-IT Drive Model Number , Revision for SATA drives displayed in full.(DCSG00405900 (Port Of EnhancementRequest DCSG00371061))


007.1326.0000.0000  - Moderate Impact/Low Probability of Occurrence
-------------------- 
Defects:
-Foreign Config Preview shows empty data when Foreign config is present with Rebuild is in Progress.(DCSG00261203)
-Inconsist DG number in StorCLI.(DCSG00235157)
-RTTdump shows success but it fails to download the dump..(DCSG00253652 (Port Of Defect DCSG00253719))
-Incorrect Adapter type shown in the perccli show all output.(DCSG00241405 (Port Of Defect DCSG00244145))
-Expander firmware download using with mode 5 option fail with error message..(DCSG00239524 (Port Of Defect DCSG00240685))
-With length command, CLI says Memory Exhausted.(DCSG00235628 (Port Of Defect DCSG00236791))
-Enclosure position is showing as - for drive detailed properties on an IT controller.(DCSG00286693 (Port Of Defect DCSG00286701))
-Observe CLI Crash on windows while setting Autoconfig option.(DCSG00253642 (Port Of Defect DCSG00253722))
-MR7.15_storcli: With the latest storcli, VD creation with the remaining drives fails.(DCSG00278049 (Port Of Defect DCSG00282592))
-"No Controller found" shown when controller is busy..(DCSG00248017 (Port Of Defect DCSG00253661))
-On storcli /c0/v1,2,3,4 del if anyone of the vd in the series is not present then all the vd's are not deleted.(DCSG00264571 (Port Of Defect DCSG00266886))
-Connector Name is incorrectly displayed when connector count goes beyond 8.(DCSG00249023 (Port Of Defect DCSG00252701))
-MR 7.15: Storcli: Instance Validation Failed for "virtual-drive-config-schema.json" and "/call delete config force".(DCSG00247992 (Port Of Defect DCSG00253761))
-With new MR API changes, storcli shows failure while changing accesspolicy.(DCSG00257307 (Port Of Defect DCSG00258140))
-MR 7.15: Storcli: Instance Validation Failed for "enclosure-fw-download-schema.json" and "enclosure FW download" output..(DCSG00250066 (Port Of Defect DCSG00253733))
-Show expansion shows wrong output in presence of JBODs..(DCSG00247163 (Port Of Defect DCSG00252417))
-Enclosure position value not listed properly in show all command.(DCSG00254935 (Port Of Defect DCSG00256384))
-Drives connected to IT controller reports Shield Counter.(DCSG00244631 (Port Of Defect DCSG00266894))
-Expander firmware download help need to be corrected for IT controller..(DCSG00239870 (Port Of Defect DCSG00240680))

EnhancementRequests:
-To add return status MFI_STAT_OK_REBOOT_REQUIRED to MR_DCMD_LD_SET_PROPERTIES in mr.h.(DCSG00256271)
-Additional FDE type for Ruby SED support.(DCSG00055878)
-MFI SMP Port Num API changes.(DCSG00257777)
-MR7 API: Add package incompatibility reporting.(DCSG00231443)
-SMART Polling Improvement - API Changes.(DCSG00246317)
-Implement customSign.exe CLI wrapper utility to help customers sign with their private key.(DCSG00234646)
-Changes to support 16port connection to Expander with AeroIOC.(DCSG00254845)
-Updating storcli BST scripts to support new VBAS Auto BST procedure.(DCSG00282976 (Port Of EnhancementRequest DCSG00290359))

007.1325.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------  
MR 7.13
Fix issue:
DCSG00235157 - Inconsist DG number in StorCLI
Description:
Customer reported the DG/Array/Row is incorrect to get from storcli and it causes "insert" command failure. 

007.1324.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------  
MR 7.13
Defects:
-Storcli: Optl not mentioned in /call/dall show output..(DCSG00065740)
-Instance Validation Failed for "/call set smartpollinterval=300" and controller-smartpollinterval-schema.(DCSG00057141)
-StorCLI crash when create VD.(DCSG00052275)
-/e: and /s: is not mentioned in the Convention for /storcli64 /c0/v0 start migrate detailed ?.(DCSG00143788)
-BZ(186687):[AMD2P & Whitley] EXSi 7 can't boot up after install storcli.(DCSG00048516)
-Storcli show Device type as backplane while no drives are connected.(DCSG00074732)
-Help Description for Migrate shows "operation" printed twice in Storcli output..(DCSG00063696)
-Instance Validation Failed for "/call show" and controller-properties-schema.json.(DCSG00057213)
-Coverity analysis - Fixing uninitialized variables, resource leaks, and return statements - Part 1.(DCSG00046195)
-Foreign topology table display BT as "Y" for drives which are in foreign state..(DCSG00068453)
-Storcli: Same help description across "/c0/e0 show" and "/c0/e0 show all"..(DCSG00064748)
-While executing perccli, by default log file with storcli.log is getting generated..(DCSG00038031)
-MR 7.13: Storcli(Regression): Syntax error seen while using "nolog" and "page" together as parameters.(DCSG00071417)
-In Aero behind atlas configuration "NVME" drive firmware revision shows wrong.(DCSG00049614)
-Storclif command for battery retention test issues command to start retention test which is an unsupported command.(DCSG00058688)
-Show DPM with type LCT is not giving proper output and register DPM commands for all OS.(DCSG00033459)
-Storcli: ProdID Legend abbreviation missing in /c0/eall show output..(DCSG00063317)
-FW sometimes allows an invalid CLI command (set personality=HBA) to be successful and sets the personality to eHBA mode.(DCSG00129542)
-Fixing Coverity defects.(DCSG00044004)
-Unable to create JBOD using the legacy command with latest Perccli.(DCSG00118670)
-MR 7.13: Storcli: GHS is shown as revertible.(DCSG00065815)
-In the presence of Locked Foreign config, "/c0/fall del" shows incorrect output..(DCSG00062615)
-StorCLI - '/c0 show nolog' reported as Un-supported Command.(DCSG00071410)
-Set VD policy to WB (unsupported )should return failure in JBOD personality..(DCSG00076992)
-Shenandoah_MRSA: Enclosure Bay count coming Wrong in CLI.(DCSG00074731)
-Shenandoah_Storcli : Legend for ID in JBOD list is missing.(DCSG00069312)
-Incorrect Legend abbreviation in storcli show output.(DCSG00058874)
-MR 7.13: Storcli: controller add commands are listed along with vx commands..(DCSG00065744)
-Even on giving wrong 'storclif delete config' command syntax, the config is cleared successfully without any error.(DCSG00055164)
-Storcli.efi shows incorrect note for unsupported commands for MR controllers.(DCSG00056335)
-VMware peccli, percli64 and storcli64 bit binary loads library from storcli 32 bit's installation path.(DCSG00074600)
-StorCLI - /c0/eall/sall start locate not working for second enclosure connected.(DCSG00040244)
-Instance Validation Failed for "/call show dpm" and controller-dpm-schema.json.(DCSG00057194)
-Command description should be modified for storclif /cx set activityforlocate=.(DCSG00069746)
-MR 7.13: Storcli: bbu not described in convention details.(DCSG00066314)
-Shenandoah_storCLI: Add vd command for r0 getting successful with 512KB when mazStripeSize is 1MB.(DCSG00057003)
-Fixing Coverity defects, uninitialized, unused variables and memory leaks.(DCSG00052049)
-Start_entry is not a command parameter in show events command.(DCSG00067937)
-On OS /cx/dall split mirror command shows success when there is no drive groups.(DCSG00069690)
-Update the storcli readme with for Esxi 6.x and Esxi 7.0 releases.(DCSG00055533)
-Extended the abbreviation in the legends.(DCSG00069703)
-Shenandoah : storcli : Energy Pack show present for MR 216i controller , where the hardware is not supported.(DCSG00053888)
-"set sbr" command mentioned in detailed help but not listed in help output..(DCSG00068444)
-Creation of VD for with more than 64 drives is failing with "Cannot create configuration with x drives".(DCSG00056544)
-Description of compare firmware ver command does not mention as IT supported command.(DCSG00070258)
-Command description should be modified for /cx set alarm command.(DCSG00069709)
-MR 7.13 : RSOD is seen for storcli.efi show command when the controller is in invalid state.(DCSG00066879)
-StorCLI /cx restart is not supported in UEFI environment should be mentioned in help..(DCSG00068879)
-Remove deprecated command 'show adpcount' from Ubuntu folder(readme).(DCSG00058329)
-Segmentation fault seen while running OCR and Patrol read in loop on ESXi7.0 OS..(DCSG00066854)
-Instance Validation Failed for "/call/fall import preview" and foreign-configuration-detailed-schema.json.(DCSG00068868)
-Field for CV is missing in table as well as in legend for storcli64.exe show command.(DCSG00067075)
-Restrict discovery of PERC HBA through StorCLI(Static binary).(DCSG00077037)
-PH14 Alpha Aero - StorCLI - Difference in output noted for /cx/px set state command.(DCSG00055119)
-MR 7.13 : Enclosure Device ID is mentioned in the legend for /cx/vall show command.(DCSG00067878)
-MR 7.13 : Cosmetic issue is seen in the command name of /cx /cx show memscrubpatterns ?.(DCSG00067877)
-Commands displayed twice in help description..(DCSG00068441)
-Storcli DPM does not use legend "Resp" in EXT output.(DCSG00060706)
-Enclosure ID is not mentioned as optional in "add Vd " command.(DCSG00058867)
-Port information coming as internal and Location as Blank in when all the drives are removed from UBM2 Backplane.(DCSG00071756)
-DPM delete help is listed under drive delete command group.(DCSG00053537)
-No mention on convention in restart command description..(DCSG00068542)
-Fixing Coverity defects - Uninitialized variable, resource leaks and null referencing.(DCSG00041202)
-Set the PR to run on only configured array, but it complete the PR along with un-configured area..(DCSG00067103)
-Fixing Coverity issues - Resource leaks.(DCSG00054690)
-Storcli throws incorrect error message for /c0 add vd each r0 when Ubad drive is present in the setup..(DCSG00069698)
-Use NVRAM to save PTB information -- API changes.(DCSG00082981)
-Debug logs in FreeBSD is logging timestamp in different lines.(DCSG00069730)
-"/c0 show nolog" shows as "un-supported command.(DCSG00068482)
-Shenandoah_Storcli : The status of PD FW update on multiple drives is not proper when parallel is not included.(DCSG00069693)
-Device type of UBM backplane is displayed as expander in Valvano-32i Controller managed port(C3)..(DCSG00054275)
-Shenandoah_PA2:StorCLI not branding compliant for VD creation command Failure case -IO Policy specif.(DCSG00049610)
-Storcli: px is not described in convention details..(DCSG00065742)
-Unmap enabled not listed for unmap enabled VDs with /cx/vall show all cli command.(DCSG00112331)
-Instance Validation Failed for "storcli64.exe show" and system-schema.json.(DCSG00057156)
-Not able to create R1/R10 with 1MB size and strip size is 1MB.(DCSG00058162)
-Description for storcli output is not proper after collecting the snapdump with id=all.(DCSG00063626)
-StorCLI not reporting default oob settings from nvdata value.(DCSG00066530)
-Executing storcli commands from external path throws error.(DCSG00072117)
-StorCLI: /storcli /cx add vd verbose help ,strip size 512 is missing in help description under strip sizes..(DCSG00146343)
-MR 7.13: Storcli: Caution mentioned instead of note..(DCSG00066554)
-perccli is Reporting incorrect scheduled BBU Learn Date.(DCSG00109638)
-Coverity analysis - Fixing uninitialized variables, resource leaks, and return statements.(DCSG00046460)
-Storcli64.exe /c0 show freespace shows unnecessary data when freespace is not present.(DCSG00055686)
-Schema mapping list is not updated with DPM commands.(DCSG00057823)
-Foreign DHS drive state is displayed as UGood under /c1/fall show all tab..(DCSG00068427)
-MR 7.13: Storcli: logfile is not described in show dpmstat command..(DCSG00065838)
-Statistics is spelled as Statitics in dpm stat commands.(DCSG00057112)
-Cache Vault should be placed instead of battery for "storcli /cx/cv show status ?" help.(DCSG00143868)
-Exit code showing "0" for failed storCLI command due to syntax error.(DCSG00054313)
-Removal of log type from storcli logs.(DCSG00046794)
-Discription for the term "NoVDs" is missing in the legends.(DCSG00068592)
-start dpm returned error.(DCSG00035436)
-Storcli: Show latest events output print shows 0.00 for all the number of events dumped (expected is the number of events queried for).(DCSG00068877)
-Incorrect message noted when Ventura firmware flashed on Aero board.(DCSG00046031)
-No consistency in the help details of "/c0/ex download" commands.(DCSG00064745)
-Storcli license file is not present in the Vmware, Ubuntu & EFI folders.(DCSG00056538)
-Storcli issuing 'add vd r0 drives=all' causes storcli to crash.(DCSG00053963)
-No syntax error for multiple usage of "nolog" parameter in the command..(DCSG00066729)
-Re-Host information is blank when ASO is not enabled.(DCSG00072628)
-SSD Wear guage Parameter "SSD Percent used" to be removed from CLI.(DCSG00074791)
-MR 7.13: Storcli: sx not described in convention details..(DCSG00066310)
-Error message is improper for invalid raid level in volume creation.(DCSG00081057 (Port Of Defect DCSG00083789))
-Set MFG command does not throw an error when executed with empty file..(DCSG00074178 (Port Of Defect DCSG00074209))
-VD delete command works with multiple force options.(DCSG00165527 (Port Of Defect DCSG00167329))
-Syntax error for /c0 show AliLog ?.(DCSG00109790 (Port Of Defect DCSG00112470))
-storcli faults when issue drive poh command on Linux.(DCSG00075870 (Port Of Defect DCSG00075875))
-show memscrubpatterns shows status as success but failed in the description.(DCSG00077082 (Port Of Defect DCSG00103214))
-PH15 PA StorCLI - Segmentation fault observed when Sea IT PSOC image flashed on Ventura.(DCSG00075626 (Port Of Defect DCSG00212680))
-Wrong enclosure details are displayed when slot details are queried..(DCSG00127133 (Port Of Defect DCSG00139981))
-Storcli_VMWare gives failure messages when user tries to set the lanespeed.(DCSG00167210 (Port Of Defect DCSG00167280))
-"Download cpld" command displays incorrect output for MR controller..(DCSG00075734 (Port Of Defect DCSG00075863))
-The properties displayed in the command show htbparams has misspelled fields.(DCSG00104056 (Port Of Defect DCSG00105681))
-Instance Validation Failed for "/call/fall show" and foreign-configuration-schema.json.(DCSG00076415 (Port Of Defect DCSG00078173))
-storclif.exe /cx set copyback ? shows incorrect command name..(DCSG00075718 (Port Of Defect DCSG00075890))
-No description mentioned for "/cx set eghs" command..(DCSG00074290 (Port Of Defect DCSG00074768))
-Unified StorCLI Phase 15: storcli64 /cx add vd each help file missing options and format inconsistencies.(DCSG00139659 (Port Of Defect DCSG00139995))
-Aero Controller DPM does not report Max Response Time under 1 ms..(DCSG00099365 (Port Of Defect DCSG00102548))
-Storcli: Wrcache is mentioned instead of WT| WB.(DCSG00074284 (Port Of Defect DCSG00074767))
-Storclif allows to set Set SubOEMID as 1000 and more.(DCSG00079932 (Port Of Defect DCSG00080836))
-Description for storcli output is not proper after collecting the snapdump with id=all.(DCSG00031711 (Port Of Defect DCSG00063602))
-Storcli /cx show cc , does not shows the "Unit" for CC execution Delay..(DCSG00126229 (Port Of Defect DCSG00129753))
-storcli64.exe /c0/e1/s1 start sanitize throws syntax error..(DCSG00129738 (Port Of Defect DCSG00129750))
-forcehcb is executed with incorrect description in OS level..(DCSG00080961 (Port Of Defect DCSG00083295))
-"Show alilog" command output shows invalid PD ID in Virtual drive info..(DCSG00167354 (Port Of Defect DCSG00167449)
-force is not defined under OPTIONS in storcli64 secureerase help file.(DCSG00148255 (Port Of Defect DCSG00150480))
-Storcli displays "Returned SCSI status for the command : Check condition" along with regular command.(DCSG00138580 (Port Of Defect DCSG00139200)
-Aero Alpha: Storcli stops functioning during run of attached script.(DCSG00034379 (Port Of Defect DCSG00039682)
-/vx is mentioned in the convention for storclif64.exe /cx set cc detailed ?.(DCSG00075700 (Port Of Defect DCSG00075894))
-DCSG00096587.(DCSG00104055 (Port Of Defect DCSG00108742))
-Avenger: ./storcli2 /c0 show ds all command(not present) shows the output of /c0 show all.(DCSG00061163 (Port Of Defect DCSG00080485)
-PATH_1 and PATH_BOTH assigned drives not getting displayed under storcli in WF DDROCK setup.(DCSG00050891 (Port Of Defect DCSG00079275))
-Storcli output starts with "GetCtrlInfo : ProcessLibCommand failed; retCode = 0xFF" for all command.(DCSG00214170 (Port Of Defect DCSG00214248))
-"OS Drive Name" does not display the details in "vall show all" for esxi OS.(DCSG00102559 (Port Of Defect DCSG00103190))
-Storcli: "show bbmt" displays output for an invalid VD..(DCSG00228667 (Port Of Defect DCSG00230346))
-Storcli command description shows none for Download firmware failure.(DCSG00221431 (Port Of Defect DCSG00223281))
-Instance Validation Failed for /call/show_all.json and controller-detailed-properties-schema.json.(DCSG00132488 (Port Of Defect DCSG00137828))
-NoVDs is displayed in dall show output..(DCSG00074628 (Port Of Defect DCSG00074763))
-"reset errorcounters" command mentions options under conventions.(DCSG00074288 (Port Of Defect DCSG00074764))
-PH16 PA - StorCLI - Compare fwprodid help page needs to be updated.(DCSG00167732 (Port Of Defect DCSG00215133))
-Display basic secure boot details for Sea IT controller.(DCSG00074184 (Port Of Defect DCSG00074218))
-No consistency in the description of Force option.(DCSG00074283 (Port Of Defect DCSG00074765))
-Storcli /c0/eall show status extended command fails to generate any output for ARM server backpla.(DCSG00146359 (Port Of Defect DCSG00150479))
-Debug log configuration file for perccli is taking storcliconf.ini.(DCSG00074691 (Port Of Defect DCSG00074757))
-Compare fwprodid command fails for 9500-16i.(DCSG00092943 (Port Of Defect DCSG00115266))
-Handling of controller properties related to drive FW download.(DCSG00138192 (Port Of Defect DCSG00139266))
-In command storcli /cx/ex/sx show DPM type=Ext , Sectors Read (Written) is not displayed correctly.(DCSG00083167 (Port Of Defect DCSG00103210))
-Ph16 PA: Storcli crash observed while running show all with NVMe drives connected.(DCSG00150686 (Port Of Defect DCSG00167881))
-Description for "profileid=" is missing in help and detailed help.(DCSG00152251 (Port Of Defect DCSG00152935))
-EKMS Boot Agent Status is not updating properly..(DCSG00049004 (Port Of Defect DCSG00050289))
-MR 7.15: Storcli: Force option is mentioned as "For".(DCSG00223195 (Port Of Defect DCSG00225259))
-Storcli displays 255 max spin-up drive count in help description instead of 240.(DCSG00098081 (Port Of Defect DCSG00108741))
-"Compare factorysettings" command displays incorrect output for wrong input file.(DCSG00075762 (Port Of Defect DCSG00075888))
-Storcli64 /cx show spinupdrivecount help file description needs update.(DCSG00150052 (Port Of Defect DCSG00150459)
-Segmentation with controller show summary command when controller is in unsupported state.(DCSG00215109 (Port Of Defect DCSG00215118))
-StorCLI show autoconfig does not display all properties it can set.(DCSG00071834 (Port Of Defect DCSG00080859))
-Storcli returns wrong Operating system in Windows..(DCSG00037088 (Port Of Defect DCSG00037336))
-No description for "set autoconfig=R0 immediate" command..(DCSG00129610 (Port Of Defect DCSG00129762))
-Displaying connected portnumber as per API supportMoreThan16Phys.(DCSG00104331 (Port Of Defect DCSG00108740))
-Compare Factory command execution fails in storclif.(DCSG00074182 (Port Of Defect DCSG00074207))

EnhancementRequests:
-HPE : Windows and Linux StorCLI signing.(DCSG00053511)
-Implement changes to secureSign signing tool and infrastructure to support mixed list of PublicKeys that are from SCGCQ and DCSG..(DCSG00105430)
-API change to support ISE completion status.(DCSG00065881)
-MR API: Change event class for SPDM events.(DCSG00134416)
-API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI.(DCSG00222915)
-Perccli: Need a mechanism to get supported device protocols for each controller form factor.(DCSG00117742)
-support for sanitize command.(DCSG00108999)
-Shenandoah: Support for the New Energy Pack states.(DCSG00043240)
-Preboot Trace Buffer [PTB] for Ventura/Aero - MR API.(DCSG00060713)
-Remove Help Text for lanespeed commands.(DCSG00099939)
-Shenandoah: Change the CLI installation Directory name from Megaraid to hpe.(DCSG00053988)
-Porting storcli source from V8 Clearcase to CC9 GCP database.(DCSG00013486)
-Creating VD with 0 MB or GB should not be allowed to succeed --ve case boundary value scenario.(DCSG00048859)
-MR API: NVME Drive Init Error Report and Repair for Aero/Ventura.(DCSG00071534)
-DCSG00129388
-Support to display drive connector name information for SAS3.5 IT Controllers.(DCSG00120994)
-Add segment area into pci information of Megaraid controller in storcli.(DCSG00032694)
-Populate secureboot properties "KeyUpdatePending" and "Remaining Secure Boot Key slots" in StorCLI.(DCSG00101684)
-Remove (hide) PCIe Link form in HII and from CLI for Perc11.(DCSG00077856)
-Define MR_SAS_PHY_CONNECTION.currentSpeed when no devices are connected.(DCSG00071066)
-Signing Linux executables via GPG method in HSM.(DCSG00077215)
-Shenandoah: Creating VD with 0 MB or GB should not be allowed to succeed - Part 2.(DCSG00053587)
-Shenandoah: SSD Wear Gauage.(DCSG00046064)
-MR API changes - Support new DCMD for Platform Security SPDM.(DCSG00068355)
-Add /px linkspeed back to help text.(DCSG00126913)
-HSW Applications to not send close DCMD as the first command to perform Firmware update.(DCSG00055146)
-Update/remove Snapdump save count field in show snapdump command based on FW support.(DCSG00038800)
-Include new field cannotSetMode in MR_AUTO_CFG_PARAMETER structure..(DCSG00072780)
-API changes to expose MR_AUTO_CFG_PARAMETER for NONE mode.(DCSG00151058)
-Add new security events.(DCSG00167313)
-Request for DPMstat support in MegaRAID SAS 3.5 controllers in storcli.(DCSG00032273)
-MR API: update field in event structure..(DCSG00093331)
-Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API.(DCSG00226286)
-SMART Polling Improvement- API Changes.(DCSG00214352)
-References to MR_ENCL_LIST and MR_ENCL_LIST_EXT should be based on the support bit.(DCSG00037323)
-Shenandoah: Type 2 Back plane Support for StorCLI.(DCSG00054795)
-StorCLI: Implementing span depth logic and pd per array count for RAID 10.(DCSG00049781)
-Updating BST scripts to support auto BST through VBAS in clear case version 9.(DCSG00050763)
-FW SAS MEGA API:Change MR_EVT_CTRL_FLASH_DISALLOWED_SB_KEY_CHANGE_PENDING event.(DCSG00086780)
-Revert the CLI Help Text for backwards compatibility to include Dimmer Switch 3.(DCSG00068659)
-Shenandoah: Reverting back the changes made for Span setting for RAID 1 & 10.(DCSG00073393)
-New MFI Stat for the updated recon behavior.(DCSG00229416)
-Shenandoah: Remove Span setting for RAID 1 & 10.(DCSG00043198)
-Restore Factory Default doesn't prompt user to reboot the system after being performed.(DCSG00122000)
-MR API changes - Support new Provisional bit in CTRL INFO and new MFI status for Platform Security.(DCSG00106380)
-Add support for signing MegaRAID Legacy BIOS CU Images (CTLR) images.(DCSG00143847)
-Phase 14 : StorCLI should provide power cycle message post erase all command is executed.(DCSG00039542)
-Enhancement of Enclosure MultiPath algorithm in storcli.(DCSG00075191 (Port Of EnhancementRequest DCSG00079538))
-Support to generate storcli static library.(DCSG00075265 (Port Of EnhancementRequest DCSG00075687)
-Updating toolchain for VMware7.0 GA.(DCSG00134764 (Port Of EnhancementRequest DCSG00136269))



007.1212.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------  
MR 7.12

Defects:
StorCLI should refer to MR_PD_INFO.properties.ISECapable to display "Cryptographic Erase Capable" field - Revert of SCG(DCSG00014660)
Making the Predictivefaliure  check OEM specific in controller health algorithm(DCSG00014971)
HBA345_Dev_UT: Enclosure position value in perccli is same for both front and rear BP's(DCSG00033180
Cisco - CSCVr89052 - PATH_1 and PATH_BOTH assigned drives not getting displayed under storcli in WF DDROCK setup(DCSG00050891)
StorCLI Point release RO DCSG00079546 - Windows binaries are missing from the RO(DCSG00081022)
 StorCLI 7.10 point release  - /cx erase help not listing all supported commands(DCSG00081294)
StorCLI 7.10 point release - Update license files to RO DCSG00079546(DCSG00081298)
Removal of unsupported phy commands on IT3 controller(DCSG00025416)
Phase 12 - Oct Huawei DET - New PD FW Not Updated After Flashing PD FW (NVMe)(DCSG00015875)
MR_6.14_Huawei: OnDemand Snapdump in Windows gives failure message "RTTdump Feature not supported"(DCSG00020717)
help is not proper for show events and set copyback commands(DCSG00005503)
MR 7.12: Storcli: Instance Validation Failed for "/call show all" and controller-detailed-properties-schema(DCSG00006331)
MR 7.12: Storcli: Instance Validation Failed for "/call/pall show all" and controller-phyerrorcounters-schema(DCSG00006853)
Orion PA9 : Convention comes in same line while performing help for /c0/e0/s0 download.(DCSG00008084)
MR_7.12_Storcli: Xenserver8: "Core dumped" while executing "/call/eall show all" and "/call/eall/sall show all"(DCSG00009400)
Aero DBU PA7 : Init is in progress error message is thrown by Storcli for start migrate command when VD erase is in pro(DCSG00012344)
Orion PA9 : Storcli version mismatch as compared in storcli -v and storcli properties(DCSG00014485)
Orion PA9 : Storcli crashes while performing storcli /c0 show(DCSG00014486)
Storcli show all cmd displaying "AVAGO" in scheduled tasks info(DCSG00014580)
Aero DBU PA7 : Storcli displays multiple error messages when user enters incorrect device ID during migrate operation.(DCSG00014644)
Fixing Coverity defects - resource leaks and null referencing(DCSG00015721)
Correcting the detailed help syntax(DCSG00016268)
MR7.12 StorCLI: Ouptput message Description wrong for StorCLI VD policy change from WT -WB(DCSG00016372)
StorCLI:  Fixing coverity defects and adding debug statement(DCSG00019683)
perccli windows binary property page has storcli references(DCSG00019800)
Aero DBU Alpha : Storcli displays incorrect error message for "add vd each r0" command when SED drive is connected in t(DCSG00019816)
Application Exit code is always success for UEFI StorCLI(DCSG00020670)
MR 7.12 LSA "instant secure erase" is not found in storcli as cli use secureerase(DCSG00022096)
Help content for Drive Init is not showing it as Clear operation(DCSG00022893)
MR7.12_Storcli: On drive rebuild, there is a mismatch between the pd rebuild state and respective legend(DCSG00022942)
MR 7.12: Storcli: Instance Validation Failed for "/call start Diag Duration=40" and controller-diag-schema(DCSG00023543)
MR 7.12: Storcli: Instance Validation Failed for "/call show linkconfig " and controller-linkconfig-schema(DCSG00023545)
Aero Alpha : Storcli throw Segmentation Fault in Driver load error handing path -(DCSG00024554)
MR 7.12_Storcli: On ARM server the latest storcli Vendor,Licenses,URL and distribution shows as "AVAGO Technologies"(DCSG00025885)
Aero DBU Alpha - Scheduling is displayed as Schedulling under "/cx set pr ? " command description(DCSG00027203)
Add warning/recommendation messages for changing lane speeds(DCSG00027869)
Orion MR : Description for storcli output is not proper after collecting the snapdump with id=all(DCSG00031711)
Aero Alpha: Storcli stops functioning during run of attached script(DCSG00034379)
Storcli returns wrong Operating system in Windows.(DCSG00037088)
MR 7.12_Storcli: The latest storcli vmware build reference URL shows "http://www.lsi.com"(DCSG00039104)
MR 7.12_Storcli: The latest storcli vmware build 007.1209.0000.0000 shows older package version(DCSG00039112)
PERC 11:EKMS:PKG 2973: EKMS Boot Agent Status is not updating properly.(DCSG00049004)
PH13 StorCLI PA - Update help section about 'nolog' option(DCSG00002975)
PH13 PA - StorCLI - Incorrect message for /call/pall show all command(DCSG00003003)
StorCLI_7.12_Ph13:Phyreset Fails on IT controllers(DCSG00005488)
PH13 PA - StorCLI - NVMe drive linkspeed not seen with /cx/pall show(DCSG00009522)
With IT controller for set or reset with invalid phy is not showing error(DCSG00010226)
Aero_storecli:Using latest storecli Firmware product id parameter value fail to display.(DCSG00011446)
MR_7.12: Storcli: Segmentation Fault for "storcli64 page"(DCSG00012563)
Storcli ph13: Fixing array size for function DEBUG_LOG(DCSG00014665)
Aero Orion IT:- Mismatched phy info listed for 440-16e/440-16i(DCSG00023320)
Enclosure position value in storcli is same for both front and rear BP's(DCSG00031302)
Misleading error message when create unmap VD with storcli64.exe /c0 add vd each r0 unmap using unmap and non-unmap PDs(SCGCQ02059720)
StorCLI: Debug prints enabled in latest Phase 12 PA storCLI.efi image(SCGCQ02097317)
Json Schema for the command "storcli /cx/ex show phyerrorcounters" needs to be updated(SCGCQ02101372)
MR 7.11: Storcli: Instance Validation Failed for "/call show all" and system-schema.json(SCGCQ02112192)
DBU Aero PA4 : Cosmetic error is seen in command description for Show SSDThermalPollInterval ?(SCGCQ02124673)
Aero A0 PA4: "Storcli /c# set jbod=on" shows success but does nothing(SCGCQ02117219)
Aero (DBU PA4):Storcli: Junk character in PD start locate command description.(SCGCQ02125654)
Phyreset Fails on IT controllers and update help(SCGCQ02169242)
Drive mode-e fw download with activatenow is not working(SCGCQ02142068)
MR 7.11: Storcli: Instance Validation Failed for "/call/eall show status extended" and enclosure-status-extended-schema.json(SCGCQ02150924)
MR7.11_Storcli: Incorrect error description while creating r1 with single drive(SCGCQ02165933)
Phase 12 - Oct Huawei DET - "./storcli64 /c0/pall show" Command Fails With "Null pointer exception"(SCGCQ02175414)
Phase 16 (IR) - Oct Huawei DET - Unsupported Drive State is Displayed for "./storcli /c0 show" Command(SCGCQ02170389)
MR 7.11 - Oct Huawei DET - Nomenclature Issue for "rbld=Rebuild" In Storcli Show Help Menu for SAS3516(SCGCQ02170197)
Usage of 64 bit address instead of 32bit address while sending commands to FW in uEFI driver less environment(SCGCQ02174934)
MR_7.10_Storcli: Storcli displays incorrect error message for unmap VD creation with regular HDD drives.(SCGCQ02019751)
PH12 PA - StorCLI crashes when call/pall show executed with SAS3 & Ventura boards(SCGCQ02103217)
PH12 PA - StorCLI - Debug StorCLI binary is placed in both places of EFI dir RO SCGCQ02085693(SCGCQ02091140)
PH12 PA - Update readme file in VMwareOP64 folder in accordance with PR SCGCQ01923533(SCGCQ02108550)
MR 7.11: Storcli.efi: In ARM server UEFI shell, storcli.efi hangs forever when storcliconf.ini is present(SCGCQ02115036)
Aero (DBU PA4):Storcli:  VD legend is missing in "/call/vall show expansion" command.(SCGCQ02124508)
Aero DBU PA4 : storclif /cx show configautobalance  ? help output shows the name as "show NCQ"(SCGCQ02124632)
Configuring multiple lane speed is working only for fisrt ID, Rest were ignored(SCGCQ02136333)
Aero (DBU PA5):Storcli: Storcli: "/c0 set patrolread ?" lists detailed help and snapdump rttdump is mentioned as optional.(SCGCQ02140873)
MR 7.11: Storcli: Instance Validation Failed for "/call/eall show status" and enclosure-status-schema.json(SCGCQ02150921)
Aero (DBU PA5):Storcli: Force is not mentioned as key word in "/cx/vx del" error message.(SCGCQ02142017)
MR7.11_Storcli: On drive rebuild, there is a mismatch between the pd rebuild state and respective legend(SCGCQ02165944)
Aero (DBU PA5):Storcli: "Ctrl" legend not mentioned.(SCGCQ02146822)
MR7.11_Storcli: storcli set securitykey detailed help does not show description for all the options(SCGCQ02096732)
MR7.11_Storcli: storcli show output shows UBUnsp as UBad Unsupported where as UGUnsp just Unsupported(SCGCQ02096722)
Aero IT - PA3 - StorCLI crashes for 'storcli J command(SCGCQ02117749)
Lenovo Orion IT:- Command to flash UEFI on Aero/sea HBA from storcli/scrutiny fails(SCGCQ02137751)
Flashing of Completeflash fails on Sea IT controller(SCGCQ02139780)
StorCLI: Fixing coverity defects(SCGCQ02123769)
MR 7.11: Storcli: Instance Validation Failed for /call/show_smartpollinterval.json and controller-smartpollinterval-schema.js(SCGCQ02135516)
DBU PA5 Aero : Background operations keep on progressing after hitting /c0 shutdown from storcli(SCGCQ02132024)
Aero (DBU PA5):Storcli: No "Rbld" legend during rebuild.M(SCGCQ02146819)
complete Lane WWID is not displayed(SCGCQ02145716)
Convention comes in same line while performing help for /c0/e0/s0 download.(SCGCQ02176681)
Adding missing syntax for the command deviceorderbyfirmware(SCGCQ02121705)
MR 7.11: Storcli: Instance Validation Failed for "/call/vall show unmap" and vd-unmap-schema.json.(SCGCQ02113316)
Aero (DBU PA5):Storcli: "completeflash" is listed in Windows help file.(SCGCQ02141931)
Aero (DBU PA5):Storcli: Force option not mentioned in "/cx/dx add mirror" and "/cx/vx start init" command.(SCGCQ02140878)
Force option is needed only for Parallel Drive microcode update, but it allows to take for normal also(SCGCQ02177086)
StorCLI Copyright Notice Needs to be updated(SCGCQ02174040)
Wrong error message when create unmap VD with unmap disable on controller(SCGCQ02064118)
Aero DBU PA4 : storclif /cx delete colinfo  ? shows syntax error(SCGCQ02124492)
MR 7.11: Storcli: Instance Validation Failed for "/call show" and controller-properties-schema.json.(SCGCQ02108770)
PH12 PA - StorCLI version not getting printed for show file command(SCGCQ02105185)
Aero DBU PA4 : Command name shown in help output differs for storclif.efi /cx show limitmaxrateSATA ?(SCGCQ02124667)
Aero DBU PA4 : Redundant information is displayed for set driveactivityled command in storclif.(SCGCQ02124675)
Aero (DBU PA4):Storcli: Wrong reference of "page=[X]" as part of syntax error message.(SCGCQ02124252)
Aero DBU PA4 : storclif.efi /cx show deviceorderbyfirmware ? throws syntax error.(SCGCQ02124528)
MR 7.11: Storcli: Instance Validation Failed for /call/show_consistencycheck.json and controller-cc-schema.json(SCGCQ02135510)
Phase12-Storcli- In Windows storcli64.exe /c0 show htbparams is showing random values for SAS3 controller(SCGCQ02125598)
Aero (DBU PA5):Storcli: No description of patrolread "OFF" and optional is mentioned as {}.(SCGCQ02140859)
PH12 BETA - /cx erase help not listing all commands(SCGCQ02146466)
Aero (DBU PA5):Storcli: No consistency in the usage of "|" in the command such as "on|off".(SCGCQ02142022)
Phase 12 - Oct Huawei DET - Delay Option In PD Download Operation is Not Honored(SCGCQ02176690)
With IT controller for set or reset with invalid phy is not showing error(SCGCQ02181823)
Updating phy link reset logic for IT cards with respect to storelib changes(SCGCQ02184862)
Drives connected to active backplanes not showing the phy info in connector name(SCGCQ02112424)
PH12 PA - StorCLI - 9310-8i IR FW download fails(SCGCQ02121783)
MR 7.11: Storcli.efi: On ARM server, incomplete configuration data received error is observed for any storcli.efi command(SCGCQ02114898)
Aero PA6 - storcli snapdump id=x errors without optional file parameter(SCGCQ02161748)
PH11 - StorCLI - Incorrect message for /call/pall show all command(SCGCQ02169536)
cli does not allow  to do crypto erase on SATA SSD.(SCGCQ02147075)
MR7.11_Storcli: Storcli stop erase needs an help file update(SCGCQ02168895)
Phase 12 - Oct Huawei DET - Incorrect Help Menu For "show phyerrorcounters"(SCGCQ02180495)
Phase 12 - Oct Huawei DET - New PD FW Not Updated After Flashing PD FW (NVMe)(SCGCQ02191421)
Aero PA4 DBU : Storclif doesn't show details for VF/PF in help file for vfmap command .(SCGCQ02123789)
Aero (DBU PA4):Storcli: Typo in /c0 add vd detailed help.(SCGCQ02119091)
Aero (DBU PA4):Storcli: /c0 compare lists /c0/px compare command.(SCGCQ02124246)
StorCLI: Fixing coverity issue in libmod(SCGCQ02123790)
SWR:Storcli: "Show" and "show all" output Description is shown as "No Enclosures found"(SCGCQ02146814)
MR 7.11 storcli -help missing the verbose option(SCGCQ02158600)
Phase 12 - Oct Huawei DET - PD FW Download is failing for Mode f(SCGCQ02168197)
PH12 PA - StorCLI - Incorrect string displayed with show command in FreeBSD 11.2(SCGCQ02094529)
PH12 PA - StorCLI /cx/pall show fails on 9400-8e board(SCGCQ02119004)
MR 7.11: Storcli: Instance Validation Failed for "/call/v5 set bootdrive=off" andcontroller-bootdrive-schema.json.(SCGCQ02115786)
StorCLI: Fixing coverity defects for second run(SCGCQ02125523)
MR 7.11: Storcli: Instance Validation Failed for /call/show_all.json and controller-detailed-properties-schema.json(SCGCQ02135526)
Aero (DBU PA5):Storcli: /c0 set ? lists bbu,mx,px and lnx commands.(SCGCQ02136689)
Aero DBU PA4 : Storclif should not display vendor name in storclif.efi  /cx/ex download help command(SCGCQ02123765)
Aero (DBU PA5):Storcli: Improper spacing for the linkspeed description and "YY" parameter leads to confusion.(SCGCQ02139910)
MR 7.11: Storcli: Instance Validation Failed for /call/show.json and controller-properties-schema.json(SCGCQ02135420)
MR 6.14 - Oct Huawei DET - "Rbld=Rebuild" is Not Available In Storcli Show Help Menu for SAS3108(SCGCQ02170181)
MR 7.11: Storcli: Instance Validation Failed for "/call/cv show all" and cache-vault-detailed-schema.json(SCGCQ02150651)
Aero (DBU PA5):Storcli: Help notes needs an update.(SCGCQ02146823)
Phase 12 - Oct Huawei DET - Incorrect Status for PD FW Download (Ventura IT)(SCGCQ02173203)
Phase 12 - Oct Huawei DET - Incorrect Phy Details Displayed for Ventura IT Controller(SCGCQ02174296)
	
Enchancement:
To bring MR 7.10 storcli change to CC9 GCP database(DCSG00013486)
Support to generate storcli static library(DCSG00075265)
Bring MR 7.11 storcli change to CC9 GCP database(DCSG00014492)
Updating the Makefile and projects as per new CC/CQ changes(DCSG00003002)
Updating the Json Schema files with respect to the latest code(DCSG00007394)
Controller commands Json Schema files update as per the latest code(DCSG00007435)
Schema validation : Schema update for VD/DG/Foreign related commands(DCSG00007453)
Add UEFI Shell StorCLI support for 64-bit Ventura Gen MR Legacy Boot solutions (solutions without UEFI driver)(DCSG00008200)
Changing the CBB download image type as per new MR API(DCSG00010253)
Migrating StorCLI's 64 bit VMware toolchain to 6.8.7-13394445(DCSG00014503)
PERC 11: Provide ability to expose SEP to host and disable PERC SES management in PercCLI / HII(DCSG00015020)
Supporting build and BST process through VBAS in Clear Case version 9(DCSG00024818)
Windows and Linux StorCLI HSM based signing support(DCSG00031618)
StorCLI PH13: Adding interface for lane display and configuration command for IT controllers.(DCSG00007909)
Atlas Support on Aero-IT(DCSG00008038)
Concern for security key passed in from storcli to be read in process data(SCGCQ02066380)
Support FMP Images in UEFI Version of PERCCli(SCGCQ02078649)
Add segment area into pci information of Megaraid controller in Storlib and storcli(SCGCQ02201178)
Create DVT / PVT PnP IDs for Cisco Pismo Beach card(SCGCQ02108965)
Return pended IOCTLS that was not completed after some numbers of OCRs had been initiated.(SCGCQ02066395)
Enable SnapDump for iMR(SCGCQ02208421)
HDET: Support in storCLI support PD firmware download for 3008IR/3008IT controllers(SCGCQ02160016)
multi VSES implementation(SCGCQ02066438)
Return pended IOCTLS that was not completed after some numbers of OCRs had been initiated.(SCGCQ02066399)
Add displaying list of enclosures in controller show and show all command(SCGCQ02124566)
LibMod changes : MR: 64 Bit  Utilities/Application to Support VMWARE ESXi 6.7+(SCGCQ02085102)
SAS 3_5 Ventura family UEFI NVMe drive serial number issue(SCGCQ02074657)
Unmap error message changes as per new description in MR API(SCGCQ02115017)
MR: 64 Bit  Utilities/Application to Support VMWARE ESXi 6.7+(SCGCQ02066386)
Lenovo Whitley/Orion - Addendum 7 - Lenovo request to support StorCLI & LSA for Valvano 28i (MR+Cub) and Custom Form Factor(SCGCQ02082612)


007.1022.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------

Defects :
 - PERCcli Help text is missing description for "Lane Information"(SCGCQ02150899) 
 - Add NVMe width comments to mr.h(SCGCQ02146846) 
 - Fix API changes done for NVMe readiness(SCGCQ02142981) 
 - CLI returns "success" when attempting to set DS3 or DS4 to enabled(SCGCQ02116380) 
 - CLI returns "success" when attempting to change the H840 controler to eHBA personality.(SCGCQ02114332) 
 - CLI returns wrong error code upon failure(SCGCQ02084966) 
 - HPE shenandoah: storcli crashes during show command when DGs present(SCGCQ02065695) 
 - "Run time to empty" field showing as "Battery is not being charged" when the battery is being charged.(SCGCQ02045324) 
 - ROP version not displayed with latest ROP version SCGCQ02035462(SCGCQ02041094) 
 - FW flash fails to load the latest image after upgrade downgrade with resetnow option(SCGCQ02035152) 
 - retentiontest command is successfully triggering BBU test on Shenandoah controller(SCGCQ02021398) 
 - Storclio (007.0911.0000.0000) detailed help file doesn't have " locale " option for flashing FW in Dual/Active & Backup mode.(SCGCQ02012025) 
 - hot spare reference in Add Spare command output(SCGCQ01897463) 
 - Shenandoah:Strocli show all output return failure but generates output(SCGCQ01929191) 
 - Junk message "STR_JBOD_OBJ" is displayed in the output of storcli /c0 show JBOD command.(SCGCQ01932770) 
 - Shenandoah_StorCLI: No legend presend for VD Delete Failure(SCGCQ01936811) 
 - Shenandoah_StorCLI:Setting Unmap=OFF gives success for a LD when unmap is not supported and not enabled on that LD(SCGCQ01940291) 
 - Set WrCache= WB ,says success even though VD is in WT.Proper warning message should be given to the user(SCGCQ01940296) 
 - Legend missing for LD BGI resume/pause commands(SCGCQ01940347) 
 - System hangs while creating VD in EFI shell.(SCGCQ01945551) 
 - Shenandoah_StorCLI: Storcli crashes on checking LD preserved cache info(SCGCQ01955069) 
 - CLI is showing the incorrect OS version(SCGCQ01956276) 
 - Unified StorCLI : Add extra space to CBB header(SCGCQ01956678) 
 - PH10 Alpha - StorCLI throws "0 Failed 32782 Failed to get PD Info" when /c0 show executed in EFI(SCGCQ01960322) 
 - JBOD list is not showing in order when using /cx show(SCGCQ01961527) 
 - supported personalities has blank value(SCGCQ01965370) 
 - storcli faults for enclosure show command(SCGCQ01985815) 
 - MR7.10_PA1: Storcli binaries for RHEL/SLES OS is not present for ARM(SCGCQ02006374) 
 - NVMe drive displays incorrect information with IT card(SCGCQ02009852) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set personality" JSON output.(SCGCQ02016762) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for snapdump commands.(SCGCQ02018073) 
 - MR_7.10_Storcli: No schema file for controller sesmultipathcfg commands.(SCGCQ02018134) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for drive jbod commands.(SCGCQ02018135) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for "/cx get vpd" commands.(SCGCQ02018140) 
 - MR_7.10_Storcli: Instance Validation Failed between "virtual-drive-detailed-schema.json" and "/call/vall show all "(SCGCQ02018333) 
 - MR_7.10_Storcli: bbu-show-modes-schema.json file is not in JSON format.(SCGCQ02019740) 
 - Instance Validation Failed between " controller-lane-show-schema.json" and "/call/lnall show"(SCGCQ02019746) 
 - Pending Image details are not populated after FW upgrade and downgrade.(SCGCQ02024065) 
 - Instance Validation Failed between "controller-detailed-properties-schema.json" and "/call show all "(SCGCQ02032911) 
 - MR_7.10_Storcli: Add VD command output is not in JSON format.(SCGCQ02034493) 
 - Instance Validation Failed between "vd-unmap-schema.json" and "/call/vall show unmap"(SCGCQ02035370) 
 - remove the maxconcurrentpd check from storcli and report fw returned failure(SCGCQ02053910) 
 - Storcli: "resume migrate" command does not show syntax error.(SCGCQ02061340) 
 - Instance Validation Failed between "controller-detailed-properties-schema.json" and "show_all"(SCGCQ02062957) 
 - Show Snapdump help command lists delete snapdump details as well.(SCGCQ02064836) 
 - Storcli: "show config" command shown as Un-supported.(SCGCQ02064839) 
 - PH11 Alpha - StorCLI 'show file' command throws segmentation fault for complete flash image in FreeBSD(SCGCQ02065691) 
 - Storcli: No schema files for htbparams commands.(SCGCQ02065698) 
 - "Delete snapdump" command shows same description "Snapdump clear" for success and failure case.(SCGCQ02065734) 
 - Incorrect error message displayed while creating R10 VD when no free space available.(SCGCQ02067575) 
 - Schema file updates for controller show all output change for defect SCGCQ02048150(SCGCQ02069817) 
 - Typo in storcli /c0 set linkspeed help(SCGCQ02070951) 
 - Aero (DBU PA2): Storcli: No syntax error displayed for "storcli mronly" command.(SCGCQ02072746) 
 - Wide port info is not displayed under connector name for Backplane attached drives.(SCGCQ02076923) 
 - Empty data is listed when we query for show linkconfig(SCGCQ02076931) 
 - htbparams help output needs update.(SCGCQ02077156) 
 - show/set lane speed shows success when we are in SAS profile(SCGCQ02078437) 
 - Libmods: show.set lane speed shows success with wrong data when we are in SAS profile(SCGCQ02078513) 
 - Recon command (./storcli /cx set recon) is throwing syntax error.(SCGCQ02081415) 
 - storcli /c0/ex/s23,24 show patrol read doesnt not show error for slot 24 (Invalid Slot)(SCGCQ02082142) 
 - Aero (DBU PA2): Storcli show detailed help does not list "show all " command.(SCGCQ02082303) 
 - Aero (DBU PA2): Storcli: Get rttdump detailed help shows syntax error.(SCGCQ02082460) 
 - Storcli: Incorrect message while executing "storcli64.exe /c0/v0 del discardcache"(SCGCQ02083828) 
 - Failure status for /call/sall and /call/eall/sall command.(SCGCQ02084549) 
 - Storcli: Error in /c0/f0 command output.(SCGCQ02089892) 
 - StorCLI listing PD Slot Status as "Incorrect Status Value" for configured PD's(SCGCQ02090770) 
 - Storcli doesn't exit with controller status message after doing OFU.(SCGCQ02091548) 
 - Libmod changes for SCGCQ02090770	(SCGCQ02096774) 
 - Aero (DBU PA3): Storcli: FW hits Megamon while executing storcli in EFI shell when EFI Driver is unloaded.(SCGCQ02097647) 
 - StorCLI crashes for 'storcli J command(SCGCQ02117749) 
 - Storcli: VD legend is missing in "/call/vall show expansion" command.(SCGCQ02124508) 
 - Controller Health Status not consisten across applications(SCGCQ02182243) 
 - Perccli does not enable Power Save mode for UG & HS type 1 & type 2.	(SCGCQ02125408) 
 - StorCLI: Delete config failure message need correction(SCGCQ02086726) 
 - StorCLI:VD reference in Delete preserved cahce command output -Branding(SCGCQ02083992) 
 - VD reference in set JBOD command output message(SCGCQ02078507) 
 - storclif.exe /c0/ex/sx show poh should show proper message during command execution.(SCGCQ02075242) 
 - STORCLI: Show command output having wrong legend for Slt for oem Hercules(SCGCQ02067616) 
 - Grammatical error in Perccli message(SCGCQ02065513) 
 - BSOD observed when VD/JBOD Creation/Del and snapdump Cycles are initiated.(SCGCQ02045967) 
 - VD legend missing in the legend for Foreign config show all output(SCGCQ02016798) 
 - Hercules:Shenandoah:Transformation is coming as Reconstruction , while migrating the Raid 1 to Raid 5 .(SCGCQ01897468) 
 - Mis-spelled words in StorCli's Help(SCGCQ01898853) 
 - Hot spare reference in storcli.exe /cx/ex/sx show all command output(SCGCQ01905019) 
 - Reference to VD in storcli.exe /c1/jbodall delete command output(SCGCQ01905077) 
 - Fixing coverity issues Removing dead code and Out of bound access(SCGCQ01924504) 
 - Shenandoah_StorCLI: HotSpare reference in Add VD Command output(SCGCQ01936887) 
 - storcli /c0 show events output not listing the Event ID's(SCGCQ01940290) 
 - Shenandoah_StorCLI:Hot spare reference in storcli64 /cx show/set restorehotspare command outputs(SCGCQ01940437) 
 - Shenandoah_StorcLI:Drive Group reference in Add dedicated spared drive command in CLI(SCGCQ01955167) 
 - Intel NVMe drive "Model Number" displayed incorrect under Device Attributes(SCGCQ01957949) 
 - Aero: Segmentation Fault in storcli /c0 show all(SCGCQ01996444) 
 - Storcli throws an 'Incomplete foreign configuration' error when there is no enclosure connected(SCGCQ02006450) 
 - storcli gives error when the lane configuration is set as X8	(SCGCQ02007152) 
 - MR_7.10_Storcli: No schema file for controller unmap commands(SCGCQ02016749) 
 - MR_7.10_Storcli: Instance Validation Failed "controller-restorehotspareoninsertion-schema" and "set restorehotspare"(SCGCQ02016765) 
 - MR_7.10_Storcli: Instance Validation Failed "controller-properties-schema" and "/c0 show"(SCGCQ02016768) 
 - MR_7.10_Storcli: controller-detailed-properties-schema.json or "/call show all " output not in JSON format(SCGCQ02016771) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-autoconfig-schema.json" and "show autoconfig" JSON output.(SCGCQ02018227) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" JSON output.(SCGCQ02018277) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON output.(SCGCQ02018305) 
 - MR_7.10_Storcli: Instance Validation Failed between "system-schema.json" and "./storcli show" and "show all" JSON output.(SCGCQ02018313) 
 - MR_7.10_Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/eall/sall show all"(SCGCQ02018327) 
 - MR_7.10_Storcli: Instance Validation Failed between "cache-vault-detailed-schema.json" and "/call/cv show all "(SCGCQ02019729) 
 - Storcli displays drive state as UBad instead of UBad (unsupported)(SCGCQ02031615) 
 - Instance Validation Failed between "drive-group-hidden-schema" and "/c1/dall set hidden" & "set security"(SCGCQ02040779) 
 - Fixing coverity issues Fixing resource leaks(SCGCQ02043601) 
 - Storcli help file should show the expand size format.(SCGCQ02047109) 
 - Updating the storcli schema mapping document	(SCGCQ02050586) 
 - PH11 Alpha - StorCLI - Parse error observed for command 'StorCLI J' while validating Jason(SCGCQ02053030) 
 - JSON-SCHEMA : IT-Controller Json-schema validation erros in MR_SAS_Unified_StorCLI_7.10(SCGCQ02053914) 
 - Aero: Storcli : Storcli crashed when Firmware upgrade tried on Sea controller(SCGCQ02060276) 
 - Aero (DBU PA2): Storcli: JSON readme file does not have complete VD and PD support list.(SCGCQ02061328) 
 - Instance Validation Failed bw "enclosure-drive-detailed-schema.json" & "/call/eall/sall show all"(SCGCQ02062958) 
 - PH11 Alpha - StorCLI - Compare linkspeed command failed for 6Gbps link(SCGCQ02063932) 
 - Invalid aero controllers are not displayed with apt message in driver less mode(SCGCQ02065581) 
 - Storcli connector display not matching with Aero board 9560-16i.(SCGCQ02072448) 
 - Aero (DBU PA2): Storcli: /cx/mx command does not mention about "Auto" settings.(SCGCQ02082208) 
 - Storcli: Force is mentioned as optional in snapdump delete command.	(SCGCQ02083822) 
 - Help of /cx/px compare command needs update and /cx/px reset ? shows syntax error.(SCGCQ02084752) 
 - No proper legends in /fall output.(SCGCQ02100491) 
 - Aero (DBU PA3): Storcli: Incorrect schema mapping for "/cx set autoconfig " command.(SCGCQ02101558) 
 - Storcli: OCR helps needs update.(SCGCQ02113241) 
 - Storcli: No proper description of set and show sesmultipathcfg.(SCGCQ02113358) 
 - StorCLI: File sync issue with rel and dev stream for MR 7.10	(SCGCQ02116806) 
 - Storcli script stops with error "can't fork: Cannot allocate memory"	(SCGCQ02184427) 
 - IT- CLI treats EID and Partner Device ID as two different enclosure during pd info command and fails.(SCGCQ02185442) 
 - "/eall show" will not show enclosure details if it is in multitpath & no drives connected.(SCGCQ02186022) 
 - Legacy messages present with create and rekey of securitykey on controller(SCGCQ01581843) 
 - Shenandoah_StorCLI:VD reference in CLI outout for Firmware update command failure case(SCGCQ02083991) 
 - StorCLI: VD listing for c0 show and vall show is toggled	(SCGCQ02078936) 
 - output information for link configuration is displayed incorrectly(SCGCQ02073046) 
 - Drive Groups is shown instead of arrays in show all command(SCGCQ02048660) 
 - Help is not updated for get snapdump without ID option.(SCGCQ02046991) 
 - StorcliO show oob command fails for Invader based cards(SCGCQ02040783) 
 - Adding debug logs to Mfi files(SCGCQ01891583) 
 - MR7.8_Storcli: Storcli fails to install on ARM server with Missing Maintainer message(SCGCQ01919830) 
 - StorCLI show SAS address for NVMe drives	(SCGCQ01921258) 
 - Unified StorCLI 7.9 : Fixing coverity issues - Dead code,resource leaks,and memory corruption - Part 1(SCGCQ01925503) 
 - Incorrect help option for set autoconfig in StorCli's Help(SCGCQ01932035) 
 - Unmap enabled property is shown in VD detailed properties when controller does not support unmap	(SCGCQ01932177) 
 - Unified StorCLI - Aero : "FullFlashImage" environmental variable component stamp change(SCGCQ01963738) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for /cx/px commands.(SCGCQ02018137) 
 - MR_7.10_Storcli: Instance Validation Failed between "enclosure-schema.json" and "/call/eall show" JSON output.(SCGCQ02018322) 
 - MR_7.10_Storcli: Instance Validation Failed between "foreign-configuration-schema.json" and "/call/fall show"(SCGCQ02024327) 
 - Aero UTP: storclif /call show commands output contains "Count 4 exceeded for token id #"	(SCGCQ02034064) 
 - Aero IT - PA1 - StorCLI - BIOS verion not displayed with flash file using 'show file' command(SCGCQ02034490) 
 - failure in StorCLI enclosure show status	(SCGCQ02040640) 
 - unmap attribute is not mentioned in help file command "add vd each r0".(SCGCQ02042106) 
 - Incorrect status displayed for pause rebuild command.(SCGCQ02043610) 
 - PH11 PA - StorCLI - Segmentation fault seen when 'compare linkspeed' executed on Fury C0 board(SCGCQ02044777) 
 - Port information is not displayed for Vses Backplane(SCGCQ02053070) 
 - "c0 delete ?" does not list snapdump command.(SCGCQ02053639) 
 - Incorrect status displayed for resume copyback command.(SCGCQ02062834) 
 - Aero (DBU PA2): Storcli: Instance Validation Failed bw "vd-operations-migrate-schema.json" & "start_migrate"(SCGCQ02062960) 
 - Aero (DBU PA2): Storcli: Result shows blank for "resume patrolread" failure case.(SCGCQ02064795) 
 - Fail to set the linkconfig .	(SCGCQ02070797) 
 - Storcli /c2 set linkconfig conname=c0,c1 configid=14 returns invalid syntax error(SCGCQ02070953) 
 - Aero DBU PA2 : Syntax error is seen in storcli /cx(x|all	(SCGCQ02077085) 
 - Aero (DBU PA2): Storcli: Syntax error for "/c0 download psoc/efibios/cpld/fcode ?" download commands.(SCGCQ02077175) 
 - Storcli throws different error messages for show status command in Ventura and Aero(SCGCQ02078409) 
 - Incorrect string displayed in show command in FreeBSD OS(SCGCQ02082949) 
 - MR_7.10_Storcli: "storcli show file=filepath" command shows failure status.(SCGCQ02085630) 
 - PCI Linkconfig configid status is failure, even though it was set(SCGCQ02086669) 
 - Storecli_Aero: Using latest storecli show file command "Aero-DVT -HBA 9500-16e" board output version number shows wrong.(SCGCQ02089427) 
 - Libmods changes for defect SCGCQ02062957(SCGCQ02089862) 
 - Help update for "add vd cachevd" command as Normal VD is created with failure status.(SCGCQ02091155) 
 - Preserved cache help file shows a mismatch in command and the convention.(SCGCQ02106218) 
 - Aero DBU PA4 : Storcli doesn't show the convention details properly for storclio /cx/px show command(SCGCQ02113377) 
 - Aero (DBU PA4):Storcli: Syntax error for /c0 show AliLog ?(SCGCQ02113506) 
 - Aero (DBU PA4):Storcli: Typo in /c0 add vd detailed help.(SCGCQ02119091) 
 - Misleading error msg "157 Failed Cannot mix unmap and non-unmap physical drives in same array"(SCGCQ02151484) 
 - Cryptographic erase field is shown "yes" but crypto erase fails.(SCGCQ02175346) 
 - Device Type for non-UBM backplanes are being shown as Enclosure instead of Backplane(SCGCQ02101095) 
 - Multiple status messages are displayed in the output	(SCGCQ02073042) 
 - Controller health status is shown as optimal when megacell cable is disconnected.(SCGCQ02021393) 
 - Storcli, should fail the command "get snapdump id=0 file=snapdump.zip norttdump"(SCGCQ01889700) 
 - Shenandoah_StorCLI:32 Binary crashes on giving invalid input to the command storcli.exe /c0/jbod0 show(SCGCQ01905831) 
 - For NVMe drive use the term NVMe instead of PCIe(SCGCQ01923119) 
 - PD show all command displays SSD weargauge details , which is not required.(SCGCQ01927864) 
 - MR_7.10_Storcli: Junk character in error message while creating SED vd with regular HDD drives.(SCGCQ02016701) 
 - MR_7.10_Storcli: Incorrect command syntax mentioned in Schema_mapping_list.xlsx file for "/cx set autoconfig" command.(SCGCQ02018097) 
 - Instance Validation Failed between "vd-operations-bgi-schema.json" and "/call/v1 show bgi " and "show init".(SCGCQ02035551) 
 - Storcli shows incorrect output for delete events command(SCGCQ02045816) 
 - BreakMirror RAID Support coming as Yes, even when Breakmirror is not supported(SCGCQ02048150) 
 - Spell mistake on support ondemand snapdump property of show all output(SCGCQ02053923) 
 - StorCLI displays expansion as successful even when there is no free space to expand(SCGCQ02057361) 
 - Instance Validation Failed between "controller-patrolread-schema.json" and "/call resume patrolread"(SCGCQ02062942) 
 - PH11 Alpha - StorCLI - 'show file' command displays incorrect message after reading uploaded bios file(SCGCQ02063689) 
 - Need a space between atleast with StorCLI error message "Unmap is not supported atleast on one device"(SCGCQ02064120) 
 - Storcli:"resource already in use" error message displayed when trying to create VD with one UG and one UBUnsp.(SCGCQ02064828) 
 - Aero (DBU PA2): Storcli: Inconsistency in "add vd" command syntax.(SCGCQ02082196) 
 - Details are displayed twice in "/cx/bbu start ? "(SCGCQ02100905) 
 - Storcli: set termlog shows [=on|off] mentioned as optional.(SCGCQ02113353) 
 - CLI is missing the JBOD PD size for SysPDs when using the "show jbod" command(SCGCQ02132277) 
 - Percli returns “invalid arguments" when trying to create a VD using some PDs already configured in a VD and some U(SCGCQ02122169) 
 - Topology information missing from Storcli output(SCGCQ02048612) 
 -	(SCGCQ02040597) 
 - Unified StorCLI: StorCLI does not return the return code from SLIT/SLIR3 to explorer/command processors(SCGCQ01925156) 
 - Virtual drive reference in Delete Preserved cache command output(SCGCQ01940333) 
 - Storcli not working on large config setup when some of the drives are missing or the system has foreign config.(SCGCQ01940805) 
 - Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01948579) 
 - Shenandoah : Firmware receives incorrect erase type for sanitize crypto erase option(SCGCQ01958564) 
 - Storcli shows BBU present instead of EnergyPAck in HWcfg for StorCLI /cx show all output.(SCGCQ01985592) 
 - Aero:Storcli: Adaptertype shown as UNKNOWN(X0) for Sea (3816_Eval) IT Controller(SCGCQ02008219) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for errorcounters commands.(SCGCQ02018078) 
 - Storcli reported "Boot Volume Supported = NO" eventhough ctrl boot with OS on vd.(SCGCQ02030652) 
 - There is no error message for smart drive failure command.(SCGCQ02040645) 
 - Storcli help file doesn't show recon rate command instead it shows migrate rate.(SCGCQ02046036) 
 - JSON Schema : Updating the schema list with Virtual drive command set(SCGCQ02057360) 
 - storecli_Aero:In linux error message observed in the show output.(SCGCQ02057699) 
 - Checking in JSON schemas(SCGCQ02061305) 
 - Junck character displayed in Virtual SES phy id, when we query phyerror counter for enclosure.(SCGCQ02094970) 
 - Aero (DBU PA3):Storcli: Help of /cx/px reset does not mention about option hard reset.(SCGCQ02100896) 
 - BBU show detailed help does not list "show learn " command.(SCGCQ02100915) 
 - Storcli: Instance Validation Fails for all /call/e65/sall commands where "e65 is not found".(SCGCQ02101564) 
 - Storcli: Remove Nytro supported options in "/cx [start] flush|flushcache [cachecade | ALL]" help.(SCGCQ02113484) 
 - MR7.10 cli return mesg. typo after ctrl restart then immediately running storcli64 /c0 show.(SCGCQ02113833) 
 - Storcli: /c0 compare help lists /c0/px compare command.(SCGCQ02124246) 
 - Serial number not displayed fully in 7.10 StorCLI 007.1017.0000.0000 for IT Controller(SCGCQ02173789) 
 - Hide BBU details from the command "storcli /c0 show alilog" for HPE(SCGCQ01937259) 
 - Disk group is displayed instead of array on HPE platforms(SCGCQ01965366) 
 - MR_7.10_Storcli: unmap attribute is not mentioned in "/c0 add vd" command syntax in Schema_mapping_list.xlsx file.(SCGCQ02016758) 
 - Storcli pop-up a message "controller not found" during chip reset , rather than controller busy.(SCGCQ02024740) 
 - "Invalid RAID level" error message while creating R10 VD.(SCGCQ02034471) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-patrolread-schema.json" and "/call pause patrolread"(SCGCQ02035437) 
 - Instance Validation Failed for "/call show and /call show all".(SCGCQ02101432) 
 - Instance Validation Failed bw "drive-group-detailed-schema.json" and "/call/dall show all".(SCGCQ02101513) 
 - Autoconfig options are allowed to set with latest storcli(SCGCQ02053643) 
 - Unified StorCLI Phase 10 : Image checksum should not be performed for aero images(SCGCQ01942200) 
 - Aero DBU PA1:Storcli: Instance Validation Failed "controller-properties-schema" and "/call show" command.(SCGCQ02035439) 
 - Fixing coverity issues Fixing resource leaks and explicit NULL dereferencings(SCGCQ02042242) 
 - Unified StorCLI : Fixing resource leaks - Part 1(SCGCQ02042513) 
 - Updating Schema mapping doc and fixing validation errors	(SCGCQ02057434) 
 - Storcli: Instance Validation Fails for vd-bootdrive-schema.json and vd-unmap-schema.json.(SCGCQ02101568) 
 - Aero_storecli:Using latest storecli firmware download fail with noreset option.(SCGCQ02101570) 
 - Aero DBU PA4 : Syntax error is seen for the command - storclio.efi /cx/px set state ?(SCGCQ02113123) 
 - PD info incorrectly shows Number of Blocks for >TB drives(>3TB in my case(SCGCQ02183653) 
 - CLI is returning "success" when attempting to set bios mode to Ignore Errors.(SCGCQ02121017) 
 - On Demand SnapDump does not show proper time stamp.(SCGCQ02084833) 
 - Storcli issuing 'add jbod drives=all' causes storcli to crash(SCGCQ01892288) 
 - Initialize the MFG structure(SCGCQ01901166) 
 - Aero:Storcli: Adaptertype shown as UNKNOWN(X0) for Aero (3916_Eval) IT Controller(SCGCQ02021194) 
 - Instance Validation Failed between "drive-group-schema.json" and "/call/dall show " and /call/dall show all(SCGCQ02040756) 
 - PH11 PA Storcli: Incorrect error message shown while programming invalid sasaddress(SCGCQ02042296) 
 - Unified StorCLI : Individual SL_INIT_LIB calls are made for every SL command invocation(SCGCQ02047100) 
 - Updating storcli-cmd-list.xlsx for Drives(SCGCQ02056199) 
 - Message with Incorrect controller object is displayed while setting SSD Caching on VD(SCGCQ02057085) 
 - Storcli displays grammatically incorrect message in detailed help file.(SCGCQ02097641) 
 - MR_7.10: Storcli: Property is shown as SCSI Umap instead of SCSI Unmap.(SCGCQ02101572) 
 - Storcli: /c0 show detailed command does not list /cx/px show phyerrorcounters and /cx show vpd.(SCGCQ02113262) 
 - Aero (DBU PA4):Storcli: Incorrect description of "/c0/v0 show migrate" command.(SCGCQ02113511) 
 - Wrong reference of "page=[X]" as part of syntax error message.(SCGCQ02124252) 
 - Storcli: Junk character in PD start locate command description.(SCGCQ02125654)
 - Storcli doesn't exit with controller status message after doing OFU.	(SCGCQ02101069 port of SCGCQ02091548) 
 - perccli /c0 show all lists topology without any DG's present	(SCGCQ02085925 port of SCGCQ01998332) 
 - MR_7.10_Storcli: bbu-show-modes-schema.json file is not in JSON format.(SCGCQ02079618 port of SCGCQ02019740) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for drive jbod commands.(SCGCQ02079592 port of SCGCQ02018135) 
 - Libmods: HPE serial number display(SCGCQ02062634 port of SCGCQ01885657) 
 - Aero DBU PA1:Storcli: Instance Validation Failed "controller-properties-schema" and "/call show" command.(SCGCQ02061387 port of SCGCQ02035439) 
 - MR_7.10_Storcli: unmap attribute is not mentioned in "/c0 add vd" command syntax in Schema_mapping_list.xlsx file.(SCGCQ02050535 port of SCGCQ02016758) 
 - MR_7.10_Storcli: Instance Validation Failed between "virtual-drive-detailed-schema.json" and "/call/vall show all "(SCGCQ02050471 port of SCGCQ02018333) 
 - failure in StorCLI enclosure show status	(SCGCQ02043616 port of SCGCQ02040640) 
 - Expander FW download using storecli utility crashs.(SCGCQ01979616 port of SCGCQ01979599) 
 - Hide "set pdfaileventoptions" command from CLI Help(SCGCQ01892551 port of SCGCQ01880722) 
 - Error message when Maximum number of VDs are reached	(SCGCQ01911777 port of SCGCQ01856544) 
 - Adding CLI command to display/toggle new controller property.(SCGCQ01927583 port of SCGCQ01106982) 
 - System hangs while creating VD in EFI shell.(SCGCQ01945574 port of SCGCQ01945551) 
 - storclio command not working to update FW on SATA disk(SCGCQ01963953 port of SCGCQ01918814) 
 - Storcli is not showing foreign configs if user has SED drive which is in foreign(SCGCQ01963954 port of SCGCQ01937410) 
 - Restricting PD FW download enable command to FW for SATA drives(SCGCQ01964173 port of SCGCQ01955389) 
 - Add security-related compilation and linker flags to StorCLI - Linux	(SCGCQ01966163 port of SCGCQ01892560) 
 - Unified StorCLI : Enclosure devices are part of drive list used for drive operations	(SCGCQ01982925 port of SCGCQ01979483) 
 - Unified LibMod changes : Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01985486 port of SCGCQ01893074) 
 - Enable iMR advanced debug dump(SCGCQ02035300 port of SCGCQ01873124) 
 - Drive Size Display Miss Match In Storcli Show Output	(SCGCQ02074659 port of SCGCQ02072353) 
 - HDET:Libmods-Boot device should be presented as /dev/sda in Linux operating system during installation and post installation	(SCGCQ02082198 port of SCGCQ02046182) 
 - HDET: Boot device should be presented as /dev/sda in Linux operating system during installation and post installation(SCGCQ02082199 port of SCGCQ02016712) 
 - BSOD observed when VD/JBOD Creation/Del and snapdump Cycles are initiated.(SCGCQ02085669 port of SCGCQ02045967) 
 - storclif /cx delete colinfo ? shows syntax error	(SCGCQ02124654 port of SCGCQ02124492) 
 - PH12 PA - StorCLI /cx/pall show fails on 9400-8e board(SCGCQ02128167 port of SCGCQ02119004) 
 - Storcli: Force option not mentioned in "/cx/dx add mirror" and "/cx/vx start init" command.(SCGCQ02142248 port of SCGCQ02140878) 
 - Aero (DBU PA5):Storcli: No description of patrolread "OFF" and optional is mentioned as {}.(SCGCQ02145876 port of SCGCQ02140859) 
 - PERCCLI to support creation of VD with WB policy for PERC8 MR(SCGCQ01892550 port of SCGCQ01891650) 
 - MR: 64 Bit Utilities/Application to Support VMWARE ESXi 6.7+	(SCGCQ02139866 port of SCGCQ02066386) 
 - Libmod changes for SCGCQ02090770(SCGCQ02097658 port of SCGCQ02090770) 
 - Wide port info is not displayed under connector name for Backplane attached drives.(SCGCQ02085666 port of SCGCQ02076923) 
 - CLI returns wrong error code upon failure(SCGCQ02085528 port of SCGCQ02084966) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON output.(SCGCQ02079591 port of SCGCQ02018305) 
 - Storcli displays drive state as UBad instead of UBad (unsupported(SCGCQ02079521 port of SCGCQ02031615) 
 - Storcli: "resume migrate" command does not show syntax error.(SCGCQ02075292 port of SCGCQ02061340) 
 - BreakMirror RAID Support coming as Yes, even when Breakmirror is not supported(SCGCQ02075281 port of SCGCQ02048150) 
 - Drive Size Display Miss Match In Storcli Show Output	(SCGCQ02075280 port of SCGCQ02072353) 
 - Typo in storcli /c0 set linkspeed help(SCGCQ02074664 port of SCGCQ02070951) 
 - PH11 Alpha - StorCLI - 'show file' command displays incorrect message after reading uploaded bios file(SCGCQ02064703 port of SCGCQ02063689) 
 - Storcli reported "Boot Volume Supported = NO" eventhough ctrl boot with OS on vd.(SCGCQ02047809 port of SCGCQ02030652) 
 - Storcli help file doesn't show recon rate command instead it shows migrate rate.	(SCGCQ02047747 port of SCGCQ02046036) 
 - Storcli shows incorrect output for delete events command(SCGCQ02046875 port of SCGCQ02045816) 
 - Unified StorCLI : Enclosure devices are part of drive list used for drive operations	(SCGCQ01979535 port of SCGCQ01979483) 
 - enhance warning message for personality switch indicating interruption could cause controller to be unstable(SCGCQ01892552 port of SCGCQ01892549) 
 - Storcli, should fail the command "get snapdump id=0 file=snapdump.zip norttdump"	(SCGCQ01906745 port of SCGCQ01889700) 
 - StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911831 port of SCGCQ01886637) 
 - 6.13_SDS : Wrong error message is displayed on trying to create R0 vd on an pre configured drive as EPD.(SCGCQ01925211 port of SCGCQ01196785) 
 - Square bracket is missing in the syntax of "set hardware device page" in storclio.(SCGCQ01929137 port of SCGCQ01224857) 
 - For NVMe drive use the term NVMe instead of PCIe	(SCGCQ01963960 port of SCGCQ01923119) 
 - StorCLI show SAS address for NVMe drives	(SCGCQ01963964 port of SCGCQ01921258) 
 - JBOD list is not showing in order when using /cx show(SCGCQ01965193 port of SCGCQ01961527) 
 - Added Windows compiler security flags (SDL and control flow guard(SCGCQ01965209 port of SCGCQ01949495) 
 - supported personalities has blank value	(SCGCQ01971366 port of SCGCQ01965370) 
 - Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01977028 port of SCGCQ01948579) 
 - Expander FW download using storecli utility crashs.(SCGCQ01979617 port of SCGCQ01979599) 
 - WBSup abbreviation defined twice when running perccli /cX show profile(SCGCQ01995022 port of SCGCQ01993282) 
 - spell mistake in start diag operation failure(SCGCQ01998963 port of SCGCQ01998330) 
 - Proper message to be given on VD creation with wb option while Battery not connected/Failed(SCGCQ02028787 port of SCGCQ01972504) 
 - iMR Changing profileid's using cli results in Status=Success Description=None(SCGCQ02028810 port of SCGCQ02008676) 
 - Enable iMR advanced debug dump(SCGCQ02035289 port of SCGCQ02030908) 
 - On Demand SnapDump does not show proper time stamp.(SCGCQ02085609 port of SCGCQ02084833) 
 - Flashing of Completeflash fails on Sea IT controller(SCGCQ02139848 port of SCGCQ02139780) 
 - Storcli: "Ctrl" legend not mentioned.(SCGCQ02150640 port of SCGCQ02146822) 
 - storcli -help missing the verbose option	(SCGCQ02160908 port of SCGCQ02158600) 
 - MR7.11_Storcli: Incorrect error description while creating r1 with single drive(SCGCQ02168183 port of SCGCQ02165933) 
 - Phase 12 - Oct Huawei DET - Incorrect Phy Details Displayed for Ventura IT Controller(SCGCQ02179296 port of SCGCQ02174296) 
 - Incorrect Help Menu For "show phyerrorcounters"(SCGCQ02180519 port of SCGCQ02180495) 
 - Recon command (./storcli /cx set recon(SCGCQ02086570 port of SCGCQ02081415) 
 - Need a space between atleast with StorCLI error message "Unmap is not supported atleast on one device"(SCGCQ02075290 port of SCGCQ02064120) 
 - Show Snapdump help command lists delete snapdump details as well.(SCGCQ02075287 port of SCGCQ02064836) 
 - iMR Changing profileid's using cli results in Status=Success Description=None(SCGCQ02056156 port of SCGCQ02008676) 
 - Spell mistake on support ondemand snapdump property of show all output(SCGCQ02053926 port of SCGCQ02053923) 
 - Unified StorCLI : Individual SL_INIT_LIB calls are made for every SL command invocation(SCGCQ02047893 port of SCGCQ02047100) 
 - Instance Validation Failed between "drive-group-hidden-schema" and "/c1/dall set hidden" & "set security"(SCGCQ02047136 port of SCGCQ02040779) 
 - unmap attribute is not mentioned in help file command "add vd each r0".(SCGCQ02047095 port of SCGCQ02042106) 
 - Storcli pop-up a message "controller not found" during chip reset , rather than controller busy.	(SCGCQ02047079 port of SCGCQ02024740) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ02009900 port of SCGCQ01761309) 
 - storcli faults for enclosure show command(SCGCQ01986423 port of SCGCQ01985815) 
 - storclio command not working to update FW on SATA disk(SCGCQ01922919 port of SCGCQ01918814) 
 - Restricting PD FW download enable command to FW for SATA drives(SCGCQ01964153 port of SCGCQ01955389) 
 - StorCLI crashes, while trying to enable security on any DG ,incase, when no DG exists(SCGCQ01965185 port of SCGCQ01413253) 
 - Added Windows compiler security flags (SDL and control flow guard(SCGCQ01965210 port of SCGCQ01949503) 
 - Unified LibMod changes : Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01966261 port of SCGCQ01893074) 
 - Add security-related compilation and linker flags to StorCLI - Linux	(SCGCQ01985558 port of SCGCQ01892560) 
 - Snapdump unsupported commands for HPE needs to be disabled(SCGCQ01996375 port of SCGCQ01985589) 
 - MR_7.9: Storcli reported unknown OS for Windows 10 RS5 LTSC.(SCGCQ02009848 port of SCGCQ01992461) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ02011417 port of SCGCQ01761309) 
 - StorcliO show oob command fails for Invader based cards(SCGCQ02043788 port of SCGCQ02040783) 
 - Storclif doesn't show details for VF/PF in help file for vfmap command .(SCGCQ02124488 port of SCGCQ02123789) 
 - Storcli: "completeflash" is listed in Windows help file.(SCGCQ02145743 port of SCGCQ02141931) 
 - Storcli: /c0 set ? lists bbu,mx,px and lnx commands.	(SCGCQ02145756 port of SCGCQ02136689) 
 - Configuring multiple lane speed is working only for fisrt ID, Rest were ignored(SCGCQ02145764 port of SCGCQ02136333) 
 - Help note 'page=[x]' needs update(SCGCQ02149062 port of SCGCQ02146823) 
 - Instance Validation Failed for "/call/eall show status extended" and enclosure-status-extended-schema.json(SCGCQ02153948 port of SCGCQ02150924) 
 - Instance Validation Failed for /call/show_all.json and controller-detailed-properties-schema.json(SCGCQ02154721 port of SCGCQ02135526) 
 - StorCLI listing PD Slot Status as "Incorrect Status Value" for configured PD's(SCGCQ02097676 port of SCGCQ02090770) 
 - Aero (DBU PA2(SCGCQ02086670 port of SCGCQ02082460) 
 - storclif.exe /c0/ex/sx show poh should show proper message during command execution.(SCGCQ02086632 port of SCGCQ02075242) 
 - show/set lane speed shows success when we are in SAS profile(SCGCQ02079507 port of SCGCQ02078437) 
 - Storcli: "show config" command shown as Un-supported.(SCGCQ02075286 port of SCGCQ02064839) 
 - Schema file updates for controller show all output change for defect SCGCQ02048150(SCGCQ02075282 port of SCGCQ02069817) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for "/cx get vpd" commands.(SCGCQ02058567 port of SCGCQ02018140) 
 - Instance Validation Failed between "vd-unmap-schema.json" and "/call/vall show unmap"(SCGCQ02047243 port of SCGCQ02035370) 
 - Instance Validation Failed between "drive-group-schema.json" and "/call/dall show " and /call/dall show all	(SCGCQ02047235 port of SCGCQ02040756) 
 - PH11 PA - StorCLI - Segmentation fault seen when 'compare linkspeed' executed on Fury C0 board(SCGCQ02044794 port of SCGCQ02044777) 
 - Request to Disable DSW3(SCGCQ01903331 port of SCGCQ01896311) 
 - PERCCLI Support for EKMS(SCGCQ01904188 port of SCGCQ01902150) 
 - StorCLI crashes, while trying to enable security on any DG ,incase, when no DG exists(SCGCQ01904340 port of SCGCQ01413253) 
 - Disk performance throttled when running MegaCli AdpEvent log dump on Aspen and Vail (Invader and Intruder(SCGCQ01921529 port of SCGCQ01220901) 
 - Hide "set termlog" help contents from perccli(SCGCQ01935143 port of SCGCQ01923643) 
 - Storcli is not showing foreign configs if user has SED drive which is in foreign(SCGCQ01940869 port of SCGCQ01937410) 
 - Storcli not working on large config setup when some of the drives are missing or the system has foreign config.(SCGCQ01945534 port of SCGCQ01940805) 
 - Storcli- Delay seen in /c0 /vall show all o/p(SCGCQ01965393 port of SCGCQ01935697) 
 - Storcli shows wrong PD list sequence.(SCGCQ01971632 port of SCGCQ01967488) 
 - LD size not shown in GiB format in foreign import preview(SCGCQ01996370 port of SCGCQ01978978) 
 - Unable to switch to eHBA mode using a H745P Adapter(SCGCQ01998964 port of SCGCQ01990060) 
 - perccli show profile lists personality as JBOD instead of eHBA(SCGCQ01998966 port of SCGCQ01998328) 
 - Json Schema for the command "storcli /cx/ex show phyerrorcounters" needs to be updated(SCGCQ02101377 port of SCGCQ02101372) 
 - In ARM server UEFI shell, storcli.efi hangs forever when storcliconf.ini is present(SCGCQ02116733 port of SCGCQ02115036) 
 - complete Lane WWID is not displayed(SCGCQ02145739 port of SCGCQ02145716) 
 - No "Rbld" legend during rebuild.	(SCGCQ02150634 port of SCGCQ02146819) 
 - Error message mismatch is seen for rttdump command on iMR Ventura controller.(SCGCQ02160907 port of SCGCQ02156483) 
 - Storcli throws different error messages for show status command in Ventura and Aero(SCGCQ02086689 port of SCGCQ02078409) 
 - Multiple status messages are displayed in the output	(SCGCQ02086536 port of SCGCQ02073042) 
 - MR_7.10_Storcli: No schema file for controller sesmultipathcfg commands.(SCGCQ02079595 port of SCGCQ02018134) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" JSON output.(SCGCQ02079590 port of SCGCQ02018277) 
 - "Run time to empty" field showing as "Battery is not being charged" when the battery is being charged.(SCGCQ02079535 port of SCGCQ02045324)
 - MR_7.10_Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set personality" JSON output.(SCGCQ02050491 port of SCGCQ02016762) 
 - MR_7.10_Storcli: Add VD command output is not in JSON format.(SCGCQ02050489 port of SCGCQ02034493) 
 - "Invalid RAID level" error message while creating R10 VD.(SCGCQ02047806 port of SCGCQ02034471) 
 - Incorrect status displayed for pause rebuild command.(SCGCQ02046878 port of SCGCQ02043610) 
 - PH11 PA Storcli: Incorrect error message shown while programming invalid sasaddress(SCGCQ02043612 port of SCGCQ02042296) 
 - Aero UTP: storclif /call show commands output contains "Count 4 exceeded for token id #"	(SCGCQ02034200 port of SCGCQ02034064) 
 - Storcli shows wrong PD list sequence.(SCGCQ01977461 port of SCGCQ01967488) 
 - Migrate Failure case is not Branding compliant(SCGCQ02000716 port of SCGCQ01988402) 
 - StorCLI PH12: Retrieving topology details causes application crash in some scenario(SCGCQ02106192 port of SCGCQ02103217) 
 - Support FMP Images in UEFI Version of PERCCli(SCGCQ02116464 port of SCGCQ02078649) 
 - MR 7.11: Storcli.efi: On ARM server, incomplete configuration data received error is observed for any storcli.efi command(SCGCQ02116497 port of SCGCQ02114898) 
 - PH12 PA - StorCLI - 9310-8i IR FW download fails	(SCGCQ02121848 port of SCGCQ02121783) 
 - LibMod changes : MR: 64 Bit Utilities/Application to Support VMWARE ESXi 6.7+(SCGCQ02139867 port of SCGCQ02085102) 
 - MR7.11_Storcli: On drive rebuild, there is a mismatch between the pd rebuild state and respective legend	(SCGCQ02168256 port of SCGCQ02165944) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for /cx/px commands.(SCGCQ02079604 port of SCGCQ02018137) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-patrolread-schema.json" and "/call pause patrolread"(SCGCQ02079597 port of SCGCQ02035437) 
 - Empty data is listed when we query for show linkconfig(SCGCQ02079511 port of SCGCQ02076931) 
 - Libmods: show.set lane speed shows success with wrong data when we are in SAS profile(SCGCQ02079506 port of SCGCQ02078513) 
 - Incorrect status displayed for resume copyback command.	(SCGCQ02075291 port of SCGCQ02062834) 
 - "Delete snapdump" command shows same description "Snapdump clear" for success and failure case.(SCGCQ02075284 port of SCGCQ02065734) 
 - MR_7.10_Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/eall/sall show all"(SCGCQ02050481 port of SCGCQ02018327) 
 - Libmod changes: Adding CLI command to display/toggle new controller property.(SCGCQ01106982(SCGCQ01929892 port of SCGCQ01106988) 
 - Added new commands from StorCLI(SCGCQ01935296 port of SCGCQ01134166) 
 - For NVMe drive use the term NVMe instead of PCIe	(SCGCQ01964024 port of SCGCQ01923119) 
 - securesed autoconfig param should not be present for perccli help(SCGCQ01986879 port of SCGCQ01986831) 
 - Extend major downgrade support in storCLI for SAS3 IT product(SCGCQ02032582 port of SCGCQ02029410) 
 - Drives connected to active backplanes not showing the phy info in connector name	(SCGCQ02112425 port of SCGCQ02112424) 
 - Background operations keep on progressing after hitting /c0 shutdown from storcli(SCGCQ02150630 port of SCGCQ02132024) 
 - Instance Validation Failed for "/call/eall show status" and enclosure-status-schema.json(SCGCQ02153950 port of SCGCQ02150921) 
 - Instance Validation Failed for "/call/cv show all" and cache-vault-detailed-schema.json(SCGCQ02154755 port of SCGCQ02150651) 
 - Storcli: Force is mentioned as optional in snapdump delete command.(SCGCQ02086544 port of SCGCQ02083822) 
 - Port information is not displayed for Vses Backplane	(SCGCQ02085875 port of SCGCQ02053070) 
 - MR_7.9: Storcli reported unknown OS for Windows 10 RS5 LTSC.	(SCGCQ02079601 port of SCGCQ01992461) 
 - spell mistake in start diag operation failure(SCGCQ02079529 port of SCGCQ01998330) 
 - Storcli:"resource already in use" error message displayed when trying to create VD with one UG and one UBUnsp.(SCGCQ02075289 port of SCGCQ02064828) 
 - Storcli: HPE serial number programming and display(SCGCQ02062635 port of SCGCQ01882984) 
 - MR_7.10_Storcli: Instance Validation Failed between "cache-vault-detailed-schema.json" and "/call/cv show all "(SCGCQ02050460 port of SCGCQ02019729) 
 - FW flash fails to load the latest image after upgrade downgrade with resetnow option	(SCGCQ02046879 port of SCGCQ02035152) 
 - Extend major downgrade support in storCLI for SAS3 IT product(SCGCQ02032581 port of SCGCQ02029410) 
 - Storcli throws an 'Incomplete foreign configuration' error when there is no enclosure connected(SCGCQ02007109 port of SCGCQ02006450) 
 - Storcli issuing 'add jbod drives=all' causes storcli to crash(SCGCQ01893381 port of SCGCQ01892288) 
 - LibMods : Adding the function that changing flag of full initialize completion(SCGCQ01930028 port of SCGCQ01141462) 
 - Storcli- Delay seen in /c0 /vall show all o/p(SCGCQ01936895 port of SCGCQ01935697) 
 - Terminology change from " Data protection" to " Data integrity".(SCGCQ01940807 port of SCGCQ01827339) 
 - Libmods: Terminology change from " Data protection" to " Data integrity".(SCGCQ01943370 port of SCGCQ01827732) 
 - Incorrect colinfo output of Bad block count(SCGCQ01977457 port of SCGCQ01977443) 
 - StorCLI hangs when viewing controller in FreeBSD (MR7.8 is okay(SCGCQ01984543 port of SCGCQ01978824) 
 - Unified StorCLI : Help command of "Get flash" is not shown in generic help syntax(SCGCQ01985472 port of SCGCQ01985463) 
 - StorCLI show output shows Legends as BBU instead of EnergyPack.(SCGCQ01992007 port of SCGCQ01985587) 
 - Aero A0 UTP: StorCLI snapdump command needs to clarify new "On Demand" snapdump option(SCGCQ01995066 port of SCGCQ01993722) 
 - Shenandoah:StorCLI:Right click properties for released binary shown blank.(SCGCQ02000843 port of SCGCQ01988329) 
 - Smart Carrier Enclosure port info shown as "Multuipath"(SCGCQ02008273 port of SCGCQ01992087) 
 - MR 7.11: Storcli: Instance Validation Failed for "/call show all" and system-schema.json	(SCGCQ02116771 port of SCGCQ02112192) 
 - "Storcli /c# set jbod=on" shows success but does nothing	(SCGCQ02119067 port of SCGCQ02117219) 
 - Phyreset Fails on IT controllers	(SCGCQ02169305 port of SCGCQ02169242) 
 - Storcli stop erase needs an help file update	(SCGCQ02169308 port of SCGCQ02168895) 
 - Updating phy link reset logic for IT cards with respect to storelib changes(SCGCQ02185911 port of SCGCQ02184862) 
 - Storcli connector display not matching with Aero board 9560-16i.	(SCGCQ02085681 port of SCGCQ02072448) 
 - MR_7.10_Storcli: controller-detailed-properties-schema.json or "/call show all " output not in JSON format(SCGCQ02079610 port of SCGCQ02016771) 
 - MR_7.10_Storcli: No schema file for controller unmap commands.(SCGCQ02079593 port of SCGCQ02016749) 
 - Incorrect error message displayed while creating R10 VD when no free space available.(SCGCQ02075283 port of SCGCQ02067575) 
 - remove the maxconcurrentpd check from storcli and report fw returned failure	(SCGCQ02053931 port of SCGCQ02053910) 
 - PERCCLI Support for EKMS	(SCGCQ01904189 port of SCGCQ01903448) 
 - StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911832 port of SCGCQ01886637) 
 - Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder(SCGCQ01915313 port of SCGCQ01222855) 
 - (Libmods) Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder)(SCGCQ01915315 port of SCGCQ01227144) 
 - perccli /c0 show all lists topology without any DG's present(SCGCQ01998965 port of SCGCQ01998332) 
 - PH12 PA - StorCLI version not getting printed for show file command	(SCGCQ02116759 port of SCGCQ02105185) 
 - Convention comes in same line while performing help for /c0/e0/s0 download.(SCGCQ02176697 port of SCGCQ02176681) 
 - With IT controller for set or reset with invalid phy is not showing error(SCGCQ02183510 port of SCGCQ02181823) 
	
EnhancementRequests:
 - Incorporating VMware constraints for PERCCLI VIB signing	(SCGCQ02190441) 
 - Migrating VMware 64 bit toolchain to 6.8.7-13394445(SCGCQ02190429) 
 - Create an event for DDF config clear failed event.(SCGCQ02173513) 
 -	(SCGCQ02162699) 
 - Snap Dump ClearAll Method logging event(SCGCQ02157359) 
 - API changes for a better presentation of Atlas to tools(SCGCQ02149380) 
 - Add disableOffloadNum field in MR_SNAPDUMP_PROPERTIES struct(SCGCQ02125252) 
 - Better error message for certain unmap operations(SCGCQ02111563) 
 - Add MFI STAT and MR Event for Secure Boot indicating fw dl was not allowed due to an existing pending key change(SCGCQ02103973) 
 - MR Windows IOCTL Error codes to Application added to MR API(SCGCQ02103183) 
 - API changes for linkconfig interface	(SCGCQ02053671) 
 - API changes for NVMe speed and width changes	(SCGCQ02053667) 
 - Reword event log messages as it creates unnecessary panic.(SCGCQ02013675) 
 - Added Windows compiler security flags (SDL and control flow guard(SCGCQ01949495) 
 - Unified StorCLI : Adding component level download functionality to StorCLI(SCGCQ01940030) 
 - show complete Serial Number and Model Name for NVMe drive(SCGCQ01927541) 
 - snapdump support for host initiated snapdump	(SCGCQ01901158) 
 - Changes for disable least latency mode(SCGCQ01891451) 
 - Inspur request to add to show smart info of sas drive for "StorCLI /cx/ex/sx show smart" command(SCGCQ01929656) 
 - MR_SAS_Unified_Libmods_7.10 Inspur request to add to show smart info of sas drive for "StorCLI /cx/ex/sx show smart" command(SCGCQ01979597) 
 - Post firmware trace buffer at the time of driver load(SCGCQ01992779) 
 - Adding the spare details in the same volume creation(CONFIG_ADD DCMD(SCGCQ02008407) 
 - PSoC implementation in StorCLI by parsing PSoC image(SCGCQ02072160) 
 - Request to display the help for "show" and "set" for JBOD in PercCLI	(SCGCQ02160291) 
 - Adding NVACHE messages indicate when SLC format has started and completed.(SCGCQ02137048) 
 - MR API: Add support bits for currentSpeed and clkMode(SCGCQ02132334) 
 - Enable iMR advanced debug dump(SCGCQ02030908) 
 - Unified StorCLI : ARM Windows support to StorCLI(SCGCQ01962294) 
 - Disabling RAID00 support	(SCGCQ01960420) 
 - HPE Shenandoah: Branding tool(SCGCQ01960295) 
 - Added Windows compiler security flags (SDL and control flow guard(SCGCQ01949503) 
 - Unified StorCLI : Allow SBR/SPD read and write using new CBB+SBR concatenated image(SCGCQ01927551) 
 - show complete Serial Number and Model Name for NVMe drive connected to IT controller(SCGCQ01927538) 
 - show complete Serial Number and Model Name for NVMe drive(SCGCQ01919655) 
 - Unified CLI - Command processor changes for handling invalid/tampered device id's for sea IT controllers(SCGCQ01891513) 
 - Add support to display PSOC version for Ventura IT controllers(SCGCQ02067300) 
 - set copyback command changes for cli(SCGCQ02148092) 
 - Unified StorCLI : ARM64 Windows support to StorCLI - LibMod changes(SCGCQ01963208) 
 - Shenandoah: Adding support bit check for delete snap dump(SCGCQ01944500) 
 - Enable iMR advanced debug dump(SCGCQ01873124) 
 - Unified StorCLI : PSoC read and write via Device read and write DCMD's in MR Operational case(SCGCQ01949521) 
 - Changes for disable least latency mode(SCGCQ01891442) 
 - Adding the spare details in the same volume creation (CONFIG_ADD DCMD(SCGCQ02008403) 
 - Unified StorCLI : Allow erase functionality on operational MR using CBB concatenated image(SCGCQ01927595) 
 - Unified CLI : Handling invalid/tampered controllers for sea controllers(SCGCQ01891484) 
 - Requesting StorCLIF to read MR FW from flash device and write it to a file. Similar to what IT FW support.(SCGCQ01631948) 
 - Add ability to field upgrade PSOC on HBA boards(SCGCQ01583214) 
 - DUal Image SUpport(SCGCQ01960287) 
 - Libmods: Porting HPE Shenandoah from Aero to 7.9	(SCGCQ01917263) 
 - Porting HPE Shenandoah from Aero to 7.9(SCGCQ01917172) 
 - Adding HPE specific help for storcli	(SCGCQ01935699) 


007.0816.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------

defects:
  - Improve Debuggablity for MegaRAID Windows Driver by Adding RT Trace - new modifications(SCGCQ01824574 port of SCGCQ01824569) 
 - displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state"(SCGCQ01827604 port of SCGCQ01681538) 
 - Updating makefile and EFI's INF changes for ARM StorCLIO(SCGCQ01870684 port of SCGCQ01563125) 
 - Square bracket is missing in the syntax of "set hardware device page" in storclio.(SCGCQ01929787 port of SCGCQ01224857) 
 - failure in StorCLI enclosure show status	(SCGCQ02043616 port of SCGCQ02040640) 
 - MR_7.10_Storcli: Instance Validation Failed between "virtual-drive-detailed-schema.json" and "/call/vall show all "(SCGCQ02050471 port of SCGCQ02018333) 
 - MR_7.10_Storcli: unmap attribute is not mentioned in "/c0 add vd" command syntax in Schema_mapping_list.xlsx file.(SCGCQ02050535 port of SCGCQ02016758) 
 - Aero DBU PA1:Storcli: Instance Validation Failed "controller-properties-schema" and "/call show" command.(SCGCQ02061387 port of SCGCQ02035439) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for drive jbod commands.(SCGCQ02079592 port of SCGCQ02018135) 
 - MR_7.10_Storcli: bbu-show-modes-schema.json file is not in JSON format.(SCGCQ02079618 port of SCGCQ02019740) 
 - perccli /c0 show all lists topology without any DG's present(SCGCQ02085925 port of SCGCQ01998332) 
 - Libmod changes for StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers(SCGCQ01853370 port of SCGCQ01775616) 
 - (SCGCQ01775602 port of SCGCQ01814011)
 - show enclosure command is not exiting to shell(SCGCQ01874899 port of SCGCQ01814011) 
 - StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911831 port of SCGCQ01886637) 
 - Storcli shows incorrect output for delete events command	(SCGCQ02046875 port of SCGCQ02045816) 
 - Storcli help file doesn't show recon rate command instead it shows migrate rate.(SCGCQ02047747 port of SCGCQ02046036) 
 - Storcli reported "Boot Volume Supported = NO" eventhough ctrl boot with OS on vd.(SCGCQ02047809 port of SCGCQ02030652) 
 - PH11 Alpha - StorCLI - 'show file' command displays incorrect message after reading uploaded bios file(SCGCQ02064703 port of SCGCQ02063689) 
 - Typo in storcli /c0 set linkspeed help(SCGCQ02074664 port of SCGCQ02070951) 
 - Drive Size Display Miss Match In Storcli Show Output(SCGCQ02075280 port of SCGCQ02072353) 
 - BreakMirror RAID Support coming as Yes, even when Breakmirror is not supported(SCGCQ02075281 port of SCGCQ02048150) 
 - Storcli: "resume migrate" command does not show syntax error.(SCGCQ02075292 port of SCGCQ02061340) 
 - Storcli displays drive state as UBad instead of UBad (unsupported(SCGCQ02079521 port of SCGCQ02031615) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON output.(SCGCQ02079591 port of SCGCQ02018305) 
 - CLI returns wrong error code upon failure(SCGCQ02085528 port of SCGCQ02084966) 
 - Wide port info is not displayed under connector name for Backplane attached drives.(SCGCQ02085666 port of SCGCQ02076923) 
 - Libmod changes for SCGCQ02090770	(SCGCQ02097658 port of SCGCQ02096774) 
 - Hide/Unhide command output display incorrect VD no for VDs on which the operation is not supported(SCGCQ01850374 port of SCGCQ01837932) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ02009900 port of SCGCQ01761309) 
 - Storcli pop-up a message "controller not found" during chip reset , rather than controller busy.(SCGCQ02047079 port of SCGCQ02024740) 
 - unmap attribute is not mentioned in help file command "add vd each r0".(SCGCQ02047095 port of SCGCQ02042106) 
 - Instance Validation Failed between "drive-group-hidden-schema" and "/c1/dall set hidden" & "set security"(SCGCQ02047136 port of SCGCQ02040779) 
 - Unified StorCLI : Individual SL_INIT_LIB calls are made for every SL command invocation(SCGCQ02047893 port of SCGCQ02047100) 
 - Spell mistake on support ondemand snapdump property of show all output(SCGCQ02053926 port of SCGCQ02053923) 
 - iMR Changing profileid's using cli results in Status=Success Description=None(SCGCQ02056156 port of SCGCQ02008676) 
 - Show Snapdump help command lists delete snapdump details as well.(SCGCQ02075287 port of SCGCQ02064836) 
 - Need a space between atleast with StorCLI error message "Unmap is not supported atleast on one device"(SCGCQ02075290 port of SCGCQ02064120) 
 - Recon command (./storcli /cx set recon(SCGCQ02086570 port of SCGCQ02081415) 
 - Enhance the detailed help for Firmware download and get bios command.(SCGCQ01792109 port of SCGCQ01790167) 
 - PH11 PA - StorCLI - Segmentation fault seen when 'compare linkspeed' executed on Fury C0 board(SCGCQ02044794 port of SCGCQ02044777) 
 - Instance Validation Failed between "drive-group-schema.json" and "/call/dall show " and /call/dall show all(SCGCQ02047235 port of SCGCQ02040756) 
 - Instance Validation Failed between "vd-unmap-schema.json" and "/call/vall show unmap"(SCGCQ02047243 port of SCGCQ02035370) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for "/cx get vpd" commands.(SCGCQ02058567 port of SCGCQ02018140) 
 - Schema file updates for controller show all output change for defect SCGCQ02048150(SCGCQ02075282 port of SCGCQ02069817) 
 - Storcli: "show config" command shown as Un-supported.(SCGCQ02075286 port of SCGCQ02064839) 
 - show/set lane speed shows success when we are in SAS profile	(SCGCQ02079507 port of SCGCQ02078437) 
 - storclif.exe /c0/ex/sx show poh should show proper message during command execution.(SCGCQ02086632 port of SCGCQ02075242) 
 - Aero (DBU PA2)(SCGCQ02086670 port of SCGCQ02082460) 
 - StorCLI listing PD Slot Status as "Incorrect Status Value" for configured PD's(SCGCQ02097676 port of SCGCQ02090770) 
 - Error message when Maximum number of VDs are reached	(SCGCQ01857450 port of SCGCQ01856544) 
 - Aero UTP: storclif /call show commands output contains "Count 4 exceeded for token id #"	(SCGCQ02034200 port of SCGCQ02034064) 
 - PH11 PA Storcli: Incorrect error message shown while programming invalid sasaddress(SCGCQ02043612 port of SCGCQ02042296) 
 - Incorrect status displayed for pause rebuild command.(SCGCQ02046878 port of SCGCQ02043610) 
 - "Invalid RAID level" error message while creating R10 VD.(SCGCQ02047806 port of SCGCQ02034471) 
 - MR_7.10_Storcli: Add VD command output is not in JSON format.(SCGCQ02050489 port of SCGCQ02034493) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set personality" JSON output.(SCGCQ02050491 port of SCGCQ02016762) 
 - "Run time to empty" field showing as "Battery is not being charged" when the battery is being charged.(SCGCQ02079535 port of SCGCQ02045324) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" JSON output.(SCGCQ02079590 port of SCGCQ02018277) 
 - MR_7.10_Storcli: No schema file for controller sesmultipathcfg commands.(SCGCQ02079595 port of SCGCQ02018134) 
 - Multiple status messages are displayed in the output	(SCGCQ02086536 port of SCGCQ02073042) 
 - Storcli throws different error messages for show status command in Ventura and Aero(SCGCQ02086689 port of SCGCQ02078409) 
 - Improve Debuggablity for MegaRAID Windows Driver by Adding RT Trace - new modifications(SCGCQ01825986 port of SCGCQ01824570) 
 - Turn on the boodrive by storcli, HII does not reflect it, still shows "Off"(SCGCQ01832791 port of SCGCQ01816927) 
 - Add interface in storecli that could get relearn complete status	(SCGCQ01850373 port of SCGCQ01848387) 
 - MR_7.10_Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/ eall/sall show all"(SCGCQ02050481 port of SCGCQ02018327) 
 - "Delete snapdump" command shows same description "Snapdump clear" for success and failure case.(SCGCQ02075284 port of SCGCQ02065734) 
 - Incorrect status displayed for resume copyback command.(SCGCQ02075291 port of SCGCQ02062834) 
 - Libmods: show.set lane speed shows success with wrong data when we are in SAS profile(SCGCQ02079506 port of SCGCQ02078513) 
 - Empty data is listed when we query for show linkconfig(SCGCQ02079511 port of SCGCQ02076931) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-patrolread-schema.json" and "/call pause patrolread"	(SCGCQ02079597 port of SCGCQ02035437) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for /cx/ px commands.(SCGCQ02079604 port of SCGCQ02018137) 
 - Aero - LibMod changes for ER SCGCQ01813156 : Addition of Aero and Sea device id's and checkwords	(SCGCQ01853418 port of SCGCQ01813626) 
 - Storcli throws an 'Incomplete foreign configuration' error when there is no enclosure connected(SCGCQ02007109 port of SCGCQ02006450) 
 - Extend major downgrade support in storCLI for SAS3 IT product(SCGCQ02032581 port of SCGCQ02029410) 
 - FW flash fails to load the latest image after upgrade downgrade with resetnow option	(SCGCQ02046879 port of SCGCQ02035152) 
 - MR_7.10_Storcli: Instance Validation Failed between "cache-vault-detailed-schema.json" and "/call/cv show all "(SCGCQ02050460 port of SCGCQ02019729) 
 - Storcli:"resource already in use" error message displayed when trying to create VD with one UG and one UBUnsp.(SCGCQ02075289 port of SCGCQ02064828) 
 - spell mistake in start diag operation failure(SCGCQ02079529 port of SCGCQ01998330) 
 - MR_7.9: Storcli reported unknown OS for Windows 10 RS5 LTSC.(SCGCQ02079601 port of SCGCQ01992461) 
 - Port information is not displayed for Vses Backplane	(SCGCQ02085875 port of SCGCQ02053070) 
 - Storcli: Force is mentioned as optional in snapdump delete command.(SCGCQ02086544 port of SCGCQ02083822) 
 - Add get VPD command support to StorCLI in OS environment	(SCGCQ01855067 port of SCGCQ01852603) 
 - Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01977760 port of SCGCQ01948579) 
 - CSET: Checking in Libmod changes for defect SCGCQ02030652 - (SCGCQ02045948(SCGCQ02047884 port of ) 
 - remove the maxconcurrentpd check from storcli and report fw returned failure	(SCGCQ02053931 port of SCGCQ02053910) 
 - Incorrect error message displayed while creating R10 VD when no free space available.(SCGCQ02075283 port of SCGCQ02067575) 
 - MR_7.10_Storcli: No schema file for controller unmap commands.(SCGCQ02079593 port of SCGCQ02016749) 
 - MR_7.10_Storcli: controller-detailed-properties-schema.json or "/call show all " output not in JSON format(SCGCQ02079610 port of SCGCQ02016771) 
 - Storcli connector display not matching with Aero board 9560-16i.(SCGCQ02085681 port of SCGCQ02072448)

EnhancementRequest:
- Updating ncurses library from 6.0 to 6.1(SCGCQ01836749) 
 - Command processor changes for Secure boot properties feature - SCGCQ01855473	(SCGCQ01855503) 
 - Adding secure boot properties to unified StorCLI	(SCGCQ01855473) 
 - Adding new MFI STAT - MFI_STAT_SECURE_BOOT_KEY_SLOTS_FULL 007.0711.0000.0000 for Lenovo(SCGCQ01865190) 

007.0713.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------
 - Storcli returns error for show file commands when parsing MR images eventhough the command was successful(SCGCQ01529009) 
 - "Cached Virtual Drives" displayed in /c0/dall show cachecade without the table.(SCGCQ01537017) 
 - storcli /c0 set sasaddhi =xxxx sasaddlow =xxxx displays incomplete sasaddress(SCGCQ01540807) 
 - storcli controller show all lists EPD's in VD list(SCGCQ01556595) 
 - controller show all command is not listing the Battery information(SCGCQ01561689) 
 - Commands "/call/all" return inappropriate message or segfault when both MR and IT controllers are connected(SCGCQ01561703) 
 - Instance Validation Failed between "vd-operations-migrate-schema.json" and "start migrate" JSON output.(SCGCQ01571207) 
 - Storcli: drive-group-security-schema.json is not present in the JSON Schema folder(SCGCQ01571280) 
 - Storcli: Instance Validation Failed between "drive_group_mirror_schema.json" and "/call/dall add mirror src=0" JSON output.(SCGCQ01571298) 
 - Instance Validation Failed "foreign-configuration-detailed-schema.json" and "/call/fall import preview" JSON output(SCGCQ01571393) 
 - "drive-power-on-schema.json" is named as "drive-get-power-on-schema.json" in "Schema_mapping_list" file.(SCGCQ01573229) 
 - Get VPD from MPB region is failure, but overalll status shows success(SCGCQ01589618) 
 - BBU-show-schema is not present in the schema mapping list, the list needs to be sorted to remove duplicate commands.(SCGCQ01599473) 
 - Coverity defect fixes for Uninitialized Variables, resource leaks(SCGCQ01600257) 
 - Spell mistake in error message for hwdev command(SCGCQ01614972) 
 - Coverity defect fix for itctflash file(SCGCQ01616369) 
 - Fixing coverity issues - Resource leaks - Part 5(SCGCQ01627961) 
 - Fixing coverity issues - Non array deletes - Part 6(SCGCQ01629478) 
 - CLI help does not reflect the new command to create an ePD(SCGCQ01639583) 
 - ModeE drive fw download not working when drive image is more than 32K(SCGCQ01681086) 
 - Space need in the output for Deprecated command in storclif64.exe when legacy Cli command is used(SCGCQ01687653) 
 - Grammatical mistakes in Perccli Un-supported RAID level warning message.(SCGCQ01714033) 
 - storclif /c0 start diag type=0, gives syntax error(SCGCQ01714663) 
 - Correcting the grammatical errors in firmware's MFI Stat messages(SCGCQ01717315) 
 - Unified StorCLI 7.7 : Unconfigured BAD drives are not displayed in /c0 show output(SCGCQ01718269) 
 - MR 7.7 - Storcli throws an incorrect error msg while importing foreign config from Raid to JBOD mode.(SCGCQ01718981) 
 - Unmap property is not displayed for a drive in drive show all command output(SCGCQ01720959) 
 - Unified StorCLI 7.7 : StorCLI should allow noreset option when current NVDATA is lesser than the new NVDATA for SAS3.5 IT(SCGCQ01727159) 
 - Enclosure show status command gives success but nothing is shown(SCGCQ01731280) 
 - Unified StorCLI 7.7 : StorCLI doesn't report failure status when nopad image flashing fails via completeflash command in MR(SCGCQ01749849) 
 - Help content for jbodx show unmap is not present(SCGCQ01790130) 
 - One of the requirement for Criteo is to display JBOD-WB (EPD) to OS drive mapping.(SCGCQ01804763) 
 - Turn on the boodrive by storcli, HII does not reflect it, still shows "Off"(SCGCQ01816927) 
 - Incorrect Interface Details for "storcli /c0 show" command(SCGCQ01837612) 
 - MR API - Incorrect value used for MR_DCMD_CTRL_SNAPDUMP_ONDEMAND(SCGCQ01882581) 
 - storclio command not working to update FW on SATA disk(SCGCQ01918814) 
 - Storcli- Delay seen in /c0 /vall show all o/p(SCGCQ01935697) 
 - Phase3 Beta PCIe: Loading SLOOB fails with error message "ExitLib failed for SAS IT Controller!! rval 0x801A"(SCGCQ01292964) 
 - storcli /cx/pall show command fails with older generation cards that does not support PCIe pages(SCGCQ01520816) 
 - Storcli: vd-delete-schema.json is not present in the JSON Schema folder(SCGCQ01571254) 
 - Instance Validation Failed between "controller-properties-schema.json" and "/call show" JSON output.(SCGCQ01573076) 
 - Unified LibMods : Fixing coverity issues - Resource leaks and Uninitialized variables - Part 2(SCGCQ01600381) 
 - Unified LibMods : Coverity fixes for uninitialized variables in File functions - Part 4(SCGCQ01606830) 
 - Checking in VBAS compliation changes(SCGCQ01630324) 
 - PERCCLI ePD personality behavior command is still an available option and has not been removed(SCGCQ01639798) 
 - Instance Validation Failed "system-schema.json" and "storcli64.exe show all" JSON output.(SCGCQ01640825) 
 - Storcli: VD creation fails from storcli in presence of 0KB bad drive .(SCGCQ01713240) 
 - Space need in the output for secure erase(SCGCQ01713604) 
 - PA2-MR7.7-StorCLI: "storcli /c0/v239 start migrate type=raid0 option=add drives=66:18" gives syntax error(SCGCQ01713681) 
 - Drive Listing Is Not In Order for "/c0 show" & "/c0/eall/sall show"(SCGCQ01714356) 
 - StorCLI 7.702 help for SnapDump is not clear(SCGCQ01715025) 
 - IT Fw Download command StorCLI /c0/eall/sall hang(SCGCQ01723226) 
 - Unified StorCLI Phase 8 : No help section for ForceHCB option(SCGCQ01731292) 
 - Unified CLI 7.7 : Fixing coverity issues - Resource leaks,Unused variables,and non-array deletes - Part 1(SCGCQ01732959) 
 - Unified StorCLI Phase 8 : Firmware downgrade should be supported only by StorCLIO for SAS3 IT controllers(SCGCQ01734559) 
 - Storcli does not display the complete enclosure serial number(SCGCQ01735493) 
 - Storcli vib update fails across releases.(SCGCQ01761795) 
 - StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers(SCGCQ01775602) 
 - StorCLI enable/disable unmap VDs return status as failed instead of successful(SCGCQ01803306) 
 - Removing the set/show of unmap on JBOD.(SCGCQ01817855) 
 - Unified StorCLI 7.6 : Read SBR fails with pre-ventura controllers(SCGCQ01539360) 
 - Storcli: Instance Validation Failed between "drive-group-detailed-schema.json" and "/call/dall show all" JSON output.(SCGCQ01571287) 
 - Instance Validation Failed between "foreign-configuration-schema.json" and "/call/fall show" JSON output.(SCGCQ01571391) 
 - Instance Validation Failed between "controller-detailed-properties-schema.json" and "/call show all" JSON output.(SCGCQ01573096) 
 - "drive-security-key-schema.json" is named as "drive-securitykey-schema.json" in "Schema_mapping_list" file.(SCGCQ01573226) 
 - CLI does not report Serial number for Enclosure.(SCGCQ01595640) 
 - Json schema for enclosure phyerrorcounters has not been added, output format needs modification.(SCGCQ01595673) 
 - Unified StorCLI 7.7 : SAS Phyloopback test reports false positive results(SCGCQ01624063) 
 - Update help contents for jbod delete(SCGCQ01624605) 
 - Drive download commands help syntax to be updated for IT.(SCGCQ01681089) 
 - Grammatical error in Perccli warning message during FW Flash.(SCGCQ01686670) 
 - Missing punctuation in Perccli delete config message(SCGCQ01698226) 
 - Personality Behavior Modes:Command returns failure when setting non-RAID behavior modes.(SCGCQ01713265) 
 - Unified StorCLI Phase 8 : NVMe and SAS Drive's WWN is incorrect for IT Controller(SCGCQ01749795) 
 - Storcli is not showing foreign configs if user has SED drive which is in foreign(SCGCQ01937410) 
 - controller show wbsupport reason is not listed in the cli output(SCGCQ01561704) 
 - Application crashes while executing storcli64.exe /c0/dall set hidden=on(SCGCQ01571256) 
 - Instance Validation Failed between "system-schema.json" and "show all" JSON output.(SCGCQ01571961) 
 - Unified StorCLI 7.7 : Coverity issues - Resource leaks,Uninitialized variables,and dead code - Part 1(SCGCQ01600195) 
 - Drive Fw download Coverity fixes(SCGCQ01615074) 
 - Unified StorCLI 7.7 : StorCLI should not issue SL_SET_LIB_PARAMETERS command(SCGCQ01676983) 
 - Detailed status is not displayed on locating a drive which is not connected to IT card.(SCGCQ01571154) 
 - Coverity defect fixes for Memory Leak, Uninitialized pointers(SCGCQ01605182) 
 - storclio need to support proprietary i2c controller mode.(SCGCQ01732990) 
 - MR7.7 LSA 4.180.0 enclosure type is not matched with storcli(SCGCQ01747333) 
 - Coverity libmods issues - Resource leaks and Wrong sizes(SCGCQ01600208) 
 - Unified StorCLI 7.7 : MegaCLI commands report command status code in UEFI environment(SCGCQ01624506) 
 - storcli did not show current profile when connection in invalid config.(SCGCQ01713676) 
 - Unmap support mfc bit and fde type mixing fields needs to be updated when extracting factory settings and also while modifying factory settings(SCGCQ01640217) 	
 - non-RAID:HII:CLI:Dedicated Hot Spare creation displays incorrect disk group association.(SCGCQ01698272) 
 - DHS:Unable to add dedicated Hot Spare drive to specified DG.(SCGCQ01714443) 
 - WWN for NVME PDs is reported as NA with MR(SCGCQ01731279) 
 - Updating the Diag results as per new API changes(SCGCQ01537255) 
 - Resource leaks,Uninitialized variables(SCGCQ01600311) 
 - Unified CLI : Coverity fixes for Uninitialized variables,resource leaks,and dead code handling - Part 3(SCGCQ01606785) 
 - Unified StorCLI 7.7 - Fixing coverity issues Resource leaks,Non-array deletes - Part 2(SCGCQ01757433) 
 - Storcli: UEFI shell error display-Error: Unsupported File open Mode.(SCGCQ01837752) 
 - Removal of ncurses references for linux makefile(SCGCQ01955544) 
  - Changing ini file name to storelibconfit.ini(SCGCQ01275669 port of SCGCQ01275496) 
 - Changing ini file name to storelibconfit.ini(SCGCQ01275670 port of SCGCQ01275496) 
 - Enumeration of drives in NGM[PERCCLI Implementation / HBA330 Mini Mezz](SCGCQ01529059 port of SCGCQ01458174) 
 - Storcli PR help execution delay is missing when PR running continuously(SCGCQ01537219 port of SCGCQ01534552) 
 - Handle memory leaks in getSortedPdList(SCGCQ01571890 port of SCGCQ01283497) 
 - Disk sorting based on connector name, slot and position(SCGCQ01571926 port of SCGCQ01307257) 
 - Collecting snapdump through StorCli(SCGCQ01594186 port of SCGCQ01581899) 
 - Unified StorCLI 7.6 : Creation of VD aborts StorCLI when FW returns error code for MR_DCMD_CFG_READ DCMD(SCGCQ01595361 port of SCGCQ01588245) 
 - Allow "noreset" option for IT controllers during firmware download(SCGCQ01599545 port of SCGCQ01514483) 
 - Enumeration of drives in NGM[PERCCLI Implementation / HBA330 Mini Mezz](SCGCQ01600137 port of SCGCQ01458174) 
 - StorCLI should not display SED property when using IT-HBA(SCGCQ01600142 port of SCGCQ01589445) 
 - Cutlass Phase 16 Storcli: Partner device ID should be suppressed under ./storcli /c0/eall show for multipath connections(SCGCQ01619201 port of SCGCQ01606780) 
 - Storcli should not create a snapdump image if there is no valid image(SCGCQ01624677 port of SCGCQ01623883) 
 - Removing readonly properties from for snapdump in storcli.(SCGCQ01669986 port of SCGCQ01669570) 
 - Different RetCode for N/A Drives - Parallel Drive Update(SCGCQ01682236 port of SCGCQ01681478) 
 - Storcli: VD creation fails from storcli in presence of 0KB bad drive .(SCGCQ01713567 port of SCGCQ01713240) 
 - Flashing PD's with parallel option wrong status is given by Storcli(SCGCQ01714667 port of SCGCQ01713734) 
 - Missing punctuation in Perccli delete config message(SCGCQ01714668 port of SCGCQ01698226) 
 - When a bad PD is flashed it fails as expected but error code is wrong(SCGCQ01714670 port of SCGCQ01713728) 
 - Parallel drive fw update on 1st drive fails, while drive fW update on another drive is in progress(SCGCQ01714671 port of SCGCQ01676426) 
 - Enclosure show status command gives success but nothing is shown(SCGCQ01731381 port of SCGCQ01731280) 
 - storclio need to support proprietary i2c controller mode.(SCGCQ01801679 port of SCGCQ01732990) 
 - Phase 7 - Drive Listing Is Not In Order for "/c0 show" & "/c0 show all"(SCGCQ01810054 port of SCGCQ01809355) 
 - EPD-PT behavior changes for Aero to support in RAID personality(SCGCQ01816139 port of SCGCQ01594176) 
 - perccli /cx delete config command getting incorrect error message.(SCGCQ01851908 port of SCGCQ01850719) 
 - State of the tape drive should be displayed as "JBOD" when FW state is MR_PD_STATE_SYSTEM(SCGCQ01853457 port of SCGCQ01853444) 
 - StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911830 port of SCGCQ01886637) 
 - (Libmods) Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder)(SCGCQ01915314 port of SCGCQ01227144) 
 - Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder(SCGCQ01915320 port of SCGCQ01222855) 
 - Updating ncurses library from 6.0 to 6.1(SCGCQ01915841 port of SCGCQ01836749) 
 - Disk performance throttled when running MegaCli AdpEvent log dump on Aspen and Vail (Invader and Intruder(SCGCQ01921533 port of SCGCQ01220901) 
 - Libmod changes: Adding CLI command to display/toggle new controller property.(SCGCQ01106982(SCGCQ01922038 port of SCGCQ01106988) 
 - LibMods : Adding the function that changing flag of full initialize completion(SCGCQ01922843 port of SCGCQ01141462) 
 - MFI Frame alignment(SCGCQ01922846 port of SCGCQ01064480) 
 - Square bracket is missing in the syntax of "set hardware device page" in storclio.(SCGCQ01929787 port of SCGCQ01224857) 
 - Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01526330 port of SCGCQ01274709) 
 - Change in RAID levels displaying in controller show all command(SCGCQ01540785 port of SCGCQ01509578) 
 - Ctrl-H hang during foreign import along with app tab toggling.(SCGCQ01571937 port of SCGCQ01356240) 
 - Data Abort Exception while entering CTRL R(SCGCQ01571939 port of SCGCQ01380831) 
 - Storcli_Aero: Storcli not able to detect controller at EFI shell without Avago MR driver.(SCGCQ01599436 port of SCGCQ01595698) 
 - This feature is not supported on this Controller" is displayed multiple times.(SCGCQ01599461 port of SCGCQ01595717) 
 - Unified StorCLI 7.6 : Creation of VD aborts StorCLI when FW returns error code for MR_DCMD_CFG_READ DCMD(SCGCQ01600150 port of SCGCQ01588245) 
 - Snapdump file user does not know the compression method(SCGCQ01624670 port of SCGCQ01616917) 
 - Storcli_Aero: unable to set sasadd methodport on IT controller.(SCGCQ01628097 port of SCGCQ01609234) 
 - Patrol read state shown as aborted while it actually is paused.(SCGCQ01714666 port of SCGCQ01714264) 
 - Storcli output does not list missing PD's(SCGCQ01715372 port of SCGCQ01715114) 
 - Grammatical mistakes in Perccli Un-supported RAID level warning message.(SCGCQ01720760 port of SCGCQ01714033) 
 - Unified StorCLI Phase 8 : NVMe and SAS Drive's WWN is incorrect for IT Controller(SCGCQ01749927 port of SCGCQ01749795) 
 - storcli /cx/pall show command fails with older generation cards that does not support PCIe pages(SCGCQ01758163 port of SCGCQ01520816) 
 - PERC10.2:CLI:Help: Grammatical Error in Text String "/ex - specifies a enclosure where X is the enclosure device ID."(SCGCQ01768428 port of SCGCQ01764888) 
 - "storcli show snapdump" output is incorrect(SCGCQ01817308 port of SCGCQ01817307) 
 - StorCLI should support firmware flash for SAS3 IR Controllers(SCGCQ01873578 port of SCGCQ01835627) 
 - show enclosure command is not exiting to shell(SCGCQ01874899 port of SCGCQ01814011) 
 - Storcli issuing 'add jbod drives=all' causes storcli to crash(SCGCQ01893370 port of SCGCQ01892288) 
 - Hide/Unhide command output display incorrect VD no for VDs on which the operation is not supported(SCGCQ01911848 port of SCGCQ01837932) 
 - Turn on the boodrive by storcli, HII does not reflect it, still shows "Off"(SCGCQ01915791 port of SCGCQ01816927) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ01917007 port of SCGCQ01761309) 
 - PH9 PA StorCLI - /c0/eall/sal show all gives success message when no drives connected(SCGCQ01917168 port of SCGCQ01855721) 
 - Storcli: Ventura B0: BIOS Flashing Failure Observed in EFI Storcli and Multiple Tries Causes UART Unresponsive(SCGCQ01917338 port of SCGCQ01829667) 
 - Adding CLI command to display/toggle new controller property.(SCGCQ01922836 port of SCGCQ01106982) 
 - Storcli not working on large config setup when some of the drives are missing or the system has foreign config.(SCGCQ01940851 port of SCGCQ01940805) 
 - Expander FW download using storecli utility crashs.(SCGCQ01979615 port of SCGCQ01979599) 
 - Updating readme file(SCGCQ01294583 port of SCGCQ01294570) 
 - Remove sorting logic for array physical drives(SCGCQ01445612 port of SCGCQ01444666) 
 - Add /dev/sdX to StorCLI output(SCGCQ01514530 port of SCGCQ01505055) 
 - Allow "noreset" option for IT controllers during firmware download(SCGCQ01517643 port of SCGCQ01514483) 
 - Libmod: checking-in the changes forLibmods for SCGCQ01525764(SCGCQ01528935 port of SCGCQ01528886) 
 - Libmod: checking-in the changes forLibmods for SCGCQ01525764(SCGCQ01528936 port of SCGCQ01528886) 
 - Implemented to display the full Model number of the SATA drive when connected to an IT controller.(SCGCQ01528939 port of SCGCQ01525764) 
 - Unified StorCLI 7.6 : Read SBR fails with pre-ventura controllers(SCGCQ01539390 port of SCGCQ01539360) 
 - Removal of MegaCLI syntax from StorCLI(SCGCQ01591157 port of SCGCQ01504604) 
 - Unified LibMod changes for ER : SCGCQ01504604 - Removal of MegaCLI syntax from StorCLI(SCGCQ01591158 port of SCGCQ01504610) 
 - Spell error in /call/dall split mirror output.(SCGCQ01599464 port of SCGCQ01595709) 
 - storcli controller show all lists EPD's in VD list(SCGCQ01599486 port of SCGCQ01556595) 
 - Detailed status is not displayed on locating a drive which is not connected to IT card.(SCGCQ01599519 port of SCGCQ01571154) 
 - Storcli returns error for show file commands when parsing MR images eventhough the command was successful(SCGCQ01600149 port of SCGCQ01529009) 
 - Storcli_Aero: Storcli not able to detect controller at EFI shell without Avago MR driver.(SCGCQ01600151 port of SCGCQ01595698) 
 - Support only Dell SAS IT Controllers with PERCCLI(SCGCQ01618493 port of SCGCQ01547929) 
 - Cutlass Phase 16 Storcli: Partner device ID should be suppressed under ./storcli /c0/eall show for multipath connections(SCGCQ01625114 port of SCGCQ01606780) 
 - Cached IO policy(SCGCQ01627941 port of SCGCQ01607434) 
 - Space need in the output for secure erase(SCGCQ01714669 port of SCGCQ01713604) 
 - Unified StorCLI 7.7 : Unconfigured BAD drives are not displayed in /c0 show output(SCGCQ01718294 port of SCGCQ01718269) 
 - Unified StorCLI 7.7 : StorCLI doesn't report failure status when nopad image flashing fails via completeflash command in MR(SCGCQ01749921 port of SCGCQ01749849) 
 - storcli did not show current profile when connection in invalid config.(SCGCQ01760598 port of SCGCQ01713676) 
 - non-RAID:HII:CLI:Dedicated Hot Spare creation displays incorrect disk group association.(SCGCQ01760604 port of SCGCQ01698272) 
 - Storcli does not display the complete enclosure serial number(SCGCQ01760655 port of SCGCQ01735493) 
 - "storcli show snapdump" output is incorrect(SCGCQ01817270 port of SCGCQ01804779) 
 - Fails to set user defined value for delayOCR field in the SnampDump(SCGCQ01817941 port of SCGCQ01817465) 
 - Fails to set SnapDump savecount.(SCGCQ01817942 port of SCGCQ01817177) 
 - displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state"(SCGCQ01836905 port of SCGCQ01681538) 
 - Error message when Maximum number of VDs are reached(SCGCQ01911765 port of SCGCQ01856544) 
 - perccli /cx delete config command getting incorrect error message.(SCGCQ01911827 port of SCGCQ01850719) 
 - Unified LibMod changes : Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01913460 port of SCGCQ01893074) 
 - Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01913461 port of SCGCQ01892560) 
 - Add interface in storecli that could get relearn complete status(SCGCQ01914835 port of SCGCQ01848387) 
 - 6.13_SDS : Wrong error message is displayed on trying to create R0 vd on an pre configured drive as EPD.(SCGCQ01922844 port of SCGCQ01196785) 
 - Added new commands from StorCLI(SCGCQ01922845 port of SCGCQ01134166) 
 - Unified StorCLI : Enclosure devices are part of drive list used for drive operations(SCGCQ01979534 port of SCGCQ01979483) 
 - Add /dev/sdX to StorCLI output(SCGCQ01514531 port of SCGCQ01514516) 
 - Prepare To Transport(SCGCQ01568934 port of SCGCQ00936041) 
 - CacheCade VD association returns error in Config Utility (Ctrl-R(SCGCQ01571889 port of SCGCQ01264552) 
 - .(SCGCQ01571935 port of SCGCQ01325052) 
 - Commands "/call/all" return inappropriate message or segfault when both MR and IT controllers are connected(SCGCQ01599483 port of SCGCQ01561703) 
 - Un-supported command displayed for "storcli64.exe /call show sasaddress"(SCGCQ01620412 port of SCGCQ01619562) 
 - Update help contents for jbod delete(SCGCQ01625945 port of SCGCQ01624605) 
 - Storcli_Aero: unable to set sasadd methodport on IT controller.(SCGCQ01628094 port of SCGCQ01609234) 
 - Libmod Changes for Defect SCGCQ01595640 (CLI does not report Serial number for Lenovo D1224 Enclosure(SCGCQ01714307 port of SCGCQ01664412) 
 - Drive Listing Is Not In Order for "/c0 show" & "/c0/eall/sall show"(SCGCQ01732928 port of SCGCQ01714356) 
 - controller show wbsupport reason is not listed in the cli output(SCGCQ01760590 port of SCGCQ01561704) 
 - Storcli does not display the complete enclosure serial number(SCGCQ01760636 port of SCGCQ01735493) 
 - "Cached Virtual Drives" displayed in /c0/dall show cachecade without the table.(SCGCQ01760676 port of SCGCQ01537017) 
 - Trying to import Secured LDs and if wrong Security Key is mentioned, Error is referring to "Pass phrase"(SCGCQ01764539 port of SCGCQ01763866) 
 - Libmods: SCGCQ01760508 Error message-"Reached Maximum Supported virtual Disks" is displayed when no free space left create VD.(SCGCQ01764540 port of SCGCQ01764049) 
 - Enhance the detailed help for Firmware download and get bios command.(SCGCQ01792109 port of SCGCQ01790167) 
 - Updating ncurses library from 6.0 to 6.1(SCGCQ01837234 port of SCGCQ01836749) 
 - Add get VPD command support to StorCLI in OS environment(SCGCQ01911298 port of SCGCQ01852603) 
 - perccli(007.0523.0000.0000 Jul 20, 2018(SCGCQ01914827 port of SCGCQ01874120) 
 - Incorrect Interface Details for "storcli /c0 show" command(SCGCQ01915785 port of SCGCQ01837612) 
 - Invader/Intruder: MR 6.13.1- PD FW download status help to be updated(SCGCQ01922838 port of SCGCQ01256727) 
 - Change in RAID levels displaying in controller show all command(SCGCQ01511611 port of SCGCQ01509578) 
 - Implemented to display the full Model number of the SATA drive when connected to an IT controller.(SCGCQ01528940 port of SCGCQ01525764) 
 - Storcli PR help execution delay is missing when PR running continuously(SCGCQ01537216 port of SCGCQ01534552) 
 - Application crashes while executing storcli64.exe /c0/dall set hidden=on(SCGCQ01599467 port of SCGCQ01571256) 
 - Un-supported command displayed for "storcli64.exe /call show sasaddress"(SCGCQ01620417 port of SCGCQ01619562) 
 - syntax error while executing "storcli64.exe /c0 get firmware ? "(SCGCQ01620453 port of SCGCQ01618675) 
 - Storcli does not display the complete enclosure serial number(SCGCQ01760661 port of SCGCQ01735493) 
 - PH9 PA StorCLI - Tape drive entry not seen at "Requested boot drive" field after set bootdrive on(SCGCQ01853459 port of SCGCQ01850418) 
 - Unified StorCLI : StorCLI doesn't display OS Name for Windows Server 2019 server(SCGCQ01869194 port of SCGCQ01867354) 
 - StorCLI should not display SED property when using IT-HBA(SCGCQ01915857 port of SCGCQ01589445) 
 - Unified StorCLI Phase 9: Prints are seen in the console when SL_GET_CTRL_INFO fails from SL in uEFI platform(SCGCQ01917167 port of SCGCQ01866548) 
 - Unconfigured Good PD is showing as belonging to Disk Group 0.(SCGCQ01525771 port of SCGCQ01520567) 
 - Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01526326 port of SCGCQ01526321) 
 - This feature is not supported on this Controller" is displayed multiple times.(SCGCQ01599446 port of SCGCQ01595717) 
 - Incremented devicename is programmed for all the phy's in IT controller(SCGCQ01599449 port of SCGCQ01548481) 
 - controller show all command is not listing the Battery information(SCGCQ01599459 port of SCGCQ01561689) 
 - Support only Dell SAS IT Controllers with PERCCLI(SCGCQ01618501 port of SCGCQ01547929) 
 - syntax error while executing "storcli64.exe /c0 get firmware ? "(SCGCQ01620437 port of SCGCQ01618675) 
 - Invalid return status from Storcli(SCGCQ01731842 port of SCGCQ01731797) 
 - Unified StorCLI LibMods 7.6 - Moving CLI's VIB toolchain to 6.0 and workbench to 3.5.7(SCGCQ01749416 port of SCGCQ01720952) 
 - DHS:Unable to add dedicated Hot Spare drive to specified DG.(SCGCQ01760603 port of SCGCQ01714443) 
 - Add Downgrade Firmware function in Storcli(SCGCQ01813396 port of SCGCQ01583223) 
 - Libmod changes for StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers - SCGCQ01775602(SCGCQ01853371 port of SCGCQ01775616) 
 - Unified StorCLI : StorCLI doesn't display OS Name for Windows Server 2019 server(SCGCQ01916018 port of SCGCQ01867354) 
 - Unconfigured Good PD is showing as belonging to Disk Group 0.(SCGCQ01525774 port of SCGCQ01520567) 
 - Spell error in /call/dall split mirror output.(SCGCQ01599466 port of SCGCQ01595709) 
 - Get VPD from MPB region is failure, but overalll status shows success(SCGCQ01599481 port of SCGCQ01589618) 
 - Compilation errors while compiling parser module(SCGCQ01600565 port of SCGCQ01600563) 
 - CLI does not report Serial number for Enclosure.(SCGCQ01714296 port of SCGCQ01595640) 
 - Unified StorCLI 7.6 - Moving CLI's VIB toolchain to 6.0 and workbench to 3.5.7(SCGCQ01745530 port of SCGCQ01720947) 
 - Updating the Diag results as per new API changes(SCGCQ01537265 port of SCGCQ01537255) 
 - Collecting snapdump through StorCli (Libmods(SCGCQ01594187 port of SCGCQ01589854) 
 - WWN for NVME PDs is reported as NA with MR(SCGCQ01749397 port of SCGCQ01731279) 
 - Unified StorCLI 7.7 : StorCLI should not issue SL_SET_LIB_PARAMETERS command(SCGCQ01758162 port of SCGCQ01676983) 
 - Spell mistake in error message for hwdev command(SCGCQ01760594 port of SCGCQ01614972) 
 - Error message-"Reached Maximum Supported virtual Disks" is displayed when no free space left create VD.(SCGCQ01764538 port of SCGCQ01760508) 
 - PERCCLI_PERC10.2-007.0512/When selecting a PD that is not configurable, it is showing "Atleast" which should be "At least"(SCGCQ01768422 port of SCGCQ01764929) 
 - StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers(SCGCQ01853405 port of SCGCQ01775602) 
 - Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01977760 port of SCGCQ01948579) 
 
EnhancementRequests
 - Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01473897) 
 - Adding JSON schema for Virtual Drive level commands(SCGCQ01516772) 
 - Enhance StorCLI show file= to include PnP ID(SCGCQ01517431) 
 - Need Storcli support drive FW upgrade(SCGCQ01583217) 
 - displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state"(SCGCQ01681538) 
 - Add ForceHCB option in StorCLI for IT controllers(SCGCQ01718946) 
 - Switch attached NVMe HW RAID support for Supermicro backplanes(SCGCQ01720819) 
 - Added customer serial number field to MFC Manufacturing 2 structure(SCGCQ01873417) 
 - MR API changes to support EKMS over OOB(SCGCQ01874035) 
 - Add new error code for tampered or invalid controller(SCGCQ01885686) 
 - Interrupt coalsecing setting per group of 8 replies queues (h/w VF registers(SCGCQ01886424) 
 - [MR 7.8] API change to export "disable least latency mode"(SCGCQ01887495) 
 - HDET: Support smp passthrough storeliboob (API changes requirement(SCGCQ01916035) 
 - Add secure boot key update complete event(SCGCQ01928254) 
 - Add Board Support Package Image Type to MR_IMAGE_TYPE(SCGCQ01931637) 
 - Support dynamically add/remove controller in Storelib IT for MCTP over PCIe(SCGCQ01934815) 
 - Fix MR_CTRL_INFO to support backward compatibility(SCGCQ01946548) 
 - Add a new log event used whenever the snap dump properties are modified.(SCGCQ01963328) 
 - Add a bit for atomic descriptor capable(SCGCQ01965047) 
 - Add Downgrade Firmware function in Storcli(SCGCQ01583223) 
 - Add support for TCG Opal 2.0 compliant SAS/SATA HDDs, SAS/SATA HDDs operations in StorCLI(SCGCQ01593849) 
 - StorCLI JSON 4.0 compliant schema creation for Phy (including mux and lane) level commands(SCGCQ01594119) 
 - Improve PERCcli Terminology When in eHBA Mode(SCGCQ01615487) 
 - UNMAP/TRIM/WRITESAME for NVMe devices for R0/1/EPD/JBOD(SCGCQ01727113) 
 - Adding JSON schema for Drive Group and Foreign configuration commands(SCGCQ01531269) 
 - Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01583226) 
 - Libmods : Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01615540) 
 - To add restriction on personality change requests from RAID to eHBA and eHBA to RAID(SCGCQ01721528) 
 - StorCLI JSON 4.0 compliant schema creation for Enclosure, BBU and CacheVault commands(SCGCQ01576130) 
 - Add get VPD command support to StorCLI in OS environment(SCGCQ01852603) 
 - Improve PERCcli Terminology When in eHBA Mode(SCGCQ01628424) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ01761309) 


007.0525.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------

Defects (16)
-.(SCGCQ01753405)
- Grammatical mistakes in Perccli Un-supported RAID level warning message.(SCGCQ01714033)
- Correcting the grammatical errors in firmware's MFI Stat messages.(SCGCQ01717315)
- Enclosure show status command gives success but nothing is shown.(SCGCQ01731280)
- One of the requirement for Criteo is to display JBOD-WB (EPD) to OS drive mapping.(SCGCQ01804763)
- Turn on the boodrive by storcli, HII does not reflect it, still shows "Off".(SCGCQ01816927)
- Incorrect Interface Details for "storcli /c0 show" command.(SCGCQ01837612)
- Two MCTP error codes in slerrors.h show same offset code 0x7098.(SCGCQ01627548)
- Space need in the output for secure erase.(SCGCQ01713604)
- seg fault is seen when when we try to generate CRC errors using megamon.(SCGCQ01841619)
- Missing punctuation in Perccli delete config message.(SCGCQ01698226)
- Personality Behavior Modes:Command returns failure when setting non-RAID behavior modes.(SCGCQ01713265)
- non-RAID:HII:CLI:Dedicated Hot Spare creation displays incorrect disk group association.(SCGCQ01698272)
- DHS:Unable to add dedicated Hot Spare drive to specified DG.(SCGCQ01714443)
- WWN for NVME PDs is reported as NA with MR.(SCGCQ01731279)
- Storcli: UEFI shell error display-Error: Unsupported File open Mode.(SCGCQ01837752)
- perccli /cx delete config command getting incorrect error message.(SCGCQ01851908 port of SCGCQ01850719)
- storclio need to support proprietary i2c controller mode.(SCGCQ01801679 port of SCGCQ01732990)
- State of the tape drive should be displayed as "JBOD" when FW state is MR_PD_STATE_SYSTEM.(SCGCQ01853457 port of SCGCQ01853444)
- Phase 7 - Drive Listing Is Not In Order for "/c0 show" & "/c0 show all".(SCGCQ01810054 port of SCGCQ01809355)
- storcli /cx/pall show command fails with older generation cards that does not support PCIe pages.(SCGCQ01758163 port of SCGCQ01520816)
- Unified StorCLI Phase 8 : NVMe and SAS Drive's WWN is incorrect for IT Controller.(SCGCQ01749927 port of SCGCQ01749795)
- storcli did not show current profile when connection in invalid config.(SCGCQ01760598 port of SCGCQ01713676)
- Storcli does not display the complete enclosure serial number.(SCGCQ01760655 port of SCGCQ01735493)
- Unified StorCLI 7.7 : StorCLI doesn't report failure status when nopad image flashing fails via completeflash command in MR.(SCGCQ01749921 port of SCGCQ01749849)
- Unified StorCLI 7.7 : Unconfigured BAD drives are not displayed in /c0 show output.(SCGCQ01718294 port of SCGCQ01718269)
- "Cached Virtual Drives" displayed in /c0/dall show cachecade without the table.(SCGCQ01760676 port of SCGCQ01537017)
- controller show wbsupport reason is not listed in the cli output.(SCGCQ01760590 port of SCGCQ01561704)
- Updating ncurses library from 6.0 to 6.1.(SCGCQ01837234 port of SCGCQ01836749)
- Drive Listing Is Not In Order for "/c0 show" & "/c0/eall/sall show".(SCGCQ01732928 port of SCGCQ01714356)
- Storcli does not display the complete enclosure serial number.(SCGCQ01760661 port of SCGCQ01735493)
- Unified StorCLI : StorCLI doesn't display OS Name for Windows Server 2019 server.(SCGCQ01869194 port of SCGCQ01867354)
- PH9 PA StorCLI - Tape drive entry not seen at "Requested boot drive" field after set bootdrive on.(SCGCQ01853459 port of SCGCQ01850418)
- Libmod changes for StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers - SCGCQ01775602.(SCGCQ01853371 port of SCGCQ01775616)
- Add Downgrade Firmware function in Storcli.(SCGCQ01813396 port of SCGCQ01583223)
- Spell mistake in error message for hwdev command.(SCGCQ01760594 port of SCGCQ01614972)
- StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers.(SCGCQ01853405 port of SCGCQ01775602)
- Unified StorCLI 7.7 : StorCLI should not issue SL_SET_LIB_PARAMETERS command.(SCGCQ01758162 port of SCGCQ01676983)

EnhancementRequests (30)
- API Changes for Driver/FW DCMD HandShake.(SCGCQ01841266)
- RTTrace Enable/Disable API changes.(SCGCQ01830211)
- Criteo: API changes reversal.(SCGCQ01760512)
- RTTrace API Changes.(SCGCQ01745568)
- API changes needed to support eHBA product series.(SCGCQ01727346)
- Create sanitize events.(SCGCQ01713708)
- MPI 2.5: Add MaxEnclosureLevel field to BIOS Page 1.(SCGCQ01570730)
-.(SCGCQ01593479)
-.(SCGCQ01761309)
- displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state".(SCGCQ01681538)
- API change for Switch attached NVMe HW RAID support for Supermicro backplanes.(SCGCQ01697667)
- Mixing Rules for SED and non-SED drives to create non-secure array with controller security enabled.(SCGCQ01757538)
- Unmap: Define new API for enhanced UNMAP support.(SCGCQ01758062)
- Adding API bit to indicate whether forced personality change is supported or not.(SCGCQ01762153)
- Unmap: Define new events for enhanced UNMAP support [MR7.8].(SCGCQ01803319)
- Deprecate the snap dump fields that are no longer needed for MR_SNAP_DUMP_PROPERTIES structure.(SCGCQ01816724)
-.(SCGCQ01818580)
- Add the API to clear all the snap-dumps from firmware.(SCGCQ01824135)
- API change to provide learn complete timestamp.(SCGCQ01845269)
- Added Support for Triggering SnapDump.(SCGCQ01848759)
- Add secure boot support.(SCGCQ01792416)
- Improve PERCcli Terminology When in eHBA Mode.(SCGCQ01615487)
- Including The Time Stamp for every Snap Dump created in the firmware.(SCGCQ01797424)
- Aero FW - Reporting SSD wear gauge values for OEM specific customers.(SCGCQ01798686)
- [MR 7.8] API change to return apt failure status for a personality change request.(SCGCQ01853480)
- Added new events for unmap policy changes.(SCGCQ01871912)
- MPI 2.5: Add OEMRD field to SAS Enclosure Page 0.(SCGCQ01553021)
- API Changes - After Vision PSOC FW update, applications should ask the user for power cycle instead of reboot.(SCGCQ01765150)
- To add restriction on personality change requests from RAID to eHBA and eHBA to RAID.(SCGCQ01721528)
- Add get VPD command support to StorCLI in OS environment.(SCGCQ01852603)


0007.0507.0000.0000-1 - Moderate Impact/Low Probability of Occurrence
-------------------

Defects (75)
- Profile Mgmt API Changes.( SCGCQ00883008)
- MR_RAID_CTX_G35 has one too many bits.(SCGCQ00886417)
- Reintroduce numSGEExt Field in Raid Context for Invader to support 1MB IO.(SCGCQ00927738)
- The code had events with repetitive ID and some structures clashing.(SCGCQ00948535)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23.(SCGCQ01001936)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23 has been added back again into adapteroperations 4.(SCGCQ01014835)
- 800C error when execting Get MFC default function.(SCGCQ01037840)
- Enable WB support via API.(SCGCQ01405242)
- Storcli: Instance Validation Failed between "controller-properties-schema.json" and "show" json..(SCGCQ01413239)
- Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON..(SCGCQ01423458)
- Port linkspeed is displayed in a different JSON object for NVMe drives.(SCGCQ01436920)
- Remove unsupported Ethernet code for IT controller from CLI.(SCGCQ01448979)
- Show command is not processed for IT firmware and IT complete flash images in big endian server.(SCGCQ01451940)
- storcli /c0/e123/s1 show poh shows drive info on IT controller.(SCGCQ01456171)
- Storcli displays "success" and "failure" both when trying to enable UNMAP on RAID5 using SSDs..(SCGCQ01462396)
- Storcli verbose help for Unmap has spelling mistakes.(SCGCQ01462401)
- Updating the JSON Schema for the SCSI Unmap feature.(SCGCQ01465745)
- Storcli: Instance Validation Failed between "system-schema.json" and "show" JSON..(SCGCQ01467131)
- Part 1 : Fixing coverity issues - Resource leaks and Illegal comparison.(SCGCQ01470420)
- Instance Validation Failed between "virtual-drive-config-schema.json" and "add vd " JSON.(SCGCQ01471852)
- Start/Stop locate on a invalid enclosure returns success.(SCGCQ01480910)
- Detailed help contents were not present for most of the IT download options..(SCGCQ01483760)
- Spelling errors in the "/cx restart" command..(SCGCQ01486415)
- Storcli: Instance Validation Failed between "controller-flash-component-erase-schema.json" and "flasherase" JSON..(SCGCQ01506022)
- Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show_profile" JSON..(SCGCQ01506052)
- CLI help does not reflect the new command to create an ePD.(SCGCQ01639583)
- Phase3 Beta PCIe: Loading SLOOB fails with error message "ExitLib failed for SAS IT Controller!! rval 0x801A".(SCGCQ01292964)
- Instance Validation is failing for mentioned commands..(SCGCQ01415355)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show all" JSON output..(SCGCQ01423447)
- Incorrect PNP ID format is displayed in EFI for firmware and complete flash images.(SCGCQ01448990)
- PH6 Ventura Pre-Alpha - StorCLI - "show file = fw.bin" command usage is not updated in help.(SCGCQ01460588)
- Showing empty error msg in CLI when Unmap not supported is returned by FW..(SCGCQ01464580)
- Storcli: Instance Validation Failed between "enclosure-schema.json" and "/call/eall show" JSON..(SCGCQ01467146)
- Storcli: Instance Validation Failed between "jbod-show-schema.json" and "/call/jbodall show" JSON..(SCGCQ01467694)
- PH6 Ventura Pre-Alpha - StorCLI - /c0 show all - Capabilities for supported drives seen only SAS/SATA, NVMe not found.(SCGCQ01480920)
- PH6 Ventura - Storcli crashed in Win2016 when "storcli64.exe J" is executed.(SCGCQ01488062)
- Instance Validation Failed between "controller-termlog-schema.json" and "set termlog=off" JSON..(SCGCQ01506041)
- Readme file have no mention of PD and JBOD level command support..(SCGCQ01507421)
- Checking in VBAS compliation changes.(SCGCQ01630324)
- PERCCLI ePD personality behavior command is still an available option and has not been removed.(SCGCQ01639798)
- Storcli: VD creation fails from storcli in presence of 0KB bad drive.(SCGCQ01713240)
- Operating system is not displaying the version in EFI for any of command in cli.(SCGCQ01410613)
- Instance Validation Failed between "controller-ASO-schema.json" and "show ASO" json.(SCGCQ01430237)
- Updating pre-ventura SBR fails with "hwdevice" command.(SCGCQ01438214)
- MR7.5: StorCLI reports Multipath ON during set but OFF during show commands.(SCGCQ01440234)
- Adding excludevd option to the help file of patrolread command.(SCGCQ01443435)
- PH6 Ventura Pre-Alpha - StorCLI - /cx/ set bootdrive = on/off command not updated in help page.(SCGCQ01460582)
- Schema addition for "show file=" command.(SCGCQ01461209)
- PH6 Ventura Pre-Alpha -- "storcli64.exe /c0 compare ssid ver = 2 J" command crashes and utility stopped working in Win2016.(SCGCQ01462593)
- MR 7.5_UNMAP : UNMAP support info is not shown in controller supported operations and VD properties.(SCGCQ01464562)
- PH6 Ventura StorCLI - Pre-Alpha - /cx compare detailed help is not giving complete information.(SCGCQ01464762)
- Instance Validation Failed between "controller-patrolread-set-schema.json" and "/c0 set pr excludevd=1" JSON.(SCGCQ01472845)
- Instance Validation Failed between "drive-operations-patrolread-schema.json" and "/call/e65/sall show patrolread".(SCGCQ01473344)
- Grammatical error in Perccli warning message during FW Flash.(SCGCQ01686670)
- OpROM's and their versions are not displayed for 8,32,and 64 MB IT complete flash images.(SCGCQ01449785)
- Part 3 : Fixing coverity issue : Resource leaks.(SCGCQ01472797)
- Storcli: Instance Validation Failed between schema and JSON output for many scenarios with one common error.(SCGCQ01506038)
- Reverting back SL_MAX_OS_DRIVE_COUNT value to 300.(SCGCQ01114306)
- Assign VDs suboption in cachecade VD creation is not assigning the intended VDs.(SCGCQ01419754)
- Incorrect help description for erase and download completeflash commands.(SCGCQ01470263)
- Instance Validation Failed between "controller-jbod-schema.json" and "add jbod" JSON..(SCGCQ01472802)
- Storcli: Instance Validation Failed for direct attached drive commands..(SCGCQ01472833)
- Check for supported pages for firing drive SCSI commands.(SCGCQ01474325)
- No error description when start/stop locate fails on the drive from StoreLIBIT library.(SCGCQ01480900)
- IT command to set sasadd and other set operations shows success for an MR controller.(SCGCQ01483753)
- Changing CV/BBU state algorithm according to the updated design document..(SCGCQ01388595)
- DriveID and errormsg are coming improper on drive POH command when failed.(SCGCQ01443683)
- Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" json..(SCGCQ01465446)
- Coverity libmods issues - Resource leaks and Wrong sizes.(SCGCQ01472195)
- Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/eall/sall show all" json..(SCGCQ01473334)
- Unified StorCLI does not support erasing of persistent config pages in host for IT controllers.(SCGCQ01466766)
- Storcli: Instance Validation Failed between "jbod-show-schema.json" and "/c0/jbodx show" JSON..(SCGCQ01472821)
- UEFI StorCLI should detect controller when UEFI driver is not present and when FW is in ready state.(SCGCQ01489472)
- The structure name is changed from oob_i2c to oob to avoid compilation failure in OOB SL.(SCGCQ01015024)
- Instance Validation Failed between "controller-freespace-schema.json" and "show freespace" JSON output..(SCGCQ01414749)


EnhancementRequests (174)
- MPI2: Add TargetModeAbort by initiator device handle.(SCGCQ00337167)
- New fault code for routine synchronous reset.(SCGCQ01264142)
- MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually.(SCGCQ00574358)
- MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag).(SCGCQ00414050)
- MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply.(SCGCQ00396414)
- MPI2: Add OEM Identifier to BIOS Page 1.(SCGCQ00357228)
- MPI2: Use Slot Information during Port Enable Event Replay option.(SCGCQ00356796)
- MPI2: Add new TargetModeAbort AbortType to only abort Command IUs.(SCGCQ00345215)
- MPI v2.6: Additional request and reply descriptor formats.(SCGCQ00259613)
- Modify event string APIs for MISSING and OFFLINE LDs.(SCGCQ01628177)
- New configuration params added for EPD-PT devices.(SCGCQ01599607)
- MR API change request to Enable/disable the parallel PD FW update feature based on PNP ID’s.(SCGCQ01595347)
- Implement Snapdump debugging capability.(SCGCQ01567770)
- Add "Incompatible with Profile" event.(SCGCQ01289924)
- API changes for CR55 - PCIe lane/link speed.(SCGCQ01222700)
- API change for Simplified RAID10 Creation.(SCGCQ01222698)
- API Changes Required for Specific OEM Backplane functionality.(SCGCQ01218406)
- API changes for PR SCGCQ01139678 - Method for determining bad ONFI flash in storcli.(SCGCQ01215334)
- MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0.(SCGCQ01213028)
- MPI 2.5: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01208954)
- API changes for PR SCGCQ01127742 - Isolating faulty cable issue from bad drive issue.(SCGCQ01203751)
- MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP.(SCGCQ01180886)
- MR 6.12 - Add JBOD mode personality to MR_CTRL_PERSONALITY.(SCGCQ01146597)
- MR 7.0: Add supportPdMapTargetId flag in MR_CTRL_INFO and MFI_CAPABILITIES.(SCGCQ01141251)
- MR 6.13: Add API support for TFM/SCAP _MR_BBU_VPD_INFO_FIXED parameters.(SCGCQ01139344)
- MR 6.13: Add a new control command to fetch ROC temperature data over I2C.(SCGCQ01137627)
- MR 7.2: Add API support to make application work with Cachecade3.0 on Ventura (Public).(SCGCQ01114969)
- MPI 2.5: Add new connector types.(SCGCQ01085073)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ01002367)
- MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout".(SCGCQ00996127)
- MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1.(SCGCQ00853162)
- MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable.(SCGCQ00791885)
- MPI 2.5: add WWID to BIOS Page 3.(SCGCQ00785208)
- MPI 2.5: update copyright info.(SCGCQ00728066)
- MPI 2.5: BIOS Page 1 additions.(SCGCQ00700829)
- MPI 2.5: distribute Target Command Buffers Received across multiple reply queues.(SCGCQ00685820)
- MPI 2.0: Add product-specific Flag bit to Clean Tool.(SCGCQ00569175)
- Add type BIOS for HashImageType..(SCGCQ00566306)
- Identify physical location of a target device.(SCGCQ00523879)
- MPI 2.5: add reserved fields to IO Unit Page 7 for future use.(SCGCQ00477817)
- MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps".(SCGCQ00471293)
- MPI 2.5: Signed images for FWDownload.(SCGCQ00469990)
- MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL.(SCGCQ00438437)
- MPI 2.5: Toolbox Console Text Display Tool.(SCGCQ00415512)
- Allow Protection Information bit for IR Volume Create.(SCGCQ00385306)
- MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply.(SCGCQ00357551)
- MPI 2.6: add PCIe Device Config Pages.(SCGCQ00345271)
- MPI 2.6: PCIe Switch Config Pages.(SCGCQ00345270)
- MPI 2.6: PCIe Topology Change List Event.(SCGCQ00345266)
- MPI 2.6: add PCIe Event Data (Generic), PCIe Device Status Change Event, and PCIe Enumeration Event.(SCGCQ00345260)
- MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors.(SCGCQ00338506)
- MPI 2.6: PCIe IO Unit Page 0 & 1 definitions.(SCGCQ00336383)
- MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1.(SCGCQ00310439)
- MPI 2.6: update SGL chapter to include PCIe.(SCGCQ00294131)
- MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request.(SCGCQ00294055)
- MPI 2.6: NVMe Encapsulated request.(SCGCQ00264759)
- MPI 2.6: SOP Encapsulated request.(SCGCQ00264755)
- Improve PERCcli Terminology When in eHBA Mode.(SCGCQ01615487)
- JSON schema for Drive level commands.(SCGCQ01445435)
- MPI 2.6 Add Atomic Request Descriptor capability.(SCGCQ00227735)
- MPI 2.6: add IO Unit Control Request.(SCGCQ00345258)
- MPI 2.6: PCIe Link Config Pages.(SCGCQ00345272)
- MPI 2.6: Enclosure Management.(SCGCQ00345273)
- Device Info field for PCIe devices.(SCGCQ00353339)
- MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request.(SCGCQ00360843)
- MPI 2.6: new family values for ProductID fields.(SCGCQ00360952)
- MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11.(SCGCQ00363600)
- Modified address space bits.(SCGCQ00397136)
- MPI 2.6: Add PCIe IO Unit Page 4.(SCGCQ00397563)
- MPI 2.6: Add board power fields to IO Unit Page 7.(SCGCQ00397572)
- MPI 2.6: Add support for SAS Persistent Connections.(SCGCQ00397577)
- MPI 2.6: Add NVMe SGL support.(SCGCQ00398256)
- MPI 2.6: Add NVMe SGL support to IEEE SGL.(SCGCQ00432541)
- MPI 2.6: System Interface Register Set update.(SCGCQ00464402)
- Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request.(SCGCQ00480292)
- MPI 2.6: shutdown operation for IO Unit Control Request.(SCGCQ00496998)
- MPI 2.6: Add supported link rates and widths for PCIe devices.(SCGCQ00564281)
- MPI 2.6: Add additional NVMe AccessStatus codes.(SCGCQ00574070)
- MPI 2.6: Add BootFlags field to Firmware Image Header.(SCGCQ00601869)
- MPI 2.6: Add new FLASH region types.(SCGCQ00619371)
- MPI 2.6: Added an additional signature value for the firmware image header.(SCGCQ00623271)
- MPI 2.6: additional AccessStatus values for PCIe Device Page 0.(SCGCQ00664957)
- MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages.(SCGCQ00680527)
- MPI 2.6: Extend Task Management - Target Reset Method to include PCIe devices.(SCGCQ00686666)
- MPI 2.6: Add device off flag to SCSI Enclosure Processor messages.(SCGCQ00776177)
- MPI 2.6: New Phy event codes added to Ventura.(SCGCQ00789600)
- MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough.(SCGCQ00813389)
- MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura.(SCGCQ00827088)
- MPI 2.6: add PCI Device ID's.(SCGCQ00828497)
- MPI 2.6: methods to report Active Cable power problems.(SCGCQ00831588)
- MPI 2.6: SRIOV support for PCIe devices.(SCGCQ00852827)
- MPI 2.6: Update Flash Signature..(SCGCQ00852831)
- profile management API.(SCGCQ00867953)
- MPI 2.6: add new feature to control NVMe SGL format.(SCGCQ00872169)
- Mega API modifications needed for RMW-FP and Cache bypass features in Ventura.(SCGCQ00875328)
-.(SCGCQ00878757)
- Merging api_overrides mega_api files with the files in the Mega_API development stream.(SCGCQ00883262)
- MPI 2.6: Update Ventura family device ids to match latest EDS.(SCGCQ00915256)
- MPI 2.6: update Marlin-class device IDs.(SCGCQ00915336)
- MPI 2.6: Remove all SOP references.(SCGCQ00925839)
- Ventura: de-feature AHCI.(SCGCQ00941620)
- MPI 2.6: Remove all AHCI references.(SCGCQ00948258)
- MPI 2.6: Add support for SAS-4 and PCIe-4.(SCGCQ00948955)
- MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0.(SCGCQ00949638)
- MPI 2.6: add LinkNum field to the PCIe Link configuration pages.(SCGCQ00954619)
-.(SCGCQ00987840)
- MPI-2.6: backend PCIe feature initialization status reporting.(SCGCQ01009104)
- MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request.(SCGCQ01013930)
- MPI2.6: Fix defines that are not unique within the first 32 characters.(SCGCQ01015826)
- MPI 2.6: direct reporting of negotiated PCIe link width and speed.(SCGCQ01017027)
- MPI 2.6: Backend SRIS mode enable flag.(SCGCQ01018687)
- MPI2.6: Reserve ExtPageTypes for Dragon.(SCGCQ01020473)
- MR_CTRL_INFO expansion from 2K to 4K.(SCGCQ01023741)
- mega api changes for ibuttonless PR.(SCGCQ01059740)
- MPI2.6: Add x16 PCI support for Marlin family products.(SCGCQ01063009)
- MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page.(SCGCQ01071374)
- Profile Management Changes to support requestedProfileID and optimisedProfile.(SCGCQ01075821)
-.(SCGCQ01082303)
-.(SCGCQ01085954)
- MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout".(SCGCQ01092340)
- MEGA_API Changes to incorporate new IO subtype to support redirect cached IO.(SCGCQ01094549)
- MPI 2.6: Add Sea Arch class and Product IDs.(SCGCQ01116837)
- MR 7.0: Add MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT = 7 to mfi.h file.(SCGCQ01133839)
- MPI2.6: Added new image type and flash region definitions.(SCGCQ01136127)
- MPI 2.6: Add new clean tool options.(SCGCQ01141732)
- MPI 2.6: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01146583)
- Define CurrentFwNvmePageSize element in new MFI_REG_STATE_EXT3 register.(SCGCQ01188725)
- MR7.1. Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01213092)
- MPI2.6: Mfg7 support for arbitrary starting slot number.(SCGCQ01213267)
- Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01216848)
- MPI 2.6: Add new firmware download type (CBB BACKUP).(SCGCQ01258005)
- MPI 2.6: Add new firmware download type (CPLD IMAGE).(SCGCQ01305760)
- MPI 2.6: add NVMe SGL Data Block descriptor alignment flag.(SCGCQ01339864)
- MPI 2.6: Add Aero PCI Device IDs.(SCGCQ01373008)
-.(SCGCQ01389581)
- MPI 2.6: Add ControllerResetTO to PCIe Device Page 2.(SCGCQ01416498)
- MPI 2.6: Add new reason code to PCIE Device Status Change Event.(SCGCQ01416515)
- Add Test Link Diagnostic API.(SCGCQ01436268)
- Add a new structure to provide OEMs ability to switch to select either I2C or PCIe as an out of band transport.(SCGCQ01445048)
- MPI 2.6: PCIe Device Page 2 reporting Namespace Optimal IO Boundary(NOIOB) for NVMe devices.(SCGCQ01449138)
- Provide OEMs ability to select either I2C or PCIe as an out of band transport.(SCGCQ01450245)
- Update description of MR_DCMD_CTRL_PERSONALITY_SET Dcmd.(SCGCQ01467149)
- Added MR_MFC_DEFAULTS.NVMeAbortTO and MR_MFC_DEFAULTS.NVMeMaxControllerResetTO.(SCGCQ01532045)
- Add support for API fields to report SED type of PD.(SCGCQ01587230)
- Add OnOff parameter in Properties2 of Structure MR_CTRL_PROP to enable/disable mix of Enterprise & Opal SED drives.(SCGCQ01593520)
- NVDATA parameter to OPAL SED.(SCGCQ01614689)
- Added a new interface between driver-aops to indicate if 64 bit SGL support is enabled.(SCGCQ01620350)
- Add new MFI Status to block requested operation due to existing controller configuration.(SCGCQ01670135)
- Change the mr.h API comment showing the new return status for the - MR_DCMD_PD_GET_INFO.(SCGCQ01670234)
- Add support to defeature Cached I/O policy.(SCGCQ01581032)
- New events for PR/CC conflicts and sector size mismatch.(SCGCQ01227051)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ00988360)
- MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses.(SCGCQ00466819)
- Removing the NMR storcli commands from storcli..(SCGCQ01445268)
- Add support to allow Device names greater than 107.(SCGCQ01039328)
- MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs.(SCGCQ00397568)
- MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit.(SCGCQ00884740)
- MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks.(SCGCQ00922213)
- MPI 2.6: Device side PCIe SRNS flag.(SCGCQ01276256)
- Checking of VBAS make file DataPro of Univ_viva_libmods.(SCGCQ01488176)
- Profile Management: Storcli - Add support for WB bit in profile management show.(SCGCQ01445628)
- Removing the NMR storcli commands from storcli..(SCGCQ01445418)
-.(SCGCQ01428114)
-.(SCGCQ01423509)
- Provide end-user ability to select either I2C or PCIe as an out of band transport.(SCGCQ01452987)
- Add NVMe device related changes.(SCGCQ01034678)
- Provide end-user ability to select either I2C or PCIe as an out of band transport.(SCGCQ01452986)
- Add boot drive selection support in Stor-CLI.(SCGCQ01445896)
- Improve PERCcli Terminology When in eHBA Mode.(SCGCQ01628424)
-.(SCGCQ01466805)
- StorCLI Libmods - Ventura LD de-allocation support on SAS/SATA SSDs through UNMAP/WRITE SAME on non-PARITY, non-DIF.(SCGCQ01448954)
- StorCLI - Ventura LD de-allocation support on SAS/SATA SSDs through UNMAP/WRITE SAME on non-PARITY, non-DIF volumes.(SCGCQ01447799)
- Adding JSON schema for JBOD and Drive level commands.(SCGCQ01445308)
- Add support for IT Firmware images and IT Completeflash images to "show file=" command.(SCGCQ01436882)

CSETActivities (57)
- StorCLI should not display SED property when using IT-HBA.(SCGCQ01600142 port of SCGCQ01589445)
- Enumeration of drives in NGM[PERCCLI Implementation / HBA330 Mini Mezz](SCGCQ01600137 port of SCGCQ01458174)
- Allow "noreset" option for IT controllers during firmware download.(SCGCQ01599545 port of SCGCQ01514483)
- Storcli show displays OS Version appended with Technical Preview.(SCGCQ01478448 port of SCGCQ01474457)
- Storcli: Instance Validation Failed between "controller-cc-schema.json" and "show consistencycheck" JSON(SCGCQ01456168 port of SCGCQ01451170)
- Phase 5 : Command "storcli /c0 show all" crashes with drives connected to SAS3.5 IT controller(SCGCQ01452992 port of SCGCQ01452982)
- Instance Validation Failed between "controller-ASO-schema.json" and "show ASO" json(SCGCQ01430285 port of SCGCQ01430237)
- SLT : Requesting user to enter the allocated response length of SMP request page(SCGCQ01202087 port of SCGCQ01202030)
- Changing ini file name to storelibconfit.ini(SCGCQ01275669 port of SCGCQ01275496)
- Unified StorCLI 7.6 : Creation of VD aborts StorCLI when FW returns error code for MR_DCMD_CFG_READ DCMD(SCGCQ01600150 port of SCGCQ01588245)
- This feature is not supported on this Controller" is displayed multiple times(SCGCQ01599461 port of SCGCQ01595717)
- Storcli may not be able to show the RAID controller in some special situation(SCGCQ01500340 port of SCGCQ01392154)
- Port linkspeed is displayed in a different JSON object for NVMe drives(SCGCQ01438288 port of SCGCQ01436920)
- Changing ini file name to storelibconfit.ini(SCGCQ01275670 port of SCGCQ01275496)
- Cutlass Phase 16 Storcli: Partner device ID should be suppressed under ./storcli /c0/eall show for multipath connections(SCGCQ01625114 port of SCGCQ01606780)
- Support only Dell SAS IT Controllers with PERCCLI(SCGCQ01618493 port of SCGCQ01547929)
- Storcli_Aero: Storcli not able to detect controller at EFI shell without Avago MR driver(SCGCQ01600151 port of SCGCQ01595698)
- Storcli returns error for show file commands when parsing MR images eventhough the command was successful(SCGCQ01600149 port of SCGCQ01529009)
- Detailed status is not displayed on locating a drive which is not connected to IT card(SCGCQ01599519 port of SCGCQ01571154)
- storcli controller show all lists EPD's in VD list(SCGCQ01599486 port of SCGCQ01556595)
- Spell error in /call/dall split mirror output(SCGCQ01599464 port of SCGCQ01595709)
- Unified StorCLI 7.6 : Read SBR fails with pre-ventura controllers(SCGCQ01539390 port of SCGCQ01539360)
- Implemented to display the full Model number of the SATA drive when connected to an IT controller(SCGCQ01528939 port of SCGCQ01525764)
- Libmod: checking-in the changes forLibmods for SCGCQ01525764(SCGCQ01528935 port of SCGCQ01528886)
- Storcli display Operating System without space for Linux version(SCGCQ01479250 port of SCGCQ01478526)
- Adding excludevd option to the help file of patrolread command(SCGCQ01445710 port of SCGCQ01443435)
- Updating readme file(SCGCQ01294583 port of SCGCQ01294570)
- SLT displays XYRATEX enclosure many fields information as "Unsupported", when we fire a command Get Enclosure Status(SCGCQ01003523 port of SCGCQ00950453)
- Libmod Changes for Defect SCGCQ01595640 (CLI does not report Serial number for Lenovo D1224 Enclosure)(SCGCQ01714307 port of SCGCQ01664412)
- Storcli_Aero: unable to set sasadd methodport on IT controller(SCGCQ01628094 port of SCGCQ01609234)
- Update help contents for jbod delete(SCGCQ01625945 port of SCGCQ01624605)
- Un-supported command displayed for "storcli64.exe /call show sasaddress"(SCGCQ01620412 port of SCGCQ01619562)
- Commands "/call/all" return inappropriate message or segfault when both MR and IT controllers are connected(SCGCQ01599483 port of SCGCQ01561703)
- Profile Management: Storcli - Add support for WB bit in profile management show(SCGCQ01454856 port of SCGCQ01445628)
- Instance Validation is failing for mentioned commands.(SCGCQ01445724 port of SCGCQ01415355)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show all" JSON output.(SCGCQ01436736 port of SCGCQ01423447)
- Application crashes while executing storcli64.exe /c0/dall set hidden=on(SCGCQ01599467 port of SCGCQ01571256)
- Storcli PR help execution delay is missing when PR running continuously(SCGCQ01537216 port of SCGCQ01534552)
- Change in RAID levels displaying in controller show all command(SCGCQ01511611 port of SCGCQ01509578)
- Upgrading the ncurses library from 5.4 to 6.0 in view of security vulnerabilities(SCGCQ01500111 port of SCGCQ01499900)
- DriveID and errormsg are coming improper on drive POH command when failed(SCGCQ01447688 port of SCGCQ01443683)
- Instance Validation Failed between "controller-freespace-schema.json" and "show freespace" JSON output.(SCGCQ01430044 port of SCGCQ01414749)
- syntax error while executing "storcli64.exe /c0 get firmware ? "(SCGCQ01620437 port of SCGCQ01618675)
- controller show all command is not listing the Battery information(SCGCQ01599459 port of SCGCQ01561689)
- Incremented devicename is programmed for all the phy's in IT controller(SCGCQ01599449 port of SCGCQ01548481)
- Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01526326 port of SCGCQ01526321)
- Unified StorCLI 7.0.1 : Programming VPD to MPB regions(SCGCQ01500006 port of SCGCQ01336460)
- Unified StorCLI 7.0.1 : Programming VPD to MPB regions(SCGCQ01500000 port of SCGCQ01336460)
- Instance Validation Failed between "controller-properties-schema.json" and "show" json output.(SCGCQ01452142 port of SCGCQ01451156)
- Updating pre-ventura SBR fails with "hwdevice" command(SCGCQ01438351 port of SCGCQ01438214)
- CLI does not report Serial number for Enclosure.(SCGCQ01714296 port of SCGCQ01595640)
- Get VPD from MPB region is failure, but overalll status shows success(SCGCQ01599481 port of SCGCQ01589618)
- Unconfigured Good PD is showing as belonging to Disk Group 0.(SCGCQ01525774 port of SCGCQ01520567)
- Controller should not be reset after firmware download in CLI for SAS 3.5 Controllers(SCGCQ01500132 port of SCGCQ01399793)
- Updating the Diag results as per new API changes(SCGCQ01537265 port of SCGCQ01537255)
- Storcli show preservedcache displays incorrect VD size on a missing VD(SCGCQ01500316 port of SCGCQ01447792)
- Assign VDs suboption in cachecade VD creation is not assigning the intended VDs.(SCGCQ01456036 port of SCGCQ01419754)

0007.0409.0000.0000- Moderate Impact/Low Probability of Occurrence
-------------------
fixes:
- Profile Mgmt API Changes.(SCGCQ00883008)
- MR_RAID_CTX_G35 has one too many bits.(SCGCQ00886417)
- Reintroduce numSGEExt Field in Raid Context for Invader to support 1MB IO.(SCGCQ00927738)
- The code had events with repetitive ID and some structures clashing.(SCGCQ00948535)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23.(SCGCQ01001936)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23 has been added back again into adapteroperations 4.(SCGCQ01014835)
- 800C error when execting Get MFC default function.(SCGCQ01037840)
- StorCLIO states wrong OS version for Windows 2016.(SCGCQ01274715)
- PH4 StorCLI -Cutlass-9305-16e FW download failed on Linux/Windows OS platforms.(SCGCQ01311728)
- Erase [excludemfg] file=<> command hangs when executed on non-op/jumpered/OCR disabled operational MR Ventura controllers.(SCGCQ01311846)
- Fixing Error Handling issues and Resource leak.(SCGCQ01319395)
- Fix for Libmod files having potential loop errors.(SCGCQ01320336)
- Cisco - CSCvd90485 - StorCLI error message incorrect when disabling LargeIO support.(SCGCQ01322003)
- EFIStorcli(1.21.12):Number of blocks in VD info is blank when queried for VD info from EFIStorcli.(SCGCQ01355452)
- Factory command is deducting the remanfacturing license even for the first time manufacturing.(SCGCQ01364604)
- Updated the Help.(SCGCQ01375059)
- controller show all command is not listing the JBODs when controller is in JBOD personality.(SCGCQ01383816)
- Controller mode reported as "Undefined" in JBOD mode in show profile output.(SCGCQ01384238)
- storcli is giving error when issuing the command dall show mirror.(SCGCQ01384690)
- Misleading message "Reboot" when erase or completeflash done in MR ventura.(SCGCQ01385373)
- storcli craches with drive show all command for some specific SATA drive.(SCGCQ01385425)
- Fixing out of bounds in libmods.(SCGCQ01385430)
- StorCli should display 128 byte inquiry for drives connected to IT controller including tape.(SCGCQ01388177)
- Save and restore with spanned volumes is throwing an error array index invalid.(SCGCQ01388543)
- PH5 StorCLI - Pre-Alpha - Show all reports NVMe drive linkspeed as "UNKNOWN".(SCGCQ01392511)
- Strocli: controller-shutdown-restart-schema.json is not in JSON format.(SCGCQ01412756)
- Storclio and storclif dispays windows version wrong for Windows 10 OS.(SCGCQ01413011)
- Storcli: Instance Validation Failed between "controller-sgpioforce-schema.json" and "set sgpioforce" JSON output.(SCGCQ01413017)
- Storcli: Instance Validation Failed between "controller-properties-schema.json" and "show" json.(SCGCQ01413239)
- Not even or regular in pattern of drive order display in storcli.(SCGCQ01415875)
- Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON.(SCGCQ01423458)
- Port linkspeed is displayed in a different JSON object for NVMe drives.(SCGCQ01436920)
- PERC10 - VD is deleted after discarding preserved cache with CLI.(SCGCQ01300897)
- Need to handle FW return code change for profile management success case.(SCGCQ01307320)
- Unified StorCLI 7.3 : Fixing resource leaks - Part 1.(SCGCQ01319405)
- PH4 Ventura PA - StorCLI - show command prints wrong information for Fury C0 in OEL6.8.(SCGCQ01321477)
- Non-operational state of FW when EFI driver is absent causing segmentation fault.(SCGCQ01324749)
- CLI reports failure when issuie DPM commands.(SCGCQ01333085)
- PH4 Ventura - StorCLI - Indentation errors observed in output while programming invalid length VPD file.(SCGCQ01346041)
- Fixing unchecked return values.(SCGCQ01385377)
- Tape drive connected to MR controller should not take NVMe speeds in to consideration.(SCGCQ01388610)
- Battery Capacitance is displayed incorrectly across different applications.(SCGCQ01389922)
- LinkSpeed is unknown for PCIe devices under Port Information headline.(SCGCQ01404583)
- Storcli: Instance Validation Failed between "controller-eghs-schema.json" and "set eghs" JSON output.(SCGCQ01412764)
- Storcli: Instance Validation Failed between "controller-securitykey-schema.json" and "set securitykey" JSON output.(SCGCQ01412948)
- Storcli: Instance Validation Failed between "controller-time-schema.json" and set time json.(SCGCQ01413222)
- This is a syntactical error where a comma was added.(SCGCQ01414744)
- Storcli: Additional string displayed in "Show wbsupport" output.(SCGCQ01415208)
- Instance Validation is failing for mentioned commands.(SCGCQ01415355)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show all" JSON output.(SCGCQ01423447)
- Second OCR request not getting triggered, fired when first OCR request about to finish, but O/P shows success.(SCGCQ01290216)
- StorCLI - Show command thorws error "failed to get information from host" in APM (ARM) CentOS.(SCGCQ01321460)
- Unified StorCLI 7.3 : Validate data to be read for controller recovery commands.(SCGCQ01359018)
- IIC mode string was used to append in case of error. I2C must be used.(SCGCQ01392046)
- Storcli 07.403.00.00 is showing Linkdown for all Phys in c0/pall show command.(SCGCQ01404219)
- Storcli: Instance Validation Failed between "controller-events-schema" and "delete events" JSON output.(SCGCQ01410438)
- Storcli: Instance Validation Failed between " controller-termlog-schema" and "delete termlog" JSON output.(SCGCQ01411534)
- Storcli: Instance Validation Failed between "controller-flushwriteverify-schema.json" and "set flus how riteverify" JSON output.(SCGCQ01412771)
- Strocli: controller-ASO-schema.json is not in JSON format.(SCGCQ01413261)
- Instance Validation Failed between "controller-ASO-schema.json" and "show ASO" json.(SCGCQ01430237)
- Updating pre-ventura SBR fails with "hwdevice" comman.(SCGCQ01438214)
- Adding excludevd option to the help file of patrolread command.(SCGCQ01443435)
- MR 7.2:PPC : StorCLi throws error while loading the saved configuration.(SCGCQ01273381)
- PH4 StorCLI - Segmentation fault observed with show command when fury/cutlass/marlin connected in FreeBSD11.0.(SCGCQ01312757)
- Unified LibMods 7.3 : Fixing resource leaks and missing return statments - Part 2.(SCGCQ01319407)
- Changing of PatrolRead Excludevd property from cli.(SCGCQ01348042)
- CLI is not showing Insight Drives with correct Enclosure/Chassis position.(SCGCQ01373639)
- Removing the memory leaks in dequelog command.(SCGCQ01411544)
- Storcli: Instance Validation Failed between "controller-coercion-schema.json" and "set coercion" JSON output.(SCGCQ01412758)
- Strocli: controller-HDD-SSD-thermalpollinterval-schema.json is not in JSON format.(SCGCQ01412934)
- Non-array delete for objects: destructors will not be called for objects in the array leading to unexpected behaviour.(SCGCQ00804672)
- Reverting back SL_MAX_OS_DRIVE_COUNT value to 300.(SCGCQ01114306)
- Fixing Out of Bounds access and Resource leak.(SCGCQ01304875)
- Inconsistencies between the applications for manage link speed.(SCGCQ01389856)
- Storcli: Instance Validation Failed between "controller-supportssdpatrolread-schema.json" and set supportssdpatrolread json.(SCGCQ01413106)
- Storcli: Instance Validation Failed between "controller-bios-schema.json" and "show bios" JSON output.(SCGCQ01413263)
- Assign VDs suboption in cachecade VD creation is not assigning the intended VDs.(SCGCQ01419754)
- StorCLI: Spindown help syntax is misleading.(SCGCQ01421610)
- Storcli shows two controllers in the system though you have only one cotntroller in the system.(SCGCQ00690355)
- StorCLI Device Interface Information field doesn't reflect inteface of actual device attached to an IT controller.(SCGCQ01352149)
- Perccli Snapshot is Enabled error when deleting VDs.(SCGCQ01378900)
- Correcting yacc rule for bbus show gasguage data command.(SCGCQ01389891)
- Strocli: controller-config-schema.json is not in JSON format.(SCGCQ01412748)
- Strocli: controller-detailed-properties-schema.json is not in JSON format.(SCGCQ01413255)
- DriveID and errormsg are coming improper on drive POH command when failed.(SCGCQ01443683)
- Correcting yacc rule of slaveaddress for command hwdevice.(SCGCQ01389890)
- Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set_personality" JSON output.(SCGCQ01412943)
- Storcli: Instance Validation Failed between "controller-smartpollinterval-schema.json" and "set smartpollinterval" json.(SCGCQ01413018)
- Storcli: Instance Validation Failed between "controller-flushwriteverify-schema.json" and "show flushwriteverify" JSON.(SCGCQ01423452)
- The structure name is changed from oob_i2c to oob to avoid compilation failure in OOB SL.(SCGCQ01015024)
- storclif64 can not create prl11 across 2 enclosure using 32 pds.(SCGCQ01295289)
- StorCLI crashes when VPD file with VPD_Length 0 is tried to update.(SCGCQ01340557)
- Removing the NMR command for setting SCAPVPD.(SCGCQ01389451)
- Storcli: Instance Validation Failed between "controller-perfmode-values-schema.json" and "set perfmode" JSON output.(SCGCQ01412938)
- Instance Validation Failed between "controller-freespace-schema.json" and "show freespace" JSON output.(SCGCQ01414749)

EnhancementRequests:
- MPI2: Add TargetModeAbort by initiator device handle.(SCGCQ00337167)
- New fault code for routine synchronous reset.(SCGCQ01264142)
- MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually.(SCGCQ00574358)
- MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag).(SCGCQ00414050)
- MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply.(SCGCQ00396414)
- MPI2: Add OEM Identifier to BIOS Page 1.(SCGCQ00357228)
- MPI2: Use Slot Information during Port Enable Event Replay option.(SCGCQ00356796)
- MPI2: Add new TargetModeAbort AbortType to only abort Command IUs.(SCGCQ00345215)
- MPI v2.6: Additional request and reply descriptor formats.(SCGCQ00259613)
- API changes for CR55 - PCIe lane/link speed.(SCGCQ01222700)
- API change for Simplified RAID10 Creation.(SCGCQ01222698)
- API Changes Required for Specific OEM Backplane functionality.(SCGCQ01218406)
- API changes for PR SCGCQ01139678 - Method for determining bad ONFI flash in storcli.(SCGCQ01215334)
- MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0.(SCGCQ01213028)
- MPI 2.5: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01208954)
- API changes for PR SCGCQ01127742 - Isolating faulty cable issue from bad drive issue.(SCGCQ01203751)
- MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP.(SCGCQ01180886)
- MR 6.12 - Add JBOD mode personality to MR_CTRL_PERSONALITY.(SCGCQ01146597)
- MR 7.0: Add supportPdMapTargetId flag in MR_CTRL_INFO and MFI_CAPABILITIES.(SCGCQ01141251)
- MR 6.13: Add API support for TFM/SCAP _MR_BBU_VPD_INFO_FIXED parameters.(SCGCQ01139344)
- MR 6.13: Add a new control command to fetch ROC temperature data over I2C.(SCGCQ01137627)
- MR 7.2: Add API support to make application work with Cachecade3.0 on Ventura (Public).(SCGCQ01114969)
- MPI 2.5: Add new connector types.(SCGCQ01085073)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ01002367)
- MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout".(SCGCQ00996127)
- MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1.(SCGCQ00853162)
- MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable.(SCGCQ00791885)
- MPI 2.5: add WWID to BIOS Page 3.(SCGCQ00785208)
- MPI 2.5: update copyright info.(SCGCQ00728066)
- MPI 2.5: BIOS Page 1 additions.(SCGCQ00700829)
- MPI 2.5: distribute Target Command Buffers Received across multiple reply queues.(SCGCQ00685820)
- MPI 2.0: Add product-specific Flag bit to Clean Tool.(SCGCQ00569175)
- Add type BIOS for HashImageType.(SCGCQ00566306)
- Identify physical location of a target device.(SCGCQ00523879)
- MPI 2.5: add reserved fields to IO Unit Page 7 for future use.(SCGCQ00477817)
- MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps".(SCGCQ00471293)
- MPI 2.5: Signed images for FWDownload.(SCGCQ00469990)
- MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL.(SCGCQ00438437)
- MPI 2.5: Toolbox Console Text Display Tool.(SCGCQ00415512)
- Allow Protection Information bit for IR Volume Create.(SCGCQ00385306)
- MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply.(SCGCQ00357551)
- MPI 2.6: add PCIe Device Config Pages.(SCGCQ00345271)
- MPI 2.6: PCIe Switch Config Pages.(SCGCQ00345270)
- MPI 2.6: PCIe Topology Change List Event.(SCGCQ00345266)
- MPI 2.6: add PCIe Event Data (Generic), PCIe Device Status Change Event, and PCIe Enumeration Event.(SCGCQ00345260)
- MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors.(SCGCQ00338506)
- MPI 2.6: PCIe IO Unit Page 0 & 1 definitions.(SCGCQ00336383)
- MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1.(SCGCQ00310439)
- MPI 2.6: update SGL chapter to include PCIe.(SCGCQ00294131)
- MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request.(SCGCQ00294055)
- MPI 2.6: NVMe Encapsulated request.(SCGCQ00264759)
- MPI 2.6: SOP Encapsulated request.(SCGCQ00264755)
-.(SCGCQ01421997)
- Controller should not be reset after firmware download in CLI for SAS 3.5 Controllers.(SCGCQ01399793)
- RPM -verify report error after installing storcli RPM package for linux.(SCGCQ01373354)
- Adding the JBOD personality with EPD passthrough support.(SCGCQ01368469)
- Added the support for EPD-PT creation and operations on a EPD-PT.(SCGCQ01368465)
- List pending profile details of the controller.(SCGCQ01346308)
-.(SCGCQ01291037)
- MPI 2.6 Add Atomic Request Descriptor capability.(SCGCQ00227735)
- MPI 2.6: add IO Unit Control Request.(SCGCQ00345258)
- MPI 2.6: PCIe Link Config Pages.(SCGCQ00345272)
- MPI 2.6: Enclosure Management.(SCGCQ00345273)
- Device Info field for PCIe devices.(SCGCQ00353339)
- MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request.(SCGCQ00360843)
- MPI 2.6: new family values for ProductID fields.(SCGCQ00360952)
- MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11.(SCGCQ00363600)
- Modified address space bits.(SCGCQ00397136)
- MPI 2.6: Add PCIe IO Unit Page 4.(SCGCQ00397563)
- MPI 2.6: Add board power fields to IO Unit Page 7.(SCGCQ00397572)
- MPI 2.6: Add support for SAS Persistent Connections.(SCGCQ00397577)
- MPI 2.6: Add NVMe SGL support.(SCGCQ00398256)
- MPI 2.6: Add NVMe SGL support to IEEE SGL.(SCGCQ00432541)
- MPI 2.6: System Interface Register Set update.(SCGCQ00464402)
- Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request.(SCGCQ00480292)
- MPI 2.6: shutdown operation for IO Unit Control Request.(SCGCQ00496998)
- MPI 2.6: Add supported link rates and widths for PCIe devices.(SCGCQ00564281)
- MPI 2.6: Add additional NVMe AccessStatus codes.(SCGCQ00574070)
- MPI 2.6: Add BootFlags field to Firmware Image Header.(SCGCQ00601869)
- MPI 2.6: Add new FLASH region types.(SCGCQ00619371)
- MPI 2.6: Added an additional signature value for the firmware image header.(SCGCQ00623271)
- MPI 2.6: additional AccessStatus values for PCIe Device Page 0.(SCGCQ00664957)
- MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages.(SCGCQ00680527)
- MPI 2.6: Extend Task Management - Target Reset Method to include PCIe devices.(SCGCQ00686666)
- MPI 2.6: Add device off flag to SCSI Enclosure Processor messages.(SCGCQ00776177)
- MPI 2.6: New Phy event codes added to Ventura.(SCGCQ00789600)
- MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough.(SCGCQ00813389)
- MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura.(SCGCQ00827088)
- MPI 2.6: add PCI Device ID's.(SCGCQ00828497)
- MPI 2.6: methods to report Active Cable power problems.(SCGCQ00831588)
- MPI 2.6: SRIOV support for PCIe devices.(SCGCQ00852827)
- MPI 2.6: Update Flash Signature..(SCGCQ00852831)
- profile management API.(SCGCQ00867953)
- MPI 2.6: add new feature to control NVMe SGL format.(SCGCQ00872169)
- Mega API modifications needed for RMW-FP and Cache bypass features in Ventura.(SCGCQ00875328)
-.(SCGCQ00878757)
- Merging api_overrides mega_api files with the files in the Mega_API development stream.(SCGCQ00883262)
- MPI 2.6: Update Ventura family device ids to match latest EDS.(SCGCQ00915256)
- MPI 2.6: update Marlin-class device IDs.(SCGCQ00915336)
- MPI 2.6: Remove all SOP references.(SCGCQ00925839)
- Ventura: de-feature AHCI.(SCGCQ00941620)
- MPI 2.6: Remove all AHCI references.(SCGCQ00948258)
- MPI 2.6: Add support for SAS-4 and PCIe-4.(SCGCQ00948955)
- MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0.(SCGCQ00949638)
- MPI 2.6: add LinkNum field to the PCIe Link configuration pages.(SCGCQ00954619)
-.(SCGCQ00987840)
- MPI-2.6: backend PCIe feature initialization status reporting.(SCGCQ01009104)
- MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request.(SCGCQ01013930)
- MPI2.6: Fix defines that are not unique within the first 32 characters.(SCGCQ01015826)
- MPI 2.6: direct reporting of negotiated PCIe link width and speed.(SCGCQ01017027)
- MPI 2.6: Backend SRIS mode enable flag.(SCGCQ01018687)
- MPI2.6: Reserve ExtPageTypes for Dragon.(SCGCQ01020473)
- MR_CTRL_INFO expansion from 2K to 4K.(SCGCQ01023741)
- mega api changes for ibuttonless PR.(SCGCQ01059740)
- MPI2.6: Add x16 PCI support for Marlin family products.(SCGCQ01063009)
- MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page.(SCGCQ01071374)
- Profile Management Changes to support requestedProfileID and optimisedProfile.(SCGCQ01075821)
-.(SCGCQ01082303)
-.(SCGCQ01085954)
- MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout".(SCGCQ01092340)
- MEGA_API Changes to incorporate new IO subtype to support redirect cached IO.(SCGCQ01094549)
- MPI 2.6: Add Sea Arch class and Product IDs.(SCGCQ01116837)
- MR 7.0: Add MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT = 7 to mfi.h file.(SCGCQ01133839)
- MPI2.6: Added new image type and flash region definitions.(SCGCQ01136127)
- MPI 2.6: Add new clean tool options.(SCGCQ01141732)
- MPI 2.6: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01146583)
- Define CurrentFwNvmePageSize element in new MFI_REG_STATE_EXT3 register.(SCGCQ01188725)
- MR7.1. Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01213092)
- MPI2.6: Mfg7 support for arbitrary starting slot number.(SCGCQ01213267)
- MPI 2.6: Add new firmware download type (CBB BACKUP).(SCGCQ01258005)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ00988360)
- MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses.(SCGCQ00466819)
- always print StorCLI version information at beginning/top of output.(SCGCQ01396733)
- StorCLI JSON 4.0 compliant schema creation for Contoller level commands.(SCGCQ01365177)
- New command in CLI OEM mode to select either PCIE or I2C as an out of band transport.(SCGCQ01353429)
- Add support to allow Device names greater than 107.(SCGCQ01039328)
- MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs.(SCGCQ00397568)
- MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit.(SCGCQ00884740)
- MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks.(SCGCQ00922213)
- Profile Management: Storcli - Add support for WB bit in profile management show.(SCGCQ01445628)
-.(SCGCQ01428114)
- Add ability to field upgrade CPLD on HBA boards.(SCGCQ01283646)
- Add NVMe device related changes.(SCGCQ01034678)
- Block the MR commands being fired to IT controllers and vice versa from StorCLI.(SCGCQ01315301)
- Unified StorCLI 7.3 : Display serial number information in StorCLI.(SCGCQ01309079)
- Unified StorCLI 7.3 : ARM EFI support to Unified StorCLI.(SCGCQ01292973)
- Unified StorCLI : [Lenovo Purley] Adding tape drive support to Unified StorCLI for IT Ventura controllers.(SCGCQ01351495)

CSETActivities:
- StorCLI firmware download to multiple target devices fails to every other device.(SCGCQ01417390 port of SCGCQ01391339)
- Unified StorCLI 7.3 : Validate data to be read for controller recovery commands.(SCGCQ01399705 port of SCGCQ01359018)
- MR 6.14-CLI: Auto Learn Period Mismatch between CTRL-R and StorCLI..(SCGCQ01396719 port of SCGCQ01391037)
- Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391818 port of SCGCQ00940993)
- The command "Storcli /c0/vall del" its deleting the VDs along with EPDs as well.(SCGCQ01304925 port of SCGCQ00915484)
- Second OCR request not getting triggered, fired when first OCR request about to finish, but O/P shows success.(SCGCQ01300741 port of SCGCQ01290216)
- Cisco - CSCvd49859 - Set VD hidden on a already hidden VD message is not correct from StorCLI.(SCGCQ01298614 port of SCGCQ01295830)
- Mr_6.12_Arm_EFI_CLI:storcli.ef /c0/vall show bbmt dose not display the corrected and uncorrected values.(SCGCQ01293051 port of SCGCQ01059790)
- MR_6.12_Arm_EFI-CLI:storcli.efi /c0/vall set ssdcaching=on/off does not apply for all the Vd's at a time.(SCGCQ01293028 port of SCGCQ01060315)
- MR_6.12_Arm_EFI-Synchronous Exception on running set vpd command with a wrong input file.(SCGCQ01293027 port of SCGCQ01059798)
- Hercules StorCLI: Progress EVents are not logged in StorCLI.(SCGCQ01291546 port of SCGCQ01288785)
- SLT : Requesting user to enter the allocated response length of SMP request page.(SCGCQ01202087 port of SCGCQ01202030)
- Changing ini file name to storelibconfit.ini.(SCGCQ01275669 port of SCGCQ01275496)
- Block OCR after Clearing NVRAM.(SCGCQ01396705 port of SCGCQ01389485)
- ER:SCGCQ00940993-Libmod Changes:Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391828 port of SCGCQ00976651)
- Tape drive connected to MR controller should not take NVMe speeds in to consideration.(SCGCQ01389395 port of SCGCQ01388610)
- Unified LibMod changes for SCGCQ01351495[Tape drive support to StorCLI].(SCGCQ01385205 port of SCGCQ01351565)
- Perccli Snapshot is Enabled error when deleting VDs.(SCGCQ01384442 port of SCGCQ01378900)
- CISCO SQA2 - LR - 1U 10 HDD - StorCLI - /c0/eall/sall start locate throws success message with no LED activity.(SCGCQ01350423 port of SCGCQ01349575 )
- Global Hot Spares shows as TR in storcli DG query when TR is activated on DG.(SCGCQ01332915 port of SCGCQ01047789)
- Correcting error messages for transport errors.(SCGCQ01332859 port of SCGCQ01093152)
- Storcli needs to be fixed for maximum TR info in ctrl show all.(SCGCQ01332851 port of SCGCQ01112673)
- Storclif64 does not return non zero error code on failure.(SCGCQ01320515 port of SCGCQ01318824)
- MR 7.2:PPC : StorCLi throws error while loading the saved configuration.(SCGCQ01318368 port of SCGCQ01273381)
- Need to handle FW return code change for profile management success case.(SCGCQ01318326 port of SCGCQ01307320)
- MR6.12_Arm_storcli.efi:Error Message Wrong on start learn cycle failure scenario.(SCGCQ01293158 port of SCGCQ01039757)
- perccli lists PDs in the wrong order - sometimes.(SCGCQ01292796 port of SCGCQ01290596)
- Storcli shows CV as optimal When Predictive Failure Bit is set.(SCGCQ01392548 port of SCGCQ01392529)
- Storcli shows CV as optimal When Predictive Failure Bit is set.(SCGCQ01392541 port of SCGCQ01392529)
- MR6.12_FW : With spun down PDs and primary path broken, FW does not allow creation of VDs.(SCGCQ01332806 port of SCGCQ01035520)
- Adding a sub option to skip the self-test while reading the POH as per customer request.(SCGCQ01292051 port of SCGCQ01074274)
- MR_6.12_ARM_Storcli.efi:storclio.efi /c0 set pcilinkspeed=3 success and set as 3%.(SCGCQ01293159 port of SCGCQ01058298)
- SLT displays XYRATEX enclosure many fields information as "Unsupported", when we fire a command Get Enclosure Status.(SCGCQ01003523 port of SCGCQ00950453)
- Update Attribution Language - Copyright, Trademark, Confidentiality to Avago.(SCGCQ00793391 port ofSCGCQ00787940)
- StorCLI displays "Next Learn Time" incorrectly.(SCGCQ01345297 port of SCGCQ01344843)
- Factory settings changes for Transport as per new MFC_DEFAULTS in API.(SCGCQ01332916 port of SCGCQ01044891)
- CLI to maintain consistency in the properties/attributes including case between MR and IT.(SCGCQ01309547 port of SCGCQ01308958)
- The command "Storcli /c0/vall del" its deleting the VDs along with EPDs as well.(SCGCQ01305204 port ofSCGCQ00915484 )
- perccli lists PDs in the wrong order - sometimes.(SCGCQ01292797 port of SCGCQ01290596)
- Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391817 port of SCGCQ00940993)
- StorCli should display 128 byte inquiry for drives connected to IT controller including tape.(SCGCQ01388560 port of SCGCQ01388177)
- Factory command is deducting the remanfacturing license even for the first time manufacturing .(SCGCQ01364653 port of SCGCQ01364604)
- Trying to Create Logical disks with UBAD drives gives wrong Failure Message from Storcli.(SCGCQ01358889 port of SCGCQ01356294)
- StorCLI displays "Next Learn Time" incorrectly.(SCGCQ01345296 port of SCGCQ01344843)
- Storcli fails with segmentation fault (core dumped) with foreign import.(SCGCQ01332905 port of SCGCQ01214152)
- C240-M5: Segmentation Fault observed when tried to delete a SWR VD from Version (Max5): 3.1(0.102).( SCGCQ01324969 port of SCGCQ01309488)
- Cisco - CSCvd49859 - Set VD hidden on a already hidden VD message is not correct from StorCLI.(SCGCQ01301733 port of SCGCQ01295830)
- Libmods: Second OCR request not triggered, fired when first OCR request about to finish, but O/P shows success(SCGCQ01290216).(SCGCQ01300727 port of SCGCQ01300721)
- Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01292007 port of SCGCQ00940993)
- ER:SCGCQ00940993-Libmod Changes:Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391827 port of SCGCQ00976651)
- storcli craches with drive show all command for some specific SATA drive.(SCGCQ01386881 port of SCGCQ01385425)
- Unified StorCLI : [Lenovo Purley] Adding tape drive support to Unified StorCLI for IT Ventura controllers.(SCGCQ01383787 port of SCGCQ01351495)
- Transport command is including all when only shared is requested, where it should be failed.(SCGCQ01332907 port of SCGCQ01093145)
- Libmods: SCGCQ01214152 - Storcli fails with segmentation fault (core dumped) with foreign import.(SCGCQ01332872 port of SCGCQ01249484)
- [Lenovo] Storcli may not be able to show the RAID controller in some special situation.(SCGCQ01392462 port of SCGCQ01389914)
- Storcli SegFault -HUU update utility doesn't detect SBMezz if Foreign Config PD exist.(SCGCQ01332850 port of SCGCQ01155309)
- Erase [excludemfg] file=<> command hangs when executed on non-op/jumpered/OCR disabled operational MR Ventura controllers.(SCGCQ01315413 port of SCGCQ01311846)
- PH4 StorCLI -Cutlass-9305-16e FW download failed on Linux/Windows OS platforms.(SCGCQ01311820 port of SCGCQ01311728)
- MR6.12_Arm_Storcli.efi:No error message shown when deleting securitykey fail.(SCGCQ01293161 port of SCGCQ01039756)
- MR6.12_Arm_EFI-CLI:Having multiple Raid volumes created,CLI lists extra entries and all operations on VD’s fails thereafter.(SCGCQ01293053 port of SCGCQ01047493)

0007.0209.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------
Fixes:
 - MegaCli and StorCli can not manage both Liberator (and prior) and TB controllers in the same system under FreeBSD with the mf(SCGCQ00355536)
 - Update VD emulation feature in StorCLI Libmods module to sync with latest APIs.(SCGCQ00357913)
 - StorCLI does not display drive information behind the Blackjack (Alta) interposer correctly(SCGCQ00357948)
 - In paged view the text " Press Enter to continue" should be changed to " Press any key to Continue"(SCGCQ00359629)
 - Code clean up in libmods and sysefi files are added(SCGCQ00359998)
 - Storcli is returning error with show(SCGCQ00360040)
 - StorCLI: Not able to set pr property includessds as onlymixed on Liberator cacheoffload controller(SCGCQ00360814)
 - iMr_Fury_StorCli:4K Drive size shown wrong in Esxi4.1U3(SCGCQ00362216)
 - storcli /c0/d0 show " in that legend missing for "Dgrd/pdgd/Onln/ofLn/Rbld"(SCGCQ00362717)
 - The legend for the PD List table exceeds 80 char limit.(SCGCQ00363455)
 - storcli query for displaying controller properties is showing status , as failure.(SCGCQ00363522)
 - iMR_Inv_6.1:StoreCLI- StoreCLI reports wrong Emulation type for VDs(SCGCQ00364097)
 - StorCLI failed to delete a VD that is just created under Windows 2008(SCGCQ00364248)
 - Reports wrong diskgroup size while querying controller level properties(SCGCQ00364622)
 - UEFI, the O/P of "Current Controller Date/Time" & "Current System Date/time" are not in proper format(SCGCQ00364735)
 - Storcli displays incomplete serial number for some SSDs(SCGCQ00366000)
 - Certain controller features displayed under "show all" exceeds 80-char limit.(SCGCQ00372155)
 - StorCLI crashed when run on a Windows 2008 64-bit with 24GB of RAM and 66 drives attached(SCGCQ00374735)
 - StorCli shows Power Saving Option as enabled, despite IBM Flatwood controller having power saving option completely disabled.(SCGCQ00377364)
 - portings of AdpRestart command(SCGCQ00378135)
 - StorCLI-Legacy:'adpbootdrive get' fails to get bootdrive information.(SCGCQ00378828)
 - Not able to get paged view of StorCLI output on VM-Ware Platform(SCGCQ00379104)
 - Cfgclr command fails without force option in Sparc OS(SCGCQ00396303)
 - storcli crashes on having a non PI drive and trying to create pi vd on all the drive(SCGCQ00413789)
 - EFI_ Storcli: Cannot set vpd file on controller, EFI hangs and cannot proceed for further operations until reboot(SCGCQ00423832)
 - Megacli crashes after invoking any command in SGI system with one 9280-8e and 2 quad port qlogic FC cards.(SCGCQ00438350)
 - Onfi_patch_6.0:Firmware crashed @Line 244 in ../../raid/1078int.c for entering into CTRL-R with Pinned cache in R60 and R6.(SCGCQ00442610)
 - SWR_1.34(SCGCQ00442652)
 - Raptor_Galaxy:State of the Shielded Drive is not displayed using storcli command(SCGCQ00467502)
 - Raptor_Galaxy_Tencent:Tencent Storcli detecting the H710 PERC card.(SCGCQ00475583)
 - Storcli internal errors should return with 1001, but its coming as -1(SCGCQ00479843)
 - Try to create a Exclusive VD, but after creation it still shows as Shared VD.(SCGCQ00484560)
 - MR6.2 : Storcli shows incorrect "Bus" information when "/c0 show all" is run(SCGCQ00518201)
 - Unable to make R10 through Ctrl R using 4k drives(SCGCQ00518579)
 - PPC64 :: MR Liberator :: Storcli Version 1.09.01 is showing wrong Creation Date and Time in VD properties(SCGCQ00569935)
 - MR_Inv_6.3_PPC:Storcli- Retreiving LDBBM info through storcli is failing on SLES11 SP2 PPC64(SCGCQ00574835)
 - "/cx/ex show phyerrorcounters" gives core dump on freeBSD 32 and 64 bit.(SCGCQ00644123)
 - Storcli : unable to set patrol read delay(SCGCQ00645195)
 - MR6.4_StorCLI_240VD: StorCLI crashes on issuing /c1 set cc=conc delay=10 starttime=2014/12/12 12 excludevd=0(SCGCQ00649324)
 - Storlib header file checkin and make compatible changes in CLI code.(SCGCQ00653742)
 - StorCLIO_1.09.09 : Not able to set subOEMid in Rhel 5.10 x64 bit.(SCGCQ00674131)
 - While creating cachecade vd with one SAS-SSD;Raid 1 option is also enabled(SCGCQ00712171)
 - H330: Firmware Crash is hit while creating the Raid1 vd without drives selected(SCGCQ00725192)
 - After Rebuilding, DHS and Expand VD operations failed to update as per VD properties(SCGCQ00730505)
 - 6.6_StorCli: StorCli lists all cascaded enclosures at position 0.(SCGCQ00756647)
 - FW breaks in iMR when excluding VD's from CC(SCGCQ00758770)
 - SupportMaxRate SATA is not listed in PD allowed operations.(SCGCQ00759178)
 - SED adapterOperation detailed is not shown in detailed show controller properties(SCGCQ00759183)
 - Adapters are not listed in sorted order.(SCGCQ00759969)
 - MR6.6: Segmentation fault (Core Dumped) in CLI when setting any invalid value for PR start time(SCGCQ00760398)
 - /c0 show all does not list hwCfg information as compared to MegaCLI.(SCGCQ00760752)
 - Storclio : Different error code is coming for 'set pcilinkspeed' in VMware 4.1U3(SCGCQ00762663)
 - StorCLI is not updated with the error Message for all new MFI_STAT added in mfistat.h(SCGCQ00765712)
 - StorCLI VMware Binary not displaying detailed description for phyerrorcounters of enclosures(SCGCQ00765762)
 - StorCLI shows CacheBypass Size and CacheBypass Mode feature enabled against a VD which is associated with a CacheCade VD(SCGCQ00772243)
 - Active operation(s) is coming as none when virtual drive erase is in progress.(SCGCQ00779789)
 - MR6.6:StorCLI shows incorrect information about "Cache Vault Flash Size"(SCGCQ00782882)
 - "cpybck" help is not coming in Legends(SCGCQ00784808)
 - VD level hide/unhide is not possible through storcli in PPC(SCGCQ00785400)
 - MFCdefaults : DisableHII option needs to be include in getShowDefaults()(SCGCQ00792232)
 - Comparing an array to null is not useful: "rawSmartData != NULL"(SCGCQ00793374)
 - MR_6.7_STROCLI: Command "./storcli64 /c0/ex/sx reset phyerrorcounters" fails in RHEL6.6 PPC64(SCGCQ00794394)
 - .(SCGCQ00800878)
 - Deallocation of the same memory more than once(SCGCQ00802031)
 - Memory leak happening in failure case since not freeing before returning error code.(SCGCQ00804588)
 - Out-of-bounds access and array delete misuse(SCGCQ00804680)
 - MR_6.7_ Storcli: "Storcli /cx/eall/sall show " gives no enclosure found if two enclosures are connected in multipath scenario(SCGCQ00805547)
 - Not able add new VD in Drive Group(SCGCQ00813314)
 - MR_6.7: Storcli Command "./storcli /c0/v2 set accesspolicy=RmvBlkd " fails for a blocked source VD.(SCGCQ00814939)
 - Storcli cannot create R10 in iMR with 6 or 8 drives per span.(SCGCQ00827049)
 - Storcli crashes instead of showing error message on enabling caching on Source VDs and C(SCGCQ00827299)
 - storcli /call show all fails with "command invalid"(SCGCQ00830269)
 - New PD_Degraded media events are not logging correctly in PPC(SCGCQ00837342)
 - Profile Mgmt API Changes(SCGCQ00883008)
 - MR_RAID_CTX_G35 has one too many bits(SCGCQ00886417)
 - Reintroduce numSGEExt Field in Raid Context for Invader to support 1MB IO(SCGCQ00927738)
 - The code had events with repetitive ID and some structures clashing(SCGCQ00948535)
 - Controller detection fails in EFI environment with MR Ventura card(SCGCQ01001372)
 - CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23(SCGCQ01001936)
 - CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23 has been added back again(SCGCQ01014835)
 - 800C error when execting Get MFC default function(SCGCQ01037840)
 - ThinkServer: Cyborg [Purley] Sotrcli (007.0022.0000.0000) cannot show the correct PCI bus/dev/func number for Invader and Ven(SCGCQ01087936)
 - Serial Number for drives were having spaces when displaying in Storcli(SCGCQ01126284)
 - No ISE Capable field(SCGCQ01148693)
 - MR7.1_NVMe:Segmentation fault seen on storcli while generating controller info with preserved cache(SCGCQ01193175)
 - Ventura-Beta: Storcli/Storclif utilities hit Segmentation fault when foreign configuration is present(SCGCQ01198698)
 - Fixing Resource leaks(SCGCQ01205356)
 - resource validation before de referencing(SCGCQ01206104)
 - Fixing resource leaks in libmods(SCGCQ01208044)
 - Fixing resource leak and pointer to local variable coverity defect in libmods(SCGCQ01209393)
 - Fixing Logically dead code and Wrong size arguments in CLI(SCGCQ01209414)
 - Unified Libmods StorCLI 7.1:Fixing resource leaks-Part 4(SCGCQ01209473)
 - Fix for resource leak in system config show(SCGCQ01210133)
 - MR7.1_NVMe: comma missing between RAID10 and RAID60 in the RAID Level Support at /c0 show all output(SCGCQ01214415)
 - Storcli does not show "NVME" in supported Drives.(SCGCQ01215383)
 - some of the drive properties is not shown properly on querying the drive info through storcli(SCGCQ01229923)
 - Unified StorCLI 7.1:Incorrect usage of STORCLIO and STORCLIF macros(SCGCQ01234217)
 - NVMe PD SMART DATA shows all 0's(SCGCQ01236052)
 - StorCLIO states wrong OS version for Windows 2016(SCGCQ01274715)
 - Individual Phy information on an IT works, when given with multiple Phys it says "Unsupported Command".(SCGCQ01275381)
 - When invalid enclsoure is specified as user input , the output is not correct(SCGCQ01275687)
 - IT show all command displays Physical Drive Information headline wihtout table when no drive is connected(SCGCQ01276688)
 - Unified StorCLI 7.2:Windows only:Drive properties headline gets truncated during drive show all command(SCGCQ01280928)
 - StorCLI: Not able to detect Liberator Controller on FreeBSD 9.0(64-bit)(SCGCQ00362421)
 - PCI Info for FreeBSD needs to be indicated as "N/A"(SCGCQ00365632)
 - Vmware CLI fails to set the phy linkspeed(SCGCQ00371445)
 - System halts on issuing storcli commands in EFI Environment.(SCGCQ00374336)
 - PERC9:Storcli ld info command displays R10 vd Span Depth to 1.(SCGCQ00374979)
 - StorCli_MR: While Creating RAID1 with four drives command facing the "C0:BAIL_OUT at line 1354" on Flatwood Board(SCGCQ00394883)
 - core dump while issuing storcli command ./storcli /c0/fall show all.(SCGCQ00448094)
 - Some Numeric values in CLI o/p comes in Hex format(SCGCQ00481474)
 - Unable to insert a drive after setting a drive as 'Missing' .(SCGCQ00490620)
 - Some sparc structures missing for storcli.(SCGCQ00504585)
 - MR Liberator : PPC SERVERGY Server : MonTask: line 541 in file ../../raid/raidpci.c(SCGCQ00567761)
 - PPC64 :: MR Liberator :: All commands of StorCli is failing with segmentation fault after creating a GlobalHotSpare(SCGCQ00579658)
 - storecli reports wrong size on 3000MB VD(SCGCQ00644545)
 - Cannot create a VD smaller than 800MB with 4K drives(SCGCQ00649962)
 - MR6.4: Storcli show command does not display all the controllers plugged into the server(SCGCQ00653672)
 - Add support bits for uneven-span and SSHA support(SCGCQ00755063)
 - MR_6.6_Storcli: Storcli reports supercap state 'unknown' while learn is happening on the controller.(SCGCQ00758101)
 - Exception with command /co show badblocks or "storcli /cx flasherase"(SCGCQ00758924)
 - SSM-FLASh drives property is displayed for regular drives.(SCGCQ00759290)
 - Support details are not shown in /c0 show all for discard cache (stalling LD deletion)(SCGCQ00759959)
 - MR_6.6: StorCLI showing incorrect value for next Schedule time for consistency check after disabling the CC(SCGCQ00760385)
 - MR 6.6 Prealpha2 Storcli:Similar PCI address(BDF number) is displayed for multiple controllers connected to FreeBSD 9.3.(SCGCQ00761937)
 - StorCLI /c0 show all command does not reflect the discard vd delete filed(SCGCQ00764658)
 - StorCLI shows CacheBypass Size and CacheBypass Mode feature enabled against a CacheCade VD(SCGCQ00765714)
 - StorCLI shows wrong "Number of blocks" for a 65.5TB VD size(SCGCQ00765759)
 - Patrol read delay is showing wrong value when set to continuous(SCGCQ00767347)
 - Showing wrong creation date for Autoconfigured virtual drives(SCGCQ00767363)
 - Storcli errors are printing in a different line.(SCGCQ00771626)
 - Storcli has option to set PR maxconcurrentpd but show is not present(SCGCQ00772302)
 - vpdpage should be read from 4 bytes to get serial number of drive(SCGCQ00772332)
 - GB scale to be added while showing CacheCade size in CLI(SCGCQ00778577)
 - MR6.6_CLI_FreeBSD: Displaying incorrect Driver name(SCGCQ00779800)
 - CTRL-R:2 iMR Card in same System hitting Montask(SCGCQ00783357)
 - Readability : Output string need to be updated for supportForceTo512e in show all command(SCGCQ00792202)
 - The HDD firmware revision is shown blank for few drives connected.(SCGCQ00793761)
 - MR_6.7_STROCLI: "./storcli64 /c0/ex show phyerrorcounters" gives segmentation fault in RHEL6.6 PPC64(SCGCQ00794393)
 - Explicit null dereferenced in rmdatamf.cpp causing wrong result.(SCGCQ00795335)
 - Resource leak(SCGCQ00804745)
 - .(SCGCQ00811452)
 - Unified StorCLI:EFI:Duplicate instances of Controller gets added to the ControllerIdList pointer(SCGCQ00936672)
 - Unified StorCLI 7.1:Coverity fixes(SCGCQ01206205)
 - Fix for profile management support check bit(SCGCQ01208103)
 - Unified StorCLI 7.1:Fxing resource leaks-Part 3(SCGCQ01209411)
 - Unified Storcli: Fixing resource leak issues(SCGCQ01209413)
 - SAS3.5 Ventura(SCGCQ01219196)
 - Discrepancy while installing and uninstalling of latest Storcli Package(SCGCQ01234153)
 - StoreCLI unified for Ventura version cannot display direct attached disk serial number information.(SCGCQ01280169)
 - pall compare shows the current linkspeed on MR controllers(SCGCQ01282376)
 - Need to handle FW return code change for profile management success case(SCGCQ01307320)
 - MegaCLI adpgetpciinfo returns a static Bus Number value "17d0"(SCGCQ00357263)
 - iMR_Inv_6.1:StorCLI- StorCLI does not show 'Unsupported/Blocked' state for 4K drives even though FW is not supporting 4K(SCGCQ00384644)
 - StorCli_MR: While creating VD using default values FW allows read policy as"Ra=Read Ahead Adaptive" as against PR-317400(SCGCQ00397663)
 - MR6.1: Hamlin: Is VD Emulated=Yes when emulationType=1(SCGCQ00424978)
 - storcli /c0 show is not listinf SWR controller(SCGCQ00454971)
 - Pcli: Pcli crashes while try to set securitykey for controller.(SCGCQ00471116)
 - Raptor Galaxy : Storcli(SCGCQ00475562)
 - Command "./Storcli /call/eall/sx set offline" fails with ERRcode1001 and ERRmsg drive not found.(SCGCQ00503981)
 - Wrong size of CacheCade VD is getting displayed after making one PD offline(SCGCQ00505771)
 - Some characters missing while querying for VD properties with having 64 VD's on a controller.(SCGCQ00529763)
 - Storclio_1.09.00:Fails to set SubOEMID on Solaris OS .(SCGCQ00568073)
 - MR_Inv_6.3_PPC:Storcli-WWN is showing blank for SAS PDs on SLES11 SP2 PPC64(SCGCQ00572800)
 - PPC64 :: MR Liberator :: ./storcli64 /c0 show dequeuelog file command failing with segmentation fault(SCGCQ00581416)
 - MR : on querying PR status, storcli hits segmentation fault.(SCGCQ00601775)
 - /c0 set cc=conc command fails with iMR card.(SCGCQ00603174)
 - storelib header file changes porting(SCGCQ00609942)
 - MR_6.4_StorCli_EFI: Storcli.efi crashes for iMR card.(SCGCQ00674023)
 - Storcli doesn't show SN of Samsung SSD 200/400/800 in SWRAID version 1.32(SCGCQ00674969)
 - storcli /c0 show all is not displaying "support vd hide" and "support HOQrebuild" feilds and legends are not displayed for HD(SCGCQ00695070)
 - In Windows and Linux only controller grouping is working but not sorting(SCGCQ00752000)
 - Boot Volume details is shown in Megacli but not with storcli.(SCGCQ00759187)
 - ASO count mismatch in show ASO w.r.t ASO in storcli show all cmd(SCGCQ00779806)
 - Reviewing the Code AdataMfi, RmDataMf and VdDataMf files.(SCGCQ00785918)
 - Missing the Display of the property temperatureCtrl.(SCGCQ00792264)
 - When Supercap SOH is reported bad, CLI still see the Supercap status as "Optimal"(SCGCQ00794760)
 - Explicit null dereferenced in vddatamf.cpp (getVdDetldInfo)(SCGCQ00795336)
 - fisResBuffer memory allocation is not considering the failure case(SCGCQ00796206)
 - Memory not freed which can cause leak(SCGCQ00804554)
 - Varailble need to be freed before returning in all failure case(SCGCQ00804650)
 - IDA show incorrect RAID controller type information(SCGCQ00806966)
 - MR_6.8_Storcli: Cachevault flash size shows differently for different commands in storcli under RHEL6.6 PPC64(SCGCQ00837197)
 - Read policy should be 'NORA' for IMR controller instead of 'none'(SCGCQ00840372)
 - ASO no mismatch between the commands 'storclif show' and 'storclif /c0 show aso'(SCGCQ01081111)
 - MR7.1_NVMe: Post NVMe VD Creation, SAS VD Creation of any Raid Level (Except R0) is not allowed(SCGCQ01127464)
 - Ventura: OEMID is shown as LSI in scheduled tasks on querying controller info.(SCGCQ01157723)
 - Removing Unused and logically dead code in storcli(SCGCQ01204045)
 - Remove all the manufacturing/Factory commands from end customer CLI tool(SCGCQ01206492)
 - Unified StorCLI 7.1-Fixing resource leaks in IT controller framework and command processors-Part2(SCGCQ01207685)
 - NVMe 7.1:Failure description string is empty in storcli(SCGCQ01234083)
 - Second OCR request not getting triggered, fired when first OCR request about to finish, but O/P shows success.(SCGCQ01290216)
 - iMR_Inv_6.1:StoreCLI-StoreCLI does not give proper message while trying to create 33rd VD on iMR FURY controller(SCGCQ00364332)
 - MR: not able to create PRL11 using 96 drives.(SCGCQ00381100)
 - StorCLI-Invader : The "coercion" mode is not in sync with the legacy values.(SCGCQ00383043)
 - Raptor Galaxy:No of blocks displayed for a VD remains same for all VD sizes.(SCGCQ00465956)
 - StorCLI reports controller status as 'OK' when Arctrus controller(9361-8i) booted in safe mode(SCGCQ00523370)
 - MR_Inv_6.3_PPC:Storcli- Storcli gives 'Segmentation fault' while retriving 'advanced software options' on SLES11 SP2 PPC64(SCGCQ00574287)
 - MR6.4_StorCLI: c0 show controller health is failing(SCGCQ00627672)
 - Add adapterOperation support details in /c0 show all for Emulationtype.(SCGCQ00759181)
 - OEMID is coming as "Unknown" for /c0 show all(SCGCQ00759862)
 - CPLD(SCGCQ00787705)
 - CPLD UPDATE : cpld upgradableCPLD support bit need to add under hardware configuration(SCGCQ00792233)
 - rlListPtr is not handled properly in failure case(SCGCQ00796227)
 - Segmentation fault while querying for GHSP/DHSP while drive is going in shield-HSP state.(SCGCQ00820392)
 - LDViewMirror is giving segmentation fault(SCGCQ00830435)
 - Storcli shows caching is enabled on Source VD when CCVD is in offline state(SCGCQ00835758)
 - Storcli gives wrong error code with respect to FW state while converting JBOD to UG(SCGCQ00839321)
 - Checking in compilation error for Libmods(SCGCQ00919973)
 - VD Creation fails with "Invalid Arguments" error with latest FW Headers(SCGCQ01001356)
 - Coverity Fixes for Unified Storcli 7.1 stream(SCGCQ01204055)
 - PH2: Pre Alpha-Ventura B0 storcli command not exited when storcli /c1 show issued.(SCGCQ01205407)
 - Fixing resource leaks and logically dead code in cli.(SCGCQ01208101)
 - Ventura B0 PH3 StorCLI : Segmentation fault seen with show command on freebsd 10.2 X86 OS(SCGCQ01250553)
 - MR 7.2:PPC : StorCLi throws error while loading the saved configuration.(SCGCQ01273381)
 - Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01274709)
 - StorCLI does not provide command to set HSM or HCOE SCGCQ00358662(SCGCQ00360745)
 - StorCLI cannot displays information for controller in Safe mode(SCGCQ00365950)
 - StorCLI does not show both "Current Write Policy" and "Default Write Policy" for VD(SCGCQ00408070)
 - debug prints are present when issuing /co/eall show(SCGCQ00475815)
 - PCLI Sparc(1.07.02):" Cli show all" command fails with error msg "Error! App exec failed in FW PCLIError! Internal".(SCGCQ00518543)
 - Verify StorCLI warns on destructive operations(SCGCQ00712982)
 - /c0 show all page are having some incorrectness in controller information(SCGCQ00716584)
 - MR6.5alpha:Segmentation fault(coredump) observed on executing ./storcli /c1/v63 show all for 64th cachecade VD in ubuntu14.04(SCGCQ00729691)
 - Add adapterOperation support details in /c0 show all for cachebypassMode.(SCGCQ00757358)
 - supportCPLDUpdate support bit needs to be updated in contoller detailed information(SCGCQ00792200)
 - supportDrvActivityLEDSetting supported bit need to be update in Supported adapater Operations(SCGCQ00792211)
 - Incorrect sizeof expression in dcmdprm(SCGCQ00793354)
 - Non-array delete for objects in rmdatamf(SCGCQ00793361)
 - Storcli displays wrong native driver version on ESXi5.5 when quered .(SCGCQ00803420)
 - Variable going out of scope without freeing which causes memory leak(SCGCQ00804663)
 - Non-array delete for objects: destructors will not be called for objects in the array leading to unexpected behaviour.(SCGCQ00804672)
 - FW hangs during SVD and CCVD migration based on DDR Size(SCGCQ00809736)
 - Unified CLI:EFI:Ventura IT:Adpcount is zero when the controller is in fault state(SCGCQ01016583)
 - Ventura:CLI App stopped working on executing /c0/eall/sall delete hotsparedrive(SCGCQ01081096)
 - Reverting back SL_MAX_OS_DRIVE_COUNT value to 300(SCGCQ01114306)
 - PD related information missing for NVMe drives(SCGCQ01126564)
 - Factory settings command needs to validate the manufacturing data in the INI, and log the license details with proper time(SCGCQ01205365)
 - Unified StorCLI 7.1:IT Firmware downgrade should be supported in StorCLIO and not StorCLI(SCGCQ01232854)
 - StorCLI(SCGCQ01274554)
 - Adapter 0: Failed to start SecureErase on Virtual Drive 0 in VMware_ESXi_5.1(SCGCQ00348911)
 - iMr_Fury_StorCLi:SectorSize show as "512KB" for 512Bytes drives(SCGCQ00362070)
 - StorcLi_5.7: Remove the description for "Ra=Read Ahead Adaptive" in VD show info.(SCGCQ00396665)
 - The bootwithpinnedcache logic is backwards, both storcli and the FW are affected(SCGCQ00436107)
 - StorCli: Segmantation fault appearing in storcli when issuing /c0/fall show(SCGCQ00564008)
 - CS2.0: Ctrl-R Domain Id is not showing in controller properties(SCGCQ00622605)
 - Storcli shows two controllers in the system though you have only one cotntroller in the system.(SCGCQ00690355)
 - Remove the code related to enableVCor feild this was used for ASD and now it is not used any more.(SCGCQ00789402)
 - supportForceFlash needs to add under suported adapter operations(SCGCQ00792205)
 - Operands don't affect result in pddatamf.cpp causing wrong result(SCGCQ00795334)
 - Unchecked return value in rmdatamf.cpp (getControllerStatus)(SCGCQ00795342)
 - MR_6.7_Storcli: Storcli reports wrong tmm and scap date of manufacture under scap properties in RHEL6.6 PPC64(SCGCQ00801311)
 - LibMod changes for CTLR+R (PERC9.2) to read Disk Write Cache settings of PD.(SCGCQ00811117)
 - StorCLI 7.0015 cannot create VD using firmware 6166 under Windows 2012(SCGCQ01046368)
 - Ventura:StorCLI-EFI-StorCLI hang on Purley @ Intel/Quanta for 3408(SCGCQ01052844)
 - SAS3 Invader/Intruder-Storcli : IR card is getting detected in EFI shell(SCGCQ01081353)
 - No details of pending FW images when run StorCLI /c0 show all after update to new firmware(SCGCQ01090082)
 - Libmod changes for defect(SCGCQ01112455) storcli says failed to exit from storelib IT library while enquiring the controller info(SCGCQ01114437)
 - PH2: Pre Alpha-Ventura B0 download completeflash command fails.(SCGCQ01198721)
 - Update /sall show legend to show powersave for SSDs in addition to spun down for HDDs(SCGCQ01213236)
 - MR7.1 StorCLI misspelling of "Drive Acitivy LED" During Set(SCGCQ01229289)
 - Help for Compare linkspeed is not complete(SCGCQ01275454)
 - CLI reporting Large VD (56TB) size slightly smaller than other apps (by .001)(SCGCQ00477037)
 - Storcli /c0 show ASO fails and delay in displaying .(SCGCQ00493491)
 - Storcli reports VD Type as "Rec1" during reconstruction on SPARC.(SCGCQ00499067)
 - Command /cx/ex show phyerrorcounters gives bus error in Orcale Enterprise Linux(SCGCQ00799426)
 - Libmod changes to support profile management(SCGCQ01048228)
 - storcliF 7.23.0.0: VD shown on wrong controller in a system with 2 Talladega 16i controllers installed(SCGCQ01080627)
 - Merge of enclosure related changes for phyerror counters from 6.x(SCGCQ01123876)
 - Ventura PH3(SCGCQ01253012)
 - Compare linkspeed says unsupported when given with multiple Phys(SCGCQ01275455)
 - coverity removing out of bounds reads from code(SCGCQ01280460)
 - CSET: storelib header file checkin for the latest changes done by storelib(SCGCQ00521999)
 - StorCLI :supportDisableImmediateIO adapter properties need to be added under show all command(SCGCQ00792085)
 - Firmware error code status MFI_STAT_SECURE_SYSTEM_PD_EXISTS needs to be update in code(SCGCQ00792234)
 - Resource leak in VdDataMf scanPartitions(SCGCQ00793363)
 - Storcli can't create AHCI LDs(SCGCQ00897637)
 - Unified StorCLI:EFI:Masking the SL_GET_CTRL_INFO command when the adapter is in invalid/bad state.(SCGCQ00936676)
 - The structure name is changed from oob_i2c to oob to avoid compilation failure in OOB SL(SCGCQ01015024)
 - NVMe PD firmware flash failing (not working) as per controller logs, StorCLI show success message(SCGCQ01218214)
 - Detailed help missing for IT erase commands(SCGCQ01275474)
 - start and stop locate from storcli on IT card with multiple drive option is not working.(SCGCQ01275671)
 - Coverity: Adding checks for unchecked return values of function calls(SCGCQ01280453)
 
Enhancement
 
 - MPI2: Add TargetModeAbort by initiator device handle(SCGCQ00337167)
 - New fault code for routine synchronous reset(SCGCQ01264142)
 - MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually(SCGCQ00574358)
 - MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag)(SCGCQ00414050)
 - MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply(SCGCQ00396414)
 - MPI2: Add OEM Identifier to BIOS Page 1(SCGCQ00357228)
 - MPI2: Use Slot Information during Port Enable Event Replay option(SCGCQ00356796)
 - MPI2: Add new TargetModeAbort AbortType to only abort Command IUs(SCGCQ00345215)
 - MPI v2.6: Additional request and reply descriptor formats(SCGCQ00259613)
 - API changes for CR55(SCGCQ01222700)
 - API change for Simplified RAID10 Creation(SCGCQ01222698)
 - API Changes Required for Specific OEM Backplane functionality(SCGCQ01218406)
 - API changes for PR SCGCQ01139678(SCGCQ01215334)
 - MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0(SCGCQ01213028)
 - MPI 2.5: Add two new reason codes to Active Cable Exception Event Data(SCGCQ01208954)
 - API changes for PR SCGCQ01127742(SCGCQ01203751)
 - MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP(SCGCQ01180886)
 - MR 6.12(SCGCQ01146597)
 - MR 7.0: Add supportPdMapTargetId flag in MR_CTRL_INFO and MFI_CAPABILITIES(SCGCQ01141251)
 - MR 6.13: Add API support for TFM/SCAP _MR_BBU_VPD_INFO_FIXED parameters(SCGCQ01139344)
 - MR 6.13: Add a new control command to fetch ROC temperature data over I2C(SCGCQ01137627)
 - MR 7.2: Add API support to make application work with Cachecade3.0 on Ventura (Public)(SCGCQ01114969)
 - MPI 2.5: Add new connector types(SCGCQ01085073)
 - MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout"(SCGCQ00996127)
 - MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply(SCGCQ00988360)
 - MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1(SCGCQ00853162)
 - MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable(SCGCQ00791885)
 - MPI 2.5: add WWID to BIOS Page 3(SCGCQ00785208)
 - MPI 2.5: update copyright info(SCGCQ00728066)
 - MPI 2.5: BIOS Page 1 additions(SCGCQ00700829)
 - MPI 2.5: distribute Target Command Buffers Received across multiple reply queues(SCGCQ00685820)
 - MPI 2.0: Add product-specific Flag bit to Clean Tool(SCGCQ00569175)
 - Add type BIOS for HashImageType.(SCGCQ00566306)
 - Identify physical location of a target device(SCGCQ00523879)
 - MPI 2.5: add reserved fields to IO Unit Page 7 for future use(SCGCQ00477817)
 - MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps"(SCGCQ00471293)
 - MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses(SCGCQ00466819)
 - MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL(SCGCQ00438437)
 - Allow Protection Information bit for IR Volume Create(SCGCQ00385306)
 - MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply(SCGCQ00357551)
 - MPI 2.6: add PCIe Device Config Pages(SCGCQ00345271)
 - MPI 2.6: PCIe Switch Config Pages(SCGCQ00345270)
 - MPI 2.6: PCIe Topology Change List Event(SCGCQ00345266)
 - MPI 2.6: add PCIe Event Data (Generic), PCIe Device Status Change Event, and PCIe Enumeration Event(SCGCQ00345260)
 - MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors(SCGCQ00338506)
 - MPI 2.6: PCIe IO Unit Page 0 & 1 definitions(SCGCQ00336383)
 - MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1(SCGCQ00310439)
 - MPI 2.6: update SGL chapter to include PCIe(SCGCQ00294131)
 - MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request(SCGCQ00294055)
 - MPI 2.6: NVMe Encapsulated request(SCGCQ00264759)
 - MPI 2.6: SOP Encapsulated request(SCGCQ00264755)
 - Added the new Component version for SBR in both Controller-info case and also in Pending FW images use case.(SCGCQ01093183)
 - Libmods changes for EFI support for Unified storcli(SCGCQ00923719)
 - Add set "Fail PD on SMARTer" property feature to StorCLI(SCGCQ00818101)
 - OEL Support for SPARC(SCGCQ00787923)
 - Added the library functions for the new MR API bits and LD operations.(SCGCQ00685010)
 - Added the library functions for the new MR API bits and LD operations.(SCGCQ00685007)
 - Display the NCQ enabled/disabled status of every SATA disk drive in the output of StorCLI and MegaCLI(SCGCQ00564477)
 - CSET: (Tbolt PR 211180) Punctured Block Logging Improvements(SCGCQ00342399)
 - MPI 2.6 Add Atomic Request Descriptor capability(SCGCQ00227735)
 - MPI 2.6: add IO Unit Control Request(SCGCQ00345258)
 - MPI 2.6: PCIe Link Config Pages(SCGCQ00345272)
 - MPI 2.6: Enclosure Management(SCGCQ00345273)
 - Device Info field for PCIe devices(SCGCQ00353339)
 - MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request(SCGCQ00360843)
 - MPI 2.6: new family values for ProductID fields(SCGCQ00360952)
 - MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11(SCGCQ00363600)
 - Modified address space bits(SCGCQ00397136)
 - MPI 2.6: Add PCIe IO Unit Page 4(SCGCQ00397563)
 - MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs(SCGCQ00397568)
 - MPI 2.6: Add board power fields to IO Unit Page 7(SCGCQ00397572)
 - MPI 2.6: Add support for SAS Persistent Connections(SCGCQ00397577)
 - MPI 2.6: Add NVMe SGL support(SCGCQ00398256)
 - MPI 2.6: Add NVMe SGL support to IEEE SGL(SCGCQ00432541)
 - MPI 2.6: System Interface Register Set update(SCGCQ00464402)
 - Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request(SCGCQ00480292)
 - MPI 2.6: shutdown operation for IO Unit Control Request(SCGCQ00496998)
 - MPI 2.6: Add supported link rates and widths for PCIe devices(SCGCQ00564281)
 - MPI 2.6: Add additional NVMe AccessStatus codes(SCGCQ00574070)
 - MPI 2.6: Add BootFlags field to Firmware Image Header(SCGCQ00601869)
 - MPI 2.6: Add new FLASH region types(SCGCQ00619371)
 - MPI 2.6: Added an additional signature value for the firmware image header(SCGCQ00623271)
 - MPI 2.6: additional AccessStatus values for PCIe Device Page 0(SCGCQ00664957)
 - MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages(SCGCQ00680527)
 - MPI 2.6: Extend Task Management(SCGCQ00686666)
 - MPI 2.6: Add device off flag to SCSI Enclosure Processor messages(SCGCQ00776177)
 - MPI 2.6: New Phy event codes added to Ventura(SCGCQ00789600)
 - MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough(SCGCQ00813389)
 - MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura(SCGCQ00827088)
 - MPI 2.6: add PCI Device ID's(SCGCQ00828497)
 - MPI 2.6: methods to report Active Cable power problems(SCGCQ00831588)
 - MPI 2.6: SRIOV support for PCIe devices(SCGCQ00852827)
 - MPI 2.6: Update Flash Signature.(SCGCQ00852831)
 - profile management API(SCGCQ00867953)
 - MPI 2.6: add new feature to control NVMe SGL format(SCGCQ00872169)
 - Mega API modifications needed for RMW-FP and Cache bypass features in Ventura(SCGCQ00875328)
 - Merging api_overrides mega_api files with the files in the Mega_API development stream(SCGCQ00883262)
 - MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit(SCGCQ00884740)
 - MPI 2.6: Update Ventura family device ids to match latest EDS(SCGCQ00915256)
 - MPI 2.6: update Marlin-class device IDs(SCGCQ00915336)
 - MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks(SCGCQ00922213)
 - MPI 2.6: Remove all SOP references(SCGCQ00925839)
 - Change library name to SLIT(SCGCQ00933175)
 - Ventura: de-feature AHCI(SCGCQ00941620)
 - MPI 2.6: Remove all AHCI references(SCGCQ00948258)
 - MPI 2.6: Add support for SAS-4 and PCIe-4(SCGCQ00948955)
 - MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0(SCGCQ00949638)
 - MPI 2.6: add LinkNum field to the PCIe Link configuration pages(SCGCQ00954619)
 - MPI-2.6: backend PCIe feature initialization status reporting(SCGCQ01009104)
 - MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request(SCGCQ01013930)
 - MPI2.6: Fix defines that are not unique within the first 32 characters(SCGCQ01015826)
 - MPI 2.6: direct reporting of negotiated PCIe link width and speed(SCGCQ01017027)
 - MPI 2.6: Backend SRIS mode enable flag(SCGCQ01018687)
 - MPI2.6: Reserve ExtPageTypes for Dragon(SCGCQ01020473)
 - MR_CTRL_INFO expansion from 2K to 4K(SCGCQ01023741)
 - mega api changes for ibuttonless PR(SCGCQ01059740)
 - MPI2.6: Add x16 PCI support for Marlin family products(SCGCQ01063009)
 - MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page(SCGCQ01071374)
 - Profile Management Changes to support requestedProfileID and optimisedProfile(SCGCQ01075821)
 - MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout"(SCGCQ01092340)
 - MEGA_API Changes to incorporate new IO subtype to support redirect cached IO(SCGCQ01094549)
 - MPI 2.6: Add Sea Arch class and Product IDs(SCGCQ01116837)
 - MR 7.0: Add MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT = 7 to mfi.h file(SCGCQ01133839)
 - MPI2.6: Added new image type and flash region definitions(SCGCQ01136127)
 - MPI 2.6: Add new clean tool options(SCGCQ01141732)
 - MPI 2.6: Add two new reason codes to Active Cable Exception Event Data(SCGCQ01146583)
 - Define CurrentFwNvmePageSize element in new MFI_REG_STATE_EXT3 register(SCGCQ01188725)
 - MR7.1. Add MR API bit to indicate the profile is NVMe Only profile(SCGCQ01213092)
 - MPI2.6: Mfg7 support for arbitrary starting slot number(SCGCQ01213267)
 - MPI 2.6: Add new firmware download type (CBB BACKUP)(SCGCQ01258005)
 - MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply(SCGCQ01002367)
 - MPI 2.5: Signed images for FWDownload(SCGCQ00469990)
 - MPI 2.5: Toolbox Console Text Display Tool(SCGCQ00415512)
 - Display the Storelib version in the show command.(SCGCQ01286063)
 - Unified StorCLI 7.1: PCIe Lane Speed and Link Configuration changes(SCGCQ01226457)
 - Unified StorCLI 7.1:OEL-Sparc support to Unified StorCLI(SCGCQ01196496)
 - Add support to allow Device names greater than 107(SCGCQ01039328)
 - Ventura : Add MR_ARRAY_EXT Support to StorCLI(SCGCQ01024636)
 - Enable SED on JBOD(SCGCQ00755527)
 - Allow VMWARE version of STORCLI cannot be run from any directory(SCGCQ00642230)
 - Added the OEM-NEC check for getting default disk-cache policy in Libmods as Disable.(SCGCQ00632051)
 - Request RAID CLI to display the Patrol Read Start Time(SCGCQ00564474)
 - Implemented the diag results to print on console(SCGCQ00525321)
 - MWCLI. R10, R50, R60, R00 VD creation(SCGCQ00369742)
 - MWCLI. Add HA support into storcli(SCGCQ00352120)
 - Create Spanned R0 array (00) in StorCLI(SCGCQ00350668)
 - Unified StorCLI 7.2:ARM-Linux support to Unified StorCLI(SCGCQ01241607)
 - Add NVMe device related changes(SCGCQ01034678)
 - Implemented the VD-VF mapping related commands in factory tool(SCGCQ00827665)
 - Complete 240VD support for utilities(SCGCQ00693042)
 - STORCLI will support MR controller management without UEFI BootServiceDriver Driver and also has retain functionality of existing seeadapter-through-driver functionality.(SCGCQ00621287)
 - dcmd path chagnes for supporting the new cachevault api(SCGCQ00381311)
 - Controller should not be reset after firmware download in CLI for SAS 3.5 Controllers(SCGCQ01399793)
 - Unified StorCLI 7.1:PPC Support(Big endian and Little endian) to Unified StorCLI(SCGCQ01196715)
 - Added the serial to properly log to the USB when the license is used for manufacturing the MFC on a controller.(SCGCQ01175821)
 - Unified CLI:Addition of appropriate device id's for Ventura(SCGCQ01132146)
 - LibMods: Increase maximum cache size for Cachecade to 2048GB. This will be named CC 2.5(SCGCQ00829204)
 - UDK Support for EFI(SCGCQ00795150)
 - Implemented the storcli command to print SATA drive's phy error counters and reset them.(SCGCQ00735171)
 - Consistent Sorting of Controllers for End Users in Customer Facing Tools(SCGCQ00696872)
 - Provide a way to enable or disable 512E using Applications(SCGCQ00351234)
 - Refer attached design doc(SCGCQ00349599)
 - Unified StorCLI : [Lenovo Purley] Adding tape drive support to Unified StorCLI for IT Ventura controllers.(SCGCQ01351495)
 - Unified StorCLI LibMods 7.1: Libmod changes for PCIe Lane Speed and Link Configuration(SCGCQ01227050)
 - Unified CLI changes to support host boot in MR with faulty FW(SCGCQ01093217)
 - Unified StorCLI:Implementing StoreLib IT static framework with StorCli(SCGCQ00916344)
 - LD Deletion stalling all IOs on Niwot HBA 12.12.0-0178(SCGCQ00757473)
 - RRB 71(SCGCQ00750164)
 - If any error that is returned as negative we return it s 0xFF from CLI to shell else FW returned error status will be returned to shell.(SCGCQ00665081)
 - SED/FDE changes for storcli Synchro(SCGCQ00632240)
 - ASD- StorCLI(SCGCQ00467863)
 - Implemented 128 drive support by using the new ENCL_INFO structures(SCGCQ00333209)
 - PERC 10 WIndows Support(SCGCQ01213160)
 - PERC 10 WIndows Support(SCGCQ01213157)
 - LibMods-Porting of MR6.x changes to Ventura(SCGCQ01109080)
 - Megacli/storcli support for lmrc driver(SCGCQ00433703)
 - PR SCGCQ00319011: Rebuild time reset(SCGCQ00381093)
 - Uneven span support is added in StorCLI.(SCGCQ00349548)
 - Unified StorCLI 7.1-Phase 2:IT Firmware downgrade support to Unified StorCLI(SCGCQ01224391)
 - Add EFI support for the manufacturing command to program.(SCGCQ01191095)
 - Ventura : Add IT Support to StorCLI [Checking in LIBMODS Changes ](SCGCQ00859216)
 - Storcli Should display SAS Address N/A if its invalid and change Host interface type names from PCIX, PCIE to PCI-X, PCI-E(SCGCQ00828476)
 - Monitoring Drive performance and predictive failure(SCGCQ00817977)
 - While saving and Restoring the configuration on controller we used to save MR_CONFIG_DATA and MR_CTRL_PROP. Added the below(SCGCQ01234118)
 - Unified StorCLI 7.1:FreeBSD OS support to Unified StorCLI 7.1(SCGCQ01191237)
 - LimMod changes related to CtrlH & MSM Mismatch on write-back options(SCGCQ00818987)
 - Functionality to extract field value from new API changes(SCGCQ00794841)
 - MR 4.12: Big endian architecture support for MR Linux driver and StorCli(SCGCQ00558815)

0007.0057.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------
Enhancement:
- Added support for ThinkSystem HBA and RAID.

1.20.20 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed an issue where command "/cx show alilog d:/logfile=xyz.txt" reports success even when destination doesn't have enough space to save log file - (SCGCQ00861227)
- Fixed an issue where command "/c0/pall show" does not show Port number and whether the Port is valid - (SCGCQ00865335)
- Fixed an issue where command "/c0/epd0,1 show" doesn't report epd1 as invalid - (SCGCQ00908866)
- Fixed an issue where command "/c0 show bootdrive" doesn't display EPD for EPDs - (SCGCQ00918811)
- Fixed an issue where command "/c0/fall show" succeeds but "/c0/fall show all" fails- (SCGCQ0043074)
- Fixed an issue where command "/c1/e83 show status" may show "Unsupported" in many fields - (SCGCQ00950438)
- Fixed an issue where command "storcli /c0/d1 set transport=on sdhsp=on" uses a dedicated hotspare even though the command requests a shared hotspare - (SCGCQ00981663)
- Fixed an issue where an incorrect message may occur when creating a RAID5 - (SCGCQ00995140)
- Fixed an issue where command "/c0/cv start retentiontest" may result in an extra "File Write ERROR !!!" print - (SCGCQ00997401)
- Fixed an issue where an incorrect failure message may occur when creating a RAID1 with 3 drives - (SCGCQ00999258)
- Fixed an issue where Virtual Drive policy isn't retained after firmware flash fails - (SCGCQ01000358)
- Fixed an issue where storcli does not display description on command success - (SCGCQ01023973)
- Fixed an issue where "force" argument may not work with "parallel" argument - (SCGCQ01026081)
- Fixed an issue where command "/c0 show autoconfig" may result in empty values - (SCGCQ01026945)
- Fixed an issue where unable to set multipath parameter when firmware returns "MFI_STAT_OK_REBOOT_REQUIRED" - (SCGCQ01029534)
- Fixed an issue where command "/c0/eall/sall download src=H7280A520.P551 parallel" may report failure and success, when the flash has failed - (SCGCQ01030430)
- Fixed an issue where Mode 5 firmware download is not working with "parallel" argument - (SCGCQ01030535)
- Fixed an issue where storcli reports "Succeeded" instead of "Initiated" during a PD firmware flash status check - (SCGCQ01031218)
- Fixed an issue where storcli shows an incorrect error message when trying to remove the Blocked Access from SVDs - (SCGCQ01039102)
- Fixed an issue where storcli only shows firmware flash status for the last drive when multiple drives are being flashed simultaneously - (SCGCQ01039484)
- Fixed an issue where storcli does not give context-specific output for storcli help commands - (SCGCQ01039534)
- Fixed an issue where command "/c0 h" does not work - (SCGCQ01039745)
- Fixed an issue where command "/c0/cv start learn" may result in an incorrect message if the learn cycle fails - (SCGCQ01039757)
- Fixed an issue where Mode F is not fired after Mode E when "activatenow" is specified with no delay - (SCGCQ01052895)
- Fixed an issue where storcli did not disable offline commands and exit when Mode E or Mode F firmware download fails - (SCGCQ01053068)
- Fixed an issue where the entire error message is not shown when trying to update the security key "rekeyLock" - (SCGCQ01059105)
- Fixed an issue where JBOD status is shown under EPD column when displaying the status message - (SCGCQ01062314)
- Fixed an issue where "Segmentation fault" error may occur when creating and deleting multiple VDs in a loop - (SCGCQ01062646)
- Fixed an issue where an saving logs to an invalid destination does not cause an error - (SCGCQ01063899)
- Fixed an issue where JBOD information is displayed in EPD mode - (SCGCQ01064101)
- Fixed an issue where MFC_DEFAULTS are not handled correctly during VD creation - (SCGCQ01070120)
- Fixed an issue where "Failed operation not possible for current RAID level" error may occur when the error should have been "resources already in use" - (SCGCQ01073669)
- Fixed an issue where multi init parameter help syntax was missing - (SCGCQ01078997)
- Fixed an issue where storcli might crash when more than 200 characters are in the command - (SCGCQ01081082)
- Fixed an issue where extra prints and incorrect messages may occur while flashing PD firmware on SAS and SATA drives at the same time - (SCGCQ01091011)
- Fixed an issue where help did not include VFQDMode values and their explanations - (SCGCQ01128071)
- Fixed an issue where command "/c0/vall set pi=off" can error even though the command was successful - (SCGCQ01133117)
- Fixed an issue where output of show init/erase operation lists as VD instead of EPD - (SCGCQ00935416)
- Fixed an issue where multiple entries of the same object in a single command still results in success - (SCGCQ00947387)
- Fixed an issue where virtual drive may disappear after starting an erase on a RAID0 VD in simple and normal mode - (SCGCQ00995154)
- Fixed an issue where command "/c0/vall set hidden=on" or "/c0/vall set hidden=off" may error even on success - (SCGCQ01026907)
- Fixed an issue where "behavior" may appear as "behaviour" - (SCGCQ01029447)
- Fixed an issue where command "/c0 show events" errors even when successful - (SCGCQ01030139)
- Fixed an issue where storcli may ask for a system reboot if changing behavior from EPD to RAID0 - (SCGCQ01035493)
- Fixed an issue where storcli may not display "behavior mode" after setting the behavior mode - (SCGCQ01035500)
- Fixed an issue where command "/cx show preservedcache" may result in a "Segmentation fault" error when pinned cache is present - (SCGCQ01036028)
- Fixed an issue where command "/c0 show phyerrorcounters" shows success without printing the table - (SCGCQ01038669)
- Fixed an issue where MRI mode is taking any value and not reflecting - (SCGCQ01039536)
- Fixed an issue where command "/cx show alilog" calculates Leap Year incorrectly - (SCGCQ01039554)
- Fixed an issue where command "/c0/fall del" may not show correct error message when controller has pinned cache and is in Safe Mode  - (SCGCQ01043063)
- Fixed an issue where controller reset command was not blocked in EFI environment - (SCGCQ01052322)
- Fixed an issue where the copyright date showed 2015 instead of 2016 - (SCGCQ01053608)
- Fixed an issue where command "storcli /c0 /v0 start erase simple patterna=1" is not setting the pattern - (SCGCQ01057994)
- Fixed an issue where "/c0 set pcilinkspeed=3" command reports success even when the command isn't sent to firmware - (SCGCQ01058298)
- Fixed an issue where MFG data shows success when inputting an invalid file - (SCGCQ01058300)
- Fixed an issue where JBOD is being displayed when querying EPD information - (SCGCQ01059088)
- Fixed an issue where error "Snapshot is enabled on the Virtual Disk" may occur when creating and deleting multiple VDs in a loop - (SCGCQ01060805)
- Fixed an issue where "show BBMT" may show information for EPDs - (SCGCQ01064035)
- Fixed an issue where error "Invalid RAID level" may be shown instead of "Cannot create raid level with 1 span" - (SCGCQ01064084)
- Fixed an issue where SATA SSD firmware cannot be flashed - (SCGCQ01085706)
- Fixed an issue where storcli does not handle the return status properly during controller firmware flash - (SCGCQ01132613)
- Fixed an issue where command "storcli /c0/v1 start migrate type=raid1 option=add drives=120:5,7" may fail - (SCGCQ00879775)
- Fixed an issue where EPD-specific operations may not work - (SCGCQ00892973)
- Fixed an issue where delete EPD command may show Delete VD success message instead of Delete EPD success - (SCGCQ00905830)
- Fixed an issue where reboot required message may not occur when toggling SRIOV - (SCGCQ00919940)
- Fixed an issue where pinned cache of EPD may generates a listing as a Virtual Drive in the preserved cache message - (SCGCQ00988786)
- Fixed an issue where storcli may fail to set JBOD=off when there are no JBODs - (SCGCQ00993464)
- Fixed an issue where force flash may not work with resetnow opton - (SCGCQ00993466)
- Fixed an issue where storcli command for bbu may not read the SuperCap VPD information properly - (SCGCQ00994876)
- Fixed an issue where storcli may error "Resource already in use" when trying to configure RAID0 with online PDs - (SCGCQ01003415)
- Fixed an issue where storcli may not be able to change the behavior mode - (SCGCQ01023985)
- Fixed a typo in remaining time when issuing command "/cx/bbu show" - (SCGCQ01024968)
- Fixed an issue where printf may be seen in libmods in power-on-hours command - (SCGCQ01033027)
- Fixed an issue where storcli may not show an error when deleting security key fails - (SCGCQ01039756)
- Fixed an issue where "/c0/dall set" command may report success even though the command is incomplete - (SCGCQ01052306)
- Fixed an issue where command "/c0 dall show" may hang or throw an exception - (SCGCQ01052841)
- Fixed an issue where command "/c0 show" may display JBOD list when the behavior is set to EPD - (SCGCQ01052876)
- Fixed an issue where command "/c0 show memscribpatterns" status may report success but description says failed - (SCGCQ01058525)
- Fixed an issue where a "Synchronous Exception" may occur when running command "/c0 set vpd" with an incorrect input file - (SCGCQ01059798)
- Fixed an issue where storcli may throw an inappropriate error when trying to flash the wrong drive firmware to a drive - (SCGCQ01065620)
- Fixed an issue where drive firmware flash with parallel option may return error code 18 - (SCGCQ01066204)
- Fixed an issue where storcli may display Nytrocache even when controller does not support it - (SCGCQ01067274)
- Fixed an issue where storcli set JBOD as boot drive and removing JBOD as boot drive may display different messages - (SCGCQ01079667)
- Fixed an issue where connector name may not be sorted properly - (SCGCQ00890604)
- Fixed an issue where command "/c0/epd20 del" may not throw error when EPD is not present - (SCGCQ00904055)
- Fixed an issue where stop erase help file may show incorrect syntax - (SCGCQ00910533)
- Fixed an issue where host name and operating system details may show client machine instead of host machine - (SCGCQ00910614)
- Fixed an issue where storcli may misspell "controller" when flushing controller - (SCGCQ00973474)
- Fixed an issue where setting Consistency Check mode may fail if no start time given, and may set successfully if wrong time is given - (SCGCQ01039758)
- Fixed an issue where some commands may not report success on success - (SCGCQ01050695)
- Fixed an issue where storcli may show the wrong message when boot drive is cleared on all drives - (SCGCQ01053241)
- Fixed an issue where "/c0/vall show all" has an inaccurate description - (SCGCQ01058116)
- Fixed an issue where an extra space may appear in the message "Flash image is not supported , Try force." - (SCGCQ01064773)
- Fixed an issue where a SAS Address mismatch may occur after setting SAS Address from storclio - (SCGCQ01082500)
- Fixed an issue where storcli may show SDS reference and multiple modes for personality switch - (SCGCQ01127378)
- Fixed an issue where help output is not available for "/c0 add jbod h" - (SCGCQ01131493)
- Fixed an issue where command "/c0/epd4 del discardcache" may throw a syntax error - (SCGCQ00904205)
- Fixed an issue where error "Add EPD failed" may occur when creating an EPD - (SCGCQ00908864)
- Fixed an issue where Auto Config option MRIE-Mode may not be SMARTMODE - (SCGCQ00922540)
- Fixed an issue where EPD may not be allowed in JBOD mode - (SCGCQ01050766)
- Fixed an issue where the table may show EPD instead of JBOD - (SCGCQ01058178)
- Fixed an issue where error " segmentation fault " may occur - (SCGCQ01063305)
- Fixed an issue where command "set cc" may fail even though cc was set successfully - (SCGCQ01074482)
- Fixed an issue where installation of storclio may fail with syntax error - (SCGCQ01074514)
- Fixed an issue where a personality switch from JBOD to EPD may not clear JBOD and EPD config - (SCGCQ01080493)
- Fixed an issue where "delete preservedcache" option may not be listed in the help menu "/c0/vx delete h" - (SCGCQ00924642)
- Fixed an issue where storcli may crash when trying to attach a CacheCade Virtual Drive to source Virtual Drive. (SCGCQ00934528)
- Fixed an issue where there may be no error message for failure to initialize EPD - (SCGCQ00935477)
- Fixed an issue where installaton of storclio may fail - (SCGCQ00952422)
- Fixed an issue where references of epdpassthru were not JBOD - (SCGCQ01023981)
- Fixed an issue where command "/c0/vall show bbmt" may not display the corrected and uncorrected values - (SCGCQ01059790)
- Fixed an issue where command "/c0/vall set ssdcaching=on/off" may not apply to all the Virtual Drives - (SCGCQ01060315)
- Fixed an issue where command "/c0/delete config" output may not be consistent - (SCGCQ01091178)
- Fixed an issue where description of "add epd" may not state success or failure - (SCGCQ00908865)
- Fixed an issue where EPD details may not show in "show all" command  - (SCGCQ00921937)
- Fixed an issue where BIOS mode may not be able to be changed by storcli - (SCGCQ01058624)
- Fixed an issue where setting lowlatency to OFF, the multipath setting is changed to OFF as well - (SCGCQ01080489)
- Fixed an issue where storcli may crash when issuing command "/c0/vall show" - (SCGCQ00888330)
- Fixed an issue where drive microcode update to directly attached drives may fail in default mode - (SCGCQ00888837)
- Fixed an issue where command "/c0/vall del" may delete EPDs as well - (SCGCQ00915484)
- Fixed an issue where SRIOV may not be enabled by storcli - (SCGCQ00915697)
- Fixed an issue where storcli may continue to prompt even when force option is used for controller firmware flash - (SCGCQ01060461)
- Fixed an issue where connector name for first 8 PHYs of enclosure may not be displayed as expected - (SCGCQ00953464, Port of SCGCQ00890597)
- Fixed an issue where description status in failure message of EPD delete may not be accurate - (SCGCQ01015016, Port of SCGCQ00988760)
- Fixed an issue where factory defaults may not be aligned with the new API - (SCGCQ01044939, Port of SCGCQ01044891)
- Fixed an issue where phyerrorcounters command may not display any PHY Error Counter values - (SCGCQ01049064, Port of SCGCQ01028993)
- Fixed an issue where "show" command may fail - (SCGCQ01004630, SCGCQ01006038, Port of SCGCQ01004617)
- Fixed an issue where command "/call show logfile=filename" may result in error "segmentaton fault"  - (SCGCQ01020010, Port of SCGCQ01019547)
- Fixed an issue where command "/c0 show dequeuelog file=filename.txt" may result in error "Segmentation fault(Core Dump)" - (SCGCQ01061120, Port of SCGCQ01014212)
- Fixed an issue where transport command may include "all" when only "shared" is requested - (SCGCQ01093159, Port of SCGCQ01093145)
- Fixed an issue where command "/c0 show alilog" may result in error "Segmentation fault(Core Dump)" - (SCGCQ01015017, Port of SCGCQ01014101)
- Fixed an issue where the hide and unhide options may not be available for a disk group - (SCGCQ01050234, Port of SCGCQ01050181)
- Fixed an issue where storcli may not generate a log - (SCGCQ00998150, Port of SCGCQ00945177)
- Fixed an issue where Global Hotspares may show as TR in disk group query - (SCGCQ01047957, Port of SCGCQ01047789)
- Fixed an issue where command "/bbu show all" may show "Remaining Time Alarm = Yes" even when not applicable  - (SCGCQ01143941, Port of SCGCQ01026187)
- Fixed an issue where maintainer name may not be populated when querying storcli version information from operating system - (SCGCQ00912697, Port of SCGCQ00838307)
- Fixed an issue where an invalid error message "Device is expander; use /c0/xp download" may be displayed on expander firmware download  - (SCGCQ01110108, Port of SCGCQ00934755)
- Fixed an issue where Virtual Drive number is not sorted in "/c0/vall show vfmap" command output - (SCGCQ00932799, Port of SCGCQ00929211)
- Fixed an issue where storcli may fail to correctly populate log files - (SCGCQ01079016, Port of SCGCQ01074584)

Enhancements:
- Added the personality change command was not present - (SCGCQ00850610)
- Extended the VFMaping to the max VFs suported by the adapter dynamically - (SCGCQ00868220)
- Added multipath support in EPD configuration options - (SCGCQ01015758)
- Added additional CPU support on EFI platform - (SCGCQ01026250)
- Added command to display progress of Patrol Read on a Physical Drive - (SCGCQ01040304)
- Added personality change features - (SCGCQ01111930)
- Added VF-queue depth mode settings - (SCGCQ00907072)
- Added ability to enable firmwre debug via storcli without UART - (SCGCQ00908320)
- Added Secure Erase support to JBOD and System drives - (SCGCQ00929757)
- Added a JBOD entity for various operations - (SCGCQ01047229)
- Added EPD support of setting EPD configuration parameter options - (SCGCQ00907064)
- Added more specific error messages in some circumstances - (SCGCQ00920034)
- Added new compilation environment and makefiles - (SCGCQ00920058)
- Added EPD and EPD-passthrough and single-drive RAID0 modes to eSDS - (SCGCQ01015739)
- Added support for drive microcode update Modes E and F - (SCGCQ01047223)
- Added code to display JBOD personality - (SCGCQ01146775)
- Updated existing implementaton to disable thermal polling in some circumstances - (SCGCQ01154338)
- Added new erase type called Crypto - (SCGCQ01050618)
- Added new command to set the multiInit EPD parameter - (SCGCQ01080273)
- Added support for drive microcode update through parallel loading - (SCGCQ01024964)
- Added support for EPD creation - (SCGCQ00887664)
- Modified a failure message to "This command only applies to Nytro Megaraid controllers. All others will display a failure status." - (SCGCQ01004610, Port of SCGCQ00881414)


1.18.11 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed issue where FW could be downleveled without using the noverchk flag (SCGCQ00924705)
- Fixed inaccurate message displayed while deleting a Cachecade Virtual Drive (CCVD) (SCGCQ00897785)
- Fixed issue where physical disk (PD) FW upgrade would fail with some SATA drives (SCGCQ00873612)
- Fixed issue where StorCLI failed to dump lastoneday pdfailevents in a file (SCGCQ00853196)
- Fixed issue where StorCLI was not reporting command success for a StorCLI64 /c0 show events file=eventLog.txt command (SCGCQ00851339)
- Fixed issue where StorCLI would not find enclosures in multipath environment (SCGCQ00873620)

Enhancements:
- Updated the BBU-properties in /c0/bbu show all (BBU learn mode) (SCGCQ00904662)
- Added the support to set and clear the transport on a DG (SCGCQ00920046)
- Added the support to change the large queue depth ctrl property in StorCLI (SCGCQ00933318)
- Implemented commands to save/restore the configuration on the controller. (SCGCQ00851795)
- Add support to detect that an OS is installed on a JBOD and to block it from being changed to Unconfigured Good (SCGCQ00828030)
- Provide a more descriptive port enumeration (SCGCQ00854620)
- Add support to enable/Disable of Large IO Support (SCGCQ00894644) 

1.16.14 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed an issue where no error message would occur when attempting to create a VD with Write-Back policy on a controller that does not support Write-Back - (SCGCQ00885617)
- Fixed an issue where StorCli would report "not in progress" for a rebuild instead of "paused" - (SCGCQ00907176)
- Fixed an issue where Foreign VD count of a spanned drive group is reported twice - (SCGCQ00911715)
- Fixed an issue where an invalid error "Device is expander,; use /c0/xp download" would occur when updating expander firmware - (SCGCQ00934755)

1.16.10 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed an issue where no StorCLI error message is displayed when attempting to create a VD with WB policy on iMR HBA (SCGCQ00885617)
- Fixed an issue where controller status shown between MSM and StorCLI may contain false flash errors (SCGCQ00888470)
- Fixed an issue StorCLI PD firmware upgrade fails due to ATA Passthrough command being built incorrectly for download microcode (SCGCQ00862914)
- Fixed an issue StorCLI does not display E252/E253 enclosure info on an 84016 SCGCQ00868143)
- Corrected StorCLI behavior and messages between consecutive expansion operations of RAID Volume (SCGCQ00870429)
- Fixed an issue RAID level migration is not happening from 0 to level 1(SCGCQ00873770)


1.14.12 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Incorporated StorCLI MegaRAID 6.6 stream

Enhancements:
- Added ability to print SATA drives phy error counters and reset them (SCGCQ00735171)
- Added consistent sorting of controllers using bus, device, function (SCGCQ00696872)
- Added ability to enable or disable 512e support (SCGCQ00351234)
- Added support for Self-Encrypting Drives in JBOD mode (SCGCQ00755527)
- Added ability for VMWare version to be run from any directory (SCGCQ00642230)
- Added ability to display NCQ enabled/disabled status of every SATA drive (SCGCQ00564477)
- Added ability to create a RAID00 (SCGCQ00350668)
- Added ability to display the Patrol Read Start Time (SCGCQ00564474)
- Added learn cycle progress information in show learn command (SCGCQ00644984)
- Added support for uneven spans (SCGCQ00349548)
- Added support for lmrc driver (SCGCQ00433703)
- Added 240 Virtual Drive support (SCGCQ00693042)
- Improved Punctured Block logging (SCGCQ00342399) 

1.12.15 - Moderate Impact/Low Probability of Occurrence
-------
Fix(es):
 - Prevent storCLI from allowing users to enable JBOD mode on
   controllers that do not support JBOD mode.
 - Updated CACHEBYPASS command to line up with user expectation.  When CACHEBYPASS is set, the user wants the cache to be bypassed. In previous versions of storcli, setting CACHEBYPASS actually disables the bypass.

1.07.07 - Moderate Impact/Low Probability of Occurrence
-------
Enhancement(s)
 - Added support for ServeRAID M1215 SAS/SATA Controller
Fix(es):
 - Fixed an issue where segmentation faults may occur in Linux.
 - Added help information for resolving vd creation command fails with 'Memory Exhausted' message in SLES 11 OS.
 - Fixed an issue where estimated time left, which range from seven or more days for Consistency Check and rebuild operations, are not displaying.

1.04.07 - Moderate Impact/Low Probability of Occurrence
-------
Enhancement(s)
 - Added support for ServeRAID M5210e and ServeRAID M5210
Fix(es):
 - Fixed an issue where a command failure results in subsequent commands and actions failing.
 - Fixed an issue where storCLI reports a segmentation fault when running the command to downgrade the controller to iMR.
 - Added help file for for storcli /cx/dx set security
 - Fixed an issue where the "show ctrlcount help" command is not displaying properly.
 - Fixed an issue where a failure is displayed in the output for querying dimmer switch information.
 - Fixed an issue where the user is not able to set securitykey on a controller, if the securitykey was set through MSM.
 - Fixed an issue where the virtual drive creation command does not give any error message when the user tries to create a private information virtual drive using normal physical drives.
 - Fixed an issue where starkly displays a firmware flash successfully completed message even though the flashing failed.
 - Synced the pause pr command with show pr command to show correct PR Current State.
 - Fixed an issue where enabling online controller reset rate (OCR) from storCLI actually disables the controller property.

1.03.11 - Initial release
-------





Lenovo Data Center Group Linux OS Support Home Page
linux.lenovo.com

© 2018-2021 Lenovo. All rights reserved