Lenovo YUM Repository
Release and Change History








Bundle Release Information:
Targeted Server Family (Machine Type): ThinkSystem SR635 (7Y98, 7Y99)
Targeted Operating System: SLES12SP5
YUM Repository Build Date: 2022_06_10

YUM Repository Release Version: 22B

Device:
ThinkSystem RAID 930-8e 4GB Flash PCIe 12Gb Adapter

Device Product Guide

Part Number: 7Y37A01087
Feature Code: AUNK
PCIe Sub Vendor ID: 0x1D49
PCIe Sub Device ID: 0x0604


Release History:

Release Change History Documents

ThinkSystem RAID 930-x xGB Flash PCIe 12Gb Adapters2Gb Adapters update BIOS and Firmware (For Linux)



BIOS and Firmware Update for ThinkSystem RAID 930-x xGB Flash PCIe 12Gb Adapters

Supported Adapters:  
	ThinkSystem RAID 930-8i 2GB Flash PCIe 12Gb Adapter  (7Y37A01084)
	ThinkSystem RAID 930-16i 4GB Flash PCIe 12Gb Adapter (7Y37A01085)
	ThinkSystem RAID 930-24i 4GB Flash PCIe 12Gb Adapter (7Y37A01086)
	ThinkSystem RAID 930-8e 4GB Flash PCIe 12Gb Adapter  (7Y37A01087)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M17A03933)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M27A03917)
	ThinkSystem  RAID 930-16i 8GB Flash PCIe 12Gb Adapter(4Y37A09721)

NOTE TO SERVICE - Reference RETAIN #N/A

Version 51.20.0-4374 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:v7.20.01.0
	UEFI Driver:0x07140000
	HII:07.20.07.00
	MR FW: 5.200.00-3637
    package 51.20.0-4374
MR 7.20

Defects:
-SPILIB2: Fix offsets in SPI2_LIB_DEVICE_PARAMS(DCSG00428841
-Etty Compression fix(DCSG00735202
-MR_7.20 missing VD's after OCR and enclosure Pull/Push(DCSG01061674
-MR_7.19_DBU: OS Assert at ioCom_wld @lsi_mr3 - While removing Aero IMR PCI devices from pass-through.(DCSG01005149
-FW hits KA when OCR Ctrl has pinned cache, while controller in Safe Mode(DCSG01061904
-Fault 0x7600 observed when 1 phy is disabled in SAS IO Unit page 1(DCSG00788430
-CC pause and resume with OCR restarts the CC on VDs that have already completed CC(DCSG01047837
-MR7.19: Aero Ctrl global fault LED is not ON when there is unconfig_bad drive on the Ctrl(DCSG01027566
-VSES : Multiple elements of SES page 0xA are assigned the same slot number(DCSG00973316
-Fix build errors related to ~\.buildver(DCSG01004381
-Fix a math error in the Memory Pool creation firmware(DCSG01024464
-PL NVMe : IOs fail with SGL length shorter than the transfer legth(DCSG00501518
-Found a lot of prints " C0:setupLd: Debug allSsdLd=1" while configure Lds using SSD drives(DCSG00931199
-PD Power State Set DCMD interface does not spin up Hot spare drives(DCSG01091672
-21B Alpha LSA: Foreign VD's, VD1 and VD2 names are not displayed in foreign config preview page.(DCSG00927138
-SCSI Compliance 2.0 Failure ASSERTION: VERIFY (16) Exceed Capacity Test(DCSG00957057
-MR 7.18 Alpha: Aero/Ventura MR: Performance: Observing 5-7% drops in SR/SW on HDD's for small IO's(DCSG00947708
-Enclosure handle for some direct attached device might be wrong during Event replay for direct attached slot order case.(DCSG00381441
-Fix static analysis issue 189500(DCSG00396542
-FW hits an exception and controller is not detected when FW upgrade from MR7.9 to MR7.16 (37 drives connected)(DCSG00984380
-AV1 SCONS: improve symbol sorting speed(DCSG00758775
-BST Failure: Memory Pool Corruption While Integrating PL 18.250.2.0 and MPI 2.6.11 Headers(DCSG00837036
-FW Logs/termlogs should change the Copyright 2017-2022(DCSG01116760
-Rebuild did not start after replace a new drive from shutdown(DCSG01030129
-Unable to change current behavior mode to NONE from RAID-0 in JBOD personality(DCSG00970577
-Assert Audit: remove 1 in SPDM client(DCSG00708196
-Update SSUTimeout Fields Value in BIOS Page 1 to 0xF0(DCSG00982364
-Unable to simulate VD policy change with different status register values on PB via megamon(DCSG01004220
-540-16i -Assertion failure @ fw\dm\pl3.5\plDmI2c.c(DCSG01013987
-Fix wrong return status on setting controller time(DCSG00905426
-Clearing the tty history with cli delete termlog command causes firmware to hang(DCSG01098208
-Fix incomplete event description during firmware flash with secured config(DCSG01028777
-Support NVMe Width is displayed as "Yes" for RAID 940-8e controller(DCSG01119307
-Fix MCTP flash firmware issue(DCSG01098220
-MR 7.19 prep for Alpha: Ventura iMR hits multiple data aborts when loading 4096 ROP(DCSG01002615
-MR 7.19 PA1:Properties are showing for unsupported drive which should be hidden(DCSG00943721
-Missing spans from R10 Virtual Drives makes system hangs at init boot screen(DCSG01031004
-MR7.20: Found a lot prints "C0:MfgMsg: Error reading device chemistry. I2C Error = 0x2" while PR(DCSG01044765
-Fix some enclosure prints(DCSG00945350
 Imbalanced bandwidth performance with 2 x4 expanders connect to Aero IT controller(DCSG00950631
 Copyback status is displayed post clearing configuration(DCSG01039193
 FW asserts on executing scrutiny phy -speed command(DCSG01089818
 4K Rand write test got poor performance from 4 drives RAID5 unexpectedly(DCSG00951753
 During Single Dip COL testing, unsuccessful restore reported(DCSG00916437
 Drive secured by non-MR FW owner does not show as "locked" when place behind Mercury OEM controller(DCSG01058849
 7.21: A hang is seen when attempting to update the the psoc using a catalog file when storcli does not support, but FW does.(DCSG01093791
 PD state change reported only once when copyback is suspended and resumed(DCSG01081139
 Aero iMR: All configs lost after system reboot/ocr(DCSG00987846
 Hot add drive on UBM backplane with x2 or X4 DFC reports incorrect element status in SES Page 02h(DCSG00967012
 Fix response to setting JBOD for unsupported drive(DCSG01041383
 [Aero] PCIe Compliance Configuration Failure - 1_44 DPA Ext Cap Struct(DCSG00972342
 ScrutinyCLI in UEFI mode failed to download Aero MR NOPAD images using hostboot (hb) command(DCSG00984134
 Update BinToRom.exe to match updated BinToRom.c(DCSG01082490
 Added "TimeSyncInterval" to the FW ManPage11 data-struct to match the XSD definition(DCSG01041327
 MR_7.20:VD target IDs changing during foreign config import - DC observed on running IOs post VD import(DCSG01045309
 Remove deprecated Vision builder(DCSG01078124
 FW not setting Opal MSID password length properly when resetting password to MSID(DCSG01042567
 Remove stray debug prints from the build(DCSG00923050
 MR7.20-Discrete part iMR controller allows PSOC flashing(DCSG01066232
 NVMe response buffer differs from host for get smart health information(DCSG01118222
 Firmware asserts during OCR with JBOD auto creation(DCSG01074021
 Fix Missing OCP ROMs Copy Back(DCSG01093193
 Code review defects(DCSG00852833
 Fix Static code analysis issue 227160(DCSG01002742
 SPILIB2 : Watchdog reset due to ARM Exception while flash under stress(DCSG00814654
 VD Failure while updating Drives(DCSG01116221
 MR 7.18: Secure drives creation using multiple secure key unable view and import the first removed encrypted VD until the second VD has been imported.(DCSG00924602
 Integrate IT Security Page Fixes into MR(DCSG01030957
 Able to set phy link speed 1.5 GBp/s from Storcli(DCSG01030969
 Update Version Field value in Std Inquiry Data of vSES Device(DCSG00966397
 Fix mfg message error(DCSG00944355
 MR 7.18 PA2: Elrond U.3x4 is showing incorrect drive count(DCSG00923028
 Aero iMR: FW crashed with DMA Config Registers task when create all disks R0(DCSG00985641
 MR 7.20: Json Event long message for missing PD needs to be updated(DCSG01040031
 Phy bad events seen for one of the Enclosure Valid Slot(DCSG01088807
 Data Abort exception happened during journaled writes(DCSG01113159
 Ventura/Mercator: pl: 4311 fault(DCSG00918020
 7.19 Aero iMR: Can't OFU with initial package, or mfc editable FWdrop(DCSG00987720
 Fix the incorrect configurablePD Count(DCSG01010108
 iMR-7.19_Firmware exception when loading LSA(DCSG00983722
 Critical Error Log created if the Firmware Download of BIOS using BIOS image from different package than Firmware.(DCSG00951807
 Fix Delayed Expansion Issue in add_catalog_rom.bat(DCSG01092304
 Update the Default Vendor ID of Virtual SES Device(DCSG01012204
 Drives not discovered when an enclosure is hot plugged after removing a PCIe switch based JBOF(DCSG00957168
 Unsupported MPI Config page read from OOB provides data in response(DCSG00937617
 Fix Static Code analysis Issues 207355, 207335, 207295(DCSG00838353
 EPD is not created after import with escrow if escrow key matches controller key(DCSG00968394
 Fix unmap writesame for a NVMe drive with small max data buffer length(DCSG00972351
 Fix Static code analysis issue 227358(DCSG01002732
 SATA only : ATA PT command for SMART READ ATTRIBUTE THRESHOLDS(B0h/D1h) fail when COUNT field is set to 0(DCSG01030777
 After Rebuild to Hot Spare, Copyback to Replacement Drive does not Start Automatically(DCSG01015011
 Data length from host to DA-SEP device not checked if it is more than buffer length in firmware(DCSG00915992
 SL OOB: NVME response buffer is not displaying user requested size of response buffer.(DCSG01151757
 Fix read wrong config page for NVMe drive behind Atlas(DCSG00954454
 Spell Checking: fix false positive handling(DCSG00916545
 Response to OOB command is not sent on Internal Dynamic Memory Allocation failure(DCSG00906577
 MR7.20_Ventura+Windbond_CV learn fails(DCSG01127762
 Remove SPDM debug logs from UART print(DCSG01022803
 [3408+ MR7.16] configurablePDCount would exceeded if set jbod on while UG drives are in spundown.(DCSG01032834
 Verify show all settings for Aero iMR show incorrect values for PSOC support and Discard Cache on LD Delete(DCSG00982497
 iMR 7.20 FW keeps dumping a message to FW log for Encs "Analyzing Status Page"(DCSG01025079
 iMR-719-EFI driver fails to load(DCSG00988360
 PERC 11 iMR : H355 Front FW hits data abort exception handler during FLR when configured as a PCIe passthru device to a VM(DCSG00996417
 Performance drop seen with direct attached SAS/SATA drives(DCSG00980873
 Foreign drive import command was successfully executed, but the drive is still marked as a foreign drive(DCSG01039809
 Remove tabs in fwSConstruct(DCSG01000963
 pl: backend PCIe: PCIe error handler fails to issue task management with cascading errors(DCSG00839445
 Fix Static code analysis issue 227329,227318(DCSG01002734
 Firmware hits assertion failure on starting Recon following a VD delete operation(DCSG01004383
 Performance drop seen with SAS/SATA drives in Windows using latest driver(DCSG00981706
 MR 7.20 PA2: truncated coverage data(DCSG01040242
 Reinstate ER 1010648(DCSG01025061
 Blue Screens while collecting "pl dbg" logs(DCSG00984451
 Storage controller goes through repeated resets and is not discovered by host(DCSG00943829
 UBM statistics data collection and UBM error handling fixes(DCSG00975065
 22B:PSOC6 -PSOC download/flash fails having Cv/BBU in failed (bad) state(DCSG01140342
 Atlas2 Veloce BST: Wait till MPT driver load complete in single host MPT testcase(DCSG01087297
 SPILIB2: (Margay Only) ARM Exception while flash under stress upon closing telnet(DCSG00914933
 MR 7.18PA2: DC seen after pinning WJ on a R50 using an enclosure(DCSG00917387
 FW returns duplicate target ID for Foreign import preview commands(DCSG00982854
 SPDM lib compile error for Ventura build(DCSG00810786
 Data Abort_Exception Core 0 when FW Device order is enabled from host(DCSG01018512
 Coverity : Remove dead code(DCSG00982343
 MR 7.18 PA1: fall import on encrypted VD results in storcli pop up message Incomplete foreign configuration(DCSG00915794
 MR7.18_Alpha:Foreign import from Mutli Span/LD drive with other drives cause, FW crash and import failure(DCSG00949516
 iMR: Legacy Mode: System reboot and PL fault detected during boot after R0,R1,JBOD creation and reboot.(DCSG01010774
 No Default value of DMA FIS Timeout(DCSG01028477
 Aero iMR: While PDs are rebuilding with IOs using all SATA drives, fw prints a lot of "PdSyncCacheTimer###..."(DCSG01020734
 Secure erase is not working properly for UG Bad drive(DCSG01106797
 Assert Audit: remove 2 related to toolbox commands(DCSG00431548
 Rebuild did not start after pull out a PD and insert a new PD iMR Aero(DCSG01012142
 Performing RLM by removing offline PDs from R1 VD to R0 VD results in reconstruction completion due to unrecoverable errors(DCSG00922691
 Assert Audit: remove 2 related to NVMe(DCSG00431546
 MR7.19PA1_After COL locked VD fails to import after becoming unlocked(DCSG00962887
 Diff drives shows as UG and sector size 0/blank in BRCM applications(DCSG01145221
 Fix controller does not show foreign config and pinned cache correctly(DCSG01050353
 Expander show status is being marked unsupported in megaraid and switch configurations(DCSG00958041
 Fix LSA time sync problem(DCSG01029543
 iMR: H350A Data Abort exception handler was called during boot with 32xR0 vds.(DCSG01007908
 Fault 0x070A observed while performing firmware downgrade.(DCSG00758163
 Foreign configuration import of sliced logical drive causing memory allocation failure(DCSG00989355
 Firmware assertion while performing firmware download using offline method on PCIe switch configuration(DCSG00956089
 MR 7.20 PA2: Code coverage code stuck printing forever(DCSG01031802
 AeroMR_7.20PA:Storcli Hangs on triggering controller restart and fails to exit command prompt(DCSG01040153
 MR719_PA1_MA drive become jbod(Unsupported) and IO will run on them(DCSG00957470
 MR 7.18PA2: Not all spans are rebuilding after pinned wj(DCSG00923279
 MR7.20-iMR-Multi-LUN / Multi-Actuator drives show up as good(DCSG01024028
 BST Failure: Revert defect 1010648(DCSG01021874
 [Aero][UBM] Enhance the link configuration to handle the link speeds for SAS/SATA drives behind UBM.(DCSG00552897
 Firmware not returning proper MFI status after CPLD update(DCSG01034288
 FW Fault 2622 observed during system boot up in some new Gen4/Gen5 servers(DCSG00947451
 FW assert is observed while performing JBOD to GOOD and vice-versa on 8 NVMe drives connected behind Atlas and drive push pull is run in parallel.(DCSG00936303
 MR 7.18: In the presence of any one of the PD in prepare for removal state,Changing the behavior mode to JBOD from None, is not making the remaining UGOOD PDs to JBOD.(DCSG00941787
 MR 7.18: Changing the behavior mode to RO from None, is not making the UGOOD PDs as RO VDs in the presence of the PD with Clear Drive or Drive Erase Process.(DCSG00908662
 RefClk enabled for sgpio backplane type(DCSG00995519
 pl: NVMe: Format Unit FMTDATA bit should be ignored(DCSG00063448
 VPD data printed on every reboot(DCSG01035788
 iMR_719_33 Drives show up after clearing foreign config(DCSG00992356
 fix Static code analysis issue(DCSG01002737
 BST Failure: Update ManPage11 for Phase 21 PL(DCSG01027882
 Fix to handle TTY Flash with write error(DCSG01077025
 Atlas-1 VSFW BST SBR test fails(DCSG01014577
 Fix Static code analysis issue 227198(DCSG01002739
 On OEM server: HII displays battery/supercap moduleVersion as "-231-4GB"(DCSG00920768
 Fix too many debug messages(DCSG01032533
 Typo and style fixes in traceTool.py(DCSG00926022
 Fix EPD boot disk not available at legacy BIOS(DCSG01111179
 (SATA Only) Inquiry command to read Block device Characteristics VPD Page fails on some SATA drives(DCSG01025293
 Two elements of SES Page A are assigned same slot number for UBM backplanes with x2 DFC(DCSG00966202
 Fatal firmware error detected after converted SATA SSD PD to JBOD(DCSG01112314
 Fix Static code analysis issue 227397(DCSG01002729
 Some of the EPDs getting listed wrongly as single drive RAID 0(DCSG01009103
 Online CPLD Update is Failing on Aero OEM IMR Controller(DCSG01008490
 FW asserts when try to create secured VDs using a FDE drive(DCSG01138487
 MR7.19:Incorrect Date and Time displayed and not in sync with OS(DCSG00967609
 Patrol read fails to correct medium error on verify capable NVME drives(DCSG01055287
 Use snprintf in some print code(DCSG00840191
 MR 7.18 PA1: Inconsistent StorCLI error message during import of VD+EPD+Foreign VD exceeding max supported configuration(DCSG00832259
 Autoconfig fails to create R0 or EPD on eligible drives in presence of Multi-Lun drives.(DCSG01030203
 When read termlogs observing Copyright as 2017-2018 which needs to be changed to 2017-2021(DCSG00960207
 Data Miscompare observed with sliced R5 Logical Drives during write(cache) policy change(DCSG01161554
 Drive changes from UG to UB, when user start the initialization followed by secure erase on same drive(DCSG00837473 (Port Of Defect(DCSG00946483)
 [Aero][PLDM] PLDM Timer restart failing(DCSG00430198 (Port Of Defect(DCSG00830822)
 SES Management is switching to ON after set autoconfig=NONE via CLI(DCSG00415487 (Port Of Defect(DCSG00995287)
 [Aero] Phase 18 build error fix(DCSG00708175 (Port Of Defect(DCSG00708188)
 "Spurious interrupt" messages seen in ttylog(DCSG00816167 (Port Of Defect(DCSG01004654)
 STP pass-thru cmd timed out(DCSG00986496 (Port Of Defect(DCSG01023742)
 R0 VD id change from 239 to VD 0 after multiple PD remove and reimport.(DCSG00424057 (Port Of Defect(DCSG00995285)
 Integrate IT Security Page Fixes into MR(DCSG01030957 (Port Of Defect(DCSG01034017)
 Boot message "Error restoring offloaded cache" popup for 940 card w/o SuperCap during AC power cycles(DCSG01087695 (Port Of Defect(DCSG01116312)
 SPDM key reading failed when complete flash Erase case(DCSG01032600 (Port Of Defect(DCSG01032601)
 FW hits an exception and controller is not detected when FW upgrade from MR7.9 to MR7.16 (37 drives connected)(DCSG00984380 (Port Of Defect(DCSG00988902)
 Incorrect PLDM firmware release date is displayed in BMC applications(DCSG00926179 (Port Of Defect(DCSG00966522)
 FW hits an ERROR: Exception Handler EXCEPTION during reboot of a server with PCIe gen5(DCSG01097640 (Port Of Defect(DCSG01107907)
 BMU set startlearntime does not set properly(DCSG00917983 (Port Of Defect(DCSG00991775)
 Fault 0xEE19 observed while running lane break test with managed switch attached to controller.(DCSG00939163 (Port Of Defect(DCSG00947866)
 [Aero][OOB] Firmware download in loop from OOB in PCIe mode fails(DCSG00555977 (Port Of Defect(DCSG00831123)
 7.21: A hang is seen when attempting to update the the psoc using a catalog file when storcli does not support, but FW does.(DCSG01093791 (Port Of Defect(DCSG01099363)
 pl: SAS IO Unit Page 1 Write Current may not cause phy to be enabled(DCSG00654031 (Port Of Defect(DCSG00734511)
 Incorrect slot number reported for drive with bad Phy(DCSG00986779 (Port Of Defect(DCSG00989522)
 Drive(s) not shown to Host after push/pull operation behind expander(DCSG00758691 (Port Of Defect(DCSG01015942)
 SATA drive is not detected during hot plug test(DCSG00975159 (Port Of Defect(DCSG01062363)
 NOTIFY(ENABLE SPINUP) is not sent to spin up legacy SAS drives when partial/slumber mode is enabled.(DCSG01044213 (Port Of Defect(DCSG01137571)
 NVME EPDs, with heavy IOs and TM from host side and NVMe passthru commands in loop from OOB. After 5-8 hrs hit KA(DCSG00939439 (Port Of Defect(DCSG00970531)
 Bad PHY events generated by RAID stack for invalid VSES elements slot with Critical status(DCSG00925970 (Port Of Defect(DCSG00927932)
 Some drives missing in OS when Direct attached slot order event replay flag is set in NVDATA(DCSG00991409 (Port Of Defect(DCSG00996085)
 Fix for allowing offline VD to be set as bootdrive(DCSG00925005 (Port Of Defect(DCSG00926405)
 Log Power State Change event for Hot spare drives spun up using MR_DCMD_PD_POWER_STATE_SET DCMD(DCSG01137533 (Port Of Defect(DCSG01138265)
 Firmware asserts during OCR with JBOD auto creation(DCSG01074021 (Port Of Defect(DCSG01091678)
 HBA hangs on boot with failed UBM backplane in a multi-UBM backplane topology(DCSG00653774 (Port Of Defect(DCSG00707457)
 FW Logs/termlogs should change the Copyright 2017-2022(DCSG01116760 (Port Of Defect(DCSG01119586)
 MR_7.20 missing VD's after OCR and enclosure Pull/Push(DCSG01061674 (Port Of Defect(DCSG01074900)
 Fix unmap writesame for a NVMe drive with small max data buffer length(DCSG00972351 (Port Of Defect(DCSG01005797)
 Secure erase is allowed on JBOD/EPD(DCSG00840773 (Port Of Defect(DCSG01015944)
 Fix LSA time sync problem(DCSG01029543 (Port Of Defect(DCSG01034066)
 Incorrect usage of Block Limits Virtual physical disk npwg field resulting in 0x7 being treated as 7 512B sector length IOs with NVMe drives(DCSG01026871 (Port Of Defect(DCSG01032306)
 Fix MR recovery retry timer.(DCSG00926330 (Port Of Defect(DCSG00992338)
 Fault 0xEC0F seen while aborting an active recovery on a NVMe drive(DCSG01021656 (Port Of Defect(DCSG01023749)
 FW stuck in COL-BIOS Reset loop when COL times out(DCSG00907382 (Port Of Defect(DCSG00932410)
 MR7.20-Discrete part iMR controller allows PSOC flashing(DCSG01066232 (Port Of Defect(DCSG01070280)
 MR7.20-Drive pull during recon-Assertion failure in fw\raid\pd.c at line 8254 AR Invalid(DCSG01054517 (Port Of Defect(DCSG01066945)
 Kill adapter seen on multiple EPDs with IOs with TMs(DCSG00923995 (Port Of Defect(DCSG00970534)
 Clearing the tty history with cli delete termlog command causes firmware to hang(DCSG01098208 (Port Of Defect(DCSG01108301)
 MR7.20: Found a lot prints "C0:MfgMsg: Error reading device chemistry. I2C Error = 0x2" while PR(DCSG01044765 (Port Of Defect(DCSG01077927)
 Unable to simulate VD policy change with different status register values on PB via megamon(DCSG01004220 (Port Of Defect(DCSG01008661)
 Patrol read fails to correct medium error on verify capable NVME drives(DCSG01055287 (Port Of Defect(DCSG01078110)
 Fixed fault 0xF000 when doing VSES task management(DCSG00927996 (Port Of Defect(DCSG00934187)
 Connector name in SAS Device Page 0 of the VSes/DA-SEP is not set correctly(DCSG00995575 (Port Of Defect(DCSG01003869)
 Kill adapter seen on multiple EPDs with IOs with TMs(DCSG00923995 (Port Of Defect(DCSG01015951)
 Memory Scrub DDR Pattern Operation crashes the controller(DCSG00908167 (Port Of Defect(DCSG00920939)
 Aero 7.19 iMR: CBB unable to find secondary image(DCSG00987835 (Port Of Defect(DCSG01038387)
 KeyID is cleared before the transition is finished(DCSG00936150 (Port Of Defect(DCSG00977211)
 NVRAM signature invalid. Aborting DDR scrub & ECC check!!!(DCSG01111513 (Port Of Defect(DCSG01126920)
 (SATA Only) IO Timeouts seen while running Unmap, SATA Passthrough and Read/Write IOs to a SATA drive(DCSG00654439 (Port Of Defect(DCSG00831920)
 FW asserts when try to create secured VDs using a FDE drive(DCSG01138487 (Port Of Defect(DCSG01148515)
 MCTP : MCTP MPI requests are failed with drive missing status even when drive is present(DCSG00952803 (Port Of Defect(DCSG00956655)
 SATA : one or more HDD are not discovered by OS when drives behind expander are powered ON(DCSG00947126 (Port Of Defect(DCSG00964427)
 Drive changes from UG to UB, when user start the initialization followed by secure erase on same drive(DCSG00837473 (Port Of Defect(DCSG01015953)
 [3408+ MR7.16] configurablePDCount would exceeded if set jbod on while UG drives are in spundown.(DCSG01032834 (Port Of Defect(DCSG01044605)
 Bad sensor slot case should not counted again when marking slot bad.(DCSG00961696 (Port Of Defect(DCSG00977229)
 VD Failure while updating Drives(DCSG01116221 (Port Of Defect(DCSG01124651)
 DMA error observed during xtools 'show' command in Atlas behind Aero config(DCSG01051896 (Port Of Defect(DCSG01079552)
 Controller Faults when connected to DA SEP Backplane(DCSG00916381 (Port Of Defect(DCSG00918045)
 Incorrect message while importing only the locked foreign config(DCSG00963973 (Port Of Defect(DCSG01023874)
 Secure erase is allowed on JBOD/EPD(DCSG00840773 (Port Of Defect(DCSG00970537)
 Assertion failure in FW when user initiate rebuild on partial degraded R6 VD(DCSG00921397 (Port Of Defect(DCSG01015950)
 FW hits an ERROR: Exception Handler EXCEPTION during reboot of a server with PCIe gen5(DCSG01097640 (Port Of Defect(DCSG01107908)
 FW hits an exception and controller is not detected when FW upgrade from MR7.9 to MR7.16 (37 drives connected)(DCSG00984380 (Port Of Defect(DCSG00988901)
 CLI application shows improper error import message after successful Foreign import(DCSG00915940 (Port Of Defect(DCSG01015959)
 PCIE failure causes TBM failure which leads to control plane hang(DCSG00969750 (Port Of Defect(DCSG00990809)
 Dev-defect: WRITE with a transfer-size of 0 results in a hang.(DCSG00380906 (Port Of Defect(DCSG00904252)
 If personality mode is "undefined", FW set to RAID mode but still set new hotplug drive to JBOD state and auto rebuild does not start(DCSG00928865 (Port Of Defect(DCSG01015962)
 Firmware assertion while performing firmware download using offline method on PCIe switch configuration(DCSG00956089 (Port Of Defect(DCSG01034998)
 Some drives and enclosures not added to Windows OS when SAS/SATA devices are reduced in NVDATA.(DCSG00654062 (Port Of Defect(DCSG00757561)
 Assertion failure in FW when user initiate rebuild on partial degraded R6 VD(DCSG00921397 (Port Of Defect(DCSG00970530)
 Incorrect PLDM firmware release date is displayed in BMC applications(DCSG00926179 (Port Of Defect(DCSG01015961)
 Delayed response while application firmware and IOs running(DCSG00759013 (Port Of Defect(DCSG00775564)
 CLI application shows improper error import message after successful Foreign import(DCSG00915940 (Port Of Defect(DCSG00970535)
 Controller marks a drive UBUnsp if the server is rebooted while running Sanitize Overwrite(DCSG01141274 (Port Of Defect(DCSG01165082)

EnhancementRequests:
 Spell Checking Corrections Part 1(DCSG00561599
 Update ControllerInfo Structure with PartNumber - API Changes(DCSG01064529
 ATA Passthrough handling of ATA commands(PIO DATA IN) obsolete in latest ATA specification for backward compatibility(DCSG00999763
 Safestore: MegaRAID key management feature: temporary key escrow(DCSG00918486
 Clean up include files(DCSG00977963
 added new BST file for shenandoah(DCSG01108340
 SPILIB2: Add support for new Cypress parts via proprietary CFI Method(DCSG00734502
 MPI 2.6: Header file changes associated with revision 2.6.11(DCSG00293141
 pl: backend PCIe: target link speed diag command(DCSG00757333
 Update XSDs with Proper Active High/Low Flags for GPIO_LED_GLOBAL_FAULT(DCSG01082422
 Snapdump: Remove duplicate entry in additional battery statistics(DCSG00951438
 Reorder Snapdump files for reliability(DCSG01008677
 Add PSoC 6 FW to Catalog File(DCSG01107483
 Add Firmware Version 9 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01136458
 Atlas1 VS BST framework and deployment(DCSG00548501
 Assert Audit : Memory Allocation Asserts(DCSG00816160
 PEX89000:Use SDB to inject errors in Error Counter BST testcase(DCSG01079551
 Assert Audit 7.18: remove 18 from ddf(DCSG00914502
 Add support to srcgen.py and binToRom.exe to store Vision HW/FW version, board type and Version string info for HW/FW/type compatibility checks.(DCSG00920667
 Create offload expected status field in NVSRAM(DCSG01098154
 SRAM layout changes for code coverage(DCSG01026846
 Assert Audit : Memory Allocation Asserts(DCSG00816162
 Add Firmware Version 6 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01126019
 Enhance autoimport to prioritize existing configurations over foreign config(DCSG00430812
 Update linker script file for mbed TLS component(DCSG00966563
 Assert Analysis : Removing FC/CS/BLOCK/PAGE checking(DCSG00527882
 Integrate MPI 2.6.11 headers(DCSG00408836
 Assert Audit 7.18: remove 2 from fw/hw(DCSG00919003
 Remove two Asserts from code(DCSG00424055
 SPILIB2: Eliminate incompatible erase commands in MultiErase mode(DCSG00830450
 Remove unnecessary assert from code(DCSG00816200
 Remove old MCTP OEM-conditional code(DCSG01016044
 Add Interposer PSoC 6 FW to Catalog File(DCSG01121802
 Update 9500-16i, 8i channel XMLs to support new VPP backplane management device address.(DCSG00351950
 Dump code coverage counters for Ondemand Snapdump(DCSG01020724
 Check in the build system's supporting function that can checks print statement consistency(DCSG00977490
 SPILIB2: Add support for serial mode for parts with QE=1 and dual mode support(DCSG00831421
 Add Lmid/Smid local/host mem dump into SD(DCSG00289727
 Add partial xml for 9502-16i Controller OCP form factor(DCSG00961958
 Integrate SPILIB 2.0 into MR Firmware for Aero, Sea and Ventura(DCSG00040487
 SPDM feature compile out from FW code(DCSG00707071
 Release Automation: Assign release type when creating ROP(DCSG00941419
 Add control command MFI_OOB_MCTP_CONTROL_EXCEPTION_NO_CMD (0x99) in API(DCSG01065378
 Add Firmware Version 7 for PartNumber 29211 to PSoC Catalog Image(DCSG01128627
 secureSignSPDM: implement automation to revoke device certs, check CRL and check revocation status for a device cert(DCSG01004627
 [UBM] Add detection of SAS/SATA drive with UBM backplane supporting IFDET2# and PRSNT#(DCSG00945423
 Add Firmware Version 5 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01123516
 Atlas_BST:Enhancement for atlas bst to run on shared as well as developer systems(DCSG01002782
 SPILIB2: Add High Level SPI Emulation Library(DCSG00508974
 Reorder Snapdump data collection for reliability(DCSG00991989
 Add NVDATA option to change DMA Activate FIS timeout value.(DCSG00952761
 Adding support for FBU05/CVPM06 supercap in MR FW(DCSG00784854
 Assert Audit 7.18: traceTool.py improvements(DCSG00840391
 Update PSoC Bootloader Design in MR FW for PSoC 6(DCSG01107508
 Spell Checking: dictionary improvements(DCSG00906838
 MR SAS Multipath Improvements(DCSG00956036
 Integrate OEM BST scripts to align with mainline BST scripts(DCSG00946945
 Update PSoC MR FW Downgrade Block MFI_STAT to be More Clear(DCSG01155856
 Get controller PSOC version information thru host interface(DCSG00416991
 Add Reboot logs for windows Cache Offload BST(DCSG01074472
 PEX89000: Veloce Cosim Dev BST framework(DCSG01001901
 Atlas2 BST ER: PCIE and SysDMA feature BST Evaluation for COSIM(DCSG01006212
 Snapdump improvement - dump NVRAM key info(DCSG00951413
 Enable MFC Workaround for Sea iMR(DCSG00987792
 Support flash usage above 4 MB(DCSG01006737
 Remove SASPARSER binary from Release Order(DCSG00957868
 Add Firmware Version 10 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01136459
 Run basic Atlas devBST test on Atlas2 RDK(DCSG01003413
 FDE logging improvement: consolidate VKI_PRINTF(DCSG00904945
 Dump code coverage counters on controller reset(DCSG01005809
 SATL : ATA Passthruough command handling when Datalength in MPI < data requested to drive(DCSG00833193
 Create adjusted code coverage reports(DCSG01050388
 iMR Bring-up Effort(DCSG00980238
 MegaAPI_PVT: Move VPD get DCMD from private to public API to Enable end user tools to read custom SN(DCSG00950711
 API change to support PD sanitize operations - overwrite SA(DCSG01006007
 Spell Checking Corrections Part 4(DCSG00712295
 Atlas2 BST ER: Multi host flash boot: create synthetic hierarchy and basic EP and config traffic(DCSG01021605
 Code Space Optimization(DCSG01017044
 SPILIB2: Support for Additional SPI Clock Frequencies(DCSG00424412
 Assert Audit 7.18: remove 17 from raid(DCSG00914508
 Spelling Checking: ONFI corrections(DCSG00735615
(DCSG01082488
 Assert Audit 7.18: merge asserts and adjacent prints(DCSG00904198
 PL SATA : Read logpage 12 and 13 during SATA initialization to get features supported for NCQ encapsulation using FIS porting(DCSG00779724
 API changes to support Multi-LUN / Multi-Actuator : SAS Device only Report as Unsupported Device(DCSG00921455
 Improve a print error message in traceTool.py(DCSG00945787
 Add Sea iMR Firmware Profile Updates(DCSG00980256
 PEX89000: Update Cosim DevBST framework to support launching simulation from outside user shadows(DCSG01093267
 Remove allocation of PCIe devices when NVMe is disabled in NVDATA(DCSG01015478
 XSD : Add New field 'SupportMultiLUN' in MPI2_MR_PARAMS_PAGE_0 to control multi-LUN drive support(DCSG00921459
 SPILIB2: Port all changes AV1 to AV2 for manual access files(DCSG00917802
 Add PERC Signing Build Targets to fwSConstruct(DCSG01071385
 StorCli doesn't show drive information when drive is in Unconfigured Bad or failed state(DCSG00416977
 Add Scons checking for code coverage(DCSG01026819
 PEX89000: Add fancontrol.py and vtmon.py to the common folder of Dev BST(DCSG01004789
 PEX89000: Update BST framework for Linux host and other enhancements(DCSG01062557
 Support downloading of the Host-based Trace Buffer (HTB) via MCTP OOB Interface on Ventura/Aero IOC/HBA (Part A)(DCSG00500554
 Assert Analysis : Refining Read Parameter Logic(DCSG00546986
 Assert Analysis : CDMA Prepare Descriptor Function(DCSG00547825
 Reintroduces the previous security page as MR_MPI26_CONFIG_PAGE_SECURITY_1 to align with current NVDATA(DCSG00977495
 Add Firmware Version 11 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01149460
 Connector Order change for 9502-16e controller(DCSG00966344
 Improve FDE debug code readability with different debug levels(DCSG00417144
 Update Atlas2 A0 Dev BST test cases(DCSG01003416
 PEX89000: Single host MPT BST support on Veloce(DCSG01024714
 Spell Checking: dictionary updates(DCSG00926801
 Block Multi-LUN / Multi-Actuator : SAS Device only Report as Unsupported Device(DCSG00907506
 Spell Checking Corrections Part 2(DCSG00562226
 Add a tool for code coverage(DCSG01000074
 SAS phy port configuration of UBM connected phys based on UBM DFC Link width.(DCSG00927212
 Improve python handling during code coverage builds (MR)(DCSG01040296
 PL SATL : Add SAT translation for the Concurrent Positioning Ranges VPD page(DCSG00927210
 Disable MFC Workaround for Sea iMR(DCSG00987794
 Spell Checking: dictionary management(DCSG00926794
 Sea iMR Bring-up Effort (Part 2)(DCSG00980236
 Remove the Standard IO Header from cache offload module(DCSG00985595
 UBM error handling improvements and debug statistics data collection(DCSG00903198
 Release Automation: automate rebase operation for phase specific streams(DCSG00950531
 Mode Page Improvements for Changeability(DCSG00777318
 Added random number to FTP dir name to prevent signing hang.(DCSG00995197
 Sea iMR Bring-up Effort (Part 1)(DCSG00980231
 Assert Audit 7.18: remove 11 from cfgi(DCSG00914498
 Enhance Atlas1 TS BST to include Buffer ID Support(DCSG00985646
 Add PD_ORDER_MARKER_NVRAM for enhancement DCSG0040(DCSG00834868
 Add code coverage configuration(DCSG01005808
 Spell Checking Corrections Part 3(DCSG00575522
 Update SAS 3.5 FW summary release notes(DCSG00979878
 Add Firmware Version 3 for PartNumber 29211 to PSoC Catalog Image(DCSG01116340
 Add Firmware Versions 27 and 1 for PartNumbers 15987 and 25731 to PSoC Catalog Image(DCSG01166118
 Spell Checking Corrections Part 6(DCSG00963337
 DRAM layout changes for code coverage(DCSG01010648
 Assert Audit 7.18: remove 3 from DM(DCSG00918910
 Add Code Coverage infrastructure(DCSG00981200
 Remove some whitespace from the config page firmware(DCSG00968465
 SPILIB2: Support ECC for Margay(DCSG00429625
 Remove unnecessary assert from code(DCSG00423376
 Enable collection of PCIe Link event "RECEIVED_NAK_DLLP" (EventCode=0x08) by default(DCSG00122084
 Integrate the Atlas BST into CQ(DCSG01011490
 Assert Audit: checked assertion improvements(DCSG00758401
 Improve code coverage statement counting near prints(DCSG01031751
 [Aero] Enable UBM detection logic on all connectors for OEM HBA with SEP_PRESENT GPIOs(DCSG00927207
 Spell Checking Corrections Part 5(DCSG00734528
 Sea iMR Bring-up Effort (Part 1-2)(DCSG00986031
 Add Vision sources to cpld_src(DCSG01082289
 Blackduck: Remove non UTF-8 encoding characters from source files(DCSG00258258
 Add 9502-16e board Nvdata to Aero ROP(DCSG00966467
 Update BinToRom for Multiple PSoC Images(DCSG01063758
 Release Automation: Update scripts for FW Ph21(DCSG01008758
 Create Partial XML for 9502-16e HBA(DCSG00930106
 Snapdump Enhacement - SES Module(DCSG00952775
 NVRAM Dynamic sections needs to be cleared during CTRL REPURPOSE(DCSG00408254
 Spell Checking: checkSpelling.py improvements(DCSG00746454
 Release Automation: Check for failure during baseline creation(DCSG00958012
 PL SATL : Update the WRITE SAME command to account for Zoned Block Devices(DCSG00500552
 Spelling Checking: COL corrections(DCSG00734457
 Add OEM build action to SCONS(DCSG00996371
 Add XSD files for Sea iMR(DCSG00980244
 MegaAPI: Add API changes for blocking import on JBOD (def: 1030129)(DCSG01035264
 Clean up inline functions(DCSG00984425
 Add Firmware Version 12 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01159010
 Q-depth optimization to improve read performance for R10 and other array configurations with spanned arms(DCSG00914358
 Add Firmware Version 8 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01130658
 Assert Audit: add snprintf, vsnprintf(DCSG00735103
 Enable Slavebypass Error interrupt for Sea iMR(DCSG00987773
 SPILIB: Add support for Hybrid topology CFI parts(DCSG00782279
 SPILIB2: Add serial mode support for SPI devices with read only Quad Enable bits. Add hybrid dual mode support.(DCSG00916467
 Atlas1 VS BST deployment(DCSG00985647
 Improve python handling during code coverage builds (fw_bld_tools)(DCSG01040300
 PEX89000: Add multiple SPI device access devBST tests on SPI1(DCSG01003417
 MR7: Block Out-of-Order insertion of drives during Foreign Import with Pinned entries(DCSG00405605
 PEX89000:Veloce Cosim Dev BST error counter testcase(DCSG01006209
 secureSignBin: implement feature to download the public key during signing or with explicit arg(DCSG01035866
 Enhance out of order insertion feature to support R1 & R10(DCSG00903546
 PL : Remove obsolete workarounds(DCSG00008204
 DM Error code handling - UA / SES Inquiry after Expander micro code update.(DCSG00231452
 Move to the latest mbed_tls version which is 2.26.0(DCSG00966339
 Support streaming of debug logs (HTB) via I2C OOB band on Ventura/Aero IOC/HBA (Part B)(DCSG00927213
 LD Secure Erase and Progress Reporting(DCSG00931395
 Spell Checking(DCSG00547922
 secureSign add support for -sha2 passthrough to signImageX and updates to secureSignSPDM for NIC board team(DCSG00977399
 Add Atlas2 A0 devBST for automatic CQ launch(DCSG01003423
 SPILIB: Update build scripts for ADS(DCSG00943761
 Enable DASEP detection on SASA for Adapters(DCSG00983302 (Port Of EnhancementRequest(DCSG01071382)
 Bad Phy detection logic improvement(DCSG00932841 (Port Of EnhancementRequest(DCSG00977228)
 Update ControllerInfo Structure with PartNumber(DCSG01063757 (Port Of EnhancementRequest(DCSG01074470)
 Disk labels need to be tied to fixed physical ports in order(DCSG00240927 (Port Of EnhancementRequest(DCSG00966521)
 Workaround to block UBM I2C traffic while flashing MR FW(DCSG00836954 (Port Of EnhancementRequest(DCSG00838610)
 Enable DASEP detection on SASA for Adapters(DCSG00983302 (Port Of EnhancementRequest(DCSG00990994)
 Disk labels need to be tied to fixed physical ports in order(DCSG00240927 (Port Of EnhancementRequest(DCSG01015974)
 Passthrough Support for Vendor Specific NVMe Opcode D9h and C0h(DCSG01128891 (Port Of EnhancementRequest(DCSG01151746)
 Extending SnapDump Persistence(DCSG00247000 (Port Of EnhancementRequest(DCSG01015971)
 Create new profile with only SAS/SATA drive support for new controllers for DASEP backplanes(DCSG00991280 (Port Of EnhancementRequest(DCSG01070765)
 Change locking mechanism for OEM(DCSG00543073 (Port Of EnhancementRequest(DCSG00861750)
 OEM Adapter FW assertion after flashing 16MB Image (Clean Flash)(DCSG00989390 (Port Of EnhancementRequest(DCSG00991778)
 cryptographic erase for ISE drives is supported on sysPDs disks(DCSG00552703 (Port Of EnhancementRequest(DCSG00775569)
 SEKM feature enhancements to handle error scenarios(DCSG00777328 (Port Of EnhancementRequest(DCSG00903186)
 NVMe Passthru command support(DCSG00432879 (Port Of EnhancementRequest(DCSG00966518)
 Enhance Error scenario handling in SEKM Feature code(DCSG00966411 (Port Of EnhancementRequest(DCSG00974796)
 Add PSoC Image Checking and MR FW Blocking(DCSG01064530 (Port Of EnhancementRequest(DCSG01074471)
 Host SES access and management of backplanes should not be allowed.(DCSG00974114 (Port Of EnhancementRequest(DCSG00995207)
 Sea iMR CBB Updates(DCSG00980247 (Port Of EnhancementRequest(DCSG01032931)
 LKM compliance to Cryptographic Algorithm Requirements v1.5(DCSG00830702 (Port Of EnhancementRequest(DCSG01015968)
 Extending SnapDump Persistence(DCSG00247000 (Port Of EnhancementRequest(DCSG00966519)
 SEKM Support for IT controllers(DCSG00433132 (Port Of EnhancementRequest(DCSG00777312)
 Remove Retries When INQUIRY for Extended VPD Page 86h Returns 5/24/00(DCSG00922081 (Port Of EnhancementRequest(DCSG01015964)
 Error handling of UBM CHANGE_DETECT# signal(DCSG00962565 (Port Of EnhancementRequest(DCSG00963253)
 [SPDM] Blocking slots 1-7 from configuring SPDM certificates(DCSG00500296 (Port Of EnhancementRequest(DCSG00507210)
 Do not generate "Bad Phy" event for NVMe drives that fail NVMe Init(DCSG00543046 (Port Of EnhancementRequest(DCSG01070337)
 Pinned Cache: In legacy BIOS mode, if pinned cache is present, do not boot to OS(DCSG00366448 (Port Of EnhancementRequest(DCSG00915777)
 [Aero][PLDM] Platform changes to accommodate latest PLDM baseline(DCSG00447989 (Port Of EnhancementRequest(DCSG00500775)
 MR FW Need a smooth and authenticated method to transition from LKM to EKMS (SEKM)(DCSG00318546 (Port Of EnhancementRequest(DCSG00432105)
 SEKM: Prevent firmware Download of firmware that do not support SEKM when SEKM is enabled.(DCSG00549524 (Port Of EnhancementRequest(DCSG00816022)
 NVMe Passthru command support(DCSG00432879 (Port Of EnhancementRequest(DCSG01015970)
 Remove Retries When INQUIRY for Extended VPD Page 86h Returns 5/24/00(DCSG00922081 (Port Of EnhancementRequest(DCSG00966515)
 Create new profile with only SAS/SATA drive support for new controllers for DASEP backplanes(DCSG00991280 (Port Of EnhancementRequest(DCSG01069429)
 Do not generate "Bad Phy" event for NVMe drives that fail NVMe Init(DCSG00543046 (Port Of EnhancementRequest(DCSG01070769)
 Update and Add PSoC Image Building Batch Files(DCSG01063756 (Port Of EnhancementRequest(DCSG01074467)
 LKM compliance to Cryptographic Algorithm Requirements v1.5(DCSG00830702 (Port Of EnhancementRequest(DCSG00966516)	


Version 51.17.0-4094 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:7.17.00.0
	UEFI Driver:0x07110200
	HII:07.17.02.01
	MR FW: 5.170.00-3532
    package 51.17.0-4094
MR 7.17

Defects:
-PL SATA Only : SATA PFA drive is not recognized as PFA drive in Aero while hot-plugging(DCSG00427743)
-Native Hidden VDs become Unhidden VDs after rebooting and doesnt clear clean shutdown flag in DDF(DCSG00422736)
-Assert Audit: remove 2 related to NVME(DCSG00425107)
-Some drives and enclosures not added to Windows OS when SAS/SATA devices are reduced in NVDATA.(DCSG00654062)
-MR7.16: R1 VD showing WJ messages with Pinned cache.(DCSG00379794)
-Enable planned virtual drive removal feature using NVdata(DCSG00412149)
-Aero MR7.16 Alpha - Typos streamDetectec in crashdump.txt with commands pending debug(DCSG00370205)
-[NVMe] Firmware download in mode E failed with error Invalid Firmware Image(DCSG00313245)
-[Code Review] Updated CoreDump related data structures to have capitalized first letter for the member fields(DCSG00250948)
-Aero MR7.17 Alpha - Missing ME Events on PD during recovery(DCSG00707151)
-[NVMe] Send diagnostic to abort background test completes with success when no background test started.(DCSG00310330)
-SPDM IT:SPDM BMC bring up on P2 server(DCSG00238540)
-Aero MR 7.17PA - After SMC legacy bios boot message, snapdump content is missing(DCSG00412164)
-MR 7.16 Alpha: Uart Typo(DCSG00358488)
-Fix invalid Enclosure ID for NVMe drives that failed init after Atlas only power cycle(DCSG00418131)
-Initiate OOB FW download on the Ctrl while flashing the FW from in-band led to Exception mon_task(DCSG00431713)
-Aero MR7.17PA2 - NVMeFailedDrives still listed after Atlas enclosure is powered off(DCSG00513680)
-Assert Audit: remove 4 related to memory allocation(DCSG00429630)
-RDE - Firmware is not logging "WriteCacheDataLoss" RDE alert(DCSG00316889)
-MR 7.16PA1: Assertion failure in fw\hw\ioa\ioDivertHw.c at line 340: newVal >= 0(DCSG00321422)
-Aero: PL with newer Atlas FW (4.2) has extra slot number in the Atlas enclosure(DCSG00284238)
-Format Repair operation fails on certain NVMe drive(DCSG00408635)
-IML error code 0x1945 logged on every boot without any drives connected to controller(DCSG00315354)
-[NVMe] Protect bit is always set in standard inquiry data for NVMe drives.(DCSG00301661)
-Assert Audit: remove 1 related to Preboot(DCSG00500238)
-[NVMe] SCSI TUR command fails when sent to a NVMe drive with corrupted LBA 0(DCSG00299624)
-Blocking SAS Link Speed change for unconnected PHYs(DCSG00779179)
-MR7.16 Alpha: Deletion of VD's with Pinned WJ on WT VD's causes firmware to crash(DCSG00394228)
-4K Rand write test got poor performance from 4 drives RAID5 unexpectedly(DCSG00918259)
-Flash failed and flash degraded RMA's(DCSG00362663)
-Aero MR 7.16PA - Typos in crashdump.txt and TTY "Outstadning IO list"(DCSG00354205)
-[NVMe] Mode Select command to write Read Write Error recovery page fails.(DCSG00307175)
-[VSes] Connector name of the VSes device in SAS device page 0 has invalid data if no device is connected to port 0(DCSG00383998
-MR 7.16 - FW hit Exception mon_task when rebooting with pinned_cache(DCSG00324739)
-Fix unnecessarily generated fatal event in status process for unlock PD(DCSG00378774)
-[Aero] Phase 18 build error fix(DCSG00708175)
-Aero MR7.17PA - Duplicate entries in nvme init error list after drive pull/push(DCSG00408157)
-Hibernate with rebuild result to PL Fault on 9440-8i controller(DCSG00776334)
-Fix FW hang on MR 416i/216i controllers when EKMS is enabled(DCSG00434047)
-MR 7.16 Beta: Firmware is not handling unpinned WT interrupted writes for LDs that are missing/offline during bootup(DCSG00409426
-Fix for allowing offline VD to be set as bootdrive(DCSG00925005)
-pl: NVMe: status code type not checked upon Write Buffer callback(DCSG00419779)
-Aero MR 7.17PA - Snapdump assert only shown in PTB file, add to UART and other logs(DCSG00420417)
-Fixed coverity defects.(DCSG00258253)
-Customer: Found "C0: Dumping poll data. total length = 3, objtype 0", these message coming to uart firmware log continuously after update BMC(DCSG00349880
-Fix Controller hang after snapdump generation in Legacy BIOS pre-boot(DCSG00342843)
-MR 7.16 Beta: RMW assertion on Q Parity with Pinned WJ(DCSG00408663)
-RDE - REST client displays junk character at the end of drive firmware revision(DCSG00306782)
-Coverity found defects for converting an expression to a narrower type in SATL code.(DCSG00297461)
-PL fault: Invalid Msg Frame fault triggered on external card connected to UBM BP(DCSG00408493)
-[VSes] SCSI State not correctly set for some error response to SCSI commands.(DCSG00312554)
-[NVMe] Extended Self Test Completion time in Control mode page is byte swapped(DCSG00308453)
-RDE - REST client displays ServiceLabel property of storage resource as Slot= instead of Slot (DCSG00306804
-BST Failure: 7.16 Sanitize Changes Break Dev BST(DCSG00311542)
-Update EOS token checking for Ruby drive(DCSG00332811)
-pl: NVMe: async event handler proceeds during IO quiescing(DCSG00431716)
-Relax reboot required for PTB and Snapdump properties(DCSG00487206)
-Element Status code of a Slot in SGPIO BP with no drive marked as 'Unknown'(DCSG00428815)
-MR 7.16 Alpha: KA observed after many loops of cable push/pull to enclosures(DCSG00365625)
-MR 7.17 PA1: Unable to change bios mode through storcli(DCSG00420496)
-Aero MR7.16: Moved NVRAM debug mprintf to etprints.(DCSG00336300)
-pl: SAS IO Unit Page 1 Write Current may not cause phy to be enabled(DCSG00654031)
-Add SSD Wear Gauge statistics reset to begin with(DCSG00415054)
-[NVMe] TSD bit not getting set in Reference Temperature log parameter(DCSG00430063)
-MR 7.16A controller continuously dumps unexpected sense 7/20/02 for a Jbod and the drives cannot be erased.(DCSG00363682
-Fix Patrol read exclusion behavior for non-EPD HDD VD(DCSG00313121)
-Update SBLIB version in BST version file(DCSG00316342)
-MR7.17-Assertion failure in fw\raid\cache.c at line 4379: while de-staging pinned WJ(DCSG00500757)
-Update the Driver Trigger Page data structs' size and add padding to make them 256 bytes(DCSG00258095)
-Scrutiny Aero failed at Run Eyescope as "Initialization failed, EyeScope will not run!" while connecting Aero to Atlas.(DCSG00362708
-Performance drop of 5-9% seen with Random Read/Write IOs to NVMe drives.(DCSG00258412)
-MR 7.16 Alpha FW PK 3644 changes Disk order in Windows Disk management and makes a VD insonsistent which was not pinned.(DCSG00358927
-[SPDM IT] Return actual size of certificate chain content to SPDM LIB(DCSG00233805)
-Fix Coverity issues(DCSG00293500)
-fix typo(DCSG00433182)
-MR_7.16_DBU_PA1: EPD's lost after test configuration upgrade from 7.15 to 7.16(DCSG00311528)
-NVMe : PROTECT bit in inquiry data is set.(DCSG00308451)
-pl: Incorrect c0 values displayed for SAS/SATA in the "pl serdes tx" output(DCSG00422289)
-Fix a print statement related to region lock(DCSG00433052)
-fix unnecssary print messages(DCSG00751354)
-RDE - Fix OEM reported observations(DCSG00333013)
-MR_7.17_PA1_DBU:ERROR- Exception Handler Called for Processor Core = 0 during OnDemandSnapDump IOCTL fire on Ventura IMR(DCSG00426994
-Controller hang is observed during system reboot(DCSG00547412)
-Assertion failure in fw\raid\fwDownload.c at line 1182 observed, while downloading the Atlas FW in "Atlas Behind Aero" configuration(DCSG00354677
-RDE alerts are not logged for predictive failure drives on AROC controllers(DCSG00316767)
-Aero: HW Workaround - When Aero is in the L1 state it periodically (every 2 ms) transitions to L0 and back to L1(DCSG00501537
-VSES getting removed in OS on controller reset.(DCSG00301631)
-Update coverity.conf(DCSG00405664)
-Aero MR7.16PA - NVMe PDs use sanitize path for /c0/ex/sx start erase crypto but FW and storcli report NO for sanitize support(DCSG00352790
-Address review comments of CSET DCSG00335901 and cleanup for Defect DCSG00325884 fix(DCSG00369965)
-After running a Media error injection script on VDs overnight, CC not progressing until after a reboot(DCSG00299417)
-[Aero] SAS SATA only partial nvdata xml are not included in release order.(DCSG00394146)
-Assert Audit: remove 2 related to memory allocation(DCSG00427605)
-RDE - Change the format of command header ETag(DCSG00417320)
-Energy pack failure events logged twice by firmware(DCSG00345394)
-[NVMe] Mode select command to set Control Mode page with last two bytes changed completes successfully.(DCSG00315331
-Firmware event format of failed NVMe drive is not as per OEM's requirement(DCSG00321894)
-PL Backend PCIe : SATA drive discovery is delayed(DCSG00310045)
-MR7.16 PA1: Missing punctuation in HII Critical message Number of disks exceeded the maximum supported count(DCSG00315797
-MR 7.17_SLT: PD erase shows success for the enclosure(DCSG00547453)
-Coverity issue(DCSG00293875)
-RDE - REST client display for drive model number of specific NVMe drive is not in sync with host application output(DCSG00330586
-MR 7.17 PA1: Controller encountered an error and was reset during cable pull/push test(DCSG00417818)
-RDE - REST client displays "HotspareType" as "Chassis" for a dedicated hotspare drive(DCSG00404756)
-MR 7.16 Alpha: Error when trying to stop erase on a SATA ISE SSD(DCSG00370489)
-WJ dev defect - Remove extra init_cache in RecoverPinnedWJandRMWForLd(DCSG00369213)
-Ring buffer decoder GUI hangs if timestamp is invalid(DCSG00437238)
-MR 7.17 PA1: During Patrol Read Kioxia NVMe drives reporting sense data 3/11 media errors with no LBA info(DCSG00427380
-pl: NVMe: chain to PRP SGL for non-read/write IO may be handled improperly(DCSG00408313)
-Enclosure insertion event does not display controller port information(DCSG00299141)
-Assert due to ptbPrintf(DCSG00335823)
-[NVMe] Inquiry command to NVMe device reporting old rev firmware after drive firmware update completed successfully(DCSG00321504
-RDE - DriveInserted RDE alerts are generated when pause for boot time password is enabled on the controller(DCSG00347569
-Assert Audit: remove 6 from the PTB feature(DCSG00405628)
-Ventura/Mercator: pl: direct attached SAS or SATA device may not be discovered(DCSG00408109)
-Fix Coverity tool reported defects(DCSG00266266)
-Aero Core0 exception during Atlas sg_write_buffer enclosure FW update(DCSG00380775)
-Assert Audit: remove 1 from drive spinup(DCSG00405647)
-README file mentions sas2parser instead of sasparser(DCSG00394150)
-PL SNTL : Accumulated Power On Hours value reported by LogSense translation is byteswapped(DCSG00499729)
-MR7.17PA: Add additional debug to help debug unexpected TRANSIENT buffer(DCSG00422398)
-MR 7.17- DC with outstanding RMW commands on 16 drive R6(DCSG00427249)
-No warning message to inform user about lost cache when the BBU missing(DCSG00480562)
-MR 7.17 PA1:Media errors not detected on NVMe drive with VERIFY command supported(DCSG00414020)
-Shim layer is returning ERROR for successful FW image flash.(DCSG00707632)
-[Ventura] Some NVMe drives are not discovered(DCSG00301612)
-Data abort while running Single glitch COL test: Exception due to executing THUMB instruction 0x6008 at address 0x7f83b9ac(DCSG00920924
-RDE - REST client display for drive revision number of specific NVMe drive model is not in sync with host application output(DCSG00330589
-MR 7.16 PA2: Uart printing typo(DCSG00348407)
-System hung with FW exception during COL Single dip test(DCSG00359647)
-MR 7.16PA2-WJ entries are not being discarded for R1 VD's.(DCSG00344241)
-RDE - Drive encryption status should be shown as "Foreign" in REST client after drive pull/push of a FDE drive participating in a secured volume(DCSG00261286
-Port name information is missing for SATA drive insertion and removal events(DCSG00261173
-fix key signature mismatch due to wrong compare length.(DCSG00384375)
-[NVMe] Send diagnostic with self test bit 1 but selftestcode non 0 is not failed.(DCSG00306498)
-Move Version control files to folder for Release BST(DCSG00342866)
-Force Ruby support to Disabled for 7.16(DCSG00827991)
-MR7.16 PA2-Drive are coming up foreign when they should be doing a copyback after system reboot(DCSG00358558)
-StorCLI set OOB MaxPayLoadSize to 576 but after rebooting it changed to 64(DCSG00415578)
-Add a print to identify PTB merges(DCSG00328310)
-Aero 7.16PA - Storcli erase crypto to WD SAS SSD results in timeouts and core0 exception(DCSG00350404)
-RDE - REST client displays RAID1 with 8 drives as RAID1E instead of RAID10(DCSG00253778)
-Fix ETTY compression with initPrintf statements(DCSG00398152)
-MR 7.16 Data corruption after pinned cache and OCR on every block.(DCSG00352925)
-Update EOS token checking for Opal drive(DCSG00348250)
-Remove .text from symbol_dump.txt in Snapdump(DCSG00334539)
-Fixed PH17 Coverity issues(DCSG00335212)
-[NVMe] PL Fault 0xE429 is seen while performing reset for certain NVMe drive.(DCSG00395750)
-MR7.16PA2-WB vd stays WT/NORA after Pinned WJ(DCSG00349052)
-Aero 7.16PA: Undo NVRAM section forward migration fix.(DCSG00352663)
-No power source was found for the memory during 48 hour Single glitch COL test(DCSG00831482)
-Enable ekms option is getting enabled in HII(DCSG00543363)
-Fix Opal function to relock PD(DCSG00409615)
-LSA MR 7.17: Under Raid Personality Mode, Changing the Behavior mode to R0 is not getting changed.(DCSG00422218)
-Observed fatal FW error at Line 169 in fw\raid\utils.c on drive removal in a 240 VD configuration.(DCSG00394143)
-MR 7.17: Changing the behavior mode to RO from None, is not making the UGOOD PDs as RO VDs in the presence of the PD with Prepare for removal state .(DCSG00758604
-[Ventura][NVMe] Phy disable from application does not removed the drive from PL.(DCSG00384856)
-Aero MR7.16PA - Linux driver remove/load test reproduces controller fault and snapdump on Aero NVMe config(DCSG00312316
-Controller hits assertion failure after importing VD with pinned cache and resuming I/O(DCSG00758169)
-Uninitialized pointer access in UBM code.(DCSG00446918)
-MR 7.16 PA1: uart printing errors(DCSG00313340)
-Address Coverity issues(DCSG00263385)
-iMR 7.16 Ventura controller, LED of every drive keeps blinking on Unconfig good drives and Online drives.(DCSG00382409
-RDE - Stale drive data is accessible post drive removal and inserting a new drive(DCSG00258251)
-Aero MR7.16PA - Assertion failure in fw\dm\src\dm.c at line 2034 during SAS/SATA/NVMe UGOOD crypto erase(DCSG00342612
-Allow LKM to EKM switching from HII(DCSG00808130)
-DM NOT completing the device discovery(DCSG00339945)
-Unblock Sanitize Passthrough for JBOD on MR 216/416 controllers(DCSG00431924)
-MR7.16-DC with 16 Drive WB R5 pinned cache(DCSG00536516)
-Vision PSoC info prints added in Serial output for MR216i(DCSG00382714)
-Fix coverity reported defects(DCSG00282926)
-RDE - State property for Persistent Cache displays empty in REST client when energy pack is in charging state(DCSG00247993
-[NVMe] Parameter Code in Self Test Results log page is incorrect.(DCSG00422250)
-Able to import PD after FW treats VD/PD missing for RLM as Critical (OCR case)(DCSG00258652)
-Add missing CCR registers to Snapdump(DCSG00344073)
-Aero MR 7.17 - CLI reports success for /c0/fall delete operation of foreign locked VD(DCSG00405003)
-fix the issue that WT cache did not get initialized before LD config is removed due to drive removal(DCSG00340135
-MR7.17PA2: Autoconfig mode not reset to default on set factory command(DCSG00507799)
-MR 7.16PA2: FW continuously prints C0:In OOBExecCmdIssue and dmcd is 0x1010000 on customer controller(DCSG00324215)
-Complete degraded LD list was not getting printed in the UART(DCSG00312959)
-Assert Audit: add a new memory allocation interface(DCSG00420016)
-AXI access errors causing FW asserts or faults due to invalid SATA passthrough commands(DCSG00215338)
-Remove trailing whitespace from prints(DCSG00397411)
-Fix macro parsing in traceTool.py(DCSG00433056)
-Avoided the unknown IML event is getting generated.(DCSG00549320)
-OEM: OOB SLT returns error 0x7004 when run SelfCheckingDiagnostic option(DCSG00352769)
-Make firmware build compilable without PLDM folder(DCSG00299709)
-MR7.16PA2- rename API in the FW code(DCSG00335548)
-Flashing PD FW under I/O over OOB led to Exception mon_task(DCSG00408861)
-Fix SSD Wear Gauge data for SAS/SATA(DCSG00286608)
-RDE - REST client displays incorrect value for "LanesInUse" property of storage resource(DCSG00312188)
-Assert Audit: minor changes from 11/11 review(DCSG00424116)
-WJ dev defect - WB vd stays WT after pinned cache deletion, WT LD pinned cache bitmap is not cleared(DCSG00351776)
-pl: backend PCIe: fix a couple of issues related to PCIe discovery and NVMe init(DCSG00355408)
-Assert Audit: remove 1 related to configuration DCMDs(DCSG00431549)
-NVMe Repair Operation hangs on a certain NVMe drive with Multiple Namespace(DCSG00415462)
-RDE - Controller serial number is inconsistent between device inventory and storage page(DCSG00427599)
-Fixing import issue for RAID 5/6 WT Secure VDs after entering boot time password in presence of pinned Write Journals(DCSG00321918
-Release Automation: If release job web page takes more than 60 secs to load, script throws exception(DCSG00297363)
-MR7.16PA2-25 drive R5 is causing Assertion failure after pinned cache(DCSG00350580)
-Sanitize command support - Code review AIs and cleanup.(DCSG00378002)
-MR 7.16 Alpha: Restore operation expected but not started message during COL double dip test with VDs in WT mode.(DCSG00383573
-Fix wrong ComID got assigned at drive type detection(DCSG00311877)
-MR 7.16 Alpha: Uart printing(DCSG00384374)
-Medium Errors Not discovered during copyback(DCSG00734524)
-MAC verification failed due to inconsistent secure ID(DCSG00309854)
-Aero MR 7.16: discardCacheDuringLDDelete bit is not set(DCSG00369044)
-Disallow the request to update SAS link speed /PCie lane speed for UBM backplanes.(DCSG00371417)
-Assertion failure in fw\cpu\arm\exceptions.c at line 1006: 0 while running IOs in large config(DCSG00423087)
-MR7.16: Setting Patrol Read exclude SDD VD is not working(DCSG00378708)
-Update build scripts to map PLDM debug strings from flash to BSS section(DCSG00298667)
-Device order boot message is issued on next server reboot after performing purge operation(DCSG00541268)
-Fix data definition discrepancy between API and MR FW.(DCSG00383503)
-Remove OEM PNPID checks for sg_utils sanitize PR,(DCSG00319704)
-MR 7.16 PA2: Uart printing errors(DCSG00323893)
-SnapDump should not contain sensitive data(DCSG00335397)
-MR 7.17-DC with 4 drive R5 RMW pinning(DCSG00398245)
-Revert NVSRAM Dynamic section DST_CTRL_PROP_NVRAM changes and Use NVSRAM Static memory area faultData region) to store MR_CTRL_PROP2 copies.(DCSG00347855
-Fixed dynamic SSD wear gauge updating mechanism(DCSG00254753)
-RDE - Move dictionaries from flash to DRAM section(DCSG00263549)
-MR 7.17 Alpha: After OCR where drive is pulled during OCR, controller comes back in safe mode even though VD should only be degraded(DCSG00557518
-Aero MR7.16PA - snapdump hang during capture in Legacy BIOS(DCSG00318700)
-Assert Audit: fix typo(DCSG00418053)
-SPDMIT: Return appropriate error to SPDM Lib when read certificate from security page 0 fails(DCSG00299079
-[NVMe] The long LBA bit is not set in Mode Parameter header.(DCSG00319580
-Virtual drives offline during Ibanez HBA firmware upgrade/downgrade test using storcli(DCSG00343804
-MR 7.17 PA1: Excessive prints in etty log(DCSG00408200
-Adjust I2C CLK frequency on all the controllers(DCSG00421120
-EKM to LKM security mode transition is blocked.(DCSG00654089
-MR FW exception handler called when trying to discard pinned cache after failed attempt to import foreign config(DCSG00420456 (Port Of Defect DCSG00552664)
-PL Fault 0xEA11 observed, while upgrading Atlas FW using StorCLI in presence of bad NVMe PD's present in the Atlas.(DCSG00324838 (Port Of Defect DCSG00340935)
-[Aero] Controller missing in System Bios.(DCSG00411545 (Port Of Defect DCSG00420098)
-SATA Only: Command timeout observerd on SATA drives(DCSG00344039 (Port Of Defect DCSG00356008)
-Phy bad events are logged when Exp phyop is disabled(DCSG00428690 (Port Of Defect DCSG00521372)
-Observed PL Fault 6231 while running IOs along with Expander phy link reset.(DCSG00363807 (Port Of Defect DCSG00373461)
-Device add/remove event sent with wrong enclosure handle in certain multi VSes topology.(DCSG00350248 (Port Of Defect DCSG00380548)
-During OS reboot some drives go missing.(DCSG00354770 (Port Of Defect DCSG00361759)
-Kill adapter seen on multiple EPDs with IOs with TMs(DCSG00923995 (Port Of Defect DCSG00959011)
-LSA MR 7.17: Under Raid Personality Mode, Changing the Behavior mode to R0 is not getting changed.(DCSG00422218 (Port Of Defect DCSG00543346)
-Enclosure ID of some Switch attached NVMe devices missing after system reboot.(DCSG00414735 (Port Of Defect DCSG00426692)
-[3508 + MR7.14] Controller failed into ERROR: Exception Handler Called for Processor Core = 1 and Waiting for OCR is seen with Fatal firmware error: Line 169 in fw\raid\utils.c(DCSG00953878 (Port Of Defect DCSG00959993)
-Flashing PD FW under I/O over OOB led to Exception mon_task(DCSG00408861 (Port Of Defect DCSG00552878)
-Data abort while running Single glitch COL test: Exception due to executing THUMB instruction 0x6008 at address 0x7f83b9ac(DCSG00920924 (Port Of Defect DCSG00923772)
-Extra ldbbmBadListAdd print was seen during ldbbm update(DCSG00344606 (Port Of Defect DCSG00349552)
-4K Rand write test got poor performance from 4 drives RAID5 unexpectedly(DCSG00951753 (Port Of Defect DCSG00960458)
-ParentDevHandle value calculated for given Phy Number is incorrect for Direct Attached Devices in Event Replay logic(DCSG00299632 (Port Of Defect DCSG00299823)
-SEKM secured NVME OPAL drives over a warm reboot will lock and require the SEKM key.(DCSG00241201 (Port Of Defect DCSG00311638)
-Nested RAID level performance improvement(DCSG00903237 (Port Of Defect DCSG00916849)
-MR7.18_Alpha:Foreign import from Mutli Span/LD drive with other drives cause, FW crash and import failure(DCSG00949516 (Port Of Defect DCSG00960587)
-[SATA ATAPI] FW fault 0x6231 seen while completing some IO for ATAPI device.(DCSG00350047 (Port Of Defect DCSG00353918)
-FW halts when "ubm show " is triggred(DCSG00312896 (Port Of Defect DCSG00932985)
-[MR3508+MR7.14 +X86 ] Controller is seen with Fatal error by unknown reason unexpectedly (XH628 V5's 3508 mem.c issue)(DCSG00312708 (Port Of Defect DCSG00316967)
-PL : Missing drives during AC power cycle test(DCSG00275868 (Port Of Defect DCSG00301823)
-Parallel PD FW download should not be allowed in OOB I2C mode(DCSG00935499 (Port Of Defect DCSG00935546)
-MR FW changes to Revert NVSRAM Dynamic section DST_CTRL_PROP_NVRAM changes and Use NVSRAM Static memory area faultData region) to store MR_CTRL_PROP2 copies.(DCSG00347965 (Port Of Defect DCSG00349563)
-NVMe Init error drives are not discovered after pull/push within DMD timeout(DCSG00242197 (Port Of Defect DCSG00250023)
-SCSI Compliance 2.0 Failure ASSERTION: VERIFY (16) Exceed Capacity Test(DCSG00957057 (Port Of Defect DCSG00960565)
-SATA only: WRITE SAME NCQ encapsulation assumes NonData NCQ is supported if Zero EXT is Supported(DCSG00398894 (Port Of Defect DCSG00412030)
-Controller hits assertion failure after importing VD with pinned cache and resuming I/O(DCSG00758169 (Port Of Defect DCSG00834149)
-Make Clear of the PEPP version of ConfigValid Applicable to IT Boot Code Only(DCSG00398453 (Port Of Defect DCSG00404468)
-MR FW exception handler called when trying to discard pinned cache after failed attempt to import foreign config(DCSG00420456 (Port Of Defect DCSG00552663)
-NVMe Init Error: Device with no namespaces shows 'Namespace count Invalid' as Unrecoverable Error(DCSG00290593 (Port Of Defect DCSG00303510)
-RDE - WriteCacheProtected RDE alert getting generated across reboot/OCR without any changes in battery state(DCSG00355897 (Port Of Defect DCSG00383420)
-PL NVMe : PCI task management is not getting completed.(DCSG00231422 (Port Of Defect DCSG00266053)
-Combination of Expander FW update and OOB inventory commands leads to Data abort exception.(DCSG00417301 (Port Of Defect DCSG00521370)
-HII Refresh Topology Hangs when connected to Faulty SES Device(DCSG00385938 (Port Of Defect DCSG00404446)
-System bios hangs during initial drive discovery.(DCSG00312551 (Port Of Defect DCSG00382416)
-SHIELD state transition prints for PDs that are not installed on the system when a clear config is run with a rebuild running.(DCSG00454025 (Port Of Defect DCSG00543479)
-(SATA Only) IO Timeouts seen while running Unmap, SATA Passthrough and Read/Write IOs to a SATA drive(DCSG00654439 (Port Of Defect DCSG00831921)
-StorCLI set OOB MaxPayLoadSize to 576 but after rebooting it changed to 64(DCSG00415578 (Port Of Defect DCSG00552845)
-Delayed response while application firmware and IOs running(DCSG00759013 (Port Of Defect DCSG00835563)
-Code changes to compare buffered Enclosure status page 02 needs to be removed.(DCSG00314803 (Port Of Defect DCSG00651595)
-[Aero][UBM] Enhance the link configuration to handle the link speeds for SAS/SATA drives behind UBM.(DCSG00552897 (Port Of Defect DCSG00706402)
-FW halts when "ubm show " is triggred(DCSG00312896 (Port Of Defect DCSG00521366)
-PL: 9460-16i incorrect slot numbers assigned attaching to OEM specific mixed mode backplane(DCSG00243953 (Port Of Defect DCSG00342787)
-Assertion failure in fw\cpu\arm\exceptions.c at line 1006: 0 while running IOs in large config(DCSG00423087 (Port Of Defect DCSG00543477)
-Serdes TX table in pl diag dump has the Pre-cursor, Post-cursor and Attenuation values mixed(DCSG00388268 (Port Of Defect DCSG00404448)
-Bad phy events are generated continuously after staggered hotplugging of bad drives in UBM backplanes(DCSG00405552 (Port Of Defect DCSG00579741)
-9460-8i faults repeatedly at fw\raid\utils.c(DCSG00265811 (Port Of Defect DCSG00334585)
-Dev-defect: WRITE with a transfer-size of 0 results in a hang.(DCSG00380906 (Port Of Defect DCSG00415495)
-Ventura: SAS3616W or SAS3616W based boards have links less than epected width(DCSG00249594 (Port Of Defect DCSG00249753)
-OEM server Raid self diagnostic test fails test when the system has Raid but no HDDs(DCSG00830628 (Port Of Defect DCSG00832446)
-9500-16e disappears on system reboot(DCSG00367091 (Port Of Defect DCSG00414022)
-Storage controller goes through repeated resets and is not discovered by host(DCSG00943829 (Port Of Defect DCSG00948302)
-Controller fault observed on changing some phys to manual port config with port set to 0.(DCSG00237498 (Port Of Defect DCSG00245531)
-Controller Faults when connected to DA SEP Backplane(DCSG00916381 (Port Of Defect DCSG00918084)
-Aero A0: Controller faults 0xD015 with Refresh topology from BIOS in a managed PCIe switch config.(DCSG00414714 (Port Of Defect DCSG00418238)
-Modify DPN for particular battery type(DCSG00340940 (Port Of Defect DCSG00342271)
-[Aero][PLDM] Date format exposed by IT to PLDM library is not as per PLDM spec(DCSG00363642 (Port Of Defect DCSG00398739)
-Fix a print statement related to region lock(DCSG00433052 (Port Of Defect DCSG00566794)
-[VSes] Element status set to 'Unknown' in SES page 2 of VSES for some phys where nothing is connected.(DCSG00333163 (Port Of Defect DCSG00343848)
-Add support back for NVMe opcode 0x4 (write uncorrectable error)(DCSG00427402 (Port Of Defect DCSG00500131)
-Snapdump logs are getting lost during OCR(DCSG00426286 (Port Of Defect DCSG00543344)
-FW assert is observed while performing JBOD to GOOD and vice-versa on 8 NVMe drives connected behind Atlas and drive push pull is run in parallel.(DCSG00936303 (Port Of Defect DCSG00961699)
-Add infrastructure to provide connector index for applications to fetch connector name(DCSG00325884 (Port Of Defect DCSG00371116)
-Out of bound memory access when assigning dma group for controller devices.(DCSG00243152 (Port Of Defect DCSG00243641)
-Data Abort seen while starting the copyback from OOB(DCSG00431166 (Port Of Defect DCSG00521373)
-FW faults when generating an on-demand snapdump after single ECC error test(DCSG00253370 (Port Of Defect DCSG00311642)
-Assertion hit while Expander Fw download in loops with phyop enable/disable(DCSG00433696 (Port Of Defect DCSG00521375)
-0x6001 Fault running TMs with certain NVMe translated Host IOs(DCSG00362831 (Port Of Defect DCSG00385767)
-[SATA Only] SCSI Start Stop Unit command with power condition active fails.(DCSG00349970 (Port Of Defect DCSG00353138)
-Firmware fails to send Enclosure removal event to host when the enclosure is removed from the topology.(DCSG00232962 (Port Of Defect DCSG00244617)
-NVME EPDs, with heavy IOs and TM from host side and NVMe passthru commands in loop from OOB. After 5-8 hrs hit KA(DCSG00939439 (Port Of Defect DCSG00959006)
-MR 7.15 Alpha - Large IO Support is allowed to be changed, but can't be set(DCSG00304321 (Port Of Defect DCSG00313289)
-MR 7.17 PA1: Excessive prints in etty log(DCSG00408200 (Port Of Defect DCSG00926314)
-MR 6.14:While clearing the configuration sanitize running drives state has been changed from SANITIZE_IN_PROGRESS(4) to UNCONFIGURED_GOOD(0)(DCSG00146728 (Port Of Defect DCSG00215259)
-CLI application shows improper error import message after successful Foreign import(DCSG00915940 (Port Of Defect DCSG00920227)
-0x6001 Fault while running driver load/unload with simultaneous NVMe drive pulls(DCSG00378243 (Port Of Defect DCSG00385686)
-ExtManPage41 TX Values are not being applied / run by AERO SERDES(DCSG00311524 (Port Of Defect DCSG00311739)
-Customer solution getting lower performance than benchmark platform in Random Read&Write(DCSG00548054 (Port Of Defect DCSG00832401)
-Ventura/Mercator: pl: 4311 fault(DCSG00918020 (Port Of Defect DCSG00928996)
-Ventura: Faults 0x0101 and 0x5805 Invalid LMID Index Seen after hundreds of cold boots(DCSG00338118 (Port Of Defect DCSG00384000)
-ventura build issue with PL PCI DEVICE feature disabled(DCSG00286358 (Port Of Defect DCSG00286361)
-OOB - Diag test fails when duration=180secs(DCSG00381399 (Port Of Defect DCSG00384179)
-LED Blink/Unblink operation fails on certain Slots in UBM using MPI SEP Request(DCSG00282826 (Port Of Defect DCSG00290200)
-PL NVMe : PCI task management is not getting completed.(DCSG00231422 (Port Of Defect DCSG00245537)
-PL SATA Only : Controller hang observed for ATA Passthrough command with count value set to 0(DCSG00250952 (Port Of Defect DCSG00266833)
-PL fault 0xE40E observed accessing unconfigured MPI backend device registers through CLI cmd(DCSG00234837 (Port Of Defect DCSG00238649)
-HBA hangs on boot with failed UBM backplane in a multi-UBM backplane topology(DCSG00653774 (Port Of Defect DCSG00707464)
-Aero MR7.17 Alpha - Missing ME Events on PD during recovery(DCSG00707151 (Port Of Defect DCSG00907155)
-When performed export csr for all 8 slots in batch observing for few slot command is success and for other it is failure.(DCSG00421812 (Port Of Defect DCSG00425171)
-Able to import PD after FW treats VD/PD missing for RLM as Critical (OCR case)(DCSG00258652 (Port Of Defect DCSG00543349)
-EID is not assigning back with IT controller restart(DCSG00394045 (Port Of Defect DCSG00397565)
-When key exchange fails, encryption mode doesn't report failure(DCSG00267743 (Port Of Defect DCSG00344588)
-MR 7.17_SLT: PD erase shows success for the enclosure(DCSG00547453 (Port Of Defect DCSG00734514)
-Double AEN for JBOD is now secured event(DCSG00293327 (Port Of Defect DCSG00311644)
-Drives connected behind external card with VSES disabled, failed to detect in Linux OS(DCSG00350402 (Port Of Defect DCSG00363785)
-MR_7.17_PA1_DBU:ERROR- Exception Handler Called for Processor Core = 0 during OnDemandSnapDump IOCTL fire on Ventura IMR(DCSG00426994 (Port Of Defect DCSG00941071)
-Bad Phy events are generated for UBM slots with element status = NO_ACCESS_ALLOWED(DCSG00336611 (Port Of Defect DCSG00353452)
-[Aero/Ventura] Bootloader corruption with firmware download and DC cycle in loop.(DCSG00238233 (Port Of Defect DCSG00245454)
-DRIOE_SRetryExhaus for mid 1402 devId 1 isEpd 0 devH 1c pMpt 17933400. Failing IO tbIO=1 RC=5 reported on eacj devices after Driver unloaded.(DCSG00391062 (Port Of Defect DCSG00543274)
-On enclosure power cycle, previously configured drives come back as unconfigured good drives(DCSG00525893 (Port Of Defect DCSG00914313)
-Secure erase operation fails on a Ubad NVMe Opal drive(DCSG00343585 (Port Of Defect DCSG00349550)
-MR 7.17- DC with outstanding RMW commands on 16 drive R6(DCSG00427249 (Port Of Defect DCSG00501377)
-OOB Debug logs does not capture all required logs.(DCSG00427927 (Port Of Defect DCSG00521368)
-Controller hangs after attempting to import a foreign config with a pending personality change.(DCSG00432564 (Port Of Defect DCSG00543342)
-[Aero][PLDM] PLDM FW discovery results in 265D Fault(DCSG00307769 (Port Of Defect DCSG00330183)
-Able to flash from EKMS supported to non EKMS supported FW when EKMS is enabled(DCSG00393114 (Port Of Defect DCSG00399185)
-When Enhanced BGI kicks in on multiple VDs, the print does not reflect the correct VD/LD id.(DCSG00353756 (Port Of Defect DCSG00356168)
-PBP: OEM storage app not reflecting PD removal(DCSG00430563 (Port Of Defect DCSG00913673)
-Update the SPDM print index properly before adding the prints to ring buffer(DCSG00335886 (Port Of Defect DCSG00337717)
-[NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive(DCSG00136092 (Port Of Defect DCSG00237479)
-Incorrect PLDM firmware release date is displayed in BMC applications(DCSG00926179 (Port Of Defect DCSG00959007)
-MR 7.17 Alpha: After OCR where drive is pulled during OCR, controller comes back in safe mode even though VD should only be degraded(DCSG00557518 (Port Of Defect DCSG00920085)
-Remove LogSpecific member in the structure 'IOPI_LOG_DETAIL(DCSG00318366 (Port Of Defect DCSG00318943)
-Drive changes from UG to UB, when user start the initialization followed by secure erase on same drive(DCSG00837473 (Port Of Defect DCSG00957942)
-OEM UBM backplane Slot status LED Blinks only for 10 secs for NVMe VDs with Toggle Host LED management(DCSG00323361 (Port Of Defect DCSG00380726)
-Last LDBBM entry in the list is not cleared after VD Deletion(DCSG00255330 (Port Of Defect DCSG00257909)
-9500-16e fails to recover after warm boot(DCSG00422618 (Port Of Defect DCSG00422813)
-PL: Reply to IO's bad SGL to Atlas SES has wrong DevH and SMID's incorrectly tries to fit 3 SGEs inframe(DCSG00315476 (Port Of Defect DCSG00366033)
-RDE - Invalid PCI slot number being set for few RDE alerts(DCSG00335901 (Port Of Defect DCSG00367086)
-As part of the Device Add\Removal Event, the enclosure handle passed on by the PL FW to the upper layer is incorrect.(DCSG00298128 (Port Of Defect DCSG00299826)
-Initiate OOB FW download on the Ctrl while flashing the FW from in-band led to Exception mon_task(DCSG00431713 (Port Of Defect DCSG00543478)
-pl: backend PCIe: limit CRS retry count(DCSG00312206 (Port Of Defect DCSG00324774)
-[VSes] Slot status is reported as 'Unsupported' for drives connected to UBM backplane.(DCSG00337912 (Port Of Defect DCSG00353069)
-PL NVMe : IOs fail with SGL length shorter than the transfer legth(DCSG00501518 (Port Of Defect DCSG00735325)

EnhancementRequests:
-SPDM IT: Add memory allocation/free for SPDM_LIB(DCSG00229260
-pl: backend PCIe: runtime control for lane margining debug console prints(DCSG00373313
-RDE - Fill PartNumber and SKU based on the controller model(DCSG00433340
-Convert free space in NVRAM to STATIC Section (NVRAM API portion)(DCSG00398092
-[NVMe] SCSI Send Diagnostic command translation for NVMe.(DCSG00261270
-Enhancement to source of randomness for generating key pair(DCSG00208477
-Implement NVMe shutdown for MR7 programs (Followup PL changes. )(DCSG00274125
-SMART Polling Improvement -New Dynamic Section to save New Controller properties structure in NVSRAM(DCSG00248087
-pl: backend PCIe: CRS retry limit disable bit(DCSG00325823
-Update SAS 3.5 FW summary release notes(DCSG00384316
-Add a Snapdump fault code for printing errors(DCSG00231367
-SPDM: add support for MCTP_CTRL_CMD_GET_MSG_TYPE_SUPPORT in MR as in IT(DCSG00258208
-Add new events for - Block Multi-LUN / Multi-Actuator : SAS Device only Report as Unsupported Device(DCSG00921464
-VSES: Removed loginfo code when the command is failed with a check-condition(DCSG00235941
-Assert Audit : Ocm Copy - col_common change(DCSG00437203
-Add an Allow List for symbol_dump.txt in Snapdump(DCSG00340406
-Update the event logging when the "CoreDump" region is erased from ScrutinyCLI command(DCSG00367325
-MR: Update to latest SNTL specification Phase 2(DCSG00310363
-MegaAPI_PVT: Add API changes for Support WJ Pinning for both WB and WT Parity RAID VDs (PR: DCSG00166915)(DCSG00315910
-Assert Audit: Asserts are not required in the function which determines if NAND flash part is supported(DCSG00421730
-[IT SPDM] Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust(DCSG00218564
-[IT SPDM] Implement client APIs for SPDM Get Measurement command.(DCSG00256411
-Add version control file to build(DCSG00242260
-Add OEM key signing support for local FW builds(DCSG00548046
-MR FW Ruby SED Support(DCSG00054998
-Shenandoah : Code Cleanup activity(DCSG00385777
-Ventura/Aero: Request by MegaRAID to output debug data in vtboot.rom for future debug(DCSG00420316
-RDE - Remove event schema property "EventType" for all RDE alerts(DCSG00351956
-Use rubySupportOption to force dual featured FDE drives of Ruby and Opal to be detected as Opal drive only(DCSG00360412
-RDE - Make changes to logging of few RDE alerts(DCSG00335913
-Assert Audit: Removing asserts from the DEBUG module(DCSG00433168
-Snapdumps will get deleted for FW upgrade/downgrade operation.(DCSG00290210
-[NVMe] Provide interface to reset NVMe drive after shutdown.(DCSG00109904
-Enable end user tools to read custom SN(DCSG00938513
-Security Key page MPI definitions should more descriptive(DCSG00336313
-MR PVT API Atomic LKM-to-EKM transition(DCSG00426511
-Reset mechanism for OEM Pismo Beach Plus and Zuma Beach cards(DCSG00347300
-Convert free space in NVRAM to STATIC Section(DCSG00347347
-Fix NVRAM Dynamic Section Conflict issues(DCSG00347343
-MR FW: Add CLI command to control Parity Read Cache Bypass for SSD VDs(DCSG00342281
-SnapDump Enhancement: Implement _DumpBytesSkipZeros()(DCSG00302279
-Drives connected to OEM controller behind Atlas PCI switch HII bayID:Slot# enumeration(DCSG00051210
-Adding Incremental progress events for Patrol Read(DCSG00304274
-Snap-dump Enhancement - remove unnecessary duplicate prints(DCSG00312222
-[Ventura/Aero] Block the OOB FW download when firmware update is in progress.(DCSG00249958
-Enable Legacy OpROM support for ALL OEM iMR and MR Ventura Family RAID adapters.(DCSG00310369
-Enable ONFI to print bad block debug print at default debug level(DCSG00414717
-Added IOCParam to IOUnit Control command to allow periodic time-sync(DCSG00235948
-[SPDM IT] Export CSR & Import Cert Open & Close Session(DCSG00221406
-Support for sanitize command - passthrough(DCSG00237038
-Add SES status page flags to debug prints(DCSG00383509
-Release Automation: Add support for generating Ventura ROP(DCSG00246102
-Aero Secure Boot: Add Key Update Pending Check for 'COMPLETE' Image Download(DCSG00241566
-Add a build tool for spell checking(DCSG00546011
-Assert Audit: Removing an unnecessary null pointer assertion(DCSG00421720
-[Aero/Ventura]Fix Coverty issues in Phase_18 TIP(DCSG00507240
-Total vSES Enclosure Slot Count value reported is incorrect in host tools\MR FW with NVMe drive which fails initialization(DCSG00546745
-Examine passthrough code path and block inappropriate commands to LD(DCSG00358710
-[NVMe] Prevent non Read/Write SCSI IO Timeouts while running heavy greater than MDTS RW IOs(DCSG00234748
-Code changes to make sure we do not block downgrade to older packages(DCSG00356751
-NVMe Init Failure Reporting & Recovery of NVMe Drive with Partial Capacity NSID 1 Namespace(DCSG00310384
-Additional NameSpace behavior changes(DCSG00310383
-Vent/Aero: Integrate SPILIB 20.00.14.00(DCSG00317165
-RDE - Make changes to severity of few RDE alerts and drive resource properties(DCSG00306601
-SPDM: Add test case in Megamon SPDM Test Framework(DCSG00380977
-Assert Audit: Remove redundant max thread assertion check(DCSG00422225
-Implement NVMe shutdown for MR7 programs(DCSG00109903
-SBLIB: Add backward compatible build environment with new Avenger build(DCSG00320810
-Fix the target Id reuse issue(DCSG00342296
-Update JBOD (SYS PD) creation logic to not erase DDF area on the drive(DCSG00421662
-Add new field DEPOPULATION TIME as part of translation of VPD Page - Block Device Characteristics.(DCSG00167925
-OEM Smart Carrier Backplane code cleanup(DCSG00171467
-SPILIB2: Integrate 20.00.11.00 with the IT firmware tip(DCSG00297796
-Add Mrparamspage0 bit(plannedVDRemoval) to control OEM feature(DCSG00395756
-Assert Audit: Removing an unnecessary null pointer assertion(DCSG00421724
-Assert Audit: Removing FS Config, Offload Metadata, Flash I/O metadata ASSERT checks(DCSG00423579
-Enabled cache retention testing for factory testing(DCSG00342312
-pl: NVMe: update to latest SNTL specification Phase 2(DCSG00340625
-MR7 : Support WJ Pinning for both WB and WT Parity RAID VDs(DCSG00214468
-Add dumps to pl dbg(DCSG00008206
-Change the severity of IML error code 0x1911 from CAUTION to CRITICAL to match with RDE alert "DriveFailed"(DCSG00342319
-MegaRAID FW implementation of parity read cache bypass (PR DCSG00237022)(DCSG00248967
-Support for Boot time password from HII - after controller boot(DCSG00165392
-Shenandoah RDE - Add support for Redfish Message Event(DCSG00258873
-PTB Improvements for UEFI start(), stop()(DCSG00266478
-Flash Improvements(DCSG00409912
-Assert Audit: Removing asserts from the PHY module(DCSG00433062
-Add an Allow List for symbol_dump.txt in Snapdump -- fw_bld_tools(DCSG00405512
-Update copyright for oem specific files and clean up code(DCSG00387800
-Snapdump Improvement - SES Enclosure related(DCSG00408681
-Assert Audit : Bbu Retention Test(DCSG00435907
-Fixed coverity defects(DCSG00350003
-VSES - UBM DFC Array Device Element status read optimizations(DCSG00347743
-MegaAPI: Add API changes for temporary key escrow (PR: DCSG00428069)(DCSG00935525
-Short term solution for handling SES cable missing to Atlas(DCSG00293135
-[NVMe] Update SCSI to NVMe translations based on latest SNTL document.(DCSG00235935
-NVMe Sanitize Translation(DCSG00266054
-Expose PSEC_SHA_HMAC_RESULT using sbliApi.h(DCSG00342857
-Update the IT/PL Firmware Error codes guide(DCSG00349980
-MR: Update to latest SNTL specification Phase 1(DCSG00253373
-MegaAPI: add MR_EVT_PD_OUT_OF_ORDER_DETECTED (PR: DCSG00401621)(DCSG00834870
-Add PLDM compiling support for both Channel and OEM targets(DCSG00382476
-Enable 24 NVME drive support for internal and external controllers(DCSG00306646
-MR FW: Update WJ Pinning to use new WJ Pinning XSD value(DCSG00366410
-SnapDump Enhancement: Move OOB messages out of etty (snapdump) and have under debug flag(DCSG00299476
-Fixed compilation issue(DCSG00415061
-Host Trace Buffer Triggers to be persistent(DCSG00235945
-Add early notification event for possible incomplete writes on parity VD's in case of bad or missing Battery(DCSG00229751
-SnapDump Enhancement: Capture Nvme identify info in the snapdump.(DCSG00299471
-Print Battery Monitored Information once every week(DCSG00318550
-CIO deprecated IOtype display while recon Vd - to be removed(DCSG00301684
-Use NVDATA flag to switch on/off support for Pismo Beach Plus's single port / multipath topology(DCSG00323867
-MR: Write Journal Pinning debug cleanup(DCSG00326968
-Assert Audit : Ocm Copy(DCSG00435908
-Support for Mode 5 NVMe drive firmware download with Chain SGL SCSI Write buffer request.(DCSG00171452
-Address coverity tool reported issues against OEM specific platform MR FW.(DCSG00350023
-Increased firmware image size from 4MB to 5MB(DCSG00335263
-Code cleanup activity(DCSG00385894
-Improve SES slot access for the host(DCSG00703250
-Fix coverity tool reported defects(DCSG00351970
-Need MR firmware method to mark virtual drive(VD) for transport to new RAID controller so that new controller will respect DDF consistent flag(DCSG00347297
-Revert back to using original EKMS AENs(DCSG00326374 (Port Of EnhancementRequest DCSG00342275)
-LKM compliance to Cryptographic Algorithm Requirements v1.5(DCSG00830702 (Port Of EnhancementRequest DCSG00957810)
-Extending SnapDump Persistence(DCSG00247000 (Port Of EnhancementRequest DCSG00958045)
-NVMe Sanitize Crypto erase: Disable the "No Deallocate" option(DCSG00324837 (Port Of EnhancementRequest DCSG00342273)
-VSES: Update diag page 02h status reporting for Array device elements to use UBM DFC SnC Desc Element status code(DCSG00308393 (Port Of EnhancementRequest DCSG00379789)
-Disk labels need to be tied to fixed physical ports in order(DCSG00240927 (Port Of EnhancementRequest DCSG00957939)
-Implement delayed VD secured event Modification(DCSG00253141 (Port Of EnhancementRequest DCSG00259199)
-To support Atlas switch additional FW change were required for HII to enumerate bayID#:Slot#(DCSG00408798 (Port Of EnhancementRequest DCSG00411520)
-Integrate PLDM platform changes as per new PLDM library for separation of APIs/LIB and source code(DCSG00415391 (Port Of EnhancementRequest DCSG00528189)
-Disable removal of key caching(DCSG00378005 (Port Of EnhancementRequest DCSG00404164)
-Examine passthrough code path and block inappropriate commands to LD(DCSG00358710 (Port Of EnhancementRequest DCSG00903416)
-Q-depth optimization to improve read performance for R10 and other array configurations with spanned arms(DCSG00914358 (Port Of EnhancementRequest DCSG00959591)
-Remove Retries When INQUIRY for Extended VPD Page 86h Returns 5/24/00(DCSG00922081 (Port Of EnhancementRequest DCSG00959012)
-FW support for customer GlobeMaster Topology(DCSG00258112 (Port Of EnhancementRequest DCSG00311654)
-Add an additional hard coded battery pack DPN(DCSG00408305 (Port Of EnhancementRequest DCSG00414782)
-Boot sequence event udpate(DCSG00335552 (Port Of EnhancementRequest DCSG00353556)
-SMART Polling Improvement - MR FW Changes to access New Controller Properties Extended structure(DCSG00248098 (Port Of EnhancementRequest DCSG00258073)
-Disable rescanning of enclosures status page for UBM backplanes(DCSG00386600 (Port Of EnhancementRequest DCSG00579842)
-Log 0 SPDM events for certificate slot & key management(DCSG00322202 (Port Of EnhancementRequest DCSG00366811)
-Improve SES slot access for the host(DCSG00703250 (Port Of EnhancementRequest DCSG00777363)
-NVMe Passthru command support(DCSG00432879 (Port Of EnhancementRequest DCSG00957826)


Version 51.15.0-4005 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:7.15.00.0
	UEFI Driver:0x070F0301
	HII: 07.15.04.02
	MR FW: 5.150.00-3499
    package 51.15.0-4005

Defects:
-Atlas BST: Change 4.x RDK BST to use 7z decompression for BST.(DCSG00832411)
-MR_FW Aero 7.15: Switching OOB mode from I2C to PCIe is not working when we set thru OOB SLT.(DCSG00914004)
-OOB parallel PD FW download should not be allowed in I2C mode.(DCSG00935499)
-"Force" option is asked to downgrade when EKMS is enabled with secure config.(DCSG00935748)
-Storage controller goes through repeated resets and is not discovered by host.(DCSG00943829)
-Aero MR7.17 Alpha - Missing ME Events on PD during recovery.(DCSG00707151)
-Fix for allowing offline VD to be set as bootdrive.(DCSG00925005)
-FW halts when "ubm show " is triggred.(DCSG00312896)
-MR_7.17_PA1_DBU:ERROR- Exception Handler Called for Processor Core = 0 during OnDemandSnapDump IOCTL fire on Ventura IMR.(DCSG00426994)
-BST: ScrutinyCli invoked with invalid options.(DCSG00428615)
-[SATA Only] SCSI Start Stop Unit command with power condition active fails..(DCSG00349970)
-Intermittent hang condition on repeated reboots.(DCSG00318961)
-SBR Build date and time corrected.(DCSG00068041)
-Clean up SBR Build Tools.(DCSG00108561)
-Fix and Rename Common NVMe Header File.(DCSG00025545)
-Handling a newly added Cache loss Boot Message for IML.(DCSG00041692)
-Enable SSD Wear Gauge for NVME drives.(DCSG00042403)
-Fix for Data Abort Exception caused due to access of invalid device id in event structure.(DCSG00043231)
-For Vses device box info is populated..(DCSG00045198)
-Energy pack moves to failed state post controller reset.(DCSG00046787)
-Made platform changes for PLDM fw update operation.(DCSG00049608)
-Fix for misalignment of an internal structure.(DCSG00050922)
-VD creation with default WB policy to be blocked in P216i Controllers.(DCSG00054336)
-[Aero/Ventura] MCTP discovery fails after unload and load of MCTP driver in BMC(Board Management controller).(DCSG00058897)
-Disabling MR_CTRL_INFO.ldOperations.writePolicy bit in JBOD mode for specific OEM.(DCSG00069218)
-Fix for incorrect bay count value..(DCSG00071758)
-GetSchemaDictionary command executed from RedACT is failing for annotation schema.(DCSG00078890)
-Shenandoah RDE: Fix PCIe interface details.(DCSG00080093)
-FW hits assert when NVMe drive returns non-success reply for admin commands.(DCSG00080405)
-Drive count not correct in CLI for UBM3 x4 backplane with SAS drives connected.(DCSG00081735)
-Return MFI_STAT_NO_HW_PRESENT for some bbu DCMDs for 216 controllers.(DCSG00081956)
-FW changes to support removal of "Bays on port" field in APPs.(DCSG00082494)
-UBM3_x4-Solid Green LED turned on on JBOD drives after few drive pus pulls.(DCSG00085866)
-RDE: Fix operation for volume and link error threshold for port.(DCSG00097465)
-Ventura/Mercator: pl: 4311 fault following SAS IO Unit Page 1 write.(DCSG00099275)
-Disable R0 Autoconfig option from FW.(DCSG00109751)
-Firmware hits exception on power cycling the server with NVMe drives connected.(DCSG00109752)
-OEM board: SAS drives the link speed is shown as unknown.(DCSG00110319)
-RDE : Query for drive information which was part of volume where full initialization was running results in unexpected error in REST client.(DCSG00112022)
-RDE -"Volumes@odata.count" is coming up as 0 for a Dedicated Spare drive which is part of a Volume.(DCSG00112594)
-Fix iMR save code in create small dumps.(DCSG00113527)
-RDE - Virtual drive 'PercentageComplete' shows 100 in REST client for volume resource when erase operation is running.(DCSG00113953)
-RDE - Storage Controller cache health status should display "Warning" if WB cache enabled Volumes present but energy pack is failed, missing or charging.(DCSG00115184)
-MR_7.14 PA2 DBU: FW received the KA, while running IO with IOCTL command in a loop.(DCSG00117767)
-SPDMLIB: Add change to SConstruct to copy library output file (*.a) to release folder.(DCSG00117832)
-MBEDTLS LIB: Add change to SConstruct to copy library output file (*.a) to release folder.(DCSG00117834)
-RDE - REST client displays error when tried to get drive resource details on a AROC controller.(DCSG00125938)
-Firmware faults when reconstruction is going on with cable pulls.(DCSG00134460)
-RDE - Drive schema shows operations as "Erasing" and percentage "0" after initiating LD erase/initialization operation.(DCSG00134506)
-IT SPDM commands not working via host interface.(DCSG00134673)
-Fix print nesting for ASCII eTTY.(DCSG00134926)
-RDE - "StripSizeBytes" shows double the actual strip size value for the volume resource in REST client.(DCSG00136280)
-Remove stale parameters from NVDATA.(DCSG00136341)
-Aero MR 7.14 PA2: Win/Lin Gen4 NVME: -15% drop seen in OLTP profile for IO Size-256K from QD-64 to QD256 in R0-1WRK.(DCSG00137117)
-The test tool does not reflect correct bad block count when additional bad blocks are added.(DCSG00139682)
-RDE - REST Client displays truncated drive size for NVMe drives.(DCSG00148309)
-Fix unintended update of BBM Long size..(DCSG00148922)
-MR_7.14 Alpha DBU: VMWARE reported IOMMU fault detected for vmhba3(Ventura IMR)..(DCSG00149010)
-7.14 SPDM client code fix: Enable Route By ID for all the packet..(DCSG00150120)
-SCSI Passthrough format command on unconfigured good drive causes kill adpater.(DCSG00150798)
-VenturaMR 7.14Alpha: -24% drop and 55% gains seen in SDR0, R0 for SW, RW for IO Size-4K-1M, QDs-4,16,64,256 - 64D-12G SAS HDD Expander connect.(DCSG00150877)
-Resetting the event counters in Ext. SAS/PCIe IO Unit Page 250 fail.(DCSG00150901)
-RDE - Firmware crash observed after querying LD information from REST client on AROC controller.(DCSG00151330)
-Release Automation: Exceptions during execution of release script.(DCSG00151389)
-Applications displays incorrect PD count with SATA drive in enclosure on multi-path configuration.(DCSG00151556)
-MR_7.14 Alpha DBU: Ventura iMR FW received a command "getCdbPtrAndTargetId: Invalid cmd fa", it result to KA on VMWARE OS..(DCSG00151683)
-Aero MR7.15 PA - Aero+Atlas Eval Invalid enclosure and slot info from nvmeiniterrorlist.(DCSG00151747)
-MR7.15 PA1: excessive "In OOBExecCmdIssue and dmcd is 0x#######" prints seen on termlog.(DCSG00152105)
-Aero Host Application Loading Changes to Support CTRL-R.(DCSG00152618)
-Fix assert in etty debug code.(DCSG00152802)
-RDE - Make Redfish Tool compatible with python 2.(DCSG00166025)
-OOB : Controller is not discovering thru OOB Storelibtest in pcie mode on loading /unloading SLT multiple times..(DCSG00166684)
-Updating FW (on 9400 series HBA) from Ph-7 to Ph-14 causes "invalid flash" message on FW bootup.(DCSG00167100)
-Running format on a EPD once one has started is causing a KA..(DCSG00167682)
-The "Last Erase Block' reported in the debug data is incorrect..(DCSG00170637)
-SPILIB: Winbond 256MBit maximum page write time increased from rev "A" to rev "B" of their specification.(DCSG00170747)
-MR7.15 PA1: Enclosure disappears after back to back ESM FW update with IOs.(DCSG00171108)
-Fix stack printing in "ef" command.(DCSG00171225)
-Fix error handling in traceTool.py.(DCSG00181406)
-PL: Aero -- Atlas US Cable Pull/Push Results in Missing Enclosure Slot Info.(DCSG00181448)
-MR 7.14 Beta: OCR did not complete appropriately and assert didn't print properly.(DCSG00212038)
-MR7.14: Controller Bios never sent the printing-has-completed DCMD.(DCSG00212592)
-Fix mistaken warning of drive degradation detection messages.(DCSG00212751)
-Observed Data Corruption during IO stress test..(DCSG00212797)
-iMR boot stuck in creating slot mapping.(DCSG00214223)
-Correct Sblib Int make sure ER 110403 and ER 166877 are present.(DCSG00214265)
-MR 7.14 Beta: Assertion failure in fw\raid\mpthostcmd.c at line 3213: crd->mptReqDesc.Default.SMID.(DCSG00215378)
-Correct Sblib Int make sure ER 110403 and ER 166877 are present (2).(DCSG00215388)
-MR7.14 Beta: Firmware hit exception stuck while IOs and rebooting, causing no controller found.(DCSG00215476)
-MR7.15 PA1: VDs missing after upgrade/downgrade between MR7.14 FW and MR7.15 FW.(DCSG00216224)
-SSD Estimated Life Remaining in Days shown appropriately for nvme drive.(DCSG00216327)
-NVRAM changes for supporting dynamic recon ghost tgtId.(DCSG00216908)
-MBEDTLS LIB: Fix dynamic memory release bug in Mbed Tls Library.(DCSG00216944)
-216-x controllers do not have ONFI support, optimized the code.(DCSG00217262)
-Expander FW fail to flash FW sometimes in offline mode.(DCSG00217264)
-Add PCE register dumps to snapdump.(DCSG00218199)
-Make PLDM platform code compiling without OOB_COMMON.(DCSG00219528)
-MR7.15 PA: FW gets hung while generating snapdump through MegaMon call SnapDumpDbgGlobalOnly.(DCSG00220882)
-MR 7.15: Invalid Arguments error seen while setting config file w.r.t JBODs from Storcli.(DCSG00221279)
-MR7.15 PA1: Downgrading to 7.14 FW when device order by firmware is enabled causes controller to be not accessible in OS.(DCSG00221705)
-[Aero] SATA drive gets dropped when corresponding phy is disabled and enabled.(DCSG00222544)
-RDE - REST client displays drive state as "Disabled" when initialization is running on the Volume configured on that drive.(DCSG00223283)
-9580-16i controller with PCIe switch doesnt see fault LED on offline PD.(DCSG00224982)
-Fix the decision in zcdump for which context to run in.(DCSG00225050)
-SPDM LIB: Set ECDSA signature with correct size in Signature field of SPDM Challenge response buffer before sending to BMC server.(DCSG00225192)
-Implicitly error when converting an expression to a narrower type.(DCSG00225977)
-Fix static analysis defect.(DCSG00226155)
-SPDM 7.15: return actual size of certificate chain content to SPDM LIB.(DCSG00226169)
-Aero 7.15 MR: Add memory allocation/free for SPDM_LIB.(DCSG00226196)
-Fix offset comments in DM IO Context.(DCSG00226222)
-Evaluate the MFI stats returned with the updated recon behavior.(DCSG00227245)
-Import certificate command with out seal option is failing for slots 0 & 1..(DCSG00228127)
-MR7.15 Dev: reduce dmSpinCheckAndRetryCmd etprints..(DCSG00228143)
-MR 7.15 PA2: Extra prints not seen before that appear to be debug: setup_cache_headers.(DCSG00228849)
-Remove MR's EXT_MFG_49 define. This change should be pick up from DCSG00228036 Pre-Alpha Release: CtrlFw_Ph_16.0 - 15.250.05.00 MR PL.(DCSG00229397)
-MR7.15 PA2: JBOD is missing after downgrading to 7.14 FW and upgrading again.(DCSG00230227)
-MR7.15 PA2: driver health message displayed 1 more time after device order by firmware is disabled on Windows system.(DCSG00231084)
-7.15 Aero: Call SPDMLibInit only if SPDM is enabled..(DCSG00231374)
-storcli 'start diag' command failed if ran after storcli 'show all' command..(DCSG00231398)
-Adapter got killed when trying to update Atlas FW using storcli with IO.(DCSG00231406)
-MR 7.15_IO tool detecting data integrity issue on 8i8e controller with NVME and SAS connected to different enclosure/Expander.(DCSG00231642)
-Coverity defect fix.(DCSG00231928)
-Use slot group number to get certificate algorithm record of security manufacturing page.(DCSG00232583)
-Firmware fails to send Enclosure removal event to host when the enclosure is removed from the topology.(DCSG00232962)
-Aero MR715PA - Aero + Atlas FW download blocks IO causing driver KA and OCR.(DCSG00233642)
-Coverity Defects in SATA and VPP code.(DCSG00234415)
-duplicate entries of arrays when creating hot spare drive caused storCLI to display incorrect information.(DCSG00234562)
-NVDATA XSD in MR is out of sync from the latest spec.(DCSG00234826)
-Merge conflict issues.(DCSG00234911)
-MBEDTLS LIB: fix compilation error during IT FW build.(DCSG00234920)
-(MS SES) Non data transfer SCSI IO failed with Invalid SGL error(DCSG00234926)
-Coverity defect fix in FPE code..(DCSG00235474)
-[9440-8i+MR7.12/7.13/7.14Beta2+ARM] controller FW printed Assertion failure in fw\cpu\arm\exceptions.c at line 1006: 0 during fio issue verify(2F) commands.(DCSG00236990)
-RDE - "EncryptionAbility" field for SED drives displays blank.(DCSG00237493)
-Controller fault observed on changing some phys to manual port config with port set to 0..(DCSG00237498)
-SPDM_LIB: Add alignment parameter into SPDMLib_Calloc interface.(DCSG00237674)
-7.15 Aero MR: Add alignment parameter into SPDMLib_Calloc interface.(DCSG00237675)
-SPDM_FW : Delete/Import foreign configs should not be allowed until SPDM Authentication happens between BMC and controller..(DCSG00237704)
-MR_7.15: Driver load/unload result to Assertion failure in fw\hw\debug\ptb.c at line 618: 0 on Aero card.(DCSG00238473)
-MR_7.15: User disabled PTB not reflected, hence PTB.txt is part of OnDemand SnapDump.(DCSG00238510)
-SPDM_LIB: Set tagOwner as per SPDM request.(DCSG00239464)
-SPDM 7:15 Set tagOwner as per SPDM request.(DCSG00240237)
-MR_7.15: PTB switch to Enabled and Save. No PoP up message reboot required/PTB.txt not part of Snapdump..(DCSG00241021)
-Fix static code analysis defect.(DCSG00241024)
-Fix static code analysis defect 128532.(DCSG00241025)
-Fix static code analysis defect 127973.(DCSG00241062)
-Fix static code analysis defect 127860.(DCSG00241065)
-Fix static code analysis defect 127845.(DCSG00241066)
-Aero MR715PA - Aero + Atlas switch write buffer command fails occasionally.(DCSG00241202)
-MR7.15 PA2: drive and enclosure connector are reported differently in Ctrl-R for OEM controller.(DCSG00241278)
-NVMe Init error drives are not discovered after pull/push within DMD timeout.(DCSG00242197)
-Out of bound memory access when assigning dma group for controller devices..(DCSG00243152)
-RDE - REST client displays ReadCachePolicy as OFF for Read Ahead enabled volumes.(DCSG00243670)
-Secure SED and SES Management ctrl properties are toggling after changing autoconfig from None to JBOD and vice versa..(DCSG00243819)
-WG: LSA does not allow to change to any other behavior once encountering error during behavior change.(DCSG00243910)
-FW : OCR fails to start from OOB Storelib test, and controller fails to discover in OOB SLT after this failure.(DCSG00245029)
-Ventura: SAS3616W or SAS3616W based boards have links less than epected width.(DCSG00249594)
-Aero A0: External cards do not support more than one PCIe drives..(DCSG00249770)
-Manage PCIe Interface page should be greyed out for UBM if the user is not allowed to make any Link Width changes.(DCSG00251554)
-Fix static code analysis defect 45959 45944.(DCSG00253256)
-Aero Seeing "SpdmReadCertForSlot[277]:[Error] Certificate Read Failed" on IT card after Controller Resets.(DCSG00253315)
-Fix static code analysis defect 127882.(DCSG00253339)
-UNMAP support is blocked and disabled.(DCSG00253426)
-Fix incremental Coverity builds.(DCSG00254162)
-Atlas 4.2: Prints "C0:EnclSesPdAccessAllowed: SES not ready (opState:10000) pd:0" observed in Aero FW logs, after upgrading/downgrading the Atlas RDK FW which is connected behind Aero controller.(DCSG00254663)
-MR7.15 Alpha (DBU) WG: LSA allows user to assign drive in prepare for removal state as replacement for missing drive for a DG.(DCSG00255186)
-crypto erase not completing on SATA drives.(DCSG00256740)
-MR 7.15 Alpha: securesed property can be set but not shown under show personality cmd for NONE mode.(DCSG00257803)
-Aero MR7.15 Alpha - PR stalls, never completes on NVMe PDs.(DCSG00267705)
-Timestamp is not getting established in Atlas FW, when Atlas is connected behind Aero Controller.(DCSG00268587)
-In JBOD personality SES management bit is not set in auto configure supported bits for NONE Mode.(DCSG00278401)
-OEM Server: Foreign Secure Drive - Clear drive option is Enabled..(DCSG00282684)
-MR7.15: FW hit Assertion failure in fw\raid\fwDownload.c at line 1159: fwDownload.pdRestrictCount!= 0 while flashing encl & PD firmware correspondingly.(DCSG00283749)
-ventura build issue with PL PCI DEVICE feature disabled.(DCSG00286358)
-System POST not proceeding and keeps on loading EFI SAS driver.(DCSG00287132)
-MR7.15: Flashing Atlas RDK firmware via storcli caused MR firmware crash.(DCSG00297302)
-Pre-boot crash snap dump is not fully captured.(DCSG00297597)
-MR 7.15 Alpha: PR estimated time left is wrong in multiple places.(DCSG00297903)
-SPDM 7.15: Dev DF - return appropriate error to SPDM Lib when read certificate from security page 0 fails.(DCSG00298150)
-JBOD deletion event id 139 has slot id 255.(DCSG00299050)
-MR7.15 Alpha: Kill Adapter occurs during flashing enclosure firmware and heavy IOs.(DCSG00299407)
-SBLIB: Significantly longer boot times that previously encountered in MR CBB.(DCSG00299427)
-CTRLH- Incomplete Display of messages.(DCSG00301793)
-MR 7.15 Alpha - Large IO Support is allowed to be changed, but can't be set.(DCSG00304321)
-MR7.15 Alpha: JBOD drive still show and list as first in order device before VD even after system reboot (Jbob personality mode).(DCSG00304336)
-MR 7.15: SPDM: Select correct Hash Algo for CSR (Certificate Signing Request) & close CSR session for error case.(DCSG00304511)
-API clarification for large io support.(DCSG00307042)
-7.15 Static Analysis defect.(DCSG00307840)
-SBLIB: Getting Inconsistent secure ID on IT cards.(DCSG00309847)
-MR7.15: SPDM: Dev DF: Call revised SBLIB API to retrieve Secure ID.(DCSG00310427)
-MBEDTLS Lib: Alignment issues while certificate verification on IT cards.(DCSG00312818)
-PL: Reply to IO's bad SGL to Atlas SES has wrong DevH and SMID's incorrectly tries to fit 3 SGEs inframe.(DCSG00315476)
-BSOD observed with mode 7 Parallel PD firmware update in PCIe OOB.(DCSG00315988)
-[MBEDTLS] Device Key Pair Generation resulting in different Keys on IT card.(DCSG00318909)
-Atlas Behind Aero BST is not working as the correct XML file is not copied..(DCSG00322761)
-SPDM: Dev DF to check in a new environment variable to control disable/enable hard-coded key pair.(DCSG00324022)
-CLI allows auto configure R0 immediate command in ePD pass-through mode.(DCSG00119569)
-Index out of range is observed for print in ring buffer logs.(DCSG00134669)
-Direct attached PFA drive - LED is neither ON nor Blinking.(DCSG00111492)
-autoconfig field is not set to None when firmware is upgraded to current programme package.(DCSG00113492)
-COL Failure on AC cycle.(DCSG00132764)
-Atlas Behind Aero: PL Fault 0xEC1A When Performing Backend PCI Resets From Diagnostic Code.(DCSG00042688)
-NVMe devices VPD page 83 NAA descriptor may conflict with EUI64 ID reported.(DCSG00148775)
-The personality behavior=None is allowed to be set..(DCSG00079271)
-Import certificate command is failing via In-band.(DCSG00212544)
-Upto 90% performance drop with expander attached configuration.(DCSG00153860)
-EKM many key request events generated when creating secured VDs with multiple disks.(DCSG00141624)
-CurrentControllerMode Value is Showing "null" instead Of "RAID".(DCSG00149932)
-Disable break mirror support.(DCSG00147889)
-Unsupported drive LED Solid Green on Rear Backplane - LED flashing green expected.(DCSG00130055)
-Foreign configuration import fails after rekey operation.(DCSG00104797)
-Secured EPD IO Error = media is write protected after continuous PushPull within 2 seconds.(DCSG00081483)
-NVMe Identify Controller sent over OOB fails with MFI_STAT_INVALID_CMD.(DCSG00165400)
-Auto Cfg Parameters Changed is not generated when host led management is changed..(DCSG00118646)
-Cli utility allows auto config option when it is not supported.(DCSG00119468)
-AUTOCFG parameters- EPDParams is set incorrectly for NONE/OFF mode.(DCSG00127771)
-MR controller resets.(DCSG00119480)
-FW not checking bound on tty read DCMD, leading to send tty log twice.(DCSG00134946)
-SPDM_FW : SPDM commands are failing in OOB SL/SLT on Trinity M6 servers.(DCSG00126744)
-[Aero/Ventura]Allow the backplane detection state machine to retry the FRU detection..(DCSG00219908)
-[Aero/Ventura] Unused phys are managed by VSes in SGPIO BP mode.(DCSG00151021)
-Auto Configure EPD-PT set fails when sent with MR_AUTO_CFG_PARAMETER received from firmware for Auto configure Off mode.(DCSG00215315)
-SATA only : Controller hang is observed due to recursive function call..(DCSG00139294)
-PL SATA only : SATA init timeout observed due to drive taking longer to respond to sanitize status ext.(DCSG00225935)
-IOC Exceptions not getting cleared after flashing the BIOS image with correct ROP version.(DCSG00226395)
-Expander_FW : Expander FW upgrade or downgrade through CIMC is not getting reflected on host applications.(DCSG00171248)
-FW faults during driver unload and load process.(DCSG00107743)
-tty battery FRU sometime corrupt when reading from cli.(DCSG00222664)
-AXI access error from TxDMA engine when certain errors occur during Task Management processingAXI access error from TxDMA engine when certain errors occur during Task Management processing.(DCSG00078508)
-Auto Configure R0 option is showing in eHBA mode.(DCSG00235390)
-CTRL_MFC_DEFAULTS_SET DCMD returning error when customer controller is in eHBA mode.(DCSG00227153)
-[9460-8i+MR7.12 Patch+X86] Use script to upgrade customer-made SAS SSD firmware underneath 9460-8i (7.9, 7.11, and 7.12) will fail.(DCSG00124592)
-Target ID of EPD drives is not equal to Slot ID when drives are connected.(DCSG00167860)
-Some of the JBODs are not included under "PR excluded VD" , while performing storcli /cx show pr when all the drives are converted to JBOD..(DCSG00126731)
-StorCLI shows "PR excluded VDs" where actually PR is running on online PDs of VD..(DCSG00126725)
-In JBOD profile, set VD Write Cache to AWB shows success even though WB Supported is set to NO.(DCSG00113956)
-Auto Secure SED failure status is different in 2 different generation controllers..(DCSG00227232)
-Host utility can still manage LEDs when downgrading from FW with jbodhostledmgmt enabled to FW with jbodhostledmgmt disabled.(DCSG00230907)
-SPDM IT:SPDM BMC bring up on P2 server.(DCSG00238540)
-NVmeAdmin: Assertion failure in fw\raid\nvmePRP.c seen when NVMe PT response size is >=12k.(DCSG00223413)
-NvmeAdmin: 'Exception handler called' observed while converting drive to Non RAID preceded by Export Log from OM.(DCSG00224879)
-Drives returns incorrect session name in SEKM environment.(DCSG00229451)
-supportEPDWithAutoConfigOff supported bit is set as 1.(DCSG00239272)
-AXI access errors causing FW asserts or faults due to invalid SATA passthrough commands.(DCSG00215338)
-[NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive.(DCSG00136092)
-Current version of Back plane firmware does not display correct after update, Pathfinder.(DCSG00239284)
-[Aero/Ventura] Bootloader corruption with firmware download and DC cycle in loop..(DCSG00238233)
-PL NVMe : PCI task management is not getting completed.(DCSG00231422)
-[SPDM IT] Return actual size of certificate chain content to SPDM LIB.(DCSG00233805)
-Command to get ld Allowed Ops Ext can be called with wrong buffer length..(DCSG00223430)
-Preboot uitlity HII shows enable host led management button when feature is not available.(DCSG00229197)
-Expose enclosure controller property is being reset at every boot.(DCSG00244065)
-Controller crash and resets on attempt to boot to windows OS.(DCSG00099330)
-Dev-Defect - PRP-List overwritten in Double-Buffer-Copy-To-Host for response size > 8K.(DCSG00258471)
-Aero: PL with newer Atlas FW (4.2) has extra slot number in the Atlas enclosure.(DCSG00284238)
-Event is generated even though LDBBM table is not updated.(DCSG00259244)
-Last LDBBM entry in the list is not cleared after VD Deletion.(DCSG00255330)
-Assertion failure in fw\ddf\ddfPd.c seen during foreign import.(DCSG00272547)
-StorCLI shows success in Converting Foreign drive as JBOD.(DCSG00261213)
-[9440-8i + MR7.14 ARM/X86] Auto config RAID0 in HII didnot work as expected.(DCSG00297592)
-NVMe Init Error: Device with no namespaces shows 'Namespace count Invalid' as Unrecoverable Error.(DCSG00290593)
-As part of the Device Add\Removal Event, the enclosure handle passed on by the PL FW to the upper layer is incorrect.(DCSG00298128)
-MR FW not responding to resume within 3 seconds.(DCSG00243834)
-9440-8i System black screen and hang during S4 + CC stress.(DCSG00297794)
-After loading aero driver, the VD of the controller cannot be listed.(DCSG00297806)
-JBOD drive is converted to Configured Drive after OCR / Reboot.(DCSG00293760)
-ExtManPage41 TX Values are not being applied / run by AERO SERDES.(DCSG00311524)
-MR3508+MR7.14 +X86 ] Controller is seen with Fatal error by unknown reason unexpectedly (XH628 V5's 3508 mem.c issue).(DCSG00312708)
-9440-8i + MR7.14 + ARM] Controller hit Fatal error when doing drives hard reset test by storelibtest.(DCSG00312453)
-Aero MR7.16PA - snapdump hang during capture in Legacy BIOS.(DCSG00318700)
-[9440-8i+X86+MR7.13] SSD JBOD Drive state will change from (U-Up) to (D-Down/PowerSave) when they rmmod and insmod megaraid.(DCSG00265980)
-SATA HDD drive failing media error tests.(DCSG00232413)
-SSD cache policy change for 7.15 OEM boards.(DCSG00349494)
-FW crashes when FW upgraded.(DCSG00428848)

Enhancements:
-Update secureSign with signImageX to v2.18 DCSG00904128.(DCSG00904181)
-BST: Bring up new Aero activity BST server at BLR.(DCSG00323525)
-Total vSES Enclosure Slot Count value reported is incorrect in host tools\MR FW with NVMe drive which fails initialization.(DCSG00546745)
-Address the issue found during code review - flush write verify issues on MR7.(DCSG00011893)
-[Aero][Ventura] Sign windows build applications and avoid antivirus from deleting them..(DCSG00025757)
-SSD Wear gauge per Smart Storage Design Specification 1.64.(DCSG00028105)
-Displaying "Volume" instead of "Logical Drive" or "LD" in events and boot messages..(DCSG00029102)
-Implementation of changes as per new Energy Pack State transitions.(DCSG00034018)
-Make PLDM (Type 2) specific changes as per Smart Storage System Design Specification RevisionV 1.64.(DCSG00039603)
-Support for the Smart Array MR216i-p/a Gen 10+ Controller.(DCSG00041392)
-Implemented UBM box bay number support.(DCSG00042528)
-Export of UBM backplane type to the platform.(DCSG00046485)
-Implemented newUBMBackplane type support..(DCSG00049601)
-Populate connector name from sas device page 0..(DCSG00051271)
-Add Avenger support for libmbed tls..(DCSG00051695)
-Support for NVMe Firmware Download when the image size exceeds the SNTL Transfer limitation..(DCSG00053656)
-Additional FDE type for Ruby SED support.(DCSG00055878)
-Populate connector name from PCIe device page 0..(DCSG00057131)
-PLDM FW UPDT component classification updated.(DCSG00060855)
-Allow full binTrc ETTY collection for on-demand snapdumps.(DCSG00061636)
-Reverting branding changes.(DCSG00061954)
-Populate UBM backplane fields as part of EFI_HP_ADAPTER_INFO_SMART_CARRIER_BACKPLANE_DATA.(DCSG00062513)
-ISE completion status to support UEFI Sanitize protocol.(DCSG00062524)
-Support for config reset protocol.(DCSG00062958)
-Add milliseconds to etty print timestamps.(DCSG00066928)
-Snapdump performance improvements.(DCSG00066931)
-Update NVDATA to display appropriate controller names and to remove invalid connectors.(DCSG00068959)
-Shenandoah - Implement PLDM RDE Platform Firmware.(DCSG00068974)
-After purge operation, Blocking OOB traffic..(DCSG00071207)
-Remove protection of NVDATA pages for channel.(DCSG00079568)
-Package Stamping Verification.(DCSG00096506)
-Support UBM diag tools in Scrutiny CLI for MR.(DCSG00097311)
-PL: Coordinate reset on Atlas FW update to limit IO disruption to NVMe drives behind Atlas.(DCSG00097342)
-RDE - Display complete drive revision and model number strings in REST client.(DCSG00105101)
-Add support for U.2 UBM backplane.(DCSG00118415)
-PL UBM support UBM for PCIe SW upstream port config.(DCSG00120726)
-SPDM: Add messages to etty buffer as part of snapdump for SPDM.(DCSG00123020)
-On 9440-8i controllers, do not update timeout value for a DCDB issued by host on JBOD.(DCSG00128903)
-Enable NS management and Format commands in the PT path.(DCSG00129551)
-Snapdump doesn't log recon ld info.(DCSG00132717)
-Add autoconfig debug prints to snapdump.(DCSG00134888)
-Add preboot environment variables to snapdump logs..(DCSG00139621)
-Log SPDM events entries in log page 0.(DCSG00139949)
-Disable hardware debug ports.(DCSG00143569)
-Aero/Ventura: Add CLI to test QE bit modification.(DCSG00148653)
-7.15 SPDM: HW debug port disable and megamon utility limited access.(DCSG00148680)
-SPDM: 7.15: Enhancement to source of randomness for generating key pair.(DCSG00148777)
-MBEDTLS LIB: Enhancement to source of randomness for generating key pair.(DCSG00148786)
-Fix Mbedtls build scripts to accommodate Aero and Avenger.(DCSG00150272)
-API changes to expose MR_AUTO_CFG_PARAMETER for NONE mode.(DCSG00151058)
-Support snapdump for 216-x controllers.(DCSG00151384)
-Enhance OEMs Dev BST scripts for driver upgrade and downgrade.(DCSG00152322)
-Update WWID in the PCIe interface structure for PCIe switches.(DCSG00152603)
-Remove cdi get for Avenger.(DCSG00152679)
-Aero SPDM Sblib change: provide sblib interface to disable specified HW debug port..(DCSG00166877)
-RDE - Implement support for dynamic PDR repository change in Managed Device Firmware.(DCSG00167169)
-Add new security events.(DCSG00167313)
-ComboSerdes: add functionality for bypass ready waiting.(DCSG00167482)
-SPDM:7.15: Export CSR & Import Cert Open & Close Session.(DCSG00167484)
-Allow General Processing Failure from Atlas on unsupported commands to not result in 0xEA20 fault.(DCSG00170698)
-SPILIB 2.0: Add support for Block Protect bits configuration.(DCSG00170752)
-Updated personality change testing scripts to BST suite.(DCSG00171040)
-Implement a secure version of memset for SPDM code to use to zero out buffer.(DCSG00208365)
-Remove A0 raw fw rawA0.fw file from release scripts.(DCSG00211914)
-SMART Polling Improvement- API Changes.(DCSG00214352)
-Support getting the defaults and supported properties in Auto Config NONE mode.(DCSG00215321)
-SPDM:7.15: Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust.(DCSG00216859)
-MBEDTLS LIB: Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust.(DCSG00216867)
-Addition of atlas_bst scripts.(DCSG00218726)
-XSD :Add New fields 'predFailPollDAInterval' and 'predFailPollInterval' in MPI2_MR_PARAMS_PAGE_0.(DCSG00218900)
-API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI STAT.(DCSG00222915)
-MR PVT API :Update mr_configpage.h file for New fields 'predFailPollDAInterval' and 'predFailPollInterval' in MPI2.(DCSG00223408)
-SPDM_LIB: Support to build Challenge buffer with multiple GET_CERTIFICATE/CERTIFICATE_RESPONSE.(DCSG00225175)
-SPDM python script: Support to build Challenge buffer with multiple GET_CERTIFICATE/CERTIFICATE_RESPONSE.(DCSG00226081)
-Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API.(DCSG00226286)
-Shenandoah - Add Snapdump support for PLDM Type-2 and Type-6 platform modules.(DCSG00226289)
-Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR firmware.(DCSG00227036)
-Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - nvram.(DCSG00228248)
-New MFI Stat for the updated recon behavior.(DCSG00229416)
-MR7 API: Add package incompatibility reporting.(DCSG00231443)
-Add sg_sanitize PT support.(DCSG00232659)
-Aero3: SecureBoot BIOS Image Download with new Key is failing.(DCSG00233694)
-Added power cycle tests in Atlas AutoBST.(DCSG00234319)
-Atlas BST:- USD integration.(DCSG00234348)
-BST setup with Channel HBA + Elrond.(DCSG00234391)
-Implement customSign.exe CLI wrapper utility to help customers sign with their private key(DCSG00234646)
-MR SPDM:7.15: Implement client APIs for SPDM Get Measurement command (in SPDM LIB).(DCSG00234724)
-SPDM LIB: Implement SPDM Get Measurement command.(DCSG00234758)
-Make necessary changes to atlas_bst in valscripts to enable BST for 4.2.145 stream.(DCSG00237302)
-Persisting secureLD targetId bitmap.(DCSG00237413)
-Enable SAS 240K R5 RW on MR7.15.(DCSG00241136)
-SMART Polling Improvement - API Changes.(DCSG00246317)
-Added drive push pull tests.(DCSG00253665)
-Add Atlas Behind Aero Setup in Atlas AutoBST.(DCSG00253672)
-To add return status MFI_STAT_OK_REBOOT_REQUIRED to MR_DCMD_LD_SET_PROPERTIES in mr.h.(DCSG00256271)
-MFI SMP Port Num API changes.(DCSG00257777)
-BST script modification due to change in RO content.(DCSG00265215)
-SecureSign ECDSA: Implement support for elliptical curve signing for SPDM.(DCSG00265812)
-MR PVT API: Add singlePortMultipathFeatures to MPI2_MR_PARAMS_PAGE_0.(DCSG00272230)
-Enable 24 PCIe device support for Aero External boards..(DCSG00278073)
-NVDATA change for Ruby SED support.(DCSG00278286)
-MR PVT API :Update mr_configpage.h file for Ruby SED support.(DCSG00278424)
-XSD: Add New field 'parityReadCacheBypass' in MPI2_MR_PARAMS_PAGE_0 for PR DCSG00237022.(DCSG00282675)
-MegaAPI: Add API Controller Properties and MFCD for ParityReadCacheBypass (PR: DCSG00237022.(DCSG00282676)
-PvtAPI: Add new field 'parityReadCacheBypass' in MPI2_MR_PARAMS_PAGE_0 for PR DCSG00237022.(DCSG00284472)
-MR API: reclassify MR_EVT_CTRL_FW_VALID_SNAPDUMP_AVAILABLE as informational.(DCSG00292323)
-Disable custom image build for HBA BST.(DCSG00301780)
-Update SIGNIMAGEX to v2.12.00.(DCSG00306898)
-XSD : Add New field 'singlePortMultipathFeatures' in MPI2_MR_PARAMS_PAGE_0.(DCSG00310657)
-Vendor requested megamon command to simulate bad flash to be supported all its boards.(DCSG00313349)
-Make updating the embedded key( step 1) of securesign optional..(DCSG00313996)
-Add noembed support to signtools.(DCSG00314237)
-SPDM python script: Add handling to manage actual certificate certain for Aero with depth=4.(DCSG00315798)
-Update dev bst suite..(DCSG00315850)
-SPDMLIB: OEM requested to not report Get Measurement Capable.(DCSG00323053)
-Set disablePdDegradedMedia in all XSDs.(DCSG00324772)
-Add new security events.(DCSG00167311)
-Add boot mode print to log during boot.(DCSG00169640)
-DA-SEP internal backplanes host led management status not correct.(DCSG00176030)
-Host access to internal backplane SEPs.(DCSG00212119)
-Support bit for "cannotExecuteOnce" autoconfig parameter needs to be set as 0 for all configure modes.(DCSG00183076)
-Modify Ventura Build scripts to add a new Signed image with different AVSO Setting in FW RO.(DCSG00231216)
-MR FW changes to use Smart Polling Intervals values from NVDATA.(PR#DCSG00113187).(DCSG00211992)
-SPDM IT: Add memory allocation/free for SPDM_LIB.(DCSG00229260)
-Change to the Powerloss Recovery Sequence to Recover Corrupted BMU Flash.(DCSG00235822)
-Aero Secure Boot: Add Key Update Pending Check for 'COMPLETE' Image Download.(DCSG00241566)
-Enhancement to source of randomness for generating key pair.(DCSG00208477)
-Execute once Auto configure option needs to be allowed for EPD-PT behaviour mode for certain controllers.(DCSG00216966)
-CIO deprecated IOtype display while recon Vd - to be removed.(DCSG00301684)
-Snap-dump Enhancement - remove unnecessary duplicate prints.(DCSG00312222)
-Monitoring Drive Performance and Predictive Failure feature to be removed for certain OEM.(DCSG00082984)


Version 51.15.0-3832 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:7.15.00.0
	UEFI Driver:0x070F0301
	HII: 07.15.04.02
	MR FW: 5.150.00-3429
    package 51.15.0-3832
MR 7.15

Defects:
 -(DCSG00039823)
 - SPDMLIB: Add change to SConstruct to copy library output file (*.a) to release folder(DCSG00117832)
 - Handling a newly added Cache loss Boot Message for IML(DCSG00041692)
 - The test tool does not reflect correct bad block count when additional bad blocks are added(DCSG00139682)
 - SPDM_LIB: Add alignment parameter into SPDMLib_Calloc interface(DCSG00237674)
 - Merge conflict issues(DCSG00234911)
 - NVMe Init reports wrong failure error codes(DCSG00103993)
 - Aero_DBU_7.14_PA2: VMWARE Beta OS reported Assert during data under run.(DCSG00096622)
 - Add new environment variable to enable/disable SPDM feature code prior to RC, GCA, FINAL build(DCSG00415494)
 - Coverity Bugs in PL Enclosure Management Files(DCSG00043514)
 - Additional Key Data field of Security Page 1 is missed in XSD definition(DCSG00077979)
 - Firmware hits exception on power cycling the server with NVMe drives connected(DCSG00109752)
 - Fix unintended update of BBM Long size.(DCSG00148922)
 - MBEDTLS LIB: fix compilation error during IT FW build(DCSG00234920)
 -(DCSG00218427)
 - Adjust the UART messages during Snapdump(DCSG00086774)
 - Allow OEM Aero controller to be able to disable foreign auto import(DCSG00353789)
 - Aero Host Application Loading Changes to Support CTRL-R(DCSG00152618)
 - duplicate entries of arrays when creating hot spare drive caused storCLI to display incorrect information(DCSG00234562)
 - SSD Estimated Life Remaining in Days shown appropriately for nvme drive(DCSG00216327)
 - SPDM: Attestation failed with wrong Nonce values(DCSG00126872)
 - Made platform changes for PLDM fw update operation(DCSG00049608)
 - Fix file names related to PTB(DCSG00081243)
 - 216-x controllers do not have ONFI support, optimized the code.(DCSG00217262)
 - Fix static code analysis defect 127860(DCSG00241065)
 - Adding SPDM filter in client code.(DCSG00062370)
 - VenturaMR 7.14Alpha: -24% drop and 55% gains seen in SDR0, R0 for SW, RW for IO Size-4K-1M, QDs-4,16,64,256 - 64D-12G SAS HDD Expander connect - Linux OS(DCSG00150877)
 - 7.14 SPDM client code fix: Enable Route By ID for all the packet.(DCSG00150120)
 - Change file name of SpdmDebug.h to SpdmDebugs.h . And Check in SpdmDebugs.h for IT(DCSG00074556)
 - UNMAP support is blocked and disabled(DCSG00253426)
 - Aero MR715PA - Aero + Atlas FW download blocks IO causing driver KA and OCR(DCSG00233642)
 - Aero_DBU_714: On Cavium (ThunderX2(R) CPU CN9975 v2.1 @ 2.20GHz) ARM server with Ubuntu OS, Aero discovery fails with megasas_init_fw(DCSG00111965)
 - SPDM 7:15 Set tagOwner as per SPDM request.(DCSG00240237)
 - NVRAM changes for supporting dynamic recon ghost tgtId(DCSG00216908)
 - CTRLH- Incomplete Display of messages(DCSG00301793)
 - SCSI Passthrough format command on unconfigured good drive causes kill adpater(DCSG00150798)
 - Fix assert in etty debug code(DCSG00152802)
 - VD creation with default WB policy to be blocked in P216i Controllers(DCSG00054336)
 - Correct Sblib Int make sure ER 110403 and ER 166877 are present (2)(DCSG00215388)
 - Fix EPD target Id computation logic based on slot ids(DCSG00395632)
 - MBEDTLS LIB: Fix dynamic memory release bug in Mbed Tls Library(DCSG00216944)
 - Mismatch between subsystem id in NVDATA and SBR for 9405-W 16i(DCSG00077700)
 - MR 7.14 : Storcli allows to set maxspinupdrive count to 255.(DCSG00076934)
 - Release Automation: Exceptions during execution of release script(DCSG00151389)
 - Aero A0: External cards do not support more than one PCIe drives.(DCSG00249770)
 - [SPDM] SPDM lib changed one of header file name , seeing compilation error in IT.(DCSG00077919)
 - RDE: Fix operation for volume and link error threshold for port(DCSG00097465)
 - PCIe Switch Page 250 has NumPorts set to zero, and this page is not included in "iop show cfg all"(DCSG00101756)
 - 7.15 Static Analysis defect 186076(DCSG00307838)
 - Implicitly error when converting an expression to a narrower type(DCSG00225977)
 - MR7.15 Alpha: Kill Adapter occurs during flashing enclosure firmware and heavy IOs(DCSG00299407)
 - MBEDTLS Lib: Alignment issues while certificate verification on IT cards(DCSG00312818)
 - Fix static code analysis defect 45959 45944(DCSG00253256)
 - MR7.15: SPDM: Dev DF: Call revised SBLIB API to retrieve Secure ID(DCSG00310427)
 - No Bad Phy reported after inserting a simulated Bad drive(DCSG00051251)
 - Fix for incorrect bay count value.(DCSG00071758)
 - WG: LSA does not allow to change to any other behavior once encountering error during behavior change(DCSG00243910)
 - SPDM_LIB: Set tagOwner as per SPDM request.(DCSG00239464)
 - Remove stale parameters from NVDATA(DCSG00136341)
 - PL: Adjust the MPI Device support check to only support Atlas's MPI Device(DCSG00040939)
 - pl: NVMe: 265D fault in out of resource case(DCSG00093410)
 - MR_7.14 Alpha DBU: Ventura iMR FW received a command "getCdbPtrAndTargetId: Invalid cmd fa", it result to KA on VMWARE OS.(DCSG00151683)
 - MR_7.15: PTB switch to Enabled and Save. No PoP up message reboot required/PTB.txt not part of Snapdump.(DCSG00241021)
 - Phase 15 Coverity Bug Fixes(DCSG00105045)
 - Duplicate MPI Toolbox Tool Values in MPI temp(DCSG00086898)
 - Unknown messages are displayed in LSA event logs and also in termlog on drive removal(DCSG00289940)
 - FW creates R0 VD when HII: Enable/Disable Host LED Management For JBOD setting is toggled(DCSG00095243)
 - FW hits assert when NVMe drive returns non-success reply for admin commands(DCSG00080405)
 - 7.15 Aero MR: Add alignment parameter into SPDMLib_Calloc interface(DCSG00237675)
 - Running format on a EPD once one has started is causing a KA.(DCSG00167682)
 - MR7.15 PA2: drive and enclosure connector are reported differently in Ctrl-R for OEM controller(DCSG00241278)
 - MR 7.15: Invalid Arguments error seen while setting config file w.r.t JBODs from Storcli.(DCSG00221279)
 - PL: Reply to IO's bad SGL to Atlas SES has wrong DevH and SMID's incorrectly tries to fit 3 SGEs inframe(DCSG00315476)
 - iMR boot stuck in creating slot mapping(DCSG00214223)
 - MR7.15: Flashing Atlas RDK firmware via storcli caused MR firmware crash(DCSG00297302)
 - storcli 'start diag': link test skipped if no configured drives present; link test failed if no backend PCIed support(DCSG00328095)
 - Aero MR715PA - Aero + Atlas switch write buffer command fails occasionally(DCSG00241202)
 - RDE - REST client displays ReadCachePolicy as OFF for Read Ahead enabled volumes(DCSG00243670)
 - SBLIB: Getting Inconsistent secure ID on IT cards(DCSG00309847)
 - MR7.14 Beta: BMC-OOB-Update Controller Firmware SLT reports "Flash download already in progress"(DCSG00088074)
 - storcli 'start diag' command failed if ran after storcli 'show all' command.(DCSG00231398)
 - 7.15 Static Analysis defect(DCSG00307840)
 - PTB bad address handling(DCSG00077833)
 - Fix for Data Abort Exception caused due to access of invalid device id in event structure(DCSG00043231)
 - MR 7.15 RC1: Dell Ventura H740 Mini Preboot set Preboot Trace Buffer does not change when setting factory defaults(DCSG00341277)
 - Coverity Defects(DCSG00094727)
 - PH15 Scrutiny CLI: device c command output is not giving the details of the all the devices connected to the expander(DCSG00102332)
 - The first 32 characters of MPI defines should be unique(DCSG00086266)
 - Fix static code analysis defect 127845(DCSG00241066)
 - MR_7.14 PA2 DBU: FW received the KA, while running IO with IOCTL command in a loop(DCSG00117767)
 - Fix Static Code analysis issue 101556 101555 101554(DCSG00084027)
 - pl: backend PCIe: prevent switch rediscovery quirks(DCSG00018730)
 - MR-7.13: FW - STP passthrough -FW sending ack before completely receiving all MCTP packets.(DCSG00078243)
 - MR_7.14_DBU: FW & Storcli reported enclosure id's are mismatch for a NVM-E drive which has failed in nvmeinit(DCSG00099024)
 - MR7.15 PA2: driver health message displayed 1 more time after device order by firmware is disabled on Windows system(DCSG00231084)
 - SPDM : BMC Emulator System is halting at POST with latest FW pkg 2.14.0-3226 with Zumabeach controller.(DCSG00111753)
 - MR 7.15_IO tool detecting data integrity issue on 8i8e controller with NVME and SAS connected to different enclosure/Expander(DCSG00231642)
 - Firmware fails to send Enclosure removal event to host when the enclosure is removed from the topology.(DCSG00232962)
 - [Aero] Application scanning for I2C devices on I2C bus hang when OOB configured to MCTP-PCIe mode(DCSG00103208)
 - NVMe Init error drives are not discovered after pull/push within DMD timeout(DCSG00242197)
 - FW : OCR fails to start from OOB Storelib test, and controller fails to discover in OOB SLT after this failure(DCSG00245029)
 - Sea 16e PCIe TX Compliance Test Failure(DCSG00052179)
 - MR7.15 PA1: excessive "In OOBExecCmdIssue and dmcd is 0x#######" prints seen on termlog(DCSG00152105)
 - Duplicate slot IDs assigned for SAS/SATA drives on elrond Ex1 backplane when it is connected to 9405W 16i controller.(DCSG00072826)
 - Crucial assert print is missing from Snapdump(DCSG00139459)
 - Ventura/Mercator: pl: 4311 fault following SAS IO Unit Page 1 write(DCSG00099275)
 - PL Backend PCIe: 0xEE1A fault observed with bad clocked Aero and Atlas(DCSG00080298)
 - Firmware Fault on iMR while running IOs on 4K sector drives(DCSG00108060)
 - BSOD observed with mode 7 Parallel PD firmware update in PCIe OOB(DCSG00315988)
 - Controller fault observed on changing some phys to manual port config with port set to 0.(DCSG00237498)
 - Ventura: SAS3616W or SAS3616W based boards have links less than epected width(DCSG00249594)
 - SPDM_FW : Import certificate should fail for the slots for which already certificates are imported and sealed(DCSG00119529
 - Place oem specific event logging introduced after Boot Message under OEM check(DCSG00397695)
 - MR 7.15 Alpha: securesed property can be set but not shown under show personality cmd for NONE mode(DCSG00257803)
 - Elrond Ex2 w/ SAS/SATA incorrect slot numbers after PD move to different slot(DCSG00069084)
 - 7.15 Aero: Call SPDMLibInit only if SPDM is enabled.(DCSG00231374)
 - Correct Sblib Int make sure ER 110403 and ER 166877 are present(DCSG00214265)
 - Fix static code analysis defect 127882(DCSG00253339)
 - pl: backend PCIe: resource leakage during direct attached event generation(DCSG00093660)
 - FW : Observing fatal FW error at Line 169 in fw\raid\utils.c on drive removal in a 240 VD configuration.(DCSG00324755)
 - Use slot group number to get certificate algorithm record of security manufacturing page(DCSG00232583)
 - Fix for the value of a controller status bit: Support PD firmware download(DCSG00109367)
 - Fix Spdm Client logic(DCSG00053777)
 - Controller Delete DPMStat Type=all does not reset QD.(DCSG00096734)
 - RDE - Storage Controller cache health status should display "Warning" if WB cache enabled Volumes present but energy pack is failed, missing or charging(DCSG00115184)
 - 7.14 PA2 (DBU) LSA WG: No option to change the behavior mode for the Ventura controller.(DCSG00109936)
 - MR7.14: Controller Bios never sent the printing-has-completed DCMD(DCSG00212592)
 - Snapdumps are discarded unnecessarily when flashing a new ROP(DCSG00118659)
 - Make it easy to query PTB wrap(DCSG00079652)
 - SBLIB: Significantly longer boot times that previously encountered in MR CBB(DCSG00299427)
 - UBM3_x4-Solid Green LED turned on on JBOD drives after few drive pus pulls(DCSG00085866)
 - Add PCE register dumps to snapdump(DCSG00218199)
 - pl: port enable is delayed when SAS/SATA devices are attached to a UBM backplane(DCSG00076783
 - Performance regression in various workloads due to code arrangement (4K SW QD=64 RAD6 1W for 24 SAS SSD and SR profile for small IO size in all QDs in 12G SAS HDD)(DCSG00073978)
 - System POST not proceeding and keeps on loading EFI SAS driver(DCSG00287132)
 - RDE -"Volumes@odata.count" is coming up as 0 for a Dedicated Spare drive which is part of a Volume(DCSG00112594)
 - Add a build option for Coverity MISRA_CAST to disable CWE-681(DCSG00079268)
 - Out of bound memory access when assigning dma group for controller devices.(DCSG00243152)
 - Manage PCIe Interface page should be greyed out for UBM if the user is not allowed to make any Link Width changes(DCSG00251554)
 - Aero MR7.15 PA - Aero+Atlas Eval Invalid enclosure and slot info from nvmeiniterrorlist(DCSG00151747)
 - Junk character is display in OEM serial number(DCSG00084472)
 - Phase 15 Coverity Bug Fixes(DCSG00092935)
 - Connector Name displayed as 'Unknown' in HII for NVMe drives behind Switch(DCSG00085845)
 - 0x6001 Fault while running IOs and cable pull test(DCSG00040422)
 - Evaluate the MFI stats returned with the updated recon behavior(DCSG00227245)
 - Fix the decision in zcdump for which context to run in(DCSG00225050)
 - IOP: Trace buffer image has extra "CFG string(DCSG00051124)
 - Backplane expose on/off setting is failing(DCSG00075666)
 - (SATA Only) SCSI ATA Passthrough command with set feature command to set the drive in standby_y state sets it to standby_z state.(DCSG00080256)
 - MR 7.14 : Unable to set controller properties with latest aero firmware pkg using storcli(DCSG00094728)
 - MR 7.15: SPDM: Select correct Hash Algo for CSR (Certificate Signing Request) & close CSR session for error case(DCSG00304511)
 - 9580-16i controller with PCIe switch doesnt see fault LED on offline PD(DCSG00224982)
 - Check in SpdmDebug.h for IT(DCSG00074108)
 - Updated CoreDump specific functions to run from OCM memory and enabled XMEMXOPY(DCSG00093703)
 - pl: NVMe: E429 fault on register read failure(DCSG00098345)
 - SBLIB: Change bool type to int type in API parameter to maintain compatibility(DCSG00100308)
 - SPDM: Don't fail APP request for import certificate in slot 2-7 with sealed flag set(DCSG00108408)
 - Enable SSD Wear Gauge for NVME drives(DCSG00042403)
 - SPDM library to remove %s for any print as IT does not support %s print string.(DCSG00061353)
 - JBOD deletion event id 139 has slot id 255(DCSG00299050)
 - Import certificate command with out seal option is failing for slots 0 & 1.(DCSG00228127)
 - [Aero/Ventura] MCTP discovery fails after unload and load of MCTP driver in BMC(Board Management controller)(DCSG00058897)
 - ventura build issue with PL PCI DEVICE feature disabled(DCSG00286358)
 - OEM board: SAS drives the link speed is shown as unknown(DCSG00110319)
 - RDE : Query for drive information which was part of volume where full initialization was running results in unexpected error in REST client(DCSG00112022)
 - Total Device count mismatch(DCSG00048491)
 - SPDM: Dev DF to check in a new environment variable to control disable/enable hard-coded key pair(DCSG00324022)
 - Fix iMR save code in create small dumps(DCSG00113527)
 - A8: Aero MR 7.14: Intermittent issue: Assertion failure in fw\raid\taskman.c at line 361 , when tried to start IO's on SAS SSD 24 expander connect RAID5 RW Windows 2019(DCSG00139362)
 - MR 7.14 Beta: Assertion failure in fw\raid\mpthostcmd.c at line 3213: crd->mptReqDesc.Default.SMID(DCSG00215378)
 - Update log function to match API changes for event structure(DCSG00098168)
 - MR7.15 PA2: JBOD is missing after downgrading to 7.14 FW and upgrading again(DCSG00230227)
 - MR7.15 PA1: Downgrading to 7.14 FW when device order by firmware is enabled causes controller to be not accessible in OS(DCSG00221705)
 - Expander FW fail to flash FW sometimes in offline mode(DCSG00217264)
 - Starting initialisation while CC is onging is causing Test script to fail(DCSG00226019)
 - Return MFI_STAT_NO_HW_PRESENT for some bbu DCMDs for 216 controllers(DCSG00081956)
 - Make Clear of the PEPP version of ConfigValid Applicable to IT Boot Code Only(DCSG00398453)
 - The "Last Erase Block' reported in the debug data is incorrect.(DCSG00170637)
 - Fix static analysis issues(DCSG00087285)
 - Pre-boot crash snap dump is not fully captured(DCSG00297597)
 - PL: MS-SES with no Array Devices in Atlas SES causes 0x7200 fault(DCSG00077263)
 - Fix SPDM routines name which are using same name as PLDM routines(DCSG00079768)
 - Unitialized pointer was being accessed(DCSG00096545)
 - MR_7.15: User disabled PTB not reflected, hence PTB.txt is part of OnDemand SnapDump(DCSG00238510)
 - SPDM LIB: Set ECDSA signature with correct size in Signature field of SPDM Challenge response buffer before sending to BMC server(DCSG00225192)
 - Disabling MR_CTRL_INFO.ldOperations.writePolicy bit in JBOD mode for specific OEM(DCSG00069218)
 - MR 7.15 Alpha - Large IO Support is allowed to be changed, but can't be set(DCSG00304321)
 - Parallel PD Firmware hang once interrupted and restarted from SLT in OOB PCIe mode(DCSG00108848)
 - SPDM_FW : SPDM commands are failing in OOB SL/SLT on Trinity M6 servers.(DCSG00126744)
 - PD FW Download support bit is repurposed to FW Download in progress(DCSG00138303)
 - Aero MR FW: While reconstruction process is running in the background, Firmware is allowing to change the behaviour mode from NONE to R0 with error message.(DCSG00108800)
 - Drive count not correct in CLI for UBM3 x4 backplane with SAS drives connected(DCSG00081735)
 - PL: Aero -- Atlas US Cable Pull/Push Results in Missing Enclosure Slot Info(DCSG00181448)
 - crypto erase not completing on SATA drives(DCSG00256740)
 - PL Fault 0xEA11 observed, while upgrading Atlas FW using StorCLI in presence of bad NVMe PD's present in the Atlas.(DCSG00324838)
 - Coverity found defect in MPI Device and FPE modules.(DCSG00098787)
 - MR 7.15 PA2: Extra prints not seen before that appear to be debug: setup_cache_headers(DCSG00228849)
 - MR7.14 Beta: Firmware hit exception stuck while IOs and rebooting, causing no controller found(DCSG00215476)
 - Fix mistaken warning of drive degradation detection messages(DCSG00212751)
 - Firmware faults when reconstruction is going on with cable pulls(DCSG00134460)
 - Make PLDM platform code compiling without OOB_COMMON(DCSG00219528)
 - NVME Drives not getting discovered on inserting in Customer UBM3 x4 backplanes until OCR.(DCSG00081732)
 - Cache Vault failures on 9560-8i(DCSG00416955)
 - Aero MR 7.14 PA2: Win/Lin Gen4 NVME: -15% drop seen in OLTP profile for IO Size-256K from QD-64 to QD256 in R0-1WRK(DCSG00137117)
 - Avoid data exception when collecting early preboot snapdump(DCSG00081566)
 - Observed Data Corruption during IO stress test.(DCSG00212797)
 - Bug Fix for SPDM modules(DCSG00103063)
 - OOB : Controller is not discovering thru OOB Storelibtest in pcie mode on loading /unloading SLT multiple times.(DCSG00166684)
 - Aero A0: Fault D033 running IO + Expander Phy Link/Hard Resets to Expander phys(DCSG00045450)
 - Energy pack moves to failed state post controller reset(DCSG00046787)
 - Addressing IT raise defects in SPDM library change.(DCSG00061718)
 - Fix offset comments in DM IO Context(DCSG00226222)
 - Large topology of more than 500 drives cannot be supported on SAS 3.5 Channel Controllers(DCSG00108246)
 - Phase 15 Coverity Bug Fixes(DCSG00104982)
 - SPDM DCMD bug fix 03/04/20(DCSG00103877)
 - On trying to import more than 240 VDs , foreign import fails with " incomplete foreign config " error message.(DCSG00306596)
 - IT SPDM commands not working via host interface(DCSG00134673)
 - traceTool.py improvements from assert auditing(DCSG00358708)
 - MBEDTLS LIB: Add change to SConstruct to copy library output file (*.a) to release folder(DCSG00117834)
 - MR7.15 Alpha: JBOD drive still show and list as first in order device before VD even after system reboot (Jbob personality mode)(DCSG00304336)
 - Coverity Defects in SATA and VPP code.(DCSG00234415)
 - MFG Page 49/50/51 defines are not compiled(DCSG00083748)
 - MR7.15 Alpha (DBU) WG: LSA allows user to assign drive in prepare for removal state as replacement for missing drive for a DG(DCSG00255186)
 - Add OEM checks for internal OEM specific structures and code(DCSG00397741)
 - Aero: PswSbr.bin file is read only and causes an error when running the RMC script(DCSG00082963)
 - [Aero] SATA drive gets dropped when corresponding phy is disabled and enabled.(DCSG00222544)
 - PL: SMP Timeouts During Expander Phy Reset Test(DCSG00043616)
 - Fix static code analysis defect 127973(DCSG00241062)
 - RDE - REST client displays drive state as "Disabled" when initialization is running on the Volume configured on that drive(DCSG00223283)
 - [9440-8i+MR7.12/7.13/7.14Beta2+ARM] controller FW printed Assertion failure in fw\cpu\arm\exceptions.c at line 1006: 0 during fio issue verify(2F) commands to sas hdd(JBOD)(DCSG00236990)
 - (MS SES) Non data transfer SCSI IO failed with Invalid SGL error(DCSG00234926)
 - iMR FW may crash if disabled in device manager when Microsoft OS boots and lock up(DCSG00040869)
 - MR-7.13: FW - STP passthrough response Firmware does not send some ending bytes.(DCSG00078207)
 - The last known successful learn time is reported as in Nov 11, 2000(DCSG00107714)
 - RDE - Make Redfish Tool compatible with python 2(DCSG00166025)
 - Fix Bus Master Enable handling in Snapdump related to DCSG00040869(DCSG00112203)
 - NVMe device not discovered after disable-enable PCIe link in PCIe IO Unit page 1(DCSG00082524)
 - In JBOD personality SES management bit is not set in auto configure supported bits for NONE Mode(DCSG00278401)
 - MR 7.14 Beta: OCR did not complete appropriately and assert didn't print properly(DCSG00212038)
 - Fix stack printing in "ef" command(DCSG00171225)
 - Fix print nesting for ASCII eTTY(DCSG00134926)
 - Controller fault 0x1902 is seen while issuing locate command to NVMe drives(DCSG00062252)
 - MR7.15: FW hit Assertion failure in fw\raid\fwDownload.c at line 1159: fwDownload.pdRestrictCount!= 0 while flashing encl & PD firmware correspondingly(DCSG00283749)
 - Fixing Coverity issues(DCSG00096489)
 - 512B drive is assigned as DHSP for 4K DG(DCSG00079486)
 - Aero MR7.15 Alpha - PR stalls, never completes on NVMe PDs(DCSG00267705)
 - Timestamp is not getting established in Atlas FW, when Atlas is connected behind Aero Controller(DCSG00268587)
 - "Add enclosure event for an enclosure that is already active" error message observed in Windows event logs(DCSG00063929)
 - Aero Pre-man string failure during looped testing(DCSG00084540)
 - GetSchemaDictionary command executed from RedACT is failing for annotation schema(DCSG00078890)
 - Disable R0 Autoconfig option from FW(DCSG00109751)
 - iop show cfgspace doesn't work(DCSG00066110)
 - SPDM LIB: Need to include header file SpdmLibTypes.h in SpdmLibIFace.h(DCSG00074328)
 - MR7.15 Dev: reduce dmSpinCheckAndRetryCmd etprints.(DCSG00228143)
 - MR 7.14 Alpha: Unexpected OCR caught by automation, FW update issue(DCSG00138244)
 - OEM Server: Foreign Secure Drive - Clear drive option is Enabled.(DCSG00282684)
 - Fix MR MPB2 copied length.(DCSG00099487)
 - MR 7.14 PA2 - Aero firmware asserted at taskman.c at line 361 during R5 SED creation(DCSG00111382)
 - MR 7.15 Alpha: PR estimated time left is wrong in multiple places(DCSG00297903)
 - Bug Fix In get CERT and While reading the certificate from the client(DCSG00047643)
 - ED91 Fault while running IOs + OCR (controller reset) testing(DCSG00057254)
 - print correct variable during error condition(DCSG00096538)
 - RDE - "EncryptionAbility" field for SED drives displays blank(DCSG00237493)
 - Controller DPM type= hist does not save Response time properly which shows some conflicts.(DCSG00086932)
 - For Vses device box info is populated.(DCSG00045198)
 - Applications displays incorrect PD count with SATA drive in enclosure on multi-path configuration(DCSG00151556)
 - Fix PD initialization abort issue on non secure erase SATA SSD(DCSG00137138)
 - Asserts from interrupt handlers are not working properly(DCSG00127828)
 - Use NVRAM to save PTB information(DCSG00079654)
 - Remove MR's EXT_MFG_49 define. This change should be pick up from DCSG00228036 Pre-Alpha Release: CtrlFw_Ph_16.0 - 15.250.05.00 MR PL-SCS Libs(DCSG00229397)
 - Fix for misalignment of an internal structure(DCSG00050922)
 - MR 7.14 PA2 DBU : SLT_OOB : Get enclosure element data throws 8017 error code for UBM backplane.(DCSG00121827)
 - Controller DPM overflows Write Count after 32 bits. As per document, it is supposed to be 64-bit number.(DCSG00103860)
 - Coverity defect fix(DCSG00231928)
 - Fix static code analysis defect 128532(DCSG00241025)
 - SPDM 7.15: Dev DF - return appropriate error to SPDM Lib when read certificate from security page 0 fails(DCSG00298150)
 - Avoid controller firmware freeze due to one particular vendor's SATA TCGe drive behavior(DCSG00102153)
 - MR_7.14 Alpha DBU: VMWARE reported IOMMU fault detected for vmhba3(Ventura IMR).(DCSG00149010)
 - MR7.14 iMR snapdump start from ID 1 where MR start snapdump ID 0-- not consistent(DCSG00108698)
 - RDE - Drive schema shows operations as "Erasing" and percentage "0" after initiating LD erase/initialization operation(DCSG00134506)
 - Fix static analysis defect(DCSG00226155)
 - event ID 458 is truncated as: Write-thro instead of Write-through(DCSG00382760)
 - MR7.15 PA: FW gets hung while generating snapdump through MegaMon call SnapDumpDbgGlobalOnly(DCSG00220882)
 - MR 7.14: Storcli: "Support NVMe Repair" is shown as "yes" in profile 10 and incorrect raid support displayed in profile 11 on iMR ventura(DCSG00099915)
 - SPDM_FW : Delete/Import foreign configs should not be allowed until SPDM Authentication happens between BMC and controller.(DCSG00237704)
 - Coverity found defect in SATA and Enclosure management modules.(DCSG00098596)
 - RDE - REST Client displays truncated drive size for NVMe drives(DCSG00148309)
 - Make Challenge Buffer Include Get_Digest/Digest, Get_Cert/Cert(DCSG00055393)
 - Controller DPM (Drive Performance) returns some unacceptable numbers.(DCSG00080749)
 - Failed NVMe drive repair start command does not get report back properly(DCSG00134906)
 - controller DPM type=Ext returns wrong number of sectors.(DCSG00088148)
 - SPDM 7.15: return actual size of certificate chain content to SPDM LIB(DCSG00226169)
 - Disable CoreDump when Flash device is not present(DCSG00054500)
 - Correct tagowner for Spdm Client MCTP code(DCSG00061087)
 - Adapter got killed when trying to update Atlas FW using storcli with IO(DCSG00231406)
 - Build failed after MbedTLS new base line pulled(DCSG00074952)
 - RDE - Firmware crash observed after querying LD information from REST client on AROC controller(DCSG00151330)
 - Observed PL Fault 0xEE17 when NVME drives connected via PCIe switch.(DCSG00108281)
 - SPDM: DF: Remove calls to Mbed TLS Self-Test functions(DCSG00335761)
 - Shenandoah RDE: Fix PCIe interface details(DCSG00080093)
 - Fix incremental Coverity builds(DCSG00254162)
 - [MBEDTLS] Device Key Pair Generation resulting in different Keys on IT card(DCSG00318909)
 - RDE - "StripSizeBytes" shows double the actual strip size value for the volume resource in REST client(DCSG00136280)
 - MR7.14 PA2 - Unable to collect zcdump once hitting PL Fault. FW keeps looping back to PL Fault again.(DCSG00109086)
 - Some of SAS/SATA drives attached to OEM Aero HBA may not be reported to host(DCSG00076717)
 - pl: firmware hang occurs in UBM command error case(DCSG00072841)
 - Coverity defect fix in FPE code.(DCSG00235474)
 - Atlas 4.2: Prints "C0:EnclSesPdAccessAllowed: SES not ready (opState:10000) pd:0" observed in Aero FW logs, after upgrading/downgrading the Atlas RDK FW which is connected behind Aero controller(DCSG00254663)
 - Resetting the event counters in Ext. SAS/PCIe IO Unit Page 250 fails(DCSG00150901)
 - Fix SPDM library for Get_Digest, Challenge.(DCSG00053409)
 - RDE - Virtual drive 'PercentageComplete' shows 100 in REST client for volume resource when erase operation is running(DCSG00113953)
 - [SPDM] Fix compilation #include "iopPlatSecCertMgMt.h" case sensitive issue(DCSG00109315)
 - SPDMLIB: Reduce number of arguments passed to IT FW debug print functions(DCSG00335615)
 - SPDM: Fix issues in Certificate Slot Mgmt DCMD(DCSG00103123)
 - Fix and Rename Common NVMe Header File(DCSG00025545)
 - Release Automation: Web page button not detected in script.(DCSG00137712)
 - Fix static code analysis defect(DCSG00241024)
 - pl: NVMe: D062 fault during NVMe init(DCSG00083594)
 - MR7.15 PA1: VDs missing after upgrade/downgrade between MR7.14 FW and MR7.15 FW(DCSG00216224)
 - Aero 7.15 MR: Add memory allocation/free for SPDM_LIB(DCSG00226196)
 - MR7.15 PA1: Enclosure disappears after back to back ESM FW update with IOs(DCSG00171108)
 - Correct Nvme Double Buffer module for multiple double buffer cases.(DCSG00120410)
 - RDE - REST client displays error when tried to get drive resource details on a AROC controller(DCSG00125938)
 - PL: Removal of NVMe Drive that Failed NVMe Init Doesn't Work Correctly(DCSG00103998)
 - PBP hotplug drives showing dual sas address, instead of single sas address(DCSG00096702)
 - FW changes to support removal of "Bays on port" field in APPs(DCSG00082494)
 - MR_7.15: Driver load/unload result to Assertion failure in fw\hw\debug\ptb.c at line 618: 0 on Aero card(DCSG00238473)
 - Aero Seeing "SpdmReadCertForSlot[277]:[Error] Certificate Read Failed" on IT card after Controller Resets(DCSG00253315)
 - Aero SPDM Policy: Add Nvram flag to enable/disable SPDM feature in megamon(DCSG00112274)
 - 4K VD is set to boot device after foreign config import(DCSG00099273)
 - PL: Initial MPI driver error injection can cause the Managed Switch's SES to not be exposed to OS(DCSG00045593 (Port Of Defect DCSG00045725)
 - SMART trip drive LED not blinking for specific OEM controllers(DCSG00084535 (Port Of Defect DCSG00093720)
 - "iop show cfg all" command captured by core-dump is zero(DCSG00047928 (Port Of Defect DCSG00050673)
 - pl: backend PCIe: switch rediscovery fails with certain switch configurations(DCSG00061635 (Port Of Defect DCSG00062706)
 - PL NVMe : NVMe repair operation fails with metadata(DCSG00112303 (Port Of Defect DCSG00121425)
 - As part of the Device Add\Removal Event, the enclosure handle passed on by the PL FW to the upper layer is incorrect.(DCSG00298128 (Port Of Defect DCSG00303518)
 - Auto Configure EPD-PT set fails when sent with MR_AUTO_CFG_PARAMETER received from firmware for Auto configure Off mode(DCSG00215315 (Port Of Defect DCSG00225974)
 - Unable to secure EPD in EKM mode after reporvisioning(DCSG00074490 (Port Of Defect DCSG00082148)
 - VSES SES Page 02h reports Unknown (06h) Element Status for some Array device elements in a wide DFC slot(DCSG00069091 (Port Of Defect DCSG00086818)
 - Autoconfigure R0 is allowed to be set when this should be disabled and only allow the immediate command.(DCSG00078527 (Port Of Defect DCSG00082103)
 - Foreign configuration import fails after rekey operation.(DCSG00104797 (Port Of Defect DCSG00218454)
 - JBOD drive is converted to Configured Drive after OCR / Reboot(DCSG00293760 (Port Of Defect DCSG00312022)
 - UBM: Incorrect slot number enumerated for a DFC on 3 x4 DFCs UBM config(DCSG00048027 (Port Of Defect DCSG00048742)
 - Auto Configure R0 option is showing in eHBA mode(DCSG00235390 (Port Of Defect DCSG00237305)
 - Dev-Defect: Incorrect default autoconfig parameters are returned for non zero confmode(DCSG00111423 (Port Of Defect DCSG00117784)
 - MR7.15 PA: FW gets hung while generating snapdump through MegaMon call SnapDumpDbgGlobalOnly(DCSG00220882 (Port Of Defect DCSG00235639)
 - In JBOD profile, set VD Write Cache to AWB shows success even though WB Supported is set to NO(DCSG00113956 (Port Of Defect DCSG00240942)
 - Dev-defect Use of OEM check in a function not correct.(DCSG00119796 (Port Of Defect DCSG00122767)
 - PL NVMe : PCI task management is not getting completed.(DCSG00231422 (Port Of Defect DCSG00245538)
 - StorCLI shows "PR excluded VDs" where actually PR is running on online PDs of VD.(DCSG00126725 (Port Of Defect DCSG00240684)
 - pl: NVMe: incorrect sense key is returned for Access Denied NVMe status(DCSG00063924 (Port Of Defect DCSG00069167)
 - Ventura: The host PCIe link width may be narrower than expected(DCSG00078678 (Port Of Defect DCSG00093473)
 - Host utility can still manage LEDs when downgrading from FW with jbodhostledmgmt enabled to FW with jbodhostledmgmt disabled(DCSG00230907 (Port Of Defect DCSG00240950)
 - Aero MR7.16PA - snapdump hang during capture in Legacy BIOS(DCSG00318700 (Port Of Defect DCSG00319426)
 - Drives connected behind external card with VSES disabled, failed to detect in Linux OS(DCSG00350402 (Port Of Defect DCSG00366257)
 - COL Failure on AC cycle(DCSG00132764 (Port Of Defect DCSG00143276)
 - Some of the drives not listed under Widows OS Disk Management.(DCSG00096508 (Port Of Defect DCSG00102661)
 - Some of the JBODs are not included under "PR excluded VD" , while performing storcli /cx show pr when all the drives are converted to JBOD.(DCSG00126731 (Port Of Defect DCSG00240682)
 - Auto R0 Available in eHBA mode, Fails when selected(DCSG00079651 (Port Of Defect DCSG00082123)
 - FW fault seen during server bootup.(DCSG00345176 (Port Of Defect DCSG00409078)
 - Expander_FW : Expander FW upgrade or downgrade through CIMC is not getting reflected on host applications(DCSG00171248 (Port Of Defect DCSG00228310)
 - pl: NVMe: Drive Firmware update fails on mode 0xE(DCSG00044028 (Port Of Defect DCSG00052008)
 - Back out changes of ER DCSG00029633 that limits VSES devices to 2(DCSG00053379 (Port Of Defect DCSG00054368)
 - Parameter changed event is not generated after changing autoconfigure behavior from Off to non-raid disk(DCSG00370382 (Port Of Defect DCSG00399183)
 - Atlas Behind Aero: PL Fault 0xEC1A When Performing Backend PCI Resets From Diagnostic Code(DCSG00042688 (Port Of Defect DCSG00147003)
 - BSOD when running CoreDump with Aero connected to Atlas switch(DCSG00042497 (Port Of Defect DCSG00044353)
 - Incomplete foreign configuration when importing LKM into EKMS environment(DCSG00068694 (Port Of Defect DCSG00072326)
 - Fail to read device and link related counters from Page 250(DCSG00080856 (Port Of Defect DCSG00096620)
 - Critical Boot messages not being handled properly during OCR(DCSG00098242 (Port Of Defect DCSG00105198)
 - Aero: Firmware Download should return success with loginfo indicating POR is necessary(DCSG00055371 (Port Of Defect DCSG00065882)
 - In JBOD profile, set VD Write Cache to AWB shows success even though WB Supported is set to NO(DCSG00113956 (Port Of Defect DCSG00240943)
 - PL: Over 250+ power cycles of managed switch (Atlas) causes an associated SES to be inaccessible(DCSG00048699 (Port Of Defect DCSG00059743)
 - [Aero][PLDM] FW version reported wrongly to BMC( Board Management Controller) over out of band(DCSG00050201 (Port Of Defect DCSG00051130)
 - Duplicate event messages are coming in storage logs while scheduling consistency check(DCSG00379811 (Port Of Defect DCSG00408168)
 - [Aero/Ventura] Unused phys are managed by VSes in SGPIO BP mode(DCSG00151021 (Port Of Defect DCSG00225221)
 - PERC 10.5 FW version missing in /c0 show and Hii(DCSG00069395 (Port Of Defect DCSG00072332)
 - SPDM_FW : SPDM commands are failing in OOB SL/SLT on Trinity M6 servers.(DCSG00126744 (Port Of Defect DCSG00220869)
 - Controller fault on rebuild and IO(DCSG00314225 (Port Of Defect DCSG00342265)
 - Aero: backend PCIe: link failure after PCIe IO Unit Page 1 link disable(DCSG00050164 (Port Of Defect DCSG00051710)
 - pl: NVMe: EC0E fault after drive pull during NVMe init(DCSG00114179 (Port Of Defect DCSG00127917)
 - The personality behavior=None is allowed to be set.(DCSG00079271 (Port Of Defect DCSG00082101)
 - Unsupported drive LED Solid Green on Rear Backplane - LED flashing green expected(DCSG00130055 (Port Of Defect DCSG00221408)
 - Cli utility allows auto config option when it is not supported(DCSG00119468 (Port Of Defect DCSG00220685)
 - 0xD101 Fault observed running non-RW IOs to NVMe devices with drive push-pull(DCSG00062701 (Port Of Defect DCSG00071043)
 - PH14 Windows Driver: on 2016,19H2 OS,Getting BSOD for fault command(DCSG00048607 (Port Of Defect DCSG00053744)
 - SEKM: Cannot Secure VD once VD is created(DCSG00087745 (Port Of Defect DCSG00093722)
 - Command to get ld Allowed Ops Ext can be called with wrong buffer length.(DCSG00223430 (Port Of Defect DCSG00246019)
 - Drives returns incorrect session name in SEKM environment(DCSG00229451 (Port Of Defect DCSG00242932)
 - [NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive(DCSG00136092 (Port Of Defect DCSG00243680)
 - [9460-8i+MR7.12 Patch+X86] Use script to upgrade Huawei-made SAS SSD firmware underneath 9460-8i (7.9, 7.11, and 7.12) will fail(DCSG00124592 (Port Of Defect DCSG00240578)
 - [9460-8i+MR7.12 Patch+X86] Use script to upgrade Huawei-made SAS SSD firmware underneath 9460-8i (7.9, 7.11, and 7.12) will fail(DCSG00124592 (Port Of Defect DCSG00240573)
 - NVMe drive hotplug discovery of Ugood drives taking longer (1 minute)(DCSG00313017 (Port Of Defect DCSG00378629)
 - 9460-8i faults repeatedly at fw\raid\utils.c(DCSG00265811 (Port Of Defect DCSG00334584)
 - MCTP: SenseData not available for a failed command sent over OOB.(DCSG00054655 (Port Of Defect DCSG00057485)
 - Number of initiators gets decremented to 0xFF(DCSG00051990 (Port Of Defect DCSG00053834)
 - Quotes present in NVDATA XMLs(DCSG00045528 (Port Of Defect DCSG00045606)
 - Attempting to enable Host LED Management option fails in HII.(DCSG00075900 (Port Of Defect DCSG00082099)
 - FW exception when get snapdump is initiated(DCSG00069689 (Port Of Defect DCSG00077079)
 - Locate PD fail on SGPIO enclosure when GroupId is disabled in Nvdata.(DCSG00034489 (Port Of Defect DCSG00041403)
 - Fault 0x6109 while running IOs and device remove test.(DCSG00082201 (Port Of Defect DCSG00083887)
 - [Aero/Ventura]Allow the backplane detection state machine to retry the FRU detection.(DCSG00219908 (Port Of Defect DCSG00222984)
 - Disable break mirror support(DCSG00147889 (Port Of Defect DCSG00216978)
 - (SATA Only) MODE SELECT (6|10) to SATA drive with DEXCPT set fails if DEXCPT is already set.(DCSG00131574 (Port Of Defect DCSG00134494)
 - AUTOCFG parameters- EPDParams is set incorrectly for NONE/OFF mode(DCSG00127771 (Port Of Defect DCSG00220705)
 - Inadvertent stack printing present at pd insertion(DCSG00365832 (Port Of Defect DCSG00386300)
 - CLI allows auto configure R0 immediate command in ePD pass-through mode(DCSG00119569 (Port Of Defect DCSG00122765)
 - For an OEM - Unable to pause Patrol read via perccli(DCSG00059007 (Port Of Defect DCSG00078513)
 - Auto Secure SED failure status is different in 2 different generation controllers.(DCSG00227232 (Port Of Defect DCSG00240947)
 - HGST Vela-A drive failing media error tests.(DCSG00232413 (Port Of Defect DCSG00325834)
 - PL: TM Device Reset to NVMe drive under out of LMID condition can cause Data Abort Exception to the processor(DCSG00036763 (Port Of Defect DCSG00048676)
 - Change adapterOperations5.supportNvmeWidths to 0 as NVME is not supported(DCSG00111498 (Port Of Defect DCSG00114403)
 - Index out of range is observed for print in ring buffer logs(DCSG00134669 (Port Of Defect DCSG00139071)
 - After loading aero driver, the VD of the controller cannot be listed(DCSG00297806 (Port Of Defect DCSG00311840)
 - 9460-16i MR FW marks Zoned Out PHYs as bad PHYs(DCSG00318971 (Port Of Defect DCSG00329429)
 - Virtual drives offline during Ibanez HBA firmware upgrade/downgrade test using storcli(DCSG00343804 (Port Of Defect DCSG00411425)
 - PL Fault 0000e40e while booting OS with bad NVMe drive(DCSG00109053 (Port Of Defect DCSG00118379)
 - NVMe devices VPD page 83 NAA descriptor may conflict with EUI64 ID reported(DCSG00060347 (Port Of Defect DCSG00136105)
 - Assertion failure in fw\raid\fwDownload.c at line 1182 observed, while downloading the Atlas FW in "Atlas Behind Aero" configuration(DCSG00354677 (Port Of Defect DCSG00366042)
 - SATA Only: Command timeout observerd on SATA drives(DCSG00344039 (Port Of Defect DCSG00356006)
 - MR Ventura FW in JBOD mode still allows security erase by hdparm(DCSG00104151 (Port Of Defect DCSG00119639)
 - Fix ring buffer decoder's slowness with decoding a trace buffer(DCSG00050675 (Port Of Defect DCSG00051120)
 - In RAID personality autoconfig off mode should not be displayed(DCSG00077812 (Port Of Defect DCSG00082120)
 - Aero MR 7.17PA - After SMC legacy bios boot message, snapdump content is missing(DCSG00412164 (Port Of Defect DCSG00423860)
 - Autoconfig paramter Set Auto R0 Mode is not set correctly for eHBA personality.(DCSG00081229 (Port Of Defect DCSG00082135)
 - NVMe drives not discovered and Event replay in enclosure slot mapping not working as expected.(DCSG00078212 (Port Of Defect DCSG00080846)
 - Firmware asserts during customer specific UBM Backplane enumeration.(DCSG00058770 (Port Of Defect DCSG00061183)
 - Direct attached PFA drive - LED is neither ON nor Blinking(DCSG00111492 (Port Of Defect DCSG00143188)
 - NVMe Sanitize completion path and print message modifications(DCSG00080240 (Port Of Defect DCSG00082133)
 - AXI access error from TxDMA engine when certain errors occur during Task Management processing(DCSG00078508 (Port Of Defect DCSG00235435)
 - [Aero][AutoPort Enable] Erase persistent config pages is not retaining the VPD and sas address(DCSG00074378 (Port Of Defect DCSG00114250)
 - [Aero][PLDM] Update to Latest PLDM library v13(DCSG00137629 (Port Of Defect DCSG00138016)
 - Import certificate command is failing via In-band(DCSG00212544 (Port Of Defect DCSG00215132)
 - [VSes] Element status set to 'Unknown' in SES page 2 of VSES for some phys where nothing is connected.(DCSG00333163 (Port Of Defect DCSG00343846)
 - Fix Opal function to relock PD(DCSG00409615 (Port Of Defect DCSG00420418)
 - MR 7.16A controller continuously dumps unexpected sense 7/20/02 for a Jbod and the drives cannot be erased.(DCSG00363682 (Port Of Defect DCSG00395386)
 - FW not checking bound on tty read DCMD, leading to send tty log twice.(DCSG00134946 (Port Of Defect DCSG00220843)
 - Combination of Expander FW update and OOB inventory commands leads to Data abort exception.(DCSG00417301 (Port Of Defect DCSG00428330)
 - Aero A0: In Windows OS redundant disks detected when controller connected to Elrond Ex1(DCSG00061406 (Port Of Defect DCSG00065448)
 - Patrol read (and CC) causing OS boot failure on media error correction(DCSG00080809 (Port Of Defect DCSG00098159)
 - pl: backend PCIe: 'pl pci devlnk' is missing from the 'pl dbg' dump(DCSG00052268 (Port Of Defect DCSG00052348)
 - Expose enclosure controller property is being reset at every boot(DCSG00244065 (Port Of Defect DCSG00246029)
 - NVMe devices VPD page 83 NAA descriptor may conflict with EUI64 ID reported(DCSG00148775 (Port Of Defect DCSG00153702)
 - Ventura; Add code to prevent downgrade from phase 14 to previous phases for winbond(DCSG00059594 (Port Of Defect DCSG00061399)
 - Aero: pl: SATA device may not link up following a link down(DCSG00054906 (Port Of Defect DCSG00073959)
 - Controller crash and resets on attempt to boot to windows OS(DCSG00099330 (Port Of Defect DCSG00258053)
 - [9440-8i + MR7.14 + ARM] Controller hit Fatal error when doing drives hard reset test by storelibtest(DCSG00312453 (Port Of Defect DCSG00318217)
 - Auto Cfg Parameters Changed is not generated when host led management is changed.(DCSG00118646 (Port Of Defect DCSG00220598)
 - PL: Blind retries by MegaRAID FW when PL is in out of resource condition results in IOs to MS-SES exhausting retries(DCSG00033753 (Port Of Defect DCSG00046628)
 - DHSP to GHSP is generating duplicate alerts(DCSG00081077 (Port Of Defect DCSG00084765)
 - NVMe Identify Controller sent over OOB fails with MFI_STAT_INVALID_CMD(DCSG00165400 (Port Of Defect DCSG00219970)
 - Event is generated even though LDBBM table is not updated(DCSG00259244 (Port Of Defect DCSG00293136)
 - [MR3508+MR7.14 +X86 ] Controller is seen with Fatal error by unknown reason unexpectedly (XH628 V5's 3508 mem.c issue)(DCSG00312708 (Port Of Defect DCSG00316966)
 - Bad Phy events are generated for UBM slots with element status = NO_ACCESS_ALLOWED(DCSG00336611 (Port Of Defect DCSG00342269)
 - Rebooting from the OS hangs at a blank screen and does not report the Shutdown AEN(DCSG00258074 (Port Of Defect DCSG00278410)
 - Assertion failure in fw\ddf\ddfPd.c seen during foreign import(DCSG00272547 (Port Of Defect DCSG00297147)
 - For an OEM, Install of RHEL 8.0 using NVME PD R0 fails. It will error out during the creation of the UEFI partition(DCSG00077835 (Port Of Defect DCSG00099954)
 - SATA only : Controller hang is observed due to recursive function call.(DCSG00139294 (Port Of Defect DCSG00226371)
 - pl: NVMe: unexpected NVMe init failure if LBA 0 is inaccessible(DCSG00120588 (Port Of Defect DCSG00121315)
 - CurrentControllerMode Value is Showing "null" instead Of "RAID"(DCSG00149932 (Port Of Defect DCSG00216977)
 - [9440-8i+MR7.12/7.13/7.14Beta2+ARM] controller FW printed Assertion failure in fw\cpu\arm\exceptions.c at line 1006: 0 during fio issue verify(2F) commands to sas hdd(JBOD)(DCSG00236990 (Port Of Defect DCSG00244898)
 - PL SATA: Sanitize operation is completed before actual completion from drive.(DCSG00119155 (Port Of Defect DCSG00126831)
 - Preboot uitlity HII shows enable host led management button when feature is not available.(DCSG00229197 (Port Of Defect DCSG00246024)
 - pl: NVMe: Select field used during NVMe init without verifying support(DCSG00050182 (Port Of Defect DCSG00051206)
 - Aero A0: External cards do not support PCIe and SRIS by default(DCSG00131571 (Port Of Defect DCSG00143420)
 - Incorrect slot mapping on UBM backplane with additional DFCs support(DCSG00077969 (Port Of Defect DCSG00082256)
 - [9440-8i + MR7.14 ARM/X86] Auto config RAID0 in HII didnot work as expected(DCSG00297592 (Port Of Defect DCSG00302395)
 - Not able to enable JBOD property in Ventura controllers(DCSG00069029 (Port Of Defect DCSG00077146)
 - Complete config missing boot message shown for NON-RLM case(DCSG00091414 (Port Of Defect DCSG00105196)
 - Invalidate slot not working for IT SPDM(DCSG00131485 (Port Of Defect DCSG00139744)
 - OEM: OOB SLT returns error 0x7004 when run SelfCheckingDiagnostic option(DCSG00352769 (Port Of Defect DCSG00362761)
 - The personality behavior=None is allowed to be set.(DCSG00079271 (Port Of Defect DCSG00165536)
 - Unsupported drive LED Solid Green on Rear Backplane - LED flashing green expected(DCSG00130055 (Port Of Defect DCSG00216979)
 - MR controller resets(DCSG00119480 (Port Of Defect DCSG00220841)
 - Drive Discovery failed with Port Hot-swap on Aero16e controller(DCSG00042446 (Port Of Defect DCSG00052013)
 - [Aero/Ventura] Bootloader corruption with firmware download and DC cycle in loop.(DCSG00238233 (Port Of Defect DCSG00245453)
 - CTRL_MFC_DEFAULTS_SET DCMD returning error when PERC in eHBA mode(DCSG00227153 (Port Of Defect DCSG00237600)
 - COL Failure on AC cycle(DCSG00132764 (Port Of Defect DCSG00167574)
 - ExtManPage41 TX Values are not being applied / run by AERO SERDES(DCSG00311524 (Port Of Defect DCSG00315525)
 - autoconfig field is not set to None when firmware is upgraded to current programme package(DCSG00113492 (Port Of Defect DCSG00143274)
 - Allowed Cfg Options does not show support for SINGLE_PD_R0 option(DCSG00083472 (Port Of Defect DCSG00084767)
 - [9440-8i+X86+MR7.13] SSD JBOD Drive state will change from (U-Up) to (D-Down/PowerSave) when they rmmod and insmod megaraid(DCSG00265980 (Port Of Defect DCSG00322200)
 - extend timeout for OOB command for SATA EPC enabled drive(DCSG00335204 (Port Of Defect DCSG00350449)
 - Last LDBBM entry in the list is not cleared after VD Deletion(DCSG00255330 (Port Of Defect DCSG00297028)
 - StorCLI shows success in Converting Foreign drive as JBOD.(DCSG00261213 (Port Of Defect DCSG00277787)
 - VSES page 02h reports incorrect status for linkup failed array device element on certain UBM slots(DCSG00112320 (Port Of Defect DCSG00127720)
 - Ventura B0: Device discovery fails on 9400-16e(DCSG00045385 (Port Of Defect DCSG00045779)
 - Aero config import from file fails with EPD-JBOD drives(DCSG00096587 (Port Of Defect DCSG00107691)
 - PL : 0x7008 fault seen when booting the bad clocked controller connected to Atlas(DCSG00114774 (Port Of Defect DCSG00121424)
 - Expander attached devices not reported to host if enclosure slot ordering is enabled in event replay.(DCSG00108094 (Port Of Defect DCSG00111584)
 - Fix unnecessarily generated fatal event in status process for unlock PD(DCSG00378774 (Port Of Defect DCSG00395841)
 - PL: 2 Atlases in single MPT mode with 2 host ports each will have drives on one switch not mapped to that Atlas's SES Page 0Ah(DCSG00054949 (Port Of Defect DCSG00062379)
 - Upto 90% performance drop with expander attached configuration.(DCSG00153860 (Port Of Defect DCSG00215210)
 - PL: PCIe switch discovery can cause processor exception when setting enclosure information(DCSG00063530 (Port Of Defect DCSG00063552)
 - PL backend PCIe: PL fault 0xD308 is observed with Aero and Atlas connected in bad clock environment(DCSG00134207 (Port Of Defect DCSG00137697)
 - Cisco - CSCvu90346 - SAS Controller Asserts if SubOEMID that is not in NVDATA is selected(DCSG00309776 (Port Of Defect DCSG00349160)
 - Aero: backend PCIe: link failure following link down(DCSG00043821 (Port Of Defect DCSG00048732)
 - Secured EPD IO Error = media is write protected after continuous PushPull within 2 seconds(DCSG00081483 (Port Of Defect DCSG00218465)
 - FW faults during driver unload and load process(DCSG00107743 (Port Of Defect DCSG00228865)
 - Dev-defect: Reset SES Mgmt flags after the reboot (not in the same boot) when personality changed to RAID.(DCSG00118666 (Port Of Defect DCSG00122763)
 - Incorrect Man page 7 Phy-Slot mapping set for 9500-xx channel HBAs(DCSG00061349 (Port Of Defect DCSG00062359)
 - [Aero] Change the Manpage 7 Phy to Connector settings and Disable NVMe support in ManPage9(DCSG00031186 (Port Of Defect DCSG00044352)
 - logGet: Found invalid event at e82858c4 pe 1411(DCSG00040960 (Port Of Defect DCSG00082112)
 - [9361-8i MR6.14] storcli return with error when set patrolread mode(DCSG00072635 (Port Of Defect DCSG00075239)
 - [SPDM IT] Return actual size of certificate chain content to SPDM LIB(DCSG00233805 (Port Of Defect DCSG00245634)
 - PL SATA only : SATA init timeout observed due to drive taking longer to respond to sanitize status ext(DCSG00225935 (Port Of Defect DCSG00227376)
 - IOC Exceptions not getting cleared after flashing the BIOS image with correct ROP version(DCSG00226395 (Port Of Defect DCSG00227987)
 - EKM many key request events generated when creating secured VDs with multiple disks(DCSG00141624 (Port Of Defect DCSG00216974)
 - NVmeAdmin: Assertion failure in fw\raid\nvmePRP.c seen when NVMe PT response size is >=12k(DCSG00223413 (Port Of Defect DCSG00242570)
 - AXI access errors causing FW asserts or faults due to invalid SATA passthrough commands(DCSG00215338 (Port Of Defect DCSG00243095)
 - (SATA Only) SCSI ATA Passthrough command with data transfer fails.(DCSG00120976 (Port Of Defect DCSG00121420)
 - storcli show success for PDCache setting change on VD even though Cache setting of drive was not changed(DCSG00319375 (Port Of Defect DCSG00349021)
 - NVMe Init Error List has drive entry missing when multiple Bad PDs are inserted(DCSG00113697 (Port Of Defect DCSG00121316)
 - Current version of Back plane firmware does not display correct after update, Pathfinder(DCSG00239284 (Port Of Defect DCSG00245055)
 - Fix code for proper use of patrol-read active and msgActive flags(DCSG00079695 (Port Of Defect DCSG00082129)
 - SAS9341-8i board encounters 'Previous configuration completely missing at boot' error(DCSG00067176 (Port Of Defect DCSG00075326)
 - Toolbox clean command sent to clean flash fails.(DCSG00059302 (Port Of Defect DCSG00062455)
 - Utility not providing an VD task to encrypt a VD (post creation)(DCSG00101763 (Port Of Defect DCSG00105200)
 - Target ID of EPD drives is not equal to Slot ID when drives are connected(DCSG00167860 (Port Of Defect DCSG00240678)
 - Dev-Defect - PRP-List overwritten in Double-Buffer-Copy-To-Host for response size > 8K(DCSG00258471 (Port Of Defect DCSG00269098)
 - Aero_scrutinycli: "Device -c" command output is not matching with the firmware cli parameter values in Aero behind atlas configuration.(DCSG00121852 (Port Of Defect DCSG00127910)
 - FW is overriding the data length , present in the command frame header, with sizeof (MR_LD_ALLOWED_OPS_EXT)(DCSG00322186 (Port Of Defect DCSG00342267)
 - 9440-8i System black screen and hang during S4 + CC stress(DCSG00297794 (Port Of Defect DCSG00311470)
 - tty battery FRU sometime corrupt when reading from cli(DCSG00222664 (Port Of Defect DCSG00230726)
 - NVMe Init Error: Device with no namespaces shows 'Namespace count Invalid' as Unrecoverable Error(DCSG00290593 (Port Of Defect DCSG00303511)
 - Moving Controller From Single VSES config to a multi-VSES config causes issues in windows OS.(DCSG00071784 (Port Of Defect DCSG00080399)
 - PL NVMe : PCI task management is not getting completed.(DCSG00231422 (Port Of Defect DCSG00266052)
 - PL: 9460-16i incorrect slot numbers assigned attaching to OEM specific mixed mode backplane(DCSG00243953 (Port Of Defect DCSG00340147)
 - NVMe repair command fails with 'No drive support for recovery' loginfo(DCSG00129498 (Port Of Defect DCSG00137668)
 - supportEPDWithAutoConfigOff supported bit is set as 1(DCSG00239272 (Port Of Defect DCSG00242941)
 - StorCLI shows success in Converting Foreign drive as JBOD.(DCSG00261213 (Port Of Defect DCSG00299706)
 - MR FW not responding to resume within 3 seconds(DCSG00243834 (Port Of Defect DCSG00304052)
 - Expander_FW : Expander FW upgrade or downgrade through CIMC is not getting reflected on host applications(DCSG00171248 (Port Of Defect DCSG00232623)
 - [Aero] Fault 0xA03 observed when updating FW with a bad NVMe drive in the topology(DCSG00132639 (Port Of Defect DCSG00136250)
 - scattered file changes to include some debug prints and also minor change to debug print(DCSG00057124 (Port Of Defect DCSG00057818)
 - SPDM IT:SPDM BMC bring up on P2 server(DCSG00238540 (Port Of Defect DCSG00241397)
 - Aero: PL with newer Atlas FW (4.2) has extra slot number in the Atlas enclosure(DCSG00284238 (Port Of Defect DCSG00291431)
 - Cisco: Found "C0: Dumping poll data. total length = 3, objtype 0", these message coming to uart firmware log continuously after update BMC(DCSG00349880 (Port Of Defect DCSG00419731)
 - VSES - SES page not set correctly for Front adapters(DCSG00084525 (Port Of Defect DCSG00093718)
 - NvmeAdmin: 'Exception handler called' observed while converting drive to Non RAID preceded by Export Log from OM(DCSG00224879 (Port Of Defect DCSG00242573)

EnhancementRequests:
 - SCONS: Update signing call to utilize new digest argument(DCSG00365964)
 - PL: Support Managed Switch (Atlas) slot range VSEC command for its single MPT mode(DCSG00071626)
 - Snapdump performance improvements(DCSG00066931)
 - Address the issue found during code review - flush write verify issues on MR7(DCSG00011893)
 - Populate currentSpeed for SAS Phys(DCSG00072397)
 - SEA IT TRNG HW enable(DCSG00098752)
 - Make PLDM (Type 2) specific changes as per Smart Storage System Design Specification RevisionV 1.64(DCSG00039603)
 - Modify generate HBICList script(DCSG00105230)
 - Health Data Events - Create counters for various Health Data Events(DCSG00078912)
 - No Longer Close Flash for Error Cases(DCSG00061091)
 - Ventura/Aero: Add Ext. Man Page 48 to store CoreDump options(DCSG00026309)
 - Add output to RMC log to indicate image is for debug use(DCSG00080714)
 - Add Aero/Sea Info to Ventura Summary Release Notes(DCSG00077941)
 - Aero3: SecureBoot BIOS Image Download with new Key is failing(DCSG00233694)
 - Snapdump doesn't log recon ld info(DCSG00132717)
 - Platform related configuration changes updation(DCSG00039844)
 - Enable SAS 240K R5 RW on MR7.15(DCSG00241136)
 - OOB diagnostic Test Improvments(DCSG00051246)
 - Support for config reset protocol(DCSG00062958)
 - SPDM: Implementation: Implement CDI generation and ECDSA Key Pair generation(DCSG00060737)
 - Aero+Cub Multi-path improvements(DCSG00063755)
 - Update HWBIC Generation XMLs for CQ9(DCSG00100142)
 - SPDMLIB: OEM requested to not report Get Measurement Capable(DCSG00323053)
 - SCONS: Add IOP_SUBSYSTEM_ enums to assembly(DCSG00341313)
 - Release Automation: Submit auto-BST jobs(DCSG00091315)
 - Update secureSign build process to sign executables with Broadcom windows authenticode signing key(DCSG00381469)
 - Ctrl - H support for pkg - secure Image flash validation(DCSG00137059)
 - Persisting secureLD targetId bitmap(DCSG00237413)
 - Resolving the compilation conflicts while integrating the library with FW(DCSG00045448)
 - Certificate read and Write wrapper functions & Slot management(DCSG00105005)
 - Automate Build Job and Release Job Submission Process(DCSG00045139)
 - Remove A0 raw fw rawA0.fw file from release scripts(DCSG00211914)
 - MPI changes to configure backend ASPM(DCSG00051277)
 - Megamon commands enabled for testing mbedtls library(DCSG00036604)
 - Avenger support for the LIBSPDM(DCSG00081168)
 - pl: SATA: vendor specific ATA Standby handling(DCSG00074400)
 - On 9440-8i controllers, do not update timeout value for a DCDB issued by host on JBOD(DCSG00128903)
 - Update WWID in the PCIe interface structure for PCIe switches(DCSG00152603)
 - Aero/Ventura: Enable easier debug when SPI FLASH is bad(DCSG00058537)
 - Log SPDM events entries in log page 0(DCSG00139949)
 - PL: NVMe Drive Repair(DCSG00055563)
 -(DCSG00395629)
 - Implement a secure version of memset for SPDM code to use to zero out buffer(DCSG00208365)
 - Automate version update stage in release process(DCSG00122144)
 - SPDM LIB: Implement version scheme(DCSG00072483)
 - Implemented newUBMBackplane type support.(DCSG00049601)
 - PL logic to create VSES instances per Backplane number(DCSG00069245)
 - Enable NS management and Format commands in the PT path(DCSG00129551)
 - Cisco sg_sanitize PT support(DCSG00232659)
 - SPDM_LIBRARY: Change for SPDM Policy Implementation(DCSG00097417)
 - [Aero][Ventura] Sign windows build applications and avoid antivirus from deleting them.(DCSG00025757)
 - Allow General Processing Failure from Atlas on unsupported commands to not result in 0xEA20 fault(DCSG00170698)
 - Added SPDM lib to IT FW code base and handle MCTP VDM SPDM commands(DCSG00063688)
 - SSD Wear gauge per Smart Storage Design Specification 1.64(DCSG00028105)
 - SPDM: Test the Library Integration. UT framework in MR Megamon(DCSG00037855)
 - BST - Reset(DCSG00335443)
 - Add preboot environment variables to snapdump logs.(DCSG00139621)
 - MBEDTLS LIB: Enhancement to source of randomness for generating key pair(DCSG00148786)
 - Shenandoah COL BST Script(DCSG00355898)
 - [Aero] [SPDM] Support Export Certificate Signing Request command(DCSG00063692)
 - SPDM:7.15: Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust(DCSG00216859)
 - Add optional arg '-hash_algorithm' that will accept -sha256 or -sha512 but if that arg is not provided then it will default to -sha512(DCSG00353453)
 - Ventura/Aero: Update SPI flash test to print better failure information(DCSG00070917)
 - Remove cdi get for Avenger(DCSG00152679)
 - Atlas drives connected to an OEM controller behind Atlas PCI switch SMART polling 10s interval(DCSG00051225)
 - PL: Coordinate reset on Atlas FW update to limit IO disruption to NVMe drives behind Atlas(DCSG00097342)
 - Multi-Chemistry BMU support(DCSG00018257)
 - MbedTLS: Explicitly make enumerator value of enum type to 4-byte value(DCSG00054557)
 - MBEDTLS LIB: Rename sha256.h header file to avoid conflict with MR FW sha256.h header file(DCSG00068675)
 - Enable 24 PCIe device support for Aero External boards.(DCSG00278073)
 - Add support for TCG Enterprise SED drives that require Packet.SessionNumber to be zero for Open, Close, Config, Sync(DCSG00060670)
 - Preboot Trace Buffer [PTB] for Ventura/Aero - MR Firmware(DCSG00054971)
 - Aero: Add support for SPDM ExtManPage 52(DCSG00108545)
 - SPDM: Implementation: Implement Subject Name validation for CSR (Certfificate Signing Request) and CSR generation(DCSG00069168)
 - Release Automation: Validate FW Header post Package Creation(DCSG00055071)
 - CFGI Integration for MR(DCSG00077966)
 - Displaying "Volume" instead of "Logical Drive" or "LD" in events and boot messages.(DCSG00029102)
 - Release Automation: create Aero IT FW only Release Order Package(DCSG00066845)
 - SPDM LIB: Implement SPDM Get Measurement command(DCSG00234758)
 - pl: backend PCIe: PCIe Hinting(DCSG00050640)
 - Disable hardware debug ports(DCSG00143569)
 - SPDM: Coding: Implement SPDM Commands (SPDM Lib Shell & Client of SPDM Lib)(DCSG00039443
 - RDE - Implement support for dynamic PDR repository change in Managed Device Firmware(DCSG00167169)
 - Add framework to inject correctable errors to endpoint in Atlas dev bst(DCSG00306577)
 - Aero/Ventura: Add CLI to test QE bit modification(DCSG00148653)
 - Shenandoah - Implement PLDM RDE Platform Firmware(DCSG00068974)
 - pl: NVMe: handle Namespace Not Ready error during NVMe init(DCSG00071652)
 - MbedTLS Lib: disable file system related functions & enable memory allocation and prints functions to be compiled in CPP environment(DCSG00060384)
 - CDI & Key Generation source integration with IT FW(DCSG00063690)
 - SPDM: 7.15: Enhancement to source of randomness for generating key pair(DCSG00148777)
 - Revert 145.1 Changes(DCSG00431043)
 - Update PLI Spec(DCSG00008045)
 - Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR firmware(DCSG00227036)
 - pl: backend PCIe: examine BAR attributes following endpoint/switch reset(DCSG00060688)
 - SECUREBOOT_LIB: Move hardware touch (ApSha HASH & HMAC and OTP eFuse Read) from MR SPDM code to Secure Boot Lib(DCSG00082166)
 - Update Sea Channel XMLs to PCI Device ID 0xE6(DCSG00079238)
 - Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - nvram(DCSG00228248)
 - Coverity Upgrade Aero Build to latest version(DCSG00103023)
 - Populate connector name from sas device page 0.(DCSG00051271)
 - SPDM:7.15: Export CSR & Import Cert Open & Close Session(DCSG00167484)
 - SPDM: Implement a secure version of memset for SPDM code to use to zero out buffer(DCSG00126569)
 - Implement to change i2c messages to etty(DCSG00065857)
 - NVMe Drive Init failure Error Reporting(DCSG00055566)
 - MBEDTLS LIB: Change large local variable memory allocation from the stack to dynamic memory allocation from the heap(DCSG00087564)
 - Vendor requested megamon command to simulate bad flash to be supported all its boards(DCSG00313349)
 - Aero/Ventura: Move DMCore hardware file to common(DCSG00007511)
 - Add Avenger support for libmbed tls.(DCSG00051695)
 - SPDM: Implementation: Rename sha256.h header file to avoid conflict with MR FW sha256.h header file(DCSG00068681)
 - After purge operation, Blocking OOB traffic.(DCSG00071207)
 - pl: NVMe: handle Namespace Not Ready error during NVMe init (part 2)(DCSG00075871)
 - Resolving the compilation conflicts while integrating the library with FW(DCSG00045470)
 - [Aero][SPDM] IOP framework to support CFGI Reads and Writes(DCSG00076512)
 - SPDM: Implement Security Page Wrapper for reading/writing key page(DCSG00096299)
 - Allow full binTrc ETTY collection for on-demand snapdumps(DCSG00061636)
 - Add NVMe drive init failure condition tracking list(DCSG00077909)
 - [SPDM]SBlib upgrade to 2.02(DCSG00091314)
 - Provide Configurability For SPDM Library(DCSG00045604)
 - MBEDTLS LIB: Implementation: Use CDI to generate ECDSA key pair(DCSG00067411)
 - 7.14 MR: Change for SPDM Policy Implementation(DCSG00098359)
 - Remove protection of NVDATA pages for channel(DCSG00079568)
 - Support getting the defaults and supported properties in Auto Config NONE mode(DCSG00215321)
 - Support snapdump for 216-x controllers(DCSG00151384)
 - Do not update timeout value for a DCDB issued by host on JBOD.(DCSG00058148)
 - SPDM_LIB: Support to build Challenge buffer with multiple GET_CERTIFICATE/CERTIFICATE_RESPONSE(DCSG00225175)
 - Populate UBM backplane fields as part of EFI_HP_ADAPTER_INFO_SMART_CARRIER_BACKPLANE_DATA(DCSG00062513)
 - Update Version descriptors for standard inquiry data of SATA and vSES devices(DCSG00037325)
 - Avenger OOB: PLDM Header Generation Tool(DCSG00132673)
 - [Aero SPDM] XSD changes to support SPDM version in a new manufacturing page(DCSG00103227)
 - Update NVMe to SCSI Error code translation.(DCSG00098339)
 - Added "pl serdes tx" and "pl serdes rx" command(DCSG00053828)
 - FW should reflect PD cache setting changes on EPD(DCSG00050115)
 - Support for NVMe Firmware Download when the image size exceeds the SNTL Transfer limitation.(DCSG00053656)
 - Disk labels need to be tied to fixed physical ports in order(DCSG00097307)
 - SPDM: Enable SPDM LIB support by default & improve the check for buffer size of ECDSA signature buffer which contains integer R and S in der format(DCSG00051715)
 - Shrink MbedTLS library size(DCSG00059001)
 - MBEDTLS LIB: Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust(DCSG00216867)
 - Add pkeyopt argument and support for checking for zero length input file and fail with appropriate error(DCSG00348441)
 - Add autoconfig debug prints to snapdump(DCSG00134888)
 - Update Windows CNG Key Gen and Signing operations to use SHA1 of CA Cert value from new CQ field(DCSG00369036)
 - Reverting branding changes(DCSG00061954)
 - ISE completion status to support UEFI Sanitize protocol(DCSG00062524)
 - Fix Mbedtls build scripts to accommodate Aero and Avenger(DCSG00150272)
 - MR SPDM:7.15: Implement client APIs for SPDM Get Measurement command (in SPDM LIB)(DCSG00234724)
 - Export of UBM backplane type to the platform(DCSG00046485)
 - Add support for U.2 UBM backplane(DCSG00118415)
 - Correcting the print function configuration(DCSG00047741)
 - Populate connector name from PCIe device page 0.(DCSG00057131)
 - Add milliseconds to etty print timestamps(DCSG00066928)
 - XSD and NVDATA changes to support SPDM manufacturing and Security pages(DCSG00063680)
 - LKM compliance to Cryptographic Algorithm Requirements v1.5(DCSG00330429)
 - SPDM: Coding: MR FW MCTP Handler ( SPDM Request & Response)(DCSG00039439)
 - Reduce rebuild delay for SSDs(DCSG00056703)
 - SECUREBOOT_LIB: Move SRK and CCR eFuse register access functions to SBLIB(DCSG00086765)
 - Package Stamping Verification(DCSG00096506)
 - Release Automation: Integrate utility for deliver/rebase into release scripts.(DCSG00094677)
 - SPDM: Move hardware touch (ApSha HASH & HMAC and OTP eFuse Read) from MR SPDM code to Secure Boot Lib(DCSG00082170)
 - Revert the algorithm which determine if offload is sustainable(DCSG00079183)
 - Config file changes to including prints(DCSG00047716)
 - pl: backend PCIe: add debug print for a discovery failure case(DCSG00083082)
 - Shenandoah - Add Snapdump support for PLDM Type-2 and Type-6 platform modules(DCSG00226289)
 - NVMe Drive Repair command processing(DCSG00054950)
 - Release Automation: updates for rebase operation(DCSG00134475)
 - Adding Events Handling for NVMe Drive Init Error reporting/Repair(DCSG00055427)
 - MbedTLS lib integration with IT FW(DCSG00063687)
 - MBEDTLS: Implementation: Implement Subject Name validation for CSR (Certfificate Signing Request) and CSR generation(DCSG00069942)
 - Release Automation: Integration of all script modules(DCSG00120937)
 - SPDM: Implement Cert HMAC, Cert Key, Key HMAC, KEK, Nonce, AES decryption/encryption of key storage(DCSG00075028)
 - Security page 0 and page 1 - Wrapper(DCSG00092779)
 - Coordinate Atlas FW update to prevent unnecessary RAID volume cleanup due to devices spontaneously being removed while IO is active(DCSG00097340)
 - Support for the Smart Array MR216i-p/a Gen 10+ Controller(DCSG00041392)
 - Providing Link and Device Related Counters(DCSG00056834)
 - Aero 7.15: Enhancement for Exttty buffer on OOB debug print(DCSG00134972)
 - Implement secureSignLinuxDrv CLI tool for HSM managed keys with support for certTypes PKCS7|X509 using NFKM engine(DCSG00396377)
 - Aero3: Harden Managed Switch SES (Atlas) SES Page 0Ah translation with error injection framework(DCSG00037053)
 - Enhance Atlas Dev BST core framework(DCSG00350412)
 - Release Automation: Automate state transitions for ReleaseOrder(DCSG00035457)
 - ComboSerdes: add functionality for bypass ready waiting(DCSG00167482)
 - Aero SPDM Sblib change: provide sblib interface to disable specified HW debug port.(DCSG00166877)
 - Update NVDATA to display appropriate controller names and to remove invalid connectors(DCSG00068959)
 - Atlas DevBST: Add synthetic DPC verification test cases(DCSG00335033)
 - MBEDTLS LIB: Implement version scheme(DCSG00072481)
 - SPDM: Add messages to etty buffer as part of snapdump for SPDM(DCSG00123020)
 - Aero: Change XMEMCOPY default to disabled in Aero(DCSG00082841)
 - Cache bypass tuning on Aero(DCSG00051793)
 - SPDM library: Adding PLDM print module style.(DCSG00060323)
 - Support UBM diag tools in Scrutiny CLI for MR(DCSG00097311)
 - PLDM FW UPDT component classification updated(DCSG00060855)
 - Improve RMC debug image indicator(DCSG00093342)
 - PL UBM support UBM for PCIe SW upstream port config(DCSG00120726)
 - NVMe Drive Init failure Error Reporting.(DCSG00054970)
 - Implementation of changes as per new Energy Pack State transitions(DCSG00034018)
 - RDE - Display complete drive revision and model number strings in REST client(DCSG00105101)
 - Dev Unit Test : AER on Host Port and Downstream port is exposed(DCSG00355354)
 - MISC changes for NVMe drive repair(DCSG00086663)
 - 7.15 SPDM: HW debug port disable and megamon utility limited access.(DCSG00148680)
 - SPDM: Add support for new bit CTRL INFO and new MFI status in MR API(DCSG00106381)
 - Implemented UBM box bay number support(DCSG00042528)
 - Add SasSerdesCtl0_7 registers to pl serdes(DCSG00069982)
 - SPDM Client Code Change: Adding PLDM print module style(DCSG00060325)
 - Support DEVICE_KEY_BASIS flags.(DCSG00342838)
 - pl: NVMe: update Block Limits VPD page translation(DCSG00055387)
 - Add support for C++/CPP compile for libspdm(DCSG00051200)
 - [Aero IT SPDM] Attestation policy at the boot-up time.(DCSG00063691)
 - SPDM: Remove hard-coded certificate chain and keypair(DCSG00126415)
 - NVRAM Aero SPDM Policy: Add Nvram flag to enable/disable SPDM feature in megamon(DCSG00112317)
 - Multi-path/Multi-port message filtering(DCSG00063756)
 - Adding critical events to a bad SAS/SATA drive that is consistently failing TM Reset(DCSG00298872 (Port Of EnhancementRequest DCSG00350451)
 - CIO deprecated IOtype display while recon Vd - to be removed(DCSG00301684 (Port Of EnhancementRequest DCSG00317150)
 - Extending SnapDump Persistence(DCSG00247000 (Port Of EnhancementRequest DCSG00266146)
 - Secure drive Crypto erase behavior change(DCSG00057696 (Port Of EnhancementRequest DCSG00129708)
 - Disk labels need to be tied to fixed physical ports in order(DCSG00240927 (Port Of EnhancementRequest DCSG00266089)
 - Initialize and persist SES management related flags when personality change from HBA to RAID(DCSG00112013 (Port Of EnhancementRequest DCSG00117802)
 - Enhancement to source of randomness for generating key pair(DCSG00208477 (Port Of EnhancementRequest DCSG00250093)
 - Monitoring Drive Performance and Predictive Failure feature to be removed for certain OEM(DCSG00082984 (Port Of EnhancementRequest DCSG00099031)
 - Support bit for "cannotExecuteOnce" autoconfig parameter needs to be set as 0 for all configure modes(DCSG00183076 (Port Of EnhancementRequest DCSG00230641)
 - This ER is to allow exposing of active internal expander based backplane to host for jbod LED management.(DCSG00109563 (Port Of EnhancementRequest DCSG00111427)
 - Treat PD missing for RLM only as critical(DCSG00056769 (Port Of EnhancementRequest DCSG00077311)
 - Change to the Powerloss Recovery Sequence to Recover Corrupted BMU Flash(DCSG00235822 (Port Of EnhancementRequest DCSG00242968)
 - MR FW changes to use Smart Polling Intervals values from NVDATA.(PR#DCSG00113187)(DCSG00211992 (Port Of EnhancementRequest DCSG00237772)
 - Change to BMU update process for power loss recovery(DCSG00072757 (Port Of EnhancementRequest DCSG00082107)
 - Aero SAS Performance Enhancement on AMD Rome as part of PR(DCSG00064583 (Port Of EnhancementRequest DCSG00065934)
 - SPDM IT: Add memory allocation/free for SPDM_LIB(DCSG00229260 (Port Of EnhancementRequest DCSG00241396)
 - Modify Ventura Build scripts to add a new Signed image with different AVSO Setting in FW RO(DCSG00231216 (Port Of EnhancementRequest DCSG00231535)
 - Restore Factory Default doesn't prompt user to reboot the system after being performed(DCSG00120440 (Port Of EnhancementRequest DCSG00122770)
 - DA-SEP internal backplanes host led management status not correct(DCSG00176030 (Port Of EnhancementRequest DCSG00223407)
 - Enable DST in NVMe Cmd Filtering(DCSG00076595 (Port Of EnhancementRequest DCSG00077206)
 - Add new security events(DCSG00167311 (Port Of EnhancementRequest DCSG00223401)
 - Aero Secure Boot: Add Key Update Pending Check for 'COMPLETE' Image Download(DCSG00241566 (Port Of EnhancementRequest DCSG00250024)
 - Advertise certain Secure Boot Properties using a config page for Application to be able to display it(DCSG00078835 (Port Of EnhancementRequest DCSG00093843)
 -(DCSG00057696 (Port Of EnhancementRequest DCSG00099028)
 - Execute once Auto configure option needs to be allowed for EPD-PT behaviour mode for certain controllers.(DCSG00216966 (Port Of EnhancementRequest DCSG00301658)
 - Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR firmware(DCSG00227036 (Port Of EnhancementRequest DCSG00255160)
 - Need a mechanism to get supported device protocols for each controller form factor(DCSG00108508 (Port Of EnhancementRequest DCSG00117796)
 - Add boot mode print to log during boot(DCSG00169640 (Port Of EnhancementRequest DCSG00223405)
 - Host access to internal backplane SEPs(DCSG00212119 (Port Of EnhancementRequest DCSG00223410)
 - Increase timeout value for Revert Tper commands to support drives from new drive vendor(DCSG00068257 (Port Of EnhancementRequest DCSG00077204)
 - Allow FW to reprovision UBAD drives(DCSG00054917 (Port Of EnhancementRequest DCSG00077287)
 - Snap-dump Enhancement - remove unnecessary duplicate prints(DCSG00312222 (Port Of EnhancementRequest DCSG00318525)
 - FW should treat copyback start as import success in case of secured drives.(DCSG00054919 (Port Of EnhancementRequest DCSG00077288)
 - In pre boot environment, if IO's received greater than 1MB reject the command with correct error status and not to Assert(DCSG00056745 (Port Of EnhancementRequest DCSG00078538)
 - Monitoring Drive Performance and Predictive Failure feature to be removed for certain OEM(DCSG00082984 (Port Of EnhancementRequest DCSG00322062)
 - In pre boot environment, if IO's received greater than 1MB reject the command with correct error status and not to Assert(DCSG00056745 (Port Of EnhancementRequest DCSG00077207)
 - Unblock the ability to secure EPDs via SEKM(DCSG00098356 (Port Of EnhancementRequest DCSG00105206)
 - EnhancementRequest DCSG00062819: SPDM: Implementation: DCMD Commands addition for Export/Import CSR(DCSG00062819 (Port Of EnhancementRequest DCSG00083491)
 - Include new field Auto Config Parameter structure to indicate that AutoConfig R0 property cannot be set .(DCSG00073908 (Port Of EnhancementRequest DCSG00077308)
 - Remove informational prints from tty log(DCSG00014871 (Port Of EnhancementRequest DCSG00072334)
 - MR FW feature to dump battery FRU data(DCSG00115404 (Port Of EnhancementRequest DCSG00117805)


Version 51.13.0-3624 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:7.13.00.0
	UEFI Driver:0x070D0301
	HII: 07.13.06.06
	MR FW: 5.130.00-3318
    package 51.13.0-3624
	
MR7.13
Defects:
-Atlas Behind Aero BST is not working as the correct XML file is not copied..(DCSG00322761)
-Secure SED and SES Management ctrl properties are toggling after changing autoconfig from None to JBOD and vice versa..(DCSG00243819)
-Target ID of EPD drives is not equal to Slot ID when drives are connected.(DCSG00167860)
-Some of the JBODs are not included under "PR excluded VD" , while performing storcli /cx show pr when all the drives are converted to JBOD..(DCSG00126731)
-9440-8i System black screen and hang during S4 + CC stress.(DCSG00297794)
-Firmware Flash in loop:Assertion failure in fw\mros\mem.c at line 839 observed while flashing firmware in loop with OOB traffic.(DCSG00312138)
-[NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive.(DCSG00136092)
-9440-8i+X86+MR7.13] SSD JBOD Drive state will change from (U-Up) to (D-Down/PowerSave) when they rmmod and insmod megaraid.(DCSG00265980)
-StorCLI shows success in Converting Foreign drive as JBOD..(DCSG00261213)
-API clarification for large io support.(DCSG00307042)
-NVDATA XSD in MR is out of sync from the latest spec.(DCSG00234826)
-Fix error handling in traceTool.py.(DCSG00181406)
-9460-8i faults repeatedly at fw\raid\utils.c.(DCSG00265811)
-VSES: Incorrect linkup failed elements status reported on certain slots of the UBM backplane.(DCSG00113486)
-MR FW fails MR_DCMD_CTRL_MFC_DEFAULTS_SET DCMD..(DCSG00316343)
-StorCLI shows "PR excluded VDs" where actually PR is running on online PDs of VD..(DCSG00126725)
-supportEPDWithAutoConfigOff supported bit is set as 1.(DCSG00239272 (Port Of Defect DCSG00242939))
-[9460-8i+MR7.12 Patch+X86] Use script to upgrade OEM-made SAS SSD firmware underneath 9460-8i (7.9, 7.11, and 7.12) will fail.(DCSG00124592 (Port Of Defect DCSG00240576))
-[9440-8i + MR7.14 ARM/X86] Auto config RAID0 in HII didnot work as expected.(DCSG00297592 (Port Of Defect DCSG00302394)
-JBOD drive is converted to Configured Drive after OCR / Reboot.(DCSG00293760 (Port Of Defect DCSG00311206))
-FW faults during driver unload and load process.(DCSG00107743 (Port Of Defect DCSG00134484))
-UNMAP support blocked for an OEM.(DCSG00253426 (Port Of Defect DCSG00257228))
-Expander_FW: Expander FW upgrade or downgrade through OEM test tool is not getting reflected on host applications.(DCSG00171248 (Port Of Defect DCSG00228308))
-Low risk temporary solution for preventing duplicate target Ids.(DCSG00243849 (Port Of Defect DCSG00249463))
-[Aero/Ventura] Allow the backplane detection state machine to retry the FRU detection..(DCSG00219908 (Port Of Defect DCSG00222975))
-In JBOD profile, set VD Write Cache to AWB shows success even though WB Supported is set to NO.(DCSG00113956 (Port Of Defect DCSG00240940))
-A8: Aero MR 7.14: Intermittent issue: Assertion failure in fw\raid\taskman.c at line 361 , when tried to start IO's on SAS SSD 24 expander connect RAID5 RW.(DCSG00139362 (Port Of Defect DCSG00226055))
-FW faults during driver unload and load process.(DCSG00107743 (Port Of Defect DCSG00228870))
-Dynamically allocating Ghost Target ID for Recon - Min Changes.(DCSG00248269 (Port Of Defect DCSG00255781))
-MR 7.15: Invalid Arguments error seen while setting config file w.r.t JBODs from Storcli..(DCSG00221279 (Port Of Defect DCSG00313427))
-storcli hang intermittently during ocr on i2c based oob platform.(DCSG00171506 (Port Of Defect DCSG00222663))
-[9440-8i+MR7.12/7.13/7.14Beta2+ARM] Controller FW printed Assertion failure in fw\cpu\arm\exceptions.c at line 1006: 0 during fio issue verify(2F) commands.(DCSG00236990 (Port Of Defect DCSG00244897))
-After loading aero driver, the VD of the controller cannot be listed.(DCSG00297806 (Port Of Defect DCSG00309392))
-As part of the Device Add\Removal Event, the enclosure handle passed on by the PL FW to the upper layer is incorrect..(DCSG00298128 (Port Of Defect DCSG00299606))
-After loading aero driver, the VD of the controller cannot be listed.(DCSG00297806 (Port Of Defect DCSG00311838))
-Last LDBBM entry in the list is not cleared after VD Deletion.(DCSG00255330 (Port Of Defect DCSG00257907))
-[9440-8i + MR7.14 + ARM] Controller hit Fatal error when doing drives hard reset test by storelibtest.(DCSG00312453 (Port Of Defect DCSG00318215))
-Expander FW fail to flash FW sometimes in offline mode.(DCSG00217264 (Port Of Defect DCSG00232782))
-[MR3508+MR7.14 +X86 ] Controller is seen with Fatal error by unknown reason unexpectedly (XH628 V5's 3508 mem.c issue).(DCSG00312708 (Port Of Defect DCSG00316968))
-UNMAP support blocked on an OEM.(DCSG00253426 (Port Of Defect DCSG00257808))
-FW fault seen during server bootup..(DCSG00345176 (Port Of Defect DCSG00350214))

EnhancementRequests:
-API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI STAT.(DCSG00222915)
-MegaAPI: Add API Controller Properties and MFCD for ParityReadCacheBypass (PR: DCSG00237022).(DCSG00282676)
-XSD changes Disk labels need to be tied to fixed physical ports in order.(DCSG00141730)
-Implement customSign.exe CLI wrapper utility to help customers sign with their private key.(DCSG00234646)
-Added drive push pull tests.(DCSG00253665)
-XSD : Add New field 'singlePortMultipathFeatures' in MPI2_MR_PARAMS_PAGE_0.(DCSG00310657)
-MR PVT API :Update mr_configpage.h file for New fields 'predFailPollDAInterval' and 'predFailPollInterval' in MPI2_MR_PARAMS_PAGE.(DCSG00223408)
-DCSG00265812.
-XSD: Add New field 'parityReadCacheBypass' in MPI2_MR_PARAMS_PAGE_0 for PR DCSG00237022.(DCSG00282675)
-SMART Polling Improvement - API Changes.(DCSG00246317)
-To add return status MFI_STAT_OK_REBOOT_REQUIRED to MR_DCMD_LD_SET_PROPERTIES in mr.h.(DCSG00256271)
-Additional FDE type for Ruby SED support.(DCSG00055878)
-MFI SMP Port Num API changes.(DCSG00257777)
-BST script modification due to change in RO content.(DCSG00265215)
-Set disablePdDegradedMedia in all XSDs.(DCSG00324772)
-MR PVT API :Update mr_configpage.h file for Ruby SED support.(DCSG00278424)
-DCSG00315850
-Check in XSD for new security page ExtManPage 49/50/51, Security Page 0/1.(DCSG00082978)
-XSD :Add New fields 'predFailPollDAInterval' and 'predFailPollInterval' in MPI2_MR_PARAMS_PAGE_0.(DCSG00218900)
-Disable custom image build for HBA BST.(DCSG00301780)
-Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API.(DCSG00226286)
-XSD : Need a mechanism to get supported device protocols for each controller form factor.(DCSG00108534)
-SMART Polling Improvement- API Changes.(DCSG00214352)
-Add noembed support to signtools.(DCSG00314237)
-Add Atlas Behind Aero Setup in Atlas AutoBST.(DCSG00253672)
-MR API: reclassify MR_EVT_CTRL_FW_VALID_SNAPDUMP_AVAILABLE as informational.(DCSG00292323)
-DCSG00306898
-Atlas BST:- USD integration.(DCSG00234348)
-SPDM python script: Add handling to manage actual certificate certain for Aero with depth=4.(DCSG00315798)
-PvtAPI: Add new field 'parityReadCacheBypass' in MPI2_MR_PARAMS_PAGE_0 for PR DCSG00237022.(DCSG00284472)
-NVDATA change for Ruby SED support.(DCSG00278286)
-New MFI Stat for the updated recon behavior.(DCSG00229416)
-Added power cycle tests in Atlas AutoBST.(DCSG00234319)
-Make updating the embedded key( step 1) of securesign optional.(DCSG00313996)
-XSD change adding SPDM new page ExtManPage 52 for SPDM Version.(DCSG00108514)
-MR PVT API: Add singlePortMultipathFeatures to MPI2_MR_PARAMS_PAGE_0.(DCSG00272230)
-Make necessary changes to atlas_bst in valscripts to enable BST for Nvidia stream.(DCSG00237302)
-BST setup with Channel HBA + Elrond.(DCSG00234391)
-Aero: Integrate SBLIB 2.03.03 into phase 14 mr.(DCSG00299615)
-MR7 API: Add package incompatibility reporting.(DCSG00231443)
-Support bit for "cannotExecuteOnce" autoconfig parameter needs to be set as 0 for all configure modes.(DCSG00183076 (Port Of EnhancementRequest DCSG00230640))
-Monitoring Drive Performance and Predictive Failure feature to be removed for certain OEM.(DCSG00082984 (Port Of EnhancementRequest DCSG00099030)
-Populate currentSpeed for SAS Phys.(DCSG00072397 (Port Of EnhancementRequest DCSG00312144)
-Need a mechanism to get supported device protocols for each controller form factor.(DCSG00108508 (Port Of EnhancementRequest DCSG00117794)
-Snap-dump Enhancement - remove unnecessary duplicate prints.(DCSG00312222 (Port Of EnhancementRequest DCSG00318522))	

	

Version 51.13.0-3427 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:7.13.00.0
	UEFI Driver:0x070D0301
	HII: 07.13.06.05
	MR FW: 5.130.00-3181
    package 51.13.0-3427
	
MR7.13
Defects:
-Aero Alpha: FW hit assertion failure in fw\hw\debug\binTrc.c at line 1910: !((ext->remove.step > 0) && (ext->add.step > 0)) while OCR during long weekend.(DCSG00042025)
-A lot of unexplained prints about PD Fail history seen in during FW boot.(DCSG00052904)
-Implicitly converting an expression to a narrower type.(DCSG00061066)
-Resolve rebase conflict.(DCSG00020839)
-MR 7.13 after set autoconfig jbod and securesed off found pd always on for both "sed enabled" and "secured" feature.(DCSG00063197)
-VSES SES Page 02h reports Unknown (06h) Element Status for some Array device elements in a wide DFC slot.(DCSG00069091)
-Ventura B0: Device discovery fails on 9400-16e.(DCSG00045385)
-On Linux: Unable to write SAS address update record to persistent region of the flash via sg_write_buffer.(DCSG00060769)
-MR_7.13_Aero_Beta: After Quick Boot - Un-configured good SSD SATA drives moved to spindown state ..(DCSG00074318)
-Fix Static Analysis reported issue 47110 47108 in Aero Project. They are VisionFirmwareDownload defects.(DCSG00054850)
-Increase the number of Fast Training Sequences requested by Aero. (PL).(DCSG00031501)
-Diagnostic test command memory allocation failure is not handled gracefully.(DCSG00055451)
-Fix Static Analysis reported issue 46685 46283 46274 46111 in Aero Project.(DCSG00054852)
-Ventura B0: 4 enclosures are created for 2 vSES in multi-UBM config in x8 mode.(DCSG00035111)
-AeroMR: Win/Lin, Gen3, 4/8DC, 16EC, NVMe, 1/4/16W, RAID5, RW/OLTP, 4K/8k/16K/32K, QD=64/256, 8-40% Regression from RO3010 to ROP3102..(DCSG00083355)
-pl: backend PCIe: debug prints.(DCSG00013387)
-Updating the slot number with Phy order on the board.(DCSG00072285)
-AeroMR GEN3 WIN,8 and 16 Drive SAS HDD, RAID0/RAID5/RAID6, 4K/8K RW, All QD..(DCSG00021481)
iMR BST VDs are getting created with read ahead property set.(DCSG00103807)
-pl: backend PCIe: switch rediscovery fails with certain switch configurations.(DCSG00061635)
-Fix Static Analysis reported issue 47315 in Aero Project.(DCSG00054554)
-Implicitly converting an expression to a narrower type.(DCSG00053674)
-BIOS private data being overwritten at init time when EPD and RAID VD are both used..(DCSG00066476)
-PL: Remove the using of an LMID frame as a request or reply frame to an MPI Device.(DCSG00040943)
-Implicitly converting an expression to a narrower type.(DCSG00055790)
-Atlas behind Aero IT: Fault code: 0x4000EDAC while running IOs and TMs.(DCSG00022533)
-Disable DPM for IMR.(DCSG00035833)
-Implicitly converting an expression to a narrower type.(DCSG00055415)
-PLDM FW UPDT component classification needs to be changed for MR ROP.(DCSG00050349)
-Ventura B0: PCIe support disabled with UBM and Capella II switch in the topology.(DCSG00039024)
-PL: Over 250+ power cycles of managed switch (Atlas) causes an associated SES to be inaccessible.(DCSG00048699)
-SPILIB: New Version of Winbond SPI flash times out on write.(DCSG00054923)
-Fix Static Analysis reported issue #46173 in Aero Project.(DCSG00054386)
-MR7.13 Alpha: SLT menu "(5) GetEnclosures List" always list slot numbers from 0.(DCSG00071882)
-Implicitly converting an expression to a narrower type.(DCSG00055917)
-pl: NVMe: CFS not checked during handling of Abort Task.(DCSG00023749)
-Implicitly converting an expression to a narrower type.(DCSG00056067)
-Ventura B0: ISTWI Error observed during controller cable management initialization.(DCSG00041605)
-Aero A0: Controller fault EC57 observed on doing individual lane break test on VendorX Gen4 NVMe drive.(DCSG00010317)
-FW crashed with Exception handler error at bios post while booting up with Multipath config.(DCSG00045474)
-HIIM component is not listed.(DCSG00015033)
-Update checking in Scons for multiple Coverity scans.(DCSG00068814)
-Aero: PL cannot handle very large SES Page 0Ah from Managed Switch SES for MPI SEP Request.(DCSG00010049)
-pl: backend PCIe: 265D fault after deferred max payload size configuration.(DCSG00036696)
-Aero A0: In Windows OS redundant disks detected when controller connected to Elrond Ex1.(DCSG00061406)
-Aero: backend PCIe: disallow DPC for PCIe 3 and earlier specific vendor switches.(DCSG00010608)
-BSOD when running CoreDump with Aero connected to Atlas switch.(DCSG00042497)
-NVDATA Major version should be 0E00 for Phase 14.(DCSG00022006)
-Backend PCIe link cfg may fail attaching to Ux2 UBM backplane.(DCSG00037821)
-9500 Channel board default I2C clock frequency higher than the spec specified.(DCSG00039829)
-7.13-Alpha Aero: Data Abort Exception on exiting Megamon at end of onDemand snapdumps capture via zcdump.(DCSG00066639)
-Kill Adapter when Running RAID 5 RMW CTIO 4K Random Writes.(DCSG00074348)
-Avenger IOP: When CBB replies to NVSRAM Init PMU message, it returns FALSE.(DCSG00017760)
-Application cannot find the CoreDump region size needed to erase the region.(DCSG00028503)
-Implicitly converting an expression to a narrower type.(DCSG00054062)
-MR 7.13 PA1: OS hangs while formatting VDs.(DCSG00038731)
-MR 7.13 Beta: Aero reports: Assertion failure heavy IO+Reconstruction+TM Reset.(DCSG00076663)
-PL: 2 Atlases in single MPT mode with 2 host ports each will have drives on one switch not mapped to that Atlas's SES Page 0Ah.(DCSG00054949)
-Updated the forceUpdate format in PLDM header generation Tool.(DCSG00106563)
-DMA test result status need to be corrected for OOB runs.(DCSG00048879)
-Fix misspelling in print statement.(DCSG00059689)
-Battery Learn schedule is not being reset to 90 days after a new battery chemID is installed..(DCSG00012617)
-MR FW Assertion failure in snapdump module.(DCSG00120091)
-Updating FW (on 9400 series HBA) from Ph-7 to Ph-14 causes "invalid flash" message on FW bootup.(DCSG00167100)
-PLDM FW UPDT component classification needs to be changed for MR ROP.(DCSG00048634)
-OEM DCMD error when executed SelfDiag test from OOB in I2C mode.(DCSG00056313)
-Aero: Error on posting a SCSI IO request to Atlas SES can cause IO forever being pended.(DCSG00012605)
-Aero: backend PCIe: 265D fault if PCIe Device Page 2 is read for a SES device.(DCSG00016069)
-Windows powershell shows 48 slots in single VSES mode.(DCSG00022999)
-Toolbox clean command sent to clean flash fails.(DCSG00059302)
-Updated GoldenX to handle the CoreDump Region.(DCSG00042890)
-COL source code fixes in response to static analysis tool analysis.(DCSG00055398)
-offload was not sustainable.(DCSG00054867)
-"iop show diag" output collection in CoreDump causes controller to hang.(DCSG00027941)
-Change boot loader version to 32 bit field.(DCSG00053711)
-pl: backend PCIe: Atlas switch may not be discovered.(DCSG00036613)
-Dev Defect to Fix Some Code Maintenance Issues.(DCSG00057795)
-Aero: backend PCIe: link failure after PCIe IO Unit Page 1 link disable.(DCSG00050164)
-locate LEDs state fails for odd slots on Ex2 backplane.(DCSG00078806)
-MR-7.13: Observing FW generated Snap dump with 0 bytes & no mention of Tigger time..(DCSG00072162)
-Remove the 'NVCache device failed" message when there is no supercap.(DCSG00058905)
-Use NVRAM to save PTB information -- API changes.(DCSG00082981)
-pl: NVMe: maximum blocksize should be limited to 2 MB.(DCSG00022705)
-Do not create multiple EPDs if the command comes from a user request.(DCSG00035753)
-Implicitly converting and expression to a narrower type.(DCSG00055385)
-Coverity usability.(DCSG00066267)
-PL: Controller not functional when booting up with 2 Ex1 UBMs in x8 mode.(DCSG00038959)
--Aero 7.13 PA1: Ondemand Snapdump does not capture PL Logs.(DCSG00042060)
-Ventura_FW : Invalid slot id 255 shown for the PD in the PD Events when powercycle during reconstruction.(DCSG00036947)
-Aero3: In XMEMCOPY==0 mode writes to config pages get overwritten on next reset.(DCSG00038206)
-FW faults during driver unload and load process.(DCSG00107743)
-PL: Back-to-back retries by IOP/Host when PL is in out of resource condition results in IOs to MS-SES exhausting retries.(DCSG00033753)
-"iop show cfg all" command captured by core-dump is zero.(DCSG00047928)
-[Aero][PLDM] FW version reported wrongly to BMC( Board Management Controller) over out of band.(DCSG00050201)
-pl: NVMe: Write Buffer parameters should be validated against FWUG.(DCSG00027855)
-MR7.13 Beta: Improve Config creation time to yield other traffic..(DCSG00078563)
-VSES page 02h reports incorrect status for linkup failed array device element on certain UBM slots.(DCSG00112320)
-Aero: Various faults occur with PCIe clock configuration mismatch between Aero and managed switch (Atlas).(DCSG00012378)
-Fix Static Analysis reported issue of data type implicit conversion..(DCSG00054562)
-UBM Auto HFC grouping fixes and debug print fixes.(DCSG00012363)
-PL Discovery debug prints for Expander Phys/Encl slot enumeration.(DCSG00039850)
-UBM: Incorrect slot number enumerated for a DFC on 3 x4 DFCs UBM config.(DCSG00048027)
-PL: PCIe switch discovery can cause processor exception when setting enclosure information.(DCSG00063530)
-pl: backend PCIe: legacy interrupt may not be serviced if interrupt mask fails.(DCSG00010071)
-iMR Ventura: R0 PD becomes UGUnsp instead of Online after system reboot.(DCSG00048692)
-smart recovery start pointer issue.(DCSG00053709)
-Number of initiators gets decremented to 0xFF.(DCSG00051990)
-7.13 BST Failure: Data Abort During First Restore of COL BST.(DCSG00043549)
-pl: NVMe: controller reset shouldn't be issued if EN or RDY are 0.(DCSG00024038)
-Fix supercap/battery code so it process monitoring out of 2nd cpu core.(DCSG00044316)
-Fix Static Analysis reported issue #46175 in Aero Project.(DCSG00053406)
-PCIe OOB maxpacketsize value wrongly displayed from storcli application.(DCSG00057268)
-Aero: pl: SATA device may not link up following a link down.(DCSG00054906)
-Zuma Beach: FW - Diagnostics failed for PD event observed when Drive Pull & Push operation is performed.(DCSG00068142)
-Coredump text files don't have file extensions.(DCSG00043119)
-Aero A0: Write and DC issues on NVMe drives running data integrity with XMEMCOPY==0 (new boot mode).(DCSG00034356)
-NVMe devices VPD page 83 NAA descriptor may conflict with EUI64 ID reported.(DCSG00060347)
-bst_jbod fails to change personality for iMR controller.(DCSG00105299)
-Coverity detected unreachable code in IOP MCTP code.(DCSG00010189)
-SPILIB2: If the default clock divider is specified, there are excessive clock prints.(DCSG00013239)
-PL: TM Device Reset to NVMe drive under out of LMID condition can cause Data Abort Exception to the processor
Description Of.(DCSG00036763)
-PH14 Windows Driver: on 2016,19H2 OS,Getting BSOD for fault command.(DCSG00048607)
-Superfluous message for NVME IO with SGL.(DCSG00017353)
-Fix Static Analysis reported issue #46155 #46132 #46115 in Aero Project.(DCSG00054162)
-dmdiag Aladin MegaMon commands not working.(DCSG00074881)
-Aero 7.13 PA1: Kill Adapter Snapdump does not capture Frame and other IO information.(DCSG00045441)
-Use NVRAM to save PTB information.(DCSG00081231)
-Ventura; Add code to prevent downgrade from phase 14 to previous phases for winbond.(DCSG00059594)
-Fault 4322 Observed On Sea 8i Board.(DCSG00028298)
-Aero_DBU_7.13_Alpha: On Demand Snapdump during IO SATA and SAS SSD result to driver issued KA.(DCSG00060967)
-Fix ring buffer decoder's slowness with decoding a trace buffer.(DCSG00050675)
-Back out changes of ER DCSG00029633 that limits VSES devices to 2.(DCSG00053379)
-Copy paste and overflow errors in cache offload module.(DCSG00068812)
-Change 2WIRE_RESET and PERST GPIO signals logic level in NVDATA settings.(DCSG00025523)
-pl: NVMe: incorrect sense key is returned for Access Denied NVMe status.(DCSG00063924)
-Implicitly converting an expression to a narrower type.(DCSG00054081)
-Aero/Ventura: Fault 0xD203 - Trace Buffer Manager not in Extended mode when processing diagnostic requests.(DCSG00033003)
-Patrol Read fails to run on all the online drives when iteration count > 1 and pr maxconcurrentpds < online-drive-count.(DCSG00048576)
-Fix Static Analysis reported issue 47293 47290 47283 in Aero Project.(DCSG00054556)
-Allow secure PDs to be configured as Enhanced Physical Drive after PD is unlocked.(DCSG00053641)
-cannot flash FW even after a warm reboot when followed by OOB FW flashing is interrupted.(DCSG00079022)
-FW exception when get snapdump is initiated.(DCSG00069689)
-storcli hang intermittently during ocr on i2c based oob platform.(DCSG00171506)
-Allow PCIe IO Unit page 1 link rate debug override option to override BP reported max link rate.(DCSG00042965)
-FW - AMD2P Wave1 - UG bad drive is missing in MR 7.12 FW.(DCSG00026516)
-iMR hits exception after FW upgrade before OCR then do storcli /c0 get snapdump.(DCSG00060816)
-Fix Static Analysis reported issue #46081 in Aero Project.(DCSG00054389)
-Remove erroneous successful event if no foreign configuration is deleted at storcli command.(DCSG00043589)
-SPILIB 2.0: Custom Parts Write Parameters are Incorrect.(DCSG00018735)
-MR_7.13-DBU: Windows Driver: During Hibernation PL Fault 0000d213 is seen.(DCSG00063631)
-Correct SPDM python script StepsToRun.txt, remove redundant bmc.tar.bz2 file..(DCSG00150282)
-SPILIB: The SPI2 release zip contains SPI1 headers.(DCSG00019887)
-Quotes present in NVDATA XMLs.(DCSG00045528)
-Added Discovery Notify when controller boot up or reset..(DCSG00048725)
-PL: Remove all MPI 2.6 PCIe event handling and unexpected SAS events from managed switch's MPI Device.(DCSG00040937)
-Fix Static Analysis reported issue 46759 in Aero Project.(DCSG00054851)
-Lot of SES related prints in the FW log.(DCSG00047720)
-move ETTY code from binTrc.c to extTTY.c.(DCSG00052207)
-Increase EstimatedTimeBeforeSendingRequestFirmwareData to 10 mins.(DCSG00026292)
-PL: Firmware is incorrectly acking spinup requests twice in a row.(DCSG00031070)
-Printing vd_id for jbods in iMR raises script error..(DCSG00115555)
-[Aero] Change the Manpage 7 Phy to Connector settings and Disable NVMe support in ManPage9.(DCSG00031186)
-SPILIB 2.0: Initialization fails for Spansion 64MB part in serial mode.(DCSG00061011)
-pl: backend PCIe: endpoint or switch is unexpectedly reset in a couple of error cases.(DCSG00030361)
-Fix Static Analysis reported issue 47268, 46980 46977 i in Aero Project. They are PD and LD variable defects.(DCSG00054560)
-Fix Static Analysis reported issue 46716 in Aero Project.(DCSG00054864)
-coverity defect - non critical defects.(DCSG00044331)
-MR_7.13_Aero_Alpha: SSD SATA SysPD's retain in spin-down state after quickboot and after VMFS file system creation..(DCSG00060912)
-Fix Static Analysis reported issue 47281 47276 in Aero Project.(DCSG00054558)
-Invalid cache line caused exception.(DCSG00058690)
-SPILIB2: Windbond 16MB device fails to program.(DCSG00017381)
-PL: NVMe: Remove MPI26_EVENT_PCIDEV_STAT_RC_SANITIZE_OPERATION_COMPLETED Temporary Event.(DCSG00031848)
-Increase the time wait time when quad mode bit gets written for write operation to complete..(DCSG00061711)
-[Aero] Upload request for the flash regions like CoreDump/Config1/Config2/SBR/CBB fails with LogInfo code:.(DCSG00034467)
-Aero: backend PCIe: link failure following link down.(DCSG00043821)
-SPILIB 2.0: Cypress 256Mbit SPI Flash Is Not Supported.(DCSG00121768)
-Ventura: The host PCIe link width may be narrower than expected.(DCSG00078678)
-Deleting file system during bst is not done using mrcli.(DCSG00103799)
-HW Workaround:Resizable BARs capability.(DCSG00014562)
-Firmware asserts during customer specific UBM Backplane enumeration..(DCSG00058770)
-pl: Ventura/Mercator: device side PCIe link failure following adapter reset.(DCSG00024652)
-Aero: Firmware Download should return success with loginfo indicating POR is necessary.(DCSG00055371)
-Aero MR7.13-PA2: PL Fault 0000d213 (Assertion failure in fw\dm\pl3.5\pliopi.c at line 1269) when running driver.(DCSG00045063)
-Data Exception abort happening when function called to dump memory blocks.(DCSG00063139)
-pl: NVMe: Drive Firmware update fails on mode 0xE.(DCSG00044028)
-SPI controller hang.(DCSG00057863)
-SPILIB: Winbond 256MBit maximum page write time increased from rev "A" to rev "B" of their specification.(DCSG00170747)
-Controller boot does not proceed after DISM.(DCSG00043038)
-MR FW failed to arm offload when cache offload was expected to start.(DCSG00065467)
-Add sense dump to the MPT Error dump.(DCSG00068343)
-Need PL MPI Device data dumps in "pl dbg" for debug, i.e. "pl mpidev dbg".(DCSG00037838)
-[Ventura] SAS/SATA direct attached drive is not listed when VSES disabled in nvata..(DCSG00033019)
-pl: backend PCIe: 'pl pci devlnk' is missing from the 'pl dbg' dump.(DCSG00052268)
-ExtTTYWrite will Infinite Loop if buff only Contains '\n\0'.(DCSG00043070)
-PL: Initial MPI driver error injection can cause the Managed Switch's SES to not be exposed to OS.(DCSG00045593)
-Aero: HW_SETTINGS_CHANGE PCIe PHY LF setting should be changed from 16 to 15.(DCSG00012481)
-PL: Device removal event is not sent for hot removed end device.(DCSG00023448)
-pl: NVMe: limit resource frame usage by NVMe IO breakup.(DCSG00039263)
-Bug in SerDes M0 Code U16RegDataFindReplace().(DCSG00043881)
-Aero A0: Atlas switch (SRIS mode) not discovered with Elrond Ex1 config.(DCSG00036996)
-pl: port enable timeout when PCIe and backplane detection are disabled.(DCSG00035201)
-Aero: During FW download we should not overwrite status when POR is necessary.(DCSG00062988)
-MR_7.13 OEM :Assertion failure in fw\hw\pbam\serial.c at line 1614 observed while Create/delete Vd's with 4K.(DCSG00057140)
-After executing "coredumo -erase" from ScrutinyCLI, flash offsets are not reset.(DCSG00037801)
-pl: backend PCIe: incorrect value written to Device Status/Control register during error handling.(DCSG00038289)
-NVDATA in wrong location in MR release zip files.(DCSG00009013)
-Incorrect Man page 7 Phy-Slot mapping set for 9500-xx channel HBAs.(DCSG00061349)
-Aero config import from file fails with EPD-JBOD drives.(DCSG00096587)
-Unable to detect drives behind Sea controller during Windows installation.(DCSG00012569)
-MR_7.13 PA2 DBU : Multiple VM's power on/shutdown on NVM-E result to Exception Handler Called for Processor.(DCSG00052153)
-MR7.13: FW hit "C0:Assertion failure in fw\ddf\ddfConfig.c at line 2403: 0" while doing cablepull/push to trigger.(DCSG00035771
-pl: NVMe: Select field used during NVMe init without verifying support.(DCSG00050182)
-Ventura MR 7.13 Alpha FW; Win/Lin -5.6% to 12% drop in SW, SR profile for IO Size-4K, 8K,16K, 32K QDs.(DCSG00067276)
-Removing minimum capacitance check from the supercap code.(DCSG00043746)
-Firmware faults while running a script to do drive push-pulls.(DCSG00082970)
-7.13-Alpha Aero: Capturing multiple snapdumps via Megamon zcdump hang.(DCSG00066510)
-Aero3: Uploading main firmware in XmemCopy=0 mode causes an abort.(DCSG00035015)
-Fix static analysis issues.(DCSG00087283)
-scattered file changes to include some debug prints and also minor change to debug print.(DCSG00057124)
-WG: In presence of foreign configuration, DHSP's assigned to simple config DG's are not displayed.(DCSG00072257)
-For an OEM, Install of RHEL 8.0 using NVME PD R0 fails. It will error out during the creation of the UEFI partition.(DCSG00077835 (Port Of Defect DCSG00099953)
-Coverity Bugs in PL Enclosure Management Files.(DCSG00043514 (Port Of Defect DCSG00045037)
-Incorrect slot mapping on UBM backplane with additional DFCs support.(DCSG00077969 (Port Of Defect DCSG00098289)
-Patrol read (and CC) causing OS boot failure on media error correction.(DCSG00080809 (Port Of Defect DCSG00098158))
-Drive Discovery failed with Port Hot-swap on Aero16e controller.(DCSG00042446 (Port Of Defect DCSG00052012)
-PL: Fault 0xD033 During Drive Pull Testing.(DCSG00027593 (Port Of Defect DCSG00027904))
-pl: NVMe: unexpected task management halt may occur.(DCSG00014455 (Port Of Defect DCSG00020914))
-(SATA Only) SCSI ATA Passthrough command with set feature command to set the drive in standby_y state.(DCSG00080256 (Port Of Defect DCSG00125866)
-Backplane detection never completes leading to discovery timeout..(DCSG00023081 (Port Of Defect DCSG00027622)
-The last known successful learn time is reported as in Nov 11, 2000.(DCSG00107714 (Port Of Defect DCSG00109132))
-StorCLI shows "PR excluded VDs" where actually PR is running on online PDs of VD.(DCSG00126725 (Port Of Defect DCSG00136360)
-pl: NVMe: fix a couple of debug issues related to unique identifiers.(DCSG00014628 (Port Of Defect DCSG00014917)
-Assertion failure in fw\dm\pl3.5\pliopi.c - During drive push pull and reboot.(DCSG00058474 (Port Of Defect DCSG00063863)
-PL : PL fault 0x7C41 is observed.(DCSG00030914 (Port Of Defect DCSG00032163))
-Automatic Copyback operation fails from Hotspare.(DCSG00048993 (Port Of Defect DCSG00052190)
-Not able to enable JBOD property in Ventura controllers.(DCSG00069029 (Port Of Defect DCSG00071231))
-PERC 10.5 - The personality behavior=None is allowed to be set and should be blocked in eHBA mode.(DCSG00062820 (Port Of Defect DCSG00063864)
-Fault 0x265d seen when the UBM FRU I2C read size configured to 2 bytes..(DCSG00026985 (Port Of Defect DCSG00031183)
-MCTP: SenseData not available for a failed command sent over OOB.(DCSG00054655 (Port Of Defect DCSG00057482))
-MR Ventura FW in JBOD mode still allows security erase by hdparm.(DCSG00104151 (Port Of Defect DCSG00119638))
-VSES may not report valid SES Page 0Ah elements for one of quads attached elements in a UBM backplane.(DCSG00013123 (Port Of Defect DCSG00013128)
-Direct attached PFA drive - LED is neither ON nor Blinking.(DCSG00111492 (Port Of Defect DCSG00143186)
-Controller Cache lost is seen while running 200-loop Cache Offload Test.(DCSG00038944 (Port Of Defect DCSG00043012)
-UBM Link Config may fail for HBA connector with Phys routed spans CSWs.(DCSG00022691 (Port Of Defect DCSG00023388))
-For an OEM - eHBA mode - FW stuck in reset loop when Recon target drive goes missing during OCR.(DCSG00072261 (Port Of Defect DCSG00082113))
-Cache Data Not recovered event not seen after 63 loops of cache offload with double dip.(DCSG00052343 (Port Of Defect DCSG00056778))
-Ventura B0: vSES goes missing after the first controller reset on UBM Ex1 in x8 HFC config.(DCSG00024555 (Port Of Defect DCSG00025784))
-Asserts from interrupt handlers are not working properly.(DCSG00127828 (Port Of Defect DCSG00137509)
-pl: discovery failure if PCIe backplane detection is disabled.(DCSG00013397 (Port Of Defect DCSG00014547)
-MR-7.13: FW - STP passthrough -FW sending ack before completely receiving all MCTP packets.(DCSG00078243 (Port Of Defect DCSG00096017))
-Aero A0: vSES is created even for managed Atlas (Ibanez) switch.(DCSG00012487 (Port Of Defect DCSG00015123)
-Aero: NVMe: device not removed if init fails and it then goes missing.(DCSG00013404 (Port Of Defect DCSG00019619)
-Snapdumps are discarded unnecessarily when flashing a new ROP.(DCSG00118659 (Port Of Defect DCSG00126333))
-Add debug code to enable debug fake flash error for OEM.(DCSG00024573 (Port Of Defect DCSG00041005))
-VSES - SES page not set correctly for Front adapters.(DCSG00084525 (Port Of Defect DCSG00093717))
-Unable to create a new security key (LKM) after deleting the security key.(DCSG00049508 (Port Of Defect DCSG00052192)
-Scrutiny GUI clear option fails to reset the PCIe error counters.(DCSG00014510 (Port Of Defect DCSG00015318)
-pl: backend PCIe: EC5B fault.(DCSG00022805 (Port Of Defect DCSG00024022))
-Some of the JBODs are not included under "PR excluded VD" , while performing storcli /cx show pr when all.(DCSG00126731 (Port Of Defect DCSG00150641))
-Elrond Ex2 w/ SAS/SATA incorrect slot numbers after PD move to different slot.(DCSG00069084 (Port Of Defect DCSG00143185)
-MR:Config Loss seen for rebooting server after Deleting Logical disk with OS on JBOD installed..(DCSG00058891 (Port Of Defect DCSG00068062))
-ED91 Fault while running IOs + OCR (controller reset) testing.(DCSG00057254 (Port Of Defect DCSG00066123))
-No Access Allowed' not set on VDs and UG drives when Host LED Mgmt on Non-RAID Disks is enabled.(DCSG00055795 (Port Of Defect DCSG00063842)
-Sea 16e PCIe TX Compliance Test Failure.(DCSG00052179 (Port Of Defect DCSG00082837)
-[Aero/Ventura] Unused phys are managed by VSes in SGPIO BP mode.(DCSG00151021 (Port Of Defect DCSG00216530)
-Increase EstimatedTimeBeforeSendingRequestFirmwareData to 10 mins.(DCSG00026292 (Port Of Defect DCSG00041001)
-pl: backend PCIe: 'pl pci dbgall' causes ring buffer spam.(DCSG00019925 (Port Of Defect DCSG00020114))
-SAS9341-8i board encounters 'Previous configuration completely missing at boot' error.(DCSG00067176 (Port Of Defect DCSG00125792)
-On Locating PD's,LED's are not blinking for drives connected to customer specific SGPIO Backplane..(DCSG00018823 (Port Of Defect DCSG00025496)
-0x6231 Fault during Sata Task Management.(DCSG00019315 (Port Of Defect DCSG00023449)
-[Aero]Remove NVMe support for SAS/SATA profile only.(DCSG00022886 (Port Of Defect DCSG00043411))
-pl: NVMe: E425 fault after vendor specific device firmware update.(DCSG00012593 (Port Of Defect DCSG00023687))
-Hard/SoftSecure Firmware unexpectedly flashes successfully on controllers.(DCSG00047664 (Port Of Defect DCSG00049000)
-MR 7.14 Beta: OCR did not complete appropriately and assert didn't print properly.(DCSG00212038 (Port Of Defect DCSG00212180))
-Aero-3: Serdes parameters from NVDATA are not sent to Serdes.(DCSG00022778 (Port Of Defect DCSG00026085)
-Multiple VSES created on SAS only 8-Slot UBM backplane with duplicate slot assignments.(DCSG00017373 (Port Of Defect DCSG00020913)
-Cryptographic Erase cannot be executed on drives that do support Format NVM but not Sanitize.(DCSG00071775 (Port Of Defect DCSG00072784)
-FW is stuck in an infinite reboot loop after uncorrectable ECC errors detected.(DCSG00056083 (Port Of Defect DCSG00059432))
-PL improperly cleaning up and recovering from hot resetting MPI Device (i.e. reinitializing MPI Device failing).(DCSG00032157 (Port Of Defect DCSG00032901))
-pl: backend PCIe: IO halt following temporary device removal.(DCSG00015943 (Port Of Defect DCSG00017372))
-Some of SAS/SATA drives attached to OEM Aero HBA may not be reported to host.(DCSG00076717 (Port Of Defect DCSG00080684))
-iMR FW may crash if disabled in device manager when Microsoft OS boots and lock up.(DCSG00040869 (Port Of Defect DCSG00122394))
-pl: firmware hang occurs in UBM command error case.(DCSG00072841 (Port Of Defect DCSG00072924))
-Expander FW fail to flash FW sometimes in offline mode.(DCSG00217264 (Port Of Defect DCSG00232946)
-pl: backend PCIe: prevent switch rediscovery quirks.(DCSG00018730 (Port Of Defect DCSG00046563))
-MR firmware does not parse PL CLI commands that are tagged as RESTRICTED correctly.(DCSG00051937 (Port Of Defect DCSG00056777))
-Locate PD fail on SGPIO enclosure when GroupId is disabled in Nvdata..(DCSG00034489 (Port Of Defect DCSG00044448)
-Aero: Powered cycled managed switch SES can become inaccessible.(DCSG00021412 (Port Of Defect DCSG00023096))
-MR-7.13: FW - STP passthrough response Firmware does not send some ending bytes..(DCSG00078207 (Port Of Defect DCSG00096019))
-UBM BP product revision version mismatch b/w SES Page 01 and SCSI Inquiry output.(DCSG00036978 (Port Of Defect DCSG00039453))
-iMR boot stuck in creating slot mapping.(DCSG00214223 (Port Of Defect DCSG00221598)
-PL 0x4E00 fault occurs when Task Management Device Resets are issued to different manged switch SESes at.(DCSG00032952 (Port Of Defect DCSG00037846))
-Updated the forceUpdate format in PLDM header generation Tool.(DCSG00106563 (Port Of Defect DCSG00107562))
-pl: Ventura/Mercator: device side PCIe link failure following adapter reset.(DCSG00038775 (Port Of Defect DCSG00039129))
-The personality behavior=JBOD is allowed to be set and should be blocked in eHBA mode.(DCSG00065411 (Port Of Defect DCSG00072315)
-CPLD Version is not shown with CLI show all command.(DCSG00039310 (Port Of Defect DCSG00043764))
-Perc 11: Undefined Instruction exception handler was called.(DCSG00058973 (Port Of Defect DCSG00063854))
-Controller fault 0x1902 is seen while issuing locate command to NVMe drives.(DCSG00062252 (Port Of Defect DCSG00066057))
-Debug message prints for controller that do not support NVMe..(DCSG00032425 (Port Of Defect DCSG00040999)
-0xD101 Fault observed running non-RW IOs to NVMe devices with drive push-pull.(DCSG00062701 (Port Of Defect DCSG00071042))
-Ventura B0: vSES not reported in Windows 2019 on certain UBM backplane config.(DCSG00026333 (Port Of Defect DCSG00026717))
-Dev Defect -Firmware asserted in ONFI module on OCR with Pinned cache..(DCSG00025534 (Port Of Defect DCSG00040925))
-BP and EPD LEDs are not exposed to the host if Slot 0 is configured as an EPD.(DCSG00026003 (Port Of Defect DCSG00063494))
-NVMe crypto erase sanitize command is issued in restricted completion mode.(DCSG00032146 (Port Of Defect DCSG00032573))
-Firmware version is blank and Macronix controller not being displayed in Raid manangement utilities.(DCSG00039322 (Port Of Defect DCSG00048996))
-Channel SAS3.5 HBAs cannot support published PD limits when loaded with SAS/SATA-only FW image.(DCSG00020917 (Port Of Defect DCSG00025802)
-Ventura B0: Incorrect VSES associated to unmanaged PCIe SW enclosure.(DCSG00023764 (Port Of Defect DCSG00024350))
-Cache data is lost after server power pull running IO on R5 and R6.(DCSG00027826 (Port Of Defect DCSG00034152))
-IOP: Trace buffer image has extra "CFG string.(DCSG00051124 (Port Of Defect DCSG00051218))

EnhancementRequests:
-Update summary release notes.(DCSG00008993)
-Ventura/Aero: Get debug file array sizes via a API variable for CFGI and PL.(DCSG00007512)
-Aero/Ventura: Integrate SPILIB 2.0 into IT firmware.(DCSG00010293)
-Single PLDM fw update file that covers all controllers from that series.(DCSG00019356)
-Change Aero default UART speed to 921600.(DCSG00026455)
-Reserve frames for backend PCIe activities.(DCSG00040462)
-MR API: NVME Drive Init Error Report and Repair for Aero/Ventura.(DCSG00071534)
-Ventura: Fix OEM Page7 Data.(DCSG00014014)
-MS-SES: Enabling translating devices in SES Page 0Ah from managed switch with non-unique BDFs.(DCSG00027432)
-Request for DPMstat support in MegaRAID SAS 3.5 controllers.(DCSG00020928)
-SPILIB: Modify Spilib 2.0 print settings to allow some prints in INFO.(DCSG00012641)
-New Event added when drive unique ID changes..(DCSG00036689)
-Define MR_SAS_PHY_CONNECTION.currentSpeed when no devices are connected.(DCSG00071066)
-FW SAS PVT API : A mechanism to get supported device protocols for each controller form factor.(DCSG00106306)
-Update IOP debug prints to replace %x with an appropriate modifier.(DCSG00015603)
-Update MR API mr_drv.h to modify field for RTTRace_header.(DCSG00042985)
-Aero: Update to SECUREBOOT Librrary 2.01.00.00.(DCSG00015120)
-Addition of atlas_bst scripts.(DCSG00218726)
-Check-in generate HBICList script.(DCSG00060758)
-Add new security events.(DCSG00167313)
-MR SBLIB: Update MR to handle SBLIB 2.01.00.00 change.(DCSG00036523)
-Aero: Unmap SPI areas that are virtually mapped to code areas.(DCSG00033552)
-pl: NVMe: RTD3 Entry Latency shutdown timing.(DCSG00014564)
-Enhance OEMs Dev BST scripts for driver upgrade and downgrade.(DCSG00152322)
-SPDM python script: Support to build Challenge buffer with multiple GET_CERTIFICATE/CERTIFICATE.(DCSG00226081)
-Allow host utils to manage CSWs individually in the presence of UBM.(DCSG00007471)
-Add new MR Event to notify user of PCIe hot reset fail.(DCSG00012583)
-pl: backend PCIe: allow override of backplane link config for debug.(DCSG00011555)
-PLDM: Integrate PLDM debug infrastructure with snapdump.(DCSG00027013)
-Determine UBM DFC drive type installed based on IFDET# and PRSNT# signals support implemented.(DCSG00029636)
-Modify package options for custom distribution of fir,ware binary.(DCSG00058202)
-API change to support 1. OEM specific UBM Back planes, and 2. Smart Battery state.(DCSG00040165)
-DCSG00030213
-Aero multi-party signing partial signing of images.(DCSG00048670)
-Aero: check in ACM-enabled partial file for Sea eval board.(DCSG00010543)
-For new CoreDump feature, set IOC-Capabilities "CoreDump" bit based on ManPage11 value only.(DCSG00031051)
-Add support for managed switch (Atlas) WWID in Vendor Specific Extended Capability.(DCSG00007993)
-Update GetEnclList/GetEnclListExt API behavior to support backplanes and SES devices where the device startslot is other than 0. - PR SCGCQ02198300.(DCSG00032147)
-Restrict In band /Out of band NVMe PT IO path to only Mgmt cmds.(DCSG00020978)
-Add Attention Button for drive removal support for traditional PCIe Hotplug in PCIe switches.(DCSG00017456)
-IOC FW need to capture Optical Cable's vendor serial number (vendor SN) so driver will be able to read it via MPI spec.(DCSG00023086)
-Defines and Implements debug routines.(DCSG00027043)
-Limit VSES device instances support to max 2.(DCSG00029633)
-pl: backend PCIe: enhance robustness of PCIe-related MPI event generation.(DCSG00009002)
-ESR Max Threshold check is not required for Aero.(DCSG00032992)
-Signing Linux executables via GPG method in HSM.(DCSG00077215)
-Aero SAS Performance Enhancement on AMD Rome as part of PR.(DCSG00064583)
-OEM Stream Merge to Channel stream.(DCSG00042561)
-MPI 2.6: Header file changes associated with Revision 2.6.9 of the specification.(DCSG00024640)
-NVMe Device PCIe Configuration Space Access DCMD.(DCSG00011488)
-Include new field cannotSetMode in MR_AUTO_CFG_PARAMETER structure.(DCSG00072780)
-Disable Active Cable Mgmt. IntL GPIO configuration from default NVDATA.(DCSG00014807)
-PLDM - Calculate PLDM package header checksum as per DSP0267_1.0.1 specification.(DCSG00048463)
-API changes to expose MR_AUTO_CFG_PARAMETER for NONE mode.(DCSG00151058)
-Optimizing LIBZ Make.(DCSG00035135)
-SPILIB 2.0: Add capability to support Winbond Parts with Factory Quad bit Disabled.(DCSG00140236)
-CM Utility to perform automated Deliver and Rebase actions.(DCSG00083856)
-Aero/Ventura IT: Optimize space by accessing non-IO path data directly from FLASH.(DCSG00025793)
-Add bitmap support to reduce command block time during 240 auto create R0 and avoid firmware reset.(DCSG00019322)
-SnapDump Enhancement : Enable Extended Trace Buffer by default in MR - implementation.(DCSG00020112)
-SPILIB 2.0: Add support for Block Protect bits configuration.(DCSG00170752)
-SPILIB2: Add support for Macronix MX25U25691G part.(DCSG00068680)
-API change OOB Self Diagnostics Design Improvements.(DCSG00054194)
-FW SAS MEGA API:Change MR_EVT_CTRL_FLASH_DISALLOWED_SB_KEY_CHANGE_PENDING event.(DCSG00086780)
-pl: update combo serdes library.(DCSG00011562)
-OEM ROMB design support.(DCSG00058083)
-Handle host PCIe BAR change event.(DCSG00017357)
-MR API changes - Support new Provisional bit in CTRL INFO and new MFI status for Platform Security.(DCSG00106380)
-Integrate MPI 2.6.10 headers into Ventura/Aero code.(DCSG00034259)
-updated BST script to run the 2TB+ drive tests in 90-100 minutes (previously would have taken hours).(DCSG00044714)
-UCM Action tool feature to support rebase using latest baseline.(DCSG00125616)
-Added CoreDump collection on IT-FW fault.(DCSG00023671)
-Create method to give verbose fault code descriptions.(DCSG00008046)
-Avenger IOP: Scons scripts update for firmware versioning.(DCSG00102973)
-MR: Single MPI support on Atlas.(DCSG00036693)
-Implement changes to secureSign signing tool and infrastructure to support mixed list of PublicKeys that.(DCSG00105430)
-Aero/Ventura: Add capability to return UNKNOWN status in SES, page 2, when link is down yet presence.(DCSG00015055)
-PL support for reporting UBM Backplane Number.(DCSG00031340)
-MR API: Change event class for SPDM events.(DCSG00134416)
-Update FW code to Disable SafeMode Boot on OCR using NVDATA..(DCSG00014521)
-Change all BBU messages to CacheVault for controllers using non-battery solution.(DCSG00022793)
-UpdateVersion tool to change and update version information in ClearCase.(DCSG00072590)
-DCSG00129388
-Add dev test suite directory and scripts.(DCSG00066934)
-Add support to build Avenger specific sbr image.(DCSG00101901)
-Add PERST# clamp to nvdata.(DCSG00010069)
-MR API changes - Support new DCMD for Platform Security SPDM.(DCSG00068355)
-Remove Obsolete Config Pages.(DCSG00020911)
-API changes needed for DPMstat support in MegaRAID SAS 3.5 controllers.(DCSG00023770)
-Aero/Ventura: Misc debug fixes and enhancements.(DCSG00009402)
-API changes for changing all BBU messages to CacheVault.(DCSG00038937)
-Scons build tool modification to append multi NVDATA binary.(DCSG00043318)
-Check in HwBoardImageConfig's partial xml files into Clear Case.(DCSG00061410)
-Tools to help analyze NVDATA ROP.(DCSG00055420)
-Add MR Register access to PDB0b, PDB1b and CCR Subset.(DCSG00042002)
-Aero/Ventura: Add auto-downgrade algorithm.(DCSG00010679)
-Modify board support package for custom boards.(DCSG00058089)
-SPILIB2: Eliminate address mask for Avenger Compatibility.(DCSG00013352)
-SPILIB(2): SPI Library based upon API 2.0.(DCSG00009014)
-pl: backend PCIe: check in some plugfest diag console code.(DCSG00012454)
-MPI 2.6: Add additional IOC_State (CoreDump) to allow firmware to dump debug logs without being reset.(DCSG00020567)
-Aero/Ventura IT: NVDATA Changes to enable FLASH execution mode.(DCSG00033543)
-Aero: Add permissions to access additional registers for Scrutiny.(DCSG00008197)
-Diagnostic command changes via OOB.(DCSG00013345)
-Updated personality change testing scripts to BST suite.(DCSG00171040)
-Ventura: Fix OEM DeviceSpecific fields.(DCSG00012208)
-Enhance OEMs Dev BST scripts.(DCSG00139069)
-API change to support ISE completion status.(DCSG00065881)
-pl: backend PCIe: add ring buffer printing of PL-initiated transaction data.(DCSG00018268)
-pl: backend PCIe: modify default PCIe device missing delay setting.(DCSG00018758)
-Aero: Add yet more ranges for scrutiny signal integrity.(DCSG00010274)
-Active State Power Management (ASPM) feature support for backend PCIe links.(DCSG00019848)
-Integrate MPI 2.6.9 headers into Ventura/Aero code.(DCSG00027926)
-Preboot Trace Buffer [PTB] for Ventura/Aero - MR API.(DCSG00060713)
-Support Vision FW signing.(DCSG00079737)
-Automate version update stage in release process.(DCSG00035455)
-Aero3: Enable XmemCopy Mode.(DCSG00035867)
-BST script change for single PLDM image removal.(DCSG00134638)
-Aero-3: Add debug prints to display SerDes Tx parameters.(DCSG00041624)
-[Aero][Pldm] Print Implementation.(DCSG00012331)
-Coverity improvements.(DCSG00060350)
-Preserve RMC ring buffer contents if metadata is corrupted.(DCSG00022459)
-Update Sasparser path in additional files.(DCSG00010302)
-[Aero][Pldm] Clean PLDM make files.(DCSG00007514)
-SES Access Control - prevent access to DA-SEP.(DCSG00013067)
-Aero: Add limited support for IEEE SGL chains that point to DDR memory for Managed Switch SES.(DCSG00010053)
-Update createSasversion.exe to use getCreds.(DCSG00131581)
-Serial mode support for S25FL512S SPI flash part.(DCSG00054211)
-Create PLI interrupt handler timestamp log.(DCSG00008208)
-Add official support for New Winbond and Macroix Flash chips and block downgrade to older firmware versions.(DCSG00060636)
-MR API: update field in event structure.(DCSG00093331)
-pl: NVMe: fail NVMe init if device requires too much power.(DCSG00016416)
-Aero SAS Performance Enhancement on AMD Rome.(DCSG00066920)
-Add support for custom design.(DCSG00066113)
-Updated BST scripts for latest controller.(DCSG00069955)
-Queue Depth Change for SAS Drives (fix for SAS SMR TSF performance).(DCSG00015057)
-pl: backend PCIe: reconfiguration of PCIe address space without adapter reset.(DCSG00023737)
-Tool to help managing ROP package_type.(DCSG00054920)
-Create a new firmware image that provides an AVSO setting of 0.997V.(DCSG00007958)
-Add support for signing MegaRAID Legacy BIOS CU Images (CTLR) images.(DCSG00143847)
-Ventura/Mercator: backend PCIe: enhance robustness of PCIe port status tracking.(DCSG00018437)
-Handle SATA/NVME DMD.(DCSG00022062)
-AutoCfg Execute Once option is modified..(DCSG00040356 (Port Of EnhancementRequest DCSG00040904)
-Change all BBU messages to CacheVault for controllers using non-battery solution.(DCSG00022793 (Port Of EnhancementRequest DCSG00042680)
-Removal of key caching from SRAM.(DCSG00034355 (Port Of EnhancementRequest DCSG00043827)
-Revert the algorithm which determine if offload is sustainable.(DCSG00079183 (Port Of EnhancementRequest DCSG00099203))
-Multi-Chemistry BMU support.(DCSG00025207 (Port Of EnhancementRequest DCSG00043822)
-Update FW code to Disable SafeMode Boot on OCR using NVDATA..(DCSG00014521 (Port Of EnhancementRequest DCSG00041443)
-Monitoring Drive Performance and Predictive Failure feature to be removed for certain OEM.(DCSG00082984 (Port Of EnhancementRequest DCSG00094732)
-Preserve EPT-PT as boot device after reboot.(DCSG00026421 (Port Of EnhancementRequest DCSG00041444)
-Add NVME Init failure prints.(DCSG00041659 (Port Of EnhancementRequest DCSG00042885)
-CSET Port of EnhancementRequest DCSG00017357: Support dynamic BAR changes from host OS without performing a controller reset..(DCSG00017357 (Port Of EnhancementRequest DCSG00042220))
-Add new MR Event to notify user of PCIe hot reset fail.(DCSG00012583 (Port Of EnhancementRequest DCSG00042943)
-Secure drive Crypto erase behavior change.(DCSG00057696 (Port Of EnhancementRequest DCSG00087586)
-OOB Passthrough Command Restrictions.(DCSG00024579 (Port Of EnhancementRequest DCSG00041490))
-OOB diagnostic Test Improvments.(DCSG00051246 (Port Of EnhancementRequest DCSG00056070)
-PL logic to create VSES instances per Backplane number.(DCSG00069245 (Port Of EnhancementRequest DCSG00076942)
-Change the default behaviour of LED management for ePDs.(DCSG00035830 (Port Of EnhancementRequest DCSG00040903)


Version 51.12.0-3171 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS: 7.12.03.0
	UEFI Driver: 0x070C0300
	HII: 07.12.06.00
	MR FW: 5.120.00-3040
    package 51.12.0-3171
	
Defects:
-Rebuild not possible event is not raised when SATA LD becomes degraded with SAS global hot spare drive is present.(DCSG00020894)
-FW download timeout cleanup in MR FW is causing the command Id to be cleaned up twice.(DCSG00023773)
-Clear drive option not working for FDE drives.(DCSG00022538)
-remove OEM-specific 7.11 conditional check in 7.12 for Defect SCGCQ02128648.(DCSG00018672)
-Update/Downgrade of enclosure firmware hit data exception ERROR.(DCSG00022745)
-Aero Alpha: FW hit Assertion failure in fw\raid\epd.c at line 553: (arrayIndex < MAX_EXTERNAL_ENCLOSURES) when connect more than max encl in multipath.(DCSG00023100)
-XSD changes for increasing DMD on NVMe drives.(DCSG00022794)
-Drives becomes Uncof good after switching personalities with 240 EPDs.(DCSG00024636)
-recon with PD in offline state following OCR may cause pin cache code to go into infinite loop.(DCSG00025468)
-Remove 'thread 0 is reporting error' message.(DCSG00046697)
-pl: NVMe: unexpected task management halt may occur.(DCSG00014455)
-slow builds when changing a print statement.(DCSG00015593)
-VSES may not report valid SES Page 0Ah elements for one of quads attached elements in a UBM backplane..(DCSG00013123)
-Assertion failure in fw\ddf\ddf.c at line 3637 during VD creation.(DCSG00014573)
-Patrol Read: PR doesn't resume for some drives on reboot.(DCSG00016050)
-Subsequent/Future CPLD flash will fail on OEM Specific controller.(DCSG00014579)
-Multiple VSES created on SAS only 8-Slot UBM backplane with duplicate slot assignments.(DCSG00017373)
-BST Failure: After Upgrade to ROP 2806, Subsequent Full Package Flashing is Broken.(DCSG00012371)
-Aero DBU Alpha: Multiple VM's power on/shutdown result to Assertion failure in fw\raid\nvmePRP.c at line 570 saying IO which is not multiple of block size..(DCSG00031582)
-Aero A0: Controller fault EC57 observed on doing individual lane break test on VendorX Gen4 NVMe drive.(DCSG00010317)
-Add 2WIRE_RESET support for I2C backplanes for Aero MR.(DCSG00024536)
-Aero Alpha: FW hit assertion failure in fw\hw\debug\binTrc.c at line 1910: !((ext->remove.step > 0) && (ext->add.step > 0)) while OCR during long weekend.(DCSG00023693)
-Unaddressable Device error status seen with some OEM enclosures.(DCSG00008628)
-Aero: backend PCIe: disallow DPC for PCIe 3 and earlier specific vendor switches.(DCSG00010608)
-IT_SF directory not present in Ventura release zip.(DCSG00010604)
-0x6231 Fault during Sata Task Management.(DCSG00019315)
-Retention test is not invalidating ONFI image immediatley after deallocating data cache.(DCSG00051696)
-Aero DBU Alpha OOB - C0:Assertion failure in fw\hw\inc\3516_inc\memory.h at line 300: linearAddr < MAX_ADDRESSABLE_DRAM_SIZE_BYTES.(DCSG00026978)
-Incorrect matching of image to the controller is causing BST failure.(DCSG00032584)
-PCI SIG Configuration Space Compliance Test Failure - 1_18 Base Address Register.(DCSG00011443)
-Aero Mfg. Page 40 & 41 Update.(DCSG00026402)
-fixes for Arm watchpoints.(DCSG00032994)
-Correction on fix for old DB issue SCGCQ02165711 Aero PA6: Assertion failure in fw\hw\ioa\ioDivertHw.c at line 339 after deleting a JBOD.(DCSG00017556)
-pl: fix unhelpful debug print.(DCSG00010298)
-Aero Alpha: EPD IO Errors during multipath failover.(DCSG00031481)
-UBM Link Config may fail for HBA connector with Phys routed spans CSWs.(DCSG00022691)
-PackEnergy value in log is not displaying the correct value..(DCSG00012212)
-etty log entry missing timestamp.(DCSG00022721)
-Aero: Powered cycled managed switch SES can become inaccessible.(DCSG00021412)
-MR:Config Loss seen for rebooting server after Deleting Logical disk with OS on JBOD installed.(DCSG00058891)
-Skip multipath checking on Atlas SES.(DCSG00026762)
-Coverity Defect.(DCSG00024005)
-L1/L2 flush does not occur when there is an assertion prior to reaching the READY_FOR_OFFLOAD doorbell handling.(DCSG00023509)
-After flushing Pinned Cache, Snapdump does not get initialized.(DCSG00012499)
-IOMMU fault seen when FW crashes with a PL fault.(DCSG00016259)
-avoid exception when booting up with more drives than supported.(DCSG00039857)
-Aero PA7: FW hits assertion failure in fw\raid\epd.c at line 554: (arrayIndex < MAX_EXTERNAL_ENCLOSURES) when connects more than max encl supported.(DCSG00014910)
-Fix the debug message error.(DCSG00013056)
-serialize the whole statement table during the build.(DCSG00032418)
-COLINFO is giving incorrect data after clearing nvram and warm reboot.(DCSG00010570)
-Fix PL Settings Output Compare for IT vs megaraid.(DCSG00026395)
-VD offline/Drive become UBAD after running drive firmware offline update on OEM NVMe drive.(DCSG00026061)
-Aero A0: vSES is created even for managed Atlas (Ibanez) switch.(DCSG00012487)
-Fix invalid references in SnapDump processing during early boot initialization.(DCSG00015304)
-Voltage dropped below the minimum voltage to sustain offload..(DCSG00025767)
-Aero Alpha: FW failed to detect any NVMe drive after doing PDs pulled/push in Ibanez environment.(DCSG00023150)
-ePDS/JBODs not getting created and deleted properly in the test script. Also personality change code needs improvement..(DCSG00058512)
-slow builds when changing a print statement.(DCSG00015316)
-Locate PD fail on SGPIO enclosure when GroupId is disabled in Nvdata.(DCSG00034489)
-When trying to set CC=off using storcli, command fails with error MFI_STAT_INVALID_PARAMETER.(DCSG00021501)
-pl: backend PCIe: EC5B fault.(DCSG00022805)
-Aero Alpha: ERROR: Exception Handler Called for Processor Core = 0 when UG_DG firmware.(DCSG00021487)
-Ventura B0: vSES not reported in Windows 2019 on certain UBM backplane config.(DCSG00026333)
-After rebuilds are complete. Only one copyback is kick-in, and the rest copyback are not kick-in..(DCSG00020536)
-Assert occurred shortly after pulling drive during an active hotspare rebuild of R1 LD with multiple MediaErrors injected on drives that do not support WriteUncorrectable..(DCSG00025297)
-Backplane detection never completes leading to discovery timeout.(DCSG00023081)
-Aero Alpha - COL AMD controller max reboots, controller not found.(DCSG00024977)
-Restrict temporary disabling of TTY logging in flash only for certain CFG dcmd commands.(DCSG00014416)
-pl: backend PCIe: legacy interrupt may not be serviced if interrupt mask fails.(DCSG00010071)
-FW is filling enclConnectorIndex as MR_SAS_CONNECTOR_NONE for Atlas SES.(DCSG00012380)
-Online NVMe drive become UGood after offline drive firmware update without I/O.(DCSG00026088)
-Update Vision Data to Latest Settings.(DCSG00026396)
-FW prints constantly "C0:Completing the CMD with Failure" during Recon w IOs.(DCSG00017587)
-Ventura B0: vSES goes missing after the first controller reset on UBM Ex1 in x8 HFC config.(DCSG00024555)
-Adjust test to avoid overwriting ETTY buffer.(DCSG00010532)
-Fix Static Analysis reported issue #27427 and #27428 in Aero Project.(DCSG00023997)
-Coverity defect fix.(DCSG00041475)
-All "MR Params Page" fields are zeros when checking from FW "dumppages".(DCSG00017358)
-Aero PA7- Hitting KA when doing SED PD pulled/pushed under 2s.(DCSG00013109)
-Aero Alpha: Patrol read not resuming on NVMe drive after controller restart.(DCSG00017454)
-Too many Invalid SGL prints seen on the log..(DCSG00040891)
-pl: discovery failure if PCIe backplane detection is disabled.(DCSG00013397)
-Increase DMD for NVMe drives to 8 Secs.(DCSG00022473)
-remove OEM-specific 7.11 conditional check in 7.12 for Defect SCGCQ02128648.(DCSG00017481)
-MR 7.12 Ventura reports "Failed Chip 0" too many times in FW log during boot up.(DCSG00034242)
-NVMe crypto erase sanitize command is issued in restricted completion mode.(DCSG00032146)
-Atlas Behind Aero: PL Fault 0xEC1A When Performing Backend PCI Resets From Diagnostic Code.(DCSG00042688)
-SCSI REPORT LUNS Data return invalid data.(DCSG00031662)
-Toggle Board is reporting ECC errors on all blocks after approximately one hour since power up..(DCSG00017348)
-Fix MCTP oobCmdInfo[cmdID].packetSeqNumber as previously it is one byte (8 bits), where incoming traffic may used up :16 bits..(DCSG00020940)
-Ventura B0: Incorrect VSES associated to unmanaged PCIe SW enclosure.(DCSG00023764)
-Dev found defect for CSET Port of Defect DCSG00019991: PERC11: NVMe VD IO: 'MptDirectProcessIocError: invalid SGL'.(DCSG00037795)
-HW Workaround:Resizable BARs capability.(DCSG00020103)
-Add additional Enclosure error log messages, SnapDump pd rpm info, and debug improvements..(DCSG00020860)
-Deprecating SAS IO unit page 4 in firmware.(DCSG00031642)
-pl: NVMe: E425 fault after vendor specific device firmware update.(DCSG00012593)
-Secure EPD not restored when pull and insert EPD drive..(DCSG00011549)
-BBU Power Cycle Test: assertion it hit during the test.(DCSG00014421)
-MR: Don't allow the user to change lane speed if UBM is present.(DCSG00012448)
-On Demand snapdump command returned success after snapdump retrieval failed due to snapdump context not initialized.(DCSG00012214)
-Event ID 458 prints %d instead of actual drive count..(DCSG00017334)
-FW doesn't have enough time to generate snapdump before driver kill adapter kicks in.(DCSG00019591)
-Ventura B0: VSES created for every unmanged SW in Mfg 46 single VSES mode.(DCSG00009462)
-Continuous print when BBM is not connected..(DCSG00032155)
-Aero-3: Serdes parameters from NVDATA are not sent to Serdes.(DCSG00022778)
-Fix discrepancy in Maximum device handles between Protocol Layer and MegaRAID Frimware(FW) layer.(DCSG00011826)
-Aero DBU Alpha: VMWARE OS reported Assert, while running IO's on NVM-E JBOD with DCMD.(DCSG00034534)
-Aero DBU Alpha : Driver sends KA , when one of the SMID pending on offline NVMe drive.(DCSG00034100)
-Coverity Defect.(DCSG00023994)
-MR 7.12: iMR firmware does not report driver status when OCR is completed.(DCSG00012612)
-fix %y for binTrc.(DCSG00012190)
-Kill adapter while running JBOD's IO with TM..(DCSG00012350)
-Random supercap discharging/charging messages are appearing in the log.(DCSG00011518)
-Aero PA7 - Incorrect error messages from CLI, with pinned cache foreign import.(DCSG00012215)
-Coverity Defect.(DCSG00023999)
-Storcli returns failure when setting autoconfig to R0 even though autoconfig was successfully changed to R0.(DCSG00013254)
-Block only the led updates from the host to the raided Slots regardless of the personality.(DCSG00037868)
-Update OEM specific jbod bst script.(DCSG00043379)
-The retention test was started when ONFI was not sustainable.(DCSG00012640)
-Flash Filesystem Refresh failed.(DCSG00052870)
-etty logs are flooded EnclSesGetDetailExt & not yeilding useful data.(DCSG00027403)
-Firmware marking online drives to hot spare while deleting another logical drive.(DCSG00020544)
-Aero Alpha: "C0:devH xx IsSMP=1" rolling non-stop while I/Oing across all LDs and drive pull/push in Altas Ibanez HBA environment.(DCSG00024018)
-pl: NVMe: fix a couple of debug issues related to unique identifiers.(DCSG00014628)
-On Locating PD's,LED's are not blinking for drives connected to customer specific SGPIO Backplane.(DCSG00018823)
-pl: backend PCIe: 'pl pci dbgall' causes ring buffer spam.(DCSG00019925)
-Aero PA7: "Assertion failure in fw\cpu\arm\exceptions.c at line 1006" during device discovery due to power cycled enclosure.(DCSG00011561)
-Performance hit due to unnecessary register load.(DCSG00012488)
-Aero : Task Management timeout results in Kill Adapter while running IO's on 4K JBOD.(DCSG00048021)
-Fix Static Analysis reported issue #27382 in Aero Project.(DCSG00024000)
-Memory allocation fails while creating/deleting VDs in loop.(DCSG00014384)
-MR_7.12: User is able to set the save count on iMR ventura.(DCSG00012280)
-NVDATA in wrong location in MR release zip files.(DCSG00009013)
-Aero: NVMe: device not removed if init fails and it then goes missing.(DCSG00013404)
-PL improperly cleaning up and recovering from hot resetting MPI Device (i.e. reinitializing MPI Device failing).(DCSG00032157)
-PL 0x4E00 fault occurs when Task Management Device Resets are issued to different manged switch SESes at the same time.(DCSG00032952)
-pl: UBM SAS max link rate update to phys fails.(DCSG00011896)
-pl: backend PCIe: IO halt following temporary device removal.(DCSG00015943)
-Offload was not sustainable.(DCSG00054867 (Port Of Defect DCSG00058422))
-Allow PCIe IO Unit page 1 link rate debug override option to override BP reported max link rate.(DCSG00042965 (Port Of Defect DCSG00043573)
-Fault 4322 observed on internal 8 phy board.(DCSG00028298 (Port Of Defect DCSG00049041)
-Dev Defect -Firmware asserted in ONFI module on OCR with Pinned cache..(DCSG00025534 (Port Of Defect DCSG00034155)
-Superfluous message for NVME IO with SGL.(DCSG00017353 (Port Of Defect DCSG00033702)
-Aero: PL cannot handle very large SES Page 0Ah from Managed Switch SES for MPI SEP Request.(DCSG00010049 (Port Of Defect DCSG00012692))
-Data Miscompare on drives that are configured as EPD when other EPDs are removed.(DCSG00032922 (Port Of Defect DCSG00038956)
-UBM BP product revision version mismatch b/w SES Page 01 and SCSI Inquiry output.(DCSG00036978 (Port Of Defect DCSG00044345))
-Unable to import foreign config.(DCSG00025975 (Port Of Defect DCSG00033649))
-Patrol Read fails to run on all the online drives when iteration count > 1 and PR maxconcurrentpds < online-drive-count.(DCSG00048576 (Port Of Defect DCSG00058076))
-pl: Ventura/Mercator: device side PCIe link failure following adapter reset.(DCSG00038775 (Port Of Defect DCSG00040712))
-Unable to detect drives behind Sea controller during Windows installation.(DCSG00012569 (Port Of Defect DCSG00013165))
-pl: backend PCIe: incorrect value written to Device Status/Control register during error handling.(DCSG00038289 (Port Of Defect DCSG00038996))
-pl: backend PCIe: debug prints.(DCSG00013387 (Port Of Defect DCSG00014212))
-FW - AMD2P Wave1 - UG bad drive is missing in MR 7.12 FW.(DCSG00026516 (Port Of Defect DCSG00032248))
-iMR hits exception after FW upgrade before OCR then do storcli /c0 get snapdump.(DCSG00060816 (Port Of Defect DCSG00068263))
-pl: Ventura/Mercator: device side PCIe link failure following adapter reset.(DCSG00024652 (Port Of Defect DCSG00040579))
-PL: Device removal event is not sent for hot removed end device.(DCSG00023448 (Port Of Defect DCSG00023450)
-Aero: backend PCIe: 265D fault if PCIe Device Page 2 is read for a SES device.(DCSG00016069 (Port Of Defect DCSG00016108)
-PowerCycle Server after re-purposing controller by ClearNVRAM causes controller not found.(DCSG00062527 (Port Of Defect DCSG00066601))
-Aero: Error on posting a SCSI IO request to Atlas SES can cause IO forever being pended.(DCSG00012605 (Port Of Defect DCSG00012962)
-Cache data is lost after server power pull running IO on R5 and R6.(DCSG00027826 (Port Of Defect DCSG00032505)
-Undefined Instruction exception handler was called.(DCSG00058973 (Port Of Defect DCSG00063868)
-After flashing latest FW and setting factory defaults with JBOD host led mgmnt enabled, the option to set this feature is no longer shown in HII.(DCSG00022039 (Port Of Defect DCSG00033732)
-Invalid number of blocks created causing failed IO for NVME disks.(DCSG00019991 (Port Of Defect DCSG00033703))
-PL : PL fault 0x7C41 is observed.(DCSG00030914 (Port Of Defect DCSG00033477))
-Atlas behind Aero IT: Fault code: 0x4000EDAC while running IOs and TMs.(DCSG00022533 (Port Of Defect DCSG00023799)
-pl: backend PCIe: endpoint or switch is unexpectedly reset in a couple of error cases.(DCSG00030361 (Port Of Defect DCSG00032417)
-Windows powershell shows 48 slots in single VSES mode.(DCSG00022999 (Port Of Defect DCSG00046034)
-Not able to enable JBOD property in Ventura controllers.(DCSG00069029 (Port Of Defect DCSG00071230))
-MR FW failed to arm offload when cache offload was expected to start.(DCSG00065467 (Port Of Defect DCSG00071479)
-FW - AMD2P Wave1 - UG bad drive is missing in MR 7.12 FW.(DCSG00026516 (Port Of Defect DCSG00040993))
-PL: Insertion events for some drives in UBM have the wrong enclosure handle.(DCSG00011802 (Port Of Defect DCSG00011898))
-Controller crashes in certain cases when sending multiple NVME pass through commands.(DCSG00039865 (Port Of Defect DCSG00046624))
-UBM Auto HFC grouping fixes and debug print fixes.(DCSG00012363 (Port Of Defect DCSG00017558)
-Aero: backend PCIe: link failure following link down.(DCSG00043821 (Port Of Defect DCSG00048788))
-Aero: Various faults occur with PCIe clock configuration mismatch between Aero and managed switch (Atlas).(DCSG00012378 (Port Of Defect DCSG00012416))
-U.2 Drives Not Discovered on OEM backplane.(DCSG00044296 (Port Of Defect DCSG00046711))
-relnoteHeadline.(DCSG00010308 (Port Of Defect DCSG00010565))
-OS hangs while formatting VDs.(DCSG00038731 (Port Of Defect DCSG00053814))

EnhancementRequests:
-Add option in XSD to Disable SafeMode Boot on OCR using NVDATA.(DCSG00013302)
-Verify the characterization ecc code in aero works.(DCSG00010696)
-Monitoring Drive Performance and Predictive Failure feature to be removed for certain OEM.(DCSG00082984)
-Adding prints why BBUGood got cleared.(DCSG00026047)
-Implement support for Cross certificate and command - Windows signing using CNG Provider with HSM Protected Key.(DCSG00030211)
-Verify the characterization ecc code in aero works.(DCSG00012864)
-pl: backend PCIe: enhance robustness of PCIe-related MPI event generation.(DCSG00009002)
-Implemented secureSignCNG.exe CLI signing tool for Windows Signing.(DCSG00023491)
-XSD update for the new PL phase.(DCSG00017584)
-Update Sasparser path in additional files.(DCSG00010302)
-Secure drive Crypto erase behavior change.(DCSG00057696)
-updated bst scripts and parent script.(DCSG00026954)
-Aero/Ventura: Misc debug fixes and enhancements.(DCSG00009402)
-Port secureSignBin.exe for MARGAY signing to GCP server environment.(DCSG00040377)
-pl: backend PCIe: PCIe Link Page 3 ineffective when UBM backplane is present.(DCSG00014448)
-Add option in MR PRIVATE API to Disable SafeMode Boot on OCR using NVDATA.(DCSG00012685)
-Remove "Deprecated" word attached to ISE Capable drive variable in MR API Pd Info Properties.(DCSG00014621)
-Aero: Add limited support for IEEE SGL chains that point to DDR memory for Managed Switch SES.(DCSG00010053)
-Python SPDM scripts for Get_Version,Get_Capability, Nego_Algo, Get_Certificate, Get_Digest, Challenge.(DCSG00054553)
-Added tests for 2TB and larger Drives and VDs.(DCSG00019927)
-Update "next learn cycle schedule" to only NVSRAM after TLC completion.(DCSG00034286)
-Add option in MR API to Disable SafeMode Boot on OCR using NVDATA.(DCSG00012688)
-Improve DDF clear result via logging the Failed event.(DCSG00012420)
-separating oem stream based on program.(DCSG00027629)
-Enhance medium error test cases : please refer to CLCA for defect SCGCQ01996272.(DCSG00043884)
-Improve cable breaker mechanism for PERC bst.(DCSG00051824)
-Add new event MR_EVT_PD_PCIE_HOT_RESET_FAILED..(DCSG00015113)
-pl: backend PCIe: allow override of backplane link config for debug.(DCSG00011555)
-Integrate JBOD BST script for OEM controllers.(DCSG00036764)
-Create a new firmware image that provides an AVSO setting of 0.997V.(DCSG00007958)
-Build tools modifications to auto generate source and header files.(DCSG00025402)
-Ventura: Create a custom build script.(DCSG00012169)
-NVMe Device PCIe Configuration Space Access.(DCSG00010545)

	

Version 51.10.0-3038- Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS: 7.10.03.0
	UEFI Driver: 0x070A0400
	HII: 07.10.07.01
	MR FW: 5.100.00-2924
    package 51.10.0-3038

MR 7.10
Defects:
 - offload was not sustainable(DCSG00058005 Port Of Defect DCSG00054867)
 
Version 51.10.0-2837-1 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS: 7.10.03.0
	UEFI Driver: 0x070A0400
	HII: 07.10.07.01
	MR FW: 5.100.00-2723
    package 51.10.0-2837

Defects:
 - PL: PL_INFO_PUIS_FLAGS violates the FW coding standard(SCGCQ01329829)
 - changes for cache offload fpga(SCGCQ01562816)
 - Aero Fpga Cache Offload : flash initialization bug fixes(SCGCQ01566826)
 - onfi commands do not work after switching to nv-dd2 mode(SCGCQ01573392)
 - remove offload wrapper idle workaround(SCGCQ01573650)
 - arm data abort exception	(SCGCQ01580245)
 - Aero Fpga Cache Offload : update generic and PIO mode command sequence as per prog guide(SCGCQ01581424)
 - Fix ONFI timing mode parameter values(SCGCQ01581490)
 - Use 6.25 Mhz timer clock on FPGA	(SCGCQ01593736)
 - Update rbvalid as per toggle data sheet(SCGCQ01595837)
 - read parameters is infinitely looping with failure(SCGCQ01596675)
 - Fix issues related to ONFI flash SLC blocks initialization(SCGCQ01599110)
 - Toggle Aero : Fixing Read Id in sync mode.(SCGCQ01600274)
 - SDMA fixes for Aero ONFI4 transport layer (generic and PIO modes(SCGCQ01605431)
 - Flash controller reset is not working(SCGCQ01605634)
 - Toggle: Factory bad block scan is failing(SCGCQ01616950)
 - Disable Toggle Badblock scan(SCGCQ01616954)
 - data abort when doing symbol lookup(SCGCQ01619012)
 - Fix flash filesystem issues with DDR enabled	(SCGCQ01620670)
 - command descriptor structure issues(SCGCQ01623718)
 - Toggle Bad block scan : data abort exception fix.(SCGCQ01625932)
 - FW hangs during metadata buffer initialization when DDR is disabled(SCGCQ01629361)
 - Toggle COL : wrong page address mask and block address index causing muliplane read\prgram\erase failure.(SCGCQ01635535)
 - Descriptor based offload is failing(SCGCQ01639934)
 - Aero Fpga Col : MSS Reset issue(SCGCQ01665150)
 - fix colReadVerifyOffloadMeta to invalidate cache before issuing CDMA read descriptor command(SCGCQ01670321)
 - Fix scrambler initialization(SCGCQ01671243)
 - Update DFI init functions to set Fc1DfiInitComplete(SCGCQ01676019)
 -(SCGCQ01676332)
 - Signature generation is not working.(SCGCQ01676706)
 - multiplane erase command are not reporting failure for known manufacturing bad blocks(SCGCQ01685652)
 - Aero COL FPGA : Fix value of pages per block(SCGCQ01687533)
 - Aero COL: Issues with flash controller thread management(SCGCQ01687747)
 - Aero COL FPGA: Skip Bad block scan during Col HW initialize at bootup(SCGCQ01697702)
 - enable badblock scan(SCGCQ01698187)
 - Remove pinned cache check for single image on FPGA in colPrepareForOffloadEvent routine(SCGCQ01698348)
 - Bad blocks are not skipped during erase operation.(SCGCQ01713643)
 - Aero COL FPGA: Reset DIS CRC and checksum to default values before doing restore(SCGCQ01714686)
 - Validate argument count for debug API's(SCGCQ01715682)
 - FW hit assert when both SOFs are bad, but atleast one of EOF is good while checking offload image(SCGCQ01727288)
 - The read retry code is hitting an ASSERT on toggle(SCGCQ01762159)
 - Modify colOnfiInitSlcBlocks to use copyback command(SCGCQ01763316)
 - Control Plane Address - currently in common code(SCGCQ01763460)
 - Ventura README.doc in NVDATA folder mis-spelled "Mercator"(SCGCQ01764256)
 - Addressing rebase issues.(SCGCQ01765357)
 - uncorrectible ecc error on 2nd flash controller reported during restore(SCGCQ01772608)
 - Debug Command 'coldesc' does not display cache offload blocks correctly.(SCGCQ01787987)
 - the 'make ventmr' command is currently building aero cache offload files(SCGCQ01799420)
 - the 'make ventmr' command is currently building aero cache offload files(SCGCQ01799421)
 - There is not way to alert LSA if the snap dump properties are changed.(SCGCQ01801629)
 - Aero PA0.6 - No IO BW and watchdog timeout with large 80x R0 and 80x EPD config(SCGCQ01804425)
 - Restore failing due to incorrect ECC(SCGCQ01833380)
 - Restore on 2nd offload region is failing(SCGCQ01835597)
 - BB table is corrupted if bad block factory scan is run after an offload completes.(SCGCQ01835599)
 - pl: backend PCIe: potential race condition during switch downstream port link up(SCGCQ01837083)
 - Aero PA0.6 - Can't update to latest firmware because of profile changes(SCGCQ01846131)
 - Aero PA0.7: Changing profile to 31 and reboot resulted in firmware stuck in reset cycle(SCGCQ01848037)
 - SmrZacHM/SmrZacHA not in reverse orders between the Big Endian and Little Endian	(SCGCQ01848090)
 - No Flush when expected during a COL test.(SCGCQ01849292)
 - Aero PA0.7: FW breaks into montask with exceptional core handling error(SCGCQ01850596)
 - PL Fault 0x6001 occurred while running IOs + Task Management requests(SCGCQ01850755)
 - Aero BST failure, Raid LD tgtId does not persist through OCR(SCGCQ01857416)
 - pl UBM: Elrond Ex1 - Cannot see NVMe drive in slot 17 (offset = 16(SCGCQ01858852)
 - 0x6004 Fault running TM only test(SCGCQ01858982)
 - Mismatch between data coming from Page2 and PageA in vSES(SCGCQ01859095)
 - Firmware fault when continuously creating and deleting VDs/EPDs using attached batch script(SCGCQ01864769)
 - Disable supportJBOD for Ventura JBOD personality and Aero.(SCGCQ01865888)
 - pl: Locate LED on SFF-TA-1005 Ux4 backplanes configured in x16 or x8 HFC emulation mode is not activated by storcli command(SCGCQ01866800)
 - Ventura: Fault 0x2805 encounted if one configures NVME and AutoPortEnable at the same time(SCGCQ01868375)
 - Aero3: Serdes interrupt handlers are not compiled in for Aero(SCGCQ01868574)
 - MPI 2.6: Fix definition of Signature0 field and PSOC download definition(SCGCQ01868634)
 - pl: port enable timeout and discovery failure with multiple VPP device configurations(SCGCQ01870862)
 - misc colDebug module cleanup(SCGCQ01871049)
 - Library might incorrectly set program/erase request bit when flash suspend feature enabled.(SCGCQ01873461)
 - Dev Defect: Fix COL Debug API to read and write to registers(SCGCQ01876735)
 - pl: vSES reports incorrect product revision level in SES page 1(SCGCQ01877030)
 - pl SFF-TA-1005: All Ux4 drives are not discovered in x8 or x16 HFC mode while hot-plugging(SCGCQ01877041)
 - IO's can time-out after controller receives an unconfirmed response from a drive(SCGCQ01878174)
 - pl UBM SFF-TA-1005: Locate LED cannot be turned off after diag reset(SCGCQ01884070)
 - GOLDENX: Ventura image not accepted by GoldenX(SCGCQ01884228)
 - Critical Message " maximum supported count of 256 disks" received with MaX PDs(SCGCQ01884237)
 - pl: backend PCIe: link fails to come up after a surprise down(SCGCQ01886012)
 - Update the common header file to avoid compilation fail.	(SCGCQ01886583)
 - Ventura: NVMe I2C Backplane Detection fails on HBA connectors C2/C3 resulting in Slots not responding to LED updates(SCGCQ01886810)
 - Ventura: PLI control requests may return incorrect status when backend PCIe support is disabled	(SCGCQ01887433)
 - misc colDebug module cleanup(SCGCQ01889377)
 - Aero:GHS/DHS is detecting as HSP after push/pull(SCGCQ01889549
 - Cached Discarded during boot	(SCGCQ01889785)
 - SPILIB: Winbond 128Mbit (16MB(SCGCQ01890038)
 - PL vSES: PCIe switch downstream virtual ports report SAS address of zero in SES page 0xA(SCGCQ01891238)
 - Ventura: SCGCQ01800775 and SCGCQ01792449 both require a minimum initial firmwmare download size of 1.25K. MCTP will fail due to small payload size(SCGCQ01891838)
 - MPI 2.6: Fix definition of SGLs in TOOLBOX_LANE_MARGINING_REQUEST(SCGCQ01896537)
 - pl UBM: Ux4 drives not discovered in Polling Mode with HFCx16 and x8(SCGCQ01896578)
 - PL UBM : SAS, SATA drives in Elrond UBM backplane(SFF-TA-1005(SCGCQ01897599)
 - Remove the unnecessary snapdump when importing foreign configuration(SCGCQ01897914)
 - Ventura: OEM SW Enclosure Amber LED stays on after reboot(SCGCQ01898852)
 - FW hits a data abort when both EOF are bad(SCGCQ01902153)
 - Fixes in the fusion descriptor queues dumping routine(SCGCQ01902218)
 - Ventura/Aero: Firmware Upload COMPLETE type fails if and SGE is too large(SCGCQ01903658)
 - SOFA is failing meta signature check(SCGCQ01905135)
 - [vSES] Vendor ID and Product ID of Configuration diagnostic page uses hardcoded values.(SCGCQ01906013)
 - pl: NVMe: 6060 fault(SCGCQ01909264)
 - Incorrect clearing of GUID to target ID map table during EPD creation(SCGCQ01909341)
 - Comments in plStates.c and plStates.h are wrong(SCGCQ01909770)
 - Implement SCGCQ01880847 in MR 7.9: Hit PL Fault 00005862 LinkRegister 01439171 During CC With Triple Media Errors On R60 4K Drives(SCGCQ01909922)
 - colFlashEraseRegion might incorrectly erase data block.(SCGCQ01911889)
 - Add logic to identify bad blocks when SOF is not available/invalid(SCGCQ01911893)
 - Fw hit drvspinup.c when wake up from hibernation(SCGCQ01912208)
 - Grammatical errors in Driver Health Manager Menu in UEFI.(SCGCQ01913906)
 - MR7.8: CTRL does not detect drives with SAS3.5CtrlFw_Ventura_Ph_9.0 08.250.09.00 and 10 as well(SCGCQ01914192)
 - Fix memory allocation for PtrRestoreMetaSof buffer(SCGCQ01915514)
 - pl: backend PCIe: bug when setting up direct attached PL structures(SCGCQ01915755)
 - iMR 16i + ux2: ctrl hit exception after delete config(SCGCQ01915759)
 - NVCache device failed, cannot support data retention(SCGCQ01917935)
 - pl: NVMe: device not removed following NVMe init failure(SCGCQ01918703)
 - pl UBM: Drives are not detected if they are reconnected back within polling interval(SCGCQ01918736)
 - Aero PA0.8: (Vision(SCGCQ01918865)
 - Aero FW PKG Pkg-50.9.0-1753/When flashing controller, it is breaking into Montask(SCGCQ01919878)
 - Command " storcli /c0/vall delete " indefinitely hangs with FW pkg 1751(SCGCQ01919989)
 - Link information is incorrect for Ux2 & Ux4 midplanes(SCGCQ01920596)
 - VDs are not foreign as expected(SCGCQ01921251)
 - Adding asserts for pli control requests during PL initialization(SCGCQ01922143)
 - Aero MR: ctlr hang after sblib calloc call(SCGCQ01922234)
 - pl: backend PCIe: additional robustness for hot reset during SAS cycle case(SCGCQ01922270)
 - compilation error(SCGCQ01922280)
 - fix one of the extended image checksum(SCGCQ01922302)
 - pl UBM: Ex1 Elrond SFF-TA-1005 UBM back plane with SAS drives only connected to a Ventura HBA leads to a PL fault(SCGCQ01924946)
 - incorrect date for snapdump files	(SCGCQ01925056)
 - Task management being issued to a vSES device handle causes the firmware to crash(SCGCQ01925931)
 - cleanup snapdump function which dumps descriptor info(SCGCQ01926130)
 - PL: 0xED22 fault when SFF-TA-1005 UBM Ex1 SAS drives are connected to HBA connector 1 and NVMe drives on Ex1 are connected to connector 2(SCGCQ01926357)
 - PL : SATA initialization may be completed even though there is a failed set feature command(SCGCQ01926787)
 - PL SATL : Host IOs may timeout after a sanitize command that completes with an error(SCGCQ01929016)
 - (SATA Only(SCGCQ01931146)
 - vSES: Remove, RRAbort and Missing bits in array device element are not getting updated in element status page.(SCGCQ01932394)
 - pl: backend PCIe: device not unblocked following rediscovery in reduced requirements mode(SCGCQ01932972)
 - Aero3: Initial Board Bringup Fixes(SCGCQ01932994)
 - Command is not supported CLI error when trying to set termlog=on(SCGCQ01933158)
 - vSES SES Page 0Ah may report same SAS address for two elements during hot remove/add of NVMe devices(SCGCQ01934145)
 - Aero3 Ring buffer prints indicate constant receipt of PMU messages from M0(SCGCQ01934152)
 - Aero: backend PCIe: default link rate should be 16GT/s(SCGCQ01934903)
 - PL SATL: Firmware Tries to Double Free Resource Mid(SCGCQ01934945)
 - Aero3: OOB burst/idle times are not correct(SCGCQ01936080)
 - Ventura: Use full Slot Cap Physical Slot Number field info for PCIe SW attached device slot enumeration(SCGCQ01936123)
 - Aero3: RMC workaround updates from Ventura	(SCGCQ01936155)
 - After OCR configured pd's moved to Foreign and fails to import in a PD goes bad during boot. The all subsequent drives are foreign.(SCGCQ01936308)
 - [7.9] MR BST failure : Firmware crashes with C0:chainMidFifoIsr: iopIntSts 800081(SCGCQ01936354)
 - Aero3: Spurious CIB interrupt messages in ring buffer(SCGCQ01936912)
 - log dump all command not working on Ventura controllers(SCGCQ01937037)
 - 0x6001 Fault while running IOs and doing cable pulls(SCGCQ01937141)
 - PL SATL : Sanitize operation may be completed with error even though drive did not report error(SCGCQ01937180)
 - Aero: backend PCIe: PDB PLL is reinitialized when it's already locked(SCGCQ01937600)
 - Aero3: Link not established interrupts are not being processed for all phys(SCGCQ01937617)
 - pl: ED00 fault observed on crusader 16i when only Bottom part of Ux4 is connected to the core closest to PCIe slot(SCGCQ01938275)
 - Aero3: CSW M0 firmware version 642(SCGCQ01938307)
 - Aero DDR: Updates to DDRlib for operation at 1600 MT/s(SCGCQ01940449)
 - OCR/KA (if OCR is disabled(SCGCQ01940516)
 - Aero3: Boot Algorithm indicates that sector 1 of OCM is invalid(SCGCQ01940518)
 - Aero: backend PCIe: fix usage of uninitialized variable	(SCGCQ01941171)
 - If SBRReloadEn bit is set in Host Diagnostic register and AHR is issued from host, the AHR never completes.(SCGCQ01941995)
 - Aero-3: Aero PL version not used	(SCGCQ01942093)
 - vSES: CRIT or NON CRIT bits in Enclosure Status Diagnostic page are never set.(SCGCQ01942781)
 - Aero3: Phy interrupt enables not set correctly(SCGCQ01943122)
 - Ventura : UBM change detection polling may not start in mixed backplane topology(SCGCQ01943828)
 - pl: VirtualSES do not show up in Windows when an SFF-TA-1005 UBM backplane with slot offset greater than 16 is connected to a Crusader 16i HBA(SCGCQ01944117)
 - Aero: FWUP fails after second reset after bad image update attempt(SCGCQ01944168)
 - Aero 3: CSW M0 firmware change (ver 643(SCGCQ01945002)
 - Complete AIs from review of code (U32/U64, LdSizeGet, PdSizeGet(SCGCQ01945018)
 - uninitialized variable in code(SCGCQ01947791)
 - Drops upto-7% OLTP for 256K/QD64 in NVMe/Win AND '-7% R0/16K/SRQD256(SCGCQ01948592)
 - Incorrect checks for LD invalid cases during IO processing caused data abort(SCGCQ01950906)
 - power interruption during cache offload setup and erroneous FLASH region change(SCGCQ01957254)
 - Locate LED is non-functional for NVMe drives when we have a Switch attached enclosure as well as a Direct Attached enclosure(SCGCQ01957408)
 - fix poor performance programming NAND(SCGCQ01958517)
 - OCR/warm boot followed by power cycle causes a recondition(SCGCQ01959158)
 - Setting controller "maintainpdfailhistory" does not work	(SCGCQ01959665)
 - vSES : ENCLOSURE BYPASSED B bit set when Missing bit is set via Send diagnostics command(SCGCQ01960090)
 - Ventura B0: SES command to clear the CRIT or NON-CRIT bits doesn't clear the same under Enclosure Status diagnostic page(SCGCQ01960863
 - vSES Doc: Update VSES document to reflect support for control/status element fields.(SCGCQ01961487)
 - Update signature for xsd files.(SCGCQ01961817)
 - Customer specific back plane not detected in the latest code phase(SCGCQ01961997)
 - Evaluate disableSESManagement setting for various modes in Aero/Ventura.(SCGCQ01962733)
 - OEM NVMe backplane I2c entries in NVDATA does not match the specific board(SCGCQ01962861)
 - Performance Test fails - DC/EC Configs - Windows/Linux Configs(SCGCQ01963941)
 - [MR 7.9] Data Abort exception during copyback and OCR cycles(SCGCQ01965125)
 - Only compare hash size for sblib authenticate(SCGCQ01965627)
 - MR_7.9: ERROR: Exception Handler Called for Processor Core = 0 after firing get snapdump.(SCGCQ01966612)
 - NvramDumpAllNvramDumpAll() missing from Snapdump(SCGCQ01966762)
 - During Firmware update, the message displayed for unsuccessfully updating MegaRAID card will be more descriptive and more compattbile with previous MegaRAID products.(SCGCQ01967058)
 - LSA7.9: When Prepare for removal is performed on all the UG Drives, click on Adv/simple configurations should be grayed out(SCGCQ01968110)
 - Data Abort Exception when Enclosure Status Page has "unrecov" bit set and PDAllowedOps command is issued on the enclosure PD(SCGCQ01968331)
 - Move OCM ECC error scrubbing logic to interrupt context(SCGCQ01970027)
 - PL Fault 00005853, while doing two copyback operations on lds with different block size.(SCGCQ01970744)
 - Incorrect clean up on cmd error completion for MFI passthru cmd with incorrect data length(SCGCQ01971319)
 - MR_7.9: Pre-boot generated snapdump has Invalid timestamp.(SCGCQ01973003)
 - When discarding a pinned cache and rebooting, discard the cache message observed(SCGCQ01973033)
 - Erase entire flash after erasing BB table at mpi0 for toggle	(SCGCQ01973139)
 - After importing a VD with pinned cache, a Consistency Check starts instead of Background Initialization.(SCGCQ01973185)
 - OCM copy not covering full amount(SCGCQ01973321)
 - PL: SAS Drives Take a Long Time to Link Up and Are Not Discovered Correctly(SCGCQ01973566)
 - Fix Manpage6 dump from cfgi interface in megamon	(SCGCQ01976253)
 - Unable to do offload after first learn cycle is issued.(SCGCQ01976816)
 - PERC10.4:ONFI: BBLIST RECLAIMALL does not purge factory bad blocks(SCGCQ01978319)
 - FW crashed with Assertion failure in fw\raid\taskman.c at line 360(SCGCQ01978405)
 - Spelling mistake in FW string Controller cache bas been lost	(SCGCQ01979916)
 - OOB max packet size gets reset to 80 after controller resets a few time(SCGCQ01982382)
 - Aero UTP: Firmware hung during new drives inserted with autoconfig=r0(SCGCQ01982809)
 - Incorrect offset value for reserved fields in MR Params Page 0(SCGCQ01983364)
 - After eFuse update successful message controller hangs(SCGCQ01983547)
 - Aero A0 UTP - MR NVDATA does not advertise Gen4 Link Rate(SCGCQ01985204)
 - Dev Defect - Revert SCGCQ01900886: Aero 0.7:After importing a VD CC starts instead of BGI.(SCGCQ01986228)
 - Smart Recovery prints are not seen in FW log during bad block testing.(SCGCQ01987211)
 - New state required for RMC Ring Buffer parser(SCGCQ01987243)
 - rror reading device chemistry. I2C Error = 0xa during COL test with CC and degraded VD.(SCGCQ01988055)
 - Firmware hung after a few cycle of COL(SCGCQ01988177)
 - Could get a false assert on an iMR card in a surprise power down state with traffic.(SCGCQ01990005)
 - Firmware exception when remove and reinsert NVMe drives multiple times on enclosures(SCGCQ01990092)
 - colbb reclaim all is not clearing scolFlashHwConfig->ColHwStatus.ONFI_STATUS_BAD_BLOCKS_EXCEED_LIMIT bit(SCGCQ01990501)
 - RMC ring buffer not logged appropriately for multiple cycles(SCGCQ01990657)
 - Fix Cn to clear COL_INFO and COL_NVRAM(SCGCQ01991852)
 - AERO : ibuttonless: "No primary ibutton present"; "Ibuttonless case: Upgrade key is not present"(SCGCQ01993279)
 - Dev Defect : BGI Enhanced(SCGCQ01993345)
 - FW region lock promotion issue(SCGCQ01993737)
 - Data corruption seems with WB only R5/6 volumes that are unmap capable(SCGCQ01993738)
 - Aero A0 (Power9): Data Abort Exception on the 1154 th debugOcr cycle(SCGCQ01994852)
 - pl: backend PCIe: ED06 fault(SCGCQ01994860)
 - set_factory_defaults issue(SCGCQ01995721)
 - Secure Erase operations are blocked for JBODs on iMR(SCGCQ01999048)
 - Aero A0 UTP: FW hangs at SOD(SCGCQ02005541)
 - Dev defect to revert back the temporary solution for defect SCGCQ01802513 once PL ER SCGCQ01817424 is implemented(SCGCQ02006873)
 - The code was not fixing the check condition of the drive was a system drive.(SCGCQ02010078)
 - AERO: Lastest ROP FWpkg 2060, HII will disappear in system bios(SCGCQ02010333)
 - Aero UTP: flashing 8i ROP on to a EVT 16i controller is not blocked(SCGCQ02011046)
 - AERO: FW hit Assertion failure in fw\dm\src\devMgr.c at line 889 when connecting multipath maxconfig 240Pds(SCGCQ02011149)
 - Controller Fatal Error is observed when Guest OS is reset from host in VMware environment(SCGCQ02011203)
 - Read Eye Training prep is failing(SCGCQ02011239)
 - Fix startcol to do shell halt before setting offload request(SCGCQ02015710)
 - Aero- Hitting data integrity issue on R1 while running I/O across all RAID levels(SCGCQ02016614)
 - Read Eye Training prep is failing(SCGCQ02017278)
 - Coverity Uninitialized scalar variable(SCGCQ02017356)
 - TRNG core not given enough time to initialize(SCGCQ02017399)
 - Coverity: CID 21985 (#1 of 1): Uninitialized pointer read (UNINIT)ptrPrpList when calling mprintf in dm.c:1240(SCGCQ02017402)
 - Coverity: CID 21986 (#1 of 1): Out-of-bounds read.Overrunning array of 4092 bytes at byte offset 4096 at i2COobMgmt.c:3119(SCGCQ02017453)
 - skip the link test if there is no qualifying pd attached(SCGCQ02018014)
 - Ventura encounters an exception on boot(SCGCQ02022767)
 - pliTaskMgmt() returns ISTATUS_DEVICE_NOT_REGISTERED for a DA SEP(SCGCQ02022790)
 - Aero A0 UTP - Exception During Storcli /c0/ex/sx set taskmgmt reset with EPDs(SCGCQ02022834)
 - RAID 5 write performance out of spec.(SCGCQ02023559)
 - Assertion failure in fw\col_common\src\colOnfi.c(SCGCQ02024395)
 - Fix malformed format strings in print statements(SCGCQ02027468)
 - Fix Static Analysis Tool reported defect 19749 in Aero Project(SCGCQ02030077)
 - Coverity reporting firmware is accessing an array beyond the last element(SCGCQ02030081)
 - Coverity Uninitialized scalar variable(SCGCQ02030128)
 - Fixing static analysis tool reported issue(SCGCQ02030133)
 - Fixing static analysis tool reported issue(SCGCQ02030137)
 - Fix wrong memory allocation size for debug information of a debug function.(SCGCQ02030143)
 - fix unchecked input to debug function.(SCGCQ02030147)
 - Fix Static Tool Analysis reported defect # 21737 in Aero Project(SCGCQ02030148)
 - Initialize local variable used for an aborted command(SCGCQ02030152)
 - Return value for the unmap capability check is ignored when rebuild is started(SCGCQ02030154)
 - Wrong argument used in sizeof(SCGCQ02030157)
 - Un-Hide Drive Group is enabled after hiding a VD in HII(SCGCQ02032483)
 - Oscillating SES Diag Page 2 return status code can cause controller to not complete SOD(SCGCQ02032510)
 - Aero - Clear Config or Initialization VDs triggered "CmdBlocked: Clear is running on PDx" rolling(SCGCQ02033666)
 - Unexpected behavior when doing a warm reboot following Injecting DDR Uncorrectable ECC Error.(SCGCQ02033844)
 - VD encryption fails in the present of DHS(SCGCQ02034438)
 - excess debug message "C0: DASEP found dI fb t d" print from OS bootup.(SCGCQ02035956)
 - The hiberfil.sys is not written correctly, causing wake up from hibernation to fail(SCGCQ02035987)
 - StorCLI does not show secure boot pending key update after image flashed with new key(SCGCQ02036045)
 - L1,L2 & OCM flush is taking around 9 msec and causing COL failure on battery based controllers(SCGCQ02037299)
 - Aero:LSA-LSA displays " Raid 60 requires minimum of 6 Physical Drive(s) "instead of 8(SCGCQ02038229)
 - EPAK is not enabled prior to flushing cache(SCGCQ02040475)
 - Aero A0 UTP - Atlas Config NVMe3 TM + Cable pull/push results in CORE0 fault and OCR(SCGCQ02041132)
 - Snapdump capture fails when COL restore occurs with ECC errors(SCGCQ02041663)
 - Fix the memory allocation issue for diag test(SCGCQ02042041)
 - Task Mgmt-Timed Out result to Driver Initiated Kill Adapter.(SCGCQ02042364)
 - coverity:CID 22127 (#1 of 1): Out-of-bounds access (ARRAY_VS_SINGLETON) 20. at colToggle.c:457(SCGCQ02042954)
 - "Invalid arguments" message displayed for "set bootdrive=on" command.(SCGCQ02043633)
 - Toshiba NAND Flash Validation:MR FW is not printing ONFI Params page in correct byte order(SCGCQ02045084)
 - Misc fixes in colWrapper.c (failure analysis code)(SCGCQ02045427)
 - Aero UTP : controller doesn't get new EID assigned after manual BDF change(SCGCQ02047343)
 - Avoid releasing I2C bus when I2C operation(Read/Write(SCGCQ02050528)
 - The locate functionality does not work for the bad PD connected to the slots 4-7.(SCGCQ02053027)
 - When host is changing the personality, must complete all flush/changes before returning success to host. User may cut power with good status before all flush/changes are complete.(SCGCQ02053527)
 - Upgrade to latest MR 7.10 firmware failed with error " Downgrade below ver 50.4 in JBOD personality not allowed"(SCGCQ02053528)
 - FW is reporting Battery information in the log every minute(SCGCQ02055351)
 - Aero UTP: Deleted global HSP drive comes back after a reboot in JBOD personality(SCGCQ02056629)
 - Aero- FW hits Exception after disconecting multipath to make LDs offline	(SCGCQ02058262)
 - Aero UTP: Assertion failure during WJ write following a COL event when a VD goes through RLM(SCGCQ02058372)
 - NVRAM Registers were not getting intialized for Ventura in 7.10, causing Exceptions or Halts after OCRs(SCGCQ02060073)
 - Improve error handling for FW hang while waiting for DMA engine to halt(SCGCQ02061724)
 - There is a possibility of missing a NVRAM cache-flush when SBR-reload bit is enabled after Personality change and powercycle with IO(SCGCQ02061792)
 - copyright change in vision psoc library(SCGCQ02064039)
 - MR_7.9_Huawei: Assertion failure in fw\dm\src\dm.c at line 2074 while PD FW upgrade/downgrade with IO's on NVMe drives(SCGCQ02065611)
 - A bunch of firmware print from debugger "C0:RM_CheckForSataBBM _DCDB_Other command types_SCSI_COMMAND 3(SCGCQ02066875)
 - Fix missing snapdump trigger type information.(SCGCQ02067042)
 - Aero UTP: On-demand snapdump lost when created before learn cycle on new SCAP when there is no VD(SCGCQ02071231)
 - Stop SES Diag Page 2 request during SOD if max time per enclosure is exceeded(SCGCQ02073749)
 - Update UpdateupgradablePSOC & upgradableCPLD fields in Controller Info hwPresent structure(SCGCQ02076441)
 - MR7.10-9480-8i8e: DC during Single Dip COL Using Wingman Automation(SCGCQ02077953)
 - Avoid unnecessary writing of SBR on a profile update. SBR update should only occur on personality update(SCGCQ02078894)
 - Too much prints on the TTY log(SCGCQ02081012)
 - Controller hangs after personality is changed and user issues a warm reboot(SCGCQ02083620)
 - Spelling for SnapDump appears with "Sending SanpDump" once log file is opened.(SCGCQ02085505)
 - MR 7.10 - Performance drop on 2x8Dr R0 HDD, DC setup(SCGCQ02090424)
 - Offline PD firmware downloads are taking 2 minutes to complete(SCGCQ02091861)
 - test tool is reporting learn cycle restarted	(SCGCQ02093653)
 - 9580-8i8e controller hits an exception, when connected to UBM(SCGCQ02098109)
 - [MR 7.10] ETTY flooded with FPChangeCmdBlock prints	(SCGCQ02101260)
 - MR7.10 imr after removed driver module then go to debugger type mem hit montask(SCGCQ02103930)
 - Host issued FP cmd to sysPD with invalid DevH may not be handled correctly(SCGCQ02112563)
 - Changes missed in SCGCQ02083613: CSET: FW not logging events if it doesn't get all the keys. - (SCGCQ02079256)(SCGCQ02123320)
 - NVMe Drive goes missing after running PD Pull Push Script in loop(SCGCQ02123786)
 - After reboot the Setup, the Boot Device will be to reset in HII(SCGCQ02127915)
 - Win;Lin;VenturaMR 7.10_RC: -6 to -16% drops in RW, OLTP in RAID0 in 16 DC/64 EC - 12G SAS,6G SATA HDD config(SCGCQ02132634)
 - Storcli returns success on trying to set 4K JBOD as boot drive.(SCGCQ02172264)
 - FW crashes with Data exception abort while PD FW flash in offline mode E(SCGCQ02173408)
 - Performance issue with Patrol Read on 9460-8i(SCGCQ02175420)
 - Misc Bug Fixes to FPGA project - cache offload(SCGCQ01571820)
 - Flash memory controller data structures are not in correct file.(SCGCQ01579793)
 - Fix issues related to ONFI get/set features commands in NV-DDR2/DDR3 mode.(SCGCQ01593697)
 - remove COL_FMC_DDRLESS_FPGA define(SCGCQ01600838)
 - Miscellaneous fixes in colDebug.c(SCGCQ01617054)
 - Reading parameter page copy with index>0 broken by earlier SDMA fixes(SCGCQ01625091)
 - Aero Fpga Col : move DataSeqPrepare back into DataTransferfunction(SCGCQ01627034)
 - Compilation Issue for aeromr.(SCGCQ01627801)
 - cleanup colPrepareOffloadMemList(SCGCQ01628793)
 - Block and Page boundary condition checks(SCGCQ01639993)
 - Restoring an offload image is not working(SCGCQ01670491)
 - restore is reporting failure(SCGCQ01683394)
 - Bad block reclaimall command re-populates bad block table(SCGCQ01684909)
 - bad block table changes for aero	(SCGCQ01698425)
 - CDMA bug fixes(SCGCQ01713700)
 - Aero COL FPGA: Fix usage of disableBBR flag in descriptor(SCGCQ01718297)
 - implement change column usage in the read parameter(SCGCQ01737950)
 - Aero Cache Offload - Fix compilation errors with non fpga build(SCGCQ01746176)
 - Fix compilation errors with ventimr build with COL code in place(SCGCQ01748091)
 - fix avenger compile error in the aero cache offload common code(SCGCQ01789573)
 - Good Pointer Region should be erased.(SCGCQ01867845)
 - Update CRC for entire BB table structure written to NAND(SCGCQ01868910)
 - pl: SAS/SATA devices not discovered with partial backplane configuration(SCGCQ01870842)
 - Fix Cache Offload BST (Ventura/Aero	(SCGCQ01873018)
 - Aero PA0.7 - Can't import foreign config (2 pd R0 split across 2 pcie switches(SCGCQ01875226)
 - On an 840 controller flashed with Aero with 4 ENC’s attached to one port, deleting the arrays that are created in all 4 enclosures, FW breaks into montask.(SCGCQ01876863)
 - PL: NVMe drives do not link up on non Ex4 backplane attached to an MR board(SCGCQ01878217)
 - pl dbg generate PL fault 4330(SCGCQ01881775)
 - pl: backend PCIe: parent switch port lookup may generate incorrect pointer(SCGCQ01883220)
 - Fix issues found in new function on IO path	(SCGCQ01884168)
 - Flash FS gets created on mpi0 even though mpi0 is reserved(SCGCQ01885763)
 - Aero PA0.7: Talladega/Vision - Max OCR counter remains as MAX after system power cycle(SCGCQ01891355)
 - pl: NVMe: E40A fault if WRPROTECT or RDPROTECT is nonzero(SCGCQ01892105)
 - Ventura: Discovery may not complete, timeout on 94xx-8i HBA(SCGCQ01904851)
 - Update colReadVerifyOffMetaSof to return good status if atleast one of SOFA/B passes(SCGCQ01905317)
 - First discovery failed to complete with 120 seconds(SCGCQ01906628)
 - Display mpi status for each fc/cs separately.(SCGCQ01911898)
 -	(SCGCQ01912662)
 - pl: backend PCIe: hot reset not issued on error if link is not fully initialized(SCGCQ01914063)
 - Aero PA0.8: 'dm setDmd' command not working(SCGCQ01916089)
 - Ventura: IOC init may fail with Host Page Size Invalid LogInfo on backend PCIe disabled FW(SCGCQ01916779)
 - Aero PA0.8 : After Config Clear and setting FW autoconfig to offmode and OCR, pd still comes up as JBOD(EPD(SCGCQ01922140)
 - Ventura RMC: AHR causes host to reboot.(SCGCQ01922333)
 - Cleanup colDbgSetSmartRec to use logical offset(SCGCQ01924892)
 - cleanup snapdump function which dumps descriptor info(SCGCQ01926108)
 - pl UBM: NVMe drive behind Ex1 Elrond not discovered with PCIe switch in the topology(SCGCQ01932776)
 - Fix read retry attempt count in restore fail summary(SCGCQ01932971)
 - Aero3 Fault 431b - unexpected interrupt(SCGCQ01934151)
 - Wrong completion routine being called for aborted NVMe Encapsulated commands(SCGCQ01934165)
 - pl: backend PCIe: couple of issues with PCIe Switch Page 1(SCGCQ01934173)
 - Aero3: RMC changes necessary for complete boot.	(SCGCQ01934925)
 - Aero: ARM cache and MMU throwing exceptions during initialization(SCGCQ01936751)
 - Aero: backend PCIe: lane margining register accesses fail(SCGCQ01937082)
 - COL BST is failing(SCGCQ01937632)
 - Firmware hits Kill Adapter when create/initialize R0 VD using 4k drive.(SCGCQ01937998)
 - Fix CPU exception when updating BVDs while creating LDs in iMR BST(SCGCQ01938009)
 - Aero: backend PCIe: PDB PLL SSC should be enabled by default(SCGCQ01940659)
 - Ventura: FW may fail FastPath IOs to NVMe devices with bad device handle error.(SCGCQ01942983)
 - IO Unit Page 7 reports 0XFF for PCIeSpeed(SCGCQ01943129)
 - uninitialized variable(SCGCQ01943843)
 - Aero ROP 1539 is not hitting 3M IOPs(SCGCQ01943881)
 - Unmap command are rejected(SCGCQ01952450)
 - pl UBM: Firmware hit PL fault ed00 when pull/insert multiple drives(SCGCQ01957716)
 - Handle the error in mode page config to avoid the deadlock in dism state machine(SCGCQ01962045)
 - Hot plugging external SAS cables to Port 0 of 9400-16e HBA is not detected(SCGCQ01962567)
 - SBR Reload feature resulting in MR firmware hang on the restart(SCGCQ01962772)
 - Ventura iMR hits MonTask during multiple R5 Rebuild with I/O.(SCGCQ01963365)
 - onfi_status not properly clearing SCAP_NOT_PRESENT state(SCGCQ01963729)
 - MR7.9-9480-8i8E:MonTask:line 151 in file fw\raid\utils.c rst=1while pull out a drive During Reconstuction from R1 to R6 & OCR(SCGCQ01965093)
 -	(SCGCQ01966636)
 - MR7.9 Alpha:Observed 8% to 50% drops in SW/SR for all IO sizes(SCGCQ01966683)
 - Ventura: SAS/SATA Drives behind passive backplane are not detected.(SCGCQ01969797)
 - The OTP page number for SLC Format was not getting saved in NVRAM(SCGCQ01969842)
 - Aero A0 Exposure: Firmware update is not allowed in JBOD personality	(SCGCQ01970010)
 - Back out change for: SES command to clear the CRIT or NON-CRIT bits doesn't clear the same under Enclosure Status diagnostic page(SCGCQ01970742)
 - Aero UTP : controller is not getting an EID assigned when running in MCTP OOB mode(SCGCQ01975573)
 - ModeSelect with ATO field will only be sent to the drive if ModeSense from the drive says the field is changeable.(SCGCQ01979538)
 - Mode Page change attempted on pages unsupported by SAT spec(SCGCQ01980228)
 - Fatal firmware error condition hit several times during overnight single glitch script(SCGCQ01985000)
 - Fix the PCie Host address space hardcoding for NVMe drives(SCGCQ01985216)
 - Getting invalid value selecting Manage controller mode in HII(SCGCQ01985983)
 - Cache Flush Interval can be changed on iMR Controllers.(SCGCQ01988420)
 - FW reports "Disk test cannot start. No qualifying disks found" during the diagnostics test with multiple drives present(SCGCQ01990513)
 - Toggle smallarm reports SOF PL as bad(SCGCQ01990539)
 - PL vSES: Number of slots for virtual SES is incorrect in StorCLI(SCGCQ01991774)
 - Spanky Memory Test failed to run	(SCGCQ01994851)
 - MegaRAID Event Log discards old Event Log across OCRs.(SCGCQ01996044)
 - Refresh Flash FS issue resulting on failed offload(SCGCQ02002626)
 - Assertion failure in fw\ddf\ddfConfig.c at line 5913: !LdIsEpd(ld(SCGCQ02005509)
 - Aero- Reinsert the same EPD Data Drive caused UG drive leading to data lost in JBOD mode(SCGCQ02008203)
 - change the Max Data Transfer Length to 1MB for Ventura(SCGCQ02008475)
 - Enable connector name checking for each phy(SCGCQ02012210)
 - Skip printing uncorrectable ecc errors while reading filesystem(SCGCQ02013637)
 - On demand snapdump not capturing PL logs	(SCGCQ02015618)
 - MR7.10 Aero Si: Assert Occurs When Migration Completes & VD Goes Missing; I/Os Stop on All VDs(SCGCQ02015773)
 - FW does not do secure boot authentication on HIIA/HIIM during download operation	(SCGCQ02015793)
 - Aero - FW returned "can't allocate sufficient mem" when trying to update Intel NVMe drive(SCGCQ02015867)
 - Address repetitive message being printed to the UART	(SCGCQ02016215)
 - When drive is pulled keep last valid slot number in Events Generated. This was introduced with changesets SCGCQ01520443 and SCGCQ01584278(SCGCQ02017502)
 - bad devH used in backend LMID causing bad devID to be used to index dmIoCtx(SCGCQ02017674)
 - AERO: Most IOs dropped in first OCR when system config is in EPD Maxconfig multipath(SCGCQ02018712)
 - A drive set as EPD in previous boot can became emergency HSP while booting	(SCGCQ02022786)
 - NVCache State is reported as faulty when there is an pending learn(SCGCQ02022949)
 - Fix Static Analysis Tool reported defect 18501 in Aero Project(SCGCQ02030076)
 - Fix Static Analysis Tool reported defect(SCGCQ02030079)
 - Fix Static Tool Analysis reported defect # 21985 in Aero Project(SCGCQ02030102)
 - Coverity Uninitialized scalar variable(SCGCQ02030127)
 - Wrong size of argument passed as length to function(SCGCQ02030138)
 - Wrong size of argument passed as length to function(SCGCQ02030142)
 - Fix Static Tool Analysis reported defect # 20641 in Aero Project(SCGCQ02030151)
 - Correct out-of-bounds read found by coverity checker(SCGCQ02030159)
 - Move pointer validation(SCGCQ02030164)
 - Fix Static Tool Analysis reported defect # 10096 in Aero Project(SCGCQ02030166)
 - Aero UTP: "Configuration command could not be committed to disk, please retry"(SCGCQ02031305)
 - Connect Tape device not showing details correctly(SCGCQ02031351)
 - Incorrect SAS address in the timedout event(SCGCQ02031494)
 - Enable supportOOBByteOffSetGet in Controller Info(SCGCQ02034980)
 - Close the previous Snap-dump When the Exception is Generated if there are any open snap-dumps.(SCGCQ02037323)
 - Able to set PR maxconcurrentpd as 0 for MR or iMR Ventura via Storcli(SCGCQ02040519)
 - Cocveirty: CID 22136 (#1 of 1): Uninitialized pointer read (UNINIT) 2. uninit_use_in_call: Using uninitialized value pMptReply(SCGCQ02042956)
 - HII menu software was expecting current profile and other compatible profiles to be returned(SCGCQ02043626)
 - Coverity: CID 22134 (#1 of 1): Explicit null dereferenced (FORWARD_NULL)dereference: Incrementing null pointer ptrPrpList.	(SCGCQ02043963)
 - Controller hang when MR is passthrough to the VM(SCGCQ02044166)
 - Change default NVDATA setting to enable spindown only for SATA SSD.(SCGCQ02044267)
 - Additional fixes for print statements(SCGCQ02045227)
 - Aero A0_Pull/Push Cable caused an assertion with Multipath EPd+R0's(SCGCQ02048037)
 - Further fixes for print statements(SCGCQ02051192)
 - Avoid sending intercore request to copy core1 holding buffer every 10ms(SCGCQ02053681
 - PL fault 0x6001 observed with heavy IOs to some NVME drives with Async events(SCGCQ02057418)
 - Performance drops of 5-20% observed in lower IO size and higher QD's for SR/SW DC/EC- SAS,SATA HDD(SCGCQ02059845)
 - Aero UTP: On-demand snapdump lost when created before learn cycle on new SCAP(SCGCQ02059851)
 - Fail an attempt to add a smaller sized disk as a dedicated hot spare drive for VD(s(SCGCQ02061714)
 - reboot needed message is not displayed(SCGCQ02061754)
 - Ventura: MR7.10: No NVME drives detection on UBM Ux2 with latest package build 2186 (previous package detects drives(SCGCQ02081778)
 - MR 7.10: Generate and get snapdump on Cavium ARM server resulted in firmware exception(SCGCQ02082059)
 - importation of incomplete foreign config cause MR FW crash(SCGCQ02085950)
 - Controller crash during foreign import scan(SCGCQ02101697)
 - Host utils data for Download tty does not match with FW tty buffer dump(SCGCQ02123014)
 - Fix build error due to SCGCQ02128295(SCGCQ02131859)
 - [RHEL 8.1] system will hang with SME enable(SCGCQ02184712)
 - Fix stream build error "undefine symbol onfiClearNvramParam"(SCGCQ01534565)
 - changes for cache offload fpga(SCGCQ01559701)
 - compile errors(SCGCQ01564758)
 - Fix colFmcMultiplaneEnable(SCGCQ01628968)
 - Aero COL FPGA: temporary change to always return unsuccessful from read retry till proper code is in place(SCGCQ01698449)
 - Fix unaligned memory access(SCGCQ01714662)
 - fix compile errors associated to rebase(SCGCQ01761483)
 - NVSRAM loss recovery for COL - bug fixes(SCGCQ01765359)
 - Update LSISAS3916.xsd with latest changes and correct signature(SCGCQ01839918)
 - Controller Exception Called for Processor Core = 0 when pinned cached is present(SCGCQ01855070)
 - Aero PA0.7: Data Abort exception detected when Max Resets per boot cycle reached!!(SCGCQ01855357)
 - Aero PA0.7: Aero Vision FW reports chip reset when SysLite is expected upon a warm reboot from OS as long as SCaP is present(SCGCQ01877017)
 - Aero PA0.7- Data corruption found on degraded R1 VD after OCR.(SCGCQ01880866)
 - Aero PA0.7: Talladega / Vision - Assertion failure in fw\cpu\arm\exceptions.c during reboot after PKG1679 FW Update(SCGCQ01885746)
 - Debug output contains multiple copies of the same information(SCGCQ01899293)
 - Revert CQ#SCGCQ01838839 changes in Aero Stream(SCGCQ01902123)
 - Remove/re-insert drive from Elrond enclosure with Ex1 result in amber lights turn on(SCGCQ01903940)
 - pl UBM: Locate LED cannot be turned off after diag reset for few drives on Ex1 Elrond(SCGCQ01905070)
 - HSP do not spin down when BGI is running	(SCGCQ01917771)
 - Fix xsd files for Ventura(SCGCQ01918580)
 - Kill Adapter/OCR and Controller Hotplug detected during continuous Snapdump generation.(SCGCQ01923648)
 - Updating link speed from PCIe IO Unit page 0.(SCGCQ01924416)
 - Correct disableSESMgmt and SecureLED support while under autoconfig R0 mode.(SCGCQ01935021)
 - PL: Multipath: Failure to Enumerate Devices in Windows After Cable Pull/Push(SCGCQ01936773)
 - Aero: backend PCIe: Atlas support is disabled by default(SCGCQ01937069)
 - pl: backend PCIe: disable managed switch support(SCGCQ01940694)
 - Aero: CBB-Only in FLASH will fault due to external synchronous abort(SCGCQ01942768)
 - pl: backend PCIe: switch attached NVMe device enumeration failed(SCGCQ01944149)
 - megamon mem command results in data abort(SCGCQ01945011)
 - Fix memset in colReconditionDevice(SCGCQ01949955)
 - AI for NVME pass through.(SCGCQ01951370)
 - FW shows key update pending while utilities do not(SCGCQ01956335)
 - Read retry takes a long time to complete	(SCGCQ01956439)
 - Ventura: SES Page 0Ah element descriptors of controller PHYs connected to a SMP target are marked as valid(SCGCQ01957185)
 - Snap-Dump not generated during early boot because snap-dump memory is not initialized.(SCGCQ01958249)
 - Fix colDbgEraseFsBlocks to erase correct blocks(SCGCQ01969794)
 - FW hangs at "C0: mapVirtualMemory:" after a power cycle during IO(SCGCQ01971637)
 - H345 fails to create/delete/edit partitions in Windows on JBOD drive.(SCGCQ01978750)
 - Mode Page setting for Control page failed to observe NVMe translation restriction(SCGCQ01979406)
 - MR_7.9: Snapdump is not triggered in "dmaErrorIsr" Error path.(SCGCQ01989936)
 - Remove CSET SCGCQ01961503(SCGCQ01990091)
 - Cleanup Chip Builds(SCGCQ01991522)
 -(SCGCQ01991554) 
 - immediate error return from PL not always handled properly(SCGCQ01996107)
 - Aero : CacheHeader Mismatch, Cache being discarded during pinned cache learn test.(SCGCQ01998397)
 - Issues with reading the metadata(SCGCQ01998549)
 - PL: SAS link up and drive discovery is delayed(SCGCQ02005349)
 - Dev defect to check-in a missing change for an original change set check-in.(SCGCQ02006880)
 - Controller no longer accessible after poweroff and poweron VMware virtual machine (VMware passthrough enabled(SCGCQ02013448)
 - Remove OEM checks in a few OEM PRs which are implemented generically(SCGCQ02020017)
 - Aero A0: Montask Fatal firmware error: Line 152 in fw\raid\utils.c during IO to large topology(SCGCQ02023759)
 - BST Failure(SCGCQ02028652)
 - Supercap status shown as missing as Config page reads appear to be failing(SCGCQ02029916)
 - Fix Static Analysis Tool reported defect 18458 in Aero Project(SCGCQ02030072)
 - Fix Static Analysis Tool reported defect 22009 in Aero Project(SCGCQ02030082)
 - Coverity uninitialized scalar variable(SCGCQ02030149)
 - Fix unexpected fall through in switch statement(SCGCQ02030153)
 - Fixing static analysis tool reported issue(SCGCQ02030160)
 - Add checking for bad return codes(SCGCQ02030161)
 - Should NOT allow to migrate R0 to R6 with 3 PDs since Aero no longer support 3 PDs R6(SCGCQ02032210)
 - 512B drive gets assigned as DHSP to 4K DG.(SCGCQ02034375)
 - Aero A0 UTP: Assertion failure(SCGCQ02035865)
 - Bad PHYs Reported and Slow Enclosure Initialization(SCGCQ02044157)
 - Revert change from SCGCQ02037299 for Ventura(SCGCQ02046436)
 - Add back the class code in the PCE setting in XSD(SCGCQ02047323)
 - Adding additional descriptor for aligning the data data transfer on page and plane count(SCGCQ02047335)
 - Declare dumpMemoryBytes function in colSystem.h(SCGCQ02047376)
 - Dev Defect - System not stable with NVME enabled.(SCGCQ02048189)
 - Storcli is not showing foreign configs using Ventura controllers if user has SED drive which is in foreign.(SCGCQ02060808)
 - Dev Defect - Re-enable NVMe for a specific OEM.(SCGCQ02064349)
 - Vses Device Type is displayed as Enclosure for iMR Board	(SCGCQ02080574)
 - MR_7.9_Huawei:Data Abort exception observed while running target reset on NVMe JBOD with PD FW flash(SCGCQ02081414)
 - FW crash - MonTask: line 152 in file fw\raid\utils.c rst=0 while doing FW downgrade in iMR card(SCGCQ02102820)
 - Performance drop in few corner cases(SCGCQ02112423)
 - IOPS performance number were lower compared to prior releases(SCGCQ02132080)
 - iMR- MCTP FW flash leads to Data Abort exception(SCGCQ02169770)
 - Fix is to set clear-configuration-flag properly if drives are spun-down(SCGCQ02178378)
 - Add new header file to fix compilation Issue in COL Int Stream(SCGCQ01582409)
 - Fixed Fix Wait for Bit set function in ONFI(SCGCQ01602913)
 - Fix bug in routine which returns command descriptor address register.(SCGCQ01630363)
 - Removing flashRegionToggleReq hack in colPrepareForOffloadEvent(SCGCQ01684790)
 - Aero COL FPGA: fix block number for read eye training(SCGCQ01714751)
 - Fix read/write cache in async mode(SCGCQ01747636)
 - More than 2 asserts can be triggered between T5 and T20 while booting.(SCGCQ01865886)
 - Fix compilation in col_common_pa_Int stream.(SCGCQ01869912)
 - Turn on supportEPDWithAutoConfigOff flag for Ventura Raid in Aero code.(SCGCQ01871826)
 - VenturaB0: SAS/SATA drives are not getting discovered with NVMe disabled firmware on both Crusader 9400-16iB0 and 9405W-16iB0(SCGCQ01876271)
 - Fix issues found in new function on IO path (2)(SCGCQ01884166)
 - Ventura MSS: VRef training failures on Marlin/Pocono boards.(SCGCQ01891340)
 - fw hit exception after creating VDs and "debugOcr reset 0 0"(SCGCQ01915749)
 - sense data may not match error LBA for NVMe I/O splitted into multiple MPT frames(SCGCQ01924437)
 - SAS BST Failure(SCGCQ01926295)
 - incorrect struct size in PL phy enable/disable call(SCGCQ01941812)
 - HW Workaround:Settings Change for Requested Tx Presets for PCIe Gen3 and Gen4 rates(SCGCQ01949931)
 - Remove changes ported from defect SCGCQ01937998.	(SCGCQ01950909)
 - Controller asserted after issuing ONFI BBLIST RECLAIMALL cmd to clear full BBLIST; 0x80 entries.(SCGCQ01952141)
 - Fix colNvramRecover to bring back check for SLC states(SCGCQ01964540)
 - while IO power down then power up system for auto start io found fw hit a false assertion failure. iMR only.(SCGCQ01966760)
 - Aero UTP : breaking into MegaRAID FW debugger can take long time	(SCGCQ01973382)
 - Aero A0 UTP: Creation of multiple VDs causes data abort (possibly after hot add of drives(SCGCQ01979476)
 - Aero UTP: VDs either created or imported are in WT and doesn't change to WB(SCGCQ01983399)
 - Toggle smallarm reports SOF PL as bad(SCGCQ01986407)
 - Aero A0 UTP: bios post complains of exceeding the maximum allowable limit of 2 enclosures (3 enclosures attached(SCGCQ01990665)
 - 7.9:VSES number of slots are incorrect in StorCLI(SCGCQ01991770)
 - All profiles not being enumerated in response to MR_DCMD_CTRL_PROFILE_LIST_GET(SCGCQ01992464)
 - PI disabled scenarios(SCGCQ01995262)
 - FW hit the assertion when user tries to change the PD state from failed to online state in IMR card(SCGCQ01997813)
 - Windows shutdown issue on the 9560-8i board in specific system(SCGCQ02022795)
 - Aero A0 UTP - Megamon TTY port locked after Pl fault with OCR disabled	(SCGCQ02023854)
 - Aero UTP: VSAN test fails on EVT Aero 16i boards when ctrl FW is flashed through OOB (PCIe(SCGCQ02030030)
 - Don't update memory twice for a loop variable(SCGCQ02030071)
 - Fix Static Analysis Tool reported defect 18497 in Aero Project(SCGCQ02030074)
 - Aero UTP: cacheoffload : snapdump lost during power cycle after disabled controller passthrough(SCGCQ02031400)
 - FW hits exception in > 240PDs maxconfig, but user can't get into FW dbg	(SCGCQ02032498)
 - OFU does not occur when flashing an image with a Secure Boot key change	(SCGCQ02035580)
 - EPDs created in jbob personality is lost after reboot(SCGCQ02041664)
 - More fixes for print statements(SCGCQ02041971)
 - coverity defect: CID 22138 (#1 of 1(SCGCQ02042959)
 - Do not show unmapCapableForLD as TRUE if unmap feature is disabled.(SCGCQ02053381)
 - Junk Values Appears in OnDemand snapDump when collected for iMR Board(SCGCQ02085496)
 - issues with reading flash file system(SCGCQ01665418)
 - Add defines for Flash phy and controller base address in colmain.h(SCGCQ01765003)
 - Aero PA0.7 - ProfilePersonalityChangeRequest: Invalid Personality Change detected when request from Storcli(SCGCQ01866860)
 - Wingman - After a COL test, the controller hangs on a reboot.(SCGCQ01891833)
 - After importing a VD Consistency Check starts instead of Background Initialization.(SCGCQ01900886)
 - pl: backend PCIe: unsupported completion timeout capabilities don't cause init failure(SCGCQ01906471)
 - MR 7.8 - OCR snapdump not getting generated(SCGCQ01942123)
 - 9460-8i:"Other Error Count" of drives increase when running dd test(SCGCQ01943742)
 - Fix junk chars on uart when all EOF are erased(SCGCQ01957522)
 - MR 7.8 Package fails to spin-up multiple SAS SPL-2 Power Control capable drives(SCGCQ01963504)
 - Can not migrate R0 to R6 by adding 3 more PDs(SCGCQ02039842)
 - Kill Adapter if PD FW download is run in continous loop(SCGCQ02059825)
 - PFA condition was not detected(SCGCQ02069532)
 - Assertion failure in fw\hw\pce\fusion.c at line 744 seen while flashing the FW and VD creation/deletion(SCGCQ02105135)
 - Renamed configFileSystemPrimary field in COL_FLASH_CHIP_SELECT to PtrConfigFileSystemPrimary in col_common code(SCGCQ01620922)
 - COL ONFI Single Image support was broken with onfiValidateCSCount changes(SCGCQ01675779)
 - Aero Compilation Error(SCGCQ01841060)
 - MR to iMR Foreign import fails with mem alloc failure(SCGCQ02052312)
 - Cannot get onDemand snapdump after system and ctlr hang manual recovery(SCGCQ02112984)
 - Unnecessary prints related to TFM(SCGCQ01956409)
 - The debug command 'col startcolrestore' reportig restore failure after offload(SCGCQ01958521)
 - Fixed the display in ar debug function for MR_LD_BITMAP so correct numPd can be displayed(SCGCQ01963368)
 - Set BB table refresh flag after erasing bb table block(SCGCQ01971808)
 - iMR Snapdump remove intermediate buffer size restriction.(SCGCQ02064738)
 - Increase the sram heap for iMR(SCGCQ02083966)
 - Slave dma cmd times out while reading data(SCGCQ01945003)
 - MR- 240VD Foreign import fails though the max limit is not hit.(SCGCQ02090769)
 - SL shows successful message if user set Max PDs on which PR can be run concurrently for any numbers(SCGCQ02102597)
 - SATA: IO Timeouts with Read/Write and Non-Automated IO(SCGCQ02150508 port of SCGCQ01958700)
 - Swap Bit Value in VSES Page 0x2 is incorrect(SCGCQ02103256 port of SCGCQ02081299)
 - VSES : Incorrect Array Device Element Status After Diag Reset(SCGCQ02103212 port of SCGCQ02085530)
 - pl: backend PCIe: ED06 fault	(SCGCQ02101515 port of SCGCQ02094366)
 - To have separate transmit and receive I2C buffers for the back plane management module(SCGCQ02063705 port of SCGCQ01979141)
 - PL: SAS Drives Take a Long Time to Link Up and Are Not Discovered Correctly(SCGCQ01999187 port of SCGCQ01973566)
 - PL vSES: Number of slots for virtual SES is incorrect in StorCLI	(SCGCQ01995099 port of SCGCQ01991774)
 - Data Abort Exception observed while running reboot test with a bad drive.(SCGCQ01995097 port of SCGCQ01985789)
 - PL : Task management timeout is observed if the task management type is invalid(SCGCQ01980454 port of SCGCQ01969521)
 - Customer specific back plane not detected in the latest code phase(SCGCQ01972786 port of SCGCQ01961997)
 - (SATA Only) Firmware may fault (faultcode 0xD102) If task management is sent while SSU command is being translated to SATA drive.(SCGCQ01963909 port of SCGCQ01945583)
 - (vSES) Injecting error on I2C channel of one connector module will cause LED of another connector module to not work.(SCGCQ01961505 port of SCGCQ01955094)
 - Ventura: Direct attached NVMe may not be detected in a mixed UBM backplane config(SCGCQ01956223 port of SCGCQ01951369)
 - Ventura: NVMe devices attached to I2C backplane with no BP mgmt. device may not be detected by the HBA(SCGCQ01955451 port of SCGCQ01933117)
 - PL SATL : TM aborted inquiry command is failed with check condition(SCGCQ01955070 port of SCGCQ01944673)
 - PL: SSP Open Address frame uses wrong Destination SAS Address(SCGCQ01954788 port of SCGCQ01940668)
 - (NVME) Fw Fault (faultcode 0xEC56) hit while performing system reboot test with NVMe drives attached.(SCGCQ01944380 port of SCGCQ01932728)
 - (NVME) Fw Fault (faultcode 0xEC56) hit while performing system reboot test with NVMe drives attached.(SCGCQ01944367 port of SCGCQ01932728)
 -(SCGCQ01935009 port of SCGCQ01930597)
 - vSES SES Page 0Ah may report same SAS address for two elements during hot remove/add of NVMe devices(SCGCQ01934941 port of SCGCQ01934145)
 - MPI 3.0: define for PLBP Signature is incorrect.(SCGCQ01933116 port of SCGCQ01933103)
 - PL Fault 0x6001 occurred while running IOs + Task Management requests(SCGCQ01931043 port of SCGCQ01850755)
 - IO's can time-out after controller receives an unconfirmed response from a drive(SCGCQ01926166 port of SCGCQ01878174)
 - Add workaround for SATA drive not complaint with ACS-3(SCGCQ01924984 port of SCGCQ01922154)
 - MR7.8: CTRL does not detect drives with SAS3.5CtrlFw_Ventura_Ph_9.0 08.250.09.00 and 10 as well(SCGCQ01917864 port of SCGCQ01914192)
 - Ventura: IOC init may fail with Host Page Size Invalid LogInfo on backend PCIe disabled FW(SCGCQ01917857 port of SCGCQ01916779)
 - pl: backend PCIe: bug when setting up direct attached PL structures(SCGCQ01917839 port of SCGCQ01915755)
 - pl: backend PCIe: link fails to come up after a surprise down(SCGCQ01915671 port of SCGCQ01886012)
 - pl: backend PCIe: unsupported completion timeout capabilities don't cause init failure(SCGCQ01907104 port of SCGCQ01906471)
 - pl UBM: Ux4 drives not discovered in Polling Mode with HFCx16 and x8(SCGCQ01906082 port of SCGCQ01896578)
 - Debug output contains multiple copies of the same information(SCGCQ01904001 port of SCGCQ01899293)
 - pl: NVMe: E40A fault if WRPROTECT or RDPROTECT is nonzero(SCGCQ01903727 port of SCGCQ01892105)
 - Ventura: OEM SW Enclosure Amber LED stays on after reboot(SCGCQ01900846 port of SCGCQ01898852)
 - Ventura: NVMe I2C Backplane Detection fails on HBA connectors C2/C3 resulting in Slots not responding to LED update(SCGCQ01900839 port of SCGCQ01886810)
 - Ventura: Fault 0x2805 encounted if one configures NVME and AutoPortEnable at the same time(SCGCQ01896498 port of SCGCQ01868375)
 - Incorrect vSES Data for Page 0x02 After Storcli Start & Stop Locate Operations for certain NVME Backplanes.(SCGCQ01893315 port of SCGCQ01671177)
 - pl UBM SFF-TA-1005: Locate LED cannot be turned off after diag reset(SCGCQ01891218 port of SCGCQ01884070)
 - PL:(SATA Only) SCSI unmap command sent to SATA-SSD which supports Send/Receive FPDMA command lead to controller fault 0xD101(SCGCQ01890861 port of SCGCQ01816525)
 - pl SFF-TA-1005: All Ux4 drives are not discovered in x8 or x16 HFC mode while hot-plugging(SCGCQ01887446 port of SCGCQ01877041)
 - VenturaB0: SAS/SATA drives are not getting discovered with NVMe disabled firmware on both Crusader 9400-16iB0 and 9405W-16iB0(SCGCQ01878142 port of SCGCQ01876271)
 - 0x6004 Fault running TM only test(SCGCQ01876864 port of SCGCQ01858982)
 - pl: Locate LED on SFF-TA-1005 Ux4 backplanes configured in x16 or x8 HFC emulation mode is not activated by storcli command(SCGCQ01873143 port of SCGCQ01866800)
 - pl: SAS/SATA devices not discovered with partial backplane configuration(SCGCQ01872005 port of SCGCQ01870842)
 - [Ventura][PL] Applications trying to update NVMe device Firmware with Mode E fails(SCGCQ01868163 port of SCGCQ01624790)
 - OFU Failed on FW Download(SCGCQ01790850 port of SCGCQ01788985)
 - Observed Data TLB exception when Sanitize with Block Erase service action is issued on a SATA SSD(SCGCQ01729541 port of SCGCQ01617939)
 - FPGA Support	(SCGCQ01557005 port of SCGCQ01526235)
 - Debug API to display COL blocks(SCGCQ01761582 port ofSCGCQ01713679 )
 - Increase DDR size on FPGA by 256MB(SCGCQ01762262 port of SCGCQ01757985)
 -	(SCGCQ01763319 port of SCGCQ01721508)
 - Verify that the Statistics from 57 Pages of NAND Parameters can be read(SCGCQ01778145 port of SCGCQ01735503)
 - Avenger: ONFI Flash commands not working in SDR/Async mode(SCGCQ01858376 port of SCGCQ01842564)
 - Disable OOB communication via I2C(SCGCQ01870883 port of SCGCQ01369359)
 - Request to not reset the Idle Timers	(SCGCQ01870884 port of SCGCQ01274044)
 - Sotrlci Hide/Unhide command output display incorrect status(SCGCQ01876281 port of SCGCQ01861900)
 - PR State Machine Clean up during Patrol Read/Check Consistency Conflicts	(SCGCQ01878302 port of SCGCQ01260431)
 - The security key lifecycle management for EKMS(SCGCQ01878354 port of SCGCQ01155304)
 - Adding the function that changing flag of full initialize completion(SCGCQ01878369 port of SCGCQ01134165)
 - Method for determining bad ONFI flash via Storcli & SNMP trap upon NAND flash failure for Aspen and Vail (Invader and Intrude(SCGCQ01878415 port of SCGCQ01219862)
 - WG: Instance Validation issues pertaining to Energy pack (GET)(SCGCQ01878450 port of SCGCQ01139341)
 - Set PF bit in Send Diagnostics command(SCGCQ01880855 port of SCGCQ01872901)
 - Set temperature polling interval to 10 secs for Direct attached drives.(SCGCQ01880857 port of SCGCQ01878220)
 - Controller can not correctly detected smart error SATAA HDD.(SCGCQ01881151 port of SCGCQ01506289)
 - Unnecessary prints logging while issuing DCDB commands(SCGCQ01882469 port of SCGCQ01274681)
 - Change the reserve field in structure mode param to follow spc4 spec(SCGCQ01884169 port of SCGCQ01816426)
 - Do not forcefully change user changeable AutoEnhancedImport property(SCGCQ01889451 port of SCGCQ01886136)
 - 7.5 R1 performance change request.(SCGCQ01896639 port of SCGCQ01614688)
 - Avenger FPGA: UART hangs if wrong COL parameters sent(SCGCQ01897694 port of SCGCQ01891214)
 - Target ID enumeration for fan-out enclosure topology	(SCGCQ01914071 port of SCGCQ01906168)
 - Remove BAIL OUT message for successful partial vd creation command(SCGCQ01915624 port of SCGCQ01887298)
 - ONFI BBL reassignment: COL loop on power glitch during initial COL.(SCGCQ01915640 port of SCGCQ01915345)
 - Firmware Test API returns incorrectly that hardware is armed for offload, when supercap is bad.(SCGCQ01920227 port of SCGCQ00853020)
 - PR is being run on ePDs(SCGCQ01922373 port of SCGCQ01761270)
 - CCR ResetStatus User bits need to change in Aero(SCGCQ01929653 port of SCGCQ01602701)
 - When replacing SATA drive with a new SATA drive predictive fail and other error counters are not cleared(SCGCQ01930659 port of SCGCQ01911292)
 - Avoid issuing data loss boot message in R1 write through volumes.(SCGCQ01933669 port of SCGCQ01714192)
 - support to query multibit ecc error by storeliboob(SCGCQ01933744 port of SCGCQ01799177)
 - HDET: Support smp passthrough in storlib and storeliboob(SCGCQ01933785 port of SCGCQ01799154)
 - Wingman - After a COL test, the controller hangs on a reboot.(SCGCQ01934966 port of SCGCQ01891833)
 - Support IML logging feature for Shenandoah(SCGCQ01934971 port of SCGCQ01788447)
 - Wingman - After a COL test, the controller hangs on a reboot.(SCGCQ01935046 port of SCGCQ01891833)
 - MR7.8 OEM: WT VD created on attempt to create WB VD(SCGCQ01936868 port of SCGCQ01916098)
 - MR7.8 OEM: WT VD created on attempt to create WB VD(SCGCQ01936917 port of SCGCQ01916098)
 - undo previous fix; previous fix introduces undesirable side effects(SCGCQ01937071 port of SCGCQ01932051)
 - Cannot be done initialize even if execute Full Initialize by using StorCli(SCGCQ01944953 port of SCGCQ01938067)
 - Changes to support NVME X2 BP.(SCGCQ01948646 port of SCGCQ01582910)
 - Read correct Back plane GPIOs for Back plane type detection(SCGCQ01951032 port of SCGCQ01932040)
 - BGI improvements for cryptographically erasable drives(SCGCQ01957618 port of SCGCQ00757727)
 - During drive spin up, drives come up as 0 bytes(SCGCQ01957642 port of SCGCQ01944951)
 - During drive spin up, drives come up as 0 bytes(SCGCQ01961977 port of SCGCQ01944951)
 -	(SCGCQ01962702 port of SCGCQ01956442)
 - Add downgrade check in firmware to avoid flashing older firmware which do not support Winbond 16MB Flash part(SCGCQ01962766 port of SCGCQ01962764)
 - DDR tuning parameters based on subOEM ID(SCGCQ01971332 port of SCGCQ01964424)
 -	(SCGCQ01971828 port of SCGCQ01966080)
 - dummy function for cache offload(SCGCQ01978410 port of SCGCQ01971170)
 - OEM Specific:DM_Cfg_UpdateGPIOFromMfgPage6 and GPIOinit Cleanup(SCGCQ01978564 port of SCGCQ01943764)
 - Controller asserted after issuing ONFI BBLIST RECLAIMALL cmd to clear full BBLIST; 0x80 entries.(SCGCQ01978568 port of SCGCQ01952141)
 - Heavy MFI based LD IO writes during POST causing WJ entries exhaust on iMR and FW asserting(SCGCQ01979536 port of SCGCQ01930815)
 - MR7.7: Missing diagnostic failed in event log when PD state goes ONLINE to SHIELD and then to FAILED(SCGCQ01979704 port of SCGCQ01927550)
 - SMP pass through not working when the “PD 0” is BAD drive(SCGCQ01979738 port of SCGCQ01945602)
 - Avenger COL: Prevent arming of COL if offload not sustainable(SCGCQ01980191 port of SCGCQ01978562)
 - Disable Opal Support for all drive types on Perc Controllers.(SCGCQ01982370 port of SCGCQ01943008)
 - PERC10.4:ONFI: BBLIST RECLAIMALL does not purge factory bad blocks(SCGCQ01983560 port of SCGCQ01978319)
 - Able to convert only 30 PD's as UG on iMR controller(SCGCQ01985915 port of SCGCQ01077558)
 -	(SCGCQ01986353 port of SCGCQ01957306)
 - After importing a VD with pinned cache, a Consistency Check starts instead of Background Initialization.(SCGCQ01990048 port of SCGCQ01973185)
 - Factory Verification System (FVS) appliance(SCGCQ01992408 port of SCGCQ01958192)
 - Aero UTP: Firmware hung during new drives inserted with autoconfig=r0(SCGCQ01992714 port of SCGCQ01982809)
 - Kill adapter observed while running target reset on JBOD WB(SCGCQ01995387 port of SCGCQ01789188)
 - After OCR controller returns error with ekms cmds(SCGCQ01996052 port of SCGCQ01987170)
 - Snapdump Enhancement : Addition of symbol table to snapdump(SCGCQ02003511 port of SCGCQ01948001)
 - Firmware allows to create lower size Dedicated spare compared with the size of the drive part of the Drive Group(SCGCQ02006215 port of SCGCQ01981279)
 - iMR: KillAdapter when running IOs and when there is a medium error on drive.(SCGCQ02012564 port of SCGCQ01996272)
 - Unexpected sense when spinning down SAS drives during shutdown.(SCGCQ02015147 port of SCGCQ01999239)
 - Unable to simulate bad flash with LB/LBP on Plumas server(SCGCQ02020100 port of SCGCQ01357295)
 - Possibility of data loss due to abrupt/asynchronous warm reset(SCGCQ02023870 port of SCGCQ01985158)
 - When drive is pulled keep last valid slot number in Events Generated. This was introduced with changesets SCGCQ01520443 and SCGCQ01584278(SCGCQ02030761 port of SCGCQ02017502)
 - Move OCM ECC error scrubbing logic to interrupt context(SCGCQ02030800 port of SCGCQ01970027)
 - Data Abort Exception on abrupt powerloss/reset when flushing events from NVRAM hold buffer to flash(SCGCQ02031404 port of SCGCQ01973389)
 - ESXi 6.7 does not see JBODs during install or in vSphere.(SCGCQ02034048 port of SCGCQ01994684)
 - Disable TransportReady In ICMR1(SCGCQ02034184 port of SCGCQ01828691)
 - ICMR1 With Storlibtest (OOB) TR can be enabled on VD's it should be disabled(SCGCQ02034237 port of SCGCQ01909345)
 - Aero- Hitting data integrity issue on R1 while running I/O across all RAID levels(SCGCQ02035842 port of SCGCQ02016614)
 - Rebuild PD's in R1 VD wrongly moved to failed state with heavy IOs running(SCGCQ02035885 port of SCGCQ01859482)
 - FW reports "Disk test cannot start. No qualifying disks found" during the diagnostics test with multiple drives present(SCGCQ02039584 port of SCGCQ01990513)
 - storcli/storeliboob report error of TFM nvcache(fw,tools	(SCGCQ02042413 port of SCGCQ01799185)
 - Avenger COL: Coverity CID 21499 uninitialized variable(SCGCQ02042728 port of SCGCQ02041531)
 - Erase operation is disabled for EPD.	(SCGCQ02043925 port of SCGCQ01937381)
 - Adjust 2nd COL descriptor to enforce an even number of Quanta Bytes(SCGCQ02045287 port of SCGCQ02031398)
 - iMR/CLI controller info reports "Support SystemPD = No" even though JBOD is supported(SCGCQ02046552 port of SCGCQ02042390)
 - Data abort if DevID of SAS PD is sent instead of NVMe PD for NVMe Passthrough(SCGCQ02048643 port of SCGCQ01915272)
 - 7.9:VSES number of slots are incorrect in StorCLI(SCGCQ02048962 port of SCGCQ01991770)
 - Host DCDB time out values are getting updated incorrectly(SCGCQ02049503 port of SCGCQ01986878)
 - For a specific OEM, in release 10.4, driver detected FW hang during I/O across all RAID levels with different background operations running(SCGCQ02051156 port of SCGCQ02008617)
 - All profiles not being enumerated in response to MR_DCMD_CTRL_PROFILE_LIST_GET(SCGCQ02053600 port of SCGCQ01992464)
 - After importing a VD with pinned cache, a Consistency Check starts instead of Background Initialization.(SCGCQ02057457 port of SCGCQ01973185)
 - 10-Slot Passive BP: System hung at "===> Requesting BIOS to initiate reboot/reset, please wait <==="	(SCGCQ02059568 port of SCGCQ02022810)
 - Cryptographic Erase operations are blocked for JBODs	(SCGCQ02065044 port of SCGCQ02010293)
 - Foreign status not shown on EKMS drive after runtime key exchange is done(SCGCQ02065045 port of SCGCQ02023636)
 - ModeSelect with ATO field will only be sent to the drive if ModeSense from the drive says the field is changeable.(SCGCQ02065600 port of SCGCQ01979538)
 - Copyback will fail with a secured VD following a rebuild from a DHS.	(SCGCQ02065795 port of SCGCQ02047361)
 - Unable to flash from 10.4 to 10.2 in eHBA mode.(SCGCQ02066765 port of SCGCQ02042797)
 - Max number of PDs for PatrolRead to run concurrently should be in range from 1 to MR controller's max configurable PDs(SCGCQ02078413 port of SCGCQ02008420)
 - FW PKG 2115 getting hung and NAKing I2C traffic(SCGCQ02080243 port of SCGCQ02053377)
 - EKMS unable to unlock drive - returns key from escrow is invalid	(SCGCQ02080244 port of SCGCQ02063970)
 - Copyback failed on data drive when failed drive inserted back on EKMS encrypted VD(SCGCQ02080245 port of SCGCQ02077226)
 - The SUT can’t boot to OS after 159 loops AC cycle and check the Raid 930-16i 8G(SCGCQ02081097 port of SCGCQ01788479)
 - Assertion failure in fw\mros\mem.c at line 812: on sending STP passthru from OOB SLT on SATA drive(SCGCQ02081204 port of SCGCQ02050864)
 - HII menu software was expecting current profile and other compatible profiles to be returned(SCGCQ02081206 port of SCGCQ02043626)
 - Secure Erase operations are blocked for JBODs on iMR(SCGCQ02081442 port of SCGCQ01999048)
 - When discarding a pinned cache and rebooting, discard the cache message observed(SCGCQ02081443 port of SCGCQ01973033)
 - Sort IOPATH Data Structure Memory(SCGCQ02081781 port of SCGCQ01962789)
 - EKMS unable to unlock drive - returns key from escrow is invalid(SCGCQ02082110 port of SCGCQ02063970)
 - Some Configured drives may change to JBOD and Unconfigure Good after Set JBOD=on and reboot(SCGCQ02082515 port of SCGCQ02080101)
 - FW not logging events if it doesn't get all the keys.(SCGCQ02083613 port of SCGCQ02079256)
 - Adapter reset due to an exception(SCGCQ02084115 port of SCGCQ02062791)
 - iMR: VSAN disk failed and unexpected timeout and phy link errors found(SCGCQ02084118 port of SCGCQ02048151)
 - R0 LD become JBOD after pull and push after auto import(SCGCQ02086533 port of SCGCQ02015452)
 - Assertion failure in fw\raid\mpthostcmd.c at line 2019 observed while create/delete VD's with OOB stress test(SCGCQ02097940 port of SCGCQ02072363)
 - Fix variable declaration	(SCGCQ02101096 port of SCGCQ02101077)
 - Data corruption found while running I/O's on 5 drive R5 vd with rebuild walk(SCGCQ02101909 port of SCGCQ02092758)
 - Boot agent status not getting updated in all cases(SCGCQ02103966 port of SCGCQ02101577)
 - Corresponding MR code changes for RMC stack overflow checking(SCGCQ02105879 port of SCGCQ02076547)
 - EKMS 10.3: Reboot loop results in OS getting corrupted i,e 0xC000000E (Required Device is Inaccessible(SCGCQ02106412 port of SCGCQ02080146)
 - OCR breaks EKMS	(SCGCQ02106419 port of SCGCQ02049263)
 - Cache Offload BST : Add support to upload termlog via DCMD(SCGCQ02106761 port of SCGCQ02102716)
 - sense data returned from out-of-band storlibtest is wrong(SCGCQ02112231 port of SCGCQ02050648)
 - CSCvn34219 - Fatal Firmware Error after several hours of host reboot loops(SCGCQ02113869 port of SCGCQ01966713)
 - Aero- Foreign Import failed while pinned_cache is present(SCGCQ02117317 port of SCGCQ02094870)
 - Kill Adapter if PD FW download is run in continous loop	(SCGCQ02117319 port of SCGCQ02059825)
 - Aero- OCR hit "Max Resets per boot cycle reached!!!" and failed to recover leading to all I/O crashed(SCGCQ02118157 port of SCGCQ02080408)
 - On iMR Adapter launching Virtual Disk Wizard to create VD leading to OS crash/hang(SCGCQ02118700 port of SCGCQ02118031)
 - OS shutdown hangs due to Flush cache DCMD not completed(SCGCQ02125434 port of SCGCQ02110329)
 - Host utils data for Download tty does not match with FW tty buffer dump.(SCGCQ02127253 port of SCGCQ02123014)
 - iMR: VSAN disk failed and unexpected timeout and phy link errors found(SCGCQ02127914 port of SCGCQ02048151)
 - SL shows successful message if user set Max PDs on which PR can be run concurrently for any number(SCGCQ02149905 port of SCGCQ02102597)
 - Incorrect SAS address in the timedout event(SCGCQ02150134 port of SCGCQ02031494)
 - Vses Device Type is displayed as Enclosure for iMR Board(SCGCQ02150638 port of SCGCQ02080574)
 - Host utils data for Download tty does not match with FW tty buffer dump.(SCGCQ02150840 port of SCGCQ02123014)
 - Able to set PR maxconcurrentpd as 0 for MR or iMR Ventura via Storcli(SCGCQ02150995 port of SCGCQ02040519)
 - Update next learn cycle schedule to only NVSRAM after TLC completion(SCGCQ02153759 port of SCGCQ02138680)
 - PFA LED is not on when a PFA drive is attached directly with predictiveFailureLED=1(SCGCQ02154560 port of SCGCQ02137492)
 - LDET Q32018 - RRB130 - Enable iMR advanced debug dump to ttylog(SCGCQ02155177 port of SCGCQ02034476)
 - Different DDR tuning parameters(SCGCQ02176939 port of SCGCQ02130325)
 - Algorithm for setting user interrupt priority is incorrect.(SCGCQ01538676 port of SCGCQ01538100)
 - PL: SAS topology error - Device not addressable(SCGCQ02150954 port of SCGCQ02138806)
 - Performance drop observed with expander attached topology in latest firmware.(SCGCQ02141995 port of SCGCQ02105245)
 - PL: (SATA only) Proper Sense key not set to failed read/write command while handling NCQ error(SCGCQ02128295 port of SCGCQ01763871)
 - PL: SAS Drive Never Spun Up(SCGCQ02103006 port of SCGCQ02050654)
 - pl: backend PCIe: ECC6 fault(SCGCQ02102551 port of SCGCQ02007423)
 - PL Spinup: Firmware Takes a Long Time to Grant Spinup to Some Drives/Phys(SCGCQ02060281 port of SCGCQ01963394)
 - Data Abort Exception observed while running reboot test with a bad drive.(SCGCQ01995096 port of SCGCQ01985789)
 - Integrate latest MPI 2.6.8 header changes into Ventura.(SCGCQ01994798 port of SCGCQ01993555)
 - pl: backend PCIe: additional robustness for hot reset during SAS cycle case(SCGCQ01983403 port of SCGCQ01922270)
 - PL : Task management timeout is observed if the task management type is invalid(SCGCQ01979131 port of SCGCQ01969521)
 - SATA: IO Timeouts with Read/Write and Non-Automated IO(SCGCQ01967743 port of SCGCQ01958700)
 - (vSES) Injecting error on I2C channel of one connector module will cause LED of another connector module to not work.(SCGCQ01961503 port of SCGCQ01955094)
 - pl: backend PCIe: link may fail to come up(SCGCQ01947876 port of SCGCQ01929279)
 - Ventura: Use full Slot Cap Physical Slot Number field info for PCIe SW attached device slot enumeration(SCGCQ01941125 port of SCGCQ01936123)
 - PL UBM : SAS, SATA drives in Elrond UBM backplane(SFF-TA-1005) are not discovered when PCIe support is disabled(SCGCQ01918898 port of SCGCQ01897599)
 - Ventura: PLI control requests may return incorrect status when backend PCIe support is disabled(SCGCQ01912231 port of SCGCQ01887433)
 - PL UBM : SAS, SATA drives in Elrond UBM backplane(SFF-TA-1005) are not discovered when PCIe support is disabled(SCGCQ01911215 port of SCGCQ01897599)
 - pl UBM: Locate LED cannot be turned off after diag reset for few drives on Ex1 Elrond(SCGCQ01907168 port of SCGCQ01905070)
 - pl: backend PCIe: parent switch port lookup may generate incorrect pointer(SCGCQ01907148 port of SCGCQ01883220)
 - Ventura: Discovery may not complete, timeout on 94xx-8i HBA(SCGCQ01905232 port of SCGCQ01904851)
 - PL: NVMe drives do not link up on non Ex4 backplane attached to an MR board(SCGCQ01904802 port of SCGCQ01878217)
 - PL vSES: PCIe switch downstream virtual ports report SAS address of zero in SES page 0xA(SCGCQ01898485 port of SCGCQ01891238)
 - pl: port enable timeout and discovery failure with multiple VPP device configurations(SCGCQ01872008 port of SCGCQ01870862)
 - Add support for UBM backplane type during i2c communication(SCGCQ01732040 port of SCGCQ01687513)
 - Aero FPGA - API's to test smart recovery during Cache Offload(SCGCQ01765129 port of SCGCQ01757432)
 - Add 4G COL Single Image Support for specific OEM	(SCGCQ01873704 port of SCGCQ01789718)
 - Set temperature polling interval to 10 secs for drives attached to enclosure(SCGCQ01889453 port of SCGCQ01886412)
 - FlashcontrollerCount is displayed as 0 in colInfo(SCGCQ01891173 port of SCGCQ01850694)
 - Data abort if DevID of SAS PD is sent instead of NVMe PD for NVMe Passthrough(SCGCQ01920925 port of SCGCQ01915272)
 - Enabling EKMS over EKMS (initial developement(SCGCQ01924342 port of SCGCQ01877305)
 - Configure Correct GPIOs to detect and Set Back plane type(SCGCQ01928052 port of SCGCQ01926170)
 - Fix OCM copy when no dirty cache(SCGCQ01934964 port of SCGCQ01586776)
 - On UG bad PD removal and replaced with UG good PD, iMR allows Vd creation using 33 Pds(SCGCQ01937070 port of SCGCQ01921599)
 - SLT hangs, when user tries to fetch information about the Bad SAS PD(SCGCQ01948645 port of SCGCQ01848463)
 - Firmware changes to display "lastSuccessfulLearnTime" of BBU in storcli(SCGCQ01949089 port of SCGCQ01799162)
 - Read correct Back plane GPIOs for Back plane type detection(SCGCQ01949914 port of SCGCQ01932040)
 - NVMe Write Medium error handling(SCGCQ01950828 port of SCGCQ01747492)
 - MR 7.8 - OCR snapdump not getting generated(SCGCQ01957640 port of SCGCQ01942123)
 - Cannot be done initialize even if execute Full Initialize by using StorCli(SCGCQ01957645 port of SCGCQ01938067)
 - 9460-8i:"Other Error Count" of drives increase when running dd test(SCGCQ01965351 port of SCGCQ01943742)
 - power interruption during cache offload setup and erroneous FLASH region change(SCGCQ01970899 port of SCGCQ01957254)
 - Incorrect checks for LD invalid cases during IO processing caused data abort	(SCGCQ01988162 port of SCGCQ01950906)
 - FW hangs at "C0: mapVirtualMemory:" after a power cycle during IO(SCGCQ01990046 port of SCGCQ01971637)
 - OEM Specific:DM_Cfg_UpdateGPIOFromMfgPage6 and GPIOinit Cleanup(SCGCQ01994859 port of SCGCQ01943764)
 - Data Abort Exception on abrupt powerloss/reset when flushing events from NVRAM hold buffer to flash(SCGCQ02000447 port of SCGCQ01973389)
 - Host DCDB time out values are getting updated incorrectly(SCGCQ02009876 port of SCGCQ01986878)
 - factory re-purpose operation erases complete NVRAM.(SCGCQ02012359 port of SCGCQ02000851)
 - Handle SMART copy back failures and drive removals gracefully(SCGCQ02012425 port of SCGCQ01867686)
 - Adapter reset while running IOs on Bad PDs in dcdb path(SCGCQ02021210 port of SCGCQ01967922)
 - skip the link test if there is no qualifying pd attached(SCGCQ02029933 port of SCGCQ02018014)
 - MegaRAID Event Log discards old Event Log across OCRs.(SCGCQ02030758 port of SCGCQ01996044)
 - Controller Fatal Error is observed when Guest OS is reset from host in VMware environment(SCGCQ02030759 port of SCGCQ02011203)
 - Changes in reset_led to make it work for TTY_HIST_BBU_ON case(SCGCQ02034046 port of SCGCQ02031298)
 - "CmdBlocked: Clear is running on PD X" messages seen in the FW log when running a full init on a VD(SCGCQ02034971 port of SCGCQ02032414)
 - "CmdBlocked: Clear is running on PD X" messages seen in the FW log when running a full init on a VD(SCGCQ02034987 port of SCGCQ02032414)
 - PL Fault 00005853, while doing two copyback operations on lds with different block size.	(SCGCQ02034996 port of SCGCQ01970744)
 - ESXi 6.7 does not see JBODs during install or in vSphere.(SCGCQ02036959 port of SCGCQ01994684)
 - Un-Hide Drive Group is enabled after hiding a VD in HII(SCGCQ02039741 port of SCGCQ02032483)
 - Disable TransportReady In ICMR1(SCGCQ02042584 port of SCGCQ01828691)
 - Controller hang when MR is passthrough to the VM(SCGCQ02044291 port of SCGCQ02044166)
 - Fix an uninitialized variable to satisfy Coverity........................................(SCGCQ02048146 port of SCGCQ02046303)
 - For a specific OEM, in release 10.4, driver detected FW hang during I/O across all RAID levels with different background operations running(SCGCQ02048651 port of SCGCQ02008617)
 - MR7.10 Aero Si: Assert Occurs When Migration Completes & VD Goes Missing; I/Os Stop on All VDs(SCGCQ02048712 port of SCGCQ02015773)
 - FW reports "Disk test cannot start. No qualifying disks found" during the diagnostics test with multiple drives present(SCGCQ02058013 port of SCGCQ01990513)
 - Aero - FW returned "can't allocate sufficient mem" when trying to update Intel NVMe drive(SCGCQ02061616 port of SCGCQ02015867)
 - Critical Message " maximum supported count of 256 disks" received with MaX PDs(SCGCQ02064337 port of SCGCQ01884237)
 - Oldest event greater than current event causing get events not to work(SCGCQ02065797 port of SCGCQ02053936)
 - Controller no longer accessible after poweroff and poweron VMware virtual machine (VMware passthrough enabled(SCGCQ02069166 port of SCGCQ02013448)
 - [MR 7.11] Controller hang when IO is run on NVMe LDs	(SCGCQ02078627 port of SCGCQ02077939)
 - Unable to verify unmap support is disabled in nvdata due to "enableUnmapSupport" value not shown in nvdata MR PARAMS PAGE 0(SCGCQ02080935 port of SCGCQ02069052)
 - scsi status returned from host and out-of-band storlibtest is wrong(SCGCQ02081203 port of SCGCQ02051569)
 - Controller cache has been lost critical health message after warm reboot.(SCGCQ02081757 port of SCGCQ02046483)
 - Fault LED of drive doesn't glow intermittently for certain OEM expander systems.(SCGCQ02096323 port of SCGCQ02011236)
 - Controller Hang after multiple iterations of S4 Sleeper Stress Test(SCGCQ02099934 port of SCGCQ02059508)
 - Virtual disk created using 2 disks, unable to lock it(SCGCQ02102961 port of SCGCQ02090339)
 - Assertion failure during WJ write following a COL event when a VD goes through RLM(SCGCQ02106030 port of SCGCQ02080358)
 - Previous config missing error during boot after all VDs and JBODs had been deleted in previous boot(SCGCQ02107255 port of SCGCQ02083275)
 - Product Name, Firmware version and Package version details are not populated(SCGCQ02111726 port of SCGCQ01965631)
 - PFA condition was not detected(SCGCQ02113854 port of SCGCQ02069532)
 - Improve RMC SEEPROM logging(SCGCQ02118434 port of SCGCQ02106652)
 - Adapter reset due to an exception(SCGCQ02128228 port of SCGCQ02062791)
 - MR- 240VD Foreign import fails though the max limit is not hit.(SCGCQ02150535 port of SCGCQ02090769)
 - Storcli is not showing foreign configs using Ventura controllers if user has SED drive which is in foreign.(SCGCQ02150955 port of SCGCQ02060808)
 - Enhanced BGI is started on Raid 5 virtual drive(SCGCQ02164393 port ofSCGCQ02126960 )
 - PDB data path parity error workaround(SCGCQ02018319 port of SCGCQ01733783)
 - vSES: CRIT or NON CRIT bits in Enclosure Status Diagnostic page are never set(SCGCQ01995232 port of SCGCQ01942781)
 - PL Spinup: Firmware Takes a Long Time to Grant Spinup to Some Drives/Phys(SCGCQ01983381 port of SCGCQ01963394)
 - MR 7.8 Package fails to spin-up multiple SAS SPL-2 Power Control capable drives(SCGCQ01971660 port of SCGCQ01963504)
 - Ventura: OEM 24 drives PCIe Switch secondary VMD mode enable may not complete successfully(SCGCQ01960496 port of SCGCQ01957675)
 - 0x6001 Fault while running IOs and doing cable pulls(SCGCQ01942971 port of SCGCQ01937141)
 - Comments in plStates.c and plStates.h are wrong(SCGCQ01912136 port of SCGCQ01909770)
 - [vSES] Vendor ID and Product ID of Configuration diagnostic page uses hardcoded values.(SCGCQ01906462 port of SCGCQ01906013)
 - Incorrect vSES Data for Page 0x02 After Storcli Start & Stop Locate Operations for certain NVME Backplanes.(SCGCQ01893314 port of SCGCQ01671177)
 - Mismatch between data coming from Page2 and PageA in vSES(SCGCQ01885749 port of SCGCQ01859095)
 - pl: vSES reports incorrect product revision level in SES page 1(SCGCQ01883332 port of SCGCQ01877030)
 - Fault 4311 when running repeated controller resets(SCGCQ01872931 port of SCGCQ01865882)
 - Enable FC1 CS0 for toggle flash(SCGCQ01761561 port of SCGCQ01748562)
 - Firmware does not scrub last 32MB of DDR(SCGCQ01761581 port of SCGCQ01746064)
 - Disable TransportReady In ICMR1(SCGCQ01838706 port of SCGCQ01828691)
 - Controller OCR seen when DM multipathing issues read CDB with zero blocks(SCGCQ01849393 port of SCGCQ01808882)
 - OLTP performance regression on 24 Single Drive R0 config	(SCGCQ01877315 port of SCGCQ01850741)
 - IN FAILED ARRAY bit is not being set when a VD is cleared(SCGCQ01878351 port of SCGCQ01137359)
 - Memset the PinnedDataStructure when DRAM dirty signature is zero(SCGCQ01878417 port of SCGCQ01713149)
 - dirty led not set on in case of supercap not present even though dirty cache is present(SCGCQ01880994 port of SCGCQ01825031)
 - Unable to run IO's on max R0 config, 4 enclosures on each port(SCGCQ01881300 port of SCGCQ01818181)
 - FW enable/disable EKMS over OOB, downgrade protection and security migration(SCGCQ01924346 port of SCGCQ01889333)
 - CSCvc47490 - Often on PD insert PD Fault is asserted,de-asserted(SCGCQ01957294 port of SCGCQ01332964)
 - Firmware fault when continuously creating and deleting VDs/EPDs using attached batch script(SCGCQ02001091 port of SCGCQ01864769)
 - ICMR1 With Storlibtest (OOB) TR can be enabled on VD's it should be disabled(SCGCQ02002112 port of SCGCQ01909345)
 - bounds check not correctly performed on patrol read if media defect exists on the last block of PD(SCGCQ02002681 port of SCGCQ01942077)
 - Secure erase on JBOD drives using hdparam is failing sporadically(SCGCQ02030646 port of SCGCQ01904220)
 - Patrol Read should be enabled for SSDs drives VD(SCGCQ02032319 port of SCGCQ01979352)
 - H345 fails to create/delete/edit partitions in Windows on JBOD drive.(SCGCQ02034049 port of SCGCQ01978750)
 - Cache Flush Interval can be changed on iMR Controllers(SCGCQ02034159 port of SCGCQ01988420)
 - immediate error return from PL not always handled properly(SCGCQ02036594 port of SCGCQ01996107)
 - Data Abort Exception when Enclosure Status Page has "unrecov" bit set and PDAllowedOps command is issued on the enclosure PD(SCGCQ02038345 port of SCGCQ01968331)
 - Phy Connections count not sent properly to application(SCGCQ02040540 port of SCGCQ01970476)
 - H345 fails to create/delete/edit partitions in Windows on JBOD drive.(SCGCQ02060762 port of SCGCQ01978750)
 - MR_7.9: Snapdump is not triggered in "dmaErrorIsr" Error path.(SCGCQ02066354 port of SCGCQ01989936)
 - After reboot the Setup, the Boot Device will be to reset in HII(SCGCQ02150045 port of SCGCQ02127915)
 - Assertion failure in fw\hw\pce\fusion.c at line 744 seen while flashing the FW and VD creation/deletion.(SCGCQ02150177 port of SCGCQ02105135)
 - Initialize cache after diagnostics testing(SCGCQ02164689 port of SCGCQ02134286)
 - OOB - SLT shows incorrect output for reset controller option in controller Menu(SCGCQ02180934 port of SCGCQ02118879)
 - Move NVRAM hibernation signature definition to NVRAM header file(SCGCQ01902212 port of SCGCQ01886892)
 - logging SES event for the critical condition detected during SOD(SCGCQ01870863 port of SCGCQ01862477)
 - Secure erase on JBOD drives using hdparam is failing sporadically(SCGCQ01932387 port of SCGCQ01904220)
 - Implement SCGCQ01880847 in MR 7.9: Hit PL Fault 00005862 LinkRegister 01439171 During CC With Triple Media Errors On R60 4K Drives(SCGCQ01935118 port of SCGCQ01909922)
 - bounds check not correctly performed on patrol read if media defect exists on the last block of PD(SCGCQ01957636 port of SCGCQ01942077)
 - Phy Connections count not sent properly to application(SCGCQ02000072 port of SCGCQ01970476)
 -(SCGCQ02000768 port of SCGCQ01984675)
 - Possibility of data loss due to abrupt/asynchronous warm reset(SCGCQ02007828 port of SCGCQ01985158)
 - PERC10.4:ONFI: BBLIST RECLAIMALL does not purge factory bad blocks(SCGCQ02035198 port of SCGCQ01978319)
 - ICMR1 With Storlibtest (OOB) TR can be enabled on VD's it should be disabled(SCGCQ02035781 port of SCGCQ01909345)
 - Critical message seen at boot reporting max devices have been exceeded when booting iMR controller with 32 slot backplane(SCGCQ02039717 port of SCGCQ01990446)
 - Change default NVDATA setting to enable spindown only for SATA SSD.(SCGCQ02046553 port of SCGCQ02044267)
 - LSA7.9: When Prepare for removal is performed on all the UG Drives, click on Adv/simple configurations should be grayed out(SCGCQ02052337 port of SCGCQ01968110)
 - SATA SSDs are changing to powersave when a warm reboot is issued.(SCGCQ02081205 port of SCGCQ02053087)
 - Copyback failed on data drive when failed drive inserted back on EKMS encrypted VD(SCGCQ02085508 port of SCGCQ02077226)
 - Aero UTP: Assertion failure during WJ write following a COL event when a VD goes through RLM(SCGCQ02102489 port of SCGCQ02058372)
 - Slot ID changed from "98:7" to ":255" after issuing PD FW Upgrade command followed by same PD Pull Push(SCGCQ02106028 port of SCGCQ02083026)
 - Aero DBU PA4 : JBOD IO failure - unaligned read or write command	(SCGCQ02138172 port of SCGCQ02124585)
 - Before pd diag starts,shield diag fail event is logged.(SCGCQ02177060 port of SCGCQ02082118)
 - Enable FC1 CS1 discovery(SCGCQ01761560 port of SCGCQ01748733)
 - Fail to Set SSDSmartErEnabled to TRUE when copyback is disabled(SCGCQ01870881 port of SCGCQ01403999)
 - System x: SCSI SANITIZE/Crypto on JBOD Drives under MR(SCGCQ01878348 port of SCGCQ01129378)
 - Data Abort Exception on abrupt powerloss/reset when flushing events from NVRAM hold buffer to flash(SCGCQ01988181 port of SCGCQ01973389)
 - Fix the memory allocation issue for diag test(SCGCQ02042675 port of SCGCQ02042041)
 - Foreign status not shown on EKMS drive after runtime key exchange is done(SCGCQ02047749 port of SCGCQ02023636)
 - Incorrect SAS address in the timedout event(SCGCQ02060274 port of SCGCQ02031494)
 - Erase operation is disabled for EPD.(SCGCQ02062852 port of SCGCQ01937381)
 - Max number of PDs for PatrolRead to run concurrently should be in range from 1 to MR controller's max configurable PDs(SCGCQ02081309 port of SCGCQ02008420)
 - TTY logs shows incorrect drive type as 'SATA' for SAS HDD Cryptographic erase.(SCGCQ02106047 port of SCGCQ02100742)
 - Snapdumps may include empty files if one of the file streams exceeds the allocated buffer(SCGCQ02173715 port of SCGCQ02138164)
 - The SUT can’t boot to OS after 159 loops AC cycle and check the Raid 930-16i 8G(SCGCQ02000074 port of SCGCQ01788479)
 - Incorrect checks for LD invalid cases during IO processing caused data abort(SCGCQ02000917 port of SCGCQ01950906)
 - MR7.7: Missing diagnostic failed in event log when PD state goes ONLINE to SHIELD and then to FAILED(SCGCQ02002683 port of SCGCQ01927550)
 - SMP pass through not working when the “PD 0” is BAD drive(SCGCQ02030785 port of SCGCQ01945602)
 - During Firmware update, the message displayed for unsuccessfully updating MegaRAID card will be more descriptive and more compattbile with previous MegaRAID products.(SCGCQ02035204 port of SCGCQ01967058)
 - Getting invalid value selecting Manage controller mode in HII(SCGCQ02058098 port of SCGCQ01985983)
 - Aero A0_Pull/Push Cable caused an assertion with Multipath EPd+R0's(SCGCQ02085536 port of SCGCQ02048037)
 - Minimize performance impact from VDM driver workaround(SCGCQ02153755 port of SCGCQ02134921)
 - OCR/KA (if OCR is disabled(SCGCQ02000479 port of SCGCQ01940516)
 - Kill adapter issues by driver since Lun Reset hung in Firmware(SCGCQ02021257 port of SCGCQ02005549)
 - FW hangs at "C0: mapVirtualMemory:" after a power cycle during IO(SCGCQ02035199 port of SCGCQ01971637)
 - Cryptographic Erase operations are blocked for JBODs	(SCGCQ02035369 port of SCGCQ02010293)
 - Vses Device Type is displayed as Enclosure for iMR Board	(SCGCQ02100182 port of SCGCQ02080574)
 - LDET Q32018 - RRB130 - Enable MR advanced debug dump	(SCGCQ02154699 port of SCGCQ01873123)
 - Vses Slots are not updated after removing Multipath connection.(SCGCQ02176745 port of SCGCQ02154042)
 - Firmware hits Kill Adapter when create/initialize R0 VD using 4k drive.(SCGCQ01943907 port of SCGCQ01937998)
 - FW hit the assertion when user tries to change the PD state from failed to online state in IMR card(SCGCQ02150965 port of SCGCQ01997813)
 - Aero PA4: getting on-demand snapdump right after FW flashing causes a FW exception(SCGCQ02163734 port of SCGCQ02125329)

EnhancementRequests:
 - Update Aero NVDATA files for Eval board(SCGCQ01380065)
 - MPI 2.6: Associated header changes for MPI 2.6.8 release.(SCGCQ01991840)
 - Update Ventura Summary Release Notes(SCGCQ01944825)
 - Aero3: Modify "iop pci lnkspdr" so that it displays PCIe4 bus speed(SCGCQ01938727)
 - Aero-3: Rename Images(SCGCQ01938306)
 - Aero-3: Update IT release script & Create summary release notes(SCGCQ01937838)
 - Aero: Update PSW and CSW M0 firmware images(SCGCQ01928209)
 - Aero3: Change secure sign executable to HSM version	(SCGCQ01926107)
 - Enable DCW blocks in slave bypass(SCGCQ01924163)
 - pl: NVMe: MAXCMD(SCGCQ01922181)
 - Add workaround for SATA drive not complaint with ACS-3(SCGCQ01922154)
 - Aero-3: Use Atlas SES as top-level switch enclosure's SEP and update vSES to account for managed switches(SCGCQ01917691)
 - NVDATA settings to override SCL low and high times(SCGCQ01915614)
 - Remove AERO_PORTING from IOP & Bootloader files(SCGCQ01915534)
 - Remove AERO_PORTING from PL_FEATURE_ACTIVE_CABLE_SUPPORT(SCGCQ01915530)
 - Aero: backend PCIe: review Gen 3.5 hardware workarounds for removal(SCGCQ01904852)
 - Aero: Incorporate EFUSE Key Update code from SBLIB and associated logic(SCGCQ01900830)
 - Integrate MPI 2.6.7 release headers into Aero/Ventura code.(SCGCQ01892032)
 - Aero-3: Improve backend MPI device error handling(SCGCQ01891231)
 - MPI 2.6: Add new IOCStatus code for "FAILURE"(SCGCQ01889947)
 - Aero-3: Create 8 phy versions of NVDATA XSD files(SCGCQ01889946)
 - MPI 2.6: Header file changes for MPI 2.6.7 release(SCGCQ01889371)
 - pl: backend PCIe: update NVMe device requirements doc builder(SCGCQ01887377)
 - Aero: MPI spec IOC Page 1 - interrupt coalsecing change request (per reply queue group(SCGCQ01887289)
 - Aero: pass unhandled MPI toolbox messages to PL(SCGCQ01884405)
 - MPI 2.6: Defines in header must be unique in first 32 characters.(SCGCQ01883411)
 - Added Per-Device statistics/event collection(SCGCQ01883166)
 - Timestamp changed to represent the system time(SCGCQ01883165)
 - Aero: pl: identify Atlas using vendor specific capability(SCGCQ01872108)
 - Aero: Port package.exe to Aero(SCGCQ01871556)
 - Customer specific build(SCGCQ01870343)
 - Remove DMA_Q_MASK_STARVATION workaround for AERO(SCGCQ01868871)
 - Customer specific backplane and drive carrier discovery(SCGCQ01865592)
 - Aero: backend PCIe: add support for Atlas synthetic mode pseudo endpoints(SCGCQ01862353)
 - Port protocol cycling firmware workaround from Ventura to Aero(SCGCQ01859080)
 - NVMe Device Requirements document builder(SCGCQ01858472)
 - pl: NVMe: Device Init Failure event	(SCGCQ01857070)
 - Aero RMC: Separate the Aero version of RMC from the Ventura version.(SCGCQ01853689)
 - MPI 2.6: Header file changes for MPI 2.6.5 release(SCGCQ01853686)
 - MR CBB changes to account for latest cbb changes.(SCGCQ01850067)
 - Goldenx/Ventura: Add -s (signed bios image(SCGCQ01828984)
 - Update CBB UART speed handling(SCGCQ01824074)
 - Aero-3: Add support for 8 phy chips(SCGCQ01789033)
 - Aero3: GoldenX-Add functionality to understand component headers and create golden images for Aero3(SCGCQ01766802)
 - Aero-3: Create IT & PL/SCS Libs Release Scripts(SCGCQ01764972)
 - Aero-3: Enable MPI Endpoint to Atlas	(SCGCQ01736578)
 - Aero-3: Create production board NVDATA XSD(SCGCQ01732949)
 - MPI 2.6: Slot Numbering for x2/x4 wide connections to direct attached devices(SCGCQ01727225)
 - Aero: backend PCIe: retimer presence indication(SCGCQ01614679)
 - Aero-3: Review Aero PBAM changes	(SCGCQ01614626)
 - Aero3: SpiLib: CR #06 Addition - Add an "exclusion" table to the SPI RDID logic(SCGCQ01599294)
 - MPI 2.5: Add MaxEnclosureLevel field to BIOS Page 1(SCGCQ01570730)
 - MPI 2.5: Add OEMRD field to SAS Enclosure Page 0.(SCGCQ01553021)
 - Aero: backend PCIe: PCIe 4.0 lane margining interface(SCGCQ01439350)
 - NVRAM: Boot device should be presented as /dev/sda in Linux operating system(SCGCQ02044592)
 - API change to support new DCMD for consolidated device list(SCGCQ02037158)
 - API change to support NVMe Passthrough over OOB(SCGCQ02035295)
 - Additional details about spare(SCGCQ02033538)
 - API change to support new DCMD for consolidated device list(SCGCQ02016725)
 - NVRAM Changes align with MPB changes - support for Dual FW Image Download Shenandoah for OEM Hercules(SCGCQ02015824)
 - New NVDATA field for vendor identification qualification(SCGCQ02001314)
 - cache offload debug mode(SCGCQ01995737)
 - Added new functionality to the existing DCMD.(SCGCQ01954951)
 - Add opal support for all drive types.(SCGCQ01943832)
 - Addition of device type PSoC in MR_FW_SAS_PVT_API(SCGCQ01933134)
 - ROMENV.exe - Add -force for ignoring size alignment requirement(SCGCQ01931763)
 - Add Linux support to build tools(SCGCQ01905072)
 - NVDATA fields needed for Vision(SCGCQ01872736)
 - Remove Eval Defines for selected modules like DDR(SCGCQ01348373)
 - Create Secure Boot Library(SCGCQ01478545)
 - Secure Boot image validation support(SCGCQ01478605)
 - Generic Mode Commands(SCGCQ01510663)
 - PIO Work Mode Commands(SCGCQ01510683)
 - TLC Initialization Common Code(SCGCQ01519759)
 - AI for transport layer code collab reviews(SCGCQ01523373)
 - Aero Toggle : Changes to set feature for Toggle NAND during Init(SCGCQ01525522)
 - Generic mode read/write commands(SCGCQ01531744)
 - ONFI Debug Tools for FPGA Phase 1 Development.(SCGCQ01532241)
 - Aero Toggle : Enable multi plane support during COL initialization(SCGCQ01548025)
 - Implemented OTP Read for Factory Invalid Blocks(SCGCQ01556765)
 - AWLEN/ARLEN support in slave dma functions.(SCGCQ01573653)
 - Generic Mode Prints are too verbose(SCGCQ01573656)
 - Enabling DDR support on Aero Fpga(SCGCQ01573940)
 -(SCGCQ01575006) -
 - ONFI Debug Tools for FPGA Phase 2 (mainline(SCGCQ01578297)
 - megamon support on fpga	(SCGCQ01582719)
 - Implement COL Debug Routines for non-DDR mode.(SCGCQ01599621)
 - Debug API to read and compare parameter page(SCGCQ01601678)
 - Toggle : Adding NAND property and NAND action for Toggle.(SCGCQ01606718)
 - Aero Performance improvement(SCGCQ01614602)
 - disable ocm copy support(SCGCQ01619045)
 - Fix colPrepareOffloadMemList(SCGCQ01619930)
 - adding megamon command colfeatures.(SCGCQ01620237)
 - adding scrambling support define	(SCGCQ01620242)
 - Replace ValidChipSelectsDis with ValidChipSelectsDiscovered(SCGCQ01620295)
 - add colinfo megamon command(SCGCQ01623535)
 - Update debug routine which dumps command descriptor.(SCGCQ01630365)
 - CDMA support(SCGCQ01630382)
 - COL debug command module improvements(SCGCQ01641742)
 - fix smart recovery code in colReadyForOffloadEvent routine(SCGCQ01665139)
 - Enable DDR for Cache Offload	(SCGCQ01665159)
 - Megamon Cmd implementation for Block Stress, ECC & Scrambler enable/disable(SCGCQ01671233)
 - Implement HW assisted offload routine using CCR method of setting offload request bit(SCGCQ01676076)
 - Set Csysreq bits in MoMaskbitSmIso(SCGCQ01681734)
 - enable continue on error(SCGCQ01685880)
 - enable single image(SCGCQ01686755)
 - Debug API's to allow user to use custom blocks for Cache Offload.(SCGCQ01720589)
 - Implement new build target for compiling 2GB DDR support(SCGCQ01721593)
 - Cleaning up the wrapper module(SCGCQ01727262)
 - Modify read eye training to program/read cache instead of block(SCGCQ01729830)
 - Modify CBB builder for Avenger to add parameter for ETP binary image.(SCGCQ01735481)
 - Update SBR for Aero MR Validation board(SCGCQ01742027)
 - Validation Card Prep Items for the COMMON project(SCGCQ01762282)
 - Validation Card Prep Items for the Aero Integration project(SCGCQ01762283)
 - Implemented read retry mechanism for toshiba flahs part(SCGCQ01763112)
 - sblib: Efuse update support(SCGCQ01764966)
 - Debug API's do not use max ECC while reading or writing Flash Filesystem.(SCGCQ01788725)
 - Set test bits to simulate programming errors on Flash Device.(SCGCQ01788792)
 - Update colinfo debug API to print additional info.(SCGCQ01788803)
 - cache offload design note suggested changes to the metadata(SCGCQ01788805)
 - Moving OCM Copy code out of the Common code (COL_COMMON changes(SCGCQ01790409)
 - Eliminate header includes in main aero code(SCGCQ01796099)
 - Implement Secure Boot Library changes needed for MegaRAID(SCGCQ01797407)
 - rename define(SCGCQ01798111)
 - Implemented secureSign.exe CLI tool for automating FW signing process with signImageX(SCGCQ01799918)
 - Modify inline assembly(SCGCQ01800559)
 - Add wait build option(SCGCQ01807382)
 - Secure boot image check(SCGCQ01818132)
 - MR Init: Enable the second core(SCGCQ01824113)
 - Add the handling of API for discarding all the snapdumps(SCGCQ01824164)
 - Spec Compliance (Aero specific(SCGCQ01826016)
 - Disable efuse updates(SCGCQ01830292)
 - sblib: Improve key update test cases(SCGCQ01830308)
 - Create an enumeration for type of factory bad block scan(SCGCQ01837081)
 - code cleanup(SCGCQ01838010)
 - Added functionality to secureSign.exe to stamp the signed FW Image with the PublicKeyList ID for tracking purposes.(SCGCQ01839760)
 - sblib: Add sbliCompareKeys(SCGCQ01840951)
 - Secure Boot: debug port enable(SCGCQ01841005)
 - Add support for SAS/SATA Phy Power Management capabilities.(SCGCQ01841569)
 - SCons improvements(SCGCQ01847730)
 - Aero Personality Management(SCGCQ01849071)
 - NVDATA fields needed for Vision(SCGCQ01850499)
 - Aero JBOD Personality(SCGCQ01851746)
 - provide debug command to dump ecc info and good pointer blocks(SCGCQ01851750)
 - Block FW update (to a version where switch is not supported(SCGCQ01851839)
 - SCONS changes for ER:SCGCQ01856025 - Add CSW Aladin Plus FW to SBR portion of CBB image(SCGCQ01856249)
 - sblib: IT Integration issues(SCGCQ01857288)
 - Update Aero Build Scripts for Further SPI Lib Changes and Incorporate New PL(SCGCQ01858311)
 - SBLIB API functions need to do a sbliInitialize check(SCGCQ01861986)
 - Remove mpi dependency from sblib api(SCGCQ01864752)
 - Audit workarounds.h/.c for Aero A0(SCGCQ01865705)
 - sblib: Integrate sblib with Aero IT(SCGCQ01865928)
 - Fix NVMe Pass through implementation(SCGCQ01867566)
 - Use SOFA or SOFB to prepare for offload when there was no offload(SCGCQ01867713)
 - Add python path to genDebug.py call(SCGCQ01870009)
 - SBLIB: Add API's that allow the user to check all signatures in a component(SCGCQ01870043)
 - Add builder to invoke SecureSign.exe utility in order to sign images.(SCGCQ01870088)
 - Add new megamon command to enable/disable multiplane(SCGCQ01871839)
 - sblib: Audit for timeout loops(SCGCQ01872112)
 - Improve build compatibility(SCGCQ01878258)
 - sblib: Increase compatiblity by relocating/renaming global variables(SCGCQ01882599)
 - sblib: Add a library version(SCGCQ01882714)
 - Code review AI 32628	(SCGCQ01885769)
 - Aero: Prep work for Lane Margining(SCGCQ01887494)
 - SCONS changes for signing APP-FW image on Avenger.(SCGCQ01889213)
 - Update descriptor completion status in all Fc/Cs	(SCGCQ01897897)
 - Integrate RMC Logs into Snapdump, Collect snapdump for cache offload failures(SCGCQ01902742)
 - SBLIB: Populate secure boot status structure(SCGCQ01903769)
 - Add a new HW return status when all SOF/EOF are invalid(SCGCQ01905335)
 - Integrate RMC Logs into Snapdump, Collect snapdump for cache offload failures (aero change(SCGCQ01906520)
 - Add new failure status in COL_HW_STAT_T(SCGCQ01906633)
 - Add debug command for dumping info pertaining to Bad Block Table Flash(SCGCQ01907017)
 - Add UBM support For all the controllers(SCGCQ01907162)
 - SBLIB MR: Add sbliCompareKeys to MR FW Download routine(SCGCQ01907192)
 - Integrate RMC Logs into Snapdump, Collect snapdump for cache offload failures (aero change(SCGCQ01909926)
 - Move dev versions out of the registry(SCGCQ01913916)
 - Move PtrFlashIoMeta out of COL_FLASH_CHIP_SELECT Structure(SCGCQ01915596)
 - Adding SOC and PCE data to LSISAS3908.xsd(SCGCQ01917823)
 - Add support to dump OTP page (bad blocks	(SCGCQ01918693)
 - Cleanup colcommon.h structures to have all fields start with uppercase(SCGCQ01920028)
 - Enable 8x2 NVMe Lane config for channel products(SCGCQ01921438)
 - Structure change cleanup left over(SCGCQ01924034)
 - Add new debug cmds(SCGCQ01924054)
 - SBLIB: Modify key invalid routine to allow non-sequetial values(SCGCQ01924080)
 - Aero: Rec Completion Interrupts are changed from Edge Triggered in Ventura to Level triggered in Aero.(SCGCQ01924157)
 - Only do secure boot authentication on signed images (CBB, App, etc(SCGCQ01924581)
 - Remove the code that setting MSS PLL from FW.(SCGCQ01924681)
 - colMain.c cleanup to better display battery/super-cap info.	(SCGCQ01924954)
 - Adding a new builder to SCONS script to pad firmware image and update header size at the same time.(SCGCQ01924957)
 - Allow environment variables to override yaml defines	(SCGCQ01924973)
 - Improve Data Double Buffering logic in NVMe IO Path(SCGCQ01927393)
 - Some cleanup in colDebug.c and colCommon.c(SCGCQ01928206)
 - Method to read ROC Temp, Drive Temp, Drive Type, Drive Protocol and status through OOB BMC(SCGCQ01929671)
 - Addition of device type PSoC in MR_FW(SCGCQ01933128)
 - Aero initialization changes(SCGCQ01934286)
 - Add debug command to erase mpi0 for bad block table on toggle(SCGCQ01935020)
 - Perform prefill check of on-chip memory copy for offload(SCGCQ01936156)
 - Aero: Integrate Aero PL(SCGCQ01937148)
 - Enable NVRAM for cache offload idle loop(SCGCQ01942899)
 - Change to timing mode 3 for async and increase offload/restore timeouts(SCGCQ01943838)
 - Update onfiCheckOffloadImage no offload snapdump case(SCGCQ01943903)
 - Aero: Initial Integration of MCTP work(SCGCQ01943911)
 - Moving colMainCompleteInitialization in colMain.c (part of A0 bring up(SCGCQ01945020)
 - update the secureSign key to use HSM key.(SCGCQ01949115)
 - Fix for setting flash controller clock speed(SCGCQ01949310)
 - FW hangs on issuing a warm reset while trying to access DDR lib routines(SCGCQ01949344)
 - Set DRAM signature valid flag on col arm(SCGCQ01949442)
 - ReadEye Training updates	(SCGCQ01954755)
 - Drive Vendor ID qualification(SCGCQ01956466)
 - enable timing mode 6	(SCGCQ01957265)
 - Minor fixes in colDebug module(SCGCQ01957672)
 - Modify aero-prevalidation to match table under Secure Boot Mode in Security Arch(SCGCQ01958073)
 - Move flash file system refresh to createFS routine(SCGCQ01959004)
 - Add a debug routine to dump COL Nvram info(SCGCQ01959124)
 - Local copy of COL Nvram gets cleared after an OCR(SCGCQ01960773)
 - colinitslcblocks : remove arguments(SCGCQ01960908)
 - Aero A0 Exposure: R0 Autoconfig functionality not working on cold boot(SCGCQ01962833)
 - The debug command 'col startcolrestore' reportig restore failure after offload(SCGCQ01962835)
 - DDR tuning parameters based on subOEM ID	(SCGCQ01964424)
 - Remove MSS Reset Required check in Reset Status Register	(SCGCQ01971135)
 - Reduce the prints while booting to reach the pci release retry time out.(SCGCQ01971897)
 - MR sblib: Add Efuse Reset Interface in SbLib	(SCGCQ01971935)
 - MR sblib: Efuse Reset handling in Init and Error Recovery scenarios(SCGCQ01972032)
 - clean up mpi state code(SCGCQ01972150)
 - Add estimated offload time for toggle(SCGCQ01972158)
 - Invalid DramSignature in startcolrestore	(SCGCQ01979924)
 - Move function for verifying offload desc chain to after ocm restore(SCGCQ01982237)
 - Add rmc commands to MegaMon that enable/disable the RMC uart	(SCGCQ01988106)
 - Adding prints in tfm.c and colMain.c to print COL HW Status for better debug-ability.(SCGCQ01989946)
 - Fix 1GB SLC Init calculation	(SCGCQ01989962)
 - Clean up blocks allocation in case of no offload and invalid SOFA and B(SCGCQ01990076)
 - snapdump : the coldumpreg output is going to UART instead of snapdump(SCGCQ01991666)
 - The coldumpreg output is going to UART instead of snapdump (colSystem.h changes(SCGCQ01992622)
 - Aero: Enable x1 NVMe in the backend as an option to be selected by user(SCGCQ01995814)
 - Onfi Debug command(SCGCQ01999089)
 - Moves most cbDebug print statement from mprintf to etprintf.(SCGCQ02002750)
 - Move some error messages from monitor log to etty log.(SCGCQ02003602)
 - eTTY: Enable MPT Host Module Error prints to eTTY(SCGCQ02003609)
 - eTTY: Enable error prints by default from modules BBM/LDBBM/DMA/XOR/BBU(SCGCQ02003662)
 - Update LSISAS3908.xsd to be in sync with the latest LSISAS3916.xsd changes(SCGCQ02004083)
 - expand eTTY log from 6MB to 12MB	(SCGCQ02007576)
 - Enable Lane Margining support on host PCIe(SCGCQ02008736)
 - cache offload debug mode (N1 stream changes(SCGCQ02010086)
 - Spin up changes to Handle TUR failures with SCSI_ASCQ_NR_INITIALIZING_CMD_REQUIRED(SCGCQ02011387)
 - Fix memport code for Aero to detect 8i device correctly(SCGCQ02018602)
 - Debug-ability:Log Drive FW download extended message to etty(SCGCQ02020096)
 - Change minimum ECC level for toggle parts(SCGCQ02020277)
 - Change minimum ECC level for toggle parts(SCGCQ02023642)
 - Changes to improve internal FW Log debug for PL layer(SCGCQ02031339)
 - Porting MR on-demand snapdump support from MR 7.9 to Lenovo 19B stream(SCGCQ02032636)
 - Block un-map VDs to use SATA drives (that supports unmap	(SCGCQ02039596)
 - Aero : Clearing Failed Init bits in MSS MO Interrupt Status Error Register(SCGCQ02045239)
 - Add measurement of L1/L2/OCM flush time(SCGCQ02048278)
 - Add Build Time Print Statement Format Checking(SCGCQ02059746)
 - Need different log entry for timeout during unarmed reset sequence(SCGCQ02064121)
 - Snapdump - Dump all the valid TLB descriptors from TLB page pool in SRAM	(SCGCQ02064214)
 - Adding prints which will report whether cache offload was armed on previous boot.(SCGCQ02066888)
 - Add fmc builder to scons.(SCGCQ02084261)
 - Initialize OOB I2C Clock stretch value via NVDATA settings(SCGCQ02111614)
 - Supercap Monitor improvements(SCGCQ02190399)
 - Aero3: Implement PMU message to notify M0 to init serdes parameters(SCGCQ01940678)
 - Aero3: Make serdes debug output selectable(SCGCQ01934991)
 - Aero: Map CTL region for access to slave bypass registers.(SCGCQ01924811)
 - PL support for authenticating Customer specific genuine drive carriers.(SCGCQ01904334)
 - SPILIB: Modify initialization so that all devices uses 8 dummy bits for reads in dual and quad mode(SCGCQ01891968)
 - Aero3: Port function to set power mode of SAS phys(SCGCQ01887443)
 - pl: backend PCIe: enable firmware to handle vendor specific device(SCGCQ01884809)
 - Aero: Eliminate TPH and MSIX workarounds meant for Ventura/Marlin(SCGCQ01876851)
 - Aero: Allow "Soft Secure" parts to boot even if EFUSE is not programmed(SCGCQ01868688)
 - pl: backend PCIe: switch interrupt handler failure retries(SCGCQ01867808)
 - Aero: Enhance user protection by eliminating writes to signature areas(SCGCQ01800775)
 - Ventura: Modify firmware download algorthm so that the SOC SBR signature is invalid until the image is checked(SCGCQ01792449)
 - (NVMe(SCGCQ01627982)
 - Add MPI Comp Img headers (SB(SCGCQ01685810)
 - MR PVT API change to add support to control OOB I2C Clock Stretch Value(SCGCQ02111596)
 - MPB changes - support for Dual FW Image Download Shenandoah for OEM Hercules	(SCGCQ02015826)
 - Add dual image support for OEM Hercules for Shenandoah program(SCGCQ02006877)
 - added Smart Drive Carrier Authentication info in NVRAM.(SCGCQ01936489)
 - Aero COL Fpga build(SCGCQ01522361)
 - Evaluate PRP support for bmp_cmd_read(SCGCQ01529130)
 - Toggle : Add Timing parameter and operation mode settings(SCGCQ01598510)
 - Cache Offload Debug Commands - Phase 3(SCGCQ01601680)
 - Implement SuperCap cut line detection in FW.(SCGCQ01601703)
 - CCR ResetStatus User bits need to change in Aero(SCGCQ01602701)
 - Set the cache offload region(SCGCQ01619926)
 - Update colWrapperPrepFlashDescriptor to include fw/hw assisted parameter(SCGCQ01638328)
 - Disable flashRegionToggleReq flag on FPGA(SCGCQ01639799)
 - Aero COL FPGA: Disable auto discovery on 2nd flash controller(SCGCQ01681568)
 - Aero COL FPGA: Add FC1 no auto discovery flag in custom file(SCGCQ01681685)
 - Offfload and restore support(SCGCQ01681717)
 - Implement read retry feature as part of PIO and CDMA read commands(SCGCQ01685760)
 - Updating copyright info from Broadcom Ltd. to Broadcom Inc(SCGCQ01737586)
 - Atlas switch device end Base Mode support(SCGCQ01742087)
 - Move SOF metadata to pages immediately after file system (in the same block(SCGCQ01747431)
 - Create a different command descriptor structure for CDMA(SCGCQ01749445)
 - Support ARM compiler toolchain installation with spaces in path as well as multiple perl binary names(SCGCQ01760624)
 - Add a parameter in colWrapperPrepFlashDescriptor for DDR data descriptor(SCGCQ01760658)
 - Cleanup colWrapperCheckForDescFailures(SCGCQ01761574)
 - Aero: Evaluate if F_DDF_NVME_WORKAROUND is still needed in the FW(SCGCQ01763260)
 - Extended TTY Buffer(SCGCQ01772478)
 - Add dynamic section of NVRAM to snapdump(SCGCQ01777199)
 - Automate cache restore failure analysis - Part 1(SCGCQ01786618)
 - NAND Configuration A0 prep changes(SCGCQ01797364)
 - MR 3.5 FW snapdump support for host initiated snapdump(SCGCQ01804299)
 - UBM: MR support for direct access of I2C devices that are not specified in manufacturing page 43(SCGCQ01807200)
 - Validate OTP page read/write change for ONFI(SCGCQ01813030)
 - Merge new top level headers(SCGCQ01822511)
 - Disable makefiles(SCGCQ01823988)
 - Remove mpi3_type.h from sbliApi.h(SCGCQ01824159)
 - Spec Compliance: Setting Discovered Flag on BDF change(SCGCQ01826018)
 - update for ocm copy(SCGCQ01831005)
 - NAND Configuration A0 prep changes (main aero 7.9 N1 stream changes(SCGCQ01838648)
 - aero fpga new megamon command(SCGCQ01840847)
 - Adding 3908.xsd to Aero NVDATA XSD release.(SCGCQ01847749)
 - Enabling GPIO_DIRTY_DATA_LED for Aero(SCGCQ01855972)
 - SCons: Replace and remove perl based scripts with python equivalents(SCGCQ01866136)
 - Adding data retention polling routine(SCGCQ01866699)
 - Implement periodic refresh of bad block table - Phase 3(SCGCQ01866701)
 - Handle SMART copy back failures and drive removals gracefully(SCGCQ01867686)
 - Periodic refresh of flash filesystem	(SCGCQ01867915)
 - CBB to Main FW transition(SCGCQ01873594)
 - Keep inc directory local(SCGCQ01878222)
 - Update ONFI_DiscardImage to include WriteSof argument(SCGCQ01885801)
 - Change NOR flash block size to 512K as a step stone to final support of Macronix NOR flash(SCGCQ01886759)
 - Automate Failure Analysis when cache restore fails - Phase 2	(SCGCQ01889851)
 - [MR 7.9] API change to export "disable least latency mode"(SCGCQ01897611)
 - Disable 512K Support on Specific during Aero testing on Ventura controller for time being.(SCGCQ01902130)
 - Move combined reply code switching handling function under Workaround flag.(SCGCQ01902292)
 - Update ONFI_DiscardImage to include BlockEraseReq argument(SCGCQ01903707)
 - Add CBB Flashing Support to MR(SCGCQ01905985)
 - Update ROMIMAGE tool for MR CBB building	(SCGCQ01906532)
 - Shutdown Required Helper Function to request shutdown to applications(SCGCQ01917664)
 - Implemented changes to support remote signing using the HSM client application server for generating keys and signing automation.(SCGCQ01917757)
 - Move PtrFlashIoMeta out of COL_FLASH_CHIP_SELECT Structure(SCGCQ01920232)
 - Cleanup colcommon.h structures to have all fields start with uppercase (Main changes(SCGCQ01922335)
 - SBLIB: Break out the pre-validate checks from each api call and add standalone pre-validate api check for aero(SCGCQ01924173)
 - Disable Firmware UART input when SRK Write Protect is not enabled(SCGCQ01925849)
 - Add support for an NVDATA image argument to the create CBB builder(SCGCQ01927492)
 - Add SrkWriteProtect getter/setter to api(SCGCQ01933404)
 - Cache Offload BST Improvements(SCGCQ01933475)
 - Unnecessary Sens Errors fill TTYLOG, adversely affecting support of customer issues.(SCGCQ01934150)
 - OCM Copy Changes for Aero(SCGCQ01936942)
 - Disable Opal Support for all drive types on Perc Controllers.(SCGCQ01943008)
 - Misc fixes to enable SYNC mode using hardcoded values in place of read eye traning(SCGCQ01944008)
 - DdrVerify is failing because snapdump is overriding the memory DdrWrite was using after restore is done.(SCGCQ01951143)
 - Move nvram valid flag and nand actions pointer to HW config struct(SCGCQ01956337)
 - Cache Offload power loss updates(SCGCQ01957171)
 - OCM Copy changes(SCGCQ01957192)
 - Read Eye Training Debug(SCGCQ01960755)
 - add debug command for displying the mem list(SCGCQ01960915)
 - Move global parameters to cache offload hardware structure(SCGCQ01961659)
 - Move global parameters to cache offload hardware structure(SCGCQ01961995)
 - dummy function for cache offload(SCGCQ01971170)
 - Update tfm state after sending ready for offload doorbell to RMC(SCGCQ01973346)
 - Fix errors in Register File access(SCGCQ01974344)
 - Update LSISAS3916.xsd file according to Citra 16i board NVDATA review(SCGCQ01978270)
 - OEM Specific Aero Controller Bring up Changes(SCGCQ01979361)
 - Change toggle from timing mode 4 to timing mode 6(SCGCQ01980167)
 - H745P: Adding support for GPIO Pins(SCGCQ01982404)
 - MR sblib: Send event to host to indicate securemode(SCGCQ01982694)
 - Fix errors in Register File access(SCGCQ01983478)
 - Disable unmap feature on R5/6 only(SCGCQ01985917)
 - Spin down drives during system shut down(SCGCQ01988180)
 - Enhancement for invalid SGL error dump to dump the frame and compare pMpt->dataLength against accumulated into extTTY buffer.(SCGCQ01989961)
 - Quick fix to aerovision build failure(SCGCQ01990180)
 - Remove code to reduce DDR size by additional 416 MB for Aero(SCGCQ01995724)
 - FW changes for lane margining support(SCGCQ01998017)
 - Toshiba parts need to be SLCformatState > 1.(SCGCQ02003386)
 - eTTY : Enable error prints by default for modules - cache/Cfgi/DivertHW(SCGCQ02003615)
 - eTTY: Enable NVMe Error prints in eTTY by default(SCGCQ02003656)
 - cache offload debug mode (COL_COMMON changes(SCGCQ02010083)
 - COL Debug Mode left over (col_common(SCGCQ02023777)
 - Clear the bbuEnable in nvram when we disarm(SCGCQ02030024)
 - Cache Offload Failure Analysis on Ventura(SCGCQ02032360)
 - Enable NVME for Aero builds.(SCGCQ02039491)
 - Change the text for boot message BOOT_MSG_KEY_MISSING_REBOOT_OR_CONTINUE(SCGCQ02041803)
 - Update 7.10 XSD files to be synced with MR PVT API baseline(SCGCQ02111790)
 - Aero: backend PCIe: disable hot reset on link up(SCGCQ01926246)
 - Aero DDR: Implement new test mode for Analog SE(SCGCQ01925998)
 - Aero/Ventura: Add SPILIB test to verify SPI FLASH parts and libraries(SCGCQ01902039)
 - Aero: Update SecureBoot Library and use new functions to verify all signatures in a FwDownloaded image are valid(SCGCQ01868691)
 - MR PVT API change to add support for EFI OCR	(SCGCQ02013408)
 - Spin down drives during system shut down	(SCGCQ01988176)
 - Update RomEnv.exe to version 1.20(SCGCQ01907024)
 - MR PVT API change to add support for EKMS keys over OOB(SCGCQ01874046
 - Optimize scatter for Aero(SCGCQ01349665)
 - AI:Update COL offload metadata structure for ONFI 4(SCGCQ01522334)
 - Update COL offload metadata structure(SCGCQ01522336)
 - Use the erased page detection feature in the flash controller to check if a page is erased or not(SCGCQ01579850)
 - Add shell2acelite power management(SCGCQ01592273)
 - add mss reset prior to calling the DDR initialization function(SCGCQ01614119)
 - Disable flashRegionToggleReq on FPGA(SCGCQ01639805)
 - Search for NAND file system if COL NVSRAM not present(SCGCQ01683380)
 - Aero COL FPGA: Enable read/write caching in colHwInitialize(SCGCQ01684947)
 - Implement secure boot ctrl info(SCGCQ01685822)
 - expanded status values in COL_STATUS enumeration(SCGCQ01715047)
 - Implement periodic refresh of bad block table in flash(SCGCQ01767061)
 - Add debug API to run through all read retry options(SCGCQ01772624)
 - Add Flash Controller parameter to debug API's(SCGCQ01788721)
 - Debug Commands Issued after OCR will not work(SCGCQ01789579)
 - removing aerofpga2gbddr build support(SCGCQ01799229)
 -(SCGCQ01800890
 - SLC format changes(SCGCQ01804393)
 - MR Init: Add new flash header(SCGCQ01824114)
 - MR Init: Remove dead code from _start(SCGCQ01824115)
 - Add Debug Function DebugMPT_UpdatePCIeLinkFlagsUpdateAllLanes(SCGCQ01855365)
 - sblib: Add release component support(SCGCQ01867576)
 - request for new log info - bad block refresh(SCGCQ01870951)
 - Implement periodic refresh of bad block table - Phase 2 (main changes(SCGCQ01871924)
 - Ensure no unaligned access to NVRAM(SCGCQ01884049)
 - Add Full Package Flashing Support to MR(SCGCQ01924083)
 - Disable CACHE OFFLOAD code execution during Validation Board Bringup(SCGCQ01930754)
 - OCM Copy coding style changes(SCGCQ01937999)
 - colLoadNvramParam - function is corrupting nvram(SCGCQ01944906)
 - remove the 'Disable CACHE OFFLOAD code' workaround(SCGCQ01946597)
 - Add PD caching mode page dump to Snapdump(SCGCQ01947966)
 - Removing access to 0xFBA0_2000 which is valid for Cadence phy only(SCGCQ01948035)
 - Add a flag in colCheckPageErased to decide whether to print page erased status(SCGCQ01950915)
 - Update CRC for entire offload metadata structure written to NAND. Current code is creating CRC for header portion of struct(SCGCQ01951206)
 - Snapdump RTTrace DMA optimization and incorporation into module bitmaps(SCGCQ01951210)
 - Enable Read Eye Training	(SCGCQ01952451)
 - Fixing some debug APIs so the output is not truncated(SCGCQ01955680)
 - Disable read retry temporarily till SCGCQ01956439 is fixed(SCGCQ01956448)
 - Fix colPrepareOffloadMemList to use entire 8GB of DDR(SCGCQ01956451)
 - Update LSISAS3916 XSD for A0 EVAL Bring-up(SCGCQ01957165)
 - Disable SUPPORT_8GB_MEMORY flag(SCGCQ01957209)
 - New RMC log entries to parse(SCGCQ01957223)
 - RMC MegaMon commands need to be reintroduced(SCGCQ01958082)
 - re-enable 8GB DDR back(SCGCQ01958519)
 - Add rmcRingBuffer.h(SCGCQ01958996)
 - Move bad block table APIs in flash code to its own file(SCGCQ01963532)
 - Add Module parameter for atomic descriptor support for Aero family of controllers(SCGCQ01973356)
 - Move CCR Register File initialization from MR to RMC	(SCGCQ01979211)
 - Verifying Cache Offload request following soft reset and online controller reset.(SCGCQ01980121)
 - Provide quick summary of meta block(SCGCQ01982335)
 - Spin down drives during system shut down(SCGCQ01988154)
 - calling reclaimall on warm reboot does not create DDR entries(SCGCQ01993627)
 - Update NVDATA XSD ManPage 17 to enable the flag for enhancing Spinup control for Power control drives.(SCGCQ02013425)
 - Additional MR FW Changes Required for 8 PHY Board Support(SCGCQ02015712)
 - Unblock CPLD Image flashing and Block PSOC Image flashing for specific OEM(SCGCQ02020206)
 - COL Debug Mode left over(SCGCQ02023668)
 - LDET Q32018 - RRB130 - Enable iMR advanced debug dump to ttylog(SCGCQ02034476)
 - SSD perf BST automation integration with CQ(SCGCQ02092838)
 - Deterministic OCR command(SCGCQ00991465)
 - Cleanup COL flash filesystem related common code(SCGCQ01562242)
 - ONFI Debug Tools for FPGA Phase 2 Development (Common)(SCGCQ01563531)
 - enabling smart recovery(SCGCQ01676778)
 - Aero COL FPGA: update colMainIdleLoop to call colCheckCacheOffloadStatus(SCGCQ01679153)
 - Aero COL FPGA: enable scrambling in custom header(SCGCQ01685034)
 - Aero COL FPGA: CheckCacheOffloadStatusInit changes for COL glitch test(SCGCQ01715436)
 - Scan NAND for file system.(SCGCQ01729977)
 - Moving OCM Copy code out of the Common code (Aero INT changes(SCGCQ01790467)
 - Add IT/PL override directory(SCGCQ01790970)
 - OFFLOAD_COMPLETE_TIME_IN_SEC(SCGCQ01794943)
 - renaming define(SCGCQ01797985)
 - Add a SnapDump when there is a dirty cache, but the reference numbers are identical.(SCGCQ01804331)
 - NVME write uncorrectable error handling with SBBM.(SCGCQ01818436)
 - Add FW signing support to build(SCGCQ01822384)
 - Added support to main fw to use CBB initialized MMU mappings.(SCGCQ01824104)
 - Security should be based on a feature key(SCGCQ01838680)
 - Coarse Delay(SCGCQ01845138)
 - Realign ext trace buffer by phy addr to 16K alignment and enlarge ext trace buffer size(SCGCQ01851912)
 - Check status of HW initialize in colMainIdleLoop	(SCGCQ01855978)
 - Update SOF/EOF to include offload metadata for all FC/CS	(SCGCQ01858927)
 - Add debug command for dumping info pertaining to FlashFS and Offload meta(SCGCQ01867716)
 - Implement periodic refresh of bad block table - Phase 2 (col changes(SCGCQ01871958)
 - Add MR Support for Using New API to Configure Reply Queue Coalescing(SCGCQ01918918)
 - Cache Offload Activity stream for board bringup(SCGCQ01934376)
 - Aero Bringup: enhance host memory use instead of DDR(SCGCQ01935131
 - Properly set the flash controller speed(SCGCQ01942890)
 - Enable AYSN mode(SCGCQ01943002)
 - Fix to access to di_control register and some cleanup(SCGCQ01957235)
 - Enable workarounds for SERIES_3916(SCGCQ01957298)
 - Enable DDR2 Config for ONFI(SCGCQ01958134)
 - avoid snapdump for no offload cases(SCGCQ01959103)
 - Create debug command to reset refresh timestamp for bb table and flash fs(SCGCQ01961590)
 - Aero A0 Exposure: Firmware allows autoconfig R0 on JBOD personality(SCGCQ01969851)
 - Fault and wait for HCB if preboot fails secure boot authentication(SCGCQ01988080)
 - RAID 5 Performance Tuning(SCGCQ01998534)
 - eTTY : Enable DDF Module prints to eTTY(SCGCQ02003600)
 - COL Debug - Display status of Cache Offload triggering components(SCGCQ02037016)
 - HDD perf BST automation integration with CQ(SCGCQ02100995)
 - Aero COL TLC Flash Initialization for ONFI4.0(SCGCQ01509325)
 - Disable Flash Firmware Alias Support(SCGCQ01528648)
 - adding scrambling support define(SCGCQ01620244)
 - Store toggle bb table on a specific mpi on NAND flash(SCGCQ01803321)
 - Use sblib_rel and remove sblib's non-API paths from fwSConstruct's API_DIR_LIST list(SCGCQ01822453)
 - Add toolchain to ver command(SCGCQ01823992)
 - Aero Simplification: Reduce Aero profiles from 8 to 2(SCGCQ01838145)
 - MPT Layer IO tracker dump into Extended TTY(SCGCQ01855472)
 - LDET Q32018 - RRB130 - Enable MR advanced debug dump(SCGCQ01873123)
 - MR Secure Boot: handle tampered / invalid device	(SCGCQ01920003)
 - CCR: Add new functions to obtain DDR clock speed, and set Flash controller speed(SCGCQ01942822)
 - Move scolFlashNumControllers and scolFlashNumControllers to HW config struct(SCGCQ01954735)
 - Fixing a condition in colCheckOffloadImage so we go thorough snapdump save for all the cache offload/restore failure(SCGCQ01958298)
 - display both decimal and hex in the colinfo debug command(SCGCQ01960975)
 - Aero A0: Assertion failure in fw\raid\mpthostcmd.c at line 1992 while creating/deleting VDs/EPDs(SCGCQ01961982)
 - colDbgNvramInfo request(SCGCQ01962031)
 - Changes to support/fix offload info for snapdump(SCGCQ01969809)
 - remove the code which is reducing the DDR size by 416MB(SCGCQ01972154)
 - Commands : Generic Work Mode(SCGCQ01407649)
 - Support for the 2.3 bitstream(SCGCQ01635845)
 - Converting MR_FPGA to F_COL_IDLE_LOOP(SCGCQ01792705)
 - miscellanous cleanup(SCGCQ01799204)
 - Remove EpakSet function(SCGCQ01850574)
 - Testability improvement for Cache Offload(COL(SCGCQ01889942)
 - MR APP Bring-Up Vehicle for Aero A0 EVAL Board(SCGCQ01930642)
 - Port CSET changes from N1 dev Int stream	(SCGCQ01941148)
 - Reduce COL DDR size to 512MB for async mode(SCGCQ01943856)
 - Fix for setting flash controller clock speed(SCGCQ01949306)
 - Avoid Pcie Host address hardcoding(SCGCQ01949855)
 - Enable OTP page write(SCGCQ01961670)
 - Move global parameters to cache offload hardware structure(SCGCQ01961996)
 - Aero A0 Toggle flash bringup(SCGCQ01969808)
 - Changes to support/fix offload info for snapdump (Main Changes(SCGCQ01969874)
 - enable glitch functionality for aero(SCGCQ01956465)
 - OTP page for SLC Initialiization Clean up(SCGCQ01964374)
 - Add PDBb Interrupt handling(SCGCQ01965725)
 - Disable CACHE OFFLOAD code execution during Validation Board Bringup(SCGCQ01938709)
 - The data retention polling loop cant be called from col idle loop(SCGCQ01943004)
 - Move scolFlashNumControllers and scolFlashNumControllers to HW config struct(SCGCQ01953765)
 - Move setting the block and page to top level ReadEye Training function.(SCGCQ01970881)
 

Version 50.8.0-2659 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS: 7.08.02.0
	UEFI Driver: 0x07080401
	HII:  07.08.05.00
	MR FW: 5.080.00-2397
    package 50.8.0-2659
MR 7.8	
defects:
 - Phase0.8 Pre-Alpha Release Version 0.00.12.00 - SPI_LIBRARY (1)(SCGCQ02032981) 
 - Phase0.8 Pre-Alpha Release Version 00.250.05.00 - SAS3.5CtrlFw_Tip_Ventura_Ph_9.0 (9)(SCGCQ01942095) 
 - GCA Release Version 00.72.00.03 - MR_FW_SAS_Mega_API (2)(SCGCQ01943823) 
 - GCA Release Version 00.74.V0.02 - MR_FW_SAS_Mega_API (1)(SCGCQ02100201) 
 - Pre-Alpha Release Version 005.028.000.000 - MR_FW_SAS_Mega_API (1)(SCGCQ01851145) 
 - Alpha Release Version 005.030.000.000 - MR_FW_SAS_Mega_API (1)(SCGCQ01881298) 
 - ReleaseCandidate Release Version 005.036.000.000 - MR_FW_SAS_Mega_API (1)(SCGCQ01940381) 
 - Point Release Version 005.039.000.000 - MR_FW_SAS_Mega_API (1(SCGCQ02023146) 
 - Alpha Release Version 007.009.006.000 - MR_FW_SAS_Mega_API (1)(SCGCQ01978885) 
 - Pre-Alpha Release Version 007.011.000.000 - MR_FW_SAS_Mega_API (2)(SCGCQ02085647) 
 - Point Release Version 07.0800.0200.0100 - MR_FW_SAS_Mega_API (1)(SCGCQ01963790) 
 - Alpha Release Version 07.250.05.00 - SAS3.5CtrlFw_Ventura_Ph_8.0 (2)(SCGCQ01778146) 
 - Alpha Release Version 07.250.07.00 - SAS3.5CtrlFw_Ventura_Ph_8.0 (4)(SCGCQ01802477) 
 - Beta Release Version 07.250.09.00 - SAS3.5CtrlFw_Ventura_Ph_8.0 (1)(SCGCQ01827002) 
 - Beta Release Version 07.250.10.00 - SAS3.5CtrlFw_Ventura_Ph_8.0 (2)(SCGCQ01835588) 
 - ReleaseCandidate Release Version 07.250.13.00 - SAS3.5CtrlFw_Ventura_Ph_8.0 (2)(SCGCQ01850804) 
 - Point Release Version 08.25.00.00 - SAS3.5CtrlFw_Ventura_Ph_8.0_Point_MR (1)(SCGCQ01875210) 
 - Point Release Version 08.25.01.00 - SAS3.5CtrlFw_Ventura_Ph_8.0_Point_MR (1)(SCGCQ01906707) 
 - Point Release Version 08.25.02.00 - SAS3.5CtrlFw_Ventura_Ph_8.0_Point_MR (2)(SCGCQ01967505) 
 - Point Release Version 08.25.03.00 - SAS3.5CtrlFw_Ventura_Ph_8.0_Point_MR (1)(SCGCQ01978443) 
 - Point Release Version 08.25.05.00 - SAS3.5CtrlFw_Ventura_Ph_8.0_Point_MR (1)(SCGCQ01991188) 
 - Pre-Alpha Release Version 08.250.00.00 - SAS3.5CtrlFw_Tip_Ventura_Ph_9.0 (10)(SCGCQ01831602) 
 - Pre-Alpha Release Version 08.250.01.00 - SAS3.5CtrlFw_Tip_Ventura_Ph_9.0 (9)(SCGCQ01850286) 
 - Pre-Alpha Release Version 08.250.02.00 - SAS3.5CtrlFw_Tip_Aero_Ph_0.65 (1)(SCGCQ01856980) 
 - Alpha Release Version 08.250.03.00 - SAS3.5CtrlFw_Tip_Aero_Ph_0.65 (3)(SCGCQ01869871) 
 - Alpha Release Version 08.250.06.00 - SAS3.5CtrlFw_Ventura_Ph_9.0 (1)(SCGCQ01885806) 
 - Beta Release Version 08.250.08.00 - SAS3.5CtrlFw_Ventura_Ph_9.0 (3)(SCGCQ01900921) 
 - ReleaseCandidate Release Version 08.250.12.00 - SAS3.5CtrlFw_Ventura_Ph_9.0 (1)(SCGCQ01920133) 
 - Point Release Version 09.25.00.00 - SAS3.5CtrlFw_Ventura_Ph_9.0_Point_MR (3)(SCGCQ01935029) 
 - Point Release Version 09.25.01.00 - SAS3.5CtrlFw_Ventura_Ph_9.0_Point_MR (1)(SCGCQ01943128) 
 - Point Release Version 09.25.02.00 - SAS3.5CtrlFw_Ventura_Ph_9.0_Point_MR (3)(SCGCQ01971650) 
 - Point Release Version 09.25.04.00 - SAS3.5CtrlFw_Ventura_Ph_9.0 (1)(SCGCQ01990703) 
 - Point Release Version 09.25.05.00 - SAS3.5CtrlFw_Ventura_Ph_9.0_Point_MR (1)(SCGCQ01996141) 
 - Alpha Release Version 09.250.04.00 - ComboSerdes (1)(SCGCQ01932026) 
 - Pre-Alpha Release Version 0x07100000 - MR_FW_SAS_Mega_API (2)(SCGCQ01950950) 
 - Point Release Version 125.10.01.00 - ComboSerdes (1)(SCGCQ02044925) 
 - Pre-Alpha Release Version 2.10 - MR_FW_SAS3.5_7.8_FC (3)(SCGCQ01915515) 
 - Alpha Release Version 2.33 - MR_FW_SAS_Mega_API (2)(SCGCQ01916056) 
 - Point Release Version 4.680.00-8436 - MR_FW_SAS_Mega_API (1)(SCGCQ01964013) 
 - Alpha Release Version 4.680.01-8421 - MR_FW_SAS_Mega_API (1)(SCGCQ01927186) 
 - Point Release Version 4.740.00-8432 - MR_FW_SAS_Mega_API (2)(SCGCQ01964017) 
 - Pre-Alpha Release Version 414 - SAS3.5CtrlFw_Tip_Ventura_Ph_9.0 (2)(SCGCQ01957151) 
 - Pre-Alpha Release Version 5.051.00-1806 - SPI_LIBRARY (1)(SCGCQ01955455) 
 - Alpha Release Version 5.070.00-1481 - SAS3.5CtrlFw_Ventura_Ph_8.0 (3)(SCGCQ01778497) 
 - Beta Release Version 5.070.00-1497 - SAS3.5CtrlFw_Ventura_Ph_8.0 (1)(SCGCQ01800891) 
 - Beta Release Version 5.070.00-1517 - SAS3.5CtrlFw_Ventura_Ph_8.0 (1)(SCGCQ01822881) 
 - Beta Release Version 5.070.00-1531 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01829573) 
 - ReleaseCandidate Release Version 5.070.00-1576 - SAS3.5CtrlFw_Ventura_Ph_8.0 (1)(SCGCQ01852593) 
 - GCA Release Version 5.070.00-1615 - MR_FW_SAS3.5_7.7_FC (20)(SCGCQ01873341) 
 - Point Release Version 5.070.00-1659 - SAS3.5CtrlFw_Ventura_Ph_8.0_Point_MR (2)(SCGCQ01896722) 
 - GCA Release Version 5.070.00-1665 - MR_FW_SAS3.5_7.7_FC (9)(SCGCQ01900984) 
 - Pre-Alpha Release Version 5.070.00-1667 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (1)(SCGCQ01901764) 
 - Pre-Alpha Release Version 5.070.00-1674 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (3)(SCGCQ01904052) 
 - Pre-Alpha Release Version 5.070.00-1681 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (8)(SCGCQ01906894) 
 - Pre-Alpha Release Version 5.070.00-1742 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (26)(SCGCQ01925297) 
 - Pre-Alpha Release Version 5.070.00-1766 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (5)(SCGCQ01934822) 
 - Point Release Version 5.070.00-1779 - MR_FW_SAS3.5_7.7_FC (4)(SCGCQ01940904) 
 - Beta Release Version 5.070.00-1808 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (20)(SCGCQ01956107) 
 - Beta Release Version 5.070.00-1839 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (11)(SCGCQ01970485) 
 - Point Release Version 5.070.00-1867 - SAS3.5CtrlFw_Ventura_Ph_8.0_Point_MR (16)(SCGCQ01979474) 
 - Point Release Version 5.070.00-1884 - MR_FW_SAS3.5_7.7_FC (8)(SCGCQ01986403) 
 - Beta Release Version 5.070.00-1885 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (9)(SCGCQ01988000) 
 - Beta Release Version 5.070.00-1892 - SAS3.5CtrlFw_Ventura_Ph_8.0_Point_MR (6)(SCGCQ01991452) 
 - Point Release Version 5.070.00-1894 - SAS3.5CtrlFw_Ventura_Ph_8.0_Point_MR (1)(SCGCQ01991918) 
 - Beta Release Version 5.070.00-1909 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (2)(SCGCQ01994686) 
 - ReleaseCandidate Release Version 5.070.00-1916 - MR_FW_SAS3.5_7.7_FC_Lenovo19A (2)(SCGCQ01997677) 
 - Pre-Alpha Release Version 5.080.00-1484 - SAS3.5CtrlFw_Ventura_Ph_8.0 (2)(SCGCQ01788491) 
 - Pre-Alpha Release Version 5.080.00-1506 - SAS3.5CtrlFw_Ventura_Ph_8.0 (3)(SCGCQ01811098) 
 - Pre-Alpha Release Version 5.080.00-1521 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01826414) 
 - Pre-Alpha Release Version 5.080.00-1532 - SAS3.5CtrlFw_Ventura_Ph_8.0 (6)(SCGCQ01830363) 
 - Pre-Alpha Release Version 5.080.00-1538 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01838160) 
 - Pre-Alpha Release Version 5.080.00-1561 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01848191) 
 - Pre-Alpha Release Version 5.080.00-1577 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01853902) 
 - Alpha Release Version 5.080.00-1583 - SAS3.5CtrlFw_Tip_Ventura_Ph_9.0 (21)(SCGCQ01859156) 
 - Alpha Release Version 5.080.00-1584 - SAS3.5CtrlFw_Tip_Ventura_Ph_9.0 (20)(SCGCQ01859308) 
 - Alpha Release Version 5.080.00-1610 - SAS3.5CtrlFw_Tip_Aero_Ph_0.5 (2)(SCGCQ01872131) 
 - Alpha Release Version 5.080.00-1612 - MR_FW_SAS3.5_7.8_FC (4)(SCGCQ01872842) 
 - Alpha Release Version 5.080.00-1619 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01875256) 
 - Alpha Release Version 5.080.00-1655 - MR_FW_SAS3.5_7.8_FC (5)(SCGCQ01892166) 
 - Alpha Release Version 5.080.00-1666 - SAS3.5CtrlFw_Ventura_Ph_9.0 (3)(SCGCQ01900995) 
 - Alpha Release Version 5.080.00-1682 - SAS3.5CtrlFw_Ventura_Ph_9.0 (2)(SCGCQ01907030) 
 - Beta Release Version 5.080.00-1693 - MR_FW_SAS3.5_7.8_FC (4)(SCGCQ01910368) 
 - Beta Release Version 5.080.00-1722 - SAS3.5CtrlFw_Ventura_Ph_9.0 (2)(SCGCQ01917988) 
 - Beta Release Version 5.080.00-1735 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01921444) 
 - Beta Release Version 5.080.00-1747 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01927579) 
 - Beta Release Version 5.080.00-1752 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01929762) 
 - Beta Release Version 5.080.00-1760 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01932088) 
 - Beta Release Version 5.080.00-1761 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01932281) 
 - Beta Release Version 5.080.00-1768 - SAS3.5CtrlFw_Ventura_Ph_9.0_Point_MR (3)(SCGCQ01935266) 
 - ReleaseCandidate Release Version 5.080.00-1791 - MR_FW_SAS3.5_7.8_FC (5)(SCGCQ01945030) 
 - GCA Release Version 5.080.00-1802 - MR_FW_SAS3.5_7.8_FC (22)(SCGCQ01950925) 
 - Point Release Version 5.080.00-1822 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01962834) 
 - Point Release Version 5.080.00-1837 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01966730) 
 - Point Release Version 5.080.00-1840 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01970874) 
 - Point Release Version 5.080.00-1843 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01972103) 
 - Point Release Version 5.080.00-1891 - MR_FW_SAS3.5_7.8_FC (6)(SCGCQ01990744) 
 - Point Release Version 5.080.00-1915 - SAS3.5CtrlFw_Ventura_Ph_9.0_Point_MR (1)(SCGCQ01996172) 
 - Pre-Alpha Release Version 5.080.00-1935 - MR_FW_SAS3.5_7.8_FC_Lenovo19B (1)(SCGCQ02004039) 
 - Point Release Version 5.080.00-1965 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ02011201) 
 - Pre-Alpha Release Version 5.080.00-1966 - SAS3.5CtrlFw_Ventura_Ph_9.0_Point_MR (21)(SCGCQ02011408) 
 - Point Release Version 5.080.00-2007 - SAS3.5CtrlFw_Ventura_Ph_9.0_Point_MR (10)(SCGCQ02030694) 
 - Point Release Version 5.080.00-2013 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ02031335) 
 - Pre-Alpha Release Version 5.080.00-2017 - MR_FW_SAS3.5_7.8_FC_Lenovo_AMD (1)(SCGCQ02032653) 
 - Pre-Alpha Release Version 5.080.00-2044 - SAS3.5CtrlFw_Ventura_Ph_9.0_Point_MR (20)(SCGCQ02044314) 
 - Pre-Alpha Release Version 5.080.00-2069 - MR_FW_SAS3.5_7.8_FC_Lenovo_AMD (7)(SCGCQ02049981) 
 - Pre-Alpha Release Version 5.080.00-2070 - MR_FW_SAS3.5_7.8_FC_Lenovo19B (13)(SCGCQ02051021) 
 - Pre-Alpha Release Version 5.080.00-2099 - MR_FW_SAS3.5_7.8_FC (17)(SCGCQ02064981) 
 - Alpha Release Version 5.080.00-2137 - MR_FW_SAS3.5_7.8_FC_Lenovo19B (3)(SCGCQ02080028) 
 - Pre-Alpha Release Version 5.080.00-2138 - MR_FW_SAS3.5_7.8_FC (14)(SCGCQ02080537) 
 - Point Release Version 5.080.00-2144 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ02083511) 
 - Alpha Release Version 5.080.00-2202 - MR_FW_SAS3.5_7.8_FC_Lenovo19B (8)(SCGCQ02095446) 
 - Beta Release Version 5.080.00-2203 - MR_FW_SAS3.5_7.8_FC (15	(SCGCQ02096227) 
 - Beta Release Version 5.080.00-2283 - MR_FW_SAS3.5_7.8_FC_Lenovo19B (7)(SCGCQ02114133) 
 - Beta Release Version 5.080.00-2351 - MR_FW_SAS3.5_7.8_FC_Lenovo19B (2)(SCGCQ02127216) 
 - Beta Release Version 5.080.00-2354 - MR_FW_SAS3.5_7.8_FC_Lenovo19B (4)(SCGCQ02128523) 
 - Beta Release Version 5.080.00-2363 - MR_FW_SAS3.5_7.8_FC_Lenovo19B (1)(SCGCQ02132052) 
 - Point Release Version 5.080.00-2413 - MR_FW_SAS3.5_7.8_FC_Lenovo19B (3)(SCGCQ02138889) 
 - Pre-Alpha Release Version 5.080.02-1502 - SAS3.5CtrlFw_Ventura_Ph_8.0 (1)(SCGCQ01807383) 
 - Pre-Alpha Release Version 5.080.02-1656 - SAS3.5CtrlFw_Ventura_Ph_8.0 (3)(SCGCQ01892658) 
 - Beta Release Version 5.080.02-2362 - MR_FW_SAS3.5_7.8_FC_Lenovo_AMD (9)(SCGCQ02132036) 
 - Pre-Alpha Release Version 5.080.03-1621 - SAS3.5CtrlFw_Ventura_Ph_8.0 (22)(SCGCQ01876879) 
 - Alpha Release Version 5.080.10-1682 - MR_FW_SAS3.5_7.8_FC (2	(SCGCQ01907046) 
 - Pre-Alpha Release Version 5.090.00-1566 - MR_FW_SAS3.5_7.8_FC_Aero (12)(SCGCQ01849994) 
 - Pre-Alpha Release Version 5.090.00-1592 - SAS3.5CtrlFw_Tip_Aero_Ph_0.6 (29)(SCGCQ01863600) 
 - Pre-Alpha Release Version 5.090.00-1774 - SAS3.5CtrlFw_Ventura_Ph_9.0 (16)(SCGCQ01936644) 
 - Pre-Alpha Release Version 5.090.00-1778 - MR_FW_SAS3.5_7.8_FC (4)(SCGCQ01940709) 
 - Pre-Alpha Release Version 5.090.00-1810 - SPI_LIBRARY (95)(SCGCQ01957200) 
 - Alpha Release Version 5.090.00-1875 - MR_FW_SAS_Mega_API (1)(SCGCQ01982810) 
 - Beta Release Version 5.090.00-1983 - MR_FW_SAS_Mega_API (1)(SCGCQ02018875) 
 - Pre-Alpha Release Version 5.090.02-0755 - SAS3.5CtrlFw_Ventura_Ph_8.0 (3)(SCGCQ01832025) 
 - Pre-Alpha Release Version 5.090.02-1555 - MR_FW_SAS3.5_7.8_FC_Aero (8)(SCGCQ01846246) 
 - Pre-Alpha Release Version 5.090.02-1567 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01850245) 
 - Pre-Alpha Release Version 5.090.02-1578 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01854371) 
 - Pre-Alpha Release Version 5.090.02-1605 - MR_FW_SAS3.5_7.8_FC (3)(SCGCQ01867851) 
 - Pre-Alpha Release Version 5.090.02-1614 - MR_FW_SAS3.5_7.8_FC (9)(SCGCQ01873164) 
 - Pre-Alpha Release Version 5.090.02-1626 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01878199) 
 - Pre-Alpha Release Version 5.090.02-1630 - SAS3.5CtrlFw_Ventura_Ph_9.0 (2)(SCGCQ01880844) 
 - Pre-Alpha Release Version 5.090.02-1639 - MR_FW_SAS3.5_7.8_FC (2	(SCGCQ01885332) 
 - Pre-Alpha Release Version 5.090.02-1651 - SAS3.5CtrlFw_Ventura_Ph_9.0 (1)(SCGCQ01891331) 
 - Pre-Alpha Release Version 5.090.02-1671 - SAS3.5CtrlFw_Ventura_Ph_9.0 (6)(SCGCQ01902350) 
 - Pre-Alpha Release Version 5.090.02-1678 - SAS3.5CtrlFw_Ventura_Ph_9.0 (1)(SCGCQ01906097) 
 - Pre-Alpha Release Version 5.090.02-1704 - MR_FW_SAS3.5_7.8_FC (7)(SCGCQ01914025) 
 - Pre-Alpha Release Version 5.090.02-1709 - MR_FW_SAS3.5_7.8_FC (6)(SCGCQ01915405) 
 - Pre-Alpha Release Version 5.090.02-1726 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01918857) 
 - Pre-Alpha Release Version 5.090.02-1727 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01918878) 
 - Pre-Alpha Release Version 5.090.02-1730 - SAS3.5CtrlFw_Ventura_Ph_9.0 (5)(SCGCQ01919903) 
 - Pre-Alpha Release Version 5.090.02-1734 - SAS3.5CtrlFw_Ventura_Ph_9.0 (1)(SCGCQ01921321) 
 - Pre-Alpha Release Version 5.090.02-1739 - MR_FW_SAS3.5_7.8_FC (3)(SCGCQ01924956) 
 - Pre-Alpha Release Version 5.090.02-1756 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01930868) 
 - Pre-Alpha Release Version 5.090.02-1773 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01936288) 
 - Pre-Alpha Release Version 5.090.02-1784 - MR_FW_SAS3.5_7.8_FC (1)(SCGCQ01943092) 
 - Pre-Alpha Release Version 5.090.02-1830 - MR_FW_SAS3.5_7.8_FC (20)(SCGCQ01964183) 
 - Pre-Alpha Release Version 5.090.03-1701 - SAS3.5CtrlFw_Tip_Ventura_Ph_8.0 (39)(SCGCQ01912561) 
 - Pre-Alpha Release Version 5.090.03-1828 - MR_FW_SAS3.5_7.8_FC (2)(SCGCQ01963900) 
 - Pre-Alpha Release Version 5.090.09-1720 - SAS3.5CtrlFw_Ventura_Ph_9.0 (2)(SCGCQ01917622) 
 - Pre-Alpha Release Version 5.100.00-2004 - MR_FW_SAS_Mega_API (1)(SCGCQ02030581) 
 - Pre-Alpha Release Version 5.100.00-2016 - MR_FW_SAS_Mega_API (1)(SCGCQ02032531) 
 - Pre-Alpha Release Version 5.100.02-1847 - MR_FW_SAS3.5_7.8_FC (5)(SCGCQ01973029) 
 - Pre-Alpha Release Version 5.100.03-2026 - MR_FW_SAS_Mega_API (1)(SCGCQ02035582) 
 - Pre-Alpha Release Version 8.250.00.00 - SAS3.5CtrlFw_Tip_Ventura_Ph_9.0 (3)(SCGCQ01833109) 
 - Beta Release Version 9.00.02.00 - SPI_LIBRARY (1)(SCGCQ01830271) 
 - Remove changes ported from defect SCGCQ01937998.(SCGCQ01950909) 
 - pl: backend PCIe: EC59 fault on switch attached resource allocation failure(SCGCQ01840007) 
 - Aero: CBB linker warns of overlapped sections(SCGCQ01856283) 
 - pl: backend PCIe: ECD2 fault(SCGCQ01856306) 
 - Ventura: OEM ID66 PCIe Switch backplane Slots Status Amber LEDs stay blinking(SCGCQ01687610) 
 - pl: NVMe: ECF0 fault(SCGCQ01790929) 
 - Interrupts not handled in fault state if a high priority interrupt handler faults(SCGCQ01802508) 
 - MCTP: 0x265D fault occurs when running high MCTP PCIe VDM load with MCTP Discovery commands(SCGCQ01790303) 
 - Ventura B0: 0x5842 fault while running IOs and error injection tests(SCGCQ01780777) 
 - Fault 4311 when running repeated controller resets(SCGCQ01865882) 
 - ISTWIToolBox command returns garbage data(SCGCQ01818214) 
 - SPI_LIBRARY: Eliminate the need for "zip" exectuable for all but the "release" builds(SCGCQ01830243) 
 - Set discovery status error when unaddressable device is found(SCGCQ01750119) 
 - Ventura: The SPI_LIBRARY release directory referenced in the PL auto build script doesn't exist(SCGCQ01832795) 
 - Ventura: FW may fault 265Dh when attached to TA-1005 UBM Enclosures(SCGCQ01836829) 
 - pl: NVMe: E40E fault on NVMe shutdown of uninitialized NVMe device(SCGCQ01840036) 
 - I2C Back Plane detection fails(SCGCQ01850098) 
 - pl: backend PCIe: debug code for SCGCQ01845211(SCGCQ01858455) 
 - Ventura: NVMe I2C Backplane Detection fails on HBA connectors C2/C3 resulting in Slots not responding to LED updates(SCGCQ01886810) 
 - PL vSES: PCIe switch downstream virtual ports report SAS address of zero in SES page 0xA(SCGCQ01891238) 
 - Secure LD Creation with Dedicate Hot spare fails(SCGCQ01890955) 
 - Handle missing changes of CSET(SCGCQ01318495	(SCGCQ01904051) 
 - MR API - Incorrect value used for MR_DCMD_CTRL_SNAPDUMP_ONDEMAND(SCGCQ01882581) 
 - pl: NVMe: Solid State Media log page is missing(SCGCQ01807305) 
 - (SATA Only) Sense descriptor not filled properly for SCSI ATA Passthrough command failed by drive with SDA bit set.(SCGCQ01784132) 
 - PL SATL: SANITIZE Command failing for SATA SMR drives with ZNR bit set(SCGCQ01800567) 
 - Removed log message that was impacting customer(SCGCQ01828314) 
 - MR fw doesn't report that SAS_SATA 6 G and 3G capability(SCGCQ01870194) 
 - Reverting the changes delivered.(SCGCQ01886389) 
 - ChianMid issue handling for NVMe based volumes(SCGCQ01922016) 
 - 77: FW can not inject Medium error into customer NVMes drive with big size of 4.0Tb(SCGCQ01905236) 
 - FW crashes when pinned cache is generated with multiple VDs(SCGCQ01936690) 
 - bounds check not correctly performed on patrol read if media defect exists on the last block of PD(SCGCQ01942077) 
 - Ventura: Attaching multiple PCIe switches may cause IOP memory corruption(SCGCQ01853893) 
 - During drive spin up, drives come up as 0 bytes(SCGCQ01944951) 
 - Unwanted prints removed(SCGCQ01873256) 
 - MR7.7: Missing diagnostic failed in event log when PD state goes ONLINE to SHIELD and then to FAILED(SCGCQ01927550) 
 - Driver detected a FW hang with Jbod create and Del with Ctrl property change	(SCGCQ01970454) 
 - Data Abort Exception observed while running reboot test with a bad drive.(SCGCQ01985789) 
 - Phy Connections count not sent properly to application(SCGCQ01970476) 
 - PL Spinup: Firmware Takes a Long Time to Grant Spinup to Some Drives/Phys(SCGCQ01963394) 
 - (SATA Only) When ATA command fails with sense data available bit set, Data frame may not be released.(SCGCQ01732835) 
 - pl: backend PCIe: port enable may complete before PCIe mode is attempted (part 2)(SCGCQ01727593) 
 - pl: NVMe: unexpected switch attached task management timeouts(SCGCQ01763332) 
 - pl: backend PCIe: debug info for port enable subsystem integration(SCGCQ01817645) 
 - Incorrect Element status reported in SES Page 2 by vSES when connected to an expander(SCGCQ01822333) 
 - PL needs to check if we have a path to the end device before issuing a device reset to an NVMe drive as a part of TM	(SCGCQ01826234) 
 - Ventura: OEM PCIe dual switch attached backplane slot status LED stays Amber on partial slots(SCGCQ01788989) 
 - pl: backend PCIe: ECC7 fault(SCGCQ01771244) 
 - C++ version of SPI library being included in MR SCS Lib releases(SCGCQ01853784) 
 - rework to address Coverity flagged issues(SCGCQ01855394) 
 - Ventura: 265Dh Fault observed while accessing SFF-TA-1005 UBM backplane device(SCGCQ01826919) 
 - Ventura/Aero: ALADIN_PAGE45_INIT_FLAGS_STRUCT has too many bits (should be 32)(SCGCQ01830026) 
 - pl: backend PCIe: EC3D fault(SCGCQ01835042) 
 - Ventura MSS: Multi-bit ECC, EFI SAS DRIVER issue seen when performed multi reboot stress from UEFI(SCGCQ01794025) 
 - Aero/Ventura: Remote Flash (rmtf.rom	(SCGCQ01384845) 
 - 0x7211 Fault hit with more than one Elrond Ux4 midplanes attached(SCGCQ01850593) 
 - Forcing rebuild of multiple drives while activity is occurring can have data misdirected to the wrong drive and hit an assertion.(SCGCQ01849986) 
 - pl: Handle partial PCIe Link configs for SFF TA 1005 UBM support(SCGCQ01857152) 
 - pl: SAS/SATA devices not discovered with partial backplane configuration(SCGCQ01870842) 
 - MR7.8: Failed to downgrade FW from MR 7.8 FW pkg1661 to MR 7.5 pkg 1121 GCA with no meaningful message; returned "Image corrupted"(SCGCQ01890061) 
 - Ventura MSS: VRef training failures on Marlin/Pocono boards.(SCGCQ01891340) 
 - Debug output contains multiple copies of the same information(SCGCQ01899293) 
 - MR7.8: Locate a UBad drive on SGPIO no LED blinking (Still stays as UBAD	(SCGCQ01902159) 
 - MR 7.8 BST : FW hang at POST because of continuous FW log print " parseMuError: VF 4 - FMU Error Status 0x00000000 "(SCGCQ01909346) 
 - PL: NVMe drives do not link up on non Ex4 backplane attached to an MR board(SCGCQ01878217) 
 - Ventura: IOC init may fail with Host Page Size Invalid LogInfo on backend PCIe disabled FW(SCGCQ01916779) 
 - At booting POST screen, boot message indicating exceeding disks limit of 138 devices but the actual count is only 48 in system(SCGCQ01915675) 
 - application show "enable unmap" incorrectly(SCGCQ01921540) 
 - foreign import failed when sequence number mismatch(SCGCQ01912560) 
 - Snapdump generation in KA scenario results to CPU 0 exception or hang condition(SCGCQ01918724) 
 - vSES SES Page 0Ah may report same SAS address for two elements during hot remove/add of NVMe devices(SCGCQ01934145) 
 - PL SATL: Firmware Tries to Double Free Resource Mid(SCGCQ01934945) 
 - MR_7.8: Fail to perform OCR , after FW upgrade from MR 7.7 to 7.8(SCGCQ01823917) 
 - MR_7.8:Personality change with reboot result to Assertion failure in fw\raid\mon.c at line 654: 0(SCGCQ01840759) 
 - MR 7.8 - OCR snapdump not getting generated(SCGCQ01942123) 
 - copyback fail to start on some PDs(SCGCQ01839637) 
 - Check the usage of SGE address in DmProcessBufferWaitQueue(SCGCQ01866804) 
 - Check NULL pointer in display function called by snapdump to avoid data abor exception(SCGCQ01892152) 
 - Fix Alignment of ENCL_INFO struct members in 7.8	(SCGCQ01905512) 
 - MR 7.8 - RDM Error sense codes and medium error LBA updated twice(SCGCQ01922376) 
 - Reconstruction R1 to R5 by adding a pd found a drive of R1 became unconfig bad(SCGCQ01819285) 
 - host issued UNMAP cmd not handled properly when VD is offline(SCGCQ01920370) 
 - MegaRAID Event Log discards old Event Log across OCRs.(SCGCQ01996044) 
 - MR 7.8 Package fails to spin-up multiple SAS SPL-2 Power Control capable drives(SCGCQ01963504) 
 - Remove CSET SCGCQ01961503(SCGCQ01990091) 
 - FW hit the assertion when user tries to change the PD state from failed to online state in IMR card(SCGCQ01997813) 
 - PL: SAS Drives Take a Long Time to Link Up and Are Not Discovered Correctly(SCGCQ01973566) 
 - Able to set PR maxconcurrentpd as 0 for MR or iMR Ventura via Storcli(SCGCQ02040519) 
 - Incorrect SAS address in the timedout event(SCGCQ02031494) 
 - When drive is pulled keep last valid slot number in Events Generated. This was introduced with changesets SCGCQ01520443 and SCGCQ01584278(SCGCQ02017502) 
 - Controller hang when MR is passthrough to the VM	(SCGCQ02044166) 
 - MR to iMR Foreign import fails with mem alloc failure(SCGCQ02052312) 
 - Kill Adapter if PD FW download is run in continous loop(SCGCQ02059825) 
 - iMR Snapdump remove intermediate buffer size restriction.(SCGCQ02064738) 
 - Controller Fatal Error is observed when Guest OS is reset from host in VMware environment(SCGCQ02011203) 
 - Un-Hide Drive Group is enabled after hiding a VD in HII(SCGCQ02032483) 
 - Storcli is not showing foreign configs using Ventura controllers if user has SED drive which is in foreign.(SCGCQ02060808) 
 - PFA condition was not detected(SCGCQ02069532) 
 - Lenovo 19B: Vses Device Type is displayed as Enclosure for Boynton 8i Board(SCGCQ02080574) 
 - Spelling for SnapDump appears with "Sending SanpDump" once log file is opened.(SCGCQ02085505) 
 - Avoid sending intercore request to copy core1 holding buffer every 10ms(SCGCQ02053681) 
 - Increase the sram heap for iMR(SCGCQ02083966) 
 - MR- 240VD Foreign import fails though the max limit is not hit.(SCGCQ02090769) 
 - SL shows successful message if user set Max PDs on which PR can be run concurrently for any number(SCGCQ02102597) 
 - FW crash - MonTask: line 152 in file fw\raid\utils.c rst=0 while doing FW downgrade in iMR card(SCGCQ02102820) 
 - Assertion failure in fw\hw\pce\fusion.c at line 744 seen while flashing the FW through immraidtest and VD creation/deletion .(SCGCQ02105135) 
 - After reboot the Setup, the Boot Device will be to reset in HII(SCGCQ02127915) 
 - Ventura B0: Controller fault 0x7C41 observed during IO+System power cycle test(SCGCQ01790305) 
 - Host utils data for Download tty does not match with FW tty buffer dump.(SCGCQ02123014) 
 - pl: NVMe: Reference Temperature in the Temperature log page is incorrect	(SCGCQ01807465) 
 - FW exception error caused by OOB aborting active command.(SCGCQ01826311) 
 - Fix to CSET SCGCQ01605489(SCGCQ01837880) 
 - Ventura PL: New HW Workaround for 0x670A Fault(SCGCQ01841683) 
 - Erase operation is not happening on Multiple VDs	(SCGCQ01835727) 
 - Aero PA0.6: Data Abort during boot with pinned cache present. Exception Reason: Translation Fault Level 3 LONG on Int(SCGCQ01850764) 
 - Aero PA0.6 - IO Throughput drops drastically after issuing target reset to all drives with no IO going.(SCGCQ01807418) 
 - Aero PA0.6: FW "Assertion failure in fw\raid\mon.c at line 650: 0" encountered when 2 R5 VDs go offline(SCGCQ01816635) 
 - pl: NVMe: TransferCount in the SCSI IO error reply message may be invalid(SCGCQ01830303) 
 - pl: NVMe: unexpected read/write IO failure with SkipCount error(SCGCQ01835109) 
 - Aero PA0.6: FW fails to allocate memory for snapdump buffer after a forced OCR by driver(SCGCQ01824169) 
 - Aero3 RMC: Fix reset of PSW M0 in RMC reset code	(SCGCQ01698264) 
 - pl: backend PCIe: EC59 fault after failed switch discovery(SCGCQ01824028) 
 - Aero PA0.6: Using OOB Legacy APP you can not create second VD on the controller.(SCGCQ01826147) 
 - Eliminate a storm of AR deletion activity with max-configuration when ten enclosures are shut off(SCGCQ01841657) 
 - IO not completing or being timed out if some cases when an unconfirmed response is received for an IO.(SCGCQ01718897) 
 - Register type definition for Status register is incorrect.(SCGCQ01753001) 
 - FlashcontrollerCount is displayed as 0 in colInfo(SCGCQ01850694) 
 - Ventura: Fault 0x2805 encounted if one configures NVME and AutoPortEnable at the same time(SCGCQ01868375) 
 - iMR global fault LED does not get lit up during fail or UBAD	(SCGCQ01877036) 
 - Fw downgrade from 7.8 to lower version that does not support unmap(SCGCQ01878300) 
 - No profile reported when a bad (0-byte(SCGCQ01897779) 
 - pl: backend PCIe: unsupported completion timeout capabilities don't cause init failure(SCGCQ01906471) 
 - VenturaB0: SAS/SATA drives are not getting discovered with NVMe disabled firmware on both Crusader 9400-16iB0 and 9405W-16iB0(SCGCQ01876271) 
 - MR7.8: HII does not have the force option to switch personality when a configuration is present(SCGCQ01891348) 
 - Create Medium Error on NVME drive fail.(SCGCQ01937149) 
 - Upto 17% performance drop observed on single drive R0 NVME drive setup(SCGCQ01931276) 
 - SPI flash write verification error when flash suspend feature is enabled.(SCGCQ01747153) 
 - TaskMgmt Reset on NVMe BP triggered "FP Error lmid=434 smid=1 cdb0=2a status=2d devId=2 tgtId=8 devH=13" rolling nonstop	(SCGCQ01790853) 
 - Cache Error Boot Msg Change(SCGCQ01824359) 
 - SPI_LIBRARY: Add make.exe for systems without a gmake in their path(SCGCQ01830047) 
 - Aero: backend PCIe: 265D fault with more than 1 Atlas switch	(SCGCQ01832995) 
 - MCTP: Fault 0x265D when packet with StartOfMsg is set and PktSeqCount is 1(SCGCQ01850721) 
 - Ventura: UBM1005: Avoid PCIe reset request to FRU Port Descriptor unsupported PCIe drive types in DFC slots(SCGCQ01858809) 
 - pl: Fault 0xECAD while issuing controller reset in Ex1 configuration	(SCGCQ01859166) 
 - Unmap VD foreign import failure(SCGCQ01876232) 
 - MR7.8 9480-8i8e: IO dropped on EPD during overnight cable pull/push(SCGCQ01889215) 
 - Correct the Check Condition status reported by MR FW when a RAIDed slot behind a vSES device is accessed(SCGCQ01906705) 
 - Controller crashes when creating secured Vd using controller encryption option(SCGCQ01915880) 
 - zcdump cmd not working on all debuggers connected through Moxa(SCGCQ01917768) 
 - Issue: MR FW asserted after copyback completed and the source drive was removed.(SCGCQ01921307) 
 - AI - code collab review for SCGCQ01631254(SCGCQ01804236) 
 - vSES Listing multiple Array Device Elements for wide port devices (i.e., x2 or x4 NVMe or Wide SAS(SCGCQ01810677) 
 - Aero PA0.6 - !DC! Found while running multipath ping pong test after ~10 hours(SCGCQ01828044) 
 - FW may fail to complete device discovery with certain TA-1005 UBM backplane configurations(SCGCQ01845203) 
 - pl: backend PCIe: PCIe port enable may time out(SCGCQ01849314) 
 - MR_7.8 : Fails to delete the snapdump ..	(SCGCQ01850643) 
 - MR_7.8: During system reboot IMR card logged an event "log discontinuity due to buffer full"(SCGCQ01872802) 
 - Only Detect 63 Drives in Mix mode enviroment (Total 64 PDs in the system	(SCGCQ01885194) 
 - This change fixes Snapdump RTT Trace feature, by completing API change that came in after testing was completed.(SCGCQ01905234) 
 - With the IMR controller IOMMU fault is observed with the latest driver allow both RDPQ array or linear array.(SCGCQ01928086) 
 - Unmap setting is not getting enabled with the new NVDATA(SCGCQ01818568) 
 - TM and IO Failure with NVMe Drives on PL 8.250.2.0(SCGCQ01863348) 
 - DDF corruption after hibernation because of incorrect virtual address mappings(SCGCQ01877879) 
 - SDRAM Data Retention Mask didn't reset in firmware log when run battery retentiontest(SCGCQ01848274) 
 - Ventura B0: SAS and SATA drives may not get discovered on 9400-8e/16e(SCGCQ01851537) 
 - pl: NVMe: SCSI log page temperature may be incorrect in some cases(SCGCQ01804437) 
 - NULL references from DDF_VdRecEntryGet and DDF_VdParamEntryGet(SCGCQ01837102) 
 - Fix CSET activity SCGCQ01824060(SCGCQ01837984) 
 - Ventura PL: 0x670A Fault During Destructive Domain Testing(SCGCQ01831332) 
 - when user deletes the whole config, drive state is not reverted back.(SCGCQ01831965) 
 - erroneous configurable PD count decrement(SCGCQ01864432) 
 - Ventura PL: Check in Revised Workaround for 0x5842 fault - Rx Dma Memory Overflow(SCGCQ01864843) 
 - pl: Fault 0xED22 seen on bootup(SCGCQ01868009) 
 - pl: port enable timeout and discovery failure with multiple VPP device configurations(SCGCQ01870862) 
 - Update NumberOfPciSwitches in pliRuntimeConfig at SOD(SCGCQ01871061) 
 - FW downgrade blocking for JBOD personality used incorrect FW version number(SCGCQ01884199) 
 - Update the common header file to avoid compilation fail.	(SCGCQ01886583) 
 - Unmap operation during init/recon/rebuild/copyback(SCGCQ01889717) 
 - cache restoration failed	(SCGCQ01883439) 
 - Ventura: OEM SW Enclosure Amber LED stays on after reboot(SCGCQ01898852) 
 - Ventura: Discovery may not complete, timeout on 94xx-8i HBA(SCGCQ01904851) 
 - Raid volume(using SED drives(SCGCQ01870199) 
 - erroneous configurable PD count decrement(SCGCQ01873044) 
 - MR7.8-9460-16i: Controller Profile 14 still show SAS/SATA PDs(SCGCQ01890070) 
 - pl: NVMe: E40A fault if WRPROTECT or RDPROTECT is nonzero(SCGCQ01892105) 
 - MR7.8 PA2: Security property is always shown false for a DG when Secured VD is created via LSA in SLES 15(SCGCQ01848923) 
 - Mismatch between data coming from Page2 and PageA in vSES(SCGCQ01859095) 
 - Hit PL Fault 00005862 LinkRegister 01439171 During CC With Triple Media Errors On R60 4K Drives(SCGCQ01880847) 
 - MR_7.8:Driver unload and leave the system overnight, result to Assertion(SCGCQ01889482) 
 - Comments in plStates.c and plStates.h are wrong(SCGCQ01909770) 
 - pl: backend PCIe: parent switch port lookup may generate incorrect pointer(SCGCQ01883220) 
 - Enable "supportClearSnapDump" API bit(SCGCQ01874526) 
 - pl: backend PCIe: link fails to come up after a surprise down(SCGCQ01886012) 
 - pl: backend PCIe: bug when setting up direct attached PL structures(SCGCQ01915755) 
 - OPAL Support for NVME only(SCGCQ01917645) 
 - Controller not responsive(SCGCQ01922023) 
 - Discard the snapdump when a new firmware is flashed while there was a snap dump present.(SCGCQ01931954) 
 - undo previous fix; previous fix introduces undesirable side effects(SCGCQ01932051) 
 - Immediately rm for cache offload when TTY log is set to be preserved	(SCGCQ01838839) 
 - Disable debug queue support(SCGCQ01880124) 
 - FW reports that the board passed BBU Retention test on boards that have a non operational ONFI NAND memory.(SCGCQ01891177) 
 - On ESXi6.7U1 OS, With the IMR controller IOMMU fault is observed with the latest driver(SCGCQ01893479) 
 - Revert back OEM PR that lower the DDR speed to 1866 on OEM's custom designed baord(SCGCQ01898364) 
 - Handle reentrancy of Snap dump creation & correct run time pinned cache snap dump handler(SCGCQ01906056) 
 - MR7.8 OEM: WT VD created on attempt to create WB VD(SCGCQ01916098) 
 - 8GB DDR ECC event logging issue(SCGCQ01760839) 
 - Maintain integrity of Enclosure Diagnostic page status bits between MR FW internal monitoring routines and host reads(SCGCQ01816769) 
 - fixed by new oem nvdata ROP(SCGCQ01883121) 
 - Fix firmware parsing for Admin NVME pass through command with IOCStatus != success(SCGCQ01884233) 
 - FW hit "failed element size check !! ... tail pointer 65535 exceeds max 255" while OCR and rebuilding in loop(SCGCQ01886840) 
 - Removing unwanted printf and include	(SCGCQ01897953) 
 - IOC_CTRL_OP_ALL_PHY_LOOPBACK operation is not working(SCGCQ01670396) 
 - Flash suspend feature is partially disabled based on initialization input option.(SCGCQ01750006) 
 - pl: backend PCIe: port enable may complete before PCIe mode is attempted	(SCGCQ01760627) 
 - Ventura Phase 9 build failure(SCGCQ01830200) 
 - Aero: backend PCIe: buffer overflow during discovery of cascaded switches(SCGCQ01832807) 
 - limit target queue depth not greater than controller queue depth(SCGCQ01841594) 
 - rework to address Coverity flagged issues(SCGCQ01855152) 
 - When checking the config sequence number mismatch, need to cover system PDs.	(SCGCQ01871037) 
 - MR7.8: While doing SED JBOD drive pull on iMR, FW hit Assertion failure in fw\dm\pl3.5\pliopi.c at line 1164: 0(SCGCQ01876358) 
 - Ventura/Aero: makespi.cmd has a system command not supported on some build systems(SCGCQ01829985) 
 - Ventura: PLI control requests may return incorrect status when backend PCIe support is disabled(SCGCQ01887433) 
 - [MR 7.8] Recursive snapdump handling(SCGCQ01929759) 
 - All NVMe LED (Good/Fault LED	(SCGCQ01936961) 	
 - pl: backend PCIe: potential for link degradation after multiple link downs(SCGCQ01848040 port of SCGCQ01793209) 
 - (SATA only) Self-test offline immediate status received from drive is not populated to SCSI log sense command.(SCGCQ01714280 port of ) 
 - pl: backend PCIe: port enable may complete before PCIe mode is attempted	(SCGCQ01794153 port of SCGCQ01760627) 
 - IOC_CTRL_OP_ALL_PHY_LOOPBACK operation is not working(SCGCQ01792619 port of SCGCQ01670396) 
 - [Ventura][PL] Applications trying to update NVMe device Firmware with Mode E fails.(SCGCQ01868160 port of SCGCQ01624790) 
 - vSES: CRIT or NON CRIT bits in Enclosure Status Diagnostic page are never set.(SCGCQ01967410 port of SCGCQ01942781) 
 - vSES: Remove, RRAbort and Missing bits in array device element are not getting updated in element status page.(SCGCQ01967385 port of SCGCQ01932394) 
 - Ventura: Use full Slot Cap Physical Slot Number field info for PCIe SW attached device slot enumeration(SCGCQ01969772 port of SCGCQ01936123) 
 - IOP: MCTP: Add NVDATA timeout parameter on message re-assembly(SCGCQ01836908 port of SCGCQ01223839) 
 - Race condition can allow IOs over OOB to removed drive, with no host IOs, to not be cleaned up, and possibly leading to new drives not showing up(SCGCQ01807248 port of SCGCQ01400110) 
 - (SATA Only	(SCGCQ01839609 port of SCGCQ01833392) 
 - Ventura: Attaching multiple PCIe switches may cause IOP memory corruption(SCGCQ01857051 port of SCGCQ01853893) 
 - PL Fault 0x6001 occurred while running IOs + Task Management requests(SCGCQ01931043 port of SCGCQ01850755) 
 - Add workaround for SATA drive not complaint with ACS-3(SCGCQ01924984 port of SCGCQ01922154) 
 - 0x6001 Fault while running IOs and doing cable pulls(SCGCQ01942971 port of SCGCQ01937141) 
 - The Aero3 build does not compile(SCGCQ01971131 port of SCGCQ01944855) 
 - SATA: IO Timeouts with Read/Write and Non-Automated IO(SCGCQ01967743 port of SCGCQ01958700) 
 - vSES: CRIT or NON CRIT bits in Enclosure Status Diagnostic page are never set.(SCGCQ01995232 port of SCGCQ01942781) 
 - IO not completing or being timed out if some cases when an unconfirmed response is received for an IO.(SCGCQ01767091 port of SCGCQ01718897) 
 - MCTP PCIe VDM: controller stops responding after sending over 1000 asynchronous events(SCGCQ01760767 port of SCGCQ01742362) 
 - Race condition can allow IOs over OOB to removed drive, with no host IOs, to not be cleaned up, and possibly leading to new drives not showing up(SCGCQ01605489 port of SCGCQ01400110) 
 - Investigate on unalligned IO's for 512E drives with background operation	(SCGCQ01866862 port of SCGCQ01181178) 
 - Aero BST failure, Raid LD tgtId does not persist through OCR	(SCGCQ01873049 port of SCGCQ01857416) 
 - To support the SEP reset functionality through CPERST in order to avoid warm boot CPLD issues(SCGCQ01851006 port of SCGCQ01765873) 
 - [Ventura][PL] TM Hangs when doing drive push pull test case(SCGCQ01817008 port of SCGCQ01792208) 
 - Heavy IO with low IO timeout test may result into an IO getting missed.	(SCGCQ01867066 port of SCGCQ01631346) 
 - Firmware exception during rebuild on SAS and SATA R1 VDs that has 500 medium errors(SCGCQ01878349 port of SCGCQ01816682) 
 - erroneous configurable PD count decrement(SCGCQ01882408 port of SCGCQ01864432) 
 - [ventura] PL Fault 0000ecc9 observed, while running doing drive Pull-Push with IO's in background(SCGCQ01817257 port of SCGCQ01804290) 
 - Line 535 in ../../raid/cachePreserve.c for trying to create Pinned Cache by Cable Pull.(SCGCQ01878338 port of SCGCQ01839662) 
 - Error restoring offloaded (single image controller(SCGCQ01885343 port of SCGCQ01826923) 
 - Reduce bootup time by 15-20 seconds(SCGCQ01892778 port of SCGCQ01735563) 
 - The SUT can’t boot to OS after 159 loops AC cycle and check the Raid 930-16i 8G(SCGCQ01902777 port of SCGCQ01788479) 
 - Exposing Write cache as disabled to host for a performance improvement	(SCGCQ01901468 port of SCGCQ01845298) 
 - Same EID assigned to 2 530-8i controllers(SCGCQ01903444 port of SCGCQ01883096) 
 - Legacy BIOS Prints "This firmware is a TEST version"	(SCGCQ01901447 port of SCGCQ01825992) 
 - [vSES] Vendor ID and Product ID of Configuration diagnostic page uses hardcoded values.	(SCGCQ01906460 port of SCGCQ01906013) 
 - 9440-8i / 9460-16i cards BCA_S LED state doesn't match with BCA-S LED Behavior Rule.	(SCGCQ01902766 port of SCGCQ01832279) 
 - CIT: Same EID assigned to 2 930-8i controllers	(SCGCQ01902802 port of SCGCQ01830180) 
 - Check the usage of SGE address in DmProcessBufferWaitQueue(SCGCQ01918166 port of SCGCQ01866804) 
 - ICMR1 With Storlibtest (OOB	(SCGCQ01914261 port of SCGCQ01909345) 
 - iMR global fault LED does not get lit up during fail or UBAD	(SCGCQ01915782 port of SCGCQ01877036) 
 - Unmap setting is not getting enabled with the new NVDATA	(SCGCQ01919539 port of SCGCQ01818568) 
 - Only Detect 63 Drives in Mix mode enviroment (Total 64 PDs in the system	(SCGCQ01917261 port of SCGCQ01885194) 
 - Reconstruction R1 to R5 by adding a pd found a drive of R1 became unconfig bad(SCGCQ01919532 port of SCGCQ01819285) 
 - Eliminate a storm of AR deletion activity with max-configuration when ten enclosures are shut off(SCGCQ01920037 port of SCGCQ01841657) 
 - 530-8i- iMR Controller crashes during IO DMA operation(SCGCQ01911311 port of SCGCQ01830392) 
 - Firmware ASSERT(SCGCQ01911892 port of SCGCQ01729837) 
 - Forcing rebuild of multiple drives while activity is occurring can have data misdirected to the wrong drive and hit an assertion.(SCGCQ01912487 port of SCGCQ01849986) 
 - When checking the config sequence number mismatch, need to cover system PDs.	(SCGCQ01914298 port of SCGCQ01871037) 
 - Critical Message " maximum supported count of 256 disks" received with MaX PDs(SCGCQ01918227 port of SCGCQ01884237) 
 - CSCvm32376 - Fatal firmware error: Line 120 in ../../raid/utils.c(SCGCQ01919551 port of SCGCQ01895764) 
 - limit target queue depth not greater than controller queue depth	(SCGCQ01920041 port of SCGCQ01841594) 
 - Check NULL pointer in display function called by snapdump to avoid data abor exception(SCGCQ01914622 port of SCGCQ01892152) 
 - MR7.7: FW hit Assertion failure in fw\raid\mpthostcmd.c at line 1951: DMGetSpanFromDevhandle(pMpt- >DevHandle(SCGCQ01917260 port of SCGCQ01763331) 
 - copyback fail to start on some PDs	(SCGCQ01919504 port of SCGCQ01839637) 
 - Aero PA0.7: FW breaks into montask with exceptional core handling error(SCGCQ01919585 port of SCGCQ01850596) 
 - MR7.8: While doing SED JBOD drive pull on iMR, FW hit Assertion failure in fw\dm\pl3.5\pliopi.c at line 1164: 0(SCGCQ01915852 port of SCGCQ01876358) 
 - Aero PA0.6: FW "Assertion failure in fw\raid\mon.c at line 650: 0" encountered when 2 R5 VDs go offline(SCGCQ01917259 port of SCGCQ01816635) 
 - Disable debug queue support	(SCGCQ01930418 port of SCGCQ01880124) 
 - Secure LD Creation with Dedicate Hot spare fails	(SCGCQ01929133 port of SCGCQ01890955) 
 - No profile reported when a bad (0-byte	(SCGCQ01914532 port of SCGCQ01897779) 
 - Secure erase on JBOD drives using hdparam is failing sporadically(SCGCQ01929056 port of SCGCQ01904220) 
 - dirty led not set on in case of supercap not present even though dirty cache is present(SCGCQ01866204 port of SCGCQ01825031) 
 - copyback fail to start on some PDs(SCGCQ01934952 port of SCGCQ01839637) 
 - CSCvm76418 - Locate LED for UG and JBOD drives connected to Talledega is not off after hot plug.(SCGCQ01942462 port of SCGCQ01927362) 
 - Secure LD Creation with Dedicate Hot spare fails	(SCGCQ01907189 port of SCGCQ01890955) 
 - Error notification LED can't be stay long when drive pulled from VD.	(SCGCQ01944350 port of SCGCQ01882216) 
 - MR_7.8:Driver unload and leave the system overnight, result to Assertion	(SCGCQ01949646 port of SCGCQ01889482) 
 - Assertion is hit during region lock release due to inconsistent region lock promotion related variables(SCGCQ01915567 port of SCGCQ01863948) 
 - Issue: MR FW asserted after copyback completed and the source drive was removed.	(SCGCQ01940107 port of SCGCQ01921307) 
 - MR_7.8: Fail to perform OCR , after FW upgrade from MR 7.7 to 7.8(SCGCQ01936411 port of SCGCQ01823917) 
 - With the IMR controller IOMMU fault is observed with the latest driver allow both RDPQ array or linear array.(SCGCQ01942615 port of SCGCQ01928086) 
 - Fix Alignment of ENCL_INFO struct members in 7.8	(SCGCQ01945684 port of SCGCQ01905512) 
 - Handle missing changes of CSET(SCGCQ01318495	(SCGCQ01919498 port of SCGCQ01904051) 
 - On ESXi6.7U1 OS, With the IMR controller IOMMU fault is observed with the latest driver(SCGCQ01929982 port of SCGCQ01893479) 
 - host issued UNMAP cmd not handled properly when VD is offline(SCGCQ01940967 port of SCGCQ01920370) 
 - MR7.8 OEM: WT VD created on attempt to create WB VD	(SCGCQ01942129 port of SCGCQ01916098) 
 - MR7.8 PA2: Security property is always shown false for a DG when Secured VD is created via LSA in SLES 15(SCGCQ01942543 port of SCGCQ01848923) 
 - Heavy MFI based LD IO writes during POST causing WJ entries exhaust on iMR and FW asserting(SCGCQ01942509 port of SCGCQ01930815) 
 - Fw hit drvspinup.c when wake up from hibernation	(SCGCQ01948887 port of SCGCQ01912208) 
 - (vSES Injecting error on I2C channel of one connector module will cause LED of another connector module to not work.(SCGCQ01961504 port of SCGCQ01955094) 
 - Firmware fault when continuously creating and deleting VDs/EPDs using attached batch script(SCGCQ01962221 port of SCGCQ01864769) 
 - SATA: IO Timeouts with Read/Write and Non-Automated IO(SCGCQ01966771 port of SCGCQ01958700) 
 - (NVME) Fw Fault (faultcode 0xEC56) hit while performing system reboot test with NVMe drives attached.(SCGCQ01944366 port of SCGCQ01932728) 
 - OCR/KA (if OCR is disabled(SCGCQ01968461 port of SCGCQ01940516) 
 - 9460-8i:"Other Error Count" of drives increase when running dd test(SCGCQ01969749 port of SCGCQ01943742) 
 - foreign import failed when sequence number mismatch	(SCGCQ01968758 port of SCGCQ01912560) 
 - Cannot be done initialize even if execute Full Initialize by using StorCli(SCGCQ01968776 port of SCGCQ01938067) 
 - undo previous fix; previous fix introduces undesirable side effects	(SCGCQ01966532 port of SCGCQ01932051) 
 - MR_7.8: Fail to perform OCR , after FW upgrade from MR 7.7 to 7.8(SCGCQ01899545 port of SCGCQ01823917) 
 - Exposing Write cache as disabled to host for a performance improvement(SCGCQ01900925 port of SCGCQ01845298) 
 - Observed Fatal Firmware Error on Talledega card during SLES 12 O/S installation.	(SCGCQ01927603 port of SCGCQ01909779) 
 - Incorrect vSES Data for Page 0x02 After Storcli Start & Stop Locate Operations for certain NVME Backplanes.(SCGCQ01897348 port of SCGCQ01671177) 
 - (SATA Only) SCSI Start Stop Unit command with power condition set to standby may fail for SATA drives.(SCGCQ01867137 port ofSCGCQ01833392 ) 
 - Same EID assigned to 2 530-8i controllers(SCGCQ01892544 port of SCGCQ01883096) 
 - Forcing rebuild of multiple drives while activity is occurring can have data misdirected to the wrong drive and hit an assertion.(SCGCQ01920097 port of SCGCQ01849986) 
 - FW hit "failed element size check !! ... tail pointer 65535 exceeds max 255" while OCR and rebuilding in loop(SCGCQ01920090 port of SCGCQ01886840) 
 - DDF corruption after hibernation because of incorrect virtual address mappings(SCGCQ01916718 port of SCGCQ01877879) 
 - Firmware ASSERT(SCGCQ01917788 port of SCGCQ01729837 ) 
 - Incorrect clearing of GUID to target ID map table during EPD creation(SCGCQ01920137 port of SCGCQ01909341) 
 - Ventura: In mixed topology, attn LED is non-functional for SAS/SATA drives on OEM backplane(SCGCQ01941124 port of SCGCQ01930666) 
 - CIT: Same EID assigned to 2 930-8i controllers(SCGCQ01892548 port of SCGCQ01830180) 
 - Ctrl fail to response when OCR occur during R6 reconstruction.(SCGCQ01917872 port of SCGCQ01686659) 
 - MCTP: Fault 0x265D when packet with StartOfMsg is set and PktSeqCount is 1(SCGCQ01966451 port of SCGCQ01850721) 
 - Ventura PL: Check in Revised Workaround for 0x5842 fault - Rx Dma Memory Overflow(SCGCQ01967432 port of SCGCQ01864843) 
 - PL : Task management timeout is observed if the task management type is invalid	(SCGCQ01980452 port of SCGCQ01969521) 
 - log dump all command not working on Ventura controllers(SCGCQ01978876 port of SCGCQ01937037) 
 - MR_7.8: During system reboot IMR card logged an event "log discontinuity due to buffer full"	(SCGCQ01978900 port of SCGCQ01872802) 
 - SMP pass through not working when the “PD 0” is BAD drive(SCGCQ01978865 port of SCGCQ01945602) 
 - Remove CSET SCGCQ01961503(SCGCQ01991115 port of SCGCQ01990091) 
 - SLT hangs, when user tries to fetch information about the Bad SAS PD	(SCGCQ01993273 port of SCGCQ01848463) 
 - Data Abort Exception on abrupt powerloss/reset when flushing events from NVRAM hold buffer to flash(SCGCQ01996623 port of SCGCQ01973389) 
 - Data NAK of large master TX packet can stop I2C out of band(SCGCQ01766431 port of SCGCQ01713685) 
 - increase I2C SEP BP command timeout to 3.4s from 600ms(SCGCQ01824063 port of SCGCQ01676712) 
 - Power pull during pinned cache flush leads to unrecoverable pinned cache on subsequent reboot.(SCGCQ01824833 port of SCGCQ01607561) 
 - Enable Personality GET & SET for OEM	(SCGCQ01816865 port of SCGCQ01598867) 
 - 10.2 PKG 1486/ I am able to do a threepass erase using CLI even though this is not supported. HII blocks this action.(SCGCQ01838000 port of SCGCQ01826021) 
 - Ventura: OEM PCIe dual switch attached backplane slot status LED stays Amber on partial slots(SCGCQ01826014 port of SCGCQ01788989) 
 - pl: NVMe: ECF0 fault	(SCGCQ01800735 port of SCGCQ01790929) 
 - (SATA Only(SCGCQ01788567 port of SCGCQ01784132) 
 - PL support for monitoring drive temperature during sanitize operation in progress(SCGCQ01753177 port of SCGCQ01600693) 
 - No AEN showing the firmware booted into HCOE.(SCGCQ01849359 port of SCGCQ01828226) 
 - Ventura: Locate operation to SAS/SATA drive slot may not turn on the status LED on OEM backplane	(SCGCQ01811106 port of SCGCQ01789068) 
 - pl: backend PCIe: port enable may complete before PCIe mode is attempted (part 2	(SCGCQ01794972 port of SCGCQ01727593) 
 - Ventura: OEM ID66 PCIe Switch backplane Slots Status Amber LEDs stay blinking(SCGCQ01772655 port of SCGCQ01687610) 
 - Data NAK of large master TX packet can stop I2C out of band(SCGCQ01766430 port of SCGCQ01713685) 
 - pl: NVMe: unexpected read/write IO failure with SkipCount error(SCGCQ01838023 port of SCGCQ01835109) 
 - pl: Locate LED on SFF-TA-1005 Ux4 backplanes configured in x16 or x8 HFC emulation mode is not activated by storcli command(SCGCQ01873143 port of SCGCQ01866800) 
 - Fault 4311 when running repeated controller resets(SCGCQ01872931 port of SCGCQ01865882) 
 - pl UBM SFF-TA-1005: Locate LED cannot be turned off after diag reset	(SCGCQ01891218 port of SCGCQ01884070) 
 - pl UBM: Locate LED cannot be turned off after diag reset for few drives on Ex1 Elrond(SCGCQ01907168 port of SCGCQ01905070) 
 - ONFI BBL reassignment: COL loop on power glitch during initial COL.(SCGCQ01917764 port of SCGCQ01915345) 
 - Fw hit drvspinup.c when wake up from hibernation	(SCGCQ01925038 port of SCGCQ01912208) 
 - Observed Fatal Firmware Error on Talledega card during SLES 12 O/S installation.(SCGCQ01932019 port of SCGCQ01909779) 
 - IO's can time-out after controller receives an unconfirmed response from a drive	(SCGCQ01926166 port of SCGCQ01878174) 
 - Cannot be done initialize even if execute Full Initialize by using StorCli(SCGCQ01944953 port of SCGCQ01938067) 
 - Firmware hits Kill Adapter when create/initialize R0 VD using 4k drive.(SCGCQ01943907 port of SCGCQ01937998) 
 - Add restriction on personality change requests from RAID to JBOD and JBOD to RAID(SCGCQ01772616 port of SCGCQ01640021) 
 - MR_DCMD_OOB_STATUS_POLL doesn't return any events(SCGCQ01876285 port of SCGCQ01870775) 
 - 530-8i- iMR Controller crashes during IO DMA operation(SCGCQ01917992 port of SCGCQ01830392) 
 - Add the handling of API for discarding all the snapdumps	(SCGCQ01828284 port of SCGCQ01824164) 
 - Unwanted prints removed(SCGCQ01886867 port of SCGCQ01873256) 
 - PD Operations like PD clear and Cryptographic Erase not blocked during personality switch in pending(SCGCQ01891918 port of SCGCQ01889741) 
 - I2C timeout prints seen in TTY log during learn cycle(SCGCQ01824832 port of SCGCQ01807256) 
 - For a bad PD inserted, slot LED does not blink.(SCGCQ01826138 port of SCGCQ01458487) 
 - Unable to turn autoconfig=r0 to autoconfig=off. Giving error message "operation is not possible error 118"(SCGCQ01851702 port of SCGCQ01849199) 
 - During drive spin up, drives come up as 0 bytes	(SCGCQ01961977 port of SCGCQ01944951) 
 - Sotrlci Hide/Unhide command output display incorrect status(SCGCQ01876281 port of SCGCQ01861900) 
 - 9460-8i:"Other Error Count" of drives increase when running dd test	(SCGCQ01965351 port of SCGCQ01943742) 
 - PL Spinup: Firmware Takes a Long Time to Grant Spinup to Some Drives/Phys(SCGCQ01983381 port of SCGCQ01963394) 
 - CSCvc47490 - Often on PD insert PD Fault is asserted,de-asserted	(SCGCQ01957294 port of SCGCQ01332964) 
 - Customer specific back plane not detected in the latest code phase(SCGCQ01972786 port of SCGCQ01961997) 
 - (NVME) Fw Fault (faultcode 0xEC56) hit while performing system reboot test with NVMe drives attached.(SCGCQ01944367 port of SCGCQ01932728) 
 - Data Abort Exception observed while running reboot test with a bad drive.(SCGCQ01995096 port of SCGCQ01985789) 
 - (vSES) Injecting error on I2C channel of one connector module will cause LED of another connector module to not work.(SCGCQ01961503 port of SCGCQ01955094) 
 - Incorrect checks for LD invalid cases during IO processing caused data abort	(SCGCQ01988162 port of SCGCQ01950906) 
 - [vSES] Vendor ID and Product ID of Configuration diagnostic page uses hardcoded values.(SCGCQ01906462 port of SCGCQ01906013) 
 - bounds check not correctly performed on patrol read if media defect exists on the last block of PD(SCGCQ02002681 port of SCGCQ01942077) 
 - Phy Connections count not sent properly to application(SCGCQ02000072 port of SCGCQ01970476) 
 - Data Abort Exception on abrupt powerloss/reset when flushing events from NVRAM hold buffer to flash(SCGCQ01988181 port of SCGCQ01973389) 
 - PL : Task management timeout is observed if the task management type is invalid(SCGCQ01980454 port of SCGCQ01969521) 
 - pl: backend PCIe: additional robustness for hot reset during SAS cycle case(SCGCQ01983403 port of SCGCQ01922270) 
 - Ventura: Use full Slot Cap Physical Slot Number field info for PCIe SW attached device slot enumeration(SCGCQ01941125 port of SCGCQ01936123) 
 - Implement SCGCQ01880847 in MR 7.9: Hit PL Fault 00005862 LinkRegister 01439171 During CC With Triple Media Errors On R60 4K Drives(SCGCQ01935118 port of SCGCQ01909922) 
 - skip the link test if there is no qualifying pd attached	(SCGCQ02029933 port of SCGCQ02018014) 
 - PL vSES: Number of slots for virtual SES is incorrect in StorCLI	(SCGCQ01995099 port of SCGCQ01991774) 
 - Firmware allows to create lower size Dedicated spare compared with the size of the drive part of the Drive Group	(SCGCQ02006215 port of SCGCQ01981279) 
 - Data Abort Exception on abrupt powerloss/reset when flushing events from NVRAM hold buffer to flash	(SCGCQ02000447 port of SCGCQ01973389) 
 - Firmware fault when continuously creating and deleting VDs/EPDs using attached batch script(SCGCQ02001091 port of SCGCQ01864769) 
 - ICMR1 With Storlibtest (OOB(SCGCQ02002112 port of SCGCQ01909345) 
 -(SCGCQ02000768 port of SCGCQ01984675) 
 - The SUT can’t boot to OS after 159 loops AC cycle and check the Raid 930-16i 8G(SCGCQ02000074 port of SCGCQ01788479) 
 - Incorrect checks for LD invalid cases during IO processing caused data abort	(SCGCQ02000917 port of SCGCQ01950906) 
 - MR7.7: Missing diagnostic failed in event log when PD state goes ONLINE to SHIELD and then to FAILED	(SCGCQ02002683 port of SCGCQ01927550) 
 - OCR/KA (if OCR is disabled) occurs when corrupted image is flashed on to a device.(SCGCQ02000479 port of SCGCQ01940516) 
 - ESXi 6.7 does not see JBODs during install or in vSphere.(SCGCQ02036959 port of SCGCQ01994684) 
 - For a specific OEM, in release 10.4, driver detected FW hang during I/O across all RAID levels with different background operations running(SCGCQ02048651 port of SCGCQ02008617) 
 - Secure erase on JBOD drives using hdparam is failing sporadically(SCGCQ02030646 port of SCGCQ01904220) 
 - Foreign status not shown on EKMS drive after runtime key exchange is done(SCGCQ02047749 port of SCGCQ02023636) 
 - SMP pass through not working when the “PD 0” is BAD drive(SCGCQ02030785 port of SCGCQ01945602) 
 - FW hangs at "C0: mapVirtualMemory:" after a power cycle during IO(SCGCQ02035199 port of SCGCQ01971637)
 - Move OCM ECC error scrubbing logic to interrupt context(SCGCQ02030800 port of SCGCQ01970027 ) 
 - Data abort if DevID of SAS PD is sent instead of NVMe PD for NVMe Passthrough(SCGCQ02048643 port of SCGCQ01915272) 
 - 7.9:VSES number of slots are incorrect in StorCLI(SCGCQ02048962 port of SCGCQ01991770) 
 - Host DCDB time out values are getting updated incorrectly(SCGCQ02049503 port of SCGCQ01986878) 
 - MR7.10 Aero Si: Assert Occurs When Migration Completes & VD Goes Missing; I/Os Stop on All VDs(SCGCQ02048712 port of SCGCQ02015773) 
 - Cache Flush Interval can be changed on iMR Controllers.(SCGCQ02034159 port of SCGCQ01988420) 
 - immediate error return from PL not always handled properly(SCGCQ02036594 port of SCGCQ01996107) 
 - Data Abort Exception when Enclosure Status Page has "unrecov" bit set and PDAllowedOps command is issued on the enclosure PD(SCGCQ02038345 port of SCGCQ01968331) 
 - PERC10.4:ONFI: BBLIST RECLAIMALL does not purge factory bad blocks(SCGCQ02035198 port of SCGCQ01978319) 
 - During Firmware update, the message displayed for unsuccessfully updating MegaRAID card will be more descriptive and more compattbile with previous MegaRAID products.(SCGCQ02035204 port of SCGCQ01967058) 
 - Cryptographic Erase operations are blocked for JBODs	(SCGCQ02035369 port of SCGCQ02010293) 
 - Unable to simulate bad flash with LB/LBP on Plumas server(SCGCQ02020100 port of SCGCQ01357295) 
 - All profiles not being enumerated in response to MR_DCMD_CTRL_PROFILE_LIST_GET(SCGCQ02053600 port of SCGCQ01992464) 
 - Handle SMART copy back failures and drive removals gracefully(SCGCQ02012425 port of SCGCQ01867686) 
 - H345 fails to create/delete/edit partitions in Windows on JBOD drive.(SCGCQ02060762 port of SCGCQ01978750) 
 - LSA7.9: When Prepare for removal is performed on all the UG Drives, click on Adv/simple configurations should be grayed out(SCGCQ02052337 port of SCGCQ01968110) 
 - Incorrect SAS address in the timedout event(SCGCQ02060274 port of SCGCQ02031494) 
 - Erase operation is disabled for EPD.	(SCGCQ02062852 port of SCGCQ01937381) 
 - Getting invalid value selecting Manage controller mode in HII(SCGCQ02058098 port of SCGCQ01985983) 
 - After importing a VD with pinned cache, a Consistency Check starts instead of Background Initialization.	(SCGCQ02057457 port of SCGCQ01973185) 
 - PL Fault 00005853, while doing two copyback operations on lds with different block size.	(SCGCQ02034996 port of SCGCQ01970744) 
 - FW reports "Disk test cannot start. No qualifying disks found" during the diagnostics test with multiple drives present(SCGCQ02058013 port of SCGCQ01990513) 
 - Aero - FW returned "can't allocate sufficient mem" when trying to update Intel NVMe drive(SCGCQ02061616 port of SCGCQ02015867) 
 - Disable TransportReady In ICMR1(SCGCQ01838706 port of SCGCQ01828691) 
 - Possibility of data loss due to abrupt/asynchronous warm reset(SCGCQ02007828 port of SCGCQ01985158) 
 - ICMR1 With Storlibtest (OOB) TR can be enabled on VD's it should be disabled(SCGCQ02035781 port of SCGCQ01909345) 
 - Fix the memory allocation issue for diag test(SCGCQ02042675 port of SCGCQ02042041) 
 - Kill adapter issues by driver since Lun Reset hung in Firmware(SCGCQ02021257 port of SCGCQ02005549) 
 - Controller no longer accessible after poweroff and poweron VMware virtual machine (VMware passthrough enabled(SCGCQ02069166 port of SCGCQ02013448) 
 - ModeSelect with ATO field will only be sent to the drive if ModeSense from the drive says the field is changeable.(SCGCQ02065600 port of SCGCQ01979538) 
 - Secure Erase operations are blocked for JBODs on iMR	(SCGCQ02081442 port of SCGCQ01999048) 
 - When discarding a pinned cache and rebooting, discard the cache message observed	(SCGCQ02081443 port of SCGCQ01973033) 
 - EKMS unable to unlock drive - returns key from escrow is invalid	(SCGCQ02082110 port of SCGCQ02063970) 
 - scsi status returned from host and out-of-band storlibtest is wrong	(SCGCQ02081203 port of SCGCQ02051569) 
 - MR_7.9: Snapdump is not triggered in "dmaErrorIsr" Error path.(SCGCQ02066354 port of SCGCQ01989936) 
 - Max number of PDs for PatrolRead to run concurrently should be in range from 1 to MR controller's max configurable PDs(SCGCQ02081309 port of SCGCQ02008420) 
 - Assertion failure in fw\mros\mem.c at line 812: on sending STP passthru from OOB SLT on SATA drive(SCGCQ02081204 port of SCGCQ02050864) 
 - HII menu software was expecting current profile and other compatible profiles to be returned	(SCGCQ02081206 port of SCGCQ02043626) 
 - Critical Message " maximum supported count of 256 disks" received with MaX PDs(SCGCQ02064337 port of SCGCQ01884237) 
 - SATA SSDs are changing to powersave when a warm reboot is issued.(SCGCQ02081205 port of SCGCQ02053087) 
 - Copyback failed on data drive when failed drive inserted back on EKMS encrypted VD(SCGCQ02085508 port of SCGCQ02077226) 
 - Aero A0_Pull/Push Cable caused an assertion with Multipath EPd+R0's	(SCGCQ02085536 port of SCGCQ02048037) 
 - Fault LED of drive doesn't glow intermittently for certain OEM expander systems.	(SCGCQ02096323 port of SCGCQ02011236) 
 - Lenovo 19B: Vses Device Type is displayed as Enclosure for Boynton 8i Board	(SCGCQ02100182 port of SCGCQ02080574) 
 - Aero UTP: Assertion failure during WJ write following a COL event when a VD goes through RLM	(SCGCQ02102489 port of SCGCQ02058372) 
 - Host utils data for Download tty does not match with FW tty buffer dump.	(SCGCQ02127253 port of SCGCQ02123014) 
 - Adapter reset due to an exception(SCGCQ02128228 port of SCGCQ02062791) 
 - iMR: VSAN disk failed and unexpected timeout and phy link errors found(SCGCQ02127914 port of SCGCQ02048151) 
 - Assertion failure during WJ write following a COL event when a VD goes through RLM(SCGCQ02106030 port of SCGCQ02080358) 
 - Previous config missing error during boot after all VDs and JBODs had been deleted in previous boot(SCGCQ02107255 port of SCGCQ02083275) 
 - Slot ID changed from "98:7" to ":255" after issuing PD FW Upgrade command followed by same PD Pull Push(SCGCQ02106028 port of SCGCQ02083026) 
 - TTY logs shows incorrect drive type as 'SATA' for SAS HDD Cryptographic erase.(SCGCQ02106047 port of SCGCQ02100742) 
 - Hotplugging all drives on cascaded backplane config triggers locate/LEDs on a subset of drives(SCGCQ01791034 port of SCGCQ01750103) 
 - MR_EVT_CFG_AUTO_CREATED generated during manual EPD-PT creation(SCGCQ01824932 port of SCGCQ01822271) 
 - Downgrade from 10.2 to 10.1 package should be blocked(SCGCQ01824937 port of SCGCQ01681582) 
 - EPD is created on a different slot then the one specified during creation(SCGCQ01827061 port of SCGCQ01813730) 
 - Forcing personality mode switch is being blocked by patrol read.	(SCGCQ01827067 port of SCGCQ01824760) 
 - When importing VDs in eHBA mode, the target IDs are being assigned with the lowest availabe # instead of the highest.(SCGCQ01791037 port of SCGCQ01753205) 
 - Block setting of personality behavior securesed (on/off	(SCGCQ01791043 port of SCGCQ01787617) 
 - Do not allow to change Auto secure SED in JBOD	(SCGCQ01824060 port of SCGCQ01719271) 
 - Assertion failure in ../../raid/profile.c at line 1381(SCGCQ01824830 port of SCGCQ01760702) 
 - Schedule CC commands are not being blocked with a pending personality change.(SCGCQ01824933 port of SCGCQ01761652) 
 - Controller stuck in current personality if OCR occurs after personality request and before reboot.(SCGCQ01824936 port of SCGCQ01687776) 
 - Ventura MSS: Multi-bit ECC, EFI SAS DRIVER issue seen when performed multi reboot stress from UEFI(SCGCQ01822452 port of SCGCQ01794025) 
 - support to query multibit ecc error by storeliboob(SCGCQ01846010 port of SCGCQ01837670) 
 - dirty led not set on in case of supercap not present even though dirty cache is present(SCGCQ01866206 port of SCGCQ01825031) 
 - Allow firmware download when in JBOD personality	(SCGCQ01824065 port of SCGCQ01618958) 
 - FW state change events are showing s255 instead of the acutal slot number for drives when they are removed.(SCGCQ01824802 port of SCGCQ01715391) 
 - FW is allowing EPD creation when there is pinned cache(SCGCQ01824934 port of SCGCQ01760720) 
 - Decrease SMART Polling Frequency	(SCGCQ01826220 port of SCGCQ01590690) 
 - Dev Defect: Does not allow to downgrade from 10.2 to 10.1 releas	(SCGCQ01742561 port of SCGCQ01729844) 
 - Ventura PL: New HW Workaround for 0x670A Fault	(SCGCQ01842595 port of SCGCQ01841683) 
 - MCTP: 0x265D fault occurs when running high MCTP PCIe VDM load with MCTP Discovery commands(SCGCQ01833182 port of SCGCQ01790303) 
 - [Ventura][PL] TM Hangs when doing drive push pull test case(SCGCQ01817009 port of SCGCQ01792208) 
 - pl: NVMe: Reference Temperature in the Temperature log page is incorrect	(SCGCQ01808970 port of SCGCQ01807465) 
 - MCTP PCIe VDM: controller stops responding after sending over 1000 asynchronous events(SCGCQ01766712 port of SCGCQ01742362) 
 - pl: backend PCIe: debug info for port enable subsystem integration	(SCGCQ01818293 port of SCGCQ01817645) 
 - pl: NVMe: unexpected switch attached task management timeouts(SCGCQ01791046 port of SCGCQ01763332) 
 - pl SFF-TA-1005: All Ux4 drives are not discovered in x8 or x16 HFC mode while hot-plugging(SCGCQ01887446 port of SCGCQ01877041) 
 - Disable Configured Disk Power Saving (DS3(SCGCQ01891921 port of SCGCQ01887503) 
 - Exposing Write cache as disabled to host for a performance improvement(SCGCQ01900924 port of SCGCQ01845298) 
 - 77: FW can not inject Medium error into customer NVMes drive with big size of 4.0Tb(SCGCQ01911910 port of SCGCQ01905236) 
 - CIT: Same EID assigned to 2 930-8i controllers(SCGCQ01886615 port of SCGCQ01830180) 
 - Incorrect vSES Data for Page 0x02 After Storcli Start & Stop Locate Operations for certain NVME Backplanes.(SCGCQ01893314 port of SCGCQ01671177) 
 - Heavy IO with low IO timeout test may result into an IO getting missed.(SCGCQ01840468 port of SCGCQ01631346) 
 - Controller diagnostic test is successful but FW reports LINK test completed 0 passes(SCGCQ01557070 port of SCGCQ01537936) 
 - Coding Standards & Documentation	(SCGCQ01681590 port of SCGCQ01630356) 
 - Implement an additional option to disable “NONE” behavior mode in eHBA personality(SCGCQ01772619 port of SCGCQ01732894) 
 - FW allows creating a VD with 3rd party locked SED drives in eHBA mode(SCGCQ01776323 port of SCGCQ01760656) 
 - Auto-populate ePD-PT name as "NonRaid Disk 'ePD-PT_TARGET_ID'" when it's created	(SCGCQ01824059 port of SCGCQ01732890) 
 - FW is returning extStatus=40 when reading block with medium error(SCGCQ01827065 port of SCGCQ01824741) 
 - EMM 0 removed event displayed during boot on internal active backplane config(SCGCQ01838006 port of SCGCQ01830277) 
 - User unable to switch personality back after a blocked FW update with a pending personality change.(SCGCQ01838008 port of SCGCQ01832472) 
 - Error restoring offloaded (single image controlle(SCGCQ01849356 port of SCGCQ01826923) 
 - Line 535 in ../../raid/cachePreserve.c for trying to create Pinned Cache by Cable Pull.(SCGCQ01849505 port of SCGCQ01839662) 
 - Cryptographic erase operation is failing from Open Manage GUI(SCGCQ01862592 port of SCGCQ01858537) 
 - Change the reserve field in structure mode param to follow spc4 spec	(SCGCQ01868896 port of SCGCQ01816426) 
 - Aero (Talladega) PA3: Controller fail to be detected by BIOS and OS after FW downgrade MR73 with COL(SCGCQ01875268 port of SCGCQ01498117) 
 - Controller can not correctly detected smart error SATAA HDD.	(SCGCQ01881150 port of SCGCQ01506289) 
 - Unnecessary prints logging while issuing DCDB commands(SCGCQ01882466 port of SCGCQ01274681) 
 - Disable - Foreign Auto Import for eHBA personality mode(SCGCQ01824061 port of SCGCQ01718819) 
 - eHBA personality mode event strings needs to be changed from "ePD" to "JBOD" to be in consistent with applications(SCGCQ01824064 port of SCGCQ01640048) 
 - Profile Switching is blocked if configuration is present	(SCGCQ01838004 port of SCGCQ01828959) 
 - On an external controller when selecting Manage Controller Mode, you get a Critical Invalid value message(SCGCQ01849361 port of SCGCQ01830920) 
 - IF “MODE F” successful, then without reboot/OCR application is not showing the updated drive firmware version.(SCGCQ01867241 port of SCGCQ01619555) 
 - 9440-8i / 9460-16i cards BCA_S LED state doesn't match with BCA-S LED Behavior Rule.	(SCGCQ01886610 port of SCGCQ01832279) 
 - pl: NVMe: TransferCount in the SCSI IO error reply message may be invalid(SCGCQ01831794 port of SCGCQ01830303) 
 - Request to harden the SGE / SGL in FW(SCGCQ01824058 port of SCGCQ01760726) 
 - Add maintenance code to avoid incorrect addition of code that can cause MR firmware hang.(SCGCQ01824831 port of SCGCQ01571535) 
 - VD enumeration not consistent in Foreign preview menu in eHBA personality mode.(SCGCQ01851700 port of SCGCQ01828166) 
 - Interrupts not handled in fault state if a high priority interrupt handler faults(SCGCQ01803325 port of SCGCQ01802508) 
 - Unexpected enclosure Fan events seen during physical intervention(SCGCQ01791041 port of SCGCQ01776793) 
 - Dev Defect: DmRecoverMediumErrorPreReadCallback(	(SCGCQ01824938 port of SCGCQ01681553) 
 - Add MR_COL_INFO to NVRAM	(SCGCQ01829242 port of SCGCQ01816715) 
 - SMART Mode is showing as Disabled in eHBA and should be enabled.(SCGCQ01827058 port of SCGCQ01808938) 
 - Retain common PnP IDs for both RAID and JBOD personalities(SCGCQ01824062 port of SCGCQ01684944) 
 - Disable exposeEnclosureDevices in eHBA mode for OEM controllers(SCGCQ01824057 port of SCGCQ01798148) 
 - With multiple locked foreign EPDs and VDs with different security keys, deleting one will no longer show any as Foreign.(SCGCQ01838002 port of SCGCQ01828178) 
 - Aero BST failure, Raid LD tgtId does not persist through OCR	(SCGCQ01876112 port of SCGCQ01857416) 
 - 0x6004 Fault running TM only test(SCGCQ01876864 port of SCGCQ01858982) 
 - pl: vSES reports incorrect product revision level in SES page 1(SCGCQ01883332 port of SCGCQ01877030) 
 - Error notification LED can't be stay long when drive pulled from VD.	(SCGCQ01892583 port of SCGCQ01882216) 
 - Implementation of Degraded media disablement is not working in eHBA mode.(SCGCQ01889448 port of SCGCQ01882573) 
 - Same EID assigned to 2 530-8i controllers(SCGCQ01886617 port of SCGCQ01883096) 
 - Aero PA0.7 - Can't import foreign config (2 pd R0 split across 2 pcie switches(SCGCQ01907155 port of SCGCQ01875226) 
 - MR7.8: CTRL does not detect drives with SAS3.5CtrlFw_Ventura_Ph_9.0 08.250.09.00 and 10 as well(SCGCQ01917864 port of SCGCQ01914192) 
 - PL UBM : SAS, SATA drives in Elrond UBM backplane(SFF-TA-1005(SCGCQ01911215 port of SCGCQ01897599) 
 - Remove BAIL OUT message for successful partial vd creation command(SCGCQ01889455 port of SCGCQ01887298) 
 - Cached Discarded during boot	(SCGCQ01915560 port of SCGCQ01889785) 
 - PL UBM : SAS, SATA drives in Elrond UBM backplane(SFF-TA-1005(SCGCQ01918898 port of SCGCQ01897599) 
 - Incorrect clearing of GUID to target ID map table during EPD creation(SCGCQ01920135 port of SCGCQ01909341) 
 - MR fw doesn't report that SAS_SATA 6 G and 3G capability	(SCGCQ01921441 port of SCGCQ01870194) 
 - Customer specific 3108 PCIe add-on card fails to come back while resuming from sleep state S3(SCGCQ01837506 port of SCGCQ01718911) 
 - Disable ONFI Flash backup of ttylog feature(SCGCQ01914075 port of SCGCQ01906506) 
 - On UG bad PD removal and replaced with UG good PD, iMR allows Vd creation using 33 Pds(SCGCQ01925570 port of SCGCQ01921599) 
 - To support the SEP reset functionality through CPERST in order to avoid warm boot CPLD issues(SCGCQ01851007 port of SCGCQ01765873) 
 - PL needs to check if we have a path to the end device before issuing a device reset to an NVMe drive as a part of TM	(SCGCQ01826239 port of SCGCQ01826234) 
 - Incorrect Element status reported in SES Page 2 by vSES when connected to an expander(SCGCQ01824998 port of SCGCQ01822333) 
 - Aero PA0.7: FW breaks into montask with exceptional core handling error(SCGCQ01855150 port of SCGCQ01850596) 
 - [ventura] PL Fault 0000ecc9 observed, while running doing drive Pull-Push with IO's in background(SCGCQ01829989 port of SCGCQ01804290) 
 - Assertion is hit during region lock release due to inconsistent region lock promotion related variables(SCGCQ01873090 port of SCGCQ01863948) 
 - BIOS Handshake breaks Manufacturing Environment, need change in TTY and/or add timeout in FW for BIOS Handshake(SCGCQ01875086 port of SCGCQ01575182) 
 - Dev Defect: GUID target ID map table is Invalidated on Insertion of off-lined drives	(SCGCQ01862595 port of SCGCQ01859088) 
 - Fix BST Scripts to Account for New Allowed UART Logs	(SCGCQ01855060 port of SCGCQ01849765) 
 - pl UBM: Ux4 drives not discovered in Polling Mode with HFCx16 and x8	(SCGCQ01906082 port of SCGCQ01896578) 
 - pl: NVMe: SCSI log page temperature may be incorrect in some cases(SCGCQ01807316 port of SCGCQ01804437) 
	
EnhancementRequest:	
 - Aero/Ventura: Create a build environment in the SPI_LIBRARY component(SCGCQ01819132) 
 - Aero3: Integrate sasparser 11.02.00.00 into Aero build process(SCGCQ01851153) 
 - Aero-3: Add securesign to build process of full firmware image(SCGCQ01509968) 
 - Aero: Add checking of secure main firmware (APP(SCGCQ01856978) 
 - SFF-TA-1005 UBM: Additional error handling support(SCGCQ01833053) 
 - MR API changes to support EKMS over OOB(SCGCQ01874035) 
 - RTTrace Enable/Disable API changes(SCGCQ01830211) 
 - API change to support new DCMD for consolidated device list(SCGCQ02016723) 
 - API Changes for Driver/FW DCMD HandShake	(SCGCQ01841266) 
 - Added new events for unmap policy changes(SCGCQ01871912) 
 - Add secure boot key update complete event(SCGCQ01928254) 
 - Add CTRL_SB_SOFT_SECURE_MODE event to indicate soft secure mode(SCGCQ01965721) 
 - Add a new log event used whenever the snap dump properties are modified.(SCGCQ01963328) 
 - Modification in MR_SNAPDUMP_TRIGGER_TYPE enum value	(SCGCQ02030653) 
 - Customer needs to generate and extract the On-demand based debug data both for MR and iMR.(SCGCQ02000566) 
 - [MR 7.8] API change to return apt failure status for a personality change request	(SCGCQ01853480) 
 - RMC: Force RMC to be built when main firmware images are built.(SCGCQ01807469) 
 - Ventura: Support for IOP direct access of ISTWI devices that are not specified in Man page 43(SCGCQ01750098) 
 - Enable SRIS to enable external NVMe capability(SCGCQ01807622) 
 - Add nvmeProtocol.h to MR PL release(SCGCQ01837309) 
 - NVMe: SFF-TA-1005 UBM PCIe Power Management support(SCGCQ01763350) 
 - pl: backend PCIe: ordered event handling for cascaded switches(SCGCQ01850742) 
 - Ventura: Improve verbose "pl mids" output(SCGCQ01863333) 
 - aviSerdesGenericSpicoEccCheck((SCGCQ01807158) 
 - HDET: Support smp passthrough storeliboob (API changes requirement(SCGCQ01916035) 
 - Interrupt coalsecing setting per group of 8 replies queues (h/w VF registers(SCGCQ01886424) 
 - ComboSerdes: add API function to wait for SAS to PCIe transition to complete(SCGCQ01928060) 
 - Add secure boot support	(SCGCQ01792416) 
 - API change to provide learn complete timestamp(SCGCQ01845269) 
 - Aero FW - Reporting SSD wear gauge values for OEM specific customers(SCGCQ01798686) 
 - Add the API to clear all the snap-dumps from firmware.(SCGCQ01824135) 
 - Add new MFI Status - MFI_STAT_PD_NOT_ELIGIBLE_FOR_LD	(SCGCQ01818580) 
 - Aero-3: New CSW / 16FF Serdes(SCGCQ01448312) 
 - SPI Flash Suspend/Resume feature support.(SCGCQ01735536) 
 - Tune DDR settings for OEM's custom design(SCGCQ01898339) 
 - Removing the unwanted debug prints(SCGCQ01896349) 
 - Allow unmap after FW downgrade but till reboot is done(SCGCQ01837980) 
 - Update Channel board NVDATA to include info for automation of HwBoardImageConfig creation(SCGCQ01803280) 
 - Update temperature sensor output	(SCGCQ01616949) 
 - Aero-3: Check Completor Posted Writes and Requestor Posted Writes bits in FPE Status 1 in determining Idle	(SCGCQ01824153) 
 - Aero: Get FPGA to scheduling loop(SCGCQ01766800) 
 - Ventura: Eliminate need for IOPRINT_X_DEFAULT_08X(SCGCQ01488980) 
 - Ventura: Integrate SPI_LIBRARY project build system to the IT firmware(SCGCQ01680530) 
 - Aero3: Create Aero3 non-FPGA nvdata	(SCGCQ01764985) 
 - Aero: backend PCIe: Downstream Port Containment(SCGCQ01828062) 
 - SPI_LIBRARY: Modify the component so that the basetypes file is optional	(SCGCQ01827876) 
 - ISTWIToolBox command handling using parameters passed in from the host(SCGCQ01824007) 
 - pl: backend PCIe: change the Predetermined Number of Lanes setting to 1(SCGCQ01784774) 
 - Aero: backend PCIe: Gen4 hardware and device init(SCGCQ01380060) 
 - Aero: backend PCIe: root port 16GT/s lane equalization(SCGCQ01614673) 
 - SFF-TA-1005 UBM: Backplane change detection polling mode support	(SCGCQ01727552) 
 - SFF-TA-1005 UBM: UBM HFC RefClk control, DFC drive presence detection and Port Reset control	(SCGCQ01750204) 
 - pl: backend PCIe: runtime control of Atlas switch support (part 2(SCGCQ01853888) 
 - pl: Aero: remove Atlas 32-bit address space workaround	(SCGCQ01763386) 
 - SFF-TA-1005 UBM: UBM backplane CHANGE_DET# Signal Interrupt support(SCGCQ01727480) 
 - support to query multibit ecc error by storeliboob(SCGCQ01837670) 
 - Perform prefill check of on-chip memory copy for offload	(SCGCQ01828066) 
 - Improve how FW validation stamp is checked/used	(SCGCQ01868013) 
 - Add support to identify the presence of the switch in 7.8(SCGCQ01851716) 
 - DDR tuning parameters based on subOEM ID	(SCGCQ01964424) 
 - Disable unmap feature on R5/6 only(SCGCQ01985917) 
 - Add new MFI Fault sub code for Secure Boot Preboot Auth failure(SCGCQ02006657) 
 - Porting MR on-demand snapdump support from MR 7.9 to Lenovo 19B stream(SCGCQ02032636) 
 - LDET Q32018 - RRB130 - Enable iMR advanced debug dump to ttylog(SCGCQ02034476) 
 - LDET Q32018 - RRB130 - Enable MR advanced debug dump	(SCGCQ01873123) 
 - Fix MR_CTRL_INFO to support backward compatibility(SCGCQ01946548) 
 - Add New Generic OOB API To Read ROC Temp, Drive Temp, Drive Type, Drive Protocol and status through OOB BMC(SCGCQ01940661) 
 - [MR 7.8] API change to export "disable least latency mode"(SCGCQ01887495) 
 - Add entry for DST_PD_EPD_NVRAM in Nvram dynamic section.	(SCGCQ01807468) 
 - Add MR_COL_INFO to NVRAM	(SCGCQ01816715) 
 - Updating the Aero version of NVRAM(SCGCQ01797927) 
 - Max IO size set same value as JBOD and Single drive R0(SCGCQ01819147) 
 - Aero: backend PCIe: support for Atlas physical slot numbering(SCGCQ01845211) 
 - Added pmuMsg.h file to project.	(SCGCQ01832975) 
 - Ventura: Make SGPIO as vSES default backplane mgmt. method(SCGCQ01792989) 
 - Aero DDR: Software based Read Fifo(SCGCQ01767237) 
 - PL SATL: RC BASIS Handling for SCSI Read Capacity 16 for SMR SATA drives(SCGCQ01615537) 
 - Aero-3: Update Copyright to Broadcom	(SCGCQ01732998) 
 - Aero-3: Add support for MCTP Discovered Flag clearing due to BDF change(SCGCQ01533535) 
 - Aero-3: Update CCR headers to reflect latest register map.(SCGCQ01826405) 
 - Aero: backend PCIe: basic Atlas validation board bringup	(SCGCQ01794264) 
 - Aero DDR: PHY based Gate Training(SCGCQ01405423) 
 - Aero-3: Create Temporary IT Release Script(SCGCQ01837898) 
 - Aero: Update CSW M0 firmware	(SCGCQ01828153) 
 - pl: NVMe: tweak NVMe temperature threshold configuration	(SCGCQ01808996) 
 - Misc changes for CHANGE_DET# Signal Interrupt and drive hot-plug support(SCGCQ01797168) 
 - Aero: pl: protocol cycle detector support for Aero(SCGCQ01794128) 
 - Aero DDR: Software based Write Leveling Cycle Adjustment	(SCGCQ01405431) 
 - To do dynamic configuration of the PCIe link from the backplane configuration data(SCGCQ01507511) 
 - I2C BUS busy when BMC try to access other devices on the bus with MCTP disabled.	(SCGCQ01697892) 
 - Added customer serial number field to MFC Manufacturing 2 structure(SCGCQ01873417) 
 - Add learn complete timestamp in NVRAM struct	(SCGCQ01845275) 
 - Added NVRAM dynamic section for persisting PD information specific to Hercules(SCGCQ01833482) 
 - FW additional changes for mixing Rules for SED and non-SED drives with controller security enabled.(SCGCQ01839851) 
 - Integrate RMC Logs into Snapdump, Collect snapdump for cache offload failures(SCGCQ01856131) 
 - Unmap policy change in 7.8	(SCGCQ01870855) 
 - Aero-3: IOP: Host PCI Express 4 x8 interface(SCGCQ01380006) 
 - pl: backend PCIe: Atlas base mode duplicate serial number handling(SCGCQ01819242) 
 - Aero DDR: Clean up Aero DDR lib(SCGCQ01789017) 
 - Implement MR FW support to capture Windows Driver log and add to SnapDump.(SCGCQ01818505) 
 - Added new megamon method to inject medium error	(SCGCQ01842589) 
 - pl: backend PCIe: immediate retry of firmware initiated PCIe transactions during link recovery(SCGCQ01841059) 
 - NVMe Devices added to Inventory and support for NVME AEN	(SCGCQ01607921) 
 - Enable/Disable debugDynamicmemory flag based on the release type stamping(SCGCQ01865881) 
 - Add a bit for atomic descriptor capable(SCGCQ01965047) 
 - Added Support for Triggering SnapDump(SCGCQ01848759) 
 - Change JBOD profile ID to support 240 VD	(SCGCQ01733235) 
 - Prepare the NVDATA for first Release for 7.8 program.(SCGCQ01858938) 
 - Add proof that A15 L1/L2 flush occurs(SCGCQ01816577) 
 - Changing LDBBM setting (Wingman medium error issue(SCGCQ01857308) 
 - Move NVRAM hibernation signature definition to NVRAM header file	(SCGCQ01886892) 
 - Add Board Support Package Image Type to MR_IMAGE_TYPE(SCGCQ01931637) 
 - pl: backend PCIe: add switch count to Manufacturing Page 9(SCGCQ01851624) 
 - Add debug prints and dump for new serdes	(SCGCQ01831104) 
 - RMC: Remove old RMC binary from version control	(SCGCQ01817562) 
 - Initial version of PSOC programming code	(SCGCQ01794157) 
 - SFF-TA-1005 UBM - FRU device detection and FRU Record processing support	(SCGCQ01727443) 
 - NVRAM changes to store controller PCI slot and server serial number	(SCGCQ01864509) 
 - Add a new MR FW AutoBST test for UNMAP	(SCGCQ01830386) 
 - Modify DDR frequency for OEM ROMB design	(SCGCQ01871283) 
 - Add support for configuring PCA9555 IO expander for OEM VPP compatible backplane.(SCGCQ01807461) 
 - SFF-TA-1005 UBM: Drive Slot status LED control(SCGCQ01727586) 
 - New unmap policy	(SCGCQ01867056) 
 - Ventura: Modify PL to only allocate required config page buffer size	(SCGCQ01817424) 
 - Ventura/Aero: Implement Extended Mfg Page 45 - Aladin Config Page - Implement Aladin Init(SCGCQ01680543) 
 - SFF-TA-1005 UBM: UBM Controller enumeration support(SCGCQ01727463) 
 - API changes for Lane Margining(SCGCQ01921241) 
 - Introduced new controller bit(SCGCQ01985474) 
 - Driver parameter bit for support of tool box cmd	(SCGCQ02002119) 
 - PL: Add Nvdata Option to Disable SPL-2 Power Capable Spinup(SCGCQ01823993) 


Version 50.7.0-2054- Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS: 7.07.00.1
	UEFI Driver: 0x07070301
	HII:  07.07.05.02
	MR FW: 5.070.00-1916
    package 50.7.0-2054

MR 7.7
	
Defects:
 - Marlin RMC: Fix checking of cores in reset during ChipReset sequence.(SCGCQ01197528) 
 - (SATA Only) Security Protocol In command complete without data transfer for allocation length not a multiple of 512.(SCGCQ01275335) 
 - Charlotte DVT (3616) - Fails PCI Express Compliance Configuration Test.(SCGCQ01320438) 
 - Enable WB support via API.(SCGCQ01405242) 
 - Aero : Assertion failure in fw\raid\mpthostcmd.c at line 2106: when run I/O overnight with NVMe drive.(SCGCQ01453837) 
 - Aero : Assertion failure in fw\cpu\arm\exceptions.c at line 938 when boot to OS with large config.(SCGCQ01455668) 
 - Ventura scatter file loads wrong via file(SCGCQ01471160) 
 - Correct preinclude dependencies.(SCGCQ01472945) 
 - Aero (Talladega) PA1: Assertion failure in fw\raid\taskman.c at line 328 during IO, consistency check.(SCGCQ01473856) 
 - Revert changes from SCGCQ01458368.(SCGCQ01484285) 
 - Ventura: MCTP PCIe VDM: Discovered flag is set in Endpoint Discovery command.(SCGCQ01486410) 
 - The soft FIFO size calculations don't take into account the data descriptor sf threshold.(SCGCQ01488633) 
 - Controller is not detecting in the storelib, after changing the mode from "set mode oob" command.(SCGCQ01494018) 
 - Correct Aero dependency issue(SCGCQ01495441) 
 - pce.c warnings.(SCGCQ01497808) 
 - Check the use of the LD BBM already tried flag.(SCGCQ01497811) 
 - TOOD AS - For Skinny running out of memory need some optimization to be done.(SCGCQ01497817) 
 - 2nd arg passed in is not what the function is expecting, fix it.(SCGCQ01497819) 
 - Reevaluate commented cache code.(SCGCQ01497856) 
 - Move RDM buffer functions to DM layer.(SCGCQ01497876) 
 - PL: Update internal macros.(SCGCQ01503214) 
 - Ventura build failure.(SCGCQ01505238) 
 - Error if PERL_DIR environment variable is set(SCGCQ01506708) 
 - FW to return the MFI_STAT_OPERATION_NOT_POSSIBLE, when RAID Level change is not supported by FW(SCGCQ01507208) 
 - Fix MPT_BuildNVMePRPfromSGL(SCGCQ01507527) 
 - RMC: Prevent leakage of P credits during SoftReset(SCGCQ01507699) 
 - Fixed IOP coverity defect for intruder(SCGCQ01508917) 
 - PL: Fault 0x5862 seen when host buffer size is smaller than allocation length in CDB.(SCGCQ01509770) 
 - Merge error in pceErrorInt(SCGCQ01509973) 
 - Fault 0xC00C is occurred in random read running test(SCGCQ01511237) 
 - Check if PrpDmRecoveryCheckIsPrp/DmRecoveryCheckIsPrp needs to be fixed(SCGCQ01511911) 
 - pl: backend PCIe: 4311 fault with NVMe enabled(SCGCQ01514521) 
 - Ventura hardware does not like the IOP enable method used here.(SCGCQ01514880) 
 - (SATA Only) LBPRZ bit in VPD page 0xB2 is never set for SATA devices(SCGCQ01516277) 
 - stack overflow during I2C read operation(SCGCQ01516908) 
 - pl: backend PCIe: non-NVMe endpoint not cleaned up on removal(SCGCQ01516968) 
 - Fault(0x4330) is occurred during checking MPI2_IOCSTATUS_TARGET_TOO_MUCH_WRITE_DATA.(SCGCQ01518952) 
 - Hex dump of RMC ring buffer is only showing one entry.(SCGCQ01519272) 
 - [OOB]RMC/MR Crash Due to PCE Core Register Access Errata during vSAN certification Test.(SCGCQ01521255) 
 - Fixing the issues during bringup of the universal backplane.(SCGCQ01522148) 
 - pl: backend PCIe: switch attached discovery takes too long.(SCGCQ01522343) 
 - pl: backend PCIe: 4311 fault with NVMe enabled (part 2)(SCGCQ01523531) 
 - Ventura: Add early notification to new I2C-DMA-Less algorithm in case hardware doesn't interrupt.(SCGCQ01524953) 
 - MR 7.6: Opal: Fix compilation error (SCGCQ01525448) 
 - pl: NVMe: PCIe reconfiguration may occur during NVMe controller reset (SCGCQ01526236) 
 - gas gauge device chemistry check(SCGCQ01526260) 
 - Handling of host PCI BAR programming changes after port enable(SCGCQ01530295) 
 - pl: NVMe: EC0D fault(SCGCQ01530402) 
 - PL Fault 0000ecdd LR 01403837 during initial discovery(SCGCQ01531770) 
 - Secure erase failure	(SCGCQ01531846) 
 - To fix issues for back plane configuration validation and LED control for the UBM backplane.(SCGCQ01533852) 
 - Ventura: Some toplevel PCE interrupts have a priority that is too low(SCGCQ01534773) 
 - pl: backend PCIe: 4311 fault (part 3)(SCGCQ01537791) 
 - After setting DGs to TR storCLI does not show DG status as TR.(SCGCQ01537949) 
 - pl: NVMe: unexpected task management halt when a device goes missing.(SCGCQ01538012) 
 - Fault 5850 occurred in random read test with Task management.(SCGCQ01538680) 
 - MR 7.6 - NVMe drive reported "Unable to access device PD xx" after reinserting.(SCGCQ01538713) 
 - pl: backend PCIe: link workaround not sufficiently coordinated with SAS link establishment(SCGCQ01540226) 
 - Aero : Continous error( MptHostCmdDone cmdId=fe lmid=8a2:1851b400 tid 04 devH ..	.(SCGCQ01540433) 
 - Ventura B0: FW blocking SATA devices behind enclosures(SCGCQ01552996) 
 - (SATA Only) Incorrect sense data may be returned when a NCQ Queued Error Log data page is returned.(SCGCQ01553853) 
 - pl: backend PCIe: tweaks to the backend PCIe link configurations API.(SCGCQ01556422) 
 - Correct minimum voltage calculation of Supercap.(SCGCQ01558901) 
 - MR7.6: Enclosure no longer seen on OS level after cable pull.(SCGCQ01562109) 
 - TUR and SSU was being issued to the drive when Task Management is underway.(SCGCQ01562717) 
 - IT/PL FW Compliance to use of NO FLUSH bit in START STOP UNIT based on SAT3.(SCGCQ01563244) 
 - pl: verify that RAID context Timeout value is nonzero before adding a timer.(SCGCQ01564757) 
 - LED won't blink after setting DGs to TR in OEM system; other OEM system work(SCGCQ01565718) 
 - The timer values used in case of PD firmware download is not as per design. (SCGCQ01565780) 
 - pl: NVMe: admin command Abort Task reset type(SCGCQ01565972) 
 - Issue: JBOD devices were dropped after unloading driver and reloading driver in linux(SCGCQ01566087) 
 - pl: backend PCIe: 'pl pci swregs' debug command is broken(SCGCQ01566859) 
 - MR 7.6 PA2: Creating RAID 1 or RAID 6 array with Dedicated Hotspare bails out at line 2457 cmdStat=4e(SCGCQ01570697) 
 - MR 7.5 Alpha-Beta_Ventura:Perf drop of R0,R1,- 5% to 7% is seen in SW IO Size-4K-32K,QDs (1,4,16,64)(SCGCQ01571858) 
 - Ventura B0 Phase 7 - Fault 2805 hit after enabling auto port feature(SCGCQ01572362) 
 - To fix the LED issue, VPP data and moving to change detect poll state (SCGCQ01576165) 
 - (SATA Only) SCSI Write Long command send with out of range block address does not fail.(SCGCQ01577907) 
 - Fix OCM copy when no dirty cache	(SCGCQ01586776) 
 - ignore64ldRestriction set incorrectly causes MR_DCMD_CFG_READ to fail(SCGCQ01587700) 
 - Aero PA4.5: FW waiting for BAR Init to complete indefinitely after each OS reboot. (Proprietary PCI-E riser(SCGCQ01588734) 
 - MR7.6 storelibtest see incorrect enclosure slots count plus show device id0 twice(SCGCQ01589027) 
 - Assert when the Nvdata connector names mismatch from the MfgPage0 and ManPage7 (SCGCQ01590427) 
 - pl: vSES - Enable Swap bit support in SES page 2 (SCGCQ01590780) 
 - OEM card running 7.6 code had two regions of flash defined did not bootup after FW upgrade and powercycle(SCGCQ01592585) 
 - MR7.6:Assertion failure in ../../dma/dmaxor.c at line 1190:(retVal == SYS_DMA_STATUS_SUCCESS(SCGCQ01593643) 
 - MR7.6: Rolling message MemPoolAlloc() failed - tag="LDRMAP", size=0x17f10 (98064) failed count in last 5 seconds (0)(SCGCQ01593740) 
 - Several firmware build utilities don't compile anymore(SCGCQ01594270) 
 - iMR6.7-9440-16i: Hit Assertion failure in ../../cpu/arm/exceptions.c at line 938: 0 After loading the driver & reboot system.(SCGCQ01594719) 
 - while creating filesystem on UNMAP supported vd's and running CC in back ground will result in montask in rhel6.9.(SCGCQ01598653) 
 - NVDATA for iMR has maxChainedEnclosures set to 10; should be set to 2.(SCGCQ01598760) 
 - FW should block EPD-PT devices in JBOD to RAID personality if MFCD.enableJBOD is 0 to avoid data loss.(SCGCQ01599680) 
 - Enclosures is not exposed to Host even if exposeEnclosureToHost is set.(SCGCQ01599832) 
 - Observed Exception during Test run: IocStatus: Insufficient Resources (0006)(SCGCQ01600177) 
 - Task Management due to SATA init failure results in resource error message(SCGCQ01605610) 
 - CfgDumpAutoConfigInfo build failure(SCGCQ01614684) 
 - Fixing skinny compilation error(SCGCQ01614967) 
 - Aero - C0:Assertion failure in fw\cpu\arm\exceptions.c at line 940: 0(SCGCQ01618680) 
 - isValidSnapDumpPresent() was in VIRTUALADDR_DDR_CODE and was being called before code sections was loaded.(SCGCQ01618950) 
 - Firmware Build Utilities: AddImage utility gets flagged and removed by anti-virus software(SCGCQ01619096) 
 - Fault 0000d075 LR 043e158d during 48 hours Controller resets with and without Battery(SCGCQ01620516) 
 - Aero PA 0.45: PD went from ONLINE to SHIELD state During Multiple path cable push pull.(SCGCQ01620847) 
 - pDevInfoExt->dismCmdFailDone always stays on.(SCGCQ01623890) 
 - Aero - PL Fault 00006001 LinkRegister 04330b07(SCGCQ01627081) 
 - Ventura: Build time duration started displaying negative time.(SCGCQ01630393) 
 - MR7.7 FW returns error if StorCLIO/StorCLIF changes default value of parameter enable FDE type mix.(SCGCQ01630843) 
 - [MR7.5] Rebuild Progress 0 % logged just after OS reboot during rebuild running.(SCGCQ01631496) 
 - Controller level bit for unmap should be always enabled for 7.6.(SCGCQ01631828) 
 - DHSP are not spun down when Disk Group is set to TR.(SCGCQ01634034) 
 - Revertible HSP is not reverted back on Clear TR.(SCGCQ01634752) 
 - MR 7.6 - "NVCache has gone bad" during POST after flashing the latest package 1226 and rebooted.(SCGCQ01635062) 
 - : FW asserts when invalid parameters to set excluded ld for CC is sent to firmware.(SCGCQ01635729) 
 - Remove redundant defines.(SCGCQ01635739) 
 - After FW update, controller was not reset by the OCR command, and if user retries the command, then FW hits the exception.(SCGCQ01639394) 
 - ExtManPage40 FeatureFlags bit definition is missing in 9405W-16i partinal NVDATA.(SCGCQ01639482) 
 - Firmware downgrade policy with secured OPAL FDE Drives.(SCGCQ01639904) 
 - MR7.6 Fix up NAND Flash Chip Model Number read from device has bad crc.(SCGCQ01640081) 
 - Disable the iMR FP IO Fine tuning changes.(SCGCQ01641453) 
 - pd.c: Correct logical error in deciding whether to allow (or not)(SCGCQ01665122) 
 - Data Corruption seen on NVME drives with Medium Errors.(SCGCQ01665227) 
 - Not to do all drives reset at the start of the boot up on each port of the controller.(SCGCQ01670965) 
 - Not able to set max no of PD using set patrol read properties in LSA/Storcli.(SCGCQ01671189) 
 - Can't instant secure erase drive vendor specific SATA OPAL drives.(SCGCQ01675808) 
 - Missing code to handle no response in MCTP transmit buffer and send busy retry.(SCGCQ01676010) 
 - ONFI initialization failure on some DVT boards.(SCGCQ01676782) 
 - Inconsistent CC progress % is logged after reboot during CC.(SCGCQ01683057) 
 - Aero RMC: Fix non-secure boot mode.(SCGCQ01683135) 
 - MR7.7: Locate PD/LD on SGPIO, is not working.(SCGCQ01683164) 
 - Ensure that chip specific code is included.(SCGCQ01683240) 
 - pl: NVMe: unnecessary SATA cleanup attempted during NVMe TM.(SCGCQ01683245) 
 - ExtManPage40 FeatureFlags bit definition is missing in 9405W-16i partinal NVDATA.(SCGCQ01684262) 
 - Mercator: AHR failure when using workaround for SCGCQ01318807.(SCGCQ01685001) 
 - Assertion failure in pceBarUpdateIsr (ISR where FW samples the BAR addresses. (SCGCQ01685126) 
 - Ctrl fail to response when OCR occur during R6 reconstruction.(SCGCQ01686659) 
 - Enable debugDynamicmemory until Beta.(SCGCQ01697591) 
 - [iMR7.5] Memory allocation failure during RAID operation cycles under high loading.(SCGCQ01697700) 
 - vSES not handled correctly for auto rebuild.(SCGCQ01698371) 
 - Too many Unexpected Sense : "1/0/1d " logged for SATA drives.(SCGCQ01714261) 
 - Continuous firmware event when run I/O on EPD NVMe ( MptHostCmdDone cmdId=86 lmid=42d:1859a000 tid 04.(SCGCQ01714573) 
 - Eliminate SGPIO add in presence of VSES.(SCGCQ01714777) 
 - MR7.7: Firmware does not allows user to import VDs created in MR 7.5.(SCGCQ01715014) 
 - PL: Chassis Slot Valid Flag is Incorrectly Cleared in Enclosure Page 0.(SCGCQ01715509) 
 - Cannot stop patrol read on PD with medium errors by the stop cmd.(SCGCQ01715992) 
 - Patrol read restarts on PDs after completion on reboot.(SCGCQ01718200) 
 - Aero PA0.5: FW auto configure EPD drives to ONLINE upon insertion when FW is in Safe Mode.(SCGCQ01718871) 
 - Write journal failure wjProcessJournalEntries: failing the entry: Index: 4f53, cacheline: 46a7.(SCGCQ01718922) 
 - MR7.7: Firmware does not convert WT-CIO VDs to WT-DIO VDs when upgrade to MR 7.7 firmware.(SCGCQ01719309) 
 - pl: backend PCIe: port enable may complete before PCIe mode is attempted (part 2	.(SCGCQ01727593) 
 - pl: backend PCIe: notification events for switches with no devices attached(SCGCQ01729831) 
 - When patrol read completed with Talladega 9460-8i and MR7.5 components, the customer saw Patrol read complete events were log(SCGCQ01732235) 
 - Ventura: CFGI fails if the largest MPI defined config page is not included(SCGCQ01737603) 
 - Invalidate pd slot at SOD(SCGCQ01747219) 
 - Aero build fails(SCGCQ01748072) 
 - Fatal firmware error: Line 144 in fw\raid\utils.c (SCGCQ01753351) 
 - Import config failed ( DDF_ConfigReadPd: pdCOD->cfgErrStatus 16(SCGCQ01753383) 
 -(SCGCQ01753405) 
 - Aero PA0.5: Assertion failure in fw\cfg\cfgisup.c at line 3885: wIndex==0(SCGCQ01762118) 
 - BMC emulator does not load storelibTest(SCGCQ01762267) 
 - Updated behavior as requested(SCGCQ01762855) 
 - Flashing AERO Package on Brand new controller and observed Assertion in gpio_get_output_mode on Reboot.(SCGCQ01763311) 
 - MR7.7: FW hit Assertion failure in fw\raid\mpthostcmd.c at line 1951: DMGetSpanFromDevhandle(pMpt->DevHandle(SCGCQ01763331) 
 - pl: NVMe: unexpected switch attached task management timeouts(SCGCQ01763332) 
 - iMR controller with direct attach SATA drives did not show enclosure ID ( 7.6 is OK )(SCGCQ01764496) 
 - EPD JBOD became foreign after it was locked by third party security software	(SCGCQ01765156) 
 - SGL frame resource leak during handling of NVMe R/W cmds diverted to FW(SCGCQ01767166) 
 - Check PRP functions for 1 MB IOs and make sure prpCount variable size is good enough(SCGCQ01776107) 
 - Ventura B0: 0x5842 fault while running IOs and error injection tests(SCGCQ01780777) 
 - (SATA Only) Sense descriptor not filled properly for SCSI ATA Passthrough command failed by drive with SDA bit set.(SCGCQ01784132) 
 - In the Ld snapdump, LdDumpTgtIdInfo using ld as index, which should be tgtid.(SCGCQ01786599) 
 - MR 7.7 - AddConfig : ProcessLibCommandCall failed ; rval = 0x1 while creating/adding a config(SCGCQ01788489) 
 - fix the snapdump zip file which has mismatched filenames and content.(SCGCQ01789699) 
 - pl: NVMe: ED8D fault related improvements (SCGCQ01789903) 
 - Ventura B0: Controller fault 0x7C41 observed during IO+System power cycle test(SCGCQ01790305) 
 - snapdump files are generated regardless of snapdump state(SCGCQ01790857) 
 - pl: NVMe: ECF0 fault(SCGCQ01790929) 
 - Kill adaptor during heavy IO run(SCGCQ01792088) 
 - Can't import foreign configuration with Enterprise and Opal secured VD (R0)(SCGCQ01792749) 
 - Add validData variable in to NVRAM.h	(SCGCQ01793953) 
 - remove unnecessary code and comments starting with developer's name(SCGCQ01799276) 
 - PL SATL: SANITIZE Command failing for SATA SMR drives with ZNR bit set(SCGCQ01800567) 
 - fw hit ddfconfig.c when insert the cable back enclosure.(SCGCQ01802513) 
 - Aero PA0.6: OCR occurred during copyback on a bad SATA SSD EPD(SCGCQ01804216) 
 - MR FW may return successful completion on host Rd cmd to EPD when the device is removed.(SCGCQ01804389) 
 - pl: NVMe: SCSI log page temperature may be incorrect in some cases(SCGCQ01804437) 
 - Too many lines of type "msixIdx:1f replyDescConsPtr =10-3190dfe8 replyIdx ..." in FW log when forcing a KA(SCGCQ01807325) 
 - fixed exception at medium error recovery caused by a bad drive.(SCGCQ01807457) 
 - pl: NVMe: Reference Temperature in the Temperature log page is incorrect(SCGCQ01807465) 
 - Controller hits KA because cmdblock does not complete due to pending flush.(SCGCQ01807618) 
 - Fixed merge issues.(SCGCQ01813889) 
 - Change the reserve field in structure mode param to follow spc4 spec(SCGCQ01816426) 
 - Firmware hit mem.c monstak when change from RAID mix mode profile 13 to JBOD personality(SCGCQ01817505) 
 - Disallow unmap operations for EPDs(SCGCQ01817555) 
 - pl: backend PCIe: debug info for port enable subsystem integration(SCGCQ01817645) 
 - Incorrect Element status reported in SES Page 2 by vSES when connected to an expander(SCGCQ01822333) 
 - dirty led not set on in case of supercap not present even though dirty cache is present(SCGCQ01825031) 
 - PL needs to check if we have a path to the end device before issuing a device reset to an NVMe drive as a part of TM	(SCGCQ01826234) 
 - CIT: Same EID assigned to 2 930-8i controllers(SCGCQ01830180) 
 - pl: NVMe: TransferCount in the SCSI IO error reply message may be invalid(SCGCQ01830303) 
 - 9440-8i / 9460-16i cards BCA_S LED state doesn't match with BCA-S LED Behavior Rule.(SCGCQ01832279) 
 - pl: NVMe: unexpected read/write IO failure with SkipCount error.(SCGCQ01835109) 
 - Fix to CSET SCGCQ01605489.(SCGCQ01837880) 
 - Red/Amber LED Says On Solid During NVMe SSD Rebuilds & Does Not Turn Off When Rebuild is Completed.(SCGCQ01837894) 
 - Issue: Megamon commands from MEGAMON_DCMD were not executed properly by firmware.(SCGCQ01838863) 
 - Ventura PL: New HW Workaround for 0x670A Fault(SCGCQ01841683) 
 - Incorrect target ID allocation in JBOD personality(SCGCQ01845282) 
 - MR7.6 and MR7.7 Latest ROPs failed to Flash on OEM board results in "CRC of the copied (SBR)(SCGCQ01849017) 
 - Block firmware downgrade from MR 7.7 to older ROP if users are using NVMe switch since the feature only support 7.7 and up (SCGCQ01851533) 
 - Ventura: Attaching multiple PCIe switches may cause IOP memory corruption (SCGCQ01853893) 
 - 77: FW can not inject Medium error into customer NVMes drive with big size of 4.0Tb(SCGCQ01905236) 
 - MR7.7: Missing diagnostic failed in event log when PD state goes ONLINE to SHIELD and then to FAILED(SCGCQ01927550) 
 - FW crashes when pinned cache is generated with multiple VDs.(SCGCQ01936690) 
 - During drive spin up, drives come up as 0 bytes.(SCGCQ01944951) 
 - RMC: Add full interrupt disable to SBR Reload code.(SCGCQ01212765) 
 - SCSI format command send to NVMe drives fails with CMPLIST flag set in addition to FMTDATA flag.(SCGCQ01229799) 
 - SPI reset delay needs to be enabled in B0 revs.(SCGCQ01241767) 
 - Correct merge issues.(SCGCQ01437127) 
 - FW halts when attempting to set offline PD back to Online after Pinned Cache was generated.(SCGCQ01473162) 
 - pl: NVMe: rapid device removal/add with a specific vendor backplane.(SCGCQ01487423) 
 - Ensure COL descriptor alignment.(SCGCQ01487873) 
 - This looks like a merge issue. This code is a duplicate of the same lines above.(SCGCQ01497809) 
 - Check duplicate buffer init code.(SCGCQ01497815) 
 - Unaligned fields in raid.h.(SCGCQ01497871) 
 - calculate the correct memSize for EnclDcmdGetListExt to filter out the empty sgpio enclosure when there is an external enclosure.(SCGCQ01507541) 
 - pl: backend PCIe: workaround timer may trigger after too short of an interval(SCGCQ01518343) 
 - Controller crash when doing PD erase(SCGCQ01519099) 
 - MR 7.6 - HSP failed to kick in OPAL array(SCGCQ01523568) 
 - Move the BIOS reset under a workaround bit(SCGCQ01526980) 
 - OPAL: security password change does not work(SCGCQ01531842) 
 - Aero : Assertion failure in fw\cpu\arm\exceptions.c at line 938 after COL glitch test when boot to OS(SCGCQ01538897) 
 - To fix the phy to slot mapping issue for the UBM backplane(SCGCQ01542497) 
 - MR 7.6 - FW got stuck in loop while clearing OPAL foreign PDs(SCGCQ01553035) 
 - PL: Implemented HW workaround to solve 6G SATA link fail problem(SCGCQ01554661) 
 - Ventura: If firmware download is done in small pieces, firmware download fails with logInfo 30010402(SCGCQ01558208) 
 - MR 7.6 Assertion failure in ../../dm/src/dm.c at line 1540: 0" after pwr off the enclosure to generate pinned_cache(SCGCQ01561611) 
 - After flashing GPMR2 code 50.1.0-1048 on top of MR7.6 50.6.0-1029 code a critical error message seen(SCGCQ01562108) 
 - pl: backend PCIe: EC52 fault(SCGCQ01565749) 
 - 9460-16i Montask when running SMART polling on a Toshiba SSD drive(SCGCQ01568381) 
 - SED compatibility checks(SCGCQ01570655) 
 - Performance optimizations AI(SCGCQ01571030) 
 - compile error for IMR build(SCGCQ01572902) 
 - Change CCR preprocessor(SCGCQ01573815) 
 - Flow control can miss control characters(SCGCQ01573909) 
 - Ventura B0: Slot status LED updates to certain slots on NVMe backplane may fail(SCGCQ01574224) 
 - Transport Ready On/Off test sometimes fails after 12 hours.(SCGCQ01578489) 
 - MR7.6: iMR controller unresponsive after deleting foreign config(SCGCQ01586340) 
 - MR7.6 Drive Locate Not Working for all NVMe drives on OEM system(SCGCQ01586434) 
 -(SCGCQ01587330) 
 - Remove and Truncate command handler: IO was not failed with check condition(SCGCQ01594602) 
 - MR7.6 Vmware6.5 - Incorrect fatal error EVT after PassThrough enabled followed by Guest OS power on(SCGCQ01599329) 
 - Handling review comments rearranging the logic of SGL chain pull(SCGCQ01601099) 
 - Incorrect BAY Number assigned by the FW when the Invalid bit was set in SES_SAS_ADTNL_ELMT_STS_DSRPT_EIP1(SCGCQ01601131) 
 - Ventura BST 7.6 NVMe==> (Montask: Assertion failure in ../../hw/inc/3516_inc/memory.h at line 443(SCGCQ01602556) 
 - Aero-3: make aero doesn't compile(SCGCQ01614670) 
 - Correct build issues(SCGCQ01615843) 
 - Copyback drive becomes foreign after removing/insertting drives when DG is in TR state(SCGCQ01619840) 
 - AULBA divert bitmap not enabled on R5/R6 WT Vds(SCGCQ01619858) 
 -(SCGCQ01620250) 
 - internal megamon command hangs(SCGCQ01620952) 
 - Aero3: Signed CBB hangs(SCGCQ01624857) 
 - Use LdIsValid(SCGCQ01632088) 
 - Few TR PDs are not marked foreign after DG removal and insertion(SCGCQ01638673) 
 - After removing TR DHSP and rebooting the system inserting DHSP drive becomes foreign(SCGCQ01640026) 
 - Upon inserting TR SDHSP drive import fails(SCGCQ01641758) 
 - MR7.5 18B CIT : if connection to EKMS is lost while online, drives are not in proper state after reboot(SCGCQ01670320) 
 - FW stated number of disks exceeded the max supported count with 14 PD(SCGCQ01680522) 
 - Exessive GetConnectorIndex(phyNum(SCGCQ01681563) 
 - Drive goes unexpectedly unconfigured good after escrow process(SCGCQ01682240) 
 - Continue monitoring parts capable of functioning following a code download(SCGCQ01683212) 
 - Aero DDR: DDR fails after issuing MSS reset(SCGCQ01685637) 
 - An interrupted code download could force VDs to be in write-thru mode until the next successful code download.(SCGCQ01685900) 
 - Ventura: OEM ID66 PCIe Switch backplane Slots Status Amber LEDs stay blinking(SCGCQ01687610) 
 - MR7.7: Secured JBOD FDE drive migrate from iMR (secured(SCGCQ01687761) 
 - Core 1 Execution Locks(SCGCQ01698188) 
 - Unable to recover config when changing security password before re-inserting drives(SCGCQ01715058) 
 - Aero PA0.5: PL Fault 0xD075 during preboot OCR test(SCGCQ01715535) 
 - LD Allowed Op Secure bit was set for non-secured LD(SCGCQ01718177) 
 - RMC: Need to use AHB path to write to Reset Status Register(SCGCQ01718319) 
 - Event with invalid slot # during pd insertion when a command is timed out(SCGCQ01721492) 
 - update custom3516.h changes from SCGCQ01608027 to custom3916.h(SCGCQ01733052) 
 - Aero PA0.5:FW fails to boot to SafeMode. SafeMode behavior changed from previous FW.(SCGCQ01733068) 
 - Intermittent failures in CPU trace capture FSM initialization across OCR, host restart(SCGCQ01747998) 
 - [Ventura 7.7] Coverity Fixes(SCGCQ01753268) 
 - [iMR7.5][Bristol] Amber LED doesn't turn on with PD offline(SCGCQ01767172) 
 - PD SCSI passthru (READ/WRITE commands(SCGCQ01787981) 
 - Ventura: OEM PCIe dual switch attached backplane slot status LED stays Amber on partial slots(SCGCQ01788989) 
 - Added capability to blink LED for Hotspare drive(SCGCQ01789741) 
 - MCTP: 0x265D fault occurs when running high MCTP PCIe VDM load with MCTP Discovery commands(SCGCQ01790303) 
 - Update combo serdes library version(SCGCQ01791178) 
 - Data Store creation does not complete(SCGCQ01792710) 
 - The Wrap around condition for snap-dump does not take care of few scenarios. Also add the time stamp for each snapdump in F/W(SCGCQ01798249) 
 - Aero PA0.6: Max Resets per boot cycle reached after 2 OCR cycles and controller stuck(SCGCQ01800508) 
 - Aero PA0.6: Problem = Firmware lock up while booting. Attempt to force FW into SafeMode with pinned cache present.(SCGCQ01800574) 
 - Interrupts not handled in fault state if a high priority interrupt handler faults(SCGCQ01802508) 
 - SGPIO - backplane LED does not show amber when PD is offlined.(SCGCQ01809027) 
 - HDDs spin up failed during boot time and then cause ac cycle failed after around 70 power cycles(SCGCQ01813023) 
 - Fix unsecure/rollback security on LD(SCGCQ01816643) 
 - Error message "Disabling writes to flash due to a critical error" seen during FW upgrade/downgrade MR 7.7 to MR 7.1(SCGCQ01816659) 
 - FW assertion during boot(SCGCQ01818283) 
 - Legacy BIOS Prints "This firmware is a TEST version"(SCGCQ01825992) 
 - Issue: "Overflow -- Text Discarded" messages seen in termlog.(SCGCQ01830664) 
 - Ventura PL: 0x670A Fault During Destructive Domain Testing(SCGCQ01831332) 
 - Firmware hit exception monstak when trigger BBU retention test ( /cx/bbu start retentiontest(SCGCQ01832979) 
 - Amber Drive Enclosure LED Does Not Turn On to Indicate a Failed SAS or SATA Drive(SCGCQ01840037) 
 - Unwanted prints removed(SCGCQ01873256) 
 - Data Abort Exception observed while running reboot test with a bad drive.(SCGCQ01985789) 
 - Correct defines section(SCGCQ01390738) 
 - Aero: I/O drop on NVMe partition when trigger OCR overnight with rebuild in mix mode profile 13(SCGCQ01460586) 
 - Add zlib to the build(SCGCQ01461126) 
 - Rename after merge completes as per coding standards(SCGCQ01497806) 
 - consolidate ReconInProgress using IoPathFlagReconActiveGet/Update(SCGCQ01497831) 
 - Invalid SenseBufferLowAddress in iMR(SCGCQ01509909) 
 - Correct iMR linking(SCGCQ01510048) 
 - FW hit montask intermittently and fails to flash PD FW using storeCLI(SCGCQ01523586) 
 - MR-7.6: RAID0 Volumes go to in-consistent after importing with pinned Cache.(SCGCQ01524665) 
 - MR 7.6 - FW hangs during POST while rebooting in loop(SCGCQ01545245) 
 - Merge Errors(SCGCQ01556741) 
 - Dev: Remove LD_DEALLOCATION_SUPPORT macro for unmap feature(SCGCQ01558830) 
 - MR 7.6 - FW hit mon_task while running cablepull failover in JBOD environment(SCGCQ01566599) 
 - Merge board fixes(SCGCQ01571587) 
 - Ventura B0: Slot status updates to certain slot on NVMe backplane may not update the LED status(SCGCQ01573106) 
 - FW hits assertion failure in fw\mros\mem.c at line 629 : mb->tag==tag while using OOB storelibtest creates R50(SCGCQ01577504) 
 - Replace drive failed on secured array with OPAL drives(SCGCQ01582713) 
 - 7.6--9460-16 controller: JBOD mode created raid LD tgtId is reset to 0 after changing back to RAID mode.(SCGCQ01587151) 
 - on enabling/disabling the UNMAP feature, storcli doesn't print any message asking to reboot the server(SCGCQ01595432) 
 - Unmap/Write command gets executed on EPD's when controller is in JBOD mode.(SCGCQ01607475) 
 - DISM - Assertion failure in ../../dm/src/devRemoval.c for breaking multipath during bootup(SCGCQ01618628) 
 - Many prints "T35: C0:MPT_SASPhyPage: Failed chip x00 phyNumber x09 retVal x0022" seen(SCGCQ01620617) 
 - PA1-MR-7.7-FW: Assertion when forcing kdump with chaos IOs and RHEL 6.9 x64 on R0 VD(SCGCQ01620726) 
 - Code review cleanup(SCGCQ01635769) 
 - EnclSgpioHandleDevicePresenceCallback:should never happen logic/internal seen(SCGCQ01640052) 
 - Unmap related WJ should not be present when downgraded to non-unmap supported FW(SCGCQ01641105) 
 - Assertion failure in ../../raid/taskman.c at line 139: func != NULL(SCGCQ01641743) 
 - MR 7.7 : Storcli shows incorrect data for /c0 show linkconfig for Ventura controller.(SCGCQ01655579) 
 - Cache Offload capabilities determined by component attributes instead of part numbers(SCGCQ01670387) 
 - MR7.6: Firmware hit montask running task management reset in loops(SCGCQ01675742) 
 - StorCLI fails to set TR on all DGs with "dall" option-individual DG OK(SCGCQ01681695) 
 - UNMAP commands are returned with error status on NVME JBODs/EPDs, even when UNMAP is exposed as supported(SCGCQ01683113) 
 - MR7.7:Assertion failure in fw\mros\mem.c @ line 794:Mem header and footer contents are out of sync when poweroff cmd in linux(SCGCQ01686649) 
 - FW fails to detect TR SDHSP & DHSP upon insertion(SCGCQ01687759) 
 - LSA version 4.132 shows blank page or extreme sluggish to do anything(SCGCQ01698418) 
 - Unmap capability not displayed(SCGCQ01715253) 
 - HII & StorCLI Profile list shows Profile 0(SCGCQ01718982) 
 - incrementing other error count for RECOVERED_ERROR with any asc and asc apart from 00/1d(SCGCQ01729713) 
 - Firmware ASSERT(SCGCQ01729837) 
 - (SATA Only(SCGCQ01732835) 
 - Too many SnapDumpAllocBufferMemory: Called in firmware log when do diffrent operation in LSA(SCGCQ01746171) 
 - MR7.7 Alpha: Drive Locate Not Functional with 9440-8i(SCGCQ01747208) 
 - Firmware Doesn't Print Call Stack Information During Exception Handling(SCGCQ01747586) 
 - Fix compilation errors integrating PL 7.250.02(SCGCQ01749420) 
 - fix so that LSISAS3916.xsd can generate SBR data with sas2parser.exe -binary.(SCGCQ01749453) 
 - MR7.7: FW Auto Raid0 Creation Command is failing.(SCGCQ01749779) 
 - Aero PA0.5: storcli /cx/jbodx start erase standard is not working(SCGCQ01750220) 
 - Aero PA0.5: hole in VD id assignment sequence after one or more VDs are imported(SCGCQ01750230) 
 - Controller hits KA because cmdblock does not complete due to pending flush.(SCGCQ01753381) 
 - KA on iMR w MemPoolAlloc((SCGCQ01753407) 
 - Controller is not come up after it crash with Snapdump enable(SCGCQ01764241) 
 - DevBST failing on non-BMC capable setups in the last step(SCGCQ01764502) 
 - Random prints are seen in the firmware logs in BMC_Emulator setup.(SCGCQ01775670) 
 - Change vendorIdentification to LSI for Ventura(SCGCQ01776239) 
 - StorCLI - Aero PA-0.6: Snapdump properties default values different after disabling and re-enabling its feature(SCGCQ01789798) 
 - Generate correct snapdump number information(SCGCQ01790830) 
 - Aero PA0.6: if OCR starts by entering debugger and exiting out after 3:51, FW doesn't complete OCR(SCGCQ01791025) 
 - Data corruption seen on unmap capable R5/6 LD(SCGCQ01794084) 
 - Remove the unnecessary snapdump when import incomplete foreing configuration(SCGCQ01799264) 
 - RMC locks up attempting to access A15 PC register via CoreSight(SCGCQ01800745) 
 - Aero PA0.6: FW don't POST after upgrading to pkg: 50.8.0-1447 (SCGCQ01790806(SCGCQ01802524) 
 - if host I/O is blocked by VD cache flush and PD entered shielded state, it may hit kill adapter.(SCGCQ01811249) 
 - MR crash when processing some NVMe admin-queue pass-thru commands(SCGCQ01811258) 
 - long uart dump of information after Killadapter(SCGCQ01813618) 
 - Incomplete event message(SCGCQ01824948) 
 - MR fw doesn't report that SAS_SATA 6 G and 3G capability(SCGCQ01870194) 
 - Reverting the changes delivered.(SCGCQ01886389) 
 - bounds check not correctly performed on patrol read if media defect exists on the last block of PD(SCGCQ01942077) 
 - Driver detected a FW hang with Jbod create and Del with Ctrl property change(SCGCQ01970454) 
 - Fault C010 encountered when running IO to 9405W-16e in Target Mode(SCGCQ01368001) 
 - Event shown incorrectly if supercap missing(SCGCQ01425227) 
 - Aero : Continous error " MPT_PcieDevicePage: Failed chip 0 pageNumber: 0 pageAddress 15 retVal 22" when pull out NVMe drives(SCGCQ01455656) 
 - WG: CC is not aborted when there is a replace operation triggered on a R1 VD.(SCGCQ01466733) 
 - Win/Lin Ventura MR7.5 ROP 970 , -6% regression in RAID1, 4K, SR, QD4 ( 4 workers tests(SCGCQ01537079) 
 - Smart Return Status passthru command failed on SATA drives(SCGCQ01555033) 
 - Transport Ready On/Off test fails when run for more than 6 hours.(SCGCQ01570249) 
 - 7.6 Alpha: pk1114, exception line 938 while format JBOD in Raid mode for NVMes OEM Workstation(SCGCQ01594649) 
 - FW can lose AltSel and DrvStrength(SCGCQ01635796) 
 - Purely Server: Firmware Not Logging to Flash or Can't be Uploaded with StorCLI(SCGCQ01639777) 
 - Firmware hangs during boot(SCGCQ01665148) 
 - MR PD GET info fails for SES processor(SCGCQ01685797) 
 - copy back on wrong PD type(SCGCQ01718152) 
 - MR7.6: Assertion failure in ../../mros/mem.c at line 806: mb->tag==tag after issue a reboot cmd (server reboot(SCGCQ01721366) 
 - Issue: cannot create datastore for raid 0 with unmap VD.(SCGCQ01753372) 
 - Firmware exception during rebuild on SAS and SATA R1 VDs that has 500 medium errors(SCGCQ01816682) 
 - Fault 4311 when running repeated controller resets(SCGCQ01865882) 
 - PL Spinup: Firmware Takes a Long Time to Grant Spinup to Some Drives/Phys(SCGCQ01963394) 
 - Phy Connections count not sent properly to application(SCGCQ01970476) 
 - Aero : ERROR: Exception Handler Called for Processor Core = 0 when migrate from R5 to R5(SCGCQ01489072) 
 - Multitarget builds fail(SCGCQ01556899) 
 - StorCLI return Status = Failure run storclif64.exe /c0 show largeIOsupport(SCGCQ01564798) 
 - instant erase fails(SCGCQ01566600) 
 - Disk Group drives become unconfig good upon insertion when DHSP has remained in the system(SCGCQ01588846) 
 - Update BST scripts for JBOD personality auto BST(SCGCQ01685004) 
 - MR7.7: OPAL R0 PD goes missing/failed if pulled & reinserted < 3 secs.(SCGCQ01697879) 
 - After deleting Drive Group, dedicated hot spare assigned to the drive group did not become unconfig good(no other drive group present(SCGCQ01813795) 
	and remained as global hot spare
 - Merge issue resulting in compilation error(SCGCQ01851569) 
 - Resolve merge conflicts(SCGCQ01533348) 
 - Disable OPAL SED feature on 7.6(SCGCQ01571711) 
 - iMR: virtual memory mappings with different cache properties in violation of ARM rules(SCGCQ01606621) 
 - LAS does not show proper state of secured locked drives.(SCGCQ01615781) 
 - An error message "03/22/18:EnclSgpioLocatePd[1198]: Invalid Slot Number [255] For Pd[134]" after clearing config from LSA(SCGCQ01665275) 
 - Return appropriate error codes in function cfgDcmdAddCheckParams - Unable to import CIO VD(SCGCQ01737595) 
 - Change __SERIES_3916__ to SERIES_3916(SCGCQ01776572) 
 - Duplicated SnapDump ID Seen when the series of dumps are created and retrieved.(SCGCQ01789861) 
 - OPAL Error recovery(SCGCQ01559776) 
 - [UNMAP] 7.6 PA2 : UNMAP doesn't get disabled when a drive which doesn't support UNMAP becomes part of the VD(SCGCQ01572067) 
 - Correct IoPathFlagReconActiveGet(SCGCQ01632090) 
 - MR7.7: iMR FW hit assertion montsk((SCGCQ01641570) 
 - Aero PA0.5: FW fails to create VD in Profile 12 when you have 208 VD's and you delete 16 VD's and try to create 16 more VD's(SCGCQ01761452) 
 - Firmware Boot Fault when Performing Online Firmware Upgrade(SCGCQ01786671) 
 - ChianMid issue handling for NVMe based volumes(SCGCQ01922016) 
 - DG and its SDHSP drives become unconfigure bad upon removal & insertion(SCGCQ01570451) 
 - Patrol read progress pause when user try to change profile(SCGCQ01614870) 
 - Drives are reverted back to JBOD after perfoming instant secure erase(SCGCQ01615777) 
 - FW DDR Initialization Doesn't Correctly Account for Bus Width(SCGCQ01697679) 
 - Same EID assigned to 2 530-8i controllers(SCGCQ01883096) 
 - Remove CSET SCGCQ01961503(SCGCQ01991115 port of SCGCQ01990091) 
 - PL : Task management timeout is observed if the task management type is invalid(SCGCQ01980452 port of SCGCQ01969521) 
 - Ventura: Use full Slot Cap Physical Slot Number field info for PCIe SW attached device slot enumeration(SCGCQ01969772 port of SCGCQ01936123) 
 - (vSES) Injecting error on I2C channel of one connector module will cause LED of another connector module to not work.(SCGCQ01961504 port of SCGCQ01955094) 
 - Heavy IO with low IO timeout test may result into an IO getting missed.(SCGCQ01867066 port of SCGCQ01631346) 
 - To support the SEP reset functionality through CPERST in order to avoid warm boot CPLD issues(SCGCQ01851006 port of SCGCQ01851006) 
 - [Ventura][PL] TM Hangs when doing drive push pull test case(SCGCQ01817008 port of SCGCQ01792208) 
 - pl: backend PCIe: port enable may complete before PCIe mode is attempted(SCGCQ01794153 port of SCGCQ01760627) 
 - IOC_CTRL_OP_ALL_PHY_LOOPBACK operation is not working(SCGCQ01792619 port of SCGCQ01670396) 
 - IO not completing or being timed out if some cases when an unconfirmed response is received for an IO.(SCGCQ01767091 port of SCGCQ01718897) 
 - Host memory corruption seen during Progress polling of Sanitize operation on SATA drives(SCGCQ01762343 port of SCGCQ01721050) 
 - MCTP PCIe VDM: controller stops responding after sending over 1000 asynchronous events(SCGCQ01760767 port of SCGCQ01742362) 
 - (SATA Only(SCGCQ01745744 port of SCGCQ01732835) 
 - Unhandled exception results in a fault(SCGCQ01721368 port of SCGCQ01686666) 
 - (SATA only(SCGCQ01720496 port of SCGCQ01681441) 
 - (SATA only(SCGCQ01714249 port of SCGCQ01681441) 
 - Not all NVMe drives discovered as part of hot plug operation(SCGCQ01713380 port of SCGCQ01697329) 
 - VPD is not shown by lspci(SCGCQ01698316 port of SCGCQ01687750) 
 - Mercator Phase7: VMWare PSODs due to NMI error when the Windows VM that has passthrough controller is being shutdown(SCGCQ01697675 port of SCGCQ01617769) 
 - Ventura B0: Fault 0x4311 while running HBA phys off/on & drive hard reset(SCGCQ01687743 port of SCGCQ01619417) 
 - IO unit control IOC_CTRL_OP_ALL_PHY_LOOPBACK_DIAG hangs on 8 phy controller(SCGCQ01687624 port of SCGCQ01623477) 
 - pl: NVMe: E411 fault(SCGCQ01686689 port of SCGCQ01684788) 
 - Not all NVMe drives were discovered after server cold or warm boot(SCGCQ01686240 port of SCGCQ01664963) 
 - Not to do all drives reset at the start of the boot up on each port of the controller(SCGCQ01682349 port of SCGCQ01670965) 
 - Ventura: Disable drive presence based PCIe RefClk and PERST control for OEM ID66 backplane(SCGCQ01676883 port of SCGCQ01670180) 
 - MCTP: Fault 0x265d while doing enclosure pull/push with OOB StoreLibIT when enabling AEN(SCGCQ01675747 port of SCGCQ01631826) 
 - PL: Change to Customer Specific SMP Response Report Manufacturer(SCGCQ01641073 port of SCGCQ01505468) 
 - Align vSES diag page response with Expander SEP diag page response(SCGCQ01639886 port of SCGCQ01585387) 
 - SES Page 2 Overall Status-Status Info bits do not reflect the correct status after fault conditions are cleared(SCGCQ01639873 port of SCGCQ01620243) 
 - Blank Boards with Auto Port Enable set in NVDATA will fault(SCGCQ01639859 port of SCGCQ01553238) 
 - SES Page 2 does not show the correct status information for Direct Attached NVMe drives(SCGCQ01639840 port of SCGCQ01620857) 
 - Negotiated Link Speed for the vSES target is displayed as 'Unknown'.(SCGCQ01639536 port of SCGCQ01606720) 
 - Ventura B0: 5813 fault while running destructive domain test(SCGCQ01630895 port of SCGCQ01623624) 
 - Ventura: No easy way to tell if config pages have been written(SCGCQ01630398 port of SCGCQ01630331) 
 - (SATA Only(SCGCQ01630267 port of SCGCQ01628346) 
 - The PCIe reset to be handled properly for the Change detect feature(SCGCQ01628453 port of SCGCQ01623437) 
 - The PCIe reset to be handled properly for the Change detect feature(SCGCQ01628451 port of SCGCQ01623437) 
 - The change detect feature macro missing, leading to compilation issue(SCGCQ01628450 port of SCGCQ01616460) 
 - To implement the CHANGE_DETECT GPIO feature for the UBM backplanes(SCGCQ01628439 port of SCGCQ01507506) 
 - When spinup delay in expander is configured to a high value it might result in some drives being reset by controller repeatedly.(SCGCQ01628174 port of SCGCQ01601413) 
 - IO starvation and performance degradation when using dma Q masking feature(SCGCQ01627326 port of SCGCQ01505074) 
 - Not all NVMe drives are discovered on VPP backplane Enclosure(SCGCQ01623525 port of SCGCQ01620856) 
 - pl: NVMe: 61A6 fault(SCGCQ01619934 port of SCGCQ01602703) 
 - PL Enclosure Management: SEP Blink Request Fails After Path 1 Disconnect in Multipath Topology(SCGCQ01619021 port of SCGCQ01618625) 
 - pl: backend PCIe: EC59 fault(SCGCQ01618750 port of SCGCQ01615981) 
 - Task Management due to SATA init failure results in resource error message(SCGCQ01618661 port of SCGCQ01605610) 
 - (SATA Only) ATA Request Sense Ext command being sent after ATA command translated for SCSI Start Stop Unit command fails with Sense Data Available.(SCGCQ01618209 port of SCGCQ01599542)
 - (SATA Only) Timer for SCSI Write Verify command to a SATA drive might get removed before command completion.(SCGCQ01616558 port of SCGCQ01593136) 
 - Increase the default SES buffer size to 2K(SCGCQ01616503 port of SCGCQ01506013) 
 - (SATA Only) Incorrect data sent in response of SCSI Inquiry command for some SATA drives.(SCGCQ01616465 port of SCGCQ01599707) 
 - (SATA Only) ATA Request Sense Ext command not sent for failed SCSI Unmap command sent to a SATA drive(SCGCQ01615209 port of SCGCQ01593844) 
 - (SATA Only) ATA Request Sense Ext command sometimes not send when the drive responds with 'Sense Data Available' bit set.(SCGCQ01615159 port of (SCGCQ01571933) 
 - (SATA Only) SCSI Unmap command to some SATA drives are timing out.(SCGCQ01615122 port of SCGCQ01539572) 
 - pl: NVMe: D102 fault(SCGCQ01608155 port of SCGCQ01605590) 
 - DDRlib failures occur if debug prints are disabled.(SCGCQ01599770 port of SCGCQ01482222) 
 - Ventura B0: Slot status LED updates to certain slots on NVMe backplane may fail(SCGCQ01598554 port of SCGCQ01574224) 
 - pl:NVMe: Write Long (10) fails when LBA exceeds 0x7FFFFFFF(SCGCQ01595859 port of SCGCQ01593652) 
 - pl: NVMe: device may not appear in OS following NVMe init failure(SCGCQ01594709 port of SCGCQ01593528) 
 - To fix the LED issue, VPP data and moving to change detect poll state(SCGCQ01582246 port of SCGCQ01576165) 
 - To fix issues for back plane configuration validation and LED control for the UBM backplane.(SCGCQ01582240 port of SCGCQ01533852) 
 - Fixing the issues during bringup of the universal backplane.(SCGCQ01581911 port of SCGCQ01522148) 
 - pl: backend PCIe: 4311 fault (part 3(SCGCQ01574924 port of SCGCQ01537791) 
 - Collect enclosure Bay ID from OEM specificinternal backplanes(SCGCQ01562101 port of SCGCQ01503517) 
 - Performance Improvements(SCGCQ01562098 port of SCGCQ01455538) 
 - pl: backend PCIe: switch attached discovery takes too long(SCGCQ01556426 port of SCGCQ01522343) 
 - PL: Revised "Avoid Duplicate Mid" Feature Code Could Incorrectly Allow IO to Start Through PL Firmware Path(SCGCQ01556419 port of SCGCQ01520524) 
 - Increase the default SES buffer size to 2K(SCGCQ01540666 port of SCGCQ01506013) 
 - PL Fault 0000ecdd LR 01403837 during initial discovery(SCGCQ01539840 port of SCGCQ01531770) 
 - PL: Change to Customer Specific SMP Response Report Manufacturer(SCGCQ01533308 port of SCGCQ01505468) 
 - PL: Fault 0x5862 seen when host buffer size is smaller than allocation length in CDB(SCGCQ01529512 port of SCGCQ01509770) 
 - pl: backend PCIe: non-NVMe endpoint not cleaned up on removal(SCGCQ01529383 port of SCGCQ01516968) 
 - Get VDM Support command does not have VendorID and VendorAddInfo fields properly populated(SCGCQ01525228 port of SCGCQ01450475) 
 - pl: backend PCIe: 4311 fault with NVMe enabled (part 2(SCGCQ01523550 port of SCGCQ01523531) 
 - pl: NVMe: rapid device removal/add with a specific vendor backplane(SCGCQ01522511 port of SCGCQ01487423) 
 - pl: backend PCIe: workaround timer may trigger after too short of an interval(SCGCQ01519802 port of SCGCQ01518343) 
 - Need to expose pure SEP devices through the inventory command(SCGCQ01519056 port of SCGCQ00943216) 
 - STANDBY_Z Bit Not Set in POWER CONDITION MODE PAGE When Mode Sense (10(SCGCQ01518957 port of SCGCQ00845242) 
 - (SATA Only) Signature FIS not validated for Expander attached SATA drives(SCGCQ01514869 port of SCGCQ00852290) 
 - IOP: Faulting for L2 Cache Correctable Errors(SCGCQ01514707 port of SCGCQ01264714) 
 - Fault State (0x265d(SCGCQ01514262 port of SCGCQ00856085) 
 - Fault State (0x265d(SCGCQ01513298 port of SCGCQ00856085) 
 - PL: SAS3 PHASE12 RAID creation failing with SATA drives.(SCGCQ01512834 port of SCGCQ00998155) 
 - IOP: Faulting for correctable L2 parity errors(SCGCQ01512800 port of SCGCQ00934325) 
 - IOP: Differentiate between L2 correctable and uncorrectable faults(SCGCQ01512630 port of SCGCQ00929810) 
 - SATA ONLY: VPD page 0xB2 LBPU bit not set correctly.(SCGCQ01511589 port of SCGCQ01374552) 
 -(SCGCQ01431063 port of SCGCQ01415060) 
 - 9305-16i - Activity LED signal is not asserted for port 2 and 3.(SCGCQ01382008 port of SCGCQ01318981) 
 - PL: Error LED stays on when drive is pulled out when using unusual slot mapping and drive presence check(SCGCQ01222315 port of SCGCQ01157331) 
 - Parameter Page Invalid, Setting channel count based on DDR Size.(SCGCQ01442953 port of SCGCQ01440768) 
 - MR7.4 Beta: Direct Attached SAS HDDs go Unconfigured Bad at Power-On (ROP 834 & earlier is OK(SCGCQ01491155 port of SCGCQ01487263) 
 - rename the function .(SCGCQ01540240 port of SCGCQ01523374) 
 - 2nd attempt to set SubOem via OOB fails(SCGCQ01561807 port of SCGCQ01542531) 
 - MR7.3.1_Assertion failure in ../../dma/dmaxor.c at line 1180:(SCGCQ01574070 port of SCGCQ01482384) 
 - Set ldRestriction appropriately in MFCD parameters and persistent config pages(SCGCQ01578302 port of SCGCQ01487406) 
 - Incorrect Micron NAND Model Number read from flash(SCGCQ01579248 port of SCGCQ01531136) 
 - STP Passthru commands end up with blank FiS response buffer(SCGCQ01582504 port of SCGCQ01576179) 
 - Drive Fault LED lighting but drive seems good(SCGCQ01582515 port of SCGCQ01567500) 
 - CC doesn't start on special built OEM firmware(SCGCQ01582533 port of SCGCQ01559661) 
 - 9460-8i is reporting Chip Temperature of 255 when the ambient temp is about 0 C(SCGCQ01582535 port of SCGCQ01565568) 
 - 9460-8i is reporting Chip Temperature of 255 when the ambient temp is about 0 C(SCGCQ01582536 port of SCGCQ01565568) 
 - Linux driver incorrect issuing MR_DCMD_DEV_GET_TARGET_PROP to enclosure devices(SCGCQ01603016 port of SCGCQ01403758) 
 - Use redundant copies of NVRAM for COL(SCGCQ01605531 port of SCGCQ01516947) 
 - Adding the code to clear the device restriction in case of firmware download failure return from the device(SCGCQ01605591 port of SCGCQ01392785) 
 - Rebuild reported as in progress instead of a paused state when not at OS.(SCGCQ01605608 port of SCGCQ01301433) 
 - Enhance Messaging Unit error ISR to dump debug information of virtual functions having error(SCGCQ01605632 port of SCGCQ01553249) 
 - MR FW: Select SAS1/PDB1 BISR group by setting BisrSmsG = 0x0C in BISR Control register during Initial Power Up.(SCGCQ01614614 port of SCGCQ01614205) 
 - Enclosures is not exposed to Host even if exposeEnclosureToHost is set.(SCGCQ01615762 port of SCGCQ01599832) 
 - Smart Return Status passthru command failed on SATA drives(SCGCQ01617112 port of SCGCQ01555033) 
 - [OOB]RMC/MR Crash Due to PCE Core Register Access Errata during vSAN certification Test(SCGCQ01617139 port of SCGCQ01521255) 
 - JBOD pred fail drive amber LED behavior not as expected(SCGCQ01622027 port of SCGCQ01583521) 
 - The Auto Config feature not present in HII(SCGCQ01627671 port of SCGCQ01406286) 
 - Patrol read progress pause when user try to change profile(SCGCQ01628441 port of SCGCQ01614870) 
 - Coding standard defect found during Dev Review(SCGCQ01629342 port of SCGCQ01628784) 
 - Virtual drive shows failed after creating 240 VDs(SCGCQ01631156 port of SCGCQ01624871) 
 - Issue: JBOD devices were dropped after unloading driver and reloading driver in linux(SCGCQ01633028 port of SCGCQ01566087) 
 - Increase the recon BB list entries to align with BBM MAX BAD entries(SCGCQ01633667 port of SCGCQ01623254) 
 - MR/iMR fill the tty log with congested I2C 4 Timeout events(SCGCQ01634722 port of SCGCQ01575197) 
 - Assertion failure in ../../cpu/arm/exceptions.c at line 938 observed while running push/pull of JBOD with IO(SCGCQ01639246 port of SCGCQ01616664) 
 - : FW asserts when invalid parameters to set excluded ld for CC is sent to firmware.(SCGCQ01639939 port of SCGCQ01635729) 
 - Event Log Corruption.(SCGCQ01641725 port of SCGCQ01451417) 
 - [MR7.5] Rebuild Progress 0 % logged just after OS reboot during rebuild running(SCGCQ01670392 port of SCGCQ01631496 ) 
 - After FW update, controller was not reset by the OCR command, and if user retries the command, then FW hits the exception(SCGCQ01681867 port of SCGCQ01639394) 
 - LAS does not show proper state of secured locked drives.(SCGCQ01683098 port of SCGCQ01615781) 
 - OCR is disabled by default for 9460-8i 2Gb(Talladega(SCGCQ01683353 port of SCGCQ01640678) 
 - LD Create blocks during crypto erase.(SCGCQ01685873 port of SCGCQ01639908) 
 - Parallel FW update on Configured drives w/o using force returns success message(SCGCQ01687074 port of SCGCQ01676420) 
 - HII allows setting controller personality through Manage Controller Profile menu(SCGCQ01714802 port of SCGCQ01685583) 
 - HII - HII reports "Invalid Value" popup when attempting to view a PD after switching to eHBA mode (before rebooting(SCGCQ01714804 port of SCGCQ01685785) 
 - After pulling some VDs, and rebooting, the remaining VD shows as foreign in RAID mode.(SCGCQ01714810 port of SCGCQ01698268) 
 - Not able to set max no of PD using set patrol read properties in LSA/Storcli(SCGCQ01722279 port of SCGCQ01671189) 
 - [iMR7.5] Memory allocation failure during RAID operation cycles under high loading(SCGCQ01727272 port of SCGCQ01697700) 
 - Purely Server: Firmware Not Logging to Flash or Can't be Uploaded with StorCLI(SCGCQ01732049 port of SCGCQ01639777) 
 - Logical Block Provisioning VPD Page (0xB2(SCGCQ01732074 port of SCGCQ01715293) 
 - Unable to abort a personality change and switch back to current personality without rebooting(SCGCQ01742563 port of SCGCQ01731927) 
 - FW reports incorrect error when attempting to import a VD when max VDs are configured.(SCGCQ01742565 port of SCGCQ01731942) 
 - Add new field to MrParamsPage1 in 3508.xsd and 3516.xsd(SCGCQ01742569 port of SCGCQ01742549) 
 - MR7.5 18B CIT : if connection to EKMS is lost while online, drives are not in proper state after reboot(SCGCQ01742585 port of SCGCQ01670320) 
 - 9460-16i UEFI HII doesn't show SMART Error while inserting a SMART failing drive. However 9361 works fine(SCGCQ01746340 port of SCGCQ01713714) 
 - Patrol read restarts on PDs after completion on reboot(SCGCQ01746342 port of SCGCQ01718200) 
 - Controller timestamp incorrect after performing an OCR.(SCGCQ01750291 port of SCGCQ01732066) 
 - Pinned cache is not flushed after importing drive in VD with pinned cache(SCGCQ01750308 port of SCGCQ01620531) 
 - Inconsistent CC progress % is logged after reboot during CC(SCGCQ01753387 port of SCGCQ01683057) 
 - Cannot stop patrol read on PD with medium errors by the stop cmd(SCGCQ01753389 port of SCGCQ01715992) 
 - Assertion failure in ../../cpu/arm/exceptions.c at line 938 observed, while deleting VD's with BG IO's(SCGCQ01753393 port of SCGCQ01713234) 
 - Importing a foreign secured drive with a different security key does not auto configure as an EPD after being unlocked.(SCGCQ01763494 port of SCGCQ01739088) 
 - No way to view the new API supportForcePersonalityChange bit.(SCGCQ01776329 port of SCGCQ01764237) 
 - FW setting support force bit with 1. Expectation is this should be set to 0 for external controller.(SCGCQ01776331 port of SCGCQ01764348) 
 - CLI does not block ERASE for ePD (non-RAID/JBOD(SCGCQ01776338 port of SCGCQ01765887) 
 - Reduce bootup time by 15-20 seconds(SCGCQ01785008 port of SCGCQ01735563) 
 - Unmap R5/6: Implementation supporting new API and logic(SCGCQ01789235 port of SCGCQ01760871) 
 - Smart Return Status passthru command failed on SATA drives(SCGCQ01802574 port of SCGCQ01555033) 
 - MR FW return only compatible profiles(SCGCQ01809003 port of SCGCQ01789037) 
 - Controller will assert during system boot with Pinned Cache and Foreign drives present.(SCGCQ01809087 port of SCGCQ01729754) 
 - FW is not blocking switching to an unsupported profile(SCGCQ01809222 port of SCGCQ01698176) 
 - Aero PA0.6: FW don't POST after upgrading to pkg: 50.8.0-1447 (SCGCQ01790806(SCGCQ01811270 port of SCGCQ01802524) 
 - Block appropriate commands for JBOD drives.(SCGCQ01813887 port of SCGCQ01640051) 
 - After the pd pull push of one drive locate is getting stopped on other PD(SCGCQ01816664 port of SCGCQ01792324) 
 - Cachevault flash size is showing as 0KB for the controller(SCGCQ01816665 port of SCGCQ01792360) 
 - OOB SCSI passthru command (READ DEFECT 12(SCGCQ01817903 port of SCGCQ01793262) 
 - Dev-Defect: Moved the implementation and prototype of the function LdSetSecurity((SCGCQ01818291 port of SCGCQ01807427) 
 - FW assertion during boot(SCGCQ01824209 port of SCGCQ01818283) 
 - if host I/O is blocked by VD cache flush and PD entered shielded state, it may hit kill adapter.(SCGCQ01826257 port of SCGCQ01811249) 
 - MR FW may return successful completion on host Rd cmd to EPD when the device is removed.(SCGCQ01826259 port of SCGCQ01804389) 
 - FW returns success for enabling encryption when it is failed on the drives(SCGCQ01841150 port of SCGCQ01830718) 
 - Erase operation is not happening on Multiple VDs(SCGCQ01842475 port of SCGCQ01835727) 
 - Controller hits KA because cmdblock does not complete due to pending flush.(SCGCQ01845204 port of SCGCQ01807618) 
 - dirty led not set on in case of supercap not present even though dirty cache is present(SCGCQ01866204 port of SCGCQ01825031) 
 - Firmware exception during rebuild on SAS and SATA R1 VDs that has 500 medium errors(SCGCQ01878349 port of SCGCQ01816682) 
 - erroneous configurable PD count decrement(SCGCQ01882408 port of SCGCQ01864432) 
 - MR_7.8: Fail to perform OCR , after FW upgrade from MR 7.7 to 7.8(SCGCQ01899545 port of SCGCQ01823917) 
 - Exposing Write cache as disabled to host for a performance improvement(SCGCQ01900925 port of SCGCQ01845298) 
 - Firmware ASSERT(SCGCQ01917788 port of SCGCQ01729837) 
 - Check the usage of SGE address in DmProcessBufferWaitQueue(SCGCQ01918166 port of SCGCQ01866804) 
 - Incorrect clearing of GUID to target ID map table during EPD creation(SCGCQ01920137 port of SCGCQ01909341) 
 - Observed Fatal Firmware Error on Talledega card during SLES 12 O/S installation.(SCGCQ01927603 port of SCGCQ01909779) 
 - Disable debug queue support(SCGCQ01930418 port of SCGCQ01880124) 
 - copyback fail to start on some PDs(SCGCQ01934952 port of SCGCQ01839637) 
 - CSCvm76418 - Locate LED for UG and JBOD drives connected to Talledega is not off after hot plug.(SCGCQ01942462 port of SCGCQ01927362) 
 - Firmware fault when continuously creating and deleting VDs/EPDs using attached batch script(SCGCQ01962221 port of SCGCQ01864769) 
 - SMP pass through not working when the “PD 0” is BAD drive(SCGCQ01978865 port of SCGCQ01945602) 
 - Source code uses tlbInitHDCW and HDCW instead of HCDW(SCGCQ01118580 port of SCGCQ01089693) 
 - vSES: CRIT or NON CRIT bits in Enclosure Status Diagnostic page are never set.(SCGCQ01967410 port of SCGCQ01942781) 
 - SATA: IO Timeouts with Read/Write and Non-Automated IO(SCGCQ01966771 port of SCGCQ01958700) 
 - (NVME) Fw Fault (faultcode 0xEC56) hit while performing system reboot test with NVMe drives attached.(SCGCQ01944366 port of SCGCQ01932728) 
 - Ventura: In mixed topology, attn LED is non-functional for SAS/SATA drives on OEM backplane(SCGCQ01941124 port of SCGCQ01930666) 
 - Incorrect vSES Data for Page 0x02 After Storcli Start & Stop Locate Operations for certain NVME Backplanes.(SCGCQ01897348 port of SCGCQ01671177) 
 - (SATA Only) SCSI Start Stop Unit command with power condition set to standby may fail for SATA drives.(SCGCQ01867137 port of SCGCQ01833392) 
 - [ventura] PL Fault 0000ecc9 observed, while running doing drive Pull-Push with IO's in background(SCGCQ01817257 port of SCGCQ01804290) 
 - Data NAK of large master TX packet can stop I2C out of band(SCGCQ01766431 port of SCGCQ01713685) 
 - PL support for monitoring the progress of sanitize operation.(SCGCQ01753174 port of SCGCQ01591935) 
 - PL: Avoid Duplicate Mid Workaround Does Not Start a TM If Device is Removed and Re-Added(SCGCQ01748033 port of SCGCQ01715677) 
 - The x4 link configuration was not detected by UBM module(SCGCQ01735502 port of SCGCQ01735485) 
 - Not all NVMe drives discovered as part of hot plug operation(SCGCQ01732136 port of SCGCQ01697329) 
 - Not all NVMe drives were discovered after server cold or warm boot(SCGCQ01732107 port of SCGCQ01664963) 
 - PL: Port Glitch on Direct Attached SATA drives,lead IO stop/File system become read only(SCGCQ01646094 port of SCGCQ01572062) 
 - (SATA Only) SCSI Log Select command not failed with check condition when translated ATA command is failed by SATA drive.(SCGCQ01633320 port of SCGCQ01631836) 
 - The change detect feature macro missing, leading to compilation issue(SCGCQ01628445 port of SCGCQ01616460) 
 - Change detect feature support on UBM supported back plane(SCGCQ01628444 port of SCGCQ01605371) 
 - Device block and unblock messages observed for the existing connected NVMe drives when new NVMe drive is inserted(SCGCQ01628423 port of SCGCQ01615532) 
 - pl: NVMe: ECEC fault(SCGCQ01623903 port of SCGCQ01620613) 
 - Ventura: Duplicate slot numbers assigned for drives in certain mixed mode cabling configurations(SCGCQ01623485 port of SCGCQ01606122) 
 - pl: NVMe: hot-added device may not appear in OS during heavy IO load(SCGCQ01619018 port of SCGCQ01616267) 
 - Ventura: FW Signing Support failing with loginfo during FWDL(SCGCQ01618988 port of SCGCQ01605427) 
 - (SATA Only(SCGCQ01618558 port of SCGCQ01605100) 
 - Requested capacity field translations are incorrect for remove element & truncate command(SCGCQ01614097 port of SCGCQ01510418) 
 - Ventura B0 Phase 7 - Fault E404 during IOTM testing with 24 NVMe drives and 3 switches(SCGCQ01600602 port of SCGCQ01570622) 
 - pl: backend PCIe: generic message header dWords 2 and 3 are swapped(SCGCQ01599051 port of SCGCQ01598812) 
 - (SATA Only(SCGCQ01593192 port of SCGCQ01539572) 
 - pl: NVMe: modify Bus Master Enable usage during NVMe controller reset(SCGCQ01587095 port of SCGCQ01581273) 
 - To fix the phy to slot mapping issue for the UBM backplane(SCGCQ01582244 port of SCGCQ01542497) 
 - Performance Improvements(SCGCQ01562099 port of SCGCQ01455538) 
 - pl: backend PCIe: link workaround not sufficiently coordinated with SAS link establishment(SCGCQ01556893 port of SCGCQ01540226) 
 - covery defects on Intruder 19849 & 19842(SCGCQ01542431 port of SCGCQ01484250) 
 - Storlib observed ERROR_MCTP_PAYLOADID_PE_INVALID_PARAM while doing attn-btn test(SCGCQ01542429 port of SCGCQ01423338) 
 - pl: NVMe: EC0D fault(SCGCQ01533267 port of SCGCQ01530402) 
 - Controller is not detecting in the storelib, after changing the mode from "set mode oob" command(SCGCQ01530310 port of SCGCQ01494018) 
 - (SATA Only) LBPRZ bit in VPD page 0xB2 is never set for SATA devices(SCGCQ01524353 port of SCGCQ01516277) 
 - Ventura hardware does not like the IOP enable method used here.(SCGCQ01519729 port of SCGCQ01514880) 
 - Coverity defects : The function seem called twice and identical code in different branches.(SCGCQ01516906 port of SCGCQ00939071) 
 - PL: SSD drop by SAS3008 during the hotplug test.(SCGCQ01516685 port of SCGCQ00897639) 
 - MR: Loading SBR with OFU causes system hang(SCGCQ01484420 port of SCGCQ01479700) 
 - SED Drive become UBad during secure erase on MegaRAID 9361-8i controller(SCGCQ01500319 port of SCGCQ01473188) 
 - 2nd arg passed in is not what the function is expecting, fix it(SCGCQ01537762 port of SCGCQ01497819) 
 - MR FW is not erasing ONFI and preparing ONFI for next offload right after flushing WJ entries(SCGCQ01570641 port of SCGCQ01564788) 
 - OCR hangs with IOs running(SCGCQ01570645 port of SCGCQ01564793) 
 - IO pauses for ~40 seconds when connecting/removing Multi-path cable(SCGCQ01570650 port of SCGCQ01505186) 
 - FW crashes while browsing configuration page MR Controller with Foreign configuration(SCGCQ01572305 port of SCGCQ01508045) 
 - Event with enclose 0x00 slot 0 during the system boot when a command is timed out (Command timeout on PD 12(e0x00/s0(SCGCQ01582499 port of SCGCQ01520443) 
 - SATA PassTrough commands with check condition taking long time to complete.(SCGCQ01582511 port of SCGCQ01561887) 
 - FW hits assertion failure in fw\mros\mem.c at line 629 : mb->tag==tag while using OOB storelibtest creates R50(SCGCQ01592822 port of SCGCQ01577504) 
 - Add logging messages in addition to previous fixes of a related issue, as requested by the Customer.(SCGCQ01602618 port of SCGCQ01584278) 
 - Ensure COL descriptor alignment(SCGCQ01616991 port of SCGCQ01487873) 
 - FW halts when attempting to set offline PD back to Online after Pinned Cache was generated(SCGCQ01616996 port of SCGCQ01473162) 
 - Correct minimum voltage calculation of Supercap(SCGCQ01619844 port of SCGCQ01558901) 
 - Colusa SAS expander reset results in unpredictable performance(SCGCQ01622026 port of SCGCQ01455811) 
 - Deletion of multiple VDs may fail via sideband in a MAXCONFIG setup (192 VDs(SCGCQ01631153 port of SCGCQ01590467 ) 
 - Inspect power loss for gaps(SCGCQ01641094 port of SCGCQ01569241) 
 - Sanitize progress in TTY log showing incorrect elapsed time(SCGCQ01681593 port of SCGCQ01630577) 
 - Assertion failure in ../../raid/taskman.c at line 139: func != NULL(SCGCQ01681821 port of SCGCQ01641743) 
 - NVDATA for iMR has maxChainedEnclosures set to 10; should be set to 2(SCGCQ01683362 port of SCGCQ01598760) 
 - Cache Offload capabilities determined by component attributes instead of part numbers(SCGCQ01684661 port of SCGCQ01670387) 
 - Sense code errors on PD's after FW is updated on them(SCGCQ01687073 port of SCGCQ01620609) 
 - MR 7.7 : Storcli shows incorrect data for /c0 show linkconfig for Ventura controller.(SCGCQ01697547 port of SCGCQ01655579) 
 - FW is not blocking switching to an unsupported profile(SCGCQ01714808 port of SCGCQ01698176) 
 - Drive offline FW download with mode E(offline method(SCGCQ01732072 port of SCGCQ01687616) 
 - Discrepancies between eHBA and RAID mode for cli show all output fields.(SCGCQ01750310 port of SCGCQ01729848) 
 - Disable Controller Security is not blocked after importing secure EPDs.(SCGCQ01750312 port of SCGCQ01739092) 
 - eHBA Personality: RAID Level Migration on Simplified R10 fails(SCGCQ01750316 port of SCGCQ01747188) 
 - READ CAPACITY 16) Is Working For All Values of SERVICE ACTION Field(SCGCQ01753395 port of SCGCQ01724697) 
 - F/W Hangs during reboot(SCGCQ01757394 port ofSCGCQ01616551 ) 
 - Improve Aero CPU Intensive Workload Efficiency(SCGCQ01772474 port of SCGCQ01698190) 
 - HII reports "The requested command has invalid arguments" when attempting to change controller personality(SCGCQ01772484 port of SCGCQ01715394) 
 - FW stated number of disks exceeded the max supported count with 14 PD(SCGCQ01776087 port of SCGCQ01680522) 
 - Unexpected enclosure events seen during physical intervention(SCGCQ01776327 port of SCGCQ01764132) 
 - Unmap R5/6: Implementation supporting new API and logic(SCGCQ01789236 port of SCGCQ01760871) 
 - Secured R1 VD is no longer shown as secured after an OCR(SCGCQ01791039 port of SCGCQ01765153) 
 - [iMR7.5][Bristol] Amber LED doesn't turn on with PD offline(SCGCQ01798257 port of SCGCQ01767172) 
 - StorCLI - Aero PA-0.6: Snapdump properties default values different after disabling and re-enabling its feature(SCGCQ01802451 port of SCGCQ01789798) 
 - HII allows setting controller personality through Manage Controller Profile menu(SCGCQ01809004 port of SCGCQ01685583) 
 - eHBA mode/Controller montasks/ocrs when pulling VD, inserting vd importing the vd and trying to delete it.(SCGCQ01809091 port of SCGCQ01787470) 
 - HII reports "The requested command has invalid arguments" when attempting to change controller personality(SCGCQ01813388 port of SCGCQ01715394) 
 - [UNMAP]: VMWARE 6.5 U1 requires VPD Page B1 support for UNMAP feature(SCGCQ01816730 port of SCGCQ01563349) 
 - Removed log message that was impacting customer(SCGCQ01828388 port of SCGCQ01828314) 
 - Set ldRestriction appropriately in MFCD parameters and persistent config pages(SCGCQ01864195 port of SCGCQ01487406) 
 - 530-8i- iMR Controller crashes during IO DMA operation(SCGCQ01880814 port of SCGCQ01830392) 
 - Same EID assigned to 2 530-8i controllers(SCGCQ01892544 port of SCGCQ01883096) 
 - CIT: Same EID assigned to 2 930-8i controllers(SCGCQ01892548 port of SCGCQ01830180) 
 - Exposing Write cache as disabled to host for a performance improvement(SCGCQ01901468 port of SCGCQ01845298) 
 - Same EID assigned to 2 530-8i controllers(SCGCQ01903444 port of SCGCQ01883096) 
 - Secure LD Creation with Dedicate Hot spare fails(SCGCQ01907189 port of SCGCQ01890955) 
 - ICMR1 With Storlibtest (OOB(SCGCQ01914261 port of SCGCQ01909345) 
 - iMR global fault LED does not get lit up during fail or UBAD(SCGCQ01915782 port of SCGCQ01877036) 
 - Ctrl fail to response when OCR occur during R6 reconstruction.(SCGCQ01917872 port of SCGCQ01686659) 
 - Unmap setting is not getting enabled with the new NVDATA(SCGCQ01919539 port of SCGCQ01818568) 
 - Forcing rebuild of multiple drives while activity is occurring can have data misdirected to the wrong drive and hit an assertion.(SCGCQ01920097 port of SCGCQ01849986) 
 - OCR/KA (if OCR is disabled(SCGCQ01968461 port of SCGCQ01940516) 
 - 9460-8i:"Other Error Count" of drives increase when running dd test(SCGCQ01969749 port of SCGCQ01943742) 
 - SLT hangs, when user tries to fetch information about the Bad SAS PD(SCGCQ01993273 port of SCGCQ01848463) 
 - MCTP: Fault 0x265D when packet with StartOfMsg is set and PktSeqCount is 1(SCGCQ01966451 port of SCGCQ01850721) 
 - [Ventura][PL] Applications trying to update NVMe device Firmware with Mode E fails.(SCGCQ01868160 port of SCGCQ01624790) 
 - Ventura MSS: Multi-bit ECC, EFI SAS DRIVER issue seen when performed multi reboot stress from UEFI(SCGCQ01822452 port of SCGCQ01794025) 
 - PL support for monitoring sanitize operation after controller/device reset.(SCGCQ01753176 port of SCGCQ01591995) 
 - PL: Chassis Slot Valid Flag is Incorrectly Cleared in Enclosure Page 0(SCGCQ01715880 port of SCGCQ01715509) 
 - (SATA Only(SCGCQ01668674 port of SCGCQ01638248) 
 - Change detect feature support on UBM supported back plane(SCGCQ01628416 port of SCGCQ01605371) 
 - (SATA Only(SCGCQ01621654 port of SCGCQ01593136) 
 - (SATA Only(SCGCQ01615216 port of SCGCQ01598756) 
 - Race condition can allow IOs over OOB to removed drive, with no host IOs, to not be cleaned up, and possibly leading to new(SCGCQ01605489 port of SCGCQ01400110) 
 - pl: NVMe: Write Long (10(SCGCQ01601702 port of SCGCQ01593652) 
 - pl: backend PCIe: potential address range overlap(SCGCQ01592870 port of SCGCQ01586393) 
 - PL: Revised "Avoid Duplicate Mid" Feature Code Could Incorrectly Allow IO to Start Through PL Firmware Path(SCGCQ01559005 port of SCGCQ01520524) 
 - IOP: FW to clear all pending PCI interrupts during a Function Level Reset (FLR(SCGCQ01534881 port of SCGCQ01523541) 
 - pl: NVMe: PCIe reconfiguration may occur during NVMe controller reset(SCGCQ01527219 port of SCGCQ01526236) 
 - (SATA Only(SCGCQ01524638 port of SCGCQ01275335) 
 - pl: backend PCIe: 4311 fault with NVMe enabled(SCGCQ01520574 port of SCGCQ01514521) 
 - Cache data lost event seen for WT vds(SCGCQ01334347 port of SCGCQ01313607) 
 - Learn cycle shown as active when Learn cycle fails(SCGCQ01403968 port of SCGCQ01400807) 
 - Not all internal backplane drives are getting an enclosure ID when Insights are zoned to the controller(SCGCQ01567525 port of SCGCQ01538817) 
 - Not able to import foreign configuration when pinned cache is present(SCGCQ01568092 port of SCGCQ01539920) 
 - RMU reports NO_BATT Missing when checking battery status after jumper has been removed(SCGCQ01568394 port of SCGCQ01553947) 
 - VMware Passthrough Adapter does not sync time on VM power on(SCGCQ01595864 port of SCGCQ01592800) 
 - Kill Adapter while running IOs on 64 VDs (including slice VDs(SCGCQ01601287 port of SCGCQ01548019) 
 - AULBA divert bitmap not enabled on R5/R6 WT Vds(SCGCQ01627798 port of SCGCQ01619858) 
 - COL ONFI Single Image support was broken with onfiValidateCSCount changes(SCGCQ01679087 port of SCGCQ01675779) 
 - Firmware hangs during boot(SCGCQ01679094 port of SCGCQ01665148) 
 - Drives are reverted back to JBOD after perfoming instant secure erase(SCGCQ01683365 port of SCGCQ01615777) 
 - Data Corruption seen on NVME drives with Medium Errors(SCGCQ01714207 port of SCGCQ01665227) 
 - [iMR7.5] Memory allocation failure during RAID operation cycles under high loading(SCGCQ01727274 port of SCGCQ01697700) 
 - When patrol read completed with Talladega 9460-8i and MR7.5 components, the customer saw Patrol read complete events were(SCGCQ01746344 port of SCGCQ01732235) 
 - With a pending personality change, Global hot spares are allowed to be created and should be blocked.(SCGCQ01750314 port of SCGCQ01742187) 
 - REPORT LUNS Command is Not Failed for Unsupported "SELECT REPORT" Field(SCGCQ01753394 port of SCGCQ01719283) 
 - MR FW: Select SAS1/PDB1 BISR group by setting BisrSmsG = 0x0C in BISR Control register during Initial Power Up.(SCGCQ01762272 port of SCGCQ01614205) 
 - [Bristrol] [MR7.4] "Previous Configuration missing" occurs during reboot test with CC running(SCGCQ01765212 port of SCGCQ01697887) 
 - Allow user to force switching mode when configuration is present(SCGCQ01772483 port of SCGCQ01732059) 
 - CLI is not failing "set personality behavior=None/JBOD"(SCGCQ01776335 port of SCGCQ01764921) 
 - fixed exception at medium error recovery caused by a bad drive.(SCGCQ01826256 port of SCGCQ01807457) 
 - Increase the recon BB list entries to align with BBM MAX BAD entries(SCGCQ01851104 port of SCGCQ01623254) 
 - Line 535 in ../../raid/cachePreserve.c for trying to create Pinned Cache by Cable Pull.(SCGCQ01878338 port of SCGCQ01839662) 
 - Error restoring offloaded (single image controller(SCGCQ01885343 port of SCGCQ01826923) 
 - Legacy BIOS Prints "This firmware is a TEST version"(SCGCQ01901447 port of SCGCQ01825992) 
 - Only Detect 63 Drives in Mix mode enviroment (Total 64 PDs in the system(SCGCQ01917261 port of SCGCQ01885194) 
 - Reconstruction R1 to R5 by adding a pd found a drive of R1 became unconfig bad(SCGCQ01919532 port of SCGCQ01819285) 
 - FW hit "failed element size check !! ... tail pointer 65535 exceeds max 255" while OCR and rebuilding in loop(SCGCQ01920090 port of SCGCQ01886840) 
 - Secure LD Creation with Dedicate Hot spare fails(SCGCQ01929133 port of SCGCQ01890955) 
 - MR_7.8:Driver unload and leave the system overnight, result to Assertion(SCGCQ01949646 port of SCGCQ01889482) 
 - log dump all command not working on Ventura controllers(SCGCQ01978876 port of SCGCQ01937037) 
 - Ventura PL: Check in Revised Workaround for 0x5842 fault - Rx Dma Memory Overflow(SCGCQ01967432 port of SCGCQ01864843) 
 - vSES: Remove, RRAbort and Missing bits in array device element are not getting updated in element status page.(SCGCQ01967385 port of SCGCQ01932394) 
 - [vSES] Vendor ID and Product ID of Configuration diagnostic page uses hardcoded values.(SCGCQ01906460 port of SCGCQ01906013) 
 -(SCGCQ01748041 port of SCGCQ01615484) 
 - (SATA only) Self-test offline immediate status received from drive is not populated to SCSI log sense command.(SCGCQ01714280 port of SCGCQ01681441) 
 - PL: (SATA Only)SSU Command for active power condition transition on EPC enabled drive fails with Additional sense Logical block address out of range(SCGCQ01640974 port of SCGCQ01640762) 
 - pl: NVMe: unexpected target reset task management timeout(SCGCQ01587064 port of SCGCQ01580026) 
 - Get VDM Support command does not have VendorID and VendorAddInfo fields properly populated(SCGCQ01530305 port of SCGCQ01450475) 
 - Intermittent: On iMR_Invader & cascaded Enclosures, after power off the enclosure, FW holds the PD info and apps display PDs(SCGCQ01503911 port of SCGCQ01483727) 
 - Enable and implement missing interrupts in the PCE core(SCGCQ01596697 port of SCGCQ01537812) 
 - DISM - Assertion failure in ../../dm/src/devRemoval.c for breaking multipath during bootup(SCGCQ01635256 port of SCGCQ01618628) 
 - FW can lose AltSel and DrvStrength(SCGCQ01679098 port of SCGCQ01635796) 
 - Too many Unexpected Sense : "1/0/1d " logged for SATA drives(SCGCQ01722276 port of SCGCQ01714261) 
 - Cisco - CSCvh78916 - Copyback to GHS/DHS target drives returns inappropriate error message in some invalid scenarios(SCGCQ01731365 port of SCGCQ01590213) 
 - Event with invalid slot # during pd insertion when a command is timed out(SCGCQ01732411 port of SCGCQ01721492) 
 - Unable to see the Background progress tab in LSA while Patrol read operation is running(SCGCQ01753392 port of SCGCQ01676417) 
 - FW crash observed while reinserting drives part of TR drive group after reboot(SCGCQ01763188 port of SCGCQ01763071) 
 - SBR version is not shown in the cli show all output in eHBA mode(SCGCQ01763492 port of SCGCQ01729855) 
 - Attempting to secure a 3rd party locked SED EPD fails but applications report success.(SCGCQ01763496 port of SCGCQ01747590) 
 - 3108 firmware reports Unexpected Sense Error" LBA Out of Range when running Sg util(SCGCQ01763951 port of SCGCQ01749090) 
 - No profile reported when a bad (0-byte(SCGCQ01914532 port of SCGCQ01897779) 
 - Assertion is hit during region lock release due to inconsistent region lock promotion related variables(SCGCQ01915567 port of SCGCQ01863948) 
 - Eliminate a storm of AR deletion activity with max-configuration when ten enclosures are shut off(SCGCQ01920037 port of SCGCQ01841657) 
 - Secure erase on JBOD drives using hdparam is failing sporadically(SCGCQ01929056 port of SCGCQ01904220) 
 - Issue: MR FW asserted after copyback completed and the source drive was removed.(SCGCQ01940107 port of SCGCQ01921307) 
 - Error LED cannot stay long when drive pulled from VD.(SCGCQ01944350 port of SCGCQ01882216) 
 - (SATA Only(SCGCQ01731910 port of SCGCQ01638248) 
 - FW logging fatal error in case of chip reset, but driver not loaded.(SCGCQ01623751 port of SCGCQ01594199) 
 - Incorrect event message when CC is suspended after processing uncorrectable media errors.(SCGCQ01683352 port of SCGCQ01579614) 
 - Reduce bootup time by 15-20 seconds(SCGCQ01892778 port of SCGCQ01735563) 
 - The SUT can’t boot to OS after 159 loops AC cycle and check the Raid 930-16i 8G(SCGCQ01902777 port of SCGCQ01788479) 
 - 530-8i- iMR Controller crashes during IO DMA operation(SCGCQ01911311 port of SCGCQ01830392) 
 - Firmware ASSERT(SCGCQ01911892 port of SCGCQ01729837) 
 - Forcing rebuild of multiple drives while activity is occurring can have data misdirected to the wrong drive and hit an assertion.(SCGCQ01912487 port of SCGCQ01849986) 
 - When checking the config sequence number mismatch, need to cover system PDs.(SCGCQ01914298 port of SCGCQ01871037) 
 - Critical Message " maximum supported count of 256 disks" received with MaX PDs(SCGCQ01918227 port of SCGCQ01884237) 
 - CSCvm32376 - Fatal firmware error: Line 120 in ../../raid/utils.c(SCGCQ01919551 port of SCGCQ01895764) 
 - MR_7.8: Fail to perform OCR , after FW upgrade from MR 7.7 to 7.8(SCGCQ01936411 port of SCGCQ01823917) 
 - With the IMR controller IOMMU fault is observed with the latest driver allow both RDPQ array or linear array.(SCGCQ01942615 port of SCGCQ01928086) 
 - Fix Alignment of ENCL_INFO struct members in 7.8(SCGCQ01945684 port of SCGCQ01905512) 
 - foreign import failed when sequence number mismatch(SCGCQ01968758 port of SCGCQ01912560) 
 - Aero PA0.5: FW fails to create VD in Profile 12 when you have 208 VD's and you delete 16 VD's and try to create 16 more VD's(SCGCQ01787902 port of SCGCQ01761452) 
 - 9440-8i / 9460-16i cards BCA_S LED state doesn't match with BCA-S LED Behavior Rule.(SCGCQ01902766 port of SCGCQ01832279) 
 - limit target queue depth not greater than controller queue depth(SCGCQ01920041 port of SCGCQ01841594) 
 - Cannot be done initialize even if execute Full Initialize by using StorCli(SCGCQ01968776 port of SCGCQ01938067) 
 - DC observed on one of the R1 VD, after degrading the R1 DG(SCGCQ01714692 port of SCGCQ01676617) 
 - LSA version 4.132 shows blank page or extreme sluggish to do anything(SCGCQ01715426 port of SCGCQ01698418) 
 - BMC emulator does not load storelibTest(SCGCQ01849642 port of SCGCQ01762267) 
 - Investigate on unalligned IO's for 512E drives with background operation(SCGCQ01866862 port of SCGCQ01181178) 
 - Aero BST failure, Raid LD tgtId does not persist through OCR(SCGCQ01873049 port of SCGCQ01857416) 
 - CIT: Same EID assigned to 2 930-8i controllers(SCGCQ01902802 port of SCGCQ01830180) 
 - Check NULL pointer in display function called by snapdump to avoid data abor exception(SCGCQ01914622 port of SCGCQ01892152) 
 - DDF corruption after hibernation because of incorrect virtual address mappings(SCGCQ01916718 port of SCGCQ01877879) 
 - MR7.7: FW hit Assertion failure in fw\raid\mpthostcmd.c at line 1951: DMGetSpanFromDevhandle(pMpt->DevHandle(SCGCQ01917260 port of SCGCQ01763331) 
 - Handle missing changes of CSET(SCGCQ01318495(SCGCQ01919498 port of SCGCQ01904051) 
 - copyback fail to start on some PDs(SCGCQ01919504 port of SCGCQ01839637) 
 - Aero PA0.7: FW breaks into montask with exceptional core handling error(SCGCQ01919585 port of SCGCQ01850596) 
 - On ESXi6.7U1 OS, With the IMR controller IOMMU fault is observed with the latest driver(SCGCQ01929982 port of SCGCQ01893479) 
 - host issued UNMAP cmd not handled properly when VD is offline(SCGCQ01940967 port of SCGCQ01920370) 
 - MR7.8 OEM: WT VD created on attempt to create WB VD(SCGCQ01942129 port of SCGCQ01916098) 
 - MR7.8 PA2: Security property is always shown false for a DG when Secured VD is created via LSA in SLES 15(SCGCQ01942543 port of SCGCQ01848923) 
 - MR_7.8: During system reboot IMR card logged an event "log discontinuity due to buffer full"(SCGCQ01978900 port of SCGCQ01872802) 
 - Kill Adapter while running IOs on 64 VDs (including slice VDs(SCGCQ01601265 port of SCGCQ01548019) 
 - MR7.8: While doing SED JBOD drive pull on iMR, FW hit Assertion failure in fw\dm\pl3.5\pliopi.c at line 1164: 0(SCGCQ01915852 port of SCGCQ01876358) 
 - Aero PA0.6: FW "Assertion failure in fw\raid\mon.c at line 650: 0" encountered when 2 R5 VDs go offline(SCGCQ01917259 port of SCGCQ01816635) 
 - Heavy MFI based LD IO writes during POST causing WJ entries exhaust on iMR and FW asserting(SCGCQ01942509 port of SCGCQ01930815) 
 - Fw hit drvspinup.c when wake up from hibernation(SCGCQ01948887 port of SCGCQ01912208) 
 - undo previous fix; previous fix introduces undesirable side effects(SCGCQ01966532 port of SCGCQ01932051) 
 - Data Abort Exception on abrupt powerloss/reset when flushing events from NVRAM hold buffer to flash(SCGCQ01996623 port of SCGCQ01973389) 

EnhancementRequests:
 - Add MR API bit to indicate the profile is NVMe Only profile(SCGCQ01216848) 
 - SATA SMR Only : Change for the FORMAT UNIT translation for SMR drives to also call RESET WRITE POINTER with ALL bit set(SCGCQ01218300) 
 - New events for PR/CC conflicts and sector size mismatch(SCGCQ01227051) 
 - Add Aero workaround matrix(SCGCQ01376462) 
 - Add Aero custom file(SCGCQ01376466) 
 - Add PLI Control Request to Fully Pause/Unpause FPE HW(SCGCQ01378809) 
 - Aero-3: CR#06: SPILib: Add necessary SPI timings to Aero/Sea to support multiple SPI Vendors(SCGCQ01380051) 
 - Aero-3: Update Clock, Configuration, and Reset (CCR(SCGCQ01380109) 
 - perform SED reauthentication if secured PD is managed by FW when DMD occurred(SCGCQ01403487) 
 - Incorporate new PHY register initialization settings.(SCGCQ01405307) 
 - Aero DDR: PHY based Read Leveling(SCGCQ01405427) 
 - Aero DDR: PHY based Write Leveling(SCGCQ01405430) 
 - Aero: Internal Boot ROM Support(SCGCQ01410019) 
 - Aero:Add Pocono support to Aero(SCGCQ01412204) 
 - Add Aero checkword(SCGCQ01427566) 
 - Add Test Link Diagnostic API(SCGCQ01436268) 
 - Merge RMW IOPs Performance POC into Aero Stream(SCGCQ01437148) 
 - pl: backend PCIe: add API for getting backend PCIe link configurations(SCGCQ01437182) 
 - Add MSS reset back to Aero(SCGCQ01444943) 
 - Re-enable flash initialization in bootloader.(SCGCQ01448314) 
 - Provide OEMs ability to select either I2C or PCIe as an out of band transport(SCGCQ01450245) 
 - (SATA Only(SCGCQ01452113) 
 - Add method to determine Ring Buffer Overflow in RMC.(SCGCQ01458368) 
 - Disable break/join mirror(SCGCQ01464239) 
 - Block RLM(SCGCQ01464241) 
 - Aero simplification (PA-0.2(SCGCQ01464242) 
 - Cache Policy VD Parameter Changes(SCGCQ01465089) 
 - Aero simplification (PA-0.5(SCGCQ01465430) 
 - MegaRaid VT BootLoader Flash Map Update For Ventura(SCGCQ01467197) 
 - TGC Opal Support(SCGCQ01472524) 
 - New command issued from StorCliF to test PHYs during Manufacturing only.(SCGCQ01473896) 
 - Move flash code region alias(SCGCQ01494503) 
 - opal drive support(SCGCQ01498086) 
 - Aero-3: Create framework for M0 processors(SCGCQ01499419) 
 - Add support for mr build to get bin using fromelf(SCGCQ01501207) 
 - Ability for UEFI/HII to log debug messages to UART(SCGCQ01501987) 
 - SAS3.5 (SATA Only(SCGCQ01503732) 
 - Need version info in binary(SCGCQ01504281) 
 - Rebase Aero3 Development Stream and Verify Ventura Functionality(SCGCQ01509806) 
 - Ventura: Add MCTP over I2C Master Mode Option that doesn't use I2C DMA(SCGCQ01516871) 
 - Limit scope of supported drives (SAS/SATA(SCGCQ01517627) 
 - FW OCR debug mechanism(SCGCQ01520445) 
 - MR 7.6: Opal: Use Locking SP to read and write key info from Scratch Pad (DataStore(SCGCQ01521540) 
 - Enable Backplane Management based on backplane type signal per HBA connector quad(SCGCQ01524982) 
 - Evaluate usage of IEEE SGL pool for holding PRP list in the buffered PRP path(SCGCQ01525817) 
 - pl: NVMe: add NVMe task management test code(SCGCQ01526049) 
 - Handle PRP creation in RMW_CTIO path for IOLength more than 20KB(SCGCQ01529120) 
 - Increase SRAM_Fixed IOPATH Code Size(SCGCQ01529611) 
 - Ventura: Specify leading zeros for the prints using %x in pl diag module(SCGCQ01533485) 
 - Aero-3: Update RMC FW to follow the steps from Aero SOC uArch spec(SCGCQ01533491) 
 - Enable and implement missing interrupts in the PCE core(SCGCQ01537812) 
 - Evaluate GPIO usage from NVData in FW(SCGCQ01538673) 
 - Add ApSHA hardware header(SCGCQ01538919) 
 - Add a new flag to IoFlags in pliStartScsiIo(SCGCQ01544740) 
 - Ventura: Ensure new I2C non_DMA code compiles with MCTP disabled(SCGCQ01548925) 
 - Remove ENET(Ethernet support Bit 26(SCGCQ01555034) 
 - [UNMAP] 7.6 : SSD's which doesn't support UNMAP gets kicked in as GHS/EGHS even if there are UNMAP supported drives(SCGCQ01556699) 
 - Changes to Core 1 boot sequence(SCGCQ01557091) 
 - Vision Support for downloading firmware image(SCGCQ01558118) 
 - Remove CSW library from AERO builds(SCGCQ01558186) 
 - Compress Debug Data and store to DRAM persistent AREA(SCGCQ01558509) 
 - Cache offload/Restore changes to preserve data across OCR, Power cycle(SCGCQ01558545) 
 - Different SED type mix in an array(SCGCQ01558907) 
 - DDR version of Firmware Renamed Signals and GPIOs(SCGCQ01561073) 
 - Create additional build target(SCGCQ01564859) 
 - Assert triggers snapdump(SCGCQ01565492) 
 - Change the default behavior for I2C MCTP to non-DMA(SCGCQ01565737) 
 - ALADIN cold boot support for Ventura(SCGCQ01566074) 
 - Intruder: Modify NVDATA to enable DMA by default(SCGCQ01566619) 
 - Add slave bypass support(SCGCQ01567489) 
 - Implement Snapdump debugging capability(SCGCQ01567770) 
 - Add capability to report to Host Software Application the Drive SED Type(SCGCQ01570280) 
 - Add new parameter in NVDATA to enable/disable mix of Opal & Enterprise SED drives in security enabled array(SCGCQ01570611) 
 - Add Aero FW secret(SCGCQ01571726) 
 - Disable licensing backdoors(SCGCQ01571783) 
 - Add make support(SCGCQ01572146) 
 - Add multithreaded elftobin(SCGCQ01572366) 
 - Update build to calculate build duration(SCGCQ01572912) 
 - De-tune RMW CTIO Enhancements for Non-Aero (3916(SCGCQ01573051) 
 - Debug integration across modules(SCGCQ01573078) 
 - BIOS Handshake breaks Manufacturing Environment, need change in TTY and/or add timeout in FW for BIOS Handshake(SCGCQ01575182) 
 - Ventura: Specify leading zeros for the prints using %x in plDebugStrings(SCGCQ01576200) 
 - Add support to detect drive with TCG Opalite or TCG Pyrite capable and convert it to non-SED drive(SCGCQ01576988) 
 - MR7.8: Multiple snapdump support(SCGCQ01579214) 
 - Extend debug framework to capture failures that doesn't involve a FW crash(SCGCQ01579219) 
 - Add support to defeature Cached I/O policy(SCGCQ01581032) 
 - pl: NVMe: add support for Security Protocol In/Out INC_512 flag(SCGCQ01582520) 
 - Disable mapping of some device side PCIe hardware into CPU's virtual address space(SCGCQ01582599) 
 - DC Debug Framework (NvMe(SCGCQ01583215) 
 - Add support for API fields to report SED type of PD(SCGCQ01587230) 
 - Enhance mptDirectLoopback for taskadd based to timer based.(SCGCQ01587438) 
 - Add critical boot messages for OCM ECC errors(SCGCQ01592807) 
 - Add OnOff parameter in Properties2 of Structure MR_CTRL_PROP to enable/disable mix of Enterprise & Opal SED drives(SCGCQ01593520) 
 - MR API change request to Enable/disable the parallel PD FW update feature based on PNP ID’s(SCGCQ01595347) 
 - Debugging infrastructure to detect dynamic memory Memory Corruption And Memory Leaks(SCGCQ01595603) 
 - Aero-3: Modify CBB build so that it decreases the hardware reserved area (SBR(SCGCQ01595798) 
 - New configuration params added for EPD-PT devices(SCGCQ01599607) 
 - Separate Aero and Ventura builds(SCGCQ01600799) 
 - Add basic version information for Vision(SCGCQ01601700) 
 - Update DDR version FW according to Aero SuperCap management(SCGCQ01602431) 
 - NVDATA parameter to OPAL SED(SCGCQ01607938) 
 - [MR 7.7] UNMAP/TRIM/WRITESAME for EPDs in JBOD personality & JBODs in RAID personality(SCGCQ01608027) 
 - RMC must add PCE PLL/Core Initialization for Secure Mode(SCGCQ01608224) 
 - Enable Support for VSES Interface and device enumeration behind PCIe switch in MR FW(SCGCQ01614212) 
 - Aero-3: Review Aero Impala changes(SCGCQ01614623) 
 - Aero: backend PCIe: update config pages for 16GT/s(SCGCQ01614647) 
 - 7.5 R1 performance change request.(SCGCQ01614688) 
 - NVDATA parameter to OPAL SED(SCGCQ01614689) 
 - Add new files to build scripts(SCGCQ01615521) 
 - Flag added in AERO to avoid sending IO requests to IOA NVMe core that could potentially cause exceptions(SCGCQ01615545) 
 - Set feature simplification(SCGCQ01616881) 
 - Remote Flash utility for Avenger.(SCGCQ01618931) 
 - Aero: enable backend PCIe support in the Aero build(SCGCQ01619936) 
 - Added a new interface between driver-aops to indicate if 64 bit SGL support is enabled(SCGCQ01620350) 
 - Modify event string APIs for MISSING and OFFLINE LDs(SCGCQ01628177) 
 - pl: backend PCIe: basic PCI hot plug power controller support for switches(SCGCQ01633888) 
 - Aero DDR: DDR library initialization on the FPGA(SCGCQ01634738) 
 - Enable Profile 14, 24 NVMe drive support for 3516 based design(SCGCQ01634874) 
 - Remove SERIES_3108 from mptDirectFuncs.c(SCGCQ01635731) 
 - Aero simplification (PA-0.5(SCGCQ01638223) 
 - pl: NVMe: remove vendor specific prototype code(SCGCQ01638257) 
 - Add new MFI Status to block requested operation due to existing controller configuration(SCGCQ01670135) 
 - Change the mr.h API comment showing the new return status for the - MR_DCMD_PD_GET_INFO(SCGCQ01670234) 
 - pl: NVMe: support for nonzero doorbell stride(SCGCQ01670300) 
 - Re-tune RMW CTIO Enhancements for F_AERO_ON_VENT Builds(SCGCQ01675552) 
 - 7.7 Manage SGPIO through VSES only if PCI switch is detected(SCGCQ01676604) 
 - Enable Profile 14, 24 NVMe drive support for 3508 based design(SCGCQ01676990) 
 - SPI_LIBRARY: Aero/Ventura Provide Sufficient Information to Uniquely Detect Auto-Configured devices(SCGCQ01679097) 
 - API change for Switch attached NVMe HW RAID support for Supermicro backplanes(SCGCQ01697667) 
 - Storcli Output after Vision PSOC FW update, Change to power cycle instead of reboot(SCGCQ01698424) 
 - Create sanitize events(SCGCQ01713708) 
 - Improve build times(SCGCQ01715410) 
 - Fine Tune iMR RAID IO path performance(SCGCQ01715637) 
 - Add debug print for unrecognized initial FIS(SCGCQ01718317) 
 - Permit multiple calls to avSerdesSASSDAddTxEqSeq and implement aviSerdesSASSDWaitIntrSmIdle for SAS35XFW(SCGCQ01720492) 
 - Honor the RAID key disk count and modify the profile information so it gets displayed accurately.(SCGCQ01727239) 
 - API changes needed to support eHBA product series(SCGCQ01727346) 
 - Aero: Move RSA defines in mpi_temp.h to a common area(SCGCQ01727399) 
 - MR FW change to support API change of new enclosure subtype for switch attached NVMe backplanes(SCGCQ01729976) 
 - RTTrace API Changes(SCGCQ01745568) 
 - FW changes for mixing Rules for SED and non-SED drives to create non-secure array with controller security enabled.(SCGCQ01750328) 
 - Mixing Rules for SED and non-SED drives to create non-secure array with controller security enabled.(SCGCQ01757538) 
 - Unmap: Define new API for enhanced UNMAP support(SCGCQ01758062) 
 - Criteo: API changes reversal(SCGCQ01760512) 
 - Unmap R5/6: Implementation supporting new API and logic(SCGCQ01760871) 
 - ComboSerdes: add APIs for firmware coordination with the protocol cycler(SCGCQ01761386) 
 - Adding API bit to indicate whether forced personality change is supported or not.(SCGCQ01762153) 
 - API Changes - After Vision PSOC FW update, applications should ask the user for power cycle instead of reboot(SCGCQ01765150) 
 - COL PRIV API changes(SCGCQ01765281) 
 - Support added to create simulated physical or virtual drive(SCGCQ01778289) 
 - Unmap R5/6: implement latest LD unmap policy, etc.(SCGCQ01789796) 
 - Including The Time Stamp for every Snap Dump created in the firmware.(SCGCQ01797424) 
 - Unmap: Define new events for enhanced UNMAP support [MR7.8](SCGCQ01803319) 
 - Unmap R5/6: Implementing new events for enhanced unmap support(SCGCQ01809217) 
 - Deprecate the snap dump fields that are no longer needed for MR_SNAP_DUMP_PROPERTIES structure(SCGCQ01816724) 
 - Exposing Write cache as disabled to host for a performance improvement(SCGCQ01845298) 
 - Tune DDR settings for OEM's custom design(SCGCQ01898339) 
 - Enable DDR debug reads(SCGCQ01321760) 
 - Warning removal 111(SCGCQ01346729) 
 - MR_FW_BLD_TOOLS: Add output file switch to RomEnv(SCGCQ01347456) 
 - Convert Aero build to Aero3(SCGCQ01349949) 
 - Aero: Design and Develop DDR Training Failure Debug infrastructure.(SCGCQ01367005) 
 - Aero Fpga support(SCGCQ01367141) 
 - Warning removal 1215(SCGCQ01389575) 
 - Initial release build support(SCGCQ01392130) 
 - Aero-3: Update ARM CPU Speed to 1600 MHz(SCGCQ01392205) 
 - Aero: Add 300MHZ UART Clock Reference Support(SCGCQ01392831) 
 - Release script changes for PA 1(SCGCQ01393659) 
 - Aero3: Add secure boot specified header and add support in rom utilities for it(SCGCQ01399079) 
 - Define an API for getting PDB HW configurations(SCGCQ01407350) 
 -(SCGCQ01418823) 
 - Implement Dynamic Flash Size - use the flash pagesize and blocksize.(SCGCQ01458603) 
 - Provide API changes to let driver know of EPD volumes and flags to take better decision on MDTS(SCGCQ01459293) 
 - Update PL version check(SCGCQ01464907) 
 - Offload division to driver(SCGCQ01470712) 
 - DC Debug Framework(SCGCQ01473145) 
 - Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01473898) 
 - Review Ventura MCTP workarounds(SCGCQ01484422) 
 - PL: Create defines for plRequestFWBreak((SCGCQ01499053) 
 - Change pceDumpRateInfo to support Gen4 Speed(SCGCQ01501529) 
 - Add parsing of real time info for RMC logging(SCGCQ01507161) 
 - Disable PCIe switch support in 7.6(SCGCQ01508256) 
 - Aero-3: Ensure modifed SBR template data is compatible with Ventura(SCGCQ01509915) 
 - Support for NVDATA control of static slot number assignments for x2 or x4 NVMe devices(SCGCQ01511787) 
 - Ventura: Use non-DMA option for MCTP over I2C - Slave Mode(SCGCQ01516865) 
 - MR 7.6: Opal: Add Revert TPer (Device(SCGCQ01518205) 
 - Ventura: Add symbol names to "iop show gic"(SCGCQ01519283) 
 - Remove inc flags from the via file(SCGCQ01521426) 
 - Add OCE support bit(SCGCQ01524705) 
 - FPGA Build Support(SCGCQ01525486) 
 - Get Random number from OPAL drive(SCGCQ01526167) 
 - OCM hardware header(SCGCQ01530394) 
 - Add OCM ECC scrub support(SCGCQ01531858) 
 - Added MR_MFC_DEFAULTS.NVMeAbortTO and MR_MFC_DEFAULTS.NVMeMaxControllerResetTO(SCGCQ01532045) 
 - PCIe Switch attached NVMe Backplane LED Management support(SCGCQ01532296) 
 - Aero R5 RMW CTIO IOPs Performance POC Part 2(SCGCQ01534468) 
 - Add TRNG hardware header(SCGCQ01537996) 
 - SRK hardware header(SCGCQ01538683) 
 - NVME Task Management Change 3.(SCGCQ01538729) 
 - Disable support for UNMAP on SATA drives due to unavailability of ZEROEXT (TRIM=1(SCGCQ01552670) 
 - Add I2C header changes(SCGCQ01553011) 
 - Update FC Div handling(SCGCQ01556172) 
 - Add handling for CCR_RST_DEBUG_CNTRS(SCGCQ01558173) 
 - Vendor Semi APIs(SCGCQ01558218) 
 - Support for collection of ARM instruction trace(SCGCQ01565490) 
 - Add Margay expander recognition to Ventura(SCGCQ01570647) 
 - ARM PMU Sampling framework(SCGCQ01571034) 
 - Support NVData control of static mapping for slot numbers of x2 or x4 devices (or x2 or x4 plumbing(SCGCQ01574963) 
 - Allow filtering of NVMe exception prints in debug mask(SCGCQ01575138) 
 - Make the new NVME Write Uncorrectable cmd working fully for future MR 7.x release.(SCGCQ01580013) 
 - iMR IO path adjustment(SCGCQ01588780) 
 -(SCGCQ01598929) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_7.0 - 06.250.04.00 MR PL-SCS Libs from new PL source stream(SCGCQ01599753) 
 - pl: NVMe: more NVMe TM test code(SCGCQ01605900) 
 - pl: backend PCIe: merge extended capability search functions(SCGCQ01613997) 
 - PL SATL: ZNR bit translation during SCSI SANITIZE command for SMR drive(SCGCQ01615513) 
 - Delete strings that are not used in plDebugStrings(SCGCQ01620668) 
 - Support more than 16Mb transfer with SysDma(SCGCQ01623953) 
 - Update file headers with Broadcom copyright(SCGCQ01631051) 
 - Suppress license warnings(SCGCQ01641063) 
 - Add FW support for MPI Comp Img (SB(SCGCQ01685811) 
 - Improve Aero CPU Intensive Workload Efficiency(SCGCQ01698190) 
 - Verify that the Statistics from 57 Pages of NAND Parameters can be read.(SCGCQ01735503) 
 - Reduce bootup time by 15-20 seconds(SCGCQ01735563) 
 - Aero: backend PCIe: basic Atlas host interface board bringup(SCGCQ01736527) 
 - Improve NVRAM performance(SCGCQ01750319) 
 - Enable ONFI Dual COL Image support for OEM(SCGCQ01753457) 
 - MR FW Aero uses RMC GPIO to enable Battery on SOD in RMC. Exclude Battery Enable changes for specifc OEM in MR FW.(SCGCQ01753459) 
 - Aero PA0.5: Handling false BIOS message logging in Jbod personality(SCGCQ01757480) 
 - OOB Auto DevBST(SCGCQ01763421) 
 - Unmap R5/6: Firmware downgrade scenario(SCGCQ01765607) 
 - Incorporate the changes needed by PL to NVDATA(SCGCQ01790860) 
 - Add support for Gas Gauge parts "sn33100"(SCGCQ01818346) 
 - Read-only TLB support(SCGCQ01315602) 
 - MR_FW_BLD_TOOLS: Update to sas2parser version 10.05.00.00(SCGCQ01347713) 
 - Ventura/Marlin: Detect attempt to downgrade from auto-detected SPI parts to non-auto and fail(SCGCQ01449329) 
 - Add User0 support to Main FW(SCGCQ01453208) 
 - PL: Use Sense Data from SATA Log Page 10 when querying Log Page 10(SCGCQ01459375) 
 - AERO Debug Framework Enhancements - Basic Framework(SCGCQ01473143) 
 - Safe Mode instead of early boot crash(SCGCQ01473148) 
 - Gas Gauge Code Cleanup(SCGCQ01482377) 
 - Aero: backend PCIe: modify outbound address window configuration(SCGCQ01485166) 
 - Opal Drive support(SCGCQ01487401) 
 - Add CHECKED_ASSERT for Detecting RMC Watchdog Occurrences from MR(SCGCQ01501362) 
 - NVME : Task Management Part II(SCGCQ01517088) 
 - 7.6 NVDATA change for ManPage11 NVMeAbortTO(SCGCQ01525177) 
 - Add OCM Correctable ECC error injection(SCGCQ01531845) 
 - Add OCM uncorrectable ECC error injection(SCGCQ01531847) 
 - Ventura: Modify DMAless-I2C MCTP code so that that it processes most data in interrupts(SCGCQ01533036) 
 - Update CCR header(SCGCQ01553014) 
 - Add latest CCR headers(SCGCQ01553034) 
 - Add developer library builds(SCGCQ01553099) 
 - Check BISR register changes(SCGCQ01556842) 
 - Changes to CCR_AVSO_EFUSE_READ_CONTROL(SCGCQ01556978) 
 - Snapdump API implementation(SCGCQ01561812) 
 - [UNMAP]: VMWARE 6.5 U1 requires VPD Page B1 support for UNMAP feature(SCGCQ01563349) 
 - Update Aero UART dividers properly(SCGCQ01566425) 
 - Add a temp parameter to elftobin(SCGCQ01572361) 
 - Update tcc to version 0.9.27(SCGCQ01593619) 
 - Remove NVRAM intercore for 3916(SCGCQ01602518) 
 - Integrate SAS3.5CtrlFw_Ventura_Ph_7.0 - 06.250.05.00 PL-SCS Libs(SCGCQ01607923) 
 - PL: Add NVDATA Option to Force Programmed Physical Link Rates to 0 in SMP Phy Control Request(SCGCQ01614814) 
 - VSES support for Direct Attached SGPIO backplane in JBOD personality.(SCGCQ01631254) 
 - MR 7.8 To incorporate SPI Library for IP Phase 9 to ensure multiple support for Winbond and ISSI at Aero GA(SCGCQ01665204) 
 - Ventura/Aero: (Child(SCGCQ01680542) 
 - Unmap R5/6: Changes related to rebuild/copyback/recon(SCGCQ01748174) 
 - Testability improvement for Cache Offload (COL(SCGCQ01753258) 
 - The SUT can’t boot to OS after 159 loops AC cycle and check the Raid 930-16i 8G(SCGCQ01788479) 
 - Persisting FW crash code for reporting through boot message for Shenandoah(SCGCQ01793712) 
 - Add multi Snapdump files transfer support from FW to Debug terminal through Zmodem(SCGCQ01802450) 
 - Opal Drive support in MR FW(SCGCQ01471518) 
 - Preboot OCR(SCGCQ01473151) 
 - Add method to determine Ring Buffer Overflow in RMC(SCGCQ01484941) 
 - Port OEM feature (Transport Ready(SCGCQ01507036) 
 - To implement the CHANGE_DETECT GPIO feature for the UBM backplanes(SCGCQ01507506) 
 - Aero-3: Modify the Aero3 build so that the main firmware image has a MPI Component Header(SCGCQ01509807) 
 - Request Mem32 resources from host(SCGCQ01523291) 
 - 7.6 NVDATA change for NVMeAbortTO in MrParamsPage0, and correct MrParamsPage0 XSD mapping.(SCGCQ01531782) 
 - Aero-3: Disable MCTP over PCIe VDM Workarounds(SCGCQ01533532) 
 - Ventura: Detect various user errors in firmware download(SCGCQ01534545) 
 - Add debug dump of memory locations when COL timeouts occur(SCGCQ01542428) 
 - aero3pce changes(SCGCQ01553134) 
 - Update RMC ring buffer parser with new timeout ID(SCGCQ01558231) 
 - Add MR_CTRL_INFO Bits to Differentiate Between Aero and Ventura FWs(SCGCQ01614207) 
 - Aero R5 RMW CTIO IOPs Performance Enhancements Part 3(SCGCQ01697664) 
 - Establish Aero build environment(SCGCQ01310265) 
 - Add all build variants to the build script(SCGCQ01349766) 
 - NVMe switch support(SCGCQ01471539) 
 - Use user1 in reset status register to indicate error state during offload sequence(SCGCQ01482387) 
 - Remove NVMe specific #defines(SCGCQ01501664) 
 - Fault LED behavior is not consistent between PD direct attached vs connected via expander(SCGCQ01508065) 
 - Move NVMe PRP specific code to a new file(SCGCQ01508197) 
 - Add zmodem support in the firmware(SCGCQ01527220) 
 - FW change for NVME API change.(SCGCQ01558166) 
 - SnapDump retrieval by user using a FW API(SCGCQ01558528) 
 - RMC manages EPAK_ENABLE(SCGCQ01561151) 
 - Add Aero XSD files including the MR defined config pages.(SCGCQ01641053) 
 - Man page 7 X2/X4 Slot overlap issue and fix(SCGCQ01675800) 
 - Ventura Debug Framework Enhancements Continuation Work(SCGCQ01680501) 
 - StorCLI/LSA show OEM NVMe switch with 32 slots instead of 12/24 physical slots(SCGCQ01683203) 
 - Update code identifiers to Broadcom(SCGCQ01733136) 
 - Implement module specific data dumps on ASSERT (using snapdump(SCGCQ01742061) 
 - MR FW return only compatible profiles(SCGCQ01789037) 
 - new FW and MegaMon interface to trigger SAS/SATA/NVME Analyzer(SCGCQ01817677) 
 - Do not discard the snap-dump on retrieval. Also include the time stamps during snap dump retrieval.(SCGCQ01822399) 
 - Change the order of DDF header updates when there are errors existing in DDF headers currently on the drive(SCGCQ01487403) 
 - Add uncorrectable DDR ECC error injection(SCGCQ01531838) 
 - Unmap/write-same(unmap=1,NDOD=1(SCGCQ01583563) 
 - Removing the unwanted debug prints(SCGCQ01896349) 


Version 50.5.0-1678 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:  7.05.02.2
	UEFI Driver: 0x07050404
	HII:   07.05.06.07
	MR FW: 5.050.00-1638
    package 50.5.0-1678
	
Defects (13)
- Fix compilation error in MR Pvt Api.(SCGCQ01619783)
- NVRAM: MR7.6 Vmware6.5 - Incorrect fatal error EVT after PassThrough enabled followed by Guest OS power on.(SCGCQ01600125)
- Nvram changes to Control Parallel Drive FW update via NVRAM variable for OEM - (SCGCQ01605609 CSET).(SCGCQ01617051)
- Patrol read restarts on PDs after completion on reboot.(SCGCQ01718200)
- When patrol read completed with Talladega 9460-8i and MR7.5 components, the customer saw Patrol read complete events were log.(SCGCQ01732235)
- Change the reserve field in structure mode param to follow spc4 spec.(SCGCQ01816426)
- dirty led not set on in case of supercap not present even though dirty cache is present.(SCGCQ01825031)
- 9440-8i / 9460-16i cards BCA_S LED state doesn't match with BCA-S LED Behavior Rule..(SCGCQ01832279)
- [iMR7.5][Bristol] Amber LED doesn't turn on with PD offline.(SCGCQ01767172)
- HDDs spin up failed during boot time and then cause ac cycle failed after around 70 power cycles.(SCGCQ01813023)
- Legacy BIOS Prints "This firmware is a TEST version".(SCGCQ01825992)
- CIT-Lenovo: Same EID assigned to 2 930-8i controllers.(SCGCQ01830180)
- CIT-: Same EID assigned to 2 530-8i controllers.(SCGCQ01883096)
- Make new copy of NVRAM for use with Aero.(SCGCQ01614114 port of SCGCQ01526096)
- Smart Return Status passthru command failed on SATA drives.(SCGCQ01802574 port of SCGCQ01802574)
- MR FW return only compatible profiles.(SCGCQ01809003 port of SCGCQ01789037)
- FW is not blocking switching to an unsupported profile.(SCGCQ01809222 port of SCGCQ01698176)
- HII allows setting controller personality through Manage Controller Profile menu.(SCGCQ01809004 port of SCGCQ01685583)
- HII reports "The requested command has invalid arguments" when attempting to change controller personality.(SCGCQ01813388 port of SCGCQ01715394)
- [UNMAP]: VMWARE 6.5 U1 requires VPD Page B1 support for UNMAP feature.(SCGCQ01816730 port of SCGCQ01563349)
- Set ldRestriction appropriately in MFCD parameters and persistent config pages.(SCGCQ01864195 port of SCGCQ01487406)
- [Bristrol] [MR7.4] "Previous Configuration missing" occurs during reboot test with CC running.(SCGCQ01765212 port of SCGCQ01697887)
- Increase the recon BB list entries to align with BBM MAX BAD entries.(SCGCQ01851104 port of SCGCQ01623254)
- 530-8i- Windows 2016 Dataceneter BSOD.(SCGCQ01880814 port of SCGCQ01830392)
- HDDs spin up failed during boot time and then cause ac cycle failed after around 70 power cycles.(SCGCQ01827311 port of SCGCQ01813023)
- BMC emulator does not load storelibTest.(SCGCQ01849642 port of SCGCQ01762267)
- The SUT can’t boot to OS after 159 loops AC cycle and check the Raid 930-16i 8G.(SCGCQ01788547 port of SCGCQ01788479)

EnhancementRequests (21)
- Added Timeout values to Target Device Properties.(SCGCQ01519777)
- Add build flags for Aero ROC.(SCGCQ01608149)
- Add a new parameter in MR Configuration Parameter Page 0 (NVDATA) to enable/disable parallel PD FW update feature.(SCGCQ01605140)
- Add a new parameter in MR Configuration Parameter Page 0 (NVDATA) to enable/disable mix of Enterprise & Opal SED drives.(SCGCQ01596518)
- Make new copy of NVRAM for use with Aero..(SCGCQ01526096)
- Adding ALADIN section to NVRAM struct..(SCGCQ01567124)
- Added field MR_LD_RAID.flags.isEPD.(SCGCQ01581732)
- nvram changes for Snapdump.(SCGCQ01595634)
- Add back section for ALADIN to NVRAM struct.()SCGCQ01605166
- NVDATA parameter to OPAL SED.(SCGCQ01614695)
- Add supportEPDWithAutoConfigOff bit in NVRAM Auto config parameters.(SCGCQ01739489)
- Exposing Write cache as disabled to host for a performance improvement.(SCGCQ01845298)
- PVT API changes needed to support eHBA product series.(SCGCQ01727349)
- PVT_API changes to support Manufacturing SAS PHY test.(SCGCQ01587381)
- Add Aero EEPROM tag.(SCGCQ01574988)
- Preboot OCR- NVRAM changes to limit the number of reset retries to 1 per boot cycle.(SCGCQ01620774)
- Reduce bootup time by 15-20 seconds.(SCGCQ01735563)
- Do ONFI init only for the valid channels and banks.(SCGCQ01760560)
- Add a new bit for Driver/FW communication in the RAID map.(SCGCQ01713674)
- Add DismStartDelayInSeconds in NVDATA.(SCGCQ01758168)
- The SUT can’t boot to OS after 159 loops AC cycle and check the Raid 930-16i 8G.(SCGCQ01788479)


Version 50.5.0-1615 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:  7.05.02.0
	UEFI Driver: 0x07050401
	HII:   07.05.06.03
	MR FW: 5.050.00-1616
    package 50.5.0-1615

Defect fixes.
SCGCQ01487406-Set ldRestriction appropriately in MFCD parameters and persistent config pages  ( This is the controller property update defect)
 
SCGCQ01845298- Exposing Write cache as disabled to host for a performance improvement ( Performance Defect)
 
Note : 
1.This 18B build doesn't have the  HII sorting issue fix  backported - Reason being HII and EFI driver is yet to be signed for 18D( this has the fix), However shared  18B package has signed EFI driver and HII ( w/o HII sort fix)

Version 50.5.0-1510 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:  7.05.02.2
	UEFI Driver: 0x07050403
	HII:   07.05.06.05
	MR FW: 5.050.00-1526
	package 50.5.0-1510

- (IOP-Only.(SCGCQ00138036 ) 
 - Write Cache enable to be done after we are done with all in memory things(SCGCQ00138178) 
 - Thunderbolt hangs at diag reset but works fine at reboot	(SCGCQ00140379) 
 - Fix unused variable(SCGCQ00140591) 
 - Change hardcoded fault code to a properly defined code.(SCGCQ00141606) 
 - Degraded Physical Disk coming as optimal when a diag reset is issued on a pending resync raid10 volume in Linux(SCGCQ00141891) 
 - x5891 Fault After OPEN Timeout(SCGCQ00145434) 
 - FPGA: Gen3 TaskMgmt: 0x265D Fault When Processing Multiple TARGET RESET TMs(SCGCQ00145645) 
 - Correction to Diagnostic Code to Show PL Memory Details(SCGCQ00145990) 
 - FPGA: Gen3 TaskMgmt: 0x5110 Fault on Overlapped TARGET RESETs to SATA devices(SCGCQ00146626) 
 - Fault 265D occurs when running IOs to volume which has 1 drive connected via cable breaker & 1 direct attached,to HBA.(SCGCQ00147098) 
 - FPGA: Timers executing too quickly(SCGCQ00147270) 
 - Fast Path started, Firmware completed IO not working. Host sees 0x00 value in reply descriptor SMID(SCGCQ00148012) 
 - Kantana RAID accelerator base effective address conflicts with cached context memory address	(SCGCQ00149244) 
 - Update rmtflash Perl script debugger breakpoint address(SCGCQ00155189) 
 - Constant/register form of MoveToDCR assembly language macro incorrect( SCGCQ00155799 ) 
 - Fault 0x0612 when performing a Message Unit Reset( SCGCQ00156372 ) 
 - FPGA: FPGA stops repsonding after Diag reset	( SCGCQ00158578 ) 
 - MPI firmware download command never completes( SCGCQ00160359 ) 
 - After downloading FW with SAS FLASH, controller hangs( SCGCQ00162026 ) 
 - Fault 265D occurs when an Inquiry for VPD Page 0x80 is issued to an IR Volume(SCGCQ00163833 ) 
 - FPE fault D094( SCGCQ00167842 ) 
 - Changes to preamble finder and gate training algorithms( SCGCQ00168441 ) 
 - Fpe exception queue interrupt handling does not update queue if an entry is invalid( SCGCQ00168593 ) 
 - PL is faulting with fault code 0xd075 when an IO times out( SCGCQ00170147 ) 
 - Problems running Cobra DDR3 library on Palladium	( SCGCQ00173068 ) 
 - Fault D091 with Destructive Domain Validation Test.( SCGCQ00173093 ) 
 - ReadBuf Command hangs( SCGCQ00174555 ) 
 - Host boot will fails	( SCGCQ00175662 ) 
 - FPGA: IOs fail during Target Mode SSP TM tests( SCGCQ00177626 ) 
 - D110 fault while doing Block Move test( SCGCQ00181603 ) 
 - Fault 670A with Block Move Test and Powercycling Enclosures( SCGCQ00181751 ) 
 - Internal Customer has integration issues with trial release of DDR3 library( SCGCQ00182818 ) 
 - MPI2: IO Unit Page 10 structure incorrect( SCGCQ00183867 ) 
 - SBR byte names don't match Invader EDS or address macros	( SCGCQ00184890 ) 
 - Phy power code is using the wrong mask( SCGCQ00186364 ) 
 - Changed data type returned by getDataScrubDuration(( SCGCQ00187141 ) 
 - Occasionally RMTFLASH can be difficult to make work correctly( SCGCQ00187266 ) 
 - Create workaround for [invader]932( SCGCQ00187388 ) 
 - Fault 0x2663 while running Task Management and IOs( SCGCQ00187408 ) 
 - TBM Recursive Fault( SCGCQ00187763 ) 
 - Controller faults with code 6003 while running task management tests	( SCGCQ00187962 ) 
 - Host booting firmware does not load firmware	( SCGCQ00188336 ) 
 - Core reset causes high latency in Ethernet( SCGCQ00188834 ) 
 - FPGA build would hang on boot/startup( SCGCQ00188929 ) 
 - Fixes to enable Ethernet in mainline builds	( SCGCQ00189763 ) 
 - Modified ring and trace buffer dump to display the data when called from an active console( SCGCQ00189799 ) 
 - Bad output from CLI command iop show mreq( SCGCQ00190178 ) 
 - Gen3: A Jammer script sends too much data for a Read command which results in SysDmaParity fault.( SCGCQ00190412 ) 
 - Fault 0x1901 when firmware errors out IOs with Invalid Descriptor( SCGCQ00190906 ) 
 - Gen3 PwrMgmt: Update shared global Pwr Mgmt structures.( SCGCQ00192501 ) 
 - Misplaced pre-processor directive in pbam.h causes big endian compiles to fail( SCGCQ00192631 ) 
 - Syntax error in pbam.h - missing semicolon in structure definition( SCGCQ00192913 ) 
 - 2nd set of changes to DDR3 library from lab validation( SCGCQ00193153 ) 
 - The fast path status of drives used for volume spares or hot replacement retain Fast Path state of Enabled.( SCGCQ00193388 ) 
 - Firmware repeatedly sending a event whenever it get a spinup notify causes target mode initialization to stall( SCGCQ00194444 ) 
 - FPE Status values passed to iopiFPEHandleException( SCGCQ00194558 ) 
 - Ethernet: Ethernet Page 0 addresses reported in the wrong endian	( SCGCQ00194888 ) 
 - Gen3 PwrMgmt: Unexpected event is sent when changing Direct Attached HDD Pwr states.	( SCGCQ00194919 ) 
 - IO Timeouts/0x6001 fault during SATA TM Read Mayhem test	( SCGCQ00195557 ) 
 - Fault 0x060F when sending very heavy IO load	( SCGCQ00198466 ) 
 - BIST firmware not accurately performing or reporting BIST status	( SCGCQ00200151 ) 
 - Invader A0: D072 Fault during stress and whole port glitches	( SCGCQ00200261 ) 
 - Invader A0: 5893 Fault when the whole port (between enclosures( SCGCQ00200645 ) 
 - Fault 0x0A03 or 0x1609 seen under various circumstances( SCGCQ00202530 ) 
 - UART doesn't display authentication prompt when expected	( SCGCQ00202951 ) 
 - Unable to DMA the debug string token	( SCGCQ00203007 ) 
 - IO timeout to SATA target behind expander.( SCGCQ00203063 ) 
 - Invader A0 - Script 'ctrlSysLogSrv.pl' doesnt prints firmware logs when a hostname with fully qualified domain name is given for 'clientName' argument( SCGCQ00203291 ) 
 - Gen3: PM - Global Power Management TAKE/RELEASE CONTROL requests never complete.	( SCGCQ00203509 ) 
 - Resync happens when RAID1E vol(After clean shutdown( SCGCQ00206367 ) 
 - The DefaultMetadataSize field in IocPage6 is now populated with the number of MBs and not the number of sectors.( SCGCQ00206785 ) 
 - Invader A0: IOUnit Page 7 showing a PCIeSpeed of 2.5G when running at 8.0G.( SCGCQ00207545 ) 
 - Gen3: PwrMgmt initialization may cause a 265D fault at start of day.	( SCGCQ00207646 ) 
 - Invader A0 : Incorrect data from Log Page 0 on second read.	( SCGCQ00207682 ) 
 - The fast path state for newly discovered SATA drives was being set incorrectly.( SCGCQ00209162 ) 
 - FPGA-only: Zero initialized TCM data area not getting cleared( SCGCQ00209959 ) 
 - .10 firmware faults on boot with a 0x0012 fault code	( SCGCQ00209969 ) 
 - Invader A0: All devices go missing when the link between the first two expanders is broken( SCGCQ00210025 ) 
 - 8-port Fury controller has incorrect PCI Device Id( SCGCQ00210028 ) 
 - Fault 9019, during DDR3 initialization, with dual rank support enabled.( SCGCQ00210290 ) 
 - DDR3 Library fault 0x9019 observed when ECC enabled on 32bit width memory( SCGCQ00210687 ) 
 - DDR3 Library Faultcode 0x9019 observed on some boards( SCGCQ00215958 ) 
 - PPC476 L2 store re-ordering with address match collision can cause data corruption( SCGCQ00218038 ) 
 - Failures connecting to SATA drives or expander attached disks( SCGCQ00218117 ) 
 - Intermittent Read Leveling Failure( SCGCQ00221265 ) 
 -( SCGCQ00221570 ) 
 - Invader A0 (USB( SCGCQ00222099 ) 
 - Invader A0: Controller hangs when releasing snapshot buffer( SCGCQ00222775 ) 
 - Fault 0x265D seen when performing Message Unit Reset with posted diagnostic buffer.( SCGCQ00222847 ) 
 - Invader A0: 0x1808 fault when flashing firmware with DDR enabled	( SCGCQ00223684 ) 
 - Fault 5845 seen when running IO with cable glitching	( SCGCQ00224215 ) 
 - Invader A0: 0x2622 Fault seen during initialization in Romley (PCIE3.0 system( SCGCQ00224800 ) 
 - Firmware displayed wrong version number( SCGCQ00225971 ) 
 - Invader A0 IR firmware fault with the error code 8316( SCGCQ00227202 ) 
 - Invader B0: Local Chain hardware incorrectly configured( SCGCQ00227842 ) 
 - Invader A0: Fault x5842 with running Block Move and Task Management Test (SCGCQ00227896 ) 
 - Fault x5900 seen running heavy IO with discovery	( SCGCQ00228216 ) 
 - Changed MfgPage10 bit IOC_MFG10_GF0_CONSISTENCY_CHECKING_DISABLED definition.( SCGCQ00228747 ) 
 - Read leveling error interrupt is observed after DDR initialization( SCGCQ00228826 ) 
 - R10/R1E volume Resync is not happening after activating a foreign volume with UNCLEAN shutdown (w/_CC_DISABLED	( SCGCQ00229652 ) 
 - Fault 0x5842 occurs when cable break/glitching done running IO( SCGCQ00232016 ) 
 - Machine Check Interrupts prevent firmware from loading( SCGCQ00237604 ) 
 - SAS3: 0x265D Fault while disabling Fast Path.( SCGCQ00238050 ) 
 - Romley system hangs during POST with two Invader HBAs installed( SCGCQ00238686 ) 
 - DIS(Data Integrity Signature	( SCGCQ00239359 ) 
 - IO timeouts while running stress loads on a mix of SAS and SATA drives( SCGCQ00239369 ) 
 - Restored memcfg.c( SCGCQ00239519 ) 
 - CSET 235613 includes unexpected changes( SCGCQ00242171 ) 
 - Large IO size to mixed SAS/SATA causing errors( SCGCQ00242618 ) 
 - PL Fault 0x670C( SCGCQ00243099 ) 
 - ONFI: Remove unrelated defines( SCGCQ00245410 ) 
 - Failing a drive in RAID1 volume having write caching enabled resulted in dereference of a NULL pointer.( SCGCQ00245750 ) 
 - DDR3 Training fails at 1866 MTS due to preamble not found on some lanes( SCGCQ00245842 ) 
 - MSIX Table Size field in Config Space doesn't match supported value( SCGCQ00247483 ) 
 - ONFI: Bug in the onfiiFlashContReset function( SCGCQ00247604 ) 
 - Discovery error x90 while running IOs on a mix of SAS and SATA drives.( SCGCQ00249597 ) 
 - ONFI: DMA state of the controller not updated properly( SCGCQ00250932 ) 
 - ONFI: Update the diag command to reflect the change in ONFI interface function( SCGCQ00252023 ) 
 - Moved files that called MoveFromDCR back to IopCommon.h	( SCGCQ00257836 ) 
 - Fault 0x58B4 when trying to run on a 4port controller( SCGCQ00258518 ) 
 - NVData Schema: Update schema for 4-phy devices to contain the correct number of phys	( SCGCQ00258713 ) 
 - NVData: Incorrect NVData image used in A0 parts	( SCGCQ00259169 ) 
 - Code analysis tool defects resolution	( SCGCQ00263862 ) 
 - (IOP	( SCGCQ00270313 ) 
 - DDR3 library fails to train second rank of dual rank memory successfully( SCGCQ00271260 ) 
 - IOP Interrupt causes 0x0D03 fault in B0 chips( SCGCQ00277833 ) 
 - IOP Ethernet Phy driver sends link down event when the link is not down( SCGCQ00279273 ) 
 - Invader B0: 6003 fault while running SSP_INIT_Normal_List group of jammer scripts( SCGCQ00280742 ) 
 - PI Errors on Remove and Insert of Volume Member( SCGCQ00282383 ) 
 - Print function may access an out-of-bound array element( SCGCQ00282902 ) 
 - Training fails on second rank, with certain memory and speeds( SCGCQ00284177 ) 
 - ONFI flash controller interrupts should not be communicated to MPIC( SCGCQ00284520 ) 
 - Fixed source level debugging using GHS probe.( SCGCQ00286179 ) 
 - Fault d075 - Frameownership issue for FP IO which is already failed with exception.( SCGCQ00286703 ) 
 - Invader B0: FPE Manager Fault code cleanup and documenation update( SCGCQ00286906 ) 
 - 0x26B1 fault when BIOS initializes firmware( SCGCQ00287155 ) 
 - Fast Path hardware Auto Pend and Completion events don't work.( SCGCQ00287160 ) 
 - Cannot change CPU speed from 50% to 1005 using the serial port diagnostic command.( SCGCQ00291334 ) 
 - Fault x5801 seen running IO with Task management	( SCGCQ00292512 ) 
 - Volume removal resets the controller for further operations.	( SCGCQ00292814 ) 
 - Invader faults with 0x7C39 when sending Security Protocol Out Disable Password command( SCGCQ00293371 ) 
 - IOP: Fault 0x2625 while accessing PCI registers( SCGCQ00294460 ) 
 - L2 Parity error occurs when dumping SAScore registers via UART command( SCGCQ00296461 ) 
 - Address in the descriptor is physical and cannot be used directly as virtual address	( SCGCQ00296758 ) 
 - ONFI: Creating Bad Block list returns failure status on B0( SCGCQ00297974 ) 
 - Invader B0: SATL:'Additional Sense' not set for REQUEST SENSE command when the drive is moved to IDLE power condition state( SCGCQ00300293 ) 
 - Invader NVData MfgPg16 contains duplicate element names( SCGCQ00304780 ) 
 - DDR3 library: Change PHY ODS and slew rate settings for clock( SCGCQ00304789 ) 
 - Invader B0: 0x0612 fault while powering down SLES11.2 system	( SCGCQ00304856 ) 
 - ONFI B0: BadBlockList creation takes several minutes for Bank1( SCGCQ00316044 ) 
 - (FPGA( SCGCQ00316360 ) 
 - Foreign volume activation fails in the presence of failed native volume( SCGCQ00319367 ) 
 - ONFI: Flash Clock Divider not set properly( SCGCQ00321327 ) 
 - Reserved field of IOCFacts Reply is set to non-zero value( SCGCQ00322950 ) 
 - Invader B0: Fault 583A during Destructive Domain test( SCGCQ00323745 ) 
 - Configuration pages of type Ext Manufacturing are not available in CLI( SCGCQ00324561 ) 
 - CCR Version Changes to Enable Support for Invader C0 Chip Revision.( SCGCQ00326701 ) 
 - NVDATA Change to Allow Support for Invader C0 Chip Revision	( SCGCQ00326818 ) 
 - Low performance seen doing very low Q depths (1,2,3 outstanding IO levels( SCGCQ00328670 ) 
 - Turned S/W chain pull back on.( SCGCQ00332189 ) 
 - (NVDATA( SCGCQ00334156 ) 
 - Supress the miniDMA debug prints by default.( SCGCQ00334572 ) 
 - DIAG_SHOW_MREQ_DETAIL feature fails to compile( SCGCQ00350762 ) 
 - (IOA	( SCGCQ00353301 ) 
 - Back end PCI bring up( SCGCQ00353319 ) 
 - Backend PCIe doesn't handle Legacy interrupts( SCGCQ00361845 ) 
 - Initial NVMe bringup fixes( SCGCQ00363615 ) 
 - When running RBD, Python interpreter is not found( SCGCQ00364511 ) 
 - New flag to force the DQS sampling window further than what was calculated( SCGCQ00368461 ) 
 - StartFPGA GUI doesn't gracefully die when network connection is not available( SCGCQ00376571 ) 
 - Some PCIe config page fixes( SCGCQ00392850 ) 
 - Clean up task for Dauntless #defines when building PL / CFGI library...( SCGCQ00398327 ) 
 - Update the usblib/sas3hw.h file to the latest( SCGCQ00399265 ) 
 - Fixes for non read/write SCSI IO requests to a backend NVMe device( SCGCQ00399268 ) 
 - Critical Fixes for PCIe IO Unit config pages	( SCGCQ00400007 ) 
 - Unaligned CE Image causes PL fault 0xd115 when using CE Auto Load( SCGCQ00408789 ) 
 - Backend NVMe devices don't work if stored host page size is invalid( SCGCQ00410848 ) 
 - (BUILD( SCGCQ00413626 ) 
 - Handle Stang BAD_ALIGNMENT exception differently	( SCGCQ00414488 ) 
 - Modify handling of a couple of Stang exceptions	( SCGCQ00415459 ) 
 - NVMe: Data corruption and unexpected IO failures	( SCGCQ00418954 ) 
 - MaxPayload/MaxReadRequestSize are getting set to strange values in some cases( SCGCQ00420926 ) 
 - Build without PL_FEATURE_PCI_DEVICE_SUPPORT fails to compil( SCGCQ00434704 ) 
 - SAS3.5: Add ALADIN feature macro and add pliAladin function calls to pliComplianceCheck.c.( SCGCQ00436117 ) 
 - Dauntless F/W not setting PCIe protocol support in ProtocolFlags in IOCFacts	( SCGCQ00436936 ) 
 - AHCI: read timeout after issuing MODE SENSE command( SCGCQ00441381 ) 
 - The TBM is initialized twice in Invader (and Dauntless( SCGCQ00443385 ) 
 - AHCI: PL shouldn't fault when AHCI SGL translation encounters an invalid address	( SCGCQ00443456 ) 
 - NVMe: PL shouldn't fault when NVMe SGL translation encounters an invalid address	( SCGCQ00448246 ) 
 - Data Corruption observed during IO + "random" TM to AHCI	( SCGCQ00457786 ) 
 - PL: Firmware path read/write IOs to backend PCIe devices may time out( SCGCQ00481302 ) 
 - NVMe Encapsulated Path Fixes	( SCGCQ00493331 ) 
 - NVMe: IO timeouts or fault after several command failures( SCGCQ00495200 ) 
 - IO's Fail to SAS/SATA Drives	( SCGCQ00504669 ) 
 - NVMe: 60D fault on encapsulated request failure( SCGCQ00504708 ) 
 - SAS3.5FW: PL: PCI: Use PliRegister for device registration instead of hardcoded value( SCGCQ00558177 ) 
 - Build errors - Fix many lint-related bugs introduced last week.( SCGCQ00568553 ) 
 - NVMe: Fix several mode page related bugs	( SCGCQ00570058 ) 
 - DAUNTLESS: Update several items in SPI Flash for Dauntless( SCGCQ00593519 ) 
 - Firmware boot failure occurred because of some IOP workarounds and flash layout not being updated in scripts that are used to erase and program flash memory.( SCGCQ00599967 ) 
 - Dauntless: Fault 265D MPI IO Unit Control Message - CLEAR PERSISTENT	( SCGCQ00604486 ) 
 - Some of the declarations and typedefs in pliDefs.h not conforming to code standard( SCGCQ00606222 ) 
 - Incorrectly named PLI_RUNTIME_CONFIG flag definitions( SCGCQ00606259 ) 
 - Delay timers are not used properly for some FPGA applications( SCGCQ00610868 ) 
 - Few minor backend PCIe related changes( SCGCQ00613904 ) 
 - Bug Fixes in NVMe Encapsulated IO Path( SCGCQ00621303 ) 
 - NVMe: IEEE to PRP translator rollback issues	( SCGCQ00626787 ) 
 - Inappropriate setting of PCIe and Man Page 12, 13 parameters for Intruder in xsd file( SCGCQ00649433 ) 
 - SAS 3.5 FW: 0x265d fault during bootup with tip code	( SCGCQ00654908 ) 
 - Intruder: REMAPPED_SASCORE1 is a IOP-only define	( SCGCQ00663251 ) 
 - Change NVDATA to not limit Intruder Man Pages to just 2 phys	( SCGCQ00670987 ) 
 - Intruder: Fix unprotected loop in plTargetProcessHardReset(	( SCGCQ00678870 ) 
 - CLI command "iop show cfg PHY 4" only returns data for PHY 0	( SCGCQ00682913 ) 
 - Ventura: arm_all build might fail with error	( SCGCQ00685835 ) 
 - VENTURA: Fix various issues in SPI library( SCGCQ00686523 ) 
 - Ventura: Firmware aborts during SOD intialization( SCGCQ00688139 ) 
 - Ventura: Phy13 repeated twice in ManPage5( SCGCQ00688188 ) 
 - Ventura: vector mismatch errors when validating sectors.	( SCGCQ00694613 ) 
 - VENTURA: SPI Flash init does not return failure if SRAM buffer size is not specified	( SCGCQ00698193 ) 
 - Firmware faults when downstream port of attached PCIe switch sends uncorrectable fatal error for malformed TLP it received from connected device.( SCGCQ00699010 ) 
 - Ventura: Processor abort when initializing Txdma buffer( SCGCQ00700796 ) 
 - Backend PCIe: AHCI spinup may fail( SCGCQ00702640 ) 
 - VENTURA: SPI DCR End address is not set for CS2, CS3, CS4( SCGCQ00705378 ) 
 - Faulting Firmware only sends SAS Trace trigger out on Core 0 phys( SCGCQ00712956 ) 
 - VENTURA: SPI Flash HW workaround for SPI writes( SCGCQ00713020 ) 
 - Incorrect assignment of PBAM SGPIO Instance Size macro( SCGCQ00715174 ) 
 - Ventura: Lower bits of physical address are lost when converting virtual to physical addresses( SCGCQ00715570 ) 
 - VENTURA: cfgi lib appears to use more memory than requested/allocated( SCGCQ00716821 ) 
 - Intruder: remap SAS Core addresses earlier in the start-of-day routine( SCGCQ00722594 ) 
 - Intruder FPGA (IOP FW( SCGCQ00725988 ) 
 - NVMe: devices always fail to initialize( SCGCQ00729685 ) 
 - Ventura: Incorrect Case in Function Parameter( SCGCQ00734961 ) 
 - Intruder FPGA: Fault 0x060f while running Heavy Read IO Stress Test( SCGCQ00735932 ) 
 - Dauntless: tip code appears to be broken	( SCGCQ00737126 ) 
 - Fault 0x6001 While running Task Abort to topology of only SATA Drives during I/O.( SCGCQ00740832 ) 
 - Ventura: Too many device handles are being allocated	( SCGCQ00747380 ) 
 - Ventura: Bad merge backed out the fix in SCGCQ00716821( SCGCQ00748108 ) 
 - Ventura: Internal SCSI W/R tests fails to allocate memory( SCGCQ00751433 ) 
 - Intruder FPGA: Fault 0xD062 while running Block Move and Task Management test to SATA Only( SCGCQ00759067 ) 
 - Ventura: System abort in bootloade( SCGCQ00759376 ) 
 - Ventura: Linking Remote Flash Fails( SCGCQ00759589 ) 
 - Ventura: ARM Make Clean sometimes fails	( SCGCQ00762890 ) 
 - Fault xD117 seen when running IO with Task Management Abort Task and Abort Task Set TMs being issued	( SCGCQ00762899 ) 
 - IOP: PowerPC ITLB Miss Errata, additional linker changes	( SCGCQ00765342 ) 
 - pliProtos.h contains 2 internal protos for sim/fake IO( SCGCQ00769245 ) 
 - Fix build clean syntax( SCGCQ00769432 ) 
 - CFGI library linking errors with gcc	( SCGCQ00771070 ) 
 - pl: backend PCIe: couple of PCIe IO Unit Page 1 issues( SCGCQ00776230 ) 
 - NVMe: EF08 fault during non target reset task management	( SCGCQ00776392 ) 
 - Intruder FPGA: Fault 0xC00C while running Initiator and Target Mode on Intruder Cores( SCGCQ00776417 ) 
 - Ventura: Write to NVSRAM does not function properly( SCGCQ00776859 ) 
 - Ventura: after boot SAS drives take minutes to complete discovery( SCGCQ00780785 ) 
 - Ventura: Build utilities won't compile( SCGCQ00790266 ) 
 - Intruder FPGA: 0xD20C Fault While Running Stress From 4 Initiator System to Target Mode FPGA	( SCGCQ00791373 ) 
 - Ventura: PCIe Discovery problems observed with device reset test.( SCGCQ00793909 ) 
 - NVMe: D300 fault on malformed chain to PRP list SGL( SCGCQ00794103 ) 
 - Dauntless: tip code is broken( SCGCQ00798119 ) 
 - pl: backend PCIe: special case cascaded switch issues( SCGCQ00799848 ) 
 - Intruder FPGA: Add interrupt handler back in for IOP Completion Queue notempty for Ventura builds( SCGCQ00807447 ) 
 - SAS3.5 Build for rmtflash_fpga is failing( SCGCQ00810267 ) 
 - SAS3.5 rmtflash_fpga does not build( SCGCQ00811369 ) 
 - Default NVDATA Values for Ext Mfg Pages 42/43 Are Incorrect( SCGCQ00813906 ) 
 - Dauntless FPGA: Data Corruption reported on multiple tests( SCGCQ00813954 ) 
 - Manufacturing Page 2 Word Size is Incorrect( SCGCQ00821488 ) 
 - Ventura: Sascore 1 links do not come up( SCGCQ00822145 ) 
 - Ventura: "iop arm table" crashes due to missing string( SCGCQ00829296 ) 
 - Intruder Bring up( SCGCQ00832698 ) 
 - IOP: SASCore base addresses don't need to be sequential.( SCGCQ00833117 ) 
 - BL: Intruder A0 faults with code 0x2622( SCGCQ00833775 ) 
 - Ventura: Add Parity and SysDMA work-arounds for initial Maverick core( SCGCQ00835360 ) 
 - IOP: Fault 0x0701 seen on first boot of firmware flashed to blank Intruder A0 board( SCGCQ00835379 ) 
 - IOP: Intruder firmware faults 0x2622 on A0 during a cold boot from flash	( SCGCQ00835435 ) 
 - IT Release Build Script Not Copying All the Correct Files( SCGCQ00836314 ) 
 - IOP: Firmware download request can cause firmware to become unresponsive	( SCGCQ00836356 ) 
 - Fixed IT Signed Firmware Build	( SCGCQ00836362 ) 
 - Ventura: backend PCIe: host bringup fixes, part 1( SCGCQ00837192 ) 
 - Ventura: Fix Utility Compilation Issues - Round 1( SCGCQ00837242 ) 
 - Fix comiplation of some utilities in controllerfw/bld.( SCGCQ00837270 ) 
 - Intruder: NVData had the incorrect PCI Vendor ID in General Data area( SCGCQ00840317 ) 
 - Ventura: SAS_R31_HACK doesn't always compile correctly( SCGCQ00841016 ) 
 - IOP: Flash writes may cause firmware to fault with code 0x0701( SCGCQ00842428 ) 
 - Fixed Build Release Scripts to Copy Correct NVDATA Files	( SCGCQ00842477 ) 
 - Ventura IOP compile and run-time issues when enabling MSS library.( SCGCQ00843974 ) 
 - Intruder A0: Fault 0x5872 during I/T Switching( SCGCQ00844812 ) 
 - Ventura: core level interrupt starvation	( SCGCQ00844856 ) 
 - Ventura: backend PCIe: fix some scattered bugs( SCGCQ00845780 ) 
 - Ventura: Add fixes for PCI IRQ and DM Register Bugs( SCGCQ00848174 ) 
 - Instance of IOP directly accessing PL to fault the controller( SCGCQ00849745 ) 
 - Cleanup IOP Access to gplPtrPdbRegs( SCGCQ00849748 ) 
 - IOP firmware accesses PL firmware directly without going through PLI	( SCGCQ00849749 ) 
 - Ventura: Fault 0xD06 (Spurious interrupt	( SCGCQ00849760 ) 
 - IOP: Vector Mismatch reported after full erase and flash of firmware and SAS Address	( SCGCQ00850743 ) 
 - Ventura: backend PCIe: core level interrupt starvation( SCGCQ00851229 ) 
 - IOP: Flash memory does not have read side effect attribute set( SCGCQ00852087 ) 
 - IOP: iopiDiagCmdReadMem( SCGCQ00852274 ) 
 - Ventura: Workaround for iopiDiagCmdReadMem( SCGCQ00852920 ) 
 - Intruder A0: 265D fault observed during link reset task management with IO( SCGCQ00853930 ) 
 - NVDATA: Fix field offsets to Manufacturing Page 12 XML( SCGCQ00855011 ) 
 - Ventura: need to use ARM_IRQ_PRIORITY_POLL for polled interrupts	( SCGCQ00856520 ) 
 - Ventura FPGA: need workaround for host side SysDma in 3.0 bitstreams	( SCGCQ00856692 ) 
 - Ventrura: Accessing Mode Sense pages for NVME Results in alignment fault	( SCGCQ00857247 ) 
 - Ventura FPGA: Old config valid RAM flags set in flash limits memory available for use( SCGCQ00860688 ) 
 - Ventura FPGA: Faults observed when powering off/on populated PCIe switch	( SCGCQ00861780 ) 
 - Ventura: NVMe: PL translated non read write commands may time out( SCGCQ00862206 ) 
 - View and Modify the iop dbgmask ir through Intruder CLI( SCGCQ00864796 ) 
 - Ventura: When processing SAS core interrupts, sometimes status register indicates no active interrupts( SCGCQ00866361 ) 
 - Ventura: backend PCIe: backend completion timeouts occur when the FPGA is heavily loaded	( SCGCQ00866758 ) 
 - Change the naming of library defines DEBUG and TARGET to avoid conflicts with customers	( SCGCQ00866760 ) 
 - ComboSerdes library builds for Ventura do not complete succesfully( SCGCQ00867359 ) 
 - Bug in strtoul( SCGCQ00867905 ) 
 - Intruder A0: Manufacturing Page 9 configurations for number of Virtual functions set to 1 for Non-SRIOV firmware	( SCGCQ00868952 ) 
 - Able to see informaton on Integrated RAID information in Manufacturing Pages 4 and 10( SCGCQ00869324 ) 
 - Ventura: Structures not being put in IOA Local RAM( SCGCQ00869574 ) 
 - IOP: I2C uninitialized variables and GPIO switch break( SCGCQ00870602 ) 
 - IOP: Removed dead code from CLI read memory function	( SCGCQ00870625 ) 
 - Ventura: backend PCIe: target reset to AHCI device times out	( SCGCQ00871680 ) 
 - PL: Fix bad coding style in plGetSpinupGroup	( SCGCQ00871683 ) 
 - Ventura: backend PCIe: fix 'iop scsi big' debug command( SCGCQ00872109 ) 
 - PL: Firmware does not fill in SAS IO Unit Page 16 Timestamp field correctly( SCGCQ00872141 ) 
 - IOCfacts Reply Error for Ventura regarding SOP Protocol( SCGCQ00872258 ) 
 - Bug in strtoul( SCGCQ00873987 ) 
 - Ventura: ARM build failures do not cause "bld33xxgnu all" to fail( SCGCQ00873994 ) 
 - Gen 3.5: Cleanup IOP access to PL( SCGCQ00873995 ) 
 - NO_FPE_HW compile option updates	( SCGCQ00879534 ) 
 - Ventura: backend PCIe: issues related to Axi2Shell error handling( SCGCQ00880773 ) 
 - Incorrect PCIe Readings in UART with Intruder( SCGCQ00880938 ) 
 - Fix two separate 0x265D faults( SCGCQ00881295 ) 
 - Transition from MPI SAS IO Unit Control request to IO Unit Control request coding incomplete( SCGCQ00883285 ) 
 - SAS/SATA power management was enabled by mistake	( SCGCQ00884080 ) 
 - Intruder: Build error after merging firmware files( SCGCQ00884551 ) 
 - Ventura: RMC code does not build	( SCGCQ00885675 ) 
 - PL faults on PNPR Error Syndrome interrupt that is hit during link glitch test( SCGCQ00885805 ) 
 - IOP: UART outputs 18 instances of Manufacturing Page 9( SCGCQ00888269 ) 
 - TigerStryker: Liger PL Library build needs to allow debug symbols to be built( SCGCQ00890807 ) 
 - SASSDCHANLANEADDR Macro formula is incorrect	( SCGCQ00894128 ) 
 - Tiger/Stryker: Fix tiger firmware build and build all issues	( SCGCQ00894132 ) 
 - Tiger/Ventura: change FXCore init delay to coding standard format( SCGCQ00894651 ) 
 - Ventura: interrupt handler latency in CPU not sleeping case( SCGCQ00897157 ) 
 - Tiger/Stryker: Fix compiler error with tigerfpga build( SCGCQ00897468 ) 
 - Ventura: backend PCIe: need to update master XSD file for SCGCQ00865951( SCGCQ00902961 ) 
 - Ventura: MemRd Requests that have TH bit (TPH Requestor Capability( SCGCQ00906745 ) 
 - PL: Update internal files to latest specifications( SCGCQ00913173 ) 
 - NVDATA: Fix tests against chip revision( SCGCQ00914503 ) 
 - Modify the code to use polling instead of interrupts( SCGCQ00915173 ) 
 - Ventura: backend PCIe: reformulate switch WWID( SCGCQ00915987 ) 
 - Ventura: Build fixes to make Tiger build all work( SCGCQ00916056 ) 
 - IOP: IO Unit Page 7 is not returning a valid PCIe width( SCGCQ00917309 ) 
 - IOP: CLI commands iop show tlb or iop show mem cause 0x265D fault( SCGCQ00917602 ) 
 - Ventura: Uart CLI history option not working	( SCGCQ00919245 ) 
 - Not able to link SASFW_Ventura_Phase_0.6 00.250.49.00 Pl library	( SCGCQ00921951 ) 
 - VENTURA: SPI write/read/erase perform over/under run in corner cases	( SCGCQ00923741 ) 
 - Remove the dependency from the HW definitions in sasctrlfw/common/if/pl/pliDefs.h( SCGCQ00925701 ) 
 - Soft reset the Guinness CSW PUB block on initialization( SCGCQ00926428 ) 
 - Tiger: include CSW lib in Tiger builds( SCGCQ00928508 ) 
 - TigerStryker: Fix pl library build for liger release	( SCGCQ00930678 ) 
 - Ventura non-debug images have debug( SCGCQ00932961 ) 
 - Ventura: Tip code faults with 0xECA6	( SCGCQ00933078 ) 
 - PL Ventura: MultipP bit not set in Inquiry( SCGCQ00933818 ) 
 - Sbus accesses fail and not all serdes spico processors are started( SCGCQ00936651 ) 
 - IOP: Tiger: Tiger firmware doesn't boot( SCGCQ00936948 ) 
 - IOP: PCI Core resets incorrect hardware( SCGCQ00937441 ) 
 - Ventura: SPI library init twice with different chip selects will override DCR start and stop of first chip select( SCGCQ00937998 ) 
 - Tiger: Fix Priority Interrupt bitfield in Maverick Header file.( SCGCQ00938471 ) 
 - Ventura: Misc initial bring-up work-arounds( SCGCQ00938539 ) 
 - SAS Phys 4-7 in each CSW block do not connect( SCGCQ00940212 ) 
 - CRC errors during firmware upload on ventura	( SCGCQ00940386 ) 
 - Tiger: Critical Interrupts from VIC_1 not returning the correct IRQ number( SCGCQ00942278 ) 
 - Tiger: Inbound MSIx Interrupt not getting cleared correctly( SCGCQ00942413 ) 
 - Ventura: Host PCIe Adapter returns CRS forever after host boot( SCGCQ00943062 ) 
 - AACS Server function imported from AAPL causes a Cub firmware fault( SCGCQ00943276 ) 
 - Ventura: A.0 SPILIB does not erase and read SPI flash in auto mode( SCGCQ00944053 ) 
 - Tiger: FW hang on init( SCGCQ00944113 ) 
 - Tiger: PSB PEX hardware initialization code requires data synchronization barrier( SCGCQ00944153 ) 
 - Ventura: Boot time from SPI is too long for PCIe compliance( SCGCQ00944645 ) 
 - Ventura: Invalid Mid (0xDDDD	( SCGCQ00944646 ) 
 - Tiger: Disable Reply FIFO Coalescing for TIGER FPGA	( SCGCQ00944648 ) 
 - Tiger: Fix compilation issues with Multi MSIx reply feature disabled	( SCGCQ00944729 ) 
 - Dauntless Builds Not Completely Removed.	( SCGCQ00944759 ) 
 - Ventura: usable size of OCM is much smaller than expected( SCGCQ00944934 ) 
 - Host PCIe link doesn't come up after warm reboot in most cases( SCGCQ00947329 ) 
 - VENTURA: SPI library: Need memory sync on SPI flash write operation( SCGCQ00948417 ) 
 - AAPL diag.h file contains an unused structure with floating point members( SCGCQ00949576 ) 
 - Ventura: When firmware is booted from FLASH not all of the writable FLASH is mapped (Fault 0x265D( SCGCQ00949777 ) 
 - PCIe / SAS/SATA switching is not working	( SCGCQ00949800 ) 
 - Tiger: Fault 0x1403 with tip code( SCGCQ00949803 ) 
 - Ventura: Combined MSIX Mode Fails( SCGCQ00950015 ) 
 - Ventura: Data abort when booting harpoon image( SCGCQ00950072 ) 
 - Tiger: Fix build all	( SCGCQ00950161 ) 
 - Ventura: Harpoon successfully boots Ventura image( SCGCQ00950212 ) 
 - Tiger: PCIe discovery and configuration fixes( SCGCQ00950664 ) 
 - Harpoon: Data abort when initializing system	( SCGCQ00950857 ) 
 - VENTURA: firmware download and bootup fault with boot fault 1C if flash was not erased( SCGCQ00951226 ) 
 - Host sees incorrect MSIX value in event reply descriptor	( SCGCQ00952622 ) 
 - RMC firmware fails to handle PCIe Hot Reset and Link Disable/Enable properly which causes system to hang or reboot( SCGCQ00952692 ) 
 - Ventura: Vendor defined PCI messages may cause the adapter to hang during POST( SCGCQ00953758 ) 
 - IOP: Spurious interrupt on Tiger	( SCGCQ00954831 ) 
 - Ventura MSS: A0 DDR bring-up	( SCGCQ00961550 ) 
 - ComboSerdes: AAPL prints warnings about AAPL_CHIP_ID_OVERRIDE upon initialization( SCGCQ00966879 ) 
 - Ventura: A0 - MSI/MSI-X error occurs with PCIe error status of Length Mismatch Error during IO stress( SCGCQ00969312 ) 
 - Ventura: backend PCIe: PL NVMe read/write breakup IOs fail badly	( SCGCQ00983674 ) 
 - Tiger: Silicon build not working with new Tiger CCR header( SCGCQ00987111 ) 
 - Ventura: Actions requiring SysDMA fail when firmware is host booted( SCGCQ00987233 ) 
 - POST fails on some servers with Ventura HBA installed( SCGCQ00989307 ) 
 - Tiger IOP: fix hardcoded device ID( SCGCQ00990350 ) 
 - Ventura: Implement work-around for MSIX Vector Completion Timeout Problem( SCGCQ00990361 ) 
 - Ventura: backend PCIe: hang may occur when a backend PCIe link goes down	( SCGCQ00991209 ) 
 - Ventura: iop show ver displays PLB frequency on Ventura	( SCGCQ00991411 ) 
 - SATA Drives do not link up and SAS/SATA links come up at less than optimal speeds( SCGCQ00991424 ) 
 - IOP updates necessary for DDR4 bringup on Ventura( SCGCQ00991767 ) 
 - Ventura - FW hangs while sending MPI25_TOOLBOX_DIAGNOSTIC_CLI_REQUEST.( SCGCQ00992642 ) 
 - Ventura: Switch to parity initialization work-around and turn on 128 vector support( SCGCQ00992931 ) 
 - Ventura: Fails to initialize with 128 MSIX vectors( SCGCQ00993114 ) 
 - Ventura: Eliminate 12-vector MSIX work-around from code( SCGCQ00993120 ) 
 - Ventura: backend PCIe: ED08 fault occurs with backend PCIe enabled and phys disabled	( SCGCQ00993194 ) 
 - Ventura MSS: Second set of changes for A0 bring up( SCGCQ00993821 ) 
 - Ventura: Invert PBAM GPIO LED data polarity( SCGCQ00993950 ) 
 - Removed unused Ventura library files from Clear Case. Added a new build target, cleanvent, to clear Ventura build objects prior to new build.( SCGCQ00996748 ) 
 - Tiger: Fix POM size( SCGCQ00997088 ) 
 - Ventura A0: Power Management functionality for Partial or Slumber capable SAS or SATA devices not enabled( SCGCQ00997277 ) 
 - The PID_TYPE & PID_PROD fields are not set in the IOC Facts reply message.( SCGCQ00997671 ) 
 - Ventura: recursive fault on fault with backend PCIe support disabled at runtime( SCGCQ00997681 ) 
 - Ventura: Complete firmware download fails with loginfo 0x30010108( SCGCQ00997797 ) 
 - CSW Sequence RAM updated to allow SAS Phy Power Management to work( SCGCQ00997834 ) 
 - Tiger: Invalid Requestor ID is used for PCIe TLPs( SCGCQ00998663 ) 
 - IOP: Remove register definitions that don't actually exist in trident( SCGCQ01001094 ) 
 - Adapter fails to respond to diag reset while faulted	( SCGCQ01001666 ) 
 - Ventura: EC22 fault occurs after a SASCore transmit hardware interrupt( SCGCQ01002020 ) 
 - Ventura/Intruder: SCGCQ00997542 fix to firmware download will fail for non-uniform sectored parts( SCGCQ01002406 ) 
 - Ventura: VPD interrupt repeatedly asserts after PCIe VPD access( SCGCQ01003747 ) 
 - Ventura: Modify configuration of GPIOs shared with Eval Board CPLD	( SCGCQ01004229 ) 
 - Ventura: backend PCIe: fault occurs when link configuration is invalid( SCGCQ01004373 ) 
 - Firmware crashed with PL Fault d073 when running IO on multiple R1 VDs( SCGCQ01004990 ) 
 - Ventura A0: Global Power Management Mode changes not working	( SCGCQ01005088 ) 
 - Tiger: (Veloce( SCGCQ01005095 ) 
 - IOP: Tiger must provide PCI Express Extended Capability Header( SCGCQ01005156 ) 
 - Ventura: SPI Library directly writes to mode registers	( SCGCQ01010624 ) 
 - Ventura: Hardware work-around for Link Capabilities 2 register causes PCE incompabilitiy	( SCGCQ01011070 ) 
 - Ventura: Remove Prevail references( SCGCQ01011088 ) 
 - IB Transfer field changes when Performance Counters are Disabled	( SCGCQ01011954 ) 
 - Tiger FPGA: PCI DID needs to be set to 0xB1 instead of 0xAA for Tiger in config space( SCGCQ01011963 ) 
 - IOP: Reply Queue FIFO is inefficiently divided between MSIx vectors( SCGCQ01014813 ) 
 - Tiger FPGA: Temporarily Fix DevHandle offset in Tiger PCIe FMU register(SCGCQ01014979 ) 
 - Ventura: backend PCIe: couple of issues related to resource configuration( SCGCQ01014981 ) 
 - Ventura PL: Remove deprecated MPI SED Initialization step( SCGCQ01015440 ) 
 - Ventura: Sas/IOA deadlock( SCGCQ01016130 ) 
 - Ventura: backend PCIe: workaround for lane breakage on backend PCIe link down( SCGCQ01017060 ) 
 - Ventura: Ventura and Marlin family parts have 0x0000 for Subsystem ID( SCGCQ01017082 ) 
 - Ventura A0: Performance Counters not working as expected	( SCGCQ01018523 ) 
 - Marlin: backend PCIe: various bringup issues	( SCGCQ01018771 ) 
 - Port Enable fails when 'BoardPowerRequirement' field (Manufacturing Page 11( SCGCQ01019972 ) 
 - Ventura: NVMe: Supported WRITE LONG flags mismatch the current SCSI-NVMe translation spec( SCGCQ01020474 ) 
 - Add memport interrupt handling to the memory controller interrupt handler and make corrections for DDR4 ECC implementation.( SCGCQ01020603 ) 
 - Ventura: Spilib - move declaration before statement( SCGCQ01020718 ) 
 - Ventura: backend PCIe: on disable, need to deconfigure backend PCIe sooner( SCGCQ01021385 ) 
 - Ventura A0: SPILIB: Hang in SpiAPIs( SCGCQ01021422 ) 
 - Tiger: SAS complete mode must use SIL 0 for all completion Q tail pointer writes	( SCGCQ01025327 ) 
 - Ventura PL: Handle secondary path completion interrupt beating completion entry writes( SCGCQ01025621 ) 
 - Ventura A0: Incorrect offset used during GPIO BankB output value initialization( SCGCQ01026167 ) 
 - Ventura: NVMe: SGL translation may fail with unaligned first SGE	( SCGCQ01026995 ) 
 - Ventura: SPI library code fails to write NVram in quad mode for specific NVSRAM part	( SCGCQ01028117 ) 
 - Ventura A0: Performance Counters not working as expected for NVMe drives	( SCGCQ01029636 ) 
 - GHS linker .dba files are missing from the lib folder( SCGCQ01029700 ) 
 - Ventura Tiger: 0x265d Fault while running Task Management Test to tiger attached SATA drive( SCGCQ01032769 ) 
 - Tiger Ventura: Remote MPI device (SED( SCGCQ01032856 ) 
 - Ventura A0: Raw firmware name available under IT folder is different as mentioned in Readme available in nvdata_dat folder.( SCGCQ01033781 ) 
 - Ventura MSS: RDIMM fails to train( SCGCQ01034014 ) 
 - Ventura MSS: Hardware Workaround for DDR refresh during training issue( SCGCQ01034016 ) 
 - Ventura A0: Fault 0x0004 post power cycle after downloading 0.60 firmware( SCGCQ01034069 ) 
 - Ventura A0: Fault 0x0004 post power cycle after downloading 0.60 firmware with Quad Mode	( SCGCQ01035610 ) 
 - Aladin hangs system - wrong clock being selected	( SCGCQ01035864 ) 
 - Ventura: backend PCIe: 61A5 fault on frequent errors involving an NVMe device( SCGCQ01039087 ) 
 - Ventura MSS: ECC improvements for operation at 2133( SCGCQ01039164 ) 
 - Ventura: PL Include Files Result In error ARCH_TYPE not defined( SCGCQ01039167 ) 
 - Fault during Aladin CLI commands.( SCGCQ01040069 ) 
 - Ventura: In SRIOV mode, FLRControl Done Is Not Set when FLR is issued to VF's( SCGCQ01040078 ) 
 - FMU Security is Always Enabled and Can Not Be Turned Off	( SCGCQ01043903 ) 
 - aView EBERT and ESCOPE commands fail via TCP/IP	( SCGCQ01045574 ) 
 - Tiger FPGA: Fault 6230 is seen during IO and TM on direct attached SATA( SCGCQ01045612 ) 
 - Ventura MSS: Update CA parity setup during DDR init	( SCGCQ01046321 ) 
 - Ventura: backend PCIe: EC30 or EC70 fault on direct attached link down( SCGCQ01046534 ) 
 - IOP: Firmware faults with 0x265D when issuing a TM to a device behind a SED which is no longer connected	( SCGCQ01049418 ) 
 - Setting manual trigger of Aladin block causes system lock up.( SCGCQ01050624 ) 
 - Ventura: SPI library - Flash API read missed first 4 bytes in quad mode version	( SCGCQ01051481 ) 
 - Ventura A0: Running all Task Management types to only PCIe devices results in fault 0xECA3( SCGCQ01053437 ) 
 - PL does not map IOP requested resource to backend PCI space with AXI bus attribute and faults( SCGCQ01054900 ) 
 - Host Trace Starting Offset Incorrect if the trace is not released properly( SCGCQ01055030 ) 
 - CPU clock of "iop show ver" command has wrong value.	( SCGCQ01059458 ) 
 - Ventura: 8 LUN Target Using Linux Driver Performs 10% or more slower than previous SAS3 products	( SCGCQ01060022 ) 
 - MPI version noted as 0 during firmware upgrade.	( SCGCQ01060320 ) 
 - Data corruption issues when CA parity enabled.( SCGCQ01061968 ) 
 - Tiger: Improve DPC handling	( SCGCQ01062268 ) 
 - Tiger FPGA: Backup Common Boot Block not loading after reset	( SCGCQ01062712 ) 
 - Ventura: backend PCIe: various faults occur after a short link glitch( SCGCQ01064269 ) 
 - Ventura: Partial NVDATA Chip Comments Wrong for sas3616 and sas3716	( SCGCQ01065944 ) 
 - Using iop xget trace command results in truncated host trace file if the file hasn't been released( SCGCQ01066380 ) 
 - Ventura: Fault 265d during PL initialization - Data abort( SCGCQ01068731 ) 
 - Part Numbers of Some Chips Displayed Incorrectly	( SCGCQ01070188 ) 
 - For NVMe drives mode sense command failed for PAGE CODE=0x3F and SUB PAGE CODE=0xFF	( SCGCQ01070881 ) 
 - Tiger: IOP: The initial setup of the PCI Serial Number is incorrect	( SCGCQ01072983 ) 
 - Marlin MSS: Various MSS updates found during Marlin integration	( SCGCQ01073874 ) 
 - Ventura: Using ALADIN GUI causes firmware 0x265D fault when collecting data.	( SCGCQ01074775 ) 
 - Tiger FPGA: NVMe drive drops off while running a mix of IOs and Task Managements	( SCGCQ01075180 ) 
 - Tiger is not seen from Ventura when dual paths are connected	( SCGCQ01076726 ) 
 - SAS SD Channels are per CSW block( SCGCQ01079052 ) 
 - Ventura: SPI library: SPI library does not detect NVSRAM on customer board that has micron flash	( SCGCQ01080680 ) 
 - Copyright information changed from 2015 to 2016 for NVDATA XML files.( SCGCQ01082212 ) 
 - Copyright header of nvdata xml files was not updated for year 2016( SCGCQ01082305 ) 
 - Tiger IOP: Route FPE started IO completions in firmware to the same path as the data	( SCGCQ01084691 ) 
 - Ventura: SPI library: SPI reset return value is not updated for the good case( SCGCQ01084964 ) 
 - Coverity defect: Constant expression result and Uninitialized scalar variable( SCGCQ01085576 ) 
 - Ventura: SPI library: Firmware fails to find NVDATA during flash scan in this particular flash part( SCGCQ01087673 ) 
 - Wrong sizeof argument usage and Condition check evaluates to TRUE always.( SCGCQ01088276 ) 
 - Uninitialized scalar variable usage.	( SCGCQ01088281 ) 
 - Coverity defect : Identical code for different branches.	( SCGCQ01089366 ) 
 - Ventura MSS: Correct MC Low Power settings( SCGCQ01089518 ) 
 - Tiger FPGA: Tiger timers are not accurate( SCGCQ01090040 ) 
 - Constant expression result always true( SCGCQ01092130 ) 
 - UART becomes unresponsive after hitting fault.( SCGCQ01093705 ) 
 - Ventura: comboserdes lib build all failure( SCGCQ01095056 ) 
 - Controller name not correct in HII( SCGCQ01095662 ) 
 - Ventura: 9400-8i/16i SGPIO Clock Signal Issue	( SCGCQ01105971 ) 
 - ComboSerdes: Function definitions for diagnostic functions are no longer visible to the expander SDK.( SCGCQ01109384 ) 
 - Marlin A0: Fault 0xEC30 while running NAKIncomingTLP-ModDataFCUpdate.jas script or link breaking	( SCGCQ01109436 ) 
 - Ventura: StorCLI timeouts while using Boot loader Cleantool to perform erase-all request	( SCGCQ01109588 ) 
 - ComboSerdes: Linker reports missing symbols	( SCGCQ01111993 ) 
 - Ventura: backend PCIe: add workaround for link recovery issue( SCGCQ01114258 ) 
 - Ventura: Endianess of MCTP Header word is incorrect	( SCGCQ01116031 ) 
 - Marlin MSS: Problems running dual rank( SCGCQ01117222 ) 
 - Aladin trigger causes firmware hang	( SCGCQ01117415 ) 
 - Ventura: Update RMC chip reset interrupt sequence.( SCGCQ01118899 ) 
 - Ventura MSS: Memory Controller pre-initialization settings need corrected.( SCGCQ01119681 ) 
 - Marlin MSS: Update some MC registers based on differences in new Cadence specification.( SCGCQ01122982 ) 
 - Ventura: make the FPE debug prints with timestamps consistent( SCGCQ01125471 ) 
 - Ventura: Controller hangs during heavy event logging	( SCGCQ01129539 ) 
 - Marlin A0: 0xD101 fault while issuing a full link break( SCGCQ01131880 ) 
 - Ventura/Marlin: backend PCIe: work around a link down issue( SCGCQ01134422 ) 
 - Fault xD060 seen when doing NVME glitching( SCGCQ01134928 ) 
 - Ventura RMC: Add capability to execute HW Workarounds at runtime based on chip revision.	( SCGCQ01136272 ) 
 -	( SCGCQ01137191 ) 
 - pl: backend PCIe: direct attached NVMe device may go missing after a port glitch	( SCGCQ01139383 ) 
 - Ventura: Make IOP_PCIE_FALSE_MSGUNIT_PARITY_ERR_WRITETHR_WORKAROUND dynamic( SCGCQ01139693 ) 
 - IOP: MCTP: MCTP Control Header was broken( SCGCQ01140942 ) 
 - IOP: MCTP: PCIe message hardware changes between products( SCGCQ01143327 ) 
 - Ventura: IT Bootloader Uses Wrong FLASH Layout and Faults( SCGCQ01144270 ) 
 - ventura: boot loader toolbox clean commands fail	( SCGCQ01144476 ) 
 - Incorrect Receiver EQ values are used in the enter bypass operation( SCGCQ01144500 ) 
 - Marlin: backend PCIe: NVMe devices in SFF-8639 JBOD may not be discovered( SCGCQ01145020 ) 
 - Ventura: NVME enabled partial nvdata with ACM still has old I2C controller numbers( SCGCQ01145049 ) 
 - BL/IOP: Marlin and Mercator not identified as unique products( SCGCQ01147332 ) 
 - PL: Overtemp LEDs not illuminating when thresholds are exceeded( SCGCQ01147743 ) 
 - Ventura: HostBoot fails with .75 release when board has blank flash( SCGCQ01148158 ) 
 - Ventura: SPI library: Flash write status ready check is using byte mask( SCGCQ01149967 ) 
 - Ventura: Firmware does not fault on some PCE errors( SCGCQ01152191 ) 
 - Added new PL fault code and also set default 60 secs for SATA hinting timer in PL( SCGCQ01152796 ) 
 - Marlin/Ventura: backend PCIe: various faults may occur if a link goes into recovery( SCGCQ01154122 ) 
 - DPA offset for Mercator is incorrect resulting in DPA functionaly not functioning( SCGCQ01154524 ) 
 - Ventura RMC: Add staggering of reset release to HW workaround for Hot Reset Link Regression.(SCGCQ01154562 ) 
 - IOP: MCTP: Wrong number of bytes received( SCGCQ01156025 ) 
 - Ventura: Firmware Faults with 0x2622 IFAULT_IOP_PCI_EXPRESS_ERROR_2( SCGCQ01158816 ) 
 - Marlin: DPA Changes Cause Mercator and Marlin to fail on PCE	( SCGCQ01159087 ) 
 - SPI library: Controller hangs during back ground operations.	( SCGCQ01161736 ) 
 - Ventura: DPA capability code causes Marlin family to fail on PCE	( SCGCQ01162151 ) 
 - Fault 0x4311 while running Target Mode IOs with Diag reset on Ventura( SCGCQ01163785 ) 
 - ComboSerdes: Hardware workaround for training failure( SCGCQ01164280 ) 
 - Update certain timing parameters for Dual Rank CA parity enabled configuration.( SCGCQ01164593 ) 
 - Ventura A0: Fault 0x1500 on Ventura A0 with tip code	( SCGCQ01165688 ) 
 - Ventura/Marlin: NVMe: completion queue head doorbell may not be written in a couple of error cases( SCGCQ01170592 ) 
 - With Spico version 0x1069 SAS links do not come up on Ventura( SCGCQ01171096 ) 
 - Ventura RMC: Implement new AVSO algorithm based on measuring Kp and leakage from EFuse.( SCGCQ01171316 ) 
 - Ventura: Firmware Upload COMMON_BOOT_BLOCK and CBB BACKUP return INVALID FIELD( SCGCQ01173710 ) 
 - Ventura: NVDATA XSD files have A0 in filename but apply to all revisions	( SCGCQ01173959 ) 
 - Host trace buffer does not contain expected data	( SCGCQ01174473 ) 
 - Ventura: SPI program is failing with small chunks of data( SCGCQ01175718 ) 
 - IOP: Intruder and Ventura PCIe hardware register names don't match( SCGCQ01176065 ) 
 - Starting Task Managements take a long time in certain conditions	( SCGCQ01176191 ) 
 - Ventura: B.0 Link Regression test failures on various systems.( SCGCQ01176840 ) 
 - Ventura RMC: Function Level Reset on OEM server fails after about 30,000 iterations	( SCGCQ01182485 ) 
 - Ventura RMC: Add staggering of reset releases to workaround issues with Hot Reset Link Regression.( SCGCQ01183501 ) 
 - SAS link resets sometimes fail( SCGCQ01185511 ) 
 - Unusual prints observed in debug console with Cutlass HBA while booting( SCGCQ01185627 ) 
 - Ventura: 9400 16i/8i boards XML doesn't have data setup for Sgpio config( SCGCQ01186085 ) 
 - Ventura NVDATA: ManPage13 (SGPIO	( SCGCQ01186241 ) 
 - UART command iop pci reg will cause fault 26B5 on Cutlass( SCGCQ01186359 ) 
 - IOP: Fix Aero build issues( SCGCQ01186963 ) 
 - Set Serdes Tx Eq values.	( SCGCQ01188034 ) 
 - Ventura: backend PCIe: link recovery issues( SCGCQ01188928 ) 
 - Ventura: SBR Reload workaround needs A15 firmware to set flag to indicate when RMC code should be reloaded.( SCGCQ01190075 ) 
 - Ventura/Marlin: resolve some undesired usages of the PL PCIe device support enable macro	( SCGCQ01191830 ) 
 - Ventura B0: Drive/Drives getting removed when running port reduction between HBA and expander( SCGCQ01196175 ) 
 - Ventura: SPI library: Macronix 32 MB flash fails to write upper 16MB in quad mode fails( SCGCQ01196202 ) 
 - CSW: SAS/PCIe dwell times and interrupt sequence modification for HW Cycling mode( SCGCQ01198294 ) 
 - Ventura RMC: Improve SysLite interrupt handling.	( SCGCQ01198340 ) 
 - pl: Unexpected SAS link operation with protocol cycling enabled( SCGCQ01198352 ) 
 - PL: Incorrect phy resets	( SCGCQ01199063 ) 
 - TX and RX train failures cause drives to link up at reduced rate	( SCGCQ01200626 ) 
 - SAS Power Management and PCal do not work together( SCGCQ01201827 ) 
 - Ventura B0: Seen 4311 Fault during lane break between HBA and the Capella switch	( SCGCQ01202315 ) 
 - Ventura: backend PCIe: various issues may occur if multiple switches have the same Device Serial Number	( SCGCQ01202401 ) 
 - Ventura B0: Expander goes missing when running port reduction between HBA and expander	( SCGCQ01205651 ) 
 - ROC-based IT boards won't power cycle or hot-plug( SCGCQ01207488 ) 
 - Ventura MSS: Dual rank VREF training results are 0x0D for all datapaths.	( SCGCQ01209224 ) 
 - ROM Bar Enable Bit set at boot time	( SCGCQ01211781 ) 
 - Ventura fails SAS Rx Training on Fast Silicon( SCGCQ01212572 ) 
 - Ventura/Marlin: The IOC exceptions bit 10 is set when backend PCIe was intentionally disabled( SCGCQ01213460 ) 
 - CSW: Compilation Error( SCGCQ01215027 ) 
 - Ventura B0: IO's stop to the drive with Fast Path Disabled and IOP RESET Disabled on the Controller( SCGCQ01218828 ) 
 - Targets attached to Quads 1 and 2 via active cable are not discovered on 9400-8e board.( SCGCQ01220915 ) 
 - Channel HBAs connector names are not unique	( SCGCQ01221189 ) 
 - Ventura: backend PCIe: link recovery testing issues	( SCGCQ01222761 ) 
 - Ventura: MCTP Storelibtest GetTopologyInfo causes a 0x265D fault	( SCGCQ01222778 ) 
 - Valid read eye window reported during initddr read leveling varies significantly on subsequent inits.( SCGCQ01230813 ) 
 - Marlin/Mercator: Marlin B.0 has unexpected initial Chip ID and Rev ID( SCGCQ01230921 ) 
 - Sas drives will not train after an NVMe drive is inserted then removed( SCGCQ01231705 ) 
 - Untimed busy wait during small data transfers( SCGCQ01233445 ) 
 - PCIe IO Unit Page 0 UART dump contains extra data than desired( SCGCQ01235005 ) 
 - Setting a common failure ISTATUS_IOP_FLASH_ERASE_FAILED for all the errors returned from Flash erase API	( SCGCQ01236701 ) 
 - Ventura: Hardware fails to load PCE SPICO if only the checksum is bad on SPICO SBR( SCGCQ01237819 ) 
 - SSC Profile and PLL BW Selection	( SCGCQ01243603 ) 
 - Cfgi library zeroed a shared scratch buffer( SCGCQ01248946 ) 
 - Change channel Tri-mode HBAs SGPIO frequency to 8.15KHz	( SCGCQ01250841 ) 
 - Create interface to adjust settings to improve Ventura Jitter( SCGCQ01250904 ) 
 - GoldenX does not create appropriate flash ROM image when two OpROMs (Legacy and UEFI	( SCGCQ01250935 ) 
 - Maxim regulator MFR_ID has changed, requesting official Mercator support for new MFR_ID="MA"	( SCGCQ01258257 ) 
 - Ventura B0: ManPage 9 Runtime configurations for Number of Virtual functions set to 16( SCGCQ01258786 ) 
 - Ventura/Marlin: backend PCIe: link not reinitialized after certain errors( SCGCQ01259639 ) 
 - Fault 0xECA0 is hit while running IOs on NVMe drives behind Ventura( SCGCQ01266097 ) 
 - PCI SIG PCIECV Compliance Test Failures (Non-Sticky Sticky bits( SCGCQ01268646 ) 
 - Ventura/Marlin: backend PCIe: completion timeout disable support failure( SCGCQ01269306 ) 
 - CSW: Modify 12g Tx settings( SCGCQ01272665 ) 
 - Firmware download failing when CPU speed reduced to 50%.	( SCGCQ01274688 ) 
 - Ventura: backend PCIe: improper interrupt control by workaround( SCGCQ01284095 ) 
 - HVD6 SERDES 3G/6G Attenuation Settings( SCGCQ01286488 ) 
 - Incorrect Copyright Information in NVDATA files	( SCGCQ01287001 ) 
 - Phase 3 Ventura FW doesn’t have NVMe Enabled NVDATA for 9405W-16e card( SCGCQ01288565 ) 
 - Ventura B0:9405W-16e:2 Phys of Quad are down when connected to an Expander via Active Cable( SCGCQ01288856 ) 
 - CSW: 4311 fault and 12g Rx Train timeouts( SCGCQ01288966 ) 
 - pl: backend PCIe: E984, E9A4, EF50, EF52 faults( SCGCQ01294948 ) 
 - Cutlass card is not detecting in SLOOB( SCGCQ01299390 ) 
 - CSW Library REF2 interrupt sequence is using the REF1 sequence length( SCGCQ01300905 ) 
 - Ventura/Marlin: backend PCIe: excessive supported switch count( SCGCQ01306811 ) 
 - More latency observed during device discovery( SCGCQ01311662 ) 
 - pl: backend PCIe: ECE4 fault	( SCGCQ01312345 ) 
 - Ventura/Marlin: backend PCIe: EC56 fault on link glitch	( SCGCQ01313075 ) 
 - Ventura/Marlin: build process performance improvement( SCGCQ01313151 ) 
 - Cutlass card is not detecting in SLOOB( SCGCQ01316544 ) 
 - Due to a timing issue a hang condition may occur on cold power up( SCGCQ01316806 ) 
 - (SATA Only( SCGCQ01317046 ) 
 - Design changes update on NVME drive hotswap feature and updating more changes( SCGCQ01319426 ) 
 - pl: NVMe: unexpected IO failures with firmware path read/write IOs to an NVMe SGL device	( SCGCQ01321013 ) 
 - pl: backend PCIe: specific vendor NVMe device does not appear to host software( SCGCQ01328743 ) 
 - SATA only drives getting removed when running SATA Passthorugh with incorrect data length along with IOs	( SCGCQ01329382 ) 
 - Corrected PORTERR debug print parameter size	( SCGCQ01329812 ) 
 - Ventura: Task Management to NVMe drives may not complete	( SCGCQ01330747 ) 
 - 0x6001 Fault due to a missing IO that went through the IO resubmit path	( SCGCQ01330777 ) 
 - Ventura: Detect invalid BP_TYPE types in VPP backplane Mgmt connector group	( SCGCQ01332062 ) 
 - Fixed SAS cleanup code to skip the PCI device instances.	( SCGCQ01332893 ) 
 - PL: SAS Notify Primitive Event not sent	( SCGCQ01332956 ) 
 - Task Management request of Abort Task to an NVMe device completes with failure status if the target of the Abort is not a currently active IO from the controller's point of view	( SCGCQ01334586 ) 
 - pl: NVMe: excessive NVMe init retry count if a serious PCIe error occurs	( SCGCQ01334997 ) 
 - Marlin B0: backend PCIe: EC6D fault on link glitch( SCGCQ01336021 ) 
 - Ventura IOP: VDM workaround bug fixes( SCGCQ01337547 ) 
 - ATA Passthrough MPT frame content has overwritten( SCGCQ01339127 ) 
 - Ventura: NVDATA option to ignore BP_TYPE check and force enable PCIe RefClk for NVMe backplanes( SCGCQ01349247 ) 
 - pl: NVMe: missing AccessStatus codes	( SCGCQ01352937 ) 
 - Fault 0x265d when posting target mode command buffers( SCGCQ01358077 ) 
 - NVMe-enabled firmware fails to host boot on a blank board( SCGCQ01358750 ) 
 - Fix dmDiagCmd( SCGCQ01367240 ) 
 - MR 7.4 - Mapping slot to targetID incorrectly( SCGCQ01368450 ) 
 - PL Fault 0000d073 LR 7f86abb5 during drive clear operation.( SCGCQ01368862 ) 
 - pl: NVMe: 6001 or E411 fault during task management( SCGCQ01371965 ) 
 - NVMe: ErrorResponseCount always equals ErrorResponseAllocationLength	( SCGCQ01373178 ) 
 - Ventura SBR: Changes to PLL reset requirements cause lock failure on some boards	( SCGCQ01373888 ) 
 - Ventura B0: 9400 IT Channel product firmware detecting memory read error during bootup( SCGCQ01375470 ) 
 - pl: backend PCIe: EC56 fault	( SCGCQ01376222 ) 
 - Assertion failure in ../../raid/log.c at line 2584: (code( SCGCQ01377047 ) 
 - NVDATA with changes in MR_PARAMS_PAGE0 upgrade does not take effect if personality is changed at least once by user.( SCGCQ01383923 ) 
 - Doorbell handshake hangs when faulted( SCGCQ01384089 ) 
 - Ventura BST 7.4==>Running I/O then PD pull and insert back hit MonTask: line 342 in file ../../raid/taskman.c rst=0( SCGCQ01384216 ) 
 - Ventura: FW may fault with 265D when attached to OEM NVMe backplane( SCGCQ01385700 ) 
 - Ventura 7.4 : Global divert counters does not get decremented to 0( SCGCQ01388033 ) 
 - Duplicate Event for Patrol Read Properties Change was removed( SCGCQ01389161 ) 
 - IOP: Improvements to AXI HWWA( SCGCQ01390095 ) 
 - storclif64 7.401.0.0: missing print telling user to reboot system after profile change( SCGCQ01390941 ) 
 - Drive model description missing on all SATA drives after changing to JBOD personality( SCGCQ01391694 ) 
 - Ventura B0: Missing signing supported firmware image in RO( SCGCQ01392675 ) 
 - pl: NVMe: reset types for some TM types mismatch MPI	( SCGCQ01392812 ) 
 - PCI SIG Compliance Test Failure - Test 1_8 Virtual Channel( SCGCQ01394426 ) 
 - PCI SIG Compliance Test Failure - Test 1_28 VPD Failure	( SCGCQ01394461 ) 
 - PCI SIG Compliance Test Failure - Test 1_41 Link Capabilities 2, Link Control 2, Link Status 2 Failures(SCGCQ01394478) 
 - Fix static code analysis tool detected defects	( SCGCQ01394714 ) 
 - MR_FW: Descriptor Format (DESC( SCGCQ01395709 ) 
 - MR7.4 PA2 8G Harpoon-8i JBOD mode: KA on target reset in a loop(SCGCQ01395837) 
 - Host TM : Cleanup the host dcdb timer code( SCGCQ01397478 ) 
 - Customer specific SAS 12g drive frequently links up at 6g.( SCGCQ01397553 ) 
 - vSES Target: Incorrect Enclosure Status Diagnostic Page Data for RECEIVE DIAGNOSTIC RESULTS with PAGE CODE=0x02( SCGCQ01397780 ) 
 - Ventura vSES : Various SCSI Commands to vSES target are not handled as per specifications.( SCGCQ01398992 ) 
 - Exception Stack Frame: FE705FC0" observed during OS boot	( SCGCQ01399366 ) 
 - MR 7.4 - VMWare 6.5 is not detected any partition at all after flashing to the latest ROP( SCGCQ01399718 ) 
 - Tast Abort Escalation Exception fix.	( SCGCQ01400118 ) 
 - Ventura BST 7.4 PJbod==> PD pull/insert hit MonTask: line 151 in file ../../raid/span.c rst=0( SCGCQ01400368 ) 
 - DeviceId in HostDcdbCallback is poulated incorrectly for JBOD personality( SCGCQ01400597 ) 
 - MR-7.4-PreAlpha: Controller not found after 1st TM on one EPD via debugger with "call DmTmPdTest devId 0" (RHEL 7.3 x64( SCGCQ01402358 ) 
 - MR 7.4 - Reinserted EPDs hit Exception mon_task	( SCGCQ01402849 ) 
 - NVMe drive discovery fails after pull/push on customer specific NVMe supported backplane	( SCGCQ01404209 ) 
 - The Avoid Duplicate Mid feature does not activate properly for expander attached SATA devices( SCGCQ01405083 ) 
 - Fix for DCMD target Reset regression from previous Task Abort escalation fix.( SCGCQ01405360 ) 
 - Ventura BST 7.4 PJbod==> Running I/O, OCR, and pull/insert PD hit MonTask: line 342 in file ../../raid/taskman.c rst=0( SCGCQ01406247 ) 
 - pl: NVMe: invalid Target Reset Method values should cause TM failure	( SCGCQ01406400 ) 
 - [PL]Ventura MR 7.5 - PL 00005851 hit while issuing OCRs with IO	( SCGCQ01406527 ) 
 - MR 7.4 - FW hit KA while I/Ong across all VDs( SCGCQ01406832 ) 
 - Ventura : Linux driver logs message, exp sasaddress is improperly printed when sas device discovery error event occurs( SCGCQ01406980 ) 
 - Performance drop in HDD Seq. Write up to %57	( SCGCQ01409242 ) 
 - Controller Fault (PL FaultCode = 00005805( SCGCQ01411046 ) 
 - MR 7.4 - Hitting DC after OCR on 240 EPDs( SCGCQ01412665 ) 
 - MR 7.4 pkg628 JBOD personality found SAS SSD pd as UnconfigBad after a cold boot( SCGCQ01412718 ) 
 - pl: NVMe: async event persistent conditions monitor issues( SCGCQ01414966 ) 
 - Internal Task Management operations not completing in out of resource conditions	( SCGCQ01415544 ) 
 - Ventura vSES: Protocol ID of additional element status page (0x0A( SCGCQ01416380 ) 
 - 0x6004 Fault during TM injection while running IO to Sata SSDs.( SCGCQ01416481 ) 
 - MR7.4: MFC subDeviceID changed from 9A60 to 9460 after FW flash in JBOD personality( SCGCQ01416483 ) 
 - When disabling one phy of a port the other phys of the same port do not relink after reset.	( SCGCQ01418575 ) 
 - When PFA drive is attached, it does not show predictive failure is detected.	( SCGCQ01420232 ) 
 - SPI Lib: SPI flash sector erase is taking to long.( SCGCQ01420695 ) 
 - BST 7.4 PJbod==> Pull/Insert 4 drives, but there is only one drive converted to EPD.	( SCGCQ01420781 ) 
 - MR 7.4: Drives become UBAD when reboot server( SCGCQ01422408 ) 
 - MR7.4: Found IOs drop while running Multipath cable pull 5min interval in linux( SCGCQ01422413 ) 
 - MR74 PA2: PD dropped on cable pull/push overnight( SCGCQ01422763 ) 
 - MR-7.4-PreAlpha: Intrusive FW debug messages when issuing "storcli /c0 show" in pkg 672( SCGCQ01422869 ) 
 - Change XSD major version to encode the phase, this avoids 7.3 NVDATA major version catch with 7.4 NVDATA major version number( SCGCQ01425178 ) 
 - IO failure( SCGCQ01427327 ) 
 - Change profile to 22 and reboot server hit Assertion failure	( SCGCQ01427332 ) 
 - 9405W-16i xml not available in Latest Release Order( SCGCQ01429439 ) 
 - iMR - Performance degrade at IO size greater than strip size - for Sequential Writes	( SCGCQ01430732 ) 
 - pl: Mode Select translation transfer length validation( SCGCQ01435884 ) 
 - 7.4 Alpha, restore controller defaults Cn causes a Montask( SCGCQ01437169 ) 
 - BSt Ventura 7.5 Profile21==> Set Drive Offline Failed.( SCGCQ01437184 ) 
 - storcli enabling of autoPdCache cmd caused firmware hitting exception( SCGCQ01437667 ) 
 - Increase the number of DMA frames for Profile 23	( SCGCQ01439382 ) 
 - MR 7.4 : firmware Discovery is not completed once in a while (across multiple Reboots( SCGCQ01439708 ) 
 - MR 7.4 : Configuration Loss Message displayed while moving from JBOD-> RAID with Logical disks.	( SCGCQ01439807 ) 
 - MR 7.4 : KA when run SG_RESET with EPD( SCGCQ01440421 ) 
 - SGPIO Clock driven Low on host PCIe reset assertion causing SGPIO target to latch on invalid data( SCGCQ01440481 ) 
 - MR 7.4 Crusader pkg705 while IO on VDs and JBODS then cablepull/push hit :Assertion failure in ../../dm/src/dm.c at line 1492( SCGCQ01440486 ) 
 - Ventura B0: Fault 0x510B while doing reboot test along with IOs & TMs( SCGCQ01440764 ) 
 - Spare filtering does not prevent NVMe PD from being used as spare for SAS/SATA array.( SCGCQ01441173 ) 
 - Disable user option to modify Multi Init/ SES Management/multiPath feature.	( SCGCQ01441181 ) 
 - MR7.4 HII shows enter your input when FW sets waitForKey bit	( SCGCQ01441329 ) 
 - Ventura FW packages need to be block the configuration of MFC settings from Megamon( SCGCQ01442546 ) 
 - MR 7.4 : Foreign import with Pinned Cache is failing and import successful after deleting pinned Cache.( SCGCQ01442565 ) 
 - HW Workaround:The PCIe host logic may incorrectly propagate a received ECRC error( SCGCQ01443186 ) 
 - 74AlphaPK720fw946: Slot order emumeration incorrect( SCGCQ01445001 ) 
 - Due to a bug in Serial Boot Loader (SBL( SCGCQ01446234 ) 
 - Restore enclosure topology info( SCGCQ01446265 ) 
 - MR7.4: Assertion Failure during cable-pull on dual path enclosure with EPD/VD I/O.( SCGCQ01446552 ) 
 - WG: LSA does not reflect requested personality in advanced controller properties, while moving from JBOD to raid	( SCGCQ01446799 ) 
 - MR7.4: FW hit Assertion failure in ../../dm/mpt2/mptframe.c at line 1247: mptIo!=NULL while IOs on 240LDs + Jbods( SCGCQ01447317 ) 
 - Fw/storcli need to hide profile 22 in jbod mode.	( SCGCQ01447393 ) 
 - 74Alphapk740fw957: Error restore cache while powercycle system for COL H740 Dell CTRL( SCGCQ01447514 ) 
 -	( SCGCQ01447767 ) 
 - GoldenX: When no BIOS option is selected the images are 1MB too small( SCGCQ01448015 ) 
 - Fix DM_PL_ProcessDiscoveryLinkStatus call in MptHandlePCIETopologyChgEvnt( SCGCQ01448310 ) 
 - WG: JBOD drive only lists operations start/stop locate after it were moved from online->offline and viceversa. Profile ID: 20( SCGCQ01448681 ) 
 - Ventura: NVMe : Log Sense Command Executed for Information Exceptions Log Page has TSD field set to 0b( SCGCQ01448752 ) 
 - A previous code change is missing a few changes.( SCGCQ01449239 ) 
 - MR RAID-mode profile 10 create vd cause pds for that vd offline( SCGCQ01450092 ) 
 - MR 7.4 - Not all reinserted PDs got detected that causing auto rebuild failed to start( SCGCQ01450215 ) 
 - MR 7.4 - FW hit KA while simulating multipath-cablepull( SCGCQ01450228 ) 
 - Fixing interrupt release in flash init code.	( SCGCQ01450387 ) 
 - PL trying to perform memory move using address which is in the non-addressable range	( SCGCQ01450399 ) 
 - pl: backend PCIe: link may fail to come up after link break	( SCGCQ01451278 ) 
 - megaraid firmware hangs on flash downgrade. issi flash, bristol board. going from fw SCGCQ01449686, downto fw SCGCQ01428525.	( SCGCQ01451327 ) 
 - Code size overflowed IOPATH section.	( SCGCQ01451888 ) 
 - MR 7.4 : Personality change from RAID to JBOD is successful on NVMe system.( SCGCQ01451959 ) 
 - For SATA SSDS, Enclosure ID is not showing.	( SCGCQ01452046 ) 
 - MR 7.4 - COL hit Assertion mon_task	( SCGCQ01452209 ) 
 - Initialize a larger part of MSIX vectors	( SCGCQ01452321 ) 
 - StorCli autoPdCache command does not create R0 LD from UNCONFG drives automatically	( SCGCQ01453911 ) 
 - Defect to track comments/defects from the review of ENH REQ SCGCQ01451570( SCGCQ01454633 ) 
 - pl: port enable may fail to complete if an OEM backplane is attached	( SCGCQ01455680 ) 
 - (VSES	( SCGCQ01458388 ) 
 - MR 7.4 - FW hit KA mon_task while simulating multipath FO( SCGCQ01458826 ) 
 - Assertion failure in ../../raid/taskman.c at line 342 while running TM sg_reset on SATA drives( SCGCQ01459626 ) 
 - Build script needs some prints to debug issue( SCGCQ01459659 ) 
 - MR 7.4 - PDs pull/push led to "Assertion failure in ../../cpu/arm/exceptions.c at line 938: 0"( SCGCQ01460017 ) 
 - Unmap capability checks should be done during hotspare commission not selection( SCGCQ01460055 ) 
 - Block threshold values were not set to optimal values( SCGCQ01460767 ) 
 - MR 7.5 ver 4.052 LSA does not have option to set/clear Transport Ready( SCGCQ01462694 ) 
 - Hot plugged NVMe drive fails to link up on OEM backplanes with ISTWI drive presence polling enabled( SCGCQ01463496 ) 
 - Move OOB Method Info from dynamic section to static section of NVRAM.( SCGCQ01464123 ) 
 - pl: NVMe: issues related to port enable completion( SCGCQ01464247 ) 
 - Updating from MR 7.1 to MR 7.4 FW package, with R5 and R6 in WT mode, after pulling and restoring power to system - cache data is lost.( SCGCQ01465056 ) 
 - Ventura: Firmware Update Algorithm Frees Mids Twice (SCGCQ01465058 ) 
 - Unmap is getting disabled on first VD after rebuild is complete with sliced VD's in drive group.	( SCGCQ01465788 ) 
 - MR7.4: Bios reports VDs missing at post during system reboot when CTRL in JBOD mode	( SCGCQ01466003 ) 
 - MR7.4: BIOS reports system has more than 256 disk devices when CTRL has less than 230 PDs in multipath( SCGCQ01466006 ) 
 - MR 7.4 : System hangs with continous DDF_CFG_ERR_BAD_VD_COUNT error messages when stocli show with foreign config on iMR	( SCGCQ01466568 ) 
 - Ventura BST 7.5(iMr	( SCGCQ01467132 ) 
 - Add new nvram variable to save the reset type( SCGCQ01467141 ) 
 - Firmware crash when format drive to PI support( SCGCQ01467357 ) 
 - Change version string to reflect 7.5	( SCGCQ01467368 ) 
 - To support the I2C bus reserve state in the case of UBM backplane( SCGCQ01470385 ) 
 - MR7.4: HDD global fault LED is not working for iMR controller (no LED lit up	( SCGCQ01470797 ) 
 - Ventura VSES: Incorrect data in diagnostic page 0xA when drive is missing but not yet removed.( SCGCQ01472941 ) 
 - To check if NVRAM changes related to upgrade/downgrade issue is present( SCGCQ01473186 ) 
 - Double Medium (ref tag( SCGCQ01474084 ) 
 - The "pl reg" command dumps the wrong amount of data for some structures.	( SCGCQ01474266 ) 
 -	( SCGCQ01475119 ) 
 - MR7.4: PDs going into Shield/Failed state during during cable-pull on dual path enclosure with EPD/VD I/O.( SCGCQ01475138 ) 
 - Update OOB_METHOD_INFO_NVRAM to fix compile issue( SCGCQ01475161 ) 
 - Assert can occur when applying iButton/iButtonless Licensing settings that is typically done in a manufacturing environment.	( SCGCQ01476342 ) 
 - PL: SATA: Sense Key/Additional Sense code incorrectly set when open zone issued on a Security locked SMR drive( SCGCQ01478037 ) 
 - MR 7.5: DISM hang during bootup with SSD disks connected	( SCGCQ01478082 ) 
 - Intel MR7.4 Unable to set RAID profile 11 & 12 (ROP 820 and newer affected( SCGCQ01478714 ) 
 - the multi-init multi path change are not support	( SCGCQ01478725 ) 
 - Ventura B0: Controller Reset causing OS hang and resets( SCGCQ01480987 ) 
 - Fix merge issues while delivering to 7.5	( SCGCQ01481168 ) 
 - Additional changes needed for SCGCQ01470741: 930-16i Cannot Spinup HDD During System Power On.( SCGCQ01482688 ) 
 - MPI SEP request to Slots with invalid SES Page 0A element index may not complete	( SCGCQ01482937 ) 
 - Skinny build failed	( SCGCQ01483001 ) 
 - Revert - SCGCQ01465056 MR7.4: Upgrade from MR7.1 to MR7.4 cache data loss.( SCGCQ01483182 ) 
 - pl: NVMe: improved fix for 6001 fault( SCGCQ01484382 ) 
 - pl: 265D fault on 'pl dbg' before port enable( SCGCQ01485059 ) 
 - Ventura/Marlin: Firmware Download does not protect user from downgrading to firmware that does not support Winbond( SCGCQ01485441 ) 
 - Host application hangs waiting for completion of IO issued after NVMe device is removed( SCGCQ01486695 ) 
 - MR7.4 Beta: Direct Attached SAS HDDs go Unconfigured Bad at Power-On (ROP 834 & earlier is OK( SCGCQ01487263 ) 
 - PL: Modify internal structures( SCGCQ01487864 ) 
 - Intermittent Update firmware failed with M0 using EFI StorCLI( SCGCQ01487866 ) 
 - Global HDD LED may not indicate IO activity for NVMe or SAS drives( SCGCQ01489030 ) 
 - Code Unstable in Common_Main, Re definitions of Macro IOP_TIMED_CONDITION, consolidating them.( SCGCQ01489981 ) 
 - OOB SLT get errror when getting send, getobjstatus and getttylog.( SCGCQ01491291 ) 
 - 0x7C41 Fault doing IOs and Task Managements on a mixed SAS/NVMe topology.( SCGCQ01494379 ) 
 - pl: SATA: port enable may time out on spinup failure	( SCGCQ01496842 ) 
 - IOP MCTP: Changes missing from a previous code change( SCGCQ01497080 ) 
 - Aero (Talladega( SCGCQ01498117 ) 
 - Ventura FW may fault on single bit correctable ECC errors in IOA Local RAM( SCGCQ01503262 ) 
 - Can not change the profile back to "A" once you are in profile "B" and flash the controller to FW that does not support NVMe	( SCGCQ01503509 ) 
 - Fixing coverty defects 19848 & 19838	( SCGCQ01504066 ) 
 - pl: backend PCIe: LTSSM state wait during hot reset( SCGCQ01504310 ) 
 - New Event required for individual PD PR completion( SCGCQ01504936 ) 
 - Ventura: Slot LEDs on SGPIO based backplane may not blink( SCGCQ01505392 ) 
 - MR7.3.1 : controller reset seen while importing 32 VD foreign config	( SCGCQ01506874 ) 
 - MR7.5: Firmware asserted at ddf/ddf.c at line 1377: ld == vdRec->Populated_VDEs when insert NVMe drives( SCGCQ01509362 ) 
 - (SATA Only( SCGCQ01509632 ) 
 - Intel S2600WF System Drive Activity LED Stays On w/ Columbia Dunes (9460-8i( SCGCQ01511995 ) 
 - MR7.5: Firmware hang during power up after power failure with COL( SCGCQ01516975 ) 
 - FW incorrectly reports LD unit attention pending irrespective of the scsi op code( SCGCQ01518712 ) 
 - Information on cfgi dump of SASIoUnitPage1( SCGCQ01522331 ) 
 - pl: backend PCIe: 4311 fault with NVMe enabled (part 2( SCGCQ01522342 ) 
 -	( SCGCQ01522627 ) 
 - Firmware hangs due to DISM not completing( SCGCQ01525140 ) 
 - Win, MR 7.5 ROP 970 , R0, 16DC 12G-SAS HDD shows, 9% to 10% SW performance drop at 4k at QD16( SCGCQ01529277 ) 
 - SR, RR, and OLTP regressions up to -90% on 24 Single Drive R0 Config	( SCGCQ01531736 ) 
 - Win/Lin MR7.5 ROP 970,RAID5,%5 to 12% OLTP performance issues at QD1 & R5\R6 QD64 (all IOsizes( SCGCQ01532879 ) 
 - Stark system hangs during the reboot test at boot.( SCGCQ01548923 ) 
 - MR7.5: Firmware asserted during cable pull with IO on JBODs and taskmgmt reset( SCGCQ01555097 ) 
 - OOB slt can not see the imr controller( SCGCQ01561552 ) 
 - After VD erase, In the Action menu, It is not changing from Stop Erase to Erase( SCGCQ01561897 ) 
 - Issue: JBOD devices were dropped after unloading driver and reloading driver in linux( SCGCQ01566087 ) 
 - Change UNMAP support from enable to disable( SCGCQ01566954 ) 
 - pl: backend PCIe: 4311 fault (part 3	( SCGCQ01571588 ) 
 - 9440-8i card: drop out UG drive, error LED always ON. Error LED turns off only upon reinsertion of the drive.( SCGCQ01577475 ) 
 - sysDMA attempted on core1 cause FW to choke( SCGCQ01583517 ) 
 - pl: backend PCIe: ED8D fault	( SCGCQ01628411 ) 
 - MR7.5 18B CIT : if connection to EKMS is lost while online, drives are not in proper state after reboot( SCGCQ01670320 ) 
 - Inconsistent CC progress % is logged after reboot during CC	( SCGCQ01683057 ) 
 - [iMR7.5] Memory allocation failure during RAID operation cycles under high loading( SCGCQ01697700 ) 
 - pl: NVMe: ED8D fault	( SCGCQ01698373 ) 
 - PL: Chassis Slot Valid Flag is Incorrectly Cleared in Enclosure Page 0( SCGCQ01715509 ) 
 - Cannot stop patrol read on PD with medium errors by the stop cmd	( SCGCQ01715992 ) 
 - IR : Resync can be Pending and in progress at the same time on a Raid 10 Volume( SCGCQ00138417 ) 
 - Fix unused variable warning in I2C codes	( SCGCQ00140588 ) 
 - Unable to execute diagnostic console commands after fault( SCGCQ00141555 ) 
 - (IOP-Only( SCGCQ00142962 ) 
 - Flashing a thunder bolt or meteor with DDR enabled FW cause a 1808 fault followed by a recursive 265d fault( SCGCQ00143378 ) 
 - Removing dead code for volume inline update	( SCGCQ00145728 ) 
 - IOP: Diagnostic Console xget commands fixed	( SCGCQ00146562 ) 
 - Infinite loop when using FPGA and Trident and Boot loader( SCGCQ00149422 ) 
 - Firmware faults while booting with DDR disabled in NVData( SCGCQ00149423 ) 
 - SAS-3 FW FPE Checkpoints Interfere with Code to Decrement the IO Count( SCGCQ00151849 ) 
 - Defects found in init code review fixed( SCGCQ00152229 ) 
 - Compilation error with Power Mgmt Code( SCGCQ00156158 ) 
 - Unitialized variable in firmware upload command handler( SCGCQ00157647 ) 
 - RMTFLASH scripts can fail when programming the main FW image into FLASH( SCGCQ00158086 ) 
 - Corrupted PPC instructions at the end of the function iopSched	( SCGCQ00161664 ) 
 - tlbInitNvsram( SCGCQ00164720 ) 
 - IOP: PCIe Reply Queue FIFO index overflow work around( SCGCQ00168591 ) 
 - Write IOs stall during task management( SCGCQ00169848 ) 
 - When using Fast Path Timer, IO Count could get corrupted	( SCGCQ00170066 ) 
 - Workaround for ctrlupd_req signal in Cobra DDR3	( SCGCQ00172023 ) 
 - Fault 0x0610 occurs during Message Unit Reset( SCGCQ00172125 ) 
 - Build fails because of Small Data Area overflow	( SCGCQ00176456 ) 
 - PPC476 TLB parity not being properly initialized	( SCGCQ00181733 ) 
 - Fault 0x5826 when running Task Management tests	( SCGCQ00183297 ) 
 - Various IOP firmware fixes for A0 silicon( SCGCQ00186025 ) 
 - CLI Command Reports PCIe Link Speed and Width Incorrectly( SCGCQ00187285 ) 
 - Phy link rate does not follow MaxMinLinkRate in sas io unit page 1( SCGCQ00187614 ) 
 - Fix SysDMA test firmware	( SCGCQ00187760 ) 
 - Core reset results in missing interrupts	( SCGCQ00188810 ) 
 - PCI-Express Link Layer registers inaccessible( SCGCQ00188937 ) 
 - First set of changes to DDR3 library from validation/bring-up( SCGCQ00189172 ) 
 - Missing MSI-X interrupts and replies after message unit reset( SCGCQ00193609 ) 
 - (NVData( SCGCQ00194017 ) 
 - Prototypes for iopiMid2PtrMsg( SCGCQ00194557 ) 
 - Invader firmware gets stuck waiting for the Reply Post Queue to become not full( SCGCQ00203395 ) 
 - (NVData	( SCGCQ00204610 ) 
 - DDR3 through-put is not as high as expected( SCGCQ00204630 ) 
 - PL does not handle completion from IOPCompletionQueue for PL Light IOs( SCGCQ00205349 ) 
 - Fixes to handle "Global Power Management Change" MPI request parameters and display proper power management modes in IOU Page 7 at start of day.	( SCGCQ00205370 ) 
 - Fix build error( SCGCQ00205595 ) 
 - PCI-Express hardware issue in systems supporting TPH	( SCGCQ00205727 ) 
 - Work around Reply Queue port reply entry loss( SCGCQ00206002 ) 
 - Gen3: PwrMgmt- IoUnitPg7's 'Board Temperature' field reports random data.( SCGCQ00206329 ) 
 - Invader A0- D027 fault when disabling 3 phys when stress is running in a target and initiator mode setup	( SCGCQ00207040 ) 
 - Firmware lockup when using two CLI sessions simultaneously( SCGCQ00207538 ) 
 - Fault code 0x0012 is used twice( SCGCQ00209961 ) 
 - Fault 0000130D( SCGCQ00210292 ) 
 - Hearbeat LED does not display hte fault code when controller has faulted	( SCGCQ00210298 ) 
 - System DMA error not causing a firmware fault( SCGCQ00213368 ) 
 - Invader: Updated the FW work around tables for the B0 release.( SCGCQ00218436 ) 
 - Corruption on writes to memory during read-modify-write( SCGCQ00220982 ) 
 - Workaround for LMIDs in exception queue having wrong VF_IDs( SCGCQ00222933 ) 
 - (FPGA/Palladium( SCGCQ00223234 ) 
 - EthHAL: MAC address programmed into hardware backwards( SCGCQ00223376 ) 
 - Fixed adapter resets when a SAS IO Unit Control Request is issued with Operations related to Fast Path( SCGCQ00224193 ) 
 - Invader FPGA: Invalid MIDs getting used for local messages( SCGCQ00224208 ) 
 - Diag buffer generates incomplete trace entries( SCGCQ00225167 ) 
 - Fault 0x265D	( SCGCQ00225369 ) 
 - Invader EthHAL: ethiReceiveFrame( SCGCQ00227343 ) 
 - I2C reads to specific offset in a SEEPROM device might fail( SCGCQ00227919 ) 
 -	( SCGCQ00228765 ) 
 - D072 Fault	( SCGCQ00229676 ) 
 - Invader A0: Global Power Management State can still be changed when it hasn't Taken Control.	( SCGCQ00231505 ) 
 - Roam of Gen2 IR volume to Gen3 and back requires changes in order for scrub duration to be handled.( SCGCQ00231723 ) 
 - Fault 0xD033	( SCGCQ00235681 ) 
 - 0x265D fault may occur when printing the ring buffer	( SCGCQ00237185 ) 
 - Fault 0x2667 when trying to register a diag trace a second time( SCGCQ00242016 ) 
 - AHQD CSETs were done incorrectly.( SCGCQ00243082 ) 
 - (SR-IOV Only	( SCGCQ00243150 ) 
 - Fault 0x2623 while attempting to boot with an Invader A0 in a Dell Poweredge 2970( SCGCQ00248637 ) 
 - Fury does not see all the drives when DDR is enabled in Manufacturing Page 11( SCGCQ00251457 ) 
 - ONFI: The return type of U64 is not compatible in Linux environment	( SCGCQ00251506 ) 
 - MSI-X Table Size field is improperly formatted( SCGCQ00254493 ) 
 - RmtFlash: Returns invalid status	( SCGCQ00254879 ) 
 - 0x0810 fault when booting after power cycling 11 enclosures	( SCGCQ00255194 ) 
 - sas2flash can not erase firmware if DDR is enabled in the nvdata	( SCGCQ00263211 ) 
 - (IOP	( SCGCQ00265408 ) 
 - IOP Fault 0x265D occurs during non-FPE IO( SCGCQ00279463 ) 
 - When doing Task Managmeent cleanup, an invalid Parity error may be caused by HW cleanup	( SCGCQ00280175 ) 
 - Ping utility has potential for out of bounds array access.( SCGCQ00282732 ) 
 - IOP: Fault 0x26B1 encountered after Powerloss signal is deasserted( SCGCQ00290633 ) 
 - Fault 6108 used in multiple places.	( SCGCQ00291410 ) 
 - MPI PMC request message with the Feature set to PORT_WIDTH_MODULATION - FAILS( SCGCQ00293376 ) 
 - DIS mis-compare due to bad restore's DMA Descriptors	( SCGCQ00296967 ) 
 - 0x130A fault when running firmware on other flavors 3108 controller( SCGCQ00301169 ) 
 - RAID1 volume fails to resync when compatible drive is available	( SCGCQ00317642 ) 
 - Using the Diagnostic RW registers after a chain pull causes PCIe lock up	( SCGCQ00320990 ) 
 - Invader B0: Fix Diag Trace release starting offset	( SCGCQ00321917 ) 
 - Drive loss causes when direct attached expander is flagged as removed( SCGCQ00338053 ) 
 - Initial bring up in lab for AHCI	( SCGCQ00356058 ) 
 - Back end PCI interrupts are not enabled	( SCGCQ00357192 ) 
 - DDR3 : ddriEnableForceEccError( SCGCQ00361334 ) 
 - Need UART commands to show backside PCIe information	( SCGCQ00364512 ) 
 - Internal tool fix, does not affect FW( SCGCQ00391082 ) 
 - No functional change	( SCGCQ00395325 ) 
 - Timers are longer than expected on FPGA	( SCGCQ00397134 ) 
 - RAIDContextOfffset field in Message Config Registers are not correct	( SCGCQ00397602 ) 
 - (BUILD ONLY( SCGCQ00398135 ) 
 - (IOP	( SCGCQ00408393 ) 
 - PCIe discovery doesn't work for AHCI behind PCIe switch	( SCGCQ00412140 ) 
 - NVMe: Nonzero SkipCount doesn't work very well( SCGCQ00412150 ) 
 - Duplicate LMIDs might be present in the hardware FIFO causing 0xD065, 0xEC0F faults during FastPath IOs	( SCGCQ00432573 ) 
 - PL: SGL print for debug may not work properly( SCGCQ00433625 ) 
 - Document Defect: SAS 3.5 Firmware Summary Release Notes Incorrect( SCGCQ00435723 ) 
 - E00E fault occurs during heavy IO to AHCI devices( SCGCQ00449814 ) 
 - PL: ownership of frame containing a non read write IO to a backend PCIe device( SCGCQ00456377 ) 
 - CM fails to detect a switch attached NVMe device	( SCGCQ00479121 ) 
 - Build fails when PL_FEATURE_PCI_DEVICE_SUPPORT macro disabled( SCGCQ00481604 ) 
 - IO timeouts or D071 fault during task management with backend AHCI device( SCGCQ00484044 ) 
 - Backend PCIe completion timeout prevention bugfixes	( SCGCQ00505131 ) 
 - E002 fault occurs during AHCI task management( SCGCQ00505719 ) 
 - NVMe: LUN not validated before use in non read write translations( SCGCQ00562314 ) 
 - uatx.mak build doesn't work	( SCGCQ00569052 ) 
 - AXI2SHELLRegisters.h fails to build	( SCGCQ00573497 ) 
 - Intruder/Ventura: Update I2C4 select register offset	( SCGCQ00574166 ) 
 - NVMe: handling of admin queue full condition during NVMe async event handling( SCGCQ00600515 ) 
 - Config page accesses time out( SCGCQ00604559 ) 
 - With PL_FEATURE_PCI_DEVICE_SUPPORT disabled, improper MPI status sent back to config Requests( SCGCQ00613854 ) 
 - Ventura: The IFSR and DFSR error flags are not cleared on reset( SCGCQ00618466 ) 
 - 26B5 fault on backend PCIe link down	( SCGCQ00640436 ) 
 - "Rsvd15" prints with FxCore IOs	( SCGCQ00663642 ) 
 - Ventura: System stack is not dumped for backtrace( SCGCQ00675391 ) 
 - Fault 0x265D running IO on Linux OS	( SCGCQ00677801 ) 
 - Intruder FW halts at boot with 2.0 bitstream	( SCGCQ00685756 ) 
 - Ventura: Need required external defines and header file ordering to include SCS FW libs in IOP( SCGCQ00697063 ) 
 - Intruder: Fix issues in FW controlled spinup	( SCGCQ00710609 ) 
 - VENTURA: update SPI library to set continuous mode counter( SCGCQ00730738 ) 
 - Ventura: Small Data Area overflow in compile/link operation( SCGCQ00735463 ) 
 - Remove redefinition of IOC_NUM_PHYS( SCGCQ00736730 ) 
 - Ventura: Backtrace.pl needs to be updated to account for firmware mapping( SCGCQ00747268 ) 
 - Dauntless FPGA: 0900 fault after Linux driver load with AHCI device	( SCGCQ00751416 ) 
 - Backend PCIe: periodic dev init state check shouldn't run if init isn't running	( SCGCQ00760618 ) 
 - Ventura: SPI-FLASH Boot Fails( SCGCQ00769262 ) 
 - Internal Build Tool Error( SCGCQ00770250 ) 
 - Ventura: SCSI IO's fail due to invalid Virtual to Physical Translation( SCGCQ00779552 ) 
 - Intruder (ethHal	( SCGCQ00786810 ) 
 - Ventura: SPI library - NVSRAM write is not persistent after power cycle( SCGCQ00802389 ) 
 - Backend PCIe: EC0F or D065 faults during PCIe task management( SCGCQ00804044 ) 
 - IOP Pointers for Ext Mfg Pages 42/43 Are Calculated Incorrectly at Start of Day( SCGCQ00814416 ) 
 - NVDATA: BusNum/ISTWIControllerNum for SBR in Ext Mfg Page 43 is Incorrect( SCGCQ00814422 ) 
 - IOP directly accesses PL instead of using PLI( SCGCQ00820292 ) 
 - Build: Customized NVData files can be overwritten during the build process( SCGCQ00831527 ) 
 - IOP: Firmware fault on Intruder A0 will trigger recursive 0x265E	( SCGCQ00833018 ) 
 - Ventura: fwheadx compile error( SCGCQ00838005 ) 
 - Ventura: backend PCIe: some bringup changes	( SCGCQ00841065 ) 
 - Ventura: SysDMA FPGA Problem Fixed( SCGCQ00842462 ) 
 - Round 1 of fixes for issues found while performing basic dev test for PCIe error interrupt path	( SCGCQ00843113 ) 
 - Unmap FIS Port Translation Hangs if No Range List Entries are Generated( SCGCQ00844030 ) 
 - IOP (Ventura	( SCGCQ00849743 ) 
 - nvdata.xsl not present in IT release package	( SCGCQ00849795 ) 
 - Cutlass: Firmware download fails when using Cutlass production boards( SCGCQ00851669 ) 
 - Ventura: Fault 265D when pl dbg dumps PtrHwDmaQFreePointer( SCGCQ00852104 ) 
 - IOP: Remove fault 0x1801	( SCGCQ00852302 ) 
 - SAS3.5FW has tabs in source code	( SCGCQ00852767 ) 
 - Ventura: modify some debug info( SCGCQ00856678 ) 
 - Ventura : Rmtflash build error( SCGCQ00860460 ) 
 - Fault 0xEC60 starting IO	( SCGCQ00860763 ) 
 - Rearrange PDB RCC interrupt handlers to avoid spurious interrupts( SCGCQ00862058 ) 
 - Ventura: backend PCIe: PL translated PCIe read/write IOs may time out( SCGCQ00869263 ) 
 - PL: Remove Unused Fault Codes( SCGCQ00872313 ) 
 - NVDATA: Correct SubSystem Vendor ID( SCGCQ00872784 ) 
 - Ventura FPGA: 0xEC9D during PCIe task management	( SCGCQ00872879 ) 
 - Fix the "Check Header" function of the RBD tool.	( SCGCQ00879401 ) 
 - Ventura: Main firmware region gets programmed twice	( SCGCQ00884089 ) 
 - CSW Library header file names are not unique	( SCGCQ00884495 ) 
 - Ventura FPGA: TM to devices behind switch failing( SCGCQ00895687 ) 
 - Ventura: Number of MSIX vectors is 16( SCGCQ00896514 ) 
 - IOP: Fix compilation issues	( SCGCQ00902089 ) 
 - Ventura: PCIE_MAX_PCI_FUNCTIONS not in a distributeable file	( SCGCQ00905007 ) 
 - To resolve the build all issue for the code check-in ER SCGCQ00888047( SCGCQ00914293 ) 
 - IOP & PL: Move certain PL structures to use OCM PLB Segment 2( SCGCQ00917625 ) 
 - IOP: Disable interrupt tracking feature	( SCGCQ00917700 ) 
 - Ventura: Dauntless min build fails with GPIO wide port group mapping changes	( SCGCQ00923022 ) 
 - Tiger: Remove SUCCESS (1	( SCGCQ00925729 ) 
 - Ventura: backend PCIe: incorrect link rate may be reported in PCIe IO Unit Page 0	( SCGCQ00925861 ) 
 - Spico interrupt timeout after 500 Sbus loops is reported by the library	( SCGCQ00940213 ) 
 - BL: Tiger: IT firmware fails to boot	( SCGCQ00941168 ) 
 - A15 does not boot successfully from SPI flash after adapter reset( SCGCQ00947330 ) 
 - Ventura: OCM Valid Flags are Incorrect for some configurations( SCGCQ00948910 ) 
 - Tiger FPGA: 0x5854 when posting Trace Buffer during IO	( SCGCQ00950016 ) 
 - Ventura: Remote FLASH Utility Doesn't Print to UART0	( SCGCQ00950134 ) 
 - Ventura: Not able to download the image to the Ventura controller( SCGCQ00952625 ) 
 - Tiger: ensure PL memory is zeroed at start of day( SCGCQ00952695 ) 
 - Ventura: backend PCIe: fix some config page related bugs	( SCGCQ00954691 ) 
 - Ventura: backend PCIe: NVMe devices or PCIe switches intermittently fail to link up	( SCGCQ00987792 ) 
 - Ventura A0: Erasing board produces unwanted UART prints	( SCGCQ00988616 ) 
 - Ventura: previous NVDATA version is always 0xFFFFFFFF( SCGCQ00988621 ) 
 - MiniDMA updates necessary for DDR4 bringup on Ventura A0.( SCGCQ00991769 ) 
 - IOP: Intruder: Firmware download through Sas3Flash or equivalent utility fails with return IocStatus 0x8004	( SCGCQ00997542 ) 
 - IOP: Intruder: SBR Load error print caused due to wrong ordering of bit-fields inside the internal structure	( SCGCQ00997544 ) 
 - Ventura: Fix typo in register definition name( SCGCQ01002334 ) 
 - Ventura A0 : MSS : Some bug fixes( SCGCQ01012325 ) 
 - Tiger: TLPs from NVMe drives have incorrect requester ID on egress at host port( SCGCQ01015401 ) 
 - IOP: Temporary chain memory buffer allocated with the wrong size	( SCGCQ01015465 ) 
 - IOP: Stryker sends events using MSIx index 1	( SCGCQ01016001 ) 
 - Tiger: TM aborted IO on Tiger was not using the FW reply path, instead the success reply route was used	( SCGCQ01017369 ) 
 - SGPIO Locate function is not working on particular controller board	( SCGCQ01019498 ) 
 - Ventura: backend PCIe: incorrect descriptor type returned on firmware path NVMe encapsulated completion	( SCGCQ01024109 ) 
 - Tiger IOP: Remove SysDMA FPGA workaround	( SCGCQ01024671 ) 
 - Tiger FPGA: Fix some remote core IOA IO print strings( SCGCQ01024713 ) 
 - Ventura NVData: Manufacturing Page 9 has incorrect value in NumResources	( SCGCQ01027223 ) 
 - PL: Fault code 0xD091 is in multiple locations( SCGCQ01029667 ) 
 - Tiger IOP: UART unresponsive when running NVME IO that requires FW handling( SCGCQ01032056 ) 
 - Ventura: NVMe and non-NVMe performance tuning( SCGCQ01039059 ) 
 - Ventura: PL Fault 0000d073( SCGCQ01039143 ) 
 - Ventura Tiger: Unsupported/Failed Task Managements should also be forwarded to Tiger before failing back to host	( SCGCQ01041510 ) 
 - Tiger: Implement workaround for PSB failure to transmit message TLPs	( SCGCQ01044060 ) 
 - Ventura: backend PCIe: miscompare may occur after link glitch between HBA and PCIe switch( SCGCQ01046343 ) 
 - PL: Mid reuse may cause data miscompare( SCGCQ01047691 ) 
 - SPI Library: Initialization failing to find devices is covered up( SCGCQ01047701 ) 
 - FW entered PL Fault 0000d0d1 while I/Oing across LDs	( SCGCQ01059682 ) 
 - Tiger FPGA: Task Management to an NVMe drive causes the drive to drop off( SCGCQ01065218 ) 
 - Modify filter of dual VREF range optimization.( SCGCQ01068008 ) 
 - NVMe: Incorrect Informational Exceptions log page for NVMe Drives( SCGCQ01070221 ) 
 - Ventura: B0 requires check of enqueue register before disabling queue manager state machine( SCGCQ01070612 ) 
 - Marlin controller as a target device is not always discovered by test tool( SCGCQ01074546 ) 
 - IOP: Fix build all error when building Ventura firmware with SED support	( SCGCQ01075241 ) 
 - IOP: Expected features were incorrectly compiled out	( SCGCQ01080016 ) 
 - Tiger: ENABLE_CONFIG_SPACE(	( SCGCQ01090035 ) 
 - Uninitialized return variable( SCGCQ01091185 ) 
 - IT: "iop xget trace" doesn't work( SCGCQ01109405 ) 
 - ComboSerdes: TXEQ settings hash table is missing the SATA 3G defaults( SCGCQ01126640 ) 
 - Ventura: Add new reset algorithms to RMC to support SBR Reload( SCGCQ01131809 ) 
 - Ventura/Marlin: backend PCIe: reliability of link bandwidth change notification	( SCGCQ01138343 ) 
 - Ventura B0: Fault 0x265D while Load/unloading drivers( SCGCQ01139214 ) 
 - Ventura A0: Using 9400-16i partial NVMe enabled XML file doesn't discover direct attached NVMe devices( SCGCQ01143427 ) 
 - Incorrect flash offset is being calculated for full flash write	( SCGCQ01144266 ) 
 - IOP: Firmware is not notified of received PCIe VDMs when MemSpaceEn is clear	( SCGCQ01144917 ) 
 - Marlin/Ventura: Add L0s state work-around( SCGCQ01149895 ) 
 - Venture RMC: Add AVSO code to handle un-programmed Infineon regulators.( SCGCQ01152197 ) 
 - Ventura: Fix bad Clear Case AutoMerge	( SCGCQ01154480 ) 
 - Marlin MSS: Null pointer encountered when performing MSS register dump before performing DDR initialization( SCGCQ01162002 ) 
 - Tomcat iMR - Performance degrade at IO size greater than strip size	( SCGCQ01164595 ) 
 - PL: Possible null pointer access in a non-automated SATA Response Frame	( SCGCQ01168086 ) 
 - PL: Unchecked function return value in sata code	( SCGCQ01169267 ) 
 - MSS Ventura performance enhancements	( SCGCQ01172218 ) 
 - EVT3: 9400-16i PCIe NVME Ref Clock is missing on 2 of the 4 internal connector ports	( SCGCQ01176652 ) 
 - Ventura: ISTWI tool compiled out of IOP (returns INVALID FIELD( SCGCQ01177983 ) 
 - Ventura B0 MSS: Training failures when halfmode enabled.	( SCGCQ01178243 ) 
 - Ventura: Toolbox command (ISTWI Read Write Tool Request Message	( SCGCQ01180813 ) 
 - Ventura: RMC Match Detection Doesn't set Write Enable to Register File( SCGCQ01191760 ) 
 - Ventura: IOCInit request succeeds when the HostPageSize is invalid( SCGCQ01194895 ) 
 - Ventura: backend PCIe: compatibility tweaks for NVMe devices	( SCGCQ01201787 ) 
 - PL: Remove unused fault codes and correct documentation issues in pliFault.h	( SCGCQ01202876 ) 
 - Validate mid in Tx openfail cleanup( SCGCQ01215592 ) 
 - Incorrect Phy slot mapping and connector names on Channel HBA NVDATA xmls.	( SCGCQ01217015 ) 
 - Ventura: Large Latencies observed using MCTP over PCE with some BMC's( SCGCQ01217762 ) 
 - bld all failure due to CSET SCGCQ01213000( SCGCQ01228855 ) 
 - Ventura B0: 9400-16e : Only 2 of the 4 direct attached drives are discovered for Quads 1 and 3 of the controller.( SCGCQ01234249 ) 
 - Valid readeye check fails in halfmode and noecc.	( SCGCQ01234511 ) 
 - Customer board faults during System POST when run on Purley platform	( SCGCQ01234713 ) 
 - pl: NVMe: Abort Task may abort an IO when it is still outstanding at the device( SCGCQ01235948 ) 
 - Marlin: Current build for marlin uses old A.0 SPICO	( SCGCQ01235975 ) 
 - Marlin: Add additional support for cold boot fix	( SCGCQ01251641 ) 
 - Marlin RMC: PC locking up on AHR	( SCGCQ01251657 ) 
 - Marlin: Fix IOP_INVALID_PCI_REVID_WORKAROUND so that it only applies to Marlin A.0 and Ventura( SCGCQ01251737 ) 
 - Changed copyright year 2015, 2016 and 2015-2016 to 2015-2017 in Ventura nvdata files.( SCGCQ01252186 ) 
 - Ventura 12G Links Occasionaslly Train Without SSC with Toshiba 12G SSD drives behind 6M cables( SCGCQ01252341 ) 
 - pl: task management may not complete with heavy IO load( SCGCQ01258861 ) 
 - VSES diag page 0A mapping not enabled for NVMe devices( SCGCQ01261033 ) 
 - Marlin: backend PCIe: various faults occur when a backend PCIe link goes down( SCGCQ01261195 ) 
 - Fault 0xD372 is seen during NVMe IO run and drive push pull test	( SCGCQ01271759 ) 
 - IOP: Incorrect temperature sensors polled( SCGCQ01280354 ) 
 - Modified default NVData to set the preset select to No Equalization for phys 8 - 15 to match phys 0 - 7.	( SCGCQ01295838 ) 
 - Ventura signed firmware image is crashing/abort stack( SCGCQ01304733 ) 
 - Due to a timing issue a hang condition may occur on cold power up( SCGCQ01311156 ) 
 - PD Lost observed, after system graceful reboot or Controller OCR	( SCGCQ01314168 ) 
 - Update host side spico to version 6069( SCGCQ01319764 ) 
 - PL Fault 0000d074 when run IOMeter overnight R0 fastpath	( SCGCQ01331410 ) 
 - Ventura: PL FW may Fault x61A5 during cable pull to an external enclosures with IOs outstanding	( SCGCQ01334254 ) 
 - Patrol read is too slow with IOs.( SCGCQ01341562 ) 
 - Ventura MSS: ECC errors encountered due to bad feedback compensation.( SCGCQ01354148 ) 
 - SSU Commands to SPL-2 compliant drive times out( SCGCQ01358769 ) 
 - NVMe: wrong reply type when Force Admin Error Response flag is set( SCGCQ01365133 ) 
 - PL: RETURNED LOGICAL BLOCK ADDRESS in READ CAPACITY (16	( SCGCQ01366977 ) 
 - pl: backend PCIe: EC79 fault	( SCGCQ01367013 ) 
 - PL: More than one ATA command at a time may be submitted to a SATA device( SCGCQ01377242 ) 
 - MR 7.4 - EPD non read write IO's need to be passed through to drives	( SCGCQ01377806 ) 
 - pl: NVMe: device initialization may not be retried on error( SCGCQ01380464 ) 
 - Fix the compiler warnings in plTbMgr.c( SCGCQ01385694 ) 
 - Fault 0xd074 while running IOs with Non-Auto commands & config page read( SCGCQ01388638 ) 
 - MR 7.4 - Missing profile 12 to support 240 PD/VD in RAID personality	( SCGCQ01389010 ) 
 - MR7.1: Shutdown command received from host" missed in tty log( SCGCQ01389941 ) 
 - Consolidate the HOST TM debug variables( SCGCQ01391601 ) 
 - Cannot set profile Id to PCIe on 9460-8i controller.	( SCGCQ01392208 ) 
 - MR-7.4-Pre-Alpha: R0, R1, R10 VDs built with HDDs failed to complete format operation on Windows 2016 x64( SCGCQ01392904 ) 
 - disableSAS allows SATA drives( SCGCQ01393528 ) 
 - Ventura : " SAS discovery error event " message not seen in Linux driver logs( SCGCQ01395698 ) 
 - MR7.1 -587: Flash write Failed with err code 5( SCGCQ01396383 ) 
 - pl: NVMe: E402 fault	( SCGCQ01397837 ) 
 - During large topology cable break testing. Task Managements may time out due to an accumulation of time starting these TMs for many devices( SCGCQ01398213 ) 
 - 7.4: Taskman.c while perform cable pull/push multipath on Crusader iMR (48 JBODs	( SCGCQ01399203 ) 
 - Ventura 7.4 JBOD Personality : Target ID exhausted due to incorrect GUID target ID reservations( SCGCQ01399523 ) 
 - pl: NVMe: back out SCGCQ01392812	( SCGCQ01399559 ) 
 - NVMe PD removal during recon triggered C0:Assertion failure in ../../raid/pd.c at line 7441: (ar != AR_INVALID( SCGCQ01402373 ) 
 - iMR 7.4 - iMR controller hit Exception mon_task while booting up to VMWare 6.5( SCGCQ01403486 ) 
 - Allow only the hot plugged drive to be configured as EPD.( SCGCQ01404316 ) 
 - MR 7.4 - OFU flashing led to FW in Exception Mon_task Loop( SCGCQ01406734 ) 
 - MR7.4: Assertion failure in ../../raid/ldCmd.c at line 1252: FALSE while booting up VMware ESXi host	( SCGCQ01407830 ) 
 - Ventura BST 7.4 PJBod==> Controller POST hang at 73%	( SCGCQ01415585 ) 
 - Bitmap targetIdsToDelete used to track LD deletion not cleared following PD removal in JBOD mode	( SCGCQ01417497 ) 
 - pl: NVMe: 6001 fault	( SCGCQ01418183 ) 
 - Drive missing on power cycle	( SCGCQ01421447 ) 
 - MR-7.4-PreAlpha: Cannot set controller to RAID profile ID 12 from RAID profile ID 10	( SCGCQ01422409 ) 
 - Lnexecpted LogSense events generated on RAID and JBOD modes every five minutes( SCGCQ01422969 ) 
 - MR 7.4 Revert change for SCGCQ01412718( SCGCQ01423804 ) 
 - Ventura: Misc tri-mode backplane mgmt detection fixes and Slot status update changes	( SCGCQ01428718 ) 
 - pl: NVMe: memory leak in Verify (10/12/16( SCGCQ01429659 ) 
 - storclif64.exe /c0 show all command fails with "command not supported" but actually dumps output.( SCGCQ01435765 ) 
 - File name capitalization doesn't match #include and fails when building with Linux( SCGCQ01439249 ) 
 - MR7.4 iMR complains of reached max VDs error with only 3 VDs configured	( SCGCQ01444063 ) 
 - 7.4Alpha: nvdata need to be fix for 9441-8i related to an OEM WorkStation( SCGCQ01444165 ) 
 - Ventura: NVMe Target: REPORT LUNS SCSI Command Failed With CC for Supported SELECT REPORT field Values 01h, 10h or 12h( SCGCQ01444725 ) 
 - Ventura: NVMe Target: When MODE SENSE Command Executed for all supported Modes Pages, TRACK SKEW FACTOR Set as 0x01( SCGCQ01444843 ) 
 - Correct MFI passthrough TM matching logic for Host TM.( SCGCQ01445939 ) 
 - [PL] 7.4-MR 9460-16i(8GB	( SCGCQ01447367 ) 
 - Get VDM Support command does not have VendorID and VendorAddInfo fields properly populated( SCGCQ01450475 ) 
 - vSES Target: Allocation Length less than 16 Bytes for REPORT LUNS Command is not Handled Properly( SCGCQ01451022 ) 
 - pl: NVMe: EC26 fault	( SCGCQ01451332 ) 
 - WG:LSA in JBOD mode supports creating VD with "Always WriteBack" write policy( SCGCQ01454233 ) 
 - LSA shows "actions successful" message when user creates new JBod with controller has at max number of configured VDs( SCGCQ01454360 ) 
 - OEM HII populates ld.params.numDrives with ZERO if PRL=0x11 and uneven span support is on.( SCGCQ01454740 ) 
 - ld.c::LdDcmd( SCGCQ01461856 ) 
 - MR 7.4 - Multipath FO led to KA mon_task	( SCGCQ01464983 ) 
 - Change CACHE_HEADER_VERSION from 13 to 11( SCGCQ01465054 ) 
 - MR 7.5_UNMAP: For JBOD in JBOD-mode,Unmap is enabled even though drive is not capable.( SCGCQ01465673 ) 
 - Add new nvram variable to handle 4GB to 8GB MR FW Migration( SCGCQ01467193 ) 
 - MR7.5: NVMe passthrough for Identfiy command is not working( SCGCQ01467354 ) 
 - MR 7.4 - I/O on EPD dropped while running multipath FO.	( SCGCQ01469889 ) 
 - FW change to make boot block compile with latest code( SCGCQ01471538 ) 
 - UNMAP on VDs getting disabled for switching personality( SCGCQ01472038 ) 
 - Firmware needs block certain user initiated operaations while it is in pending transition from one profile or personality to another	( SCGCQ01473242 ) 
 - Sending Unmap command to Medium Error LBA does not remove LDBBM entry( SCGCQ01474960 ) 
 - HW Workaround:PCE backpressures AXI writes when Reply FIFO is full( SCGCQ01475082 ) 
 - Remove TFM VPD related prints which are not relevant for Ventura.( SCGCQ01475234 ) 
 - Unmap is getting enabled in firmware on NVME drives,but actually not (sg_util says not enabled( SCGCQ01478538 ) 
 - MR7.3 & 7.4 With iMR Unconfigured NVMe drives become Unconfigured Bad When Converting Them to JBODs( SCGCQ01479017 ) 
 - Drive addition in OS takes longer time when Drives are connected with certain backplanes to the controller( SCGCQ01479406 ) 
 - MR 7.3.1 MixMode-SAS drives become 0KB once re-inserted( SCGCQ01479653 ) 
 - MR 7.5 : PI Drive become offline when create VD( SCGCQ01482723 ) 
 - (SATA Only( SCGCQ01485060 ) 
 - FIQ and TaskAdd( SCGCQ01487394 ) 
 - MR7.5: Assertion failure in ../../dm/mpt2/mptTaskMgmt.c at line 1070: pDevInfo->devHandle[path] == devH( SCGCQ01491185 ) 
	Page 8 / 391
 - Ventura BST 7.5 iMr ==> Update to ROP 872 kill adapter( SCGCQ01495902 ) 
 - MR7.5: NVMe VDs import as JBOD after remove and re-insert( SCGCQ01496893 ) 
 - System will pop up “Cannot communicate with iButton to …” during reboot with OEM custom card	( SCGCQ01501209 ) 
 - Assertion failure in ../../dm/mpt2/mptframe.c at line 1250: mptIo!=NULL	( SCGCQ01502102 ) 
 - SATA: Report Zone for very large data of 4MB takes ~2 seconds for processing	( SCGCQ01502700 ) 
 - MR-7.5-Alpha: Cannot set Foreign UBad to Foreign UGood with a config of 31 VDs and iMR 9441-8i( SCGCQ01505522 ) 
 - SAS3.5FW_Common_Main was not stable after merging code changes for SCGCQ01421231	( SCGCQ01508018 ) 
 - MR 7.5-MR 9460-16i:Hit Assertion failure in ../../cpu/arm/exceptions.c at line 938 During I/O & Multipath Cable Pull	( SCGCQ01508249 ) 
 - MR7.5: Assertion failure in ../../cpu/arm/exceptions.c at line 938 observed, while destaging preserved cache on R0 DG( SCGCQ01509791 ) 
 - When update Vendor SAS 2.5" 10K 12Gbps 300GB HHD (PN:SH20J34185( SCGCQ01515259 ) 
 - Dump pending driver IO completions from task context during kill adapter debug( SCGCQ01519710 ) 
 - Ventura: 4311 fault with NVMe enabled( SCGCQ01519732 ) 
 - MR7.5: Firmware asserted at memory.h at line 443: isInAddressibleRange when push/pull JBOD NVMe drives( SCGCQ01522362 ) 
 - MR7.5: Firmware reports iopiTimedOutIOFound when running IO on NVMe JBOD drives	( SCGCQ01522509 ) 
 - 75Beta: pk970 Kill Adapter when create vd( SCGCQ01531146 ) 
 - MR 7.5: Enable MR code for generating firmware not compatible with profile event	( SCGCQ01538991 ) 
 - MR7.5 Beta OEM name Characters seen in HII Drive management instead of port information.	( SCGCQ01563926 ) 
 - MR7.5: Rearrange MR IO path routines to fit the new PL( SCGCQ01565754 ) 
 - MR7.5: Changing personality between RAID and JBOD resulted in firmware assertion	( SCGCQ01566825 ) 
 - Task Management due to SATA init failure results in resource error message( SCGCQ01605610 ) 
 - DISM - Assertion failure in ../../dm/src/devRemoval.c for breaking multipath during bootup( SCGCQ01618628 ) 
 - [MR7.5] Rebuild Progress 0 % logged just after OS reboot during rebuild running	( SCGCQ01631496 ) 
 - Not to do all drives reset at the start of the boot up on each port of the controller( SCGCQ01670965 ) 
 - incrementing other error count for RECOVERED_ERROR with any asc and asc apart from 00/1d	( SCGCQ01729713 ) 
 - MPI2_FW_IMAGE_HEADER is 16 bits too long	( SCGCQ00009501 ) 
 - Firmware download fails with lsiutil but works with sas2flash( SCGCQ00141277 ) 
 - Moved Uartsettings from page 11 to page 31( SCGCQ00142367 ) 
 - (IOP-Only( SCGCQ00142963 ) 
 - Device add/remove testing results in a fault 0x6202.	( SCGCQ00151026 ) 
 - When devices are removed / added the I/Os hang.( SCGCQ00151027 ) 
 - High Priority message queue messages would fail( SCGCQ00151447 ) 
 - 0x6700 Fault	( SCGCQ00156772 ) 
 - Invader FW hangs when booted from FLASH	( SCGCQ00158076 ) 
 - (FPGA-Only( SCGCQ00160356 ) 
 - Fault 265D occurs following Port Enable when IR FW is loaded	( SCGCQ00162600 ) 
 - Fault 0xd012 while using Cuda timer when timeout is set to less than 3 seconds( SCGCQ00165753 ) 
 - Local chaining causes SAS core fetch errors	( SCGCQ00170855 ) 
 - FPGA: 0x5111 fault during Target Mode testing( SCGCQ00172991 ) 
 - Bugs found in DDR3 library during Palladium testing( SCGCQ00175814 ) 
 - 6001 Fault During IR RAID0 Volume Creation Under Linux SLES11( SCGCQ00177106 ) 
 - Code is modified such that temperature sensor channel defines now match the actual sensor placements in Invader Silicon.	( SCGCQ00186585 ) 
 - Firmware heap memory corruption( SCGCQ00192923 ) 
 - Implement workaround for PPC476 errata( SCGCQ00194226 ) 
 - Invader A0: Writing to Ethernet Page 1 current fails/hangs( SCGCQ00194767 ) 
 - Inaccurate firmware delay causes 0x670B fault( SCGCQ00195374 ) 
 - (FPGA Only( SCGCQ00200505 ) 
 - Ethernet is unresponsive during fault( SCGCQ00202278 ) 
 - Fault 0x5805 when running very heavy FPE IO	( SCGCQ00205679 ) 
 - ITRACE dump command fails with memory allocation error.( SCGCQ00208393 ) 
 - Undefined macro IOP_MEM_REGION_TYPE_DDR_CACHED_SECOND_RANK in IOP( SCGCQ00213011 ) 
 - Invader A0: Fault 265D while running Block Move and Task Management Test	( SCGCQ00217049 ) 
 - Invalid 0x5897 and 0x6828 faults	( SCGCQ00218792 ) 
 - 0x5841 while doing single Phy cable breaks for 1 second( SCGCQ00219298 ) 
 - Invader A0 (USB	( SCGCQ00219373 ) 
 - Compilation issue on USB code( SCGCQ00219383 ) 
 - PCI-Express defect requires faster firmware response	( SCGCQ00223692 ) 
 - SAS3: 0x265D Fault while disabling Fast Path.( SCGCQ00229247 ) 
 - Firmware gets reset when we add Hot Spare to the Raid 1 volume.( SCGCQ00229913 ) 
 - PL: Need to have unique fault codes	( SCGCQ00263726 ) 
 - NVData: Update B0 SBR settings and other miscellaneous updates( SCGCQ00270288 ) 
 - (IOP	( SCGCQ00271154 ) 
 - IOP: IO Timeouts occur after running for 9.5 hours( SCGCQ00279186 ) 
 - Performance monitor for the COLT Core are not working.( SCGCQ00284994 ) 
 - IOP: Firmware fails to build	( SCGCQ00292957 ) 
 - Foreign volume activates and starts rebuilding( SCGCQ00310543 ) 
 - BGI disabled for PI volume when CC_Disable is set( SCGCQ00314979 ) 
 - An internal tool for parsing stack traces needed an update( SCGCQ00349338 ) 
 - Enable the new PCIe device translation block	( SCGCQ00349889 ) 
 - (CUDA( SCGCQ00386306 ) 
 - PCIE IO Unit 0/1 size in header is not correct	( SCGCQ00394558 ) 
 - Internal tool change. No change to firmware.	( SCGCQ00394559 ) 
 - Several issues related to exception/error handling for NVMe devices( SCGCQ00397632 ) 
 - Typo in SAS3 hardware header file( SCGCQ00398334 ) 
 - Dauntless FPGA: Data Corruption reported when running 1M IO to AHCI device( SCGCQ00424263 ) 
 - No access to DDR for backend PCIe devices( SCGCQ00426529 ) 
 - FPGA timers are longer than expected.( SCGCQ00432537 ) 
 - AHCI: Command timeout with mixed auto and nonauto IOs( SCGCQ00448191 ) 
 - Dauntless FPGA PDB PIM alignment issue( SCGCQ00449934 ) 
 - IOP: Maximum Stang exceptions handled count is too high( SCGCQ00521714 ) 
 - NVMe: Write Buffer (mode 0x5	( SCGCQ00557073 ) 
 - Dauntless: Backend POM Window size should be aligned to number of PCIe devices supported	( SCGCQ00558089 ) 
 - Remove Palladium NVDATA for Dauntless.( SCGCQ00602338 ) 
 - Dauntless SPI DCR setting( SCGCQ00612654 ) 
 - SAS3.5 MCTP: Bit field changed in I2CSlave( SCGCQ00638812 ) 
 - Accessing unmapped memory space for undefined SGPIO registers results in L2 errors.( SCGCQ00680988 ) 
 - NVData: Update MfgPg 9 minimum values to meet requirements( SCGCQ00740652 ) 
 - Ventura: SPI Library doesn't work with CFGI	( SCGCQ00741845 ) 
 - Ventura: Build Error - Code is non-compliant with the latest CPP standard( SCGCQ00811305 ) 
 - Ventura: System hangs when fault occurs	( SCGCQ00814903 ) 
 - Description for each PL_ASSERT fault is Required	( SCGCQ00816653 ) 
 - Ventura: Backtrace logic loops forever when no SYMBINFO structure is attached( SCGCQ00824296 ) 
 - Ventura: MSIX offsets incorrect in capability( SCGCQ00853678 ) 
 - NVDATA: SAS9305-16e board does not link up( SCGCQ00855042 ) 
 - Ventura: core level interrupt starvation (part 3	( SCGCQ00855861 ) 
 - CommonSerdes Library compliance test fails( SCGCQ00864339 ) 
 - PL initializes IOA Local RAM with 0s without IOP FW knowing	( SCGCQ00877473 ) 
 - Ventura: IOC Capabilities needs Atomic Descriptor bit set( SCGCQ00892729 ) 
 - BL: Fix compiler warning about bad constant expression( SCGCQ00901269 ) 
 - BL: Tiger bootloader is locking up and causing aborts( SCGCQ00910746 ) 
 - RBD tool is not included in normal releases, so release notes are not required.( SCGCQ00910886 ) 
 - Build: Build all script fails( SCGCQ00914091 ) 
 - Build all fails in common main due to missing RmcSbr.bin file( SCGCQ00914418 ) 
 - NVData: Change to using 256 byte message frames	( SCGCQ00927945 ) 
 - Spi Library does not work with PCI windows( SCGCQ00949953 ) 
 - Move CSW Tx Phase Slip Workaround to the ComboSerdes Library	( SCGCQ00951761 ) 
 - Ventura IT: uploading of image is failing with 265D( SCGCQ00952523 ) 
 - Tiger: CSW library build error due to incorrect path	( SCGCQ00982299 ) 
 - Ventura A0: Fault 0xD20D during shutdown of linux system	( SCGCQ00992057 ) 
 - Ventura: Build ALL failure( SCGCQ00997110 ) 
 - Tiger: Allow FPGA Build to Work on Veloce Platform( SCGCQ01000130 ) 
 - Tiger: Clean Up Code in PCIe High Priority Interrupt Handler	( SCGCQ01002423 ) 
 - Ventura A0: Debug masks set in uart are not being honored( SCGCQ01017063 ) 
 - Ventura: host system crashes on hard reset after firmware update	( SCGCQ01019234 ) 
 - IOP: Reply descriptors not being sent to the host( SCGCQ01024830 ) 
 - Ventura MSS: DDR library completes successfully but memory access results in data corruption	( SCGCQ01034012 ) 
 - Ventura: Firmware Path Peformance is Low Compared to Cutlass	( SCGCQ01036330 ) 
 - Ventura A0: NVMe device isn’t getting reconfigured even though discovery runs and appears to find it	( SCGCQ01058974 ) 
 - Ventura MSS: Interface changes for dual rank	( SCGCQ01070444 ) 
 - Marlin: Enabling PVT at conclusion of DDR init causes data corruption issues.( SCGCQ01070542 ) 
 - Fault x6030 seen running Abort Task	( SCGCQ01080071 ) 
 - Marlin A0: During PCIe jammer testing, host system reboots after just a few seconds due to completion timeout( SCGCQ01080162 ) 
 - Coverity defect: Dereference after null check and Unused value( SCGCQ01089963 ) 
 - ComboSerdes: The SAS 12G Preset selection is fixed to NO-EQ	( SCGCQ01089992 ) 
 - Coverity defect: Out of bound memory access	( SCGCQ01093405 ) 
 - Tiger FPGA: Fix PCIe Io Unit Page 0 Read handler	( SCGCQ01095060 ) 
 - Ventura A0: TFM Fixed information being reported, but is all bogus values( SCGCQ01118873 ) 
 - Ventura MSS: flawed conditional expression checking for ECC errors( SCGCQ01119518 ) 
 - Marlin MSS: Half mode does not work( SCGCQ01133813 ) 
 - IOP: MCTP: PCIe Message transmission hardware can send extra DWORD and split packets	( SCGCQ01146557 ) 
 - Ventura/Marlin A.0: Firmware faults 0x1500, reply parity error( SCGCQ01154820 ) 
 - Need to support different bus address values for PMBus voltage regulators.( SCGCQ01174484 ) 
 - Ventura PL: (NVMe( SCGCQ01196103 ) 
 - Ventura RMC: Improvements to AHR reset sequence to avoid Credit overflow issue seen in simulation.( SCGCQ01264665 ) 
 - Ventura/Marlin: 265D fault sometimes occurs when diag console utility is in use( SCGCQ01264675 ) 
 - Second rank showing different VREF results from first rank.( SCGCQ01267430 ) 
 - Ventura: Uart RX fifo uses an extra byte	( SCGCQ01293446 ) 
 - Ventura: HVD6 SERDES 3G/6G Attenuation Settings and Rx settings( SCGCQ01296832 ) 
 - One Spico load failure causes all subsequent Spico processors to be left at reset.( SCGCQ01302306 ) 
 - Can't program SPDimage to SPD EEPROM	( SCGCQ01314177 ) 
 - Ventura B0: CPLD flashing fails on 94008i8e	( SCGCQ01319974 ) 
 - Ventura/Marlin: backend PCIe: IO halt after a link glitch( SCGCQ01336859 ) 
 - Failure to read correct data from SPD EEPROM	( SCGCQ01358941 ) 
 - Clean up for Blackduck( SCGCQ01377109 ) 
 - pl: NVMe: E40E fault	( SCGCQ01377681 ) 
 - Ventura B0: NVME Drives Not Discovered on 16i Card( SCGCQ01381033 ) 
 - Ventura 7.4 - Enable FP reads and writes across stripe for single drive R0 WT LDs( SCGCQ01381722 ) 
 - storclif64 7.401.0.0: vall shows no VDs in JBOD mode while drives connected	( SCGCQ01384995 ) 
 - Controller issues 'BREAK' if expander returns 'OPEN_REJECT(RETRY	( SCGCQ01387414 ) 
 - MR7.4 Talladega 16i - RAID mode: Device ID changed after FW upgrade from MR7.2 to MR7.4( SCGCQ01387454 ) 
 - Unexpected IOC errors from PL( SCGCQ01389558 ) 
 - Task Abort fix and some framework for task abort check in.( SCGCQ01389705 ) 
 - Ventura/Marlin: SPI Library status irregularities( SCGCQ01393626 ) 
 - MR 7.4 - Missing inserted PDs (237 out of 239( SCGCQ01399538 ) 
 - MR_FW: Incorrect Block Limits VPD page for RAID Volumes	( SCGCQ01399941 ) 
 - DEVICE_INFO.hostTmActive flag not cleared for Abort task when the abortId is found in the DevWaitQ( SCGCQ01402362 ) 
 - MR 7.4 - FW hangs @ POST, RAID BIOS reported "A discovery error has occured".. even after power off/on a whole setup/encls.( SCGCQ01402855 ) 
 - Fix static code analysis tool detected defects( SCGCQ01406220 ) 
 - MR 7.4 when perform TaskMgmt on pd hit Assertion failure in ../../cpu/arm/exceptions.c at line 938: 0( SCGCQ01409019 ) 
 - Ventura: NVMe Target: Non-Zero Value in TRACK SKEW FACTOR field of FORMAT DEVICE Mode Page( SCGCQ01412908 ) 
 - Moving MFI state from undefined (0( SCGCQ01413748 ) 
 - Controller hangs after updating to latest ROP 676( SCGCQ01422235 ) 
 - MR 7.4: PL Fault 0000d033 LR 7f86e947 observed in JBOD personality (profile 23( SCGCQ01427119 ) 
 - Add SAS device discovery error event to IOP message events.( SCGCQ01428178 ) 
 - MR7.4 Crusader foreign import VDs hit assertion failure	( SCGCQ01438085 ) 
 - : MR 7.4 : Incorrect size (ZB( SCGCQ01438165 ) 
 - Add Debug for SED pass through( SCGCQ01440446 ) 
 - MR7.4: EPDs do not convert to JBOD when changing controller personality from JBOD to RAID.( SCGCQ01441340 ) 
 - FW crash	( SCGCQ01444114 ) 
 - extraneous assert on breaching MAX DEV/ENCL in profile.c::ProfileHandleTopologyErr( SCGCQ01447270 ) 
 - EPD data loss	( SCGCQ01449349 ) 
 - Revert autochain pull enablement for iMR	( SCGCQ01455832 ) 
 - XSD update requires major version change.( SCGCQ01455916 ) 
 - Ventura: Break up backplane mgmt device ISTWI Read/Write to the supported size( SCGCQ01456349 ) 
 - MR 7.4 iMR Crusader after IO and cable pull push from storclif command see Enclosure 64 but cannot find the enclosure 64	( SCGCQ01467123 ) 
 - Optimize abort handling in command block context.( SCGCQ01467284 ) 
 - Ventura MR - RAID Personality - R0 WB SW 4/8K all QD regression RHEL	( SCGCQ01468157 ) 
 - Clean up static code analysis tool detected defects	( SCGCQ01470671 ) 
 - pl: NVMe: port enable may complete before devices link up( SCGCQ01472531 ) 
 - Block personality change when EPD security is not safestore managed.	( SCGCQ01473960 ) 
 - Update OOB_METHOD_INFO_NVRAM due to changes in NVRAM	( SCGCQ01475424 ) 
 - Ventura vSES: Direct attached NVME drives are not getting associated with vSES in Microsoft Storage Spaces Direct.( SCGCQ01478170 ) 
 - Compile fix for mis-typed constant( SCGCQ01478391 ) 
 - FW does not complete if a bad drive return medium error for a pre-read(SCGCQ01481035 ) 
 - MR7.3.1_Assertion failure in ../../dma/dmaxor.c at line 1180:( SCGCQ01482384 ) 
 - MR7.5 : Not able to boot to OS with iMR NVMe	( SCGCQ01482722 ) 
 - MR7.5pkg846: Found IOs drop while multipath cable pull/push on maxconfig 230 Jbods( SCGCQ01484297 ) 
 - Intel MR7.3 & MR7.4 Beta: RAID-5 Hardware Key No Longer Functional with Intel Lava Dunes (ROP 834 & earlier is okay( SCGCQ01484398 ) 
 - MR 7.5 : iMR controller breaks into monstak if connect to SAS/SATA enclosure with NVMe profile	( SCGCQ01487399 ) 
 - 30% to 35% JetstressDB Average Write Latency regression found in R5, MR 7.4 Beta	( SCGCQ01488410 ) 
 - MR 7.5-iMR 9440-8i: Hit Assertion failure in ../../hw/pce/fusion.c at line 1847 after loading the driver & reboot( SCGCQ01502112 ) 
 - erroneously sorting bvdInfo while retrieving DDF Config causes DDF to be corrupted( SCGCQ01503916 ) 
 - pl: backend PCIe: additional phy hardware cleanup on link down and hot reset	( SCGCQ01504284 ) 
 - fw got data abort when connect more enclosure than max in iMR.( SCGCQ01509463 ) 
 - MR7.3.1 : user can set unsupported controller profile (ID: 12( SCGCQ01509952 ) 
 - pdCOD content is being overwritten when using storelibtest to issue SCAN FOREIGN	( SCGCQ01518446 ) 
 - Merge issue while removing unmap code from 7.5( SCGCQ01522805 ) 
 - MR 7.5_LSA: All VDs are not getting deleted after the vd erase operation with 'delete VD after erase' option is selected	( SCGCQ01522814 ) 
 - MR7.5: Spin up large config drives by load the config file while they are in POWERSAVE, caused FW hit DrvSpinup.c @line 1362	( SCGCQ01529400 ) 
 - Smart Return Status passthru command failed on SATA drives	( SCGCQ01555033 ) 
 - Data loss while upgrading from MR7.3 to MR7.5 because of cache start address change( SCGCQ01562381 ) 
 - : FW asserts when invalid parameters to set excluded ld for CC is sent to firmware.( SCGCQ01635729 ) 
 - Purely Server: Firmware Not Logging to Flash or Can't be Uploaded with StorCLI( SCGCQ01639777 ) 
 - MR PD GET info fails for SES processor( SCGCQ01685797 ) 
 - FPGA : FPE FW - Add a non zero value to Max completion Queue Read Count( SCGCQ00143659 ) 
 - FPGA: Bugs in TBM code( SCGCQ00143878 ) 
 - IOs stop suddenly with Open Reject No Destination( SCGCQ00152325 ) 
 - Fault 0x5861 on sending read IO from UART( SCGCQ00160923 ) 
 - Fault 0xD071 seen when sending down Abort Task Task Management(s	( SCGCQ00169004 ) 
 - TM: Fault 0xD0ED while running task management( SCGCQ00179989 ) 
 - Config Space VPD Read Incorrect( SCGCQ00183686 ) 
 - Fix 2 unguarded loops in Control Queue Cleanup( SCGCQ00183881 ) 
 - Ethernet: Checking Ethernet Page 0 with no MAC/SAS Address causes 0x265D fault( SCGCQ00195119 ) 
 - Linux driver fails to load on systems with more than 8 processor cores( SCGCQ00197603 ) 
 - Timeout of an Inquiry command to SATA drive which was already completed as failure	( SCGCQ00199797 ) 
 - Fix to accomodate backward compatibility for drives >2TB with Gen1	( SCGCQ00206467 ) 
 - PPC timebase register is not being read correctly in iopiGetTimeSinceStartOfDayUsec	( SCGCQ00208443 ) 
 - Invader internal memory corruption causes IOs to fail( SCGCQ00215887 ) 
 - Invader A0: IO print filtering optimization is not accounting for firmware subsystems( SCGCQ00223648 ) 
 - IOP: Enabled the early power loss interrupt( SCGCQ00277815 ) 
 - Invader: Fixed Build Problem Due to Mistake in NVDATA( SCGCQ00328068 ) 
 - No interrupt handler for L2 interrupts( SCGCQ00349336 ) 
 - Need Proper Routine for Initializing Cuda Timer Wheel RAM (Reset Sequence( SCGCQ00403591 ) 
 - Extra validation required for Silverhawk PIM1 settings( SCGCQ00484633 ) 
 - Backend PCIe completion timeout after a PCIe error message is received( SCGCQ00498112 ) 
 - Tip code fails to boot on Dauntless FPGA	( SCGCQ00628332 ) 
 - PLI_NVME_PRP_ENTRY contains U64math	( SCGCQ00665096 ) 
 - Ventura: ARM mmuVirtualToPhysical returns 1 instead of 0xFFFFFFFF for failure( SCGCQ00790198 ) 
 - SAS3.5 Hitting fault 0x265E at start of day	( SCGCQ00811690 ) 
 - Intruder A0: Ring buffer hangs up the UART and needs to reboot the server.( SCGCQ00845742 ) 
 - Ventrua FPGA: hit Fault 0x5801 running Data Integrity from RedEye( SCGCQ00857273 ) 
 - Ventura: Update the PCE SBR for device IDs other than 0xAA( SCGCQ00991202 ) 
 - BL: Tiger encounters fault 0x265D during boot( SCGCQ01045711 ) 
 - Marlin A0: HBA goes to hung state while sending diag reset( SCGCQ01084604 ) 
 - Unused return value of flash write function	( SCGCQ01091183 ) 
 - Ventura: bldnvme.bat is still referencing raw.fw	( SCGCQ01183481 ) 
 - NVDATA config option to disable PL Virtual SES support( SCGCQ01251655 ) 
 - Code Review Defect for Code collab Id 6005( SCGCQ01343128 ) 
 - Incorrect Component ID definitions of CubR 35x24 and 35x28( SCGCQ01350510 ) 
 - Make Ventura UART work at 460800	( SCGCQ01367233 ) 
 - Jetstress Performance Regression with RAID10 and Single Driver R0( SCGCQ01381091 ) 
 - Code review AI( SCGCQ01382101 ) 
 - Disable all error recoveries on EPD-PT for host IO's	( SCGCQ01389003 ) 
 - Host TM test framework fixes and adding the hostTM escalation framework( SCGCQ01389352 ) 
 - Handle timeout recovery for FPIO's in JBOD personality( SCGCQ01394886 ) 
 - MR 7.4 8G - RAID to JBOD personality after Cn caused "Assertion failure in ../../cfg/cfgisup.c at line 3783: wIndex==0"( SCGCQ01403998 ) 
 - Need to prevent conflicts between jbod mode, and jbod personality.( SCGCQ01405517 ) 
 - Remove IntNesting inc & dec from TimerISR as it is duplicate.( SCGCQ01406721 ) 
 - MR7.4: LDs disappear when changing controller profile (from profile 10 back to profile 12( SCGCQ01413560 ) 
 - IMR 7.4 : Kill adapter during cable push/pull( SCGCQ01420821 ) 
 - Unable to change personality	( SCGCQ01421114 ) 
 -	( SCGCQ01441140 ) 
 - 9460-8i card connect drive through direct-attached backplane: error LED not on when drop out a drive.( SCGCQ01445040 ) 
 - FW hit killer adapter while I/O and Jammer running( SCGCQ01445237 ) 
 - Single Thread MSI-X and MCTP accesses( SCGCQ01446273 ) 
 - MR74 iMR Assertion failure in ../../raid/cache.c at line 4461( SCGCQ01447442 ) 
 - BCA Cable Detection / Port Mapping Issue	( SCGCQ01448400 ) 
 - vSES Target: Incorrect Sense Data for REQUEST SENSE Command( SCGCQ01451678 ) 
 - [PL]74Alpha: Crusader iMR multipath cable pull/push hit taskman line 342 on 48 JBODs	( SCGCQ01452339 ) 
 - Ventura MR - MR 7.4 not discovering NVMe devices	( SCGCQ01453903 ) 
 - MR 7.4 - PDs pull/push led to "PD INSERT DEFERRED.. PD REMOVAL of PD X in PROGRESS" KA mon_task	( SCGCQ01454152 ) 
 - WG:Pausing progress operation and resuming shows it starting from 0 again and abruptly moves to actual progress after a while( SCGCQ01454613 ) 
 - MR7.4 MonTask: line 120 in file ../../raid/utils.c rst=1 When Starting CC after double media error injection to 2 NVMe drives( SCGCQ01454617 ) 
 - pl: backend PCIe: erroneous address pool copy( SCGCQ01455651 ) 
 - Debug Levels in unmap code path	( SCGCQ01455974 ) 
 - [PL]MR 7.4 imr IO on JBOD and VDs then cable pull push see some IO stop as found VDs offline	( SCGCQ01464997 ) 
 - Move resetTypeFromCCR to NVRAM for access during SOD.( SCGCQ01467122 ) 
 - pl: NVMe: 6001 fault	( SCGCQ01468144 ) 
 - 930-16i Cannot Spinup HDD During System Power On	( SCGCQ01470741 ) 
 - SATL: Security Protocol Erase fails in SATL, but works well with ATA PT.	( SCGCQ01479409 ) 
 - MR: Loading SBR with OFU causes system hang	( SCGCQ01479700 ) 
 - pl: NVMe: task management timeout may occur	( SCGCQ01480646 ) 
 - pl: NVMe: switch attached devices not detected under Windows	( SCGCQ01487291 ) 
 - passCount not incremented for Ctlr Self Diag Link Test( SCGCQ01505906 ) 
 - web UI is exposing personality change option for iMR controller( SCGCQ01512359 ) 
 - 7.5 iMR IO false divert due to SlotCount.( SCGCQ01514114 ) 
 - MR7.5: Firmware hit exception handler when clearing config or delete VD using nvme on 9440-16i( SCGCQ01518347 ) 
 - Win/Lin MR 7.5 Alpha/Beta R0,1,5,6; 5%-9% is seen in SR,SW IOs-4K-32K,QDs (1,4,16,64	( SCGCQ01538207 ) 
 - Change CmdIgnoreLdUnitAttention(	( SCGCQ01545274 ) 
 - I2C bus disable bit is not set when nvdata requests to disable( SCGCQ00139235 ) 
 - plFpeiAddIOTimer needs to use a unique fault code in its call to PL_VALIDATE_MID. This is provide support for faster debug from customer site.( SCGCQ00170054 ) 
 - IOP CLI command iop show tlb displays incorrectly( SCGCQ00173993 ) 
 - Fix for updating PCIe speeds in config page IO UNIT PAGE 7.	( SCGCQ00193001 ) 
 - Incorrect PCI Sub-class Code Causes Failure During Windows WHQL Testing( SCGCQ00203666 ) 
 - Update PLB Snooping config for SASCore to set bit11 instead of bit 8 for config bits.( SCGCQ00257436 ) 
 - (IOP	( SCGCQ00382561 ) 
 - Incorrect default setting for LinkFlags field for PCIe phy in PCIe IO Unit Page 1 Configuration Page	( SCGCQ00589097 ) 
 - Ventura: iopiMemoryMove shouldn't call pliControlRequest to get host page size every time.( SCGCQ00712297 ) 
 - Make _PLI_PCI_ADDRESS_POOL_ELEMENT a multiple of 8 bytes in size	( SCGCQ00853335 ) 
 - IOP: Build fails with missing define in GPIO code( SCGCQ00914704 ) 
 - Aero build fails due to out of date Nvdata file.	( SCGCQ01122630 ) 
 - RMC: Handling of PLL reset does not meet timing specified in PLL datasheet.( SCGCQ01319599 ) 
 - Fix the prodIdentification( SCGCQ01374781 ) 
 - RAID VDs become foreign following more than one reboot( SCGCQ01386126 ) 
 - Disable fast path when Unit Attention is active on the EPD-PT( SCGCQ01389657 ) 
 - pl: NVMe: additional errors occur after NVMe init failure( SCGCQ01392157 ) 
 - MR-7.4 PA2: Extra disk reported in Disk Manager( SCGCQ01392353 ) 
 - pdRef filled incorrectly in bvd->Physical_Disk_Sequence[] causing DDF to skip added PD in Recon( SCGCQ01400343 ) 
 - MR-7.4-PreAlpha: Without any config cannot set ctlr to RAID from JBOD personality on Windows 2012 R2	( SCGCQ01404419 ) 
 - Dev testing defects from Storcli.( SCGCQ01405201 ) 
 - MR7.4 PA2 Talla16i ROP 621: KA on target reset( SCGCQ01408002 ) 
 - Unable to set security Key( SCGCQ01410223 ) 
 - 7.4 Profile Switch behavior with respect to WB volume( SCGCQ01413375 ) 
 - 7.4:240pds JBOD-mode: create/delete config hit raidpci.c line 2550( SCGCQ01423692 ) 
 - MR 7.4 BST : Drives become UBAD when reboot server or OCR with BST setup : Personality mode with Profile 23( SCGCQ01434065 ) 
 - MR 7.4 - FW hit KA while IOing( SCGCQ01442985 ) 
 - Add a check to port NVRAM changes related to upgrade/downgrade issue	( SCGCQ01473175 ) 
 - MegaRAID with MCTP PCIe VDM not able to be rediscovered by BMC Emulator's MCTP service( SCGCQ01473240 ) 
 - MR7.5: FW hit assertion failure when booting up with enclosure attached( SCGCQ01507024 ) 
 - Fix Temperature Throttling in Ventura( SCGCQ01510251 ) 
 - MR7.3.1 : iMR FW locks up and PSOD seen while trying to flash MR7.2.1 FW ROP	( SCGCQ01516986 ) 
 - (MEMCFG only	( SCGCQ00138834 ) 
 - I2C slave address is only assigned to bus 0 and 2( SCGCQ00139212 ) 
 - Invader A0: The controller is reset when a MPT power management global change request is issued.( SCGCQ00212977 ) 
 - Fix issues encountered while unit testing non read write native SGL handling	( SCGCQ00468465 ) 
 - pl: Unbounded wait in plPhyClearErrorRegisters() SCGCQ00768573 ) 
 - Structures not packed due to U64 type definations being different( SCGCQ00853897 ) 
 - IOP: Fix build errors( SCGCQ00862262 ) 
 - Address performance issue for CPU intensive profiles.( SCGCQ01522492 ) 
 - Patrol read progress pause when user try to change profile( SCGCQ01614870 ) 
 - Drives are reverted back to JBOD after perfoming instant secure erase( SCGCQ01615777 ) 
 - Fix personalityChangeReqPending for an OCR case	( SCGCQ01384904 ) 
 - Fix for FW keeps reporting missing config in JBOD mode after switching from RAID mode and Clear Config( SCGCQ01386114 ) 
 - Add MrParamPage1 and test MrParamPage1.( SCGCQ01394514 ) 
 - Enable Security on EPDs	( SCGCQ01398337 ) 
 - EPDs secured by SafeSTOR and 3rd Party tool( SCGCQ01399100 ) 
 -	( SCGCQ01464221 ) 
 - FW does not respond to MCTP packets when BIOS is disabled (BMC emulator( SCGCQ01473945 ) 
 - address merge conflict from 73rc to 73lenovo	( SCGCQ01499771 ) 
 - Auto rebuild does not start when HS has PF( SCGCQ01509537 ) 
 - [OOB]RMC/MR Crash Due to PCE Core Register Access Errata during vSAN certification Test( SCGCQ01521255 ) 
 - NVDATA for iMR has maxChainedEnclosures set to 10; should be set to 2( SCGCQ01598760 ) 
 - After FW update, controller was not reset by the OCR command, and if user retries the command, then FW hits the exception( SCGCQ01639394 ) 
 - Not able to set max no of PD using set patrol read properties in LSA/Storcli	( SCGCQ01671189 ) 
 - Too many Unexpected Sense : "1/0/1d " logged for SATA drives	( SCGCQ01714261 ) 
 -	( SCGCQ01417586 ) 
 - MR_7.3.1_Firmware hangs in discovery	( SCGCQ01484421 ) 
 - LAS does not show proper state of secured locked drives.	( SCGCQ01615781 ) 
 - IR: Fast resync turned off when pulling a path in a multipath system	( SCGCQ00136963 port of SCGCQ00127015 ) 
 - 8618 fault is hit with ph-6 firmware during volume rebuilding( SCGCQ00138307 port of SCGCQ00138131 ) 
 - Add 64-bit multiplication, division, and modulus functions to PL	( SCGCQ00138469 port of SCGCQ00138467) 
 - Add 64-bit multiplication, division, and modulus functions to PL	( SCGCQ00138470 port of SCGCQ00138467) 
 - (RMTFLASH only	( SCGCQ00141237 port of SCGCQ00141235) 
 - IR MP: Fault 8405 encountered if resyncing disks is removed.	( SCGCQ00141639  port of SCGCQ00140613) 
 - False Warning device type message if SATA and SAS VDs co-exist( SCGCQ00142463 port of SCGCQ00083799) 
 - IOP: Diagnostic Console xget commands fixed	( SCGCQ00149248 port of SCGCQ00146562) 
 - Typo in SATA init code could result in wrong block size reported for non-512 SATA drives	( SCGCQ00150247 port of SCGCQ00146128) 
 - Removing dead code for volume inline update	( SCGCQ00150518 port of SCGCQ00145728) 
 - Flashing a thunder bolt or meteor with DDR enabled FW cause a 1808 fault followed by a recursive 265d fault	( SCGCQ00151261 port of SCGCQ00143378) 
 - UART console does not show 8k-bit SBR correctly	( SCGCQ00153299 port of SCGCQ00147843) 
 - (IOP-Only	( SCGCQ00153306 port of SCGCQ00144646) 
 - pl: SATL: Support write buffer mode 7.	( SCGCQ00153476 port of SCGCQ00148567) 
 - IR: (IR only	( SCGCQ00153683 port of SCGCQ00125128) 
 - Support exiting self-refresh mode in DDR3 library, for battery backed implementations( SCGCQ00153708 port of SCGCQ00151472) 
 - Customer requested change to DCR requirement placed on IOP by DDR3 library( SCGCQ00153709 port of SCGCQ00147761) 
 - Thunderbolt SysDma fails to read or write DDR3	( SCGCQ00153725 port of SCGCQ00145561) 
 - IOP: Change Start of Day memory allocation for Raid Accelerator request queues( SCGCQ00153763 port of SCGCQ00102813) 
 - IOP: DNS lookup feature in Ethernet Firmware Download does not handle errors properly( SCGCQ00153866 port of SCGCQ00141822) 
 - Ethernet: Unable to open new Telnet session after closing 3 simultaneous Telnet sessions	( SCGCQ00154723 port of SCGCQ00148547) 
 - Method to prevent drivers from resetting firmware during large CLI command	( SCGCQ00154736 port of SCGCQ00147885) 
 - Ethernet: Exiting Telnet sessions may cause firmware fault	( SCGCQ00154855 port of SCGCQ00149405) 
 - Ethernet Link Up/Down Handling	( SCGCQ00154872 port of SCGCQ00135540) 
 - UART commands addition for USB stack library interactions	( SCGCQ00154928 port of SCGCQ00147712) 
 - Thunderbolt: Increase max message frame to 1008	( SCGCQ00155272 port of SCGCQ00151477 ) 
 - Make miniDMA functionality into a stand alone library	( SCGCQ00155289 port of SCGCQ00145202) 
 - PL: Add compile option to fault when Discovery detects Discovery Error 0x90 (SMP Timeout	( SCGCQ00155434 port of SCGCQ00149166) 
 - USB code review changes	( SCGCQ00155947 port of SCGCQ00149031) 
 - IOP USB Test help menu is incorrect	( SCGCQ00157530 port of SCGCQ00150264) 
 - Firmware hangs after any MSC operation when no USB Drive attached	( SCGCQ00157768 port of SCGCQ00149313) 
 - Phase 8: IR: Misleading comments in Setting and clearing data Scrub allowed flag	( SCGCQ00159372 port of SCGCQ00155425) 
 - Fix debug print param count mismatches and add compile-time assertion which detects mismatches	( SCGCQ00159373 port of SCGCQ00156731) 
 - IR Load Balancing	( SCGCQ00159374 port of SCGCQ00154962) 
 - USB: Add comments to USB header	( SCGCQ00160105 port of SCGCQ00152373) 
 - USB library is not using correct IOP interface functions	( SCGCQ00160110 port of SCGCQ00151363) 
 - iop: iopidynmalloc(	( SCGCQ00160704 port of SCGCQ00153578) 
 - ManPage 8 Device Type BOOT_ROM and SEEPROM should be unique types( SCGCQ00160712 port of SCGCQ00151455) 
 - iop usb portstop halts firmware	( SCGCQ00160811 port of SCGCQ00149654) 
 - Don't fault if TM sent to an Expander	( SCGCQ00162814 port of SCGCQ00125874) 
 - (GEMINI	( SCGCQ00163396 port of SCGCQ00151857) 
 - (IOP-Only	( SCGCQ00163406 port of SCGCQ00157932) 
 - USB - CBW, CSW and Status incorrectly has only one instance for two ports	( SCGCQ00164453 port of SCGCQ00157667) 
 - USB - CBW, CSW and Status incorrectly has only one instance for two ports (duplicate of 157670	( SCGCQ00164468 port of SCGCQ00157670) 
 - USB - FW is not able to communicate with USB end device	( SCGCQ00164478 port of SCGCQ00157838) 
 - bld: Change enum TRACE to TRACEBUF	( SCGCQ00168226 port of SCGCQ00162009) 
 - PL: Add SAT translation of SCSI Unmap	( SCGCQ00168430 port of SCGCQ00143322) 
 - Extend Flash BIOS region to be 512 KBytes instead of the current size of 384 K	( SCGCQ00168435 port of SCGCQ00163940) 
 - Fix build all error with memcfg build	( SCGCQ00168442 port of SCGCQ00166402) 
 - Add temperature sensor read capability to uart	( SCGCQ00168563 port of SCGCQ00156735) 
 - PL: Add SAT translation of SCSI WRITE SAME with Unmap/Anchor	( SCGCQ00168595 port of SCGCQ00163761) 
 - MSCINIT command allocates only a sinlge structure instead of separate ones (For both USB ports	( SCGCQ00168680 port of SCGCQ00150531) 
 - IOP: SAS HD cable management support	( SCGCQ00169150 port of SCGCQ00159161) 
 - CSET: IR/WH: Performance improvements for very large IO sizes - (SCGCQ00152205	( SCGCQ00169767 port of SCGCQ00169767) 
 - Check in the syslog debug server to be used with tbolt	( SCGCQ00172036 port of SCGCQ00172035) 
 - SAS IO Unit page 6 length and data incorrect	( SCGCQ00172523 port of SCGCQ00162968) 
 - Add a check to avoid invalid function call that causes 265D fault when dumping configuration pages	( SCGCQ00172535 port of SCGCQ00171769) 
 -	( SCGCQ00172608 port of SCGCQ00165292) 
 - IR: Sense data incorrectly interpreted when the valid bit is set.( SCGCQ00172671 port of SCGCQ00170928) 
 - IOP: Need algorithm to handle copying boot up parameters where source and destination overlap.	( SCGCQ00172681 port of SCGCQ00169525) 
 - PL: Debug: Log Descriptor format sense data	( SCGCQ00172687 port of SCGCQ00169000) 
 - Allow Raid Accelerator if DDR memory isn't present	( SCGCQ00172755 port of SCGCQ00172276) 
 - (IOP-Only	( SCGCQ00177562 port of SCGCQ00161572) 
 - Reading Dma buffers via snapshot or UART while IOs are in progress	( SCGCQ00179463 port of SCGCQ00139946) 
 - DDR3: Training algorithm performance improvements	( SCGCQ00179991 port of SCGCQ00158325) 
 - IOP: Internal tools for use with DDR3 development	( SCGCQ00183664 port of SCGCQ00162983) 
 - IR: Repeated pulls/re-inserts of IR physical disk may cause 8109 fault	( SCGCQ00186472 port of SCGCQ00171520) 
 - Ethernet driver library	( SCGCQ00187588 port of SCGCQ00172827) 
 - IR: 8209 (IFAULT_IR_PD_ELM_NOT_FOUND	( SCGCQ00188498 port of SCGCQ00145932) 
 - Good status being returned on TM to missing SATA drive	( SCGCQ00188688 port of SCGCQ00159495) 
 - Substantial drop in allocated resources in phase 8	( SCGCQ00188774 port of SCGCQ00170571) 
 - (IOP-Only	( SCGCQ00188777 port of SCGCQ00176742) 
 - SATL: Need to update standard inquiry version descriptors	( SCGCQ00188781 port of SCGCQ00168345) 
 - Change ISTWI API and toolbox ISTWI READ WRITE API return values	( SCGCQ00188872 port of SCGCQ00180331) 
 - DDR3: Library fails to compile when some flags are turned off	( SCGCQ00190922 port of SCGCQ00179269) 
 - Diagnostic CLI Tool Returns Amount DMA'd on the overflow of the Host SGL	( SCGCQ00192197 port of SCGCQ00174823) 
 - 265D fault when posting a trace buffer after printing the ring buffer	( SCGCQ00192211 port of SCGCQ00187116) 
 - Duplicate data appears at start of diagnostic trace buffer	( SCGCQ00193239 port of SCGCQ00187262) 
 - Drives are not shown after flashing NB IT or IR pre-Alpha phase 10 image.	( SCGCQ00193241 port of SCGCQ00183646) 
 - Need to use the same frame for the event and reply	( SCGCQ00193242 port of SCGCQ00186699) 
 - USB: Modify UPLI phy settings to work on board when 5v isn't available.	( SCGCQ00193407 port of SCGCQ00174424) 
 - USB: An off the shelf stick does not work at all	( SCGCQ00193411 port of SCGCQ00176446) 
 - Update to handle large out of range max host credit setting in manufacturing page 9.	( SCGCQ00200640 port of SCGCQ00186348) 
 - (SRIOV-Only	( SCGCQ00201901 port of SCGCQ00176744) 
 - (SRIOV-Only	( SCGCQ00202160 port of SCGCQ00176731) 
 - (SRIOV-Only	( SCGCQ00202275 port of SCGCQ00176743) 
 - (SRIOV-Only	( SCGCQ00202289 port of SCGCQ00182855) 
 - (SRIOV-Only	( SCGCQ00203045 port of SCGCQ00176745) 
 - (SRIOV	( SCGCQ00203077 port of SCGCQ00152259) 
 - Ph11 IR: Cannot create/activate foreign volume if a native FAILED volume with no drive exists( SCGCQ00203875 port of SCGCQ00194882) 
 - Add newline after "NvdataVersion is"	( SCGCQ00203981 port of SCGCQ00190207) 
 - Remove warpdrive tag and unnecessary code from iButton code	( SCGCQ00204071 port of SCGCQ00183856) 
 - (SRIOV-Only	( SCGCQ00204098 port of SCGCQ00185967) 
 - IOP: fix minor bugs for CLI to display VF statistic info	( SCGCQ00204177 port of SCGCQ00190839) 
 - 0501 fault occurs after sending "iop show cfg all" command via uart	( SCGCQ00204206 port of SCGCQ00187446) 
 - (IOP-Only	( SCGCQ00204224 port of SCGCQ00163806) 
 - (NVDATA	( SCGCQ00204227 port of SCGCQ00185661) 
 - Activating a foreign volume results in 0x830A fault if a native FAILED volume with no drive exists( SCGCQ00207006 port of SCGCQ00194668 ) 
 - (NVDUMP only	( SCGCQ00209226 porrt of SCGCQ00189461) 
 - (FWHEAD Utility	( SCGCQ00209249 port of SCGCQ00192997) 
 - (PL&IOP	( SCGCQ00218354 port of SCGCQ00203441) 
 - Entire topology goes missing while injecting errors into DMA Setup FIS( SCGCQ00218404 port of SCGCQ00203694) 
 - USB: Add a command tag for requests/completions	( SCGCQ00224540 port of SCGCQ00188808) 
 - Add API's for Interrupt Handlers and Forces write check using DDR3/Tbolt	( SCGCQ00224791 port of SCGCQ00200272) 
 - Erase flash command syntax is given incorrectly in UART	( SCGCQ00225384 port of SCGCQ00203575) 
 - 0x707 fault on OEM specific PL log entry when HBA is host booted	( SCGCQ00228184 port of SCGCQ00207196) 
 - IR/WH: Performance improvements for very large IO sizes	( SCGCQ00228540 port of SCGCQ00152205) 
 - CSET: Improve the performance of adaptive heuristic queue depth algorithm - (SCGCQ00226755	( SCGCQ00235366 port of (SCGCQ00226755)) 
 - Child: Add PI to IR: Volume IOs	( SCGCQ00235422 port of SCGCQ00194010) 
 - Child: Add PI to IR: BGI Changes - Handle IO during BGI	( SCGCQ00235423 port of SCGCQ00194021) 
 - Child: Add PI to IR: Compatibility Checks	( SCGCQ00235605 port of SCGCQ00194024) 
 - Write cache value unchanged	( SCGCQ00235613 port of SCGCQ00143320) 
 - PI error occur during BGI for PI volumes	( SCGCQ00235620 port of SCGCQ00210546) 
 - When checking for PI error, sense key is not checked	( SCGCQ00235622 port of SCGCQ00210616) 
 - It may be possible for the volume's PI flag to be out of sync with the phys disks's flags	( SCGCQ00235623 port of SCGCQ00212995) 
 - Improve structure of checking for PI support	( SCGCQ00235654 port of SCGCQ00215883) 
 - DPICZ Required Flag not working as expected	( SCGCQ00235656 port of SCGCQ00216568) 
 - Non-PI volume is activated as PI	( SCGCQ00235661 port of SCGCQ00221023) 
 - RAID1E not working properly	( SCGCQ00235662 port of SCGCQ00218684) 
 - Child: Add PI to IR: Data Scrub	( SCGCQ00237159 port of SCGCQ00194034) 
 - 0x265D Fault Doing RAID Passthrough to a Hot Spare or Raw Disk	( SCGCQ00237596 port of SCGCQ00217042) 
 - DDR Write level training fails during initialization	( SCGCQ00237706 port of SCGCQ00208449) 
 - Child: Add PI to IR: BGI Changes - Add RAID0 Initialization	( SCGCQ00237873 port of SCGCQ00194019) 
 - Child: Add PI to IR: MDC and Resync	( SCGCQ00237885 port of SCGCQ00194036) 
 - IR: For IR Log IOPI_LOG_CODE_LD_BGI_CORRECTED_MEDIUM_ERROR LdLBA value is not correct for RAID1E/10	( SCGCQ00237886 port of SCGCQ00219886) 
 - FUA bit is not set for the Host Ios during BGI	( SCGCQ00237889 port of SCGCQ00221336) 
 - OCE is not happening as expected, after firmware upgrade from ph2.5 to ph10	( SCGCQ00238010 port of SCGCQ00192386) 
 - Gen2 FW Ph10 - Roaming of > 2TB SATA volume drives from SAS1 to SAS2 cards, shows the volume drives as bare drives.	( SCGCQ00238011 port of SCGCQ00189445) 
 - Ph12 FW: 8401 faults hits while removing a volume from the controller	( SCGCQ00238012 port of SCGCQ00223345) 
 - Fault 8405 when a drive removed from a PI volume during BGI	( SCGCQ00238283 port of SCGCQ00221611) 
 - IR: Adaptive HQD for R1/R10 for load balancing	( SCGCQ00238383 port of SCGCQ00193113) 
 - Sense data for the >2TB SAS drive remains in fixed format only & no change is seen to descriptor format	( SCGCQ00238405 port of SCGCQ00188760) 
 - (DDR3	( SCGCQ00238562 port of SCGCQ00225388) 
 - 5861 fault after link related parity errors	( SCGCQ00240778 port of SCGCQ00183364) 
 - BIOS Page 4 not behaving per MPI specification	( SCGCQ00246850 port of SCGCQ00227809) 
 - (IOP-Only	( SCGCQ00250540 port of SCGCQ00221349) 
 - Remove second physical function references from h/w header files	( SCGCQ00250725 port of SCGCQ00168552) 
 - Build: create symbol and structure dump files	( SCGCQ00250747 port of SCGCQ00231195) 
 - Add NVDATA bit to disable Notify(Enable Spinup	( SCGCQ00250752 port of SCGCQ00208630) 
 - (BUILD-Only	( SCGCQ00253252 port of SCGCQ00193624) 
 - Disable the internal HW interrupt to the FW for receiving the BROADCAST(Change	( SCGCQ00254237 port of SCGCQ00204210) 
 - Uart commands are available via Toolbox Diagnostic CLI Tool after a firmware fault	( SCGCQ00254429 port of SCGCQ00220613) 
 - Correct fault code & log info comments & spelling	( SCGCQ00254921 port of SCGCQ00229108) 
 - pl: SATL: Add handling of security locked state	( SCGCQ00257362 port of SCGCQ00223621) 
 - Assign all targets and SSP initiators to a non-zero DMA Group	( SCGCQ00259862 port of SCGCQ00235650) 
 - Embedded strings in host trace are corrupted	( SCGCQ00269272 port of SCGCQ00238503) 
 - IOC state transition and Interrupt bit cleaning issue by MUR Issue	( SCGCQ00279891 port of SCGCQ00245892) 
 - (BUILD	( SCGCQ00280059 port of SCGCQ00238155) 
 - IOP: Remove un-needed I2C ring buffer print in I2C Write	( SCGCQ00280168 port of SCGCQ00235614) 
 - A diag reset is issued by the driver when resync starts on a RAID 1 volume.	( SCGCQ00292969 port of SCGCQ00269340) 
 - Fault 0x8111 seen while Activating a Degraded Raid 10 Volume	( SCGCQ00294706 port of SCGCQ00237555) 
 - Reassign Block command fails with check condition 5/1A/00	( SCGCQ00294979 port of SCGCQ00242855) 
 - PI error reported when PI error detected due to a frame CRC error( SCGCQ00314686 port of SCGCQ00262937) 
 - (DDR3	( SCGCQ00314711 port of SCGCQ00235393) 
 - One of the inactive volumes member becomes offline/missing	( SCGCQ00316967 port of SCGCQ00283314) 
 - Event for BGI started ('2F'	( SCGCQ00316968 port of SCGCQ00282792) 
 - When ios are running with cable break and make (b/w expander and drive	( SCGCQ00316969 port of SCGCQ00280375) 
 - Internal Task Management events aren't blocked for IR	( SCGCQ00316975 port of SCGCQ00237568) 
 - SAS2 IT - Phase 14 – Request Sense SCSI Command data is incorrect for a SATA Drive During Stanby Power Condition Mode( SCGCQ00317952 port of SCGCQ00283312) 
 - Update field offsets of GPIOs above GPIOs 32.( SCGCQ00320004 port of SCGCQ00177385) 
 - (DDR3	( SCGCQ00320041 port of SCGCQ00257631) 
 - Truncated Data is Obtained When SCSI Inquiry to VPD Page 0xB0 is Executed	( SCGCQ00320058 port of SCGCQ00285500) 
 - Some host trace buffers don't decode properly( SCGCQ00320157 port of SCGCQ00235357) 
 - Change text for "iop show cfg" to show or 	( SCGCQ00321281 port of SCGCQ00257451) 
 - PL: Configurable AWT for Expanders	( SCGCQ00335507 port of SCGCQ00241199) 
 - (DDR3	( SCGCQ00335517 port of SCGCQ00295262) 
 - Ph15 SAS2 IR Firmware: Hotspare does not resync with second raid volume when both the volumes are in degraded state	( SCGCQ00336453 port of SCGCQ00333684) 
 - Toolbox Clean Tool does not work with phase 11 FW	( SCGCQ00434174 port of SCGCQ00220095) 
 - Define config page ranges to be used by various projects (no code change	( SCGCQ00434182 port of SCGCQ00293081) 
 - PL: Configurable SMP retries	( SCGCQ00437960 port of SCGCQ00271092) 
 - Invader: Enable SAS Core Parity Interrupts	( SCGCQ00449638 port of SCGCQ00361839) 
 - Remove power management control flags from Manufacturing Page 3	( SCGCQ00450890 port of SCGCQ00293362) 
 - Invader C0: Firmware should fault if a parity error is deteced while reading asynchronous event from fast path hardware.	( SCGCQ00451375 port of SCGCQ00377564) 
 - Invader B0: Firmware not using correct start address while handling data overrun interrupt	( SCGCQ00462166 port of SCGCQ00351468) 
 - Invader: Fixed Issue Found in Data Overrun Testing Where IOs Were Being Incorrectly Completed( SCGCQ00463429 port of SCGCQ00363670) 
 - IOP: Firmware does not react to OCM interrupt	( SCGCQ00465082 port of SCGCQ00377585) 
 - Firmware download via rFTP fails on large images	( SCGCQ00467609 port of SCGCQ00234446) 
 - Changed Value Set for RAID Engine Polynomial for RAID6	( SCGCQ00468672 port of SCGCQ00343306) 
 - Serdes settings to fix 12G SSC profile	( SCGCQ00468679 port of SCGCQ00343925) 
 - (IOP	( SCGCQ00469157 port of SCGCQ00377964) 
 - Fault 0x820 on cold boot	( SCGCQ00469444 port of SCGCQ00380312) 
 - IOP: 0x000B fault( SCGCQ00469667 port of SCGCQ00193071) 
 - Add Uart diag cmd to read and write GPIO.( SCGCQ00469768 port of SCGCQ00200629) 
 - Syslog server script chops off end of string	( SCGCQ00471486 port of SCGCQ00365924) 
 - (IOP	( SCGCQ00471989 port of SCGCQ00384661) 
 - Added support for AUTO RESERVE on I2C toolbox request.	( SCGCQ00472600 port of SCGCQ00349976) 
 - (GEMINI	( SCGCQ00472914 port of SCGCQ00146873) 
 - WA for [invader]1752	( SCGCQ00472980 port of SCGCQ00355461) 
 - Program the pre-loaded preset used to lock-in the bitstream at the start of Tx Training	( SCGCQ00473943 port of SCGCQ00354681) 
 - Transmitter Training Part 1	( SCGCQ00474680 port of SCGCQ00357497) 
 - The IOCStatus returned for ToolBox I2C requests is incorrect.	( SCGCQ00475527 port of SCGCQ00353295) 
 - Messaging unit security configuration fails	( SCGCQ00476784 port of SCGCQ00348956) 
 - PCIe SerDes registers inaccessible over AHB bus	( SCGCQ00476819 port of SCGCQ00364456) 
 - Update release script to release raw FW with useful names	( SCGCQ00477176 port of SCGCQ00354759) 
 - Transmitter Training Part 2	( SCGCQ00480619 port of SCGCQ00364214) 
 - Invader C0: Performance drops with PL version 0.250.113.0 on 2 R0 volumes behind Cobra	( SCGCQ00494101 port of SCGCQ00400569) 
 - PL: Check iopiMemoryMove(	( SCGCQ00498849 port of SCGCQ00419472) 
 - PL: SAT3 Compliance - Implement Translation of Set Timestamp Command (Disabled	( SCGCQ00503815 port of SCGCQ00357128) 
 - PL: SAT3 Compliance - Implement Translation of Report Timestamp Command (Disabled	( SCGCQ00528525 port of SCGCQ00357126) 
 - (IOP	( SCGCQ00552411 port of SCGCQ00375164) 
 - IOP: Log Entry SubVendorID not set properly	( SCGCQ00552462 port of SCGCQ00391022) 
 - PL: SAT3 compliance - Support additional modes for Write Buffer command translation (Disabled( SCGCQ00553455 port of SCGCQ00357130) 
 - PL: SAT3 compliance - Support for ATA EPC in SCSI Start Stop Unit command translation.( SCGCQ00553489 port of SCGCQ00357136) 
 - PL: SAT3 Compliance – Implement Power Condition Mode Page translation with ATA EPC.	( SCGCQ00553528 port of SCGCQ00406792) 
 - (IOP-only	( SCGCQ00556108 port of SCGCQ00298490) 
 - PL Host Based Discovery updates for Gen 3	( SCGCQ00556327 port of SCGCQ00395436) 
 - PL: Move temperature sensor init code down to PL	( SCGCQ00556330 port of SCGCQ00410822) 
 - (IOP	( SCGCQ00563042 port of SCGCQ00419437) 
 - IOP: DPA Capability number of D0 states programmed incorrectly	( SCGCQ00563332 port of SCGCQ00396420) 
 - IOP: I2C master wastes time doing an I2C write packet	( SCGCQ00563335 port of SCGCQ00411656) 
 - Recreation of persistent Config Pages fails after full erase	( SCGCQ00563339 port of SCGCQ00397870) 
 - IOP: SR-IOV: Firmware fails to reply to Set Visibility command request message	( SCGCQ00563409 port of SCGCQ00419034) 
 - IOP: SR-IOV visibility modification causes fault 0x060D	( SCGCQ00563411 port of SCGCQ00423670) 
 - (IOP	( SCGCQ00563421 port of SCGCQ00435265) 
 - IOP: Handle miscellaneous PCI-Express core interrupts	( SCGCQ00564303 port of SCGCQ00412062) 
 - IOP: Sideband Create initial support for SMBus/I2C binding for MCTP	( SCGCQ00565507 port of SCGCQ00394111) 
 - IOP: PCIe link speed and receiver errors	( SCGCQ00566083 port of SCGCQ00396364) 
 - IO on a SATA SSD configured as JBOD pending with PL does not complete	( SCGCQ00566089 port of SCGCQ00407250) 
 - IOP: I2C DMA Complete interrupt does not trigger after Master mode transmission of unacknowledged consecutive large packet	( SCGCQ00566094 port of SCGCQ00418148) 
 - IOP: Memory Coherency not enabled in Detroit	( SCGCQ00566099 port of SCGCQ00432917) 
 - Invader: The CLI commands need to have their text consistent.( SCGCQ00566120 port of SCGCQ00457380) 
 - iop pci commands need to be updated to use dword instead of word to be consistent( SCGCQ00566123 port of SCGCQ00457386) 
 - Invader: pl fpe mgrdstt cannot be called. pl fpe mgrds gets called instead.	( SCGCQ00566133 port of SCGCQ00457412) 
 - Invader C0: PCIe Compliance test failing because DPA Transition Latency offsets in firmware and the Trident EDS are incorrect( SCGCQ00566137 port of SCGCQ00460941) 
 - Update coalescing setup for Combined Reply Queue mode( SCGCQ00566160 port of SCGCQ00476245) 
 - Subsystem Device ID should match the Device ID in default NVData files	( SCGCQ00566161 port of SCGCQ00476286) 
 - PL: Fault 0x6001 while running heavy IOs and performing cable break of the initiator port.	( SCGCQ00566162 port of SCGCQ00479492) 
 - (IOP	( SCGCQ00566167 port of SCGCQ00484049) 
 - FW trace released when the Operational state	( SCGCQ00566193 port of SCGCQ00526257) 
 - PL: Turn SSC on by default in the NVDATA for C0 silicon.	( SCGCQ00566214 port of SCGCQ00415063) 
 - Controller Initialization: Fault if SBR values were not loaded from SEEPROM	( SCGCQ00566218 port of SCGCQ00426920) 
 - Update SAS9300-8i IT NVDATA for Channel configuration requirements	( SCGCQ00566220 port of SCGCQ00436396) 
 - Security: Signed firmware update	( SCGCQ00566227 port of SCGCQ00462139) 
 - Enclosure/Slot based re-ordering of SAS Topology List Event	( SCGCQ00566231 port of SCGCQ00472198) 
 - Check iopiMemoryMove(	( SCGCQ00566243 port of SCGCQ00476305) 
 - IOP debug string cleanup	( SCGCQ00566258 port of SCGCQ00485420) 
 - Invader: Remove A0 support in firmware	( SCGCQ00566260 port of SCGCQ00488494) 
 - Allow users to select Transmitter Training preset in NVDATA	( SCGCQ00566264 port of SCGCQ00501485) 
 - Add Temperature Monitoring Capability	( SCGCQ00567337 port of SCGCQ00168446) 
 - IOP: Add descriptions for errata that has not been worked around	( SCGCQ00568404 port of SCGCQ00422101) 
 - ONFI: Minor updates to the ONFI diag commands	( SCGCQ00568411 port of SCGCQ00448626) 
 - Add MR PL builds with Target Mode enabled	( SCGCQ00568412 port of SCGCQ00457382) 
 - Add lwIP license file to release file	( SCGCQ00568413 port of SCGCQ00468546) 
 - IOP: Update PCIe SERDES with improved settings	( SCGCQ00568481 port of SCGCQ00408335) 
 - (IOP	( SCGCQ00568489 port of SCGCQ00370060) 
 - SAS2IT: Incorrect SAT translation observed when sending a Security IN command with zero Allocation length with INC_512=1	( SCGCQ00568500 port of SCGCQ00452375) 
 -	( SCGCQ00572869 port of SCGCQ00421676) 
 - Intruder FPGA Release 2.0 interrupt map	( SCGCQ00685741 port of SCGCQ00681295) 
 - IOP: Target Mode performance improvements	( SCGCQ00711577 port of SCGCQ00685827) 
 - Target Mode: Task IU is sent to the IOP before it knows about the Initiator	( SCGCQ00725158 port of SCGCQ00606248) 
 - MCTP GET_INVENTORY returning wrong deviceType	( SCGCQ00725159 port of SCGCQ00615192) 
 - IOP: PowerPC ITLB Miss Errata Workaround	( SCGCQ00725162 port of SCGCQ00634879) 
 - 12G SAS BC train fails with 6M cable between Fury and Cobra	( SCGCQ00725164 port of SCGCQ00678053) 
 - PL: Incorrect use of IOP LogInfo code	( SCGCQ00725173 port of SCGCQ00709517) 
 - Invader: Update Fault and LogInfo codes based on Tech Pubs SEN 11218	( SCGCQ00725195 port of SCGCQ00531238) 
 - PL: Reduce IOC Link Up Initialization Time	( SCGCQ00725208 port of SCGCQ00414458) 
 - IOP: Successive resets may cause Invader/Fury to stop responding on PCIe	( SCGCQ00725216 port of SCGCQ00556766) 
 - Unexpected IOCStatus with invalid config page type	( SCGCQ00725229 port of SCGCQ00551008) 
 - Invader C0: MPI PM Global Request Change to Reduced or Standby state results in "Operation State Not Supported" or "IOC Busy"	( SCGCQ00725237 port of SCGCQ00584284) 
 - Invader C0: MPI PM IOC Change Request from 50% to 100%, IO Unit Page 7 says speed stays at 50%	( SCGCQ00725238 port of SCGCQ00584288) 
 - Interrupt coalescing stopped working with SAS3 driver version 2.50.65	( SCGCQ00725244 port of SCGCQ00593491) 
 - IOP: I2C Read of non-existent device causes infinite-loop and FW is stalled	( SCGCQ00725263 port of SCGCQ00673161) 
 - NVData: Update SBR to reflect new HW/SE recommendations	( SCGCQ00725275 port of SCGCQ00498550) 
 - DFE tuning	( SCGCQ00725276 port of SCGCQ00505626) 
 - SATL: Implemented Power Condition VPD Page (0x8A	( SCGCQ00725278 port of SCGCQ00524989) 
 - Implement means of saving critical OEM config data so that it can easily be persisted through a firmware down-rev.	( SCGCQ00725283 port of SCGCQ00566512) 
 - Compile out unnecessary debug strings	( SCGCQ00725285 port of SCGCQ00604550) 
 - Raid Accelerator IOs can hang if the stream of IOs suddenly stops	( SCGCQ00725307 port of SCGCQ00503412) 
 - NVData: MfgPg2 is configured for 16 Virtual Functions with non-SRIOV firmware	( SCGCQ00725327 port of SCGCQ00614550) 
 - IOP SR-IOV: Fault 0x265D seen when issuing Function Level Resets after a firmware fault	( SCGCQ00725330 port of SCGCQ00664517) 
 - IOP MCTP: Uninitialized variables need correcting	( SCGCQ00725331 port of SCGCQ00668686) 
 - IOP: Recursive fault may not report fault state to host	( SCGCQ00725337 port of SCGCQ00641946) 
 - IOP SR-IOV: Devices in SAS Topology Change List Event are incorrectly ordered	( SCGCQ00725338 port of SCGCQ00655407) 
 - IOP SR-IOV: Firmware fails to clear visibility settings on removed devices	( SCGCQ00725339 port of SCGCQ00668564) 
 - IOP: WA for Inbound Message Queue enable bit surviving resets in Trident with reset Inbound Message Queue regs	( SCGCQ00725343 port of SCGCQ00663100) 
 - Fixed multiple order of operation bugs	( SCGCQ00725346 port of SCGCQ00626966) 
 - IOP: PCIe Link Down can cause Transmit Margin field to not reset	( SCGCQ00725356 port of SCGCQ00663185) 
 - PL: Add fault code to indicate coding error in cable management code	( SCGCQ00725358 port of SCGCQ00668692) 
 - IOP SR-IOV: Controller reports 16 MSIx vectors in the MSIx Table Size field of the Config Space	( SCGCQ00725363 port of SCGCQ00655251) 
 - IOP: Incorrect PCIe SERDES settings	( SCGCQ00725364 port of SCGCQ00661564) 
 - IOC Fault 0x1609 by Message Unit Reset	( SCGCQ00725365 port of SCGCQ00582515) 
 - IOP SR-IOV: Reply Descriptor Post Queue Array from VFs during heavy load causes 0x0A05 fault	( SCGCQ00725371 port of SCGCQ00670932) 
 - IOP: MCTP: EIDAllocStatus and EIDAssignStatus in MCTP Control Set EID response swapped	( SCGCQ00725372 port of SCGCQ00675342) 
 - Inquiry SCSI Command is Not Failed with Expected Response When NACA bit in Control Byte is set during During Format	( SCGCQ00725376 port of SCGCQ00649572) 
 - IOP MCTP: Add support for VDM Buffers	( SCGCQ00725381 port of SCGCQ00626865) 
 - IOP MCTP: Add support for resetting EID in MCTP Control Set EID command	( SCGCQ00725382 port of SCGCQ00631600) 
 - Selective Extended Image Loading	( SCGCQ00725384 port of SCGCQ00595519) 
 - PL: Poll for parity error in FPE PLB Slave	( SCGCQ00725388 port of SCGCQ00645401) 
 - Add PL source build package into MR build script	( SCGCQ00755353 port of SCGCQ00715730) 
 - Firmware downgrade fails and firmware faults with code 0x070A	( SCGCQ00757685 port of SCGCQ00592281) 
 - IOP: Force sequence point evaluation	( SCGCQ00781306 port of SCGCQ00728929) 
 - IOP: Fault 0x265D hit when booting controller with attached enclosure	( SCGCQ00781332 port of SCGCQ00709712) 
 - IOP: MCTP: Miscellaneous transmission path issues	( SCGCQ00781335 port of SCGCQ00710168) 
 - Module Specific Resets 0 is missing the PBAM AI bit	( SCGCQ00781336 port of SCGCQ00710445) 
 - PL: Fix minor code issues found by analysis tool	( SCGCQ00781349 port of SCGCQ00728016) 
 - IOP: Diag Buffer Post request message with invalid BufferType field can cause unpredictable results	( SCGCQ00781352 port of SCGCQ00728152) 
 - IOP: DDR initialization may access invalid pointer	( SCGCQ00781355 port of SCGCQ00728153) 
 - IOP: Minor CLI defects	( SCGCQ00781362 port of SCGCQ00728908) 
 - IOP: Incorrect MaxChainDepth in IOC Facts response with disabled local chain HW	( SCGCQ00781367 port of SCGCQ00730628) 
 - PL: Firmware could be accessing null pointer in port layer interrupt handler.	( SCGCQ00781369 port of SCGCQ00730721) 
 - IOP: MCTP: I2C slave-response mode fails to fully complete initalization	( SCGCQ00781379 port of SCGCQ00757474) 
 - IOP: MCTP: Get Version, Get MsgType Support, and Get UUID MCTP Control Commands	( SCGCQ00781385 port of SCGCQ00679104) 
 - IOP: MCTP: Add support for MPI FW Upload Request	( SCGCQ00781387 port of SCGCQ00691019) 
 - NVDATA: Increase maximum supported ManPage13 entries from 16 to 32	( SCGCQ00781388 port of SCGCQ00695575) 
 - Allow MaxChainDepth as a configurable parameter in Manufacturing Page 9	( SCGCQ00781389 port of SCGCQ00696232) 
 - IOP: Deassert the HSB_N line when NVSRAM is available	( SCGCQ00781391 port of SCGCQ00705414) 
 - PL Target Mode: Implement multi reply queue handling of command buffers	( SCGCQ00781392 port of SCGCQ00709549) 
 - IOP: Controller does not respond to doorbell messages after faulting through the doorbell	( SCGCQ00781396 port of SCGCQ00764912) 
 - Update PL firmware to have capability to not fault on Rx/Tx DMA engine SYS_DMA error	( SCGCQ00785193 port of SCGCQ00678819) 
 - IOP: When flashing IT firmware with sas3flash DOS, the system hangs if the SAS address is included on the command line.	( SCGCQ00791427 port of SCGCQ00769327) 
 - IOP: Argument in print for SAS Topology Change has items reversed	( SCGCQ00793914 port of SCGCQ00780174) 
 - Controller (L85a Pollux installed to Dell servers R720XD / R820	( SCGCQ00793915 port of SCGCQ00702655) 
 - IOP: MPI Toolbox Clean Tool incorrect pointer arithmetic	( SCGCQ00793919 port of SCGCQ00730739) 
 - PL: PL code is not checking the return status of a function call	( SCGCQ00793925 port of SCGCQ00737080) 
 - IOP: SR-IOV firmware faults with lots of TM and outstanding IO	( SCGCQ00793933 port of SCGCQ00757482) 
 - Target Mode performance improvements	( SCGCQ00793943 port of SCGCQ00698205) 
 - IOP: MCTPMsg: Add command to obtain individual entries from Log Page 0 Config Page and Log Page 0 to ExtEvents	( SCGCQ00793945 port of SCGCQ00734303) 
 - PL: Yellow LED Function Code control LEDs using MfgPage13 for link up and link speed	( SCGCQ00793949 port of SCGCQ00741955) 
 - IOP: MCTPMsg: Add Sense Data support to MPI SCSI IOs	( SCGCQ00793950 port of SCGCQ00751428) 
 - IOP: MCTP: Add support for the Vendor Defined Message Support MCTP Control request	( SCGCQ00793952 port of SCGCQ00761033) 
 - PL: SATA Spinup Hinting	( SCGCQ00793954 port of SCGCQ00767301) 
 - Target Mode performance improvements	( SCGCQ00805047 port of SCGCQ00698205) 
 - IOP: MCTP: Comment flexibility improvement for I2C slave response mode	( SCGCQ00816408 port of SCGCQ00804070) 
 - IOP: Check for failure when DMAing diag buffer strings	( SCGCQ00816413 port of SCGCQ00787491) 
 - PL: Fault 0xD203 observed while releasing Diag Buffer (TRACE	( SCGCQ00816415 port of SCGCQ00792742) 
 - (DDR3	( SCGCQ00831254 port of SCGCQ00531317) 
 - New DDR3 library API to obtain ECC information and return it to the caller	( SCGCQ00831262 port of SCGCQ00333267) 
 - WW PL: Add MPI PCIe Device driver	( SCGCQ00832573 port of SCGCQ00795210) 
 - Config page write request for new SAS BIOS Page3 (NVRAM copy	( SCGCQ00836785 port of SCGCQ00829028) 
 - CSET: IOP: WA Config Trap Timer not fully clearing - (SCGCQ00836313	( SCGCQ00836879 ) 
 - Tiger WW: Add Storage Expansion Device interrupt handler and initialization	( SCGCQ00837237 port of SCGCQ00797527) 
 - Tiger WW: Change how remote SAS core interrupts are handled	( SCGCQ00837761 port of SCGCQ00798076) 
 - Tiger WW: Update SED MPI messages to 0.2 revision	( SCGCQ00841600 port of SCGCQ00831478) 
 - PL: Firmware should return an error if an invalid slot number is sent in a MPI SEP request	( SCGCQ00848133 port of SCGCQ00824715) 
 - IOP: MCTP: Cannot see drive add and remove events with I2C configuration	( SCGCQ00848142 port of SCGCQ00810264) 
 - IOP: MCTP: I2C interrupt not always cleared before exiting when in slave response mode	( SCGCQ00848201 port of SCGCQ00833480) 
 - Multiplexed I2C bus is switched too early	( SCGCQ00851640 port of SCGCQ00809980) 
 - Fix Loginfo Names and Comments	( SCGCQ00851646 port of SCGCQ00835465) 
 - UART: Add new test patterns to testmux test command	( SCGCQ00851655 port of SCGCQ00815682) 
 - IOP: When certain PCIe timeouts occur in the presence of Link Unavailable, a hang condition can occur	( SCGCQ00852084 port of SCGCQ00755510) 
 - The lock option of the Low Power self refresh command may cause system to hang upon reset after DDR fault.	( SCGCQ00858181 port of SCGCQ00857473) 
 - NVDump: SBR extraction creates incorrect SBR	( SCGCQ00861767 port of SCGCQ00859080) 
 - Coverity issues :IOP: MCTP: Event information not populated properly, uninitialized variables, NULL and Return Check missing.	( SCGCQ00871132 port of SCGCQ00852066) 
 - Gen-3 is not supporting SES Page 0x0A slot mapping mode fully	( SCGCQ00872845 port of SCGCQ00855132) 
 - System Hangs after Adapter reset with heavy IO load	( SCGCQ00875779 port of SCGCQ00646625) 
 - IOP: IT firmware faults with 0x1403	( SCGCQ00882243 port of SCGCQ00882204) 
 - PL: Check in Intruder A1 serdes setting	( SCGCQ00882320 port of SCGCQ00882269) 
 - IOP: Add code to stop additional hardware upon adapter reset	( SCGCQ00885542 port of SCGCQ00883655) 
 - PL: Fix FPE state machine transition flaw which could cause long I/O latency	( SCGCQ00885561 port of SCGCQ00884179) 
 - IOP: Low Level Workarounds for PCIe core compiled out	( SCGCQ00886309 port of SCGCQ00884738) 
 - IOP: 2622 fault while running stress test in CM	( SCGCQ00886311 port of SCGCQ00884076) 
 - NVDATA: Revise 9305-16e Partial NVDATA So it Matches Latest Schematic	( SCGCQ00887001 port of SCGCQ00885715) 
 - NVDATA: Revise 9305-24i/16i Partial NVDATA So it Matches Latest Schematic	( SCGCQ00887002 port of SCGCQ00885576) 
 - PL: Cleanup discovery code for improved maintainability	( SCGCQ00894149 port of SCGCQ00872750) 
 - New pliControlRequest to clear FPE bit in FPE flags of mid state table	( SCGCQ00894180 port of SCGCQ00817050) 
 - IOP: CLI Tool through doorbell not working when in fault state	( SCGCQ00894196 port of SCGCQ00875758) 
 - Selective Extended Image Loading	( SCGCQ00894703 port of SCGCQ00595519) 
 - PL: Use Dual Contexts in Tx Context Manager Only When Expanders Are Present	( SCGCQ00918136 port of SCGCQ00419356) 
 - IOP: MCTP: Seeing extra byte in second I2C packet of a message	( SCGCQ00925201 port of SCGCQ00916929) 
 - PL SATL: SCSI ATA Passthrough Code Should Check For Correct CDB Length	( SCGCQ00926753 port of SCGCQ00915201) 
 - IOP: False Reply Parity Error Firmware Workaround	( SCGCQ00929814 port of SCGCQ00927500) 
 - Tiger: Fix tiger release cmd file	( SCGCQ00948440 port of SCGCQ00948227) 
 - Tiger: add zip file for build, update version to avoid confusion with prior relorder	( SCGCQ00948441 port of SCGCQ00948409) 
 - IOP: MCTP: Bad CRC calculation for some Packet Exception Busy Retry responses	( SCGCQ01019764 port of SCGCQ01019438) 
 - SMR Host Aware and Host Managed drive support & ZBC to ZAC SATL	( SCGCQ01025897 port of SCGCQ00900453) 
 - The INQUIRY command over MCTP did not return the expected response data for an I2C attached SCSI enclosure processor based backplane	( SCGCQ01064022 port of SCGCQ00896512) 
 - Increase BIOS flash region from 512KB to 1MB for additional Boot Components	( SCGCQ01067775 port of SCGCQ01064581) 
 - Fast back-to-back or parallel PCIe configuration requests after certain addresses can generate bad Config Read data	( SCGCQ01070733 port of SCGCQ01047773) 
 - Build failure if MCTP is enabled and Config trap Hardware WorkAround is disabled.	( SCGCQ01084506 port of SCGCQ01075828) 
 - Add the Command line support to send the MCTP commands	( SCGCQ01084606 port of SCGCQ01064599) 
 - IOP: MCTP: I2C slave with high MPI request rate from host and BMC can cause a host request timeout	( SCGCQ01089469 port of SCGCQ01087653) 
 - Return EEDP/DIF error data of the first error frame detected by the hardware during READ in the MPI Reply error message frame	( SCGCQ01092128 port of SCGCQ01000193) 
 - PL: Discovery due to non responding SATA drive is now timed to last for the amount of seconds configured in NVDATA	( SCGCQ01092176 port of SCGCQ00996678) 
 - IOP: 'iop show cfg all' command is not listing all Expander's config pages	( SCGCQ01118590 port of SCGCQ01110070) 
 - IOP: MCTP: Cannot boot and discover controller with PCIe VDM and Bus Master Enable not set	( SCGCQ01132394 port of SCGCQ01107260) 
 - IOP: MCTP: Reply message may not contain expected data	( SCGCQ01154962 port of SCGCQ01154952) 
 - IOP: MCTP: application sees unexpected severe errors for removed/not registered drives and reset controller	( SCGCQ01158779 port of SCGCQ01150838) 
 - IOP: MCTP: Outstanding aborted SCSI IO due to too many PE Busy Retries is not being fully aborted within FW	( SCGCQ01167509 port of SCGCQ01167407) 
 - IOP: MCTP: Fix minor issues	( SCGCQ01172194 port of SCGCQ01171294) 
 - CSET: Upadate Intruder/Cutlass NVDATA for eval boards - (SCGCQ01134722	( SCGCQ01195990 ) 
 - EPMR12 : PR fails to continue on PD after a USER paused Patrol read is resumed after OCR.	( SCGCQ01198935 port of SCGCQ01130036) 
 - MRFW : Exception in Core 0 while importing Foreign Config with enclosure connections swapped.	( SCGCQ01198954 port of SCGCQ01117839) 
 - W fails to import DIF arrays, after changing enable PI controller property 0 -> 1	( SCGCQ01198958 port of SCGCQ01135815) 
 - Build the Flash Component List only if any of the image is flashed.	( SCGCQ01198964 port of SCGCQ01151384) 
 - IOP: MCTP: Heavy traffic from host with operations that take a long time can cause controller to stop acknowledging I2C transactions	( SCGCQ01203062 port of SCGCQ01196986) 
 - Linux,Intruder-eSDS-MR6.12 Replan RC: -6% to -15% Perf drop in all IO size with Higher QD in 12G SAS HDD [x16EC,x24EC,x40EC]	( SCGCQ01204998 port of SCGCQ01193231) 
 - Ventura PL: Add support to existing pli control request to do additional PL housekeeping for a stale MID	( SCGCQ01209109 port of SCGCQ01204327) 
 - Cutlass(16e and 24i	( SCGCQ01215350 port of SCGCQ01197319) 
 - New partial xml for 9400-8i8e channel HBA	( SCGCQ01217319 port of SCGCQ01217035) 
 - IOP: MCTP I2C: FW Download sometimes causes controller to be unresponsive	( SCGCQ01220370 port of SCGCQ01219591) 
 - PL: Support slot numbers starting at an arbitrary number	( SCGCQ01221523 port of SCGCQ01211733) 
 - PL: Long Firmware Wait During Tx Context Cleanup	( SCGCQ01232194port of SCGCQ01157345) 
 - Windows MR6.13 Alpha-eSDS Invader:-7 to -13% Perf Drops SR IO Sizes-4K,8K,16K QD(8	( SCGCQ01236372 port of SCGCQ01208167) 
 - Assertion failure in ../../dm/mpt2/mptrec.c at line 3139, while performing cable pull/push operation.	( SCGCQ01238553 port of SCGCQ01235505) 
 - IOP: Enable fault 0x2810	( SCGCQ01246726 port of SCGCQ01246717) 
 - Diagnostics report of iMR Invader contains information about R6 and R60 is set to 0	( SCGCQ01249579 port of SCGCQ01235661) 
 - Ventura: Firmware Hangs on Cold Boot of Slow Parts	( SCGCQ01251642 port of SCGCQ01250734) 
 - IOP: MCTP: Controller Fault 0x265D observed with running MCTP over PCIe VDM requests through controller reset( SCGCQ01254724 port of SCGCQ01250821) 
 - IOP: MCTP: Bus Master failed to discover MCTP EID during Ventura Port Enable	( SCGCQ01254725 port of SCGCQ01254021) 
 - SGPIO clock running at 100.7 KHz when set to 100Khz	( SCGCQ01260750 port of SCGCQ01234457 )
 - IOP: MCTP: MPI FW Download over MCTP PCI VDM	( SCGCQ01262853 port of SCGCQ01236956) 
 - IOP: MCTP: FW Download over MCTP PCIe VDM sometimes sees the checksum of the image fail	( SCGCQ01262870 port of SCGCQ01241620) 
 - NVMe backplane detection and device discovery fails on OEM specific server NVMe backplane	( SCGCQ01278820 port of SCGCQ01274101) 
 - PL : Add Support for PUIS(Power Up In Standby	( SCGCQ01280342 port of SCGCQ01174618) 
 - PL: BIOS Stuck when firmware is using 'Device Slot Number' for Bay number displaying	( SCGCQ01311448 port of SCGCQ01275770) 
 - PL : Enclosure LEDs won't blink if slot numbers are not sequential	( SCGCQ01313969 port of SCGCQ01291784) 
 - PL:Customer specific drive enumeration	( SCGCQ01315240 SCGCQ01198341) 
 - PL : Fault 0x7c71 hit when 24 drives connected to 3224 controller is powered up	( SCGCQ01318438 port of SCGCQ01309751) 
 - Ventura/Marlin: Continual Sequences of Adapter Reset followed by host boot when only the CBB is present causes the A15 to freeze	( SCGCQ01321823 port of SCGCQ01297690) 
 - Design changes update on NVME drive hotswap feature and updating more changes	( SCGCQ01327717 port of SCGCQ01319426) 
 - Ventura: AltData select, RefClk Mux not setup for SGPIO initiator prior to init	( SCGCQ01328966 port of SCGCQ01321764) 
 - pl: backend PCIe: specific vendor NVMe device does not appear to host software	( SCGCQ01337626 port of SCGCQ01328743) 
 - Ventura: Detect invalid BP_TYPE types in VPP backplane Mgmt connector group	( SCGCQ01342775 port of SCGCQ01332062) 
 - (NVMe Only	( SCGCQ01343513 port of SCGCQ01325987) 
 - (NVMe Only	( SCGCQ01343518 port of SCGCQ01325987) 
 - Ventura: Task Management to NVMe drives may not complete	( SCGCQ01345808 port of SCGCQ01330747) 
 - Ventura: NVDATA option to ignore BP_TYPE check and force enable PCIe RefClk for NVMe backplanes	( SCGCQ01349936 port of SCGCQ01349247) 
 - IOP: MCTP: Firmware stops freeing posted PCIe credit	( SCGCQ01353719 port of SCGCQ01345810) 
 - Ventura: PL FW may fault x720E for invalid backplane type configuration	( SCGCQ01357973 port of SCGCQ01351358) 
 - Ventura: PL FW may fault x720E for invalid backplane type configuration	( SCGCQ01357974 port of SCGCQ01351358) 
 - ExpressSDS: Add a new event MR_EVT_PD_INQUIRY_INFO to log device Inquiry info on discovery at SOD, or device insertion	( SCGCQ01368290 port of SCGCQ00880746) 
 - EXSDS : RAID 0 ,1 Config created in raid mode are not imported after personality switch when > 64 UG drives are connected .	( SCGCQ01368326 port of SCGCQ00906370) 
 - SDS:Adapter at Base Port not responding when background operations running reboot the system	( SCGCQ01368364 port of SCGCQ00926900) 
 - MR_Invader_eSDS_CISCO: Not able to create EPD using storcli.	( SCGCQ01368400 port of SCGCQ00944454) 
 - VD LEDs are not updated if SES Monitoring is disabled	( SCGCQ01368431 port of SCGCQ01004444) 
 - eSDS_1.1:Firmware crash@line 108 in file ../../raid/taskman.c when performing creation and deletion of EPD's	( SCGCQ01370440 port of SCGCQ01023898) 
 - ExpressSDS: Firmware crashes during hibernation	( SCGCQ01370487 port of SCGCQ01042005) 
 - Improve Error Reporting for SPI flash commands.	( SCGCQ01372977 port of SCGCQ01358446) 
 - SATA: Block device log pages does not free the Raw frames	( SCGCQ01373423 port of SCGCQ01373403) 
 - Found invalid event	( SCGCQ01375911 port of SCGCQ01347858) 
 - SSU Commands to SPL-2 compliant drive times out	( SCGCQ01376408 port of SCGCQ01358769) 
 - PL: RETURNED LOGICAL BLOCK ADDRESS in READ CAPACITY (16	( SCGCQ01377235 port of SCGCQ01366977) 
 - Chassis slot valid bit is not set into Enclosure Page 0.	( SCGCQ01380979 port of SCGCQ01323680) 
 - PL:Customer specific drive enumeration	( SCGCQ01380981 port of SCGCQ01198341) 
 - Chassis slot valid bit is not set into Enclosure Page 0.	( SCGCQ01380982 port of SCGCQ01323680) 
 - PL : Drives may not spin up due to bug in spin up path found during code walk through	( SCGCQ01385320 port of SCGCQ01358138) 
 - MR 7.3 :PL Fault 0000d075 LR 01283991 , while running IO`s , CC and OCR in background.	( SCGCQ01399528 port of SCGCQ01384714) 
 - Feature to retrieve the TTY logs compressed	( SCGCQ01400363 port of SCGCQ00772215) 
 - PL: IT Nexus Reset Option for Avoid Duplicate Mid Feature	( SCGCQ01401592 port of SCGCQ01362788) 
 - (SATA Only	( SCGCQ01409312 port of SCGCQ01406046) 
 - MR7.1: Shutdown command received from host" missed in tty log	( SCGCQ01410916 port of SCGCQ01389941) 
 - Restore nvram flag allowOnlineCtrlReset after set factory default completes	( SCGCQ01411041 port of SCGCQ01378753) 
 - Boot message string change for BOOT_MSG_CACHE_DISCARD	( SCGCQ01412801 port of SCGCQ01394348) 
 - Parameter Page Reads fail during ONFI bringup.	( SCGCQ01413784 port of SCGCQ01413557) 
 - Parameter Page Reads fail during ONFI bringup.	( SCGCQ01415127 port of  SCGCQ01413557) 
 - PL: Change nvdata bits for avoid duplicate mid feature to Mfg 17 Flags bits 12:11	( SCGCQ01421336 port of SCGCQ01414932) 
 - PL: Change avoid duplicate mid LUN reset option to abort task set	( SCGCQ01429867 port of SCGCQ01429655) 
 - Ventura VSES: Unique id and serial number for virtual SES to support microsoft storage spaces direct.	( SCGCQ01436959 port of SCGCQ01404241) 
 - Assertion failure in ../../raid/buffer.c for offline R6 Logical drives by Removing the drives while IO.	( SCGCQ01441338 port of SCGCQ01358905) 
 - Ventura vSES: SAS and SATA direct attached devices are not getting associated to vSES in Windows Storage Spaces Direct.	( SCGCQ01442629 port of SCGCQ01438119) 
 - Not able to add drives to existing R10 VD	( SCGCQ01446112 port of SCGCQ01240761) 
 - Bugzila 112779 - [PM863A SSD can not show the "Part Number"/ "FRU Number" information under Host tool web w	( SCGCQ01448010 port of SCGCQ01435624) 
 - BSt Ventura 7.5 Profile21==> Set Drive Offline Failed.	( SCGCQ01448671 port of SCGCQ01437184) 
 - Add support for Transport Ready in Ventura	( SCGCQ01454814 port of SCGCQ01387369) 
 - MCTP I2C: I2C communication is lost between BMC and controller	( SCGCQ01455876 port of SCGCQ01385782) 
 - PL : PWR_GRANT is not issued upon PWR_REQ from SPL2 drive	( SCGCQ01458074 port of SCGCQ01330984) 
 - PL: EnclMgmt: Move ownership of SES Page 0x0A slot mapping from devices to PHYs	( SCGCQ01458622 port of SCGCQ00870423) 
 - PL : PL fault 0x7C72 is hit during discovery when disabling and enabling all the PHYs connected to legacy SAS drives	( SCGCQ01458664 port of SCGCQ01455200) 
 - ONFI Device param page checksum calculation is not correct.	( SCGCQ01460622 port of SCGCQ01460478) 
 - NVMe drive discovery fails after pull/push on customer specific NVMe supported backplane	( SCGCQ01460735 port of SCGCQ01404209) 
 - Ventura B0: NVME Drives Not Discovered on 16i Card	( SCGCQ01461753 port of SCGCQ01381033) 
 -	( SCGCQ01462850 port of SCGCQ01459442) 
 - MR7.4 Alpha shows, MS- Jetstress 12% DB Read Performance Regression with Single Driver R0 ( 24VDs	( SCGCQ01463243 port of SCGCQ01448858) 
 - Hot plugged NVMe drive fails to link up on OEM backplanes with ISTWI drive presence polling enabled	( SCGCQ01464096 port of SCGCQ01463496) 
 - MR 7.4 - COL hit Assertion mon_task	( SCGCQ01464512port of SCGCQ01452209) 
 - MR7.4: LDs disappear when changing controller profile (from profile 10 back to profile 12	( SCGCQ01465007 port of SCGCQ01413560) 
 - Disable combined Reply mode for MSIx if MCTP is enabled	( SCGCQ01466073 port of SCGCQ01459283) 
 - Fast Path IO is not failed for LDBBM table entries	( SCGCQ01466376 port of SCGCQ01452385) 
 - Fixed the issue with older ibutton	( SCGCQ01466737 port of SCGCQ01455738) 
 -	( SCGCQ01466917 port of SCGCQ01346550) 
 - System will pop up “Cannot communicate with iButton to …” during reboot with customer iMR card (FW:50.2.1-0597	( SCGCQ01467155 port of SCGCQ01447988) 
 - Single Thread MSI-X and MCTP accesses	( SCGCQ01467163 port of SCGCQ01446273) 
 - Limit printing a SGL chain to only 15 elements.	( SCGCQ01468156 port of SCGCQ01180961) 
 - 8GB DDR support Changes for seamless downgrade/upgrade of MR FW pkgs	( SCGCQ01472902 port of SCGCQ01415141) 
 - Storclif Restart command fails with ERRCd 105	( SCGCQ01472919 port of SCGCQ01461663) 
 - I2C controller hang is observed with repeated LD create and delete script from BMC	( SCGCQ01473774 port of SCGCQ01378552) 
 - Max supported disk of Raid 50 and Raid 60 is showing 138	( SCGCQ01474118 port of SCGCQ01472877) 
 - OEM intruder: Error scrolls on debugger:C0:EnclSgpioHandleDevicePresenceCallback:should never happen logic/internal error.	( SCGCQ01474296 port of SCGCQ01235177) 
 - 930-16i Cannot Spinup HDD During System Power On	( SCGCQ01477277 port of SCGCQ01470741) 
 - PL: Add Code to Correctly Determine Mid for Rx Context Non-automated Interrupts	( SCGCQ01479502 port of SCGCQ01472512) 
 - Purley Server: CATERR reported on front panel LCD and SUT hang at the windows logo page	( SCGCQ01481033 port of SCGCQ01410221) 
 - Purley Server: CATERR reported on front panel LCD and SUT hang at the windows logo page	( SCGCQ01481034 port of SCGCQ01410221) 
 - MR RAID-mode profile 10 create vd cause pds for that vd offline	( SCGCQ01481312 port of SCGCQ01450092) 
 - 9460-8i card connect drive through direct-attached backplane: error LED not on when drop out a drive.	( SCGCQ01482233 port of SCGCQ01445040) 
 - Factory default restore required to set the controller properties after FW upgrade	( SCGCQ01483186 port of SCGCQ01479667) 
 - Target device LED issues on Talladega slot #25	( SCGCQ01483718 port of SCGCQ01394459) 
 - Change stot status for SGPIO rebuilding drive when drive becomes offline/failed.	( SCGCQ01484109 port of SCGCQ01208452) 
 - System will pop up “Cannot communicate with iButton to …” during reboot with OEM custom card	( SCGCQ01496768 port of SCGCQ01501209) 
 - Switching back and forth between profile 10 and 12 with data cable pull results in foreign config not importable	( SCGCQ01501951 port of SCGCQ01485045) 
 - IOP: 0x265D Fault Observed on Cold Boot of Customer Server with Misconfigured Controller NVDATA	( SCGCQ01505077 port of SCGCQ01473138) 
 - PL SATL: SCSI Write Buffer Mode 7 Command Incorrectly Failed by Firmware	( SCGCQ01505080 port of SCGCQ01498114) 
 - IOP: I2C MCTP: Slave response mode fails to return response to I2C read	( SCGCQ01508067 port of SCGCQ01506883 ) 
 - Controller hangs after warm reboot in presence of pinned cache	( SCGCQ01508156 port of SCGCQ01497790) 
 - Preserved Cache doesn't flush back during Foreign Import	( SCGCQ01510341 port of SCGCQ01466831) 
 - MR7.3.1 : controller reset seen while importing 32 VD foreign config	( SCGCQ01511969 port of SCGCQ01506874) 
 - Fault State (0x265d	( SCGCQ01514262 port of SCGCQ00856085) 
 - iMR-FW Drive Fault LED will light at some frequency when a JBOD drive is pulled out	( SCGCQ01516692 port of SCGCQ01481393) 
 - pl: backend PCIe: workaround timer may trigger after too short of an interval	( SCGCQ01519802 port of SCGCQ01518343) 
 - pl: NVMe: rapid device removal/add with a specific vendor backplane	( SCGCQ01522511 port of SCGCQ01487423) 
 - pl: backend PCIe: 4311 fault with NVMe enabled (part 2	( SCGCQ01523550 port of SCGCQ01523531) 
 - pl: backend PCIe: non-NVMe endpoint not cleaned up on removal	( SCGCQ01529383 port of SCGCQ01516968) 
 - PL: Fault 0x5862 seen when host buffer size is smaller than allocation length in CDB	( SCGCQ01529512 port of SCGCQ01509770) 
 - 7.6 NVDATA change for NVMeAbortTO in MrParamsPage0, and correct MrParamsPage0 XSD mapping.	( SCGCQ01533324 port of SCGCQ01531782) 
 - Sles12 SP3 OS is getting stuck during first boot	( SCGCQ01538948 port of SCGCQ01531741) 
 - PL Fault 0000ecdd LR 01403837 during initial discovery	( SCGCQ01539840 port of SCGCQ01531770) 
 - Initiate ocr when FW enters MonTask	( SCGCQ01540255 port of SCGCQ01381615) 
 - MR7.1/7.3 Termlog/UARTlog - messages sometimes missed in Termlog	( SCGCQ01540360 port of SCGCQ01498188) 
 - pl: backend PCIe: switch attached discovery takes too long	( SCGCQ01556426 port of SCGCQ01522343) 
 - memory leak issue resulting controller crash	( SCGCQ01561900 port of SCGCQ01539353) 
 - Jbod become Ugood sometimes after reboot	( SCGCQ01561914 port of SCGCQ01508978) 
 - Controller hung, when updating the drive firmware	( SCGCQ01562034 port of  SCGCQ01553266) 
 - Performance Improvements	( SCGCQ01562098 port of SCGCQ01455538) 
 - heck Consistency doesn't identify double media errors once aborting and starting CC again	( SCGCQ01567485 port of SCGCQ01411591) 
 - MR7.3.1_Assertion failure in ../../dma/dmaxor.c at line 1180:	( SCGCQ01574072 port of SCGCQ01482384) 
 - System hangs after performed Cryptographic Erase on SAS ISE drive	( SCGCQ01574395 port of SCGCQ01525119) 
 - pl: backend PCIe: 4311 fault (part 3	( SCGCQ01574924 port of SCGCQ01537791) 
 - MR 7.6 Assertion failure in ../../dm/src/dm.c at line 1540: 0" after pwr off the enclosure to generate pinned_cache	( SCGCQ01579752 port of SCGCQ01561611) 
 - Turn off GPIOA19 (global fault LED installed	( SCGCQ01581266 port of SCGCQ01566616) 
 - Fixing the issues during bringup of the universal backplane.	( SCGCQ01581911 port of SCGCQ01522148) 
 - To fix issues for back plane configuration validation and LED control for the UBM backplane.	( SCGCQ01582240 port of SCGCQ01533852) 
 - To fix the LED issue, VPP data and moving to change detect poll state	( SCGCQ01582246 port of SCGCQ01576165) 
 - Event with enclose 0x00 slot 0 during the system boot when a command is timed out (Command timeout on PD 12(e0x00/s0	( SCGCQ01582497 port of SCGCQ01520443) 
 - STP Passthru commands end up with blank FiS response buffer	( SCGCQ01582503 port of SCGCQ01576179) 
 - 9460-8i is reporting Chip Temperature of 255 when the ambient temp is about 0 C	( SCGCQ01582535 port of SCGCQ01565568) 
 - Ventura B0: Slot status LED updates to certain slots on NVMe backplane may fail	( SCGCQ01598554 port of SCGCQ01574224) 
 - Restrict FW update based on NVMe external clock oscillator support of current SBR and inbound SBR image (Talladega and Martinsville ONLY	( SCGCQ01599743 port of SCGCQ01593696) 
 - Enclosures is not exposed to Host even if exposeEnclosureToHost is set.	( SCGCQ01615762 port of SCGCQ01599832) 
 - To implement the CHANGE_DETECT GPIO feature for the UBM backplanes	( SCGCQ01628439 port of SCGCQ01507506) 
 - The PCIe reset to be handled properly for the Change detect feature	( SCGCQ01628451 port of SCGCQ01623437) 
 - PL: Change to Customer Specific SMP Response Report Manufacturer	( SCGCQ01641073 port of SCGCQ01505468) 
 - Not all NVMe drives were discovered after server cold or warm boot	( SCGCQ01686240 port of SCGCQ01664963) 
 - (SATA only	( SCGCQ01720496 port of SCGCQ01681441) 
 -	( SCGCQ00136970 port of SCGCQ00126592) 
 - IR Firmware: Data Corruption for virtual read seen while failing a resyncing RAID10 volume	( SCGCQ00138314 port of SCGCQ00135147) 
 - Fault 265D occurs when running IOs to volume which has 1 drive connected via cable breaker & 1 direct attached,to HBA.	( SCGCQ00150517 port of SCGCQ00147098) 
 - IR MP: Fault 8405 encountered if resyncing disks is removed.	( SCGCQ00150519 port of SCGCQ00140613) 
 - LSI2008 SATA NCQ enablement	( SCGCQ00153474 port of SCGCQ00142855) 
 - Bit 20 of RAID Volume Page 0 to comply with definition as in MPI 2 spec rev M or later	( SCGCQ00153681 port of SCGCQ00145313) 
 - IOP: First DNS lookup for a TFTP Server fails in Ethernet Firmware Download	( SCGCQ00153863 port of SCGCQ00147385) 
 - IOP: Xmodem commands hang when IOC is in Fault state	( SCGCQ00154747 port of SCGCQ00149111) 
 - IOP: Ethernet firmware download sometimes completes successfully, then faults	( SCGCQ00154866 port of SCGCQ00146094) 
 - Send Execute Device Diagnostic ATA command during SATA Initialization	( SCGCQ00155108 port of SCGCQ00148227) 
 - (IOP-Only	( SCGCQ00155283 port of SCGCQ00128289) 
 - MPI2: prepare 02.00.17 header files	( SCGCQ00156016 port of SCGCQ00150068) 
 - Eliminate PL Config Page restrictions	( SCGCQ00157819 port of SCGCQ00143162) 
 - CKE signal in Memory subsystem glitches when entering self refresh mode	( SCGCQ00159096 port of SCGCQ00153284) 
 - Utility: Update IO Unit page 1 reference in memcfg utility	( SCGCQ00160080 port of SCGCQ00153751) 
 - USB: Create a package build	( SCGCQ00160111 port of SCGCQ00151517) 
 - DMA sense data with FW instead of HW to prevent a hang of the DMA transfer.	( SCGCQ00160363 port of SCGCQ00155280) 
 - Setting the Min and Max value for the resources in Mfgpag9 to ffff leads to fwfault 0x0302	( SCGCQ00160405 port of SCGCQ00153253) 
 - Fault 5803 during discovery of large topology after adjusting Ph8 Alpha FW NVDATA on Liberator B4.	( SCGCQ00162377 port of SCGCQ00155755) 
 - (IOP	( SCGCQ00163614 port of SCGCQ00152500) 
 - USB: Enumeration somestime causes fault 0xD04	( SCGCQ00164452 port of SCGCQ00151004) 
 - Host and Library API names to contain 'i' to denote interfacing API.	( SCGCQ00164491 port of SCGCQ00155949) 
 - 265d fault is seen when volume member drives are removed & inserted simultaneously	( SCGCQ00165921 port of SCGCQ00154633) 
 - Trying to flash IR firmware image on a controller with no NVSRAM faults with 265D fault code	( SCGCQ00165922 port of SCGCQ00158423) 
 - Rescaning of large topology with 90 drives during make and break of wide port not handled properly by driver	( SCGCQ00165923 port of SCGCQ00146928) 
 - Hot Spare not getting pulled in after removing a member drive from IM volume	( SCGCQ00165924 port of SCGCQ00156138) 
 - With the failed RAID10 volume after removing two adjacent drives the BGI is still in progress	( SCGCQ00169770 port of SCGCQ00166640) 
 - IR: BGI stalls during when Raid1 volume drives are >2TB	( SCGCQ00172673 port of SCGCQ00169172) 
 - Gemini not correctly enabling the upper GPIOs	( SCGCQ00174442 port of SCGCQ00156991) 
 - IR: Tape drive reported as non-certified drive	( SCGCQ00174932 port of SCGCQ00166084) 
 - Comment out UART FIFO toggle	( SCGCQ00177378 port of SCGCQ00176249) 
 - Ringbuffer corrupted when exception data printed after a fault	( SCGCQ00177379 port of SCGCQ00175209) 
 - DDR3 Fails Training On Some Hardware	( SCGCQ00177382 port of SCGCQ00172188) 
 - (NVDUMP	( SCGCQ00177563 port of SCGCQ00162939) 
 - Format ringbuffer prints for I2C	( SCGCQ00178836 port of SCGCQ00175655) 
 - Disable/enable of the Fast Path Engine for a device was not working.	( SCGCQ00184821 port of SCGCQ00182860) 
 - RAID1 volume turns to failed state after swapping the primary & secondary drives with each other with hot spares present	( SCGCQ00186468 port of SCGCQ00170472) 
 - IR: Multiple simultaneous drive pulls can lead to an adapter reset	( SCGCQ00186470 port of SCGCQ00170872) 
 - Enhance Gen2 IR firmware to actually issue the START/STOP UNIT command to SATA SSD volume members	( SCGCQ00188492 port of SCGCQ00162019) 
 - Need generic IOP method to read and write from indirect window in our chips	( SCGCQ00188773 port of SCGCQ00125084) 
 - Event notification for NOTIFY(Enable Spinup	( SCGCQ00188779 port of SCGCQ00161993) 
 - XSD files update for MPI config page addition and man page changes.	( SCGCQ00190956 port of SCGCQ00179240) 
 - (SRIOV BLD	( SCGCQ00201445 port of SCGCQ00176720) 
 - (SRIOV-Only PL	( SCGCQ00201464 port of SCGCQ00176747) 
 - (SRIOV-Only	( SCGCQ00201728 port of SCGCQ00176741) 
 - (SRIOV	( SCGCQ00201837 port of SCGCQ00152257) 
 - (SRIOV IOC	( SCGCQ00202178 port of SCGCQ00176721) 
 - (SRIOV	( SCGCQ00202316 port of SCGCQ00152258) 
 - (SRIOV-Only PL	( SCGCQ00203026 port of SCGCQ00176746) 
 - DDR3: Read leveling delay issue on slow skew hardware	( SCGCQ00203649 port of SCGCQ00193395) 
 - Drive not shownup in linux after insertion to a hot slot to an incompatible volume	( SCGCQ00203887 port of SCGCQ00193963) 
 - iButton authorization requirment not enabled on SRIOV build by default	( SCGCQ00204102 port of SCGCQ00188480) 
 - Update to handle large out of range max host credit setting in manufacturing page 9.	( SCGCQ00204203 port of SCGCQ00186348) 
 - (IOP-Only	( SCGCQ00204304 port of SCGCQ00183882) 
 - UART CLI command to erase a region of IOC Flash ROM	( SCGCQ00206284 SCGCQ00173641) 
 - Hardware does not detect all errors in PCI received packets	( SCGCQ00209345 port of SCGCQ00198832) 
 - PL: Slot number in Device Page 0 may be incorrect	( SCGCQ00218355 port of SCGCQ00193383) 
 - change batch file to modify permissions of zip file so web build / release gets updated zip file	( SCGCQ00225823 port of SCGCQ00225815) 
 - (IOP-Only	( SCGCQ00226692 port of SCGCQ00204180) 
 - IR: Resync operation for RAID10 volume stalls when 13% complete	( SCGCQ00235599 port of SCGCQ00192089) 
 - Child: Add PI to IR: Metadata changes	( SCGCQ00235602 port of SCGCQ00204629) 
 - PI Enable flag on manufacturing page 10 is ignored on activation	( SCGCQ00235655 port of SCGCQ00216422) 
 - RAID Volume degraded after roaming	( SCGCQ00235659 port of SCGCQ00218013) 
 - Child: Add PI to IR: RAID Passthrough Messages	( SCGCQ00237154 port of SCGCQ00194035) 
 - Child: Add PI to IR: Error Logging	( SCGCQ00237166 port of SCGCQ00204612) 
 - Set firmware to fault at boot loader if IR is enabled and NVSRAM is missing	( SCGCQ00237344 port of SCGCQ00173439) 
 - The SATL's inquiry VPD page 0 doesn't show support for block limits and logical block provisioning pages.	( SCGCQ00237489 port of SCGCQ00226980) 
 - Child: Add PI to IR: BGI Changes - Initialize PI Info	( SCGCQ00237709 port of SCGCQ00194014) 
 - Logical block reference tag errors on host IOs	( SCGCQ00237896 port of SCGCQ00223337) 
 - Improve the performance of adaptive heuristic queue depth algorithm.	( SCGCQ00238404 port of SCGCQ00226755) 
 - Mixing of PI type 2 formatted drives and non-PI drives results in error creating RAID volume	( SCGCQ00243894 port of SCGCQ00240457) 
 - BIOS CU might display dual path during RAID creation on a OEM specific config	( SCGCQ00246965 port of SCGCQ00218145) 
 - Disabling PHY's through SAS IO Unit Page 1 might stop Heartbeat LED blinking	( SCGCQ00249386 port of SCGCQ00221519) 
 - (IOP-Only	( SCGCQ00254515 port of SCGCQ00202274) 
 - Custom HARD RESET behavior in Target Mode firmware	( SCGCQ00255664 port of SCGCQ00198846) 
 - Add UART command to write host/system/PCI memory	( SCGCQ00257564 port of SCGCQ00227930) 
 - SATL: Configurable Write Same execution behavior	( SCGCQ00260442 port of SCGCQ00245759) 
 - Tbolt: Port width modulation changes	( SCGCQ00261551 port of SCGCQ00165936) 
 - LWIP (Ethernet library	( SCGCQ00270264 port of SCGCQ00269923) 
 - Fault 0x2651 on a Message Unit Reset (MUR	( SCGCQ00279907 port of SCGCQ00245940) 
 - Host IO uses PI on volume where BGI is pending	( SCGCQ00280128 port of SCGCQ00243939) 
 - Fix formatting of iopMsgHandlerPortEnable(	( SCGCQ00280172 port of SCGCQ00242056) 
 - RAID1 Volume fails to start resync when a hot plugged hot spare is available	( SCGCQ00293807 port of SCGCQ00229135) 
 - Raid Accelerator IOs hang with injected Guard Errors or when running Multi-threaded IOs	( SCGCQ00294585 port of SCGCQ00279629) 
 - Always flush secondary column write cache during resync regardless of whether volume write cache is enabled or not.	( SCGCQ00305738 port of SCGCQ00277798) 
 - 32MB flash chips support	( SCGCQ00307946 port of SCGCQ00229730) 
 - (DDR3	( SCGCQ00314699 port of SCGCQ00250014) 
 - Example NVDATA files to enable support for operation at 1333MT/s and other supported speeds for SAS2208 devices	( SCGCQ00314702 port of SCGCQ00234416) 
 - SAS2308 doesn't support DPO or FUA	( SCGCQ00320040 port of SCGCQ00254531) 
 - BIOS Page 1 default for BIOSOptions and UEFIVersion need updated	( SCGCQ00320044 port of SCGCQ00258821) 
 - SAS2 FW:Ph14:Spelling Mistakes in UART Iop erflsh command help	( SCGCQ00320049 port of SCGCQ00280467) 
 - DDR3: False positive fault while finding read latency.	( SCGCQ00335417 port of SCGCQ00194835) 
 - (DDR3	( SCGCQ00385281 port of SCGCQ00225383) 
 - MPI2 Toolbox - Memory Move Tool - does not transfer data as expected	( SCGCQ00440476 port of SCGCQ00210057) 
 - PL: Event Replay device reordering	( SCGCQ00469721 port of SCGCQ00313918) 
 - Controller firmware could not decode the correct reference clock speed other than 150 MHz	( SCGCQ00469801 port of SCGCQ00343999) 
 - Enhanced PLI Control Request Interface	( SCGCQ00471944 port of SCGCQ00354301) 
 - (IOP	( SCGCQ00471990 port of SCGCQ00384769) 
 - PCI information contains wrong device ID for Fury(3008	( SCGCQ00472414 port of SCGCQ00356996) 
 - (IOP	( SCGCQ00472494 port of SCGCQ00391442) 
 - ISTWI support to handle zero length transfer read and write requests	( SCGCQ00472602 port of SCGCQ00301262) 
 - Ensure debug information tools work during fault	( SCGCQ00472607 port of SCGCQ00339781) 
 - (IOP	( SCGCQ00472610 port of SCGCQ00267257) 
 - ONFI: Add new diag commands	( SCGCQ00473932 port of SCGCQ00349860) 
 - Added faults in the cable management code	( SCGCQ00473937 port of SCGCQ00365524) 
 - IOP:MSI/ MSIx error interrupt is not handled	( SCGCQ00474084 port of SCGCQ00378041) 
 - (IOP	( SCGCQ00475369 port of SCGCQ00377971) 
 - DDR: IOP: Code copy causes a TLB error interrupt	( SCGCQ00475371 port of SCGCQ00375411) 
 - IOP: Fault 0x1500 encountered when using Invader C0 on some systems using MSIx	( SCGCQ00476786 port of SCGCQ00374927) 
 - Serdes temperature sensitivity may cause phy errors	( SCGCQ00476793 port of SCGCQ00384936) 
 - Prevent access to PCIe core PLB registers until clock is stable	( SCGCQ00476821 port of SCGCQ00364546) 
 - Create SAS3 XML bindings file for NVDATA Cloud App	( SCGCQ00477174 port of SCGCQ00379940) 
 - Firmware faults with 0x2622 due to a parity error in pad (unused	( SCGCQ00477177 port of SCGCQ00332124) 
 - Extend FLASH Erase Timeout for Future chips	( SCGCQ00504709 port of SCGCQ00504060) 
 - Invader C0: Minor Target mode optimzations	( SCGCQ00551042 port of SCGCQ00411657) 
 - (IOP	( SCGCQ00552450 port of SCGCQ00383875) 
 - IOP: Reply queue hardware not reset on IOC Init after message unit reset	( SCGCQ00552457 port of SCGCQ00384570) 
 - BST : 265D fault while flashing the IT/IR images over Falcon and Liberator and Meteor IT.	( SCGCQ00553447 port of SCGCQ00298671) 
 - make internal temperature sensor data available at start-of-day	( SCGCQ00559404 port of SCGCQ00419450) 
 - Set DPC bit in CCR1 inside GHS flash scripts	( SCGCQ00559717 port of SCGCQ00403127) 
 - IOP: 0x2628 faults from Gen HS FIFO 1	( SCGCQ00563314 port of SCGCQ00426490) 
 - IOP: SRIOV passes error when modifying visibility for DevHandles greater than 30	( SCGCQ00563456 port of SCGCQ00439499) 
 - Definition of SAS Clock Override field was incorrect	( SCGCQ00563901 port of SCGCQ00399250) 
 - IOP: Asynchronous reset may cause system reset and PCIe link down	( SCGCQ00564387 port of SCGCQ00421011) 
 - IOP: Value of PCIe SERDES parameter causes less than optimal receiver margin	( SCGCQ00565464 port of SCGCQ00400449) 
 - IOP: MCTP Event Handling	( SCGCQ00565513 port of SCGCQ00400534) 
 - IOP: Events not received by the host	( SCGCQ00566087 port of SCGCQ00403436) 
 - In iopDiagCmdPerfMonPlbAdd the string plbadd needs to be changed to addl2 to better describe the cli command	( SCGCQ00566125 port of SCGCQ00457390) 
 - HW Issue Needs Workaround - PCIe Link Equalization Request Bit in Link Status 2 Reg Not Cleared After Writing 1	( SCGCQ00566144 port of SCGCQ00461420) 
 - IOP: RAID Accelerator may not set up snooping registers correctly	( SCGCQ00566147 port of SCGCQ00461790) 
 - Standard Inquiry Data - Change Version Descriptor 2 to SAT-3	( SCGCQ00566190 port of SCGCQ00521576) 
 - IOP: Enable MCTP support in IT/IR firmware.	( SCGCQ00566207 port of SCGCQ00396012) 
 - IOP: Add System Management configuration page	( SCGCQ00566211 port of SCGCQ00404227) 
 - PL: Update Host Based Discovery to include DataBolt settings	( SCGCQ00566213 port of SCGCQ00414622) 
 - IOP: MCTP: Add Slave-response-mode operation support	( SCGCQ00566226 port of SCGCQ00450123) 
 - Check if Power On Sense option is valid at SOD	( SCGCQ00566232 port of SCGCQ00472368) 
 - Build process improvements	( SCGCQ00566244 port of SCGCQ00477137) 
 - mpi_temp.h cleanup	( SCGCQ00568424 port of SCGCQ00503059) 
 - Turn on Allow Table-to-Table Links bit in SAS IO Unit Page 1 in default NVDATA.	( SCGCQ00568467 port of SCGCQ00339375) 
 - Configurable SES Page Buffer Size	( SCGCQ00568488 ) 
 - SAS2 IT - Phase 17 – WRITE LONG(16	( SCGCQ00568499 ) 
 - SCSIStatusQualifier is added to SCSI IO Error Reply	( SCGCQ00568504 port of SCGCQ00397520) 
 - IOP: MCTP: Response to MR Cmd returns MR Cmd PayloadID, return SCS Cmd PayloadID	( SCGCQ00568510 port of SCGCQ00565690) 
 - Fury no longer links up to Maxim expander with phase 2 FW	( SCGCQ00596630 port of SCGCQ00525026) 
 - Resolve the build errors for the Phase4.0 Pre-Alpha release	( SCGCQ00596631 port of SCGCQ00567486) 
 - GenCRC utility incorrectly calculates the image size internally	( SCGCQ00692023 port of SCGCQ00564201) 
 - IOP: MSIX Index in MID Descriptor not always set appropriately	( SCGCQ00725179 port of SCGCQ00580302) 
 - Pli Control Request for IOP to Bypass FP disable on Selected Device Handle in Target Mode Based PL upon receipt of for non good response frame	( SCGCQ00725182 port of SCGCQ00568651) 
 - SAS3 SCS IT/IR firmware fails to hostboot	( SCGCQ00725188 port of SCGCQ00695527) 
 - Remove event replay macro from mpi_temp.h file	( SCGCQ00725196 port of SCGCQ00574398) 
 - SAS phy page 3 write current action does not take effect immediately	( SCGCQ00725250 port of SCGCQ00602005) 
 - IOP: PowerPC ITLB Miss Errata with Pre-fetch using start of TLB padding	( SCGCQ00725262 port of SCGCQ00672307) 
 - Add ability to control ContinueAWT	( SCGCQ00725279 port of SCGCQ00530872) 
 - Remove unnecessary #if and duplicate function prototype	( SCGCQ00725303 port of SCGCQ00644368) 
 - SATL: Indicate support for the ATA Device Server Password security protocol	( SCGCQ00725310 port of SCGCQ00465302) 
 - IOP: MCTP: MCTP Control Discovery Notify over PCIe may be transmitted before host enables PCIe messages	( SCGCQ00725329 port of SCGCQ00663155) 
 - SCSI Command is Not Failed with Expected Response When Reserved Fields Set as Non-Zero Value for SATA Disk Under Format	( SCGCQ00725333 port of SCGCQ00679566) 
 - Support for Power Management States still advertised in PCIe DPA Configuration Regsiter when FW does not support	( SCGCQ00725340 port of SCGCQ00681116) 
 - IOP: PCIe DPA Status Configuration Register does not default to zero after a link down	( SCGCQ00725350 port of SCGCQ00663176) 
 - IOP: One path to freeing recevied generic PCIe messages is optimized out	( SCGCQ00725368 port of SCGCQ00660285) 
 - IOP: SR-IOV: Config page access denied from VFs	( SCGCQ00725373 ) 
 - IOP MCTP: Add basic MCTP Control Commands	( SCGCQ00725379 ) 
 - IOP MCTP: MPI Event registration, Extended Events command, and transmitting event datagrams	( SCGCQ00725380 port of SCGCQ00620227) 
 - IOP MCTPMsg: Add MPI RAID Action and RAID SCSI IO Passthrough	( SCGCQ00725385 port of SCGCQ00620222) 
 - Temperature Monitoring with bi-colored LED and over temp faulting.	( SCGCQ00725386 port of SCGCQ00577387) 
 - (DDR3	( SCGCQ00733051 ) 
 - Add support for zero length FLASH layout regions	( SCGCQ00764176 ) 
 - Add axTLS license file	( SCGCQ00781301 ) 
 - IOP: SR-IOV: Phy Changed events improperly filtered from SAS Topology Change List Event	( SCGCQ00781310 port of SCGCQ00683190) 
 - SRIOV IT: SAS Topology Change List Event data has entries for devices which are not mapped to the VFs	( SCGCQ00781329 port of SCGCQ00706800) 
 - IOP: SR-IOV: VF access to BIOS pages unexpectedly restricted	( SCGCQ00781342 port of SCGCQ00713442) 
 - IOP: Firmware download of complete flash could access invalid array index	( SCGCQ00781356 port of SCGCQ00728155) 
 - IOP: Memory move operation could access uninitialized variables	( SCGCQ00781357 port of SCGCQ00728677) 
 - IOP: Performance monitor CLI command could cause invalid array access	( SCGCQ00781365 port of SCGCQ00729619) 
 - IOP SRIOV: During controller boot-up, make PortEnable replies to VFs wait until PF is ready	( SCGCQ00781386 port of SCGCQ00689555) 
 - IOP: MCTP: Register for events to filter without asynchronous event datagram	( SCGCQ00781390 port of SCGCQ00699048) 
 - PL: Enclosure management code doesn't check return value	( SCGCQ00793928 port of SCGCQ00749722) 
 - IOP: Allow Fault Indication Function Code to override other GPIOs	( SCGCQ00793948 port of SCGCQ00741953) 
 - IOP: MCTP: Send busy retry status for response retransmission when no response is available	( SCGCQ00793951 port of SCGCQ00760431) 
 - Intruder: (IOP	( SCGCQ00801682 port of SCGCQ00707767) 
 - IOP: MCTP function only returns failure	( SCGCQ00816412 port of SCGCQ00787481) 
 - IOP: Poor coding style hides variable	( SCGCQ00816418 port of SCGCQ00787474) 
 - Fix compilation options	( SCGCQ00816426 port of SCGCQ00788656) 
 - DDR: Eliminate requirement in layout checklist to have clk be 1 inch longer than DQS	( SCGCQ00831257 port of SCGCQ00800434) 
 - Fixed the occurance of fault 0x1708, when a free MID is attempted to be failed to the host.	( SCGCQ00848143 port of SCGCQ00810649) 
 - IOP/IR: MCTP: After Volume Creation, no other commands can be executed	( SCGCQ00848197 port of SCGCQ00848197) 
 - IOP: MCTPMsg: Async events not always held back when not enabled	( SCGCQ00848202 port of SCGCQ00848202) 
 - Updated Comments in Fault and LogInfo Files	( SCGCQ00851631 port of SCGCQ00824577) 
 - SBL Bus not supported for I2C slave operations	( SCGCQ00851641 port of SCGCQ00810020) 
 - No boundary on I2C slave operations	( SCGCQ00851642 port of SCGCQ00810110) 
 - Initialization with BMC using I2C and slave response mode failed after moving from Phase 4 to Phase 6	( SCGCQ00855346 port of SCGCQ00831952) 
 - IOP: MCTP: Reinitalizing SLIR3-MCTP many times causes CmdStatus Busy to always be sent back in response	( SCGCQ00873958 port of SCGCQ00864752) 
 - IOP: Add code to stop additional hardware upon adapter reset	( SCGCQ00890618 port of SCGCQ00883655) 
 - (IOP	( SCGCQ00894197 port of SCGCQ00874061) 
 - NVDATA: Modify Manufacturing Page 30 Default NVDATA	( SCGCQ00927357 port of SCGCQ00925761) 
 - NVDATA: Fix overtemp LED for channel cards	( SCGCQ01004877 port of SCGCQ00924428) 
 - IOP: Fast Path SATA IO disappears and causes timeout and 6001 fault	( SCGCQ01004888 port of SCGCQ00943874) 
 - Intruder: Change "A0" to "A1" in comments of channel NVDATA files	( SCGCQ01004906 port of SCGCQ00889812) 
 - PL: I/O timeout while running both auto and non-auto I/Os.	( SCGCQ01025036 port of SCGCQ01022368) 
 - CFGI: CFGI Library to expose the variable gCfgiFlashAvailable that needs to be set by IOP	( SCGCQ01058158 ) 
 - Config write request validation adjusted to page header size as the minimum request length	( SCGCQ01197348 ) 
 - MRFW : OCR disabled while fw downgrade from 6.12 to 6.4	( SCGCQ01198953 port of SCGCQ01117827) 
 - IOP: MCTP: In I2C slave response mode low level errors can have two responses	( SCGCQ01203063 port of SCGCQ01189751) 
 - IOP: MPI FW Upload processing time enhancement	( SCGCQ01249413 port of SCGCQ01244472) 
 - 9400-8i and 9400-16i HBAs blinks incorrect slot LED when Locating drive slot	( SCGCQ01256692 port of SCGCQ01256391) 
 - IOP: MCTP: Controller aborted and failed MCTP discovery after several server DC power cycles	( SCGCQ01262784 port of SCGCQ01252343) 
 - IOP: MCTP: Miscellaneous defects exposed by MPI FW Download over MCTP PCIe VDM	( SCGCQ01262885 port of SCGCQ01237010) 
 - IOP WA:PCIe Config trap on Adv Error Capability and Control Register(Offset 0x118	( SCGCQ01278490 port of SCGCQ01271703) 
 - Disable PUIS(Power up in standby	( SCGCQ01305332 port of SCGCQ01304887) 
 - Chassis slot valid bit is not set into Enclosure Page 0.	( SCGCQ01326055 port of SCGCQ01323680) 
 - CSET: Update 9400 series Channel HBAs Drv Strength - (SCGCQ01321017	( SCGCQ01326640 ) 
 - PD Lost observed, after system graceful reboot or Controller OCR	( SCGCQ01327295 port of SCGCQ01314168) 
 - Marlin B0: backend PCIe: EC6D fault on link glitch	( SCGCQ01337660 port of SCGCQ01336021) 
 - Ventura: PL FW may Fault x61A5 during cable pull to an external enclosures with IOs outstanding	( SCGCQ01342226 port of SCGCQ01334254) 
 - Fixed SAS cleanup code to skip the PCI device instances.	( SCGCQ01342335 port of SCGCQ01332893) 
 - SATA Only : 48bit ATA pass through command with lower nibble of LBA(47:40	( SCGCQ01346820 port of SCGCQ01339000) 
 - ISA: Adding FW support for EPD creation through CfgDcmdAdd	( SCGCQ01368242 port of SCGCQ00831836) 
 - USA: Add a debug functionality to log all non-IO commands for a single EPD or multiple EPDs through debug( SCGCQ01368261 port of SCGCQ00856330) 
 - ExpressSDS: Populate the isEPD flag in MR_PD_INFO	( SCGCQ01368288 port of SCGCQ00879185) 
 - SDS:MonTask: line 2285 in file ../../dm/mpt2/mptrec.c	( SCGCQ01368310 port of SCGCQ00889634) 
 - FW not initiating copy back/rebuild after 24 Hour IO while monitoring the drive performance of the configured drives.	( SCGCQ01368320 port of SCGCQ00899866) 
 - Need to post the SystemResetRequired event when OCR happens and there is a personality switch is pending	( SCGCQ01368324 port of SCGCQ00902742) 
 - SDS:Ctrl _R allows to start copyback and it leads to loss EPDs	( SCGCQ01368351 port of SCGCQ00915715) 
 - ExpressSDS: Track the devices through "doNotAutoConfigureAsEPD" when the EPD or VD is deleted	( SCGCQ01368362 port of SCGCQ00925510) 
 - ExpressSDS: Physical drive pass-through SCSI commands are incorrectly tagged during task management	( SCGCQ01368383 port of SCGCQ00938273) 
 - Printing of serial number during the degraded media event	( SCGCQ01368384 port of SCGCQ00938286) 
 - SDS: Kill adapter observed while changing drive state from BAD to GOOD	( SCGCQ01368404 port of SCGCQ00945322) 
 - eSDS1.1:wrong message is displayed while in EPD mode when there no VD's present	( SCGCQ01370529 port of SCGCQ01064584) 
 - CSET: ISA: Disable SBBM for EPDs - (SCGCQ00837450	( SCGCQ01372358 ) 
 - Ventura: Slot LED status update operation may fail on 8i based HBAs	( SCGCQ01373072port of SCGCQ01372983) 
 - Ventura IOP: Firmware becomes unresponsive if host performs I2C transactions	( SCGCQ01388680 port of SCGCQ01379847) 
 - pl: backend PCIe: EC79 fault	( SCGCQ01389704 ) 
 - PL: Sending nonstop ATA Passthrough followed by unsupported SCSI commands rapidly to SATA device can cause a Call Stack Overflow	( SCGCQ01390853 port of SCGCQ01314465) 
 - Making MCTP interrupt context code FIQ safe.	( SCGCQ01391426 ) 
 - Virtual SES is not seen in Windows systems.	( SCGCQ01397678 ) 
 - Defect fix - Hang issue due to - mprintf in ISR and disable TtyLogToFlash, ses Bad phy rery count set to 5	( SCGCQ01399103 port of SCGCQ01377935) 
 - If an INVALID applicationMsgTag id received, then failed the command with MFI_OOB_STATUS_INVALID_CMD using command id MAX_OOB_COMMANDS.	( SCGCQ01399818 port of SCGCQ01337332) 
 - Ventura IOP: Implement workaround for device attached to PCIe front end	( SCGCQ01403449 port of SCGCQ01397501) 
 - Interrupting Offload will Lead to Next offload cycle to fail	( SCGCQ01404399 port of SCGCQ01399701) 
 - Exception Handler Return address 0x01362c7d when boot up	( SCGCQ01405520 port of SCGCQ01404373) 
 - PL Discovery: After Port Down, Expander Is Not Removed and Firmware Retries SMP Indefinitely	( SCGCQ01411982 port of SCGCQ01295414 ) 
 - MCTP I2C: I2C traces shows partial response/zero’ed out packet response from the HBA	( SCGCQ01421231 port of SCGCQ01394463) 
 - Added NVME passthrough support for MR stack	( SCGCQ01422211 port of SCGCQ01391416 ) 
 - Event shown incorrectly if supercap missing	( SCGCQ01431068 port of SCGCQ01425227) 
 - MR 7.4 - Hitting DC after OCR on 240 EPDs	( SCGCQ01439279 port of SCGCQ01412665) 
 - 9460-16i disappears from F1 setup after encrypting SED	( SCGCQ01450194 port of SCGCQ01326871) 
 - MR 7.4 - Hitting DC after OCR on 240 EPDs	( SCGCQ01454603 port of SCGCQ01412665) 
 - Disable user option to modify Multi Init/ SES Management/multiPath feature.	( SCGCQ01455679 port of SCGCQ01441181) 
 - Uncorrectable Medium / DIF Errors are not being handled correctly with pi enabled VDs.	( SCGCQ01459785 port of SCGCQ01447250) 
 - "phy 8 disabled" in tty log - After time sync and after VD creation	( SCGCQ01459789 port of SCGCQ01452263) 
 - Fatal FW Error during CopyBack and partial VD creations on a spanned VD.	( SCGCQ01459793 port of SCGCQ01453168) 
 - Ventura: FW may fault with 265D when attached to OEM NVMe backplane	( SCGCQ01461873 port of SCGCQ01385700) 
 - (VSES	( SCGCQ01463865 port of SCGCQ01458388) 
 - IO Stress Automation test failed while trying to delete VDs; OCR seen in TTY	( SCGCQ01466377 port of SCGCQ01454667) 
 - Flashed based 256 byte VPD programming support	( SCGCQ01466941 port of SCGCQ01330751) 
 - 9460-16i disappears from F1 setup after encrypting SED	( SCGCQ01466955 port of SCGCQ01326871) 
 - Flashed based 256 byte VPD programming support	( SCGCQ01474040 port of SCGCQ01330751) 
 - Inserting enclosures results in unconfigured good PDs changing to R0 automatically and should not	( SCGCQ01474091 port of SCGCQ01462655) 
 - Assertion failure in ../../raid/cache.c found while running multipath push/pull with IO'	( SCGCQ01474449 port of SCGCQ01466815) 
 - 930-16i Cannot Spinup HDD During System Power On	( SCGCQ01478865 port of SCGCQ01470741) 
 - Bugzila 112779 - [PM863A SSD can not show the "Part Number"/ "FRU Number" information under Host tool web w	( SCGCQ01481032 port of SCGCQ01435624) 
 - Server (Purley	( SCGCQ01481100 port of SCGCQ01250426) 
 - Fixed the issue with older ibutton	( SCGCQ01482228 port of SCGCQ01455738) 
 - Additional changes needed for SCGCQ01470741: 930-16i Cannot Spinup HDD During System Power On.	( SCGCQ01482898 port of SCGCQ01482688) 
 - Make NVRAM changes to support Transport Ready	( SCGCQ01484501 port of SCGCQ01464212) 
 - Ventura B0: Fault 0x510B while doing reboot test along with IOs & TMs	( SCGCQ01487266 port of SCGCQ01440764) 
 - [17B] Bugzila 120384 - [MFG] Purley Cosmo Raid card 530-8i loss during MQT1&2 Test	( SCGCQ01511223 port of SCGCQ01504243) 
 - [17B] Bugzila 120384 - [MFG] Purley Cosmo Raid card 530-8i loss during MQT1&2 Test	( SCGCQ01511224 port of SCGCQ01504243) 
 - PL owned mids are not getting released even after removing drives (SATA	( SCGCQ01512617 port of SCGCQ00846818) 
 - Ventura hardware does not like the IOP enable method used here.	( SCGCQ01519729 port of SCGCQ01514880) 
 - storcli show phyerror will return error in some test in some scenario	( SCGCQ01520063 port of SCGCQ01507899) 
 - MR FW is setting GPIO_SET_BBU_ENABLE(GPIOA8	( SCGCQ01521377 port of SCGCQ01519558) 
 - (SATA Only	( SCGCQ01524353 port of SCGCQ01516277) 
 - MegaRAID BIOS didnot timeout and cause Server boot hung when Controller Boot Fail because of bad SPD	( SCGCQ01524448 port of SCGCQ01447768) 
 - MR7.3.1 : iMR FW locks up and PSOD seen while trying to flash MR7.2.1 FW ROP	( SCGCQ01526202 port of SCGCQ01516986) 
 - Controller is not detecting in the storelib, after changing the mode from "set mode oob" command	( SCGCQ01530310 port of SCGCQ01494018) 
 - OEM Tool failure on OEM controller while I/O is running in background	( SCGCQ01530478 port of SCGCQ01525935) 
 - pl: NVMe: EC0D fault	( SCGCQ01533267 port of SCGCQ01530402) 
 - Systerm hang up with 0x73 code when entering S4 with 9440-8i+SAS RAID1 under RHEL7.3 GA	( SCGCQ01538776 port of SCGCQ01396610) 
 - pl: backend PCIe: link workaround not sufficiently coordinated with SAS link establishment	( SCGCQ01556893 port of SCGCQ01540226) 
 - storcli shows 8ports controller as 9 ports	( SCGCQ01561912 port of SCGCQ01478353) 
 - Fault LED behavior is not consistent between PD direct attached vs connected via expander	( SCGCQ01577461 port of SCGCQ01508065) 
 - To fix the phy to slot mapping issue for the UBM backplane	( SCGCQ01582244 port of SCGCQ01542497) 
 - CC doesn't start on special built OEM firmware	( SCGCQ01582532 port of SCGCQ01559661) 
 - (SATA Only	( SCGCQ01593192 port of SCGCQ01539572) 
 - Add logging messages in addition to previous fixes of a related issue, as requested by the Customer.	( SCGCQ01602617 port of SCGCQ01584278) 
 - Device block and unblock messages observed for the existing connected NVMe drives when new NVMe drive is inserted	( SCGCQ01628423 port of SCGCQ01615532) 
 - The change detect feature macro missing, leading to compilation issue	( SCGCQ01628445 port of SCGCQ01616460) 
 - Not all NVMe drives discovered as part of hot plug operation	( SCGCQ01713380 port of SCGCQ01697329) 
 - Relaxed ordering Enhancement	( SCGCQ00136149 port of SCGCQ00131448) 
 - IR: Write cache not set correctly when fast resync is turned off due to a path pull on a multipath volume	( SCGCQ00136968 port of SCGCQ00127534) 
 - Fast resync is not turned back on a new resync once it has been turned off.	( SCGCQ00138308 port of SCGCQ00135763) 
 - IR: Physical disk used as a replacement device is uncorrectly unhidden to the host	( SCGCQ00138309 port of SCGCQ00126563) 
 - Data corruption seen while inserting the drive on a degraded volume during port reset.	( SCGCQ00138312 port of SCGCQ00135108) 
 - "Pause When Boot Alert Displayed" Intermittently Switching State	( SCGCQ00141733 port of SCGCQ00141052) 
 - IOP: Fixed Ethernet Bios Download	( SCGCQ00154513 port of SCGCQ00141825) 
 - Ethernet FWDL Code Review Modifications	( SCGCQ00154726 port of SCGCQ00150083) 
 - Allocate ISTWI device types and GPIO function codes for vendor specific use	( SCGCQ00155105 port of SCGCQ00151361) 
 - Thunderbolt B0 SBR not working.	( SCGCQ00156211 ) 
 - 9200-16e Target Port stops accepting I/Os after a certain number of I/Os on Phase 6 firmware	( SCGCQ00156441 port of SCGCQ00148044) 
 - Running MSC commands prior to running MSC init causes 265D fault	( SCGCQ00157578 port of SCGCQ00149262) 
 - During USB enumeration process the controller faults with Fault 0D04	( SCGCQ00157679 port of SCGCQ00147899) 
 - Ethernet FWDL: Firmware download from a TFTP Server occasionally fails.	( SCGCQ00160484 port of SCGCQ00151758) 
 - PCIe link width change returns 300a0007 loginfo even when request is honored exactly	( SCGCQ00160508 port of SCGCQ00153294) 
 - CLI Command Processing when firmware is hung in infinite loop	( SCGCQ00169003 port of SCGCQ00135538) 
 - (Thunderbolt	( SCGCQ00169006 ) 
 - (IOP-Only	( SCGCQ00169149 ) 
 - Virtualization: Fault 7D70 with port virtualization enabled firmware.	( SCGCQ00172536 port of SCGCQ00149660) 
 - IR: Hot plug/pull of large capacity configured drives fails	( SCGCQ00172675 port of SCGCQ00168900) 
 - use MPI2_RAIDVOL0_STATUS_FLAG_VOL_NOT_CONSISTENT, remove MPI2_RAIDVOL0_STATUS_FLAG from mpi_temp.h	( SCGCQ00172678 port of SCGCQ00168536) 
 - (IOP-Only	( SCGCQ00178838 ) 
 - _delay member is too small to hold all reasonable delay lengths for data scrub duration.	( SCGCQ00184817 port of SCGCQ00181619) 
 - Similar to SCGCQ00162017, enhance Gen2 IR firmware to keep tabs on which IR RAID volumes contain SSD physical disks	( SCGCQ00188490 port of SCGCQ00162018) 
 - 8111h fault occurs while activating a foreign volume on an adapter which already has failed volume with all the physical disks missing	( SCGCQ00188497 ) 
 - Thunderbolt: Update several I2C register fieldwidths for Thunderbolt I2C 80 byte FIFO per new I2C spec	( SCGCQ00188776 port of SCGCQ00172272) 
 - MPI2_IOCFACTS_PROTOCOL_SCSI_TARGET is set in Protocol Flags of IOC Facts Reply	( SCGCQ00192702 port of SCGCQ00184400) 
 - (SRIOV-Only	( SCGCQ00201909 port of SCGCQ00182572) 
 - (SRIOV	( SCGCQ00202280 port of SCGCQ00152255) 
 - (SRIOV IOC	( SCGCQ00202338 port of SCGCQ00176722) 
 - Fix Global Variables in iButton code to match coding standard( SCGCQ00204066 port of SCGCQ00183854) 
 - (IOP-Only	( SCGCQ00204072 port of SCGCQ00152253) 
 - (BUILD	( SCGCQ00204225 port of SCGCQ00179033) 
 - When HDDs are removed from RAID10, the other drives go down and come back up.	( SCGCQ00222300 port of SCGCQ00202499) 
 - Non-PI volume becomes PI at activation time	( SCGCQ00235660 port of SCGCQ00220596) 
 - Creating mixed PI/non-PI volume fails	( SCGCQ00235663 port of SCGCQ00220046) 
 - USB: The usb device is not always discovered after a cold start	( SCGCQ00237773 port of SCGCQ00217192) 
 - Add PI to IR: BGI Changes - Add Fast Initialize	( SCGCQ00237872 port of SCGCQ00194018) 
 - IR 4K: IR Base 4K Support	( SCGCQ00243092 port of SCGCQ00222449) 
 - IR 4K: Metadata Changes	( SCGCQ00243103 port of SCGCQ00222424) 
 - A PI Hot Spare is allowed to failover to a non-PI volume with PI Mixing Disabled	( SCGCQ00243485 port of SCGCQ00243257) 
 - IR 4K: Internal IO 4K support	( SCGCQ00243509 port of SCGCQ00222497) 
 - (Hydra	( SCGCQ00260080 port of SCGCQ00260079) 
 - Ph13 IR: 0x8109:IFAULT_IR_NON_ZERO_IO_COUNT – seen while removing R0 member drive during Host IO’s	( SCGCQ00277814 port of SCGCQ00246057) 
 - Saving a host diagnostic trace buffer from the console does not work	( SCGCQ00279501 port of SCGCQ00245530) 
 - Remove hardcoded shift value in Raid Accelerator code path	( SCGCQ00280174 port of SCGCQ00242024) 
 - IR: PI: MDC runs on a SSD Volume created on a PI-enabled controller when roamed/activated after clean shutdown	( SCGCQ00294989 port of SCGCQ00220978) 
 - Update Toolbox CLI debug on firmware fault	( SCGCQ00307292 port of SCGCQ00268561) 
 - Inactive foreign volume information cannot be seen in SASBIOS when a native volume is deleted.	( SCGCQ00316588 port of SCGCQ00239295) 
 - Microcode Update Events for SAS2 Integrated RAID	( SCGCQ00317002 port of SCGCQ00268946) 
 - (IOP	( SCGCQ00326692 port of SCGCQ00260083) 
 - BST : Overnight build copy has to be modified to run from a new location.	( SCGCQ00471482 port of SCGCQ00359691) 
 - Added Gen 3 Support for Decoding Snapshot Buffers - Enhanced Debug Capabilities	( SCGCQ00472604 port of SCGCQ00353036) 
 - Enable parity checking in certain portions of the XMem and PCIe blocks	( SCGCQ00473403 port of SCGCQ00361701) 
 - (PL	( SCGCQ00473994 port of SCGCQ00382525) 
 - Golden Utility to create 8MB, 16MB, 32MB, and 64MB Flash Images	( SCGCQ00477175 port of SCGCQ00381826) 
 - IOP: Improve PCI-Express core register dump to assist debug	( SCGCQ00552439 port of SCGCQ00376555) 
 - IOP VPD compile option cleanup	( SCGCQ00552445 port of SCGCQ00382511) 
 - PL: SAT3 compliance - Implement translation of SCSI Sanitize command.	( SCGCQ00553450 port of SCGCQ00357129) 
 - Invader B0: IO Unit Page 7 Current Power Mode does not match the IOCSpeed after a reset.	( SCGCQ00554337 port of SCGCQ00369197) 
 - IOP: Fault 0x2628 at start of day	( SCGCQ00559718 port of SCGCQ00414504) 
 - (IOP	( SCGCQ00559721 port of SCGCQ00417993) 
 - IOP: SR-IOV firmware fails to respond correctly to VM initialization	( SCGCQ00564388 port of SCGCQ00422771) 
 - GenCRC utility incorrectly calculates the image size internally	( SCGCQ00564832 port of SCGCQ00564201) 
 - (IOP	( SCGCQ00565118 port of SCGCQ00446539) 
 - IOP: MCTP incorrectly obtains I2C Speed config using Mfg Page 8	( SCGCQ00565493 port of SCGCQ00422103) 
 - Check in target error injection code	( SCGCQ00565506 port of SCGCQ00393701) 
 - IOP: Enable MCTP support in IT/IR firmware.	( SCGCQ00565508 port of SCGCQ00396012) 
 - Messages can be check for corruption or corruption of the Packet Error Code (PEC	( SCGCQ00565509 port of SCGCQ00396020) 
 - SR-IOV: VFs performing firmware uploads unexpectedly are blocked	( SCGCQ00566113 port of SCGCQ00448263) 
 - cli commands iop fpe maxex & maxev value do not allow reseting to the max SOD setting	( SCGCQ00566121 port of SCGCQ00457383) 
 - (PL	( SCGCQ00566165 ) 
 - IOP: MCTP: I2C Address Byte ACKing by HW reduces time to transmit FW IN WRONG STATE Packet Exception	( SCGCQ00566194 port of SCGCQ00527722) 
 - IOC Init Multiple reply descriptor post queue host addresses	( SCGCQ00566241 port of SCGCQ00475659) 
 - ONFI library should not be built for default IT build	( SCGCQ00568399 port of SCGCQ00390519) 
 - Invalid debug print string for IOP_DBG_STR_MSG_HANDLER_PORT_ENABLE	( SCGCQ00665138 port of SCGCQ00661502) 
 - Add power condition ASC/ASCQ definition	( SCGCQ00725198 port of SCGCQ00606283) 
 - Firmware downgrade fails and firmware faults with code 0x070A	( SCGCQ00725243 port of SCGCQ00592281 ) 
 - IOP: MCTP: Packets with valid MCTP SeqCount values are dropped	( SCGCQ00725344 port of SCGCQ00673173) 
 - IOP: MCTP: Fault 0x2667 when set PCIe BusMaster, then clear, and send MCTP Request with PCIe VDM	( SCGCQ00725345 port of SCGCQ00675583) 
 - IOP: MCTP messages: Test size of MPI Event Notification Request in MCTP	( SCGCQ00725348 port of SCGCQ00645292) 
 - IOP: SR-IOV Virtual Functions are able to access BIOS configuration pages	( SCGCQ00725369 port of SCGCQ00664321) 
 - PL: Implement customer specific SAS topology restrictions	( SCGCQ00741763 port of SCGCQ00697961) 
 - Implement means of saving critical OEM config data so that it can easily be persisted through a firmware down-rev.	( SCGCQ00757684 SCGCQ00566512) 
 - Update Attribution Language - Copyright, Trademark, Confidentiality to Avago	( SCGCQ00758949 port of SCGCQ00729467) 
 - IOP: MCTP: Log Entry Added event triggered from wrong event	( SCGCQ00781343 port of SCGCQ00713624) 
 - IOP: CLI command to dump L1 data cache causes 0x265D fault	( SCGCQ00781347 port of SCGCQ00715317) 
 - IOP: Config page code null references and uninitialized variable fixes	( SCGCQ00781368 port of SCGCQ00730692) 
 - IOP: Config space read during startup can cause firmware lockup	( SCGCQ00781377 port of SCGCQ00735541) 
 - IOP: MCTP: PageType with non-zero Attributes for Config Page Request fails	( SCGCQ00793932 port of SCGCQ00755365) 
 - IOP: MCTP: Send Get VDM Support MCTP Control request and obtain incorrect padding size	( SCGCQ00793940 port of SCGCQ00767204) 
 - IOP: MCTP: Fail to find first entry when number of Log Page 0 Entries are less than 128	( SCGCQ00793941 port of SCGCQ00768566) 
 - IOP: Add GPIO Write protect pin feature for SBR EEPROM	( SCGCQ00816411 port of SCGCQ00790308) 
 - Ventura: MSS - FPGA fixes and other misc	( SCGCQ00821603 port of SCGCQ00810018) 
 - Tiger WW: Use controller LMids as SED SMids	( SCGCQ00839590 port of SCGCQ00804417) 
 - Tiger WW: Update to official MPI SED initialization messages	( SCGCQ00841599 port of SCGCQ00830343) 
 - Invader C0: Performance drops with PL version 0.250.113.0 on 2 R0 volumes behind Cobra	( SCGCQ00855687 port of SCGCQ00400569) 
 - non-SafeStor based SED support for EPD in SDS personality	( SCGCQ01294806 port of SCGCQ00882667) 
 - pl: NVMe: unexpected IO failures with firmware path read/write IOs to an NVMe SGL device	( SCGCQ01326943 port of SCGCQ01321013) 
 - Ventura: AltData select, RefClk Mux not setup for SGPIO initiator prior to init	( SCGCQ01328967 port of SCGCQ01321764) 
 - Ventura/Marlin: backend PCIe: IO halt after a link glitch	( SCGCQ01337661 port of SCGCQ01336859) 
 - PL : performance drop of nearly 40% in sequential write and seqential Reads	( SCGCQ01341898 port of SCGCQ01333993) 
 - PL Fault 0000d074 when run IOMeter overnight R0 fastpath	( SCGCQ01346368 port of SCGCQ01331410) 
 - Ventura: SPI FLASH fails to write data (fails on read-back	( SCGCQ01355010 port of SCGCQ01349880) 
 - NVMe-enabled firmware fails to host boot on a blank board	( SCGCQ01358762 port of SCGCQ01358750) 
 - ExpressSDS: Disable Recon on EPD volumes	( SCGCQ01368293 port of SCGCQ00881409) 
 - ESDS: in smartPoll thread Fail EPD if dontFailPdOnError in autoConfigParam is not set	( SCGCQ01368322 port of SCGCQ00901373 ) 
 - ExpressSDS: Avoid shield disk start for EPD drives	( SCGCQ01368377 port of SCGCQ00934598) 
 - eSDS:FW crash observed at line 245 in file ../../raid/1078int.c while doing target reset through storcli on EPD's	( SCGCQ01368399 port of SCGCQ00944248) 
 - eSDS: Avoid Write Cache Sync for EPDs	( SCGCQ01368410 port of SCGCQ0095146) 
 - eSDS_1.1: After flashing the merged binary firmware the previous configuration is moving into the foreign	( SCGCQ01370441 port of SCGCQ01023963) 
 - MR6.12_Code MergeIssue after Baseline	( SCGCQ01370447 ) 
 - Non SafeStor - FW reports failure when initiate "Instant Secure Erase" against Foreign Locked PDs	( SCGCQ01370531 port of SCGCQ01064725) 
 - Issue - During OCR when recon is in progress, fw breaks due to exception.	( SCGCQ01399526 port of SCGCQ01385063) 
 - Occasionally StorLib OOB commands fails due to I2C timeout	( SCGCQ01399822 port of SCGCQ01380640) 
 - 3408IMR set jbod on a specified disk will cause enter FW break into megamon	( SCGCQ01399885 port of SCGCQ01389506) 
 - PL: LUN Reset Option for Avoid Duplicate Mid Feature	( SCGCQ01401595 port of SCGCQ01399068) 
 - Ventura: Implement workaround for device attached to PCIe front end with IDT timer	( SCGCQ01430621 port of SCGCQ01401585) 
 - Replacing RAID Controller with Degraded VD Hangs System	( SCGCQ01430637 port of SCGCQ01393703) 
 - Customer experiences 5-7 % performance drop on 24 direct connected SAS SSD R10/R6 setup.	( SCGCQ01442976 port of SCGCQ01417361) 
 - CISCO LB PVT issue - Foreign import failure	( SCGCQ01445274 port of SCGCQ01391311) 
 - Ventura/Marlin: NMI due to Host-side PCE credit starvation when there are simultaneous accesses to MSIX table and Generic Messaging Queue	( SCGCQ01445831 ) 
 - Make TTY buffer Lossy	( SCGCQ01449236 ) 
 - Direct attached VSES Enclosure validation may fail with certain OS tools	( SCGCQ01451191 port of SCGCQ01445053) 
 - PL: EnclMgmt: Move ownership of SES Page 0x0A slot mapping from devices to PHYs	( SCGCQ01458359 port of SCGCQ00870423) 
 - Ventura: Add support for OEM specific NVMe backplane detection and slot LED control	( SCGCQ01460731 port of SCGCQ01346574) 
 - Ventura MR - MR 7.4 not discovering NVMe devices	( SCGCQ01462088 port of SCGCQ01453903) 
 - When PFA drive is attached, it does not show predictive failure is detected.	( SCGCQ01466076 port of SCGCQ01420232) 
 - Drives in Enclosure spin up values for OEM board is not initialized correctly	( SCGCQ01466079 port of SCGCQ01450221) 
 - Bad Drives in system causing Assert id!=MPT_FRAME_ALLOC_ID_ILLEGAL	( SCGCQ01466370 port of SCGCQ01446154) 
 - Disabling large IO support leads to invalid argument .	( SCGCQ01466389 port of SCGCQ01460440) 
 - Controller hangs after updating to latest ROP 676	( SCGCQ01470577 port of SCGCQ01422235) 
 - Block Downgrade of Firmware	( SCGCQ01472912 ) 
 - VSES Target not added in host if event replay slot ordering is enabled.	( SCGCQ01474945 port of SCGCQ01471601) 
 - Adding PnPId check for break/join mirror	( SCGCQ01486444 port of SCGCQ01288928) 
 - MPI SEP request to Slots with invalid SES Page 0A element index may not complete	( SCGCQ01487259 port of SCGCQ01482937) 
 - BMC emulator on Ventura failed with Storlib discovery	( SCGCQ01488146 port of SCGCQ01410607) 
 - Enhance SAS3 FW to pass PCIeCV PCIe Configuration Validation TD_1_28 Vital Product Data Capability Test	( SCGCQ01499168 port of SCGCQ00878239) 
 - Create compile option to disable SPL 2 power control	( SCGCQ01499175 port of SCGCQ01468141) 
 - PKG 886 10.1/When upgrading from 678 10.0 to 10.1 886 and switching to 240VD, I am unable to create 240VD	( SCGCQ01505145 port of SCGCQ01503263) 
 - pl: backend PCIe: 4311 fault with NVMe enabled	( SCGCQ01520574 port of SCGCQ01514521) 
 - Controller can not correctly detected smart error SATAA HDD.	( SCGCQ01521373 port of SCGCQ01506289) 
 - (SATA Only	( SCGCQ01524638 ) 
 - pl: NVMe: PCIe reconfiguration may occur during NVMe controller reset	( SCGCQ01527219 port of SCGCQ01526236) 
 - Linux driver incorrect issuing MR_DCMD_DEV_GET_TARGET_PROP to enclosure devices	( SCGCQ01540362 port of SCGCQ01403758) 
 - Aero : Continous error( MptHostCmdDone cmdId=fe lmid=8a2:1851b400 tid 04 devH ..	( SCGCQ01558211 port of SCGCQ01540433) 
 - PL: Revised "Avoid Duplicate Mid" Feature Code Could Incorrectly Allow IO to Start Through PL Firmware Path	( SCGCQ01559005 port of SCGCQ01520524) 
 - Assertion failure in ../../mros/mem.c : mb->tag==tag	( SCGCQ01561911 ) 
 - pl: NVMe: Write Long (10	( SCGCQ01601702 ) 
 - (SATA Only	( SCGCQ01621654 ) 
 - AULBA divert bitmap not enabled on R5/R6 WT Vds	( SCGCQ01627798 port of SCGCQ01619858) 
 - USB - Enhance UART command line error reporting	( SCGCQ00155169 port of SCGCQ00149359) 
 - (IOP-Only	( SCGCQ00156183 port of SCGCQ00149388) 
 - (IOP-Only	( SCGCQ00160240 port of SCGCQ00160020) 
 - IOP: Uart console command "iop show sbr" only shows 1st copy of SBR correctly	( SCGCQ00160406 port of SCGCQ00152263) 
 - Manufacturing Page Block create routine should not be part of cfgi library build.	( SCGCQ00160460 port of SCGCQ00153144) 
 - (CFGI	( SCGCQ00163435 ) 
 - Unplugging USB end device during IOP USB TEST hangs firmware	( SCGCQ00164454 port of SCGCQ00150267) 
 - USB - Remove debug memory allocation from USB init	( SCGCQ00164456 port of SCGCQ00156250) 
 - Thunderbolt : USB Cache Offload Support	( SCGCQ00168679 port of SCGCQ00138336) 
 - MPB parser output skips 2 bytes of each MPB entry data	( SCGCQ00177564 port of SCGCQ00163581) 
 - IR: Support for >2TB drives	( SCGCQ00188493 port of SCGCQ00172837) 
 - IOP: memory leak in uart diag command	( SCGCQ00192204 port of SCGCQ00180224) 
 - USB: Diagnostic command does not write as much data as expected	( SCGCQ00193408 port of SCGCQ00182843) 
 - (IOP-Only	( SCGCQ00194475 port of SCGCQ00172979) 
 - (SRIOV-Only	( SCGCQ00201918 port of SCGCQ00179265) 
 - (IOP-Only	( SCGCQ00209165 port of SCGCQ00192918) 
 - 265D fault during hostboot on Mustang	( SCGCQ00225381 port of SCGCQ00152378) 
 - The fill pattern for the BBM section between 2048 and 4095 is incorrect.	( SCGCQ00243957 port of SCGCQ00231203) 
 - PL: SAS Gen-2 Open Reject (No Dest	( SCGCQ00258361 port of SCGCQ00247227) 
 - Add snapshot tool	( SCGCQ00269259 port of SCGCQ00231954) 
 - PL: Do not send up additional SAS Topology Change List Events for phys with a Function Result of Phy Vacant	( SCGCQ00437102 ) 
 - Enable UART during Critical Interrupt while in fault state by default	( SCGCQ00470297 port of SCGCQ00362615) 
 - In fault state, Ioc2Sys Doorbell IRQ is cleared before host polls the register to see the fault	( SCGCQ00471502 port of SCGCQ00367931) 
 - Invader C0: Power Management code is not checking the Substate Control Enable bit prior to changing to the power state.	( SCGCQ00559715 port of SCGCQ00384416) 
 - Fixed 6001 Fault Caused by Defects in Task Management	( SCGCQ00562743 port of SCGCQ00421304) 
 - Update product ID in the firmware header to Invader family.	( SCGCQ00563396 port of SCGCQ00415058) 
 - IOP: Sideband management message handling (Init, Inventory, ID, Version	( SCGCQ00565502 port of SCGCQ00391851) 
 - (NVDATA	( SCGCQ00566088 port of SCGCQ00406234) 
 - IOP: PCIe Compliance test failing config space read at start of day	( SCGCQ00566139 port of SCGCQ00460949) 
 - Changing PCI Link Width is not supported so we need to remove pci lnkwdw	( SCGCQ00566149 port of SCGCQ00464903) 
 - Added additional checks to MCTP Msg layer (iopMCTPMsgCmdStart(	( SCGCQ00566185 port of SCGCQ00504029) 
 - Update SAS9311-8i IR NVDATA for Channel configuration requirements	( SCGCQ00566223 port of SCGCQ00438969) 
 -	( SCGCQ00572868 port of SCGCQ00421660) 
 - ManPage14 XSD setting incorrect for RebuildAbort state	( SCGCQ00725234 port of SCGCQ00575789) 
 - PL: Update EDFBMaxGroupUnload default value to 4 and add debug features	( SCGCQ00725281 port of SCGCQ00551447) 
 - IOP: SR-IOV: Some SAS IO Unit Control messages from VFs are incorrectly rejected	( SCGCQ00781315 port of SCGCQ00694683) 
 - IOP: MCTP: Handle allocation failure for received packet and additional post-processing cleanup	( SCGCQ00781337 port of SCGCQ00710478) 
 - IOP: TLB initialization may fail to identify the running memory model	( SCGCQ00781359 port of SCGCQ00728893) 
 - IOP: MCTP packet exception could cause null pointer dereference	( SCGCQ00793920 port of SCGCQ00730742) 
 - IOP: MCTP: SenseData handling with MPI SCSI IOs causes firmware to lose those responses	( SCGCQ00793939 port of SCGCQ00767189) 
 - IOP: Correct change topology list event print	( SCGCQ00803153 port of SCGCQ00802751) 
 - ExpressSDS 1.1: True Multipath Host Task Management	( SCGCQ01294902 port of SCGCQ01024444) 
 - More latency observed during device discovery	( SCGCQ01327290 port of SCGCQ01311662) 
 - CSET: Disable PCIe support for 8e PHYs on 9400-8i8e NVMe - (SCGCQ01334509	( SCGCQ01335058 ) 
 - Ventura: Add TM IOCStatus to TM Logger	( SCGCQ01338919 port of SCGCQ01336984) 
 - 4k Read of EPMR12 is low comparing to OEM specific stream	( SCGCQ01350594 port of SCGCQ01283594) 
 - ISA: Blocking the creation of JBOD in EPD behaviour even when the enableJBOD is set	( SCGCQ01368239 port of SCGCQ00827012) 
 - Support auto-configuration option and parameter related events, show information for EPDs	( SCGCQ01378994 port of SCGCQ01024552) 
 - Making MCTP interrupt context code FIQ safe.	( SCGCQ01391425 port of SCGCQ01387060) 
 - Disks report incorrect rotational speeds	( SCGCQ01402214 port of SCGCQ01391462) 
 - Ventura: Implement workaround for device attached to PCIe front end with IDT timer	( SCGCQ01448014 port of SCGCQ01401585) 
 - OS hung and iMR FW reset when do delete and create VD from previous powersave PD (Spindowned	( SCGCQ01458055 port of SCGCQ01287286) 
	Page 26 / 391
 - Replace Member PD failed to copy back on a 4KN data protected VD	( SCGCQ01459797 port of SCGCQ01455224) 
 - pl: port enable may fail to complete if an OEM backplane is attached	( SCGCQ01464752 port of SCGCQ01455680) 
 - PD FW update fails on iMR controller using MCTP over PCIe in from IMM debug console.	( SCGCQ01466972 port of SCGCQ01235906) 
 - MR7.0.1 iMR shows exception after flashing	( SCGCQ01467853 port of SCGCQ01325384) 
 - To check if NVRAM changes related to upgrade/downgrade issue is present	( SCGCQ01473201 port of SCGCQ01473186) 
 - set jbod on a Faulty disk will take several minutes to go to bad state	( SCGCQ01473796 port of SCGCQ01424679) 
 - Performance comparison-Reconstruction R1-R5, Degradation seen with latest release.	( SCGCQ01483109 port of SCGCQ01462723) 
 - iMR: storcli /c0 show termlog didnot get termlog sometimes	( SCGCQ01516689 port of SCGCQ01480662) 
 - When update Vendor SAS 2.5" 10K 12Gbps 300GB HHD (PN:SH20J34185	( SCGCQ01522339 port of SCGCQ01515259) 
 - Get VDM Support command does not have VendorID and VendorAddInfo fields properly populated	( SCGCQ01530305 port of SCGCQ01450475) 
 - Change detect feature support on UBM supported back plane	( SCGCQ01628416 port of SCGCQ01605371) 
 - IR: Invalid Print statement	( SCGCQ00138310 port of SCGCQ00137490) 
 - Ph7 IR: Do read IO load balancing for RAID10/RAID1E ASM volumes for better performance	( SCGCQ00153682 port of SCGCQ00141686) 
 - (IOP-Only	( SCGCQ00155118 port of SCGCQ00118431) 
 - Thunderbolt: Use additional sensors for temperature reporting	( SCGCQ00168582 port of SCGCQ00162475) 
 - (SRIOV-Only	( SCGCQ00201704 port of SCGCQ00176726) 
 - (SRIOV	( SCGCQ00203084 port of SCGCQ00152254) 
 - IR firmware causes fault 0x501 when SEND DIAGNOSTIC command is issued to a volume.	( SCGCQ00294678 port of SCGCQ00240830) 
 - ASCQ is not set Correctly in Self-Test Results Log Page When SEND DIAGNOSTIC Fails for SATA Drive	( SCGCQ00469664 port of SCGCQ00339568) 
 - Combined reply queue feature	( SCGCQ00472419 port of SCGCQ00374225) 
 - After updating mfg page 2 using config request (write NVRAM	( SCGCQ00472481 port of SCGCQ00395216) 
 - Invader/Fury C0 NVData	( SCGCQ00477181 port of SCGCQ00349992) 
 - Remove unused files from source control	( SCGCQ00552478 port of SCGCQ00391834) 
 - IOP: Script updates to work around GHS probe issue	( SCGCQ00559722 port of SCGCQ00420299) 
 - (IOP	( SCGCQ00566098 port of SCGCQ00432887) 
 - Changing PCI Link Speed is not supported so we need to remove pci lnkspdw	( SCGCQ00566124 port of SCGCQ00457388) 
 - Invader fails PCI-SIG configuration space testing while running the following test on the transmit margin field: Test TD_1_41.	( SCGCQ00566143 port of SCGCQ00461411) 
 - IOP: MCTPMsg: CmdStatus and Event Clean-up not consistent with SCS MCTP Spec	( SCGCQ00566195 port of SCGCQ00527732 ) 
 - Invader: Add Fault Code - Abort Task Missed Its IO with Pend Flag Set	( SCGCQ00566201 port of SCGCQ00559156) 
 - NVDATA Option to Allow Force Dual Context On	( SCGCQ00566265 port of SCGCQ00501686) 
 - MCTP: Add support for PCIe VDM binding	( SCGCQ00725272 port of SCGCQ00481147) 
 - IOP: ISTWI fails to initialize variable and out of bounds array access	( SCGCQ00781351 port of SCGCQ00728104) 
 - In case of Raid 6 and medium error on the drives, if the driver state is manually changed to OFFLINE, FW hits a DMA error	( SCGCQ01198938 port of SCGCQ01162896) 
 - Parallel HDD microcode update support	( SCGCQ01282809port of SCGCQ01023507) 
 -	( SCGCQ01294891 ) 
 - ATA Passthrough MPT frame content has overwritten	( SCGCQ01348118 port of SCGCQ01339127) 
 - Non SafeStor - EPD Push/pull, result into Foreign drive state (ddfType=10 isBroken=0 locked=1 secure=1	( SCGCQ01370528 port of SCGCQ01064307) 
 - ESDS1.1: A kill adapter at line 1280 is observed with IO and cable breaker in multipath with MPIO enabled on RHEL7.2	( SCGCQ01370532 port of SCGCQ01065343) 
 - Replacing RAID Controller with Degraded VD Hangs System	( SCGCQ01403745 port of SCGCQ01393703) 
 - Interrupting Offload will Lead to Next offload cycle to fail	( SCGCQ01404400 port of SCGCQ01399701) 
 -	( SCGCQ01453934 port of SCGCQ01451306) 
 - MR 7.4 : Default VD policy in MR 7.4 is not matching with MR 7.3	( SCGCQ01462731 port of SCGCQ01460649 ) 
 - CISCO - Enable OCR for all release builds.	( SCGCQ01470795 port of SCGCQ01294922 ) 
 - Spare filtering does not prevent NVMe PD from being used as spare for SAS/SATA array.	( SCGCQ01478265 port of SCGCQ01441173) 
 - MR7.3 & 7.4 With iMR Unconfigured NVMe drives become Unconfigured Bad When Converting Them to JBODs	( SCGCQ01483142 port of SCGCQ01479017) 
 - Global HDD LED may not indicate IO activity for NVMe or SAS drives	( SCGCQ01496628 port of SCGCQ01489030) 
 - Disable write cache to default	( SCGCQ01504375 SCGCQ01485047) 
 - OCR is disabled by default is RC build, even NVDATA if it is enabled.	( SCGCQ01520061 port of SCGCQ01503204) 
 - FW automatically delete and create the EPD's with assigning EPD no 3f indefinitely.	( SCGCQ01540335 port of SCGCQ01509726) 
 - Correct minimum voltage calculation of Supercap	( SCGCQ01619844 port of SCGCQ01558901) 
 - FW logging fatal error in case of chip reset, but driver not loaded.	( SCGCQ01623751 port of SCGCQ01594199) 
 - (SATA Only	( SCGCQ01731910 port of SCGCQ01638248) 
 - A config page request to erase log entries in the flash fails.	( SCGCQ00165925 port of SCGCQ00153033) 
 - Fault 0x100 prevents code from running at SOD	( SCGCQ00204223 port of SCGCQ00200602) 
 - rbd: Add changes to strip extra header from text dump	( SCGCQ00365484 port of SCGCQ00365466) 
 - IOP FW : 265D fault after enabling DDR3 2nd rank support	( SCGCQ00471479 port of SCGCQ00300270) 
 - MCTP: Add support for MPI requests	( SCGCQ00565512 port of SCGCQ00396398) 
 - Bootloader: Boot time performance improvements	( SCGCQ00566261 port of SCGCQ00490972) 
 - IOP: MCTP: Debug mode to provide additional information for the Invalid Parameter Packet Exception	( SCGCQ00566267 port of SCGCQ00505168) 
 - Base Address Register at offset 0x1C (BAR3	( SCGCQ00816424 port of SCGCQ00795305) 
 - SafeStor support for EPD in SDS personality in 1.1	( SCGCQ01294894 port of SCGCQ00990749) 
 - Allocate alias targetId for EPDs when true multipath has enabled!	( SCGCQ01294901 port of SCGCQ01024648) 
 -	( SCGCQ01294904 port of SCGCQ01109051) 
 - ESDS: The serial number of the Hitachi drives are truncated when a show pdfailevents options is performed.	( SCGCQ01368373 port of SCGCQ00932844) 
 - Move the ready state after the pin cache is flushed completely	( SCGCQ01368389 port of SCGCQ00941249) 
 - 0x6001 Fault due to a missing IO that went through the IO resubmit path	( SCGCQ01369963 port of SCGCQ01330777) 
 - Handling SEP partner for Expander removal/insertion and path removal insertion	( SCGCQ01370442 port of SCGCQ01024970) 
 - Initiate ocr when FW enters MonTask	( SCGCQ01398246 port of SCGCQ01381615) 
 - USB SCSI commands failing due to I/O timeout.	( SCGCQ00193409 port of SCGCQ00176341) 
 - Command file for PL library distribution did not create a valid ZIP file for the CFGi library.	( SCGCQ00475100 port of SCGCQ00362462) 
 - ISA: Avoid clearing the DDF area for the EPD drive as part of VD delete or clear configurations.	( SCGCQ01368247 port of SCGCQ00837059) 
 - Enable I2C polling for drive presence detection in VPP Type B backplanes with NVMe support.	( SCGCQ01460733 port of SCGCQ01375330) 
 - Spare filtering does not prevent NVMe PD from being used as spare for SAS/SATA array.	( SCGCQ01466124 port of SCGCQ01441173) 
 - Fast Path IO is not failed for LDBBM table entries	( SCGCQ01466133 port of SCGCQ01452385) 
 -	( SCGCQ01466844 port of SCGCQ01420670) 
 - Disable T10 Protection Information support	( SCGCQ01487806 port of SCGCQ01484321) 
 - Add method to determine Ring Buffer Overflow in RMC	( SCGCQ01503207 port of SCGCQ01484941) 
 - Kill Adapter while running IOs on 64 VDs (including slice VDs	( SCGCQ01601265 port of SCGCQ01548019) 
 - LSA version 4.132 shows blank page or extreme sluggish to do anything	( SCGCQ01715426 port of SCGCQ01698418) 
 - SEEPROM Support for 16 byte page/ 1 bit addressing for SBR in Gen2 FW	( SCGCQ00141061 port of SCGCQ00132374) 
 - Replace POM0 usage with SysDma	( SCGCQ01448534 port of SCGCQ01430023) 
 - System will pop up “Cannot communicate with iButton to …” during reboot with customer iMR card (FW:50.2.1-0597	( SCGCQ01450218 port of SCGCQ01447988) 
 - Added NVME passthrough support for MR stack	( SCGCQ01451159 port of SCGCQ01391416) 
 - MR 7.4 - PDs pull/push led to "Assertion failure in ../../cpu/arm/exceptions.c at line 938: 0"	( SCGCQ01484822 port of SCGCQ01460017) 
 - The SUT can’t boot to OS after 159 loops AC cycle and check the Raid 930-16i 8G	( SCGCQ01788547 port of SCGCQ01788479) 
 
 
EnhancementRequests 
 - MPI 2.5: Power Management( SCGCQ00066241 ) 
 - Look into Qfull handling	( SCGCQ00081065 ) 
 - Update firmware to correctly dump all SAS Core registers	( SCGCQ00090999 ) 
 - Gen3: SHELL Performance Monitor	( SCGCQ00095392 ) 
 - Manufacturing Config settings for End Device Frame Buffering	( SCGCQ00123628 ) 
 - Gen 3: remove Release On Full option for diag trace buffer( SCGCQ00125496 ) 
 - MPI2: review Task Set Full handling	( SCGCQ00125662 ) 
 - Gen 3: add 12Gb/s option for link rate( SCGCQ00125672 ) 
 - MPI2: add Link Rate of UNSUPPORTED_PHY_ATTACHED	( SCGCQ00125683 ) 
 - [Internal Use Only] Control of Loopback mode through the UART( SCGCQ00126580 ) 
 - Add basic support for new hardware block state timers in SAS core blocks	( SCGCQ00127730 ) 
 - Modify mfg page 3 to incorporate back channel training.( SCGCQ00131013 ) 
 - pl: Power condition support in SATL - mode page 0x1A	( SCGCQ00131186 ) 
 - pl: Power condition support in SATL: Start/Stop Unit	( SCGCQ00131188 ) 
 - Allow Config Write Current of Manufacturing Page 5 after PortEnable	( SCGCQ00131631 ) 
 - Update the Quiesce IO/TM/SMP code for gen3 generic availability	( SCGCQ00131981 ) 
 - Thunderbolt: The B0 revision handles the SAS clock setup differently.( SCGCQ00132812 ) 
 - Customer Liberator Design without DDR2 requires IT firmware config option to power down/not use DDR2 Controller( SCGCQ00133967 ) 
 - Firmware build needs to link pre-built DDR library, instead of compiling it with the rest of firmware( SCGCQ00134473 ) 
 - (IOP-Only( SCGCQ00135183 ) 
 - (NVDATA	( SCGCQ00136652 ) 
 - Gen3: Changes to support 4port bond option( SCGCQ00136691 ) 
 - Gen3 PwrMgmt: Add IOP & PL infrastructure for chip-wide power management modes( SCGCQ00136946 ) 
 - Gen3 PwrMgmt: Add IOP support for PCIe Dynamic Power Allocation (DPA	( SCGCQ00136955 ) 
 - MPI2: bring Diagnostic Data Upload Tool forward from MPI v1.5( SCGCQ00137489 ) 
 - Thunderbolt B0: Update SBR( SCGCQ00138057 ) 
 - Add ability to disable Liberator Bugtrack [Nova] 540 workaround( SCGCQ00139949 ) 
 - (Non-FPGA Only( SCGCQ00141231 ) 
 - (FPGA-Only( SCGCQ00141569 ) 
 - Disable SASAllInts Interrupts going to the host through PCI-E( SCGCQ00141627 ) 
 - Invader: Incorporate Colt EDS 1.1 support for modified QM registers.	( SCGCQ00141765 ) 
 - Ensure RX DMA IO cleanup matches latest Colt EDS 1.1	( SCGCQ00141768 ) 
 - MPI2: ability to disable SATA NCQ on a per-device basis	( SCGCQ00141834 ) 
 - (IOP-Only( SCGCQ00141859 ) 
 - TxDMA error handling update for NonAuto Bit implementation( SCGCQ00141867 ) 
 - Gen3: Change SAS2HW_CHIP_ID to SASHW_CHIP_ID	( SCGCQ00142520 ) 
 - MPI2: obsolete MPI2_IOUNITPAGE1_MULTI_PATHING( SCGCQ00142578 ) 
 - Updates to makefile for gen3	( SCGCQ00143642 ) 
 - GENCRC: Update build enviornment to new toolset( SCGCQ00144028 ) 
 - Gen3 Task Mgmt Debuggability & Testability Improvements( SCGCQ00144418 ) 
 - convert pliDevHandleFind( SCGCQ00144456 ) 
 - Update PPC ticks to reflect new clock speed in Invader FPGA( SCGCQ00144514 ) 
 - Add support for LD state table in Cuda( SCGCQ00144627 ) 
 - Add UART command to send down a PLI control request	( SCGCQ00145596 ) 
 - change FPE exception INVALIDE_DESCRIPTOR handling from doing an error reply to just handing off to IOP( SCGCQ00146110 ) 
 - Trident: Update firmware to EDS 1.01	( SCGCQ00146112 ) 
 - Update FW to match Invader EDS v1.3	( SCGCQ00147317 ) 
 - Reserved MID 0x1 for special use	( SCGCQ00147930 ) 
 - Updates to Trident( SCGCQ00147952 ) 
 - New MMU management functions for PPC476( SCGCQ00148628 ) 
 - Implement proper memory map translation for DMA'ing data to/from host/IOC( SCGCQ00148721 ) 
 - add rom image to release build file( SCGCQ00148737 ) 
 - txdma cleanup changes from Colt EDS 1.21	( SCGCQ00149016 ) 
 - TBM: Host posted Extended Buffer has to be 16KB aligned	( SCGCQ00149045 ) 
 - Add additional PPC476 MMU utility functions to support boot loader( SCGCQ00149224 ) 
 - PALLADIUM: Allow the spurious interrupt workaround to work for palladium build as well.( SCGCQ00149231 ) 
 - Add an RMTFLASH script to program a BIOS image into FLASH( SCGCQ00149685 ) 
 - add PLI control request support for Vendor Specific case 1( SCGCQ00149688 ) 
 - add PLI control request support for FPE Config 3 FpUseLdTableFlags bit( SCGCQ00149689 ) 
 - FPE: need to add an additional flags parameter to pliStartScsIO(	( SCGCQ00151001 ) 
 - First Set of Invader/Elektra DDR3 changes( SCGCQ00151263 ) 
 - Add code to initialize Elektra Memory System on FPGA	( SCGCQ00153736 ) 
 - Gen3 IR - Selectable Consistency Checking( SCGCQ00154734 ) 
 - Implement Extended Manufacturing Page 40 and 41. These two pages replace mfg page 3.	( SCGCQ00155477 ) 
 - DevTest: Timer services test code checkin( SCGCQ00156252 ) 
 - FPGA: Update current FPGA build configuration to better match current state of the FPGA( SCGCQ00157831 ) 
 - MPI2: Add new Config Page Type - Extended Manufacturing( SCGCQ00157968 ) 
 - MPI 2.5: Chain SGL Segment sizes	( SCGCQ00157982 ) 
 - Change Trident FMU address macros to match correct hardware address decodes( SCGCQ00159978 ) 
 - Obsolete Man Page 15	( SCGCQ00159985 ) 
 - Implement functional section changes as per Colt EDS 1.3.( SCGCQ00160464 ) 
 - MPI2: Change MPI Simple SGE Local bit description and IEEE Chain Flags to match HW( SCGCQ00160485 ) 
 - TBM: Enable TBM by default in all builds	( SCGCQ00160594 ) 
 - TBM: Dump the TraceBuffer entries on FW Fault( SCGCQ00160595 ) 
 - Include debug strings in diag buffer	( SCGCQ00161332 ) 
 - FPE: implement start pending IO function for FPE devices	( SCGCQ00161456 ) 
 - Update resource allocation parameters in NVDATA( SCGCQ00161657 ) 
 - MPI2: Add IOC Temperature Monitoring Capability( SCGCQ00161661 ) 
 - Add support for both MPI & IEEE SGLs in IR's Configuration Request Message support( SCGCQ00162072 ) 
 - MPI2: rework Pinout field of ConnectorInfo for MFG Page 7( SCGCQ00162562 ) 
 - TBM: Set TraceType for devices from host	( SCGCQ00162901 ) 
 - Add L3 cache support	( SCGCQ00163170 ) 
 - MPI2: IOUnit page 7: Add new fields for Board temperature( SCGCQ00163413 ) 
 - MPI 2.5: SCSI Initiator I/O path counters (SAS IO Unit Page 16( SCGCQ00163641 ) 
 - Add UART command to determine if the IOC is in fault state( SCGCQ00163729 ) 
 - TBM: Add debug code for TBM errors( SCGCQ00164570 ) 
 - PL Light: add pliLight equivalent for get mid state table info( SCGCQ00165286 ) 
 - MPI2: new event for NOTIFY(Enable Spinup	( SCGCQ00166171 ) 
 - Implement new Atomic ECC scrub feature( SCGCQ00167136 ) 
 - Add PLI control request to specify power management modes for Cuda fast path engine.	( SCGCQ00167819 ) 
 - FPE: remove Cuda timer if IO is timed by cuda and TM aborts it( SCGCQ00168251 ) 
 - FPE: changes to ioflags usages for reply destination and ignore context	( SCGCQ00168410 ) 
 - Round 5 of gen2 WA removal( SCGCQ00168602 ) 
 - MPI 2.5: remove Command Determines Data Direction bit from SCSI IO	( SCGCQ00169936 ) 
 - FPE: TM abort list should be checked when handlign Cuda Timer Wheel timeouts	( SCGCQ00169942 ) 
 - Remove support for SAS3108_3 and SAS3108_4 chip types( SCGCQ00170560 ) 
 - Gen3: RAID Accelerator changes( SCGCQ00171770 ) 
 - add support for new IocFactsReply.IOCMaxChainSegmentSize field( SCGCQ00171810 ) 
 - Gen3 IR - Remove BT1680 work around from IR	( SCGCQ00172046 ) 
 - Update Ethernet software to work with the Invader controller	( SCGCQ00172834 ) 
 - MPI2: for SRIOV, allow PF to access config pages for other VFs( SCGCQ00172984 ) 
 - Gen3: FW support for PowerPC Instruction Trace (ITRACE( SCGCQ00173574 ) 
 - Add PLI defnies for FPE Power Savings modes( SCGCQ00173648 ) 
 - Implement new FLASH layout for Invader( SCGCQ00175740 ) 
 - MPI2: method to communicate between hosts on virtual functions( SCGCQ00175743 ) 
 - Firmware handling for non-good response frame to halt SAS Core and disable Fast Path Engine( SCGCQ00176261 ) 
 - MPI 2.5: new Power Performance Change Event to report changes to global power management mode( SCGCQ00176893 ) 
 - Gen3: USB( SCGCQ00177075 ) 
 - SAS-3 FW Build - Accommodate Scrutiny( SCGCQ00177124 ) 
 - MPI 2.5: report offset of first EEDP error in SCSI IO Reply( SCGCQ00177635 ) 
 - Update RxCtxMgr Cleanup to match new gen3 hardware functionality	( SCGCQ00178840 ) 
 - Further clean-up of linker directive files in preparation for Invader silicon( SCGCQ00179257 ) 
 - HW WA for BT COSEDA 790 - setup starfish regs as the HW defaults are incorrect( SCGCQ00179616 ) 
 - Remove [SAS2Core] 1656( SCGCQ00180309 ) 
 - PL: allow each phy to initialize its electrical parameters from the proper phy group	( SCGCQ00181727 ) 
 - FPE: disable FPE Timer when faulting	( SCGCQ00181784 ) 
 - Handle new RxCtxManager interrupt in B0	( SCGCQ00183299 ) 
 - Gen3 Nightly Build : Make the necessary changes in the overnight build copy perl file for gen3( SCGCQ00183622 ) 
 - Update Invader eval board SBR settings in NVDATA	( SCGCQ00183907 ) 
 - Change frequency for internal UART clock to match silicon( SCGCQ00184806 ) 
 - Set up PIM2 to allow access to expansion ROM	( SCGCQ00185739 ) 
 - FPE: Add PLI interface to allow IOP to write MSindex, VF_Id and SMID into Cuda's MST	( SCGCQ00187301 ) 
 - Update controller clock divider setup for Invader silicon.( SCGCQ00187961 ) 
 - Update Default NVData to Run Invader at 1GHz	( SCGCQ00188063 ) 
 - Invader Ethernet Updates	( SCGCQ00188150 ) 
 - Gen3 PwrMgmt: Wide Port Power Management to support 'Communicated Intent Modulation Scheme'( SCGCQ00188249 ) 
 - Update TFTP Firmware Download for Invader( SCGCQ00192532 ) 
 - Need a PLI control request to get the SAS core version( SCGCQ00192893 ) 
 - Changes to IOP firmware in order to support DDR	( SCGCQ00193790 ) 
 - Update iop pci reg to print FMU registers( SCGCQ00194247 ) 
 - MPI2: product specific range for extended image type	( SCGCQ00194293 ) 
 - MPI2: Add auto reserve and 8-kbit seeprom support to ISTWII( SCGCQ00194461 ) 
 - ONFI: Controller Initialization	( SCGCQ00194672 ) 
 - ONFI: Prepare Bad Block List	( SCGCQ00194674 ) 
 - ONFI: Restore offloaded data on boot up from NAND flash( SCGCQ00194677 ) 
 - 3rd set of DDR3 library changes	( SCGCQ00198958 ) 
 - Update TM to have a "marker" mid for the Colt->Cuda completion Queue	( SCGCQ00199733 ) 
 - New serdes settings from SE	( SCGCQ00200293 ) 
 - Make SMP requests high priority and ensure they don't get queued behind other contexts( SCGCQ00200476 ) 
 - DDR3 library global structure for training values is too large( SCGCQ00201056 ) 
 - MPI2: Remove/Obsolete MPI Power Management Control Feature PCIE_LINK	( SCGCQ00201203 ) 
 - MPI2: Add spin-up disable bit to SAS IO Unit Page 4	( SCGCQ00201727 ) 
 - Replace call to BIST with call to cache zero	( SCGCQ00202468 ) 
 - Add FW support for new B0 RxFM/RxCM"WrongDataDirection interrupts( SCGCQ00202861 ) 
 - Gen3: MPI PowerManagementControl request msg parameters need to verified before processing.( SCGCQ00203386 ) 
 - Change Clear/Set IO Unit State to use atomic processor instructions	( SCGCQ00203396 ) 
 - Customer requests change to DDR3 library interface function iopiDelayUSec( SCGCQ00203665 ) 
 - Add a wrapper around iopiDelayUSec for call from DDR3 library( SCGCQ00203667 ) 
 - MPI2: New RAID Action (COMPATIBILITY_CHECK( SCGCQ00203886 ) 
 - Change to register settings from SE validation( SCGCQ00204041 ) 
 - Support to handle Unconfirmed Responses reported by SAS HW( SCGCQ00205974 ) 
 - Changes to better support highest speeds	( SCGCQ00206640 ) 
 - Support latest revision of JEDEC SPD	( SCGCQ00207165 ) 
 - Gen3 IR - Optimize resync buffer size for enhanced resync performance on Gen3 controllers.( SCGCQ00207724 ) 
 - Gen3 IR - Optimize IR code( SCGCQ00208291 ) 
 - MPI2: Return Port info in the SAS Device Status Change Event	( SCGCQ00209048 ) 
 - MPI2: create product-specific range for RAID Action Request( SCGCQ00209055 ) 
 - Update chip recognition code so that it will identify all chip types	( SCGCQ00209388 ) 
 - ONFI: Add UART commands to test ONFI MAP Commands( SCGCQ00209640 ) 
 - Invader Performance: Do not allocate FPE queue when disabled	( SCGCQ00209915 ) 
 - Need a mechanism to enable snoop regions in SAS	( SCGCQ00210177 ) 
 - ONFI: Updates to ONFI UART commands	( SCGCQ00210291 ) 
 - Add MR build types to "bld31xxgnu" and to the "all" build( SCGCQ00210495 ) 
 - Disable SSC for all speed( SCGCQ00210602 ) 
 - PL: check in new serdes settings	( SCGCQ00213218 ) 
 - ONFI: Update batch file for release( SCGCQ00213281 ) 
 - ONFI: Enable ONFI interrupt and add UART commands( SCGCQ00215328 ) 
 - Invader PLB snoop region configuration( SCGCQ00215430 ) 
 - MPI2: new name for SCSI IO Request Control bits( SCGCQ00218764 ) 
 - Add an UART cmd line to toggle the testmux pins( SCGCQ00219300 ) 
 - Bit field name change to CCR Module-Specific Resets 1 register (changed in Invader EDS v2.2( SCGCQ00219840 ) 
 - Enclosure Management Changes for Direct Attached SEP	( SCGCQ00221114 ) 
 - Invader A0: Hardware Workaround to support proper VfEnable handling in FPE hw during MUR	( SCGCQ00221352 ) 
 - Invader Performance Improvements (Part 1	( SCGCQ00221359 ) 
 - Create new API for user to set up entry into Memory Controller Low Power modes( SCGCQ00222557 ) 
 - Combine Big and Little Endian Binary releases into a single generic non-source release( SCGCQ00222561 ) 
 - Invader A0: optimize prints to disable io printing when TBM is enabled( SCGCQ00222985 ) 
 - Invader A0 PL FPE Start IO performance optimzation( SCGCQ00223252 ) 
 - Update TxFM cleanup code for gen3( SCGCQ00224494 ) 
 - Updates to new SnC Method from HW.( SCGCQ00224783 ) 
 - Gen3 IR - Implement Raid Action to allow drivers to enable firmware fast path( SCGCQ00227402 ) 
 - ONFI: Interface function name changes( SCGCQ00227457 ) 
 - Additional XML Schema Changes.( SCGCQ00227512 ) 
 - MPI 2.6 Add Atomic Request Descriptor capability	( SCGCQ00227735 ) 
 - Invader: Update PCIe Core for EDS 1.03( SCGCQ00227979 ) 
 - MPI2: add 4K sectors supported bit to IOC Page 6 CapabilitiesFlags field	( SCGCQ00228572 ) 
 - MPI2: BIOS Page 1 additions for UEFI HII	( SCGCQ00229719 ) 
 - Make DDR3 fault codes unique	( SCGCQ00229872 ) 
 - Invader: Enable Machine Check Interrupts	( SCGCQ00234935 ) 
 - Initialize Port Layer Settings such as ALF bit and Port Link Availability initial count from Man Page 17	( SCGCQ00237340 ) 
 - (SAS3 IR	( SCGCQ00237718 ) 
 - ONFI: Mirroring ONFI Flash( SCGCQ00239455 ) 
 - ONFI: Add api for getting memory required for bad block list	( SCGCQ00239699 ) 
 - Investigate a method to have PL always turn FPE back on at the end of TM	( SCGCQ00242895 ) 
 - ONFI: Enhance the failure status reporting in ONFI Library( SCGCQ00245401 ) 
 - Invader: Update Ethernet clock configuration to use external clocks( SCGCQ00246665 ) 
 - IOP: Fault on PCI-Express Interrupt PLB RW Processor Error( SCGCQ00246666 ) 
 - IOP: Support different SBD size in GET_SERIAL_BOOT_DATA_SIZE( SCGCQ00246872 ) 
 - ONFI: Consistency in Channel and Bank naming	( SCGCQ00250933 ) 
 - IOP Cli: Show IOP Message context( SCGCQ00251001 ) 
 - A modified IT controller firmware build is needed in order to test Fastpath IO Timer functionality( SCGCQ00254775 ) 
 - ONFI: Offload and Restore Performance Improvement( SCGCQ00255129 ) 
 - ONFI mirroring APIs need to work for only a single Channel.( SCGCQ00255918 ) 
 - (IOP	( SCGCQ00257882 ) 
 - MPI v2.6: Additional request and reply descriptor formats( SCGCQ00259613 ) 
 - Invader A0: (PL	( SCGCQ00261860 ) 
 - Update B0 WA matrix for all fixed FPE issues	( SCGCQ00261863 ) 
 - [USB]: BT [invader]1682 : Implement workaround for ULPI PHY reset sequence( SCGCQ00262724 ) 
 - (NVDATA	( SCGCQ00263859 ) 
 - MPI 2.6: SOP Encapsulated request( SCGCQ00264755 ) 
 - MPI 2.6: NVMe Encapsulated request( SCGCQ00264759 ) 
 - IOP: Update the IOP Workaround table for B0	( SCGCQ00265859 ) 
 - Parameter swap_port_rw_same_en not supported in DDR Memory Controller( SCGCQ00268568 ) 
 - Allow for MPI 2.5 IEEE Chain Element in SATA Passthrough Request	( SCGCQ00268818 ) 
 - IOP: Reorganize the code where firmware copies the code from flash to DDR to make it more readable( SCGCQ00269227 ) 
 - Change handling of silicon revision and add B0 support( SCGCQ00271076 ) 
 - NVDATA: Enable Back Channel Training by default in nvdata( SCGCQ00271106 ) 
 - IOP: Disable power loss interrupt( SCGCQ00277808 ) 
 - Add comments to ddrifault.h( SCGCQ00278372 ) 
 - Gen3 IR - Enable PI support in NVDATA for 3004 and 3008( SCGCQ00280131 ) 
 - New Serdes settings that meet the spec requirement	( SCGCQ00283165 ) 
 - Toolbox Diagnostic CLI Request now uses IEEE SGL, including chain elements( SCGCQ00283196 ) 
 - MPI2: Toolbox Diagnostic CLI Tool Request may now use chain elements in the SGL( SCGCQ00283198 ) 
 - Added Cable Management file to PL makefile( SCGCQ00284543 ) 
 - Post-training compensations for an imbalance in the setup/hold timing( SCGCQ00289581 ) 
 - Disabled FW chain pull code in IR.( SCGCQ00290601 ) 
 - MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request( SCGCQ00294055 ) 
 - MPI 2.6: update SGL chapter to include PCIe	( SCGCQ00294131 ) 
 - Enabled Parity Checking for L2 Cache	( SCGCQ00295557 ) 
 - Add argument in ONFI Restore APIs to pass RestoreTimeoutValue( SCGCQ00298497 ) 
 - MPI2: add IOCExceptions bit for Partial Memory Failure( SCGCQ00299943 ) 
 - Add 2 new fault conditions.( SCGCQ00304933 ) 
 - Modify mfg11 so it's the same size as gen2( SCGCQ00307672 ) 
 - Update legacy DCR assembly instructions to use new indexed instructions( SCGCQ00307945 ) 
 - MPI2: IR reporting Elapsed Seconds( SCGCQ00308453 ) 
 - PL: Enable back channel training for controller phys.( SCGCQ00321647 ) 
 - (IOA	( SCGCQ00323012 ) 
 - New DDR3 library API to obtain ECC information and return it to the caller( SCGCQ00333267 ) 
 - MPI 2.6: PCIe IO Unit Page 0 & 1 definitions	( SCGCQ00336383 ) 
 - Invader C0: Combined Reply Queue Feature	( SCGCQ00337165 ) 
 - MPI2: Add TargetModeAbort by initiator device handle	( SCGCQ00337167 ) 
 - MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors( SCGCQ00338506 ) 
 - Modify firmware to work with Combined Reply Q Mode( SCGCQ00340458 ) 
 - SCSI to NVMe dataset management translations	( SCGCQ00341219 ) 
 - MPI2: Add new TargetModeAbort AbortType to only abort Command IUs( SCGCQ00345215 ) 
 - MPI 2.6: add IO Unit Control Request	( SCGCQ00345258 ) 
 - MPI 2.6: add PCIe Event Data (Generic( SCGCQ00345260 ) 
 - MPI 2.6: PCIe Topology Change List Event	( SCGCQ00345266 ) 
 - MPI 2.6: PCIe Switch Config Pages( SCGCQ00345270 ) 
 - MPI 2.6: add PCIe Device Config Pages( SCGCQ00345271 ) 
 - MPI 2.6: PCIe Link Config Pages	( SCGCQ00345272 ) 
 - MPI 2.6: Enclosure Management( SCGCQ00345273 ) 
 - Additional SCSI to NVMe translations	( SCGCQ00345822 ) 
 - (FPGA( SCGCQ00352412 ) 
 - Device Info field for PCIe devices( SCGCQ00353339 ) 
 - (IOP	( SCGCQ00356717 ) 
 - MPI2: Use Slot Information during Port Enable Event Replay option( SCGCQ00356796 ) 
 - MPI2: Add OEM Identifier to BIOS Page 1	( SCGCQ00357228 ) 
 - SATA FIS Porting feature support	( SCGCQ00357509 ) 
 - MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply( SCGCQ00357551 ) 
 - SAS Gen3.5 FW Spinup Control Implementation( SCGCQ00360815 ) 
 - MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request( SCGCQ00360843 ) 
 - MPI 2.6: new family values for ProductID fields( SCGCQ00360952 ) 
 - Modify ddriGetCurrentEccErrorInfo API( SCGCQ00361251 ) 
 - Add memport error register definitions to the memport header file currently distributed with library.( SCGCQ00361253 ) 
 - (STANG( SCGCQ00362507 ) 
 - [Dauntless]: SGL Translation - IEEE-64 to SOP/PQI( SCGCQ00362773 ) 
 - Added new internal tool, no change to FW	( SCGCQ00362950 ) 
 - MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11( SCGCQ00363600 ) 
 - (IOP	( SCGCQ00367858 ) 
 - Backend PCIe device memory allocation (part 2( SCGCQ00372536 ) 
 - Added support for async removal and insertion for PCIe devices.( SCGCQ00377853 ) 
 - (NVDATA( SCGCQ00378825 ) 
 - Added support for handling new Stang exceptions( SCGCQ00379989 ) 
 - USB : BT [invader]1653 :ULPI Function Control Register Write gets corrupted by a Soft Reset( SCGCQ00380011 ) 
 - pl: pci: DevHandle allocation for PCI switches( SCGCQ00380149 ) 
 - (IOA	( SCGCQ00381819 ) 
 - This week's NVMe related changes	( SCGCQ00383672 ) 
 - Allow Protection Information bit for IR Volume Create( SCGCQ00385306 ) 
 - (IOP	( SCGCQ00391086 ) 
 - MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply( SCGCQ00396414 ) 
 - Modified address space bits	( SCGCQ00397136 ) 
 - MPI 2.6: Add PCIe IO Unit Page 4	( SCGCQ00397563 ) 
 - MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs	( SCGCQ00397568 ) 
 - MPI 2.6: Add board power fields to IO Unit Page 7( SCGCQ00397572 ) 
 - MPI 2.6: Add support for SAS Persistent Connections( SCGCQ00397577 ) 
 - Additional diag console commands	( SCGCQ00398216 ) 
 - MPI 2.6: Add NVMe SGL support( SCGCQ00398256 ) 
 - FW Read/Write IO Path base functionality	( SCGCQ00400466 ) 
 - FW Read/Write IO Path - NVME Helper functions( SCGCQ00400467 ) 
 - FW Read/Write IO Path - AHCI helper functions( SCGCQ00400472 ) 
 - FW Read/Write IO Path - Additional PCI protocol Helper functions	( SCGCQ00400473 ) 
 - No firmware change, tool change only	( SCGCQ00400547 ) 
 - Use generic IO context structure throughout the NVMe code( SCGCQ00400554 ) 
 - NVMe: Update NVMe non read write translations( SCGCQ00401386 ) 
 - Added code to support new high order bits register for scripts physical addresses( SCGCQ00406167 ) 
 - (IOP	( SCGCQ00412128 ) 
 - New debug information -- dumping of AHCI registers	( SCGCQ00412145 ) 
 - MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag	( SCGCQ00414050 ) 
 - Test code for sending large reads and writes	( SCGCQ00415461 ) 
 - MPI 2.5: Toolbox Console Text Display Tool( SCGCQ00415512 ) 
 - Add PLI control request for getting host memory page size( SCGCQ00418127 ) 
 - SAS Gen3.5 Additional PCI Encapsulated MPI Message Support( SCGCQ00418649 ) 
 - Firmware Support for NVMe encapsulated MPI message( SCGCQ00420063 ) 
 - Add base PCIe Task Management and AHCI device Task Management support( SCGCQ00420317 ) 
 - Update iopiMemoryMove( SCGCQ00420399 ) 
 - Added support for translating PLB/DDR addresses in simple SGEs for AHCI devices( SCGCQ00420512 ) 
 - (PL	( SCGCQ00420887 ) 
 - Added code to reject firmware translation of chain to AHCI PRDT format( SCGCQ00421777 ) 
 - Add ALADIN tracing support in PL	( SCGCQ00423378 ) 
 - (IOA	( SCGCQ00425000 ) 
 - MPI 2.6: Add NVMe SGL support to IEEE SGL( SCGCQ00432541 ) 
 - MPI 2.6 Rev. B Feature Section 17.3.20.3: Add support for PCIe Device Page 2	( SCGCQ00432568 ) 
 - PCIe IO Unit Page 1 NVMe Max Queue Depth	( SCGCQ00432741 ) 
 - MPI 2.6 Rev. B Feature: Move all SAS IO Unit Page 4 Spinup Control and PortEnable functionality to IO Unit Page 11.( SCGCQ00433597 ) 
 - Dauntless FPGA: Unable to initialize with MSI-X enabled( SCGCQ00436413 ) 
 - Need better way to set up PDB POMs( SCGCQ00436942 ) 
 - Add Stang Exception error handling for SOP( SCGCQ00441252 ) 
 - Added IO Unit Control Request in MPI v2.6 B to replace existing SAS IO Unit Control Request( SCGCQ00443274 ) 
 - MPI 2.6 Rev. B Feature: Section 17.3.2.8: Added BoardPowerRequirement and PCISlotPowerAllocation fields to IO Unit Page 7.( SCGCQ00443278 ) 
 - Implementation of SATL handling while the SATA drive is in security 'frozen' state( SCGCQ00443282 ) 
 - Added PCIe IO Unit Page 4.( SCGCQ00443286 ) 
 - SAS3.5: Move ALADIN HW defines and register structures to separate header file under \common\hw.	( SCGCQ00448020 ) 
 - Handle PCIe Fx-FPE completion queue wrapping while manually adding TM entries.( SCGCQ00449817 ) 
 - NVMe: Start device initialization earlier	( SCGCQ00449822 ) 
 - Dauntless FPGA: Slight reset behavior modification	( SCGCQ00451177 ) 
 - Dauntless FPGA: Allow standard DDR3 training to run if DDR is enabled in Manufacturing Page 11( SCGCQ00453573 ) 
 - New IOP Interface to allow mapping of larger memory resources (>1G	( SCGCQ00455575 ) 
 - AHCI: Add handlers for IO and port errors( SCGCQ00459853 ) 
 - AHCI: Add handlers for requester/completer errors( SCGCQ00459876 ) 
 - MPI 2.6: System Interface Register Set update( SCGCQ00464402 ) 
 - MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses( SCGCQ00466819 ) 
 - MPI 2.5: Signed images for FWDownload( SCGCQ00469990 ) 
 - MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps"( SCGCQ00471293 ) 
 - Rudimentary Advanced Error Reporting support	( SCGCQ00473858 ) 
 - Update PQI and SOP header files to latest revision( SCGCQ00474533 ) 
 - Create and use generic PCI and PCI Express headers( SCGCQ00477114 ) 
 - Ventura: NVMe: Shutdown notification for NVMe devices.( SCGCQ00477716 ) 
 - MPI 2.5: add reserved fields to IO Unit Page 7 for future use( SCGCQ00477817 ) 
 - IOP: Special MSI/ MSIx error interrupt fault	( SCGCQ00478193 ) 
 - Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request( SCGCQ00480292 ) 
 - Ventura: PL Dual/Multiple Iop Completion Queue (MR-11( SCGCQ00481273 ) 
 - Ventura: Trace Buffer Manager Updates - Extended Mode (DMA( SCGCQ00481274 ) 
 - Encl Mgmt: Support for the new PBAM LED control and SGPIO HW block( SCGCQ00490950 ) 
 - Ventura: Investigate Performance Monitors( SCGCQ00492549 ) 
 - SOP: Base device error handling for IO exceptions( SCGCQ00494457 ) 
 - MPI 2.6: shutdown operation for IO Unit Control Request( SCGCQ00496998 ) 
 - SAS Gen3.5 Additional PCI Encapsulated MPI Message Support - Additional Fixes( SCGCQ00498556 ) 
 - PL: SOP/PQI Task Management support( SCGCQ00521567 ) 
 - Ventura: Combo Serdes Wrapper Support( SCGCQ00521573 ) 
 - Ventura: Silicon Address Map Changes	( SCGCQ00521681 ) 
 - Ventura: Update CCR Register Definitions	( SCGCQ00521691 ) 
 - Ventura: Remove XMEM	( SCGCQ00522458 ) 
 - Ventura: IOA – Impala IO Accelerator Cuda Trace Buffer Manager Block Bring Up( SCGCQ00522532 ) 
 - Identify physical location of a target device( SCGCQ00523879 ) 
 - Ventura: DRAM Memory Controller - Preliminary DDR4 Support( SCGCQ00527826 ) 
 - Enterprise: header file( SCGCQ00552408 ) 
 - Enterprise PIM/POM setup	( SCGCQ00552409 ) 
 - Enterprise: register usage and indexing in the backend PCIe code( SCGCQ00552412 ) 
 - Enterprise: base core initialization	(SCGCQ00552422 ) 
 - Ventura: Enterprise: toplevel interrupt handler	( SCGCQ00552429 ) 
 - Ventura: Enterprise: sub-block interrupt handling infrastructure	( SCGCQ00552432 ) 
 - Enterprise: backend device interrupt configuration and handling	( SCGCQ00552447 ) 
 - Enterprise: root complex changes, part 1	( SCGCQ00552480 ) 
 - Ventura: Update Product ID	( SCGCQ00563371 ) 
 - NVMe: Extended Inquiry Data VPD page	( SCGCQ00563906 ) 
 - MPI 2.6: Add supported link rates and widths for PCIe devices( SCGCQ00564281 ) 
 - Port PL and CFGI library builds to ARM for Ventura( SCGCQ00564814 ) 
 - Add type BIOS for HashImageType.	( SCGCQ00566306 ) 
 - MPI 2.0: Add product-specific Flag bit to Clean Tool	( SCGCQ00569175 ) 
 - Port SPI library build to ARM( SCGCQ00570147 ) 
 - NVMe: Support for Mode Sense (10	( SCGCQ00571441 ) 
 - Ventura: Add support for new interrupts in Raptor SAS core( SCGCQ00572622 ) 
 - MPI 2.6: Add additional NVMe AccessStatus codes	( SCGCQ00574070 ) 
 - Change armCache functions and header files to armMmu	( SCGCQ00574345 ) 
 - MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually( SCGCQ00574358 ) 
 - Modify MPI FLASH Layout for Ventura( SCGCQ00574364 ) 
 - Increase layout size for DAUNTLESS build to 1.5MB as the image size has grown too large( SCGCQ00574367 ) 
 - Create initial build of IOP for ARM( SCGCQ00577404 ) 
 - Port Ethernet Library to ARM	( SCGCQ00579966 ) 
 - Hardware Workaround Matrix For Ventura IOP layer( SCGCQ00586265 ) 
 - SAS3.5 DAUNTLESS: Implement rmtflash for SPI Flash in Dauntless	( SCGCQ00593527 ) 
 - Ventura: Create Ventura XSD and other NVDATA files( SCGCQ00594077 ) 
 - Update Intruder SBR and PCIe SerDes settings	( SCGCQ00598439 ) 
 - SpiLib enahancement( SCGCQ00598956 ) 
 - MPI 2.6: Add BootFlags field to Firmware Image Header( SCGCQ00601869 ) 
 - Intruder: TLB changes to match new top-level address map of FPGA bitstream release 1	( SCGCQ00603459 ) 
 - Intruder top-level interrupt map for FPGA Bitstream Release 0.5	( SCGCQ00603463 ) 
 - Remove usage of FWDebugAreaBaseAddress from PLI_SET_SOD_PARAMS( SCGCQ00603490 ) 
 - PL: Determine the number of SAS Cores present( SCGCQ00603493 ) 
 - add Intruder FPGA build	( SCGCQ00604632 ) 
 - Ventura: POC7 Map Update	( SCGCQ00606237 ) 
 - Ventura: DRAM Memory Controller - Heterogeneous Rank Support	( SCGCQ00606241 ) 
 - SATL: Changes to SCSI Format Unit translation( SCGCQ00606271 ) 
 - MSS: Initial Code Import	( SCGCQ00606274 ) 
 - Ventura: Firmware connect appropriate FLASH routines to SPI	( SCGCQ00606312 ) 
 - Intruder: review usage of #if DAUNTLESS in start-of-day code	( SCGCQ00606374 ) 
 - Allow for separate Ventura and Intruder versions	( SCGCQ00610916 ) 
 - Ventura: SAS Persistent Connection support( SCGCQ00612657 ) 
 - Ventura: SAS Initiate Close support	( SCGCQ00612661 ) 
 - Modify basetype.h to be device independent( SCGCQ00612747 ) 
 - Ventura: Ventura Temperature Monitor Support	( SCGCQ00612780 ) 
 - Speed up bld31xxgnu all	( SCGCQ00616571 ) 
 - Intruder: IOP interrupt map (Release 1.0	( SCGCQ00617602 ) 
 - Intruder: Update gIopHwDevId and gMpi2SupportedDevices( SCGCQ00619370 ) 
 - MPI 2.6: Add new FLASH region types( SCGCQ00619371 ) 
 - Create xml and xsd files for Intruder( SCGCQ00619416 ) 
 - Intruder: Update SBR	( SCGCQ00619417 ) 
 - Intruder: IOP changes for FPGA bringup( SCGCQ00619448 ) 
 - PL: update SAS Core DCR interface for multiple SAS cores	( SCGCQ00620384 ) 
 - PL bringup on Intruder FPGA( SCGCQ00620516 ) 
 - Intruder FPGA updates( SCGCQ00621476 ) 
 - Investigate iopSODCheckPcePimSizes(	( SCGCQ00621483 ) 
 - MPI 2.6: Added an additional signature value for the firmware image header( SCGCQ00623271 ) 
 - Removed gplPciDeviceDma( SCGCQ00628093 ) 
 - Intruder: adding build command files	( SCGCQ00628333 ) 
 - Enterprise: allocate memory at SOD for generic message data queue( SCGCQ00629194 ) 
 - Modified NVMe code to use new safe accessor functions for PCIe read/write.( SCGCQ00630198 ) 
 - Ventura PBAM(Vayu( SCGCQ00631219 ) 
 - Updated IOP interrupt handler function to handle multiple SAS Cores.	( SCGCQ00632495 ) 
 - Update PLI_SET_SOD_PARAMS as per new PLI spec( SCGCQ00637694 ) 
 - PL-only: Provide support for CloseOptimize in PL	( SCGCQ00638922 ) 
 - Modified AHCI error handling to use new safe accessor functions for PCIe read/write(SCGCQ00639213 ) 
 - Add ALADIN support to Ventura.( SCGCQ00642196 ) 
 - NVMe: several SCSI-NVMe related changes( SCGCQ00642831 ) 
 - Ventura: SIO/LED control enable PCI/SAS device activity support( SCGCQ00642853 ) 
 - UTILITY: Add memcfg utility for ARM products	( SCGCQ00642860 ) 
 - Intruder: Intregrate with new DDR3 library( SCGCQ00644369 ) 
 - Ventura: ARM Generic Timer Integration( SCGCQ00644382 ) 
 - IOP: MCTP over I2C updates for Ventura class hardware( SCGCQ00644461 ) 
 - Ventura: POC8C Bringup( SCGCQ00646636 ) 
 - Ventura: Local Chain Support (CR-15	( SCGCQ00647786 ) 
 - Update usage of IOC_NUM_PHYS	( SCGCQ00649610 ) 
 - Ventura: Change readPIR(	( SCGCQ00652365 ) 
 - Ventura: MSS - Hybrid MRAM DIMM SPD Conversion Interface Function( SCGCQ00652983 ) 
 - Updates for FPGA phase 0.3	( SCGCQ00654885 ) 
 - Ventura: Enterprise: revisit base core init	( SCGCQ00655157 ) 
 - Incorporate DDR4 RDIMM functionality.( SCGCQ00655293 ) 
 - Ventura: Create initial A57 A64-Booting Image( SCGCQ00656357 ) 
 - Intruder: Remap SASCORE1 in virtual address space with no overlap( SCGCQ00660501 ) 
 - Modify Diag commands to handle multiple SAS core.( SCGCQ00661114 ) 
 - Move PBAM interrupts for Release 1.6 bitstreams	( SCGCQ00663206 ) 
 - Enable SAS1 interrupts( SCGCQ00663855 ) 
 - Enterprise: preparation for Enterprise interrupt and device interrupt support( SCGCQ00664180 ) 
 - Add Intruder Specific Define for Number of SGPIO Instances( SCGCQ00664340 ) 
 - MPI 2.6: additional AccessStatus values for PCIe Device Page 0( SCGCQ00664957 ) 
 - Ventura: Enable PBAM HeartBeat LED functionality	( SCGCQ00665975 ) 
 - Ventura: Map remaining cores as described in the original Ventura map up to POC10( SCGCQ00667112 ) 
 - Backend PCI: move device interrupt info structure( SCGCQ00668627 ) 
 - PL Sim additonal work( SCGCQ00668850 ) 
 - Enterprise: PDB MSI/MSI-x handler compatible with Enterprise	( SCGCQ00669530 ) 
 - Add check for Detroit PLB parity error by reading DCR regs( SCGCQ00669726 ) 
 - Ventura: SIO/LED control initialization	( SCGCQ00671021 ) 
 - Intruder: Firmware Dual context settings cleanup and setting dequeuing modes.( SCGCQ00674213 ) 
 - Ventura: SOP TM updates	( SCGCQ00675384 ) 
 - Intruder: Extend Manufacturing Pages support in master xsd file( SCGCQ00676261 ) 
 - Ventura: GPIO initialization	( SCGCQ00676410 ) 
 - Backend PCI: generate Set Slot Power Limit message( SCGCQ00676417 ) 
 - Review Intruder EDS v1.8 for CCR changes that apply to FW	( SCGCQ00680173 ) 
 - MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages	( SCGCQ00680527 ) 
 - Enterprise: tie legacy/MSIx interrupt handlers in with HW interrupts	( SCGCQ00680763 ) 
 - Ventura: Enterprise: DM PCIe Core start of day configuration	( SCGCQ00680765 ) 
 - Ventura: SPI library Callbacks need to be implemented for register read/writes.	( SCGCQ00681306 ) 
 - Ventura: Enterprise: update header file for new product definition	( SCGCQ00682820 ) 
 - PL: Remove plCompileOptions.h from the list of files needed for pli	( SCGCQ00682887 ) 
 - Support IOA Local RAM - IOP Changes	( SCGCQ00682893 ) 
 - Intruder FPGA Release 2.0 address map( SCGCQ00683085 ) 
 - Ventura: Enterprise: move backend lane dependent code in PCIe Device Manager	( SCGCQ00684295 ) 
 - PL: final cleanup of PL_INFO NumPhys and HwNumPhys( SCGCQ00685227 ) 
 - MPI 2.5: distribute Target Command Buffers Received across multiple reply queues	( SCGCQ00685820 ) 
 - Ventura: Enterprise: PCIe IO Unit Page 1 write handler( SCGCQ00686614 ) 
 - MPI 2.6: Extend Task Management - Target Reset Method to include PCIe devices( SCGCQ00686666 ) 
 - Ventura: merge SAS phy devhandle and PCIe phy devhandle usage( SCGCQ00686670 ) 
 - Intruder: modify PL build/release process to include IntruderFpga.xsd( SCGCQ00688174 ) 
 - Ventura: Provide more MMU table memory( SCGCQ00688248 ) 
 - Intruder & Ventura: Consolidate Reply Destination defines across various Cuda cores( SCGCQ00688686 ) 
 - Ventura: Enterprise: backend link speed/width control code( SCGCQ00690945 ) 
 - Dauntless: Add back in the copying of NVDATA for MR PL Builds( SCGCQ00692123 ) 
 - Ventura: Support to send MID’s in FxCore FxRequestor engines to Exception queue for TM trapping( SCGCQ00694241 ) 
 - Ventura: Support for HW CR to perform device handle check for PCIe device IO completions	( SCGCQ00694244 ) 
 - Ventura: Integrate PCIe Discovery with Port Enable handling( SCGCQ00694260 ) 
 - Update 'iop perfmon show' for multi core support	( SCGCQ00695443 ) 
 - Intruder: update 'iop show tlb'( SCGCQ00695530 ) 
 - Update chip linker directive file for how much memory is available( SCGCQ00695546 ) 
 - MPI 2.5: BIOS Page 1 additions( SCGCQ00700829 ) 
 - Ventura: Enable SCSI commands from uart( SCGCQ00702618 ) 
 - Updated master.xsd file with IntruderFpga.xsd changes( SCGCQ00703470 ) 
 - Ventura: Internal GIC and CCI support( SCGCQ00704455 ) 
 - Intruder: (IOP( SCGCQ00706279 ) 
 - Ventura: Update top level interrupt mapping to 1.2 version of EDS( SCGCQ00707300 ) 
 - Intruder: (IOP	( SCGCQ00707767 ) 
 - Ventura: Enable SAS Core Interrupts	( SCGCQ00709564 ) 
 - SAS3.5: Separate out SAS Phy Power Management so we can compile out the code if it is not working properly.( SCGCQ00709570 ) 
 - Intruder: prepare iopWorkArounds( SCGCQ00709601 ) 
 - Ventura: IT FW SPI Flash Boot - Remote FLASH	( SCGCQ00710132 ) 
 - Initial addition of Intruder specific build environment	( SCGCQ00710203 ) 
 - Ventura: Verify FIS Porting feature in the HW( SCGCQ00710210 ) 
 - Add QM Exception Queue Registers to PL Diagnostic Code( SCGCQ00710465 ) 
 - Provide interface to IOP to get local address to backend PCI address mapping.( SCGCQ00712817 ) 
 - Add Multi SAS Core support for Target Mode Hardware cleanup	( SCGCQ00712972 ) 
 - More multi core upgrades to Target Mode code	( SCGCQ00715204 ) 
 - Ventura: Add NVSRAM decode region to map for SPILIB testing	( SCGCQ00715637 ) 
 - Ventura: Make fast path selectable for SCSI Uart commands( SCGCQ00723335 ) 
 - PL: Implement section 7.7 of the NVMe specification( SCGCQ00723596 ) 
 - MPI 2.5: update copyright info( SCGCQ00728066 ) 
 - Ventura: Create NIC-400/DPE-400 Header File( SCGCQ00731690 ) 
 - Ventura: CSW Added Implement PLI Interrupt Handlers( SCGCQ00733171 ) 
 - Add IOP start queue for secondary processor( SCGCQ00734296 ) 
 - Intruder DDR3: Update register fields based on new MC spec( SCGCQ00734424 ) 
 - Ventura: Modify FPGA Build to support boot from SPI FLASH with XmemCopy( SCGCQ00734979 ) 
 - Ventura: If possible, eliminate the 4K guardband between the MMU table and the unmapped space( SCGCQ00735500 ) 
 - Ventura: Move Remote FLASH Application start to targeted OCM location( SCGCQ00736518 ) 
 - Ventura: reject backend PCIe devices that do not support MSI-x( SCGCQ00740574 ) 
 - Remove SAS_PL_ONLY macro	( SCGCQ00754441 ) 
 - Ventura: add CPU number to Reply Dest define	( SCGCQ00756765 ) 
 - Added the Interrupt map for Intruder A0	( SCGCQ00758572 ) 
 - Extend MFG Page 17 fields to accomodate more phys( SCGCQ00759493 ) 
 - Intruder: support for 84 GPIOs and 1 system heart beat LED using two GPIO modules( SCGCQ00759513 ) 
 - Ventura: Create GIC SGI code	( SCGCQ00759725 ) 
 - Ventura: Port synchronization macros from PPC to ARM	( SCGCQ00759731 ) 
 - Ventura: Implement cache Invalidate (and clean( SCGCQ00759733 ) 
 - Ventura: Create Official IT FPGA Build Release Scripts	( SCGCQ00762847 ) 
 - Ventura: Add SAS AI Slave register definitions( SCGCQ00764299 ) 
 - Intruder DDR3: For FPGA only, force High Temperature Refresh Settings to be used	( SCGCQ00765077 ) 
 - Dauntless: Build related changes	( SCGCQ00765117 ) 
 - Intruder: Route Non-Auto TxFM Interrupts to SAS Exception Queue	( SCGCQ00766711 ) 
 - Intruder: Allow Multiple SATA FIS Port IOs Outstanding( SCGCQ00768012 ) 
 - Ventura: Increment the number of IOP timers	( SCGCQ00768056 ) 
 - Remove fast path development test support( SCGCQ00769248 ) 
 - pl: Add some sanity checks for backend phy, port, SASCore mapping( SCGCQ00771332 ) 
 - Ventura: Simplify Versioning	( SCGCQ00771858 ) 
 - Intruder: Add support for RGMII phy used on Intruder Eval board( SCGCQ00774222 ) 
 - MPI 2.6: Add device off flag to SCSI Enclosure Processor messages( SCGCQ00776177 ) 
 - Ventura: Decrease FPGA RamLoad Boot Time	( SCGCQ00781011 ) 
 - Ventura: Add Contiguous Hint Capability for Code sections( SCGCQ00783007 ) 
 - MPI 2.5: add WWID to BIOS Page 3	( SCGCQ00785208 ) 
 - Ventura: MSS - Update HW header files to latest( SCGCQ00789522 ) 
 - MPI 2.6: New Phy event codes added to Ventura( SCGCQ00789600 ) 
 - Ventura: PCIe Discovery should yield to the IOP scheduler( SCGCQ00789678 ) 
 - Ventura: add FPGA build with backend PCIe code( SCGCQ00790217 ) 
 - MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable( SCGCQ00791885 ) 
 - modify output filenames used in a build batch file( SCGCQ00793209 ) 
 - Move Intruder NVDATA files to separate from other projects.( SCGCQ00793214 ) 
 - SAS3.5 cleanup project and remove all Invader out of Intruder/Dauntless( SCGCQ00793562 ) 
 - Ventura: Add ARM directives to assist in debug( SCGCQ00798838 ) 
 - Ventura: Enterprise: update Enterprise header files	( SCGCQ00799993 ) 
 - Ventura: Distribute PL Object Modules into PLI defined archives	( SCGCQ00801716 ) 
 - Ventura: Add the option to build smaller mini-release library binaries	( SCGCQ00803151 ) 
 - Ventura: backend PCIe: attempt some backend PCIe image size reduction	( SCGCQ00803550 ) 
 - Ventura: backend PCIe: configuration of host side mapping resources	(SCGCQ00805418 ) 
 - Ventura: Enterprise: add error tracker( SCGCQ00806134 ) 
 - Ventura: RMC handling of the various silicon resets	( SCGCQ00810262 ) 
 - Ventura: Enable multiple SAS core support( SCGCQ00811125 ) 
 - Backend PCIe: revisit FxCore requestor cleanup during TM	( SCGCQ00812748 ) 
 - Ventura: Port IOP Memory Requirements CLI Code	( SCGCQ00812990 ) 
 - Aladin Core Register Definition Updates	( SCGCQ00813022 ) 
 - MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough	( SCGCQ00813389 ) 
 - Ventura: Remove IO bit-bucketing code( SCGCQ00813416 ) 
 - Ventura: add RMC System timer( SCGCQ00813419 ) 
 - Remove Sas Port Virtualization(SPV( SCGCQ00813465 ) 
 - Ventura: RMC Interrupts( SCGCQ00813494 ) 
 - IOP: Update hardware to receive PCIe messages( SCGCQ00813957 ) 
 - Ventura: MSS - finish unfinished code	( SCGCQ00814452 ) 
 - Ventura: MSS - New registers from latest Memory Controller Hardware documentation( SCGCQ00814456 ) 
 - Ventura: MSS - DDR4 VREF training	( SCGCQ00814464 ) 
 - Ventura: MSS - read fifo (DFI_RL	( SCGCQ00814472 ) 
 - Update NVDATA_Bindings for Intruder	( SCGCQ00815576 ) 
 - Update pl utility functions to retrieve Hardware Context pointers to be remote core compatible( SCGCQ00816272 ) 
 - Intruder: Remove Ethernet and DDR support from normal IT firmware builds	( SCGCQ00816434 ) 
 - update FW Header to indicate MPI v2.6( SCGCQ00816899 ) 
 - SAS3.5FW: update to latest MPI v2.6 header files	( SCGCQ00817142 ) 
 - Ventura DA A/R: PCIE error Handling : Device side configurations	( SCGCQ00817999 ) 
 - Ventura: backend PCIe: some bringup changes	( SCGCQ00818337 ) 
 - Handling errors from pliPortEnable( SCGCQ00818760 ) 
 - Cleanup of INTRUDER_PORTING	( SCGCQ00819220 ) 
 - Tiger: Add PL FW support to account for External SED SAS Cores during MaxSasCorenum considerations( SCGCQ00819898 ) 
 - Ventura: Eliminate references to capabilities structures in DM and PCI core (hardware( SCGCQ00820930 ) 
 - Ventura: Port SysDMA PCIE Messaging Capabilities to new hardware	( SCGCQ00820943 ) 
 - Ventura: Create Maverick.h header that compiles	( SCGCQ00820945 ) 
 - Ventura: PIM/POM setup Porting( SCGCQ00820946 ) 
 - Ventura: backend PCIe: some bringup changes( SCGCQ00821615 ) 
 - Ventura DA A/R: TM Code changes related to PCIe error handling.( SCGCQ00821974 ) 
 - Ventura DA A/R: FxCore Interrupt/exception handling related to PCIe errors.	( SCGCQ00821979 ) 
 - Implement PCIe error recovery by handling AER interrupt generated by root port for direct attached PCIe devices.( SCGCQ00821994 ) 
 - Ventura: Update CCR header file and code to latest EDS revision	( SCGCQ00822252 ) 
 - Ventura: Port misc low-level PCI CLI debug functions	( SCGCQ00822556 ) 
 - pl: backend PCIe: modify TM device status check timers as in device init	( SCGCQ00823052 ) 
 - Ventura Tiger: add enumeration support for Tiger and Tiger emulator	( SCGCQ00823434 ) 
 - AAPL 2.0.0 Integration with the ComboSerdes Library	( SCGCQ00824299 ) 
 - Updated maverick.h to EDS 2.0.8	( SCGCQ00824524 ) 
 - Ventura: Enterprise: PIM/POM mapping bringup	( SCGCQ00824588 ) 
 - Send periodic NOTIFY(SPINUP	( SCGCQ00824941 ) 
 - Update the Serdes AAPL to 2.1.0	( SCGCQ00825070 ) 
 - Ventura: Use consistent method for printing DevHandle and Mid( SCGCQ00825825 ) 
 - MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura( SCGCQ00827088 ) 
 - Implement Comboserdes Library Functions for Hardware Initialization( SCGCQ00827427 ) 
 - Ventura SW A/R: Handle SHEX Stall on application errors	( SCGCQ00827432 ) 
 - Ventura: MSS - APIs or functionality from Invader or Intruder that has not been included in Ventura( SCGCQ00827507 ) 
 - RMC support for cache offload( SCGCQ00828214 ) 
 - MPI 2.6: add PCI Device ID's	( SCGCQ00828497 ) 
 - Ventura: backend PCIe: some bringup changes( SCGCQ00829039 ) 
 - Ventura DA A/R: Define PCIe error related status codes and log info codes( SCGCQ00829228 ) 
 - Update Ventura interrupt handlers( SCGCQ00829571 ) 
 - Ventura - PLI naming tweaks for PIM/POM (part 2( SCGCQ00830094 ) 
 - Ventura: Consolidate setting of TOPNIC( SCGCQ00830711 ) 
 - Ventura Tiger- Update SOD memory calculation for SASCore Completion Queues to account for remote SAScores( SCGCQ00830799 ) 
 - Set Number of VFs and Number of Host Credits in MFG Page 9( SCGCQ00831053 ) 
 - MPI 2.6: methods to report Active Cable power problems( SCGCQ00831588 ) 
 - SAS3324 Eval Card Partial NVDATA Plus Cable Management Enabled Version( SCGCQ00831674 ) 
 - Virtual SES SGPIO Support( SCGCQ00832629 ) 
 - Marlin: backend PCIe: support additional link configurations	( SCGCQ00832638 ) 
 - Marlin: x144 DDR Support	( SCGCQ00832642 ) 
 - Update Intruder feature identification bits( SCGCQ00832700 ) 
 - IOP: Add Intruder A0 to the list of supported devices( SCGCQ00832713 ) 
 - IOP BL (Ventura( SCGCQ00832991 ) 
 - Integrate PCIe link events with PCIe Discovery and Device Manager( SCGCQ00833319 ) 
 - Ventura: backend PCIe: some bringup changes( SCGCQ00833580 ) 
 - Ventura: backend PCIe: PLI address pool tweak( SCGCQ00833813 ) 
 - SAS9305-16e Partial NVDATA Plus Cable Management Enabled Version	( SCGCQ00834180 ) 
 - SAS9305-24i Partial NVDATA Plus Manufacturing Page 13 Settings( SCGCQ00834181 ) 
 - IOP: Configure Intruder SAS cores register locations	( SCGCQ00834206 ) 
 - Ventura: Support Raptor R10 and R31	( SCGCQ00834846 ) 
 - PL: Check in the latest serdes settings for Intruder A0 silicon	( SCGCQ00835410 ) 
 - BL: Remove SBR loaded check in initialization code( SCGCQ00835438 ) 
 - Bootloader: Re-enable SBR initialization check( SCGCQ00835455 ) 
 - Guinness CSW Library updates after integration with SAS35X48	( SCGCQ00836774 ) 
 - Ventura: backend PCIe: reporting of device link capabilities in PCIe Device Page 0( SCGCQ00836800 ) 
 - IOP: Fully support additional I2C cores( SCGCQ00836903 ) 
 - RMC: Cache offload support for OCM flush, pausing offload, error handling( SCGCQ00837742 ) 
 - Intruder A0: Multiple NVDATA Changes	( SCGCQ00838057 ) 
 - Ventura: backend PCIe: resolve some NVMe TM TODOs( SCGCQ00839540 ) 
 - Ventura: Increase FPGA "FakeRAM" size to 4MB	( SCGCQ00839552 ) 
 - Ventura Tiger: Setup remote cores on Ventura IOA	( SCGCQ00841008 ) 
 - Ventura: Update FPE Ring Buffer Indices to Impala 2.2.9	( SCGCQ00841735 ) 
 - Ventura Tiger: Poll for Remote SASCore Interrupt	( SCGCQ00843664 ) 
 - Release notes not needed. plSim is not released during a "standard" release.	( SCGCQ00843993 ) 
 - Ventura: PL to provide capability for MR FW to change the IO completion (ReplyDestination	( SCGCQ00846550 ) 
 - Ventura: SGPIO Double Pump Mode support	( SCGCQ00846941 ) 
 - Ventura: Remove Dauntless PCIe discovery implementation	( SCGCQ00848347 ) 
 - Turn on temperature monitoring for Cutlass Channel boards( SCGCQ00850747 ) 
 - Ventura: add some additional register dumping debug code	( SCGCQ00852294 ) 
 - Ventura: additional items for diag console debug dump commands( SCGCQ00852648 ) 
 - MPI 2.6: SRIOV support for PCIe devices( SCGCQ00852827 ) 
 - MPI 2.6: Update Flash Signature.	( SCGCQ00852831 ) 
 - MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1( SCGCQ00853162 ) 
 - Ventura: Add APB SAS Slave registers to gSASCore memory map( SCGCQ00853334 ) 
 - Add support for GPIO Drive Activity LED (Wide Port Activity( SCGCQ00853683 ) 
 - ComboSerdes Wrapper EDS 2.3 Updates	( SCGCQ00854332 ) 
 - Ventura: Update interrupt table to EDS version 2.2.5	( SCGCQ00855344 ) 
 - Ventura: Modify Ventura code such that features that used to use config trapping use config writing mechanism( SCGCQ00855704 ) 
 - Ventura: Modify clock frequency dividers for bitstream 3.0 compatibility	( SCGCQ00856495 ) 
 - Ventura: Add the APB slave registers to the debug dump( SCGCQ00857054 ) 
 - Need spurious interrupt checks.( SCGCQ00860268 ) 
 - IOP: Eliminate reference to FW downgrade active bit from CFGI code( SCGCQ00861856 ) 
 - Ventura: Add support for PCIe devices using DDR in IT( SCGCQ00862509 ) 
 - Ventura: FPGA: 3.2 bitstreams changes( SCGCQ00865103 ) 
 - Ventura: backend PCIe: enable maximum PCIe device count in FPGA DDR build( SCGCQ00865951 ) 
 - Ventura: Use Host initiated IO Fast path flag bit to determine Frame Ownership( SCGCQ00866323 ) 
 - Handle PCIe MemRd, MemWr failures issued over Enterprise POB in Axi2Shell Bridge interrupt handler( SCGCQ00866777 ) 
 - VENTURA: Update SPI registers Vayu EDS 2.2.15( SCGCQ00867427 ) 
 - Intruder SR-IOV: Update NVData for optimal resource allocation( SCGCQ00867906 ) 
 - Intruder IOP: Compile out unnecessary SGL types from SysDMA( SCGCQ00870980 ) 
 - Enable DCR Macro in iopInitFastPathAccess( SCGCQ00871716 ) 
 - Enabled Avago SerDes debug functions	( SCGCQ00872114 ) 
 - Add SBR header information( SCGCQ00872116 ) 
 - Ventura: Update PortFacts reply for Port Type( SCGCQ00872264 ) 
 - Ventura: Update firmware signature per latest EDS( SCGCQ00872787 ) 
 - Ventura: backend PCIe: tweaks to TM and interlocks with other subsystems	( SCGCQ00874057 ) 
 - NVData: Create Intruder A1( SCGCQ00877621 ) 
 - IOP: Support Intruder A1	( SCGCQ00878608 ) 
 - IOP: Removed old code which is no longer used( SCGCQ00879395 ) 
 - Additions for Tiger/Styker build	( SCGCQ00880830 ) 
 - IOP: Configure additional compile options for Tiger support( SCGCQ00881793 ) 
 - Sync tigerbase.h up with ventbase.h	( SCGCQ00881832 ) 
 - TigerStryker: Add tigerfpga build and options to turn off PDB and turn on PSB support.( SCGCQ00881838 ) 
 - Ventura: backend PCIe: clean up some TODOs	( SCGCQ00881882 ) 
 - TigerStryker: Add new defines for PSB and PDB builds Part 2	( SCGCQ00883029 ) 
 - Ventura: backend PCIe: hard reset the PDB cores at PL init time	( SCGCQ00883464 ) 
 - Implement MPI 2.6 Active Cable Exception Event( SCGCQ00883606 ) 
 - MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit	( SCGCQ00884740 ) 
 - BL: First pass of adding conditional compilation for MMU and MPU	( SCGCQ00885620 ) 
 - Update the DDR training burst mechanism.	( SCGCQ00886632 ) 
 - Ventura: control which NVMe SGL format to use.( SCGCQ00886974 ) 
 - Enable SIO/I2C Bus muxing based on the backplane sideband signals( SCGCQ00888047 ) 
 - Tiger: IOA Init( SCGCQ00888287 ) 
 - Tiger/Stryker: Separate PDB code into new define - part I( SCGCQ00888868 ) 
 - Ventura MSS: Ability to change MPR pattern used in training algorithms.( SCGCQ00888903 ) 
 - Ventura: Add IOA debug prints to some releases( SCGCQ00890390 ) 
 - Tiger/Stryker: Isolate PDB code from Tiger/Stryker builds Part II( SCGCQ00891905 ) 
 - Ventura - DDR Frequency Scaling - IOP Support( SCGCQ00892969 ) 
 - Ventuar - DDR Frequency scaling - During Initalization and run time.	( SCGCQ00892975 ) 
 - Ventura - DDR Frequency Scaling - Work on TODO items	( SCGCQ00892977 ) 
 - BL: Updates for Tiger to copy the firmware to the correct location( SCGCQ00895156 ) 
 - Ventura: backend PCIe: improve robustness of the INTx handler( SCGCQ00896564 ) 
 - Bootloader: Tiger/Stryker initial round of changes to get firmware booted on FPGA( SCGCQ00897171 ) 
 - Tiger IOP: Add support for the PBAM GPT hardware block( SCGCQ00898142 ) 
 - IOP: Update UART initialization code	( SCGCQ00900631 ) 
 - BL: Tiger: Allow firmware to run from a ram loaded location( SCGCQ00904576 ) 
 - Ventura: Additional MSIX combined mode changes( SCGCQ00905622 ) 
 - Remove Dauntless Defines: Makefiles and build scripts.( SCGCQ00905980 ) 
 - Remove Dauntless Defines: IOP code( SCGCQ00905981 ) 
 - Remove Dauntless Defines From MSS/DDR library( SCGCQ00905996 ) 
 - Remove support for Dauntless from hardware header files	( SCGCQ00905997 ) 
 - Removing DAUNTLESS specific functionality from SPI library( SCGCQ00906001 ) 
 - Remove Dauntless Defines: Remove Dauntless specific configuration from NVDATA files.	( SCGCQ00906003 ) 
 - Remove Dauntless Defines: Utilities	( SCGCQ00906005 ) 
 - IOP: Update register block for Tiger/Stryker	( SCGCQ00907735 ) 
 - IOP: Tiger: Move the firmware executable to run from 1K from the beginning of memory	( SCGCQ00908709 ) 
 - Allow Unique SAS address for Direct Attached Sata Devices( SCGCQ00908795 ) 
 - BL: Configure Tiger bootloader to copy firmware correctly( SCGCQ00910285 ) 
 - Tiger/Stryker: CSR Handler (Cfg Read and Writes( SCGCQ00910623 ) 
 - Ventura: Make Some Fault Codes Unique	( SCGCQ00910652 ) 
 - Ventura: Update coherent memory settings based upon default SBR settings	( SCGCQ00910690 ) 
 - Ventura: Provide an FPGA work-around to initialize the Expansion ROM Window ASAP	( SCGCQ00910692 ) 
 - IOP: Remove reference to MR Key	( SCGCQ00910882 ) 
 - Ventura: backend PCIe: remove stale early FPGA hacks	( SCGCQ00911513 ) 
 - IOP: Conditionally compile IOA RAM support( SCGCQ00912286 ) 
 - IOP: Add abstraction to PCI device ID code( SCGCQ00913490 ) 
 - IOP: Add GPT timer initialization routine( SCGCQ00915228 ) 
 - MPI 2.6: Update Ventura family device ids to match latest EDS( SCGCQ00915256 ) 
 - MPI 2.6: update Marlin-class device IDs( SCGCQ00915336 ) 
 - Ventura : MSS : DDR4 LRDIMM support : Configure LRDIMM specific MC registers	( SCGCQ00916707 ) 
 - Add support to check Chip reset enabled bit before deciding to perform actual offload( SCGCQ00917637 ) 
 - Initialize the Spico Interrupt Sequences and add an API to allow per-phy SAS/SATA TX EQ settings	( SCGCQ00917655 ) 
 - Ventura Build: Add a minimized build to the list of targets	( SCGCQ00917696 ) 
 - Update AAPL code to 2.2.3( SCGCQ00918244 ) 
 - Tiger/Stryker: MCPU Enumeration and Configuration of PEX ports and attached devices.	( SCGCQ00918258 ) 
 - Ventura: RMC misc changes to interrupts	( SCGCQ00918452 ) 
 - IOP: Update GPIO code for Tiger/Stryker	( SCGCQ00918494 ) 
 - Ventura: Map WidePort activity group to GPIO pins( SCGCQ00919252 ) 
 - Ventura: Add support for GPIO drive control and slew rate( SCGCQ00919263 ) 
 - IOP: Disable TPH errata workaround in Tiger and Stryker( SCGCQ00919279 ) 
 - Ventura: Remove SAS core SGPIO module support code	( SCGCQ00919473 ) 
 - Ventura A0: Add support for B0 HW CR46 - PBAM InFrame activity mapping logic changes for PDB and SAS cores( SCGCQ00919497 ) 
 - IOP: Remove unnecessary workaround code	( SCGCQ00921754 ) 
 - MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks( SCGCQ00922213 ) 
 - Ventura: Remove VENTURA_PORTING from Makefiles and headers( SCGCQ00922883 ) 
 - Need C99 and CPP versions of the library for Ventura	( SCGCQ00922914 ) 
 - Download Guinness Serdes Spico firmware using the Sbus broadcast address	( SCGCQ00923584 ) 
 - Ventura: RMC update reset sequence( SCGCQ00923609 ) 
 - IOP: Add VIC Hardware files	( SCGCQ00924375 ) 
 - Update Ventura PL code for MPI/SED device enumeration( SCGCQ00924378 ) 
 - Ventura: Prepare For ARM DS-5 5.22 Update( SCGCQ00924431 ) 
 - NVMe SCSI Translation updates( SCGCQ00925607 ) 
 - PL: Ventura-Tiger: SED/Tiger Completion Q allocation	( SCGCQ00925758 ) 
 - Remove debug symbols from Ventura C99 library( SCGCQ00925770 ) 
 - MPI 2.6: Remove all SOP references( SCGCQ00925839 ) 
 - Ventura: backend PCIe: allow usage of 64 bit space for device BARs( SCGCQ00926634 ) 
 - IOP/PL: Use 128 byte reply message size	( SCGCQ00927749 ) 
 - IOP/PL: Update additional structures to use OCM PLB Segment 2( SCGCQ00927962 ) 
 - Ventura: Ensure uniqueness of PCI Bus Numbers for devices in the backend PCIe topology( SCGCQ00927968 ) 
 - IOP: Tiger remove support for CCI400 hardware( SCGCQ00928547 ) 
 - Ventura: Update Inquiry results for NVMe drives to be compliant with version 1.5 of the NVMe SCSI Translation Reference	( SCGCQ00928876 ) 
 - IOP: Tiger: Enable multi-host IOC mode( SCGCQ00928904 ) 
 - Implement Ventura A0 workarounds per HW team request.( SCGCQ00929743 ) 
 - Tiger/Stryker: Fix hard coded values in PSB's IOP SysDMA interface function( SCGCQ00932427 ) 
 - Tiger: Remove PCI_PSB from build and use IOP/PL defines( SCGCQ00932472 ) 
 - Ventura: backend PCIe: optimize firmware start path for encapsulated requests( SCGCQ00932934 ) 
 - Ventura: Create Silicon Build Scripts( SCGCQ00932981 ) 
 - Support the updated A0 pre-silicon Interrupt Sequences Spreadsheet( SCGCQ00932997 ) 
 - MSS library: Add 40-bit DDR support in SPD( SCGCQ00934415 ) 
 - Active cable Power management support for Intruder/Cutlass( SCGCQ00935460 ) 
 - Ventura: backend PCIe: handle max payload size mismatch	( SCGCQ00936258 ) 
 - Enable A0 Hardware Initialization( SCGCQ00936652 ) 
 - Ventura: backend PCIe: handle some additional FxCore exception mid type cases( SCGCQ00937444 ) 
 - PL: Remove old remote SED Driver code from PL( SCGCQ00937808 ) 
 - Venutra: Update SOC SBR settings to latest values( SCGCQ00937914 ) 
 - Remove leftover Dauntless code from SAS 3.5 firmware codebase( SCGCQ00938267 ) 
 - Ventura/Marlin: backend PCIe: resolve some TODOs	( SCGCQ00938516 ) 
 - Ventura: backend PCIe: add runtime control of PDB hardware workarounds( SCGCQ00938856 ) 
 - Implement Sbus Reset	( SCGCQ00938921 ) 
 - Tiger: MPT end point initialization and CSR FIFO Start of Day Setup( SCGCQ00940281 ) 
 - Removed internal CSW library functions that used run time library print formatting functions( SCGCQ00940315 ) 
 - Tiger: FPGA specific quirks and workarounds	( SCGCQ00941057 ) 
 - Remove receiver training, Enable receiver termination, Change TX Amplitude( SCGCQ00941130 ) 
 - PL: Ventura: Add processing of PCIe Topo Change List Add from downstream MPI devices	( SCGCQ00942302 ) 
 - Tiger: Add Version files for Tiger Firmware( SCGCQ00943012 ) 
 - Ventura: make CSW library build part of project build( SCGCQ00943199 ) 
 - Tiger: Added Release build job script( SCGCQ00944615 ) 
 - IOP: Implement the macros for enabling/disabling config space for Tiger( SCGCQ00944747 ) 
 - Tiger: Clear Inbound Msix Interrupt Mask	( SCGCQ00944844 ) 
 - Update Spico interrupt sequences and spico firmware( SCGCQ00944860 ) 
 - VENTURA: GPIO register update( SCGCQ00945612 ) 
 - Tiger: get PCI_DEVICE=0 build working( SCGCQ00945790 ) 
 - IOP: Add fault interrupt support	( SCGCQ00945948 ) 
 - IOP: Tiger: Get gIopBootParams.RtFeatures populated correctly( SCGCQ00945968 ) 
 - Ventura: backend PCIe: configure some link speed related settings in the DM Core	( SCGCQ00947271 ) 
 - MPI 2.6: Remove all AHCI references( SCGCQ00948258 ) 
 - Ventura: Update PCE SBR binary( SCGCQ00948439 ) 
 - Ventura: Revert to old method for FPE frame ownership change	( SCGCQ00948489 ) 
 - Ventura: Enable Support for Second UART	( SCGCQ00948864 ) 
 - MPI 2.6: Add support for SAS-4 and PCIe-4( SCGCQ00948955 ) 
 - Ventura: RMC A0 bring up changes	( SCGCQ00949117 ) 
 - MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0( SCGCQ00949638 ) 
 - Tiger: add Tiger unique NVDATA( SCGCQ00949784 ) 
 - Tiger: Add support for FIQ Event FIFO in Tiger( SCGCQ00949801 ) 
 - Ventura: backend PCIe: A0 bringup changes( SCGCQ00950032 ) 
 - BL: Tiger: Enable memory protection unit	( SCGCQ00950064 ) 
 - IOP: Fix general purpose timer prescalers for FPGA( SCGCQ00950194 ) 
 - Ventura: Add vtboot.rom to MegaRAID release package( SCGCQ00950517 ) 
 - Ventura: Update release scripts for current NVDATA file names and location( SCGCQ00950683 ) 
 - Ventura: Add Harpoon SBR to build process( SCGCQ00951155 ) 
 - Fix initial checks for feature registers on Crusader( SCGCQ00951163 ) 
 - Ventura: Add backtrace et al to ring buffer dump	( SCGCQ00951940 ) 
 - Ventura: Add all ASC/ASCQ's to scsi.h( SCGCQ00952486 ) 
 - Ventura: backend PCIe: NVMe submission queue timeout handling modification( SCGCQ00952601 ) 
 - Ventura: backend PCIe: configure PERST# GPIOs( SCGCQ00953712 ) 
 - Ventura: Add CSW register dump to cli( SCGCQ00953834 ) 
 - MPI 2.6: add LinkNum field to the PCIe Link configuration pages( SCGCQ00954619 ) 
 - Tiger: Implement workaround for spurious FxCore exception interrupt	( SCGCQ00954832 ) 
 - Create SBR and ROM images for Ventura ROC chip variant.( SCGCQ00958165 ) 
 - Ventura: Check SBR Load Status( SCGCQ00958167 ) 
 - Tiger: Handle POM errors	( SCGCQ00964901 ) 
 - Tiger: Implement DPC support	( SCGCQ00965091 ) 
 - Ventura: Add code to prevent PDB access if PDB PLL not locked( SCGCQ00966067 ) 
 - Ventura: Enable PIM2 (Expansion ROM	( SCGCQ00966590 ) 
 - Ventura: Add text to boot loader to verbosely explain PCE DeviceID Failures	( SCGCQ00968487 ) 
 - Ventura: backend PCIe: decrease verbosity of IEEE SGL to PRP translation debug prints( SCGCQ00968712 ) 
 - Ventura: Need support for both uniform and non-uniform Spansion parts( SCGCQ00970821 ) 
 - IOP Logic for updating the NVDATA Flags to indicate Current Active Cable Power Exception.( SCGCQ00981722 ) 
 - Add support for TomCat variant of Ventura chip.	( SCGCQ00982536 ) 
 - Modify Ventura makefile to suppress license expiration warning( SCGCQ00983360 ) 
 - Tiger: integrate using combo serdes wrapper library for SERDES init( SCGCQ00987114 ) 
 - Tiger: Add performance monitor support.( SCGCQ00987214 ) 
 - Ventura: Add CLI command to dump CCI-400 registers( SCGCQ00987455 ) 
 - Update Spico Firmware and remove the Tx Phase Slip workaround( SCGCQ00987750 ) 
 - Ventura: Firmware Download taking longer than necessary( SCGCQ00988341 ) 
 - MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply	( SCGCQ00988360 ) 
 - Ventura: Verify that the alternate location for POM works during host boot( SCGCQ00988608 ) 
 - Tiger: Multiple host support for CSR	( SCGCQ00988657 ) 
 - Ventura: Port IO Unit Page 7 PCIe Link Speed & Width to Ventura( SCGCQ00991747 ) 
 - Tiger: Initial Veloce updates for Firmware( SCGCQ00991777 ) 
 - Ventura: Set SBR Link Control 2 Register to Gen2	( SCGCQ00993135 ) 
 - IOP: Map pcie core interrupts to appropriate handlers( SCGCQ00993753 ) 
 - Set TxAMP for SAS/SATA and PCIe in the CSW Interrupt sequences( SCGCQ00995431 ) 
 - MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout"	( SCGCQ00996127 ) 
 - Ventura A0: Add External Interrupt support for GPIO Bank B	( SCGCQ00997300 ) 
 - Ventura: Support for user configurable option to select the PBAM GPIO LED Data polarity( SCGCQ00997306 ) 
 - PL: Improve MPI IRQ handling and add SCSI IO support	( SCGCQ00999444 ) 
 - Ventura: Configure the PLLs on SBus ring	( SCGCQ00999504 ) 
 - Tiger: Rename iopCcrRegRead/Write( SCGCQ01000151 ) 
 - IOP: Improve usefulness of SCSI IO error trace print and accuracy of SCSI IO Error Reply	( SCGCQ01000640 ) 
 - Support for PCIe Dynamic Power Allocation in Ventura	( SCGCQ01001494 ) 
 - Tiger: Handle DMA failures during host port link down.( SCGCQ01002313 ) 
 - MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply	( SCGCQ01002367 ) 
 - Ventura: Add host side spico revision to version output( SCGCQ01002441 ) 
 - Ventura: change RMC to use default values for PCE Hot Reset( SCGCQ01003264 ) 
 - IOP: Tiger: Add software emulated PCI configuration space registers( SCGCQ01003352 ) 
 - IOP: Implement Device Serial Number extended PCI capability( SCGCQ01003374 ) 
 - Ventura: Increase FIFO RAM max to 4096 entries( SCGCQ01004149 ) 
 - Ventura: Update XML Files to support automated SBR modification( SCGCQ01004323 ) 
 - Ventura: Create partial XML for 9400-16i (Bristol( SCGCQ01005098 ) 
 - Ventura: Port Capability to scan NVDATA for CHIPID when PCIID fails( SCGCQ01009099 ) 
 - MPI-2.6: backend PCIe feature initialization status reporting( SCGCQ01009104 ) 
 - PL: Use message frames as reply frames for MPI driver( SCGCQ01010464 ) 
 - Tiger Ventura: Store secondary SED MPT endpoint in upper half of MPI device array and populate FPE device state table for remote drives( SCGCQ01010549 ) 
 - Tiger: Intial setup of Messaging Unit Hardware to operate in Tiger mode( SCGCQ01011139 ) 
 - VENTURA: Update SPI library so it puts the SPI FLASH in the fastest mode available( SCGCQ01012095 ) 
 - Tiger: Add SED Init message( SCGCQ01012121 ) 
 - Ventura: Add initial support for Marlin, Mercator and Marut( SCGCQ01012455) 
 - Tiger FPGA: set CCR mode to Tiger mode instead of Styker	( SCGCQ01012471 ) 
 - MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request( SCGCQ01013930 ) 
 - IOP: Tiger must use MSIx 1 for sending events( SCGCQ01014837 ) 
 - Ventura PL: Provide SED with DDR information from IOC( SCGCQ01015368 ) 
 - Tiger: Send FirstDevhandle in SED init message( SCGCQ01015370 ) 
 - MPI2.6: Fix defines that are not unique within the first 32 characters( SCGCQ01015826 ) 
 - MPI 2.6: direct reporting of negotiated PCIe link width and speed( SCGCQ01017027 ) 
 - MPI 2.6: Backend SRIS mode enable flag( SCGCQ01018687 ) 
 - Tiger Ventura - if Tiger or Ventura fault, ensure the other side is faulted as well.	( SCGCQ01019232 ) 
 - Ventura/Marlin: backend PCIe: Link number field in PCIe Link Page 3	( SCGCQ01019238 ) 
 - Ventura PL: Organize MPI SED initialization routines into their own file	( SCGCQ01020470 ) 
 - MPI2.6: Reserve ExtPageTypes for Dragon	( SCGCQ01020473 ) 
 - Tiger BL: Modify bootloader scatter file to use base address macro( SCGCQ01020741 ) 
 - Ventura: Enable Active cable Management support( SCGCQ01021229 ) 
 - Ventura: Add support to detect BAR sizes for PL Reservations	( SCGCQ01021598 ) 
 - Tiger PL SED: Initial Handling of Task Managements to an SED attached end device	( SCGCQ01023127 ) 
 - Ventura MSS: Collection of changes for A0 bring up( SCGCQ01023729 ) 
 - IOP: Add additional PCIe Page support to iop show cfg( SCGCQ01023855 ) 
 - Update Spico firmware to version 0x085e and utilize the new DFE reset mechanism( SCGCQ01024059 ) 
 - Aero: initial makefile changes( SCGCQ01024834 ) 
 - Tiger IOP: Various hacks to get the second path to work	( SCGCQ01025622 ) 
 - Ventura A0: Update IOC Page 8 to enable Enclosure Slot mapping( SCGCQ01027212 ) 
 - FPGA: full ring buffer is dumped to UART on FPGA builds( SCGCQ01027917 ) 
 - VENTURA: SPI library quad mode nvsram( SCGCQ01027928 ) 
 - Ventura PL: Configure MPI SED Driver to use different sized queues( SCGCQ01028106 ) 
 - Added offset to Trace Buffer Print( SCGCQ01028857 ) 
 - Spico firmware 005F and Receiver Calibration fixes( SCGCQ01028936 ) 
 - Tiger BL: Enable instruction cache in the R4	( SCGCQ01029656 ) 
 - Ventura Tiger: Report Tiger attached SATA devices as SATA devices in Ventura.( SCGCQ01031015 ) 
 - Ventura IOP+PL: Add support for MPI Passthrough request and reply( SCGCQ01032692 ) 
 - IOP: Remove usages of PL_FEATURE_PCI_DEVICE_SUPPORT from IOP	( SCGCQ01032806 ) 
 - Ventura: changed PCIe Hot reset handling	( SCGCQ01034959 ) 
 - PL: Add configuration page handling for SED attached PCIe devices( SCGCQ01035127 ) 
 - Tiger FPGA: Fault if IOC Init request received on non zero IOC( SCGCQ01035215 ) 
 - Ventura PL: Convert Expander and Switch DevHandles in Topology Change List Events( SCGCQ01035243 ) 
 - IOP: Disable SED support compile option in Ventura by default( SCGCQ01036856 ) 
 - NVData: Update Tiger NVData to reduce the number of DevHandles allocated	( SCGCQ01037219 ) 
 - Add SRIS support	( SCGCQ01043121 ) 
 - IOP: Change location of FlashLayout in IOP_MEM_PARAMS( SCGCQ01043978 ) 
 - Ventura Corrective Actions for Board Over Temperature Conditions	( SCGCQ01044068 ) 
 - Update ComboSerdes library to Spico firmware 0E5F( SCGCQ01045799 ) 
 - Ventura: Dover NVDATA for 8e (9400-8e( SCGCQ01048676 ) 
 - PL: Configure PCIe switch BARs( SCGCQ01049391 ) 
 - CSW: Modify exit bypass sequence to fix PCI detectio	( SCGCQ01050553 ) 
 - Ventura: SPI Library - support Micron flash MT25QU128 1.8V 64 KB sector( SCGCQ01052708 ) 
 - Ventura: RMC enhanced interrupt handling for adapter reset	( SCGCQ01053436 ) 
 - PL: Add support for memory translation in SAS Core( SCGCQ01058395 ) 
 - Tiger IOP: Add code to translate SGLs targeting the SED hosts' internal memory( SCGCQ01059930 ) 
 - Ventura MSS: Improve write performance with ECC enabled( SCGCQ01060884 ) 
 - ComboSerdes: Removed unimplemented routines	( SCGCQ01062229 ) 
 - Load SerDes Spico processors in parallel	( SCGCQ01062231 ) 
 - Tiger: Cleanup code in iopGPIO.c	( SCGCQ01062237 ) 
 - Ventura: Add device side SPICO FW version to pliShowVersion(	( SCGCQ01062566 ) 
 - MPI2.6: Add x16 PCI support for Marlin family products( SCGCQ01063009 ) 
 - Ventura MSS: Method to artificially delay clock when the clock trace is not sufficiently longer than the strobe trace( SCGCQ01063021 ) 
 - Ventura: Create PLI compliant method for PL to check debug print mask( SCGCQ01063057 ) 
 - Integrate MPI2.6 headers 2.00.44	( SCGCQ01063292 ) 
 - Tiger: Get Tiger to compile with PL_FEATURE_CSW_LIB enabled	( SCGCQ01063627 ) 
 - ComboSerdes: Support a number of Sbus Rings that is different from the number of CSW blocks( SCGCQ01065677 ) 
 - Tiger: removed unused code in IOP_FEATURE_SED_SUPPORT_DEVTEST_TEMP( SCGCQ01065701 ) 
 - PL: Support Translation of Additional Log Pages( SCGCQ01067698 ) 
 - Ventura IOP : Support Dual Rank DDR4	( SCGCQ01068988 ) 
 - ComboSerdes: SAS/SATA TXEQ Settings Adjusted	( SCGCQ01071317 ) 
 - ComboSerdes: Untrained Receiver DFE Settings Updated	( SCGCQ01071320 ) 
 - Ventura: Delete AHCI code from codebase	( SCGCQ01071349 ) 
 - MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page( SCGCQ01071374 ) 
 - Ventura: Update coherency settings to match hardware team's settings	( SCGCQ01073946 ) 
 - Tiger A0: PCIe Link Configuration Setup	( SCGCQ01076376 ) 
 - Tiger IOP: Allow writes to PCI Express Device Status and Control register to update hardware	( SCGCQ01076761 ) 
 - Makefile cleanup for SCSI over PCIe (SOP	( SCGCQ01080155 ) 
 - Aero: more build changes	( SCGCQ01080681 ) 
 - Add debug information to ring buffer when PLLs fail to lock	( SCGCQ01083258 ) 
 - Ventura: backend PCIe: enable PDB PLL SSC( SCGCQ01083690 ) 
 - Ventura: Move GPIO LED Data Mux source selection configuration from IOP to PL	( SCGCQ01083822 ) 
 - ComboSerdes: Updated 3/6/12 G SAS Optical TX Equalization	( SCGCQ01084938 ) 
 - MPI 2.5: Add new connector types	( SCGCQ01085073 ) 
 - Marlin: Update CCR header file to the latest spec( SCGCQ01086086 ) 
 - Tiger: Implement A PCIe Backend Function to Check if the Root Complex is Enabled	( SCGCQ01087447 ) 
 - ComboSerdes: Guinness CSW B0 Support	( SCGCQ01087482 ) 
 - Ventura: RMC AVSO changes	( SCGCQ01091723 ) 
 - Ventura: backend PCIe: enable/disable new FxCore features at runtime	( SCGCQ01092303 ) 
 - MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout"( SCGCQ01092340 ) 
 - Update Spico firmware on host side to 0x1060.( SCGCQ01092343 ) 
 - Ventura: Add capability to handle interrupts during firmware download( SCGCQ01092407 ) 
 - Ventura: Modify MCTP to SysDMA interface for discovery so that the data comes out with the correctly	( SCGCQ01092412 ) 
 - Aero: modifications to compiler optimizations( SCGCQ01092420 ) 
 - ComboSerdesLib Update default ARM tools to DS-5 Version 5.24	( SCGCQ01093491 ) 
 - ComboSerdes: Enable SASCLK for all phys on Tiger	( SCGCQ01095102 ) 
 - Aero: Update miniDMA library for new compiler( SCGCQ01095725 ) 
 - Modify IT Boot loader to support MegaRaid Flash Regions	( SCGCQ01099725 ) 
 - Ventura MSS: Change Marlin compile option to run time option	( SCGCQ01099799 ) 
 - Ventura: fix comment in assembly file( SCGCQ01099871 ) 
 - Remove IR source code( SCGCQ01107754 ) 
 - Ventura/Marlin: backend PCIe: rearrange PDB medium priority interrupt handlers( SCGCQ01110330 ) 
 - ComboSerdes: update Aero Makefile to include new compile options	( SCGCQ01113261 ) 
 - Aero: more makefile changes	( SCGCQ01113981 ) 
 - Ventura A0: Allow ISTWI controller to core mapping to 1:1( SCGCQ01115202 ) 
 - Aero: Add support for ARM GIC 500( SCGCQ01116603 ) 
 - Aero: add device support for Aero( SCGCQ01116610 ) 
 - Ventura B0: Update RMC PCE Hot Reset sequence to use Chip Reset instead of the workaround for A0 that used SysLite Reset instead.( SCGCQ01117310 ) 
 - IOP: Remove VENTURA_PORTING from IOP code (misc, msg and pwrmgmt	( SCGCQ01123894 ) 
 - Aero: create aero base address map( SCGCQ01123955 ) 
 - Ventura: IOP Workaround and PCE Chip Revision Changes for B.0( SCGCQ01123969 ) 
 - Ventura: add Link field to the PCIe Link configuration pages (part 1	( SCGCQ01124182 ) 
 - ComboSerdes: Configure OOB SAS/SATA TXEQ	( SCGCQ01125424 ) 
 - IOP: MCTP I2C interrupt config and structure alignment improvements( SCGCQ01125427 ) 
 - IOP: MCTP over I2C transmit buffer alignment correction	( SCGCQ01127461 ) 
 - Ventura/Marlin: backend PCIe: support for SRIS enable in PCIe IO Unit page 1 phy data( SCGCQ01130582 ) 
 - Make: Modify compiler, assembler, and linker options to ensure proper alignment	( SCGCQ01131963 ) 
 - BUILD: Modify compiler, assembler, and linker options to ensure proper alignment on Ventura( SCGCQ01132205 ) 
 - Ventura: Disable NVMe in default NVDATA	( SCGCQ01132935 ) 
 - NVMe: handful of changes for NVMe SGL support( SCGCQ01134129 ) 
 - MPI2.6: Added new image type and flash region definitions( SCGCQ01136127 ) 
 - Ventura: SPI library: Add support to Macronix Flash 128Mb MX25U12835FXDI	( SCGCQ01136315 ) 
 - ComboSerdes: Update SasPhyPRegs.h for SAS4( SCGCQ01141006 ) 
 - pl: backend PCIe: add compile option for hot reset on PCIe link up( SCGCQ01141218 ) 
 - MPI 2.6: Add new clean tool options( SCGCQ01141732 ) 
 - Ventura: Update MST with current MST info on timer error completions to IOP	( SCGCQ01141751 ) 
 - Ventura: Add fault for unexpected CSW error interrupts( SCGCQ01143296 ) 
 - Enable interface function to dump SD Channel error interrupt info( SCGCQ01143336 ) 
 - Ventura: Add customer-specific partial NVDATA( SCGCQ01144968 ) 
 - MPI 2.6: Add two new reason codes to Active Cable Exception Event Data( SCGCQ01146583 ) 
 - Ventura: SPI library: support FLash Macronix 256Mb 1.8v MX25U25635FXDI-10G( SCGCQ01149975 ) 
 - pl: NVMe: additional encapsulated request error reporting( SCGCQ01150880 ) 
 - Host DPA power state change requests tied to controller's power mode change handlers	( SCGCQ01151427 ) 
 - Configure unique receiver DFE settings for 3Gbps SAS/SATA( SCGCQ01158802 ) 
 - Add board name to (iop show ver( SCGCQ01161686 ) 
 - IOP: MCTP: Add MCTP status CLI command( SCGCQ01162907 ) 
 - Update Man page 41 with TxEq values provided by Systems Engineering.	( SCGCQ01164684 ) 
 - ComboSerdes: Update TX EQ Settings Per SCGCQ01164659	( SCGCQ01164711 ) 
 - ventura/Marlin: Port firmware signing firmware from Gen3	( SCGCQ01165402 ) 
 - Ventura: Rename Obsolete Resources In Mfg. Page 9 - XSD Files( SCGCQ01167302 ) 
 - Ventura B0: backend PCIe: enable NVMe completion starvation prevention	( SCGCQ01169187 ) 
 - Ventura: Auto backplane type detection and configuration support	( SCGCQ01172310 ) 
 - Ventura/Marlin: backend PCIe: handle switch attached hot add max payload size mismatch( SCGCQ01172361 ) 
 - IOP: Doxygenate IOP Fault codes and prepare Error Code Guide document( SCGCQ01177469 ) 
 - MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP( SCGCQ01180886 ) 
 - PLI/DOC: Update Doxygen to 1.8.12( SCGCQ01181315 ) 
 - Ventura: Create utility to modify package version and package name( SCGCQ01188381 ) 
 - Ventura: SPI library: Reduce SPI flash write time in manual mode for performance	( SCGCQ01194973 ) 
 - Ventura: On firmware download compare new SBR with old SBR and notify host if there is a change( SCGCQ01194989 ) 
 - Utility: Update MemCfg utility( SCGCQ01207514 ) 
 - MPI 2.5: Add two new reason codes to Active Cable Exception Event Data( SCGCQ01208954 ) 
 - Ventura/Marlin: backend PCIe: allow user to disable ECRC for testing	( SCGCQ01209929 ) 
 - Update TxEQ settings	( SCGCQ01212690 ) 
 - Update TxEQ settings	( SCGCQ01212712 ) 
 - CSW: Ventura jitter changes	( SCGCQ01212870 ) 
 - MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0	( SCGCQ01213028 ) 
 - MPI2.6: Mfg7 support for arbitrary starting slot number	( SCGCQ01213267 ) 
 - Ventura: Print decimal versions( SCGCQ01217493 ) 
 - Documentation: Update PLI and Error documents with feedback from the technical publications team	( SCGCQ01223765 ) 
 - Ventura B0: Create doxygen support framework for VSES documentation	( SCGCQ01225423 ) 
 - New set of serdes settings( SCGCQ01229302 ) 
 - Ventura: Move firmware update copy process to main firmware to avoid PCE problems( SCGCQ01230723 ) 
 - Ventura B0: Update VSES Specification document.( SCGCQ01235306 ) 
 - Ventura/Marlin: When the SPICO code fails checksum, Patch SPICO Signature and Checksum( SCGCQ01240422 ) 
 - Updated CSW library	( SCGCQ01242238 ) 
 - OEM NVMe backplane detection, PCIe Reset and LED management over I2C	( SCGCQ01253925 ) 
 - Ventura: Add capability to firmware download to update CBB BACKUP( SCGCQ01257997 ) 
 - MPI 2.6: Add new firmware download type (CBB BACKUP( SCGCQ01258005 ) 
 - Ventura: Implement the remaining bits in the Clean Tool( SCGCQ01258007 ) 
 - IOP: Simplified NVData and Package version print on UART output	( SCGCQ01258333 ) 
 - Marlin RMC: Adjust AVSO programming algorithm with values provided by hw team( SCGCQ01260474 ) 
 - Updated Marlin B0 SATA Rx EQ Values( SCGCQ01261262 ) 
 - Ventura/Marlin: allow IOP to direct PL to not allocate secondary CPU queues( SCGCQ01263302 ) 
 - pl: NVMe: new alignment requirement for NVMe SGLs( SCGCQ01272065 ) 
 - Ventura: Validate PortSelected field passed to snooping config function( SCGCQ01273125 ) 
 - MPI 2.6: Device side PCIe SRNS flag	( SCGCQ01276256 ) 
 - Ventura/Marlin: backend PCIe: NVMe core exception and completion queue handler optimization( SCGCQ01281240 ) 
 - Ventura: Defeature using Man page 12 slot info option( SCGCQ01282530 ) 
 - MCTP over PCIe Access Control( SCGCQ01283644 ) 
 - Add ability to field upgrade CPLD on HBA boards( SCGCQ01283645 ) 
 - Ventura/Marlin: Modify CFGI to allow migrations if there is only a minor revision change	( SCGCQ01287390 ) 
 - Aligned NVDATA and Package version UART prints.( SCGCQ01289012 ) 
 - Enabled SAS protocols with SSC( SCGCQ01293498 ) 
 - MPI 2.6: Add new firmware download type (CPLD IMAGE( SCGCQ01305760 ) 
 - NVDATA: Update configuration files( SCGCQ01319710 ) 
 - Ventura signed firmware support for PKCS7 certificate digest	( SCGCQ01320684 ) 
 - SGPIO: Assign group ID to the sgpio backplane connectors that did not report bays presence( SCGCQ01327271 ) 
 - Ventura: Enclosure Mgmt optimizations and enhancements( SCGCQ01328437 ) 
 - Ventura: Add TM IOCStatus to TM Logger( SCGCQ01336984 ) 
 - Enhancement to SPI Library error reporting( SCGCQ01346552 ) 
 - Ventura: Add support for OEM specific NVMe backplane detection and slot LED control	( SCGCQ01346574 ) 
 - Adding support for SEP reset by controller FW at start of day through CPERST# signal	( SCGCQ01353161 ) 
 - Added support for Bios signing and ported signtool to Windows( SCGCQ01354846 ) 
 - Warning removal 167	( SCGCQ01365168 ) 
 - Warning removal 550	( SCGCQ01365173 ) 
 - Warning removal 676	( SCGCQ01365174 ) 
 - MPI 2.6: Add Aero PCI Device IDs	( SCGCQ01373008 ) 
 - Enable I2C polling for drive presence detection in VPP Type B backplanes with NVMe support.( SCGCQ01375330 ) 
 - Ventura: Print NVMe Status Code Fields to ring buffer( SCGCQ01377133 ) 
 - pl: NVMe: dump request message and SGL on device IO failure( SCGCQ01377671 ) 
 - Enable WB mode for JBOD EPD( SCGCQ01378163 ) 
 - pl: backend PCIe: add ECRC error status	( SCGCQ01378999 ) 
 - OEM backp lane bring up on MR( SCGCQ01379829 ) 
 - Ventura 7.4 - All R/W IO's on EPD LD's need to be forced to DCDB IO Path in FW( SCGCQ01380047 ) 
 - Track Cmd Block Initiate TM when FP io or FW io outstanding.	( SCGCQ01389571 ) 
 - Task Management Changes, Bug Fixes On Unit Testing While Holding IOs in PL.( SCGCQ01392378 ) 
 - Add SPI library debug capabilities( SCGCQ01392854 ) 
 - Reduce the Number of Characters Logged into TTY During Error Handling( SCGCQ01397783 ) 
 - Add sbus read/write access functions to CLI( SCGCQ01403424 ) 
 - Enhance MR non-Critical frame mgmt to support LUN Reset in PL( SCGCQ01406415 ) 
 - Ventura B0:(UBM	( SCGCQ01412194 ) 
 - Enable I2C polling for drive presence detection in UBM backplanes with NVMe support.	( SCGCQ01412198 ) 
 - Controlling Slot Locate/Fault LEDs in a backplane which implements UBM.( SCGCQ01412209 ) 
 -	( SCGCQ01412644 ) 
 - MPI 2.6: Add new reason code to PCIE Device Status Change Event( SCGCQ01416515 ) 
 - SPILib: Prevent firmware downgrade if older version does not support SPI flash being used.( SCGCQ01417738 ) 
 -	( SCGCQ01419081 ) 
 - pl: NVMe: NVMe task management modifications	( SCGCQ01419083 ) 
 - MR 7.5 - Add 0x15(21	( SCGCQ01425122 ) 
 - Replace POM0 usage with SysDma	( SCGCQ01430023 ) 
 - Ventura: NVMe 1.3 Support: Firmware Update Granularity( SCGCQ01430672 ) 
 - Ventura: NVMe 1.3 Support: Namespace Optimal IO Boundary	( SCGCQ01430674 ) 
 - pl: NVMe: IO breakup structure modification( SCGCQ01431067 ) 
 - Ventura: NVME 1.3 Support: Add new Status Codes to header files( SCGCQ01434061 ) 
 - Add Test Link Diagnostic API	( SCGCQ01436268 ) 
 - pl: NVMe: don't require a resource frame for some SCSI-NVMe translations	( SCGCQ01436612 ) 
 - Add NVRAM_INTERCORE_REQUEST_INFO_REQUEST_SKIP_WAIT to API( SCGCQ01437234 ) 
 - Provide OEMs ability to select either I2C or PCIe as an out of band transport( SCGCQ01445045 ) 
 - Add a new structure to provide OEMs ability to switch to select either I2C or PCIe as an out of band transport( SCGCQ01445048 ) 
 - Enable FlowControl using XON/XOFF( SCGCQ01445058 ) 
 - PL: Add firmware support for depopulation of SATA drives	( SCGCQ01445877 ) 
 - (SATA Only( SCGCQ01448576 ) 
 - MPI 2.6: PCIe Device Page 2 reporting Namespace Optimal IO Boundary(NOIOB( SCGCQ01449138 ) 
 - Provide OEMs ability to select either I2C or PCIe as an out of band transport( SCGCQ01450390 ) 
 - New: Ventura LD de-allocation support on SAS/SATA SSDs through UNMAP/WRITE SAME on non-PARITY, non-DIF volumes( SCGCQ01451570 ) 
 - Ventura: Re-order pl dbg to put most useful, less verbose prints first( SCGCQ01454612 ) 
 - UART command to enable switching the NVMe clocking mode( SCGCQ01455706 ) 
 - PL: Use Sense Data from SATA Log Page 10 when querying Log Page 10( SCGCQ01459375 ) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_5.0 - 05.250.00.00 MR PL-SCS Libs( SCGCQ01459394 ) 
 - Added MPI2_MR_PARAMS_PAGE_0.OOBMaxPacketSize	( SCGCQ01460789 ) 
 - Ventura: Change iopiDiagCmdReadMem( SCGCQ01462690 ) 
 - New feature to disable JBOD through NVDATA change if requested by customer( SCGCQ01463522 ) 
 - Ventura: Modify plDiagCmdShowRegister( SCGCQ01464914 ) 
 - pl: backend PCIe: reduce firmware initiated PCIe transaction wait time( SCGCQ01465016 ) 
 - Update description of MR_DCMD_CTRL_PERSONALITY_SET Dcmd( SCGCQ01467149 ) 
 - Reading UNMAP support value through NVDATA( SCGCQ01472058 ) 
 - Low lotency path cleanup	( SCGCQ01481026 ) 
 - Improve SCons dependency tools( SCGCQ01496996 ) 
 - Resetting discovered flag when prepare for endpoint discovery control command.( SCGCQ01506822 ) 
 -	( SCGCQ01518586 ) 
 - Disable deallocation support in Ventura 7.5	( SCGCQ01531388 ) 
 - FBU345 should show as CVPM05	( SCGCQ01558893 ) 
 - Provide print in termlog that shows which I2C address is used for the LED signaling of NVMe drives( SCGCQ01559697 ) 
 - BIOS Handshake breaks Manufacturing Environment, need change in TTY and/or add timeout in FW for BIOS Handshake( SCGCQ01575182 ) 
 - 7.5 R1 performance change request.( SCGCQ01614688 ) 
 - Add support in FW for new LL hung connection timer/controls in HW( SCGCQ00105465 ) 
 - (IOP-Only	( SCGCQ00125129 ) 
 - Gen 3: update MPI v2.5 header files( SCGCQ00128142 ) 
 - New L3 cache hardware header file( SCGCQ00129841 ) 
 - MPI2: add optional vendor-unique region to MPI2_SCSI_IO_REQUEST structure( SCGCQ00132183 ) 
 - TBM: Incorporate a FW header in the Extended Buffer for the parser( SCGCQ00132403 ) 
 - (IOP-Only( SCGCQ00132479 ) 
 - Thunderbolt: The uart clock has been changed in B0( SCGCQ00132858 ) 
 - Firmware build needs to link pre-built PL library, instead of compiling it with the rest of firmware	( SCGCQ00134475 ) 
 - Gen3 PwrMgmt: Extend Thunderbolt's "half speed mode" with support for "quarter speed mode" and "eighth speed mode"( SCGCQ00135539 ) 
 - Gen3 PwrMgmt: Add "Presence Detect" capability for direct-attached phys	( SCGCQ00135543 ) 
 - PL: review usage of TxDmaStart Busy( SCGCQ00135548 ) 
 - MPI2 - additional IR status information( SCGCQ00136201 ) 
 - Gen3 PwrMgmt: Add PL support for TxDMA, RxDMA, RxEEDP light sleep/deep sleep/shutdown modes( SCGCQ00136933 ) 
 - (IOP-Only( SCGCQ00137508 ) 
 - (IOP-Only( SCGCQ00140387 ) 
 - Gen3 Manufacturing Config Pages 11,30 and 31( SCGCQ00141619 ) 
 - Gen3: Bringup PBAM Flash	( SCGCQ00141693 ) 
 - PL must start/stop timers for IOs if IOP is using Cuda Timing Wheel and PL starts IO directly to colt( SCGCQ00141735 ) 
 - Update project to the Phase 7 MPI Header Files( SCGCQ00141743 ) 
 - (IOP-Only( SCGCQ00144016 ) 
 - Dev Test: TLR jammer scripts check in( SCGCQ00144391 ) 
 - Add PLI control request for PauseHostRequest Cuda bit on/off	( SCGCQ00144626 ) 
 - FPE: Upgrade the FPE Init process to initailize Detroit memory more elegantly( SCGCQ00145070 ) 
 - Gen3 PowerMgmt: Gen3-ize PCIe Link Speed & Width Change Code	( SCGCQ00146799 ) 
 - Update RMTFLASH for GEN-3 Invader( SCGCQ00146810 ) 
 - CFGI: add support for MFG Pages 30 and 31( SCGCQ00146854 ) 
 - (IOP	( SCGCQ00147874 ) 
 - Update PLI to allow passing of VF Request Q sizes( SCGCQ00148029 ) 
 - Update iopiMemoryMove Function for Gen3	( SCGCQ00148770 ) 
 - TBM: Update ForceFlush handling	( SCGCQ00149047 ) 
 - FPE: Add PLI contreq function to support "Route All To Exceptoin Queues" bit in FPE Control reg( SCGCQ00149686 ) 
 - pl: Allow sense data for ATAPI device to go to other address space than just pci	( SCGCQ00150256 ) 
 - FPE: Firmware changes for Detroit 1.2 EDS release( SCGCQ00150513 ) 
 - FPE: Dev Test Customization( SCGCQ00151752 ) 
 - Gen3: PL Light( SCGCQ00152450 ) 
 - Control Q disabling needs to pause Cuda as well( SCGCQ00152670 ) 
 - Gen3 IR - Data Scrub Duration Update	( SCGCQ00154735 ) 
 - Gen3: Support FPE NVDATA changes	( SCGCQ00155854 ) 
 - Change the mid validation code in PL to filter out mid 1 as well	( SCGCQ00156042 ) 
 - pl: make sure TM and hw clean up code doesn't use mid 1( SCGCQ00156442 ) 
 - FPE - prevent auto reenable of FP on TM completion.( SCGCQ00156594 ) 
 - (IOP-Only( SCGCQ00157015 ) 
 - MPI2: MFG 7 update: method to link ISTWI devices, GPIO, PHYs of a SAS connector( SCGCQ00159010 ) 
 - MPI 2.5: Obsolete MPI2_RAID_VOL_CREATION_BACKGROUND_INIT	( SCGCQ00159395 ) 
 - Update MemCfg utility for SAS3FW compatability( SCGCQ00160081 ) 
 - FPE: add pli control requests to adjust the cuda auto trace levels( SCGCQ00160522 ) 
 - Explicitly set the Flags field in IR’s calls to iopiMemoryMove( SCGCQ00162573 ) 
 - MPI2: reserve some FWDownload ImageType values for product-specific use( SCGCQ00162597 ) 
 - Third set of DDR3 changes for Elektra/Invader( SCGCQ00162738 ) 
 - Performance counters - add FW counters similar to FPE and make them all visible to host via MPI config page( SCGCQ00163008 ) 
 - Remove PBSRAM support( SCGCQ00163164 ) 
 - Implement TCM for Invader( SCGCQ00163173 ) 
 - Enable L1/L2 data caching for Invader FPGA( SCGCQ00163174 ) 
 - Bring up I2C support on Invader	( SCGCQ00163177 ) 
 - MPI 2.5: review SGE Flags for Local bit and Data Location Address Space changes( SCGCQ00164407 ) 
 - First set of Cobra specific DDR3 library changes	( SCGCQ00168783 ) 
 - Update TM code to comply with new cuda pend list cleanup	( SCGCQ00168994 ) 
 - Add print out of the Abort list for a TM when it causes a fault.	( SCGCQ00170549 ) 
 - NVDATA defaults update for FPGA and A0 Silicon( SCGCQ00172450 ) 
 - Changes to DDR3 builds( SCGCQ00172764 ) 
 - Detroithw.h changes to support Detroit EDS 1.35( SCGCQ00173443 ) 
 - update the xsd file for the palladium build( SCGCQ00173631 ) 
 - Changes to DDR3 library to support linking with SAS3 controller firmware	( SCGCQ00175235 ) 
 - Report to host the offset of first EEDP error( SCGCQ00175700 ) 
 - Update chip feature identification firmware for Invader controller family( SCGCQ00178655 ) 
 - FPE: Investigate optimizing FPE invalid descriptor handling( SCGCQ00180215 ) 
 - Define LTRACE registers( SCGCQ00181694 ) 
 - Create NVData files for Fury	( SCGCQ00181723 ) 
 - More NVDATA mfg cfg pg 2 updates for Invader eval board( SCGCQ00186027 ) 
 - Update CreateScripts.cmd for Invader Silicon	( SCGCQ00186459 ) 
 - update so pl release includes both the current DEBUG library and also a nonDEBUG library	( SCGCQ00188811 ) 
 - Update UART clock macro definitions	( SCGCQ00192541 ) 
 - Ethernet: Update driver for efficiency, change EthHal structure for debug( SCGCQ00194441 ) 
 - ONFI: Prepare for HW automated memory offload( SCGCQ00194676 ) 
 - ONFI: Issue MAP Commands	( SCGCQ00194679 ) 
 - Gen3: Implement Xmodem Interface	( SCGCQ00205236 ) 
 - Increase the frequency of the SHELL clocks from 250 MHz to 500 MHz( SCGCQ00207056 ) 
 - Create a processor monitor for tracking of processor time allocation	( SCGCQ00207617 ) 
 - Porting up Gen2 changes from Phase 11 for ISTWI and Enclosure Management CSETs( SCGCQ00208724 ) 
 - TxCtxMgr Interrupt handling cleanup( SCGCQ00209353 ) 
 - ONFI: Updates to the MAP Commands( SCGCQ00209886 ) 
 - Gen3: FW updates for FPGA to work with latest bitstreams.( SCGCQ00213008 ) 
 - Update SnC Method (08/16/2011 3:54 PM( SCGCQ00213372 ) 
 - Gen3: Update LTRACE dump format	( SCGCQ00217177 ) 
 - TxFM and CtrlQ code cleanup and debug improvements( SCGCQ00222848 ) 
 - Invader A0: Target Mode print optimization( SCGCQ00223545 ) 
 - Update TLBs to reflect Memory Coherency bit( SCGCQ00224498 ) 
 - Active cable support part one( SCGCQ00225179 ) 
 - Active cable support part two( SCGCQ00226322 ) 
 - Update GPIO NVData to Support 40 Entries	( SCGCQ00226718 ) 
 - MPI 2.5: IR - new Raid Action to enable the Fast Path( SCGCQ00227491 ) 
 - Update TM Hw context memory structure for gen3	( SCGCQ00227727 ) 
 - Add header file with memport #defines, to be included in common header files of binary DDR3lib releases( SCGCQ00229363 ) 
 - Customer requests common SAS3 header files to also include SAS2 only information	( SCGCQ00229951 ) 
 - Snapshot buffer updates for Gen3	( SCGCQ00231500 ) 
 - Change L3 and TLB setup to be compliant with DDR3 API document recommendations( SCGCQ00231516 ) 
 - Invader: Update lwIP to latest version( SCGCQ00237898 ) 
 - Gen3 IR - Enable PI support in NVDATA( SCGCQ00242621 ) 
 - BT 1629 WA implemenation	( SCGCQ00244096 ) 
 - Bring GEN-3 I2C support up to parity with GEN-2( SCGCQ00246028 ) 
 - Implement UART cmd to fault controller( SCGCQ00246669 ) 
 - IOP: Add Invader B0 SBR structure( SCGCQ00246851 ) 
 - MPI2: Update Hard Reset Algorithm with new timings( SCGCQ00250721 ) 
 - ONFI: Add 2 new interface APIs to access the DCR registers( SCGCQ00250934 ) 
 - Update builds to include B0 NVData( SCGCQ00254773 ) 
 - MPI2: Reserve Product Specific range for Event codes	( SCGCQ00258327 ) 
 - (IOP	( SCGCQ00259801 ) 
 - PL: Implement a vendor specific PLI control request( SCGCQ00269392 ) 
 - NVData updates for B0 SBR settings	( SCGCQ00280170 ) 
 - ONFI: Support physical addresses for DDR location to be offloaded( SCGCQ00291330 ) 
 - New API in ONFI Library to periodically callback during restore operation to update the progress	( SCGCQ00300692 ) 
 - Update Cli Toolbox Diag command handling per MPI 2.5 Rev E	( SCGCQ00308513 ) 
 - pl pci: Enumeration and Configuration	( SCGCQ00308793 ) 
 - PCIe interrupt (INTx, MSI/MSI-x	( SCGCQ00308797 ) 
 - MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1( SCGCQ00310439 ) 
 - Remove modification of CTRL_RAW parameter inside ddr3 library interrupt handler API	( SCGCQ00313866 ) 
 - (NVDATA	( SCGCQ00316358 ) 
 - Enable all fatal L2 error interrupts	( SCGCQ00328716 ) 
 - Added a PLI Control Request Operation To Get Count of Known EDFB (DataBolt( SCGCQ00333765 ) 
 - Hardware changes from Invader for Boot	( SCGCQ00338455 ) 
 - NVMe Mode Sense and Mode Select translations	( SCGCQ00338540 ) 
 - Various NVMe related changes	( SCGCQ00341755 ) 
 - (FPGA( SCGCQ00362502 ) 
 - Distribution of PCI space obtained from the host amongst PDB PIM windows.( SCGCQ00362905 ) 
 - Backend PCIe device memory allocation (part 1	( SCGCQ00365971 ) 
 - Support for new config pages PCIe IO Unit Page0,1, PCIe device pages 0,1 described in MPI 2.6 specification( SCGCQ00377454 ) 
 - (PL-IOA	( SCGCQ00377476 ) 
 - NVMe firmware-only mode( SCGCQ00378032 ) 
 - USB : [invader]1813 - CDC Issues in USB Atlantic Controller( SCGCQ00381371 ) 
 - (IOP	( SCGCQ00386217 ) 
 - Use dedicated Stang NVMe chain area	( SCGCQ00391063 ) 
 - Update Silverhawk and Prevail PIM/POM settings to support Subtractive routing( SCGCQ00394770 ) 
 - Added handlers for PCIe errors( SCGCQ00400046 ) 
 - Add PCIe Link config pages to read and configure PCIe link error and event counters	( SCGCQ00400394 ) 
 - Dauntless: Implement PLI control request for MR to set snoop regions in stang and PDB.( SCGCQ00412920 ) 
 - Add SOP and PQI header files	( SCGCQ00423525 ) 
 - MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL( SCGCQ00438437 ) 
 - SOP Initialization( SCGCQ00442840 ) 
 - Add support for PCIe prefetchable memory BARs( SCGCQ00449047 ) 
 - NVMe: FxCore IoError handling( SCGCQ00461439 ) 
 - SAS3.5 ARM Port - Add automated MMU Region Mapping Capability( SCGCQ00483912 ) 
 - Print additionl information on PCIe Error Messages and Fault on unhandled PCIe errors( SCGCQ00487994 ) 
 - Update TCC to version 0.9.26	( SCGCQ00492508 ) 
 - Cleanup the TxDMA dual context and DMA groups code based on new HW functionality in Intruder SAScore	( SCGCQ00496009 ) 
 - (IOP-Only( SCGCQ00498642 ) 
 - Allocate from IOA Local RAM( SCGCQ00521570 ) 
 - Ventura: GIC - Generic Interrupt Controller	( SCGCQ00521685 ) 
 - Ventura: Create HW header file describing CCN-505 Configuration Registers( SCGCQ00521690 ) 
 - Ventura: IOA – Impala IO Accelerator Cuda Block Bring Up	( SCGCQ00522530 ) 
 - Ventura: Create C header files for CIB (Core Interface Blocks( SCGCQ00572483 ) 
 - (VENTURA BUILD( SCGCQ00599359 ) 
 - Ventura: Port power-on self-test (POST, BL( SCGCQ00599962 ) 
 - Ventura: Parent ER - Port misc processor features for ARM( SCGCQ00600384 ) 
 - Ventura: Port PPC FAULT routines to ARM	( SCGCQ00606223 ) 
 - Ventura: MSS - FPGA DDR functional( SCGCQ00606278 ) 
 - Enterprise preparation: root complex organization( SCGCQ00613905 ) 
 - Rename all instances of IRQ_SAS interrupts to IRQ_SAS0( SCGCQ00614956 ) 
 - Ventura: Create fast POST memory routines using Neon similar to ARM memcpy( SCGCQ00622834 ) 
 - PL support for multiple SAS cores during initialization	( SCGCQ00623972 ) 
 - Modify PLI interface to take SasCoreNum parameter( SCGCQ00630403 ) 
 -	( SCGCQ00633869 ) 
 - Ventura: NVMe: update device information after a Format Unit	( SCGCQ00639223 ) 
 - Ventura: SerDes header file changes	( SCGCQ00643953 ) 
 - Ventura: IOA NVME SOP Hang Detection (CR-18	( SCGCQ00647800 ) 
 - Modify the xsd files to limit the SAS Phys to two for Intruder FPGA and Include/exclude appropriate config pages to it.( SCGCQ00648191 ) 
 - Add build option for customer specific PL Library build	( SCGCQ00658152 ) 
 - Ventura: SPI library update to SPI Flash access in Ventura( SCGCQ00664307 ) 
 - Intruder: Register dump of all SAS Cores	( SCGCQ00665865 ) 
 - Ventura: Backend PCI - generate PCI reset from TM( SCGCQ00674370 ) 
 - Ventura: Enable DCR access macros for ARM( SCGCQ00682711 ) 
 - Add multiple SAS core support for Diag Snapshot feature( SCGCQ00684391 ) 
 - Intruder FPGA: use 2MB of L3 cache as OCM( SCGCQ00685184 ) 
 - Migrate GHS toolchain to version 6.1.4( SCGCQ00685242 ) 
 - Review Intruder EDS v1.9 for CCR changes that apply to FW( SCGCQ00689788 ) 
 - Ventura: backend PCIe: link to root complex mapping	( SCGCQ00692020 ) 
 - Ventura: Implement new PCIe Discovery SM	( SCGCQ00694262 ) 
 - Intruder: Manufacturing Page 11 NVDATA changes for BoardPowerRequirement Setting( SCGCQ00700740 ) 
 - VENTURA: Port I2C Support in Ventura	( SCGCQ00701754 ) 
 - Intruder SBR update	( SCGCQ00712527 ) 
 - Add Multi SAS Core support to initiator added functionaility	( SCGCQ00713914 ) 
 - Ventura: Add support for PCIe devices using DDR in IT	( SCGCQ00717115 ) 
 - Ventura: Enable the IOA interrupts( SCGCQ00718616 ) 
 - PL: cleanup of #if INVADER( SCGCQ00728717 ) 
 - Ventura: Create CCI-400 Header File( SCGCQ00731687 ) 
 - Ventura: Enterprise: update headers for new EDS( SCGCQ00756824 ) 
 - Ventura: Add Loose Alignment and Lock/Unlock to SPI library( SCGCQ00757681 ) 
 - Ventura: Implement Build Optimizations Recommended by ARM( SCGCQ00759482 ) 
 - Ventura: Assembly Language Upgrades Recommended by ARM( SCGCQ00759486 ) 
 - Ventura: Update and/or Port Misc ARM C Functions and Macros( SCGCQ00759728 ) 
 - Ventura: Verify and/or Fix Various Decriptor Settings( SCGCQ00759734 ) 
 - Migrate DDR3 intruder library to new set of tools( SCGCQ00768996 ) 
 - Ventura: Add restart capability to PCIe discovery( SCGCQ00771838 ) 
 - Ventura: Implement PCIe Discovery Event Replay( SCGCQ00771839 ) 
 - Ventura: enable CCI performance monitor( SCGCQ00771904 ) 
 - Ventura: enable Shell performance monitor( SCGCQ00771905 ) 
 - Ventura: Add FPGA Script Support for DS-5 5.19( SCGCQ00777865 ) 
 - Ventura: Program SPI FLASH using manual mode commands( SCGCQ00780123 ) 
 - Ventura: Remove PL private files from the IT build( SCGCQ00785195 ) 
 - Backend PCIe: remove 'pl pci cap' console command( SCGCQ00786396 ) 
 - Ventura: Add support for sas2parser 10.00.00.00( SCGCQ00786411 ) 
 - Ventura: MSS - SPD Data Function for FPGA( SCGCQ00787495 ) 
 - VENTURA: Update CLI commands for SPI module debug and test( SCGCQ00791903 ) 
 - Ventura: Modify code for compatibility with Silverhawk core( SCGCQ00796039 ) 
 - Improve the PL_ASSERT macro usage.( SCGCQ00804858 ) 
 - Intruder: New Config Pages for ISTWI Controller and Device Information( SCGCQ00806204 ) 
 - Ventura: RMC boot code and makefiles	( SCGCQ00810261 ) 
 - Ventura: Update code to compiler 5.0.5( SCGCQ00813831 ) 
 - Add 3DS capability( SCGCQ00814795 ) 
 - Ventura: MSS - DDR4 Miscellaneous Support( SCGCQ00814869 ) 
 - Intruder: update Product ID in build process	( SCGCQ00814928 ) 
 - Ventura: Update FMU Queue Initialization	( SCGCQ00820941 ) 
 - Ventura MSS - Move from MC eval mode algorithms to phy eval mode algorithms( SCGCQ00827542 ) 
 - Cleanup of PLI I/F PIM/POM struct members( SCGCQ00828947 ) 
 - Ventura SW A/R: AER interrupt handling for Switch topology (ER( SCGCQ00830951 ) 
 - Updates to PLI_RUNTIME_CONFIG( SCGCQ00831058 ) 
 - Add NumberOfSEDs and NumberofSEDMids to mfg page 9( SCGCQ00831065 ) 
 - Marlin: Host Side x16 Support( SCGCQ00832634 ) 
 - Intruder A0: Set SYS PLL Frequency to 1200 MHz( SCGCQ00841118 ) 
 - Ventura FPGA: increase max number of PCIe devices to 16 in NVDATA( SCGCQ00848369 ) 
 - Ventura: backend PCIe: hide backend PCIe devices from virtual functions (part 1	( SCGCQ00854613 ) 
 - Ventura MSS: Add MemPort header file to list of files distributed with the library( SCGCQ00855676 ) 
 - Code changes to get PCI hot reset working( SCGCQ00857498 ) 
 - Ventura: Add MSS MemPort (MegaTron( SCGCQ00861719 ) 
 - IOP: Move CFGI library related files to config directory	( SCGCQ00861886 ) 
 - Ventura: Add support for handling AXI interrupts in SAS Core	( SCGCQ00862457 ) 
 - Ventura: Prepare Ventura build for predicted SBR and Firmware Size( SCGCQ00865228 ) 
 - MPI 2.6: add new feature to control NVMe SGL format( SCGCQ00872169 ) 
 - Update the ComboSerdes Library to AAPL 2.2.1	( SCGCQ00877408 ) 
 - IOP: Hardware Workaround Cleanup for Intruder( SCGCQ00879206 ) 
 - Ventura: backend PCIe: clean up some TODOs (part 2( SCGCQ00884601 ) 
 - Tiger/Stryker: Add new buildtype for Liger(SE( SCGCQ00890386 ) 
 - Tiger: Update bootloader for the CPU used by Tiger( SCGCQ00892724 ) 
 - Ventuara - DDR Frequecy scaling - Debug Support( SCGCQ00892976 ) 
 - Ventura: SPI library integration update to common shared library	( SCGCQ00893546 ) 
 - Tiger: Various tweaks to allow FPE usage on FPGA	( SCGCQ00894300 ) 
 - Enabled SASSDChannel Interrupts( SCGCQ00894717 ) 
 - IOP: Update PBAM offsets with Tiger/Stryker configuration( SCGCQ00897540 ) 
 - IOP: Update Tiger base addresses	( SCGCQ00904515 ) 
 - Ventura: Update firmware to the latest revision of NVMe SCSI Translation Reference( SCGCQ00905171 ) 
 - Remove Dauntless specific code from CFGI library	( SCGCQ00905992 ) 
 - Remove Dauntless platform specific code from Common Boot Block( SCGCQ00906013 ) 
 - Ventura: Add ocmscrub and remote flash binaries for test debug( SCGCQ00907908 ) 
 - Tiger/Stryker: CSR init	( SCGCQ00907988 ) 
 - Change Ventura build to create C++ library	( SCGCQ00909441 ) 
 - RMC error handling	( SCGCQ00910403 ) 
 - Rename iopiAvSerdes interface functions	( SCGCQ00910409 ) 
 - Build: Add Tiger/Stryker to build all script	( SCGCQ00910768 ) 
 - Ventura: add support for RMC watchdog( SCGCQ00910935 ) 
 - Add API for Protocol Mode Activation	( SCGCQ00911444 ) 
 - Ventura: Change SPI Internal structure to only contain internal information( SCGCQ00913596 ) 
 - BL: Update static extended image copy for Tiger	( SCGCQ00913638 ) 
 - Ventura B0: backend PCIe: changes for IOA stall prevention	( SCGCQ00914682 ) 
 - Ventura: add PCE Hardware Settings for SBR	( SCGCQ00914684 ) 
 - Ventura : MSS : LRDIMM Support : Training between DB and DRAM( SCGCQ00916711 ) 
 - Configure SAS 12G TxEq REF1, REF2 and NO-REF presets	( SCGCQ00918245 ) 
 - Tiger IOP: Handle clearing stale doorbell interrupt to support CLI Toolbox during fault( SCGCQ00918496 ) 
 - Ventura: Remove VENTURA_PORTING from ARM Initialization/Utilities.( SCGCQ00922893 ) 
 - IOP: Tiger/Stryker update to core enable function( SCGCQ00924365 ) 
 - Ventura: Update man pages 40 and 41 for first silicon( SCGCQ00925691 ) 
 - Ventura: backend PCIe: link down handling tweaks	( SCGCQ00925766 ) 
 - Tiger: Create psbmaverick.h Header File	( SCGCQ00926714 ) 
 - Create Tiger version of library	( SCGCQ00928530 ) 
 - IOP: Tiger: Update VIC Initialization( SCGCQ00928561 ) 
 - IOP: Tiger: Update time since start of day function	( SCGCQ00928566 ) 
 - Update miniDMA to work on Ventura.( SCGCQ00929185 ) 
 - IOP: Correct flash address( SCGCQ00932293 ) 
 - IOP: Tiger: Add Vector Table Support	( SCGCQ00932576 ) 
 - PL: Remove remote SAS core management( SCGCQ00938440 ) 
 - Ventura: Update NVDATA For Ventura Eval Board( SCGCQ00938441 ) 
 - Tiger FPGA: Add support to change FPGA bitstream from Base Mode to Tigermode during IT boot( SCGCQ00938845 ) 
 - Tiger: Implement Doorbell Interrupt routing	( SCGCQ00938853 ) 
 - Tiger: Update SIL on POM access.	( SCGCQ00939588 ) 
 - Tiger: Mpt endpoint PCIe config space read support( SCGCQ00940364 ) 
 - IOP: Tiger: Add periodic timer facilities( SCGCQ00940951 ) 
 - Tiger BL: Boot from Flash( SCGCQ00941578 ) 
 - Create separate header file for Tiger CCR register definitions( SCGCQ00944146 ) 
 - Tiger: add base nvdata files for Tiger( SCGCQ00947169 ) 
 - Warm Start Library Initialization Routings Added	( SCGCQ00951537 ) 
 - Tiger FPGA: removed reg write that isn't needed for FPGA	( SCGCQ00953320 ) 
 - Ventura: Add support to recognize harpoon storage processor with encryption( SCGCQ00953322 ) 
 - Create SBR and ROM image for Crusader.( SCGCQ00953723 ) 
 - VENTURA: Add support for additional SPI FLASH devices( SCGCQ00954923 ) 
 - Ventura: Add command to dump the SBR section of SPI flash( SCGCQ00963071 ) 
 - Ventura: Add CLI command to erase entire SPI flash( SCGCQ00979701 ) 
 - Ventura: Move location for rmtf.rom build in build all( SCGCQ00990538 ) 
 - Add JTAG Chip ID values for the AAPL library and SerDes tools( SCGCQ00993666 ) 
 - Ventura: Enable FW control of ConfigValid( SCGCQ00993797 ) 
 - Ventura: Update NVDATA Mfg. Page 9 Resources	( SCGCQ00994872 ) 
 - PL (Ventura( SCGCQ00997085 ) 
 - Tiger PL & IOP: First round of implementing SAS core memory translation	( SCGCQ01000544 ) 
 - Tiger: Implement firmware controlled PCIe message transmission on downstream ports.( SCGCQ01002884 ) 
 - Tiger: Implement firmware controlled PCIe memory TLP transmission on downstream ports.( SCGCQ01002890 ) 
 - Ventura Tiger support added to configure hardware to send IO to Tiger device	( SCGCQ01006667 ) 
 - Ventura: Add GLOBAL_MAX_CMD_CNT register to SHELL2AceLite header file( SCGCQ01007230 ) 
 - Ventura: Add Marlin images to IT release	( SCGCQ01012534 ) 
 - Tiger Ventura: handle IO replies from MPI device for IOs not started by FW path	( SCGCQ01012812 ) 
 - Tiger IOP: Configure messaging unit to send replies on same path as the data	( SCGCQ01019713 ) 
 - Ventura: Create initial partial for 9400-8i (Bristol TomCat( SCGCQ01020130 ) 
 - Ventura: Disable LR_SM prints by default	( SCGCQ01021261 ) 
 - Ventura: Update host side spico image( SCGCQ01024210 ) 
 - Aero: Add support for Clang (ARM V8( SCGCQ01025199 ) 
 - Ventura: Add additional PCE DBI Write Entries in SBR( SCGCQ01026165 ) 
 - Ventura Tiger: Implement internal Target Reset Task Management	( SCGCQ01027918 ) 
 - Tiger: Create SED product specific files	( SCGCQ01031950 ) 
 - Ventura MSS: DDR performance	( SCGCQ01031986 ) 
 - Create NVDATA for Dover (Crusader( SCGCQ01033595 ) 
 - Utilize both MC VREF ranges during initial and optimization of VREF values.( SCGCQ01034231 ) 
 - CSW: Update ComboSerdes library to use Spico FW 0C5F	( SCGCQ01038376 ) 
 - Ventura/Marlin: backend PCIe: allow assignment of additional memory space to backend PCIe devices( SCGCQ01040918 ) 
 - Ventura IOP : DDR4 Memory test feature	( SCGCQ01045575 ) 
 - Switch DS-5 scripts to use SR-IOV build path	( SCGCQ01045807 ) 
 - ComboSerdes: Updated Spico firmware to 1060 with corresponding interrupt sequences( SCGCQ01060045 ) 
 - ComboSerdes: Optimize code and data size	( SCGCQ01062234 ) 
 - Ventura: Defeature Ethernet in Present Build	( SCGCQ01066278 ) 
 - Ventura: Adapter Reset Workaround( SCGCQ01068990 ) 
 - Add SMID to frame state changed print, cleanup and consolidate args	( SCGCQ01071340 ) 
 - SCSI over PCIe (SOP	( SCGCQ01071351 ) 
 - ComboSerdes: Support Tiger Guinness CSW configurations( SCGCQ01083269 ) 
 - Ventura: Update default ARM tools to DS-5 Version 5.24( SCGCQ01083946 ) 
 - Enabled Accelerator Coherency Port( SCGCQ01086077 ) 
 - Aero: FPGA boot changes( SCGCQ01091721 ) 
 - Aero: changes to get PL to compile with clang( SCGCQ01094536 ) 
 - IOP: Initialize new fields in IOCFacts to 0( SCGCQ01095744 ) 
 - Comboserdes: Merge SAS3.5 and SAS4 CSW Support	( SCGCQ01105966 ) 
 - Backend PCIe: add some additional registers to a backend PCIe related header file( SCGCQ01107259 ) 
 - Ventura: Delete USB Library Code	( SCGCQ01107413 ) 
 - IT: backend PCIe: optimize toplevel PCIe-related interrupt handler( SCGCQ01107419 ) 
 - ComboSerdes: Update InterruptSequence RAM for SAS4( SCGCQ01107835 ) 
 - ComboSerdes: Update makefiles for Ventura/Aero( SCGCQ01110268 ) 
 - PL: Add doxygen comments to PLI and IOPI header files( SCGCQ01110308 ) 
 - Ventura: Add B0 Pl recognition( SCGCQ01112241 ) 
 - MPI 2.6: Add Sea Arch class and Product IDs( SCGCQ01116837 ) 
 - ComboSerdes: Changes for Aero Build( SCGCQ01116882 ) 
 - Aero: change Inline macro for ARM assembly( SCGCQ01118720 ) 
 - Ventura: Remove VENTURA_PORTING from IOP code (config, debug, flash and ethernet	( SCGCQ01123887 ) 
 - IOP: Remove VENTURA_PORTING from IOP code (init, startup, regions and sched	( SCGCQ01123893 ) 
 - Ventura MSS: interface changes( SCGCQ01123939 ) 
 - Ventura: SPI library: Add support to ISSI flash IS25WP128-RHLE 1.8v( SCGCQ01124637 ) 
 - Ventura: Report PCIe init status in IOC Exceptions( SCGCQ01130590 ) 
 - PLI: Finish doxygen comments to pliDefs.h( SCGCQ01132411 ) 
 - PLI: Add pli documentation to source control	( SCGCQ01134379 ) 
 - Ventura: Need to support erase functionality for MR Ventura cards in IT Bootloader( SCGCQ01140418 ) 
 - Ventura: Rename Obsolete Resources In Mfg. Page 9( SCGCQ01157973 ) 
 - Ventura: Add NVDATA for Customer HBA	( SCGCQ01165398 ) 
 - IOP and PL: Doxygen style comments to LogInfo header files( SCGCQ01167347 ) 
 - Ventura: Validate incoming SBR clock settings and Supported Devices before committing new firmware to flash( SCGCQ01173951 ) 
 - PL Doc: Correct Doxygen LaTeX output automatically( SCGCQ01183642 ) 
 - Ventura: Port NVDUMP utility to SAS 3.5	( SCGCQ01186238 ) 
 - Ventura: SPI library: Update SPI lock and unlock routines to match new SPI library version( SCGCQ01189014 ) 
 - Support VPP backplane LED management for NVMe x4 device Slots( SCGCQ01206050 ) 
 - Marlin/Mercator - Add B.0 Support for Mercator in the IOP( SCGCQ01229986 ) 
 - Update SAS serdes settings( SCGCQ01230719 ) 
 - Enable FLR as a product feature( SCGCQ01243549 ) 
 - Ventura/Marlin: backend PCIe: aggressively retry unreliable DA links during discovery( SCGCQ01264003 ) 
 - pl: NVMe: support for devices with large sector sizes( SCGCQ01275066 ) 
 - Ventura : Host Task management support( SCGCQ01300444 ) 
 - JBOD_Personality : Personality Management changes for Ventura( SCGCQ01301498 ) 
 - Implement aviSerdesGenericGetLibVersion( SCGCQ01305549 ) 
 - Enable Direct Attached Persistent Connections by default	( SCGCQ01306906 ) 
 - Add fault if device side spico fails to load	( SCGCQ01326658 ) 
 - PL: Additional debugging functionality( SCGCQ01328439 ) 
 - MPI 2.6: add NVMe SGL Data Block descriptor alignment flag( SCGCQ01339864 ) 
 - Reduced amount of data in pl dbg trace output( SCGCQ01394882 ) 
 -	( SCGCQ01402213 ) 
 - Enable support for isWBSupported API change in Firmware( SCGCQ01405382 ) 
 - To read the port Capabilities from backplane implementing UBM and to validate backplane configuration( SCGCQ01412195 ) 
 - MPI 2.6: Add ControllerResetTO to PCIe Device Page 2	( SCGCQ01416498 ) 
 - Ventura : HOST TM - Part II	( SCGCQ01436260 ) 
 - Enable using FIFOs in the UART HW( SCGCQ01439292 ) 
 - pl: NVMe: SGL translation performance tweaks	( SCGCQ01440247 ) 
 - Reduce time taken by host to initialize one SATA drive.	( SCGCQ01448575 ) 
 - Ventura/Marlin: Add support for Winbond 256Mbit SPI FLASH( SCGCQ01449325 ) 
 - PSOD with FW update using MCTP (iMR	( SCGCQ01451811 ) 
 - Cleanup MR FW log( SCGCQ01459401 ) 
 - PL: Add NVDATA option to gracefully handle invalid BP Type configurations( SCGCQ01464951 ) 
 - Skipping additional reserved registers when printing pl dbg trace( SCGCQ01468138 ) 
 - PL: Add Code to Correctly Determine Mid for Rx Context Non-automated Interrupts	( SCGCQ01472512 ) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_5.0 - 05.25.02.00 MR PL-SCS Libs( SCGCQ01481215 ) 
 - pl: NVMe: add debug print to the NVMe encapsulated failure path	( SCGCQ01487366 ) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_5.0 - 05.25.04.00 MR PL-SCS Libs( SCGCQ01498150 ) 
 - Remove deallocation support from Ventura 7.5	( SCGCQ01512568 ) 
 - SAS2FW: Need method to set Sentinel Interrupt Coalescing values( SCGCQ00034638 ) 
 - (IOP-ONLY( SCGCQ00113636 ) 
 - Gen 3: method to enable/disable FastPath capability on a per-device basis	( SCGCQ00116336 ) 
 - Port Layer error handling - cleanup/improve/optimize	( SCGCQ00126458 ) 
 - Gen3: TBM - Handle Trace Error	( SCGCQ00127747 ) 
 - Add handlign for new TxFM interrupt	( SCGCQ00129375 ) 
 - Update miniDMA code	( SCGCQ00129843 ) 
 - Gen3: add optional vendor-unique region to MPI25_SCSI_IO_REQUEST structure( SCGCQ00136677 ) 
 - Gen3 PwrMgmt: Integrate individual power management components into chip-wide power modes( SCGCQ00136952 ) 
 - MPI2: add PCI Device ID for Warhawk	( SCGCQ00137514 ) 
 - MPI2: add alternative defines for SGE Direction bit( SCGCQ00138259 ) 
 - MPI2: modify Host Based Discovery Action Request	( SCGCQ00140397 ) 
 - Add some FPGA workarounds currently needed to FPGA build	( SCGCQ00142976 ) 
 - Update Console Manager( SCGCQ00144056 ) 
 - Convert the SAS IOUnit control request for enable/disable of fast path to use PLI control request when going from IOP to PL( SCGCQ00145206 ) 
 - auto dump ring buffer to UART on fault( SCGCQ00148406 ) 
 - Invader Bootloader Updates( SCGCQ00149362 ) 
 - update cfgi_gnu.mak file to use latest MULTI	( SCGCQ00149386 ) 
 - (FPGA-Only( SCGCQ00149394 ) 
 - Update miscellaneous assembly language functions in crt0	( SCGCQ00153825 ) 
 - MPI 2.5: update PCI Device Ids for Invader / Fury( SCGCQ00155192 ) 
 - FPE - Unconfirmed Response Frame Handling( SCGCQ00155475 ) 
 - Add PCIe configuration space BIOS BAR (PIM2	( SCGCQ00156048 ) 
 - Add handling to various interrupts generated by the context non auto bit being set during task management.( SCGCQ00157017 ) 
 - FPE: Cuda Pend Queue Cleanup during TM( SCGCQ00160611 ) 
 - FPE: add some more debug to Requestor and Completor error/faults	( SCGCQ00163734 ) 
 - Modify DDR3 library to accommodate Cobra's 16bit data width.	( SCGCQ00168260 ) 
 - Turn on LL parity checking( SCGCQ00170270 ) 
 - Additional Invader IOP changes for DDR3( SCGCQ00170395 ) 
 - (Invader	( SCGCQ00170554 ) 
 - Add PCIE diagnostic commands to the console	( SCGCQ00171772 ) 
 - Update init image linker directive file for silicon	( SCGCQ00182266 ) 
 - nvdata update for invader A0	( SCGCQ00186498 ) 
 - Gen3: support SAS Notify Power Failure Expected (EPOW( SCGCQ00186531 ) 
 - Enable MSI-X multiple reply queues( SCGCQ00188933 ) 
 - Enable GPIO for Heartbeat and Link/Act lights( SCGCQ00189458 ) 
 - Clean up PPC476 header file( SCGCQ00194793 ) 
 - CLI menus should be dynamically spaced( SCGCQ00205520 ) 
 - Reduce nvdata settings needed to enable DDR	( SCGCQ00206430 ) 
 - Gen3 IR - Optimize SCSI Synchronize Cache command time intervals for reasonable overhead reduction.( SCGCQ00207726 ) 
 - Update IOP workaround code for B0 FPGA and silicon( SCGCQ00209592 ) 
 - ONFI: Fixes to ONFI code and enable ONFI interrupt( SCGCQ00213355 ) 
 - Customer requests header file changes( SCGCQ00217024 ) 
 - Add firmware support for SAS3004A0-1 and SAS3008A0-2	( SCGCQ00217468 ) 
 - PerfMon: L2/L3 Performance Monitoring( SCGCQ00223242 ) 
 - ONFI: Add UART commands for testing offload and restore	( SCGCQ00227317 ) 
 - Invader: Update DCR access functions to use indexed DCR instructions	( SCGCQ00234936 ) 
 - Add Ping utility to diag console	( SCGCQ00247670 ) 
 - add new iop onfi diag cmds for new onfi mirroring API functionality( SCGCQ00255174 ) 
 - (HW	( SCGCQ00260415 ) 
 - IOP Disable the idle interrupt( SCGCQ00286327 ) 
 - Merge header files to prevent overlap of definitions amongst WD, SBA and IR	( SCGCQ00295234 ) 
 - Changed SBR data so PCIe configuration data shows that the ASPM feature is not supported.( SCGCQ00307953 ) 
 - NVMe device asynchronous event handling( SCGCQ00334789 ) 
 - Add 4MB OCM support to FPGA	( SCGCQ00343319 ) 
 - (IOA	( SCGCQ00343530 ) 
 - Added new registers for new hardware	( SCGCQ00348166 ) 
 - (IOP	( SCGCQ00357214 ) 
 - Added code to dump IOA registers	( SCGCQ00383645 ) 
 - Enable Development Vehicle FPGA to use regular DDR3 library code path( SCGCQ00385238 ) 
 - More NVMe related changes( SCGCQ00390988 ) 
 - Add vendor unique DRAM device support( SCGCQ00391873 ) 
 - Backend PCIe: Allow de-configure and reconfigure of device memory chunk( SCGCQ00397609 ) 
 - Queue full handling for NVMe admin queue	( SCGCQ00399212 ) 
 - Tool change only, no change to FW( SCGCQ00400045 ) 
 - NVMe: Command timing during NVMe init( SCGCQ00417756 ) 
 - NVMe: command level error handling( SCGCQ00440187 ) 
 - NVMe: Native SGL validation mode	( SCGCQ00459734 ) 
 - More SOP IU Error handling( SCGCQ00464488 ) 
 - Dauntless SPI Flash Support	( SCGCQ00481295 ) 
 - ARM Port Build Options 2 - libraries, backtrace et al( SCGCQ00492621 ) 
 - Ventura: ARM M0+ RMC Image Support( SCGCQ00521623 ) 
 - Updated FxCore blocks to match new hardware( SCGCQ00522531 ) 
 - NVMe: task management, part 2( SCGCQ00525641 ) 
 - Enterprise: error message counter configuration( SCGCQ00552431 ) 
 - NVMe: Update translations to the latest version( SCGCQ00562270 ) 
 - PL: Add reserved U16 to PLI_RUNTIME_CONFIG( SCGCQ00609767 ) 
 - Intruder: update IOP Chip Feature list( SCGCQ00618689 ) 
 - clean out old IOP workaround that are no longer needed( SCGCQ00620254 ) 
 - Intruder: update CCR registers( SCGCQ00620515 ) 
 - Intruder FPGA updates for release 0.6 bitstream( SCGCQ00627879 ) 
 - Disable SAS1 interrupts in FW for 0.7 FPGA bitstream	( SCGCQ00632007 ) 
 - Updated header files for hardware names( SCGCQ00637211 ) 
 - Create suitable conversion functions between chipRelativePhyNum , coreRelativePhyNum and SasCoreNum	( SCGCQ00641789 ) 
 - Intruder: modify SAS Core base address and size, and update FW effective address map	( SCGCQ00661523 ) 
 - Backend PCI: add compile option for MSI(x( SCGCQ00668595 ) 
 - Intruder: Update plRemoveDevice to work with multiple SAS cores( SCGCQ00669830 ) 
 - Ventura: SPI library changes for integration with Methrat( SCGCQ00680520 ) 
 - Intruder: Update FPE completor error handling to support multicore( SCGCQ00684383 ) 
 - Intruder: Update the TLB entry for PCE Decode 3 - MU Registers( SCGCQ00686770 ) 
 - Ventura: backend PCIe: revise devhandle macros( SCGCQ00690231 ) 
 - Fix access to initiator table for Target Mode( SCGCQ00716824 ) 
 - Cleanup of #if INVADER	( SCGCQ00728719 ) 
 - Ventura: PL Dual/Multiple CPU Queue Task Management Support	( SCGCQ00754472 ) 
 - Ventura: Initial Cache Snooping Settings	( SCGCQ00759738 ) 
 - Ventura: Create Official MR Build Release Scripts( SCGCQ00760495 ) 
 - Ventura: Enterprise: return unique status for CRS on config space access	( SCGCQ00761092 ) 
 - Ventura: Add support for PCIe Topo Change List Event PORT_CHANGED status	( SCGCQ00771836 ) 
 - pl: AHCI: add check for 64 bit addressing support	( SCGCQ00776856 ) 
 - Ventura: Update ARM DS-5 to version 5.19.1( SCGCQ00778839 ) 
 - SAS3.5 iopBootLoader.c needs to be updated with Intruder values	( SCGCQ00807720 ) 
 - Remove Manufacturing Page 8 Definitions	( SCGCQ00814364 ) 
 - Implement memory burst mechanism for Ventura MSS	( SCGCQ00814469 ) 
 - Ventura: MSS - Write per-bit deskew training algorithm	( SCGCQ00814801 ) 
 - Aladin Core: Support Fast Trace Data Collection via UART	( SCGCQ00816086 ) 
 - SAS3.5 Create Flash Scripts for Cutlass	( SCGCQ00819460 ) 
 - Tiger: Update num of Phys per chip usage to account for remote SEDs - Part 1	( SCGCQ00823845 ) 
 - Integrate Guinness CSW Hardware Include Files( SCGCQ00827425 ) 
 - IOP: Add support for fan controllers over I2C( SCGCQ00833807 ) 
 - Ventura: Integrate MPI2.6 2.00.37 header files( SCGCQ00837256 ) 
 - SAS9305-16i Partial NVDATA	( SCGCQ00845398 ) 
 - Update RBD tool to support addition of "TraceSource" field in buffer entries.( SCGCQ00850240 ) 
 - Add GHS ARM compiler type to the CommonSerdes library makefile( SCGCQ00864342 ) 
 - Ventura MSS: Miscellaneous Interface Changes( SCGCQ00865201 ) 
 - Ventura: add Dword pad to SBRImage( SCGCQ00880161 ) 
 - Ventura: Modify VENTURA_PORTING	( SCGCQ00883658 ) 
 - Ventura: Additional Modifications For Host Boot Compatibility( SCGCQ00891598 ) 
 - Update Sbus address values( SCGCQ00894722 ) 
 - Removed Dauntless platform specific code from the backend PCI PL code base( SCGCQ00905990 ) 
 - Ventura: Cache MMU tables to increase performance( SCGCQ00906058 ) 
 - Ventura: Add compile option to enable/disable AHCI Support( SCGCQ00908659 ) 
 - IOP: Update loader for Tiger hardware( SCGCQ00910342 ) 
 - Add PIM/POM table entries for Tiger/Styker( SCGCQ00910622 ) 
 - Ventura: Update fwheadx.exe utility to recognize new devices	( SCGCQ00910696 ) 
 - Ventura: Update to latest MPI headers( SCGCQ00911517 ) 
 - IOP: Tiger/Stryker convert to use ARM Vectored Interrupt Controller( SCGCQ00917849 ) 
 - Ventura: Enable exclusive access instructions for synchronization( SCGCQ00927387 ) 
 - Ventura: Add partial image support to boot loader for MR Host Boot support( SCGCQ00929582 ) 
 - Cleanup some I2C address #defines( SCGCQ00930647 ) 
 - PL: Add handling of inbound SAS Topology Change List Events( SCGCQ00939823 ) 
 - Tiger: Implement MSIx Interrupt Handler for handling CSR	( SCGCQ00940370 ) 
 - Tiger: Add Pex HW related uart commands	( SCGCQ00940378 ) 
 - Allow library to be built within sub projects( SCGCQ00943057 ) 
 - Ventura: Create Harpoon (8-phy	( SCGCQ00949178 ) 
 - Ventura: Add support for "iop reset" CLI command	( SCGCQ00953786 ) 
 - Build all cleanup( SCGCQ00983745 ) 
 - Ventura: Create Partial XML file to disable backend PCIe/NVMe	( SCGCQ00996248 ) 
 - Tiger: Handle Host Link Down-Up	( SCGCQ00997588 ) 
 - Ventura: Allow Gen 3 host side connection	( SCGCQ01003672 ) 
 - Tiger Ventura: Renumber some Fault codes to clear out a distinct range for Ventura faults from MPI devices( SCGCQ01020521 ) 
 - Tiger IOP: Enable SR-IOV mode by default to allow multi-path	( SCGCQ01023850 ) 
 - Tiger FPGA: Implement Abort Task Set, LUN Reset and Clear Task Set to SED attached End devices( SCGCQ01024838 ) 
 - Ventura: Add non-production SRIOV build	( SCGCQ01035200 ) 
 - Ventura B0 default DMA Q masking settings( SCGCQ01082715 ) 
 - Update Tx EQ settings to recommended default values( SCGCQ01088723 ) 
 - Aero: Update IOP and libraries for new compiler	( SCGCQ01095747 ) 
 - AERO: Boot Loader Changes to get past IopStartOfDay( SCGCQ01127748 ) 
 - PLI: Add PL fault codes to doxygen generated PLI documentation( SCGCQ01154129 ) 
 - 9405W-16e NVdata file - Add to SAS 3.5 Phase 3	( SCGCQ01238957 ) 
 - Ventura/Marlin: backend PCIe: SRNS( SCGCQ01273153 ) 
 - Shut off Fast Path Engine more quickly when Faulting the controller( SCGCQ01353459 ) 
 -	( SCGCQ01355029 ) 
 - Warning removal 188	( SCGCQ01365171 ) 
 - Warning removal 1295	( SCGCQ01365178 ) 
 - FLR: Load pce hw settings when FLR happens.	( SCGCQ01382722 ) 
 - BST script for JBOD personality	( SCGCQ01389661 ) 
 - SCons armv5 build server support	( SCGCQ01393685 ) 
 - Improvements to Avenger build tools	( SCGCQ01400119 ) 
 - Handling EPD error recovery for Host Dcdb's in JBOD personality( SCGCQ01400587 ) 
 - Add new ISSI SPI flash as a supported part. (IS25WP256D-RHLE	( SCGCQ01412646 ) 
 - Fine tune block thresholds for slow arrays( SCGCQ01418141 ) 
 - Move ECC handling to OCM from DDR( SCGCQ01440110 ) 
 - Support additional dynamic sections in NVRAM	( SCGCQ01440146 ) 
 - Integrate MR PL-SCS Libs: SASFW_Ventura_Phase_5.0 04.250.09.00( SCGCQ01442972 ) 
 - pl: NVMe: NVMe task management modifications (part 2	( SCGCQ01445903 ) 
 - (SATA Only	( SCGCQ01454125 ) 
 - enable OOB FW download for MR alone.	( SCGCQ01455694 ) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_5.0 - 05.25.01.00 MR PL-SCS Libs( SCGCQ01455809 ) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_4.0 - 04.25.04.00 MR PL-SCS Libs( SCGCQ01462721 ) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_5.0 - 05.25.02.00 MR PL-SCS Libs( SCGCQ01464185 ) 
 - Make NVRAM changes to support Transport Ready( SCGCQ01464212 ) 
 - Support for disabling personality modes	( SCGCQ01464952 ) 
 - UNMAP support blocked on a OEM( SCGCQ01466783 ) 
 - Disallow mixture of NVMe drives and SAS/SATA drives in VD creation( SCGCQ01474267 ) 
 - Use the latest PL version 5.250.5.0	( SCGCQ01508530 ) 
 - Ethernet: Firmware Download using TFTP( SCGCQ00114825 ) 
 - Update L2cache.h	( SCGCQ00129837 ) 
 - DDR3 improvements based on internal customer feedback( SCGCQ00136650 ) 
 - Request for modification of default Mustang/Tbolt NVData to enable PCE ROM Bar (PCE Mem Bar 2( SCGCQ00138033 ) 
 - IR’s port to MPI v2.5( SCGCQ00140190 ) 
 - IOP/Boot Loader: Update initialization and boot loader assembly language code for PPC476.( SCGCQ00144376 ) 
 - Gen3 PwrMgmt: Update config page handler for IO Unit Page 7( SCGCQ00146802 ) 
 - Code cleanup and bug fixes for adding entries to Colt's TxDMAQ( SCGCQ00149115 ) 
 - Update MPI version information returned by the controller( SCGCQ00150073 ) 
 - pl: Detect if a device supports Download Microcode DMA	( SCGCQ00152237 ) 
 - Set the lower two bits of the context address correctly when messing with non-passthru dma entries( SCGCQ00155499 ) 
 - Custom NVDATA values for IR3	( SCGCQ00155852 ) 
 - Modify DDR3 ECC atomic scrub	( SCGCQ00170497 ) 
 - CLI Support reading and writing "physical 64 bit" memory	( SCGCQ00170518 ) 
 - Update TLB Dump CLI utility for Gen 3	( SCGCQ00172590 ) 
 - MPI2: Add IO Unit Page 10 - Host Credit Balancing	( SCGCQ00175997 ) 
 - RMTFLASH updates for silicon	( SCGCQ00185741 ) 
 - Gen3: Update temperature conversion equation as per LSI c temperature sensor for Invader	( SCGCQ00188118 ) 
 - Integrate L3 into OCM memory region	( SCGCQ00189083 ) 
 - Update romimage utility to handle larger image sizes	( SCGCQ00189755 ) 
 - Gen3: LTRACE support	( SCGCQ00193396 ) 
 - Change to DDR3 Library Interface	( SCGCQ00201057 ) 
 - Implement function that clears cached memory to zero efficiently	( SCGCQ00202447 ) 
 - Increase the frequency of the fast DCR clock to 500 MHz	( SCGCQ00206592 ) 
 - Overhaul read fifo algorithm for Invader	( SCGCQ00227345 ) 
 - Change OR retry *time* values to 1uSec (or whatever is lowest possible( SCGCQ00228191 ) 
 - Interface change to DDR3 library in order to utilize modified read fifo algorithm( SCGCQ00228961 ) 
 - pl pci: NVMe Initialization	( SCGCQ00276500 ) 
 - pl: NVMe SCSI IO Path( SCGCQ00308842 ) 
 - pl: NVMe Stang Initialization( SCGCQ00336344 ) 
 - (IOA	( SCGCQ00348944 ) 
 - pl pci: Discovery and Device Manager	( SCGCQ00352772 ) 
 - NVMe glue code( SCGCQ00357921 ) 
 - Add PCIe ID of A0( SCGCQ00369164 ) 
 - DDR3 - Update for Development Vehicle Support	( SCGCQ00385350 ) 
 - Update existing backend PCIe events to MPI-2.6 format( SCGCQ00391416 ) 
 - NVMe: Check in init workarounds for early NVMe device( SCGCQ00450246 ) 
 - Create new build environment for future product	( SCGCQ00477789 ) 
 - Update PQI and SOP to the latest revisions	( SCGCQ00502916 ) 
 - Add Mfg Pg 30 field for max SASCore exceptions per interrupt	( SCGCQ00525637 ) 
 - Ventura: Modify Ventura FLASH Layout to comply to new MPI2 regions	( SCGCQ00622860 ) 
 - Update IOCInit and IOCFacts handling for MPI 2.6	( SCGCQ00634123 ) 
 - Modify NVDATA to configure the port numbers for phys on FPGA	( SCGCQ00667559 ) 
 - Enterprise: additional preparation for device INTx support( SCGCQ00668628 ) 
 - Intruder FPGA Release 2.0 interrupt map	( SCGCQ00681295 ) 
 - Ventura: Create Release ANSI builds for Validation	( SCGCQ00682063 ) 
 - Ventura: Create a separate directory for MPI files in library releases( SCGCQ00684275 ) 
 - Ventura: Update FIrmware Upload and Download for MPI 2.6	( SCGCQ00741847 ) 
 - FW Controlled Spinup: Periodic NOTIFY (ENABLE SPINUP	( SCGCQ00757326 ) 
 - Ventura: Implement backrace symbol output( SCGCQ00759726 ) 
 - Ventura: Update PDB Performance Monitoring( SCGCQ00773033 ) 
 - Ventura: MSS - Build system update and various minor bug fixes( SCGCQ00787018 ) 
 - Ventura: Ensure all OCM initialization uses 8-byte writes( SCGCQ00806159 ) 
 - Ventura: MSS - Atomic ECC scrub functionality( SCGCQ00817281 ) 
 - Ventura: Add DDR Library To MR Release Package & Change PL to include PCI( SCGCQ00822637 ) 
 - Ventura: IOP - Finish IT Firmware integration with MSS library( SCGCQ00829569 ) 
 - Miscellaneous RMC AI	( SCGCQ00911441 ) 
 - Ventura: update sbrimage to skip an image( SCGCQ00916884 ) 
 - TigerStryker: (IOP( SCGCQ00929151 ) 
 - Tiger IOP: Update clock divider function	( SCGCQ00987123 ) 
 - Changes needed in IT Fimrware to implement a StorCLI functionality( SCGCQ01037129 ) 
 - Ventura MSS: Add debug prints indicating width of read leveling data eye for each data lane( SCGCQ01049394 ) 
 - Warning removal 186	( SCGCQ01365170 ) 
 - JBOD profile 20 with 240VD/PD. Make profile 20 work as 240Pds.( SCGCQ01373083 ) 
 - pl: NVMe: add translation for PRP Offset Invalid error	( SCGCQ01378850 ) 
 - Add site license warning suppression	( SCGCQ01416563 ) 
 - Removed two debug print statements.	( SCGCQ01429843 ) 
 - MR7.4 Talla 16i NVMe: (Intermittent	( SCGCQ01430608 ) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_5.0 - 05.25.00.00 MR PL-SCS Libs( SCGCQ01449472 ) 
 - Ventura/Marlin: Change to ARM site licenses( SCGCQ01461714 ) 
 -	( SCGCQ01473957 ) 
 -	( SCGCQ01511868 ) 
 - USB stack library for Thunderbolt platform( SCGCQ00135528 ) 
 - Gen3: L3 Cache Controller support( SCGCQ00140714 ) 
 - Support Elektra's BIST functionality	( SCGCQ00154745 ) 
 - Second set of DDR3 changes for Elektra/Invader( SCGCQ00160620 ) 
 - Update move to and from DCR GCC assembly language macros	( SCGCQ00166717 ) 
 - IOP : Atomic ECC Scrub support( SCGCQ00170052 ) 
 - Gen3 IR: C_IR::SetFastPath( SCGCQ00200491 ) 
 - ONFI: Add UART command for bad block list creation( SCGCQ00215351 ) 
 - Add more #defines for the CCR0 register in ppc476.h( SCGCQ00223487 ) 
 - When a fault occurs, send SAS BROADCAST(RESERVE 4( SCGCQ00229102 ) 
 - Invader B0 temperature sensor coefficients must be updated( SCGCQ00317514 ) 
 - PCIe Interrupt Changes( SCGCQ00340457 ) 
 - NVMe: Read/write IO breakup for PRP format SGLs( SCGCQ00415503 ) 
 - SOP/PQI Device Initialization and base IO support( SCGCQ00426938 ) 
 - Change SASIoUnitControl to IoUnitControl for Dauntless sources( SCGCQ00456975 ) 
 - No check for good status in pliFpeGeneralErrorInterrupt(	( SCGCQ00490961 ) 
 - Develope Boot Loader Build Process for ARM( SCGCQ00571692 ) 
 - Ventura: MSS - Initial ARM library build creation and interface check build creation	( SCGCQ00635808 ) 
 - Ventura: RMC add support for AVSO programming( SCGCQ00822255 ) 
 - Ventura: backend PCIe: add support for not faulting on resource setup failure( SCGCQ00928542 ) 
 - Ventura: Support csw library both without and without debug symbols.	( SCGCQ00931577 ) 
 - IOP: Create Tiger workaround definition	( SCGCQ01002513 ) 
 - JBOD_Personality : Base EPD management changes( SCGCQ01301492 ) 
 - Implement Array Based Cache Block Threhsolds	( SCGCQ01316715 ) 
 - Warning removal 68( SCGCQ01365167 ) 
 -	( SCGCQ01378116 ) 
 - Implement HW Change Request: Need workaround for PCIe expansion BAR issue implemented in MegaRAID( SCGCQ01382712 ) 
 - Store the RAID SubDevID in NVRAM to have a reference to original RAID-ID.( SCGCQ01385845 ) 
 - Cache headers, bsb_headers were not rearranged after the pre-boot memory is released.( SCGCQ01397554 ) 
 -	( SCGCQ01419068 ) 
 - Avenger: Change symbol build tool from external executable to internal python( SCGCQ01494130 ) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_6.0 - 05.250.04.00 MR PL-SCS Libs	( SCGCQ01494509 ) 
 - Updates for Trident EDS 1.02	( SCGCQ00173281 ) 
 - FPE trace buffer prints for PCIe devices	( SCGCQ00394555 ) 
 - (ARM BUILD	( SCGCQ00552099 ) 
 - SAS3.5 Create new NvData Schema that separate channel and OEM NvData	( SCGCQ00807520 ) 
 - Warning removal 177	( SCGCQ01365169 ) 
 - Handle FLR when OCR is disabled	( SCGCQ01389611 ) 
 -	( SCGCQ01464963 ) 
 - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_6.0 - 05.250.01.00 MR PL-SCS Libs( SCGCQ01474311 ) 
 - Make DDR3 support optional( SCGCQ00143542 ) 
 - Warning removal 1254	( SCGCQ01365176 ) 
 -	( SCGCQ01382765 ) 
 - Perform the F/W Upgrade and downgrade.( SCGCQ01385051 ) 
 - Define SBR bits to control UART speed( SCGCQ01465004 ) 
 - Agni (PBAM	( SCGCQ00342465 ) 
 -( SCGCQ01384070 ) 

	

Version 50.3.0-1075- Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:  7.03.02.0
	UEFI Driver: 0x07030400
	HII:  07.03.11.00
	MR FW:  5.030.00-1232
	PACKAGE:  50.3.0-1075
fixes:
-1901 Fault due to a Port open fail interrupt without a matching transport error.(SCGCQ00136195)
-Thunderbolt B0: Implement workaround from BT1682(SCGCQ00138062)
-Change hardcoded fault code to a properly defined code.(SCGCQ00141606
-Calculation of pl memory may be bigger than necessary for some regions.(SCGCQ00141622 )
-fault 0x5893(SCGCQ00142708)
-SAS Device Page 1 data for first drive or single drive was all zero(SCGCQ00144104 )
-Fix SMP passthrough immediate mode(SCGCQ00144357)
-pl fpe diag command (mgrds) shows too little data(SCGCQ00144379)
-x5891 Fault After OPEN Timeout(SCGCQ00145434)
- Converting SATA Standby count to proper Standby condition timer value in Power condition mode page (page 0x1a) for mode sense command.(SCGCQ00145610) 
 -FPGA: Gen3 TaskMgmt: 0x265D Fault When Processing Multiple TARGET RESET TMs(SCGCQ00145645)
-Correction to Diagnostic Code to Show PL Memory Details(SCGCQ00145990)
 -PL Library wouldn't link due to missing plmath.o(SCGCQ00146017 )
 -B-T1680: 6001 fault(SCGCQ00146564)
 -FPGA: Gen3 TaskMgmt: 0x5110 Fault on Overlapped TARGET RESETs to SATA devices(SCGCQ00146626)
 -Fix 6202 fault when sending I/Os to a SATA drive(SCGCQ00146780)
 -PL Lib build fails(SCGCQ00146819)
 -Expander goes missing during Expander phy reset testing.(SCGCQ00146846)
 -FW hangs when sending sense data back to the host for a sata I/O(SCGCQ00146936)
 -ON_TASK_MANAGEMENT_INACTIVE Notification Not Being Sent To CudaMgr(SCGCQ00146956)
 -FPGA: Gen3 TaskMgmt: Internal Memory Corruption Causes 0x6825 Fault During LUN RESET(SCGCQ00146965)
 -Enable Requestor/completor after port enable completes instead of waiting for associated discovery to complete.(SCGCQ00148644)
 -Fault 6004 on a target reset TM to an expander attached SAS drive running FP IOs(SCGCQ00149004)
 -(Sata Only): Non auto SCSI command to a fast path enabled SATA drive times out.(SCGCQ00150032)
 -TBM: Normal mode entries are missing after pliStartOfDay(SCGCQ00150202)
 -(Sata Only): Fault 0x265D on sending Read(16) with LBA greater than 48 bit(SCGCQ00151324)
 -SSP Error Handler function chokes on Fast Path IO error handling(SCGCQ00151377) 
 -TM completion handler incorrectly clears midused for Fast Path IOs(SCGCQ00151378)
 -Fpe Manager has required code optimized out.(SCGCQ00151836)
 -Disable CmdAnalyzerStateTimer for FPGA(SCGCQ00153845)
 -wrong ComponentId values used to identify Cobra expander(SCGCQ00154786 )
 -RequestLength field not set in the SMP Report EDFB Settings requests(SCGCQ00155258)
 -TBM: TLB Fault while reading trace entry(SCGCQ00155579 )
 -NA(SCGCQ00155582)
 -PL library linkerr error(SCGCQ00156105 )
 -Discovery leads to FW Fault 0xD072(SCGCQ00156488)
 -FPGA: Task Management on Invader may cause a 6002 Fault(SCGCQ00157799)
 -FPE: Aborttask UART command to handle FPE IOs does not work.(SCGCQ00157806) 
 -PL Lib build fix(SCGCQ00158324)
 -SATA FPE IOs get stuck(SCGCQ00158983 )
 -FPGA: TxDma fails to send data after receiving an xfer_rdy from the target(SCGCQ00159121)
 -Fixed 0x265D fault generated by with execution of command "pl reg *".(SCGCQ00159371)
 -TM completes successfully even after invoking a timeout(SCGCQ00159958) 
 -Debug tracking value was not correctly reset on PL(SCGCQ00160504)
 -SEP devices marked as Fast Path Capable(SCGCQ00160703 )
 -FPE: Fault 6003 Occurs during Jammer script testing(SCGCQ00160884) 
 -Fault 0x265D occurs when receiving an Invalid MID (Jammer Test Case)(SCGCQ00162468) 
 -FPE- fix print statement in the frame ownership function (SCGCQ00162942)
 -Get the formatting/alignment of columns to match up.(SCGCQ00163733)
 -FPE: Dev handle corruption while posting IOs to Cuda's IOPStartQueue(SCGCQ00163840)
 -FPGA: Handling I/Os In Target Mode results in a fault 0x5120.(SCGCQ00165393 )
 -FPGA: FPE: 0xD063 fault while running fast path IOs(SCGCQ00167839)
 -FPE fault D094(SCGCQ00167842 )
 -Fpe exception queue interrupt handling does not update queue if an entry is invalid(SCGCQ00168593)
 -(PL) Missing Not Responding and Device Added Events on Device Move(SCGCQ00169455)
 -Fault 4203 while hot(SCGCQ00170048 )
 -PL is faulting with fault code 0xd075 when an IO times out(SCGCQ00170147)
 -SATA I/O timeout while loading OS drivers(SCGCQ00170253) 
 -reading trace buffer adds trace entries(SCGCQ00170305)
 -0xD071 Fault when running TM's to SATA drives(SCGCQ00170551 )
 -FPGA: 5894 fault during stress and Random Expander Phy power downs(SCGCQ00171100)
 -Fast Path Timer errors not seen after intial timer error(SCGCQ00172024 )
 -Fault 0x5111 while sending random TMs to Random SATA Targets every 5 to 8 seconds(SCGCQ00172122)
 -Verification discovered scenario where 2 identical OPEN requests may come from SASCore for same device/IO(SCGCQ00172541)
 -Fault D091 with Destructive Domain Validation Test.(SCGCQ00173093)
 -FPGA: IOs fail while doing Target mode TM testing (SCGCQ00174516)
 -difficult to change SATA NCQ option on a device(SCGCQ00174545)
 -ReadBuf Command hangs(SCGCQ00174555)
 -Confusing prints in task management code(SCGCQ00177300 )
 -FPGA: IOs fail during Target Mode SSP TM tests(SCGCQ00177626)
 -D110 fault while doing Block Move test(SCGCQ00181603 )
 -Fault 670A with Block Move Test and Powercycling Enclosures(SCGCQ00181751 )
 -write buffer command (via a sata passthrough request) during stress causes the adapter to reset.(SCGCQ00181783)
 -FPGA: Hw pending Ios not started after IO completion(SCGCQ00184075)
 -Build all fails with error(SCGCQ00184424 )
 -Task Management code slowing down IO path(SCGCQ00184744)
 -FPGA: Fault 0x265D while running IO and powercycling Enclosures(SCGCQ00184892)
 -Phy power code is using the wrong mask(SCGCQ00186364)
 -Initialization of DMAGroup in txctxmgrs is wrong for non(SCGCQ00186661)
 -Power management init code needs to be called before phy init(SCGCQ00186691 )
 -TBM Recursive Fault(SCGCQ00187763 )
 -Controller faults with code 5891 while running task management tests(SCGCQ00187778 )
 -Controller faults with code 6003 while running task management tests(SCGCQ00187962)
 -FPGA: After IO Timeout and TAsk Management IO stops and UART hangs(SCGCQ00188093)
 -Debug print was mis(SCGCQ00188926)
 -PL Lib No DEBUG build wasn't compiling(SCGCQ00189379 )
 -Multiple Timers could be added for single IO(SCGCQ00189781)
 -Running I/Os to SATA HDDs w/Jammer scripts results in fault 0x265D(SCGCQ00189790)
 -Gen3: A Jammer script sends too much data for a Read command which results in SysDmaParity fault.(SCGCQ00190412)
 -Fault 0xD071 while doing message unit reset(SCGCQ00190417)
 -After NCQ error recovery, device QDepth is not being restored.(SCGCQ00190925)
 -Fixe pl.h compile when ENABLE_TRACEBUFFER_MANAGER is not on(SCGCQ00190928 )
 -IO count mismatch while handling Task Set Full event in firmware(SCGCQ00192194)
 -Gen3 PwrMgmt: Update shared global Pwr Mgmt structures.(SCGCQ00192501)
 -SATA 4k sector size will not start IO.(SCGCQ00193363)
 -Invader A0: Fault 0xD027 while running Medusa Pain Stress Tool in Windows 2008 R2(SCGCQ00194013)
 -Sending HARD RESET to target while under I/O load results in 6001 IOP fault(SCGCQ00194139)
 -Firmware repeatedly sending a event whenever it get a spinup notify causes target mode initialization to stall(SCGCQ00194444 )
 -SATA write I/Os timeout especially behind expander(SCGCQ00194464)
 -FPE Status values passed to iopiFPEHandleException() weren't included in PLI release(SCGCQ00194558)
 -Gen3 PwrMgmt: Tx/Rx DMA Memory faults 0x6B72 when exiting shutdown mode(SCGCQ00194688)
 -Gen3 PwrMgmt: Unexpected event is sent when changing Direct Attached HDD Pwr states.(SCGCQ00194919)
 -Invalid Loginfo value seen when a Wrong Relative Offset error encountered on transmit data path(SCGCQ00194925)
 -IO Timeouts/0x6001 fault during SATA TM Read Mayhem test(SCGCQ00195557)
 -Sata Targets are never initialized(SCGCQ00197633)
 -fault d012 with stress fast path IOs on a single drive (SCGCQ00199529)
 -Invader A0: D072 Fault during stress and whole port glitches(SCGCQ00200261)
 -Fault 0x26B1(SCGCQ00200380 )
 -Gen3 PwrMgmt: Open Address frame has a SAS Address of zero when a device wakes up from PM.(SCGCQ00200472_
 -Gen3PwrMgmt: PM status interrupt fires intermittently.(SCGCQ00200477)
 -Fault 0x5805(SCGCQ00200637)
 -Invader A0: 5893 Fault when the whole port (between enclosures) is broken during stress.(SCGCQ00200645)
 -TM causes 0xD072 fault if a TM fails to clean IOs on a Target Reset(SCGCQ00200652)
 -When direct attached entities are disconnected from Invader phys, occasionally phys don't show link down.(SCGCQ00202367)
 -IOs timeout when running task management tests(SCGCQ00203055
 -IO timeout to SATA target behind expander.(SCGCQ00203063)
 -Try running firmware with Fast Path engine Dyno mode enabled, observe drives don't really show up correctly ((SCGCQ00203659)
 -Compile option for to PL setup the SASCore to use alternate PLB segement for memory access was incorrect(SCGCQ00204613)
 -Invader A0 (init/targ): 0x7c54 fault during stress and cable breaks(SCGCQ00205569 )
 -IOCount for DevHandle 0x00 is incremented during FPE hardware pend queue cleanup(SCGCQ00205960)
 -Update compile option sets SASCore to use alternate PLB segment for context access to work on FPE CompQ(SCGCQ00207017)
 -Invader A0: D072 fault during Block Move test(SCGCQ00207153)
 -(SCGCQ00207699)
 -BIOS banner spin up delay issue (w/SATA drives)SCGCQ00208198)
 -Fault 0xD100 when sending SATA PassThrough IO(SCGCQ00208413)
 -A0: Firmware not clearing TM Completion Mid flag correctly(SCGCQ00209005)
 -Direct attached SEP device did not get discovered properly.(SCGCQ00209485)
 -Invader A0: All devices go missing when the link between the first two expanders is broken(SCGCQ00210025)
 -Bursty SAS write I/O when running with SATA format cmd(SCGCQ00210166)
 -Non Target build still had a target only function(SCGCQ00210482
 -For Target mode when performing send status with data the call to iopiMemoryMove() doesn't reflect the correct address space.(SCGCQ00213224)
 -Invader A0: Fault 6708 when loading the Linux Driver to Cascaded Enclosure Topology(SCGCQ00215422 )
 -Invader A0: Fault D060 while running Block Move and Task Management Test in CM(SCGCQ00215835)
 -Fault 0x5881(SCGCQ00215843 )
 -B0 FPGA: Pl faults with fault code 0x5842 during MR FW boot up.(SCGCQ00216384)
 -Gen3: FPGA validation of B0 fails with 0x6109(SCGCQ00217020 )
 -Snooping configuration not set on SAS Core DMA PLB Master(SCGCQ00218116 )
 -Failures connecting to SATA drives or expander attached disks(SCGCQ00218117)
 -SATA IO timeouts after NCQ error handling (SCGCQ00218797 )
 -Fault 0x6001 after IO timeouts(SCGCQ00219558)
 -SATA Passthrough Message to Non(SCGCQ00219819)
 -Discovery fails with SMP timeout while cable pull push in a multipath topology(SCGCQ00221089)
 -Invader A0: 0x5002 on Target when disabling then reenabling Phy(SCGCQ00223630)
 -Invader A0: Data Corruption/Miscompare when changing Global Power Management via MPI Requests(SCGCQ00224120)
 -Fault 0x4A00(SCGCQ00224173)
 -Fault 5845 seen when running IO with cable glitching(SCGCQ00224215)
 -Firmware displayed wrong version number(SCGCQ00225971 )
 -Invadr A0: Add new software flag to store IO messaging mode(SCGCQ00226340)
 -Fault 0x610B seen when doing Task management(SCGCQ00226699)
 -0x61A3 fault during task management(SCGCQ00226954)
 -Fault 0x5302 when running IO and using Close Clear Affiliation option(SCGCQ00227563)
 -Invader A0: Fault x5842 with running Block Move and Task Management Test(SCGCQ00227896 )
 -Fault x5900 seen running heavy IO with discovery(SCGCQ00228216)
 -System hangs or reboots, or Fault x5863(SCGCQ00228819)
 -Large write IO timeout(SCGCQ00228945 )
 -Drives lost due to HW interrup not cleared correctly (RX Context Manager Timer Reached)(SCGCQ00229130)
 -Fault 0x4203 during Reconstruction on SATA drives(SCGCQ00229646)
 -Slow performance of non automated IOs issued to SATA drives(SCGCQ00230305)
 -Invader A0: 0x583B fault during IO and Task Management in CM(SCGCQ00230354 )
 -Add flush write to ensure the pause goes to FPE immediately,(SCGCQ00230498 )
 -SMP Passthru requests from host not completing when expected reponse length is set to 1.(SCGCQ00231734)
 -Fault 0x5842 occurs when cable break/glitching done running IO(SCGCQ00232016)
 -Gen3: PwrMgmt (SCGCQ00233745)
- Invader: Fault 0x5831 occurs after PL register dump(SCGCQ00235412)
 -Fault 0x510B(SCGCQ00237408)
 -Fault 510b during enclosure pull push.(SCGCQ00237445)
 -Fault 0x5304 during enclosure pull push(SCGCQ00237446)
 -Invader A0: 0x5894 during IO Stress and 5ms Whole Port Glitches(SCGCQ00238962)
 -IO timeouts while running stress loads on a mix of SAS and SATA drives(SCGCQ00239369 )
 -Large IO size to mixed SAS/SATA causing errors(SCGCQ00242618)
 -PL Fault 0x670C(SCGCQ00243099)
 -Gen3 : Build failing for the latest tipcode when build all command is issued.(SCGCQ00246801)
 -Fault d062 while running IOs on SATA drives with medium errors(SCGCQ00247456 )
 -Fault 0x583E(SCGCQ00247837)
 -Discovery error x90 while running IOs on a mix of SAS and SATA drives.(SCGCQ00249597)
 -Fault 6708 seen running cable break/glithes(SCGCQ00250218)
 -Discovery error with status 0x10 during enclosure pull/push cycles(SCGCQ00250817 )
 -Invader A0: Update needed for RAID Context usage(SCGCQ00251530)
 -Discovery fails to complete in 120s with chained enclosures(SCGCQ00251979)
 -Linking PL library with non(SCGCQ00253272)
 -Dependency on GHS library for 64 bit multiplication (SCGCQ00253316)
 -Clean up depriciated device manager functions plDeviceManagerSetMissing(SCGCQ00255210 )
 -Trace buffer may be missing last chunk, up to 16k.(SCGCQ00255895)
 -Power settings request will fail to SATA drive that has powere mode enabled.(SCGCQ00256725 )
 -On fault, some final part of the Ring buffer may not be present in the trace buffer.(SCGCQ00257652)
 -Fault 0x58B4 when trying to run on a 4port controller(SCGCQ00258518)
 -PL Debug string PL_DBG_STR_CONTROLQ_DISABLE_HANG needs to be fixed so a print does not show up as ??SCGCQ00258558)
 -Move FPE and TBM global bits out of PL_INFO_FLAGS and into the FPE_INFO and TBM_INFO fieldsSCGCQ00258992)
 -Fault 0x5849(SCGCQ00259195)
 -Invader A0: (PL) Activate FPE after TM completes is getting initialized incorrectly in PL(SCGCQ00259546)
 -Gen 3 : Affilation conflict and the SATA drive connected beyond the expander will not be detected(SCGCQ00259968)
 -Data corruption seen during TLR(SCGCQ00260533)
 -Invader A0: (PL-Target Mode) Target Assist reply not being sent for EEDP apptag error(SCGCQ00261585)
 -Fixed name of local variable(SCGCQ00261861 ))
 -Code analysis tool defects resolution(SCGCQ00263862)
 -PL fault 0xd074 processing the same FPE Completor Error (Timer) twice(SCGCQ00264889)
 -PL was making call to IOP layer config read function for a READ_CURRENT of PL owned page before Port Enable completes(SCGCQ00266032)
 -pldebug.h file is not included in current PL lib releases(SCGCQ00276224)
 -Controller keeps resetting a SATA drive if the drive is security locked(SCGCQ00276277 )
 -Fault D099(SCGCQ00276477)
 -Fault x6108 seen when running IO and having TM occur(SCGCQ00277552)
 -Fault 0x6414 (SCGCQ00278271)
 -Fault x584B running Task managements with cable glitching(SCGCQ00278809 )
 -Invader B0: Implement hardware workaround for setting TLR bit properly.(SCGCQ00279492)
 -Fault 0x6414 Hot Plugging a Direct Attach Device(SCGCQ00279649)
 -A debug print needs Link # added to be more useful(SCGCQ00279991)
 -Invader B0: Firmware not sending Close (Clear Affiliation) to SATA drive(SCGCQ00280557 )
 -A hardware workaround was incorrectly disabled for B0(SCGCQ00280738)
 -Invader B0: 6003 fault while running SSP_INIT_Normal_List group of jammer scripts(SCGCQ00280742)
 -PL: receive path stalls result in SMP timeouts(SCGCQ00281960)
 -fault 5821 while running IOs on SATA drives (with DEBUG disabled)(SCGCQ00282860)
 -Gen3(SCGCQ00282874)
 -Invader B0: During whole port glitches while running i/o, hit D079 fault.(SCGCQ00282946)
 -Invader B0: Fault x5894 durning I/T switching during IO(SCGCQ00283484)
 -Help for CLI command "pl pm ps" not adequate(SCGCQ00283534)
 -Sata Translation I/Os will fail or cause 583C fault.(SCGCQ00284574)
 -Invader B0: Fault 0x5896 while Powercycling Random Enclosures(SCGCQ00284582 )
 -Invader B0: Continuous async events and Cuda pause while running IOs on SATA(SCGCQ00285056)
 -Fixed source level debugging using GHS probe.(SCGCQ00286179)
 -Fault d075 (SCGCQ00286703)
 -Invader B0: D074 fault occurs during simple IO stress when Fastpath timeout is set to the minimum value (1 second)(SCGCQ00286838)
 -Invader B0: FPE Manager Fault code cleanup and documenation update(SCGCQ00286906) 
 -Fast Path hardware Auto Pend and Completion events don't work.(SCGCQ00287160)
-Phy page 0 may report incorrect information of the current phy(SCGCQ00289533)
 -power management mode.(SCGCQ00290665)
 -An IO may incorrectly be aborted with loginfo PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED when it has been sent(SCGCQ00291818 )
 -Initiator behavior in dropped ACK/NACK to SSP Command frame compliance test(SCGCQ00292021)
 -Fault x5801 seen running IO with Task management(SCGCQ00292512)
 -Invader B0: SATA Passthrough occasionally time out during Heavy IO(SCGCQ00292639)
 -Volume removal resets the controller for further operations.(SCGCQ00292814)
 -Invader faults with 0x7C39 when sending Security Protocol Out Disable Password command(SCGCQ00293371)
 -PL: Fault 0x670B when sending SCSI Read Long to a 4K sector size SATA drive(SCGCQ00293644)
 -Fault 5813 while pulling direct attached SATA drives(SCGCQ00293898)
 -Invader (B0): Fast path IO with a requestor error is never started after a timer error(SCGCQ00294026)
 -Fault 0x61a2 while running IOs on a mix of SAS and SATA.(SCGCQ00294588)
 -0x584B Fault during whole port cable glitches(SCGCQ00295331)
 -L2 Parity error occurs when dumping SAScore registers via UART command(SCGCQ00296461)
 -READ BUFFER command in data mode executes with good status when Bufferid=0 and Buffer Offset=non(SCGCQ00297147)
 -Invader B0: CSET of SCGCQ00237417 incorrectly checks TxDMA Start register(SCGCQ00297565)
 -Fast path IO is never started after a timer error because RL granted bit is not set in MST(SCGCQ00297968)
 -Invader B0: All Drives lost (turn red) during IO + TM in CM(SCGCQ00298619 )
 -Invader B0: SATL:'Additional Sense' not set for REQUEST SENSE command when the drive is moved to IDLE power condition state(SCGCQ00300293)
 -(PL) Fault 0x5896.(SCGCQ00300593)
 -Firmware faults with PL fault code 0x5854(SCGCQ00302792)
 -Invader B0: 0x6001 fault while running a Max Outstanding IO count test with DDR(SCGCQ00304313)
 -Invader B0: Fault 584B during Destructive Domain test(SCGCQ00305407 )
 -Invader B0: PL not adding timer back when restarting IOs with Requestor Timer Error(SCGCQ00307944)
 -Invader B0: fault x5854 during I/T switching with IO and expander PHY resets(SCGCQ00307989)
 -PL fault 0xd10d during enclosure pull push(SCGCQ00310092 )
 -Invader B0: Fault 0x583D When starting IO to cascaded enclosure topology(SCGCQ00313872)
 -Fault 0x2667 running "pl dbg" when SMP Passthroughs with Immediate mode are in use(SCGCQ00314238 )
 -(FPGA) changes to firmware for B0 FPGA(SCGCQ00316360 )
 -A link may become stuck and unable to intiiate a connection(SCGCQ00317250)
 -Fault xD10E seen running IO with TM(SCGCQ00318724)
 -Invader B0: PL register dump doesn't include IOP Completion Queue(SCGCQ00319389 )
 -Fixed an Error in Code to Allow a Hardware Workaround to Be Correctly Enabled(SCGCQ00321025)
 -Invader A0 fault 583B fault(SCGCQ00321227 )
 -Invader B0: Fault 0x4101 while power cycling expanders(SCGCQ00321678)
 -5801 Fault running IO with random Task Management(SCGCQ00321865)
 -IO timeout for PL owned MID after sending QueryTask(SCGCQ00323459)
 -Invader B0: Fault 583A during Destructive Domain test(SCGCQ00323745)
 -Invader B0: pl dbg does not dump TBM registers(SCGCQ00326191 )
 -Invader B0: Fault 0x5851 during Destructive Domain test(SCGCQ00326809)
 -Low performance seen doing very low Q depths (1,2,3 outstanding IO levels) write IOs(SCGCQ00328670)
 -Added Hardware Cleanup Code to Prevent Fault 0x6002(SCGCQ00328671)
 -Added C0 Hardware Workaround to Prevent Fault x5801 seen running IO with Task management(SCGCQ00329584)
 -Link locks up when jammer is used to create wrong SATA FIS types.(SCGCQ00331579)
 -Change Hardware Workaround To Only Execute if Actual Cleanup is Done(SCGCQ00334830)
 -Invader B0: Maximum outstanding IOs not exceeding beyond 64(SCGCQ00335182)
 -Fixed Link Layer Interrupt Handler to Prevent Fault 0x4101(SCGCQ00338504)
 -Invader B0: 0x26B1 fault during large IO count to cascaded topology(SCGCQ00339747)
 -TargetMode unable to receive more than 64 IOs simultaneously (initially)(SCGCQ00341221)
 -PL: Read Log Ext command timeout.(SCGCQ00342412 )
 -7B00 fault due to incomplete table(SCGCQ00349335)
 -5811 fault when running port enable(SCGCQ00349337 )
 -DIAG_SHOW_MREQ_DETAIL feature fails to compile(SCGCQ00350762)
 -(IOA) Queue pointers calculations are incorrect(SCGCQ00353301 )
 -Back end PCI bring up(SCGCQ00353319)
 -Backend PCIe doesn't handle Legacy interrupts(SCGCQ00361845)
 -Bus and device are evaluated properly while configuring device's interrupts. (SCGCQ00363567)
 -Initial NVMe bringup fixes(SCGCQ00363615 )
 -Couple of PDB interrupt handling fixes(SCGCQ00378025)
 -Workaround for SGLOffset for PCIe targets(SCGCQ00383644)
 -Some PCIe config page fixes(SCGCQ00392850)
 -Fix several NVMe related bugs(SCGCQ00395578)
 -Check for Dword alignment when translating from IEEE64 to NVME PRP.(SCGCQ00397857)
 -Fixes for non read/write SCSI IO requests to a backend NVMe device(SCGCQ00399268)
 -Critical Fixes for PCIe IO Unit config pages (SCGCQ00400007)
 -D065 fault running AHCI IO with frame size > 128(SCGCQ00404358)
 -D300 fault on init with PCIe devices unsupported in Manufacturing Page 9(SCGCQ00406169)
 -Unaligned CE Image causes PL fault 0xd115 when using CE Auto Load(SCGCQ00408789)
 -Bad pointer access in plPciRcSetPcieLinkWidth(SCGCQ00409869)
 -Backend NVMe devices don't work if stored host page size is invalid(SCGCQ00410848)
 -NVMe: IO breakup due to MDTS or very large transfer size doesn't work(SCGCQ00413295 )
 -A write and verify command with many SGEs can cause a FW fault(SCGCQ00413390)
 -AHCI: Write command with FUA set to non(SCGCQ00414014)
 -Handle Stang BAD_ALIGNMENT exception differently(SCGCQ00414488)
 -AHCI: very large xfer count in one SGE causes fault 0xD300(SCGCQ00414589)
 -(PLLIB) Some PL Light routines are not included in the libraries(SCGCQ00415107 )
- Direct(SCGCQ00415180)
- Modify handling of a couple of Stang exceptions(SCGCQ00415459)
 -NVMe: Data corruption and unexpected IO failures(SCGCQ00418954)
 -265D fault running write IO to AHCI device(SCGCQ00419400)
 -MaxPayload/MaxReadRequestSize are getting set to strange values in some cases(SCGCQ00420926 )
 -Sas3.5: DL: SAS Device Page 0 access returns PCIe device (SCGCQ00423968)
 -26B5 fault when trying to init AHCI target(SCGCQ00426195)
 -D065 fault running IO to an AHCI target(SCGCQ00433598)
 -Build without PL_FEATURE_PCI_DEVICE_SUPPORT fails to compil(SCGCQ00434704)
 -(PL) New Spinup code does not compile with PL_FEATURE_PCI_DEVICE_SUPPORT set to zero(SCGCQ00434738)
 -SAS3.5: Add ALADIN feature macro and add pliAladin function calls to pliComplianceCheck.c.(SCGCQ00436117)
 -PCIe Switch upstream and downstream port relative configuration not proper(SCGCQ00436160 )
 -265E fault running IO and Abort Task TM(SCGCQ00438352)
- AHCI: D300 fault when using PCI IO path in single thread mode(SCGCQ00439523)
 -AHCI: read timeout after issuing MODE SENSE command(SCGCQ00441381)
 -Firmware hits Fault D10F while creating configuration on AHCI SATA drive(SCGCQ00442131 )
 -The TBM is initialized twice in Invader (and Dauntless) firmware(SCGCQ00443385)
 -AHCI: PL shouldn't fault when AHCI SGL translation encounters an invalid address(SCGCQ00443456)
 -E00D fault while running firmware translated read + mode sense(SCGCQ00444010)
 -Assertion failure fault D300 on PciIoCount adjustment(SCGCQ00447911)
 -ControllerPhyDeviceInfo is not properly populated for PCIe IO Unit Page 0(SCGCQ00448100)
 -NVMe: PL shouldn't fault when NVMe SGL translation encounters an invalid address(SCGCQ00448246 )
 -Fault 0x26b5 is hit when firmware tried to access attached PCI device memory.(SCGCQ00454824)
 -I/O timeout when Windows driver issues all I/O's via SCSI IO (no Fast Path)(SCGCQ00455679 )
 -AHCI: When an automated command starts right after a translated (non(SCGCQ00455698)
 -AHCI: Some internal variable accesses used the wrong index.(SCGCQ00457265) 
 -Data Corruption observed during IO + "random" TM to AHCI(SCGCQ00457786 )
 -AHCI init fails to find any devices in some cases(SCGCQ00458681)
 -0xD300 assertion seen when fast path engine throws error for internal PCI IOs.(SCGCQ00459137)
 -Dauntless FAULT EC07 upon port init with 4 or more devices connected behind PCI switch (SCGCQ00461370 )
 -PL: Re(SCGCQ00465527)
 -Dauntless FAULT 5801 running mixed IO with random task management test(SCGCQ00467347)
 -ECA2 running IO to 3 AHCI devicesSCGCQ00469042)
 -AHCI: Device discovery failed because of the missing MPI26_EVENT_DATA_PCIE_TOPOLOGY_CHANGE_LIST event(SCGCQ00469381)
 -4300 fault running IO to AHCI device after issuing a SATA passthrough message(SCGCQ00469630)
 -Fault E010 during AHCI IO(SCGCQ00470246)
-E403 fault during NVMe init(SCGCQ00470712 )
 -READ CAPACITY(16) SCSI IO to some AHCI devices result in command hang(SCGCQ00470905)
 -Additional fixes required for PL_PCI_DEVICE_MAX_DEVHANDLE usage(SCGCQ00471074)
 -Hang on error during PCIe discovery(SCGCQ00471277)
 -Dauntless FPGA: 670D fault while collect pl dbg(SCGCQ00471741)
 -IO submitted by host to fast path is stuck(SCGCQ00472322)
 -Fault 0xB0B0 with AHCI device that does not support port 0(SCGCQ00473624 )
 -Hitting MPI2_IOCSTATUS_INVALID_SGL.(SCGCQ00473919)
 -Device added event for the existing devHandle(SCGCQ00475377)
 -Unable to see AHCI devices off switch in CM(SCGCQ00478421)
 -PL: Firmware path read/write IOs to backend PCIe devices may time out(SCGCQ00481302)
 -PL: Last elements of NVMe submission and completion queues may not get initialized to zero(SCGCQ00486032)
 -NVMe Encapsulated Path Fixes(SCGCQ00493331)
 -NVMe: IO timeouts or fault after several command failures(SCGCQ00495200)
 -SAS3.5: In Cascaded Switch setup the parent device bridge number is always zero(SCGCQ00495900)
 -PL holds more than 128 frames while formatting vd created from 4 AHCI drives.(SCGCQ00498947)
 -Dauntless Fault 6001(SCGCQ00499669)
 -NVMe: 60D fault on encapsulated request failure(SCGCQ00504708)
 -Fault 6004 during Task Management Tests to AHCI devices(SCGCQ00505710)
 -PL: Task management aborted IO search may return faulty information(SCGCQ00524975)
 -D065 fault occurs during port enable with AHCI devices attached(SCGCQ00531377)
 -SAS3.5FW: PL: PCI: Use PliRegister for device registration instead of hardcoded value(SCGCQ00558177 )
 -Fault 6230 running Clear Task Set TM(SCGCQ00559714 )
 -Build errors (SCGCQ00568553 )
 -NVMe: Fix several mode page related bugs(SCGCQ00570058)
 -PCI command frame is tried to be obtained from non PCI firmware IO(SCGCQ00590513)
 -1901 fault when a FORMAT command issued to an AHCI target(SCGCQ00601939)
 -Some of the declarations and typedefs in pliDefs.h not conforming to code standard(SCGCQ00606222)
 -Incorrectly named PLI_RUNTIME_CONFIG flag definitions(SCGCQ00606259)
 -Delay timers are not used properly for some FPGA applications(SCGCQ00610868)
 -Few minor backend PCIe related changes(SCGCQ00613904)
 -Firmaware fault 0x26B5 observed when sending IOUnit Control Message with OPERATION SAS SEND PRIMITIVE to PCIe switch dev handle.(SCGCQ00619486)
 -Bug Fixes in NVMe Encapsulated IO Path(SCGCQ00621303)
 -NVMe: IEEE to PRP translator rollback issues(SCGCQ00626787)
 -Dauntless FPGA fault 4308 during 'init' FW 00.250.27.01(SCGCQ00654346)
 -Intruder/Ventura: Double define for set/get SAScore # could have 1 layer removed(SCGCQ00660419)
 -PL: Abort Task may fault if NVMe Init is pending(SCGCQ00669749)
 -Dauntless minimal build failure(SCGCQ00670226)
 -Fault xD204 when posting diag buffer(SCGCQ00671364)
 -Continuous plTxCtxMgrHighInterrupt on SASCORE1 attached SATA drive(SCGCQ00671683)
 -Dauntless FPGA: EF04 fault running IO and Abort Task TM to AHCI(SCGCQ00676418)
 -Intruder: Fix unprotected loop in plTargetProcessHardReset((SCGCQ00678870)
 -Intruder: Fault 0x4308 on SMP timeout in SMP Response Callback(SCGCQ00678877)
 -PL: IO Count not decremented correctly for encapsulated commands, resulting in a 0x6001 fault(SCGCQ00680608)
 -PL: Fault 0x4302(SCGCQ00682071)
 -Intruder: PL Fault 0x4307 while doing init(SCGCQ00682911)
 -Intruder: Fix plSataPassthrough.c to account for Multi Core work for plSataPassThrough.c(SCGCQ00684321)
 -4307 fault seen during PL initialization(SCGCQ00686953)
 -Intruder & Ventura: Fix plFpeHandleCompletorErrorInt() to compile for Ventura(SCGCQ00687645)
 -SCSI READ (16),(12),(10) command to an AHCI device not receiving LOGICAL BLOCK ADDRESS OUT OF RANGE(SCGCQ00690183)
 -Fault xD105 running IO to SATA devices(SCGCQ00692817)
 -SECURITY IN SCSI command timing out to AHCI device due to incorrect SATL translation.(SCGCQ00693169)
 -Intruder FPGA: 0x26B5 fault seen when accessing RxEEDPBuf of any SAS core(SCGCQ00698951)
 -Firmware faults when downstream port of attached PCIe switch sends uncorrectable fatal error for malformed TLP it received from connected device.(SCGCQ00699010 )
 -Ventura: Processor abort when initializing Txdma buffer(SCGCQ00700796)
 -Backend PCIe: AHCI spinup may fail(SCGCQ00702640)
 -(Sata Only) Scsi LOG SELECT to Sata drive fails when parameter list length is non(SCGCQ00702703 )
 -Debug code was inadvertantly checked in which causes phy layer initialization to not work for second core or phys > 0.(SCGCQ00705330 )
 -NVMe: IoCount not decremented on non read write encapsulated NVM command failure(SCGCQ00705495)
 -Fast path IOs are timed out.(SCGCQ00706941)
 -Dauntless FPGA: D205 fault when posting a host trace buffer during IO(SCGCQ00707374)
 -Intruder: 265D fault when FW controllered Spinup Feature is enabled in FW(SCGCQ00710078)
 -FIS Porting: Fix Issues with SAS Exception Queue Setup(SCGCQ00710464)
 -Fix issues in PL diagnostic code(SCGCQ00710497)
 -Intruder FPGA: 0x6230 Fault during whole port glitches (SCGCQ00711100)
 -Drive SAS Address in gplControllerPhy structure being overwritten, resulting in drive loss(SCGCQ00712955)
 -265D fault on AHCI spinup (SCGCQ00714811 )
 -NVMe devices may fail to initialize((SCGCQ00715163)
 -Intruder: Don't display all message frames for pl dbg register dump (SCGCQ00716613)
 -PL:Overlapping 0x61xx Fault codes (SCGCQ00716742)
 -gplControllerPhy indexing should be per chip phy, not core phy (SCGCQ00718620)
 -Fault xD015 seen running IO when Task Management occurs (SCGCQ00718761)
 -Ventura: Device does not show up when connected to phy 1.(SCGCQ00718771)
 -Fast path completor engine throws error for IOs that don't have appropriate flags set in fast path mid state table (SCGCQ00719653)
 -PL SATL: Fault 6201 When Sending SCSI Security Protocol In Command to SATA Drive(SCGCQ00721212)
 -Ventura: wrong SAS core address in FPE(SCGCQ00722553 )
 -PL (Ventura): Fast Path IOs submitted through a message should not immediately be submitted to the Fast Path Engine for non PCIe devices(SCGCQ00724355)
 -Host stopping IOs to PCIe device while task management requests are outstanding to the device.(SCGCQ00724399)
 -Dauntless FPGA: fault D024 while running abort task TM.(SCGCQ00726551)
 -NVMe: devices always fail to initialize(SCGCQ00729685 )
 -Ventura: Incorrect Case in Function Parameter(SCGCQ00734961)
 -Intruder FPGA: Fault 0x584F while running CM Block Move and Task Management Test to two direct(SCGCQ00735409 )
 -Intruder FPGA: Fault 0x5828 while power cycling random expanders on both cores(SCGCQ00735635)
 -Fault 0x510B while running stress to 7 cascaded expanders(SCGCQ00736679)
 -Problems in Tx DMA single to dual context mode switch and vice versa on multi SAS core(SCGCQ00737078)
 -Dauntless: tip code appears to be broken(SCGCQ00737126)
 -Fault 0x6001 While running Task Abort to topology of only SATA Drives during I/O.(SCGCQ00740832)
 -PL: add temporary config page buffer items to gplDynamicMemory(SCGCQ00741788)
 -Ventura: Link register is not set in fault print(SCGCQ00747257)
 -Ventura: Bad merge backed out the fix in (SCGCQ00748108)
 -Dauntless FPGA: Read Error when running Medusa IO with Abort Task Set TM to NVMe drive(SCGCQ00752414 )
 -PL: uninitialized NumPhys(SCGCQ00757724)
 -Ventura: Processor abort on I/O with sense data(SCGCQ00762270)
 -Fault xD117 seen when running IO with Task Management Abort Task and Abort Task Set TMs being issued(SCGCQ00762899)
 -Fault EFF1 while running task management with fast path and non fast path devices(SCGCQ00764185)
 -Dauntless FPGA: EC38 fault upon initialization(SCGCQ00765364)
 -Fix compiler(SCGCQ00765443)
 -Ventura: New PCIe Discovery implementation stuck in direct attached state.(SCGCQ00768164)
 -pliProtos.h contains 2 internal protos for sim/fake IO(SCGCQ00769245)
 -Intruder: Fix the spinup register read to get the spinup group for multi SAS core.(SCGCQ00771113)
 -FW Controlled Spinup: Repeated interrupts occur for unhandled spinup requests beyond max targets allowed for a spinup group(SCGCQ00771115)
 -pl: Unexpected usage of 64 bit math lib in plPciNvmeFillInquiryData((SCGCQ00771167)
 -pl: backend PCIe: couple of PCIe IO Unit Page 1 issues(SCGCQ00776230)
 -Intruder FPGA: Fault 0x584F running Block Move and Task Management from Core 0 to Core 1(SCGCQ00776360)
 -NVMe: EF08 fault during non target reset task management(SCGCQ00776392)
 -Intruder FPGA: Fault 0xC00C while running Initiator and Target Mode on Intruder Cores(SCGCQ00776417)
 -Intruder: Incorrect parameter is getting passed in plGetQuadPhyIndxFromCorePhyNum((SCGCQ00785455)
 -PL: incorrect logic in determining setting for CloseOptimize(SCGCQ00786213)
 -Intruder FPGA: 0xD20C Fault While Running Stress From 4 Initiator System to Target Mode FPGA(SCGCQ00791373)
 -AHCI D300 fault during a non(SCGCQ00792570
 -Intruder FPGA: Fault 0x7400 Running Stress and Expander Resets in I/T Setup(SCGCQ00793228)
 -Ventura: PCIe Discovery problems observed with device reset test.(SCGCQ00793909 )
 -NVMe: D300 fault on malformed chain to PRP list SGL(SCGCQ00794103)
 -Fault 6016 while running clear task set TM to NVMe device(SCGCQ00795690)
 -pl: backend PCIe: special case cascaded switch issues(SCGCQ00799848)
 -Dauntless FPGA: D024 fault while running TMs in Linux(SCGCQ00800431)
 -Intruder FPGA: Fault 0xC00C while running IO stress and expander resets in Initiator/Target Setup(SCGCQ00800478)
 -Intruder: Link event codes are not properly converted from hardware to MPI values(SCGCQ00806568)
 -Backend PCIe: FxCore error bit clearing(SCGCQ00813507)
 -Dauntless FPGA: Data Corruption reported on multiple tests(SCGCQ00813954 )
 -Fault D300 when issuing Scsi SecurityProtocolInOut command to an AHCI device.(SCGCQ00815172)
 -FW Controlled Spinup: Fixes in spinup request entry cleanup(SCGCQ00815536)
 -Dauntless FPGA: IOs being aborted during "straight IO" test(SCGCQ00815660 )
 -Intruder: incorrect version number in PL library builds(SCGCQ00818770)
 -Ventura: Sascore 1 links do not come up(SCGCQ00822145 )
 -pl: backend PCIe: AHCI init timing issues(SCGCQ00822349)
 -Dauntless FPGA: EFF1 fault on init(SCGCQ00822595)
 -Remove Aladin Reset Code in PL Start of Day(SCGCQ00823445)
 -Ventura: Phy register addressing is incorrect(SCGCQ00825050)
 -FPGA: Fault 0xD34C on intitializtion with SATA drive attached(SCGCQ00825828)
 -Dauntless FPGA: Fault D065 during CM init to AHCI drive in non(SCGCQ00827582)
 -Ventura: "iop arm table" crashes due to missing string(SCGCQ00829296)
 -Ventura: backend PCIe: fix some issues encountered upon merge of SCGCQ00829039.(SCGCQ00830809)
 -Ventura: Fix PCIe discovery out-of-resource handling(SCGCQ00831671)
 -Change define used for SED POM size to true 128MB size, added new define for emulator.(SCGCQ00832044)
 -Ventura: PCIe discovery (SCGCQ00832125)
 -Use the address, not value of register to set base for the IOA shadow Register PIM(SCGCQ00832543)
 -Fault 0xD63C when trying to create/use an 8K PIM(SCGCQ00832557 )
 -Fix code for handling FxCore Requester and Completer errors as per comments in review.(SCGCQ00834567 )
 -Intruder A0: 0x4330 Fault When Multiple SATA Drives Are Attached Simultaneously(SCGCQ00834931)
 -PL: Fix SATA Function so that it's More Straightforward (SCGCQ00835199)
 -PL: Update link layer register that should be programmed differently for intruder(SCGCQ00835524)
 -A device initialization call was being made for all end devices, that doesn't apply to SED(SCGCQ00836070) 
 -Ventura: backend PCIe: host bringup fixes, part 1(SCGCQ00837192)
 -Intruder: Disable DMA Engine Overrun error for Intruder and beyond based on Hardware feedback(SCGCQ00839532
 -Intruder A0: Drive information is not removed completely from controller when enclosure is detached(SCGCQ00839951)
 -PL: Fault 0x430B seen when connecting enclosure to upper quad(SCGCQ00840596)
 -PL: Fault d060 observed when running IOs with link_reset Task management command in a loop(SCGCQ00840603)
 -Ventura: SAS_R31_HACK doesn't always compile correctly(SCGCQ00841016)
 -Fault 0x7C54 seen during I/T switching(SCGCQ00843298)
 -Intruder A0: Fault 0x5872 during I/T Switching(SCGCQ00844812)
 -Ventura: backend PCIe: fix some scattered bugs(SCGCQ00845780)
 -Ventura: Fault during pl debug dump(SCGCQ00848069)
 -Cleanup IOP Access to gplPtrPdbRegs(SCGCQ00849748)
 -IOP firmware accesses PL firmware directly without going through PLI(SCGCQ00849749) 
 -Ventura: backend PCIe: EC82 fault on NVMe TM with specific vendor AHCI drive present(SCGCQ00849829)
 -Build problem when firmware controlled spin up is disabled(SCGCQ00850667)
 -Ventura: several faults occur with mixed SAS and NVMe IOs(SCGCQ00851227)
 -PL: SATA Command getting stuck in PL after issuing Start Stop command with immediate bit set(SCGCQ00851287)
- Intruder A0: Fault 0x6111 during I/T Switching(SCGCQ00852833)
- 0x265D Fault while running mixed PCI and SAS IOs(SCGCQ00853311)
 -Intruder A0: 265D fault observed during link reset task management with IO (SCGCQ00853930)
 -Ventura FPGA: Fault 0x681E encountered during overnight run using RedEye(SCGCQ00854322)
 -PL: Fault 0x430B seen when connecting several enclosures(SCGCQ00854697)
 -TLB exception when showing PL ring buffer(SCGCQ00855026)
 -PL: Limited to 16 PHYs on one SGPIO bus (SCGCQ00855674)
 -Firmware Controlled Spinup: Spinup group with multiple drives may never be allowed to spin(SSCGCQ00855675
 -PL: Format command doesn't work on SATA drives when FMTDATA bit is 0(SCGCQ00856366)
 -PL: Unmap command fails with Check condition Invalid field in parameter list(SCGCQ00856369)
 -Firmware Controlled Spinup: Cable Pull Tests with SPL(SCGCQ00856501)
 -Ventura: Target IOs in a persistent connection hang(SCGCQ00856874)
 -Ventura: Target mode clearing of midvalid should be workaround(SCGCQ00857062)
 -Ventrura: Accessing Mode Sense pages for NVME Results in alignment fault(SCGCQ00857247)
 -Firmware Controlled Spinup: GroupSpinningCount May Not Be Adjusted Correctly for Legacy SAS Drives(SCGCQ00858694)
- PL: Fault 0x7C54 seen when running IO with hard resets and config reads(SCGCQ00859243)
 -Disable FwSpinupAck print for periodic notify(SCGCQ00860244
 Intruder A0: WriteBuffer in 'Write Data' mode executes with good status when Bufferid=0 and Buffer Offset=non(SCGCQ00860452)
 -Intruder A0:WriteBuffer in 'Write Data' mode executes with good status when Bufferid=0 & Param List length != 512.(SCGCQ00860454)
 -Ventura FPGA: 0x265D fault during Max topology PCIe discovery(SCGCQ00861693))
 -Ventura FPGA: Faults observed when powering off/on populated PCIe switch(SCGCQ00861780)
 -Ventura: IOA Cuda Timer Overflow issues(SCGCQ00862001)
 -Ventura: NVMe: PL translated non read write commands may time out(SCGCQ00862206 )
 -Handle FxCore Requestor Disabled Exception that follows Submission queue timeout exception for NVMe device(SCGCQ00864142)
 -Number of Spinup Entries Should Be Reduced(SCGCQ00864345)
 -PL: SFF(SCGCQ00864613)
 -PL: Minor modification for the 5872 workaround(SCGCQ00865238)
 -Ventura: backend PCIe: FxCore may generate invalid exception 0xFF(SCGCQ00865819)
 -Current Config of "pl status" command output is not clear.(SCGCQ00866270)
 -Ventura FPGA: Fault 0x6230 while running IOs and issuing target reset task managements(SCGCQ00866294)
 -Ventura: When processing SAS core interrupts, sometimes status register indicates no active interrupts(SCGCQ00866361)
 -Ventura: backend PCIe: backend completion timeouts occur when the FPGA is heavily loaded(SCGCQ00866758)
 -Change the naming of library defines DEBUG and TARGET to avoid conflicts with customers(SCGCQ00866760)
 -Ventura FPGA: Fault 0xD102 after several hours of mixed(SCGCQ00867258)
 -Ventura FPGA: 6001 fault starting IO(SCGCQ00868569)
 -PL: SATA I/O times out right after a Start Stop Unit command with immediate bit set to 1(SCGCQ00868995)
 -Ventura: Structures not being put in IOA Local RAM(SCGCQ00869574)
 -Ventura FPGA: Fault 0x61A6 while running IOs and issuing target reset task managements(SCGCQ00870402)
 -PL: A pointer needs to be reinitialized to prevent out of bound access(SCGCQ00871248 )
 -PL: Missing break statement in PL control request handler(SCGCQ00871320)
 -Ventura FPGA: 0x6C02 during Random TM and IOs(SCGCQ00871341)
 -Ventura: Fault 0xd102 observed during IO + TM testing on direct attached NVMe drive(SCGCQ00871397)
 -Ventura: backend PCIe: target reset to AHCI device times out(SCGCQ00871680)
 -PL: Fix bad coding style in plGetSpinupGroup(SCGCQ00871683)
- Ventura: Fault EC8A on async removal of switch attached PCIe target(SCGCQ00871718 )
- Ventura: firmware path IOs may time out(SCGCQ00871792)
- PL: Check Return Status of Memory Move Function(SCGCQ00871805)
 -Root complex port mark enabled even if all the phys are disabled in nvdata(SCGCQ00871999)
 -PL: Firmware does not fill in SAS IO Unit Page 16 Timestamp field correctly(SCGCQ00872141)
 -Ventura FPGA: 0x1202 fault with IOs and Random TMs(SCGCQ00872717)
 -Intruder A0 : Fault 0x430b while Discovery in Target Mode setup(SCGCQ00873776)
 -Ventura: backend PCIe: fault occurs with AHCI IOs in non(SCGCQ00877613)
 -Ventura: backend PCIe: 1901 fault on AHCI command failure(SCGCQ00878246)
 -NO_FPE_HW compile option updates(SCGCQ00879534)
 -Ventura: backend PCIe: issues related to Axi2Shell error handling(SCGCQ00880773)
 -PL: Fault 0x7400 with Modified Runtime Configuration for Expander(SCGCQ00880957)
 -Ventura: backend PCIe: (AHCI) firmware hangs on translated SGL full of 0(SCGCQ00881278)
 Transition from MPI SAS IO Unit Control request to IO Unit Control request coding incomplete(SCGCQ00883285)
 -Ventura FPGA: IO stopping during stress(SCGCQ00883428)
 -Ventura: PCIe SW error handling tweaks(SCGCQ00883994)
 -PL faults on PNPR Error Syndrome interrupt that is hit during link glitch test(SCGCQ00885805 )
 -Ventura: port some FPE start path fixes to PL Light(SCGCQ00886430))
 -PL: Spinup control has incorrect error guard(SCGCQ00886966)
 -Ventura: NVMe Serial Number Not Copied From Drive(SCGCQ00887003)
 -Ventura FPGA: 'pl status' doesn't reflect hot removal of a NVMe Drive connected to a switch.(SCGCQ00888012 )
 -Ventura: RingBuffer Print Error of Device's IO Count(SCGCQ00888114)
 -Ventura: port some FPE start path fixes to PL Light(SCGCQ00888286)
 -Unable to issue Start Stop Unit to a sata device(SCGCQ00890804)
 -Tiger/Stryker: Fix tiger firmware build and build all issues(SCGCQ00894132)
 -Tiger/Ventura: change FXCore init delay to coding standard format(SCGCQ00894651)
 -Ventura: backend PCIe: FPE MaxPcieCoreNum is incorrect(SCGCQ00895285)
 -Ventura: Inconsistent use of plGetDmaTransQueueEntry((SCGCQ00897149)
 -PL init taking excessive time(SCGCQ00897938)
 -Ventura FPGA: Fault xEF09 during phy cable glitch on NVMe direct attached drive(SCGCQ00908689)
 -PL: Update internal files to latest specifications(SCGCQ00913173)
 -Ventura: Invalid Q Entry for SAS(SCGCQ00915170)
 -Ventura: backend PCIe: reformulate switch WWID(SCGCQ00915987)
 -Ventura: Additional settings for hw workaround in SCGCQ00915170 (SAS(SCGCQ00916873)
 -Not able to link SASFW_Ventura_Phase_0.6 00.250.49.00 Pl library(SCGCQ00921951)
 -Fault 0xd332 is hit while translating a SCSI IO that shares SGL with other IO or IOs(SCGCQ00923195 )
 -Ventura: Fault 0x1D02 during force link down of DA NVMe device that failed init(SCGCQ00924457)
 -IO count in a Rare case for a PCI Device is Not Decremented.(SCGCQ00925182)
 -Fault 0x4330 seen if an SMP Passthrough causes a TxDMA error(SCGCQ00927711)
 -TigerStryker: Fix pl library build for liger release(SCGCQ00930678)
 -PL: Optimize FPE(SCGCQ009316620)
 -PL: Ventura incorrectly stores tail pointer in head pointer(SCGCQ00932450)
 -Ventura: Tip code faults with 0xECA6SCGCQ00933078)
 -Ventura: separate reset of CSW core from PBD(SCGCQ00933765)
 -PL Ventura: MultipP bit not set in Inquiry(SCGCQ00933818)
 -Ventura: setting CSW protocol mode does handle setting HW Mode with PCIe devices(SCGCQ00934298)
 -PL: Unexpected Open Reject (Protocol Not supported) is observed from target mode(SCGCQ00934341)
 -Ventura: BUSY TIMEOUT PERIOD incorrect for NVMe drives(SCGCQ00934896)
 -PL: PL code is not supposed to use division(SCGCQ00934930)
 -Ventura: backend PCIe: value written to PDB clock enable register may be incorrect(SCGCQ00938502)
 -Ventura: Misc initial bring-up work-arounds(SCGCQ00938539)
 -PL: MPI device driver state machine is confusing(SCGCQ00938627)
 -Ventura: A0 sas phy bringup issues(SCGCQ00940200)
 -Ventura: PL should not be looking for Phy Interrupts in SASConfigRegs(SCGCQ00940270)
 -pl: SGL debug printer ignores SkipCount(SCGCQ00941786)
 -Tiger FW: Recursive 0x265D fault(SCGCQ00943006)
 -Tiger: PSB PEX hardware initialization code requires data synchronization barrier(SCGCQ00944153)
 -Dauntless Builds Not Completely Removed.(SCGCQ00944759)
 -Tiger: Firmware init causes 0xED00 fault(SCGCQ00944868 )
 -Tiger: Fault 0x2667(SCGCQ00945971)
 -Tiger: Fault 0x430A on init(SCGCQ00947159)
 -Ventura: backend PCIe: IOs to an NVMe device fail if they are larger than the device's MDTS(SCGCQ00948252)
 -Ventura: SATA Init Always Fails(SCGCQ00948281)
 -Trace buffer has garbage at SOD(SCGCQ00948938)
 -Ventura FPGA: Hitting x430A fault during Hot Plug less than 3 seconds(SCGCQ00949143)
 -Ventura: PL Status command does not display SAS address(SCGCQ00949973)
 -Ventura: Data abort when booting harpoon image(SCGCQ00950072)
 -Tiger: PCIe discovery and configuration fixes(SCGCQ00950664)
 -Ventura: Fix the PBAM Inframe core activity selection mapping(SCGCQ00954393)
 -Ventura: backend PCIe: need to configure link width in the DM Core before bringing up the link(SCGCQ00954714)
 Ventura: backend PCIe: fix a couple of NVMe related issues(SCGCQ00979716)
- Ventura: PCI links get reset when in END POINT mode(SCGCQ00981060)
- PL: 0x430B firmware fault on a 9305(SCGCQ00981252)
- Ventura: backend PCIe: intermittent IO timeout with fast path plus firmware breakup path IOs(SCGCQ00981260)
- Ventura: backend PCIe: PL NVMe read/write breakup IOs fail badly(SCGCQ00983674)
- Tiger: Silicon build not working with new Tiger CCR header(SCGCQ00987111)
 -Ventura: Remove Tx phase slip setting workaround(SCGCQ00987742 )
 -Ventura A0: Devices are intermittently showing up or not present at all(SCGCQ00987752)
 -Ventura: Total IO count in pl status not incremented for SAS/SATA devices (SCGCQ00988653)
 -PL: Firmware is hung in infinite loop during device handle pre(SCGCQ00990651)
 -Ventura: backend PCIe: hang may occur when a backend PCIe link goes down(SCGCQ00991209 )
 -SAS IO Unit Page 1 (SCGCQ00992048)
 -Ventura: Switch to parity initialization work(SCGCQ00992931)
 -Ventura: backend PCIe: ED08 fault occurs with backend PCIe enabled and phys disabled(SCGCQ00993194)
 -Ventura: backend PCIe: fault occurs when backend PCIe support is disabled in NVDATA(SCGCQ00993887)
 -Ventura: Invert PBAM GPIO LED data polarity(SCGCQ00993950)
 -Ventura: Fix build all error(SCGCQ00995348 )
 -Ventura: backend PCIe: fault occurs on recoverable PDB init failure(SCGCQ00995568 )
 -Ventura A0: Power Management functionality for Partial or Slumber capable SAS or SATA devices not enabled(SCGCQ00997277)
 -Ventura: backend PCIe: link always comes up with maximum width(SCGCQ00997661)
 -Ventura: recursive fault on fault with backend PCIe support disabled at runtime(SCGCQ00997681)
 -Tiger: Data corruption reported for NVMe IOs 8KB and higher(SCGCQ00998637) 
 -Devices not getting discovered with PL version 0.250.54.77(SCGCQ00999505)
 -Ventura: backend PCIe: 265D fault on 'pl dbg' with backend PCIe support disabled at runtime(SCGCQ00999664)
 -0x5841 Fault occurs while running destructive domain testing(SCGCQ01000131)
 -Ventura: Fault 265D occured while trying to read SAS IO Unit page 16(SCGCQ01000229)
 -Ventura A0: 7C55 fault when performing port_break between HBA and expander cable break with 4K IO size(SCGCQ01001139)
 -Ventura A0: Fault 0x6108 while running TMs & SMP commands(SCGCQ01001258)
 -Adapter fails to respond to diag reset while faulted(SCGCQ01001666)
- Tiger FPGA: Fault 0x6230 during initialization(SCGCQ01001972)
 -Ventura: EC22 fault occurs after a SASCore transmit hardware interrupt(SCGCQ01002020)
 -Tiger: IO failure with two or more NVMe drives.(SCGCQ01002855 )
 -Tiger FPGA: 0x2671 during IO and Init(SCGCQ01003082)
 -0x430b fault is seen while running IOs & link resets on Ventura HBA Phys(SCGCQ01004126 )
 -Ventura: backend PCIe: fault occurs when link configuration is invalid(SCGCQ01004373)
 -PL: Firmware doesn't compile with MPI Device support enabled(SCGCQ01004853)
 -Firmware crashed with PL Fault d073 when running IO on multiple R1 VDs(SCGCQ01004990 )
 Ventura: backend PCIe: need to verify that the page size used by PL is supported by the device(SCGCQ01005076)
 -Ventura A0: Fault 0xD10D when running I/O's to Target mode controller(SCGCQ01005338)
 -Ventura: backend PCIe: need to take PDB testmux hardware out of reset at start of day(SCGCQ01005342)
 -PL (Ventura): Inquiry EVPD 0x83 is not unique for some devices(SCGCQ01007567)
 -Tiger FPGA: Firmware faults with 0xD20F when posting trace buffer(SCGCQ01007596)
 -PL: Memory corruption when connected to downstream MPI device(SCGCQ01010196)
 -0x6001 Fault while running port glitch cable break tests.(SCGCQ01010466)
 -Ventura: Remove Prevail references(SCGCQ01011088)
 -Tiger FPGA PL: Link layer is sending out old sas addres after swapping out a drive.(SCGCQ01012066 )
 -PL: IO to MPI SED attached devices fail(SCGCQ01012207)
 -Ventura SED handling: Fixes to handling to SED attach devices(SCGCQ01012504)
 -Ventura PL: Incomplete error handling in MPI SED event handling code(SCGCQ01013576)
 -Ventura: Sequential Writes Performance Very Low (SCGCQ01013913)
 -IOs stop running TM injection test(SCGCQ01013927)
 -PL: SED DevHandle translation code incorrectly translates DevHandles(SCGCQ01013965)
 -Intruder: SAS device removal is not updated in configuration page(SCGCQ01014609)
 -PDB MEM BARs not updated properly when NVDATA settings are used as a fallback method to BAR(SCGCQ01014618)
 -Ventura: backend PCIe: memory sync is missing from a couple of IO start paths(SCGCQ01014812)
 -Ventura: backend PCIe: couple of issues related to resource configuration(SCGCQ01014981)
 -Ventura PL: Remove deprecated MPI SED Initialization step(SCGCQ01015440)
 -Ventura: Sas/IOA deadlock(SCGCQ01016130)
 -Ventura: backend PCIe: workaround for lane breakage on backend PCIe link down(SCGCQ01017060)
 -Tiger FPGA: Fault 0xEE13 while initializing an MPI device with a non(SCGCQ01017450)
 -Ventura A0: Performance Counters not working as expected(SCGCQ01018523)
 --Ventura A0: 583D fault when running Port Glitch cable break between expanders(SCGCQ01018657)
 -Marlin: backend PCIe: various bringup issues(SCGCQ01018771)
 -Ventura: backend PCIe: lanes may fail to come up(SCGCQ01018960)
 -Ventura: backend PCIe: allowed cascaded switch count should be 1(SCGCQ01019728)
 -Ventura: backend PCIe: EC0D fault on link drop during NVMe init(SCGCQ01019754)
 -Tiger FPGA: New Task File Interrupt being hit (0x6815 fault)(SCGCQ01020348 )
 -Ventura: NVMe: Supported WRITE LONG flags mismatch the current SCSI(SCGCQ01020474)
 -Ventura: backend PCIe: on disable, need to deconfigure backend PCIe sooner(SCGCQ01021385)
 -Tiger FPGA: Link status change event causing 0x6230(SCGCQ01022790)
 -Ventura PL: SED DevH translation still doesn't translate correctly(SCGCQ01023107)
 -Tiger FPGA: 0xEF20 fault with NVMe in Stryker mode(SCGCQ01024099)
 -Ventura A0: Fault 0xD091 while creating partitions during Fast path enable & disable test (SCGCQ01025048 )
 -Fault 0xD101 observed during IO stress while sending a read command to a SATA drive with LBA out of range(SCGCQ01025055)
 -PL: Tiger faults with code 0xEC86(SCGCQ01025380)
-Ventura PL: Handle secondary path-completion interrupt beating completion entry writes(SCGCQ01025621)
 -Ventura: NVMe: SGL translation fails if DDR flag is set in an IEEE chain element( (SCGCQ01026956)
 -Ventura: NVMe: SGL translation may fail with unaligned first SGE(SCGCQ01026995)
 -Ventura PL: Invalid reply message and fault 0x1902 seen with SED attached IO(SCGCQ01027169 )
 -Ventura: several issues encountered during non fast path IO and TM testing(SCGCQ01027346)
 -Ventura: backend PCIe: EC30 fault on surprise link down(SCGCQ01027780)
 -(SATA Only) Fault 0x4203 observed on running heavy IOs to SATA drives with IOs causing firmware exception.(SCGCQ01029537)
 -Ventura Tiger: Task Management fails to abort IOs in firmware Pend List for SED attached devices(SCGCQ01029633))
 -Ventura A0: Pl faults with fault code 0xd10f running SAS IO(SCGCQ01031904)
 -Ventura Tiger: 0x265d Fault while running Task Management Test to tiger attached SATA drive(SCGCQ01032769)
 -Tiger Ventura: Remote MPI device (SED) beyond first found would get incorrect IO completion Q and Tail pointer addresses(SCGCQ01032856)
 -PL: Firmware faults with code 0x265D during PCIe enumeration(SCGCQ01033445)
 -Ventura: backend PCIe: several issues occur during link breaks behind a switch(SCGCQ01033463)
 -Tiger PL: Internal switch is not being properly hidden from the host(SCGCQ01034219)
 -Ventura A0: Fault 0x620E on NVMe drive pull when I/O stress is running against all drives(SCGCQ01034404)
 -Tiger FPGA: Fault 6001 is seen When run IO + TM on SAS/SATA behind expander(SCGCQ01036331)
 -Mismatch in WWID returned in PCIe Device Page0 and PCIe Device Status Change event.(SCGCQ01037372)
 -Tiger Ventura: Incorrect reply descriptor Q address used for any SED beyond the first one(SCGCQ01038414)
 -Fault 0x5881 due to not handling a new interrupt(SCGCQ01038536)
 -Tiger Ventura: Fault when running IO to multiple Tiger/SED attached drives(SCGCQ01038568
 -Ventura: backend PCIe: 61A5 fault on frequent errors involving an NVMe device(SCGCQ01039087
 -Ventura Tiger: Fault 0x7008 while initializing firmware with an expander attached topology behind tiger(SCGCQ01039193)
 -Fault during Aladin CLI commands.(SCGCQ01040069)
 -Ventura Tiger: Fault 0x265d when forwarding Internal Abort Task for a MID to an SSP Target from a downstream Tiger to host(SCGCQ01040995 )
 -Tiger FPGA: Abortable IO timeout are seen during IO and TM on SAS/SATA behind expander and IO on direct attached NVMe(SCGCQ01043036)
 -Ventura: backend PCIe: fix some issues with the SERDES link down workaround(SCGCQ01043043)
 -PL returns incorrect PCI address returned for IOP mapped resource element.(SCGCQ01043532)
 -Fix FW DMA of trace data when the Host posts a Trace Buffer(SCGCQ01043735)
 -Tiger: New code using non standard function header style(SCGCQ01043926 )
 -Tiger FPGA: Fault 6230 is seen during IO and TM on direct attached SATA(SCGCQ01045612)
 -Ventura: backend PCIe: EC30 or EC70 fault on direct attached link down(SCGCQ01046534)
 -Ventura A0: NVMe drives missing after few Port glitches between HBA and PCIe Switch(SCGCQ01046704)
 -Device Specific parameter field of mode page header has incorrect value for Mode Sense command send with DBD bit set for SATA and NVME devices(SCGCQ01047156)
 -Tiger: IO stops to devices after link reset, drives either get removed or IO times out.(SCGCQ01047475)
 -IOP: Firmware faults with 0x265D when issuing a TM to a device behind a SED which is no longer connected(SCGCQ01049418)
 -PL fault 0xd0d0 is seen when IOA hardware interrupts for invalid completion entry(SCGCQ01052174)
 -Ventura A0: Running all Task Management types to only PCIe devices results in fault 0xECA3(SCGCQ01053437 )
 -PL does not map IOP requested resource to backend PCI space with AXI bus attribute and faults(SCGCQ01054900)
 -Ventura with Tiger devices attached and Fast Path disabled in IOUnit 1 results in x7008 fault on initialization(SCGCQ01056872 )
 -Ventura: backend PCIe: PL rejects NVMe device with the maximum supported BAR size(SCGCQ01057661)
 -Ventura: Single/Dual context mode not set correctly(SCGCQ01057740)
 -Ventura: backend PCIe: need to set a Gen3 related control bit in backend PCIe hardware(SCGCQ01058243)
 -Ventura: backend PCIe: configure root port Max Read Request Size(SCGCQ01058260)
 -Ventura: FW events are sent in incorrect order when DA SATA drive is hot removed(SCGCQ01059293)
 -Ventura: 8 LUN Target Using Linux Driver Performs 10% or more slower than previous SAS3 products(SCGCQ01060022)
 -Asynchronous External Abort during SOD. Found during COL cycles(SCGCQ01060269)
 -PL: Handle plSMPPhyControlSend() return status(SCGCQ01061458)
 -Tiger: Improve DPC handling(SCGCQ01062268)
 -PL: Some error conditions not logged(SCGCQ01063603)
 -Broadcast Interrupts Cannot be Masked(SCGCQ01064110)
 -Ventura: backend PCIe: various faults occur after a short link glitch(SCGCQ01064269 )
 -Ventura: backend PCIe: reading config space for debug may break other PL subsystems(SCGCQ01065697)
 -Tiger: Fault 0x430B when unregister is attempted for an Ventura DevH for a Tiger attached drive(SCGCQ01066917)
 -Tiger: Tiger Attached NVME drives did not have Fast Path prints turned on for the Ventura instance of the device(SCGCQ01066922)
 -Ventura: 265D fault occurs when the 'pl pci prot' debug command is used(SCGCQ01068102 )
 -Ventura: Target stalls after many hours operating at 700K+ IOPs(SCGCQ01068910 )
 -NVMe: Allocation Length field of SCSI commands is not handled properly for NVMe drives.(SCGCQ01069397)
 -Ventura: Aladin CLI causes system lock up when running on Crusader(SCGCQ01069804)
 -(SATA Only) Allocation Length < 16 Bytes for REPORT LUNS Command is not Handled Properly for SATA Drive(SCGCQ01070183 )
 -If SATA_FIS_PORTING feature complied out, FxCore exception Queue will be sized to 0(SCGCQ01070394 )
 - SCSI Read Capacity - 16 processed successffully for incorrect service action field(SCGCQ01070692 )
 -SMR SATL: SCSI VPD pages updated with Peripheral Device Type of 0x14 for SMR Host Managed ZAC drives(SCGCQ01070850)
 -For NVMe drives mode sense command failed for PAGE CODE=0x3F and SUB PAGE CODE=0xFF(SCGCQ01070881)
 -PL: SATL: With VALID bit set INFORMATION field in Sense data is not populated when REPORT ZONES Command fails for LBA out of range(SCGCQ01071132)
 -When processing IOs with partial DIF, IOs may hang.(SCGCQ01071316)
 -Tiger FPGA: Fault 0xEC92 on initialization(SCGCQ01073866)
 -Ventura A0 UTP: Fault 61A6 seen while running pcie lane breaks with IOs(SCGCQ01075089
 -Tiger FPGA: NVMe drive drops off while running a mix of IOs and Task Managements(SCGCQ01075180
 -PL: SMR: Enhance the error handling conditions of SMR ReportZones SATL(SCGCQ01077555
 -Tiger FPGA: Ventura 0x6060 during TM to NVMe(SCGCQ01080912
 -Ventura: backend PCIe: PCIe link associated with root port 0 sometimes fails to come up(SCGCQ01082753
 -Ventura Tiger: Do not configure completion time limit for MPI devices(SCGCQ01083308
 -Ventura Tiger: Timeouts for Internal Task Managements not set correctly.(SCGCQ01083603
 -Ventura/Marlin: backend PCIe: couple of PCIe related diag command issues(SCGCQ01084205
 -IO Timeout when running IOs and TMs(SCGCQ01085128
 -Ventura PL: 0x265D fault when initializing a SED(SCGCQ01086075 
 -PL Tiger: Fix plPciRcGetPexPortType(SCGCQ01088652
 -Tiger FPGA: NVMe drives go missing as soon as IO is started(SCGCQ01089519
 -Initialization hangs on Harpoon controller(SCGCQ01092071
 -Tiger FPGA: New PCI Link Config code causes Tiger FPGA to fault with 0xEC3D during init(SCGCQ01092288
 -Tiger PL: SGLs with DDR DLAS never complete(SCGCQ01092466
 -A 7C41 Fault occurs when an Internal IO timeout occurs(SCGCQ01093487
 -Ventura: NVMe: No INQUIRY Response Seen for NVMe Drive When Executed for Non(SCGCQ01095664
 -Tiger FPGA: 5002 Fault with tip code(SCGCQ01099808 
 -Fault 0x1901 is observed when an internal IO to a SES device fails.(SCGCQ01100151 
 -PL: SAS3416 Fault 0xD071 & D015 during the heavy I/O(SCGCQ01107033 
 -Marlin A0: Fault 0xEC30 while running NAKIncomingTLP(SCGCQ01109436
 -pl: device missing delay timer may expire too soon(SCGCQ01112033
 -PL: I/O could timeout if task management fails(SCGCQ01113324
 -Ventura: backend PCIe: add workaround for link recovery issue(SCGCQ01114258
 -Ventrua A0: PL fautl xD10F observed during SAS cable pull(SCGCQ01114603
 -Same slot number is seen for two NVMe drives with different dev handle(SCGCQ01118576
 -PL: Fault 0x5894 During System Power On(SCGCQ01120618
 -Ventura/Marlin: backend PCIe: need to toggle CfgClrDlInactive on link up always(SCGCQ01121263
 -Ventura: backend PCIe: do not disable delayed generation of DLLPs before Gen3 equalization(SCGCQ01122717
 -Marlin A0: 0xC010 fault during EEDP Initiator (SCGCQ01126480
 -Ventura: backend PCIe: need to perform PCIe related workaround for reasons other than the original issue(SCGCQ01126828)
 -Ventura B0: FPE SAS completion queue should be in ILR(SCGCQ01127400)
 -Ventura: HW/FW cycling needs to be dynamic to support A0 and B0(SCGCQ01133450 )
 -Ventura: Disable HW Workaround for SCGCQ00849789 for B0(SCGCQ01133505)
 -Ventura/Marlin: backend PCIe: work around a link down issue(SCGCQ01134422)
 -Fault xD060 seen when doing NVME glitching(SCGCQ01134928)
 -Ventura/Marlin: backend PCIe: start of day mem allocation with backend PCIe disabled(SCGCQ01136170)
 Marlin A0: Switch attached NVMe drives are not discovered from Build 73.(SCGCQ01138330)
 -pl: backend PCIe: direct attached NVMe device may go missing after a port glitch(SCGCQ01139383)
 -Ventura B0: 0xD024 fault running IO's with I/T setup(SCGCQ01139454)
 -SAS/SATA drives not discovered(SCGCQ01140463 )
 -PL: Hard/Link reset on HBA phy failing with IOCStatus = 0008 (Invalid State)(SCGCQ01146367 )
 -Direct attached SATA drives not discovered on phys associated with SAS core 1 (SCGCQ01147012)
 -Ventura/Marlin: backend PCIe: need modification to hot reset/link down workaround(SCGCQ01149992 )
 -Ventura/Marlin: backend PCIe: bad phy number used in link down workaround(SCGCQ01149994)
 -Ventura PL: IO Unit Control(SCGCQ01150524)
 -Ventura B0: Task Management errors with no exception while running IO's on I/T setup(SCGCQ01152173 )
 -Added new PL fault code and also set default 60 secs for SATA hinting timer in PL(SCGCQ01152796)
 -Marlin/Ventura: backend PCIe: various faults may occur if a link goes into recovery(SCGCQ01154122 )
 -pl: 265D fault when host booting firmware on a board with a blank flash(SCGCQ01154569 )
 -Drive slot Locate LED operation may incorrectly locate slots on Group ID supported backplanes(SCGCQ01162646)
 -Fault 0x670B seen while sending SCSI Read Buffer commands to bunch of SATA drives(SCGCQ01163838)
 -Virtual SES and DA Sep code use large amounts of stack(SCGCQ01164632)
 -PL: Usage of PL_LOGINFO_IOPI_MEMORY_MOVE_FAILURE results in invalid LogInfo being returned(SCGCQ01167339)
 -Ventura: Implement hardware workaround for SAS Training failure(SCGCQ01168045)
 -PL: Controller link does not come up after clearing phy disable flag in sas io unit page 1(SCGCQ01168258 )
 -Ventura: Incorrect Wide Port group LED data mapped for certain GPIOs(SCGCQ01170439)
 -Ventura/Marlin: NVMe: completion queue head doorbell may not be written in a couple of error cases(SCGCQ01170592)
 -Ventura/Marlin: NVMe: potential admin command timeout(SCGCQ01171130)
 -Host trace buffer does not contain expected data(SCGCQ01174473)
 -Starting Task Managements take a long time in certain conditions(SCGCQ01176191)
 -PL Fault 0xd073 is seen during certain IO load conditions(SCGCQ01180058)
 -pl: 4311 fault may occur when both SAS and NVMe are enabled(SCGCQ01186198 )
 -PL: 0x7C71 Fault During Repeated Phy Resets with Mixed SAS/SATA(SCGCQ01187303)
 -NVMe devices are not discovered with BAR Fail mode configured in Ext Mfg 44(SCGCQ01188761)
 -Ventura: backend PCIe: link recovery issues(SCGCQ01188928 )
 -Ventura: backend PCIe: NVMe devices may not show up in Windows(SCGCQ01192659)
 -Ventura: backend PCIe: link fails to come up on hot plug after device pull(SCGCQ01193756
 -PL: Fault 5814 while multipath SAS pull/push of 2 enclosures(SCGCQ01193764)
 -Ventura B0: Observed fault 0x4A00 during Phy glitch between HBA and Expander(SCGCQ01194893 )
 -Ventura: PL – PCIe Topology Polling incorrectly enabled (SCGCQ01194941)
 -Ventura B0: PL Fault 0x6001 for NVMe drives running Ios and random Task Managements(SCGCQ01196113 )
 -pl: Unexpected SAS link operation with protocol cycling enabled(SCGCQ01198352 )
 -Ventura: RxCtxMgr debug print is printing an un(SCGCQ01198393)
- PL: Incorrect phy resets(SCGCQ01199063)
- Ventura: backend PCIe: device add event is generated for a backend PCIe switch(SCGCQ01201813 )
- Ventura: backend PCIe: various issues may occur if multiple switches have the same Device Serial Number(SCGCQ01202401)
- PL: pl acm UART command displays old information when no cable is connected(SCGCQ01202502)
- Ventura B0: Expander goes missing when running port reduction between HBA and expander(SCGCQ01205651)
- Ventura: backend PCIe: switch attached NVMe devices fail to appear in OS after switch removal and add(SCGCQ01206629)
- IOs failed to host with generic open fail log info(SCGCQ01208362)
 -Fault 0xECA5 while running Stress IO's along with TMs & Fast path Enable/Disable(SCGCQ01208939)
- Ventura: backend PCIe: unable to print switch registers for debug(SCGCQ01209215)
- Ventura B0: MR FW is hitting a data abort crash during boot up and discovery(SCGCQ01210439)
- 0x670A Fault occurs while doing Port Reduction / Cable break testing(SCGCQ01210530)
- Ventura: Ring buffer print missing newline(SCGCQ01211776)
 -Ventura: backend PCIe: address pool configuration may fail in a boundary case(SCGCQ01211982)
- Ventura: PCIe Device unregister failure(SCGCQ01214268)
 -Ventura B0: PL Fault 0xD075 when re(SCGCQ01214275 )
 -Ventura B0: vSES target not getting exposed in Linux Host(SCGCQ01214419)
 - PH2 Pre-Alpha Ventura B0 - FreeBSD Driver - Eight Virtual SES entries are noted in camcontrol dev output(SCGCQ01214459 )
 -Ventura B0: pl status displays vSES for physically attached enclosures(SCGCQ01218944)
 -PL: Passthrough I/O could timeout if DST is placed in OCM(SCGCQ01219643)
- Ventura B0: vSES Target: RECEIVE DIAGNOSTIC SCSI Command in Not Failed With Expected Sense Data for Unsupported PAGE CODE(SCGCQ01220930)
 -Handle FPE IOP start queue full condition(SCGCQ01222231)
 -Ventura: backend PCIe: link recovery testing issues(SCGCQ01222761)
 -Diag Reset observed while sending TM to NVMe drives(SCGCQ01223373 )
 -Link/Hard reset IO Unit control message to a phy fails with IOC Status as invalid state.(SCGCQ01227486 )
 -PL Fault 0x6003 while powering off all the connected NVMe drives with IOs running(SCGCQ01228947)
 -Ventura B0: vSES firmware sending incorrect SCSI state while completing INQUIRY with UNDERRUN(SCGCQ01230819)
 -Ventura/Marlin: backend PCIe: build fails if a specific workaround is disabled(SCGCQ01232334)
 -Ventura/Marlin: backend PCIe: topology change event weirdness(SCGCQ01235263)
 -Ventura/Marlin: backend PCIe: target reset may time out if device is partially initialized(SCGCQ01235889)
 -Ventura/Marlin: backend PCIe: reset may not be sent to a device that is missing but present(SCGCQ01237022)
 -Ventura/Marlin: backend PCIe: EC09 or 501 fault may occur on IO error(SCGCQ01238032 )
 -Fault 0x6001 while running IOs and TMs to NVME drives with media errors.(SCGCQ01238263)
 -PCIe device page 0 field may not report devices link number(SCGCQ01239126)
 -Fault 0xe989 is seen if media errors are seen while running IOs to NVMe drives(SCGCQ01239353)
 -Data Protect Sense Key received on power up of NVME drive(SCGCQ01239795 )
 -Marlin B0: backend PCIe: enable a couple of workarounds(SCGCQ01240537)
 -Memory allocation of 5 NVME drives is required to discover 4 drives when VPP LED management support is enabled.(SCGCQ01240626)
 -Override NVMe support check for auto backplane detection to enable SGPIO(SCGCQ01240629 )
 -PL Fault 0000430b(SCGCQ01240774)
 -SAS Topology gets hung because of a firmware fault in sas3516 controller(SCGCQ01241342)
 -SSC Profile and PLL BW Selection(SCGCQ01243603)
 -Ventura B0: vSES Target: Incorrect Sense Data for REQUEST SENSE SCSI Command(SCGCQ01247631)
 -Ventura: Auto backplane detection (SCGCQ01247682)
 -pl: FPE timer may be activated for an IO that is being aborted(SCGCQ01249183)
 -PL fault 0xe989 hit with cable push/pull(SCGCQ01249805 )
 -Ventura B0: Fault 0x430B while running IOs & Hard resets of HBA Phys(SCGCQ01254319)
 -Commands after an ATA Passthrough ReadFPDMA queued command hang(SCGCQ01254357)
 -Ventura B0: Fault ec86 when Capella 2 switch with AHCI drives connected to controller(SCGCQ01254362)
 -Ventura B0: ACM : Active cables not powered on with Active cable power management enabled & threshold not hit(SCGCQ01255026)
 -pl: NVMe: D015 fault during Abort Task(SCGCQ01255908)
 -pl: backend PCIe: link failure after a hot reset is not detected by PL(SCGCQ01255930)
 -4K SATA block read error(SCGCQ01258955)
 -Ventura/Marlin: extra barrier in FPE firmware IO start path(SCGCQ01259570 )
 -Ventura/Marlin: backend PCIe: link not reinitialized after certain errors(SCGCQ01259639)
 -Marlin: backend PCIe: various faults occur when a backend PCIe link goes down(SCGCQ01261195)
 -Ventura B0: OS boot fails with latest HBA FW (02.250.02.00)(SCGCQ01261816)
 -SCSI commands issued to VSES may time out (SCGCQ01262672)
 -Ventura B0: (VSES) VSES Code cleanup(SCGCQ01264641)
 -Ventura B0: Miscellaneous vSES cleanup(SCGCQ01265824)
 -Fault 0xECA0 is hit while running IOs on NVMe drives behind Ventura(SCGCQ01266097)
 -Ventura/Marlin: backend PCIe: completion timeout disable support failure(SCGCQ01269306)
 -SAS3Ph3Alpha : NVMe drives are not getting detected in 9400(SCGCQ01276722)
 -IOMMU fault at address 0x80360000(SCGCQ01279547 )
 -pl: NVMe: CDB not printed when CDB validation fails(SCGCQ01281501)
 -Ventura/Marlin: backend PCIe: 265D, E5A2, or ECA0 faults may occur(SCGCQ01281505 )
 -Make platformtype function available to test utility(SCGCQ01282492)
 -FW goes to data abort when power cycle the enclosure.(SCGCQ01294834)
 -fw assert on Assertion failure in ../../mros/timer.c at line 196 when do cable pull or drive insert in 1st cycle.(SCGCQ01295869)
 -Implemented changes in persistence id allocation code to cover combination of up to 240 pds and 32 enclosures.(SCGCQ01297258)
 - MR-7.2: iMR 9440-8i:Hit MonTask line 662 in file ../../raid/mficmd.c rst=0 After Upgrade The Driver & Reboot The System(SCGCQ01299168)
 -Ventura: backend PCIe: EF53 fault on link down(SCGCQ01301079)
 -(NVME Only) Port enable completes before drive is detected by discovery.(SCGCQ01301777)
 -Disable firmware from flushing messages when it detects ld not unmap capable(SCGCQ01302478)
 -pl: NVMe: port enable times out if an NVMe device fails with CFS during NVMe init(SCGCQ01303837)
 -Ventura/Marlin: backend PCIe: potential unexpected EF50(SCGCQ01304678)
 -BST 7.3 (8GB) ==> Flash firmware and reboot post message showed "the maximum allowable limit of 3 enclosures"(SCGCQ013083570
 -14G:SWPT: Enclosure hotremoved and insert it back,one physical disk is missing in storage inventory.(SCGCQ01309090)
 -Overlapping Target Reset in Device Removal handling for multi path cause one of the device removal state machine to stall (SCGCQ01309469 )
 -[PL]While BGI running, reboot the system with 240LDs created, caused FW hitting DataAbortException montsk((SCGCQ01311291)
 -(SCGCQ01311300)
 - Ventura/Marlin: backend PCIe: EC56 fault on link glitch(SCGCQ013130750
 -Readjusted profile pd count to produce 240 PDs correctly(SCGCQ01315946)
 -Readjusted profile LD count to produce 240 VDs correctly (SCGCQ01315995 )
 -Due to a timing issue a hang condition may occur on cold power up(SCGCQ01316806 )
 -Consolidating CSETs from OEM stream to 7.1 Channel(SCGCQ01318925)
 -Consolidating a subset of CSETs from OEM stream to 7.1 stream(SCGCQ01318990)
 -Consolidating CSETs from OEM stream to 7.1 stream(SCGCQ01319003)
 -Consolidating CSETs from OEM stream to 7.1 stream(SCGCQ01319859)
 -CFGE- Page Read Current - SAS_IO_Unit not functional (SCGCQ01322101)
 -After a system reboot during BGI FW reports Consistency Check started instead of Background Initialization resumed(SCGCQ01324229 )
 -SCons: Doxygen Builder fails to keep track of dependencies(SCGCQ01326891)
 -MR(SCGCQ01326930)
 -Assertion failure in ../../raid/buffer.c at line 635: residualBytes==0 observed while BGI is under progress(SCGCQ01327188)
 -iMR(SCGCQ01328423)
 -PKG 465\ When a Migration starts fw eventually breaks(SCGCQ01329544)
 -Remove fw message "Clearing the led for pd: x" to make clear configuration cmd faster and less clutter in fw message output(SCGCQ01329994)
- Expander FW update fails with "The expander firmware update failed while downloading the firmware to controller" error(SCGCQ01330666)
 -Ventura: Task Management to NVMe drives may not complete(SCGCQ01330747 )
 -FW entered Exception mon_task while importing foreign PDs in loop.(SCGCQ01330764) 
 -Ventura FW is not reporting Underrun status for RW Ios in the legacy JBOD IO path(SCGCQ01331421)
 -iMR(SCGCQ01331455)
 -To close the window during which ONFI is not armed even when the data is dirty(SCGCQ01332552)
 -Fixed SAS cleanup code to skip the PCI device instances.(SCGCQ01332893)
 -MR7.3PA3: Storecli "show autopdcache" command blocks for 2min40sec during IO.(SCGCQ01332914
 -Montask after data abort exception handler was called(SCGCQ01335905)
 -Need interrupt to fire when OCM flush is complete(SCGCQ01336830)
 -Crusader: fw Assertion failure in ../../raid/ld.c at when insert pd(SCGCQ01337840)
 -FW enters an infinite loop of Exception Frame dumps if an exception is hit early boot(SCGCQ01338865 )
 -Handle underrun cases for STP reply for DISM(SCGCQ01338917)
 -fw hit cache.c when pull out NVMe pd in r0 to generated pinned cached.(SCGCQ01339902
 -High Frequency Smart Polling Disabled/ ROC temperature not udpated via OOB(SCGCQ01340066)
 -MR7.1 : MemsetECache prints fill important termlog space(SCGCQ01342196 )
 -FW502:Enclosure ID for the new PD inserted on system comes as 0xff(SCGCQ01342997)
 -Fix max patrol read drive in nvram(SCGCQ01344315)
 -Ventura: NVDATA option to ignore BP_TYPE check and force enable PCIe RefClk for NVMe backplanes(SCGCQ01349247)
 -FW not setting correct encl type and device ID for Insight(SCGCQ01349774)
 -Assertion failure in ../../dm/mpt2/mptDirect.c at line 1438: pMptRequest(SCGCQ01349932)
 -Reject firmware downgrade from 7.3 to 7.1 if active Profile is 11 (NVMe mode)(SCGCQ01349950)
 -Second Reconstruction starting but no progress(SCGCQ01351330)
 -MR_7.3_PA4 : Kill adpater observed , while creating R0 autoconfig when new drives are added to the system(SCGCQ01351674)
 -Insight drives are not always getting an enclosure ID(SCGCQ01351698)
 -MR7.3 Controller is not detected after running overnight cable pull(SCGCQ01352931)
 -Assertion failure in ../../raid/cache.c at line 7016 < !cache_is_dirty() >, while adding new drives when autopdcache is set as R0.(SCGCQ01356004)
 -WA for specific enclosure SES Command 0x1D(SCGCQ01356733)
 - Ventura MR 7.3 - Continuous prints of "C0:bypassWaitForBootMsgRetrieval: Waiting longer for boot message acknowledgement"(SCGCQ01357373)
 -MCTP workaround cannot be disabled(SCGCQ01358484)
 -MR7.3_FW:Assertion failure in ../../dm/mpt2/mptDirect.c ,while running multipath make/break and enclosure powercycle with IO(SCGCQ01359010)
 -Update PL version check(SCGCQ01360720)
 -System hangs at "Initializing FW Interfaces" with pinned cache present.(SCGCQ01361595 )
 -240VD with multipath connection ,drive management page doesn't list it properly(SCGCQ01375076)
 -Compatible profiles are not seen if enclosures with more slots are attached than supported by profile that needs to be displayed but compatible (SCGCQ01375264)
 -Data flush to drives after cache offload taking ~250 seconds.(SCGCQ01376296)
 -Context info is not cleared for each state, which can result in incorrect retry count for each state, resulting in drive dropping issue.(SCGCQ01378874)
 -Ventura MR 7.1 (SCGCQ01380062)
 -Bad drive causes system to hang on boot.(SCGCQ01381151)
 -Initiate ocr when FW enters MonTask(SCGCQ01381615)
 -Exception in accessing the c_ptr(SCGCQ01381732 )
 -Recursive call into allocWait() due to depleted MPT frame pool(SCGCQ01382543)
 -fw report more than 240 pd even controller connect less than 240 pds(SCGCQ01382851)
 - During OCR when recon is in progress, fw breaks due to exception.(SCGCQ01385063)
 -FW hangs when running a negative test case adding a 5th enclosre to one of the ports (SCGCQ01385667)
 -FW reports copy back started on SED/non(SCGCQ01387429)
 -Power glitch test (1sec +)FW broke into Megamon. EVT#Fatal firmware error: Line 939 in ../../cpu/arm/exceptions.c(SCGCQ01391376)
 -OCR causing date/time stamp to be inaccurate.(SCGCQ01391377)
 -Disks report incorrect rotational speeds(SCGCQ01391462)
 -Ventura Perf drop in SAS HDD R5 and R6 Seq. Write up to %24(SCGCQ01395996)
 -PL considers Timer Handle=0 and invalid, MR FW did not.(SCGCQ01399026)
 -Untested CSET related to tty logging flash changes went in: needs to be corrected(SCGCQ01399486)
 -MR FW: Enable RMC logging for OEM(SCGCQ01405061)
 -The Auto Config feature not present in HII(SCGCQ01406286)
 -)
 -MR 7.3: OCR is not enable by default for iMR(SCGCQ01406364)
 -Certain boards failed manufacturing screening due to Micron M83C(SCGCQ01407825)
 -Purley Server: CATERR reported on front panel LCD and SUT hang at the windows logo page(SCGCQ01410221)
 -(SCGCQ01411542)
 - MR7.3_Regression_Controller time is not picked up during bootup(SCGCQ01415608
- NVDATA: Change Default SGPIO electrical driving strength from 50 to 66 Ohm per HW team recommendation(SCGCQ01418180)
- H745MX controller hangs when Cryptographic erase operation performed on SATA SSD(SCGCQ01418745)
- Data abort exception during OCR with JBODs(SCGCQ01421427)
 -Non Data SATA FIS command fail if Passthrough flags and DMA(SCGCQ01423777)
 -Prepare ONFI Memlist to offload 8GB DDR region such that DDR size is uniformly distributed across ONFI devices(SCGCQ01428498)
 -MFCD incorrectly updated from MR ParaPage0 (SCGCQ01435763)
 -Constant print "phy 8 disabled" in tty log(SCGCQ01438991)
 -Pinned cache does not clear after discarding and server reboot(SCGCQ01442925)
 -Incorrect grammar in post message(SCGCQ01444273)
 -Check to enable Single COL Image support based on Dram size is not correct.(SCGCQ01445143 
 -Convert to HBA option is shown(SCGCQ01447834)
 -Can not change the profile back to "A" once you are in profile "B" and flash the controller to FW that does not support NVMe(SCGCQ01503509)
 -MR7.3.1 : controller reset seen while importing 32 VD foreign config(SCGCQ01506874)
 -SPV: Fault 0x0501 when drive is pulled.(SCGCQ00135004)
 -BT1680: pl: Unquiesce of TM doesn't restore subsystem id.(SCGCQ00140924)
 -Diag commands pl fpe mgrdsff and mgrdsfff didn't work, mgrds was exectuted instead(SCGCQ00144374 )
 -Gen3 TaskMgmt: x61A0 Fault After Starting 2nd TM to FPE Device(SCGCQ00145364 )
 -Fault D062(SCGCQ00145624)
 -when handling LD exceptions from Cuda, PL was not clearing FPE bit and FPEStatus(SCGCQ00146895)
 -ReadCapacity returning 0xFFFFFFFFFFFFFFF on a SATA drive reporting a 0 LBA count(SCGCQ00147027)
 -Fault 0xD091(SCGCQ00147076)
- 0xD023 fault while re(SCGCQ00147442)
- SATA Only: Fast path IOs to sata device fails(SCGCQ00147726)
- FPGA: Gen3 TaskMgmt: 0x1901 Fault On TM Completion(SCGCQ00147805)
- Device won't do Fast Path IO after hot plug/pull done (no IO running)(SCGCQ00147819)
- FPGA: Gen3 TaskMgmt: 0x6827 fault when cleaning up port layer errors-(SCGCQ00147864 )
-Dev State table mem alloc size should be PLI_MEMORY_MULTIPLIER_NUM_DE(SCGCQ00148155)
 -ICES_PLUS(SCGCQ00148214)
 -Fault xD091 seen while running IO(SCGCQ00150094)
 -Device add/remove testing results in a fault 0x6202.(SCGCQ00151026)
 -When devices are removed / added the I/Os hang.(SCGCQ00151027)
 -SEP device incorrectly getting marked as Fast Path Capable by device manager(SCGCQ00151367)
 -Task Management Target Reset to a SAS target running Fast Path IOs choking the IO test(SCGCQ00151370)
 -A fast path INVALID_DESCRIPTOR exception would be passed to IOP with incorrect status(SCGCQ00152230 )
 -SATA: IO Stuck while running TM to sata drive.(SCGCQ00154686)
 -EDFB DMAGroup not set properly(SCGCQ00155513)
 -EDFB tracking of used DMA Groups not working(SCGCQ00155516)
 -FPGA: Fault 5890 after drive pull in Linux while running Medusa Stress(SCGCQ00155628)
 -0x6700 Fault(SCGCQ00156772)
 -64 bit driver does not detect hot(SCGCQ00158328)
 -SAS3FW: pliGetFpeMidInfo returns the FPE flags wrongly.(SCGCQ00158479)
 -FPE: Fault 0x5802 While running FPE IOs to mixed SAS/SATA topology.(SCGCQ00159515)
- MisMatch TxFM initialization code was not in FPGA build(SCGCQ00163393)
- Fast path I/Os keep running even when force pend bit is set(SCGCQ00163610)
 -FPGA: Dynamic Queue Depth variations for SAS Targets broken for powers of 2(SCGCQ00163962)
 -Fault 0xd012 while using Cuda timer when timeout is set to less than 3 seconds(SCGCQ00165753)
 -Task Management Requests never complete(SCGCQ00167193)
 -FPGA:Fault 4C30 seen with SCSI(SCGCQ00168724)
 -Fault 0xD093 during an MUR while running Fast Path Ios(SCGCQ00168911 )
 -0x5831 Fault while running heavy write ios and internal TMs(SCGCQ00169027)
 -Task Management may cause an infinite loop when cleaning fpe exception queue.(SCGCQ00170684)
 -PL faults with fault code 0xd040 when we try to enable CUDA timer through NVDATA-(SCGCQ00171456)
 -PL register dump stops on specific Detroit Core register(SCGCQ00172083 )
 -Format unit progress indication is not being updated correctly(SCGCQ00172663)
 -FPGA: 0x5111 fault during Target Mode testing(SCGCQ00172991)
 -Build fails because of Small Data Area overflow(SCGCQ00176456) 
 -6001 Fault During IR RAID0 Volume Creation Under Linux SLES11(SCGCQ00177106)
 -We were indexing outside the buffer range.(SCGCQ00179631)
 -Gen3 FPGA: 0x4101 fault while Target Mode testing with TM scripts(SCGCQ00181715)
 -Phy link rate does not follow MaxMinLinkRate in sas io unit page 1(SCGCQ00187614 )
 -MidUsed should be set for IOs if IoFlags indicates completion to colt even if Reply Dest is not set(SCGCQ00187766)
 -IOs stop to sata drives(SCGCQ00188083)
 -Fault 0x5896(SCGCQ00188925 )
 -SAS3 firmware faults when an FPE checkpoint is masked(SCGCQ00194554)
 -6101 Fault while running Task Management Stress test(SCGCQ00194569)
 -Invader A0: Spinup Delay ignored on port 0(SCGCQ00197619)
 -Invader A0: phys not coming up after being disabled and then re(SCGCQ00198822)
 -MR IOP did not get timeout notification for IO started by PL firmware when jammer was used to block response frames(SCGCQ00199049 )
 -Invader A0: Qdepth not decrementing on Task Set Full(SCGCQ00200268)
 -The "CurrentStatus" field in SAS IO Unit Page 6 is not getting updated properly when Port width modulation is disabled.(SCGCQ00201411)
- Invader A0: D100 fault while running stress using Write/Read (6) CDB size to a SATA NON(SCGCQ00202551)
- Drives do not link up reliably(SCGCQ00205778)
- Invader A0(SCGCQ00207040)
- Invader A0: When running 1MB I/Os to a Target Mode Invader a fault occurs.-(SCGCQ00207148)
 -Region lock release hangs due to AVL tree corruption(SCGCQ00208241)
 -Gen3: PM (SCGCQ00208458 )
 -Fault d012 due to FPE timer error while running stress loads(SCGCQ00209193) 
- Gen3: PwrMgmt - SATA Devices not showing up in Discovery(SCGCQ00209549 )
 -Invader A0: 5897 fault while glitching the whole port between the first 2 expanders(SCGCQ00210117)
 - Non-TARGET mode builds wouldn't compile(SCGCQ00210303 )
 -System DMA error not causing a firmware fault(SCGCQ00213368)
 -Invader A0: Fault 265D while running Block Move and Task Management Test(SCGCQ00217049)
 -Invader A0: 0xC009 fault on Target side of 12G setup(SCGCQ00217481)
 -Invader: Updated the FW work around tables for the B0 release.(SCGCQ00218436)
 -fault D025 while running IOs on a mix of SAS and SATA drives(SCGCQ00218687)
 -Invader A0: Program RxEEDP correctlyt for non good response handling(SCGCQ00218697)
 -Invalid 0x5897 and 0x6828 faults(SCGCQ00218792)
 -0x5841 while doing single Phy cable breaks for 1 second(SCGCQ00219298)
 -Invader A0 (SCGCQ00219408)
 -Fault 0xD07B seen during enclosure pull(SCGCQ00220676 )
 -TxFM cleanup does not clear all possible interrupts after cleanup.(SCGCQ00221800)
 -Workaround for LMIDs in exception queue having wrong VF_IDs(SCGCQ00222933)
 -PL hits TLB error while dumping SGLs(SCGCQ00223497 )
 -SMP command DISCOVER LIST fails with a timeout occasionaly. (SCGCQ00224795)
 -Fix fault when the trace buffer mode is changed.(SCGCQ00224807)
 -Invader A0: 0x583B fault during IO and Task Management in CM(SCGCQ00225189)
 -Invader A0 (init/targ): 0x7c54 fault during stress and cable breaks(SCGCQ00225813 )
 -Fault x6018(SCGCQ00225835)
 -Invader A0: Frame Length Mismatch during a read IO.-(SCGCQ00227400)
 -Fault 0x5302(SCGCQ00228348)
 -(SCGCQ00228765)
-Invader A0: CM looses devices during whole port glitches(SCGCQ00228959)
- Invader A0: 0x4A00 fault while running whole port cable glitches during stress(SCGCQ00229141)
- D072 Fault(SCGCQ00229676)
- Invader PL CLI show expander prints incomplete information(SCGCQ00235365)
- Gen3: PwrMgmt (SCGCQ00235403)
- After a device may send out an OAF with a rate value of 0x00(SCGCQ00239383)
 -Invader PL: 0x265D double fault when faulting before FPE register initialization(SCGCQ00241036)
 -Fault 0x2667 when trying to register a diag trace a second time (SCGCQ00242016)
 -0x510E fault while running CM BlockMove(SCGCQ00242069)
 -CLI command pl dbg or pl reg all causes 0x265D fault(SCGCQ00242162)
 -Fault x5814 while running Initiator and Target mode IO with another controller also doing Initiator and Target mode.(SCGCQ00244719)
 -Fault 0x583E seen running SATA IO with cable glitching(SCGCQ00246442)
 -WD SiliconEdge Blue SSD not discovered by adapter(SCGCQ00250990)
 -A region of greater than 3 can cause reading and writing to registers outside the snoop registers.( SCGCQ00253267)
 -Command Transmitting error fro OPEN FAILED cases doesn't work in out of resource cases.(SCGCQ00254943)
 -D024 or D025 fault seen when using FPE checkpoints to debug(SCGCQ00255192)
 -Fault 0x4A00 during cable breaking or drive pulls(SCGCQ00259575)
 -PL: Need to have unique fault codes(SCGCQ00263726)
 -Invader B0 was using high initial AWT values(SCGCQ00268857)
 -Invader A0 TxDMA cleanup code needed a change added back(SCGCQ00278781)
 -Invader B0: Adjust SAS Max Qdepth at init to account for Hw Limitations.(SCGCQ00282258)
 -TBM Extended Mode (PLI_TBM_BUFFER_ADDR_LOC_PLB not supported)(SCGCQ00282507)
 -Invader will reset ATAPI SEP Continuously while sending a command with inbound data(SCGCQ00289355)
 -ATAPI Request Sense Command failing(SCGCQ00290668)
 -Fault 6108 used in multiple places. (SCGCQ00291410)
 -WriteBuffer in 'Write Data' mode executes with good status when Bufferid=0 & Param List length != 512.(SCGCQ00297375 )
 -Fury B0: 0x4a00 Fault Running Cobra Expander Resets(SCGCQ00298630)
 -Invader B0: 0xD023 fault when BIOS searching for devices(SCGCQ00299563)
 -Invader B0: Controller links up at 3Gbps even when minimum link rate specified is set to 12Gbps(SCGCQ00314388)
 -PL Fault 0x6B0C when performing PHY power management(SCGCQ00318960)
 -Invader B0: (PL) Fault xD072 during I/T switching with IO and TM(SCGCQ00328713)
 -Fixed Problem in Target Mode Code Which Caused 0x26B5 fault(SCGCQ00336232)
 -Invader B0: Fixed Problem in DMA Queue via Hardware Workaround(SCGCQ00336429)
 -Invader: Fixed Debug Print in Port Layer(SCGCQ00336882)
 -PCIE lockup occurs when running EDFB IO with cable breaks and device removals(SCGCQ00337231)
 -Tape drive [3Gb/sec SAS] not detected with Invader controller(SCGCQ00338996)
 -Workaround to fix fault 0x4A00 failed to run in certain circumstances(SCGCQ00340547 )
 -Enable the new PCIe device translation block(SCGCQ00349889)
 -Combined error handling for PCIe devices(SCGCQ00360964)
 -Assertion while enabling MSIx interrupts(SCGCQ00362633)
 -Stang admin interrupt handler doesn't check IntStatus_IoComplete(SCGCQ00374668)
 -Backend PCI enumeration tweaks(SCGCQ00379303 )
 -(CUDA) Cuda writes zero to the reply descriptor post FIFO on completion(SCGCQ00386306)
 -Remove workaround for [Dauntless]264(SCGCQ00386627)
 -PCIE IO Unit 0/1 size in header is not correct(SCGCQ00394558)
 -No functional change(SCGCQ00395325)
 -Dauntless Firebird header file typos(SCGCQ00397598)
 -Several issues related to exception/error handling for NVMe devices(SCGCQ00397632)
 -Bad memory access when doing first AHCI IO(SCGCQ00400538)
 -PCIe discovery doesn't work for AHCI behind PCIe switch(SCGCQ00412140)
 -IO timeouts with AHCI devices(SCGCQ00412147)
 -NVMe: Nonzero SkipCount doesn't work very well(SCGCQ00412150)
 -AHCI: Write and verify 32(SCGCQ00414013)
 -CEC Interrupt Enable register has no interrupt bits enabled(SCGCQ00419454 )
 -AHCI: TLB error/265D fault on write and verify command with complex SGL(SCGCQ00420902 )
 -Dauntless FPGA: Data Corruption reported when running 1M IO to AHCI device(SCGCQ00424263)
 -No access to DDR for backend PCIe devices(SCGCQ00426529)
 -SATA IOs larger than 255 sectors fail(SCGCQ00426959)
 -FW might fault with D004 running IO with Abort Task TM to AHCI device(SCGCQ00435380)
 -NVMe: Admin queue doorbell writes should be 32 bits(SCGCQ00438982 )
 -AHCI: MODE SENSE command fails with protocol error for some AHCI endpoints (SCGCQ00439935)
 -Debug only: SGL print aborts early(SCGCQ00441271)
 -Assertion failed: ..\..\pl\PciDevice/plPciSglTranslate.c, line 1941 for chained SGL(SCGCQ00443783)
 -PL Init Unnecessarily Zeros Memory(SCGCQ00447799)
 -AHCI: Command timeout with mixed auto and nonauto IOs(SCGCQ00448191)
 -PL translated read or write IO to a backend PCIe device times out(SCGCQ00448640)
 -FW might fault D065 fault when running IOs + Query task to AHCI device(SCGCQ00449578 )
 -Dauntless FPGA PDB PIM alignment issue(SCGCQ00449934)
 -PLB PIM3 internal address and PCI address mapping not maintained properly in firmware(SCGCQ00450497 )
 -Fault 0xd10f is seen as timer is not cleared for read/write PCIe IO(SCGCQ00454161)
 -AHCI Debug: changed how CCS value is read(SCGCQ00455697 )
 -AHCI: 60D fault on completion of a Write Verify command(SCGCQ00456311)
 -AHCI: Non-read/write IO is timed out(SCGCQ00457590 )
 -Dauntless FPGA: Fault 26B5 when running pl reg rxdpbuf from uart(SCGCQ00460919)
 -PL Hangs in Spinup Retry Request Entry function if 2 AHCI and a SAS devices are connected(SCGCQ00464397 )
 -D20C fault when starting CM Block Move with Diagnostic Buffer Posted(SCGCQ00465468)
 -SATA passthrough issued during FW translated AHCI IO results in 265D fault(SCGCQ00468027)
 -PCIe Device Page 2 header read always fails(SCGCQ00470746)
 -CM fails to detect a switch attached NVMe device(SCGCQ00479121)
 -Build fails when PL_FEATURE_PCI_DEVICE_SUPPORT macro disabled(SCGCQ00481604 )
 -PL did not clean up resources for internal AHCI encapsulated frame if associated SATA passthrough command failed.(SCGCQ00481908)
 -IO timeouts or D071 fault during task management with backend AHCI device(SCGCQ00484044)
 -Dauntless FPGA: D300 fault running IO and TM(SCGCQ00490962 )
 -NVMe: D300 fault with high queue depth PL translated read/write IOs(SCGCQ00498178 )
 -E002 fault occurs during AHCI task management(SCGCQ00505719)
 -Intermittent 265D fault on read of PCIe Device Page 0 associated with a phy(SCGCQ00518205)
 -IO timeouts occur after task management(SCGCQ00524964)
 -NVMe: fix a couple of async event handling issues(SCGCQ00556769)
 -NVMe: Write Buffer (mode 0x5) translation fails to complete(SCGCQ00557073)
 -Dauntless: Backend POM Window size should be aligned to number of PCIe devices supported(SCGCQ00558089)
 -(SCGCQ00590504)
 -NVMe: no call from TM during init idle wait (SCGCQ00595468)
 -(Sata Only) Sending 'Ata Passthrough' SCSI command with ATA Command as 'Read Verify Sectors' sometimes results in check condition response.(SCGCQ00597647)
 -NVMe: handling of admin queue full condition during NVMe async event handling(SCGCQ00600515)
 -With PL_FEATURE_PCI_DEVICE_SUPPORT disabled, improper MPI status sent back to config Requests(SCGCQ00613854)
 -NVMe: 6001 fault with NVMe init ready wait plus TM(SCGCQ00630682)
 -26B5 fault on backend PCIe link down(SCGCQ00640436)
 -DCR Read/Write functions in PL had an extra layer define being used to access that was not needed.(SCGCQ00660424)
 -NVMe: remove READ BUFFER translation(SCGCQ00663643)
 -NVMe: no retry if initial NVMe init fails(SCGCQ00664181)
 -iop show diag fails to clear ring buffer(SCGCQ00669672)
 -Fault 0x6230 seen when sending Port Enable(SCGCQ00670926)
 -4308 fault when using SAS IO Unit Control message with SEND PRIMITIVE operation(SCGCQ00673188)
 -Intruder: Fault 0x4308 during SMP time out(SCGCQ00677699)
 -(All SAS/SATA products) Fault 0x670A seen on TM testing(SCGCQ00682695)
 -PL: Fault 0x6004(SCGCQ00682898 )
 -NVMe: incorrect buffer offset used in Write Buffer translation(SCGCQ00683319)
 -PL: Fault 0x6001(SCGCQ00685967)
 -Dauntless FPGA: IOs timeout when running Medusa IO with abort task/abort task set TM(SCGCQ00689862)
 -IO UNIT control message replies with 'devhandle 0'(SCGCQ00692114)
 -Fault 0x670A running IO and Task Management (SCGCQ00693854 )
 -Fault x6001 running IO with Task Management(SCGCQ00693865)
 -PL: 0x6003 fault(SCGCQ00694271 )
 -Firmware Fault 0xEF00 seen while running Task Management and IOs to AHCI drives.(SCGCQ00695559)
 -EF04 fault running Random TM with Mixed IO sizes(SCGCQ00696962 )
 -Intruder FPGA: Destructive Domain (Bobcat's) hit fault 0xD0E0(SCGCQ00696975)
 -Ventura: Need required external defines and header file ordering to include SCS FW libs in IOP(SCGCQ00697063)
 -Intruder: Fault 0x265d while doing Port Enable(SCGCQ00702696)
 -PL NVMe (Ventura) IOCStatus SCSI Task Management Failed when running Abort Task to NVMe(SCGCQ00710213)
 -Dauntless FPGA: E5A1 fault running Medusa IO and abort task set TM to NVMe drive(SCGCQ00710238)
 -Intruder: Fix issues in FW controlled spinup(SCGCQ00710609 )
 -Intruder FPGA: Drives attached to expanders gradually get dropped during Task Management test(SCGCQ00715652)
 -Removal of unnecessary debug prints incase of spinup interrupt(SCGCQ00716758)
 -Ventura: PL memory allocation does not allocate DevHandles for PCIe devices(SCGCQ00716790)
 -Ventura: IOA Local RAM requires an offset(SCGCQ00717129)
-Fault 0x265D(SCGCQ00719768))
- Fault 0x6003 while running stress to 7 cascaded expander topology on Core 0(SCGCQ00723375)
 --Target Mode (SCGCQ00724470)
 -Ventura: Drives on link 1 always respond with sense data 020411(SCGCQ00725112)
 -Fixed Known Issues with FIS Port SCSI Unmap Translation(SCGCQ00728088)
 -Ventura: Small Data Area overflow in compile/link operation(SCGCQ00735463)
 -Fault 0xE00B while running mixed IO sizes with random task managements.(SCGCQ00736592)
 -Intruder FPGA: Fault 0x584F while initializing PL(SCGCQ00738149)
 -Intruder FPGA: Fault 0x584F while running Initiator Mode SMP Protocol Error HandlingSCGCQ00754410)
 -Intruder FPGA: Drive loss due to stuck TxDMA. (SCGCQ00754417)
 -(AHCI Only) Inquiry command to AHCI Sata drives fails(SCGCQ00758599)
 -Intruder FPGA: 0x6001 Fault while cleaning up an unconfirmed response frame during Task Management(SCGCQ00759399)
 -Backend PCIe: periodic dev init state check shouldn't run if init isn't running(SCGCQ00760618 )
 -Dauntless FPGA: IOs stop in while running task managements to AHCI device(SCGCQ00764902)
 -Intruder FPGA: Repeated SMP timeouts while running Io Stress to a mixed SAS/SATA topology behind cascaded expanders(SCGCQ00767624)
 -Dauntless: 265D fault on port enable(SCGCQ00768567)
 -AHCI: init breaks on device register access failure(SCGCQ00773059)
 -Intruder FPGA: Fault 0x670A on Target Controller during Block Move and Task Management Test(SCGCQ00776306)
 -Fault 61A5 during system initialization(SCGCQ00783705)
 -Incorrect use of variables in clear(SCGCQ00791142 )
 -Intruder: Implement Hardware Workaround for Minor Link Layer Issue(SCGCQ00795985 )
 -Intruder FPGA: Fault 0x4307 while running Block Move to drives and resetting random expander(SCGCQ00800919)
 -Backend PCIe: EC0F or D065 faults during PCIe task management(SCGCQ00804044)
 -Intruder FPGA: Add code to validate SASCore Number from chip phy number back in(SCGCQ00804129)
 -Ventura (SCGCQ00805411)
 -Fault 0x4330 when running non automated IO to SATA/AHCI/NVME devices(SCGCQ00818397)
 -Ventura: PCIe Device Manager DMD expiration handling(SCGCQ00824724)
 -Ventura: Only 1 drive is discovered when 2 sas or 2 sata drives are directly attached(SCGCQ00828878)
 -Dauntless FPGA: Misc AHCI tag allocation/count fixes for non(SCGCQ00836056)
 -PL: D304 fault while running Task Management test(SCGCQ00839498 )
 -PL: Assert was using compiled out code causing bad ring buffer(SCGCQ00839583)
 -Ventura: backend PCIe: some bringup changes(SCGCQ00841065)
 -Intruder A0: Fault 0x5854 during I/T Switching(SCGCQ00843939)
 -Intruder A0: Fault 670A while running target mode Jammer exception Test(SCGCQ00845803)
 -Intruder A0: 0x6C02 fault while running IO's and power glitching on every core(SCGCQ00846661 )
 -Ventura: backend PCIe: command issued prior to first AHCI init success may fail to unpend(SCGCQ00848265)
 -Ventura FPGA: Fault 6001 soon after initializationSCGCQ00851724)
 -Ventura FPGA: backend PCIe: data corruption seen during write/read/compare test(SCGCQ00851725 )
 -SAS3.5FW has tabs in source code(SCGCQ00852767)
 -Ventura: IFAULT_PL_LOW_INT_SPURIOUS (0x6C03) Observed(SCGCQ00854241)
 -SPL(SCGCQ00854245)
 -PL: Incorrect SGPIO Index calculated for more than 2 SGPIOs(SCGCQ00855007 )
 -Ventura: IFAULT_PL_HIGH_INT_SPURIOUS fault (0x6C02) asserted(SCGCQ00855711)
 -Ventura: modify some debug info(SCGCQ00856678)
 -Ventura: PCIe device handle allocation starts at min handle plus one. (SCGCQ00856701)
 -PL (SCGCQ00859820)
 -Ventura: backend PCIe: modify IOP resource alignment code so that size is aligned also(SCGCQ00859837)
 -Fault 0xEC60 starting IO(SCGCQ00860763)
 -Rearrange PDB RCC interrupt handlers to avoid spurious interrupts(SCGCQ00862058)
 -Ventura: backend PCIe: PL translated PCIe read/write IOs may time out (SCGCQ00869263)
 -Two constants identified as containing old values.(SCGCQ00870618 )
 -PL: Enclosure Management bounds checking(SCGCQ00870903)
 -PL: Fix Out of Bound Array Access in Diagnostic Command code(SCGCQ00871318)
 -PL: Resize PL_TRANSNUM_UNUSED Define to 8 bits(SCGCQ00871678)
 -PL: Remove unused variable in a firmware function(SCGCQ00871686)
 -PL: Remove unused variable from the TRIM command handler(SCGCQ00871688)
 -SATL: Get Rid of Unnecessary/Duplicate Assignment Statements in SATL Function(SCGCQ00872849)
 -Ventura FPGA: 0xEC9D during PCIe task management(SCGCQ00872879)
 --Ventura: Fault 0xd024 is seen sometimes during link glitch testing(SCGCQ00874912
 -Ventura: backend PCIe: IOs to an AHCI device may halt after TM(SCGCQ00876257)
 -PL initializes IOA Local RAM with 0s without IOP FW knowing(SCGCQ00877473)
 -Timer Overflow errors for IOs sent using pliLightStartScsiIo(SCGCQ00880811)
 -Ventura FPGA: Fault EC30 fault followed by fault EC70 on full port cable break against an NVMe drive(SCGCQ00882972 )
 -Ventura: unexpected behavior may occur during PL init with non (SCGCQ00887074)
 -Ventura FPGA: TM to devices behind switch failing(SCGCQ00895687)
 -(AHCI ONLY) 0xE015 fault when bringing AHCI drive online in Windows OS(SCGCQ00896563)
 -Ventura: backend PCIe: various issues involving NVMe task management(SCGCQ00897148)
 -pl: IT: some debug prints go missing when a trace buffer is posted(SCGCQ00901424)
 -Remove Random number generator feature.(SCGCQ00904420 )
 -BL: Tiger bootloader is locking up and causing aborts(SCGCQ00910746)
 -Ventura: Dauntless min build fails with GPIO wide port group mapping changes(SCGCQ00923022)
 -Ventura: Sas phys are not linking up(SCGCQ00927730 )
 -PL: Optimize Start pending I/O function to gain a few % of IOPS increase(SCGCQ00929765)
 -PL: Fix arm compiler error.(SCGCQ00931355)
 -Tiger: PSB PEX registers mapped to incorrect AXI addresses.(SCGCQ00937890)
 -Tiger: CE and FxCore init issues(SCGCQ00943870)
 -Ventura: backend PCIe: 6001 fault on target reset with encapsulated requests outstanding(SCGCQ00952596)
 -Ventura: Fault 4308 when firmware cycle mode enabled(SCGCQ00953736)
 -Ventura: backend PCIe: fix some config page related bugs (SCGCQ00954691)
 -Ventura: backend PCIe: NVMe devices or PCIe switches intermittently fail to link up(SCGCQ00987792 )
 -Ventura: Second Sas and CSW cores are powered up when they don't exist(SCGCQ00987847)
 -Ventura: backend PCIe: need to reject an NVMe device with PI or metadata enabled(SCGCQ00991188)
 -Ventura: SAS devices are not discovered when hot plugged.(SCGCQ00991441 )
 -Fault 0x5841 due to Check Condition on Atapi Device(SCGCQ00994935)
 -Ventura: backend PCIe: SAS IO Unit Page 1 write causes NVMe devices to go away(SCGCQ00998568)
 -Ventura A0: 265D fault when running Destructive Domain test(SCGCQ01000117)
 -Ventura: Fix typo in register definition name(SCGCQ01002334 )
 -IOP submitted IOs to PL might inadvertently comlete to Host(SCGCQ01002364)
 -Tiger PL: Host port config space automatically sets BusMaster and MemSpaceEn(SCGCQ01002370)
 -Tiger: MPT Endpoint needs to be enabled before any register of the MPT endpoint is written(SCGCQ01004271)
 -PL: Devices removed if PCIe Extended Capabilities are not implemented(SCGCQ01005270)
 -PL: Tiger: Memory corruption when PL calls function to retrieve PCIe link speed and width (SCGCQ01007019 )
 -Fault 0xD102 is observed when incorrectly composed SCSI Write Buffer command is issued to a SATA drive(SCGCQ01008776)
 -PL: Link Reset prints are not disabled when Link Reset mask is cleared(SCGCQ01013716)
 -Tiger: TLPs from NVMe drives have incorrect requester ID on egress at host port(SCGCQ01015401)
 -(Sata Only) WRITE AND VERIFY SCSI Command Not Failed With CC for LOGICAL BLOCK ADDRESS OUT OF RANGE Condition(SCGCQ01015401)
 -Tiger Ventura: hardcoded devhandle translation needed removed(SCGCQ01018537)
 -Fault 0xEC69 observed while running mix of IO and task management tests on NVMe devices. (SCGCQ01018961)
 -Tiger FPGA: Fault 0xEE18 while initializing Ventura Tiger attached to a Tiger FPGA with a DA SAS drive (SCGCQ01019218 )
 -Tiger FPGA: Fault 0xED07 with tip while running PCIe link configuration at Start of Day(SCGCQ01021849)
 -Tiger PL: Fault 265D when configuring the backend PCIe(SCGCQ01024192 )
 -Ventura PL: Device handle pre(SCGCQ01024765)
 -Ventura A0: IOs stop while randomly sending a reset to single SATA device every 10 sec(SCGCQ01028113 )
 -PL: Fault code 0xD091 is in multiple locations(SCGCQ01029667 )
 -Fault 0xD025 is seen while running PCIe cable break test with IO test(SCGCQ01033270)
 -Ventura: backend PCIe: fix a few issues encountered upon surprise removal of a PCIe switch(SCGCQ01034082)
 -Ventura A0: EC60 Fault when Cables Moved on Ventura(SCGCQ01034096)
 -Ventura: Total pendcount incorrect for NVMe(SCGCQ01035858)
 -PL: FORMAT UNIT command sent to NVMe drive fails when FMTDATA bit is set to 1(SCGCQ01036201)
 -Ventura: backend PCIe: 265D fault on 'pl dbg' in some NVMe device rejection cases(SCGCQ01038453 )
 -Ventura: NVMe and non(SCGCQ01039059)
 -Tiger FPGA: Fault 265D is seen during IO and TM on SAS/SATA behind expander and IO on direct attached NVMe(SCGCQ01040974 )
 -PL: Some unhandled IOA interrupts were falsely generating spurious interrupt fault code(SCGCQ01043930)
 -Cannot read data from switch attached NVMe disk in legacy BIOS.(SCGCQ01044039 )
 -Tiger: Implement workaround for PSB failure to transmit message TLPs(SCGCQ01044060)
 -(SCGCQ01044463)
 -Ventura Tiger: Set default TM timeout to 6 sec for SED attached end devices( SCGCQ01045628)
 -Ventura: backend PCIe: miscompare may occur after link glitch between HBA and PCIe switch(SCGCQ01046343 )
 -Tiger: IO timeout seen when running IO with Query Task TMs(SCGCQ01047487)
 -PL: Mid reuse may cause data miscompare(SCGCQ01047691)
 -Ventura: backend PCIe: issues related to backend PCIe link handling and NVMe TM(SCGCQ01052703)
 -Persistent Connection Timeouts Occur With Some Drives(SCGCQ01057572)
 -Fault 0x1D02 while running port break between HBA and PCIe Switch(SCGCQ01058662)
 -Ventura A0: NVMe device isn’t getting reconfigured even though discovery runs and appears to find it(SCGCQ01058974)
 -FW entered PL Fault 0000d0d1 while I/Oing across LDs(SCGCQ01059682)
 -Tiger FPGA: Task Management to an NVMe drive causes the drive to drop off(SCGCQ01065218)
 -Ventura A0: NVMe init cmd timeout insufficient (SCGCQ01066004)
 -Ventura: NVMe: ARRE Bit Not Set to 1b in Read(SCGCQ01069374)
 -Ventura IOP: Fault 0x430B when removing a SED attached drive(SCGCQ01079206)
 -ARM abort due to stack corruption(SCGCQ01084201 )
 -Tiger: Periodic DPC check renders ringbuffer useless(SCGCQ01088685)
 -Coverity defect : Dead code due to repeated comparison(SCGCQ01089362)
 -PL: Some configuration pages return non(SCGCQ01092041)
 -Fault 0x430B observed while running IO and port glitch test between Marlin A0 and attached expander.(SCGCQ01093757 )
 -Tiger FPGA: Fix PCIe Io Unit Page 0 Read handler(SCGCQ01095060)
 -Marlin A0: Port glitch or lane break between HBA and PCIe Switch causes NVMe drive to go missing(SCGCQ01109425)
 -PL Light IO completes on Core 0 after getting FPE DISABLED Exception(SCGCQ01118902)
 -Fault 0x1900 hit when IOs and Task Abort Task management requests are run on the NVMe device(SCGCQ01122538)
 -Ventura: backend PCIe: IO timeouts may occur with NVMe devices under Linux(SCGCQ01134727)
 -Ventura B0: Misc active cable management fixes(SCGCQ01137484)
 -Ventura A0: Not all slots are enumerated with SIO group ID for odd/even PHY connector lane routing(SCGCQ01138057)
 -Ventura/Marlin: backend PCIe: reliability of link bandwidth change notification(SCGCQ01138343)
 -PL: Data abort exception while pulling JBOD(SCGCQ01138634)
 -pl: 265D fault if PDBs are unmapped with backend PCIe support disabled(SCGCQ01147668 )
 -PL: Incorrect LogInfo may be returned during handling FPE Exception IO(SCGCQ01165427 )
 -Virtual SES support can cause Fault 0x7200(SCGCQ01171097)
 -Enclosure Management: SES Staus Element Fails to Match a Valid ManPage14 Entry(SCGCQ01181308)
 -pl: delay loop may have twice the expected duration(SCGCQ011925710
 -Ventura PL: (NVMe) Fault 0x6004 while completing a Task Management due to unaccounted for Diverted IOs.(SCGCQ01196103)
 -Ventura: backend PCIe: various faults may occur after a link disturbance(SCGCQ01206536)
 -Ventura (Sata Only ) : Internal Device Resets observed on SATA Drives during I/O.(SCGCQ01207972)
 -Ventura B0: BTL is not assigned to expander(SCGCQ01211588)
 -Fix issues wit ttyLogToFlash=1 setting during task mgmt(SCGCQ01213091)
 -modified behavior of DCMD to return negotiated link speed for intel only.(SCGCQ01213413 )
 -Validate mid in Tx openfail cleanup(SCGCQ01215592 )
 -0xEC84 Fault observed when PCIe switch is Powered OFF and Powered ON(SCGCQ01216678)
 -PL Fault 0xEC07 found while Push/Pull of JBOD with IO's(SCGCQ01217170)
 -Intruder compile error in plVirtualSes.c(SCGCQ01219448 )
 -Ventura: NVMe devices not discovered with auto backplane detect RefClk enabled on VPP PCIe x4 backplane(SCGCQ01219537)
 -PL Fault 0xD368 seen due to POM windows not properly aligned(SCGCQ01222147)
 -GPIO HD Cable management function does not support active high level.SCGCQ01231609 )
 -FPGA Compile Error (SCGCQ01233994 )
 -Ventura/Marlin: backend PCIe: switch resources may remain allocated after it is removed(SCGCQ01235267)
 -pl: NVMe: Abort Task may abort an IO when it is still outstanding at the device(SCGCQ01235948)
 -NVMe drive doesn't come up with new firmware after SCSI Write Buffer is issued with mode Download Microcode, save and activate (mode 5)(SCGCQ01237245)
 -PL PCIe Discovery events are broadcasted with an invalid data((SCGCQ01241985)
 -pl: NVMe: fix a couple of issues exposed by a malfunctioning device(SCGCQ01243546)
 -Fault 0xD073 with IOs to NVME drives with media errors.(SCGCQ01249813)
 -Fault 0x265D while powering on/off the attached PCIe switch devices.(SCGCQ01251456)
 -Marlin: Add additional support for cold boot fix (SCGCQ01251641)
 -IO Timeout while sending Task Managements to PCIe devices(SCGCQ01256214)
 -pl: task management may not complete with heavy IO load(SCGCQ01258861) 
 -VSES diag page 0A mapping not enabled for NVMe devices(SCGCQ01261033)
 -Ventura: Slot status LED updates fails with mixed backplane types (VPP and SGPIO) in the same server config-(SCGCQ01266429)
 -Ventura B0: vSES Target: INQUIRY SCSI Command in Not Failed With Expected Sense Data for Non(SCGCQ01269854)
 -Fault 0xD372 is seen during NVMe IO run and drive push pull test(SCGCQ01271759)
 -Ventura/Marlin: backend PCIe: NVMe devices aren't discovered with VSES disabled(SCGCQ01274107)
 -Data loss during cache offload power cycle test(SCGCQ01286491)
 -pl: excessive exception generation during SATA IOs with Task Set Full handling disabled(SCGCQ01291127)
 -73: FW hit pl6101 when single glitch COL(SCGCQ01295065 )
 -Enclosure ID changes when a cable pull and insert occurs.(SCGCQ01295290)
 -Ventura controller fail with diagnostic(SCGCQ01300633)
 -pl: NVMe: EC0F fault occurs during task management(SCGCQ01303943)
 -MR7.1: Unexpected event for lun not ready Sense: 2/04/02(SCGCQ01304550)
 -Modify CSW initialization(SCGCQ01306944)
 -Disable SATA FIS poritng on a SATA drive connected to a Broadcom expander with EDFB enabled.(SCGCQ01307008 )
 -Added Profile 0xD (SCGCQ01307054)
 -Handle 240 PD & VD Code Review AIs in 7.3 firmware(SCGCQ01308532)
 -Remove HDD from backplane always remain green light with internal adapter(SCGCQ01309087)
 -B-ST 7.3 (4 GB Profile 12)==>SCGCQ01082693 Verify support Raid level firmware hit Montask ..arm/exceptions.c(SCGCQ01310247)
 -Incorrect DmDevSMPReady array size(SCGCQ01310496)
 -Due to a timing issue a hang condition may occur on cold power up(SCGCQ01311156)
 -Update PL version check for PL version assert for OEM(SCGCQ01313019)
 -Backplane Expander firmware fails with Windows DUP via IDRAC GUI and LCC(SCGCQ01313047)
 -Marlin B0: 0x4310 fault on fwHostBoot post clean flash on FW: 03.250.01.00(SCGCQ01318643 )
 -MR7.1: PD missing after system reboot during COL test . PD missing reported at POST(SCGCQ01318859 )
 -Reject profile change during Background Op in progress or cancel pending profile change to start Background Op (SCGCQ01320854)
  -(SCGCQ01324136)
 - JBOD drop during cable pull test.(SCGCQ01326924)
 -MR_7.3_FW : MonTask: line 332 in file ../../raid/taskman.c rst=0 while trying to delete 128 R0 DGs(SCGCQ01334150)
 -Check in files needed for CQ NVDATA Migration into FW source tree(SCGCQ01335640)
 -FW returning MFI_STAT_OK_REBOOT_REQUIRED for profile revert back(SCGCQ01337346)
 -MR7.3 (SCGCQ01337564)
 -Set gActiveFeatureSet.maxVds to correct value for any Profile(SCGCQ01337674 )
 -Controller hits montask and hangs on next boot when an Insight blade is inserted in the chassis.-(SCGCQ01337676)
 -(SCGCQ01341838)
 -MR 7.3 PA4: Controller restart command hung during IO on VD's and Jbod's (SCGCQ01343745)
- Static code analysis defect fixes in MR_FW_SAS3.5_7.3_FC(SCGCQ01345683)
-- Drives reported as missing after pinned cache flush is interrupted at SOD(SCGCQ01345827)
- Clean up DRAID Code (SCGCQ01348405)
 -Montask seen on line 151 in file ../../raid/span.c rst=0 , foreign import and cable push/pull .((SCGCQ01351581)
 -Montask : line 166 in file ../../raid/taskman.c rst=0 , while performing IOs on 240 R1 VDs with rebuild((SCGCQ01353560)
 -For single image COL, in least latency mode, FW offloads data without erasing flash.((SCGCQ01356545)
 -Join Mirror functionality not workingSCGCQ01368560)
 -dereferencing uninitialized pointer(SCGCQ01373232)
 -MR 7.3 :Fatal firmware error: Line 939 in ../../cpu/arm/exceptions.c when mprint passes incorrect parameters.(SCGCQ01374742 )
 -FW breaks into megamon for monSes.c while running IO on VD(SCGCQ01385184)
 -Kill adapter during single path cable removal/insertion.(SCGCQ01385424)
 -Issue (SCGCQ01388733)
 -[PL]Ventura MR 7.3 ((SCGCQ01389530)
 -In NVMe only profile not able to see the profile in profile get list.(SCGCQ01393547)
 -MR7.3: 4k PD Configuration can't be imported from iMR to MR Controller. However, it can be imported from MR to iMR(SCGCQ01395842)
 -Offload descriptors are 64 bit in size, resulting in offload errors.(SCGCQ01397850)
 -Virtual Address overlap results in skipping DDR ECC error checks when cache is dirty(SCGCQ01400126)
 -Storelib is not getting any data for NVMe encap command from the firmware(SCGCQ01402872)
 -Raid Map and Pd sync are updated for every OCR(SCGCQ01415120)
 -FW is continuously printing DmDevRecValidateRetry during Discovery with bad (0 MB) PD.(SCGCQ01418720)
 -Revert SCGCQ01418180 for 3616 and 3508 XSD, 3408 and 3416 remains the same.(SCGCQ01424266)
 -MR7.3.1 : user can set unsupported controller profile (ID: 12) on a OEM 16i controller(SCGCQ01509952)
 - Open Timeout Error Handling is too drastic(SCGCQ00089824)
 -SPV: Virtual Expander does not reply to SMP Report Zone Manager Password Request.(SCGCQ00135037 )
 -Fault x265D running random expander reset test in emulated external storage configuration(SCGCQ00135537)
 -Receipt of HARD_RESET data pattern causes firmware to perform error recovery in Target mode only(SCGCQ00135796 )
 -SPV: Add check to verify if a Virtual Function is allowed to access a Virtual Port.(SCGCQ00136685)
 -SASWideMaxQueueDepth not being set for direct attached wide port SSP target devices(SCGCQ00136975 )
 -Thunderbolt: PhySlowInit workaround should not be turned on(SCGCQ00138029)
 -Underlength Read on Falcon(SCGCQ00138247 )
 -Read Long command to SATA device does not complete(SCGCQ00143655)
 -FPGA : FPE FW (SCGCQ00143659 )
 -FPGA: Bugs in TBM code(SCGCQ00143878)
 -Fix Sata Init(SCGCQ00144557)
 -Obtaining proper value of Standby condition timer from Power condition mode page (page 0x1a) for a mode select command.(SCGCQ00144748)
 -0x6009 Fault During TARGET RESET TM Completion(SCGCQ00145193)
 -Gen3 TaskMgmt: TMs that send an SSP TASK IU always timeout and complete unsuccessfully(SCGCQ00145553)
 -Typo in SATA init code could result in wrong block size reported for non(SCGCQ00146128)
 -Fault 5804 on Firmware startup(SCGCQ00146974
 -Postponing and Disabled IO Path Bits Not Being Updated Through CudaMgr(SCGCQ00147136 )
 -Invalid Count Mismatch Error Handling for Fast Path IOs(SCGCQ00149150)
 -Fw hang (and fault) during IO increment with FPE disabled.(SCGCQ00149621)
 -(SATA Only): fault 0x7C33 while running fast path IOs to expander attached SATA drive(SCGCQ00151194)
 -SATA: infinite loop on sending IO while format is running(SCGCQ00151613 )
 -F/W hangs when sending IO while requester is disbaled(SCGCQ00155750)
 -0x6001 Fault while running TM Target resets durin Fast Path IO testing(SCGCQ00156005)
 -FPGA: Clearing Sata DMA Passthru Interrupt not occurring.(SCGCQ00157384)
 -Internal Task Management requests may be improperly constructed(SCGCQ00159014)
 -FPE: FP_DISABLED exception handling needs to check for a valid devhandle using the same checks as pliStartScsIO(SCGCQ00160011)
 -FPGA: SAS device page 0 fast path bit(s) not properly set(SCGCQ00160469)
 -Fast Path will be enabled for ATAPI tape device after a reset and init in CM (SCGCQ00165930 )
 -FPGA: Target Mode error injection testing results in a 0x265D fault.(SCGCQ00166409)
 -Fault 0xD071 seen when sending down Abort Task Task Management(s)(SCGCQ00169004)
 -Fault 0x4A00(SCGCQ00175661)
 -Fault 0x4d05 seen to ATAPI SEP device when internal request sense is issued.(SCGCQ00177620 )
 -TxCtxMgr interrupt handling uses incorrect register to determine which context is in error(SCGCQ00179621)
 -TM: Fault 0xD0ED while running task management(SCGCQ00179989 )
 -TM: 670A Fault in task management(SCGCQ00180216)
 -invalid parameter checks in TBM interface(SCGCQ00181781)
 -Fault 0x5826 when running Task Management tests(SCGCQ00183297 )
 -Fix 2 unguarded loops in Control Queue Cleanup(SCGCQ00183881)
 -Controller faults with code 6004(SCGCQ00187146)
 -Ensure that PL stops FPE on any PL sourced fault(SCGCQ00187765 )
 -Linking error with PL library(SCGCQ00192806 )
 -When an extra Data frame, or data is sent by SAS device for a READ, the device isn't sent a Task Management.(SCGCQ00192944)
 -FPE: Sata Init code causes recursive call to FPE Exception queue handling(SCGCQ00198255 )
 -Timeout of an Inquiry command to SATA drive which was already completed as failure(SCGCQ00199797)
 -Gen3: PM (SCGCQ00203543 )
 -Large Block IOs to SATA drives timeout (SCGCQ00206603)
 -Gen3: PwrMgmt (SCGCQ00207737)
 -PL layer notifies IOP layer for 0 timed out IO on receiving timeout interrupt.(SCGCQ00208538)
 -DMA Engine debug timers initial values cause immediate interrupt and fault(SCGCQ00208650)
 -Discovery does not complete with Bobcat expander.(SCGCQ00209645)
 -Fault 0x4852 while running target Modes IOs and disabling phys.(SCGCQ00210183)
 -Gen3 PwrMgmt: PwrMgmt memory request accesses IOP function (SCGCQ00210496)
 -Invader A0: Fault 0xD140 while doing random TMs to FAst Enabled SAS drives running IOs(SCGCQ00215178 )
 -Gen3: Power Management change request fails when direct(SCGCQ00216828)
 -Invader A0: Fault 0x6003 while power glitching random enclosures during Block Move Test(SCGCQ00219144)
 -fault D024 with timeouts while running straight IOs(SCGCQ00220650)
 -Fault 0x5833(SCGCQ00225772
 -SMP function failed during enclosure pull/push tests.(SCGCQ00227580)
 -Fault 0x7C20 occurs with cable glitches on a large topology(SCGCQ00230957)
 -Debug dump via "pl reg all" UART only dumped 1/2 of the DMA Transmission Q(SCGCQ00233599)
 -Invader A0: 0x5861 fault during stress and whole port cable glitches(SCGCQ00233716)
 -The BT999 Detection Algorithm was removed when WA for fault 4A00 was checked in(SCGCQ00242147)
 -Invader A0: 0xD071 fault during stress and whole port cable glitches(SCGCQ00250013)
 -Add DCR reg info on SASConfig Reg Fault 7C54(SCGCQ002510480)
 -Ensure parity correctly disabled if BT999 seen(SCGCQ00259200)
 -Invader B0: Zero IoCount event in active state should only be turned on for SATA(SCGCQ00283220)
 -PL: Firmware may not send Notify(Power Loss Expected) in accordance with the SAS Spec (SCGCQ00290667 )
 -IO hang while running IOs and enclosure cable pull push(SCGCQ00293701)
 -WriteBuffer in 'Write Data' mode executes with good status when Bufferid=0 and Buffer Offset=non(SCGCQ00297369)
 -Invader B0: Fault 0x61A0 while running Block Move Test to Direct Attached Drives(SCGCQ00319503)
 -Some IO accelerator registers are not yet available on FPGA(SCGCQ00349862)
 -Fixed pl_src build(SCGCQ00355601)
 -Back end PCI interrupts are not enabled(SCGCQ00357192)
 -NVMe: FW SGL translation doesn't work properly with buffers larger than 1 host memory page(SCGCQ00377286)
 -IOA hardware generates an incorrect AHCI command header(SCGCQ00383642)
 -AHCI Asynchronous Notification was not working (SCGCQ00393902)
 -[Dauntless] SkipCount and Host Chain Support not present for IEEE64 to NVME PRP translation(SCGCQ00395615)
 -Need Proper Routine for Initializing Cuda Timer Wheel RAM (Reset Sequence)(SCGCQ00403591)
 -7C32 fault(SCGCQ00404224
 -Need to handle DATALEN_GT_SGLLEN exception differently(SCGCQ00415490)
 -Unexpected D033 fault(SCGCQ00418247)
 -NVMe: Fix a few bugs from the SGL breakup code review(SCGCQ00418946)
 -Added support for non(SCGCQ00420921)
 -D115 fault after dumping 'pl pci regs all'(SCGCQ00424915)
 -AHCI: an address error will be reported with the wrong error status(SCGCQ00436941)
 -Max payload size of virtual bridges not configured during enumeration(SCGCQ00442730)
 -DDR not mapped for MegaRAID builds(SCGCQ00445331)
 -Incorrect Mid value used looking for unconfirmed response during HW cleanup(SCGCQ00449087)
 -Fault 0xd102 hit when IOP issued task management request(SCGCQ00456250)
 -Fault 0xd300 hit when a read/write IO to PCI device is unpended and resubmitted to firmware(SCGCQ00462188)
 -E80D fault running IO in a PCIe Switch config(SCGCQ00462334)
 -EC0F Fault when running IO + Abort Task TM to AHCI(SCGCQ00466209)
 -TM Fail ScsiIO Dev:MID Debug Print Displays Address Rather Than Opcode(SCGCQ00476208)
 -D300 fault during mixed auto/nonauto IO to multiple AHCI devices(SCGCQ00477054 )
 -Extra validation required for Silverhawk PIM1 settings(SCGCQ00484633)
 -SAS/SATA drives go missing while running block move IO and Random TMs(SCGCQ00493178)
 -SAS3.5: PL Status shows parent devH of second switch in cascaded switch setup is zero(SCGCQ00496013)
 -Backend PCIe completion timeout after a PCIe error message is received(SCGCQ00498112)
 -NVMe: IO timeouts with high queue depth PL translated read/write IOs(SCGCQ00498179)
 -SATL: WRITE SAME Handling with LBPRZ=1, UNMAP=1, ANCHOR=0 needs an additional check(SCGCQ00524994)
 -Data corruption runing heavy IO(SCGCQ00551309)
 -NVMe: LUN not validated before use in non read write translations(SCGCQ00562314)
 -Backend PCIe: possible command timeouts in low resource or queue full cases(SCGCQ00600854)
 -Firmaware fault 0x26B5 observed when sending IOUnit Control Message with OPERATION of SAS_PHY_LINK_RESET to PCIe switch dev handle(SCGCQ00601557)
 -Ventura: Fix plInit in which VENTURA_PORTING was eliminated causing ARM to crash(SCGCQ00615099)
 -D300 fault seen when SCSI Mode Select is sent to AHCI device(SCGCQ00630246)
 -Limit the number of phys during spin up configuration for the FPGA (SCGCQ00648198) 
 -Ventura: incorrect bits in interrupt mask(SCGCQ00668609 )
 -Ventura PL: Internal flag may be incorrectly disabled during Abort Task operations(SCGCQ00673302)
 -PL clearing interrupt is not getting reflected in Interrupt observe registers(SCGCQ00674340)
 -Ventura: arm_all compile error in SAS SERDES / Phy Files(SCGCQ00686674)
 -Intruder: Reset of SASCore 1 or 2 was not using correct value to clear reset bits(SCGCQ00698911 )
 -PL incorrectly faults when a non read/write IO to AHCI device hits FxCore exception when started through firmware path.(SCGCQ00700211)
 -PL:Restrict access to RxEEDPBuf in pl dbg(SCGCQ00709358 )
 -Data continues to be sent after RESPONSE for an IO is received before data transmission completed (SCGCQ00710281)
 -pl timestamp print fills ring buffer(SCGCQ00720114)
 -Remove redefinition of IOC_NUM_PHYS(SCGCQ00736730)
 -FW Controlled Spinup: Slot ordered spinup defects(SCGCQ00771112)
-NVMe: rename some structure definitions in the NVMe code(SCGCQ00771188)
 -Intruder FPGA: Data Underruns while doing Target Mode IOs(SCGCQ00776411)
 -Ventura: 430B fault with multiple devices attached(SCGCQ00779488)
 -Intruder FPGA: Fix Repeated Rising Edge Spinup Interrupt(SCGCQ007801970
 -pl: backend PCIe: read/write IOs with chain to native SGLs fail with IoFlags.FastPath set to 0(SCGCQ00813839 )
 -265D fault while running task managements(SCGCQ00817552)
 -Ventura: Fault 430A during intitialization(SCGCQ00825789)
 -Unmap FIS Port Translation Hangs if No Range List Entries are Generated(SCGCQ00844030)
 -Ventura: Fault 265D when pl dbg dumps PtrHwDmaQFreePointer(SCGCQ00852104)
 -Ventura: backend PCIe: D363 fault during PL init when PCIe device structures are placed in DDR(SCGCQ00853886)
 -Ventura: RxEEDP buffer init has wrong size(SCGCQ00855014 )
 -PL: IOs completed with good status when EEDP Check enabled and EEDP error injected with 4096 block size(SCGCQ00855669)
 -Ventrua FPGA: hit Fault 0x5801 running Data Integrity from RedEye(SCGCQ00857273 )
 -Ventura: NVMe: Some SCSI(SCGCQ00860696)
 -Intruder A0: MEDIUM ROTATION RATE is not updated in RIGID DISK GEOMETRY PAGE When MODE SENSE(10) is executed to SATA Drive(SCGCQ00864828)
 -Ventura FPGA: NumberOfSATATargets does not decrement(SCGCQ00866287 )
 -Intruder A0: IDLE and STANDBY CONDITION TIMER's are not updated properly in POWER CONDITION MODE PAGE for NON EPC Drive(SCGCQ00866637 )
 -PL: High latency on non(SCGCQ00867571)
 -PL: Remove unused variable in when sending SATA SCT data(SCGCQ00871675)
 -Ventura: Avoid PCIe device initialization while PCI discovery is active.(SCGCQ00871804 )
 -Host Driver Detects Target Mode Event Errors Regarding Subsystem(SCGCQ00874585)
 -Some PL_ASSERT Cases Could Fail To Detect Out of Range Errors(SCGCQ00896629 )
 -PL: Unnecessary conditional statement in firmware source(SCGCQ00907209)
 -Tiger: Remove usages in of SUCCESS (1) and FAILURE (0) defines(SCGCQ00913505)
 -IOP & PL: Move certain PL structures to use OCM PLB Segment 2(SCGCQ00917625 )
 -Ventura: backend PCIe: incorrect link rate may be reported in PCIe IO Unit Page 0(SCGCQ00925861)
 -PL: 265D fault when injecting errors into the data stream from a SATA drive(SCGCQ00928401)
 -Tiger: Fix it_fpga_dnt build error to pass build all.(SCGCQ00935031)
 -Tiger/PSB function parameters where not updated when Ventura/PDB functino was(SCGCQ00940318)
 -Ventura: Fault d053 running SATA IO (SCGCQ00944751)
 -PL: Fault 0x4300 when removing SATA devices from the topology(SCGCQ01000639)
 -Ventura A0: Fault 0x5828 while running Quarch Cable breaker Quarter phy glitch.(SCGCQ01000813)
 -Tiger: Workaround MPT Endpoint Captured BDF reg writing quirks(SCGCQ01007350)
 -Ventura A0: Fault 0x670A while running TM and SMP commands. (SCGCQ01008734)
 -Tiger FPGA: 0x6815 fault when we should see 0x5821(SCGCQ01012466)
 -Tiger Ventura (SCGCQ01018738)
 -PL: SMP Pass Through to SED attached expanders fail(SCGCQ01018755)
 -Ventura: backend PCIe: issues related to PCIe link configuration(SCGCQ01019734 )
 -PL: PCIe Device Page 0 does not clear Reserved fields(SCGCQ01021410)
 -Ventura: PL Fault 0000d073 (SCGCQ01039143 )
 -Ventura Tiger: Unsupported/Failed Task Managements should also be forwarded to Tiger before failing back to host(SCGCQ01041510)
 -Ventura A0: NVMe drive missing after few Lane/Phy glitches between PCIe switch downstream port and Endpoint(SCGCQ01046725 )
 -Tiger FPGA: Abort Task to SATA can cancel out Fast Path State Machine Expecting Zero IoCount status (SCGCQ01051203)
 -PL: SED attached devices not removed from IOC's device table(SCGCQ01068954)
 -Ventura: B0 requires check of enqueue register before disabling queue manager state machine(SCGCQ01070612)
 -Marlin A0: HBA goes to hung state while sending diag reset (SCGCQ01084604 )
 -Attached expander goes missing while performing controller phy hard resets and config page reads(SCGCQ01110176)
 -Ventura A0: Fault 0xC010 while unloading/loading the drivers in Target mode topology(SCGCQ01116345 )
 -Ventura/Marlin: backend PCIe: recursive fault may occur on PDB SysDma error(SCGCQ01116710)
 -Ventura/Marlin: Fault 0xECD0 seen if switch goes away before all NVME drives attached registered with host.(SCGCQ01126840)
 -PL: MidUsed not cleared when handling FPE Requestor Error(SCGCQ01134948)
 -FW fault 0x265d when unplugging active cable(SCGCQ01154156)
 -PL: Possible null pointer access in a non(SCGCQ01168086)
 -PL: Unchecked function return value in sata code(SCGCQ01169267 )
 -Ventura: PL fault 5811(SCGCQ01184674)
 -Virtual SES Target Not Reported to the Host(SCGCQ01197507 )
 -Ventura: backend PCIe: compatibility tweaks for NVMe devices(SCGCQ01201787 )
 -Ventura: backend PCIe: NVMe IOs may halt when a backend PCIe link recovery occurs(SCGCQ01206643)
- Fault 0xEC3D seen during switch initialization(SCGCQ01210423)
 -PL Fault 0xd077 is seen while drives are pulled with IOs outstanding(SCGCQ01222435 )
 -Fault seen when handling Task Managment with IOs to NVME drives when drive reports media errors.(SCGCQ01226478)
 V-entura/Marlin: backend PCIe: EC84 fault(SCGCQ01229418)
 -Ventura B0: backend PCIe: link gets stuck down after a link break(SCGCQ01231751)
 -Add option to enable support for OEM specific NVMe Enclosures testing(SCGCQ01250846)
 -NVDATA config option to disable PL Virtual SES support(SCGCQ01251655)
 -Ventura MR 7.1, RHEL 7.2: SAS/SATA HDD R0/10/5, OLTP, Q >= 16, Up to (SCGCQ01255912)
 -Checks for reconstruction in place.(SCGCQ01276354)
 -pl: NVMe: Task Set Full handling flag not respected for NVMe(SCGCQ01289543)
 -Ventura/Marlin: backend PCIe: EC0E fault may occur on link down(SCGCQ01292448)
 -Assertion failure in ../../dm/mpt2/mptframe.c at line 788: id!=MPT_FRAME_ALLOC while enclosure powercycle.(SCGCQ01311481)
 -CSET Aggregator: SCGCQ01297325, SCGCQ01289572(SCGCQ01318920)
 -Disable fw messages "cmdId:5e has different completion status for sub commands" when convert 240Pds to Jbod and reboot(SCGCQ01320953)
 -Controller montask after data abort exception handler was called(SCGCQ01324312 )
 -Fix Static Code analysis issues(SCGCQ01325320 )
 -Mode page access to same devId needs to be serialized(SCGCQ01329539)
 -7.3: Need to adjust ProfileMaxDevices for Profiles other than 240 VD Profile(SCGCQ01330851)
 -PA1: fw hit PL D10D while format partition(SCGCQ01333872)
 -8G offload changes ONFI offsets (SCGCQ01336017)
 -PCIe SSD Fails to blink Bad Phy after 5 minutes, on Passive BP with internal adapter(SCGCQ01339684)
 -Assertion failure in ../../dm/src/FindDev.c at line 261 while connecting 10 enclosures to the system(SCGCQ01342054)
 -Ventura MR 7.3 (SCGCQ01342174)
 -After send command to PD to clear LED, don't poll for completion(SCGCQ01342947 )
 -7.3 pk484 unxpctd c_ptr 19804640 tgtId ef while migrate from 2DR1 (SCGCQ01343118 )
 -DEV Defect to address Code Collab defects/comments for CQ# 1304715 & 1320083 (SCGCQ01343240)
 -mix mode: NVMe pd turn to foreign config after couple of OCR.(SCGCQ01344064)
 -7.3: FW hit KA when insert SAS for multipath with 48JBODs in controller(SCGCQ01347504)
 -FW changes to make NVRAM baselines between 7.3 and 7.1 in sync(SCGCQ01348744)
 -Dev Defect: Don't refer LMID before dism start in the case of device hot plug(SCGCQ01350309 )
 -MR7.3 NVME drives in Fast Path iops drop to 0 while in megamon(SCGCQ01353696)
 -NVME profile B was not shown to user(SCGCQ01354313)
 -MR 7.3_FW_PA4: MonTask: line 332 in file ../../raid/taskman.c rst=0 during Patrol read with IO's on 240 VD with media errors.(SCGCQ01356270)
 -7.3 pk564 Crusader taskman when remove sas cable in multipath(SCGCQ01376326)
 -Restore nvram flag allowOnlineCtrlReset after set factory default completes(SCGCQ01378753)
 -lastDmaChannel is updated by both cores without a semlock(SCGCQ01378860 )
 -StorCLI show profile 13 with 8 NVMe drives support(SCGCQ01392900)
 -Data flush to drives after cache offload taking ~250 seconds.(SCGCQ01401796)
 -Update nvram.h with correct size for curAdpPersonality(SCGCQ01404432)
 -BusReadWriteSW() is not reading back the data that was written to make sure data is flushed through PCI buffers(SCGCQ01405191)
 -Reduce number of block(SCGCQ01408312)
 -OEM controller shows random slot number inside HII after hotplugging enclosure(SCGCQ01415422)
 -Disable OOB FW download.(SCGCQ01424907 )
 -OEM controller has incorrect drive enumeration with single IOM(SCGCQ01431119)
- Bugzila 112779 - [SAMSUNG PM863A SSD can not show the "Part Number"/ "FRU Number" information under XCC web w (SCGCQ01435624)
- 9460-8i card connect drive through direct-attached backplane: error LED not on when drop out a drive. (SCGCQ01445040)
 -Single Thread MSI-X and MCTP accesses(SCGCQ01446273)
 -Change CACHE_HEADER_VERSION from 13 to 11(SCGCQ01465054)
 -930-16i Cannot Spinup HDD During System Power On(SCGCQ01470741)
 -When update Toshiba SAS 2.5" 10K 12Gbps 300GB HHD (PN:SH20J34185) controller hangs(SCGCQ01515259)
 -ATA Trusted Receive DMA cmd may not DMA data to host buffer(SCGCQ00123945)
 -Status FIS filelds are zero SATA Passthrough reply for PIO(SCGCQ00141209)
 -When an IO is completed that had the Cuda MID State Table Reply Destination set to '1', the value must be cleared.(SCGCQ00147131)
 -Incorrect TM print for IOs owned by Fast Path Engine(SCGCQ00151628)
- SAS-3 FW FPE Checkpoints Interfere with Code to Decrement the IO Count(SCGCQ00151849)
 -bitfields in SMP Report EDFB Settings response not being processed correctly(SCGCQ00155514)
 -Task Management does not properly recover from out of resources condition(SCGCQ00158320)
 -The code got ported to gen3 incorrectly.(SCGCQ00161663)
 -IOcount would get incremented even though Timer addition failed(SCGCQ00168907)
 -Write IOs stall during task management(SCGCQ00169848)
 -plFpeiAddIOTimer needs to use a unique fault code in its call to PL_VALIDATE_MID. This is provide support for faster debug from customer site.(SCGCQ00170054)
 -When using Fast Path Timer, IO Count could get corrupted(SCGCQ00170066)
 -When Task Set Full revceived from device that has Fast Path IO occuring, IO timeout can occur.(SCGCQ00189418)
 -Fault 0x5844 while running Target Mode IOs(SCGCQ00189760)
 -SATA I/O gets stuck after passthrough command(SCGCQ00190187)
 -Fault 0x26B1(SCGCQ00201183)
 -iopiMemoryMove() called without setting End of List bit in (SGESCGCQ00210189)
 -Invader A0: Fault D025 while pausing completor during timer error(SCGCQ00220525 )
 -Fault 0x6708(SCGCQ00231532)
 -Fault 0x5861 is encountered during Block Move Stress and 5ms Whole Port Glitches(SCGCQ00251812 )
 -TM timeout during enclosure pull push(SCGCQ00257768)
 -When doing Task Managmeent cleanup, an invalid Parity error may be caused by HW cleanup(SCGCQ00280175)
 -Invader B0: (PL) Fast Path getting disabled incorrectly when a pre(SCGCQ00281921)
 -IO hang while running straight IOs on a mix of SAS and SATA drives(SCGCQ00290510)
 -Invader discards valid response data for some SMP from host.(SCGCQ00301259)
 -Fault 61a2 while running IOs on a mix of SAS and SATA(SCGCQ00319691)
 -Invader B0: Remove unused print strings in PL firmware(SCGCQ00326797)
 -Fixed Firmware Bug in Queue Manager(SCGCQ00337252)
 -pl: Need to re(SCGCQ00349888)
 -Fixed devhandle numbering for SAS/SATA devices(SCGCQ00353284)
 -Initial bring up in lab for AHCI(SCGCQ00356058)
 -Need UART commands to show backside PCIe information(SCGCQ00364512)
 -(IOA) Dauntless throws a FPE_CMPL_ERR_FPE_NOT_SET_IN_MID_TABLE error during internal TM's(SCGCQ00365805)
 -No functional change (SCGCQ00365923)
 -No functional change, temporary workaround(SCGCQ00383647)
 -Updated firmware to match latest PCIe hardware(SCGCQ00396444)
 -RAIDContextOfffset field in Message Config Registers are not correct(SCGCQ00397602)
 -1609 Fault with bad AHCI device(SCGCQ00400048)
 -NVMe: Miscompare during block move test with backend NVMe device(SCGCQ00413256
 -PCIe discovery fails with PL 250.04(SCGCQ00422097 )
 -PL: SGL print for debug may not work properly(SCGCQ00433625)
 -SATA Passthrough message to AHCI device gets DEVICE_NOT_THERE status(SCGCQ00447819 )
 -E00E fault occurs during heavy IO to AHCI devices(SCGCQ00449814)
 -PL: ownership of frame containing a non read write IO to a backend PCIe device(SCGCQ00456377)
 -PL:PCI: Chunk of memory is being assigned to Switches while switches don't need this memory(SCGCQ00472124)
 -0xD300 Fault is seen during Stang admin complete interrupt handling.(SCGCQ00473898)
 -PL: D074 fault(SCGCQ00485929)
 -Dauntless FPGA: 584B fault while running block move IO and Random TMs(SCGCQ00503522)
 -Backend PCIe completion timeout prevention bugfixes(SCGCQ00505131)
 -Read of PCIe Device Page 1 or 2 using the get(SCGCQ00518221)
 -NVMe: Fault EC0F during IO (SCGCQ00556768 )
 -(AHCI Only) No Data returned on sending ATA Passthrough with ata command set as 'READ DMA Ext' to an AHCI Device. (SCGCQ00598952 )
 -Replace leftover direct POM accesses in NVMe module with wrapper functions(SCGCQ00649571)
 -Intruder: Fault 6B00 when attaching SATA drive to SAS Core 1(SCGCQ00671376)
 -Fault 0x7C33 when running with SATA drives and TM occurs(SCGCQ00757494 )
 -6001 fault while running TMs in Linux(SCGCQ00771763)
 -pl: backend PCIe: init failure reason bitfield is too small(SCGCQ00776266)
 -Rising edge spinup interrupt needs to be cleared once spinup retry attempts have been exhausted.(SCGCQ00805176)
 -IOP directly accesses PL instead of using PLI(SCGCQ00820292)
 -Round 1 of fixes for issues found while performing basic dev test for PCIe error interrupt path(SCGCQ00843113)
 -PL: Controller reset observed during IO's running when customer specific enclosure is removed from SAS Topology(SCGCQ00859725)
 -PL: STANDBY_Z Bit Not Set in POWER CONDITION MODE PAGE When Mode Sense (10) is executed to NON EPC SATA Drive(SCGCQ00860528)
 -PL: SATA performance drop(SCGCQ00901563)
 -Ventura: backend PCIe: EC0F fault after read/write IO breakup in low resource case(SCGCQ00905252)
 -Tiger FPGA: 0x5854 when posting Trace Buffer during IO(SCGCQ00950016)
 -Ventura: 4F01 fault occurs if SAS and PCIe are both disabled for a phy(SCGCQ01010047)
- PL Fault 0x4852 is seen while breaking a lane of NVMe device attached behind a PCIe switch.(SCGCQ01048805)
- Ventura A0: Abort Task to Intel NVMe device results in IOC status 004a TM Failed(SCGCQ01063063)
 -Coverity defect: The assigned value that is never used.(SCGCQ01090001)
- Ventura: Persistent connection not established with hard drive that supports it. (SCGCQ01110300)
 -makedefs.h was copied to a non existing folder(SCGCQ01183745 )
 -Fault 0xECA0 seen while running IOs to NVMe drives(SCGCQ01263232)
- Ventura/Marlin: backend PCIe: link bandwidth poller keeps calling discovery on failure(SCGCQ01282006 )
 -MR 7.1_Double Dip COL causes loss of disk cache(SCGCQ01311127 )
 -Insertion of Faulty drive results in FW failure.(SCGCQ01321192)
- Assertion failure in ../../hw/inc/3516_inc/memory.h at line 342: isInAddressibleRange(virtualAddr)(SCGCQ01324245)
 -Assertion failure in ../../dm/src/devMgr.c at line 404: devId <= DM_MAX_DEVICE error(SCGCQ01328412 )
 -MonTask:...fusion.c rst=0 with Driver detected possible FW hang(SCGCQ01328760)
 -MR_7.3_FW: Not able to create more than 128 DGs in profile 12.(SCGCQ01332841)
 -Ventura: PL FW may Fault x61A5 during cable pull to an external enclosures with IOs outstanding(SCGCQ01334254)
 -Assertion failure in ../../hw/inc/3516_inc/memory.h at line 342: isInAddressibleRange(virtualAddr)(SCGCQ01334603)
 -MR7.3: while multiple rebuilding on 240LDs, FW prints constantly messages "C0:Rebuild delayforHeadOfQ..............."(SCGCQ01338964)
 -FW breaks at start of restore after a cache offload has occurred.(SCGCQ01343757 )
 -Don't show Profile 11 or allow to change to Profile 11 (NVMe only) if there are SATA/SAS drives present in the Controller(SCGCQ01345727)
 -Upgrade and downgrade across 8GB and 4GB FW crashes(SCGCQ01346593)
 -FW upgrade/downgrade across 7.x stream crashes with OCR/OFU(SCGCQ01351599)
 -Remove unwanted spaces and tabs!(SCGCQ01354410 )
 -MR 7.3 : DC during CopyBack on R6 VD(SCGCQ01372939)
 -MR 7.3 After migration completed then CC see inconistent parity on VD(SCGCQ01373200)
 -timestamp value in FW is incorrect(SCGCQ01376197)
 -AI to fix http://cmappsvr2:8181/ui#review:id=18558 to allow profile change(SCGCQ01379001)
 -MR7.3: Add improvement to profile compatibility determination code for profile show and profile change(SCGCQ01379148)
 -MR PARAMS page 0 does not get updated with the newer ROP that has NVDATA with a change in the same page.(SCGCQ01381617 )
 -MR 7.3 :PL Fault 0000d075 LR 01283991 , while running IO`s , CC and OCR in background.(SCGCQ01384714)
 -MR_7.3: Fw fault observed while R1 with max enclosure with single path power cycle(SCGCQ01388573)
 -Correct via file generation(SCGCQ01390690 )
 -Assertion failure in ../../dm/mpt2/mptTaskMgmt.c while R1 with max drives with cable pull/push [ 5mins delay] (SCGCQ01392076 )
 -Assertion failure in ../../onfi/Onfi2.c at line 6438: cacheSize % onfiHwConfig when do OFU from MR 7.2 GCA to MR 7.3(SCGCQ01392709)
 -JBOD IO's stopped on both MR/iMR Controller, after upgrading/downgrading from MR 7.3 PKG 657 to MR 7.1(SCGCQ01439507)
 -Purley Server: RHEL 7.3 kexec problem(SCGCQ01453576 )
 -MegaRAID with MCTP PCIe VDM not able to be rediscovered by BMC Emulator's MCTP service(SCGCQ01473240 )
 -Updating PL version to 0x03800000(SCGCQ01473873)
 -MR7.3.1 : iMR FW locks up and PSOD seen while trying to flash MR7.2.1 FW ROP(SCGCQ01516986)
 -Possible 0xD093 fault(SCGCQ00147128 
 -Fault 0xD093 when doing completions via Cuda to Firmware(SCGCQ00147274 
 -5110 fault when format unit command was sent to a WD NCQ SATA drive(SCGCQ00158622 )
 -FPGA: 0x2667 fault while printing SGL (SCGCQ00161803)
 -Fault 0x4851 while doing Abandon Class Open Reject testing(SCGCQ00168863)
 -Write verify to SATA does not complete.(SCGCQ00170317)
 -SMP and IOs timeout(SCGCQ00203069)
 -Invader A0: C009 fault while running Target Mode IOs and handling forced EEDP errors.(SCGCQ00204202)
 -PL does not handle completion from IOPCompletionQueue for PL Light IOs(SCGCQ00205349 )
 -PL Firmware attempts to execute out of invalid memory(SCGCQ00219453)
 -Drives lost when running IO and TM(SCGCQ00228742)
 -4A00 fault while injecting overrun error(SCGCQ00281682)
 -Data Corruption when running 1M IO with 32 outstanding IO count(SCGCQ00429490)
 -PCIe Io Unit Page 0 sets invalid AttachedDevHandle when no device attached(SCGCQ00440622 )
 -Abort Task TM duing IOs to AHCI device might cause FW to fault 0x4300(SCGCQ00442746)
 -Clear backend PCIe core DisableReadSideEffect flag(SCGCQ00450125)
 -AHCI: Spurious admin interrupt(SCGCQ00453515)
 -Fix issues encountered while unit testing non read write native SGL handling(SCGCQ00468465 )
 -Fault D300 while running queued IO to a non(SCGCQ00478557)
 -Completion timeout results in lock up(SCGCQ00484088)
 -EC07 Fault during loading of driver(SCGCQ00612644)
 -pl Diag Cmd 'Show Port' Displays additional Port.(SCGCQ00728635)
 -pl: Unbounded wait in plPhyClearErrorRegisters((SCGCQ00768573))
 -Consolidating a subset of CSETs from OEM stream to 7.1 stream(SCGCQ01286561)
 -SEP PD ID is not consistent(SCGCQ01310882)
 -Discount enclosure slots of internal SGPIO enclosure in calculating total number slots of total enclosures in determining whether or not to permit profile change from 11 to 10.(SCGCQ01324371)
 -MR 7.3 PA3 ::Assertion failure in ../../dm/mpt2/mptDirect.c at line 1388:during Enclosure power cycle with Foreign import.(SCGCQ01330382 )
 -(SCGCQ01335393)
 -MR7.3: After all 240PDs configured in Save mode, FW hit EXCEPTION while clear config(SCGCQ01351269)
 -NVMe drives become unconfigured bad after clearing configuration.(SCGCQ01374747)
 -Assertion failure in ../../dm/mpt2/mptTaskMgmt.c at line 746: , while Enclosure push pull(SCGCQ01375147)
 -While trying to import 240 VDs with 144 4k drives, getting hardware error (I2C) in storclif(SCGCQ01379156)
 -optimize fix made in flush path when there are no host ios during bootime(SCGCQ01390863)
 -Issue: ReleaseCandidate stamping still shows the This firmware is a TEST version... banner(SCGCQ01398387)
 -System will pop up “Cannot communicate with iButton to …” during reboot with Dania card (FW:50.2.1(SCGCQ01447988)
 -MR7.3.1_Assertion failure in ../../dma/dmaxor.c at line 1180:(SCGCQ01482384)
 -FPGA: Fault 6600 occurs when inject errors.(SCGCQ00157010)
 -Vendor specific PLI Control Requests not working(SCGCQ00160618)
 -Fault D074 during Destructive Domain Test(SCGCQ00168456)
 -FPGA: Firmware faults if a Response frame is received when in Target Mode.(SCGCQ00168476)
 -Fault 0x4A00(SCGCQ00194907)
 -Fault 0xD060 when sending TM and running heavy fast path IO(SCGCQ00196678)
 -TBM: Recursive faults when faulting in TBM(SCGCQ00241232)
 -Fault 0xD065 on SAS I/Os when timed out by Cuda(SCGCQ00465596)
 -PL:PCI: Debug data does not show information for Switches properly(SCGCQ00485164)
 -NVMe: fix function headers(SCGCQ00562246)
 -ventura: A0 silicon bring up (SCGCQ00941706)
 -Controller freeze and reset while Flushing dirty cache at bootup.(SCGCQ01318861)
 -In double dip case, cache offload is missed due to arming operations not being tied together(SCGCQ01335962)
- FW hit data abort (8d84) when heavy I/O for 15 mins(SCGCQ01339068)
 -rebuild restart from 0 when gracdful shudown or reboot.(SCGCQ01349083)
 -VMWare Passthrough: FW Hang when adapter configured for PCI Passthough and assigned to VM.(SCGCQ01371872)
 -Detect and Notify multiportconnection to same same SasAddress(SCGCQ01384565)
 -CPLD Flashing Error(SCGCQ01389519)
 -Exception Handler Return address 0x01362c7d when boot up(SCGCQ01404373)
 -FW does not respond to MCTP packets when BIOS is disabled (BMC emulator)(SCGCQ01473945)
 -address merge conflict from 73rc to 73lenovo(SCGCQ01499771)
 -FPGA: Target Mode testing with error injection can result in a 0x0501 fault.(SCGCQ00165997)
 -When extra data is sent for an IO started by Fast Path, appropriate error handling doesn't occur.(SCGCQ00197118)
 -Invader A0 : SATA Drive not getting detected.(SCGCQ0022172)
 -Command time out while issuing SATA passthrough requests.(SCGCQ00594631)
 -NVMe Drives Don't Discover on 8 GB Talladega Boards(SCGCQ01291028)
 -H840 montask while running AC cycle test during the 'cache offload testing'. Controller break into montask with Error Data Abort exeption.(SCGCQ01320912 )
 -7.3: NVMes Only pk 462 Fatal firmware error: Line 934 in ../../cpu/arm/exceptions.c when migrate 2DR1(SCGCQ01332424)
 -Raid level migration failing on MR(SCGCQ01337032)
 -Replacing latest NVDATA_CORE XSD to FW source code /fw/xsd.(SCGCQ01361515)
 -MR7.3: Hitting Data Abort exception after OCR during reconstruction.(SCGCQ01374875 )
 -MR 7.3 : on removing the PD's while running IO's on 240vd's and changing the VD policy in loop will result in montask.(SCGCQ01374969 )
 -MR 7.3.1 MixMode(SCGCQ01479653)
 -System will pop up “Cannot communicate with iButton to …” during reboot with OEM custom card(SCGCQ01501209)
 -Ventura BST 7.3(8GB)==>PD pull/insert _Handle DISM timer properly(SCGCQ01341844)
 -MR_7.3.1_Firmware hangs in discovery-(SCGCQ01484421)
  IR Path is not restored after expander connection is reestablished(SCGCQ00136967 port of SCGCQ00126969 )  
  - FW not returning error status on ATA aborted SCSI ATA Passthrough command(SCGCQ00136971 port of  SCGCQ00133038)  
  - Direct attached drive stalls when injected with bad xfer length in DMA setup FIS(SCGCQ00136972 port of SCGCQ00135839 )  
  - BT1680: Command timeout after drive error during workaround(SCGCQ00136974 port of  SCGCQ00136165)  
  - Add 64-bit multiplication, division, and modulus functions to PL(SCGCQ00138469 port of  SCGCQ00138467)  
  - Add 64-bit multiplication, division, and modulus functions to PL(SCGCQ00138470 port of SCGCQ00138467 )  
  - Add/Removal Events for Initiator cease after rebooting a switch(SCGCQ00142385 port of SCGCQ00142382 )  
  - PL: SATA Passthru command fails(SCGCQ00146018 port of SCGCQ00125322)  
  - Invalid Command Sequence following Link Reset(SCGCQ00146633 port of  SCGCQ00145634)  
  - Reset loop after induced TM during IO(SCGCQ00146634 port of  SCGCQ00145842)  
  - 6815 fault running IO and task management(SCGCQ00147872 port of  SCGCQ00147193)  
  - PL: SATA Passthru command fails(SCGCQ00149242 port of  SCGCQ00125322)  
  - Typo in SATA init code could result in wrong block size reported for non-512 SATA drives(SCGCQ00150247 port of SCGCQ00146128 )  
  - ReadCapacity returning 0xFFFFFFFFFFFFFFF on a SATA drive reporting a 0 LBA count(SCGCQ00150248 port of  SCGCQ00147027)  
  - 6815 fault running IO and task management(SCGCQ00150555 port of SCGCQ00147193 )  
  - SAS Device Page 1 data for first drive or single drive was all zero(SCGCQ00150560 port of SCGCQ00144104 )  
  - Possible to send a NCQ command during NCQ error handling(SCGCQ00153303 port of SCGCQ00151226 )  
  - 6001 format when inquiry is issued while format is active to a SATA device(SCGCQ00153305 port of  SCGCQ00151272)  
  - pl: SATL: Support write buffer mode 7.(SCGCQ00153476 port of  SCGCQ00148567)
  - ATAPI tape drive fails any command with Input/output error.(SCGCQ00154669 port of SCGCQ00147948 )  
  - Enable sending 3 identify frames(SCGCQ00155017 port of  SCGCQ00136668)  
  - PL: Add compile option to fault when Discovery detects Discovery Error 0x90 (SMP Timeout(SCGCQ00155434 port of  SCGCQ00149166)  
  - Change DMA engine default threshold values for System and DDR data(SCGCQ00155451 port of SCGCQ00146007 )  
  - Ph8: Host Based Discovery Request change(SCGCQ00155995 port of SCGCQ00147804 )  
  - Fix debug print param count mismatches and add compile-time assertion which detects mismatches(SCGCQ00159373 port of SCGCQ00156731)  
  - SATL: 620F fault with reassign blocks + invalid parameter list header(SCGCQ00160152 port of SCGCQ00153003 )  
  - PL: Msync needed to update VP_ID of SCSI IO request before posting the IO to SAS Core.(SCGCQ00160169 port of  SCGCQ00099988)  
  - (PL-Only  Mask out unused debug code on the IO path when not used(SCGCQ00160518 port of SCGCQ00156191 )  
  - PL: Port Enable and Config page requests timeout during large topology discovery.(SCGCQ00160710 port of SCGCQ00153048 )  
  - Don't fault if TM sent to an Expander(SCGCQ00162814 port of SCGCQ00125874 )  
  - PL: Remove Diagnostic Console prints during PL config page accesses(SCGCQ00162959 port of SCGCQ00155911 )  
  - BT1680: Read failure w/ loginfo 311a0005(SCGCQ00163420 port of SCGCQ00157003 )  
  - Link Reset is happening within one second after getting invalid initial FIS(SCGCQ00163527 port of SCGCQ00157920 )  
  - PL: Poor IO throughput on one drive in a two drive topology(SCGCQ00163602 port of SCGCQ00138378 )  
  - Fault x6815 with Mustang in I/T switching running Target Resets(SCGCQ00163606 port of  SCGCQ00156204)  
  - Fault 0x265D When SMP Discover can't be sent during TM processing(SCGCQ00163736 port of SCGCQ00163609 )  
  - Phase 8 IT: Fault 265D during driver load and device discovery in parallel(SCGCQ00164405 port of  SCGCQ00155966)  
  - PL: Add SAT translation of SCSI Unmap(SCGCQ00168430 port of  SCGCQ00143322)  
  - PL: Add SAT translation of SCSI WRITE SAME with Unmap/Anchor(SCGCQ00168595 port of SCGCQ00163761 )  
  - Port_Not_Required  port of  ) C(SET: IR/WH: Performance improvements for very large IO sizes port of  )  (SCGCQ00152205 (SCGCQ00169767 port of SCGCQ00152205) ) 
  - About Discovery Error(SMP Function Fail & SMP Timeout  of the SAS2008.(SCGCQ00170864 port of SCGCQ00150500 )  
  - "NOT RESPONDING" notification not sent for a device that is attached to a disabled Phy.(SCGCQ00172525 port of SCGCQ00163207 )  
  - Device ADD notification before the host unregistered the device.(SCGCQ00172529 port of  SCGCQ00161874)  
  - IR: Sense data incorrectly interpreted when the valid bit is set.(SCGCQ00172671 port of SCGCQ00170928 )  
  - PL: Debug: Log Descriptor format sense data(SCGCQ00172687 port of SCGCQ00169000 )  
  - BT1680: IOs failed with 31220000(SCGCQ00173290 port of SCGCQ00170382 )  
  - Hard reset does not abort all outstanding target I/Os(SCGCQ00173440 port of SCGCQ00171366 )  
  - pl: PwrMgmt: BT766 part 2 workaround no longer compiles(SCGCQ00173458 port of SCGCQ00171859 )  
  - Read Buffer command to a SATA device could fail unexpectedly(SCGCQ00173461 port of SCGCQ00172041 )  
  - (PL-Only  Fault 0x6001 When requesting Start Immediate commanad(SCGCQ00173462 port of SCGCQ00168440 )  
  - PL: Discovery error 0x82 during enclosure power cycle test.(SCGCQ00174740 port of  SCGCQ00168551)  
  - Potential for data corruption when sending a PIO read command to a 4K sector drive via a SATA passthrough message.(SCGCQ00177383 port of SCGCQ00175847 )  
  - SGPIO Activity LED may blink on a non-IO drive while running IO's to other drives(SCGCQ00178837 port of  SCGCQ00160881)  
  - Reading Dma buffers via snapshot or UART while IOs are in progress(SCGCQ00179463 port of SCGCQ00139946 )  
  - 620F fault on SAS read data overrun(SCGCQ00188488 port of SCGCQ00185996 )  
  - Good status being returned on TM to missing SATA drive(SCGCQ00188688 port of SCGCQ00159495 )  
  - Disabling one phy causes another phy to be reset.(SCGCQ00188692 port of SCGCQ00174380 )  
  - Add debug command to enable printing of set number of dwords of raw frame(SCGCQ00188772 port of SCGCQ00025412 )  
  - SATL: Need to update standard inquiry version descriptors(SCGCQ00188781 port of  SCGCQ00168345)  
  - Indicate SAS connector Phy lanes reversal in Sgpio virtual SMP req(SCGCQ00188870 port of SCGCQ00174969 )  
  - SATA: NCQ read command is not completed after a data underrun or overrun(SCGCQ00199307 port of SCGCQ00185998 )  
  - SATL: Fault 7C22 when translating WriteSame(16  SCSI command(SCGCQ00203750 port of  SCGCQ00199678)  
  - PIO-mode SATA passthrough command hangs(SCGCQ00218121 port of SCGCQ00201227 )  
  - SATA NCQ Write Command sent using SATA Pass Through is not acted in case of NCQ Tag greater than 0 after DMA setup of 6Gbps device.(SCGCQ00218122 port of SCGCQ00193116 )  
  - (PL&IOP  Modify code to improve thunderbolt performance(SCGCQ00218354 port of  SCGCQ00203441)  
  - Entire topology goes missing while injecting errors into DMA Setup FIS(SCGCQ00218404 port of SCGCQ00203694 )  
  - pl: SATA: Queued translated commands to a single SATA drive can cause command failure(SCGCQ00224768 port of SCGCQ00188098 )  
  - SMPs are issued by FW in target only mode during discovery.(SCGCQ00226333 port of SCGCQ00188716 )  
  - IOs become pending for 2 minutes due to faulty SSD drive in topology(SCGCQ00232099 port of  SCGCQ00225408)  
  - pl: SATL: Security Protocol In/Out may leak frames on command failure(SCGCQ00237490 port of SCGCQ00222965 )  
  - Read Long command fails with check condition for a 4K SATA drive.(SCGCQ00237686 port of SCGCQ00215151 )  
  - 0x265D Fault due to using invalid IO information on certain SATA errors.(SCGCQ00239707 port of SCGCQ00208181 )  
  - 5861 fault after link related parity errors(SCGCQ00240778 port of SCGCQ00183364 )  
  - SMP MaxTimeReducedFunctionality = 0 fails to come out of Reduce Functionality(SCGCQ00244103 port of SCGCQ00202349 )  
  - PL: Discovery may not complete for some ports(SCGCQ00244107 port of SCGCQ00208463 )  
  - PL: Event Replay may not occur in certain out of resource situations(SCGCQ00247183 port of  SCGCQ00219985)  
  - PL: Some events may not be sent when the controller is low on resources.(SCGCQ00247466 port of SCGCQ00202904 )  
  - Zero-length read/write commands to SATA drives cause unexpected SCSI_TASK_TERMINATED responses(SCGCQ00250549 port of SCGCQ00204657 )  
  - 5900 fault on ATA Passthrough (Hard Reset(SCGCQ00250550 port of SCGCQ00218730 )  
  - Add NVDATA bit to disable Notify(Enable Spinup(SCGCQ00250752 port of SCGCQ00208630 )  
  - Return Port info in the Device Status Change Event(SCGCQ00250754 port of SCGCQ00208203 )  
  - [internal only] PL: Output to the ring buffer if a Broadcast Reserved 4 is encountered(SCGCQ00252975 port of SCGCQ00189759 )  
  - (BUILD-Only  Create a GHS SDA PL build(SCGCQ00253252 port of  SCGCQ00193624)
  - Disable the internal HW interrupt to the FW for receiving the BROADCAST(Change(SCGCQ00254237 port of SCGCQ00204210 )  
  - PL calls iopiFrameOwned(  with a MID of zero(SCGCQ00254458 port of SCGCQ00205430 )  
  - pl: SATL: Security Protocol In/Out SAT-specific translations may fail(SCGCQ00254697 port of SCGCQ00218425 )  
  - pl: SATL: Add handling of security locked state(SCGCQ00257362 port of SCGCQ00223621 )  
  - Assign all targets and SSP initiators to a non-zero DMA Group(SCGCQ00259862 port of SCGCQ00235650 )  
  - SATA: Partial link power management mode is disabled after dWord sync is lost(SCGCQ00264374 port of SCGCQ00224893 )  
  - Quick remove and attach of SAS Cables Drops Expanders from Topology(SCGCQ00278338 port of SCGCQ00208584 )  
  - Invalid topology change event sent by controller firmware when a device is removed(SCGCQ00279916 port of SCGCQ00231362 )  
  - pl: SATL: Command timeouts with multiple simultaneous non read/write commands(SCGCQ00280552 port of SCGCQ00229723 )  
  - IR was failing drives and marking the volume degraded or broken when under device missing delay(SCGCQ00280559 port of SCGCQ00235638 )  
  - PL: Devices not reported as not responding after an SMP Open Failure in some cases.(SCGCQ00280813 port of SCGCQ00242753 )  
  - Change the behavior of the LBPWS bit on the logical block provisioning VPD page for SATA drives(SCGCQ00281541 port of SCGCQ00231172 )  
  - (Sata Only  Executing Start Stop Unit to move SATA Drive from Standby to Active doesn’t work(SCGCQ00297098 port of SCGCQ00280727 )  
  - Controller may fault on bad response with incomplete write data transfer(SCGCQ00297426 port of SCGCQ00237417 )  
  - SATL: Bad status value for ATA Passthrough (12/16  commands with multiple FIS PIO transfer(SCGCQ00313937 port of  SCGCQ00271456)  
  - Extra 60 Bytes of VPD Page Data is Provided When SCSI Inquiry to VPD Page 0x89 is Executed(SCGCQ00314374 port of SCGCQ00285864 )  
  - PI error reported when PI error detected due to a frame CRC error(SCGCQ00314686 port of SCGCQ00262937 )  
  - (GEMINI  Incorrect data length reported for failed target mode transfers(SCGCQ00315207 port of SCGCQ00281690 )  
  - PL: SAS Device Page 0 may not return correct values(SCGCQ00315211 port of SCGCQ00265379 )  
  - SAS write command may complete successfully if target sends premature response frame(SCGCQ00315638 port of SCGCQ00264854 )  
  - (Sata Only  SCSI command 0x9E with service action 0x00 is not failed by SATL.(SCGCQ00317010 port of SCGCQ00282613 )  
  - SAS2 IT - Phase 14 – Request Sense SCSI Command data is incorrect for a SATA Drive During Stanby Power Condition Mode(SCGCQ00317952 port of SCGCQ00283312 )  
  - Read Long command to SATA device does not complete(SCGCQ00319992 port of SCGCQ00143655 )  
  - 7E12 fault with BT1680 and defective SATA drive(SCGCQ00320007 port of SCGCQ00188344 )  
  - SATL: improved handling of CHECK POWER MODE response(SCGCQ00320029 port of SCGCQ00231519 )  
  - Fault 4300 observed during reset all Expander phys with IOs(SCGCQ00320034 port of SCGCQ00238905 )  
  - ATA Error to SCSI Sense Translation Cleanup(SCGCQ00320036 port of SCGCQ00245732 )  
  - PL: Discovery print too long(SCGCQ00320039 port of  SCGCQ00251472)  
  - (Sata Only  Mode Select (10  to POWER CONDITION Page is Failed When IDLE CONDITION TIMER is Set to Non-Zero Value(SCGCQ00320050 port of SCGCQ00280725 )  
  - SAS2 IT - Phase 14 – Allocation Length for SCSI READ MEDIA SERIAL NUMBER Command is not Handled Properly(SCGCQ00320053 port of SCGCQ00283688 )  
  - pl: SATL: Sense data Valid bit and Information field may not be populated correctly(SCGCQ00320056 port of SCGCQ00284265 )  
  - pl: SATL: Translation for foreground SELF TEST CODE field in Self Test Results log is incorrect(SCGCQ00320060 port of  SCGCQ00286118)  
  - SAS2 IT-Phase 14-SATL-'Additional Sense' incorrect for REQUEST SENSE wrt. state transition sequence Standby->Active->Stop(SCGCQ00320064 port of SCGCQ00299765 )  
  - SATL translation happens in firmware for a Persistent Reservation Command with SA=3 for a Invalid PLL(SCGCQ00320750 port of SCGCQ00286094 )  
  - 0x265D Fault occurs when Inquiry to page code 0xB1 issued while a drive is under format or self-test.(SCGCQ00320752 port of SCGCQ00283697 )  
  - (Sata Only  READ MEDIA SERIAL NUMBER SCSI Command Return’s data for Incorrect SERVICE ACTION field(SCGCQ00321368 port of SCGCQ00283320 )  
  - SAS2 IT - Phase 14 – Allocation Length for SCSI INQUIRY Command is not Handled Properly(SCGCQ00321662 port of SCGCQ00280880 )  
  - PL: Allow ReportDeviceMissingDelay to be set to 1 sec(SCGCQ00323830 port of  SCGCQ00249951)  
  - ATA Trusted Receive DMA cmd may not DMA data to host buffer(SCGCQ00335403 port of SCGCQ00123945 )  
  - SATA commands take too long when unit attention set or SATA init is needed(SCGCQ00335410 port of SCGCQ00163455 )  
  - SAS 1.1 drive connected to 2008(SCGCQ00335437 port of SCGCQ00260362 )  
  - SAS2 IT: PL Fault 0x4203 seen when trimming LBA's out of Range(SCGCQ00335451 port of SCGCQ00328153 )  
  - PL: Configurable AWT for Expanders(SCGCQ00335507 port of SCGCQ00241199 )  
  - PL: SATA IO aborts with log info code 0x31120D02(SCGCQ00406361 port of  SCGCQ00320469)  
  - Read buffer command with non zero buffer offset doesnt behave as expected.(SCGCQ00411503 port of SCGCQ00328086 )  
  - SAS2 IT - Phase 15 – No Data Returned for VPD Page 0xB0, 0xB1 and 0xB2 During SATA Drive Format(SCGCQ00412533 port of SCGCQ00337310 )  
  - Invader B0: PL FPE - In Fpe Init remove memsets to 0 to reduce boot time.(SCGCQ00414350 port of SCGCQ00310854 )  
  - SAS2 IT - Phase 15 – Allocation Length for INQUIRY SCSI Command is not Handled Properly during SATA Drive Format(SCGCQ00416127 port of SCGCQ00334559 )  
  - pl: SATL: Report Luns command sent to SATA drive fails if the drive is spun down(SCGCQ00426177 port of SCGCQ00333109 )  
  - An expander goes missing during cable pull testing and doesn't come back on subsequent discovery attempts(SCGCQ00427246 port of SCGCQ00255659 )  
  - Set phy polarity base on nvdata(SCGCQ00434193 port of SCGCQ00345786 )  
  - Wrong Index value being passed to plInterruptTrackerRecord( .(SCGCQ00434943 port of SCGCQ00350600 )  
  - EDFB: report actual drive link rate in SAS Expander Page 1(SCGCQ00435531 port of SCGCQ00182604 )  
  - Faulty drive causes timeouts on other devices(SCGCQ00436186 port of SCGCQ00231960 )  
  - PL: Configurable SMP retries(SCGCQ00437960 port of SCGCQ00271092 )  
  - Invader C0: SATA PM – Fault 0x6B02 on SATA_PMNAK response to PM Control Request.(SCGCQ00439686 port of SCGCQ00391006 )  
  - PL Library customer not seeing links come up starting in .107 build(SCGCQ00439740 port of SCGCQ00379260 )  
  - Invader: IO timeouts while running IOs on Intel SSDs(SCGCQ00445285 port of SCGCQ00361587 )  
  - The wrong amount of data is transferred when INQ to VPD page 0x89 is received while a device is doing self-test or a format.(SCGCQ00445309 port of SCGCQ00337293 )  
  - (Sata Only  SATL fails UNMAP command with zero Parameter List Length(SCGCQ00445310 port of SCGCQ00329909 )  
  - Invader: Enable SAS Core Parity Interrupts(SCGCQ00449638 port of SCGCQ00361839 )  
  - Remove power management control flags from Manufacturing Page 3(SCGCQ00450890 port of SCGCQ00293362 )  
  - Invader C0: Firmware should fault if a parity error is deteced while reading asynchronous event from fast path hardware.(SCGCQ00451375 port of SCGCQ00377564 )  
  - Invader: Fixed Link Layer Parity Checking Prints(SCGCQ00459049 port of SCGCQ00356530 )  
  - Invader B0: Firmware not using correct start address while handling data overrun interrupt(SCGCQ00462166 port of SCGCQ00351468 )  
  - INQUIRY SCSI Command is not Failed for Unsupported VPD Page during SATA Drive Format(SCGCQ00462496 port of SCGCQ00334577 )  
  - Data TLB Error exception while running the BST.(SCGCQ00463051 port of SCGCQ00377481 )  
  - Invader: Fixed Issue Found in Data Overrun Testing Where IOs Were Being Incorrectly Completed(SCGCQ00463429 port of SCGCQ00363670 )  
  - (Sata Only  UNMAP command with "Number of Logical Blocks" set to 0 fails with command Abort(SCGCQ00464332 port of SCGCQ00328206 )  
  - Medium type field populated incorrectly in device mode page header.(SCGCQ00464390 port of SCGCQ00329954 )  
  - pl: SATL: Commands may fail after Write Same command failure(SCGCQ00466477 port of SCGCQ00328222 )  
  - Serdes settings to fix 12G SSC profile(SCGCQ00468679 port of SCGCQ00343925 )  
  - PHY InvTxData/InvRxData polarity may not change with Ext Manufacturing Page 40 settings(SCGCQ00469138 port of SCGCQ00393297 )  
  - Invader C0: replace msync with FLUSH_WRITE during manual IO count increment(SCGCQ00469143 port of SCGCQ00383667 )  
  - PARAMETER CODE, FORMAT AND LINKING and PARAMETER LENGTH are Not Populated in Self-Test Results Log Page(SCGCQ00469847 port of SCGCQ00339497 )  
  - SAS2 IT - Phase 15 – When SATA Drive is Moved to Active Power Condition from Idle Using START Bit, ASC/ASCQ is Incorrect(SCGCQ00470270 port of SCGCQ00336534 )  
  - Fix merge error(SCGCQ00470571 port of SCGCQ00393421 )  
  - SAS2 IT - Phase 15 – REQUEST SENSE's ASCQ is Incorrect When SATA Drive State Transition Happens (ie  Active->Stopped->Idle(SCGCQ00472074 port of SCGCQ00334642 )  
  - Cobra / Fury performance with Lightening 6G SAS SSD drives(SCGCQ00472476 port of SCGCQ00377946 )  
  - (GEMINI  Perf Enhancement - Move RL data to CRAM (also create mreq m command(SCGCQ00472914 port of SCGCQ00146873 )  
  - Program the pre-loaded preset used to lock-in the bitstream at the start of Tx Training(SCGCQ00473943 port of SCGCQ00354681 )  
  - Transmitter Training Part 1(SCGCQ00474680 port of SCGCQ00357497 )  
  - Add C0 SAS Phy SerDes initialization checks.(SCGCQ00476791 port of SCGCQ00378432 )  
  - Transmitter Training Part 2(SCGCQ00480619 port of SCGCQ00364214 )  
  - PL: Transmitter training part 3(SCGCQ00480624 port of SCGCQ00370018 )  
  - Invader C0: Performance drops with PL version 0.250.113.0 on 2 R0 volumes behind Cobra(SCGCQ00494101 port of SCGCQ00400569 )  
  - SMP Passthrough request may fail(SCGCQ00495883 port of SCGCQ00378926 )  
  - Fixed Bug in SATA Link Reset Code Which Could Stall the Task Management Request(SCGCQ00498486 port of SCGCQ00399690 )  
  - PL: Check iopiMemoryMove(  Return Status - SATL Inquiry Command Translation(SCGCQ00498849 port of SCGCQ00419472 )  
  - PL: SAT3 Compliance - Implement Translation of Set Timestamp Command (Disabled(SCGCQ00503815 port of SCGCQ00357128 )  
  - RxFM power management control workaround(SCGCQ00523847 port of SCGCQ00523419 )  
  - PL: SAT3 Compliance - Implement Translation of Report Timestamp Command (Disabled(SCGCQ00528525 port of SCGCQ00357126 )  
  - PL: Possible performance drop in small topologies.(SCGCQ00529283 port of SCGCQ00386639 )  
  - Invader C0: Fixed Problem with Lost Mismatch Connection Causing Channel Lockup on Link(SCGCQ00529286 port of SCGCQ00390972 )  
  - Update serdes settings due to B0->C0 hardware change(SCGCQ00530334 port of  SCGCQ00391401)  
  - Invader C.0: Power Management port width modulation phy states is wrong when Communicate Intent feature is turned off.(SCGCQ00530403 port of SCGCQ00392186 )  
  - Invader C0: Minor Fix to Task Management Interface Function(SCGCQ00531090 port of SCGCQ00395280 )  
  - Invader C0: Fix Comment in plTaskMgmtCleanup((SCGCQ00531098 port of SCGCQ00395191 )  
  - PL: Check the parameter range when handling pli temperature request(SCGCQ00549033 port of SCGCQ00415150 )  
  - PL: Zero out some internal structures(SCGCQ00549876 port of SCGCQ00245480 )  
  - Flag RxEEDP general control PortRecieveMode field with DONOTUSE as per [SAS3Core]1086(SCGCQ00551612 port of SCGCQ00413969 )  
  - Invader incorrectly programs route entries on expanders(SCGCQ00553032 port of  SCGCQ00243512)  
  - Fixed Cases of IocNum Parameter Hard Coded to 0 in Calls to iopiMemoryMove((SCGCQ00553035 port of SCGCQ00377294 )  
  - Cable Management: Link rate doesn't go upward when higher speed rated cables are used(SCGCQ00553038 port of SCGCQ00392871 )  
  - PL: SAT3 compliance - Support additional modes for Write Buffer command translation (Disabled(SCGCQ00553455 port of SCGCQ00357130 )  
  - PL: SAT3 compliance - Support for ATA EPC in SCSI Start Stop Unit command translation.(SCGCQ00553489 port of SCGCQ00357136 )  
  - PL: SAT3 Compliance – Implement Power Condition Mode Page translation with ATA EPC.(SCGCQ00553528 port of SCGCQ00406792 )  
  - PL: Host Based Discovery HBD Phy Event contains incorrect PhysicalPort field(SCGCQ00554333 port of SCGCQ00442735 )  
  - PL Host Based Discovery updates for Gen 3(SCGCQ00556327 port of SCGCQ00395436 )  
  - PL: Move temperature sensor init code down to PL(SCGCQ00556330 port of SCGCQ00410822 )  
  - Fixed Incorrect Fault Code When Link Up/Down Data Parity Error Workaround is Disabled(SCGCQ00557359 port of SCGCQ00414630 )  
  - Fixed Unnecessary Fault Occuring in Switching I/O with Task Management Test(SCGCQ00557361 port of SCGCQ00415922 )  
  - (PL  0x5805 Fault during IO + Task Management test(SCGCQ00562814 port of SCGCQ00433677 )  
  - SMP Discovery Error 90 after issuing Reset Task Management on Initiator(SCGCQ00563450 port of SCGCQ00437449 )  
  - Added Cleanup Code in Tx Context Manager for SSP Payload Only DMA Entry Type(SCGCQ00563453 port of SCGCQ00437532 )  
  - IO on a SATA SSD configured as JBOD pending with PL does not complete(SCGCQ00566089 port of SCGCQ00407250 )  
  - Fixed SATL Translation of Mode Sense Command(SCGCQ00566097 port of SCGCQ00425017 )  
  - IOP: Memory Coherency not enabled in Detroit(SCGCQ00566099 port of SCGCQ00432917 )  
  - Host Based Discovery: IOs sent to the controller may never be responded to(SCGCQ00566116 port of SCGCQ00450812 )  
  - Invader: The CLI commands need to have their text consistent.(SCGCQ00566120 port of SCGCQ00457380 )  
  - iop pci commands need to be updated to use dword instead of word to be consistent(SCGCQ00566123 port of SCGCQ00457386 )  
  - cli command - pl sfr (Display Starfish register  faults firmware 0x265D(SCGCQ00566127 port of SCGCQ00457395 )  
  - Invader: pl fpe mgrdstt cannot be called. pl fpe mgrds gets called instead.(SCGCQ00566133 port of SCGCQ00457412 )  
  - Invader: pl tbm reg display's the wrong description. It should not say "Show FPE register"(SCGCQ00566134 port of SCGCQ00457414 )  
  - Discovery Event 0x90 when resetting all expander PHYs(SCGCQ00566148 port of SCGCQ00462914 )  
  - it_min build fails due to warning of unused variables(SCGCQ00566155 port of SCGCQ00469968 )  
  - PL: Fault 0x6001 while running heavy IOs and performing cable break of the initiator port.(SCGCQ00566162 port of SCGCQ00479492 )  
  - Fixed Issue with SATL Translation of SCSI Unmap Command(SCGCQ00566164 port of SCGCQ00480302 )  
  - PL: SATL does not send ATA Verify command during SCSI REASSIGN BLOCKS command(SCGCQ00566169 port of SCGCQ00484062 )  
  - PL Host Based Discovery: DataBolt Settings fail to take effect(SCGCQ00566176 port of SCGCQ00488529 )  
  - Fixed Issue with SATL Translation of SCSI Write Buffer Command(SCGCQ00566177 port of SCGCQ00490755 )  
  - Data Corruptions on Cobra C1 (no impact on SAS drives(SCGCQ00566178 port of SCGCQ00490921 )  
  - Fault 0x5851 during Destructive Domain test (Bobcat setup .(SCGCQ00566181 port of SCGCQ00494410 )  
  - PL: Query Task Doesn't Check for its Taskmid on FPE Exception Queue(SCGCQ00566189 port of SCGCQ00518804 )  
  - Fixed Issue in Fast Path Engine Manager State Machine Causing SATA IO Timeouts After Target Reset(SCGCQ00566196 port of SCGCQ00527860 )  
  - Valid flag for querying internal temperature sensor(SCGCQ00566217 port of SCGCQ00419361  )  
  - Enclosure/Slot based re-ordering of SAS Topology List Event(SCGCQ00566231 port of  SCGCQ00472198)  
  - Check iopiMemoryMove(  Return Status - SATL Mode Select, Read/Write Buffer, Log Select Commands(SCGCQ00566234 port of SCGCQ00472375 )  
  - Check iopiMemoryMove(  Return Status - SATL Log Sense, SMART Commands(SCGCQ00566235 port of SCGCQ00473154 )  
  - Check iopiMemoryMove(  Return Status - SATL Persistent Reserve Out, Read Media Serial Number, Reassign Blocks Commands(SCGCQ00566239 port of SCGCQ00473841 )  
  - Added Flush Write in Hardware Cleanup Code(SCGCQ00566240 port of SCGCQ00475639 )  
  - Check iopiMemoryMove(  Return Status - Rx Context Manager Interrupt Handler(SCGCQ00566245 port of SCGCQ00477144 )  
  - Check iopiMemoryMove(  Return Status - SSP Frame Received(SCGCQ00566252 port of SCGCQ00477836 )  
  - PL: Limit the Serdes temperature sensitivity workaround to 12G only(SCGCQ00566254 port of SCGCQ00478534 )  
  - Invader: Remove A0 support in firmware(SCGCQ00566260 port of  SCGCQ00488494)  
  - Allow users to select Transmitter Training preset in NVDATA(SCGCQ00566264 port of SCGCQ00501485 )  
  - PL: Flush Writes in TRx Transport Hardware Cleanup to Ensure Robustness(SCGCQ00566270 port of SCGCQ00522360 )  
  - Invader C0: (PL  0x6003 fault During TM and IO in Linux(SCGCQ00568123 port of SCGCQ00448659 )  
  - Update comments above PL prints for all the SATA files(SCGCQ00568408 port of SCGCQ00441329 )  
  - Modify a TxDma clean up print to show more info(SCGCQ00568423 port of  SCGCQ00501705)  
  - SAS2 IT - Phase 17 – "Device Present" Flag of SAS Device Page0 is not Set for Initiator Controller in Target Mode Controller(SCGCQ00568484 port of SCGCQ00449767 )  
  - Incorrect sense info obtained for a Request sense command during Read IO's(SCGCQ00568497 port of SCGCQ00448886 )  
  - SAS2IT: Incorrect SAT translation observed when sending a Security IN command with zero Allocation length with INC_512=1(SCGCQ00568500 port of SCGCQ00452375 )  
  - VALID Bit and INFORMATION Field are Not Handled in Sense Data for failing WRITE AND VERIFY Command(SCGCQ00568502 port of SCGCQ00455555 )  
  - SAS2 IT - Phase 17 – "Device Present" Flag of SAS Device Page0 is not Set for Initiator's Controller in SAS Topology(SCGCQ00568503 port of SCGCQ00462765 )  
  - Fixed SATA Passthrough Non-Auto IO Timeout(SCGCQ00596634 port of SCGCQ00570909 )  
  - Fixed Simple Coding Issue Leading to 0x6230 Fault(SCGCQ00675425 port of SCGCQ00643835 )  
  - Fault 6230 While Disabling Expander Phys and Running Stress in Multi-Path Failover Environment(SCGCQ00698228 port of SCGCQ00692652 )  
  - Fault 0x6230 While Running Heavy IOs and Cable Breaking(SCGCQ00698229 port of SCGCQ00669775 )  
  - PL: Target Mode performance improvements(SCGCQ00711575 port of SCGCQ00686570 )  
  - PL: Trace Buffer Manager performance improvements(SCGCQ00711576 port of SCGCQ00685828 )  
  - PL Fault 0x5851 is seen when running Query Task(SCGCQ00724357 port of SCGCQ00715239 )  
  - 0x6828 fault when using large CDB(SCGCQ00725157 port of SCGCQ00580326 )  
  - Target Mode: Task IU is sent to the IOP before it knows about the Initiator(SCGCQ00725158 port of SCGCQ00606248 )  
  - Internal Device Reset storm after controller reset using Long CDB.(SCGCQ00725161 port of SCGCQ00626891 )  
  - Change SATL handling for SCSI Format command to issue Write DMA Ext instead of Write FPDMA(SCGCQ00725163 port of SCGCQ00660847 )  
  - 12G SAS BC train fails with 6M cable between Fury and Cobra(SCGCQ00725164 port of SCGCQ00678053 )  
  - PL: Identify SSD firmware faults with code 0x4203(SCGCQ00725169 port of SCGCQ00702760 )  
  - PL: Identify SSD topology restrictions cause fault 0xD10F when device access is disabled(SCGCQ00725170 port of SCGCQ00702988 )  
  - PL: Identify SSD feature blocks IOs when DMD starts, not DMD ends(SCGCQ00725171 port of SCGCQ00705318 )  
  - PL: Identify SSD feature on SATA drives could cause discovery failures(SCGCQ00725172 port of SCGCQ00707367 )  
  - PL: Incorrect use of IOP LogInfo code(SCGCQ00725173 port of SCGCQ00709517 )  
  - PL: Topology restriction IO blocking should return a SCSI IO error(SCGCQ00725177 port of SCGCQ00706229 )  
  - PL: Topology restrictions should wait for the entire topology to be discovered(SCGCQ00725178 port of SCGCQ00707329 )  
  - PL: Low read/write throughput for SATA when interspersed with non-automated commands.(SCGCQ00725185 port of SCGCQ00666811 )  
  - pl SATL: Incorrect SAT error translation observed during Writesame command execution(SCGCQ00725203 port of SCGCQ00501272 )  
  - Information field is incorrectly populated for Verify command when accessing out of range LBA(SCGCQ00725205 port of SCGCQ00501346 )  
  - SATL: WRITE SAME Handling with LBPRZ=1, UNMAP=1, ANCHOR=0 needs an additional check(SCGCQ00725207 port of SCGCQ00524994 )  
  - PL: Reduce IOC Link Up Initialization Time(SCGCQ00725208 port of SCGCQ00414458 )  
  - Invader C0: Incorrect sense info obtained for a Request sense command during Read IO's sent to Fast Path Engine(SCGCQ00725223 port of SCGCQ00480300 )  
  - PL: Expander route tables not configured the same as with Self Configuring Expanders(SCGCQ00725227 port of SCGCQ00529543  )  
  - PL: EDFBMaxGroupUnload should be configured even when EDFB is disabled(SCGCQ00725228 port of SCGCQ00530731 )  
  - Uart function to access starfish register is broken(SCGCQ00725232 port of SCGCQ00564809 )  
  - Invader C0: MPI PM Global Request Change to Reduced or Standby state results in "Operation State Not Supported" or "IOC Busy"(SCGCQ00725237 port of SCGCQ00584284 )  
  - Fault 0xD071 while running stress and glitching all 4 phys(SCGCQ00725242 port of SCGCQ00590502 )  
  - Extra byte of data is provided when Inquiry command is issued for "Supported VPD Pages VPD Page" to a SATA Drive(SCGCQ00725248 port of SCGCQ00601768 )  
  - PL: Missing compile-in conditions for WA specific strings(SCGCQ00725251 port of SCGCQ00602540 )  
  - Fixed Problem in RxDMA Credit Leak Hardware Workaround(SCGCQ00725252 port of SCGCQ00602691 )  
  - Fixed Issue in Transport Layer Retries Code Causing 0x265D and 0x0501 Faults(SCGCQ00725256 port of SCGCQ00609576 )  
  - Need a method to disable PL Light print in IO path(SCGCQ00725259 port of SCGCQ00632446 )  
  - PL: Support Checking of iopiMemoryMove(  Return Status in plFailScsiIoWithCheckCondition((SCGCQ00725271 port of SCGCQ00477832 )  
  - DFE tuning(SCGCQ00725276 port of SCGCQ00505626 )  
  - SATL: Implemented Power Condition VPD Page (0x8A  for Inquiry Command(SCGCQ00725278 port of SCGCQ00524989 )  
  - Compile out unnecessary debug strings(SCGCQ00725285 port of SCGCQ00604550 )  
  - PL: Update some RxCM register definition(SCGCQ00725304 port of SCGCQ00650116 )  
  - PL: New commands useful for debugging(SCGCQ00725309 port of SCGCQ00228558 )  
  - PL: SATL Firmware doesn't return sector count in status return descriptor properly for non-data transfer ATA passthrough commands(SCGCQ00725315 port of SCGCQ00692885 )  
  - ATA Translation of sector count in sense data is inconsistent for READ DMA pass-through cmd(SCGCQ00725316 port ofSCGCQ00712688  )  
  - Unsupported SCSI Command fails with Incorrect Sense Data When SATA Drive is in Standby Power Condition(SCGCQ00725328 port of SCGCQ00654721 )  
  - PL: PortWidth field in SAS Port Page 0 is incorrect(SCGCQ00725336 port of SCGCQ00622522 )  
  - Fixed multiple order of operation bugs(SCGCQ00725346 port of SCGCQ00626966 )  
  - SR-IOV: Devices invisible to VF are listed in SAS IO Unit Page 0(SCGCQ00725349 port of SCGCQ00661386 )  
  - PL: Add fault code to indicate coding error in cable management code(SCGCQ00725358 port of SCGCQ00668692 )  
  - PL fault 0xD073 while running IOs(SCGCQ00725362 port of SCGCQ00628654 )  
  - Inquiry SCSI Command is Not Failed with Expected Response When NACA bit in Control Byte is set during During Format(SCGCQ00725376 port of SCGCQ00649572 )  
  - RAID Flags and CDB fields are corrupted after Fast Path Engine rejects FastPath ATA NATIVE COMMAND(SCGCQ00725383 port of SCGCQ00584505 )  
  - PL: Poll for parity error in FPE PLB Slave(SCGCQ00725388 port of SCGCQ00645401 )  
  - PL: Sata passthrough I/Os could complete before firmware cleans up the hw(SCGCQ00762562 port of SCGCQ00447782 )  
  - Fix build(SCGCQ00781297 port of SCGCQ00702695 )  
  - PL: Fix Target command free VPID base address structure definition(SCGCQ00781299 port of SCGCQ00704511 )  
  - PL: Fix how some prints spell "event"(SCGCQ00781302 port of SCGCQ00718795 )  
  - IOP: Force sequence point evaluation(SCGCQ00781306 port of SCGCQ00728929 )  
  - Verify (16  SCSI Command is Not Failed with Expected Response When Specified LBA Exceeds the Capacity of the Medium(SCGCQ00781319 port of SCGCQ00703423 )  
  - WRITE SAME(10  and WRITE SAME(16  SCSI commands are not working for the last LBA of SATA Drive(SCGCQ00781320 port of SCGCQ00703433)  
  - Fault 0x4203 When WRITE AND VERIFY (16  Command Is Executed to SATA Drive For LBA Out of Range(SCGCQ00781324 port of SCGCQ00705320 )  
  - During SATA Drive Format or self test, One Extra Byte of Data is Provided When Inquiry VPD "Supported VPD Pages VPD Page" is requested(SCGCQ00781325 port of SCGCQ00706016 )  
  - During SATA Drive Format or self test, firmware does not handle Allocation Length of zero for INQUIRY SCSI Command Properly(SCGCQ00781327 port of SCGCQ00706055 )  
  - Incorrect VPD Data is Obtained for VPD Page 0xB0 and 0xB2 When Drive is Under Foreground Extended Self-Test(SCGCQ00781328 port of SCGCQ00706063 )  
  - Read/Write 16 or 32 commands are Not Failed with Descriptor Format Sense Data when LBA is greater than 4 bytes.(SCGCQ00781330 port of SCGCQ00706963 )  
  - Unsupported POWER CONDITION Field in SCSI Start Stop Unit Command Not Failed with Check Condition(SCGCQ00781333 port of SCGCQ00710138 )  
  - Additional sense:Invalid cmd opcode, when read cmd sent to SATA drive in standby mode(SCGCQ00781339 port of SCGCQ00711813 )  
  - Fault 1901 Seen When Running Unmap IO’s During Task Aborts For a SATA Drive(SCGCQ00781340 port of SCGCQ00711858 )  
  - SATL doesn't handle ATA Pass-through (16  properly when Extend bit is cleared(SCGCQ00781348 port of  SCGCQ00715484)  
  - PL: Fix minor code issues found by analysis tool(SCGCQ00781349 port of SCGCQ00728016 )  
  - PL: Uninitialized variable being used in PL SATL Function(SCGCQ00781350 port of SCGCQ00728091 )  
  - PL: Firmware could be using uninitialized pointers in SGPIO error cases(SCGCQ00781360 port of SCGCQ00728894 )  
  - PL: SAS Topology Change List Event could send indeterminate ExpanderStatus(SCGCQ00781363 port of SCGCQ00729597 )  
  - PL: Firmware could be accessing null pointer in port layer interrupt handler.(SCGCQ00781369 port of SCGCQ00730721 )  
  - PL: Transport Layer Retry code was using a wrong value for a comparison(SCGCQ00781374 port of SCGCQ00731663 )  
  - PL: clear interrupt when AWT hits max value(SCGCQ00781381 port of SCGCQ00644555 )  
  - PL Target Mode: Implement multi reply queue handling of command buffers(SCGCQ00781392 port of SCGCQ00709549 )  
  - 0x58A1 fault occurs on partner controller while issuing MUR to a target mode controller with outstanding IOs(SCGCQ00781401 port of SCGCQ00680151 )  
  - Update PL firmware to have capability to not fault on Rx/Tx DMA engine SYS_DMA error(SCGCQ00785193 port of SCGCQ00678819 )  
  - PL: SATA code should check the return value of the function call(SCGCQ00793912 port of SCGCQ00736838 )  
  - PL: TLR: Tape drive backup could fail(SCGCQ00793921 port of SCGCQ00731689 )  
  - PL: PL code is not checking the return value of a function call(SCGCQ00793924 port of SCGCQ00736833 )  
  - PL: PL code is not checking the return status of a function call(SCGCQ00793925 port of SCGCQ00737080 )  
  - PL: Target mode code is not checking the return status of a function call(SCGCQ00793926 port of SCGCQ00737139 )  
  - PL: Task Management code is not checking the return status of a function call(SCGCQ00793927 port of SCGCQ00738131 )  
  - PL: Firmware is not checking the return status of a function when reading device page 0(SCGCQ00793929 port of SCGCQ00750552 )  
  - Target Mode performance improvements(SCGCQ00793943 port of SCGCQ00698205 )  
  - PL: Trace Buffer Manager add entry algorithm improvement(SCGCQ00793947 port of SCGCQ00740643 )  
  - PL: Yellow LED Function Code control LEDs using MfgPage13 for link up and link speed(SCGCQ00793949 port of SCGCQ00741955 )  
  - PL: SATA Spinup Hinting(SCGCQ00793954 port of SCGCQ00767301 )  
  - SES Page 0Ah Element Index mapping support for enclosure(SCGCQ00816410 port of SCGCQ00791963 )  
  - PL: Fault 0xD203 observed while releasing Diag Buffer (TRACE(SCGCQ00816415 port of SCGCQ00792742 )  
  - WW PL: Add MPI PCIe Device driver(SCGCQ00832573 port of SCGCQ00795210 )  
  - Tiger WW: Add Storage Expansion Device interrupt handler and initialization(SCGCQ00837237 port of SCGCQ00797527 )  
  - Tiger WW: Change how remote SAS core interrupts are handled(SCGCQ00837761 port of SCGCQ00798076 )  
  - PL: Controller could fault with 0x4A00 during link breaker test(SCGCQ00840579 port of SCGCQ00793956 )  
  - Tiger WW: Update SED MPI messages to 0.2 revision(SCGCQ00841600 port of SCGCQ00831478 )  
  - Certain drive pull scenarios result in longer time to discovery running than normal(SCGCQ00843979 port of SCGCQ00842344 )  
  - PL: Firmware should return an error if an invalid slot number is sent in a MPI SEP request(SCGCQ00848133 port of SCGCQ00824715 )  
  - PL: Firmware adjust external enclosure slots using StartSlot(SCGCQ00848135 port of  SCGCQ00824739)  
  - Incorrect IOCStatus status for SATA IOs during task management(SCGCQ00848141 port of SCGCQ00762311 )  
  - PL: Mode sense command with mode page 4 does not return proper Medium Rotation Rate (SATA(SCGCQ00848144 port of SCGCQ00811739 )  
  - PL: Target Status Send request doesn't get a reply and cause Target mode I/O timeout(SCGCQ00848146 port of SCGCQ00814468 )  
  - PL: Tweak conditions where the SMP Timeout Discovery Error gets reported(SCGCQ00851656 port of SCGCQ00840239 )  
  - 9300-8i- SATA SSDs in Locked State Not Showing Up After Manually Loading Driver.(SCGCQ00859103 port of SCGCQ00843668 )  
  - PL: SATA hinting feature causes IO timeouts with Linux(SCGCQ00868405 port of SCGCQ00867345 )  
  - Gen-3 is not supporting SES Page 0x0A slot mapping mode fully(SCGCQ00872845 port of SCGCQ00855132 )  
  - System Hangs after Adapter reset with heavy IO load(SCGCQ00875779 port of SCGCQ00646625 )  
  - PL: Check in Intruder A1 serdes setting(SCGCQ00882320 port of SCGCQ00882269 )  
  - PL: Fix FPE state machine transition flaw which could cause long I/O latency(SCGCQ00885561 port of SCGCQ00884179 )  
  - PL: Fault 0xd071 while sending ABORT_TASK TM using UART CLI(SCGCQ00890279 port of SCGCQ00877710 )  
  - PL: SATA Non-Automated IO Timeouts(SCGCQ00891852 port of SCGCQ00881787 )  
  - PL: Cleanup discovery code for improved maintainability(SCGCQ00894149 port of SCGCQ00872750 )  
  - Fixed issue where 19th entry of Self-Test Results Log Page was not showing during SAT translation.(SCGCQ00894173 port of SCGCQ00847941 )  
  - PL: SR-IOV: Add code to work around IO Accelerator HW issue(SCGCQ00894174 port of SCGCQ00854562 )  
  - PL: Fault 0x4300 During Discovery Error Recovery Testing (Parent Defect(SCGCQ00894175 port of SCGCQ00860398 )  
  - BUSY TIMEOUT PERIOD Field is incorrectly populated in Control Mode Page for SATA Drive(SCGCQ00894176 port of SCGCQ00871463 )  
  - During SATA FORMAT Operation, REQUEST SENSE Command is Not Failed with Expected Response Where DESC bit is Set As 1.(SCGCQ00894177 port of SCGCQ00872727 )  
  - New pliControlRequest to clear FPE bit in FPE flags of mid state table(SCGCQ00894180 port of SCGCQ00817050 )  
  - Print Indices are Messed up(SCGCQ00895287 port of SCGCQ00892192 )  
  - PL: PL fault 0xD115 during internal testing(SCGCQ00907122 port of SCGCQ00860462 )  
  - Cutlass A1: 0x681E fault while doing Cable breaking on I/T Switching(SCGCQ00907376 port of SCGCQ00902077 )  
  - Cutlass A1: Add debug prints in SSP Frame received error handling in firmware(SCGCQ00907378 port of SCGCQ00907230 )  
  - PL: Fault 0x5833 When Performing Controller Reboots(SCGCQ00908647 port of SCGCQ00888103 )  
  - PL: EnclMgmt: Fix slot assignment to direct attach SEP Device Handle(SCGCQ00909943 port of SCGCQ00894230 )  
  - PL Fault 0x6002 When Sending SCSI Security Protocol Out Commands to SATA SSDs(SCGCQ00910189 port of SCGCQ00888033 )  
  - PL: SAS Device Page 0 Entry Device Present for missing expander after Discovery Complete(SCGCQ00910604 port of  SCGCQ00904470)  
  - PL: EEDPDataOffset value is 0 in the Reply Message frame, while IOCStatus refers to DIF/EEDP check failure.(SCGCQ00913149 port of SCGCQ00900221 )  
  - PL: Use Dual Contexts in Tx Context Manager Only When Expanders Are Present(SCGCQ00918136 port of SCGCQ00419356 )  
  - PL SATL: SCSI ATA Passthrough Code Should Check For Correct CDB Length(SCGCQ00926753 port of SCGCQ00915201 )  
  - PL: Consecutive Port numbering when all phys in static configuration results in drives not being removed from topology(SCGCQ00930631 port of SCGCQ00916882 )  
  - SES command locate not working for IBM enclosure when slot number information source bit set which uses the SES page 0x0A mapping.(SCGCQ00933996 port of SCGCQ00915737 )  
  - SSD Marked Failed After Encountering 03/1100 Sense (Medium Error(SCGCQ00949612 port of SCGCQ00933048 )  
  - Gemini PL firmware inorrectly selects the backplane slots to update the drive status.(SCGCQ00988412 port of SCGCQ00966714 )  
  - PL: 0x670A fault when running heavy MR I/O on JBOD + TM reset(SCGCQ01000516 port of SCGCQ00945848 )  
  - PL Fault 0x6001 while formatting drives that support Send/Receive FPDMA QUEUED commands(SCGCQ01004147 port of SCGCQ00936413 )  
  - PL: Fault 26B5 while running destructive domain test(SCGCQ01004871 port of SCGCQ00911520 )  
  - PL: 0x4300 fault when running Cable Breaker port break between expanders(SCGCQ01004881 port of SCGCQ00941569 )  
  - PL: Initiator/target moved can result in Initiator missing event but no corresponding Target missing event(SCGCQ01005020 port of SCGCQ00915308 )  
  - TM-Target Reset with Srst for sata drives does not have TM_NOT_SUPPORTED set(SCGCQ01020751 port of SCGCQ00188243 )  
  - SMR Host Aware and Host Managed drive support & ZBC to ZAC SATL(SCGCQ01025897 port of SCGCQ00900453 )  
  - PL: SATL Translation of SCSI Write Buffer Modes 5 and 7 Incorrectly Sets FWFlags_NonAuto bit in HW Context(SCGCQ01039154 port of SCGCQ00897934 )  
  - Rebuild/Locate (Amber  LED is not blinking at the rate expected rate.(SCGCQ01046432 port of SCGCQ01028986 )  
  - Activity LED with Invert Activity is not blinking corresponding to the IO operations(SCGCQ01046433 port of SCGCQ01028990 )  
  - PL: CONNECTOR_INFO structure misaligned and Failure to read IO Unit Page 7(SCGCQ01059529 port ofSCGCQ01055132  )  
  - PL: Fault 0xD073 during heavy IO(SCGCQ01059925 port of SCGCQ01052686 )  
  - To support non-contiguous slot numbers defined in Manufacturing page 7.(SCGCQ01061903 port of SCGCQ01000709 )  
  - SMR : Implement PARTIAL bit option for ReportZones command as part of ZBC-ZAC SATL(SCGCQ01070851 port of SCGCQ01020836 )  
  - PL's SATL fixes to SCSI Write Buffer modes 0xD, 0xE, and 0xF(SCGCQ01073648 port of SCGCQ01067662 )  
  - Non-zero check for LUN field in commands that SAM specifies to return ILLEGAL REQUEST(SCGCQ01080494 port of  SCGCQ01073728)  
  - To assign the enclosure level index for direct attached enclosures ie., the controller itself.(SCGCQ01084605 port of SCGCQ01057508 )  
  - SATA Only: Power On Reset Observed While Executing LOG SENSE Command to SATA Drive.(SCGCQ01085644 port of SCGCQ01081163 )  
  - PL: CPU hang due to out of bound access of Timer wheel RAM while manually adding FPE timer.(SCGCQ01090982 port of SCGCQ01089094 )  
  - PL Fault 0x584F (MID validation failure  when Timer Reached and Non Auto Frame interrupts are seen together.(SCGCQ01090985 port of SCGCQ01049209 )  
  - Return EEDP/DIF error data of the first error frame detected by the hardware during READ in the MPI Reply error message frame(SCGCQ01092128 port of SCGCQ01000193 )  
  - PL: Discovery due to non responding SATA drive is now timed to last for the amount of seconds configured in NVDATA(SCGCQ01092176 port of SCGCQ00996678 )  
  - PL: SMR Report Zone Command was not failed for last LBA only(SCGCQ01117871 port of SCGCQ01113946 )  
  - PL: System Halt with Certain Expander Backplanes(SCGCQ01123049 port of SCGCQ01116427 )  
  - PL: Customer expansion enclosures are seeing large number of drive timeout(SCGCQ01123282 port of SCGCQ01118894 )  
  - PL: 0x5813 and 0x5814 Faults after implementing a hardware workaround(SCGCQ01144861 port of SCGCQ01143329 )  
  - PL: Support for all the Internal connector types to end devices defined in the SES3 specification revision 13d and the proposed new connectors for SAS4(SCGCQ01167211 port of SCGCQ01085063 )  
  - PL:SCT Write Same support on native 4K drives(SCGCQ01168729 port of SCGCQ01163873 )  
  - PL: Green LED remains ON when direct attached drives are removed(SCGCQ01177453 port of SCGCQ01149961 )  
  - SATL Only: Write Same SCSI Command Fails With CC for SATA Drive(SCGCQ01180893 port of SCGCQ01173592 )  
  - Link rate reports as unknown for SAS3216/SAS3224 when PHY is disabled(SCGCQ01181861 port of SCGCQ01180830 )  
  - MR_6.12_SDS_Replan : FW disables FP for SED/FDE JBOD (epd passthrough .(SCGCQ01198915 port of SCGCQ01135893 )  
  - PL: Fault 0x6003 hits if blocked device has IOs pended before it gets blocked(SCGCQ01204822 port of SCGCQ01185613 )  
  - PL fault 5854 seen when system boots with all SATA drives in setup spun down(SCGCQ01204854 port of SCGCQ01155407 )  
  - Linux MR-Intruder-6.12-Replan-Beta:Performance drop of -20% SR, 8K-IO Size,QD(256  RAID-10 6G SATA-HDD x16DC(SCGCQ01205607 port of SCGCQ01171907 )  
  - Ventura PL: Add support to existing pli control request to do additional PL housekeeping for a stale MID(SCGCQ01209109 port of SCGCQ01204327 )  
  - SATA Only: WriteSame command aborts on 4K drive(SCGCQ01220119 port of SCGCQ01219893 )  
  - PL: Support slot numbers starting at an arbitrary number(SCGCQ01221523 port of SCGCQ01211733 )  
  - To fix 6.13 Fw coverity issues #15354, #15370 , #15442, #15745, #15755, #16014, #18206, #18327(SCGCQ01236424 port of SCGCQ01209604 )  
  - PL: Updates to temperature calibration(SCGCQ01243581 port of SCGCQ01241696 )  
  - Ventura: Firmware Hangs on Cold Boot of Slow Parts(SCGCQ01251642 port of SCGCQ01250734 )  
  - Locate operation to a drive in UEFI HII may fail to locate the drive(SCGCQ01255902 port of SCGCQ01255279 )  
  - SGPIO clock running at 100.7 KHz when set to 100Khz(SCGCQ01260750 port of SCGCQ01234457 )  
  - Firmware halts upon changing controller personality to JBOD mode with MCTP enabled(SCGCQ01260886 port of SCGCQ01252243 )  
  - PL Fault 0x5813 caused during SEND FSM TIMEOUT interrupt handling(SCGCQ01263723 port of SCGCQ01253195 )  
  - PL: SATA drive can't be detected after SPL-2 power compliant SAS drive is removed from same PHY(SCGCQ01269103 port of SCGCQ01264525 )  
  - PCIE discovery may complete early with no drives discovered before backplane detection is complete(SCGCQ01270117 port of SCGCQ01269316 )  
  - NVMe backplane detection and device discovery fails on OEM specific server NVMe backplane(SCGCQ01278820 port of SCGCQ01274101 )  
  - PL : Add Support for PUIS(Power Up In Standby  SATA drives(SCGCQ01280342 port of SCGCQ01174618 )  
  - Infinite loop on DISM when FW gets timeout for READ CAPACITY command (Porting to 6.x(SCGCQ01282807 port of SCGCQ01015624 )  
  - Ventura: Backplane detection logic may not initiate the second I2C write to Backplane device(SCGCQ01284634 port of SCGCQ01284607 )  
  - SBR reload is not working when update to new ROP which have new SBR and do warm reboot(SCGCQ01286949 port of SCGCQ01279081 )  
  - Support for 8GB DDr (SCGCQ01287322 port of SCGCQ01254692 )
  - bladeErrorIsrTask ChanNum 0 intStatus hit while enabling security in intruder(SCGCQ01287771 port of SCGCQ01077578 )  
  - MR 7.0.1: iMR FW hangs after rebuild is started on a hotspare drive that's been reclaimed(SCGCQ01293858 port of SCGCQ01286579 )  
  - Storclif returns failure with Description "Corrupted Image" when user tries to flash any other package(SCGCQ01293860 port of SCGCQ01292507 )  
  - Series of OCR seen during media recovery; System hangs during boot after AC cycle(SCGCQ01305737 port of SCGCQ01284753 )  
  - Ventura: Locate operation to a slot in a VPP backplane may not turn ON the LED(SCGCQ01312144 port of SCGCQ01308356 )  
  - LED does not turn OFF when PD is removed .(SCGCQ01314611 port of SCGCQ01003387 )  
  - PL:Customer specific drive enumeration(SCGCQ01315240 port of SCGCQ01198341 )  
  - MARS OEM branded iMR 9440-8i card randomly blinks Error/Fault LEDs on OEM backplane during VD Full initialization(SCGCQ01316648 port of SCGCQ01310542 )  
  - MR7.2_NVMe: FW Kill Adapter observed, after degrading R6 Dual Core Capable VD'(SCGCQ01316893 port of SCGCQ01306918 )  
  - 'C0:mr_wakeup: mem 45569e20, cache line ffffffff' observed while running BGI on RAID 5 Volume with media errors.(SCGCQ01317866 port of SCGCQ01256120 )  
  - MR_6.11_FW: Data corruption seen on IMR controller on JBOD with raw IO using smash tool- sles OS(SCGCQ01322090 port of SCGCQ00994097 )  
  - Cache Data lost if power loss happens during descriptor preparation.(SCGCQ01322093 port of SCGCQ01253076 )  
  - Data corruption on R6 WB VD when there are medium errors on one PD(SCGCQ01322143 port of SCGCQ01314319 )  
  - IMR_6.13: Drive is not marked as Foreign upon OCR when controller already has max configured PD's(SCGCQ01322224 port of SCGCQ01163849 )  
  - Design changes update on NVME drive hotswap feature and updating more changes(SCGCQ01327717 port of SCGCQ01319426 )  
  - RDM in Use-RDm Error & crashed into Montask during boot(SCGCQ01328766 port of SCGCQ01147739 )  
  - MR_6.11_FW: Data corruption seen on IMR controller on JBOD with raw IO using smash tool- sles OS(SCGCQ01328975 port of SCGCQ00994097 )  
  - Firmware hit PL Fault 0000d033 when pull out multiple drives (OEM backplane(SCGCQ01330783 port of SCGCQ01304715 )  
  -  Port_Not_Required  port of  ) MR 7.1_Double Dip COL causes loss of disk cache(SCGCQ01334524 port of SCGCQ01311127 ) 
  - pl: backend PCIe: specific vendor NVMe device does not appear to host software(SCGCQ01337626 port of SCGCQ01328743 )  
  - Port_Not_Required  port of  ) Revert C(SET (SCGCQ01318920(SCGCQ01339727 port of  SCGCQ01338907)  
  - Ventura: Detect invalid BP_TYPE types in VPP backplane Mgmt connector group(SCGCQ01342775 port of SCGCQ01332062 )  
  - (NVMe Only  Some SCSI IOs to NVME devices with IEEE SGL failed with invalid SGL IOC Status(SCGCQ01343513 port of SCGCQ01325987 )  
  - Cisco Validation: FW throws an exception while scheduling Consistency check on R1.(SCGCQ01344416 port of SCGCQ01339131 )  
  - Ventura MR - Linux 64 JBOD SAS HDDs 4K SW 64QD controller crashes(SCGCQ01344432 port of SCGCQ01342194 )  
  - Remove DRAID sources(SCGCQ01346356 port of SCGCQ01346339 )  
  - Insertion of Faulty drive results in FW failure.(SCGCQ01346491 port of SCGCQ01321192 )  
  - Event Log API does not account for instances when LD ID may be set to LD_INVALID(SCGCQ01347025 port of SCGCQ01330761 )  
  - unwanted print in the tty log(SCGCQ01349266 port of SCGCQ01291928 )  
  - MR7.1: Unexpected event for lun not ready Sense: 2/04/02(SCGCQ01349291 port of SCGCQ01304550 )  
  - 9440-8i - system hung during stress test in JBOD mode under Win10(SCGCQ01356675 port of SCGCQ01341346 )  
  - CSCve49430(CSC.nuova,new,chrevana C240-M5:When all 26 drives inserted , drives discovery failure is observed.(SCGCQ01357951 port of SCGCQ01349506 )  
  - Ventura: PL FW may fault x720E for invalid backplane type configuration(SCGCQ01357973 port of SCGCQ01351358 )  
  - Set the appropriate ( DM_IO_CTX_FLAG_INT_CFG_REQ   flag to indicate that mptfarme/mid is allocated for internal config request so that frame will be released inside DmPlConfigPage after the allocation purpose is served.(SCGCQ01358260 port of SCGCQ01355519 )  
  - Firmware should block to downgrade MR 7.2 NVMe profile to MR 7.1 SAS/SATA profile(SCGCQ01361593 port of SCGCQ01357859 )  
  - LSA hangs when user try to change drive security key.(SCGCQ01370420 port of  SCGCQ01342655)  
  - Security Key provided for importing Foreign Config is not taken by LSA 02.79(SCGCQ01373223 port of SCGCQ01332191 )  
  - SSU Commands to SPL-2 compliant drive times out(SCGCQ01376408 port of SCGCQ01358769 )  
  - PL: RETURNED LOGICAL BLOCK ADDRESS in READ CAPACITY (16  is unexpectedly zero(SCGCQ01377235 port of SCGCQ01366977 )  
  - Chassis slot valid bit is not set into Enclosure Page 0.(SCGCQ01380979 port of SCGCQ01323680 )  
  - Dev defect:- to enhance the fix for graceful handling of MfgId 0 ONFI issue(SCGCQ01383726 port of SCGCQ01365188 )  
  - Fix synchronization issues with ttyLogInFlash=1(SCGCQ01385058 port of SCGCQ01378083 )  
  - Ventura B0: 9400 IT Channel product firmware detecting memory read error during bootup(SCGCQ01385670 port of SCGCQ01375470 )  
  - Cascaded x32 Backplane causing 100+ second retry during system boot(SCGCQ01391350 port of SCGCQ01385039 )  
  - Repeated SATA SSD erase cause FW hung(SCGCQ01396972 port of SCGCQ01391886 )  
  - Post discovery, if a SAS drive which is set as JBOD is spun down with sg_utils and fdisk(8  is run on Linux, creates a hang like situation(SCGCQ01396974 port of SCGCQ01393187 )  
						
  - Unable to use secondary upgrade Key.(SCGCQ01396976 port of SCGCQ01384568 )  
  - MR 7.3 :PL Fault 0000d075 LR 01283991 , while running IO`s , CC and OCR in background.(SCGCQ01399528 port of SCGCQ01384714 )  
  - Fix synchronization issues with ttyLogInFlash=1(SCGCQ01403256 port of SCGCQ01378083 )  
  - Replacing RAID Controller with Degraded VD Hangs System(SCGCQ01403725 port of SCGCQ01393703 )  
  - pdRef filled incorrectly in bvd->Physical_Disk_Sequence[] causing DDF to skip added PD in Recon(SCGCQ01412186 port of SCGCQ01400343 )  
  - Parameter Page Reads fail during ONFI bringup.(SCGCQ01415127 port of SCGCQ01413557 )  
  - Active  port of  ) Prevent Improper Flash from I(S(SI (Supported (SBR/FW to nonport of  )I(S(SI (Supported (SBR/FW when Board has I(S(SI Chip(SCGCQ01420659 port of SCGCQ01410666 ) 
  - Firmware doesn’t support VPD, so PCI VPD support should not be advertised(SCGCQ01439825 port of SCGCQ01392173 )  
  - System will pop up “Cannot communicate with iButton to …” during reboot with Dania card (FW:50.2.1-0597(SCGCQ01450218 port of SCGCQ01447988 )  
  - PL: EnclMgmt: Move ownership of SES Page 0x0A slot mapping from devices to PHYs(SCGCQ01458622 port of SCGCQ00870423 )  
  - NVMe drive discovery fails after pull/push on customer specific NVMe supported backplane(SCGCQ01460735 port of SCGCQ01404209 )  
  - Ventura B0: NVME Drives Not Discovered on 16i Card(SCGCQ01461753 port of SCGCQ01381033 )  
  -(SCGCQ01462850 port of SCGCQ01459442 )  
  - Hot plugged NVMe drive fails to link up on OEM backplanes with ISTWI drive presence polling enabled(SCGCQ01464096 port of SCGCQ01463496 )  
  - MR7.4: LDs disappear when changing controller profile (from profile 10 back to profile 12 .(SCGCQ01465007 port of SCGCQ01413560 )  
  - Fixed the issue with older ibutton(SCGCQ01466737 port of SCGCQ01455738 )  
  - Purley Server: CATERR reported on front panel LCD and SUT hang at the windows logo page(SCGCQ01481033 port of SCGCQ01410221 )  
  - MR RAID-mode profile 10 create vd cause pds for that vd offline(SCGCQ01481312 port of SCGCQ01450092 )  
  - BT1680: Constant ORR during test with SATA enclosure(SCGCQ00136973 port of SCGCQ00134862 )  
  - Devices are not present after returning from hibernation(SCGCQ00137695 port of SCGCQ00136646 )  
  - Duplicate MPI2_EVENT_SAS_INIT_DEVICE_STATUS_CHANGE with MPI2_EVENT_SAS_INIT_RC_ADDEDC_ADDED(SCGCQ00140409 port of SCGCQ00138171 )  
  - SEP transfers may fail on certain DA-SEP backplanes.(SCGCQ00143810 port of SCGCQ00143533 )  
  - SATA: read 16 with LBA greater than 48-bits returns success(SCGCQ00146091 port of SCGCQ00141435 )  
  - Reset loop after induced TM during IO(SCGCQ00148774 port of SCGCQ00145842 )  
  - Converting SATA Standby count to proper Standby condition timer value in Power condition mode page (page 0x1a  for mode sense command.(SCGCQ00148775 port of SCGCQ00145610 )  
  - plGetLBA(  should be inlined(SCGCQ00149235 port of SCGCQ00147434 )  
  - Add more info to pl status debug command(SCGCQ00152663 port of SCGCQ00147744 )  
  - Prevent false 0x6003 Faults(SCGCQ00153307 port of SCGCQ00146948 )  
  - LSI2008 SATA NCQ enablement(SCGCQ00153474 port of SCGCQ00142855 )  
  - Multiple Phy Counter Events being triggered for same Phy Counter(SCGCQ00153481 port of SCGCQ00149277 )  
  - Send Execute Device Diagnostic ATA command during SATA Initialization(SCGCQ00155108 port of SCGCQ00148227 )  
  - Initiator device removal request fails when no I/Os are outstanding(SCGCQ00155217 port of SCGCQ00144168 )  
  - bld: Change PL makefile to build one object at a time(SCGCQ00155428 port of SCGCQ00151669 )  
  - Initiator removal handling(SCGCQ00155465 port of SCGCQ00148025 )  
  - Unwarranted SAS TOPOLOGY CHANGE LIST EVENT with PhyStatus change indication(SCGCQ00156018 port of SCGCQ00150956 )  
  - Eliminate PL Config Page restrictions(SCGCQ00157819 port of SCGCQ00143162 )  
  - Firmware might fault with code 0x4300 during SATA device initialization(SCGCQ00160151 port of SCGCQ00155693 )  
  - SATL: Wrong tag reported when unable to determine tag(SCGCQ00160153 port of SCGCQ00153117 )  
  - DMA sense data with FW instead of HW to prevent a hang of the DMA transfer.(SCGCQ00160363 port of SCGCQ00155280 )  
  - Constant ORR after injecting a wrong-direction data frame(SCGCQ00160502 port of SCGCQ00149684 )  
  - Fault 6051 or Long TM response times for Target Resets(SCGCQ00160985 port of SCGCQ00158317 )  
  - The SEP on a specific enclosure is not being seen.(SCGCQ00162958 port of SCGCQ00153605 )  
  - 0x0614 fault when aborting SATA passthrough messages(SCGCQ00163555 port of SCGCQ00152992 )  
  - Tuning needed for SATA power management(SCGCQ00164715 port of SCGCQ00153107 )  
  - Detection of a PMC SATA Mux, and enablement of NCQ(SCGCQ00168598 port of SCGCQ00144305 )  
  - PM: Need to disable SAS link power mgmt due to outstanding HW issues(SCGCQ00169036 port of SCGCQ00157653 )  
  - Add debug prints for TM completion when TM is aborted by another TM(SCGCQ00170860 port of SCGCQ00142862 )  
  - Fault 5900 during Task Management with SATA drives.(SCGCQ00188487 port of SCGCQ00185016 )  
  - Event notification for NOTIFY(Enable Spinup(SCGCQ00188779 port of SCGCQ00161993 )  
  - Reception of Initiator Added event before host removed device from a previous Initiator Not Responding event(SCGCQ00189547 port of SCGCQ00179026 )  
  - Translated Format Unit error handling(SCGCQ00192672 port of  SCGCQ00180307)  
  - PL: SAS Topology Change List Event may return incorrect NumPhys data(SCGCQ00193236 port of SCGCQ00151741 )  
  - Good Status reported on write command (mid execution  terminated with Task Set Full during data transfer(SCGCQ00198309 port of SCGCQ00193386 )  
  - Fault 7C35 seen during READ DMA passthrough commands to SATA Drive(SCGCQ00201418 port of SCGCQ00188546 )  
  - (SRIOV-Only PL  Add new pli interface to create ADD or REMOVE events(SCGCQ00201464 port of SCGCQ00176747 )  
  - (SRIOV-Only PL  Modify PL handling of DevHandle-addressed pages(SCGCQ00203026 port of SCGCQ00176746 )  
  - ATAPI: Additional cleanup during task management(SCGCQ00203751 port of SCGCQ00191984 )  
  - PL: Update some internal structures for device discovery(SCGCQ00209572 port of SCGCQ00202359 )  
  - PL: Slot number in Device Page 0 may be incorrect(SCGCQ00218355 port of SCGCQ00193383 )  
  - PL: SMP Discover List requests may time out(SCGCQ00221727 port of SCGCQ00209329 )  
  - Alternate slot addressing fails with Discover response length 0x1C(SCGCQ00226950 port of SCGCQ00207622 )  
  - Invalid SATA frame received during SATA spinup will result in PL Fault(SCGCQ00237418 port of SCGCQ00205898 )  
  - The SATL's inquiry VPD page 0 doesn't show support for block limits and logical block provisioning pages.(SCGCQ00237489 port of SCGCQ00226980 )  
  - Port link status GPIO LED (Green, Yellow  support for individual controller PHY's(SCGCQ00249384 port of SCGCQ00222856 )  
  - Add support to disable automatically doing spin-up in NVData(SCGCQ00249385 port of SCGCQ00201709 )  
  - pl: SATA non read/write command may be delayed under low resource condition(SCGCQ00250273 port of SCGCQ00219989 )  
  - Add LogInfo data for SMP Passthrough Request(SCGCQ00254440 port of SCGCQ00201947 )  
  - 5881 fault occurs on certain errors after issuing debug command(SCGCQ00254459 port of SCGCQ00228952 )  
  - Custom HARD RESET behavior in Target Mode firmware(SCGCQ00255664 port of SCGCQ00198846 )  
  - On simulated Cable pulls, an expander goes missing but no add event is seen when the cables are replugged(SCGCQ00260441 port of SCGCQ00242899 )  
  - SATL: Configurable Write Same execution behavior(SCGCQ00260442 port of SCGCQ00245759 )  
  - Tbolt: Port width modulation changes(SCGCQ00261551 port of SCGCQ00165936 )  
  - SATL:Read capacity 16 lowest aligned high byte calculation is incorrect(SCGCQ00279895 port of SCGCQ00254497 )  
  - pl: Improve handling of SATA Device Fault errors during initialization(SCGCQ00281558 port of SCGCQ00232070 )  
  - SAS Phy error counters are not getting incremented on removing direct attached expander(SCGCQ00315209 port of SCGCQ00231068 )  
  - SAS2 IT - Phase 14 – When SATA Drive is Moved to Standby State via Mode Page(0x1a , ASC/ASCQ is Incorrect for REQUEST SENSE(SCGCQ00317906 port of SCGCQ00286160 )  
  - (Sata Only  Request Sense Command is showing incorrect data during stopped condition(SCGCQ00318905 port of SCGCQ00283334 )  
  - Open Timeout Error Handling is too drastic(SCGCQ00319955 port of SCGCQ00089824 )  
  - Unexpected link reset on Write Current of SAS IO Unit Page 1(SCGCQ00320037 port of SCGCQ00248535 )  
  - SAS2308 doesn't support DPO or FUA(SCGCQ00320040 port of SCGCQ00254531 )  
  - Dev handle reuse not prepoerly handled(SCGCQ00320063 port of SCGCQ00298766 )  
  - SAS2 IT - Phase 14 – Allocation Length for SCSI READ CAPACITY(16  Command is not Handled Properly(SCGCQ00320749 port of SCGCQ00286226 )  
  - Request Sense Command is showing incorrect data during Send Diagnostic foreground mode Command is issued.(SCGCQ00321663 port of SCGCQ00283700 )  
  - SAS2 IT : Phase 14 : Cannot abort a background short Self test(SCGCQ00323826 port of SCGCQ00285460 )  
  - 0x6051 Fault happens while doing cable pulls on expanders(SCGCQ00405927 port of SCGCQ00255115 )  
  - PL: Revert COMWAKE negation time to default value(SCGCQ00408859 port of SCGCQ00317288 )  
  - Invader B0: Add FLUSH_WRITEs to FPE timer handlers(SCGCQ00408890 port of SCGCQ00348342 )  
  - Debug Flags issue with non-IO path portion of the PL build(SCGCQ00414439 port of SCGCQ00327165 )  
  - Invader B0 configures externally configurable route table with invalid table-table route entries.(SCGCQ00418573 port of SCGCQ00340055 )  
  - SAS2 IT Ph 15: Incorrect Sense data is populated when Security Protocol IN/OUT command is sent to supported Drive(SCGCQ00433282 port of SCGCQ00334093 )  
  - SAS2 IT - Phase 15 – REQUEST SENSE's ASCQ is Incorrect When SATA Drive State Tranistion Happens (ie  Active->Standby->Stopped(SCGCQ00436152 port of SCGCQ00327531 )  
  - SAS link does not reverting to 6G when Tx Training failed and causes the link not to come up(SCGCQ00436190 port of SCGCQ00352330)  
  - Invader B0: 0x6003 fault during long term large IO test(SCGCQ00437119 port of SCGCQ00355980 )  
  - Invader: Fixed Problem with MoveTo/FromSasDCR(  Functions Being Incorrectly Called from PL(SCGCQ00445287 port of SCGCQ00362895 )  
  - PL: READ LONG and WRITE VERIFY commands to a SATA drive fail.(SCGCQ00459493 port of SCGCQ00374557 )  
  - Invader: Fixed SATA/Discovery Issue Where Discovery Retries are Exhausted and Cleanup is Not Performed(SCGCQ00460205 port of SCGCQ00358449 )  
  - 265D fault handling IO while SATA drive is not ready if SATA init fails(SCGCQ00461053 port of SCGCQ00344626 )  
  - pl: SATL: Improper Inquiry data for nonzero LUNs when a Format Unit is in progress(SCGCQ00461986 port of SCGCQ00333233 )  
  - (Sata Only  Fault (0x1901  Observed When VPD Inquiry is Executed When SATA Drive is Under Diagnostic Operations(SCGCQ00462588 port of SCGCQ00343690 )  
  - Add TM tracker to Mid tracker(SCGCQ00463061 port of SCGCQ00363000 )  
  - Target mode abort all IOs except Task IUs(SCGCQ00463241 port of SCGCQ00337985 )  
  - Invader C0: SGE flags incorrectly set during Rx DMA passthrough(SCGCQ00464630 port of SCGCQ00378949 )  
  - Invader: Added Debug Table to UART to Show Outstanding Task Management MIDs(SCGCQ00464637 port of SCGCQ00364238 )  
  - IR: Prevent IO to a phys disk while TM is in progress(SCGCQ00466020 port of SCGCQ00187983 )  
  - PL: Event Replay device reordering(SCGCQ00469721 port of SCGCQ00313918 )  
  - SAS2 IT - Phase 15 – Extra Bytes of Data Provided for REPORT LUNS SCSI Command with Allocation Length=0x10(SCGCQ00470268 port of SCGCQ00338263 )  
  - SAS2 IT - Phase 15 – Power Condition Mode Page Shows SATA Drive Standby Timer is Enabled At Start of Day(SCGCQ00470272 port of SCGCQ00335285 )  
  - Write same to SATA drive with UNMAP=1 and Number Of Logical Blocks = 0 fails(SCGCQ00470275 port of SCGCQ00343026 )  
  - Fixed Issue Involving 0x6004 Fault Caused by Incorrect Double Incr/Decrement of IO Count(SCGCQ00470944 port of SCGCQ00378928 )  
  - Invader B0: Update TBM Init and fix recursive D20E fault(SCGCQ00471576 port of  SCGCQ00367917)  
  - Fury B0: Fault D20C followed by a recursive D20E(SCGCQ00471578 port of SCGCQ00325990 )  
  - Invader C0: Use a reserved PL print during TBM initialization(SCGCQ00472138 port of SCGCQ00383616 )  
  - Added faults in the cable management code(SCGCQ00473937 port of SCGCQ00365524 )  
  - C0: Fix SAS Phy SerDes settings(SCGCQ00475433 port of SCGCQ00377552 )  
  - Invader: Update Workaround Descriptions to Include C0 on Affected or Fixed Line as Appropriate(SCGCQ00475792 port of SCGCQ00361713 )  
  - Enable cable management feature(SCGCQ00476590 port of SCGCQ00372021 )  
  - Serdes temperature sensitivity may cause phy errors(SCGCQ00476793 port of SCGCQ00384936 )  
  - Firmware faults with 0x2622 due to a parity error in pad (unused  data(SCGCQ00477177 port of SCGCQ00332124 )  
  - Invader C0: (PL  Incorrect workaround name in workaround implementation(SCGCQ00477179 port of SCGCQ00377271 )  
  - Update Serdes settings so the Transmitter Training takes shorter amount of time(SCGCQ00480609 port of SCGCQ00360460 )  
  - PL: SATL - Fix handling of Immediate bit.(SCGCQ00495886 port of SCGCQ00440204 )  
  - SATL: Unmap limits artifically limited to prevent OS timeouts(SCGCQ00498353 port of SCGCQ00382076 )  
  - PL: SCSI Mode Sense to ATA fails for Power Condition mode page.(SCGCQ00498889 port of SCGCQ00423683 )  
  - PL: Check iopiMemoryMove(  Return Status - SATL Read Capacity, Report LUNs, Security Protocol Commands(SCGCQ00500694 port of SCGCQ00422209 )  
  - Removed Unused Code in Device Manager(SCGCQ00501211 port of SCGCQ00401450 )  
  - PL: Check iopiMemoryMove(  Return Status - SATL Request Sense, Format, Mode Sense Commands(SCGCQ00501297 port of SCGCQ00425006 )  
  - Fixed Bugs in Parameter Data for SATL Translation of Security Protocol In Command(SCGCQ00503693 port of SCGCQ00447871 )  
  - PL: Certain PhyGroup configurations result in fault 0x7600(SCGCQ00528434 port of SCGCQ00404234 )  
  - Move all the one-second calls in the pl timer to a different function(SCGCQ00530329 port of SCGCQ00391042 )  
  - PL: modify PL_PRINTs in discovery code(SCGCQ00531113 port of SCGCQ00393414 )  
  - Fixed Minor Issue in UART Diagnostic Code Which Could Cause Data Exception(SCGCQ00531120 port of SCGCQ00407170 )  
  - Invader C0: Minor Target mode optimzations(SCGCQ00551042 port of SCGCQ00411657 )  
  - Invader C0: Power Management does not fill in TxRxSleepStatus field in SAS IO Unit Page 8(SCGCQ00555919 port of SCGCQ00406316 )  
  - PL: Use Dual Contexts in Tx Context Manager Only When Expanders Are Present(SCGCQ00556336 port of SCGCQ00419356 )  
  - IO aborts after a controller reboot from the surviving controller(SCGCQ00556337 port of SCGCQ00439506 )  
  - PL: Update RxLosvref value per SE(SCGCQ00559398 port of SCGCQ00415144 )  
  - make internal temperature sensor data available at start-of-day(SCGCQ00559404 port of SCGCQ00419450 )  
  - PL: Serdes temperature sensitivity workaround needs to be enabled for B0 chip as well(SCGCQ00565459 port of SCGCQ00417770  )  
  - cli command pl fpe mstap cannot be called(SCGCQ00566131 port of SCGCQ00457406 )  
  - Invader: pl fpe mgrdsfff does not allow EnableVFCheck to be set(SCGCQ00566132 port of SCGCQ00457408 )  
  - (PL  Implement workaround for BugTrack [SAS3Core]1101(SCGCQ00566154 port of SCGCQ00468537 )  
  - Invader C0: Fault 0x5854 During Jammer Error Injections(SCGCQ00566159 port of SCGCQ00472744 )  
  - Fixed Problem With SATL Translation of SCSI Unmap to SATA TRIM Command(SCGCQ00566184 port of SCGCQ00503015 )  
  - PL: Discovery fails to discover devices added during discovery(SCGCQ00566199 port of SCGCQ00556144 )  
  - PL: Update Host Based Discovery to include DataBolt settings(SCGCQ00566213 port of SCGCQ00414622 )  
  - Check iopiMemoryMove(  Return Status - Atapi SCSI IO, Handle IO During Format or Self Test(SCGCQ00566246 port of SCGCQ00477803 )  
  - Check iopiMemoryMove(  Return Status - Target Abort Command Buffers(SCGCQ00566250 port of SCGCQ00477834 )  
  - PL: Flush Writes and MemorySyncs in DMA Trans Queue and Rx Transport Hardware Cleanup to Ensure Robustness(SCGCQ00566269 port of SCGCQ00521686 )  
  - Create SAT3 Disabled Compile Option(SCGCQ00568403 port of SCGCQ00419844 )  
  - mpi_temp.h cleanup(SCGCQ00568424 port of SCGCQ00503059 )  
  - Incorrect Additional Sense data for PERSISTENT RESERVE OUT, when executed on Direct attach SATA drive(SCGCQ00568485 port of SCGCQ00454354 )  
  - Configurable SES Page Buffer Size(SCGCQ00568488 port of SCGCQ00342945 )  
  - Linux Driver mpt2sas failure observed during module load(SCGCQ00568493 port of SCGCQ00427369 )  
  - Security Protocol In with Security Protocol 0xEF does not retrieve the proper data(SCGCQ00568494 port of SCGCQ00443913 )  
  - PL: Internal structures associated with missing Initiator devices may not be removed(SCGCQ00568495 port of SCGCQ00446007 )  
  - SAS2 IT - Phase 17 – WRITE LONG(16  SCSI Command is Not Failed with Expected SCSI Response for Incorrect SERVICE ACTION field(SCGCQ00568499 port of SCGCQ00451090 )  
  - SCSIStatusQualifier is added to SCSI IO Error Reply(SCGCQ00568504 port of SCGCQ00397520 )  
  - Out of resource conditions may lead to discovery non completion(SCGCQ00568508 port of SCGCQ00435398 )  
  - PL: Phy Reordering will send a SAS Topology Change List Event with wrong ExpStatus(SCGCQ00568509 port of SCGCQ00551173 )  
  - Fury no longer links up to Maxim expander with phase 2 FW(SCGCQ00596630 port of SCGCQ00525026 )  
  - Whirlwind: Further IO path tweaks.(SCGCQ00609803 port of SCGCQ00583839 )  
  - PL: Target mode IO sends reply using wrong Hashed SAS Address(SCGCQ00712246 port of SCGCQ00703302 )  
  - 0x6004 fault on during controller reset test(SCGCQ00725165 port of SCGCQ00680866 )  
  - PL: Identify SSD needs to pend SATA Init when running(SCGCQ00725167 port of SCGCQ00702708 )  
  - Pli Control Request for IOP to Bypass FP disable on Selected Device Handle in Target Mode Based PL upon receipt of for non good response frame(SCGCQ00725182 port of SCGCQ00568651 )  
  - Remove event replay macro from mpi_temp.h file(SCGCQ00725196 port of SCGCQ00574398 )  
  - Fixed Problems with Power Condition VPD Page (0x8A  for Inquiry Command(SCGCQ00725233 port of SCGCQ00573940 )  
  - SAS Phy page 1 and 2 error counters don't perform properly(SCGCQ00725239 port of SCGCQ00588750 )  
  - Security freeze command fails with Check condition hardware error(SCGCQ00725241 port of SCGCQ00589464 )  
  - SATL: Incorrect Sense Info Obtained For a Request Sense Command During Read IO's(SCGCQ00725253 port of SCGCQ00604201 )  
  - PL: Add ConnectorName and EnclosureLevel fields to SAS Device Page 0(SCGCQ00725269 port of SCGCQ00464436 )  
  - Add ability to control ContinueAWT(SCGCQ00725279 port of SCGCQ00530872 )  
  - PL: Update Starfish register definition(SCGCQ00725305 port of SCGCQ00665118 )  
  - SATL: Indicate support for the ATA Device Server Password security protocol(SCGCQ00725310 port of SCGCQ00465302 )  
						
  - Print SES page data length and PL SES Diag page buffer size to ring buffer(SCGCQ00725311 port of SCGCQ00557625 )  
  - SATL is not returning ATA staus return descriptor correctly after processing ATA passthrough command(SCGCQ00725314 port of SCGCQ00659825 )  
  - PL: SCSI Read Command of Zero Transfer Length to SATA Returns Data(SCGCQ00725332 port of SCGCQ00672407 )  
  - SCSI Command is Not Failed with Expected Response When Reserved Fields Set as Non-Zero Value for SATA Disk Under Format(SCGCQ00725333 port of SCGCQ00679566 )  
  - PL: Firmware is not clearing RxDmaEng host parity interrupt(SCGCQ00725335 port of SCGCQ00680506 )  
  - After Controller Reset, Sense Data of REQUEST SENSE SCSI Command data is incorrect when SATA Drive is in Stand By Mode(SCGCQ00725341 port of SCGCQ00605087 )  
  - Allocation Length for REPORT LUNS SCSI Command is not Handled Properly for SATA Drive(SCGCQ00725367 port of SCGCQ00659829 )  
  - PL: Fix a few issues found by code analysis tool(SCGCQ00781307 port of SCGCQ00729588 )  
  - PL: Use an interrupt mask instead of multiple interrupts(SCGCQ00781308 port of SCGCQ00730675 )  
  - PL: SR-IOV IOs can trigger fault 0x2667 when FastPath is disabled to a drive in firmware(SCGCQ00781309 port of SCGCQ00676043 )  
  - SATA Init Problem Causing 0x6230 Controller Fault(SCGCQ00781311 port of SCGCQ00683795 )  
  - With VALID bit set INFORMATION field in Sense data is not populated for WRITE SAME(16  command(SCGCQ00781312 port of SCGCQ00684852 )  
  - WRITE SAME(10  command with UNMAP bit set in CDB doesnt behave as expected(SCGCQ00781313 port of SCGCQ00685000 )  
  - With VALID bit set INFORMATION field in Sense data is not populated for WRITE LONG(16  SCSI Command(SCGCQ00781322 port of SCGCQ00705308 )  
  - READ CAPACITY(10  SCSI command to a SATA drive returns unexpected data(SCGCQ00781331 port of SCGCQ00707233 )  
  - PL Fault 0x6003 While Running Heavy IO and Injecting Expander Resets on Alternating SAS Domains(SCGCQ00781345 port of SCGCQ00715211 )  
  - Fix Task Management coding error(SCGCQ00781364 port of SCGCQ00729603 )  
  - PL: Diagnostic CLI task management code has unreachable code(SCGCQ00781372 port of SCGCQ00731572 )  
  - PL: Remove legacy phy interrupts that don't exist anymore.(SCGCQ00793923 port of SCGCQ00735006 )  
  - PL: Enclosure management code doesn't check return value(SCGCQ00793928 port of SCGCQ00749722 )  
  - PL: SAS Device Page 0 read of valid devices returns error incorrectly(SCGCQ00793936 port of SCGCQ00764920 )  
  - PL: In Topology Change Event PhyStatus is not reported as Target Device missing(0x2  upon HDD removal(SCGCQ00816417 port of SCGCQ00777858 )  
  - PL: Enclosure Management SES Diag Page 2 does not check for Generation Code changes(SCGCQ00816419 port of SCGCQ00769393 )  
  - PL: TUR to a SATA command may not return correct ASC/ASCQ(SCGCQ00816421 port of SCGCQ00785787 )  
  - Fix compilation options(SCGCQ00816426 port of SCGCQ00788656 )  
  - Tiger WW: Make changes to support SED attached expanders(SCGCQ00837784 port of  SCGCQ00800429)  
  - Fixed the false return of "FRAME_ALLOCATE_FAILED" in PL(SCGCQ00848152 port of SCGCQ00836391 )  
  - (PL  0x5805 Fault during IO + Task Management test(SCGCQ00860390 port of SCGCQ00433677 )  
  - Unknown PL log information is observed by Host driver while testing SAS link down/up by disabling SAS phy of Controller(SCGCQ00894190 port of SCGCQ00868730 )  
  - PL: SAS Wide Max Queue depth not error checking correctly(SCGCQ00900645 port of SCGCQ00898573 )  
  - PL: SATL Translation of SCSI Write Buffer Modes 5 and 7 Incorrectly Sets FWFlags_NonAuto bit in HW Context(SCGCQ00917170 port of SCGCQ00897934 )  
  - Port Status Yellow LED GPIO not working(SCGCQ00917802 port of SCGCQ00907921 )  
  - PL: Manufacturing Page 30 DeQueueModes Setting in NVDATA is not Honored by Firmware(SCGCQ01004885 port ofSCGCQ00915975  )  
  - PL: Add extra prints to track when RxCtxMgr fails to stop(SCGCQ01004891 port of SCGCQ00949949 )  
  - PL: Initiator/Target moved can generate two Target Add Events(SCGCQ01005021 port of SCGCQ00934337 )  
  - PL: I/O timeout while running both auto and non-auto I/Os.(SCGCQ01025036 port of SCGCQ01022368 )  
  - FIS port handling of TRIM command with data length spanning multiple unmap descriptors(SCGCQ01073664 port of SCGCQ01051184 )  
  - SATA Only: Unsupported Log Sense commands fail with incorrect additional sense(SCGCQ01082896 port of SCGCQ01079905 )  
  - PL: Enhance PLI_CTRL_REQ_GET_SATA_HINT_INFO to also provide information of an active SATA Hinting discovery at a given time(SCGCQ01092177 port of SCGCQ01052367 )  
  - Unable to un-register a device because of outstanding Task Set Full MID(SCGCQ01109232 port of SCGCQ01076294 )  
  - SATA only: SANITIZE Command is Not Failed With Expected Sense Data for Service Action EXIT FAILURE MODE(SCGCQ01118557 port of SCGCQ01115136 )  
  - PL: 0x26B5 fault while running destructive domain test(SCGCQ01127836 port of SCGCQ01113264 )  
  - PL: Config page write current to Manufacturing Page 5 prior to Port Enable causes 0x4f01 fault(SCGCQ01150499 port of SCGCQ01149677 )  
  - PL: Fault 00005814 During IO + Cable Pull/Push(SCGCQ01177796 port of SCGCQ01168280 )  
  - ECC Error spike observed during Cache Restore when read eye training failed.(SCGCQ01198956 port of SCGCQ01124194 )  
  - PL SATA Only: outstanding SATA passthorugh IO can cause target reset from timer callback check if sata Initialization not done yet(SCGCQ01208721 port of SCGCQ01172334 )  
  - Fix coverity issues #15381(SCGCQ01236450 port of SCGCQ01211556 )  
  - SATA only : On EPC feature supported SATA drives, timers are still disabled even after setting the timers using Mode Select command(SCGCQ01276457 port of SCGCQ01263497 )  
  - IOP FW might observe I2C bus fault due to PL FW releasing I2C bus with active transaction.(SCGCQ01282482 port of SCGCQ01278309 )  
  - Ventura: Global IO activity LED may always stay ON in a NVMe VPP backplane server(SCGCQ01287732 port of SCGCQ01284596 )  
  - Adjust data structures for 8GB offload and restore operations(SCGCQ01288615 port of SCGCQ01279638 )  
  - (SATA Only  Fault 4203 while running SCSI unmap and TM to a SATA drive.(SCGCQ01294459 port of SCGCQ01287926 )  
  - Disable PUIS(Power up in standby  feature support(SCGCQ01305332 port of SCGCQ01304887 )  
  - Implemented handling for firmware upgrade/downgrade incompatible firmware and profile(SCGCQ01308534 port of SCGCQ01276905 )  
  - MR 7.2_Beta_NVMe Polaris LED is staying on(SCGCQ01317865 port of SCGCQ01312938 )  
  - Support for 128 drive enclosure(SCGCQ01318495 port of SCGCQ00920037 )  
  - RDM in Use-RDm Error & crashed into Montask during boot(SCGCQ01322145 port of  SCGCQ01147739)  
  - Port_Not_Required  port of  ) Chassis slot valid bit is not set into Enclosure Page 0 (SCGCQ01326055 port of SCGCQ01323680 ) 
  - Controller hang with FDE Drive (Micron 510DC(SCGCQ01326925 port of  SCGCQ01304133)  
  - PD Lost observed, after system graceful reboot or Controller OCR(SCGCQ01327295 port of SCGCQ01314168 )  
  - Data loss during cache offload power cycle test(SCGCQ01329142 port of  SCGCQ01286491)  
  - H840 montask while running AC cycle test during the 'cache offload testing'. Controller break into montask with Error Data Abort exeption.(SCGCQ01330207 port of SCGCQ01320912 )  
  - FW entered Exception mon_task while importing foreign PDs in loop.(SCGCQ01331535 port of SCGCQ01330764 )  
  - To close the window during which ONFI is not armed even when the data is dirty(SCGCQ01335210 port of SCGCQ01332552 )  
  - Marlin B0: backend PCIe: EC6D fault on link glitch(SCGCQ01337660 port of SCGCQ01336021 )  
  - Montask after data abort exception handler was called(SCGCQ01339605 port of SCGCQ01335905 )  
  - PA1: fw hit PL D10D while format partition(SCGCQ01346495 port of SCGCQ01333872 )  
  - Storcli response delayed up to 30sec when IO and CC running on LB+(SCGCQ01346753 port of SCGCQ01334602 )  
  - Active  port of  ) Incorrect TFM VPD data (SCGCQ01350076 port of SCGCQ01337835 )
  - controller wil not boot up after downloading the corrupted images ( app.rom, SBR, BTBL .. etc  because of CRC mismatch.(SCGCQ01370414 port of SCGCQ01330952 )  
  - Ventura: Slot LED status update operation may fail on 8i based HBAs(SCGCQ01373072 port of SCGCQ01372983 )  
  - Initiate Ocr after FW raises assert(SCGCQ01376506 port of SCGCQ01375574 )  
  - MR 7.2 NVMe : iMR Reconstruction is very slow(SCGCQ01382897 port of SCGCQ01330296 )  
  - If an INVALID applicationMsgTag id received, then failed the command with MFI_OOB_STATUS_INVALID_CMD using command id MAX_OOB_COMMANDS.(SCGCQ01383869 port of SCGCQ01337332 )  
  - pl: backend PCIe: EC79 fault(SCGCQ01389704 port of SCGCQ01367013 )  
  - Cisco - CSCvf25360 - STorCLI firmware log retrieval returns junk characters(SCGCQ01403301 port of SCGCQ01395855 )  
  - Interrupting Offload will Lead to Next offload cycle to fail(SCGCQ01404399 port of SCGCQ01399701 )  
  - Exception Handler Return address 0x01362c7d when boot up(SCGCQ01405520 port of SCGCQ01404373 )  
  - Enclosure redundant path show as not present and extra entry of enclosure is seen(SCGCQ01407464 port of SCGCQ01289603 )  
  - MR 7.4 - Hitting DC after OCR on 240 EPDs(SCGCQ01439279 port of SCGCQ01412665 )  
  - 9460-16i disappears from F1 setup after encrypting SED(SCGCQ01450194 port of SCGCQ01326871 )  
  - MR 7.4 - Hitting DC after OCR on 240 EPDs(SCGCQ01454603 port of SCGCQ01412665 )  
  - Ventura: FW may fault with 265D when attached to OEM NVMe backplane(SCGCQ01461873 port of  SCGCQ01385700)  
  - (VSES  SES INQUIRY commands and storcli commands hang while getting adapter information(SCGCQ01463865 port of SCGCQ01458388 )  
  - Flashed based 256 byte VPD programming support(SCGCQ01474040 port of SCGCQ01330751 )  
  - Ventura B0: Fault 0x510B while doing reboot test along with IOs & TMs(SCGCQ01487266 port of SCGCQ01440764 )  
  - [17B] Bugzila 120384 - [MFG] Purley Cosmo Raid card 530-8i loss during MQT1&2 Test(SCGCQ01511223 port of SCGCQ01504243 )  
  - Relaxed ordering Enhancement(SCGCQ00136149 port of  SCGCQ00131448)  
  - Data Errors seen with PL_LOGINFO_CODE_BT1680 on a SAS drive(SCGCQ00137250 port of SCGCQ00136641 )  
  - Pass Man page 8 SEP DevIndex in SAS Devicepage0 Slot field(SCGCQ00138852 port of SCGCQ00136626 )  
  - PL: PhyStatus Reason Code 0x2 not returned for a removed device(SCGCQ00140407 port of SCGCQ00137491 )  
  - Expander goes missing during Expander phy reset testing(SCGCQ00149146 port of SCGCQ00146846 )  
  - Obtaining proper value of Standby condition timer from Power condition mode page (page 0x1a  for a mode select command.(SCGCQ00150912 port of SCGCQ00144748 )  
  - Allow Config Write Current of SAS IO Unit Page 1 after PortEnable(SCGCQ00154828 port of SCGCQ00142923 )  
  - pl: SATL: Better handling of invalid signature FIS(SCGCQ00154930 port of SCGCQ00148569 )  
  - pl: SATL: need improvement to invalid initial FIS detection - continuation of SCGCQ00148569(SCGCQ00154931 port of SCGCQ00152050 )  
  - Convert MultiPathEnabled bit in PL_INFO_FLAGS to a reserved bit.(SCGCQ00155113 port of SCGCQ00151410 )  
  - PL: Discovery Error MPI2_EVENT_SAS_DISC_DS_MULTI_PORT_DOMAIN(SCGCQ00162081 port of SCGCQ00151755 )  
  - (PL-Only  Debug text strings are out of sync with the order of data(SCGCQ00162962 port of SCGCQ00152549 )  
  - [DISABLED]SAS pwr mgmt: If wakeup fails, next PM transition will hang(SCGCQ00168963 port of SCGCQ00153629 )  
  - Reserved value in DATAPRES field should cause response to be discarded(SCGCQ00169478 port of SCGCQ00164392 )  
  - Virtualization: Fault 7D70 with port virtualization enabled firmware.(SCGCQ00172536 port of SCGCQ00149660 )  
  - PL: Set the DA SEP as the managing SEP device for a OEM specific enclosure(SCGCQ00181069 port of SCGCQ00084007 )  
  - Fault 1901 running cable breaker with SATA drivers(SCGCQ00188489 port of SCGCQ00177110 )  
  - Workaround for failing to catch EEDP errors(SCGCQ00188871 port of SCGCQ00172683 )  
  - TM requests for SRST on SATA fails(SCGCQ00190438 port of SCGCQ00184968 )  
  - SAS Device Page 0 DeviceName field may be incorrect(SCGCQ00192676 port of SCGCQ00176761 )  
  - port enable completing before all drives discovered(SCGCQ00192711 port of SCGCQ00174426 )  
  - PL: Bad status frame sent (target mode(SCGCQ00194570 port of SCGCQ00184430 )  
  - Unexpected 7C41 fault on some receive path fatal errors in target mode(SCGCQ00194571 port of SCGCQ00180302 )  
  - Fix for controller sending HOLD after SATA device R_ERR of host to device FIS(SCGCQ00194748 port of SCGCQ00168243 )  
  - Observed Faultcode 0x265D(SCGCQ00209574 port of SCGCQ00194816 )  
  - WriteSame(16  translation to SCT Write Same always fails with timeout(SCGCQ00220866 port of SCGCQ00205567 )  
  - Task aborts due to I/O time out(SCGCQ00237407 port of  SCGCQ00194042)  
  - Improve STP connection timing behavior with idle connections(SCGCQ00250302 port of SCGCQ00219929 )  
  - PL: SMP Passthrough of Discover List may time out(SCGCQ00279510 port of SCGCQ00237373 )  
  - pl: TM: an Abort Task may time out with an Abort Task already outstanding at the device(SCGCQ00317273 port of SCGCQ00286353 )  
  - SATA: Link power management requests may fail after device initiated wakeup(SCGCQ00320015 port of SCGCQ00198601 )  
  - CONNECTION RATE value mismatch between incoming OAF and outgoing OAF(SCGCQ00335432 port of SCGCQ00242856 )  
  - Fixed a Case of Bad Coding Practice in Task Management Code(SCGCQ00408968 port of SCGCQ00334159  )  
  - Fixed Defect Introduced to Discovery Initialization Code(SCGCQ00433263 port of SCGCQ00349070 )  
  - Add comment to BT 798 WA header that WA isn't needed as SataOneKTimer functionality was completely removed in HW on B0(SCGCQ00434170 port of SCGCQ00321488 )  
  - Hits data tlb exception during SATL handling for UNMAP command(SCGCQ00438019 port of SCGCQ00357332 )  
  - SAS2 IT - Phase 15 – When SATA Drive is Moved to LU_Control from Stand-By, ASC/ASCQ is Incorrect for REQUEST SENSE(SCGCQ00445308 port of SCGCQ00337315 )  
  - PL: report AttachedPhyInfo data in SAS Expander Page 1(SCGCQ00459939 port of SCGCQ00356264 )  
  - SAS2 IT - Phase 15 – Allocation Length for REQUEST SENSE SCSI Command is not Handled Properly during SATA Drive Format(SCGCQ00462111 port of SCGCQ00334543 )  
  - Fault 0x6820 with IO+TM testing(SCGCQ00463267 port of SCGCQ00357910 )  
  - PL: Update starfish register header to reflect received TTIU(SCGCQ00463401 port of SCGCQ00356504 )  
  - Target Status Send request fails on retry(SCGCQ00472084 port of SCGCQ00338581 )  
  - Don't fail TMs to missing devices if the TM was issued with the DO NOT SEND TASK IU flag set.(SCGCQ00472117 port of SCGCQ00298825 )  
  - Fault 0x584B doing IO with cable pull/glitching(SCGCQ00472420 port of SCGCQ00390565 )  
  - (PL  0x58B4 fault: SAS PLL not becoming ready within 1 millisecond(SCGCQ00473994 port of SCGCQ00382525 )  
  - PL: SATL- SCSI Write Buffer command failure for modes 0x5 and 0x7(SCGCQ00494811 port of SCGCQ00400553 )  
  - File system creation on a SATA SSD drive failed in Linux.(SCGCQ00503260 port of SCGCQ00453641 )  
  - Fault d074 seen while running IOs on multiple SAS and SATA drives(SCGCQ00503701 port of SCGCQ00382251 )  
  - PL Fault d073 seen(SCGCQ00518532 port of SCGCQ00475648 )  
  - Add FPE Exception Q dumps to the pl dbg all dump(SCGCQ00529280 port of SCGCQ00386608 )  
  - Security freeze SATA devices at init time(SCGCQ00553449 port of SCGCQ00315229 )  
  - PL: SAT3 compliance - Implement translation of SCSI Sanitize command.(SCGCQ00553450 port of SCGCQ00357129 )  
  - Cable Management: Allow seeprom retry up to the time allowed by the spec(SCGCQ00555922 port of SCGCQ00407184 )  
  - Fixed Format of Timestamp Debug Print(SCGCQ00556329 port of SCGCQ00408378 )  
  - Fixed Bug in PL Initialization That Gave Priority DMA De-Queuing to Wrong DMA Group(SCGCQ00564103 port of SCGCQ00443879 )  
  - PL cable management: If an user plugs in an optical cable first, the port would be stuck in optical mode.(SCGCQ00565393 port of SCGCQ00467248 )  
  - Check in target error injection code(SCGCQ00565506 port of SCGCQ00393701 )  
  - Fixed Issue with SATA Translation of Security Protocol Out(SCGCQ00566110 port of SCGCQ00447912 )  
  - cli commands iop fpe maxex & maxev value do not allow reseting to the max SOD setting(SCGCQ00566121 port of SCGCQ00457383 )  
  - pl tm rsc does not show the default help message because the default value is incorrect(SCGCQ00566128 port of SCGCQ00457398 )  
  - pl pm memory needs it's parameter to be changed from memoptions to memtype(SCGCQ00566130 port of SCGCQ00457404 )  
  - cli command - pl sfw (Write Starfish register  does not use a base adderess of the Starfish Register(SCGCQ00566150 port of SCGCQ00465339 )  
  - Invader C0: 0x6B02 Fault while putting a PM capable SATA drive to partial or slumber mode(SCGCQ00566152 port of SCGCQ00465563 )  
  - (PL  Implement work around for BT [cobra ]1485.(SCGCQ00566165 port of SCGCQ00481655 )  
  - Fixed Problem with Mid Tracker Debug Code(SCGCQ00566171 port of SCGCQ00484802 )  
  - PL: TM timeout during enclosure pull while running heavy IO(SCGCQ00566173 port of SCGCQ00488106 )  
  - PL:Ensure synchronization when processor writing to memory and then a hardware core for SATL(SCGCQ00566180 port of SCGCQ00493424 )  
  - SATA FDE drive discovering as a regular SATA drive(SCGCQ00566183 port of SCGCQ00501329 )  
  - Check iopiMemoryMove(  Return Status - SMP Start(SCGCQ00566249 port of SCGCQ00477833 )  
  - Check iopiMemoryMove(  Return Status - Trace Buffer Manager(SCGCQ00566251 port of SCGCQ00477835 )  
  - Check iopiMemoryMove(  Return Status - Virtual Expander Manager(SCGCQ00566253 port of SCGCQ00477837 )  
  - Return the phy identifier for more SMP functions(SCGCQ00566263 port of SCGCQ00496987 )  
  - PL: Flush Writes and MemorySyncs in Control Queue and TxFM Cleanup to Ensure Robustness.(SCGCQ00566268 port of SCGCQ00518716 )  
  - PL: Porting firmware transmitter training code(SCGCQ00568426 port of SCGCQ00504071 )  
  - Force Full Discovery does not trigger rediscovery of an expander when the initial expander discovery fails(SCGCQ00568483 port of SCGCQ00358034 )  
  - FP IO's and FW IO's timing out on SATA disks(SCGCQ00596632 port of SCGCQ00563019 )  
  - Whirlwind: Set and clear FPE flags correctly for NVMe drives for TM housekeeping purposes(SCGCQ00649844 port of SCGCQ00640245 )  
  - PL: Identify SSD for SATA devices to use SATA Initialization(SCGCQ00725176 port of SCGCQ00704715 )  
  - PL: IO Stopping on SATA drives during destructive domain test(SCGCQ00725231 port of SCGCQ00563922 )  
  - D025 fault running non-FPE I/O to SATA disk with outstanding FPE I/Os to SAS disk(SCGCQ00725254 port of SCGCQ00604668 )  
  - Negotiated Physical Link Rate in SAS IO Unit Page 0 may not be correct after pulling a cable(SCGCQ00725264 port of  SCGCQ00692836)  
  - PL: Physical port structure is allocated too large(SCGCQ00725359 port of SCGCQ00669712 )  
  - PL: Implement customer specific SAS topology restrictions(SCGCQ00741763 port of SCGCQ00697961 )  
  - Update Attribution Language - Copyright, Trademark, Confidentiality to Avago(SCGCQ00758949 port of SCGCQ00729467 )  
  - Controller firmware returns unexpected SCSI response when NACA bit is set to 1 for unmap and security protocol in/out commands(SCGCQ00781321 port of SCGCQ00704291 )  
  - PL: Firmware could be accessing out-of-bound array elements handling SGPIO bays(SCGCQ00781358 port of SCGCQ00728865 )  
  - Fix a coding error in clean up code.(SCGCQ00781366 port of SCGCQ00729630 )  
						
  - PL: A diagnostic command was using the wrong size for register prints(SCGCQ00781370 port of SCGCQ00730743 )  
  - PL: ATA Pass-through command could return incorrect sector count in the status return descriptor(SCGCQ00793917 port of SCGCQ00726441 )  
  - PL: I2C sent to Direct Attach SEP and SEP NAKs sends wrong IOCLogInfo(SCGCQ00793934 port of SCGCQ00757690 )  
  - PL: IO timeout could happen when I/Os are coming from multiple sources(SCGCQ00793942 port ofSCGCQ00785298  )  
  - PL: Remove unused bits in enclosure and phy structures(SCGCQ00793953 port of SCGCQ00762351 )  
  - 'pl sfw' UART/CLI diag command to write a starfish register was broken.(SCGCQ00816416 port of SCGCQ00802662 )  
  - PL: Disabling Fast Path can cause memory corruption at start of day(SCGCQ00816423 port of SCGCQ00783657 )  
  - Tiger WW: Use controller LMids as SED SMids(SCGCQ00839590 port of SCGCQ00804417 )  
  - Tiger WW: Support Message Unit Reset to reset the messaging unit(SCGCQ00840269 port of SCGCQ00815861 )  
  - Tiger WW: Update to official MPI SED initialization messages(SCGCQ00841599 port of SCGCQ00830343 )  
  - TLB Error due to an already freed MID trying an "OPEN frame" in the SasCore(SCGCQ00848145 port of SCGCQ00813626 )  
  - Invader C0: Performance drops with PL version 0.250.113.0 on 2 R0 volumes behind Cobra(SCGCQ00855687 port of SCGCQ00400569 )  
  - PL: Modifying drive LEDs to specific expander using MPI SEP Request fails(SCGCQ00884017 port ofSCGCQ00873288  )  
  - PL: Out of resource condition may cause IOs to be pended indefinately(SCGCQ00890975 port of SCGCQ00885544 )  
  - PL: The max speed of SATA drives is not limited to 3Gbps by SAS IO Unit Page 1(SCGCQ00894195 port of SCGCQ00553305 )  
  - PL: SAS SPL-2 Drive Spinup Problem(SCGCQ00895314 port of  SCGCQ00892697)  
  - Cutlass A1: 0xC002 fault while doing Cable breaking on I/T Switching(SCGCQ00907375 port of SCGCQ00904531 )  
  - Firmware breaks into megamon with DATA TLB(SCGCQ01098884 port of SCGCQ00797553 )  
  - Fix the coverity issue(SCGCQ01236334 port of SCGCQ01204801 )  
  - Fixed Coverity Issue #15363(SCGCQ01236437 port of SCGCQ01211489 )  
  - Ventura: Remove NVDATA option added to enable PCIe RefClk for backplanes with no backplane mgmt(SCGCQ01303192 port of SCGCQ01279556 )  
  - pl: NVMe: unexpected IO failures with firmware path read/write IOs to an NVMe SGL device(SCGCQ01326943 port of SCGCQ01321013 )  
  - Data corruption on R6 WB VD when there are medium errors on one PD(SCGCQ01328413 port of SCGCQ01314319 )  
  - Ventura: AltData select, RefClk Mux not setup for SGPIO initiator prior to init(SCGCQ01328967 port of SCGCQ01321764)  
  - Ventura/Marlin: backend PCIe: IO halt after a link glitch(SCGCQ01337661 port of SCGCQ01336859 )  
  - RMC and CPLD out of Sync in COL cases(SCGCQ01340361 port of  SCGCQ01338876)  
  - Process all failed lmid in PL_MptDirectIoFailedList for the device that is getting removed before final devIoWait Queue clean up.(SCGCQ01341787 port of SCGCQ01331911 )  
  - PL Fault 0000d074 when run IOMeter overnight R0 fastpath(SCGCQ01346368 port of SCGCQ01331410 )  
  - Port_Not_Required  port of  ) IOs to LD stops while upgrading/downgrading between MR7.1/MR7.2 (SCGCQ01356689 port of SCGCQ01349963 )
  - Firmware should block to downgrade MR 7.2 NVMe profile to MR 7.1 SAS/SATA profile(SCGCQ01358640 port of SCGCQ01357859 )  
  - NVMe-enabled firmware fails to host boot on a blank board(SCGCQ01358762 port of SCGCQ01358750 )  
  - MR firmware hanging while waiting for BIOS restart after COL with power glitch(SCGCQ01365179 port of SCGCQ01291098 )  
  - Fix the smp ready set during device recovery which cause mid get re-used and later on cause pl fault(SCGCQ01384045 port of SCGCQ01338784 )  
  -  Active  port of  ) LB: 4 bytes PD (SA(S address displayed on drive removal/insertion events.(SCGCQ01384430 port of SCGCQ01346338 )
  - iMR driver is not initialized on certain OEM servers.(SCGCQ01397724 port of SCGCQ01375710 )  
  - When there's check condition FW doesn't return proper status and extended status(SCGCQ01401405 port of SCGCQ01396614 )  
  - Interrupting Offload will Lead to Next offload cycle to fail(SCGCQ01403954 port of SCGCQ01399701 )  
  - Active  port of  ) Prevent Improper Flash from I(S(SI (Supported (SBR/FW to nonport of  )I(S(SI (Supported (SBR/FW when Board has I(S(SI Chip (SCGCQ01421154 port of SCGCQ01410666 ) 
  - 9460-16i disappears from F1 setup after encrypting SED(SCGCQ01430654 port of  SCGCQ01326871)  
  - Ventura: Add support for OEM specific NVMe backplane detection and slot LED control(SCGCQ01460731 port of SCGCQ01346574 )  
  - Ventura MR - MR 7.4 not discovering NVMe devices(SCGCQ01462088 port of SCGCQ01453903 )  
  - Active  port of  ) When PFA drive is attached, it does not show predictive failure is detected. (SCGCQ01466076 port of SCGCQ01420232 )
  - Drives in Enclosure spin up values for OEM board is not initialized correctly(SCGCQ01466079 port of SCGCQ01450221 )  
  - MPI SEP request to Slots with invalid SES Page 0A element index may not complete(SCGCQ01487259 port of SCGCQ01482937 )  
  - Create compile option to disable SPL 2 power control(SCGCQ01499175 port of SCGCQ01468141 )  
  - pl: SATL: running large read/write IO to emulated ATAPI target fails with miscompare(SCGCQ00138313 port of  SCGCQ00135825)  
  - PL: PhyStatus Reason Code 0x2 not returned for a removed device(SCGCQ00151679 port of SCGCQ00137491 )  
  - Invalid Command Sequence following Link Reset(SCGCQ00153300 port of SCGCQ00145634 )  
  - Wrong sense format returned when media error is hit on sata drive with greater than 2TB size for VERIFY16 command(SCGCQ00154636 port of SCGCQ00138644 )  
  - Change how discovery handles spinup hold for sata devices(SCGCQ00156017 port of SCGCQ00142955 )  
  - SAS IO Unit Page 8 shows SAS link power management support when unsupported(SCGCQ00169037 port of SCGCQ00163175 )  
  - ModeSense request for Informational Exceptions Page may return zero in MRIE field.(SCGCQ00169459 port of SCGCQ00162847 )  
  - Modification to workaround for failing to catch EEDP errors(SCGCQ00188873 port of SCGCQ00179031 )  
  - INVALID_STATE reply to SCSI IO Unit Control request to remove a device.(SCGCQ00193403 port of SCGCQ00176387 )  
  - 5841 or 4101 fault on cable pull during IO(SCGCQ00232101 port of  SCGCQ00215388)  
  - Security protocol out translation for SAT specific protocol set password/unlock doesn't translate correctly(SCGCQ00237544 port of SCGCQ00227351 )  
  - Remove IOs from a Task Management's abort list if they are completed normally or with error.(SCGCQ00250733 port of SCGCQ00094580 )  
  - PL: SAS Gen-2 Open Reject (No Dest  Tracking(SCGCQ00258361 port of SCGCQ00247227 )  
  - Out of sync Phy cycling leads to an invalid expander details linked list and subsequent Discovery errors(SCGCQ00278342 port of SCGCQ00242703 )  
  - Write same command to a SATA drive that doesn't support SCT write same may write wrong region(SCGCQ00281620 port of SCGCQ00230159 )  
  - Fix handling of SATA drives which don't respond after being reset(SCGCQ00286168 port of SCGCQ00230606 )  
  - SAS2 IT - Phase 14 – Allocation Length for SCSI LOG SENSE Command is not Handled Properly(SCGCQ00315703 port of SCGCQ00283695 )  
  - Task management request with Retransmit bit set may time out in target mode(SCGCQ00317275 port of SCGCQ00294621 )  
  - pl: SATL: Nonzero reserved field during Log Sense (Informational Exceptions  translation(SCGCQ00320751 port of SCGCQ00285005 )  
  - Invader B0: Fault 0xD10E during Destructive Domain test validation.(SCGCQ00411358 port of SCGCQ00343989 )  
  - SAS2 IT - Phase 15 – Read Buffer SCSI Command is Not Failed with CC When ALLOCATION LENGTH is set to Value Other than 512(SCGCQ00433368 port of SCGCQ00329472 )  
  - PL: Do not send up additional SAS Topology Change List Events for phys with a Function Result of Phy Vacant(SCGCQ00437102 port of SCGCQ00307602  )  
  - PL: Improve SATA Non Auto IO management with Fast Path enabled or disabled.(SCGCQ00455696 port of SCGCQ00362952 )  
  - Fixed Problems with Parity Checking Workaround Which Caused 4A00 Fault(SCGCQ00458991 port of SCGCQ00356050 )  
  - Invader: Fixed Transport Layer Retries (TLR  Issue Where a Command Can Sometimes Be Incorrectly Retried(SCGCQ00461980 port of SCGCQ00368444 )  
  - Fault 0x4851 seen when running a setup talking to a target mode controller(SCGCQ00463094 port of SCGCQ00383728 )  
  - (GEMINI  HB Command getting lost(SCGCQ00463360 port of SCGCQ00257597 )  
  - PL Fault 0x620F when inquiry issued to Sata device while a background test is active.(SCGCQ00469663 port of SCGCQ00342770 )  
  - Invader B0: Enable Halt on FPE Requestor/Completor Parity Error(SCGCQ00469913 port of SCGCQ00361819 )  
  - Invader: Updated Runtime Workaround Matrix for C0 Chip Revision(SCGCQ00472981 port of SCGCQ00356255 )  
  - fault d073 with timeouts while running straight IOs(SCGCQ00523634 port of SCGCQ00364113 )  
  - Fixed Issue Caused by Lack of Hardware Cleanup in Rx Context Manager(SCGCQ00550165 port of  SCGCQ00406905)  
  - Cable management: Support I2C mux on the production boards(SCGCQ00553535 port of SCGCQ00392397 )  
  - Fixed 6001 Fault Caused by Defects in Task Management(SCGCQ00562743 port of SCGCQ00421304 )  
  - HwLinkRate in sas phy 0 shows 6G as max link rate and 1.5G as min link rate(SCGCQ00564690 port of SCGCQ00422172 )  
  - Fixed Context Area for SATA Translation of SCSI SANITIZE Command(SCGCQ00566096 port of SCGCQ00423990 )  
  - Controller watch dog timed-out(SCGCQ00566104 port of SCGCQ00440696 )  
  - pl stats resets description needs to indicate that the FPE counters are reset as well.(SCGCQ00566126 port of SCGCQ00457391 )  
  - cli commands pwmview, ps and pmcntr need their descriptions to be fixed(SCGCQ00566129 port of SCGCQ00457401 )  
  - Invader: Initiator getting Open Reject (NoDest  in valid topology(SCGCQ00566157 port of SCGCQ00470884 )  
  - PL Host Based Discovery: Task Management delay in some cases(SCGCQ00566170 port of SCGCQ00484722 )  
  - Check iopiMemoryMove(  Return Status - STP Passthrough PIO Data Received(SCGCQ00566247 port of SCGCQ00477830 )  
  - PL: Add macros to pause and unpause FPE requestor and completor(SCGCQ00566256 port of SCGCQ00481594 )  
  - VALID Bit is Always Set in Sense Data for failing REASSIGN BLOCKS SCSI Command(SCGCQ00568487 port of SCGCQ00456224 )  
  - (Sata Only  Multiple 'Write Verify' SCSI commands with zero data length leads to f/w fault.(SCGCQ00725204 port of SCGCQ00501322 )  
  - SMP Response Received from Previously Removed Expander Causes Callback Stack Underflow(SCGCQ00725230 port of SCGCQ00563292 )  
  - PL: Improve the handling in PL FW while checking the Requestor or Completor’s idle state to increase the FPE performance.(SCGCQ00725280 port of SCGCQ00549891 )  
  - PL: Update EDFBMaxGroupUnload default value to 4 and add debug features(SCGCQ00725281 port of SCGCQ00551447 )  
  - Change TM context TaskMid to TaskIUorSMPMid(SCGCQ00781303 port of SCGCQ00723452 )  
  - PL: Remove unused local pointers(SCGCQ00781305 port of SCGCQ00728910 )  
  - PL: CDB checking was not done properly for devices under format or self-test(SCGCQ00781326 port of SCGCQ00706052 )  
  - Nulling SAS analog front end offsets(SCGCQ00781384 port of SCGCQ00665144 )  
  - Tiger: Implement MPI reply function pointer callback(SCGCQ00840063 port of SCGCQ00816056 )  
  - Fix provided in PL Enclosure Management to check for the upper bounds of Slot Number(SCGCQ00851643 port of SCGCQ00825045 )  
  - PL: Supported VPD pages being sent out of order for SATA drives with Power Condition Page Support(SCGCQ00874474 port of SCGCQ00865796 )  
  - Invader C0: PL Fault 0x5814 while handling Task Management during IO Timeout(SCGCQ00894187 port of SCGCQ00842366 )  
  - sg_unmap command to a SATA drive was not working correctly for the Last Block.(SCGCQ00894194 port of SCGCQ00869961 )  
  - To properly handle the case of configfuring the specific server backplanes of type direct attached SEP and In-band SEP(SCGCQ01004549 port of SCGCQ00994396 )  
  - Data Miscompare found during recovery of CacheCade pinned windows across OCR/Reboot or discard of CacheCade pinned windows while CacheCade degrade flush in progress(SCGCQ01197025 port of SCGCQ01118285 )  
  - Assertion failure in ../../dm/mpt2/mptcmd.c at line 1418 during PD offline on R5 using DIF drives.(SCGCQ01198936 port of SCGCQ01152599 )  
  - IMR FW fails to support 32 configured good drives, during JBOD to good and array removal step.(SCGCQ01198937 port of SCGCQ01161841 )  
  - Coverity issue 15748 and 17765(SCGCQ01249617 port of SCGCQ01241568 )  
  - Implemented new firmware to support 240 PDs and VDs(SCGCQ01277488 port of SCGCQ01238071 )  
  - Active  port of  ) C(SCvd34454 C(SC.nuova,new,stallamr PL: 1MBIO support blocked as we are unable to enable or disable the feature(SCGCQ01292625 port of SCGCQ01287919 ) 
  - HW: DMA hang(SCGCQ01320682 port of SCGCQ01305741 )  
  - Port_Not_Required  port of  ) C(SET: Add handling for firmware upgrade/downgrade incompatible firmware and profile port of  )  (SCGCQ01276905 (SCGCQ01325289 port of  ) 
  - MR7.1 : BBU retentiontest doesnot start(SCGCQ01326931 port of SCGCQ01236513 )  
  - More latency observed during device discovery(SCGCQ01327290 port of SCGCQ01311662 )  
  - Ventura: Add TM IOCStatus to TM Logger(SCGCQ01338919 port of SCGCQ01336984 )  
  - IOMMU fault at address 0x80360000(SCGCQ01346993 port of SCGCQ01279547 )  
  - AVAGAO Option ROM hang was seen after 155 container update(SCGCQ01384638 port of SCGCQ01346450 )  
  -  Active  port of  ) CiscoLBP: Firmware asserted at dm/src/dm.c at line 1701: gDevInfo[pd].dmIoQ.waitQCount == 0 when remove drives to offline VDs(SCGCQ01385116 port of SCGCQ01352158 )
  - Cisco_HSW_Validation: FW should not allow the user to make JBOD when clear drive operation is in progress on the same drive.(SCGCQ01385626 port of SCGCQ01345363 )  
  - Making MCTP interrupt context code FIQ safe.(SCGCQ01391425 port of SCGCQ01387060 )  
  - MR7.1 -587: Flash write Failed with err code 5(SCGCQ01411024 port of SCGCQ01396383 )  
  - Parameter Page Reads fail during ONFI bringup.(SCGCQ01413785 port of SCGCQ01413557 )  
  - Ventura: Implement workaround for device attached to PCIe front end with IDT timer(SCGCQ01448014 port of SCGCQ01401585 )  
  - pl: port enable may fail to complete if an OEM backplane is attached(SCGCQ01464752 port of SCGCQ01455680 )  
  - (PL-Only  Write Verify commands fail to SATA drives when SGLOffset0 is not 0x18(SCGCQ00135589 port of SCGCQ00135587 )  
  - In some cases, the CK_COND bit from ATA passthrough message was ignored.(SCGCQ00168597 port of SCGCQ00159042 )  
  - Transfer count in I/O reply is not always accurate(SCGCQ00172689 port of SCGCQ00166078 )  
  - PL Library code is invalidly using a function parameter where it's not allowed to per the PLI spec(SCGCQ00247175 port of SCGCQ00204054 )  
  - PL: SMP Report Phy SATA failure(SCGCQ00552328 port of SCGCQ00399753 )  
  - (IOP  Ensure synchronization when processor writing to memory and then a hardware core for SMP(SCGCQ00566168 port of SCGCQ00484051 )  
  - Invader: Add Fault Code - Abort Task Missed Its IO with Pend Flag Set(SCGCQ00566201 port of SCGCQ00559156 )  
  - Check iopiMemoryMove(  Return Status - SATL Unmap, Write Same Commands(SCGCQ00566242 port of SCGCQ00476179 )  
  - NVDATA Option to Allow Force Dual Context On(SCGCQ00566265 port of SCGCQ00501686 )  
  - PL: Identify SSD code fails to test for IO start failure(SCGCQ00725168 port of SCGCQ00702716 )  
  - Report Luns Command fails with CheckCondition/Invalid Field in CDB when Allocation length set to Zero(SCGCQ00725240 port of SCGCQ00589463 )  
  - Unexpected IOCStatus in Error Reply when NAK is received by Fury in target mode(SCGCQ00725260 port of SCGCQ00662771 )  
  - WB volumes not getting imported on changing personality from raid to HBA(SCGCQ01198913 port of SCGCQ01135382 )  
  - CSET: FW Pkg: 360: Guest OS encountered error/no controller found while attempting to install windows driver - (SCGCQ01279806(SCGCQ01317686 port of  NA )  
  - ATA Passthrough MPT frame content has overwritten(SCGCQ01348118 port of SCGCQ01339127 )  
  - MR 7.3 PA4: Controller restart command hung during IO on VD's and Jbod's(SCGCQ01357445 port of SCGCQ01343745 )  
  - Flashed based 256 byte VPD programming support(SCGCQ01378115 port of SCGCQ01330751 )  
  - Replacing RAID Controller with Degraded VD Hangs System(SCGCQ01403745 port of SCGCQ01393703 )  
  - MR7.1: Shutdown command received from host" missed in tty log(SCGCQ01411329 port of SCGCQ01389941 )  
  - Flashed based 256 byte VPD programming support(SCGCQ01430628 port of SCGCQ01330751 )  
  - Spare filtering does not prevent NVMe PD from being used as spare for SAS/SATA array.(SCGCQ01478265 port of SCGCQ01441173 )  
  - MR7.3 & 7.4 With iMR Unconfigured NVMe drives become Unconfigured Bad When Converting Them to JBODs(SCGCQ01483142 port of SCGCQ01479017 )  
  - Global HDD LED may not indicate IO activity for NVMe or SAS drives(SCGCQ01496628 port of SCGCQ01489030 )  
  - Device Not added during power cycle test.(SCGCQ00173284 port of SCGCQ00164383 )  
  - SATL: Informational Exceptions log page read fails(SCGCQ00243225 port of SCGCQ00188519 )  
  - SAS2 IT - Phase 14 – Allocation Length for SCSI MODE SENSE Command is not Handled Properly(SCGCQ00315406 port of SCGCQ00285381 )  
  - Enhancement to Debug Information Provided by UART(SCGCQ00435510 port ofSCGCQ00335631  )  
  - SAT3 Compliance - Disabled Background Translation for ATA SCT Write Same(SCGCQ00553526 port of SCGCQ00357132 )  
  - Log Supercap Fault Assertion along with associated status bits during run-time(SCGCQ01282810 port of SCGCQ01011381 )  
  - Static analysis defects(SCGCQ01288653 port of SCGCQ00767988 )  
  - 0x6001 Fault due to a missing IO that went through the IO resubmit path(SCGCQ01369963 port of SCGCQ01330777 )  
  - Ventura: Implement workaround for device attached to PCIe front end with IDT timer(SCGCQ01425032 port of SCGCQ01401585 )  
  - Bugzila 112779 - [SAMSUNG PM863A SSD can not show the "Part Number"/ "FRU Number" information under XCC web w(SCGCQ01448010 port of SCGCQ01435624 )  
  - Host Based Discovery: NegotiatedLinkRate field of SAS IO Unit Page 0 and SAS PHY Page 0 not filled out(SCGCQ00566118 port of SCGCQ00456290 )  
  -  Port_Not_Required  port of  ) Dev defect: To checkport of  )in Intruder specific params page update changes.(SCGCQ01198968 port of  SCGCQ01155893)
  - Enable I2C polling for drive presence detection in VPP Type B backplanes with NVMe support.(SCGCQ01460733 port of SCGCQ01375330 )  
  - Spare filtering does not prevent NVMe PD from being used as spare for SAS/SATA array.(SCGCQ01466124 port of  SCGCQ01441173)  
  - Fast Path IO is not failed for LDBBM table entries(SCGCQ01466133 port of SCGCQ01452385 )  
  - Replace POM0 usage with SysDma(SCGCQ01448534 port of  SCGCQ01430023)  
  - Added NVME passthrough support for MR stack(SCGCQ01451159 port of SCGCQ01391416 )  
  - 930-16i Cannot Spinup HDD During System Power On(SCGCQ01472470 port of SCGCQ01470741 )  
  - MR 7.4 - PDs pull/push led to "Assertion failure in ../../cpu/arm/exceptions.c at line 938: 0"(SCGCQ01484822 port of SCGCQ01460017 )  
 
 
 EnhancementRequests:
-Gen3: SHELL Performance Monitor (SCGCQ00095392)
- Add support for new TxFM interrupts in Colt(SCGCQ00105521)
 -Manufacturing Config settings for End Device Frame Buffering(SCGCQ00123628)
 -TBM: Implement plTBMGetTraceDword(SCGCQ00127520)
 -Add basic support for new hardware block state timers in SAS core blocks(SCGCQ00127730)
 -Updates for SAS Core changes to Rx/TxBuffer alias addressing(SCGCQ00127731)
 -Gen3: TBM (SCGCQ00127747)
 -Add handlign for new TxFM interrupt(SCGCQ00129375 )
 -Modify mfg page 3 to incorporate back channel training.(SCGCQ00131013)
 -pl: Power condition support in SATL: Start/Stop Unit(SCGCQ00131188)
 -Allow Config Write Current of Manufacturing Page 5 after PortEnable(SCGCQ00131631)
 -TBM: Incorporate a FW header in the Extended Buffer for the parser(SCGCQ00132403)
 -PL: review usage of TxDmaStart Busy(SCGCQ00135548)
 -Gen3 PwrMgmt: Integrate individual power management components into chip(SCGCQ00136952)
 -Gen3 PwrMgmt: Add IOP support for PCIe Dynamic Power Allocation (DPA)(SCGCQ00136955)
 -Add 8 bits to MidTracker and use for FPE (or as needed)(SCGCQ00140772 )
 - FPE - instead of faulting on IOP Request Q full, error reply back IO with ISTATUS_NOT_HANDLED(SCGCQ00141509)
 -PL must start/stop timers for IOs if IOP is using Cuda Timing Wheel and PL starts IO directly to colt(SCGCQ00141735)
 -Update project to the Phase 7 MPI Header Files(SCGCQ00141743)
 -Invader: Incorporate Colt EDS 1.1 support for modified QM registers.(SCGCQ00141765)
 -Ensure RX DMA IO cleanup matches latest Colt EDS 1.1(SCGCQ00141768)
 -colt EDS 1.1 updates to colthw.h(SCGCQ00141814)
 -additional EDFB checks(SCGCQ00142947)
 -Add some FPGA workarounds currently needed to FPGA build(SCGCQ00142976 )
 -Update plClearTxCtxMgrDmaPassthruInt(U32 TransNum) for dual context(SCGCQ00143260)
 -FPE disabled on a device operation should also set the HW Device table bit that forces SASCore to route completions to Firmwa(SCGCQ00143919 )
 -Set up the SGL flags according to the MsgFlags so the sense data goes to the righ memory space.(SCGCQ00143985)
 -Gen3 Task Mgmt Debuggability & Testability Improvements (SCGCQ00144418 )
 -FPE: Disable/Mask all Cuda Interrupts before Cuda Int and Enable/Unmask them after(SCGCQ00144452)
 -convert pliDevHandleFind() to PL only function(SCGCQ00144456)
 -Invader: Update files to support dual context DmaTransmissionQs. (SCGCQ00144611)
 -Add support for LD state table in Cuda(SCGCQ00144627 )
 -Gen3 Task Mgmt: Check SATA IT_NEXUS RESET response to SRST(SCGCQ00145028)
 -FPE: Upgrade the FPE Init process to initailize Detroit memory more elegantly(SCGCQ00145070 )
 -FPE (SCGCQ00145411)
 -set PoolTxDMAs option to 0(SCGCQ00145649)
 -Investigate the remaining SATA cases where FWFlags_NonAuto is used to see if the SATA dev Table NonAuto is sufficient(SCGCQ00145753)
 -FPE (SCGCQ00146696 )
 -SATA: mark sata device fast path capable.(SCGCQ00147727)
 -For FPE Exception Queue(s), add mid valid type check capability(SCGCQ00147961)
 -Update PLI to allow passing of VF Request Q sizes(SCGCQ00148029)
 -Update iopiMemoryMove Function for Gen3(SCGCQ00148770) 
 -pl: Add an ATA command needed for ACS(SCGCQ00149006)
 -txdma cleanup changes from Colt EDS 1.21(SCGCQ00149016)
 -colt eds 1.21 dma Q cleanup changes(SCGCQ00149017)
 -TBM: Update pliFpeCheckpointOrTraceInterrupt with Trace Buffer interrupts handling(SCGCQ00149046)
 -Set Qmgr Debug reg bit 20 to 1 during Qmgr init(SCGCQ00149247 )
 -FPE: Add PLI contreq function to support "Route All To Exceptoin Queues" bit in FPE Control reg(SCGCQ00149686)
 -add PLI control request support for Vendor Specific case 1(SCGCQ00149688)
 -add PLI control request support for FPE Config 3 FpUseLdTableFlags bit(SCGCQ00149689)
 -update PLI Control request PLI_CTRL_REQ_OPERATION_FPE_SET_LD_TABLE_BASE to also set size of LD table(SCGCQ00149690)
 -pl: Allow sense data for ATAPI device to go to other address space than just pci(SCGCQ00150256)
 -FPE: Firmware changes for Detroit 1.2 EDS release(SCGCQ00150513)
 -SAT3 update: Use Download Microcode DMA if the device supports it(SCGCQ00151344)
 -SAS(SCGCQ00151863)
 -SAS(SCGCQ00153239)
 -FPE (SCGCQ00155475)
 -Set the lower two bits of the context address correctly when messing with non (SCGCQ00155499)
 -Gen3: Support FPE NVDATA changes(SCGCQ00155854)
 -EDFB: free DMA Group when expander structure is de(SCGCQ00155912)
 -pl: make sure TM and hw clean up code doesn't use mid 1(SCGCQ00156442 )
 -Add handling to various interrupts generated by the context non auto bit being set during task management.(SCGCQ00157017)
 -FPGA: FPE needs to flush mid state writes through PLB before posting IO to Cuda's IOP Start Queue from PL(SCGCQ00158620)
 -Remove 250ms delay at the end of TMs(SCGCQ00159959)
 -Change Trident FMU address macros to match correct hardware address decodes(SCGCQ00159978)
 -Add indication of FPE enabled/disabled to pl status UART command for each device(SCGCQ00160296)
 -Include debug strings in diag buffer(SCGCQ00161332)
 -Macro for setting device state table fpe flags(SCGCQ00161423 )
 -FPE: rework when/how FPE is enabled for SATA devices (SCGCQ00161435 )
 -FPE: implement start pending IO function for FPE devices(SCGCQ00161456)
 -FPE: add MID State table dump to the existing UART mid dump cmd(SCGCQ00161659)
 -FPE: add FPE dev state table dump to existing UART per device cmd(SCGCQ00161660)
 -Performance counters (SCGCQ00163008)
 -FPE: add some more debug to Requestor and Completor error/faults(SCGCQ00163734)
 -TBM: Add debug code for TBM errors(SCGCQ00164570)
 -PL Light: add pliLight equivalent for get mid state table info(SCGCQ00165286)
 -Remove #if PL_FEATURE_TM_ENHANCE_(ALL, MEDIUM, BASIC) from gen3 code(SCGCQ00166369)
 -plTaskMgmt.c cleanup(SCGCQ00166732)
 -FPE: remove Cuda timer if IO is timed by cuda and TM aborts it(SCGCQ00168251 )
 -FPE: changes to ioflags usages for reply destination and ignore context(SCGCQ00168410)
 -pl: FP IOs started by pl would print out the lba of the command(SCGCQ00168434)
 -FPE: Comments to WA for BT 762(SCGCQ00168742)
 -Update TM code to comply with new cuda pend list cleanup(SCGCQ00168994)
 -Update Outstanding Mids in SASCore HW cleanup for gen3. Remove RxFS nomenclature.(SCGCQ00169015)
 -Add API in Gen3 to manage power modes of Starfish SERDES phys.(SCGCQ00169389)
 -FPE: add support for exception FPESTATUS_FPE_MU_REQUEST(SCGCQ00169460))
 -Fail the sata io if the driver tries to send a large cdb(SCGCQ00169712)
 -FPE: TM abort list should be checked when handlign Cuda Timer Wheel timeouts(SCGCQ00169942)
 -FPE: further tweaks to the add/remove FPE timer functions(SCGCQ00169943 )
 -Turn on LL parity checking(SCGCQ00170270 )
 -Add print out of the Abort list for a TM when it causes a fault.(SCGCQ00170549)
 -Update TM Tracker functionality (SCGCQ00171097)
 -pl: update starfish registers to EDS 1.4(SCGCQ00172537)
 -HW WA (SCGCQ00172588)
 -Detroithw.h changes to support Detroit EDS 1.35(SCGCQ00173443)
 -Add PLI defnies for FPE Power Savings modes(SCGCQ00173648)
 -Report to host the offset of first EEDP error (SCGCQ00175700)
 -Firmware handling for non(SCGCQ00176261)
 -Update RxCtxMgr Cleanup to match new gen3 hardware functionality(SCGCQ00178840)
 -don't enable LINK_SIGNALLED_ERROR in rxFM and rxCtx(SCGCQ00179174)
 -HW WA (SCGCQ00179251)
 -Update DMA Transmission Queue cleanup to check 256 DMA groups(SCGCQ00179253)
 -Add #defines for access to dma engine registers.(SCGCQ00179629)
 -FPE: Investigate optimizing FPE invalid descriptor handling(SCGCQ00180215 )
 -Remove [SAS2Core] 1650(SCGCQ00180225)
 -Remove [SAS2Core] 766 (SCGCQ00180303)
 -PL: allow each phy to initialize its electrical parameters from the proper phy group(SCGCQ00181727)
 -Add initial support for R25 (B0) SASCore version(SCGCQ00184044 )
 -Update TxCtMgr NonAuto handling to match ColtEDS1.4(SCGCQ00184341)
 -Invader A0 bring up(SCGCQ00186022)
 -allow phy to link up at 6G(SCGCQ00186469)
 -Gen3: support SAS Notify Power Failure Expected (EPOW)(SCGCQ00186531)
- Check in the consolidate serdes values for all link rates(SCGCQ00186615)
- Update colt.h with new field value for hardware parameters 0(SCGCQ00186660)
 --FPE: Add PLI interface to allow IOP to write MSindex, VF_Id and SMID into Cuda's MST(SCGCQ00187301)
 -Update serdes values based on SE's recommendation(SCGCQ00188253)
 -Setup RxEEDP with a more reasonable time duration HW should wait before going into low power mode(SCGCQ00189198)
 -Increase the number of SGE's PL will print(SCGCQ00189211)
 -Need a PLI control request to get the SAS core version(SCGCQ00192893)
 -Adaptive Serdes settings(SCGCQ00194276)
 -EDFB: flag if non(SCGCQ00199495 )
- Add R27 SASCore recognition(SCGCQ00199520)
- Update TM to have a "marker" mid for the Colt(SCGCQ00199733 )
 -New serdes settings from SE(SCGCQ00200293 )
 -Add FW support for new B0 RxFM/RxCM"WrongDataDirection interrupts(SCGCQ00202861)
 -Put in a workaround from gen2 for a Close (Clear Affiliation) issue(SCGCQ00204226)
 -Check on handling RegAccErr interrupts(SCGCQ00205704)
 -Setup SSC down spreading based on SE's recommendation(SCGCQ00208582)
- implement new serdes settings(SCGCQ00209730)
- Invader Performance: Do not allocate FPE queue when disabled (SCGCQ00209915)
- PL: check in new serdes settings(SCGCQ00213218)
- Update SnC Method (08/16/2011 3:54 PM)(SCGCQ00213372 )
- FCS: FCS enable on Invader must be based on inbound phy on Cobra(SCGCQ00217065)
- Update TxDma SnC 8/22/2011 3:02 PM(SCGCQ00220010)
- Update SnC Method to restore power management values after a full reset(SCGCQ00221381 )
- Further performance related enhancements to printing/TBM code(SCGCQ00221673)
 -Invader A0: optimize prints to disable io printing when TBM is enabled(SCGCQ00222985)
 -Invader A0 PL FPE Start IO performance optimzation(SCGCQ00223252)
 -Invader A0: PL to FPE IO Performance optimizations Stage 2(SCGCQ00223517 )
 -Updates to new SnC Method from HW.(SCGCQ00224783)
 -Active cable support part one(SCGCQ00225179)
 -Add DCR reg info on SASConfig Reg Fault 7C53(SCGCQ00225800)
 -Active cable support part two(SCGCQ00226322)
 -Invader A0: FPE Io Path Optimization(SCGCQ00226323)
 -BT [invader]1055 Workaround changes(SCGCQ00228609)
 -Need a mechanism to enable ALF bit in PllcControl register (PLB Offset 0x10) (at least for direct attached drives)(SCGCQ00229311)
 -Update HostDifMemoryThreshold and CacheDifMemoryThreshold per hardware group's request(SCGCQ00229833)
 -Add a check for SMP frames in the Dual context reset algorithm(SCGCQ00231957)
 -Initialize Port Layer Settings such as ALF bit and Port Link Availability initial count from Man Page 17(SCGCQ00237340)
 -(SAS3 IR) Enhance Handling of Fast Path I/Os to Fast Path Disabled Devices to Prevent Unwanted Device Writes (SCGCQ00237718)
 -Investigate a method to have PL always turn FPE back on at the end of TM(SCGCQ00242895)
 -BT 1629 WA implemenation(SCGCQ00244096)
 -Change a variable name to reflect the usage of the variable better(SCGCQ00245503)
 -STP AlwaysActivated needs to be turned off for a device when doing non(SCGCQ00246290)
 -PL: update PL_SATA_DATA_BLK_RES to 0xF per SE's request(SCGCQ00247864)
 -Active cable management: Clear I2C retry counter once the cable is unplugged(SCGCQ00249923)
 -Initialize BcMaxSeg to the correct value(SCGCQ00254062)
 -A modified IT controller firmware build is needed in order to test Fastpath IO Timer functionality(SCGCQ00254775 )
 -Remove Link Multiplexing support(SCGCQ00258634)
- Define new bit fields in a starfish register(SCGCQ00259496 )
- Minor Definition Changes to Fast Path Engine for Forward Compatibility(SCGCQ00260013 )
 -Invader A0: (PL) Manage and restructure diagnostic command source code.(SCGCQ00261860 )
 -Disable BT1486 WA due to the heavy performance impact(SCGCQ00265982)
 -Starfish B0 changes (SCGCQ00266473 )
 -Support SGPIO Group ID slot enumeration for non(SCGCQ00271338)
 -PL: Update to the latest 1.1 serdes settings for Invader B0(SCGCQ00276158)
 -Invader B0: FPE New Feature Validation Test instrumentation(SCGCQ00279184)
 -Print out starfish label when dumping starfish registers (SCGCQ00281681)
 -Added Cable Management file to PL makefile(SCGCQ00284543)
 -Latest serdes settings for back channel training(SCGCQ00286360)
 -Help with connectivity for SATA drives(SCGCQ00296972)
 -Register setting to help with back channel training(SCGCQ00298482 )
 -PCIe interrupt (INTx, MSI/MSI(SCGCQ00308797)
 -Implemented Hardware Work Around: DMA Engine Asserting Invalid Rollover Interrupt(SCGCQ00313865)
 -Invader B0: Certain key customer specific status flags not getting set properly by hardware during exception handling.(SCGCQ00314499)
 -(IOA) Added firebird.h(SCGCQ00323012 )
 -Added a PLI Control Request Operation To Get Count of Known EDFB (DataBolt) Enabled Devices(SCGCQ00333765 )
 -[Dauntless]: Prevail HW header file(SCGCQ00337003)
 -NVMe Mode Sense and Mode Select translations(SCGCQ00338540)
 -(IOA) Add initialization for new functions in DV Firebird core(SCGCQ00343530)
 -Additional SCSI to NVMe translations(SCGCQ00345822)
 -Added support for nwe IO accelerator completion queue(SCGCQ00347555)
 -(IOA) Add Invader(SCGCQ00350778)
 -pl pci: Discovery and Device Manager(SCGCQ00352772)
 -(STANG) Implement PCE (stang) exception and completion queue interrupts(SCGCQ00362507)
 -Distribution of PCI space obtained from the host amongst PDB PIM windows.(SCGCQ00362905)
 -Backend PCIe device memory allocation (part 1)(SCGCQ00365971)
 -Backend PCIe device memory allocation (part 2)(SCGCQ00372536)
 -(PL(SCGCQ00377476)
 -Disable Invader workarounds that were fixed in Dauntless Colt core(SCGCQ00385300)
 -(IOP) Compile in security options on FPGA for DAUNTLESS(SCGCQ00386217)
 -More NVMe related changes(SCGCQ00390988)
 -FPE trace buffer prints for PCIe devices(SCGCQ00394555)
 -Update Silverhawk and Prevail PIM/POM settings to support Subtractive routing(SCGCQ00394770)
 -Backend PCIe: Allow de(SCGCQ00397609)
 -Additional diag console commands(SCGCQ00398216 )
 -Queue full handling for NVMe admin queue(SCGCQ00399212 )
 -Add PCIe Link config pages to read and configure PCIe link error and event counters(SCGCQ00400394)
 -FW Read/Write IO Path (SCGCQ00400467)
 -FW Read/Write IO Path (SCGCQ00400472 )
 -NVMe: Update NVMe non read write translations(SCGCQ00401386)
 -(IOA) Modify IOA Timer RAM initialization for FPGA(SCGCQ00402245 )
 -New debug information (SCGCQ00412145)
 -Add max payload workaround for Lecroy NVMe device emulator(SCGCQ00414595)
 -NVMe: Read/write IO breakup for PRP format SGLs(SCGCQ00415503)
 -NVMe: Command timing during NVMe init(SCGCQ00417756 )
 Add PLI control request for getting host memory page size(SCGCQ00418127 )
 -Move PCIe PL CLI commands to a new file(SCGCQ00419456)
 -SOP/PQI Device Initialization and base IO support(SCGCQ00426938)
 -MPI 2.6 Rev. B Feature Section 17.3.20.3: Add support for PCIe Device Page 2(SCGCQ00432568)
 -SAS3.5:DL: Implement UART commands to show debug data for PCIe Switches(SCGCQ00434290)
 -Add support to Hot Reset PCIe Device(SCGCQ00436875)
 -NVMe: command level error handling(SCGCQ00440187 )
 -Handle host FastPath IO completions while FastPath is disabled(SCGCQ00442786)
 -Added IO Unit Control Request in MPI v2.6 B to replace existing SAS IO Unit Control Request(SCGCQ00443274)
 -Use MPI 2.6 RevB Port Request flag define for FIS porting request in IoFlags field of SCSI IO Request message.(SCGCQ00443277)
 -MPI 2.6 Rev. B Feature: Section 17.3.2.8: Added BoardPowerRequirement and PCISlotPowerAllocation fields to IO Unit Page 7.(SCGCQ00443278 )
 -Added setting of DeviceInfo field on Device Page 0(SCGCQ00443285)
 -Add IT NVDATA to MR PL Object Library Release(SCGCQ00446684 )
 -Update AHCI variables to match latest MPI 2.6 release(SCGCQ00447777)
 -SAS3.5: Move ALADIN HW defines and register structures to separate header file under \common\hw.(SCGCQ00448020)
 -Add support for SATA translations which rely on data DMA for AHCI devices.(SCGCQ00448298)
 -Change SASIoUnitControl to IoUnitControl for Dauntless sources(SCGCQ00456975)
 -NVMe: Native SGL validation mode(SCGCQ00459734)
 -AHCI Error Handling (SCGCQ00459851)
 -AHCI: Add handlers for requester/completer errors(SCGCQ00459876 )
 -NVMe: FxCore IoError handling(SCGCQ00461439)
 -More SOP IU Error handling(SCGCQ00464488)
 -Update "pl status" CLI command to indicate PCI Device Type(SCGCQ00471842 )
 -Rudimentary Advanced Error Reporting support(SCGCQ00473858)
 -Update PQI and SOP header files to latest revision(SCGCQ00474533)
 -Add dump of all message frames to "pl dbg"(SCGCQ00476283)
 -Ventura: NVMe: Shutdown notification for NVMe devices.(SCGCQ00477716)
 -Ventura: Stang IOP control queue depth management (SCGCQ00478691)
 -SOP: Base device error handling during Init(SCGCQ00479555)
 -Ventura: PL Dual/Multiple Iop Completion Queue (MR(SCGCQ00481273)

 -NVMe: PCI legacy interrupt support(SCGCQ00481656)
 -Update PQI header to latest revision(SCGCQ00482105 )
 -Print additionl information on PCIe Error Messages and Fault on unhandled PCIe errors(SCGCQ00487994)
 -Encl Mgmt: Support for the new PBAM LED control and SGPIO HW block(SCGCQ00490950)
 -No check for good status in pliFpeGeneralErrorInterrupt((SCGCQ00490961)
 -Add and improve config space dump for debug commands.(SCGCQ00492503)
 -Ventura: Investigate Performance Monitors(SCGCQ00492549)
 -Add IOCount to Admin Commands(SCGCQ00494444)
 -SOP: Base device error handling for IO exceptions(SCGCQ00494457)
 -Cleanup the TxDMA dual context and DMA groups code based on new HW functionality in Intruder SAScore(SCGCQ00496009)
 -Improve Back End PCIe fault marker(SCGCQ00498145)
 -SAS Gen3.5 Additional PCI Encapsulated MPI Message Support (SCGCQ00498556)
 -Update PL for Colt changes in TxDMA TxCM Interrupt registers(SCGCQ00518333)
 -PL: SOP/PQI Task Management support(SCGCQ00521567)
 -Allocate from IOA Local RAM(SCGCQ00521570)
 -Ventura: Combo Serdes Wrapper Support(SCGCQ00521573)
 -Ventura FPGA: Support FPGA specific back end SerDes(SCGCQ00521574)
 -Ventura: Silicon Address Map Changes(SCGCQ00521681)
 -SAS3.5FW: Colt changes: Update register definitions for Queue Manager changes(SCGCQ00527271)
 -PL (Ventura): Gracefully handle some unexpected completions from NVMe target devices(SCGCQ00527872)
 -Enterprise PIM/POM setup(SCGCQ00552409)
 -Enterprise: register usage and indexing in the backend PCIe code(SCGCQ00552412)
 -Enterprise: base core initialization(SCGCQ00552422)
 -Ventura: Enterprise: sub(SCGCQ00552432 )
 -SOP SGL translation updates(SCGCQ00562155P)
 -NVMe: Update translations to the latest version(SCGCQ00562270)
 -Update SOP to latest revision (SCGCQ00563327)
 -NVMe: Extended Inquiry Data VPD page (SCGCQ00563906)
 -Port PL and CFGI library builds to ARM for Ventura(SCGCQ00564814)
 -NVMe: Support for Mode Sense (10) LLBAA flag(SCGCQ00571441)
 -Develope Boot Loader Build Process for ARM(SCGCQ00571692)
 -Ventura: Add support for new interrupts in Raptor SAS core(SCGCQ00572622)
 -Port Ethernet Library to ARM(SCGCQ00579966)
 -Added new function for safe backend PCIe writes(SCGCQ00603244)
 -Intruder: TLB changes to match new top(SCGCQ00603459 )
 -Update the PLI memory allocation code to account for multiple SAS cores(SCGCQ00603491)
 -Update Discovery code to support up to 32 phys/ports (direct attach only)(SCGCQ00605435)
 -PL: Update Discovery code to support up to 32 phys/ports (expander attach)(SCGCQ00605438)
 -Intruder PL: update to new IOA Cuda block in Charger(SCGCQ00606253)
 -Ventura: SAS Persistent Connection support(SCGCQ00612657)
 -Modify basetype.h to be device independent(SCGCQ00612747)
 -Ventura: Ventura Temperature Monitor Support(SCGCQ00612780)
 -Ventura: SAS Control Queue FIFO support(SCGCQ00612801)
 -Enterprise preparation: root complex organization(SCGCQ00613905)
 -Updated PCIe IO accelerator header files(SCGCQ00619567 )
 -PL: update SAS Core DCR interface for multiple SAS cores(SCGCQ00620384)
 -PL bringup on Intruder FPGA(SCGCQ00620516)
 -Intruder FPGA updates(SCGCQ00621476)
 -Ventura: Create fast POST memory routines using Neon similar to ARM memcpy(SCGCQ00622834)
 -PL support for multiple SAS cores during initialization(SCGCQ00623972)
 -Enterprise: EDS 1.11 header file(SCGCQ00624245)
 -Ventura: IOA (SCGCQ00628235)
 -Modified AHCI code to use new safe accessor functions for PCIe read/write(SCGCQ00630188)
 -Modified NVMe code to use new safe accessor functions for PCIe read/write.(SCGCQ00630198)
 -Handle phy lynk table interrupts on multiple SAS cores(SCGCQ00630409)
 -PL: Extend PL to handle port layer interrupts on multiple SAS cores(SCGCQ00630410)
 -PL: Extend PL to handle Tx interrupts on multiple SAS Cores(SCGCQ00630412)
 -Handle phy layer interrupts on multiple SAS cores(SCGCQ00630413)
 - (SCGCQ00633869)
 -Update the trackers and complete the porting for the interrupt handler functions.(SCGCQ00634613 )
 -Updated header files for hardware names(SCGCQ00637211)
 -Update PLI_SET_SOD_PARAMS as per new PLI spec(SCGCQ00637694)
 -PL: Add macro to get SAS core number from Device Handle(SCGCQ00638460)
 -PL(SCGCQ00638922)
 -Modified AHCI error handling to use new safe accessor functions for PCIe read/write(SCGCQ00639213)
 -Ventura: NVMe: update device information after a Format Unit(SCGCQ00639223)
 -PL: supportive changes for Tx and Rx interrupt handling for multiple SAS cores(SCGCQ00639788)
 -Add ALADIN support to Ventura. (SCGCQ00642196)
 -Replace PCIe read/write accesses to SOP/PQI devices that are currently performed using TLB mappings with safe accessor functions.(SCGCQ00642669)
 -Ventura: SIO/LED control enable PCI/SAS device activity support(SCGCQ00642853)
 -Ventura: SerDes header file changes(SCGCQ00643953)
 -PL(SCGCQ00644879 )
 -PL: update SMP Engine (initiator) to support multiple SAS cores(SCGCQ00646717)
 -Ventura: Local Chain Support (CR(SCGCQ00647786)
 -Ventura: IOA NVME SOP Hang Detection (CR(SCGCQ00647800)
 -Add multi SAS core support in lower layer functions called from phy interrupt handlers.(SCGCQ00648004)
 -Updated PL to add multi SAS core support for FW controlled spinup(SCGCQ00648006 )
 -PL: update phy/port configuration to handle multiple SAS cores(SCGCQ00649069 )
 -Update usage of IOC_NUM_PHYS(SCGCQ00649610)
 -Initial FxCore bring up(SCGCQ00649914)
 -PL: Change PhyNum in struct PL_INTR_SOURCE to represent chip phy number(SCGCQ00652141)
 -Ventura: Change readPIR() macro to something more generic(SCGCQ00652365)
 -Ventura: Enterprise: revisit base core init(SCGCQ00655157 )
 -Intruder PL:Changes needed for Link Reset to support multi SAS core(SCGCQ00660481)
- Change Serdes module code to account for multiple SAS cores(SCGCQ00660485 )   
  - Modify Diag commands to handle multiple SAS core.(SCGCQ00661114)
  - Intruder: modify SAS Core base address and size, and update FW effective address map(SCGCQ00661523)   
  - PL: power management code cleanup(SCGCQ00663208)
  - Enterprise: preparation for Enterprise interrupt and device interrupt support(SCGCQ00664180)
  - multi-SAS Core support to SAS Phy config pages(SCGCQ00665134)
  - Intruder: Register dump of all SAS Cores(SCGCQ00665865)
  - Backend PCI: add compile option for MSI(x  vector masking code(SCGCQ00668595)   
  - Backend PCI: move device interrupt info structure(SCGCQ00668627)
  - Enterprise: additional preparation for device INTx support(SCGCQ00668628)
  - PL Sim additonal work(SCGCQ00668850)
  - SOP: update init state machine(SCGCQ00669451)
  - Add check for Detroit PLB parity error by reading DCR regs(SCGCQ00669726)
  - Removed remaining Invader A0/B0 Hardware WorkaroundsSCGCQ00669729)
  - Intruder: Update plRemoveDevice to work with multiple SAS cores(SCGCQ00669830) 
  - Ventura: SIO/LED control initialization	(SCGCQ00671021)
  - Update code to clean up QM's linked list, for multi SAS core support(SCGCQ00673097) 
  - Ventura: SOP TM updates	(SCGCQ00675384)
  - Intruder: Adapt plDMATransQCleanup(  for Multiple SAS Cores	(SCGCQ00675684)
  - Intruder: Top level TM multiple SAS Core support(SCGCQ00675694)
  - Intruder PL: Update phy port config code when Auto Port Config is OFF(SCGCQ00676414) 
  - Intruder: Adapt target mode cleanup functions to multiple SAS cores(SCGCQ00677027)
  - Clean out MUTLI_SASCORE markers in plPortLayer.c(SCGCQ00680531)
  - Ventura: Enterprise: DM PCIe Core start of day configuration(SCGCQ00680765)
  - Ventura: Create Release ANSI builds for Validation(SCGCQ00682063)
  - Ventura: Enterprise: update header file for new product definition(SCGCQ0068282)
  - PL: Remove plCompileOptions.h from the list of files needed for pli	(SCGCQ00682887 )   
  - Cleanup some MULTICORE_SAS_WORK_NEEDED defines	(SCGCQ00683281)
  - PL: multi-SAS-Core work in plAhciMisc.c and plSataMisc.c (SCGCQ00683369)
  - Intruder: Update FPE completor error handling to support multicore	(SCGCQ00684383)
  - Intruder: Turn FPE SAS Completion Queue registers into an array like in Ventura	 (SCGCQ00685117  )  
  - Migrate GHS toolchain to version 6.1.4 (SCGCQ00685242)
  - Ventura: Enterprise: PCIe IO Unit Page 1 write handler(SCGCQ00686614)
  - Ventura: merge SAS phy devhandle and PCIe phy devhandle usage(SCGCQ0068667)
  - PL: Internal debugging information	(SCGCQ00687538)    
  - Intruder: modify PL build/release process to include IntruderFpga.xsd(SCGCQ00688174) 
  - PL: Starfish EDS v2.7 updates(SCGCQ00688251)
  - Intruder & Ventura: Consolidate Reply Destination defines across various Cuda cores(SCGCQ00688686)
  - Ventura: Update FPE Diag cmds for FPE registers(SCGCQ00688721)
  - Update SAS/Sata Task Management code due to Ventura HW changes(SCGCQ00689006)
  - Ventura: Create helper functions and macros to navigate between PCIe device and enumeration structures.	(SCGCQ00689874)  
  - Ventura: backend PCIe: revise devhandle macros(SCGCQ00690231)
  - Ventura: Enterprise: backend link speed/width control code	(SCGCQ00690945)
  - Code cleanup of PL_MULTI_SAS_WORK_NEEDED defines/comments(SCGCQ00691105)
  - Ventura: backend PCIe: link to root complex mapping	(SCGCQ00692020)
  - NVMe: improve fabricated WWID for non-1.1 devices(SCGCQ00693948)
  - Ventura: Support to manually add completion entry in to FxCore Completion queues; FPE or IOP(SCGCQ00694239)
  - Ventura: Support to send MID’s in FxCore FxRequestor engines to Exception queue for TM trapping(SCGCQ00694241 )   
  - Ventura: Support for HW CR to perform device handle check for PCIe device IO completions(SCGCQ00694244)
  - Ventura: Implement new PCIe Discovery SM(SCGCQ00694262)
  - Ventura: Enhance PCIe Discovery to support switches without DLL Link Active Reporting capability(SCGCQ00694264 )   
  - Intruder: Update plGetNumberOfSASCores to determine the number of SAS cores from CCR register(SCGCQ00695533)
  - Ventura: CSW Spico Firmware Image (SCGCQ00696945)
  - Intruder, Dauntless & Ventura: Update usage of PLISingleContextDMA to account for representing multiple cores (SCGCQ00700542)    
  - Intruder: implement HW WA for SCGCQ00696319 (SCGCQ00700743)
  - NVMe: modify idle wait during init	(SCGCQ00703473)
  - NVMe: slightly rearrange PCIe DevDetails NVMe flags	 (SCGCQ00705509)
  - SAS3.5: Separate out SAS Phy Power Management so we can compile out the code if it is not working properly.	 (SCGCQ00709570)    
  - Cleanup PL_MULTI_SAS_WORK_NEEDED in plDiagCmdPwrMgmt.c	(SCGCQ00710194)
  - Ventura: Process TM Marker Mid in PCIe DevH Mismatch error interrupt(SCGCQ00712814) 
  - Backend PCIe: debug code for backend/local address correlation	(SCGCQ00713761)
  - Add Multi SAS Core support to initiator added functionaility (SCGCQ00713914)
  - Intruder: Remove IOCount Increment/Decrement prints	(SCGCQ00715166)
  - More multi core upgrades to Target Mode code(SCGCQ00715204)
  - Fix access to initiator table for Target Mode(SCGCQ00716824)
  - (Target Mode  Update endiannes of SASAddress while adding initiator into Hw Initiator Table	(SCGCQ00716852)    
  - (PL  More Target Mode Multi Core support(SCGCQ00722556)
  - PL NVMe: Updates to internal structures	(SCGCQ00723588)
  - PL: Implement section 7.7 of the NVMe specification	(SCGCQ00723596)
  - PL NVMe: Asynchronous Temperature Events will be disabled under some conditions.(SCGCQ00723600) 
  - PL NVMe: Use the Namespace List command when available(SCGCQ0072363)
  - Replace LastHeadWrite with FLUSH_WRITE (SCGCQ00726746)
  - PL: cleanup of #if INVADER	(SCGCQ00728717)
  - Print SAS Core Number for top level interrupt print	(SCGCQ00728886)    
  - Enabled the FIS porting feature and SAS exception queue handler	 (SCGCQ00729510)
  - Ventura: CSW Added Implement PLI Interrupt Handlers	(SCGCQ00733171)
  - Add IOP start queue for secondary processor	(SCGCQ00734296)
  - Cleanup Power Management Port Width Modulation indentation for maintainability(SCGCQ00734411)   
  - PL NVMe: Save off the correct version number (SCGCQ00735758)
  - N/A(SCGCQ00738664)
  - Ventura: reject backend PCIe devices that do not support MSI-x(SCGCQ00740574)
  - Ventura: PL Dual/Multiple CPU Queue Task Management Support(SCGCQ00754472)
  - Intruder FPGA: Add/Update TxDMA prints to include SAS Core Num and other useful information.(SCGCQ00755010 )   
  - Ventura: add CPU number to Reply Dest define (SCGCQ00756765)
  - Ventura: Enterprise: update headers for new EDS	(SCGCQ00756824)
  - FW Controlled Spinup: Periodic NOTIFY (ENABLE SPINUP  primitives for legacy SAS drives(SCGCQ00757326)    
  - Removed an Unused PL Feature for IOA Completion Queue Interrupt Coalescing(SCGCQ00758603)
  - Extend MFG Page 17 fields to accomodate more phys(SCGCQ00759493)
  - Ventura: Initial Cache Snooping Settings (SCGCQ00759738)
  - Ventura: Add SAS AI Slave register definitions	(SCGCQ00764299)    
					
  - Intruder: Route Non-Auto TxFM Interrupts to SAS Exception Queue	 (SCGCQ00766711 )   
  - Intruder: Allow Multiple SATA FIS Port IOs Outstanding	  (SCGCQ00768012)
  - Enterprise: check in EDS parser script	 (SCGCQ00769343)
  - Ventura: Remove initialization of mismatch frame manager  (SCGCQ00771218)
  - Ventura: Add restart capability to PCIe discovery(SCGCQ00771838)
  - pl: add macros for SATA init state change location codes(SCGCQ00773360)
  - Fix FW use of HW context offset to match actual HW context offset(SCGCQ00776435)
  - pl: AHCI: add check for 64 bit addressing support(SCGCQ00776856)    
  - Backend PCIe: enhanced diag console commands(SCGCQ00785711)
  - Backend PCIe: remove 'pl pci cap' console command(SCGCQ00786396)
  - Changes needed in FW controlled spinup of SPL-2 SAS drives(SCGCQ00787379)
  - PL: Target mode multi sas core support in pliResourceAvailable( (SCGCQ00789417  )  
  - Ventura: Raptor EDS register changes	(SCGCQ00789641)
  - Ventura: add FPGA build with backend PCIe code	(SCGCQ00790217)
  - SAS3.5 cleanup project and remove all Invader out of Intruder/Dauntless	 (SCGCQ00793562)  
  - Ventura: Modify code for compatibility with Silverhawk core	  (SCGCQ00796039)
  - Ventura: Enterprise: update Enterprise header files	(SCGCQ00799993)
  - Ventura: Distribute PL Object Modules into PLI defined archives	(SCGCQ00801716)
  - Ventura: backend PCIe: attempt some backend PCIe image size reduction (SCGCQ00803550)
  - Ventura: PCIe discovery - additional changes required to support PLX 8732+8764 RDK.(SCGCQ00805421)    
  - Ventura: Enterprise: add error tracker(SCGCQ00806134)
  - Intruder: New Config Pages for ISTWI Controller and Device Information	(SCGCQ00806204    
  - Ventura: Enable multiple SAS core support (SCGCQ00811125)
  - Backend PCIe: revisit FxCore requestor cleanup during TM(SCGCQ00812748)
  - Ventura: Enterprise: start of day memory power state configuration(SCGCQ00812875)  
  - Ventura: Update FPGA link up procedure for new CSW	(SCGCQ00813927)
  - Aladin Core: Support Fast Trace Data Collection via UART(SCGCQ00816086)
  - Ventura: Enable new PCIe discovery(SCGCQ00816096)
  - Update pl utility functions to retrieve Hardware Context pointers to be remote core compatible(SCGCQ00816272)   
  - Intruder: Update SERDES settings	 (SCGCQ00816655)
  - Use SAS Core Num of Device when accessing SASCore Device Table	(SCGCQ00816868)
  - Tiger: Update/consolidate SAS Core Hardware Initialization for Tiger support(SCGCQ00817131)
  - SAS3.5FW: update to latest MPI v2.6 header files(SCGCQ00817142)
  - Ventura DA A/R: PCIe error handling - PDB Side configurations(SCGCQ00817996)
  - Ventura: backend PCIe: some bringup changes	 (SCGCQ00818337)
  - Handling errors from pliPortEnable( (SCGCQ00818760)
  - Update SATA related code to use new plGetSasHwCtxFromDevH(  vs plGetHwContext((SCGCQ00819473)
  - Tiger: Add PL FW support to account for External SED SAS Cores during MaxSasCorenum considerations(SCGCQ00819898)  
  - Ventura: Eliminate references to capabilities structures in DM and PCI core (hardware  files(SCGCQ00820930)
  - Ventura: Create Maverick.h header that compiles	(SCGCQ00820945 )   
  - Ventura: backend PCIe: some bringup changes	(SCGCQ00821615)
  - Change usages of plGetHwContext(  over to plGetSasHwCtxFromDevH( (SCGCQ00821648)
  - Ventura DA A/R: TM Code changes related to PCIe error handling.	(SCGCQ00821974)
  - Ventura DA A/R: FxCore Interrupt/exception handling related to PCIe errors.(SCGCQ00821979)
  - Implement PCIe error recovery by handling AER interrupt generated by root port for direct attached PCIe devices.(SCGCQ00821994)
  - Convert Target mode get HW context calls to get context via core number	 (SCGCQ00822301)
  - Aladin Core: Support Status Command via UART(SCGCQ00822308)
  - Convert SAS Core Hardware touch code to get Hardware Context using SAS Core Number	(SCGCQ00822565) 
  - pl: backend PCIe: modify TM device status check timers as in device init(SCGCQ00823052 )   
  - Ventura - SED Support for POM to communicate with remote SASCores added(SCGCQ00823424 )   
  - Ventura Tiger: add enumeration support for Tiger and Tiger emulator	 (SCGCQ00823434)
  - Tiger: Update num of Phys per chip usage to account for remote SEDs - Part 1(SCGCQ00823845)  
  - Ventura: Enterprise: PIM/POM mapping bringup(SCGCQ00824588)
  - Ventura: Update Impala header file for new location of CoreInstance(SCGCQ00824728)    
  - Send periodic NOTIFY(SPINUP  to legacy SAS drive under FW control(SCGCQ00824941 )   
  - Ventura: Use consistent method for printing DevHandle and Mid(SCGCQ00825825)
  - Ventura: Set RxLosFilterEn in Guinness PUB register to allow for SATA direct attached link up(SCGCQ00825867)
  - Modify PL to used CSW2.1 initialization and register definition and set number of core to 2 by default.(SCGCQ00825881)    
  - Cleanup of PLI I/F PIM/POM struct members (SCGCQ00828947)
  - Ventura: update stang header file to latest revision(SCGCQ00829025)  
  - Ventura: backend PCIe: device space may be mapped to either POM	 (SCGCQ00829752)
  - Ventura - PLI naming tweaks for PIM/POM (part 2  (SCGCQ00830094    )
  - Ventura Tiger- Update SOD memory calculation for SASCore Completion Queues to account for remote SAScores(SCGCQ00830799) 
  - Ventura SW A/R: AER interrupt handling for Switch topology (ER   (SCGCQ00830951)
  - Ventura: Issue task management for missing PCIe devices on DMD start.(SCGCQ00832556)   
  - Marlin: backend PCIe: support additional link configurations (SCGCQ00832638)
  - Compile out Slot ordered spinup support	(SCGCQ00833374)
  - Ventura SED support - add Initialize SASCore registers for Invader Based emulator (SCGCQ00833451)  
  - Ventura: backend PCIe: some bringup changes	(SCGCQ00833580)
  - Ventura: backend PCIe: PLI address pool tweak(SCGCQ00833813)
  - Ventura DA A/R: PCIe Error handling in NVMe IO path.(SCGCQ00834583)
  - Ventura: Support Raptor R10 and R31	(SCGCQ00834846)
  - Ventura: Add PCIe discovery to IO Unit Control Force Full Discovery Request processing	(SCGCQ00835044 )   
  - PL: Check in the latest serdes settings for Intruder A0 silicon	 (SCGCQ00835410)
  - Ventura: Support dual R31 Raptor cores	 (SCGCQ00836749)
  - Ventura: update FxCore queue search during Query TMs(SCGCQ00838827)
  - Ventura: Enterprise: ShellShimObThreshold FPGA hack	(SCGCQ00839546)
  - Ventura Tiger: Setup remote cores on Ventura IOA	  (SCGCQ00841008)
  - Release notes not needed. plSim is not released during a "standard" release.(SCGCQ00843993) 
  - Ventura: SGPIO Double Pump Mode support	(SCGCQ00846941)
  - Firmware Controlled Spinup: Move Spinup Timer callback(SCGCQ00846942)
  - Ventura: Remove Dauntless PCIe discovery implementation	(SCGCQ00848347)
  - Ventura: Enhance device handle allocation to support async PCIe device addition and removal(SCGCQ00851274)   
  - Updates to Ventura for Tiger emulator support (SCGCQ00851588)
  - Ventura: Add APB SAS Slave registers to gSASCore memory map	(SCGCQ00853334)
  - Ventura Tiger emulator support changes for setting correct Port on remote SAScore phy (SCGCQ00853684)   
  - Ventura: Add the APB slave registers to the debug dump	 (SCGCQ00857054)
  - Code changes to get PCI hot reset working	 (SCGCQ00857498)
  - Ventura: backend PCIe: updated CE binary image	  (SCGCQ00858138)
  - Need spurious interrupt checks.		(SCGCQ00860268)
  - Ventura: backend PCIe: link bandwidth management notification	(SCGCQ00862039)
  - Ventura: Add support for handling AXI interrupts in SAS Core(SCGCQ00862457)
  - Increase timeout value when stopping RxCtxMgr to 2 seconds (from 10ms  on the FPGA.	 (SCGCQ00865807)
  - Ventura: backend PCIe: enable maximum PCIe device count in FPGA DDR build	(SCGCQ00865951)
  - Ventura: Use Host initiated IO Fast path flag bit to determine Frame Ownership	 (SCGCQ00866323)
  - Handle PCIe MemRd, MemWr failures issued over Enterprise POB in Axi2Shell Bridge interrupt handler (SCGCQ00866777 )   
  - Ventura: Add R33 core support	(SCGCQ00867228 )   
  - Enable PortParity Error interrupt in TxContextManager	 (SCGCQ00868992 )   
  - Add SBR header information	(SCGCQ00872116)
  - Ventura: backend PCIe: tweaks to TM and interlocks with other subsystems(SCGCQ00874057)
  - Update IOA AxUser ID to appropriate value as fixed in bitstream release 3.8	 (SCGCQ00876791)  
  - TigerStryker: Add new defines for PSB and PDB builds Part 2	 (SCGCQ00883029)
  - Implement MPI 2.6 Active Cable Exception Event		  (SCGCQ00883606)    
  - Ventura: backend PCIe: clean up some TODOs (part 2 		  (SCGCQ00884601)
  - BL: First pass of adding conditional compilation for MMU and MPU	  (SCGCQ00885620 )   
  - Remove unused SATA_SPEED_BRIDGE compile option and code	 (SCGCQ00886420)
  - Ventura: control which NVMe SGL format to use.	 (SCGCQ00886974)
  - Tiger: IOA Init	 (SCGCQ00888287)
  - Tiger/Stryker: Separate PDB code into new define - part I (SCGCQ00888868)
  - Tiger: Various tweaks to allow FPE usage on FPGA	 (SCGCQ00894300)
  - PL: Cleanup SATL code when handling commands with immediate bit set	 (SCGCQ00895181)
  - Ventura: Update NVMe header files	 (SCGCQ00897151)
  - IOP: Update PBAM offsets with Tiger/Stryker configuration	 (SCGCQ00897540)  
  - PL: Update internal structures	 (SCGCQ00898645)
  - Don't honor the DO_NOT_SEND_TASK_IU flag for Host initiated TMs for PCI devices	(SCGCQ00903582)    
  - Ventura: Implement backend sas/pci protocol control	 (SCGCQ00904596)
  - Ventura: Update firmware to the latest revision of NVMe SCSI Translation Reference(SCGCQ00905171)    
  - Ventura: Header file changes	  (SCGCQ00905237) 
  - Create PEX registers header file(SCGCQ00905526)
  - Remove Dauntless Defines: Makefiles and build scripts.	(SCGCQ00905980)  
  - Removed Dauntless platform specific code from the backend PCI PL code base	(SCGCQ00905990)
  - Ventura: Add compile option to enable/disable AHCI Support(SCGCQ00908659)
  - Allow Unique SAS address for Direct Attached Sata Devices  (SCGCQ00908795)
  - Tiger/Stryker: CSR Handler (Cfg Read and Writes  (SCGCQ00910623)
  - Ventura: Make Some Fault Codes Unique	(SCGCQ00910652)
  - Ventura: Use CSW library to load nvdata phy parameters(SCGCQ00910735)
  - Ventura: backend PCIe: remove stale early FPGA hacks	 (SCGCQ00911513)  
  - Ventura B0: backend PCIe: changes for IOA stall prevention	 (SCGCQ00914682)
  - PL: Set the number of SAScores correctly  (SCGCQ00915868)
  - Disable PL_FEATURE_SED_SUPPORT(SCGCQ00915981)
  - Tiger/Stryker: PSB initialization(SCGCQ00918247)
  - Tiger/Stryker: MCPU Enumeration and Configuration of PEX ports and attached devices.(SCGCQ00918258) 
  - Ventura: Map WidePort activity group to GPIO pins	 (SCGCQ00919252)
  - Ventura: Remove SAS core SGPIO module support code	(SCGCQ00919473)
  - Ventura A0: Add support for B0 HW CR46 - PBAM InFrame activity mapping logic changes for PDB and SAS cores	(SCGCQ00919497)
  - Ventura: Add support for PCIe Port link status GPIO LED (SCGCQ00922878)
  - Ventura: Internal compiler option cleanup (SCGCQ00922908)
  - Update Ventura PL code for MPI/SED device enumeration (SCGCQ00924378 )   
  - Ventura: backend PCIe: link down handling tweaks  (SCGCQ00925766)
  - Ventura: backend PCIe: allow usage of 64 bit space for device BARs	(SCGCQ00926634) 
  - Add display of Serdes version info(SCGCQ00926684)
  - Ventura: PCIe error handling tweaks for SHEX stall conditions(SCGCQ00927522)
  - Ventura: Ensure uniqueness of PCI Bus Numbers for devices in the backend PCIe topology	 (SCGCQ00927968)
  - Ventura: backend PCIe: add support for not faulting on resource setup failure(SCGCQ00928542)
  - Ventura: backend PCIe: resolve "use MPI defined shift" TODOs  (SCGCQ00928552)
  - Ventura: Update Inquiry results for NVMe drives to be compliant with version 1.5 of the NVMe SCSI Translation Reference (SCGCQ00928876) 
  - Tiger: Remove PCI_PSB from build and use IOP/PL defines	(SCGCQ00932472)
  - Ventura: Update FxCore queue flag struct in the header file to match latest EDS	 (SCGCQ00934751)
  - Active cable Power management support for Intruder/Cutlass (SCGCQ00935460) 
  - Ventura: Update some PL prints to use the Program Counter(SCGCQ00936716)
  - PL: Remove old remote SED Driver code from PL(SCGCQ00937808)
  - Remove leftover Dauntless code from SAS 3.5 firmware codebase(SCGCQ00938267)
  - PL: Remove remote SAS core management(SCGCQ00938440)
  - Ventura/Marlin: backend PCIe: resolve some TODOs(SCGCQ00938516)
  - PL: Add support framework for received MPI events from downstream devices	(SCGCQ00938560 )   
  - Ventura: backend PCIe: add runtime control of PDB hardware workarounds	  (SCGCQ00938856)
  - Turn on satapmlastspeed bit in HW(SCGCQ00939406)
  - Tiger: Update SIL on POM access.(SCGCQ00939588)
  - Tiger: Add Pex HW related uart commands	 (SCGCQ00940378)
  - Ventura: backend PCIe: store NVMe init permanent failure reason	  (SCGCQ00941043)  
  - PL: Remove unnecessary bit from device data structure (SCGCQ00941747)
  - PL: Clean up SATA only fields in device information structure	 (SCGCQ00943357)
  - Create separate header file for Tiger CCR register definitions	(SCGCQ00944146)
  - IOP: Implement the macros for enabling/disabling config space for Tiger	 (SCGCQ00944747)
  - Tiger: get PCI_DEVICE=0 build working	(SCGCQ00945790)
  - Tiger: add support to disable Tiger PCI Backend enumeration(SCGCQ00947178)
  - Ventura: SE version of seri interface functions	(SCGCQ00947213)
  - Ventura: backend PCIe: configure some link speed related settings in the DM Core  (SCGCQ00947271)
  - Ventura: Use CCR data to set number of SAS cores(SCGCQ00949076)
  - Ventura: backend PCIe: A0 bringup changes (SCGCQ00950032)
  - Ventura: Set Tx Phase in CSW(SCGCQ00951098)
  - PL: Make SED attached SATA drives appear as a SAS drive	(SCGCQ00952485)
  - Ventura: Add all ASC/ASCQ's to scsi.h(SCGCQ00952486)
  - PL: Ventura-Tiger: Set Additional FPE Hardware Flags for SED Attached Devices(SCGCQ00953368)
					
  - PL: Add awareness for Avago's Cub expander (SCGCQ00954684)
  - Tiger PL: Internal PCIe switch should be masked from host(SCGCQ00964651)
  - Tiger: Handle POM errors(SCGCQ00964901)
  - Tiger: Implement DPC support(SCGCQ00965091)
  - Ventura: Add code to prevent PDB access if PDB PLL not locked(SCGCQ00966067) 
  - Ventura: backend PCIe: decrease verbosity of IEEE SGL to PRP translation debug prints (SCGCQ00968712)
  - IOP Logic for updating the NVDATA Flags to indicate Current Active Cable Power Exception.  (SCGCQ00981722)  
  - Ventura: Update IOA/FxCore register settings to the HW recommended values (SCGCQ00982700)
  - Tiger: integrate using combo serdes wrapper library for SERDES init	 (SCGCQ00987114)
  - Tiger: Add performance monitor support. (SCGCQ00987214)
  - Tiger: Multiple host support for CSR (SCGCQ00988657)
  - PL: Add interrupt handling for downstream MPI devices(SCGCQ00991252)
  - Tiger: Initial Veloce updates for Firmware	 (SCGCQ00991777)
  - Tiger: Implement PCIe Capability Structure for the upstream management port	  (SCGCQ00995103)    
  - Ventura: Enable DMA masking feature	(SCGCQ00995327)
  - PL: MPI device initialization and interrupt fixes (SCGCQ00996181)
  - Ventura: Configure the PLLs on SBus ring (SCGCQ00999504)
  - Ventura PL: Must return SCSI IO Errors from SED via correct code path(SCGCQ01002447)
  - Tiger: Implement firmware controlled PCIe message transmission on downstream ports.	 (SCGCQ01002884)
  - Tiger: Implement firmware controlled PCIe memory TLP transmission on downstream ports.(SCGCQ01002890)
  - PL: MPI Driver needs to use Atomic Request descriptors if available  (SCGCQ01003767)
  - PL: Add MPI Device information to pl pci prot CLI command(SCGCQ01004358)
  - PL: Force 128 byte payload size when supporting Tiger FPGA	(SCGCQ01004360)    
  - PL: Support MPI SED attached expanders	(SCGCQ01009315)
  - PL: Use message frames as reply frames for MPI driver	(SCGCQ01010464)
  - Tiger Ventura: Store secondary SED MPT endpoint in upper half of MPI device array and populate FPE device state table for remote drives	(SCGCQ01010549    
  - Tiger: Intial setup of Messaging Unit Hardware to operate in Tiger mode	(SCGCQ01011139)
  - Tiger: Add SED Init message	 (SCGCQ01012121)
  - Updated debug print for RxCtxMgr interrupts to deal with newly defined interrupts.	 (SCGCQ01012491)  
  - Tiger Ventura: handle IO replies from MPI device for IOs not started by FW path	 (SCGCQ01012812)
  - PL: Add code to support more than one reply queue for MPI SED (SCGCQ01013664)
  - Ventura PL: Improve support for PCIe Topology Change List events from SED(SCGCQ01014644)
  - Tiger: Ventura side Completion Q flusshing forTM handling for Tiger attach devices	  (SCGCQ01014796) 
  - PL: Remove pointer to hardware not present in Tiger	(SCGCQ01015022)
  - Ventura PL: Provide SED with DDR information from IOC	(SCGCQ01015368)
  - Ventura A0: Modify the current Tx DMA stop and clean method per HW suggestion	 (SCGCQ01015801)
  - PL: Ventura: Set up SED attached devices for dual path	 (SCGCQ01018560)
  - Tiger Ventura - if Tiger or Ventura fault, ensure the other side is faulted as well. (SCGCQ01019232 )   
  - Ventura/Marlin: backend PCIe: Link number field in PCIe Link Page 3	SCGCQ01019238)    
  - Ventura PL: Patch up IO count for IOs to SED attached devices (SCGCQ01019623)
  - Ventura PL: Improve pl pci prot CLI command for MPI SEDs	  (SCGCQ01019746)
  - Ventura PL: Organize MPI SED initialization routines into their own file	(SCGCQ01020470)
  - Ventura: Enable Active cable Management support	 (SCGCQ01021229)
  - Ventura: backend PCIe: preliminary support for specific vendor SRIS NVMe devices(SCGCQ01021633)
  - Tiger PL SED: Initial Handling of Task Managements to an SED attached end device(SCGCQ01023127)
  - Tiger FPGA: Implement Abort Task Set, LUN Reset and Clear Task Set to SED attached End devices	(SCGCQ01024838) 
  - Aero: Add support for Clang (ARM V8  Compiler Build	 (SCGCQ01025199)
  - Ventura PL: Add support for PCIe Device Status Change Event	(SCGCQ01026209)
  - Ventura Tiger: (PL  Add support to report IO counters for IOs started to remote cores (SCGCQ01026333  )  
  - Ventura Tiger: Implement internal Target Reset Task Management	(SCGCQ01027918)
  - Ventura PL: Configure MPI SED Driver to use different sized queues	(SCGCQ01028106)
  - Ventura: backend PCIe: count occurrences of some events for link quality debug	(SCGCQ01028168)
  - Tiger: remove IOcount inc/dec function prints by default (SCGCQ01028249)
  - Ventura Tiger: Report Tiger attached SATA devices as SATA devices in Ventura.(SCGCQ01031015)
  - Tiger: Create SED product specific files(SCGCQ01031950)
  - PL: Present SED attached NVMe drives as NVMe drives (SCGCQ01032861)  
  - PL: Combine SAS/SATA and PCIe DeviceType fields	 (SCGCQ01033353)
  - PL: Combine SAS/SATA and PCIe Parent device fields	 (SCGCQ01033578)
  - Support for fetching LBA from NVMe Drives in case of medium error.(SCGCQ01033882)
  - Tiger: Enable FW NonAuto RX HW auto drop of frames	(SCGCQ01034335)
  - Replace Core # and Subsystem in TM Start print with TM MsgFlags value(SCGCQ01035100)
  - Ventura: Enable TestMux captures on SAS core 1(SCGCQ01035102)
  - PL: Add configuration page handling for SED attached PCIe devices(SCGCQ01035127)
  - Ventura PL: Convert Expander and Switch DevHandles in Topology Change List Events	(SCGCQ01035243) 
  - PL: SAS Enclosure Add event must be sent prior to PCIe Topology Change List event(SCGCQ01035618)
  - Ventura PL: Force SED attached NVMe drives to look like SAS drives in IOA(SCGCQ01035852)
  - PL: Add internal debug commands	(SCGCQ01037236)
  - Ventura: backend PCIe: changes for use of new SERDES firmware image(SCGCQ01038439)
  - Ventura PL: Add initial support for SED removal(SCGCQ01039070)
  - Ventura Tiger: Add support for TMs to SED attached NVMe end devices.(SCGCQ01040085) 
  - Ventura: Add sris setting in CSW(SCGCQ01044034)
  - PL: Handle SED going missing from the PCIe topology	(SCGCQ01044041)
  - Ventura Corrective Actions for Board Over Temperature Conditions (SCGCQ01044068)
  - PL: Configure PCIe switch BARs	  (SCGCQ01049391)
  - Tiger: remove R35 SAScore support(SCGCQ01049417)
  - Tiger: Add R42 ECO 0x01 sascore version	(SCGCQ01057706)
  - PL: Add support for memory translation in SAS Core	(SCGCQ01058395)    
  - Ventura: Add device side SPICO FW version to pliShowVersion((SCGCQ01062566)    
  - Tiger: Get Tiger to compile with PL_FEATURE_CSW_LIB enabled	(SCGCQ01063627)    
  - PL: Support Translation of Additional Log Pages	 (SCGCQ01067698)
  - Tiger Ventura: Don't dump SED message MIDs in pl mids (SCGCQ01071138)
  - SCSI over PCIe (SOP  Feature Removal(SCGCQ01071351)
  - Ventura PL (Tiger : Reorganize PCIe Topology Change List Event handling	(SCGCQ01073806)
  - PL: Improve MPI Message Print to include MID and correct PCI LinkRate conversion macro	 (SCGCQ01073878)  
  - Tiger A0: PCIe Link Configuration Setup	 (SCGCQ01076376)
  - Add new seri functions to interface with CSW library (SCGCQ01076389)
  - Ventura PL: Firmware should identify which path is connected and only initialize the primary path  (SCGCQ01080031)    
  - Makefile cleanup for SCSI over PCIe (SOP  Feature Removal (SCGCQ01080155)
  - Ventura/Marlin: backend PCIe: allow FxCore FPE completion queue to be placed in IOA Local RAM(SCGCQ01081056)
  - Ventura B0 default DMA Q masking settings	 (SCGCQ01082715)
  - Add debug information to ring buffer when PLLs fail to lock		(SCGCQ01083258)
  - Ventura: Move GPIO LED Data Mux source selection configuration from IOP to PL	(SCGCQ01083822)
  - Enabled Accelerator Coherency Port (SCGCQ01086077)
  - Tiger: Implement A PCIe Backend Function to Check if the Root Complex is Enabled(SCGCQ01087447) 
  - Ventura PL: MPI Numbers must be allocated per the configuration parameters(SCGCQ01087579)
  - Update Tx EQ settings to recommended default values	 (SCGCQ01088723)
  - PL: Get Encapsulated NVME I/O to work from Ventura to Tiger(SCGCQ01088802)  
  - PL: Add inline function for setting device manager bit  (SCGCQ01090086)
  - Ventura PL: Add support for SED specific resource mapping and mapping information retrieval		 (SCGCQ01091608 )   
  - Aero: modifications to compiler optimizations (SCGCQ01092420)
  - Aero: changes to get PL to compile with clang	  (SCGCQ01094536)
  - Ventura PL: Improve SED Config Page requests to allow for large pages (SCGCQ01095058)
  - PL: Hardware automated DATA FIS(s  DMA for SMR ReportZone SATL for faster proccessing (SCGCQ01107729)  
  - Ventura/Marlin: backend PCIe: use alternate means of generating mem space accesses (SCGCQ01108244)
  - pl: NVMe: when checking for device idle or ready, check once only per call(SCGCQ01110208)
  - Ventura/Marlin: backend PCIe: rearrange PDB medium priority interrupt handlers	(SCGCQ01110330)
  - Ventura/Marlin: backend PCIe: add multiple structure support to a PL internal search function(SCGCQ01110340)  
  - Ventura: Add B0 Pl recognition	  (SCGCQ01112241)
  - Ventura/Marlin: backend PCIe: update to latest compute engine binary image (SCGCQ01116715)    
  - Aero: create aero base address map	 (SCGCQ01123955)
  - Ventura: add Link field to the PCIe Link configuration pages (part 1  (SCGCQ01124182)    
  - Ventura: Add FxCore Exceptions Count to pl stats command(SCGCQ01124245)
  - Ventura: add FPE CPU1 performance counters to "pl fpe stats"(SCGCQ01124430) 
  - Ventura: Update Timer Adj 1 register for optical	  (SCGCQ01127529  )  
  - Ventura/Marlin: backend PCIe: support for SRIS enable in PCIe IO Unit page 1 phy data (SCGCQ01130582) 
  - Ventura: Report PCIe init status in IOC Exceptions	SCGCQ01130590)
  - PL: Added new debugging support	  (SCGCQ01132375)
  - PL: backend PCIe: always print LBA for NVMe read/write breakup IOs (SCGCQ01140426)
  - Ventura: Update MST with current MST info on timer error completions to IOP	  (SCGCQ01141751 )   
  - pl: NVMe: additional encapsulated request error reporting	 (SCGCQ01150880)
  - Ventura B0: backend PCIe: enable NVMe completion starvation prevention (SCGCQ01169187) 
  - Ventura/Marlin: backend PCIe: handle switch attached hot add max payload size mismatch	(SCGCQ01172361)
  - Implement TM history logger	 (SCGCQ01173976)
  - Addition of two events to Active Cable Exception Event Data. (SCGCQ01181278)
  - PL Sim: Update to compile  (SCGCQ01181402)
  - PL: Initialize LED Data Select Register	 (SCGCQ01183299)
  - PL: Additional debugging information	(SCGCQ01190215)
  - Reduce the number of Target Resets started when a missing device returns  (SCGCQ01205601 )   
  - Support VPP backplane LED management for NVMe x4 device Slots (SCGCQ01206050)
  - Ventura/Marlin: backend PCIe: allow user to disable ECRC for testing (SCGCQ01209929)
  - NVDATA is now required to match SBR PCE IDs, or MR card will assert	  (SCGCQ01214162)
  - Ventura: Print decimal versions	(SCGCQ01217493)
  - Marlin: backend PCIe: bringup changes for Marlin B0	(SCGCQ01232332)
  - Ventura/Marlin: backend PCIe: enable PCIe extended tags	(SCGCQ01254735)
  - Ventura/Marlin: allow IOP to direct PL to not allocate secondary CPU queues	(SCGCQ01263302)
  - Ventura/Marlin: backend PCIe: aggressively retry unreliable DA links during discovery  (SCGCQ01264003 )   
  - Support added for hot swap of NVMe drives(SCGCQ01264585)
  - Ventura: Updated Marlin B0 SATA Rx EQ Values	 (SCGCQ01269428)
  - Converted SMP Start debug print to standard Dev:MID format	(SCGCQ01270121)
  - Ventura/Marlin: backend PCIe: SRNS	 (SCGCQ01273153)
  - If the profile type is not supported on a downloaded image, the image will not get flashed.	 (SCGCQ01277489 )   
  - SCONS: Add Doxygen builder(SCGCQ01282782) 
  - Add source utilities	(SCGCQ01287449)
  - Add debug string builders	(SCGCQ01288927)
  - Add "Incompatible with Profile" event(SCGCQ01289924)
  - Enumeration of drives in certain OEM platform	 (SCGCQ01291036)
  - Add via file source utilities	(SCGCQ01291806)
  - Unified implementation of init buffer by dynamic allocation for SAS/NVMe mixed mode support	 (SCGCQ01299270)  
  - Core 1 uses Core 0 for nvram/flash access in TTY.(SCGCQ01302263)
  - Add display of CSW library version to debug output	(SCGCQ01306722)
  - VMware pass-through controller - No Time Sync after VM with PCIe device starts	(SCGCQ01307584)
  - Firmware returns only firmware supported profile id data for Host Appl Get Profile command	(SCGCQ01310346 )   
  - Enumerate GPIOs based on CCR  (SCGCQ01319860)
  - Setting up CPLD GPIO pins for CPLD online Update on Perc10 Controllers(SCGCQ01334575)
  - Support merging of multilple define sections from multiple yaml files.	 (SCGCQ01351246)
	(SCGCQ01354358    Opened))
  - Undo mon.c version number change introduced by SCGCQ01367090. (SCGCQ01367198)
  - Store the RAID SubDevID in NVRAM to have a reference to original RAID-ID - NVRAM changes (SCGCQ01388735 )   
	(SCGCQ01389581)
  - Improve Scons error handling (SCGCQ01390029)
  - Integrate phase-4 PL library 04.25.01.00 (SCGCQ01391584)
  -Older FW without NVME passthru support) breaks with NVME passthru capable components(SCGCQ01406091 )    
  - Add support for fan-out topology enumeration  (SCGCQ01423739)
  - Integrate MR PL-SCS Libs: SASFW_Ventura_Phase_5.0 04.250.09.00	 (SCGCQ01425554)
  - Enable PI on OEM controller (SCGCQ01445084)
  - PL: Add Code to Correctly Determine Mid for Rx Context Non-automated Interrupts	(SCGCQ01472512)
  - Look into Qfull handling (SCGCQ00081065)
  - Gen3: TLR	(SCGCQ00090039)
  - Update firmware to correctly dump all SAS Core registers	(SCGCQ00090999)
  - Diagnostic support updates for Colt  (SCGCQ00095010)
  - Need a mechanism to cover up IO failures due to discovery lag in PL	 (SCGCQ00100078)
  - [Internal Use Only] Control of Loopback mode through the UART	 (SCGCQ00126580)
  - pl: Power condition support in SATL - mode page 0x1A	 (SCGCQ00131186)
  - Update the Quiesce IO/TM/SMP code for gen3 generic availability	 (SCGCQ00131981)
					)
  - Thunderbolt: The B0 revision handles the SAS clock setup differently.  (SCGCQ00132812) 
  - Gen3 PwrMgmt: Add IOP & PL infrastructure for chip-wide power management modes	 (SCGCQ00136946)
  - TxDMA error handling update for NonAuto Bit implementation	 (SCGCQ00141867)
  - EDFB: watch for IT Link Layer IntStatus1 UnknownAddrFrameStat bit (SCGCQ00142858)
  - Allow smp to work for invader(SCGCQ00143184)
  - add ring buffer prints to EDFB code to assist with dev test	 (SCGCQ00144233)    
  - Write the magic keys to enable Detroit register access (SCGCQ00144420)
  - add the actually enable/disable calls to the PLI device/all enable/disable cotnrol request handlers		 (SCGCQ00145469)  
  - change FPE exception INVALIDE_DESCRIPTOR handling from doing an  reply to just handing off to IOP	  (SCGCQ00146110)    
  - FPE - Detroit EDS 1.1 Impacts on Fast Path firmware	 (SCGCQ00146766)
  - TBM: Host posted Extended Buffer has to be 16KB aligned	(SCGCQ00149045)
  - basic register updates for Colt EDS 1.21	 (SCGCQ00149149)
  - need to set bit 22 of RxFrm Config reg to 0	 (SCGCQ00149246)
  - pl: Enable a couple new interrupts in RxCM	(SCGCQ00150044)
  - PL: Fix prints in RxCM as the number of interrupts has grown and won't fit nicely into the current print (SCGCQ00150052)  
  - FPE: need to add an additional flags parameter to pliStartScsIO(SCGCQ00151001)
  - SAS-3 Add Pl Diagnostic Commands to Set FPE Continue Bits	  (SCGCQ00153609)
  - Disable SingleContextMode.	(SCGCQ00154829)
  - Add uart command to send an abort task to an outstanding io to a specific device(SCGCQ00155180)
  - Implement Extended Manufacturing Page 40 and 41. These two pages replace mfg page 3.(SCGCQ00155477) 
  - Add RxEEDP handling for Non Automated IO cases	(SCGCQ00155573)
  - FPE: update detroithw.h to Detroit EDS v 1.32	(SCGCQ00157011)
  - Add handling for TxCtxMgr non auto interrupt for sata devices.(SCGCQ00159013) 
  - Obsolete Man Page 15(SCGCQ00159985)
  - Update the register definitions as per Colt EDS 1.3	(SCGCQ00160461)
  - Implement functional section changes as per Colt EDS 1.3.(SCGCQ00160464)
  - CSET: Fixing debug string issues - (SCGCQ00156731  ADDITIONS (SCGCQ00160874)  
  - Round 2: remove more gen2 workaroudns that aren't enabled  (SCGCQ00162068)
  - Add a print for the Fault 0x5002 case(SCGCQ00162601)
  - TBM: Set TraceType for devices from host(SCGCQ00162901 )   
  - Round 4: gen2 HW WA removal	(SCGCQ00163955)
  - Cleanup plScsiIo.c	SCGCQ00165973)
  - Task Management Complete code cleanup(SCGCQ00166006)
  - pl: Remove unnecessary workaround code	 (SCGCQ00166702)
  - Add PLI control request to specify power management modes for Cuda fast path engine. (SCGCQ00167819 )   
  - Round 5 of gen2 WA removal(SCGCQ00168602)
  - TM: Update TM code to use macros for all accesses to hw context area. (SCGCQ00171264)
  - Don't set ArbMode[2] bit for spinupconfig (SCGCQ00174793)
  - FW needs to set some bits in TxFM at init/SOD to help with performance - BT700	 (SCGCQ00177397 )   
  - HW WA for BT COSEDA 790 - setup starfish regs as the HW defaults are incorrect  (SCGCQ00179616) 
  - Remove [SAS2Core] 1656(SCGCQ00180309)
  - FPE: disable FPE Timer when faulting (SCGCQ00181784)
  - Handle new RxCtxManager interrupt in B0	(SCGCQ00183299)    
  - Bring plSasCoreCleanup.c up to coding standards	(SCGCQ00185717)
  - comment out some code that's causing problem because of the known hw bugs	(SCGCQ00186491)
  - define another serdes register	(SCGCQ00187398)
  - Gen3 PwrMgmt: Wide Port Power Management to support 'Communicated Intent Modulation Scheme'	  (SCGCQ00188249)
  - Update TM to utilizie B0 RxFM change that will force HW to look at ForceIOPath bit in Hw Context vs cache (BT SASCore 713  (SCGCQ00193703 )   
  - Make SMP requests high priority and ensure they don't get queued behind other contexts(SCGCQ00200476)    
  - Invader A0: Add CLI command to dump complete Cuda's MST and DST regs(SCGCQ00201734)
  - Invader B0: BT [invader] 895 - f/w WA removal and changes to accomodate RTL fix	(SCGCQ00203339)
  - Gen3: MPI PowerManagementControl request msg parameters need to verified before processing.	(SCGCQ00203386)
  - Add a register definition(SCGCQ00203389)
  - Support to handle Unconfirmed Responses reported by SAS HW	 (SCGCQ00205974)
  - Dif Memory Threshold need to be initialized to a different value.(SCGCQ00207198)  
  - Need a mechanism to enable snoop regions in SAS	 (SCGCQ00210177)
  - Gen3: Update the Colt Revision Numbers	(SCGCQ00213007)
  - Invader A0: BT [invader] 1279 - Firmware workaround	 (SCGCQ00213444) 
  - Invader PLB snoop region configuration	(SCGCQ00215430)  
  - Cleanup task management start function and keep all hw cleanup in one spot (SCGCQ002184560)    
  - Gen3 : SAS core parity bit checking	 (SCGCQ00218757)
  - check in new serdes settings (2.14 	 (SCGCQ00218813)
  - Set default value of PL_SATA_DATA_BLK_RES to 0xD	(SCGCQ00219445)
  - Change the default value of the TimerCount register in RxFM to 0x1FFFF	 (SCGCQ00219981)
  - Invader Performance Improvements (Part 1  (SCGCQ00221359)
  - Update TxFM cleanup code for gen3(SCGCQ00224494)    
  - Update TM Tracker counters	(SCGCQ00225192)
  - Update hardware cleanup code to flush colt register writes when needed	  (SCGCQ00226955)
  - Starfish register update so that Invader-Cobra link up at 12G reliably	  (SCGCQ00233702)
  - Update the serdes register again to allow invader-cobra to link up at 12G reliably	(SCGCQ00234909)
  - Investigate if not setting up MsgUnitOffsets in FPE (the PLI params pass 0  works and/or if any changes are need to enable it	(SCGCQ00242893 )   
  - Active Cable Management: handle I2C errors	 (SCGCQ00245966)
  - Put code for BT 1486 in WA define(SCGCQ00246445)
  - Increase trace buffer entry timeout and add more debug on the D204 fault.(SCGCQ00247199)
  - Invader A0: (Hw Workaround  RxDma in target Mode (with AutoStatus=0  Clearing MidValid before FinalEEDP frame (SCGCQ00257902)  
  - Update B0 WA matrix for all fixed FPE issues (SCGCQ00261863)
  - Serdes settings to help with back channel training	SCGCQ00304268)   
  - Target Mode Performance Optimizations	 (SCGCQ00304799) 
  - Added B1 SAScore Recognition	(SCGCQ00312649)
  - SCSI to NVMe dataset management translations	 (SCGCQ00341219)
  - Need initializtion of message table resources for IOA changes	(SCGCQ00348165)
  - (IOP  Add option for tail printing of Ring Bufffer and Trace Buffer(SCGCQ00356717)   
  - SATA FIS Porting feature support(SCGCQ00357509)
  - SAS Gen3.5 FW Spinup Control Implementation	 (SCGCQ00360815)
  - [Dauntless]: SGL Translation - IEEE-64 to SOP/PQI (SCGCQ00362773)    
  - Added new internal tool, no change to FW(SCGCQ00362950)
  - (STANG  Add support for new parity an other faults	(SCGCQ00364223)
  - Added support for async removal and insertion for PCIe devices.	(SCGCQ00377853 )   
  - Added support for new SAS core versions	(SCGCQ00379298)
  - Added support for handling new Stang exceptions	  (SCGCQ00379989) 
  - pl: pci: DevHandle allocation for PCI switches	(SCGCQ00380149)
  - (IOA  Add compute engine initialization debug capability(SCGCQ00381819 )   
  - This week's NVMe related changes(SCGCQ00383672)
  - FW Read/Write IO Path base functionality(SCGCQ00400466)
  - FW Read/Write IO Path - Additional PCI protocol Helper functions (SCGCQ00400473) 
  - Use generic IO context structure throughout the NVMe code (SCGCQ00400554)
  - Added support to detect invalid AHCI PRDT (SCGCQ00401374)
  - Added code to support new high order bits register for scripts physical addresses(SCGCQ00406167)
  - (IOP  Add dump of CE Script Version (number and date  to the IOP SHOW VER command  (SCGCQ00412128)  
  - Use new fastpath express hardware when possible	  (SCGCQ00414087)
  - (PL-TBM  Change the Trace Buffer Manager so that faults are decoded better	 (SCGCQ00415382)    
  - SAS Gen3.5 Additional PCI Encapsulated MPI Message Support(SCGCQ00418649)    
  - Firmware Support for NVMe encapsulated MPI message	 (SCGCQ00420063)
  - Add base PCIe Task Management and AHCI device Task Management support (SCGCQ00420317)
  - Added support for translating PLB/DDR addresses in simple SGEs for AHCI devices	 (SCGCQ00420512) 
  - (PL  Add additional checks to FPGA to avoid invalid defects(SCGCQ00420887)
  - NVMe: Add PLB-NTA check to IEEE SGL translation code	  (SCGCQ00420919)
  - Added code to reject firmware translation of chain to AHCI PRDT format	  (SCGCQ00421777)  
  - Add ALADIN tracing support in PL  (SCGCQ00423378)
  - (IOA  Add code to activate Dynamometer and StopOnDMA features in Dauntless(SCGCQ00425000)    
  - PCIe IO Unit Page 1 NVMe Max Queue Depth  (SCGCQ00432741)
  - MPI 2.6 Rev. B Feature: Move all SAS IO Unit Page 4 Spinup Control and PortEnable functionality to IO Unit Page 11.	 (SCGCQ00433597)    
  - Need better way to set up PDB POMs	(SCGCQ00436942)
  - Add Stang Exception error handling for SOP	 (SCGCQ00441252)
  - Update PQI to latest revision  (SCGCQ00442263)
  - Implementation of SATL handling while the SATA drive is in security 'frozen' state(SCGCQ00443282)
  - Added PCIe IO Unit Page 4.(SCGCQ00443286)
  - Add support for emulated NVME target device using Thunderbolt controller(SCGCQ00449055)
  - Handle PCIe Fx-FPE completion queue wrapping while manually adding TM entries. (SCGCQ00449817)
  - NVMe: Start device initialization earlier (SCGCQ00449822)
  - New IOP Interface to allow mapping of larger memory resources (>1G  to backend pci space(SCGCQ00455575)    
  - Additional NVMe init error handling	(SCGCQ00457350)
  - AHCI: Add handlers for IO and port errors (SCGCQ00459853)
  - AHCI: SGL translation for SATA passthrough commands	(SCGCQ00466204)
  - Ventura: Populate Slot information for PCIe devices	 (SCGCQ00468835)
  - Modify SOP SGL translation to handle skipcount before checking DLAS	 (SCGCQ00476181)
  - Create and use generic PCI and PCI Express headers	 (SCGCQ00477114)
  - Debug command for dumping Stang queues (SCGCQ00480032)
  - Ventura: NVMe 1.1 SGL Support(SCGCQ00481258)
  - Allow TxDMA dual-context capability during non-FCS connection	  (SCGCQ00495917)
  - Changed a variable name that was too similar to another variable to prevent confusion and misuse of the variables (SCGCQ00504528)  
   Implement support for PCI device queues and other structures to be placed in user defined memory(SCGCQ00521487 )
  - Ventura: Update CCR Register Definitions(SCGCQ00521691)
  - Ventura: IOA – Impala IO Accelerator Cuda Trace Buffer Manager Block Bring Up(SCGCQ00522532) 
  - Ventura: IoCount changes for backend PCIe devices(SCGCQ00527858)
  - Enterprise: header file	(SCGCQ00552408)
  - Ventura: Enterprise: toplevel interrupt handler	(SCGCQ00552429)    
  - Enterprise: backend device interrupt configuration and handling	 (SCGCQ00552447  )  
  - Enterprise: root complex changes, part 1 (SCGCQ00552480)
  - Port SPI library build to ARM(SCGCQ00570147)
  - NVMe: a couple of mode page tweaks	  (SCGCQ00572583)
  - Create initial build of IOP for ARM	 (SCGCQ00577404)
  - Added code for safe back end PCIe memory reads(SCGCQ00603243)
  - PL: infrastructure for supporting multiple SAS cores(SCGCQ00603478 )   
  - PL: Determine the number of SAS Cores present(SCGCQ00603493)
  - add Intruder FPGA build	(SCGCQ00604632)
  - Ventura: POC7 Map Update(SCGCQ00606237)
  - SATL: Changes to SCSI Format Unit translation (SCGCQ00606271)
  - PL: Update SATA device support in PL for direct-attach drives to account for multiple SAS cores	 (SCGCQ00606873 )   
  - Updating IO path to take multiple SAS core into account (SCGCQ00607970)
  - Allow for separate Ventura and Intruder versions(SCGCQ00610916)
  - Ventura: SAS Initiate Close support (SCGCQ00612661)
  - Ventura: DMA Queue Masking support	(SCGCQ00612672)
  - PL: Implement newly added SAS request counters in IOA (SCGCQ00624070)
  - Removed gplPciDeviceDma	(SCGCQ00628093)
  - Enterprise: allocate memory at SOD for generic message data queue  (SCGCQ00629194)
  - Extend PL to handle link interrupts on multiple SAS cores (SCGCQ00630405)
  - Extend PL to handle queue manager interrupts on multiple SAS cores	(SCGCQ00630407)
  - PL: Extend PL to handle Rx interrupts on multiple SAS cores	(SCGCQ00630414)
  - Extend SAS config register and SAS slave interrupt handlers in PL for multiple SAS cores(SCGCQ00630415) 
  - PL: Convert gplInterruptTracker into an array to track interrupts on multiple SAS Cores (SCGCQ00630416)
  - Updated IOP interrupt handler function to handle multiple SAS Cores.(SCGCQ00632495)
  - Modified AHCI initialization to use new safe accessor functions for PCIe read/write	 (SCGCQ00639096)
  - NVMe: several SCSI-NVMe related changes(SCGCQ00642831)
  - UTILITY: Add memcfg utility for ARM products(SCGCQ00642860)
  - Support both SAS cores using same StarFish instance on FPGA	 (SCGCQ00644337)
  - Update link reset state machine to handle multiple SAS cores(SCGCQ00645143)
  - Ventura: POC8C Bringup	(SCGCQ00646636)
  - Update Open Reject Phy Hopping workaround to indicate it's fixed in parts beyond Invader C0  (SCGCQ00648223)  
  - Ventura: Replace gDetroitCore with gIoaCore(SCGCQ00652323)
  - Update plGetNumberOfSasCores(  on Intruder FPGA (SCGCQ00654341)
  - Updates for FPGA phase 0.3	(SCGCQ00654885)
  - Ventura: Update to latest Impala EDS and more Initialization changes(SCGCQ00657743) 
  - Intruder: Remap SASCORE1 in virtual address space with no overlap (SCGCQ00660501)
					
  - Removed unneed HW WAs that were only for Invader A0/B0 parts(SCGCQ00661628) 
  - Make SasCore Number the first argument	 (SCGCQ00664318)
  - Add Intruder Specific Define for Number of SGPIO Instances	 (SCGCQ00664340)
  - Ventura: Map remaining cores as described in the original Ventura map up to POC10 (SCGCQ00667112  )  
  - Enterprise: PDB MSI/MSI-x handler compatible with Enterprise(SCGCQ00669530)
  - Update STALL_NEW_FRAMES WA in plTimerCallback to work with multiple SAS cores	 (SCGCQ00669870) 
  - Handle Power loss interrupt for NVMe devices (SCGCQ00672240)
  - Modify Tx FM Cleanup code for dual SAS core support	 (SCGCQ00672803)
  - Update plRxDmaEngineReset to support multiple SAS cores	(SCGCQ00672915)
  - Modify functions that call plRequestFWBreak to pass the chip link number as the argument (SCGCQ00673022)  
  - PL: Port Width Modulation Algorithm (Power Mgt  to account for multiple SAS core  (SCGCQ00673054)
  - Use Quad related macros in code	 (SCGCQ00673111)
  - Intruder: Firmware Dual context settings cleanup and setting dequeuing modes. (SCGCQ00674213)  
  - Intruder: Adapt plTxTransportCleanup(  for Multiple SAS Cores(SCGCQ00675483)
  - Update Rx Transport cleanup code to account for Multiple SAS Cores	 (SCGCQ00675651)
  - Backend PCI: generate Set Slot Power Limit message	  (SCGCQ00676417)
  - Intruder: cleanup plRxCtxMgr.c PL_MULTI_SAS_WORK_NEEDED	(SCGCQ00680218)
  - Enterprise: tie legacy/MSIx interrupt handlers in with HW interrupts	(SCGCQ00680763)
  - Ventura: Enterprise: move backend lane dependent code in PCIe Device Manager	  (SCGCQ00684295 )   
  - PL: final cleanup of PL_INFO NumPhys and HwNumPhys (SCGCQ00685227)
  - Ventura: Integrate PCIe Discovery with Port Enable handling	 (SCGCQ00694260)
  - Ventura: Update Impala header to the latest version	(SCGCQ00696980)
  - Intruder: (IOP : Return correct iocStatus if the board has a higher power requirement than the PCI slot was allocated  (SCGCQ00706279  )  
  - Intruder: Add multicore support for certain target Mode functions(SCGCQ00710176)    
  - Add QM Exception Queue Registers to PL Diagnostic Code	 (SCGCQ00710465)
  - Provide interface to IOP to get local address to backend PCI address mapping.	  (SCGCQ00712817)  
  - Add Multi SAS Core support for Target Mode Hardware cleanup	 (SCGCQ00712972)
  - Improve handler for MCE STATE MACHINE DEBUG TIMER Expird interrupt (SCGCQ00714598)
  - Replace PL_SAS_CORE_0 usages with something more descriptive(SCGCQ00715199)
  - Add prints of CDB and LBA for 600X fault missing IOs(SCGCQ00715660)
  - Intruder PL: Add multicore support for setting/clearing busywhenhalfbusy global flag (SCGCQ00739392 )   
  - Dauntless: Build related changes (SCGCQ00765117)
  - Remove fast path development test support(SCGCQ00769248)
  - Ventura: Shifting of LSI-specific Phy Event Counter encoding(SCGCQ00769439)
  - pl: Add some sanity checks for backend phy, port, SASCore mapping	 (SCGCQ00771332)    
  - PL: Target mode PL_MULTI_SAS_WORK_NEEDED cleanup  (SCGCQ00780092)
  - Undo the firmware changes for workaround of Hardware defect about ArbMode[2] bit (SCGCQ00781194)
  - Ventura: Update PL hardware workaround table(SCGCQ00788132)
  - Ventura: PCIe Discovery should yield to the IOP scheduler(SCGCQ00789678)
  - PL: Rearrange the PCI I/O context structure to prevent accidental use of restricted HW context area. (SCGCQ00791459)  
  - clean up references to global variable in code comments (SCGCQ00793219)    
  - Cleanup of PL_MULTI_SAS_WORK_NEEDED in comments	 (SCGCQ00793224)
  - PL NVMe: Minor updates to NVMe protocol files(SCGCQ00799847)
  - Ventura: PCIe discovery - improve memory resource assignment to backend PCIe devices (SCGCQ00804421 )   
  - Ventura: backend PCIe: configuration of host side mapping resources	  (SCGCQ00805418) 
  - Modify PL call that translates PCI to local address to account for POM scheme used in Ventura	 (SCGCQ00807521)   
  - Remove Sas Port Virtualization(SPV  code which has been defeatured	(SCGCQ00813465)
  - Add PL_FEATURE_SED_SUPPORT	 (SCGCQ00817292)
  - Ventura DA A/R: PCIE error Handling : Device side configurations	  (SCGCQ00817999)    
  - Remove unused PL_USE_PLB_SEGEMENT_1		(SCGCQ00818488)
  - Add new functions for retrieving HW context pointer	 (SCGCQ00818858)  
  - Cleanup of INTRUDER_PORTING	(SCGCQ00819220)
  - Ventura: Update CCR header file and code to latest EDS revision	(SCGCQ00822252)   
  - Ventura: update Cuda header file to latest revision	 (SCGCQ00825826)
  - Ventura SW A/R: Handle SHEX Stall on application errors	(SCGCQ00827432)
  - Ventura: backend PCIe: some bringup changes	(SCGCQ00829039)
  - Ventura DA A/R: Define PCIe error related status codes and log info codes(SCGCQ00829228)
  - Ventura SED support for PIM allowing SED SAScores access to IOA shadow registers (SCGCQ00831248)  
  - Virtual SES SGPIO Support (SCGCQ00832629)
  - Integrate PCIe link events with PCIe Discovery and Device Manager	(SCGCQ00833319)
  - Ventura: backend PCIe: reporting of device link capabilities in PCIe Device Page 0 (SCGCQ00836800)  
  - Initial code to access SED Emulator via POMs and setup SAScore registers (SCGCQ00836918)
  - Ventura: backend PCIe: resolve some NVMe TM TODOs (SCGCQ00839540)
  - Ventura: Enterprise: configure SHEX virtual ports	  (SCGCQ00841697)
  - Ventura Tiger: Poll for Remote SASCore Interrupt	  (SCGCQ00843664)
  - Ventura: PL to provide capability for MR FW to change the IO completion (ReplyDestination  to Host/CPU0/1	  (SCGCQ00846550)
  - Ventura: add some additional register dumping debug code (SCGCQ00852294)
  - Ventura: additional items for diag console debug dump commands	 (SCGCQ00852648)
  - Ventura: Add ring buffer print for RxCtxMgr TimerReached interrupt (SCGCQ00865215) 
  - No release note. PlSim is not a released product.  (SCGCQ00872268)    
  - Additions for Tiger/Styker build	 (SCGCQ00880830)
  - Ventura: backend PCIe: clean up some TODOs	 (SCGCQ00881882)
  - Ventura: backend PCIe: hard reset the PDB cores at PL init time	 (SCGCQ00883464)
  - Tiger/Stryker: Isolate PDB code from Tiger/Stryker builds Part II (SCGCQ00891905)
  - Ventura: backend PCIe: improve robustness of the INTx handler (SCGCQ00896564)
  - Tiger IOP: Add support for the PBAM GPT hardware block(SCGCQ00898142)
  - IOP: Conditionally compile IOA RAM support(SCGCQ00912286)
  - Tiger - Remove firmware workaround for talking to remote SAS Core (SCGCQ00916002)
  - Ventura Build: Add a minimized build to the list of targets	 (SCGCQ00917696)
  - NVMe SCSI Translation updates	(SCGCQ00925607)
  - PL: Ventura-Tiger: SED/Tiger Completion Q allocation(SCGCQ00925758)
  - IOP/PL: Use 128 byte reply message size	 (SCGCQ00927749)
  - IOP/PL: Update additional structures to use OCM PLB Segment 2(SCGCQ00927962)
  - Ventura: backend PCIe: optimize firmware start path for encapsulated requests	(SCGCQ00932934) 
  - Ventura: backend PCIe: handle max payload size mismatch	 (SCGCQ00936258)
  - Ventura/Marlin: Improve TM Code readability	(SCGCQ00937021)
  - Ventura: backend PCIe: handle some additional FxCore exception mid type cases(SCGCQ00937444) 
  - Ventura: Revert the PCIe TM timeout to original TM timeout value(SCGCQ00939494)
  - Ventura: Add CSW registers to pl dbg	(SCGCQ00940256)
  - Ventura B0: backend PCIe: FxCore error handling feature bringup(SCGCQ00941040)
  - PL: Ventura: Add processing of PCIe Topo Change List Add from downstream MPI devices (SCGCQ00942302)  
  - Ventura: Create defines for the Location value for PL_VALIDATE_CALLBACK	 (SCGCQ00948240)
  - Ventura: Revert to old method for FPE frame ownership change	 (SCGCQ00948489)
  - PL: Implement parity checking in some areas	(SCGCQ00950601)
  - Ventura: backend PCIe: NVMe submission queue timeout handling modification	 (SCGCQ00952601) 
  - PL: Initial handling of MPI SAS Device Status Change Event (SCGCQ00953376)
  - Ventura: Eliminate ALADIN interrupt print	(SCGCQ00993798)
  - PL: PCI Config Page support for attached MPI devices (SCGCQ00996165)
  - Ventura: Support for user configurable option to select the PBAM GPIO LED Data polarity	  (SCGCQ00997306)  
  - Ventura: backend PCIe: remove hardcoded Gen2 speed limit (SCGCQ00998522)   
  - PL: Improve MPI IRQ handling and add SCSI IO support (SCGCQ00999444)
  - Tiger: Handle DMA failures during host port link down.	 (SCGCQ01002313)    
  - PL: Handle a second path to a downstream MPI SED(SCGCQ01014773)
  - Tiger: Send FirstDevhandle in SED init message	 (SCGCQ01015370)
  - Ventura PL: Update code to correctly remove both paths upon SED removal	 (SCGCQ01015504)
  - Ventura: backend PCIe: add printing of negotiated link speed/width to diag command	 (SCGCQ01017041)   
  - PL: SED: Add initial support for SMP Passthru (SCGCQ01017119)
  - Ventura PL: MPI Driver must send correct HostPageSize field in IOCInit (SCGCQ01022846) 
  - Ventura: Add Enclosure level and Connector name to PCI device page 0 (SCGCQ01027289)
  - Ventura: Initiate PCal when 3/6 gb SAS link comes up	 (SCGCQ01031980)
  - Ventura IOP+PL: Add support for MPI Passthrough request and reply (SCGCQ01032692 )   
  - Change "BAD IoCount decrement" debug print to standard format (SCGCQ01035202)
  - Ventura Tiger (PL : Implement support for Query Task and Query Task Set to SED Attached SAS/SATA drives(SCGCQ01037212) 
  - Ventura PL: Add basic PCIe R/W error handling to MPI driver	(SCGCQ01037559)
  - Ventura Tiger: Add support for remote SAS/SATA device removal.	(SCGCQ01039132)   
  - Ventura PL: Add SED owned phy table entries	(SCGCQ01042709)
  - Cleanup Host Trace Ouput by zeroing out old entries	(SCGCQ01055035)
  - PL: Support downstream SAS devices when the parent SED goes missing	 (SCGCQ01057643)
  - PL (Tiger : Add support for firmware started fast path IOs to SED attached devices (SCGCQ01058871)  
  - Ventura: Create PLI compliant method for PL to check debug print mask (SCGCQ01063057)
  - Integrate MPI2.6 headers 2.00.44 (SCGCQ01063292)
  - Ventura: Delete AHCI code from codebase	(SCGCQ01071349)
  - Ventura Tiger: Allow TM Target reset to a SSP device to be in scope of an already outstanding target reset to the same device (SCGCQ01073848)
  - Ventura Tiger: Collapse Various PL Firmware Context Flag Bits Into Single Owner Field(SCGCQ01076760)
  - Tiger A0: Add support for PCIe Io Unit Page 0 read(SCGCQ01084789)
  - Ventura/Marlin: backend PCIe: diag command to print device link speeds and widths (SCGCQ01086013)
  - Marlin: Update CCR header file to the latest spec	(SCGCQ01086086)
  - Ventura: backend PCIe: add macro for converting an internal structure pointer to an index (SCGCQ01089514 )   
  - Ventura: backend PCIe: enable/disable new FxCore features at runtime(SCGCQ01092303)
  - Remove IR source code(SCGCQ01107754    )
  - Ventura: backend PCIe: add B0 recognition(SCGCQ01112244)
  - Ventura: add workaround for SCGCQ00887694 to PDB workaround table (SCGCQ01124634)
  - pl: NVMe: NVMe Encapsulated request Force Admin Error Response flag(SCGCQ01130558)
  - NVMe: handful of changes for NVMe SGL support(SCGCQ01134129)
  - Ventura B0: Enable PBAM HW Workaround (CR 46  for Ventura B0(SCGCQ01134375) 
  - Ventura: Set SPL mode in SAS Phy control(SCGCQ01141105)
  - pl: backend PCIe: add compile option for hot reset on PCIe link up (SCGCQ01141218)
  - Ventura: Add fault for unexpected CSW error interrupts	  (SCGCQ01143296)
  - Block JBOD Drive Commands.	(SCGCQ01143396)
  - Ventura: Add build time and date to "pl ver" command(SCGCQ01152140)
  - PL: NVMe Internal header file updates(SCGCQ01162206)
  - pl: NVMe: allow usage of multiple namespace device that supports NSID 1(SCGCQ01163417)
  - Ventura: Auto backplane type detection and configuration support(SCGCQ01172310)
  - PL: Provide makedefs.h in PL Library builds	 (SCGCQ01182555)
  - OEM NVMe backplane detection, PCIe Reset and LED management over I2C(SCGCQ01253925)
  - Ventura/Marlin: backend PCIe: disable PERST# toggle on link down(SCGCQ01262553)
  - Ventura: Validate PortSelected field passed to snooping config function	(SCGCQ01273125)
  - Ventura/Marlin: backend PCIe: NVMe core exception and completion queue handler optimization(SCGCQ01281240 )  
  - Ventura: Defeature using Man page 12 slot info option(SCGCQ01282530)
  - JBOD Personality : NVRAM changes associated with base EPD management changes (SCGCQ01302322)
  - Request for Raid FW to disable battery charger when battery voltage is less than 3V for 2 hours or more.  (SCGCQ01305687) 
  - Create a PL CLI command to send SPICO interrupt	  (SCGCQ01310347)
  - remove devH debug code in DmSMPReadyClear/Set(  (SCGCQ01315972)
  - MR7.3 : Support auto-configuration feature (autopdache  on Ventura (SCGCQ01320083)
  - Check in four XSD files into FW stream, these are used for nvdata migration to CQ.	(SCGCQ01321009)  
  - PL Library Integration 3.250.03.00 (SCGCQ01332072 (SCGCQ01331493)
  - Perc10 update to the HDD/SSD temp. polling (from 5sec to 30sec 	(SCGCQ01335625)
  - Add ARMv5 tool support	 (SCGCQ01344659)
  - [NVRAM] Warning removal 1295 (SCGCQ01373260)
  Making MCTP interrupt context code FIQ safe.	 (SCGCQ01387060)
  - Synchronize time with external enclosures (SCGCQ01421081)
  - Dual SEP support for certain OEM controllers	 (SCGCQ01423790)
  - Integration of PL 03.25.10.00 to 7.2.1 with new SPI library	 (SCGCQ01424789)
  - PI Enablement	 (SCGCQ01425012)
  - Add support in FW for new LL hung connection timer/controls in HW (SCGCQ00105465)
  - EDFB: if EDFB settings change for an expander phy, update the attached device	(SCGCQ00120483)
  - Gen3: TBM - Add UART debug commands	(SCGCQ00127511)
  - Firmware build needs to link pre-built PL library, instead of compiling it with the rest of firmware (SCGCQ00134475)
  - Gen3 PwrMgmt: Add "Presence Detect" capability for direct-attached phys  (SCGCQ00135543)
  - Gen3 PwrMgmt: Add PL support for TxDMA, RxDMA, RxEEDP light sleep/deep sleep/shutdown modes	  (SCGCQ00136933)
  - Gen3 PwrMgmt: Implement UART interface to configure Tx/Rx DMA and RxEEDP sleep modes and sleep timers.	  (SCGCQ00136940)
  - Detroit EDS 1.1 header updates (new register/bits (SCGCQ00144625)
  - Add PLI control request for PauseHostRequest Cuda bit on/off(SCGCQ00144626)
  - Update FPE manage CCA handling to account for completions being routed to FW (SCGCQ00145551 )   
					
  - Update Qmanger State register to latest register format	 (SCGCQ00146599)
  - TBM: Update ForceFlush handling (SCGCQ00149047)
  - FPE: Dev Test Customization	(SCGCQ00151752)
  - SAS-3 Remove Diagnostic Checkpoint Lock and Pause Features	 (SCGCQ00152338)    
  - Gen3: PL Light(SCGCQ00152450)
  - Control Q disabling needs to pause Cuda as well	(SCGCQ00152670)
  - RxBuffer and TxBuffer has grown for gen3 (SCGCQ00153291)
  - Change the mid validation code in PL to filter out mid 1 as well (SCGCQ00156042)
  - FPE - prevent auto reenable of FP on TM completion.	(SCGCQ00156594)
  - Update colt register definition	(SCGCQ00157362)
  - Add back the 250ms delay at end of TM completing before we really complete	  (SCGCQ00159015) 
  - pl: Update Starfish register definition	(SCGCQ00160016) 
  - Update MemCfg utility for SAS3FW compatability (SCGCQ00160081)
  - FPGA: FW Update for Colt Bitstream R24(SCGCQ00160234)
  - FPE: direct cleanup of Fast Path Exception Q appears needed	 (SCGCQ00160401)
  - FPE: add pli control requests to adjust the cuda auto trace levels(SCGCQ00160522 )   
  - FPE - Implement Enable Qdepth Pending functionality for Cuda (SCGCQ00162734)
  - Round 3 gen2 HW WA removal	 (SCGCQ00163434)
  - PL: add FPGA workaround for EDFB DMA Groups	 (SCGCQ00166550)
  - TM: Remove all references to FWNonAuto bit from SATA code(SCGCQ00173988)  
  - TM: SATA: plSataTaskMgmt.c cleanup	 (SCGCQ00173995)
  - Remove workaround code for [SAS2Core] 1443	 (SCGCQ00174732)
  - Remove [SAS2Core] 1682	  (SCGCQ00180293)
  - Remove [SAS2Core] 1411	  (SCGCQ00180304)
  - Remove "hw workaround" SCGCQ00132812  (SCGCQ00180306)
  - Get presence detect working	 (SCGCQ00187448)
  - PL: change Reason reported in SAS Expander Page 1 PhyInfo field	  (SCGCQ00187475)
  - Add R26 colt support (SCGCQ00194012)
  - Gen3: PwrMgmt - Tx/Rx/EEDP Memory needs WA due to Manufacturing Design Alert (SCGCQ00204182)
  - Porting up Gen2 changes from Phase 11 for ISTWI and Enclosure Management CSETs	  (SCGCQ00208724) 
  - Print out a warning when no valid context is selected	 (SCGCQ00209049 )   
  - TxCtxMgr Interrupt handling cleanup	 (SCGCQ00209353)
  - Check in new serdes settings (v2.13   (SCGCQ00218030)
  - Gen 3 : Parity bits checking for the IOA(Detroit  Core	  (SCGCQ00221731 )   
  - TxFM and CtrlQ code cleanup and debug improvements	  (SCGCQ00222848)
  - Invader A0: Target Mode print optimization	(SCGCQ00223545)
  - Allow the frequency deviation of the down spread SSC profile to meet the sas spec (SCGCQ00225376)   
  - Update TM Hw context memory structure for gen3	  (SCGCQ00227727)
  - Active cable support part three	(SCGCQ00227767)
  - Customer requests common SAS3 header files to also include SAS2 only information (SCGCQ00229951)  
  - Change default NVDATA value for MaxCmds	(SCGCQ00230073)
  - Snapshot buffer updates for Gen3(SCGCQ00231500)
  - EDFB function to turn STP AA bit on / off	  (SCGCQ00246383)
  - Active Cable Management: Limit sata link rate based on cable's link rate (SCGCQ00251851)  
  - PL HW WA matrix updates	 (SCGCQ00262832)
  - PL: Implement a vendor specific PLI control request	(SCGCQ00269392)
  - pl pci: Enumeration and Configuration (SCGCQ00308793)
  - [Dauntless]: 'Stang HW header file(SCGCQ00310157)
  - Hardware changes from Invader for Boot(SCGCQ00338455)
  - Various NVMe related changes(SCGCQ00341755)
  - PL: NVMe Task Management(SCGCQ00371626)
  - Support for new config pages PCIe IO Unit Page0,1, PCIe device pages 0,1 described in MPI 2.6 specification(SCGCQ00377454)
  - NVMe firmware-only mode(SCGCQ00378032)
  - Use dedicated Stang NVMe chain area(SCGCQ00391063)    
  - Added handlers for PCIe errors(SCGCQ00400046)
  - Modify PLB to PCIe Address lookup to support 32 bit PLB addresses(SCGCQ00402720)
  - Dauntless: Implement PLI control request for MR to set snoop regions in stang and PDB.(SCGCQ00412920) 
  - Add SOP and PQI header files(SCGCQ00423525) 
  - Disable a set of Invader workarounds that were fixed in Dauntless Colt core(SCGCQ00437137)  
  - SOP Initialization Cleanup(SCGCQ00442840)
  - Add support for PCIe prefetchable memory BARs(SCGCQ00449047)
  - Change SOP Init to start at discovery(SCGCQ00468966)
  - Additional (PCIe - PDB  debug data through pl dbg command(SCGCQ00479680 )   
  - SAS3.5FW: Colt changes: Dma Engine Changes(SCGCQ00518157)
  - SAS3.5FW: Colthw.h changes from Invader to Dauntless(SCGCQ00522283)
  - Ventura: IOA – Impala IO Accelerator Cuda Block Bring Up(SCGCQ00522530)
	  (SA(S3.5FW: Colt changes: RxEEDP registers(SCGCQ00530498)
  - SAS3.5FW: SAS Core changes: TxFrameMgr Register Differences(SCGCQ00531028)
  - Create RaptorHw.h SAS Core register file(SCGCQ00572620)
  - (VENTURA BUILD  Add sufficient capabilities to allow firmware to boot to iopSched(  with NVDATA(SCGCQ00599359)
  - Ventura: Port PPC FAULT routines to ARM(SCGCQ00606223)
  - Modify PLI interface to take SasCoreNum parameter(SCGCQ00630403)    
  - Add HwNumPhysPerSasCore, HwNumPhysPerChip and FirstDevHandle to PL_INFO(SCGCQ00639789)
  - Enterprise: update header file for EDS 1.2(SCGCQ00642848)
  - Backend PCIe: remove some console prints(SCGCQ00651365)
  - PL: Add sas core support to SATA according to the newly modified functions and structur(SCGCQ00653721)
  - plSim: Phase 0.1(SCGCQ00663151)
  - Enterprise: extra start of day changes(SCGCQ00664344)  
  - Removed specified A0/B0 Invader WAs(SCGCQ00667023)
  - Ventura: Backend PCI - generate PCI reset from TM(SCGCQ00674370)    
  - Removed remnants of old HW Workarounds(SCGCQ00680168)
  - Ventura: Enable DCR access macros for ARM(SCGCQ00682711)
  - Add multiple SAS core support for Diag Snapshot feature(SCGCQ00684391)    
  - Ventura: backend PCIe: devhandle map modifications(SCGCQ00690205)    
  - SAS3.5: Implement Firmware Control bit for Unconfirmed Response in FwCompQIoPathCtrl(SCGCQ00706889)
  - Intruder: Add muticore support for Target Mode Abort All command Buffers functionaility(SCGCQ00711462)  
  - Convert RxFrameManager interrupt handler to use all bitmasks(SCGCQ00715074)
  - PL: Final PL_MULTI_SAS_WORK_NEEDED cleanup(SCGCQ00716812)
  - Intruder PL: enable C2 Decrement(SCGCQ00716814)
  - PL NVMe: Use internally saved NSIDs(SCGCQ00723592)
  - Ventura: Create CCI-400 Header File(SCGCQ00731687)
  - Ventura: Implement Build Optimizations Recommended by ARM(SCGCQ00759482 )   
  - Added Prints/Debug Info on 0x6230 Fault(SCGCQ00762305 )   
  - Ventura: Implement PCIe Discovery Event Replay(SCGCQ00771839)
  - Fix a PL Internal Structure(SCGCQ00784564)
  - Ventura: Remove PL private files from the IT build(SCGCQ00785195) 
  - Improve the PL_ASSERT macro usage.(SCGCQ00804858)
  - Cleanup and changes to SASCore register pointer initialization(SCGCQ00813952)  
  - Ventura DA A/R: PCIe Error handling in NVMe init path(SCGCQ00821998)
- Aladin Core: Functionize Aladin Reset Code in PL (Start of Day(SCGCQ00823048)
  - Remove remaining usages of plGetHwContext( 	(SCGCQ00824293)
  - Add NumberOfSEDs and NumberofSEDMids to mfg page 9(SCGCQ00831065)
  - Ventura: backend PCIe: hide backend PCIe devices from virtual functions (part 1(SCGCQ00854613)  
  - Ventura: Add SAS exception queue contents to debug register dump(SCGCQ00890978)
  - Remove Dauntless Defines: PL - SAS core specific and miscellaneous changes.(SCGCQ00905985)
  - Tiger/Stryker: CSR init(SCGCQ00907988)
  - Add support for R37 SAScore version(SCGCQ00928920)
  - PL: Update plPhySetPowerMode(  for Ventura(SCGCQ00936306)
  - PL: Handle SAS Enclosure Change Event from downstream MPI device(SCGCQ00952961)
  - Tiger PL & IOP: First round of implementing SAS core memory translation(SCGCQ01000544)
  - Ventura Tiger support added to configure hardware to send IO to Tiger device(SCGCQ01006667 )   
  - Ventura: Port optical support to ventura(SCGCQ01019664)
  - Ventura: FPE: add FxCore enqueue counter to FPE stats dump(SCGCQ01035197)
  - Ventura/Marlin: backend PCIe: allow assignment of additional memory space to backend PCIe devices(SCGCQ01040918) 
  - Ventura PL: Populate the Timestamp field of IOCInit requests sent to SEDs(SCGCQ01079240)
  - Ventura/Marlin: backend PCIe: negotiated speed/width fields in PCIe Device Page 0(SCGCQ01089506)    
  - Backend PCIe: add some additional registers to a backend PCIe related header file(SCGCQ01107259 )   
  - PL: Implement support for SAS Device Discovery Error Event(SCGCQ01233843)
  - Disable T10 Protection Information support(SCGCQ01325001)
  - Change PL baseline from 03.250.04.00 to 03.250.08.00(SCGCQ01363971)    
  - Updating OEM enumeration PL Phase_4.0 - 04.15.00.00 MR PL(SCGCQ01366959 )   
  - Just enable the Megamon SBR reload command.(SCGCQ01371967)
	- (SCGCQ01402213)
	- FW added supportOOBCtrlFwDownload to indicate support.  currently disabled)(SCGCQ01420786 )
  - SAS2FW: Need method to set Sentinel Interrupt Coalescing values(SCGCQ00034638)
  - Update pathway analysis for 12G speeds(SCGCQ00128450)
  - Improve TM performance and debug via a per device TM Queue(SCGCQ00130621)
  - Rearrange TM context area bits to accomodate Gen2 TM enhancements(SCGCQ00143171)
  - Convert the SAS IOUnit control request for enable/disable of fast path to use PLI control request when going from IOP to PL(SCGCQ00145206 )   
  - SAS3 Update to the SAS Core Colt's RX_CTX_DMA_DIAG struct(SCGCQ00148678)
  - Code cleanup and bug fixes for adding entries to Colt's TxDMAQ(SCGCQ00149115)
  - pl: Detect if a device supports Download Microcode DMA(SCGCQ00152237)
  - Fix the random sgl read problem(SCGCQ00152697)    
  - FPE: turn off FPE for SATA(SCGCQ00160887)
  - Remove PL_SAS2HW_RXDMA_WRAP_WORKAROUND code(SCGCQ00163618 )   
  - (Invader  BT 1680 removal in IOP and PL(SCGCQ00170554)
  - Colt 1.4 EDS updates(SCGCQ00170626)
  - Dump message frame for the mid when x5842 fault is hit(SCGCQ00176343)
  - Remove [SAS2Core]1754(SCGCQ00180249)
  - CLI menus should be dynamically spaced(SCGCQ00205520)
  - update some back channel training register definitions(SCGCQ00208312)
  - Add an temporary workaround to dump the starfish registers(SCGCQ00210503)
  - Colt EDS 1.8 register updates(SCGCQ00223522  )  
  - Disable MisMatch FM for b0(SCGCQ00243436)
  - Trace Buffer timestamping ability for host drivers via a SCSI IO(SCGCQ00258646)
  - pl: NVMe Stang Initialization(SCGCQ00336344)
  - NVMe glue code(SCGCQ00357921)
  - Added command to show PCIe capabilities list for an endpoint.(SCGCQ00365545 )   
  - Added code to dump IOA registers(SCGCQ00383645)
  - Update existing backend PCIe events to MPI-2.6 format(SCGCQ00391416)
  - Added structures required for FW R/W IO Path (including IO Breakup(SCGCQ00402757)   
  - Update to latest changes for PCI fastpath engine(SCGCQ00434773)
  - MPI 2.6 Rev. B Feature: Add NVMe SGL support. Add Capabilities field to PCIe Device Page 2.(SCGCQ00443383)  
  - Added "pl pci ahcislot" to print AHCI slot information(SCGCQ00449096)
  - NVMe: Check in init workarounds for early NVMe device(SCGCQ00450246)
  - Additional encapsulated path items(SCGCQ00469629)
  - Create new build environment for future product(SCGCQ00477789)
  - Update PQI and SOP to the latest revisions(SCGCQ00502916)
  - Update PL for TxDMA Context Manager Register Changes in SAS Core from Invader(SCGCQ00518713)
  - NVMe: task management, part 2(SCGCQ00525641)
  - NVMe: debug command items(SCGCQ00563923)
  - PL: Update power management code to account for multiple SAS cores(SCGCQ00606792) 
  - Create suitable conversion functions between chipRelativePhyNum , coreRelativePhyNum and SasCoreNum(SCGCQ00641789)
  - Replace direct POM accesses that occur in generic PCI code (non-protocol  with safe accessor functions.(SCGCQ00642671)  
  - Intruder: Updates for FPGA(SCGCQ00665826)
  - Update plEDFB.c to be multiple SASCore compatible(SCGCQ00685110)
  - Intruder: Add Multi SAS core support to Target DMA passthrough complete handler(SCGCQ00712889)
  - (Target Only  Hw Initiator and VID Response Table is not common to different cores. So make multicore changes accordingly.	(SCGCQ00718699)    
  - Ventura: Enterprise: return unique status for CRS on config space access(SCGCQ00761092)
  - Ventura: Add support for PCIe Topo Change List Event PORT_CHANGED status(SCGCQ00771836)
  - Ventura: Add Control Q Fifo parameters to hardware parameters(SCGCQ00789508)
  - Ventura: Update internal NVMe file headers(SCGCQ00895664)
  - IOP: Tiger/Stryker convert to use ARM Vectored Interrupt Controller(SCGCQ00917849)
					)
  - Delay host notification of NVMe drive until after the complete NVMe Initialization.(SCGCQ00926709)  
  - PL: Add handling of inbound SAS Topology Change List Events(SCGCQ00939823)
  - Tiger: Handle Host Link Down-Up(SCGCQ00997588)
  - User must be warned when they create a VD across the front backplane and enclosures behind the switch[H745P MX](SCGCQ01291050)
  - MR-7.2 INTEL NVME:Can't Start Patrol Read Under HII/Storcli/LSA(SCGCQ01342927)
  - Cache Snooping Should Not Be Disabled after L2 Flush as OCM flush may still be active.(SCGCQ01345679 )   
  - Allow Host IOs while pinned cache flush is in progress during run time(SCGCQ01350527)
  - Warning removal 128(SCGCQ01364923)
  - Graceful Handling of faulty enclosures, not providing config pages.(SCGCQ01375949)
  - BST script for JBOD personality(SCGCQ01389661)
  - Aero release support(SCGCQ01392706)
  - MPI Target Assist Request changes(SCGCQ00088392 )   
  - FPGA: Update interrupt masks.(SCGCQ00095007)
  - add print for 3rd possible case occuring on plFpeChangeOwnertoPL((SCGCQ00147319)  
  - FPE: Cuda Pend Queue Cleanup during TM(SCGCQ00160611)
  - Round 1: Remove unused HW workarounds (old gen2 wa's(SCGCQ00161805)
  - Add TxDMA/Ctx cleanup early on in TM start. Keep the existing cleanup at end to handle any xfer rdy that came in last second(SCGCQ00162474)    
  - Colt EDS 1.5 updates(SCGCQ00187684)    
  - Add SASCore->FPE completion Q dump to "pl dbg all"(SCGCQ00228221)    
  - pl pci: NVMe Initialization(SCGCQ00276500)
  - pl: NVMe SCSI IO Path(SCGCQ00308842)
  - (IOA  Modify pliTBMAddEntry(  so that it automatically selects port via processor ID(SCGCQ00350777 )   
  - [Dauntless]: SGL Translation - IEEE-64 to NVMe (1.1 compliant(SCGCQ00362775)
  - Firmware Read/Write IO Path - Base Functionality (Error paths(SCGCQ00411229)
  - Add SOP/PQI initialization workarounds for SOP drive(SCGCQ00449049    
  - Updated FxCore blocks to match new hardware(SCGCQ00522531)    
  - Intruder, Dauntless & Ventura: Update PLI control request SAScore request for multi core (plmsg.c(SCGCQ00684425 )  
  -(SCGCQ00758323 )
  - Ventura: Update internal structures(SCGCQ00898193 )   
  - Ventura: Jitter changes(SCGCQ01212876)   
  - Adapting to new PL baseline Phase_4.0 - 04.25.00.00(SCGCQ01380072)    
  - Port Layer error handling - cleanup/improve/optimize(SCGCQ00126458)   
  - FPGA: Fw needs to wait for PLL ready before switching clock domain(SCGCQ00145565)
  - FPE: Prevent Zero IO Count state advancement when CCA is disabled in NVData(SCGCQ00167140)   
  - update serdes values(SCGCQ00186665)
  - NVMe device asynchronous event handling(SCGCQ00334789)
  - [Dauntless]: Initial file checkin (SGL translation(SCGCQ00342709)
  - Changes to internally generated commands to AHCI devices(SCGCQ00376480  )
  - Discovery and Device Manager changes for need to start init process earlier and setup WWID for devices(SCGCQ00455897)  
  - Diag console command for dumping backend PCIe enumeration structures(SCGCQ00499868)
  - Enterprise: error message counter configuration(SCGCQ00552431)
  - Ventura: Update PL Light to use CPU Number(SCGCQ00760481  )  
  - Add PIM/POM table entries for Tiger/Styker(SCGCQ00910622 )   
  - This ER created for refactoring two Invader CSETs on a new Ventura DM interface(SCGCQ01291836 )
 - Added NVME passthrough support for MR stack(SCGCQ01391416)
 - enable OOB FW download for MR alone.(SCGCQ01455694  )
  - Integrate MR PL/SCS Libs: SASFW_Ventura_Phase_4.0 - 04.25.04.00 MR PL-SCS Libs(SCGCQ01462721 ) 
  - New debug commands(SCGCQ00376574  )  
  - Add Support for Single Image Cache Offload.(SCGCQ01309432)


Version 50.2.1-0601 - Moderate Impact/Low Probability of Occurrence
-------------------
BIOS:  7.02.03.1_4.17.08.00_0x07020401
UEFI Driver: 0x07020401
HII:  07.02.05.01
MR FW:  5.020.00-1045
PACKAGE:  50.2.1-0601
Fixes:
- R0 HDD WB-Switching between cases of IO going to cache and bypassing cache happens frequently on certain profiles (SCGCQ01138581)
- Multipath SAL script failed (SCGCQ01177445)
- manufacturing info for enclosure is showing zeros under SMP passthru menu in Storelib. (SCGCQ01188954)
- ESXi 6.0 U2 or ESXi 6.5 hangs during reboot (SCGCQ01214236)
- Progress time for CC/BGI is inconsistent with Rebuild/Copyback (SCGCQ01220611)
- Controller hangs during OCR (SCGCQ0122920)5
- controller hangs (cannot get into debugger) after running i/o for a few hours (SCGCQ01229276)
- MR7.1 UEFI BIOS Is Not Shown for OEM controller (SCGCQ01229284)
- CLI reports "Support LargeIOSupport" as No (SCGCQ01229311)
- Critical Message = " Error restoring offload cache " during MedusaIO running to R50 with power loss (SCGCQ01229975)
- Change OEM_MERCURY Check to IoPathFlagOemMercury (SCGCQ01230006)
- The QDChanged flag is never reverted back to 0 (SCGCQ01230078)
- Next LD is not set while PD rebuild is in progress and the current LD is deleted. (SCGCQ01231043)
- Fix to fail back pre read call back graciously when there are unrecoverable errors are hit (SCGCQ01231653)
- During learn cycle, the battery does not discharge. (SCGCQ01232276)
- NVMe: DC found when running Chaos on R5-WT-DIO-NORA with IO/Buffer size of 16kb or less (SCGCQ01232376)
- Drive Firmware Upgrade fails while running IO's on a JBOD drive. (SCGCQ01232733)
- Unable to see any option for Crypto erase in HII for any HDD/SSD ISE drive (SCGCQ01233384)
- Assertion failure in ../../mros/mem.c at line 617: mb->tag==tag after update to new ROP 270 and reboot (SCGCQ01235357)
- Performance Reduction seen in BST (SCGCQ01235742)
- Defect port from mainline (SCGCQ01235761)
- Max NVMe drive support shows as 8 for MR 7.1 for NVMe profile (SCGCQ01236604)
- some SATA ISE drives are not displaying as ISE capable (SCGCQ01237004)
- NVMe 9440-8i Rebuild does not start on 2 drive R1-Win7 (SCGCQ01237009)
- Locate PD does not work with SGPIO backplane (no blinking LED) (SCGCQ01237036)
- Loss of access to PI VD causes crash (SCGCQ01237965)
- OOB discovery fails (SCGCQ01238858)
- PL rejecting cmds due to invalid values in structure members (SCGCQ01240309)
- Multiple VDs created over idrac with racadm fails (SCGCQ01241098)
- Print DirtyCache status (GPIOA6 )during controller Initialization (SCGCQ01241691)
- Set mdts value to 128KB in case any drives has higher mdts value (SCGCQ01242011)
- DC observed on R10 VD, post importing the foreign configuration after Megamon triggered OCR (SCGCQ01242067)
- Redundant path broken for PD 00(e0x40/s0) message for OS Disk when removing a known bad SATA SSD from a different slot. (SCGCQ01242091)
- Excess prints slows controllers response to host commands. (SCGCQ01242470)
- C10 - FW crashing at "Assertion failure in ../../hw/main.c at line 606: 0" during looped cache offload test (SCGCQ01244311)
- Set mdts value to 128KB in case any drives has higher mdts value (SCGCQ01245535)
- Drives not getting discovered after OCR/Reboot in iMR controller with 295 Fw package. (SCGCQ01247494)
- OOB Storage Configuration - Unable to create 3 x 14PD, 42 drive simple RAID10 VD. (SCGCQ01247647)
- PRequest message shows numerous times in log (SCGCQ01249133)
- Fatal firmware error: Line 934 in ../../cpu/arm/exceptions.c while importing foreign config with pinned cache (SCGCQ01249809)
- Kill adapter found while running CC on VD's with media errors (SCGCQ01249815)
- Continuous Prints observed during Reconstruction operation. (SCGCQ01249820)
- Inconsistencies in foreign configuration import when cache is pinned. (SCGCQ01249966)
- Initiatlize partition map during PD Replace within LD (SCGCQ01250193)
- GetAllLDAllowedOperation call in Storelib is not returning Allowed operations when some LDs are deleted (SCGCQ01250559)
- iMR cable pull IO Drop on VDs (SCGCQ01250688)
- Hibernate Feature in Windows 7 doesn't work properly, if IO's are running in background (SCGCQ01251505)
- Issue - OLTP performance is less than Intruder by 10-20%. (SCGCQ01252558)
- Hitting Kill adapter for importing Foreign configuration and query controller information( IO was not running ). (SCGCQ01253096)
- FW Kill Adapter observed while performing the RLM operation on OS VD from R1 to R0 (SCGCQ01253798)
- Life Cycle 3.00.00 Build 24: Redundant VD shows as FAILED State, when its actually Degraded. SCGCQ01253921
- Controller enters MonTask during Rebuild on PI enabled VD (SCGCQ01255170)
- Profile ID update Event doesn't reflect prior profile ID (SCGCQ01255917)
- CC is not correcting DIFF errors after reporting them as corrected. (SCGCQ01256210)
-  WG: In case of preview, FW should not return "MFI_STAT_CTRL_RESET_REQUIRED" status code : MR Ventura (SCGCQ01256323)
- FW breaks into montask with fusion MU error - data descriptor overflow error.. (SCGCQ01256286)
- FW hit "C0:MptIssueCmd: ERROR!!! Unknown command x0 in Rdm=x7fb95780" upon booting up (SCGCQ01259277)
- SBL bus init leads to system hang and BST failure (SCGCQ01259726)
- RSOD been observed after disabling Data protection on PI enabled VD (SCGCQ01260419)
- iMR controller missing one NVMe drive when reboot (SCGCQ01260754)
-: ddf while remove 2nd pd in 2DR1,4DR10 for pinned cache (SCGCQ01261386)
- Improvements for offload/restore reliability (SCGCQ01262608)
- There is mprintf error (printing a message) that is causing this TLB error during error recovery for sanitize. (SCGCQ01263180)
- Create slot id to pd mapping for NVMe drives (SCGCQ01263802)
- Storcclif start diag DMA Test failed (SCGCQ01264038)
- Disable BIOS flag in Megamon ( dbgflag biosDisable 1 ) successfully set but it is not actually working (SCGCQ01264139)
- After performing Clear/PD erase on SATA SSDs system hangs (PL Fault) (SCGCQ01264210)

Version 50.0.1-0381-1 - High Impact/High Probability of Occurrence
-------------------
BIOS:  7.00.09.0_4.17.08.00_0x07001600
UEFI Driver: 0x07001600
HII:  07.00.38.01
MR FW:  5.001.00-1025
PACKAGE=50.0.1-0381

- Fixed a package issue that would attempt to update unsupported devices.

Version 50.0.1-0381 - High Impact/High Probability of Occurrence
-------------------
BIOS:  7.00.09.0_4.17.08.00_0x07001600
UEFI Driver: 0x07001600
HII:  07.00.38.01
MR FW:  5.001.00-1025
PACKAGE=50.0.1-0381

- Fixed an issue where the controller could hang while importing a commissioned hot spare drive. (SCGCQ01393703)

Enhancement(s)
- Implemented a workaround for a device attached between the root complex and the controller; in order to addresses the issue of the controller going to Gen 1 speed during D3 Hot state transition due to an issue with IDT timer. (SCGCQ01401585)


Version 50.0.0-0374-1 - Moderate Impact/Low Probability of Occurrence
-------------------
BIOS:  7.00.09.0_4.17.08.00_0x07001600
UEFI Driver: 0x07001600
HII:  07.00.38.01
MR FW:  5.001.01-0805

- Removed support for out-of-band updating method.


Version 50.0.0-0374 - New Function Only/No fixes
-------------------
BIOS:  7.00.09.0_4.17.08.00_0x07001600
UEFI Driver: 0x07001600
HII:  07.00.38.01
MR FW:  5.001.00-0805





Lenovo Data Center Group Linux OS Support Home Page
linux.lenovo.com

© 2018-2022 Lenovo. All rights reserved

ThinkSystem RAID and ServeRAID M Series SAS/SATA Controller Driver for SLES 12 (For Sles)



ThinkSystem RAID and ServeRAID M Series SAS/SATA Controller Driver for Linux

This product supports [SLES 12.4,SLES 12.5]

Adapters Supported:
	ThinkSystem RAID 530-8i PCIe 12Gb Adapter  (7Y37A01082)
	ThinkSystem RAID 530-4i Flex Adapter       (7M17A03932)
	ThinkSystem RAID 530-4i Flex Adapter       (7M27A03918)
	ThinkSystem RAID 530-8i Dense Adapter      (SD530 RAID)
	ThinkSystem RAID 530-16i PCIe 12Gb Adapter (4Y37A09727)
	ThinkSystem RAID 730-8i 1GB Cache PCIe 12Gb Adapter  (7Y37A01083)
	ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter  (4Y37A09722)
	ThinkSystem RAID 930-8i 2GB Flash PCIe 12Gb Adapter  (7Y37A01084)
	ThinkSystem RAID 930-16i 4GB Flash PCIe 12Gb Adapter (7Y37A01085)
	ThinkSystem RAID 930-24i 4GB Flash PCIe 12Gb Adapter (7Y37A01086)
	ThinkSystem RAID 930-8e 4GB Flash PCIe 12Gb Adapter  (7Y37A01087)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M17A03933)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M27A03917)
	ThinkSystem  RAID 930-16i 8GB Flash PCIe 12Gb Adapter(4Y37A09721)
	ThinkSystem RAID 940-8e 4GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-8i 4GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-8i 8GB Flash PCIe Gen4 12Gb Adapter
	ThinkSystem RAID 940-16i 4GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-32i 8GB Flash PCIe Gen4 12Gb Adapter	
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Internal Adapter
	ServeRAID M1210 SAS/SATA Controller    (00JY194)
	ServeRAID M1215 SAS/SATA Controller    (46C9114)
	LSI SAS3004 RAID                       (NA-SAS3004-B)
	LSI SAS3004 RAID                       (NA-SAS3004-N)
	ServeRAID M5210 SAS/SATA Controller    (46C9110)
	ServeRAID M5225-2GB SAS/SATA Controller(00AE938)
	ServeRAID M5215 with 2GB Flash Enablement Flex System x240 M5   (00JX142)
	ServeRAID M5210e SAS/SATA Controller   (46C9117CTO)
	ServeRAID M5120 SAS/SATA Controller    (81Y4478)
	IBM Flex System Storage Expansion Node (68Y8588)
	ServeRAID M5115 SAS/SATA Controller for Flex System  (90Y4390)
	ServeRAID M5100 Series IBM Flex System Flash Kit for X6 (44T1178)


NOTE TO SERVICE - Reference RETAIN #N/A

07.720.04.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.20

Defects:
-Disable "shared host_tagset" feature.(DCSG01107335 (Port Of Defect DCSG01111551))
-Fix race condition due to concurrent access of ISR from multiple contexts..(DCSG01032071 (Port Of Defect DCSG01038495))
-Use managed vectors API/s for IRQ allocation and affinity for >=5.0 and >=RHEL8.2 kernels..(DCSG01060650 (Port Of Defect DCSG01065135))
-megaraid_sas returns DID_NO_CONNECT for an existing LUN.(DCSG01090218 (Port Of Defect DCSG01091958))

EnhancementRequests:
-DCSG01082446


07.719.03.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.19

Defects:
-Fix race condition due to concurrent access of ISR from multiple contexts.(DCSG01032071)


07.717.02.00-2 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.17

Defects:
-One VD deletion leads to IO blocked to different VD forever.(DCSG00948232 (Port Of Defect DCSG00951388))

EnhancementRequests:
-MR7.17: Driver module signing for RHEL and SUSE.(DCSG00418428)
-Block the IO on Deleted VDs derived from Raid Map update.(DCSG00342297)
-MR7.17: Improve error handling at multiple places in driver.(DCSG00368931)
-MR7.16: Add RHEL7.9 GA support.(DCSG00382600)
-MR7.17: RHEL8.3 GA support.(DCSG00418201)
-Xenserver 8.2 LTSR support.(DCSG00361050)

07.715.03.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.15

Defects:
-MR7.15: silence warnings of IO request frames memory allocation failure.(DCSG00243681)
-MR_7.15: 7.15 ROP os readme file accordance with os support list.(DCSG00249459)
-[9361-8i + MR6.14] (Internal BRCM) Controller Run into Fatal Error Stop at Critical State when run fio to reproduce issue in(DCSG00079487).(DCSG00129711)
-Linux_Drv_BST: Update AutoBST script to stop Chaos IOs before deleting FS and other fixes.(DCSG00134557)
-MR 7.14 Linux driver Read-Me file needs some corrections..(DCSG00070005)
-MR_7.14: Linux driver OS_Support_list needs an update..(DCSG00115285)
-MR7.14: Driver is using undefined macro MFI_BIG_ENDIAN for isEPD bit field.(DCSG00137916)
-Limit max device queue_depth to controller queue_depth.(DCSG00059412 (Port Of Defect DCSG00082448))

EnhancementRequests:
-Modify bst_linux.py script to load RHEL7.7 binary.(DCSG00130098)
-MR7.15: RHEL8.2 GA OS Support.(DCSG00167212)
-update dkms.conf file for UBUNTU20.04.(DCSG00080086)
-Remove NVME hole detection algorithm.(DCSG00076490)
-Add RHEL7.8 GA Support.(DCSG00129747)
-MR7.15: SLES15SP2 GM Support.(DCSG00259047)
-Citrix Hypervisor 8.1 GA support.(DCSG00062914)
-BST scripts optimization.(DCSG00073579)
-Source RPM support for RHEL8.2 and UBUNTU20.04 pre-GA OS.(DCSG00079575 (Port Of EnhancementRequest DCSG00081340))


07.713.02.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.13
Defects:
-Use RAID map for Tape devices even if FW supports JBOD sequence map.(DCSG00055167)
-Add NULL check for RAID map pointer in non RW LDIO path and fix coverity reported issues.(DCSG00033292)
-Code review found defect.(DCSG00058719)
-Improper error print message for non-secure AERO adapters.(DCSG00045253 (Port Of Defect DCSG00054761)

EnhancementRequests:
-Unique names to MSIx vectors.(DCSG00025922)
-Call kernel panic upon receive of IO with holes for NVME devices.(DCSG00049785)
-Add binary support for RHEL8.1.(DCSG00049836)
-MR7.13 : SLES12-SP5 GM Support.(DCSG00055090)
-Source RPMs shall be signed with GPG public-private key.(DCSG00056767)
-Source RPMs shall be signed with GPG public-private key.(DCSG00054345)
-Add driver support for "scsi_status" propagation to application.(DCSG00041807)
-MR Linux Driver 7.13 : Driver needs to issue all NonRW IOs to SES/vSES devices as LDIOs.(DCSG00041449)
-Use Block layer API to check SCSI device in-flight IO request.(DCSG00057168)


07.712.02.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.12

Defects:
-Remove incorrect print of Performance mode.(DCSG00002462)
-Improper error print message for non-secure AERO adapters.(DCSG00045253)
-MR7.11 Linux: Controller hangs on the second OCR.(DCSG00012579 (Port Of Defect DCSG00016290)

EnhancementRequests:
-Update queue_depth of sas and NVMe device.(DCSG00007172)
-Port upstream code to MR7.12 in-house code.(DCSG00005496)
-Remove CPU arch check to decide performance mode and rework PCI link speed detection logic.(DCSG00002646)
-Add transition_to_ready retry logic in resume path.(DCSG00008028)
-RHEL 7.7 Support for MR 7.12.(DCSG00020730)
-(DCSG00012782)
-Remove code for older unsupported kernels.(DCSG00002458)
-.(DCSG00002460)
-(DCSG00017314)
-.(Change sdev queue depth max vs optimal)


07.710.06.00 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.10

Defects (20)
 - Add retpoline support in source rpm and fix compilation error in sles15sp1 (SCGCQ02079110)
 - (Supported (Sea((SA(S38xx) PCI IDs. (SCGCQ01942752)
 - MR7.10: Driver logs wrong message about adapter's DMA mask (SCGCQ02012089)
 - Addressed few code review defects/comments on hybrid interrupts implementation. (SCGCQ02057600)
 - Remove support for (Sea(38xx) PCI IDs in MR driver (SCGCQ01913282)
 - MR_7.9: Linux driver fails to reboot the system when controller is in dead. (SCGCQ01936787)
 - Fix deadlock in few DCMDs timeout path due to re-acquiring of "reset_mutex" lock (SCGCQ02044603)
 - (Set VirtualDiskTgtId and devHandle appropriately when JBOD seuqence map is supported by firmware but disabled at driver devel (SCGCQ02080583)
 - MR7.9: Restrict hardware workaround for PCI register read retries for Aero/(Sea PCI IDs Only (SCGCQ01977849)
 - MR7.9, Linux driver: On PowerPC, calling disable_irq_nosync from IRQ context does not work as expected (SCGCQ01984754)
 - MR7.10_ARM:Assertion failure seen in firmware during boot on cavium ARM server (SCGCQ02035288)
 - Fixed PCI link speed detection and modified few printk debug levels (SCGCQ02102444)
 - Unwanted messages seen during source rpm/dpkg installation on Ubuntu (SCGCQ01958026)
 - Corrected opcode of MFI_CMD_TOOLBOX (SCGCQ02033111)
 - MR7.10: (SLE(S12 (SP4 driver module need to be compiled with "extern" retpoline flags (SCGCQ02034399)
 - Dev Linux B(ST script updates to (SAL-1.1902.1.3 (SCGCQ02075522)
 - MR7.9: Aero perf improvement - Change high IOPs reply queue count to 8 and reply batch count to 16 (SCGCQ01977946)
 - MR_7.10: Citrix Xenserver Readme file os support should be updated as per os matrix policy. (SCGCQ02115720)
 - Removed few debug counters from IO path (SCGCQ01942753)
 - Fixed compilation warnings due to reading non-atomic variable-"device_busy" using atomic_read API for older kernels(<3.17). (SCGCQ01965596)
 - Enhancement to add support for HO(ST_DEVICE_LI(ST DCMD in Linux driver(SCGCQ02051854 port of SCGCQ02016716)
 - Fix deadlock in few DCMDs timeout path due to re-acquiring of "reset_mutex" lock(SCGCQ02056151 port of SCGCQ02044603)
 
EnhancementRequests (19)
 - Added Aero support (SCGCQ01889127)
 - (Support added for High IOPs Reply queues(reply queues with interrupt coalescing ON) to improve Aero performance (SCGCQ01890975)
 - MR7.9: Add O(S (Support for RHEL 7.6 (SCGCQ01957415)
 - MR Aero: Driver should enable PCIe ExtTags (SCGCQ02016780)
 - Add support for Marlin(device ID- 0xd3) PCI ID. (SCGCQ01889122)
 - If any fusion register read returns all zeroes, driver will retry reading same register upto 3 times. (SCGCQ01965468)
 - Removed support for UEK kernels and (SLE(S12 (SP1 (SCGCQ02016741)
 - MR7.8 : Add rhel7.6 and sles12sp4 support (SCGCQ02069610)
 - (Support for multiple performance modes for Aero. (SCGCQ02072557)
 - (Support hybrid set of managed and non-managed vectors for 5.0 and onwards kernels (SCGCQ02018287)
 - MR7.10: Modify RPM spec file to be compatible with RHEL8 RPM framework (SCGCQ02011954) 
 - MR7.8 support for rhel8 and sles15sp1. (SCGCQ02063925)
 - MR 7.9: (SLE(S12 (SP4 O(S (Support (SCGCQ01940318)
 - Added driver support for PCI lane margining passthrough commands (SCGCQ01943619)
 - MR7.9: Add O(S (Support for OEL 7.6 (SCGCQ01966563)
 - (Supported DKM(S based source Deb/RPM for Ubuntu (SCGCQ02012043)
 - Driver should not issue fastpath IO to Region Lock Bypass queue. (SCGCQ02018278)
 - Use 32 bit atomic descriptor for Aero if firmware supports it. (SCGCQ01965225)
 - MR7.9: (Set 63-bit DMA mask in MR Linux driver (SCGCQ01981597)

07.708.05.00-1  - Moderate Impact/Low Probability of Occurrence
---------------------
MR 7.8

defects:
- FW flash is not needed for driver.(SCGCQ01593539)
- MR_7.8:Ubuntu 18.04 OS package description is mentioned as SAS 2.0.(SCGCQ01826712)
- MR7.8: Driver compilation fails on latest upstream kernel(>= v4.17), due to changes in
"queue_flag_set_unlocked" API.(SCGCQ01821588)
- MR7.8: Global SMP affinity setting is disabled incorrectly by driver under certain conditions.(SCGCQ01822883)
- MR7.8: Disable WRITE SAME commands from host for zeroout block ranges operations.(SCGCQ01823902)
- Alpha Release Version 07.708.03.00-1 - MR_LINUX_DRIVER_7.8 (38)
- MR7.8: Linux driver compilation fails on PPC (ppc64le) server(SCGCQ01861892)
- MR7.8: During probe, locking PCI config space while doing adp_reset is applicable to all fusion based
controllers.(SCGCQ01841413)
- MR7.8: Capture known OS limitations in Driver readme.(SCGCQ01888783)
- Fix deadlock in few DCMDs timeout path due to re-acquiring of "reset_mutex" lock.(SCGCQ02044603)
- Driver BST test cases need modification.(SCGCQ01664978)
- Driver fires a DCMD to incorrect Target ID’s to obtain Maximum Data transfer size (MDTS) of NVME
devices.(SCGCQ01786657 port of SCGCQ01760644)

(EnhancementRequest
- Update Linux Driver BST scripts and wrapper.(SCGCQ01529349)
- MR7.8: Enable irq poll in Linux driver to avoid CPU hard and soft lockups.(SCGCQ01571355)
- Improvement in driver debugging.(SCGCQ01753524)
- Retpoline compilation support for MR Linux drivers for Spectre_v2 vulnerability.(SCGCQ01763140)
- MR7.8: Lock access to controller's PCI config space from user space while Diag reset
operation is going on.(SCGCQ01824443)
- MR7.8: Add RHEL 6.10 Support.(SCGCQ01838376)
- MR7.8: Add SLES 15 OS Support.(SCGCQ01854853)
- MR7.8: Add Oracle Linux 6.10 OS Support.(SCGCQ01857765)
- MR7.8 : Add rhel7.6 and sles12sp4 support.(SCGCQ02069610)
- MR7.8 support for rhel8 and sles15sp1.(SCGCQ02063925)


07.707.04.00-1 - Moderate Impact/Low Probability of Occurrence
--------------------------
MR 7.7 (new)

Defects:
- Driver will use 64 bit request descriptor for sending IO to Ventura firmware.(SCGCQ01514452)
- FW flash is not needed for driver.(SCGCQ01593539)
- Modified driver prints to dump relevant FW provided values(part of controller info structure) in syslog.(SCGCQ01626839)
- Merge upstream patch "Convert timers to use timer_setup" to in-house and support timer_setup API in 4.15 kernels.(SCGCQ01586787)
- MR7.7: scsi_dma_map() is called twice in IO path.(SCGCQ01619432)
- Driver is incorrectly deciding combined reply queue mode for SAS3.0 controller(SCGCQ01633318)
- Updated driver's file- "OS_Support_list_mr7.7.txt" with CMA support enablement and retpoline compliant driver binaries.(SCGCQ01760521)
- Renamed scratchpad registers from scratchpad0 , scratchpad1 etc ... in order to align with firmware naming convention.(SCGCQ01440031)
-(SCGCQ01664978)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01440720 port of SCGCQ01430747)
- Driver should go through stream detection logic after it's finalized which path(fastpath vs non fastpath) IO will go through.(SCGCQ01483730 port of SCGCQ01468189)
- XenServer 7.3 OS support- MR 7.6.(SCGCQ01594134 port of SCGCQ01554012)
- Divert FastPath IO with Chain frame to Firmware path.(SCGCQ01598186 port of SCGCQ01593175)
- expose fw_outstanding and drv_outstanding variables to the OS level sys interface.(SCGCQ01475068 port of SCGCQ01019663)
- Driver should go through stream detection logic after it's finalized which path(fastpath vs non fastpath) IO will go through.(SCGCQ01542421 port of SCGCQ01468189)
- expose fw_outstanding and drv_outstanding variables to the OS level sys interface.(SCGCQ01542422 port of SCGCQ01019663)
- After a kill adpater, megasas_wait_for_adapter_operational waits for almost 360seconds before bailing out.(SCGCQ01619441 port of SCGCQ01615239)
- Setup IRQs only after Reply descriptors are allocated.(SCGCQ01542423 port of SCGCQ01506133)
- MR: Remove trace kernel RPMs from SUSE SLES11 SP4 driver iso images.(SCGCQ01594109 port of SCGCQ01563428)
- megasas_get_target_prop failing after OCR completed.(SCGCQ01619439 port of SCGCQ01607430)
- NVMe Task Management - Controller Reset Support (MegaRAID).(SCGCQ01592015 port of SCGCQ01545040)
- Updated OEL6_UEK and OEL7_UEK buildkit.(SCGCQ01443432 port of SCGCQ01439776)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01449786 port of SCGCQ01430747)
- Use pci_{alloc/free}_irq_vectors for >=4.12 kernels.(SCGCQ01449816 port of SCGCQ01442784)
- Setup IRQs only after Reply descriptors are allocated.(SCGCQ01514459 port of SCGCQ01506133)
- Driver will use 64 bit request descriptor for sending IO to Ventura firmware.(SCGCQ01523087 port of SCGCQ01514452)
- Increased JBOD FPIO timeout by 1 sec to workaround hardware bug which causes timeout 1 sec earlier than provided timeout value.(SCGCQ01542419 port of SCGCQ01449957)

EnhancementRequests (23)
- Use pci_{alloc/free}_irq_vectors for >=4.12 kernels.(SCGCQ01442784)
- Few officially unsupported PCI IDs are removed from MR7.7 driver code.(SCGCQ01598587)
- XenServer 7.4 OS support - MR 7.7.(SCGCQ01628129)
- Increased JBOD FPIO timeout by 1 sec to workaround hardware bug which causes timeout 1 sec earlier than provided timeout value.(SCGCQ01449957)
- Rebase inbox megaraid_sas driver to inhouse to reduce two different code base for maintenance.(SCGCQ01578030)
- MR_Aero: Create timer based thread in MR drivers to detect firmware FAULT.(SCGCQ01157766)
- Remove UpdateIoMetric and hence adapter level spinlock from IO path(SCGCQ01522127)
- Create cpu to msix table for kernel provided PCI_IRQ_AFFINITY (>=4.12 kernel).(SCGCQ01598134)
- OS driver support for Oracle Linux 7.5 - MR 7.7.(SCGCQ01586106)
- OS Driver Support for Ubuntu 18.04- MR 7.7.(SCGCQ01586128)
- Support RHEL7.5 GCA (3.10.0-862.el7.x86_64).(SCGCQ01586135)
- Early detection of faulty controller.(SCGCQ01599562)
- Change attribution language from Avago to Broadcom and update copyright end year.(SCGCQ01753095)
- Offload R5/R6 division to driver.(SCGCQ01513544)
- Update Linux Driver BST scripts and wrapper.(SCGCQ01529349)
- Marlin support is added to drivers.(SCGCQ01440724)
- Remove support for RHEL7.1, OEL7.2 and SLES12.(SCGCQ01449982)
- Optimize code around (raid context) in IO path.(SCGCQ01598187)
- Removed support of RHEL7.1, SLES12 and OEL7.2.(SCGCQ01600475)
- FW OCR Debug Mechanism - triggerSnapDump.(SCGCQ01520447)
- Set SLD bit in RAID map when "enableSLDOnAllRWIOs" is enabled.(SCGCQ01715619)
- Revert code changes related to iMR performance throttling.(SCGCQ01749962)
- Revert changes added in driver to divert FastPath IO with Chain frame.(SCGCQ01752939)


Version 07.705.04.00-5 - Moderate Impact/Low Probability of Occurrence

Defects (7)
- Provided driver workaround to reset __GFP_WAIT flag while allocating IO request frames.(SCGCQ01394892)
- Driver will use 64 bit request descriptor for sending IO to Ventura firmware.(SCGCQ01514452)
- Set DMA mask after FW is in READY state in PCI resume path of megaraid_sas driver(SCGCQ01389431)
- Fixed few dev found and coverity reported defects(SCGCQ01392652)
- Selective stream detection logic in driver(SCGCQ01392643)
- During PCI remove, set unload flag after scsi_remove_host is called.(SCGCQ01392656)
- update LD map after populate drv_map, increase wait in IOCTL, fix index in error handling, rework in refiring DCMDs.(SCGCQ01415439)
- Added support for threaded interrupts.(SCGCQ01615015 port of SCGCQ01498747)
- Driver should go through stream detection logic after it's finalized which path(fastpath vs non fastpath) IO will go through(SCGCQ01483730 port of SCGCQ01468189)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01455132 port of SCGCQ01430747)
- MR: OEL 7.4 and 6.x x86_64 RPMs do not have the correct kernel versions.(SCGCQ01611888 port of SCGCQ01607445)
- expose fw_outstanding and drv_outstanding variables to the OS level sys interface.(SCGCQ01475068 port of SCGCQ01019663)
- Updated correct supported kernel version of Ubuntu16.04 in driver's document- OS_support_list_mr7.5.txt.(SCGCQ01564604 port of SCGCQ01454090)
- Added NVME passthru support in MR linux driver.(SCGCQ01424605 port of SCGCQ01407028)
- Updated correct supported kernel version of Ubuntu16.04 in driver's document- OS_support_list_mr7.5.txt.(SCGCQ01455206 port of SCGCQ01454090)
- Added NVME passthru support in MR linux driver.(SCGCQ01455135 port of SCGCQ01407028)
- Updated OEL6_UEK and OEL7_UEK buildkit.(SCGCQ01443433 port of SCGCQ01439776)
- Setup IRQs only after Reply descriptors are allocated.(SCGCQ01514459 port of SCGCQ01506133)
- Use pci_{alloc/free}_irq_vectors for >=4.12 kernels.(SCGCQ01449816 port of SCGCQ01449816)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01449786 port of SCGCQ01430747)
- Set DMA mask after FW is in READY state in PCI resume path of megaraid_sas driver.(SCGCQ01392672 port of SCGCQ01389431)


EnhancementRequests (10)
- MR7.4: Add SLES12 SP3 OS support.(SCGCQ01396756)
- Added support for RHEL7.4.(SCGCQ01455156)
- Added driver support for OEL7.4.(SCGCQ01396747)
- Increased JBOD FPIO timeout by 1 sec to workaround hardware bug which causes timeout 1 sec earlier than provided timeout value.(SCGCQ01449957)
- Added support for threaded interrupts.(SCGCQ01498747)
- MR7.4: OS driver support for RHEL 7.4.(SCGCQ01396738)
- Added support for SLES12 SP3.(SCGCQ01455167)
- Added driver binary support for Xenserver7.2.(SCGCQ01393249)
- Remove support for RHEL7.1, OEL7.2 and SLES12.(SCGCQ01449982)
- Removed support for few OS to align with OS support matrix policy.(SCGCQ01393194)


Version 7.703.07.00- Moderate Impact/Low Probability of Occurrence
---------------------
fixes:
- Send sense buffer upper 32bits inside IOC INIT frame.(SCGCQ01315987)
- MR: On OEL 6.x/7.x with UEK kernels - megaraid_sas.conf file from the kmod rpm does not match kernel version.(SCGCQ01319368)
- pass upper 32 bits of version buffer and system information buffer to FW inside IOC INIT frame.(SCGCQ01326366)
- Workaround changes for FW MFA frame pull issue.(SCGCQ01338087)
- Log dmesg if IOC INIT fails in IOMMU and RDPQ enabled enviornment for user information only.(SCGCQ01338097)
- Validated if any of DMA buffers pool which should be in same 4GB region does not cross 4GB boundary.(SCGCQ01338372)
- Memset to zero for MFI command frame for IOC INIT and use lower_32_bits() macro to get lower 32bits of DMA address passed to FW.(SCGCQ01341287)
- Removed Crusader ID(device ID- 0x0015) from supported PCI IDs of MR7.2 linux driver.(SCGCQ01350963)
- MR7.3: Code review defect - ioc_init_frame not freed during kernel module unload.(SCGCQ01384694)
- MR7.2: In megasas_issue_tm() SMID needs to be used for Task abort case only.(SCGCQ01315252)
- Incorrect processing of IOCTL frames for SMP/STP commands.(SCGCQ01383823)
- Set cmd_status inside DCMD/IO/header frame to MFI_STAT_OK to wake up all pended IOCTLs.(SCGCQ01298582)
- Removed print "Failed from megasas_complete_cmd" from PD CFQ sequence DCMD completion path.(SCGCQ01321565)
- Do not switch DMA mask to meet same 4gb requirement. IOMMU does not work well with such DMA mask switch.(SCGCQ01342578)
- Allocated MFI frame size and the size of MPT chain frame(Where MFI frame resides for MFI MPT passthru commands) should match.(SCGCQ01342650)
- Minimum possible value for module parameter- resetwaittime should be 1 secs instead of 0 secs.(SCGCQ01344137)
- Set DMA mask after FW is in READY state in PCI resume path of megaraid_sas driver.(SCGCQ01389431)
- MR7.3: Data miscompare found with WB secure VD RAID 1 with LSA sending IOCTLs in parallel.(SCGCQ01378684)
- Set cmd_status inside DCMD/IO/header frame to MFI_STAT_OK to wake up all pended IOCTLs.(SCGCQ01381770 port of SCGCQ01298582)
- MR: On OEL 6.x/7.x with UEK kernels - megaraid_sas.conf file from the kmod rpm does not match kernel version.(SCGCQ01320324 port of SCGCQ01319368)
- Use IOC_INIT frame once driver has verified IOC_INIT frame allocation was successful.(SCGCQ01455132 port of SCGCQ01430747)
- Updated correct supported kernel version of Ubuntu16.04 in driver's document- OS_support_list_mr7.5.txt.(SCGCQ01455206 port of SCGCQ01454090)
- Added NVME passthru support in MR linux driver.(SCGCQ01455135 port of SCGCQ01407028)
- Updated OEL6_UEK and OEL7_UEK buildkit.(SCGCQ01443433 port of SCGCQ01439776)
- Minimum possible value for module parameter- resetwaittime should be 1 secs instead of 0 secs.(SCGCQ01344142 port of SCGCQ01344137)


EnhancementRequests:
- Added support for 64bit DMA mask for invader.(SCGCQ01294199)
- MR7.3: add support for Citrix XenServer 7.1 OS.(SCGCQ01257971)
- Send current time to FW during IOC init.(SCGCQ01307072)
- Added support for RHEL7.4.(SCGCQ01455156)
- MR7.3: add support for OEL 6.9.(SCGCQ01289005)
- Added support for threaded interrupts.(SCGCQ01498747)
- Added support for 64bit DMA.(SCGCQ01301940)
- Added support for SLES12 SP3.(SCGCQ01455167)



Version 7.702.06.00- Moderate Impact/Low Probability of Occurrence
---------------------
Defects (47)
 - Reset MPT frame field cmd_completed while retrurning it back to free pool.(SCGCQ01176530)
 - Optimized R1 FP write code.(SCGCQ01191077)
 - Before populating driver RAID map copy memset drv_map to zero and ldTgtIdtoLd array to 0xff(SCGCQ01204087)
 - Initialize stream detection array properly.(SCGCQ01204096)
 - On SPARC/Big endian host, need to convert peerSMID to little endian to CPU before accessing(SCGCQ01216698)
 - Fixed coverity reported issues and changed name of few functions.(SCGCQ01219231)
 - Don't set tm_capable for JBDO when PD CFG SEQ map is not available(SCGCQ01226222)
 - Remove local defination FALSE/TRUE and use OS provided false/true.(SCGCQ01256130)
 - Used vmalloc for crash dump buffers and driver's local RAID maps(SCGCQ01270059)
 - Reduce size of fusion_context allocation during driver load by moving load_balance_info array out, and try vmalloc if kmalloc fails.(SCGCQ01183280)
 - Flooding of messages- "BRCM: IO does not end on page boundary; sge_len" while running RAW IOs.(SCGCQ01189815)
 - Fixed data corruption by asking OS not to do merging of IOs to avoid SGE holes(SCGCQ01231229)
 - Code review defect: create separate function for allocating RAID maps(SCGCQ01282924)
 - Removed Crusader ID(device ID- 0x0015) from supported PCI IDs of MR7.2 linux driver(SCGCQ01350963)
 - Updated OS to send page aligned SGEs by calling blk_queue_virt_boundary(SCGCQ01206279)
 - Use vmalloc followed by memset to zero instead of vzalloc in driver code.(SCGCQ01206316)
 - MR_ValidateMapInfo issue on bigendian platform (In some case Detect Ghost VDs)(SCGCQ01213952)
 - Fixed code review defects(SCGCQ01254323)
 - Removed code inside macros VD_EXT_DEBUG, SPAN_DEBUG and enahnce prints in OCR path(SCGCQ01270056)
 - FW fault happens as driver wrongly fill numSGE=0.(SCGCQ01274103)
 - Code optimization and enhanced prints for debugging(SCGCQ01224881)
 - Remove unsupported PCI Device IDs from the driver code(SCGCQ01234256)
 
 - Resolved conflict of PCI device ID-0x0015(SCGCQ01254317)
 - MR7.2: In megasas_issue_tm() SMID needs to be used for Task abort case only(SCGCQ01315252)
 - Save interfaceType for each sysPDs inside SCSI device's private data field which will persists until sysPD is removed/deleted.(SCGCQ01216464)
 - Code Optimization and enhanced prints(SCGCQ01223300)
 
 - MR 7.1: Linux OS crash when powering off enclosure during I/O(SCGCQ01229442)
 - Return pending IOs with status DID_REQUEUE instead of DID_RESET to SCSU layer before doing OCR(SCGCQ01231846)
 - MR7.2: Port changes from upstream to make in-house MR 7.2 code to be consistent with upstream code(SCGCQ01282321)
 - Add print for partially copied SCSI IO and fix few endianness issues(SCGCQ01224305)
 - Linux Driver 07.700.23.00/Getting megaraid_sas prints during startup of OS(SCGCQ01255074)
 - aen class range check to avoid kernel panic(SCGCQ01256126)
 - Corrected bitmap macros inside struct RAID_CONTEXT35(SCGCQ01269453)
 - Set cmd_status inside DCMD/IO/header frame to MFI_STAT_OK to wake up all pended IOCTLs.(SCGCQ01298582)
 - Fix few dev found issues(SCGCQ01226224)
 - On OEL SPARC (Big Endian), Linux MR 7.1 driver loading fails to initialize Ventura which has RDPQ support enabled(SCGCQ01229897)
 - Fixed few code collab defects/comments(SCGCQ01202237)
 - Remove throttle IOs prints in IO path and add sysfs parameter to reflect number of R1 FP writes(SCGCQ01204099)
 - Ventura MR-7.0.1 RHEL 7.2 driver: ERR messages when installing driver 7.700.20.00(SCGCQ01222990)
 - Use do_div() kernel API to do modulo operation of 64 bit dividend and 32bit divisor .(SCGCQ01243263)
 - megasas_complete_cmd_dpc_fusion() will be called with 1 sec delay inside function megasas_wait_for_outstanding_fusion(SCGCQ01256116)
 - Allocated MFI frame size and the size of MPT chain frame(Where MFI frame resides for MFI MPT passthru commands) should match(SCGCQ01342650)

EnhancementRequests (17)
 - Big endian architecture is now support for Ventura generation of MR HBA.(SCGCQ01256016)
 - Fixed the problem of sync_irq not being called when MSI-x are disabled.(SCGCQ01206307)
 - Port changes from MR7.0 and MR6.13 critical fixes to MR7.1(SCGCQ01167939)
 - In megasas_build_ldio_fusion, code to set controller CPU affinity can be optimized(SCGCQ01216486)
 - Set device queue depth same as controller's can_queue for SCSI MQ mode(SCGCQ01271569)
 - Add SLES 11 32-bit build kit support to Ventura MR.(SCGCQ01214721)
 - Ported fixes from MR 6.13 to MR 7.1(SCGCQ01222522)
 - Added support for RHEL7.3(SCGCQ01224300)
 - Support SPARC/PPC/ARM (Big/Little Endian). Fix Endianess issue in MR Ventura driver.(SCGCQ01183275)
 - Added DCMD interface to read target properties for SCSI device(VDs and JBODs both)(SCGCQ01220142)
 - Added KMOD RPM support for OEL7.3 UEK.(SCGCQ01227476)
 - R1 Write IOPs improvement(SCGCQ01213232)
 - Extra code for bug in A0 ventura is removed. Optimized Descriptor write as Ventura required 32 bit in major IO Path operation.(SCGCQ01215347)
 - Remove Crusader device support from driver(SCGCQ01259175)
 - Don't re-issue Reset on the way back OCR(SCGCQ01215089)
 - Rework start_vm_build script used for VBAS build and new build infrastructure for DKMS RPMs(SCGCQ01261800)
-

Version 7.700.26.00- Moderate Impact/Low Probability of Occurrence
---------------------
Enhancement:
- Added support for ThinkSystem HBA and RAID.


Version 6.812.08.00 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes:
- Modified not to send outstanding IOs back to SML with DID_RESET host_byte but return IOs back with host_byte DID_REQUEUE before doing OCR. (SCGCQ01278656 Port Of Defect SCGCQ01231846)

Enhancement
- Added support for SLES 12.2


Version 6.812.07.00 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes
 - Changed timeout value for DCMDs get_bios_data and get_pd_info 180 seconds to keep it aligned with other DCMDs' timeout value. (SCGCQ00884247)
 - Do not allow MFI frame to be freed from DCMD fire context when already an OCR is in progress. (SCGCQ00879190)
 - Fixed an issue where driver always worked in non RDPQ mode even the running firmware did not support RDPQ. (SCGCQ00872542)
 - Moved SCSI layer interaction code out of reset_mutex in AEN thread to prevent deadlock around reset_mutex. (SCGCQ00868731)
 - Convert supported JBOD count value returned by firmware in CPU format and then use the same value for further validation (SCGCQ00837088)
 - Fixed an issue where unevenSpan configuration of R1 would not have proper load balancing for FP READ. SCGCQ00646224
 - Added timeout value for wait_event. (SCGCQ00249742)
 - Enabled hostlockless flag of SCSI host for RHEL6 and clones for async IO submission from SCSI mid layer. (SCGCQ00884242)
 - Fixed an issue where double freeing of MFI frame in case of MFI IO timeout in polled mode could occur. (SCGCQ00837932)
 - Added synchronization between OCR thread and AEN thread, so that there should not be any PCI write from AEN thread during OCR (SCGCQ00836410)
 - Added IO timeout value for SCSI management commands for JBOD. (SCGCQ00750452)
 - Fixed a JBOD performance issue due to incorrect MSI-x index set in request desc. (SCGCQ00619694)
 - Changed state machine of firmware crash dump collection to prevent file system on VD being set to Read-only mode after ECC error injection. (SCGCQ00608705)
 - Fixed an issue where incorrect messages such as LSI SAS2.0 were printed for MR driver. (SCGCQ00298201_
 - Fixed an issue where the driver sent an incorrect region type "REGION_LOCK_EXCLUSIVE" set to FW for RAID level >=5
 - Changed error handling for DCMD failure cases to allow graceful exit for not fatal errors. (SCGCQ00868661)
 - Free task management frame after dumping the task management reply frame data to ensure that TM reply frame will have valid data returned by firmware. (SCGCQ00860038)
 - Release reset_mutex inside OCR function, if adapter is already killed to prevent a kernel panic. (SCGCQ00857740)
 - Increased timeout to 180 seconds for flush cache and shutdown controller DCMDs to prevent kernel panic when DCMDs fired during driver's shutdown. (SCGCQ00841491)
 - Fixed an issue where traversed LDs at multiple places up to maximum 256 were limited to 64. (SCGCQ00652795)
  - Fixed an issue where the driver crashed when msix_disable=1 was passed to the boot time parameter. (SCGCQ00383508)
 - Fixed an issue where kernel panic seen while deleting VD and background IOs running. (SCGCQ00803468)
 - Fixed an issue where the driver was not sending DCMD- MR_DCMD_CTRL_SET_CRASH_DUMP_PARAMS after OCR. (SCGCQ00601138)
 - Fixed an issue where the kernel panicked inside PCI subsystem because of IRQs not freed before disabling MSI-X interrupts (SCGCQ00827403)
 - Disabled SED drive JBOD support. (SCGCQ00751296)
 - Fixed multiple OCRs triggering hits Exception Core issue (SCGCQ00707592)
- Fixed an issue where the firmware faulted due to invalid regionlock Flags set by Driver. (SCGCQ00796461)
- Fixed an issue where subsequent reads of state value from hardware resulted different values and could lead to a timeout in and a non working adapter. (SCGCQ00709216)
- Fixed an issue where Offline VD caused boot hangs in SLES 11 (SCGCQ00284564)
 - Disabled SPAN_DEBUG and set get_arm_from_strip to print if firmware supports UnevenSpan. (SCGCQ00365846)
 - Added check to validate ldcount exposed in firmware RAID map for legacy firmware.  If ldcount is more than 64, fail RAID map validation. (SCGCQ00820349)
 - Fixed an issue where the Linux kernel crashed when AEN and LD Sync commands were issued frequently. (SCGCQ00712031)
 - Fixed an issue where duplicate disk(s) were seen on controller after loading Linux driver during OS installation, (SCGCQ00568992)
 - Fixed an issue where kernel panic could occur at driver load time on 3.0 kernels (i.e. SLES11 SP2, SLES11SP3). (SCGCQ00561505)
 - Changed driver to return SCSI command back to mid layer if the controller has any critical hardware errors. SCGCQ00362023
 - Fixed an issue where the driver did not do Load balance for R1 READ due to wrong stats counters. (SCGCQ00677516 Port of Defect - SCGCQ00674872)
 - Fixed potential duplicate IOCinit frames being fired by VMware5 VF driver during OCR. (SCGCQ00571967 PORT OF SCGCQ00571679)
 - Fixed OS crash issue on SCSI IO timeout (SCGCQ00631210 PORT OF SCGCQ00625137)
 -Fixed an issue where the kernel panicked due to MFI/MPT pass-through command timeout and later finished from Interrupt context. (SCGCQ00307867 PORT OF - SCGCQ00302080)
 - Fixed an issue where megasas_poll_wait_aen was cleared before poll syscall returns causing to lose events (SCGCQ00575192 PORT OF SCGCQ00574787)
 -Fixed an issue where data corruption observed on JBODs while running IOs with 32k block size. (SCGCQ00530992 PORT OF SCGCQ00523780)
 - Fixed MPC kernel panic during chassis power cycle if AEN completes and detach is called before event workqueue runs. (SCGCQ00647390 PORT OF SCGCQ00645836)
 - Fixed an issue where kernel crashed in some cases, where megaraid_sas driver is loaded but controller is not present. (SCGCQ00282968 PORT OF SCGCQ00282067)


Enhancements:  
 - Set queue depth for syspD based on interface type (SCGCQ00879700)
 - Updated module Meta data (module description and module author) with Avago replacing LSI. (SCGCQ00801961)
 - Set OS provided timeout value for sysPD non read-write IOs (SCGCQ00764795)
 - Performance tuning for SMP affinity is implemented for distros's which support irq_set_affinity_hint API. (SCGCQ00623697)
 - Optimized OCR path to enable interrupt and make HBA OPERATIONAL after driver has fired LD_MAP_GET_INFO DCMD. (SCGCQ00768402)
 - Added module parameter to turn on/off SMP affinity code. (SCGCQ00666706)
 - Driver will do load balance for N Drive Raid 1 volumes. (SCGCQ00634064)
 -Functionality in driver is added to differentiate between iMR and MR at firmware initialization time. (SCGCQ00361244)
 - Uneven Span support added in Driver. (SCGCQ00319104)
 - Driver code is updated such way that it can work for any block size drive, if the rest of the system has proper support for the same. (SCGCQ00259244)
 - Implemented online controller reset if controller is not responding at driver load time. (SCGCQ00820389)
 - Added SCSI residual bytes support to the megaraid_sas Linux driver (SCGCQ00347089)
 - Use sequence number for JBOD FastPath I/Os to eliminate command block after drive replacement (SCGCQ00806534)
 - Big endian architecture support added for MR Linux driver (SCGCQ00526911)
 -  Driver support is added for 3108 C0 chip combine reply queue ON (SCGCQ00354586)
 - Added support 240 VD feature (SCGCQ00622703)
 - Added Firmware crash dump collection support (SCGCQ00550369)
 - Added support for large I/O 1MB transfer size (SCGCQ00816313)
 - Changed the max sg table size to 64. Old setting was 70 (SCGCQ00653992)
 - Added driver support for task management for Jbod or VD (tmCapable) (SCGCQ00854635)
 - Added support for SED JBOD in MR Linux driver (SCGCQ00711555)
 - Changed code to complete IOCtls posted just before a kill adapter so user space applications do not hang. (SCGCQ00759916)


Version 6.810.09.00 - Moderate Impact/Low Probability of Occurrence
---------------------
 Fixes:

 - Fixed an issue where deadlock may occur when the Automatic Event Notification thread runs in parallel with error handler thread (SCGCQ00911332, Port of SCGCQ00868731)

 - Fixed an issue where driver will operated in RDPQ mode regardless of whether firmware has advertised support or not (SCGCQ00872542)

 - Fixed an issue where system may reset with error "BUG: unable to handle kernel NULL pointer dereference at 00000000000000d0" preceded by error "megasas: target reset FAILED!!" (SCGCQ00875223)

 - Fixed an issue where driver MFI frames could be freed twice (SCGCQ00879190)

 - Fixed an issue where some out-of-band commands had different timeouts than others (SCGCQ00884247)

 - Fixed an issue where performance was lower on async IO submissions from the SCSI mid layer (SCGCQ00884242)

 - Fixed an issue where a kernel panic may occur if the system is reset or fail to reboot (SCGCQ00859634, Port of SCGCQ00857740)

 - Fixed an issue where Task Management frames were not being dumped after the Tast Management Reply frame data (SCGCQ00860038)

 - Fixed an issue where a fatal error may occur when an out-of-band command times out during an Online Controller Reset (SCGCQ00882011, Port of SCGCQ00868661)

 - Fixed an issue where kernel may hang when many commands are timing out or many Automatic Event Notifications are being processed (SCGCQ00857245)

 - Fixed an issue where megaraid_sas module was not being included inside initrd/initramfs (SCGCQ00880965)

 - Fixed an issue where kernel may panic if driver does not setup IRQs for non-MSI-x interrupt mode (SCGCQ00870263, Port of SCGCQ00867873)

 - Fixed an issue where driver return code is based on command completion rather than command return code (SCGCQ00856103, Port of SCGCQ00856089)

 - Fixed an issue where Tape drives may not be detected by the Operating System (SCGCQ00914385, Port of SCGCQ00911702)

 - Fixed an issue where max_sectors per IO request may be set to more than firmware can handle (SCGCQ00917992, Port of SCGCQ00917399)
 
- Fixed an issue where an IERR may occurr on heavy IO with Failover (SCGCQ00864111, Port of SCGCQ00736612)
 
 
Enhancements:

 - Enhanced queue depths in driver for physical disks based on interface type (SCGCQ00879700)

 - Improved naming of internal functions (SCGCQ00866064)

 - Updated module parameter "rdpq_enable" default to "1" (enable RQPQ mode) (SCGCQ00871565)

 - Enhanced reply queue to support queue depth greater than 1K (SCGCQ00853521)

 - Added feature for driver to support Task Management for JBOD and Virtual Drives (SCGCQ00854635)

 - Added module parameter to disable 1M IO support and set default to enable 1M IO support (SCGCQ00911362)

 - Enhanced tasklet initialization so it would occur before setting up IRQs (SCGCQ00914393, Port of SCGCQ00911709)

 - Simplified HB handling for SR-IOV (SCGCQ00864113, Port of SCGCQ00700580)

 - Enhanced driver to update Online Controller Reset capability when it changes (SCGCQ00914389, Port of SCGCQ00908352)

 - Added feature to print Critical, Fatal and Dead firmware events into system logs (SCGCQ00868723, SCGCQ00882010, Port of SCGCQ00866176)

 - Enhanced HB handling to align with behavior on other Operating Systems (SCGCQ00864117, Port of SCGCQ00707323)

 - Removed excess dead code (SCGCQ00850012)

Version 6.808.16.00 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes:
- Fixed an issue where a deadlock may occur around reset_mutex when Automatic Event Notification threads run in parallel with error handlers - (SCGCQ00911332, Port of SCGCQ00868731)
- Fixed an issue where scanning of Tape drives does not occur depending on whether the drive state is set to systemPD or not - (SCGCQ00914385, Port of SCGCQ00911702)
- Fixed an issue where max_sectors may be set larger than what firmware can support - (SCGCQ00917992, Port of SCGCQ00917399)
- Fixed an issue where kernel may panic due to driver not setting up IRQs for non MSI-x interrupt mode - (SCGCQ00870263, Port of SCGCQ00867873)
- Fixed an issue where driver may halt firmware due to improper error handling for DCMD failure cases - (SCGCQ00882011, Port of SCGCQ00868661)
- Fixed an issue where driver may hang kernel due to deadlock - (SCGCQ00857245)
- Fixed an issue where system may crash due to timeout for flushing cache and shutting down controller DCMDs was not long enough - (SCGCQ00841491)
- Fixed an issue where deadlock may occur between Online Controller Reset and Automatic Event Notification processing function - (SCGCQ00846933)
- Fixed an issue where PCI writes from Automatic Event Notification thread were occurring during Online Controller Reset - (SCGCQ00836410)
- Fixed an issue where MFI frames linked list may corrupt due to double-freeing of frame in the case of an MFI IO timeout - (SCGCQ00837932)
- Fixed an issue where kernel may panic inside PCI subsystem due to IRQs not freed before disabling MSI-X interrupts - (SCGCQ00827403)
- Fixed an issue where ldcount was not validated for non-240VD firmware - (SCGCQ00820349)
- Fixed an issue where a command block would occur for JBODs with FastPath IOs after a drive is replaced - (SCGCQ00806534)
- Fixed an issue where 1MB IO support was not supported controller-wide - (SCGCQ00816313)

Enhancements:
- Set DMA alignment to 8 bytes for PI-enabled VDs - (SCGCQ00928796, Port of SCGCQ00928176)
- Added a parameter to support disabling 1MB IO support - (SCGCQ00911362)
- Added support for printing Critical, Fatal and Dead Firmware events into system logs - (SCGCQ00882010, Port of SCGCQ00866176)
- Added support for driver to perform an Online Controller Reset at driver load time if the controller is not responding - (SCGCQ00820389)

Version 6.808.14.00 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes
- Fixed an issue where controller may reset or "MonTask: line 1276" error will occur with JBOD present (SCGCQ00837088)
- Fixed a performance issue on RAID1 with 256k IO size (SCGCQ00674872)
- Fixed a performance issue on RAID1 reads with FastPath enabled (SCGCQ00646224)
- Fixed an issue where an Online Controller Reset may take an unusually lon time (SCGCQ00420374)
- Fixed an issue where a controller firmware crash may not be recognized by driver (SCGCQ00249742)
- Fixed an issue where an MFI frame may be freed twice on MFI command timeout (SCGCQ00837932)
- Fixed an issue where the firmware may fault in an Automatic Event Notification fires during an Online Controller Reset before the chip is in READY state (SCGCQ00836410)
- Fixed an issue where there was no IO timeout value for SCSI management commands for Secure JBOD (SCGCQ00750452)
- Fixed a performance issue on SSDs in JBOD mode (SCGCQ00619694)
- Fixed an issue where file system on a VD can go to read-only on ECC error detection (SCGCQ00608705)
- Fixed an issue where disks may not be found during installation after loading the driver (SCGCQ00299643)
- Fixed an issue where a kernel panic may occur when cable pulled during system reboot (SCGCQ00841491)
- Fixed an issue where 240VD support was not fully implemented (SCGCQ00652795)
- Fixed an issue where the driver may crash if msix_disable=1 is passed to kernel as boot parameter (SCGCQ00383508)
- Fixed an issue where IO errors may occur when connected to a Tape drive (SCGCQ00399947)
- Fixed an issue where kernel may hang due to megaraid_sas driver deadlock (SCGCQ00857245)
- Fixed an issue where kernel may panic when deleting VD and background IO is occurring (SCGCQ00803468)
- Fixed an issue where crash dump may be disabled after an Online Controller Reset (SCGCQ00601138)
- Fixed an issue in 32bit OSs where driver may not load on boot (SCGCQ00362423)
- Fixed an issue where deadlock may occur (SCGCQ00846933)
- Fixed an issue where a kernel panic may occur because IRQs are not freed before disabling MSI-X interrupts (SCGCQ00827403)
- Fixed an issue where multiple Online Controller Resets can trigger a Core Exception (SCGCQ00707592)
- Fixed an issue where crash dump may not be performed properly (SCGCQ00593374)
- Fixed an issue where firmware may fault with CacheCade (SCGCQ00796461)
- Fixed an issue where adapter may hang (SCGCQ00709216)
- Fixed an issue where an offline VD may cause boot hangs (SCGCQ00284564)
- Fixed an issue where kernel may panic (SCGCQ00820349)
- Fixed an issue where kernel may crash in megaraid_sas driver with CacheCade if there are many Automatic Event Notifications and LD sync operations occurring (SCGCQ00712031)
- Fixed an issue where system may hang with CacheCade (SCGCQ00687881)
- Fixed an issue where the same disk may show multiple times in OS (SCGCQ00568992)
- Fixed an issue where kernel may panic on Linux kernels version 3.0 or greater (SCGCQ00561505)
- Fixed an issue where invalid IO statistics may be provided if driver supports more than just 512b sector drives (SCGCQ00282615)
- Fixed an issue where driver fails to reboot system due to outstanding IOs in SCSI mid-layer when controller is in error state (SCGCQ00362023)

Enhancements
- Added ability for JBOD IOs going via firmware path to use timeout value provided by OS (SCGCQ00764795)
- Added a retry of IO commands as LDIO if raid map sync is failed with MFI_STAT_CONFIG_SEQ_MISMATCH (SCGCQ00712510)
- Added support for 4k sector drives if the system supports it (SCGCQ00259244)
- Added support for driver to perform an Online Controller Reset if the controller is not responding (SCGCQ00820389)
- Fixed an issue where system may hang on S3 resume (SCGCQ00758933)
- Added a feature to prevent command block with FastPath after JBOD drive replacement (SCGCQ00806534)
- Enhanced 1MB IO support (SCGCQ00816313)
- Added support for "megaraid_sas.disable_ext_io=1" boot parameter to disable 1M IO support (SCGCQ00911362)
- Added support for Secure JBOD (SCGCQ00711555, SCGCQ00753765)
- Fixed an issue where user space applications may hang if IOCtl is sent prior a kill adapter issued (SCGCQ00759916)
- Fixed an issue where OS may crash on a SCSI IO timeout (SCGCQ00631210)
- Fixed an issue where system may fail to reboot or will kernel panic on init 6 if controller has faulted (SCGCQ00859634)
- Fixed an issue where firmware may fault (SCGCQ00702536)
- Fixed an issue where controller may crash during system power cycle (SCGCQ00647390)
- Fixed an issue where kernel may crash when megaraid_sas driver is loaded but no MegaRAID controllers are present (SCGCQ00282968)



Version 6.806.09.00 - New Function Only/No fixes
-------------------





Lenovo Data Center Group Linux OS Support Home Page
linux.lenovo.com

© 2018-2022 Lenovo. All rights reserved

LSI Storage Authority Software (For Linux)



LSI Storage Authority Software

Supported controllers:
	ThinkSystem RAID 530-8i PCIe 12Gb Adapter  (7Y37A01082)
	ThinkSystem RAID 530-4i Flex Adapter       (7M17A03932)
	ThinkSystem RAID 530-4i Flex Adapter       (7M27A03918)
	ThinkSystem RAID 530-8i Dense Adapter      (SD530 RAID)
	ThinkSystem RAID 530-16i PCIe 12Gb Adapter (4Y37A09727)
	ThinkSystem RAID 540-8i PCIe Gen4 12Gb Adapterr  (4Y37A78834)
	ThinkSystem RAID 540-16i PCIe Gen4 12Gb Adapter   (4Y37A78835)
	ThinkSystem RAID 940-8i 4GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09728
	ThinkSystem RAID 940-8i 8GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09729
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09730
	ThinkSystem RAID 940-32i 8GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09733
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Internal Adapter for 4Y37A09735
	ThinkSystem RAID 730-8i 1GB Cache PCIe 12Gb Adapter  (7Y37A01083)
	ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter  (4Y37A09722)
	ThinkSystem RAID 930-8i 2GB Flash PCIe 12Gb Adapter  (7Y37A01084)
	ThinkSystem RAID 930-16i 4GB Flash PCIe 12Gb Adapter (7Y37A01085)
	ThinkSystem RAID 930-24i 4GB Flash PCIe 12Gb Adapter (7Y37A01086)
	ThinkSystem RAID 930-8e 4GB Flash PCIe 12Gb Adapter  (7Y37A01087)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M17A03933)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M27A03917)
	ThinkSystem  RAID 930-16i 8GB Flash PCIe 12Gb Adapter(4Y37A09721)
	ServeRAID M1210 SAS/SATA Controller    (00JY194)
	ServeRAID M1215 SAS/SATA Controller    (46C9114)
	LSI SAS3004 RAID                       (NA-SAS3004-B)
	LSI SAS3004 RAID                       (NA-SAS3004-N)
	ServeRAID M5210 SAS/SATA Controller    (46C9110)
	ServeRAID M5225-2GB SAS/SATA Controller(00AE938)
	ServeRAID M5215 with 2GB Flash Enablement Flex System x240 M5   (00JX142)
	ServeRAID M5210e SAS/SATA Controller   (46C9117CTO)
	ThinkSystem 430-8i SAS/SATA 12Gb HBA   (7Y37A01088)
	ThinkSystem 430-16i SAS/SATA 12Gb HBA  (7Y37A01089)
	ThinkSystem 430-8e SAS/SATA 12Gb HBA   (7Y37A01090)
	ThinkSystem 430-16e SAS/SATA 12Gb HBA  (7Y37A01091)
	ThinkSystem 430-8i SAS/SATA 12Gb Dense HBA  (NA-StarkSASHBA)
	ThinkSystem 440-16e SAS/SATA PCIe Gen4 12Gb HBA for 4Y37A09724
	ThinkSystem 440-16i SAS/SATA PCIe Gen4 12Gb Internal HBA for 4Y37A09725
	N2215 SAS/SATA HBA   (47C8675)
	N2225 SAS/SATA HBA   (00AE912)
	N2226 SAS/SATA HBA   (00AE916)


Supported Operating Systems:
OS supported =Windows 16,windows 2019

007.020.014.000 - Moderate Impact
---------------
MR 7.20

Defects:
 Fixed :LSA set lane speed to 16GT/s(DCSG01111833
 LSA : Secured foreign UG Bad drive is not showing Crypto erase option at first, after doing Crypto erase from Storcli & then LSA shows CE option for that UG Bad drive(DCSG01103089
 PSOC6 LSA 7.20: PSOC current and selected version spelling is displayed as "vesrion" during PSOC update(DCSG01137889
 Fixed: allow multiple DG creation(DCSG01074166
 LSA_MR7.20_PA:Multiple PDs and VDs selection is not working.(DCSG01039219
 WebGUIRelease_7.20_PA-007.020.004.000-DCSG01042991: "LSA will generate alerts from events since last clean shutdown" & "Starting Gateway installation of LSIStorageAuthority" has "\n" character.(DCSG01043665
 Drive count is showing "0" always under "other hardware" tab in LSA when user connects Tape drive, however storcli shows it properly(DCSG01093643
 Virtual Drive Capacity GUI issue when Disk Cache Policy selected(DCSG00973715
 LSA:AeroMR_7.20:BGI progress information is displayed on issuing PAUSE command(DCSG01052255
 LSA Reference in MRSA readme for Linux(DCSG01080850
 22B Alpha Tape Drive LSA: Mismatch in sector size displayed in server profile and unconfigured good page.(DCSG01112937
 LSA: WebGUIRelease_7.20_PA-007.020.004.000-DCSG01042991: Email settings should have a check for @.(DCSG01048568
 WG: updating PSOC firmware shows Online firmware update is in progress(DCSG01140787
 22B-PSOC6- LSA shows inappropiate message for wrong PSOC image flash(DCSG01132438
 Fixed: allow >32 drive R10(DCSG01039688
 Update the nginx with the SSL flags(DCSG01071924
 WG_RWC3: RWC3 fails to launch from desktop shortcut(DCSG01027396
 Refresh issue of "Port number" under Manage SAS Storage Link Speed though Tape drive has been removed from the setup.(DCSG01096142
 LSA: PD Crypto Erase failed due to error "Description: This is an OS Drive. Erase cannot be performed"(DCSG01061602
 fixed: Max drives for R00(DCSG01040107
 LSA Server: Microsoft Windows API usage (Release function)(DCSG01015555
 fixed: LSA : Controller critical/need attention message is showing wrongly as it has multiple duplicate entries(DCSG01111618
 LSA_MR_7.20_PA2: "Make JBOD" option is displayed for Foreign drive(DCSG01030118
 LSA : JBOD conversion option is coming for Tape drive if the drive is in UG mode, if user clicks JBOD & it shows failure message with error code 38(DCSG01113102
 LSA-MR7.20:Unable to close message dialog on selecting configured PDs > 32 PDs to 240 PDs under Drive Group Tab> PD Tab(DCSG01044347
 Fixed: timout seen during import(DCSG01033216
 LSA : Controller Drop down menu lists the controller above the drop down menu, due to this controller is not seen sometimes though user clicked the ctrlr drop down menu(DCSG01107334
 LSA : Type is not showing any info in Drives information under server profile for Tape drive, whereas the main page of controller shows the type properly(DCSG01111968
 install SLP from installation source beforr. "before" to be corrected.(DCSG01039227
 LSA : RHEL 8.5 OS is not present in the Linux readme file(DCSG01137293
 LSA : EPAK failed event shown SOH Bad(DCSG01145362
 22B Alpha LSA CFF 440-16i: After PD removal/ insertion other hardware count is displayed as 0 in LSA.(DCSG01130124
 Click on other hardware tab remove/insert drive to controller, observe that other hardware information is not displayed.(DCSG01142250
 Select all is selecting all the drives when the number of drives is more than the selectable drives(DCSG00982356
 22B-PSOC6 -OFU windows shows Imporper message during PSOC flash via LSA(DCSG01128864
 WG: LSA Crashes on trying to flash PSOC from LSA(DCSG01126644
 WebGUIRelease_7.20_PA-007.020.005.000-DCSG01058115: New line is not handled properly in the installation scripts.(DCSG01058946
 LSACommon: Restore users files while upgrading LSA(DCSG01073725
 Fixed: LSA : Health of enclosure is showing as "Unknown" always for good/bad enclosures(DCSG01111545
 7.20 Readme is not having Win 2022 OS in supported OS list, however 7.19 LSA readme has Win 2022 OS(DCSG01105553
 OEM details for Embedded controllers in windows OS(DCSG01075803
 Email settings should not have a check for @.(DCSG01090903
 fixed: Enclosure status is displayed as blank in server profile.(DCSG01111966
 For IT controller tty log file is part of Download Server Report(DCSG00966716
 LSA:AeroMR_7.20PA: Previous configuration BGI is displayed post clear config(DCSG01039961
 LSA-7.20_PA - 007.020.002.000 shows jbod for unsupported MA drives(DCSG01035032
 LSA : If user clicks "connected device" under Manage SAS Storage Link Speed, it is not showing any details when user has Tape drive(DCSG01096124
 discovery issue: When the remote server is down the server is not removed from discovered list(DCSG01030008
 Boca 540-16i: LSA displays enclosure/BP logical ID in reverse order.(DCSG01025576 (Port Of Defect DCSG01028918)
 LSA: Faulty Enclosure state is displayed as optimal in LSA(DCSG01080760 (Port Of Defect DCSG01088781)
 Lib_utils rpm not proper and does not have SSL files bundled for LSA aarch64(DCSG01015405 (Port Of Defect DCSG01016303)
 LSA : Statement needs to be modified under Enable security as it shows "Virtual drives" for IT controller(DCSG01136168 (Port Of Defect DCSG01140911)
 DCSG01109800 (Port Of Defect DCSG01119229)
 LSA: Faulty Enclosure state is displayed as optimal in LSA(DCSG01080760 (Port Of Defect DCSG01088782)
 Rebuild operation not seen on an offline drive with Raid 6 , 5 drives created(DCSG01099765 (Port Of Defect DCSG01102969)
 4K Physical Drive JSON file raw size do not match with value shown in JSON(DCSG01016816 (Port Of Defect DCSG01017165)
 WG: JSON File in the servers and serverdetail log folder shows different port numbers(DCSG01075773 (Port Of Defect DCSG01091661)
 LSA Client: IT Connector status value for the PD is not displayed(DCSG01099751 (Port Of Defect DCSG01105329)
 LSA Server: IT Connector status value for the PD has an issue(DCSG01099750 (Port Of Defect DCSG01099752)
 LSA : Manage SAS storage link speed is not showing one of the connected device behind BP(DCSG01026787 (Port Of Defect DCSG01028684)
 LSA: PD Crypto Erase failed due to error "Description: This is an OS Drive. Erase cannot be performed"(DCSG01061602 (Port Of Defect DCSG01062281)
 Enclosure location is displayed as "unknown" instead of internal/external under enclosure properties in physical device properties(DCSG01080769 (Port Of Defect DCSG01089861)
(DCSG01052255 (Port Of Defect DCSG01052266)
 Shenandoah_Snap5:LSA - Drive Firmware version not reported proper in LSA for an NVME drive(DCSG01123114 (Port Of Defect DCSG01130058)
 LSA Avenger_8.1 : Mutliple snapdump file download is showing action successful message, but files are not downloaded.(DCSG01060164 (Port Of Defect DCSG01068639)
 LSA MR 7.19: LSA crashed on clicking Drives TAB post 240 R0 VD deletion(DCSG01013919 (Port Of Defect DCSG01031302)
 Modify the License (or) copyright year to 2022(DCSG01109800 (Port Of Defect DCSG01109801)
 Enclosure location is displayed as "unknown" instead of internal/external under enclosure properties in physical device properties(DCSG01080769 (Port Of Defect DCSG01086649)
 MR7.19 PA2:LSA-02: "Make JBOD" option is not displayed for Aero MR(MegaRAID 9580-8i8e) & Aero iMR(9540-16i)(DCSG01002945 (Port Of Defect DCSG01018282)
 LSA MR 7.19: LSA crashed on clicking Drives TAB post 240 R0 VD deletion(DCSG01013919 (Port Of Defect DCSG01030620)
 LSACommon: Restore users files while upgrading LSA(DCSG01073725 (Port Of Defect DCSG01091973)
 Boca-540-16i : LSA -BP logical id shown as junk(DCSG01014125 (Port Of Defect DCSG01019750)
 Avenger_WG: As part of negative test, manual discovery of vmware server and login crashes LSA(DCSG01015031 (Port Of Defect DCSG01018410)
 Fixed: Update curl library with secure flags(DCSG00963302 (Port Of Defect DCSG01024511)
	
EnhancementRequests:	
 Update ControllerInfo Structure with PartNumber - API Changes(DCSG01064529
 Enable end user tools to read custom SN - part 2(DCSG00950274
 Enable end user tools to read custom SN - part 2(DCSG00950275
 API change to support PD sanitize operations enhancements(DCSG01070995
 Add control command MFI_OOB_MCTP_CONTROL_EXCEPTION_NO_CMD (0x99) in API(DCSG01065378
 Windows Client Win11 OS Support - MR6.14, SAS3 Phase 16, MR 7.20, SAS3.5 Phase 22 (OS GCA Date - 10/05/2021)(DCSG01043610
 LSA GUI Support for Aero 9560/9580 - Add PSOC6 as Vision Controller(DCSG01077815
 Image change - branding for Intel RAID Web Console 3 (LSA rebranded)(DCSG01008558
 Aero 9560/9580 - Add PSOC6 as Vision Controller(DCSG01075692
 Make offline bundle for LWA and LWM ESXi(DCSG01150074 (Port Of EnhancementRequest DCSG01150081)
 Implimented: TCP/HTTP Fortification(DCSG00436245 (Port Of EnhancementRequest DCSG01147883)
 Windows Client Win11 OS Support - MR6.14, SAS3 Phase 16, MR 7.20, SAS3.5 Phase 22 (OS GCA Date - 10/05/2021)(DCSG01043610 (Port Of EnhancementRequest DCSG01068997)


007.019.006.000 - Moderate Impact
---------------
MR 7.19
-LSA : Able to update different Aero-IT HBA FW file (16i) to different model IT-Aero card (16e).(DCSG00986871)
-LSA MR 7.17: Sorting is not working in the span tab of VD in presence of missing drive..(DCSG00946017 (Port Of Defect DCSG00757915))
-AERO _MR_LSA_7_18:Under Personality management > change behavior mode, "Change " button is disabled even though.(DCSG00960275 (Port Of Defect DCSG00907541)
-Update VMware DCPN cases for ESXi 6.7U3 and ESXi 7.0U2.(DCSG00985708 (Port Of Defect DCSG00950625))
-WG: test email fails with NON-auth login when 'sender email address' is set to anything other than domain "@server.com" for.(DCSG00986188 (Port Of Defect DCSG00940109)
-Drive import is success however the message shows incomplete when importing unlocked drive.(DCSG00988921 (Port Of Defect DCSG00734940))
-LSA reports wrong version for the OS..(DCSG00990503 (Port Of Defect DCSG00990486)


007.017.015.000 - Moderate Impact
---------------

Defects:
-WG: Enclosure connector info in PD properties shown "C0 & C0" instead of "C0 & C1".(DCSG00775146
-WG: Logging in to manage server page and clicking on VMware server for login results in VMware login page refresh indefinitely.(DCSG00397834
-WG: Snapdump not getting downloaded with ARM MR 7.17 LSA.(DCSG00653578
-Invalid Enclosure logical ID is displayed is LSA for enclosure connected to Hialeah 8e controller..(DCSG00967815
-LSA MR 7.17: Modifying VD size is not getting updated , if the VD size is more than the current VD size..(DCSG00718530
-WG: LSA service does not start automatically on reboot on OpenEuler.(DCSG00648374
-HBA not listed with index order under Server Profile.(DCSG00418634
-Remote Server Health status without controller is not proper.(DCSG00528112
-WG: RWC3 Linux supports obsolete SHA1-based ciphersuites.(DCSG00500737
-Ventura_LSA_7.17: Under change behavior mode, "Change " button is enabled even though configuration parameter in unchecked.(DCSG00706331
-LSA : OLH shows lane speed values as Unknown, 2.5GT/s, 5GT/s, 8GT/s for Manage PCIe Storage Interface instead of showing 2.5GT/s, 5GT/s, 8GT/s & 16GT/s.(DCSG00971355
-LSA does not launch on ARM Open Euler : 007.017.008.000 ARM build.(DCSG00905358
-LSA service is stopped, after LWM (option4) installation in Ubuntu 20.04 arm system..(DCSG00506960
-Fixed: Added interface check for appropriate mix policy.(DCSG00706336
-behavior mode values is not being set properly.(DCSG00426348
-change button is not enabled for Behavior params change.(DCSG00426709
-WG: DLL files packaged in monitor folder of ARM LSA installation.(DCSG00706354
-Linux, RHEL 8.3 - Blank screen shown on launching latest LSA.(DCSG00777144
-LSA MR 7.17: Make JBOD option is available for all the UGOOD PDs, even though one of the PD is in drive clear process..(DCSG00775455
-Login page help link is showing blank.(DCSG00548034
-Fixed: updated Build script to change permissions of different file types.(DCSG00776044
-LSA is not allowing user to create more than 2 VDs.(DCSG00726030
-Handle the new event LD_ERASE_POTENTIAL_LEAKAGE in client.(DCSG00776413
-Fixed: enclosure state is to be shown need attention when it is in fault state.(DCSG00965622
-Ventura_LSA_7.17: LSA still displays background processes of VDs(VD init) post clear config from LSA.(DCSG00644476
-Ventura_LSA_7.17: LSA crashes on creating 64th VD.(DCSG00708134
-Warning removal as part of new gcc upgrade..(DCSG00757533
-Fixed: Changing Resource type displays recover option.(DCSG00411317
-Ventura_LSA_7.17: Event ID: 633 is generated on changing VD policy when expansion is in progress.(DCSG00650740
-LSA MR 7.17: LSA has older version of LSA_Lib_Utils packaged..(DCSG00397682
-WG: Power supply details are not shown on clicking "No of Power Supplies" in enclosure properties.(DCSG00544568
-LSA MR 7.17 : When partially degraded VD erase is in progress, Erase option is available in Elements Action instead of Stop Erase.(DCSG00758642
-Fixed: Added security flags to make file to build secure LSA binaries.(DCSG00813569
-Legacy:LSA MR 7.17: Upon clicking on the hostname(administrator/root )drop down for the second time, Remote Server discovery option appears twice..(DCSG00396896
-Fixed: Added security flags to LSA Makefile.(DCSG00814604
-WG: VMware user able to download LSA logs of gateway.(DCSG00384359
-Fixed: added directory wise permission while creating corpus.(DCSG00543670
-WG: Server ID cookie generated after login has "httponly", "secure" and "sameSite" fields empty for RWC3 installation.(DCSG00547995
-LSA Client WG: Power supply details are not shown on clicking "No of Power Supplies" in enclosure properties.(DCSG00549353
-LSAServer - WG: Redhat OS icon shown for OpenEuler OS in remote discovery page and Manual discovery page.(DCSG00735182
-WG: Redhat OS icon shown for OpenEuler OS in remote discovery page and Manual discovery page.(DCSG00652676
-Ventura_LSAMR_7.17:VD initialization progress is displayed on triggering VD expansion..(DCSG00776513
-WG 7.17 PA2: error token 009" seen when LSA downgrade is performed from 7.17 PA2 to 7.16 RC build and complete LSA uninstallation is not successful.(DCSG00434242
-Ventura_LSAMR_7.17: Background process displays previous status information post clear config.(DCSG00830097
-WG: LSA allows providing same Busy port to both Webserver and LSA port, ultimately LSA service fails to start.(DCSG00556924
-LSA MR 7.17: In RLM page After applying/clearing filter, Add Physical drive tab is enabled even though no drives are selected..(DCSG00649177
-LSA shows stale data and failed to refresh topology until LSA service restart.(DCSG00477447 (Port Of Defect DCSG00708193)
-Fixed: state-change isn't updating state of the PD incase of bad to good.(DCSG00834219 (Port Of Defect DCSG00916906)
-LSA : While updating UEFI for 440-16e (Aero-IT), "Image update failed" message is coming and next time it passes.(DCSG00935787 (Port Of Defect DCSG00937166)
-LSA Common: Stale folders still persist in html folder.(DCSG00388225 (Port Of Defect DCSG00394666)
-Fixed: Limit R1 from R6 migration, show when applicable.(DCSG00776529 (Port Of Defect DCSG00960423)
-Fixed: modify virtual drive to show appropriate allowed operation values.(DCSG00433726 (Port Of Defect DCSG00518957)
-WG: Server ID cookie generated after login has "httponly", "secure" and "sameSite" fields empty for RWC3 installation.(DCSG00547995 (Port Of Defect DCSG00654119)
-LSA : PDs are not listing properly after pull/push from enclosure/Backplane.(DCSG00916164 (Port Of Defect DCSG00917749)
-change button is not enabled for Behavior params change.(DCSG00426709 (Port Of Defect DCSG00428813)
-LSA : PDs are not listing properly after pull/push from enclosure/Backplane.(DCSG00916164 (Port Of Defect DCSG00917716)
-Fixed: StateChange Event handled to update repository.(DCSG00555478 (Port Of Defect DCSG00708165)
-Fixed: Corrupt image file leads to LSA crash.(DCSG00951718 (Port Of Defect DCSG00960390)
-LSA displays all lane speed values under Manage PCIe storage interface.(DCSG00547375 (Port Of Defect DCSG00549936)
-Fixed: Parameter 16GT is not visible while updating lane speed.(DCSG00255550 (Port Of Defect DCSG00960305)
-LSA MR 7.18: LSA events shows full description of the behavior mode(Jbod) change instead of mentioning Mode name..(DCSG00913588 (Port Of Defect DCSG00960083)
-LSA allows to upgrade without uninstalling previous version of LSA in Ubuntu 18.04.05.(DCSG00435199 (Port Of Defect DCSG00500750)
Headline:.(DCSG00965622 (Port Of Defect DCSG00980121)
-LSA : RHEL 7.9 , Ubuntu 18.04.5 and ESXi7.0u1 OS are missing in Linux LSA readme file & ESXi7.0u1 OS is missing in Windows LSA Readme file.(DCSG00421344 (Port Of Defect DCSG00506913)
-PH19 Alpha - LSA - HBA listed with incorrect index order under view server profile.(DCSG00930402 (Port Of Defect DCSG00960246)
-LSA Windows installation from CDROM fails - error opening installation log file.(DCSG00944480 (Port Of Defect DCSG00944695)
-Addition of 3rd party licenses into the package.(DCSG00501027 (Port Of Defect DCSG00501331)
-Shenandoah_MRSA:Enclosure Location and Status coming as Unknown in MRSA when Click to download all the Enclosure or Backplane properties.(DCSG00412122 (Port Of Defect DCSG00414363)
-VenturaLSA_7_18: Unable to trigger Fast initialization on VDs.(DCSG00959286 (Port Of Defect DCSG00960876)
-Set PR properties are showing offline VDs and user is able to add those offline VDs for Patrol read operation.(DCSG00906763 (Port Of Defect DCSG00919131)
-Foreign import config shows "Incomplete or non-importable foreign config" for secured VD after unlocking with proper keys.(DCSG00423048 (Port Of Defect DCSG00495341)
-LSA : "Unlock" button is not getting enabled if user copy & paste the LKMS passphrase in the security key text box.(DCSG00923594 (Port Of Defect DCSG00925032)
-21B- LSA allows EKM to LKM migartion & ask for Authentication key.(DCSG00920215 (Port Of Defect DCSG00925030)
-Shenandoah_MRSA : OLH link for MRSA OEM build refers to screenshots of non-OEM build.(DCSG00501038 (Port Of Defect DCSG00519848)
-Aero MR : LSA Channel: Drive connector information not displayed correctly when compared with Storcli output.(DCSG00416118 (Port Of Defect DCSG00416248)
-LSA: PD insertion event display issue.(DCSG00840938 (Port Of Defect DCSG00916909)
-Foreign import config shows "Incomplete or non-importable foreign config" for secured VD after unlocking with proper keys.(DCSG00420399 (Port Of Defect DCSG00421316)
-LSA services not starting after installing LSA on RHEL 8.3.(DCSG00915932 (Port Of Defect DCSG00916838)
-LSA Server: Code refresh based on Security Tool findings.(DCSG00500569 (Port Of Defect DCSG00501486)
-LSA : Manage SAS Storage Link Speed is setting values only for 2 phys out of 4 phys if user sets it from LSA.(DCSG00916870 (Port Of Defect DCSG00944446)
-Fixed: state-change isn't updating state of the PD incase of bad to good.(DCSG00834219 (Port Of Defect DCSG00916893)
-LSA : Enable/Disable SSD caching is not working for all VDs at once if user selected multiple VDs and enabling/disabling SSD cache.(DCSG00409275 (Port Of Defect DCSG00415053)
-LSA MR 7.18: Click to download option is enabled in Download snapdump page, eventhough no files are selected for download..(DCSG00922702 (Port Of Defect DCSG00960272)
-Fixed: Added security flags to LSA Makefile.(DCSG00814604 (Port Of Defect DCSG00816013)
-LSA cursor is actively cycling after failed to import the max (240Lds) LDs reached.(DCSG00921402 (Port Of Defect DCSG00922051)
-Addition of 3rd party licenses into the package.(DCSG00501027 (Port Of Defect DCSG00501332)
-Addition of 3rd party licenses into the package.(DCSG00501027 (Port Of Defect DCSG00554176)
-LSA : Loopback IP address is not coming after restarting LSA service if there is no LAN/NIC card.(DCSG00417564 (Port Of Defect DCSG00421192)
-WG: login to manage server page with readonly access and then login to any VMware system, logout to VMware grants readonly user "Admin" previlige.(DCSG00384343 (Port Of Defect DCSG00401650)

EnhancementRequest:
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00388186
-LSA: Add Event for possibility of incomplete writes on parity VDs with no battery backup (ER: DCSG00229751).(DCSG00735186
-Implimented: TCP/HTTP Fortification.(DCSG00436245
-Enable end user tools to read custom SN.(DCSG00938513
-Aero-Margay Connectivity Solution Integration - MR API.(DCSG00956233
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00394652
-Implimented: Additional error code handled.(DCSG00310385
-update dependent to comply with latest OS support.(DCSG00428823
-Upgradation of dependent component with security flags.(DCSG00427912
-Request IT read Product Name/Model Number for SATA drives so that the Product Name/Model Number is displayed in full + FW Version.(DCSG00371060
-Added support for RHEL 8.3.(DCSG00373404
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00388184
-Upgrade of OpenSLL and its dependent components.(DCSG00404741
-LSA: Short term solution for handling SES cable missing to Atlas.(DCSG00735187
-Update 3rdpartyComponents with latest security flags and review deprecated APIs.(DCSG00553596
-Add OpenEuler OS (20.03 LTS) support on Kunpeng 920 Gen4 ARM for Ventura MR/iMR (Driver Binary, StorCLI, Storelib, LSA).(DCSG00546575
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00388185
-MegaAPI: Add API changes for temporary key escrow (PR: DCSG00428069).(DCSG00935525
-Implimented: TCP/HTTP Fortification.(DCSG00436245 (Port Of EnhancementRequest DCSG00937396)
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00388184 (Port Of EnhancementRequest DCSG00394003)
Headline:.(DCSG00427912 (Port Of EnhancementRequest DCSG00432022)
Headline:.(DCSG00427912 (Port Of EnhancementRequest DCSG00431998)
-Linux: LSA service script improvement.(DCSG00841007 (Port Of EnhancementRequest DCSG00903463)
Headline:.(DCSG00404741 (Port Of EnhancementRequest DCSG00427334)
-Update 3rdpartyComponents with latest security flags and review deprecated APIs.(DCSG00553596 (Port Of EnhancementRequest DCSG00553614)
-Apps Advanced Security Enhancements and updates - part 2.(DCSG00394652 (Port Of EnhancementRequest DCSG00447326)
-Update 3rdpartyComponents with latest security flags and review deprecated APIs.(DCSG00553596 (Port Of EnhancementRequest DCSG00654068)
-LSA: Linux 32 bit binary removal.(DCSG00221416 (Port Of EnhancementRequest DCSG00408188)
-Implimented: TCP/HTTP Fortification.(DCSG00436245 (Port Of EnhancementRequest DCSG00941433)
-Implimented: TCP/HTTP Fortification.(DCSG00436245 (Port Of EnhancementRequest DCSG00937397)
-Added support for RHEL 8.3.(DCSG00373404 (Port Of EnhancementRequest DCSG00428725)


007.016.021.000 - Moderate Impact
---------------

Defects:
-LSA : While updating UEFI for 440-16e (Aero-IT), "Image update failed" message is coming and next time it passes.(DCSG00935787)

Enhancements:
-Update comment for SL_ERR_IR_INVALID_FW_FLASH_IMAGE_NVDATA.(DCSG00936705)

007.016.015.000 - Moderate Impact
---------------
MR 7.16

Defects:
 -Instance validation fails for Manage Server GET (MR 7.14, 7.014.000.000): Schema 32(DCSG00079899)
 -LSA 7.15 WG: "Replace Missing drive" page will not open after clicking and closing "Assign Dedicated hotspare" page.(DCSG00167347)
 -LSA MR 7.16: While Updating the firmware Selected Firmware Version is showing wrong text instead of Firmware Version.(DCSG00359474)
 -LSA WG : Uninstall instructions mentioned in LSA ESXi readme is wrong.(DCSG00126899)
 -LSA 7.14 : Clicking on "Configure" option from server landing page is redirecting to controller info page instead of Advanced config page.(DCSG00125950)
 -Physical drive Serial number info should be populate in LSA(DCSG00321940)
 -Legacy:WG 7.14 PA2: Unconfigured Bad drive count is not updated for Drive tab when Vds are created.(DCSG00092875)
 -WG: Folder structure remains after uninstalling the direct agent on windows(DCSG00347401)
 -WG: RWC3 Ubuntu Linux build (07.016.003.000)loads with http instead of https(DCSG00384392)
 -Fixed: Clear staging directory to allow new downloads(DCSG00127783)
 -Description of the behavior of the "fast initialization" on RWC3 is inaccurate (Intel re-branded LSI Storage Authority/LSA)(DCSG00263417)
 -Current speed under "Manage PCIe storage interface" is showing like 2.5GT, 5GT, 8GT instead of 2.5GT/s, 5GT/s, 8GT/s(DCSG00301958)
 -WG 7.14: Invalid VD capacity displayed while creating AddVD on a hole with invalid number of VDs(DCSG00080851)
 -Select all checkbox needs to be consistent in all the tabs(DCSG00108298)
 -LSA-Missing rebuild when a drive goes offline by physical removal(DCSG00327294)
 -Fixed: check spdm support bit before populating details(DCSG00108070)
 -Aero : MR 7.16 -Channel: Mismatch between LSA and Storcli output for drive firmware version(DCSG00342645)
 -Update the PD size for higher size 4k Drives(DCSG00395158)
 -Fixed: Security node is being populated for non secure drives(DCSG00140174)
 -LSA MR 7.16: Sorting is not available in "JBOD to Unconfigured Good conversion" page.(DCSG00311369)
 -Enable Drive Security has incorrect phrase and incorrect word. Forcing a Offline PD, confirmation message shows incorrect word.(DCSG00358750)
 -MR 7.16 : Aero Channel : LSA: "Virtual Drives" should be printed for message event id= 195 instead of logical drives(DCSG00316205)
 -LSA WG: Wrong tool tip is seen on Apply button, while filtering the drives.(DCSG00074726)
 -reference to Virtual Drive instead of Logical Drive in ReadMe(DCSG00111540)
 -Fixed: secure discovery handling(DCSG00318199)
 -LSA WG: Help(?) icon present in LWA in "Schedule Consistency check" page.(DCSG00129159)
 -LSA WG 7.15 : Add hotspare option is enabled for spanned raid levels, even after creating VD.(DCSG00226412)
 -Fixed: Import certificate with Seal is not working, Seal is not enabled after import.(DCSG00122476)
 -fixed: update switch to be displayed as managed switch(DCSG00140169)
 -LSA WG: LSA is allowing to add virtual drives more than 16, when spandepth is increased/decreased.(DCSG00084397)
 -Voltage sensor values are shown in negative for atlas board(DCSG00151544)
 -LSA Client: Behavior mode parameters is not shown(DCSG00079966)
 -LSA: While creating 64 slice VD on same DG the 10th VD Name creating as VDName_010 instead of VDName_10(DCSG00253718)
 -WG 7.14 : in AERO IT controller, the enclosure serial number is shown blank, Storcli shows NA(DCSG00138884)
 -Legacy: LSA WG: LSA is allowing to change the personality mode of the controller in Non-admin access.(DCSG00083219)
 -WG: no status code is displayed on failure of "start recover" operation(DCSG00105107)
 -LSA _MR :- Error/warning message not displayed when unsupported characters entered for changing drive rate settings(DCSG00134600)
 -WG 7.14: In Physical Drive properties, Multipath field is showing "Yes" for all the drives attached, eventhough drives are not in Mulitpath configuration.(DCSG00092819)
 -7.14 LSA : Update the LSA readme.(DCSG00108916)
 -WG: LSA Does not have filter button in drives tab for IT controller Controller console page(DCSG00138885)
 -LSA MR 7.16: Sorting is not working after clicking on Filter option in RLM page.(DCSG00359695)
 -LSA MR 7.16: Modify Virtual Drive field is disabled after changing the unit value from GB to MB.(DCSG00345377)
 -WG: Instance Validation failed for event History get,( MR 7.14, 7.014.004.000): MR Ventura: JBOD mode(DCSG00129472)
 -LSA 7.15 WG: "Make JBOD" option is available for the drives which are Prepared for removal.(DCSG00212830)
 -VD Read cache policy displayed wrong as RA , whereas detailed VD policy shows correct(DCSG00148244)
 -MR 7.16 :Channel_ LSA: VD property modification ( WT to AWB) event description not in sync with the actual VD property(DCSG00323028)
 -fixed: Recovery of NVME drives(DCSG00104462)
 -WG: Creation of simple configuration with dedicated hotspare, LSA creation notification does not include hotspare in total PDs used in config creation(DCSG00259092)
 -LSA MR 7.15: Add Virtual Drive field is enabled and VD is added for patrol read, even after unselecting all VDs in Set Patrol read page.(DCSG00228853)
 -In server settings page under email tab, in absence of any email id, Test configurartion should be disabled(DCSG00146660)
 -WG: Selected element minor GUI issue in naming convention, LSA continues to show download in progress continuously(DCSG00151401)
 -MR 7.16 : LSA: Logical ID of enclosure is not displayed correctly(DCSG00316050)
 -LSA 7.14: Set adjustable task rate field is not allowing to save the changes.(DCSG00126266)
 -LSA Client : Handle Manual Discovery failure cases(DCSG00098052)
 -Manage PCIE Storage interface does not show any data.(DCSG00340896)
 -Enclosure Location and Status coming as Unknown when Click to download all the Enclosure or Backplane properties(DCSG00412122)
 -Silent installation with default Web server port and default LSA port is failing.(DCSG00092962)
 -LSA MR 7.16: Number of VDs is not getting updated after deleting the first created VD.(DCSG00361755)
 -When selected 6272 KB firmware for update failure seen with message as file is more than 16MB size(DCSG00080838)
 -LSA Conf: Clean and remove unused fields(DCSG00297566)
 - -WG 7.14 : VD expansion more than 100 % is allowed in LSA(DCSG00126745)
 -"The given port is in use the next available port " message seen During every DA installation(DCSG00412121)
 -LSA MR : Replace Missing drive option is available for Non-admin privileges.(DCSG00298090)
 -WG: login to manage server page with readonly access and then login to any VMware system, logout to VMware grants readonly user "Admin" previlige(DCSG00384343)
 -LSA MR 7.16 :Progress bar is not shown for Rebuild and Patrol read operations for Non-admin privileges.(DCSG00347097)
 -WG: Instance Validation failed for Controllers get,( MR 7.14, 7.014.004.000)(DCSG00129470)
 -for IT Controller update firmware radio buttons and text does not have clickable hand icon(DCSG00138887)
 -Fixed: Added remove files after files are zipped for snap dump download(DCSG00085869)
 -Enclosure location coming as "unknown" for UBM3 if you boot the system without any drives connected(DCSG00081762)
 -LSA: Filter options does not list NVMe drives in PD list of controller console page(DCSG00138709)
 -LSA: Modifying VD properties during Multiple VD creation list the VD name as "VDName_00" instead of VDName & Modify VD page does not have hand symbol for help icon(DCSG00354486)
 -LSA7.16_Linux compiler specific changes(DCSG00340258)
 -Non-interactive/silent installation does not have options to install LSA based on EVENT NOTIFICATION CHOCIES.(DCSG00078199)
 -WG MR 7.14 PA: Clear option grayed for an incomplete foreign configuration(DCSG00085818)
 -Version not reflected correctly when we upgrade MRSA in ubuntu(DCSG00404727)
 -In Set patrol read properties page, Unselected VD is also added for Patrol read.(DCSG00259156)
 -LSA read me: Update the Open Source details(DCSG00353259)
 -updation of libfcgi.dll with DYNAMICBASE flag(DCSG00426989)
 -Change button is enabled when no change performed in Change Behavior Mode(DCSG00382779)
 -MR 7.14 PA2: Rescan Under foreign config menu is grayed out after importing foreign Vd.(DCSG00101341)
 -LSA does not display full message, while making an offline drive online of a VD from Server Landing Page.(DCSG00366127)
 -Fixed: lib utils version update(DCSG00360539)
 -LSA uninstallation is failing on HPE(DCSG00164985)
 -VDs of different capacities(MB/GB) is not sorting properly.(DCSG00080102)
 -Cisco M6: Selecting drive after filter is applied Element selection is shown as "Zero".(DCSG00278212)
 -API clarification for large io support(DCSG00307042)
 -WG 7.14 PA2: 'show password' and 'show key' are active for "Pause for password at boot time" under 'change drive security'.(DCSG00108259)
 -WG: making an offline drive online of a VD from server summary page, LSA does not notify regarding the destructive operation.(DCSG00340323)
 -RWC3 windows build (07.014.004.000)loads with http instead of https(DCSG00125606)
 -Shenandoah_MRSA:Error message not proper for Ubad to UGood for a Bad drive(DCSG00092851)
 -LSA WG: Alignment issue in Manage server page.(DCSG00138055)
 -RWC3 windows Header has LSA Storage Authority as product name instead of RAID Web Console 3.(DCSG00125329)
 -Fixed: Added code to change content type which is acceptable to IE(DCSG00138898)
 -LSA MR 7.15 Alpha: Clicking on "modify" icon will enable the Add Virtual Drive field even after creating a VD of full size(DCSG00293914)
 -fixed: changed unit to Byte in case of zero size drives(DCSG00072680)
 -LSA Windows: Usage of nginx 1.18 version which is a stable version(DCSG00324413)
 -Fixed:SPDM configuration page shows as blank In LSA(DCSG00138574)
 -Legacy : LSA WG 7.14: Remove Manage server icon is not placed properly for Manually added ESXi servers in List view.(DCSG00110210)
 -MR 7.16 :Channel_ LSA: Missing warning message when tried to modify PCIe Storage Interface(DCSG00358742)
 -Use NVRAM to save PTB information -- API changes(DCSG00082981)
 -When heavy IOs active, LSA is taking very long time to download server report .(DCSG00092899)
 -MRSA Desktop icon should not be present for Ubuntu as per the Read me(DCSG00099517)
 -WG 7.14 PA2: LSA installation on Ubuntu, fails with error "LSA_lib_utils" : Gateway can not be launched(DCSG00089795)
 -Manage server page throws error message "400:" for invalid credentials.(DCSG00136334)
 -WG 7.14 PA2: Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 7.8(DCSG00092841)
 -WG: LSA fails to create Drive group for Non-span depth supported Raid volumes.(DCSG00089810)
 -x Readme needs some modification on supported OS and reference as MRSA in some places(DCSG00146624)
 -WG: Sorting is not working as expected in drives tab with multiple spans. with a span having a missing drive(DCSG00341095)
 -LSA Windows x64: Some of the OS is having an issue(DCSG00307418)
 -LSA MR 7.16: Sorting based on Drivegroup is not proper in Assign dedicated hotspare page.(DCSG00322767)
 -Launchpad on desktop of Rhel 7.7 is shown as "LaunchLSA" instead of "LaunchMRSA"(DCSG00072655)
 -LSA shows FW update failure message even after FW update is successfull.(DCSG00082492)
 -LSA 7.15 WG: Sorting based on Drive group capacity is not proper in "Assign Dedicated hot spare" page.(DCSG00166089)
 -Update credits files in client credits(DCSG00353889)
 -Shenandoah_MRSA:Event description blank for 628,629 in MRSA(DCSG00325879)
 -Fixed: Monitor Conf files are missing write permission(DCSG00129770)
 -Fixed: Spanned drive min vd check calculation error(DCSG00138063)
 -Update Credits.html with updated licenses(DCSG00428654)
 -LSA MR 7.15 : LSA does not show message while modifying Disk cache policy of VD in Advanced configuration page.(DCSG00263699)
 -Upgrade is not working in ubuntu from 7.15 to 7.16 packages(DCSG00315134)
 -LSA : Loopback IP address is not coming after restarting LSA service if there is no LAN/NIC card(DCSG00417564)
 -MR controller with No Alram is not auto refreshing on changing the controller properties(DCSG00124484)
 -On ARM server, on every reboot LSA services are stopped: Ubuntu 18.04(DCSG00105871)
 -displays 0 Needs attention when we have degraded LDs(DCSG00092831)
 -WG 7.14 : Mismatch seen in the total number of available UG drives and actual no of PDs in PD list during encrypted R60 VD creation.(DCSG00134663)
 -LSA - Set PR properties is showing VD as optimal though it is offline or degraded(DCSG00226300)
 -Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 8.2(DCSG00115253)
 -Fixed: updated Readme with "Health status shown in LSA is as per LSA's health algorithm."(DCSG00412125)
 -LSA MR 7.16: Changing the lane speed in Manage PCIe storage interface page is showing Operation is either not allowed or not supported, whereas storcli shows Success reboot required(DCSG00397804)
 -WG: ""Your connection is not Private" shown twice in "Manage server page"(DCSG00391486)
 -Legacy : WG: LSA auto logs in on clicking "verify" button for "Managed" VMware manually added server in managed server page(DCSG00112178)
 -Fixed: updated nginx and libcurl(DCSG00414394)
 -WG: Sorting does not work in Span tab of VD in presence of missing drive(DCSG00258267)
 -Fixed: Build script changes to pick up the latest conf and ini files(DCSG00125997)
 -SSD WearGuage Estimated Life Remaining in Percent as "N/A" for New Drives(DCSG00074664
 -Fixed: Certificate Algorithm details are showing blank for few certificate slots.(DCSG00123069)
 -LSA fails to import R0 which has pinned cache after a reboot(DCSG00356398)
 -WG: instance validation failed for controllers Operations GET: iMR Ventura : Schema 34: MR 7.16(DCSG00342339)
 -LSA service fails to start when LSA port value is set to 2463(DCSG00083383)
 -Secured foreign locked VDs details are not displayed under foreign configuration to import/clear foreign config(DCSG00103239)
 -LSA Server: WG MR 7.14 PA2: Advance configuration page is in hung state in presence of jbod drive and prepare for removal state(DCSG00114253)
 -Fixed: Invalidate certificate slot is failing with error code 165.(DCSG00122448)
 -LSA WG: Non-span depth supported raid levels are showing "Span depth modify" option in Advanced config page upon clicking on "Compare and select" link.(DCSG00143503)
 -LSA MR 7.15 Alpha: Changing the number of spans while creating DG shows wrong info about the Number of VDs can be added to DG.(DCSG00264033)
 -LWA Compilation Issue Resolution(DCSG00228825)
 -Only the text in "Start recover" operation for bad NVMe drive is clickable(both CC and ss Page), GUI issue on expanding the controller health(DCSG00105108)
 -LSA WG: In Advanced configuration page, hotspare PD adding page disappears when users scrolls up/down the LSA page.(DCSG00080074)
 -MR7.15 LSA Client: Unsupported icon in Server and Controller Dashboard(DCSG00277830)
 -WG: No success or failure icon is shown on silencing alarm, hand symbol is not present for close icons in advanced enclosure properties(DCSG00255201)
 -WG: nginx conf file after installing DA is empty. unable to manage the DA from Gateway though DA LSA service running(DCSG00383999)
 -Clear configuration is success when JBOD has OS(DCSG00382535)
 -LSA Server: Hard coded string over disk and controller implementation(DCSG00152933)
 -Enclosure Name not correct for x4 Backplanes Connected via Straight cables to two controllers.(DCSG00315377)
 -WG: Instance Validation failed for servers get,( MR 7.14, 7.014.004.000)(DCSG00129468)
 -PH15 LSA IT:In RHEL7.8 for enclosure drives Multi path field is showing as"Yes" In Physical Drive properties,without Multipath configuration(DCSG00132726)
 -Shenandoah: MRSA: VD reference in modify LD property ( try to change disk cache and the help balloon refers to VD)(DCSG00324759)
 -SPDM_LSA : There is no successful message displayed for the export CSR action.(DCSG00122457)
 -Memory Leak issues LSA Build(DCSG00149688)
 -Port Box Bay info incorrect for ISE operation page(DCSG00092895)
 -The "More Actions" menu doesn't open up when the RAID controller is ESRT2(DCSG00259353)
 -Enclosure Bay count coming Wrong in(DCSG00074661)
 -Updated Arm read me file with arm specific changes(DCSG00085797)
 -LSA Property: package version mismatch between components in IT(DCSG00307461)
 -Test Configuration button should be disabled till we get the response(DCSG00299771)
 -LSA Client: WG MR 7.14 PA2: Advance configuration page is in hung state in presence of jbod drive and prepare for removal state(DCSG00129756)
 -LSA MR 7.16: Not able to modify the VD size in Advanced configuration page.(DCSG00381677)
 -multi-LUN tool support for multi-actuator drives.(DCSG00122386)
 -Shenandoah_MRSA : Number of hours is wrong in MRSA evetns for Event 544(DCSG00325891)
 -LSA Client: Manage Link Speed not showing the error message(DCSG00310339)
 -Manual Discovery failure shouldn't return HTTP status:200(DCSG00098024)
 -LSA Common: Package 64 bit monitor libraries as part of Windows x64 package(DCSG00307031)
 -Shenandoah_MRSA: Enclosure Type in Server profile is not complete. Needs to allign with CLI(DCSG00081768)
 -LSA: MR-7.14-SPDM tab needs correction.(DCSG00108295)
 -LSA: "Incorrect Connector Name" under physical drive properties.(DCSG00358747)
 -LSA Common: Stale folders still persist in html folder(DCSG00388225)
 -fixed: import of certificate issue(DCSG00094369)
 -Not able to launch MRSA though the launch icon or installer(DCSG00078194)
 -LSA MR 7.15 Alpha : Schedule consistency Check field is showing partially degraded VD as optimal.(DCSG00263547)
 -Event strings not proper in MRSA for 379,383,385(DCSG00325883)
 -Junk characters are getting displayed in enclosure information with no drives connected.(DCSG00074730)
 -LSA MR 7.16: Filter option is not working properly in RLM page.(DCSG00342455)
 -PCI-Switch subtype when enclosure is an pci-switch(DCSG00085935)
 -Predicitive Failure count and Drive temperature not getting updated in PD property page(DCSG00082823)
 -Windows OS crashes after upgrading to LSA 007.014.005.000(DCSG00138044)
 -Shenandoah_MRSA: Controller Drop down not listing all controllers(DCSG00108923)
 -LSA - ICX - Lane speed under Manage PCIe storage interface is showing like 2.5GT, 5GT, 8GT instead of 2.5GT/s, 5GT/s, 8GT/s(DCSG00259499)
 -fixed: Min VD size check for R1 was missing(DCSG00086324)
 -fixed: MFI code stops LSA from showing slot 0 and 1 when it is not configured(DCSG00123067
 -WG 7.14 PA:During the Creation of r60 vd , removal/adding drives creates inconsistency in AddPhysicalDrive and Addhotspare tables.(DCSG00079935)
 -"Compare and Select" page shows Raid 6 with 3 drives(DCSG00087244)
 -Current speed under "Manage SAS storage link speed" is showing like 3Gb, 6Gb, 12Gb instead of 3Gb/s, 6Gb/s, 12Gb/s(DCSG00301640)
 -Drives connected to IT controller reports Shield Counter(DCSG00264740)
 -WG: RWC3 windows build loads with http, instead of https(DCSG00340881)
 -WG 7.14 PA2: Stripe size under DG does not sort properly when multiple Vds are created with different strip sizes.(DCSG00093774)
 -LSA_SPDM : Import certificate chain event id 622 description is not proper.(DCSG00122482)
 -WG MR 7.14 PA1: LSA allows to select 512B drives as DHSP for 4K DG(DCSG00078853)
 -Backplane info is not proper in expanded state(DCSG00106485)
 -Shenandoah_MRSA : Transport feature needs to be removed from array properties(DCSG00081965)
 -Fixed: update approved user list(DCSG00384488)
 -Fixed: Import certificate /Download CSR options are disabled for slot 0 & 1(DCSG00138892)
 -Aero MR : LSA Channel: Drive connector information not displayed correctly when compared with Storcli output(DCSG00416118)
 -Fixed: changed values to comply with schema restrictions(DCSG00140179)
 -LSA WG : LSA "Download Diagonstic" field is not downloading the ttylog in Readonly access.(DCSG00083816)
 -LSA - Error code 169 - Description Shows as Blank.(DCSG00111872)
 -Credits page needs an update(DCSG00232932)
 -WG:LWA:Not all snapdump logs are downloaded on trying to download all the generated snapdump logs(DCSG00216125)
 -MR 7.16 Aero: Storcli displays Enclosure Serial Number as blank whereas LSA shows as "N/A"(DCSG00316066)
 -Fixed: permission of only last node in path was changing(DCSG00384372)
 -After the upgrade or trying to delete through RPM launch Icon is not deleted(DCSG00078205)
 -Fixed: issue resolution message for non-recoverable drive(DCSG00105032)
 -Port information is wrong when SAS drive is connected to UBM3 BP with 416A controller(DCSG00316863)
 -Fixed: enclosure type and subtype display changes for PCI-switch(DCSG00314948)
 -Remove the individual elements download from MRSA(DCSG00418470)
 -WG: LSA does not allow to change to any other behavior once encountering error during behavior change : GUI Change(DCSG00255157)
 -MR 7.15: LSA fails to launch in Ubuntu.(DCSG00221326)
 -JBOD creation is not allowed through MRSA both on windows and Linux on 7.16 builds(DCSG00317915)
 -Shenandoah_MRSA:Enclosure type not correct for UBM4 backplanes in server profile(DCSG00360535)
 -WG MR 7.16 : Direct agent and standalone does not load on Ubuntu ARM system.(DCSG00395624)
 -Spacing issues on securing a DG as secure, minor GUI issue non notification of enabling scsiUnmap(DCSG00138886)
 -Unable to uninstall the RWC3 on Ubuntu 20.4 when xterm present(DCSG00146748)
 -WG 7.14:During VD creation filtering 4k drives displays blank PD table when mixing is not allowed(DCSG00078974)
 -WG 7.14 PA2: "Unlock" button should be grayed out for Foreign secured locked PD.(DCSG00094756)
 -LSA MR 7.16: Inconsistency while upgrading the LSA.(DCSG00417467)
 -Shenandoah_MRSA: Virtual disk reference in " Make Drive Online" option(DCSG00306847)
 -LSA MR 7.15: Not able to remove the manually added servers.(DCSG00239878)
 -Legacy: LSA WG: In home page, Scroll up option is missing when user expands the Server profile.(DCSG00083860)
 -MR Controller Downloaded Diagnostic Data has Deviceid set to 0 in line number 12(DCSG00125594)
 -fixed: R1 migration form R0 with one UG-good PD(DCSG00312113)
 -WG: RWC3 Ubuntu Linux build shows LSA instead of RWC3 during installation.(DCSG00385902)
 -Foreign import config shows "Incomplete or non-importable foreign config" for secured VD after unlocking with proper keys(DCSG00420399)
 -LSA MR 7.16: VD is expanded to 100%, when user provide the expansion percentage value between 0.1 to 0.5(DCSG00303650)
 -Legacy WG: Verify Credentials of the manually discovered server in Manage server page does not check if server is down(DCSG00080854)
 -Uninstall the RWC3 does not remove the complete folder structure(DCSG00125612)
 -WG: empty enclosure ID and slot ID is displayed for NVMe initialization event in event logs(DCSG00105113)
 -SAS address is shown for PCIe (NVME) drives instead of WWID(DCSG00138744)
 -Health status changes of the remote server does not get updated in the gateway remote discovery page(DCSG00086628)
 -Shenandoah: MRSA events for enclosure insertion not in sync with firmware logs(DCSG00303613)
 -LSA is showing wrong "LSA_lib_utils" version while uninstalling in linux.(DCSG00083760)
 -WG 7.14 PA2:managed server icon for self server is shown "add" in manage server page if we add ubuntu/ any server to manage server list.(DCSG00112829)
 -WG: Instance validation fails for Configuration service GET, LSA build : MR 7.14, 7.014.000.000(DCSG00079959)
 -LSA MR 7.15: Reload option should not be available in Remote discovery page.(DCSG00235388)
 -Shenandoah: MRSA: keyType information wrong in MRSA for event 343(DCSG00333167)
 -Whitley ICX : LSA - Add physical drives option is not coming for user when trying to recon from R6 to R0(DCSG00104470 (Port Of Defect DCSG00105105)
 -7.14: Update read me files(DCSG00221381 (Port Of Defect DCSG00226031)
 -Handling Manual Discovery ADD case(DCSG00077625 (Port Of Defect DCSG00101928)
 -behavior mode values is not being set properly(DCSG00426348 (Port Of Defect DCSG00426351)
 -AV_RAID_MODE:Missing drive info not displayed when performed on PDs of multiple DGs(DCSG00411847 (Port Of Defect DCSG00415015)
 -LSA_Server: Mismatch in "disk cache policy" during VD creation and after VD creation(DCSG00404783 (Port Of Defect DCSG00408997)
 -LSA uninstallation is failing on HPE(DCSG00164985 (Port Of Defect DCSG00164991)
 -"delete config" command clears the config, when OS/FS in the drive without "force" option.(DCSG00077464 (Port Of Defect DCSG00101933)
 -WG: Instance validation fails for PHY's GET and phy/0 GET (MR 7.13, 7.013.004.000)(DCSG00066942 (Port Of Defect DCSG00078972)
 -CSET Port of Defect DCSG00078494: Lone LF in body of email message(DCSG00078494 (Port Of Defect DCSG00078973)
 -Connected device under "Manage PCIe storage interface" is not showing any NVMe drive details(DCSG00302010 (Port Of Defect DCSG00314950)
 -Fixed: updated configured PD to include offline and failed drives(DCSG00382593 (Port Of Defect DCSG00404817)
 -WG: Manually added VMware server continues to show and does not get auto discovered.(DCSG00243976 (Port Of Defect DCSG00312021)
 -LSA : Modify properties option is not coming to user for CC VD using 730-8i controller(DCSG00408495 (Port Of Defect DCSG00415046)
 -Fixed: Parameter 16GT is not visible while updating lane speed(DCSG00255550 (Port Of Defect DCSG00421350)
 -LSA Server: Manual discovery fix(DCSG00246091 (Port Of Defect DCSG00312023)
 -WG: VMware user able to download LSA logs of gateway(DCSG00384359 (Port Of Defect DCSG00395338)
 -LSA Conf: Clean and remove unused fields(DCSG00297566 (Port Of Defect DCSG00347725)
 -On ARM server, on every reboot LSA services are stopped: Ubuntu 18.04(DCSG00105871 (Port Of Defect DCSG00137404)
 -update HBA 440-16i UEFI BSD failed via LSA(DCSG00074275 (Port Of Defect DCSG00101747)
 -LSA Client: Manage Link Speed not showing the error message(DCSG00310339 (Port Of Defect DCSG00310340)
 -Changing the ngroups list values(DCSG00102619 (Port Of Defect DCSG00103258)
 -LSA Property: package version mismatch between components in IT(DCSG00307419 (Port Of Defect DCSG00312026)
 -LSA Client: WG MR 7.14 PA2: Advance configuration page is in hung state in presence of jbod drive and prepare for removal state(DCSG00129756 (Port Of Defect DCSG00152277)
 -LSA_Avenger: Modify VD properties page is not opening, when VD is created from Simple configuration.(DCSG00337910 (Port Of Defect DCSG00345130)
 -LSA Avenger: Sorting based on VD capacity is not working when VD with size more than 1 TB is present in DG(DCSG00321981 (Port Of Defect DCSG00335909)
 -LSA Advanced Configuration does not work with controller is with RAID mode , Personality behavior=RAID-0(DCSG00063716 (Port Of Defect DCSG00065591)
 -LSA_Avenger: filtering and then sorting drives which are used in vd creation , drives table goes blank.(DCSG00354629 (Port Of Defect DCSG00363767)
 -LSA : Enable/Disable SSD caching is not working for all VDs at once if user selected multiple VDs and enabling/disabling SSD cache(DCSG00409275 (Port Of Defect DCSG00415052)
 -LSA report Power supply status only after LSA service restart(DCSG00086465 (Port Of Defect DCSG00102025)
 -PH15 LSA IT:In RHEL7.8 for enclosure drives Multi path field is showing as"Yes" In Physical Drive properties,without Multipath configuration(DCSG00132726 (Port Of Defect DCSG00138842)
 -MR7.15 Alpha (DBU) WG: unable to change the behavior mode to "none" on Aero controller(DCSG00278399 (Port Of Defect DCSG00312025)
 -CSET Port of Defect DCSG00355995: LSA imports all foreign configs while importing 240VDs, but it shows error message "The server could not import foreign configurations" (Error Code:2)(DCSG00355995 (Port Of Defect DCSG00395255)
 -Cisco - CSCvv26000: C240 M6 : Improper display of RAID5 VD size while creating VD through LSA in Zuma beach(DCSG00313412 (Port Of Defect DCSG00325945)
 -LSA- ICX : Profile properties shows that WB volumes support as "False" under controller Info(DCSG00254886 (Port Of Defect DCSG00278008)
 -MR 7.15 - LSA Event Log is showing Default Read Policy as Always Read Ahead ...needed to be "Read Ahead" instead(DCSG00299006 (Port Of Defect DCSG00307816)
 -Fixed: updated nginx and libcurl(DCSG00414394 (Port Of Defect DCSG00419679)
 -Shenandoah_MRSA: Controller Drop down not listing all controllers(DCSG00108923 (Port Of Defect DCSG00110220)
 -LSA Client : Handle Manual Discovery failure cases(DCSG00098052 (Port Of Defect DCSG00112023)
 -ICX_Whitley_Orion: LSA- Link speed details are not showing properly for Tape drive in WebGUI(DCSG00075777 (Port Of Defect DCSG00102597)
 -Manual discovery page gets hung while adding the server to Auto discovery list.(DCSG00080451 (Port Of Defect DCSG00102024)
 -WG:LSA provides controller operation option of starting patrol read when there are only raid 1 VDs created using NMVe PD's(DCSG00257688 (Port Of Defect DCSG00312024)
 -RWC3 for Windows breaks when testing email on SMTP Port 587(DCSG00298491 (Port Of Defect DCSG00307805)

EnhancementRequest:
 -LSA credits page update with latest open source components(DCSG00074643)
 -LSA Client: NVMe Drive Init failure Error Reporting(DCSG00085790)
 -LSA Server: NVMe Drive Repair - Handling Event(DCSG00086254)
 -Added the current Speed Column to phy and lane speed table(DCSG00075198)
 -MegaAPI: Add API changes for Support Parity Read Cache Bypass (PR: DCSG00245039)(DCSG00370441)
 -MR API: Change event class for SPDM events(DCSG00134416)
 -API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI STAT(DCSG00222915)
 -LSA_Server: Fetch and Display Port name and Box number for NVMe drives with Init error/repair(DCSG00373455)
 -Update X-Content-Type-Options to Header(DCSG00342485)
 -LSA changes to implement the PR:DCSG00152043(DCSG00216430)
 -Restore Factory Default doesn't prompt user to reboot the system after being performed(DCSG00120443)
 -(DCSG00082479)
 -MR7 - LSA_Common: Support WJ Pinning for both WB and WT Parity RAID VDs(DCSG00214470)
 -API change to add connector index as part of NVMe Init Error drive information(DCSG00352896)
 -SPDM support changes(DCSG00092939)
 -LSA 64bit support - disconnect 32 bit(DCSG00243701)
 -Update Nginx Settings and allow download server report for admin users(DCSG00347344)
 -MegaAPI: Add Event for possibility of incomplete writes on parity VDs with no battery backup (ER: DCSG00229751)(DCSG00405671)
 -Support for Ubuntu v18.04 OS(DCSG00081316)
 -MFI SMP Port Num API changes(DCSG00257777)
 -Upgrade of OpenSLP source Code(DCSG00167228)
 -Warning events including Predictive failure (code 96) to add the new property to the drive(DCSG00074191)
 -Cleaning up LSA Readme file(DCSG00086337)
 -Major version upgrade of OpenSSL(DCSG00075194)
 -LSA Common: Enhance OEM build generation on Standalone server(DCSG00138907)
 -MR7.15: LSA - Linux 32 bit binary removal in Standalone Environment(DCSG00228734)
 -LSA Server: Enhance development environment to maintain OEM specific projects(DCSG00129446)
 -Add new security events(DCSG00167313)
 -Multi path Display Enhancement in the Client(DCSG00075193)
 -LSA_7.16: Enhance Make Release process(DCSG00339979)
 -Enhance LightWeightMonitor build process(DCSG00093307)
 -MR API: create a new DCMD for BMC to initiate an expander reset(DCSG00362825)
 -SMART Polling Improvement- API Changes(DCSG00214352)
 -LSA MR7.16: Ruby SED Support(DCSG00265657)
 -storcli does not show the SAS Address of the enclosure(DCSG00255107)
 -MR API: reclassify MR_EVT_CTRL_FW_VALID_SNAPDUMP_AVAILABLE as informational(DCSG00292323)
 -Eliminate reporting of capacitance over 100%(DCSG00149664)
 -Shenandoah: Reverting back the changes made for Span setting for RAID 1 & 10(DCSG00074194)
 -Updated 3rd party libs(DCSG00286594)
 -New MFI Stat for the updated recon behavior(DCSG00229416)
 -MegaAPI: rename WJ events and change event messages (PR: DCSG00166915)(DCSG00332867)
 -MegaAPI: Add API changes for Support WJ Pinning for both WB and WT Parity RAID VDs (PR: DCSG00166915)(DCSG00312334)
 -NVME Failed drive error reporting(DCSG00085936)
 -System Health Status update in case of multiple controllers present in system.(DCSG00075224)
 -(DCSG00082474)
 -MR7 API: Add package incompatibility reporting(DCSG00231443)
 -MegaAPI: Add API Controller Properties and MFCD for ParityReadCacheBypass (PR: DCSG00237022)(DCSG00282676)
 -Manual Discovery Enhancements(DCSG00149397)
 -SPDM Support for Aero in LSA GUI(DCSG00076958)
 -Script build process for arm and esxi LSA(DCSG00075216)
 -LSA 64bit support - disconnect 32 bit(DCSG00243703)
 -Additional NameSpace behavior changes(DCSG00383671)
 -Add the Force Refresh for Cache module in LSA(DCSG00219527)
 -SMART Polling Improvement - API Changes(DCSG00246317)
 -To add return status MFI_STAT_OK_REBOOT_REQUIRED to MR_DCMD_LD_SET_PROPERTIES in mr.h(DCSG00256271)
 -Additional FDE type for Ruby SED support(DCSG00055878)
 -LSA Client: NVMe Drive Repair(DCSG00085927)
 -Build Enhancement - Automate standalone build generation(DCSG00075220)
 -Populating port name of a UBM U.2/3 backplane with NVMe drives(DCSG00132390)
 -MR_SAS_PHY_LINK_SPEED should indicate that the link is not active(DCSG00073569)
 -MR7.16 - LSA Server: SAS Address and LogicalID fields missing in enclosure properties(DCSG00255108)
 -Optimize Server Report Generation(DCSG00351905)
 -LSAServer: Add the Force Refresh for Cache module in LSA(DCSG00218902)
 -Convert LSA installation scripts from csh to sh(DCSG00075219)
 -Remove bays on port for Shenandoah For MRSA(DCSG00101417)
 -LSA Common: NVMe Drive Repair - Event and MFI state notification(DCSG00086253)
 -Multi path Enhancement in the server(DCSG00071167)
 -Upgrade the Install Shield Version to 2020(DCSG00219077)
 -Optimize LSA Server code Compilation Time(DCSG00075222)
 -LSA Server: Autoconfig API Improvement(DCSG00212945)
 -Upgrade GWT from 2.8.1 to 2.8.2(DCSG00110240)
 -LSA Server: NVMe Drive Repair(DCSG00085947)
 -Enhance Standalone RWC3 build process(DCSG00124860)
 -API changes to expose MR_AUTO_CFG_PARAMETER for NONE mode(DCSG00151058)
 -Request to add checks (DevId, SubDevice Id) check prior to flashing(DCSG00396121)
 -Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API(DCSG00226286)
 -(DCSG00152596)
 -Implemented: setting appropriate permission for files and directories(DCSG00351962)
 -LSA needs to add the new adapter name to the support matrix hence marking it to Small to update the support matrix in readme(DCSG00075062)
 -Upgrade of OpenSLL and its dependent components(DCSG00124493)
 -LSA Client - Optimize Client Compilation Time(DCSG00075225)
 -MR7 : Support WJ Pinning for both WB and WT Parity RAID VDs(DCSG00214471)
 -API change to replace enum declaration with U32.(DCSG00393987)
 -API changes for reporting missing cables(DCSG00313199)
 -Changes to support 16port connection to Expander with AeroIOC(DCSG00254845)
 -MR 7.16: Make environment to generate MRMON 64 bit libraries(DCSG00308331)
 -MR API changes - Support new Provisional bit in CTRL INFO and new MFI status for Platform Security SPDM(DCSG00106380)
 -Updated 3rd party libs(DCSG00286594 (Port Of EnhancementRequest DCSG00384441)
 -LSA_Server: Display Write Cache Settings for PD(DCSG00366367 (Port Of EnhancementRequest DCSG00373491)
 -Update Nginx Settings and allow download server report for admin users(DCSG00347344 (Port Of EnhancementRequest DCSG00354847)
 -Updated 3rd party libs(DCSG00286594 (Port Of EnhancementRequest DCSG00306730)
 -LSA Server: RRB141 - Ensure that the SSD cache policy is changeable and the status information is correct(DCSG00171246 (Port Of EnhancementRequest DCSG00228742)
 -Optimize Server Report Generation(DCSG00351905 (Port Of EnhancementRequest DCSG00384509)
 -(DCSG00167228 (Port Of EnhancementRequest DCSG00167257)
 -LSAServer: Add the Force Refresh for Cache module in LSA(DCSG00218902 (Port Of EnhancementRequest DCSG00225933)
 -Crypto Erase option for Cryptographic Capable Drive(DCSG00373462 (Port Of EnhancementRequest DCSG00384657)
 -LSA: Linux 32 bit binary removal(DCSG00221416 (Port Of EnhancementRequest DCSG00363675)
 -Linux: Installer script improvement(DCSG00130050 (Port Of EnhancementRequest DCSG00230033)
 -Implemented: setting appropriate permission for files and directories(DCSG00351962 (Port Of EnhancementRequest DCSG00384472)
 -LSA_Common: Fetch and Display Port name and Box number for NVMe drives with Init error/repair(DCSG00373455 (Port Of EnhancementRequest DCSG00373474)
 -Update X-Content-Type-Options to Header(DCSG00342485 (Port Of EnhancementRequest DCSG00384513)
 -(DCSG00075222 (Port Of EnhancementRequest DCSG00081005)
 -(DCSG00098812 (Port Of EnhancementRequest DCSG00105863)
 -LSA: Linux 32 bit binary removal(DCSG00221416 (Port Of EnhancementRequest DCSG00408121)
 -SPDM support changes(DCSG00092939 (Port Of EnhancementRequest DCSG00113254)
 -BST Automation for LSA(DCSG00098812 (Port Of EnhancementRequest DCSG00218817)
 -Implemented: setting appropriate permission for files and directories(DCSG00351962 (Port Of EnhancementRequest DCSG00354907)
 -CSET Port of EnhancementRequest DCSG00075194: Major version upgrade of OpenSSL(DCSG00075194 (Port Of EnhancementRequest DCSG00083924)
 -MR7.15: LSA - Linux 32 bit binary removal in Standalone Environment(DCSG00228734 (Port Of EnhancementRequest DCSG00293989)
 -Update X-Content-Type-Options to Header(DCSG00342485 (Port Of EnhancementRequest DCSG00348015)
 -CSET Port of EnhancementRequest DCSG00075194: Major version upgrade of OpenSSL(DCSG00075194 (Port Of EnhancementRequest DCSG00083925)
 -Added support for RHEL 8.3(DCSG00373404 (Port Of EnhancementRequest DCSG00428563)
 -(DCSG00096553 (Port Of EnhancementRequest DCSG00110100)
 -(DCSG00085947 (Port Of EnhancementRequest DCSG00086469)
 -(DCSG00286594 (Port Of EnhancementRequest DCSG00290207)
 -Update Nginx Settings and allow download server report for admin users(DCSG00347344 (Port Of EnhancementRequest DCSG00384205)
 -Update Nginx Settings and allow download server report for admin users(DCSG00347344 (Port Of EnhancementRequest DCSG00384206)
 -Implemented: setting appropriate permission for files and directories(DCSG00351962 (Port Of EnhancementRequest DCSG00385127)
 -Ensure that the SSD cache policy is changeable and the status information is correct(DCSG00214163 (Port Of EnhancementRequest DCSG00230031)
 -Optimize Server Report Generation(DCSG00351905 (Port Of EnhancementRequest DCSG00384499)
 -(DCSG00286594 (Port Of EnhancementRequest DCSG00286739)
 -LSA_client: Display Write Cache Settings for PD(DCSG00372331 (Port Of EnhancementRequest DCSG00383405)
 -Added support for RHEL 8.3(DCSG00373404 (Port Of EnhancementRequest DCSG00428561)
 -Optimize Server Report Generation(DCSG00351905 (Port Of EnhancementRequest DCSG00366266)
 -Crypto Erase option for Cryptographic Capable Drive(DCSG00369727 (Port Of EnhancementRequest DCSG00384592)
 -WebGUI: Automate the test cases specific to MR7.14 Product Requirements(DCSG00082499 (Port Of EnhancementRequest DCSG00086646)
 -Update X-Content-Type-Options to Header(DCSG00342485 (Port Of EnhancementRequest DCSG00384514)


007.013.016.000 - Moderate Impact
---------------
MR 7.13

Defects:
-Legacy WG: Verify Credentials of the manually discovered server in Manage server page does not check if server is down.(DCSG00112141 (Port Of Defect DCSG00080854))
-Legacy : WG: LSA auto logs in on clicking "verify" button for "Managed" VMware manually added server in managed server page.(DCSG00112744 (Port Of Defect DCSG00112178))
-MR controller with No Alram is not auto refreshing on changing the controller properties.(DCSG00124768 (Port Of Defect DCSG00124484))
-LSA _MR :- Error/warning message not displayed when unsupported characters entered for changing drive rate settings.(DCSG00136282 (Port Of Defect DCSG00134600))
-LSA Server: WG MR 7.14 PA2: Advance configuration page is in hung state in presence of jbod drive and prepare for removal state.(DCSG00219183 (Port Of Defect DCSG00114253))
-LSA WG : LSA "Download Diagonstic" field is not downloading the ttylog in Readonly access..(DCSG00219184 (Port Of Defect DCSG00083816))
-Secured foreign locked VDs details are not displayed under foreign configuration to import/clear foreign config.(DCSG00221295 (Port Of Defect DCSG00103239))
-Credits page needs an update.(DCSG00233292 (Port Of Defect DCSG00232932))
-WG 7.14 PA2: Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 7.8.(DCSG00233700 (Port Of Defect DCSG00092841))
-On ARM server, on every reboot LSA services are stopped: Ubuntu 18.04.(DCSG00233701 (Port Of Defect DCSG00105871))
-Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 8.2.(DCSG00233702 (Port Of Defect DCSG00115253))
-MR Controller Downloaded Diagnostic Data has Deviceid set to 0 in line number 12.(DCSG00233703 (Port Of Defect DCSG00125594))
-LSA 7.14 : Clicking on "Configure" option from server landing page is redirecting to controller info page instead of Advanced config page..(DCSG00233704 (Port Of Defect DCSG00125950))
-fixed: changed unit to Byte in case of zero size drives.(DCSG00233705 (Port Of Defect DCSG00072680))
-Non-interactive/silent installation does not have options to install LSA based on EVENT NOTIFICATION CHOCIES..(DCSG00233706 (Port Of Defect DCSG00078199))
-WG MR 7.14 PA1: LSA allows to select 512B drives as DHSP for 4K DG.(DCSG00233708 (Port Of Defect DCSG00078853))
-WG 7.14:During VD creation filtering 4k drives displays blank PD table when mixing is not allowed.(DCSG00233709 (Port Of Defect DCSG00078974))
-LSA Client: Behavior mode parameters is not shown.(DCSG00233710 (Port Of Defect DCSG00079966))
-VDs of different capacities(MB/GB) is not sorting properly..(DCSG00233711 (Port Of Defect DCSG00080102))
-Legacy: LSA WG: LSA is allowing to change the personality mode of the controller in Non-admin access..(DCSG00233712 (Port Of Defect DCSG00083219))
-Silent installation with default Web server port and default LSA port is failing..(DCSG00233713 (Port Of Defect DCSG00092962))
-WG 7.14 PA2:managed server icon for self server is shown "add" in manage server page if we add ubuntu/ any server to manage server list..(DCSG00233714 (Port Of Defect DCSG00112829))
-LSA WG : Uninstall instructions mentioned in LSA ESXi readme is wrong..(DCSG00233716 (Port Of Defect DCSG00126899))
-Manage server page throws error message "400:" for invalid credentials..(DCSG00233717 (Port Of Defect DCSG00136334)
-WG: LSA Does not have filter button in drives tab for IT controller Controller console page.(DCSG00233718 (Port Of Defect DCSG00138885))
-Fixed: Spanned drive min vd check calculation error.(DCSG00233720 (Port Of Defect DCSG00138063))


007.013.014.000 - Moderate Impact
-------------------------------------
MR 7.13

Defects:
 -WG 7.13:Inconsistency in display of "Patrol Read" in the Properties page.(DCSG00071276)
 -Changing the ngroups list values.(DCSG00102619)
 -Shenandoah_MRSA : change personality option should not be enabled for both with linux and windows releases.(DCSG00072698)
 -Whitley ICX : LSA - Add physical drives option is not coming for user when trying to recon from R6 to R0.(DCSG00104470)
 -Fixed: Added disable nginx logging flags.(DCSG00065714)
 -Memory Leak issues in LSA Build.(DCSG00068484)
 -WG: Alignment issues in Remote discovery page, server summary page and Settings page.(DCSG00065480)
 -IT controller is not displayed int the view all controllers tab when it is in needs attention.(DCSG00061513)
 -Manual discovery page gets hung while adding the server to Auto discovery list..(DCSG00080451)
 -WG: Clicking on Manually added server in manage server page leads to blank page (calls fails with 502 error code).(DCSG00063209)
 -LSA: disableOffloadNum field should be match with latest schema.(DCSG00041224)
 -Channel controllers are discovered from MRSA Software.(DCSG00054278)
 -Fixed: user notification client list is not updated.(DCSG00053648)
 -WG 7.13: Hot spare Filter box alignment issue.(DCSG00067986)
 -LSA Common: LSA Crypto OEM specific changes.(DCSG00047290)
 -Windows installer (7.013.004.000) is unsigned.(DCSG00065620)
 -Cannot update CFF 440 FW with LSA.(DCSG00062602)
 -Firmware update page shows "None" for selected firmware.(DCSG00065566)
 -Orion MR PA10 - Foreign config is not showing properly in LSA when user pull/push the PD.(DCSG00053829)
 -due to unhanded battery removal event, battery health status was not reflecting as need attention.(DCSG00040271)
 -WG: Energy pack details does not load on clicking energy pack properties after clicking Refresh energy pack properties.(DCSG00058132)
 -MR7.13: Enhance debug Log level and entries in LSA Common code.(DCSG00041751)
 -Fixed:display of 2 enclose when only one is connected with multi path.(DCSG00069728)
 -LSA MR: Hand symbol is showing for all the fields in Server Profile and it is not clickable.(DCSG00062470)
 -WG: In presence of JBOD, after creating VD using all UG drives, the advanced configuration button gets disabled.(DCSG00065733)
 -update HBA 440-16i UEFI BSD failed via LSA.(DCSG00074275)
 -MRSA Firmware update page shows ,Selected Firmware Package version and it shows Firmware version.(DCSG00051098)
 -WG: Instance validation fails for Enclosure GET( MR 7.13, 7.013.004.000.(DCSG00066930)
 -MR-7.12: LSA VD creation failure message has spacing formatting issue..(DCSG00037910)
 -LSA Client : Non-VMware server is discovered with VMware check box enabled in Manual Discovery.(DCSG00051290)
 -Partial degraded VD icon is showing as optimal VD icon in LSA.(DCSG00054282)
 -WG: Duplicate entries of physical drive properties are displayed in case a property of physical drive is updated.(DCSG00069285)
 -WG 7.13: Patrol read option not seen for GHS in LSA.(DCSG00068977)
 -WG: Instance validation fails for Controllers GET (MR 7.13, 7.013.004.000), : Aero Controller.(DCSG00067932)
 -Remote discovery fails to load in RWC3 (7.013.009.000.(DCSG00083835)
 -Fixed: usage of wrong enum led to unknow characters in max lane width.(DCSG00049771)
 -WG: For the self server adding a read only user in manage-server page is logged in as a admin user.(DCSG00065605)
 -AMD 2P - LSA is not showing proper information when user trying to do RLM with same RAID level.(DCSG00040578)
 -MR 7.13 DBU: Flashing BIOS package failure with Completed status on Aero Controller when selected EFI-BSD.(DCSG00055757)
 -Windows Un-installer is not removing the SL Debug logs.(DCSG00054660)
 -WG MR7.13: LSA read me file needs to be updated with New OS matrix and inclusion of Aero cards.(DCSG00055714)
 -WG: Refresh energy pack properties displays error notification with status code : 1 on Vmware login.(DCSG00058321)
 -Notification for Enable /Disable security box is not pointing to Enable/Disable security option..(DCSG00067992)
 -LSA Server: LSA Crypto OEM specific changes.(DCSG00047618)
 -Handling Manual Discovery ADD case.(DCSG00077625)
 -LSA is not allowing user to change max number of PDs allowed under Set Patrol Read properties.(DCSG00068620)
 -Negotiated width and Max lane width property parameters for Nvme drives is shown as "Max user count reached" in LSA.(DCSG00046456)
 -Unmap property not update in VD/PD on enabling/disabling unmap at controller level.(DCSG00040172)
 -Server Profile _Linux: enclosure/Backplane information is blank / ServerIP is private in Linux OS.(DCSG00072694)
 -key board short cut does not work after using the print button during the installation.(DCSG00064684)
 -MR-7.13: LSA event ID 614 shown as Blank..(DCSG00037968)
 -WG: Changes required in naming convention of LSA to RWC3 in linux installation, RWC3 end user text has junk unicode characters in place of quotes and typo's.(DCSG00058406)
 -LSA_ 32 bit installer fails to launch in RHEL 8.1.(DCSG00087274)
 -Shenandoah:MRSA- Online Help gives 404 Not Found.(DCSG00051063)
 -Manage SAS Storage Link Speed/Premium feature/Manage Pcie Storage Interface operations have missing table borders & issues pertaining to column separators of the table.(DCSG00068937)
 -LSA MR : Each box in the List view of server page shows handsymbol but it is not clickable.(DCSG00062228)
 -RWC3 Common: Updating x64 nginx file.(DCSG00068595)
 -WG: clickable Checkboxes and "Confirm" notification texts does not have clickable mouse hover hand icons.(DCSG00069230)
 -LSA Client : NVMe Drive property changes w.r.t schema v32.(DCSG00079364)
 -MRSA shows " 0 Needs attention " when controller health status is "Needs attention ".(DCSG00056573)
 -WG: No LSA support logs generated with 7.013.003.00 linux Gateway.(DCSG00059955)
 -Orion MR PA10 - Same RAID level migration throws an error in LSA if user adding and removing any drives.(DCSG00053821)
 -Enhance the message of locked foreign can not be imported to cover boot time password skip.(DCSG00071157)
 -LSA Client : disableOffloadNum field should be match with latest schema.(DCSG00053497)
 -LSA Server: Resolving merge issues.(DCSG00032674)
 -Fixed:handled discovering multiple controllers.(DCSG00024769)
 -AMD 2P Wave2: LSA- Not able to create RAID00 with more than 32 PDS.(DCSG00042409)
 -Lone LF in body of email message.(DCSG00078494)
 -LSA is getting timed out while creating R6-64 VDs using 32 PDs.(DCSG00049772)
 -AMD2P-Wave2- LSA: Same RAID level migration throws an error in LSA if user adding and removing any drives.(DCSG00068647)
 -Ventura MR FW: Push Pull of drives showing wrong Enclosure ID..(DCSG00060541)
 -WG: Few of the keyboard shortcut keys are not working in case of RWc3 installation.(DCSG00058142)
 -MR-7.13: LSA Foreign import button not grey out after import is clicked with 240 VDs..(DCSG00068136)
 -StorCLI and LSA are not in sync while displaying the NVMe drive model Number after inserting the drive back..(DCSG00054602)
 -WG: Instance validation fails for PHY's GET and phy/0 GET (MR 7.13, 7.013.004.000.(DCSG00066942)
 -Use NVRAM to save PTB information -- API changes.(DCSG00082981)
 -Issue found due to code merge during code delivery process.(DCSG00075210)
 -Fixed: updated build script to add dirty bit to modifiable files. configuration file for client wasnot set with modifiable bit (+T)..(DCSG00058424)
 -MRSA: Supported controller information in the Readme File needs to be updated.(DCSG00056669)
 -Enter Key issue in Manual Discovery page is searching the servers without entering the IP..(DCSG00071404)
 -WG: For the self server which will be added to managed server by default should not show verify button.(DCSG00068954)
 -ICX_Whitley_Orion: LSA- Link speed details are not showing properly for Tape drive in WebGUI.(DCSG00075777)
 -"delete config" command clears the config, when OS/FS in the drive without "force" option.(DCSG00077464)
 -RWC3 windows build (07.013.009.000)loads with http instead of https.(DCSG00083839)
 -LSA MR Ventura: Alarm info is showing wrong when controller info tab is expanded..(DCSG00062219)
 -LSA report Power supply status only after LSA service restart.(DCSG00086465)
 -WG: LSA install shield says ready to install "OpenSLP 3.0.0.0 Arm64" instead of "openSLP 2.0.0.0 x86".(DCSG00063219)
 -Channel controllers are discovered from MRSA Software.(DCSG00053971)
 -Fixed: updated max drives for configuration service API.(DCSG00045337)
 -WG: Issues pertaining to schedule consistency check.(DCSG00069219)
 -Fixed: used data drives instead of total drive whie calculating min vd size.(DCSG00033996)
 -Orion_LSA: Maddux_Chinook: Slot numbers shown as 255 after expander resets.(DCSG00045472)
 -Fixed: Added minimum log support for thin OS.(DCSG00058212)
 -Display of unmap property at VD level.(DCSG00037620)
 -After installation of HPE_Generic linux 64 bit RPM, LSA service is not getting started..(DCSG00056838)
 -WG: Typo's in Readme and LSA.conf.(DCSG00058412)
 -Typo's in LSA.conf.(DCSG00061049)
 -WG: Copyright info needs to be updated from 2019 to 2020.(DCSG00068495)
 -LSA Readme file has to be updated for Aero controller support and proper open SLP web link..(DCSG00054273)
 -Inconsistency in the Server profile Headline representation.(DCSG00068909)
 -WG: Manual discovery page allows the user to add already added manually added VMware server.(DCSG00059470)
 -LSA Server: RAID volume creation failing with strip size conversion.(DCSG00048632)
 -LSA Client : Slot numbers shown as 255 after expander resets.(DCSG00055108)
 -LSAServer: Labeling mismatch between Enclosure Index and Enclosure ID.(DCSG00008078 (Port Of Defect DCSG00025255))
 -Ubuntu Linux install issues.(DCSG00032286 (Port Of Defect DCSG00033488))
 -LSA does not display Virtual drive info for foreign configuration.(DCSG00035555 (Port Of Defect DCSG00071356))
 -Legacy WG: Verify Credentials of the manually discovered server in Manage server page does not check if server is down.(DCSG00080854 (Port Of Defect DCSG00112141)
 -Fixed:LSA increased memory consumption with each event.(DCSG00031835 (Port Of Defect DCSG00070333))
 -Fan, Temperature Sensor , Voltage Sensor property issues related to Atlas board.(DCSG00035711 (Port Of Defect DCSG00071360)
 -Credits page needs an update.(DCSG00232932 (Port Of Defect DCSG00235896))
 -LSA _MR :- Error/warning message not displayed when unsupported characters entered for changing drive rate settings.(DCSG00134600 (Port Of Defect DCSG00136282))
 -LSA Advanced Configuration does not work with controller is with RAID mode , Personality behavior=RAID-0.(DCSG00063716 (Port Of Defect DCSG00065590))
 -When create or delete VD in LSA, VD information didn't refresh under LSA web in VMWare 6.7.(DCSG00068509 (Port Of Defect DCSG00069274))
 -LSA getting hung while loading in windows 2019 OS on Stonyford server.(DCSG00058328 (Port Of Defect DCSG00058797)
 -Health status changes of the remote server does not get updated in the gateway remote discovery page.(DCSG00086628 (Port Of Defect DCSG00087296)
 -Fixed: updated build script to add dirty bit to modifiable files. configuration file for client wasnot set with modifiable bit (+T)..(DCSG00058424 (Port Of Defect DCSG00071283))
 -RWC3 Home Page Help Button Hyper Link is Broken.(DCSG00050748 (Port Of Defect DCSG00061255))
 -LSA Client : Handle Manual Discovery failure cases.(DCSG00098052 (Port Of Defect DCSG00098056)
 -Starting LSI Storage Authority is seen in failed state during LSA installation on Rhel 8.2.(DCSG00115253 (Port Of Defect DCSG00239461)
 -LSA read me: Update the read me with all the required OS list.(DCSG00222589 (Port Of Defect DCSG00239476))
 -When selected 6272 KB firmware for update failure seen with message as file is more than 16MB size.(DCSG00080838 (Port Of Defect DCSG00102801))
 -Fixed: updated build script to add dirty bit to modifiable files. configuration file for client wasnot set with modifiable bit (+T)..(DCSG00058424 (Port Of Defect DCSG00070664)
 -Manual Discovery failure shouldn't return HTTP status:200.(DCSG00098024 (Port Of Defect DCSG00098034)
 -MR controller with No Alram is not auto refreshing on changing the controller properties.(DCSG00124484 (Port Of Defect DCSG00124768))
 
 EnhancementRequests:
 -Support for the New Energy Pack states.(DCSG00042776)
 -Implement changes to secureSign signing tool and infrastructure to support mixed list of PublicKeys that are from SCGCQ and DCSG.(DCSG00105430)
 -API change to support ISE completion status.(DCSG00065881)
 -MR API: Change event class for SPDM events.(DCSG00134416)
 -API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI STAT.(DCSG00222915)
 -LSA Standalone - port enhanced authentication/authorization to Linux.(DCSG00025327)
 -DCSG00234646
 -HPE Shenandoah: Type 2 Back plane Support.(DCSG00054712)
 -Linux: Installer script improvement.(DCSG00130050)
 -Remove Span setting for RAID 1 & 10.(DCSG00039596)
 -Preboot Trace Buffer [PTB] for Ventura/Aero - MR API.(DCSG00060713)
 -MR API: NVME Drive Init Error Report and Repair for Aero/Ventura.(DCSG00071534)
 -Implement support for Cross certificate and command - Windows signing using CNG Provider with HSM Protected Key.(DCSG00030211)
 -Allows cleaner exit with flushing of logs.(DCSG00039065)
 -DCSG00129388
 -DCSG00067060
 -Define MR_SAS_PHY_CONNECTION.currentSpeed when no devices are connected.(DCSG00071066)
 -Enhance debug Log level and entries in LSA Server code.(DCSG00038025)
 -Signing Linux executables via GPG method in HSM.(DCSG00077215)
 -Implemented: Logs levels appropriated.(DCSG00038028)
 -MR7.13: Enhance debug Log level and entries in LSA Server code.(DCSG00038019)
 -Request to change all BBU messages to CacheVault or Energy PAck as appropriate, since no longer supporting BBUs on latest Ventura products.(DCSG00031355)
 -Implemented secureSignCNG.exe CLI signing tool for Windows Signing..(DCSG00023491)
 -Blocking Management and display of the profile and Personality in MRSA as user can not change profile or personality from MRSA.(DCSG00041350)
 -SSD Wear Gauage.(DCSG00042810)
 -MR API changes - Support new DCMD for Platform Security SPDM.(DCSG00068355)
 -Include new field cannotSetMode in MR_AUTO_CFG_PARAMETER structure..(DCSG00072780)
 -Update RAID Web Console 3 solution to remove or re-direct Feedback.(DCSG00026525)
 -Ensure that the SSD cache policy is changeable and the status information is correct.(DCSG00214163)
 -Port secureSignBin.exe for MARGAY signing to GCP server environment.(DCSG00040377)
 -MR7.13: Enhance debug Log level and entries in LSA Server code.(DCSG00038027)
 -Request to change all BBU messages to CacheVault or Energy PAck as appropriate, since no longer supporting BBUs on latest Ventura products.(DCSG00031716)
 -API changes to expose MR_AUTO_CFG_PARAMETER for NONE mode.(DCSG00151058)
 -MR7.13: Enhance Server report log collection.(DCSG00039063)
 -HPE Shenandoah: Type 2 Back plane Support MRSA Client.(DCSG00054716)
 -Add new security events.(DCSG00167313)
 -Upgrade Install shield 2019.(DCSG00039535)
 -Support for the New Energy Pack states.(DCSG00042778)
 -LDET - Qx-2020 - RRB149 - Add immediate-binding flag to gcc-compiled deliverables.(DCSG00025854)
 -MR API: update field in event structure..(DCSG00093331)
 -Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API.(DCSG00226286)
 -MR7.13 - LSA Client: Update Snapdump save count field in show snapdump command.(DCSG00039516)
 -Updated secureSign.exe CLI tool and server-side controller scripts to use GCP server resources.(DCSG00003371)
 -SMART Polling Improvement- API Changes.(DCSG00214352)
 -LSA Server: RRB141 - Ensure that the SSD cache policy is changeable and the status information is correct.(DCSG00171246)
 -FW SAS MEGA API:Change MR_EVT_CTRL_FLASH_DISALLOWED_SB_KEY_CHANGE_PENDING event from Info to Warning.(DCSG00086780)
 -New MFI Stat for the updated recon behavior.(DCSG00229416)
 -MR API changes - Support new Provisional bit in CTRL INFO and new MFI status for Platform Security SPDM.(DCSG00106380)
 -Add support for signing MegaRAID Legacy BIOS CU Images (CTLR) images.(DCSG00143847)
 -MR7.13 - LSA Server: Update Snapdump save count field in show snapdump command.(DCSG00039505)
 -MR7 API: Add package incompatibility reporting.(DCSG00231443)
 -Aero multi-party signing partial signing of images.(DCSG00048670)
 -DCSG00025854 (Port Of EnhancementRequest DCSG00039673)
 -Multi path Enhancement in the server.(DCSG00071167 (Port Of EnhancementRequest DCSG00075640)
 -Linux LSA HSM based signing support.(DCSG00038899 (Port Of EnhancementRequest DCSG00042392))
 -Ensure that the SSD cache policy is changeable and the status information is correct.(DCSG00214163 (Port Of EnhancementRequest DCSG00240010))
 -LSA credits page update with latest open source components.(DCSG00074643 (Port Of EnhancementRequest DCSG00074715)
 -Windows LSA HSM based signing support.(DCSG00038808 (Port Of EnhancementRequest DCSG00042391)
 

NOTE TO SERVICE - Reference RETAIN #N/A
007.012.015.000  - Moderate Impact
-------------------------------------

Defects Fixed (100)
 -Fixed:LSA increased memory consumption with each event(DCSG00031835)
 -Scheduler Panel not aligned to center if Operations are performed on 32 VDs.(DCSG00016270)
 -Enable SSD guard fails with the error code : 3: Description: The requested command has invalid arguments.(DCSG00008031)
 -WG: Readme changes as part of MR 7.12.(DCSG00031356)
 -fixed: allow Cachecade VD creation.(DCSG00022978)
 -Aero DBU alpha (LSA):LSA crashes when make jbod/UG performed on multiple drives with Schedular wrapper enabled.(DCSG00024414)
 -7.12_EXT New OS support Matrix.(7.12_EXT New OS support Matrix).(DCSG00011435)
 -WG: Filtering with VMware and searching for auto discovered windows/linux server in manual disc page results in both success and failure messages.(DCSG00010481) 
 -fixed: nginx logs consuming large space on disk.(DCSG00032280)
 -WG:alignment issue in notifications.(DCSG00007250)
 -LSAServer: Labeling mismatch between Enclosure Index and Enclosure ID.(DCSG00008078)
 -Hide the Energy pack information when it is not present.(DCSG00031701)
 -Uninstall successful message not seen with RHEL OS & install exists with unary operator message if user provides input other than Y/N.(DCSG00012335)
 -SLES 15 Linux: Installer messages while creating symbolic link.(DCSG00023294)
 -LSAServer: Cleanup unused variables from LSA Crypto algorithm.(LSAServer: Cleanup unused variables from LSA Crypto algorithm)
 -Fan, Temperature Sensor , Voltage Sensor property issues related to Atlas board..(DCSG00035711)
 -"Your connection is not private" text overlap seen at manage server page.(DCSG00017191)
 -StoreLib API: Update SL_GET_ENCL_LIST with cmdParam_1b[0] for extended/legacy enclosure structures.(DCSG00053982)
 -WG: Aero DBU PA6(LSA): Performing VD operations does not update/clear the element count.(DCSG00012010)
 -Fixed: changed packaging script appropriatley.(DCSG00011424)
 -LSA Cache update for PD insert for it ctrls.(DCSG00020315)
 -Login Button gets disabled when user name is filled and Authentication Fails.(DCSG00014659)
 -LSA install exits if the user clicks enter key on any point during installation.(DCSG00026178)
 -MR 7.12: LSA Client- Coverity Defect Fixes.(DCSG00028104)
 -Modify the Alert setting put request to send only delivery mechanism when Email is not modified.(DCSG00007449)
 -MR-7.12: FW EPD bit is enabled in RAID personality Mode..(DCSG00036066)
 -WG: Remote discovery page does not load with RWC3 gateway installation: MR 7.12.(DCSG00057422)
 -Fixed: library to communicate with vmware server for arm.(DCSG00010202)
 -LSAClient: Labeling mismatch between Enclosure Index and Enclosure ID.(DCSG00012720)
 -SLES 15 Linux: Un-Installation is not removing the complete folder structure.(DCSG00023296)
 -fixed: show only eleigible Raid level for migration.(DCSG00025527)
 -WG_7.12: On SLES 15 OS, After login, on doing some basic operations LSA, it redirects to 50x.html.(DCSG00022866)
 -Refresh the Client page on Enclose link Restore and link lost.(DCSG00014979)
 -Resolved built time dependency.(DCSG00008091)
 -LSA Common:Enhance user notification about the unsecured connection.(DCSG00008073)
 -WG 7.12 Alpha:Jbod conversion is not happening with OS drive.(DCSG00031718)
 -WG: no notification regarding "EMAIL/SMTP server related setting get modified" when user hovers between mail server and Email tab while adding email.(DCSG00020145)
 -LSA - AMD 2P Wave 1 - LSA is getting crashed while upgrading from 007.012.004.000 to 007.012.005.000 version.(DCSG00022361)
 -WG:7.12 Alpha : Enable/disable Scsi Unmap option not shown for the VD created using unmap capable drive..(DCSG00026497)
 -LSA Linux: Maintain the resource files across the build upgrade.(DCSG00007897)
 -LSA Server : JBOD removal/insert events in LSA are not compliance with FW Events..(DCSG00032366)
 -(LSA):Facing " ./LSA: ./libssl.so.1.0.0: no version information available" error while LSA installation.(DCSG00022170)
 -Fixed: Simple configuration feature is disabled if unconfigured drives are not available.(DCSG00025334)
 -LSA Common: Update the script files specific to LSA Crypto.(DCSG00031407)
 -IR Client Refresh: On Start/Stop CC.(DCSG00017218)
 -Libutils and Libutils2 scripts changes.(DCSG00012770)
 -LSA does not display Virtual drive info for foreign configuration.(DCSG00035555)
 -WG: Windows Direct agent not getting discovered in remote discovery page as well as manual discovery page.(DCSG00009390)
 -LSA AMD2P Wave 1: User is getting wrong info about max number of PD support for R1/R5 while doing RLM.(LSA AMD2P Wave 1: User is getting wrong info about max number of PD support for R1/R5 while doing RLM)
 -Ubuntu Linux install issues.(DCSG00032286)
 -Fixed: Slpd supported for rhel/sles/ubuntu is packaged.(Fixed: Slpd supported for rhel/sles/ubuntu is packaged)
 -StoreLib header: Update comments in Topology structures for attached devices to Atlas.(DCSG00061230)
 -WG 7.12 Alpha: LSA continues to be in debug mode when "./LSA -" executed for configuring LWM alert settings.(DCSG00028583)
 -When create or delete VD in LSA, VD information didn't refresh under LSA web in VMWare 6.7.(DCSG00068509)
 -WG: non Generic Icon shown for IT in CC page, typo in batch failure notification, no notification for premium feature key above 40 character.(DCSG00027350)
 -WG: LSA -console enters an infinite loop on entering a character/string as input.(DCSG00008008)
 -LSA upgrade fails from 7.10 patch RO to 7.12 RO with ./deleteOldVersion.sh: line 79: ((: 009: value too great for base (error token is "009") in SLES 12 SP4.(DCSG00014016)
 -Client: Schema changes for lanes.(DCSG00010703)
 -LSA does not allow the user to configure alert settings.(DCSG00031332)
 -WG: MR 7.12 : Arm SLIR3 version is shown empty in view server profile.(DCSG00008006)
 -LSA - AMD 2P Wave1 - Same RAID level migration throws an error in LSA if user is not adding/removing any drives.(DCSG00028267)
 -LSA GUI display empty page when launching the app.(DCSG00014599)
 -LSA Server: Handle new MFI status in LSA.(DCSG00031865)
 -fixed: updated LSA version.(DCSG00008023)
 -LSA Server: Add MRMonMsg project to the LSA solution.(DCSG00007928)
 -Fixed: lane width is displayed as unknown.(DCSG00035811)
 -Schema changes for lanes.(DCSG00010702)
 -On ARM server during LSA upgrade, ./deleteOldVersion.sh: line 53: LSIStorageAuthority: command not found error is observed.(DCSG00025403)
 -WG: lsa.exe -console fails to execute with LWM installed on windows machine.(DCSG00007461)
 -ARM Ubuntu: Linux Uninstallation leaving slpd process alive.(ARM Ubuntu: Linux Uninstallation leaving slpd process alive)
 -WG: Manual discovery of the ubantu server from windows gateway lists it as VMware server, issue related to search and adding already discovered server.(DCSG00010474)
 -Fixed: Added aarch64 detection code for linux.(DCSG00008022)
 -LSA Advanced Configuration does not work with controller is with RAID mode , Personality behavior=RAID-0.(DCSG00063716)
 -Even after LSA is uninstalled the LSA and Nginx port numbers are still busy, reinstallation requires using alternate free ports: Ubuntu.(DCSG00011517)
 -Address property Display mismatch for PD and Enclosure properties for MR and IT.(DCSG00017217)
 -LSA Server: External defect review:id=45919.(DCSG00007404)
 -For unconfigured bad drives, typo in Negotiated link speed & Drive speed in physical Drive properties page.(DCSG00007251)
 -Fixed: Resolved primary nic interface data population.(DCSG00010261)
 -LSA under Drives for IT controllers is showing selected elements 0 always.(DCSG00015834)
 -WG_7.12_LSA: Invalid VD size range notification is shown on entering VD capacity out of range.(DCSG00007446)
 -WG: Aero DBU Alpha(LSA): Select all snapdump --> deselect one of snapdump and then click on headline deselects all selected snapdumps.(DCSG00027305)
 -Fixed: missing span was not handled appropriately in DG health.(DCSG00027676)
 -WG: Mutliselect PD notification for IT controllers notifies user to select multiple Virtual Drive rows, clicking on FW version does not lead to FW update page.(DCSG00027320)
 -LSA crashes when clear drive operation performed.(DCSG00022528)
 -WG: during uninstallation of LSA from the control panel the publisher information is not shown in windows.(DCSG00042280)
 -Fixed: slpd didnt start durint startup.(DCSG00011426)
 -LSA Common: Handle events 610-613.(DCSG00008066)
 -Fixed: updated openssl library.(DCSG00010277)
 -WG:7.12:abort core dump seen for rekey operation on LSA..(DCSG00009381)
 -RWC3 Home Page Help Button Hyper Link is Broken.(DCSG00050748 Port Of Defect DCSG00057415)
 -WG: Copyright info needs to be updated from 2019 to 2020.(DCSG00068495 (Port Of Defect DCSG00068560))
 -DCSG00037620 (Port Of Defect DCSG00037685)
 -LSA Server: Resolving merge issues.(DCSG00032674 (Port Of Defect DCSG00032824))
 -LSA Readme file has to be updated for Aero controller support and proper open SLP web link..(DCSG00054273 (Port Of Defect DCSG00062969))
 -Add the language support matrix in to LSA readme.(DCSG00024412 (Port Of Defect DCSG00024705))
 -LSA IT : Not able to sort the drives based on drive "Model"..(DCSG00032171 (Port Of Defect DCSG00048474))
 -LSA getting hung while loading in windows 2019 OS on Stonyford server.(DCSG00058328 (Port Of Defect DCSG00058796))
 -LSA MR: VD(Raid5) status is showing as degraded, instead of offline..(DCSG00032167 (Port Of Defect DCSG00032180))
 -LSA show incorrect physical drive information, when drive push pull operation performed..(DCSG00026587 (Port Of Defect DCSG00026634))
 
 EnhancementRequests:
 -LSA Server:Add security-related compiling flags to LSA 3rd Party Components.(DCSG00010237)
 -Ubuntu support for RWC3.(DCSG00016264)
 -Enhance user notification about the unsecure connection.(DCSG00008000)
 -Linux LSA HSM based signing support.(DCSG00038899)
 -LSA Windows: Maintain the resource files across the build upgrade.(DCSG00021254)
 -Windows LSA HSM based signing support.(DCSG00038808)
 -API change to support 1. OEM specific UBM Back planes, and 2. Smart Battery state.(DCSG00040165)
 -Update MR API mr_drv.h to modify field for RTTRace_header.(DCSG00042985)
 -LSA Common:Add security-related compiling flags to LSA 3rd Party Components.(DCSG00010240)
 -API change OOB Self Diagnostics Design Improvements.(DCSG00054194)
 -LSA to handle the new error code populated by the SL IT.(DCSG00024064 (Port Of EnhancementRequest DCSG00024476))
 -DCSG00019108 (Port Of EnhancementRequest DCSG00019110).
 -DCSG00019108 (Port Of EnhancementRequest DCSG00019288).
 

007.010.016.000  - Moderate Impact
---------------
Defect:
 LSA MR: VD(Raid5) status is showing as degraded, instead of offline.(DCSG00032167)
 LSA IT : Not able to sort the drives based on drive "Model".(DCSG00032171)
 LSA does not display Virtual drive info for foreign configuration.(DCSG00035734 port of DCSG00035555)
 WG_7.12: On SLES 15 OS, After login, on doing some basic operations LSA, it redirects to 50x.html.(DCSG00026970 port of DCSG00022866)
 LSA 7.10 + Ubuntu Linux install issues.(DCSG00032287 port of DCSG00032286)
 Aero DBU alpha (LSA):LSA crashes when make jbod/UG performed on multiple drives with Schedular wrapper enabled.(DCSG00026968 port of DCSG00024414)
 nginx logs result in large disk space consumption.(DCSG00032285 port of DCSG00032280)
 SLES 15 Linux: Un-Installation is not removing the complete folder structure.(DCSG00027735 port of DCSG00023296)
 
EnhancementRequest Records Linked (4):
 New Event for firmware DMD handling
 StoreLib.h: Enhanced debug logging mechanism
 Storelib.h: Add new SL API SL_OOB_SET_TRANSPORT_TYPE to dynamically load SL in any oob mode
 API changes for Request to change all BBU messages to CacheVault.
 API changes needed for DPMstat support in MegaRAID SAS 3.5 controllers
 LSA 3rdParty :Add security-related compiling flags to LSA 3rd Party Components
 Automating Arm Builds


007.010.014.000 - Moderate Impact
---------------

Defects (277)
 - WG: Enclosure:Slot number is not displaying in Ascending or Descending order, if other columns are clicked first.(SCGCQ01874775)
 - Issues wrt the linux installer script(SCGCQ01879303)
 - WG: installing LSA on linux 64 bit machine throws an error " ‘/root/Desktop/LaunchLSA.desktop’: No such file or directory"(SCGCQ01897393)
 - IR3: Drive count is 0 and no PDs were listed in Controller console Page--> Drives Tab(SCGCQ01898255)
 - LSA Event ID 519 shows blank.(SCGCQ01901169)
 - Incorrect icon displayed along with "settings saved" message.(SCGCQ01905838)
 - LSA:Loading More data initially in BGOPS Progress bar in LSA and later Device ID disappears(SCGCQ01937373)
 - PH10 PA LSA is not launching after a upgrade from v007.009.002.000 to 007.009.003.000(SCGCQ01940193)
 - WG: No Action Successful notification shown on Drive erase(single Drive)(SCGCQ01941129)
 - LSA 7.9: Mismatch of sector size string between PD table and Group name(SCGCQ01942630)
 - LSA Server: LSA needs to Handle when controller is in safe Mode(SCGCQ01949074)
 - LSA is not launching after a upgrade from v007.009.002.000 to 007.009.003.000(SCGCQ01949090)
 - Linux binary not working.(SCGCQ01949665)
 - WG: String Changes related to VD operations, Filter blank box turn blue, expand backplane icon can be removed when drives=0(SCGCQ01960486)
 - Fixed: WG: LSA manage link speed pane does not provide any info to user on which port is connected/disconnected(SCGCQ01963966)
 - SmartCarrier Enclosure type shown as "vSES" in LSA(SCGCQ01965395)
 - : MRSA shows Bay Count as 255 under Enclosure / Backplane properties(SCGCQ01965427)
 - LSA:Add Logical drive Page give option to select"Cached IO" for an LD and Error message not Branding compliant(SCGCQ01965445)
 - LSA 7.9 alpha:issues pertaining to migration from degraded Unmpa R5 to R0(SCGCQ01966275)
 - LSA 7.9 Foreign config Import doesnt work correctly with Raid 1 VD(SCGCQ01966687)
 - WG:GUI issues:50x Html file,View server profile with no enclosure,View More of System messages, Restore Settings notification(SCGCQ01968404)
 - WG: GUI issues Pertaining to alignment of notification on scroll of LSA page	(SCGCQ01968457)
 - WG: LSA fails with the empty status description on trying to change the personality in presence of snapdump(SCGCQ01969570)
 - Fixed: Can't Create 5 VDs R6 using 4 pds with AWB,ARA policy with different strip size(SCGCQ01970007)
 - WG: no success or failure message is shown on updating the drive secuirty key(SCGCQ01970452)
 - Port information missing under Enclosures List.(SCGCQ01972260)
 - LSA Server: Returning wrong status code as return value - Status Code and Description implementation(SCGCQ01972673)
 - Reference to BBU in Server profile page(SCGCQ01976904)
 - Shenandoah_MRSA: Listing SAS SSD drive while trying to migrate an array configured with HDD's.(SCGCQ01976926)
 - Logical drives are listed in the GUI when all the drives are pulled out	(SCGCQ01976929)
 - LSA Server: Returning wrong status code as return value - Status Code and Description implementation(SCGCQ01977769)
 - Fixed: Added check for missing drive case(SCGCQ01978914)
 - Fixed: LSA stops responding after creating Vd with 4k Drives(SCGCQ01978965)
 - VD/HotSpare reference in Clear Configuration Confirmation popup-Regression(SCGCQ01979076)
 - Summary: Gateway LSA is not responding in SLES 12 64bit(SCGCQ01979137)
 - Error code is not displayed for DG add VD operation failure(SCGCQ01988209)
 - Modify array option available for Degraded R5 , Blank screen followed "0 drives" on removing drives(SCGCQ01988400)
 - Fixed: update Validation Check codes for the image file(SCGCQ01989969)
 - Aero A0: RWC3 does not show version of Selected Firmware Version for updating(SCGCQ01989970)
 - LSA 7.9:Secure using FDE option is not shown for VD(using OPAL(SCGCQ01993099)
 - Fixed: OS name for localhost is inconsistent with the Osname populated when discovered via slp(SCGCQ01994459)
 - LSA 7.9:Send Email functionality of LSA is not working.(SCGCQ01998245)
 - Fix: WG: Intance validation for Controller Get fails : MR Ventura(SCGCQ01998299)
 - WG: Instance validation for PD and Configuration service GET fails with " isSupportedByFW' & 'securityType' was unexpected(SCGCQ01998305)
 - Memory Leak issues LSA Build (7.009.007.00(SCGCQ02006229)
 - WG: Switching between view server profile and settings page would not load the view server profile(SCGCQ02007150)
 - WG: Enabling or disabling SSD guard fails with error code "1", Description: "SSD Guard Disable Failure (SCGCQ02009718)
 - LSA 7.9: Action successful notification is not seen for encrypting the DG(SCGCQ02010670)
 - LSA: Mismatch in Unconfigured Good string(SCGCQ02016646)
 - LSA: Patrol Read string display issue(SCGCQ02016879)
 - WG : LSA 7.9 Status code for Drive security disable message is showing same for StatusLevel 0 and 1(SCGCQ02018083)
 - Difference in naming of Array during Array creation(SCGCQ02019200)
 - WG: GUI issues pertaining to star/stop patrol read & remote discovery page(SCGCQ02019555)
 - Back-plane information showing as blank in server profile page.(SCGCQ02019592)
 - LSA 7.9:Clear config is successful when OS Pd and other PDs are in jbod state(SCGCQ02021372)
 - LSA : Updating FW pkg version is not shown during FW upgrade/downgrade.(SCGCQ02023284)
 - PH11 PA LSA - Attached Drive info not displayed under controller page(SCGCQ02023407)
 - LSA 7.10:Unsupported drives are displayed as UG under server profile page.(SCGCQ02030950)
 - LSA: LSA Crashes on updating firmware and doing OCR, not able to recover further	(SCGCQ02032031)
 - WG: LSA manage link speed pane does not provide any info to user on which port is connected/disconnected(SCGCQ02032824)
 - Error message displayed for entering wrong password to unlock foreign VD/PD should be updated.(SCGCQ02034263)
 - PH11 PA - LSA IT - Copyright info needs to be updated(SCGCQ02034466)
 - Fixed: WG: Instance validation for Controller Get fails(SCGCQ02035158)
 - WG: mouse hover icon missing for the connected device property column in manage link speed pane(SCGCQ02035223)
 - WG:Unable to perform Enable SCSI Unmap operation when DHSP is removed from the VD.(SCGCQ02035226)
 - Shenandoah_Aero: LSA crash observed while trying to create more than maximum LD allowed(SCGCQ02035317)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02035322)
 - WG: Selected element count does not get updated after auto page refresh when VD expand operation is performed(SCGCQ02036089)
 -(SCGCQ02036091)
 - WG: wrong notification shown on trying to unlock a foreign FDE drive with wrong passphrase and then with correct passphrase(SCGCQ02036701)
 - Aero DBU PA1:LSA-Issue pertaining to add hotspare while creating Vd(SCGCQ02038235)
 - Cacheinit should not issue READ_AFTER_IMPORT dcmd id no foreign pd present.(SCGCQ02038386)
 - LSA - Patrol Read maxconcurrentpd count in LSA should be inline with FW(SCGCQ02040516)
 - MRSA: Crash when tried to flash corrupt firmware(SCGCQ02040739)
 - Shenandoah_MRSA: Warning message improvement when tried to delete LD formatted with File System(SCGCQ02042555)
 - LSA Client: MRSA: Crash when tried to flash corrupt firmware	(SCGCQ02043781)
 - WG : LSA 7.10 Keyboard short cut keys are NOT there for Different pages of LSA Installation pages(SCGCQ02045646)
 - Fixed: OCR should trigger update of dual image components(SCGCQ02048856)
 - WG: Issues pertianing to set snapdump properties page--> enable disable snapdump and changing cache offload limit.(SCGCQ02048906)
 - WG: Incomplete foreign VD is seen when Clear foreign config is performed, incorrect status code on rescan after clear foreign(SCGCQ02049476)
 - WG:Securing JBOD option gets disabled if from list of JBODs selected even if one is unselected(SCGCQ02049479)
 - LSA displays one of the PD's is missing as part of foreign config even if all the PDs are connected(SCGCQ02049511)
 - WG: Few of VD and PD operations will not be usable in LSA without zooming out ((SCGCQ02049819(SCGCQ02049819)
 - WG: in presence of missing drive the select all and element count does not work properly in span drive tab(SCGCQ02050441)
 - WG 7.10:Advance controller info does not show whether energy pack is connected or not(SCGCQ02050502)
 - WG 7.10:Number of foreign config count is not updated if clear drive operation performed on a foreign pd.(SCGCQ02050579)
 - WG 7.10:Migration from r0 (31 pds(SCGCQ02050857)
 - Error and Warnings thrown while install/upgrade MRSA on SLES15(SCGCQ02053038)
 - WG: LSA notifications GUI issues & Other Hardware user info on expanding enclosure info, LSA conf file, Message_en file(SCGCQ02053156)
 - WG: UI Elements alignment for DG actions and Fixed action menu with lower resolution(SCGCQ02053167)
 - LSA Firmware package version shown as version in controller action page.(SCGCQ02053748)
 - LSA Simple configuration from main page shows blank when JBOD are present.(SCGCQ02053891)
 - Fixed: Last Vd size was not being checked for alignment(SCGCQ02058284)
 - Fixed: timestamp inside compressed file is not appropriate(SCGCQ02058485)
 - LSA capacity column sort not working in other Hardware Tab.(SCGCQ02058597)
 - Default Logical Drive name is showing as "VDName**" , while creating Logical drive through Simple Configuration(SCGCQ02062623)
 - WG: Element count not updated on selecting foreign drives and sorting Foreign drive list, it continues to show PD operations(SCGCQ02063630)
 - MRSA: LD Name discrepancy for 1 LD and 2 LDs without LD_Name during Array creation(SCGCQ02067043)
 - In presence of NVME drives, applying and Clearing filter and then sorting the drives results in incorrect PD list(SCGCQ02069473)
 -(SCGCQ02069524)
 -(SCGCQ02074686)
 - WG_7.10: Spacing alignments to be done in the VD setting page during the VD creation	(SCGCQ02076790)
 - WG_7.10: While consistency check is in progress on VD, if we click pause progress bar is misaligned(SCGCQ02076792)
 - Fixed: check in place to create nvmeOnly disk group during migration	(SCGCQ02076800)
 - WG: FDE foreign config after performing instant secure erase on one of the drive shows incomplete in LSA(SCGCQ02080536)
 - WG_7.10: Spell check and spacing issues in Latest LSA (007.010.003.000)(SCGCQ02081258)
 - "Drive Group list is empty" error message seen when multiple drives are assigned as DHSP to a VD, issue per(SCGCQ02081264)
 - Silent installation is NOT working on Ubuntu 16.04(SCGCQ02082129)
 - Download support Log not working.(SCGCQ02082514)
 - Aero (DBU PA3(SCGCQ02082524)
 - DG number displayed outside the box(SCGCQ02089434)
 - Aero DBU PA2(LSA	(SCGCQ02091088)
 - WG: selected element count shown wrong on selecting PD list(including mising(SCGCQ02095469)
 - Fixed: missing pd info was leading to population of wrong candidate pds(SCGCQ02095494)
 - WG: LSA Lists drives of a type even if less for a raid level creation if user selects raid level from compare select(SCGCQ02096215)
 - Fixed: Changed build files to build client for ESXi(SCGCQ02096396)
 - WG: LSA snapdump files generated are only of 32 kb even if the actual snapdump file size is much higher than that(SCGCQ02100467)
 - WG: Filter options does not list NVMe drives in PD list of controller console page(SCGCQ02107270)
 - WG: extracting snapdump file using 7zip, user is notified regarding header error in etty file, spacingissue of text in OFU(SCGCQ02108538)
 - LSA - While doing RLM from R6 to R1, odd number of drives option is coming for R1(SCGCQ02108817)
 - Fix API changes done for NVMe readiness(SCGCQ02142981)
 - Add NVMe width comments to mr.h(SCGCQ02146846)
 - Fixed: changed the max drive value of R1 for cachecade drives(SCGCQ02169419)
 - LSA - AWB option is coming for CC VD with Rambler card while creating CC VD(SCGCQ02169687)
 - LSA Cache update for PD insert for it ctrls(SCGCQ02191080)
 - WG: LSA does not display the correct VD creation time in VD get URI response(SCGCQ01889478)
 - MRSA : NO option to go forward while configuring the VD`s if all drives are in JBOD.(SCGCQ01902964)
 - LSA 7.9: Display error for "OS name" when expand/minimize is performed.(SCGCQ01904365)
 - Fixed: Configuration service changed to accomadate allomixinSSD bit(SCGCQ01925161)
 -(SCGCQ01927978)
 - LSA 7.9:Changing server parameter in Configfile.json file to 2 , scheduler does not kick inn and LSA crashes(SCGCQ01930410)
 - LSA 7.9 PA:failure messange with description success on enabling/disabling scsi unmap feature.(SCGCQ01936667)
 - WG: After adding an VMware server manually to remote discovery page, the " GO to manage server page is not clickable"(SCGCQ01940852)
 - RWC3 Linux License Agreement and Desktop Shortcut Is for LSI instead of RWC3 (Windows RWC3 is okay(SCGCQ01942985)
 - Fixed: Foreign drives are not considered as configured & which leads to a mismatch in JBODconversion count during VD creation(SCGCQ01943388)
 - LSA Client: GWT Popup panels are morphing the GWT fixed panels(SCGCQ01943617)
 - LSA 7.9: Mismatch in "Unconfigured drives and replace drive" count.(SCGCQ01944392)
 - WG: VD creation page does not show VD count and capacity of VD that can be created using unmap drive(SCGCQ01952143)
 - LSA 7.9:Unable to start instanst secure erase operation on multiple Pds when scheduler is on.(SCGCQ01955160)
 - WG: Issues pertaining to Settings page(SCGCQ01956683)
 - WG: After creating VD from server summary page opens empty JBOD conversion page, issue pertaining sector size in filter(SCGCQ01957078)
 - LSA 7.9 alpha:Disable data protection option is seen for non-secured & secured VD in presence of locked foreign PD(SCGCQ01960300)
 - LSA 7.9 alpha:Incomplete foreign found after unlocking the Locked foreign config during the Reconstruction.(SCGCQ01962216)
 - LSA 7.9 alpha :The error code 69636 is seen without view more option when pause on CC operation is performed twice(SCGCQ01971576)
 - WG:LSA displays the snapdump count in hex value, GUI issues in snapdump pane(SCGCQ01973964)
 - MRSA event for Drive erase abort is coming blank in "View Event log" for event ID 421(SCGCQ01976894)
 - LSA 7.9:when multiple Vds are added on the existing DG, there is inconsistency in the Vd name(SCGCQ01978171)
 - Fixed: "All the listed drives cannot be mixed" displayed while creation of R0 with "select all" option.(SCGCQ01979083)
 - fixed: LSA doesnt consider Copyback state while counting configured pds.(SCGCQ01979598)
 - LSA : Port details are missing in drive removal/insert events.(SCGCQ01979793)
 - Fixed: missing Event description for new events was pausing LSA(SCGCQ01980570)
 - LSA 7.9:LSA Gray page is seen when multiple VDs of multiple DGs are deleted.(SCGCQ01983080)
 - MRSA : Copyback progress details is not proper in BGI progress tab.(SCGCQ01996577)
 - (SCGCQ02003711: Add default HTTPS to RWC3(SCGCQ02003711)
 - WG: GUI issues : Drive Security text on Hover, system messages clickable text, bell button notification(SCGCQ02006538)
 - “404 Not Found” seen on upgrading Snap4 GA to OEM Builds and later removing and installing new build(SCGCQ02016688)
 - LSA 7.10:Covert button of the Jbod table is activated and flickers when more than eligible count pds are selected.(SCGCQ02024507)
 - WG: No VD or PD details shown for progress operation in VMware(SCGCQ02028695)
 - Shenandoah_Aero: LSA crash observed while trying to create more than maximum LD allowed(SCGCQ02031517)
 - WG : LSA Cache Offload Limit value change was not changing without manual refresh(SCGCQ02043843)
 - WG: LSA view event log list the Portmap as '0' instead of '08' for scsiType=0 (ie PDs)(SCGCQ02045715)
 - LSA: Authenticated User group is given Read only privileges after adding Authenticated Users to full_access_groups.(SCGCQ02045735)
 - WG: LSA does not show the details of the current profile when there is only one profile supported(SCGCQ02045758)
 - WG: System LSA monitor event logs has junk characters(SCGCQ02049034)
 - WG: Path information for PD reset event is empty in event logs (event id : 268(SCGCQ02049577)
 - LSA: Domain login for administrator fails with "Error code:49 Invalid credentials".(SCGCQ02049807)
 - WG 7.10:if VD count is above limit and VD capacity is changed, LSA allows user to create VD which fails(SCGCQ02050533)
 - LSA Simple Configuration for R6 fails with error.(SCGCQ02053837)
 - LSA service crashing in ubuntu(SCGCQ02061370)
 - Linux Build is always picking old library(SCGCQ02061380)
 - Aero DBU PA2(LSA	(SCGCQ02065672)
 - Incorrect number of slots is displayed for UBM U.2X2 Vses Backplane in LSA.(SCGCQ02069871)
 - Fixed: Calculation to get possible range for RLM	(SCGCQ02070841)
 - Aero DBU PA2(LSA	(SCGCQ02074776)
 - WG_7.10:In the Error code:118 description, Spacing alignments to be done.(SCGCQ02076794)
 - WG_7.10: SAS address is shown for PCIe (NVME	(SCGCQ02076924)
 - Wide port info is not displayed for physical drive under connector name for Backplane attached drives.(SCGCQ02076933)
 - LSA: VD actions performed using storcli not reflected under LSA's Virtual drive tab(SCGCQ02078435)
 - LSA: Read_only_access group users are given administrator privileges(SCGCQ02078614)
 - WG: User is notified to select the Drive group even if VD and PD tab of the DG is clicked(SCGCQ02080553)
 - RWC3 Windows Readme contains IR3 controllers under supported controllers list(SCGCQ02081038)
 - During LSA upgrade some of the old build files are not removed in Ubuntu	(SCGCQ02082116)
 - WG 7.10: wrong health status of a gateway server seen when discovered from same gateway server.(SCGCQ02084545)
 - WG:LSA Direct agent or LWM installation from main package creates desktop shorcut in linux(SCGCQ02084636)
 - WG 7.10:Scheduler wrapper does not kick in for enable security operation(SCGCQ02085660)
 - Fixed: FDE and Opal mixing shouldn't be allowed(SCGCQ02086784)
 - Migration from R1 Vd(4 drives)(SCGCQ02087362)
 - Element action pane border incomplete during single PD selection, user name/password blue box alignment(SCGCQ02091191)
 - Issue pertaining to failure notification(SCGCQ02095408)
 - Fixed: FW upgrade issues with Aero FW files(SCGCQ02097971)
 - Fixed: R00 max pd limit is changed to be aligned with fw requirement(SCGCQ02108807)
 - LSA wrongly treats "MaxAHCIDev" as "Max SATA supported drives" in profile info.(SCGCQ02119031)
 - Fixed: Cachecade VD creation diaglog doesnt populate Raid levels	(SCGCQ02142026)
 - "Remove drives" option should not come if user is doing RLM from R6 with 3 drives to R5(SCGCQ02184393)
 - WG: LSA manage link speed pane does not provide any info to user on which port is connected/disconnected(SCGCQ01512320)
 - LSA needs to Handle when controller is in safe Mode	(SCGCQ01838234)
 - MRSA : MRSA shows the logout option in drop down menu .(SCGCQ01902913)
 - LSA 7.9: Unable to enter password while adding mail server authentication.(SCGCQ01933819)
 - LSA 7.9 :Status error description for schedular operation is not mapped to the proper device ID.(SCGCQ01940978)
 - WG: NO PD info is shown for foreign configuration(SCGCQ01942159)
 - WG: Instance Secure Erase is not giving any action indication(SCGCQ01942452)
 - WG:Remove icon for manually added server not shown in manage server page, Signin should be disabled when login in progress(SCGCQ01960469)
 - Scheduler API call in not working in standalone mode of installation(SCGCQ01961390)
 - LSA 7.9 alpha: Error code 69642 is seen when disable/enable unmap operation is performed on Unmap VD.(SCGCQ01963097)
 - fixed: logout of indirect agent causing gateway session to expire(SCGCQ01969806)
 - WG: All the events to Vmware are coming as information(SCGCQ01973905)
 - LSA 7.9: Incorrect critical message displayed for Offline PD.(SCGCQ01979150)
 - Fixed: Updated curl library for Linux OS	(SCGCQ01979794)
 - LSA 7.9: Re-scan button is disabled after GHS import.(SCGCQ01982953)
 - LSA 7.9:FDE HDDs are assigned as DHSP for an encrypted OPAL VD(SCGCQ01982973)
 - Status reports as failed although firmware is updated successfully(SCGCQ01983031)
 - MR 7.9 PA: LSA Win: 7.9_PA-007.009.007.000 Fails to display JBOD, StorCLI works fine(SCGCQ01994803)
 - LSA does not show failure or success notification when clear configuration is performed.(SCGCQ01996512)
 - WG: Instance Validation failed for Event history GET	(SCGCQ01998296)
 - LSA - Selected firmware version displayed as blank during update firmware(SCGCQ02034485)
 - LSA: Administrators User group is given Read only privileges after adding Users to Administrators group.(SCGCQ02048915)
 -(SCGCQ02048923)
 - Client changes for review-30 schema compliance(SCGCQ02062850)
 - Aero DBU PA2(LSA	(SCGCQ02065575)
 - LSA Windows Readme: Update the LSA Windows Read me with the enhanced Silent installation instructions(SCGCQ02070840)
 - WG: snapdump downloaded after host triggered snapdump is not in zip file format(SCGCQ02084515)
 - WG 7.10: LSA crashes when generate snapdump or dowload snap dump operations are performed on direct agent(SCGCQ02094537)
 - GUI css issues with update firmware panel and snapdump actions(SCGCQ02094845)
 - Spacing issues seen while converting a drive from JBOD to UG	(SCGCQ02095422)
 - WG:Enclosure ID and Device ID display inconsistency in SS page and CC page, Configure options in SS page alignment issues(SCGCQ02095855)
 - LSA couldn't install successful in RHEL 8.0 without OpenSLP installed(SCGCQ02103116)
 - Capacity sorting is not working in presence of TB drive in the PD list of VD creation.(SCGCQ02107449)
 - Snap dump trigger time format ends with Z character.(SCGCQ02184362)
 - WG: with loop back SMTP Ip, only the test email is received to broadcom mail id, able to add duplicate email id to email tab(SCGCQ01880101)
 - Fixed: when SasSata-mixing-policy is set to false vd creation options are not getting populated(SCGCQ01880184)
 - WG 7.8: Dedicatedhotspare and Replace missing drive tables are combined in LSA(SCGCQ01888233)
 - LSA 7.8: Incorrect VD capacity size displayed during VD creation(SCGCQ01897176)
 - LSA 7.9: Mismatch in the alignment of server list.(SCGCQ01904368)
 - Update firmware version link not clickable in Server Landing Page(SCGCQ01905815)
 - After converting JBOD drives to UG drives, "action successful" message not displayed and incorrect PD actions listed(SCGCQ01927915)
 - LSA Client: In Remote Discovery page, "servers" call is being made twice(SCGCQ01932106)
 - Incorrect tab listener in login page.(SCGCQ01932725)
 - LSA 7.9: "Personality management" page do not close automatically after launch of "Schedule consistency check" page.(SCGCQ01933812)
 - Fixed: clear and generate snap dump feature should not be displayed if snap dump is disabled(SCGCQ01936663)
 - WG: Memory Leak issue with LSA build : 5.035.000.000(SCGCQ01937263)
 - Clear configuration message not indicating about discards pinned cache(SCGCQ01951802)
 - WG:GUI issues:Controller health text,system message bar,download log, scheduler operation failure & JBOD to UG notifications(SCGCQ01968459)
 - Fixed: LSA 7.9:In presence of 32 GHSPs, advance configuration option is leading to configurable page on iMR card(SCGCQ01969524)
 - LSA_7.9: Issue pertaining to PD offline operation on multiple PD's of a VD(SCGCQ01969611)
 - LSA_7.9: Status code and description are not clear during Unconfigured Bad to Unconfigured Good operation.(SCGCQ01972681)
 - WG: JBOD to UG conversion popup does not show error notification in case there is an OS drive, fails with 400ok though(SCGCQ01973688)
 - WG: Enabling and disabling the alarm multiple times shows error message without error code number(SCGCQ01973701)
 - LSA Server: Returning wrong status code as return value - Status Code and Description implementation(SCGCQ01974131)
 - MR 7.9 Alpha: readForeignCfg: error reading refPd=c!!! aborting operation(SCGCQ01993611)
 - LSA locate time inaccurate(SCGCQ02038270)
 - Aero DBU PA2(LSA	(SCGCQ02065617)
 - No response observed when tried to import Foreign LDs which results is reaching MAX LDs(SCGCQ02082982)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102427)
 - 7.10-LSA: Event ID 457 description ends junk character.(SCGCQ02184221)
 -	(SCGCQ01878801)
 - LSA 7.9: Incorrect value accepted during PD locate and wrong Icon displayed in IE when compared to Chrome.(SCGCQ01901766)
 - LSA server profile shows IT-IR storlib versions.	(SCGCQ01901771)
 - LSA 7.9: Incorrect Filter message displayed, wrong message after max vd and multiple grammatical errors in Licence document.(SCGCQ01901773)
 - LSA 7.9: Server search list no more displayed if the user press enter or move the cursor.(SCGCQ01905850)
 - PH10 PA - LSA - Logout option not presented when drop down arrow is clicked(SCGCQ01934763)
 - WG: Status code description is not proper(SCGCQ01942172)
 - LSA 7.9: After converting JBOD drives to UG drives, "action successful" message not displayed and incorrect PD actions listed(SCGCQ01949787)
 - LSA 7.9 alpha:LSA Status code enhancements - Individual operations related issues(SCGCQ01961403)
 - WG: GUI issues: 404 due to unavailable image, VMware login error notification when server down, FW update notification(SCGCQ01968407)
 - WG: VD options are not getting updated after the expanding the VD on selecting the VD while VD expansion is in progress(SCGCQ01973705)
 - LSA PR (SCGCQ01907025: Existing administrator authorization fails with Error code:49: invalid credentials.(SCGCQ02023562)
 - WG_7.10: Enclosure location shows blank for the NVME drives	(SCGCQ02076920)
 - LSA - AWB option is coming for CC VD with Rambler card when user try to modify VD properties if CC VD goes offline/degraded(SCGCQ02184389)
 - WG: Table formatting is not proper in controller console page(SCGCQ01875668)
 - Fixed: Adding more than 1 vd on a hole & adding more than 1 vds on existing DG fails in LSA(SCGCQ01940161)
 - when clear drive operation is aborted on foreign Pds, the Pds are seen as UG as well listed under DG(SCGCQ01944435)
 - Fixed: Download DA/SA server report when downloaded remotely from Gateway(SCGCQ01969625)
 - MRSA: Enclosure count updated wrong in Server profile page(SCGCQ01976923)
 - For 7.10 LSA with max VD configuration, with foreign configuration present LSA unable to import or reject or proper message should displayed. Can you please look into this issue.(SCGCQ02184326)
 - LSA 7.9: Select and un-select button does not work after minimizing the tab(SCGCQ01978952)
 - Fixed: Blank page shown on trying to login 2nd time VMware using Manage server page(SCGCQ02035380)
 - LSA : Getting wrong data about max number of PD support for R6 while doing RLM(SCGCQ02184391)
 - SCGCQ01134787: GUI’s are required to be localized for the following languages: English, French, Italian, German, Spanish, and Japanese(SCGCQ01840448 port of SCGCQ01134787)
 - Security Standalone requirements for LSA Server code changes	(SCGCQ01854924 port of SCGCQ01399720)
 - Megacell Status Support - Phase2 (Caching and Controller health Status(SCGCQ01857649 port of SCGCQ01598200)
 -	(SCGCQ01868298 port of SCGCQ01564366)
 - Megacell Status Support - Phase2 (Caching and Controller health Status(SCGCQ01869716 port of SCGCQ01598139)
 - IR3: Drive count is 0 and no PDs were listed in Controller console Page--> Drives Tab(SCGCQ01962269 port of SCGCQ01898255)
 - WG: After adding an VMware server manually to remote discovery page, the " GO to manage server page is not clickable"(SCGCQ01963211 port of SCGCQ01940852)
 - LSA - Not able to import other foreign configs if user have SED drive which is in foreign(SCGCQ01963213 port of SCGCQ01937406)
 - MRSA : NO option to go forward while configuring the VD`s if all drives are in JBOD.(SCGCQ01963214 port of SCGCQ01902964)
 - Clear configuration message not indicating about discards pinned cache(SCGCQ01963766 port of SCGCQ01951802)
 - WG: LSA manage link speed pane does not provide any info to user on which port is connected/disconnected(SCGCQ01963971 port of SCGCQ01512320)
 - when clear drive operation is aborted on foreign Pds, the Pds are seen as UG as well listed under DG(SCGCQ01965222 port of SCGCQ01944435)
 - Scheduler API call in not working in standalone mode of installation(SCGCQ01965612 port of SCGCQ01961390)
 - RWC3 Linux License Agreement and Desktop Shortcut Is for LSI instead of RWC3 (Windows RWC3 is okay(SCGCQ01971208 port of SCGCQ01942985)
 - LSA 7.9 alpha:Incomplete foreign found after unlocking the Locked foreign config during the Reconstruction.(SCGCQ01971235 port of SCGCQ01962216)
 - LSA 7.9 Foreign config Import doesnt work correctly with Raid 1 VD(SCGCQ01972651 port of SCGCQ01966687)
 - Fixed: missing Event description for new events was pausing LSA(SCGCQ01991449 port of SCGCQ01980570)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx(SCGCQ02000919 port of SCGCQ01929667)
 - (SCGCQ01993697: MR7.9 Alpha: RWC3 (LSA(SCGCQ02002118 port of SCGCQ01993697)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx(SCGCQ02007219 port of SCGCQ01929667)
 - (SCGCQ01993697: MR7.9 Alpha: RWC3 (LSA(SCGCQ02015378 port of SCGCQ01993697)
 - WG: Enabling or disabling SSD guard fails with error code "1", Description: "SSD Guard Disable Failure "(SCGCQ02016686 port of SCGCQ02009718)
 - Memory Leak issues LSA Build (7.009.007.00(SCGCQ02030825 port of SCGCQ02006229)
 - PH11 PA LSA - Attached Drive info not displayed under controller page(SCGCQ02031020 port of SCGCQ02023407)
 - LSA Client : Trigger and Download Snap Dump from application	(SCGCQ02032043 port of SCGCQ01917087)
 - LSA 7.9:Clear config is successful when OS Pd and other PDs are in jbod state(SCGCQ02032206 port of SCGCQ02021372)
 - WG: No Action Successful notification shown on Drive erase(single Drive(SCGCQ02032617 port of SCGCQ01941129)
 -(SCGCQ02034407 port of SCGCQ02030621)
 -(SCGCQ02034409 port of SCGCQ02030621)
 - LSA 7.9:Send Email functionality of LSA is not working.(SCGCQ02034511 port of SCGCQ01998245)
 - PH11 PA - LSA IT - Copyright info needs to be updated(SCGCQ02035246 port of SCGCQ02034466)
 - WG:Unable to perform Enable SCSI Unmap operation when DHSP is removed from the VD.(SCGCQ02036726 port of SCGCQ02035226)
 - Logical drives are listed in the GUI when all the drives are pulled out(SCGCQ02042290 port of SCGCQ01976929)
 - Memory Leak issues LSA Build (7.009.007.00(SCGCQ02042291 port of SCGCQ02006229)
 - LSA 7.9:LSA Gray page is seen when multiple VDs of multiple DGs are deleted.(SCGCQ02042976 port of SCGCQ01983080)
 - LSA_7.9: Issue pertaining to PD offline operation on multiple PD's of a VD(SCGCQ02043600 port of SCGCQ01969611)
 - LSA locate time inaccurate(SCGCQ02043617 port of SCGCQ02038270)
 - LSA locate time inaccurate(SCGCQ02043619 port of SCGCQ02038270)
 - Fixed: Can't Create 5 VDs R6 using 4 pds with AWB,ARA policy with different strip size(SCGCQ02043629 port of SCGCQ01970007)
 - Fixed: "All the listed drives cannot be mixed" displayed while creation of R0 with "select all" option.(SCGCQ02043631 port of SCGCQ01979083)
 - Fixed: when SasSata-mixing-policy is set to false vd creation options are not getting populated(SCGCQ02043632 port of SCGCQ01880184)
 - LSA Client: MRSA: Crash when tried to flash corrupt firmware(SCGCQ02043796 port of SCGCQ02043781)
 - WG: Instance Secure Erase is not giving any action indication(SCGCQ02044624 port of SCGCQ01942452)
 - WG: VD options are not getting updated after the expanding the VD on selecting the VD while VD expansion is in progress(SCGCQ02044809 port of SCGCQ01973705)
 - Issues wrt the linux installer script	(SCGCQ02044832 port of SCGCQ01879303)
 - LSA 7.9:when multiple Vds are added on the existing DG, there is inconsistency in the Vd name(SCGCQ02044903 port of SCGCQ01978171)
 - WG: After creating VD from server summary page opens empty JBOD conversion page, issue pertaining sector size in filter(SCGCQ02046361 port of SCGCQ01957078)
 - No help option available for Megacell option whenever it calls for “Needs Attention” in LSA(SCGCQ02050529 port of SCGCQ02022983)
 - LSA - Patrol Read maxconcurrentpd count in LSA should be inline with FW	(SCGCQ02053882 port of SCGCQ02040516)
 - LSA 7.9: Incorrect Filter message displayed, wrong message after max vd and multiple grammatical errors in Licence document.(SCGCQ02055506 port of SCGCQ01901773)
 -(SCGCQ02055834 port of SCGCQ01878801)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02055865 port of SCGCQ02035322)
 - (SCGCQ02003711: Add default HTTPS to RWC3(SCGCQ02057603 port of SCGCQ02003711)
 - LSA Standalone - enhanced authentication/authorization (Windows(SCGCQ02064849 port of SCGCQ01984624)
 - LSA Server: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02067442 port of SCGCQ02045048)
 - LSA Windows Readme: Update the LSA Windows Read me with the enhanced Silent installation instructions(SCGCQ02070858 port of SCGCQ02070840)
 - LSA: Read_only_access group users are given administrator privileges(SCGCQ02080158 port of SCGCQ02078614)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02084533 port of SCGCQ02035322)
 - Fixed: Calculation to get possible range for RLM	(SCGCQ02087354 port of SCGCQ02070841)
 - Fixed: Calculation to get possible range for RLM	(SCGCQ02093538 port of SCGCQ02070841)
 - Fixed: Allowed Simple config parameters are not displayed(SCGCQ02094990 port of SCGCQ02076799)
 - LSA is not showing PD Connector information properly with passive backaplane	(SCGCQ02096769 port of SCGCQ02096766)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102495 port of SCGCQ02102427)
 - Application Crash when tried to create a LD with 15 character length	(SCGCQ02113222 port of SCGCQ02112041)
 - LSA wrongly treats "MaxAHCIDev" as "Max SATA supported drives" in profile info.(SCGCQ02119286 port of SCGCQ02119031)
 - Application Crash when tried to create an LD with 15 character length(SCGCQ02121748 port of SCGCQ02111930)
 - WG 7.11: Simple configuration fails when multiple vds are created.(SCGCQ02125582 port of SCGCQ02125538)
 - Configuration options is not getting updated when we change the personality(SCGCQ02154818 port of SCGCQ02124500)
 - Only 1 drive is displayed although more than 1 drive has opted for Dedicated drive(SCGCQ02154840 port of SCGCQ02113971)
 - Aero DBU PA5(LSA): Secure jbod option is not shown for the FDE capable jbod drive in LSA(SCGCQ02162725 port of SCGCQ02149233)
 - LSA service/Nginx service is stopping after few hours and WebGUI is not responding in RHEL 8.0 OS(SCGCQ02172192 port of SCGCQ02151342)
 - LSA Aero IT: LSA installation with "start from now" option is throwing error code:9098 in event logs.(SCGCQ02172199 port of SCGCQ02121896)
 - Event ID 610 and 611 are empty(SCGCQ02172244 port of SCGCQ02166100)
 - Generic LSA w/MRSA backend (Snap 3(SCGCQ01818695 port of SCGCQ01532391)
 - IML event customization (Mesa Verde(SCGCQ01837799 port of SCGCQ01625911)
 - Dual Firmware Image Support on Controller Flash for Recovery	(SCGCQ01847635 port of SCGCQ01320454)
 - LSA : Dqueue logs need to be fetched in smaller chunks by the applications(SCGCQ01860906 port of SCGCQ01571368)
 - SSD WEAR GAUGE Support(SCGCQ01891668 port of SCGCQ01890543)
 - OPAL drives fail to import when entering wrong security key then right security key after power cycle(SCGCQ01915862 port of SCGCQ01905192)
 - WG: Enclosure:Slot number is not displaying in Ascending or Descending order, if other columns are clicked first.(SCGCQ01963764 port of SCGCQ01874775)
 - LSA Client: GWT Popup panels are morphing the GWT fixed panels(SCGCQ01965636 port of SCGCQ01943617)
 - WG: LSA services crashes while adding the manually discovered VMware server to the manage server list(SCGCQ01967858 port of SCGCQ01918692)
 - In JBOD personality LSA service getting stopped when user change JBOD to UG(SCGCQ01971507 port of SCGCQ01971368)
 - (SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon	(SCGCQ01990298 port of SCGCQ01856350)
 - (SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01990346 port of SCGCQ01829895)
 - (SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon	(SCGCQ02001873 port of SCGCQ01856350)
 - LSA: LSA Crashes on updating firmware and doing OCR, not able to recover further	(SCGCQ02034499 port of SCGCQ02032031)
 - Shenandoah_MRSA: Listing SAS SSD drive while trying to migrate an array configured with HDD's.(SCGCQ02042096 port of SCGCQ01976926)
 - LSA 7.9:Secure using FDE option is not shown for VD(using OPAL)(SCGCQ02042097 port of SCGCQ01993099)
 - Cacheinit should not issue READ_AFTER_IMPORT dcmd id no foreign pd present.(SCGCQ02042292 port of SCGCQ02038386)
 - WG 7.8: Dedicatedhotspare and Replace missing drive tables are combined in LSA(SCGCQ02043598 port of SCGCQ01888233)
 - fixed: LSA doesnt consider Copyback state while counting configured pds.(SCGCQ02043630 port of SCGCQ01979598)
 - Shenandoah_Aero_LSA: LSA crashes while initiating OCR on A0 controller(SCGCQ02043856 port of SCGCQ02000446)
 - LSA 7.9 alpha:Disable data protection option is seen for non-secured & secured VD in presence of locked foreign PD(SCGCQ02043858 port of SCGCQ01960300)
 -(SCGCQ02043859 port of SCGCQ01927978)
 - WG: GUI issues: 404 due to unavailable image, VMware login error notification when server down, FW update notification(SCGCQ02044679 port of SCGCQ01968407)
 - WG: no success or failure message is shown on updating the drive secuirty key(SCGCQ02044688 port of SCGCQ01970452)
 - MRSA: Crash when tried to flash corrupt firmware(SCGCQ02045015 port of SCGCQ02040739)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02055880 port of SCGCQ02035322)
 - Status reports as failed although firmware is updated successfully(SCGCQ02058472 port of SCGCQ01983031)
 - LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online".(SCGCQ02081267 port of SCGCQ01838943)
 - LSA: VD actions performed using storcli not reflected under LSA's Virtual drive tab(SCGCQ02084746 port of SCGCQ02078435)
 - NVMe Drive interface type should be shown as "NVMe" instead of "PCIe"(SCGCQ02100198 port of SCGCQ02096718)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102571 port of SCGCQ02102427)
 - Fixed: Snap dump file(SCGCQ02105149 port of SCGCQ02080184)
 - WG 7.11:Jbod Locked foreign config details are empty under foriegn configuration operation.(SCGCQ02112529 port of SCGCQ02112203)
 - WG: LSA incorrectly notifies "Incomplete or Non-Importable foreign configuration found" instead of max supported configuratio(SCGCQ02162724 port of SCGCQ02149353)
 - WG: LSA shows the same connector for both backplane and enclosure in properties pane(SCGCQ02179358 port of SCGCQ02167855)
 - Drive capacities displayed should match the HPE drive capacity labels.(SCGCQ01869701 port of SCGCQ01246226)
 - Support newly added Sanitize event for cache update.(SCGCQ01869717 port of SCGCQ01740786)
 - WG: with loop back SMTP Ip, only the test email is received to broadcom mail id, able to add duplicate email id to email tab(SCGCQ01918643 port of SCGCQ01880101)
 -(SCGCQ01925516 port of SCGCQ01714322)
 - LSA needs to Handle when controller is in safe Mode(SCGCQ01963207 port of SCGCQ01838234)
 - WG: Memory Leak issue with LSA build : 5.035.000.000(SCGCQ01965387 port of SCGCQ01937263)
 - LSA Server: LSA needs to Handle when controller is in safe Mode(SCGCQ01967491 port of SCGCQ01949074)
 - WG MR 7.7 alpha:Lsa does not update the PD(part of r0 volume(SCGCQ01970440 port of SCGCQ01752969)
 - LSA 7.9 alpha:issues pertaining to migration from degraded Unmpa R5 to R0(SCGCQ01971232 port of SCGCQ01966275)
 - In JBOD personality LSA service getting stopped when user change JBOD to UG(SCGCQ01974074 port of SCGCQ01971368)
 - PH11 PA - LSA IT - Copyright info needs to be updated(SCGCQ02035247 port of SCGCQ02034466)
 - LSA Client: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02067299 port of SCGCQ02044922)
 - RWC3 Windows Readme contains IR3 controllers under supported controllers list(SCGCQ02082904 port of SCGCQ02081038)
 - WG 7.10: LSA crashes when generate snapdump or dowload snap dump operations are performed on direct agent(SCGCQ02099466 port of SCGCQ02094537)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02103244 port of SCGCQ02102427)
 - Fixed: R00 max pd limit is changed to be aligned with fw requirement(SCGCQ02116793 port of SCGCQ02108807)
 - LSA - While doing RLM from R6 to R1, odd number of drives option is coming for R1(SCGCQ02118270 port of SCGCQ02108817)
 -	(SCGCQ02154813 port of SCGCQ02142063)
 - Fixed: parity disk count was missing in algorithm to calculate minimum VD(SCGCQ02154869 port of SCGCQ02139246)
 - WG: LSA does not update on Clearing the config from server summary page in presence of degraded config(SCGCQ02160137 port of SCGCQ02154073)
 - LSA - upgrade installshield(SCGCQ02164387 port of SCGCQ02087375)
 - Download Server Report – change this to Download Support Log and Remove Download Diagnostics	(SCGCQ01824401 port of SCGCQ01388152)
 - LSA No Login (HPE Snap 3 SOW	(SCGCQ01840451 port of SCGCQ01512600)
 - Sanitize Support (HPE SNAP 3	(SCGCQ01857424 port of SCGCQ01564367)
 - IML event customization (Mesa Verde(SCGCQ01868281 port of SCGCQ01625911)
 - LSA is allowing to delete OS VD.	(SCGCQ01923557 port of SCGCQ01873420)
 - LSA - Not able to import other foreign configs if user have SED drive which is in foreign(SCGCQ01942179 port of SCGCQ01937406)
 - WG: VD creation page does not show VD count and capacity of VD that can be created using unmap drive	(SCGCQ01962278 port of SCGCQ01952143)
 - WG: LSA services crashes while adding the manually discovered VMware server to the manage server list(SCGCQ01967919 port of SCGCQ01918692)
 - WG: Instance validation for PD and Configuration service GET fails with " isSupportedByFW' & 'securityType' was unexpected(SCGCQ01998976 port of SCGCQ01998305)
 - (SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ02001889 port of SCGCQ01829895)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx(SCGCQ02007218 port of SCGCQ01929667)
 - (SCGCQ02003711: Add default HTTPS to RWC3(SCGCQ02007520 port of SCGCQ02003711)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02053863 port of SCGCQ02035322)
 - Fixed: WG: Instance validation for Controller Get fails(SCGCQ02062148 port of SCGCQ02035158)
 - WG: snapdump downloaded after host triggered snapdump is not in zip file format(SCGCQ02089526 port of SCGCQ02084515)
 - Fixed: Calculation to get possible range for RLM	(SCGCQ02093240 port of SCGCQ02070841)
 - LSA couldn't install successful in RHEL 8.0 without OpenSLP installed(SCGCQ02105326 port of SCGCQ02103116)
 - RHEL8- LSA reports warnings during Service restart after reboots, remote discovery page does not list any server other server(SCGCQ02159794 port of SCGCQ02144606)
 - : Support PCI Slot and Serial Number in(SCGCQ01822600 port of SCGCQ01351434)
 - MRSA:Default strip size should be 64KB for SSD(SCGCQ01825959 port of SCGCQ01406706)
 - Change the word data protection to Data Integrity Field(SCGCQ01839302 port of SCGCQ01827434)
 - Expander support for LSA(SCGCQ01839611 port of SCGCQ01372657)
 - (SCGCQ01681996: Copy back option should not prompt for already copyback progress PD.(SCGCQ01840438 port of SCGCQ01681996)
 - Drive capacities displayed should match the HPE drive capacity labels.(SCGCQ01847392 port of SCGCQ01134783)
 -(SCGCQ01943786 port of SCGCQ01932181)
 - fixed: logout of indirect agent causing gateway session to expire(SCGCQ01996636 port of SCGCQ01969806)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx	(SCGCQ02000918 port of SCGCQ01929667)
 - Shenandoah_Aero_LSA: LSA crashes while initiating OCR on A0 controller(SCGCQ02012079 port of SCGCQ02000446)
 - MR 7.9 Alpha: readForeignCfg: error reading refPd=c!!! aborting operation(SCGCQ02015391 port of SCGCQ01993611)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102497 port of SCGCQ02102427)
 - LSA is using old PDL for send Feedback option(SCGCQ02133579 port of SCGCQ02133392)
 - WG: Making an offline drive of a DG to online does not work in controller health pane, no POST call for same is initiated(SCGCQ02144596 port of SCGCQ02139321)
 - (SCGCQ01399721: Hercules :HPE: Security Standalone requirements for LSA Linux 32/64 bit Installer changes(SCGCQ01827380 port of SCGCQ01399721)
 - Support PCI Slot and Serial Number in Mesa Verde	(SCGCQ01839058 port of SCGCQ01349491)
 - Capacity Unit Changes for VD in LSA Client from GB to GIB(SCGCQ01859426 port of SCGCQ01708968)
 -	(SCGCQ01864209 port of SCGCQ01763927)
 - LSA 7.8: Unable to launch LSA from different web server port after LSA upgrade.(SCGCQ01904366 port of SCGCQ01901758)
 - IML event customization (Mesa Verde(SCGCQ01837623 port of SCGCQ01601601)
 - Megacell Status Support (SNAP3(SCGCQ01868328 port of SCGCQ01566234)
 -	(SCGCQ01869156 port of SCGCQ01320455) -
 - WG 7.11:Enable scsi unmap checkbox at advance config page is grayed out when enable/disable operation is performed.(SCGCQ02154812 port of SCGCQ02118865)
 - Security Standalone requirements for LSA Server code changes(SCGCQ01854929 port of SCGCQ01399722)
 - Expander support for LSA	(SCGCQ01855600 port of SCGCQ01376077)
 - LSA Not allowing to clear/Import foreign configuration.(SCGCQ01869616 port of SCGCQ01849749)
 - Capacity Unit Changes for VD in LSA Server(SCGCQ01869745 port of SCGCQ01708881)
	
EnhancementRequests (35)
 - Enhance Status Code and Status description(SCGCQ01825960)
 - LSA Internal Status code and Description(SCGCQ01850884)
 -(SCGCQ01949651)
 - Branding tool and Health (OS eventing(SCGCQ01960398)
 - Ubuntu LSA support(SCGCQ02042072)
 - LSA Server: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02045048)
 - Branding tool and Health (OS eventing(SCGCQ02045972)
 - API changes for NVMe speed and width changes(SCGCQ02053667)
 - API changes for linkconfig interface	(SCGCQ02053671)
 - Change the parent directory name to "HPEMRSA" in the windows(SCGCQ02055912)
 - Implement Changes for LSA Light weight agent On ESXi 64 bit Platform(SCGCQ02066385)
 - Add disableOffloadNum field in MR_SNAPDUMP_PROPERTIES struct(SCGCQ02125252)
 - API changes for a better presentation of Atlas to tools(SCGCQ02149380)
 - Snap Dump ClearAll Method logging event(SCGCQ02157359)
 -(SCGCQ02162699)
 - Create an event for DDF config clear failed event.(SCGCQ02173513)
 - WG: LSA "Feedback" UI enhancements(SCGCQ01401503)
 - LSA Client : Trigger and Download Snap Dump from application(SCGCQ01917087)
 - Implemented: Allow user to generate snap-dump in firmware and download it(SCGCQ01917294)
 - Client: Ubuntu LSA support(SCGCQ02042121)
 - LSA Client: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02044922)
 - 64 Bit SLIR3 library to Support for VMWARE ESXi 6.7+	(SCGCQ02048704)
 - MR API: Add support bits for currentSpeed and clkMode(SCGCQ02132334)
 - Adding NVACHE messages indicate when SLC format has started and completed.(SCGCQ02137048)
 - Add new topology device type for Atlas switch(SCGCQ02150637)
 - LSA need to show complete Serial Number and Model Name for NVMe drives(SCGCQ01920105)
 - LSA Standalone - enhanced authentication/authorization (Windows(SCGCQ01984624)
 - SSD WEAR GAUGE Support(SCGCQ01890543)
 - LSA should upgrade to 1.0.2q (OpenSSL and Nginx(SCGCQ01929667)
 - 64 Bit SLIT library Support for VMWARE ESXi 6.7+	(SCGCQ02019271)
 - LSA: SSD WEAR GAUGE Support(SCGCQ01890612)
 - MRSA One Click Support Client support(SCGCQ01949650)
 - LSA Server: Scheduler changes to fit with latest LSA status code(SCGCQ01857843)
 - Enhance Status Code and Status description(SCGCQ01868342)
 - LSA Server: Aero FW simplification - Changes for disable least latency mode(SCGCQ01944689)

005.047.000.000 - Moderate Impact
---------------

Defects:
 -WG:Memory leak issues when the system is not idle ( Running the GUI suite when the memory leak test is in progress).(SCGCQ01680714)
 -Fixed: nvme is allowed to mix with sas /sata.(SCGCQ01762948)
 -WG:[intermittent] LSA page goes blank if we click on Drive tab and then immediately click on view serer profile.(SCGCQ01747490)
 -WG MR 7.7 alpha:Lsa does not update the PD(part of r0 volume) status once the PD is made online from offline(SCGCQ01752969)
 -WG MR 7.7 al:LSA allows to create simple configuration in presence of Unconfigured bad drive and rest of the drives in jbod.(SCGCQ01763742)
 -WG MR 7.7 alpha: LSA displays wrong connector & path info for drives when enclosure is connected in wide port (x8 connection).(SCGCQ01764794)
 -WG: JBOD conversion popup appears multiple times after converting all the drives to UG and clicking on Continue button.(SCGCQ01737550)
 -LSA locate time inaccurate.(SCGCQ02038270)
 -LSA PR SCGCQ01907025: Existing administrator authorization fails with Error code:49: invalid credentials.(SCGCQ02023562)
 -LSA: Authenticated User group is given Read only privileges after adding Authenticated Users to full_access_groups..(SCGCQ02045735)
 -LSA: VD actions performed using storcli not reflected under LSA's Virtual drive tab.(SCGCQ02078435)
 -LSA: Read_only_access group users are given administrator privileges.(SCGCQ02078614)
 -RWC3 Windows Readme contains IR3 controllers under supported controllers list.(SCGCQ02081038)
 -Fixed: R00 max pd limit is changed to be aligned with fw requirement.(SCGCQ02108807)
 -LSA - While doing RLM from R6 to R1, odd number of drives option is coming for R1.(SCGCQ02108817)
 -LSA wrongly treats "MaxAHCIDev" as "Max SATA supported drives" in profile info..(SCGCQ02119031)
 - LSA installation failed on SLES15.(SCGCQ01784699 port of SCGCQ01760620)
 - LSA needs proper message for max config import.(SCGCQ01789100 port of SCGCQ01763411)
 - MRSA Snap 4 : Alpha : LSA provides option of performing an RLM operation on Degraded VD, which fails.(SCGCQ01789156 port of SCGCQ01731931)
 - LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode.(SCGCQ01716625 port of SCGCQ01716622)
 - WG: LSA allows user to replace a drive of a DG with drive on which drive clear is already in progress, GUI issues in popup.(SCGCQ01810649 port of SCGCQ01803341)
 - MR7.7: Removal of UNMAP support for JBOD.(SCGCQ01813086 port of SCGCQ01813078)
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config.(SCGCQ01816649 port of SCGCQ01686080)
 - MR7.6: LSA crashed with a mouse click on VD.(SCGCQ01816428 port of SCGCQ01641760)
 - LSA needs proper message for max config import.(SCGCQ01813925 port of SCGCQ01764977)
 - C480-M5: LSA downloaded event log needs better decoding.(SCGCQ01828830 port of SCGCQ01321211)
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events.(SCGCQ01826237 port of SCGCQ01761830)
 - LSA-4.1 : Array details are shown in LSA for the partial foreign config .(SCGCQ01850405 port of SCGCQ01818828)
 - Tape drive state is blank when connected with 9400-8E card from LSA drives tab.(SCGCQ01851980 port of SCGCQ01851906)
 - SCGCQ01841280: Before importing foreign CC VD, model number of SSD is not coming in LSA.(SCGCQ01851919 port of SCGCQ01841280)
 - UG LSA 7.8 PA2:Incomplete foreign VD is seen when Clear foreign config is performed.(SCGCQ01851155 port of SCGCQ01849681)
 - LSA Not allowing to clear/Import foreign configuration.(SCGCQ01860933 port of SCGCQ01849749)
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01880125 port of SCGCQ01874487)
 - LSA login to ESXi 6.x servers fails in SLES 15 OS..(SCGCQ01880123 port of SCGCQ01876091)
 - handling the session management.(SCGCQ01892868 port of SCGCQ01829897)
 - WG: VMware server takes too long to discover in remote discovery page : nearly 20 minutes.(SCGCQ01891168 port of SCGCQ01889547)
 - Handling the set text mechanism in client.(SCGCQ01886532 port of SCGCQ01850387)
 - Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016.(SCGCQ01897181 port of SCGCQ01841473)
 - Fixed: Crash when pressing back button after logout.(SCGCQ01892905 port of SCGCQ01865309)
 - LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap.(SCGCQ01897266 port of SCGCQ01818960)
 - LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online" .(SCGCQ01898344 port of SCGCQ01838943)
 - fixed: LSA fails to create RAID 10 with large number of drives.(SCGCQ01901767 port of SCGCQ01833469) 
 - Fixed: unblock LSA login on ESXi 6.7 U1.(SCGCQ01901774 port of SCGCQ01866289)
 - Change tools to report drives attached to HBAs as JBOD instead of UGOOD.(SCGCQ01898263 port of SCGCQ01802344)
 - Fixed: Auto Span Adjust with having >64 disks is not correct..(SCGCQ01901754 port of SCGCQ01827404)
 - CC VD creation option is coming in LSA when the CC VD (SATA SSD) is in foreign config.(SCGCQ01897144 port of SCGCQ01817275)
 - Update the Windows Server 2019 OS name in LSA.(SCGCQ01897178 port of SCGCQ01866322)
 - Remove un printable characters from LSA log.(SCGCQ01901769 port of SCGCQ01901760)
 - Server: LSA GUI Not Updating Security Key Info.(SCGCQ01897099 port of SCGCQ01761801)
 - OPAL drives fail to import when entering wrong security key then right security key after power cycle.(SCGCQ01915861 port of SCGCQ01905192)
 - [CISCO]LSA shows previously set security key (M3g@raid) during importing secured foreign config JBOD (TCG Enterprise SED).(SCGCQ01921581 port of SCGCQ01878346)
 - LSA fails to start initialization on EPD if it has DDF.(SCGCQ01921583 port of SCGCQ01849522)
 - (SCGCQ01921684 port of SCGCQ01841361)
 - MR7.8 Foreign import from 7.7 to 7.8 with unmap VD and non unmap DHS does not alert user with a critical message/event.(SCGCQ01921836 port of SCGCQ01876230)
 - LSA 7.8:LSA provides Instant secure erase option for Locked UG BAD drives..(SCGCQ01904075 port of SCGCQ01893304)
 - LSA 7.8: Unable to launch LSA from different web server port after LSA upgrade..(SCGCQ01904345 port of SCGCQ01901758)
 - .(SCGCQ01920699 port of SCGCQ01808698)
 - LSA: Ventura B0: BIOS Flashing Failure Observed in EFI Storcli and Multiple Tries Causes UART Unresponsive.(SCGCQ01921839 port of SCGCQ01829669)
 - (SCGCQ01921842 port of SCGCQ01803373SCGCQ01803373: WG: LSA service crashes on downloading support logs in case of Linux 64 bit OS)
 - LSA does not show Secure Erase option for foreign secured JBOD drive-CLI works(SCGCQ01920701 port of SCGCQ01916249)
 - .(SCGCQ01920924 port of SCGCQ01818618)
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon.(SCGCQ01921819 port of SCGCQ01856350)
 - WG: LSA provides option of Secure using FDE if non encrypted r1 VD with secure drive is assigned with DHSP,.(SCGCQ01915812 port of SCGCQ01906914)
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01921592 port of SCGCQ01829895)
 - LSA 7.8:Import option is given for the Incomplete foreign VD.(SCGCQ01921678 port of SCGCQ01829895)
 - LSA 7.8:Import option is given for the Incomplete foreign VD.(SCGCQ01921678 port of SCGCQ01865420)
 - LSA is allowing to delete OS VD.(SCGCQ01921689 port of SCGCQ01873420)
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01921919 port of SCGCQ01856350)
 - WG: LSA allows to remove the data drive during the RLM from single drive R0 and allows migrate to R0 with no drives DESCRIPTION OF ISSUE(SCGCQ01921580 port of SCGCQ01823858)
 - Fixed: Advance configuration operation should be greyed out if max pds are already configured(SCGCQ01922015 port of SCGCQ01850445)
 -WG: LSA does not notify user on OS VD present if multiple VDs are selected and with non OS VD is selected first(SCGCQ01928961 port of SCGCQ01926674 )
 - LSA Server: Populate the Drive Sector Size while reading the LD MFI command.(SCGCQ01930623 port of SCGCQ01926876)
 - WG: VMware server takes too long to discover in remote discovery page : nearly 20 minutes.(SCGCQ01961510 port of SCGCQ01889547)
 - Summary: Gateway LSA is not responding in SLES 12 64bit(SCGCQ01980553 port of SCGCQ01979137)
 - Cannot use Special Characters in Domain Name for LSA Login(SCGCQ01789161 port of SCGCQ01745768)
 - Optimize the operation areas of UI to add “on demand” call and increase the performance(SCGCQ01792860 port of SCGCQ01746630)
 - Add sorter on individual panel's header(SCGCQ01792967 port of SCGCQ01614993)
 - SCGCQ01761197: Handle Progress events without initiating further api call from Client.(SCGCQ01793020 port of SCGCQ01761197)
 - LSA Server: Enhance view server profile(SCGCQ01793119 port of SCGCQ01613889)
 - Add a way to move from Server / Controller dashboard to Login / Remote Server Discovery Page.(SCGCQ01793314 port of SCGCQ01760616)
 - LSA Client : GUI User Interface to display snap dump details and download snap dump.(SCGCQ01788693 port of SCGCQ01788622)
 -GUI Performance improvement by reducing the GUI binary size.(SCGCQ01791174 port of SCGCQ01484572)
 - WG: Clicking on help links anywhere in LSA page for VMware leads to "404-not found" page.(SCGCQ01791205 port of SCGCQ01594101)
 - LSA Server: Client Logging(SCGCQ01793221 port of SCGCQ01745790)
 - Enhance Action menu of individual and group element(SCGCQ01793250 port of SCGCQ01606850)-
 - Add Select All / Un-Select All option to dashboard tables.(SCGCQ01793004 port of SCGCQ01580899)
 - SCGCQ01761197: Handle Progress events without initiating further api call from Client.(SCGCQ01793081 port of SCGCQ01761224)
 - WG MR 7.7 Alpha:Foreign configuration pane does not show details for foreign dedicated hotspare drive.(SCGCQ01798297 port of SCGCQ01745770)
 - Use scheduler call for heavy operations Part 2.(SCGCQ01792861 port of SCGCQ01746649)
 - SCGCQ01583133: Inconsistency of login dialog box in Manageserver page and Remote discovery page(SCGCQ01793098 port of SCGCQ01583133)
 - Fixed: LSA allows the user to attempt a 3 drive RAID6 VD creation (via RAID60).(SCGCQ01798511 port of SCGCQ01687523)
 - SCGCQ01631835: WG: error log and Access log consume entire OS file system space (6.3 GB and 2.6 GB respectively)(SCGCQ01798635 port of SCGCQ01631835)
 - LSA: SnapDump Implementation(SCGCQ01788680 port of SCGCQ01786658)
 - Enhance Properties panel of Individual elements.(SCGCQ01792093 port of SCGCQ01613898)
 - Handle Progress events without initiating further api call from Client.(SCGCQ01792974 port of SCGCQ01761196)
 - LSA Client Logging.(SCGCQ01792995 port of SCGCQ01752841)
 - LSA Client: Enhance view server profile(SCGCQ01793196 port of SCGCQ01613529)
 - LSA: SnapDump Implementation.(SCGCQ01793838 port of SCGCQ01786658)
 - (SCGCQ01798366 port of SCGCQ01628367)
 - Implemented: LSA: Disable Cached IO option during VD creation(SCGCQ01798387 port of SCGCQ01697006)
 - LSA Server: Optimize the operation areas of UI to add “on demand” call and increase the performance.(SCGCQ01793279 port of SCGCQ01745789)
 - Activity to check-in Auto-BST files to 7.8 streams.(SCGCQ01794950 port of SCGCQ01793057)
 - SCGCQ01595244: WG: issues pertaining to lsa logs file generation in VMware.(SCGCQ01798451 port of SCGCQ01595244)
 - Adding filters to the PD and VD table.(SCGCQ01625154 port of SCGCQ01614984)
  - MRSA Snap 4 : Alpha : LSA provides option of performing an RLM operation on Degraded VD, which fails.(SCGCQ01798299 port of SCGCQ01731931)
 - WG: Enclosure position is not shown in Progress bar PD details for any enclosure above position index=1 as well as event logs.(SCGCQ01801670 port of SCGCQ01794642)
 - LSA does not update the VD status when Migration is performed from r5(3drives)to r1(2drives).(SCGCQ01818637 port of SCGCQ01803743)
  - LSA 502 Bad gateway is seen when Prepare for removal is performed on 5 drives at a time.(SCGCQ01818638 port of SCGCQ01809413)
 - Adding filters to the PD and VD table.(SCGCQ01807941 port of SCGCQ01614984)
 - Implementation of LW Agent Related Back-end changes.(SCGCQ01801403 port of SCGCQ01591705)
 - Add SCSI Unmap property at PD level.(SCGCQ01813071 port of SCGCQ01732785)
 - SCGCQ01680714: WG:Memory leak issues when the system is not idle ( Running the GUI suite when the memory leak test is in progress).(SCGCQ01818554 por of SCGCQ01680714)
 - WG: Duplicate PD entires of replace Drive listed in PD list of controller console page on sorting the PD list more than twice.(SCGCQ01803785 port of SCGCQ01794631)
 - WG: View more properties pane is overlapped by the progress bar if the progress info is in expanded state.(SCGCQ01803986 port of SCGCQ01763142)
- MR7.7: Removal of UNMAP support for JBOD.(SCGCQ01813180 port of SCGCQ01813078)
 - LSA does not give expand option to perform OCE when one among 2vds is deleted under a DG.(SCGCQ01818631 port of SCGCQ01803722)
 - Unable to import foreign secured VDs with different security key.(SCGCQ01818678 port of SCGCQ01670139)
 - LSA needs proper message for max config import.(SCGCQ01813926 port of SCGCQ01764977)
 - MR7.6: LSA crashed with a mouse click on VD.( SCGCQ01819577 port of SCGCQ01641760)
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config.(SCGCQ01822126 port of SCGCQ01686080)
 -.(SCGCQ01824435 port of SCGCQ01317424)
 -.( SCGCQ01827729 port of SCGCQ01808698)
 - Change tools to report drives attached to HBAs as JBOD instead of UGOOD.(SCGCQ01837518 port of SCGCQ01802344)
 - handling the session management.(SCGCQ01841323 port of SCGCQ01829897)
 - LSA PD slot numbering doesn't not display as ascending order by default(SCGCQ01415337 port of SCGCQ01406115)
 - LSA : Stale entries are coming in DG tab when the VD (failed) is in foreign config(SCGCQ01838336 port of SCGCQ01818953)
 - CC VD creation option is coming in LSA when the CC VD (SATA SSD) is in foreign config(SCGCQ01838335 port of SCGCQ01817275)
 - Cannot use Special Characters in Domain Name for LSA Login(SCGCQ01837786 port of SCGCQ01745768)
 - LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap(SCGCQ01838449 port of SCGCQ01818960)
 - WG: JBOD conversion popup appears multiple times after converting all the drives to UG and clicking on Continue button.(SCGCQ01839325 port of SCGCQ01737550)
 - Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016(SCGCQ01845011 port of SCGCQ01841473)
 - WG:Typo event id : 233, Convert button should get disabled when JBOD to UG Conversion in progress, discrepancy in host icons(SCGCQ01848661 port of SCGCQ01840475)
 - WG MR 7.7 al:LSA allows to create simple configuration in presence of Unconfigured bad drive and rest of the drives in jbod(SCGCQ01847352 port of SCGCQ01763742)
 - LSA Client: Improving visible / working area on elements tab(SCGCQ01839616 port of SCGCQ01837412)
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01879301 port of SCGCQ01874487)
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events(SCGCQ01830499 port of SCGCQ01761830)
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events(SCGCQ01830498 port of SCGCQ01761830)
 - Drive status not displayed in Other Hardware tab(SCGCQ01855592 port of SCGCQ01849636)
 - Fixed: unblock LSA login on ESXi 6.7 U1(SCGCQ01874490 port of SCGCQ01866289)
 - WG:Typo event id : 233, Convert button should get disabled when JBOD to UG Conversion in progress, discrepancy in host icons.(SCGCQ01864285 port of SCGCQ01840475)
 - Tape drive state is blank when connected with 9400-8E card from LSA drives tab.(SCGCQ01852072 port of SCGCQ01851906)
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS..(SCGCQ01869568 port of SCGCQ01829895)
 - LSA Not allowing to clear/Import foreign configuration..(SCGCQ01860931 port of SCGCQ01849749)
 - LSA Client : 7.8 Coverity defects fix.(SCGCQ01865174 port of SCGCQ01837314)
 - Fixed: Auto Span Adjust with having >64 disks is not correct..(SCGCQ01855872 port of SCGCQ01827404)
 - LSA is allowing to delete OS VD.(SCGCQ01883000 port of SCGCQ01873420)
 - Implementation of LW Agent Related Back-end changes.(SCGCQ01801314 port of SCGCQ01591705)
 - LSA is allowing to delete OS VD.(SCGCQ01906734 port of SCGCQ01873420)
 - WG: Software licensing agreement for linux RWC3 build is of Generic Channel(SCGCQ01905909 port of SCGCQ01886563)
 - LSA 7.8: Controller actions menu, action successful message are misplaced and Progress bar and event log info overlaps.( SCGCQ01906795 port of SCGCQ01893511)
 - MR LSA 7.7 : When user has flashed the controller FW for IT card, reboot system message is disappearing within few seconds(SCGCQ01893311 port of SCGCQ01761269)
 -LSA: Ventura B0: BIOS Flashing Failure Observed in EFI Storcli and Multiple Tries Causes UART Unresponsive.(SCGCQ01890993 port of SCGCQ01829669)
 -.(SCGCQ01914269 port of SCGCQ01906844)
 - LSA 7.8: Controller actions menu, action successful message are misplaced and Progress bar and event log info overlaps.(SCGCQ01914265 port of SCGCQ01893511)
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01921950 port of SCGCQ01856350)
 - IR3: Drive count is 0 and no PDs were listed in Controller console Page--> Drives Tab.(SCGCQ01962269 port of SCGCQ01898255)
 - WG: After adding an VMware server manually to remote discovery page, the " GO to manage server page is not clickable"(SCGCQ01963211 port of SCGCQ01940852)
 - LSA - Not able to import other foreign configs if user have SED drive which is in foreign(SCGCQ01963213 port of SCGCQ01937406)
 - MRSA : NO option to go forward while configuring the VD`s if all drives are in JBOD.(SCGCQ01963214 port of SCGCQ01902964)
 - Clear configuration message not indicating about discards pinned cache(SCGCQ01963766 port of SCGCQ01951802)
 - when clear drive operation is aborted on foreign Pds, the Pds are seen as UG as well listed under DG(SCGCQ01965222 port of SCGCQ01944435)
 - Scheduler API call in not working in standalone mode of installation(SCGCQ01965612 port of SCGCQ01961390)
 - LSA 7.9 alpha:Incomplete foreign found after unlocking the Locked foreign config during the Reconstruction.(SCGCQ01971235 port of SCGCQ01962216)
 - WG: Enclosure:Slot number is not displaying in Ascending or Descending order, if other columns are clicked first.(SCGCQ01963764 port of SCGCQ01874775)
 - LSA Client: GWT Popup panels are morphing the GWT fixed panels(SCGCQ01965636 port of SCGCQ01943617)
 - WG: LSA services crashes while adding the manually discovered VMware server to the manage server list(SCGCQ01967858 port of SCGCQ01918692)
 - In JBOD personality LSA service getting stopped when user change JBOD to UG(SCGCQ01971507 port of SCGCQ01971368)
 - LSA needs to Handle when controller is in safe Mode(SCGCQ01963207 port of SCGCQ01838234)
 - WG: Memory Leak issue with LSA build : 5.035.000.000(SCGCQ01965387 port of SCGCQ01937263)
 - LSA Server: LSA needs to Handle when controller is in safe Mode(SCGCQ01967491 port of SCGCQ01949074)
 - LSA 7.9 alpha:issues pertaining to migration from degraded Unmpa R5 to R0(SCGCQ01971232 port of SCGCQ01966275)
 - WG: VD creation page does not show VD count and capacity of VD that can be created using unmap drive(SCGCQ01962278 port of SCGCQ01952143)
 - LSA 7.9 Foreign config Import doesnt work correctly with Raid 1 VD.(SCGCQ01972651 port of SCGCQ01966687)
 - SCGCQ01993697: MR7.9 Alpha: RWC3 (LSA) Uninstall Error: "Option “-x” is deprecated" w/ Linux RHEL 7.6.(SCGCQ02002118 port of SCGCQ01993697)
 - (CSETActivity) - LSA 7.9:Clear config is successful when OS Pd and other PDs are in jbod state.(SCGCQ02032206 port of SCGCQ02021372)
 -.(SCGCQ02034407 port of SCGCQ02030621)
 - LSA locate time inaccurate(SCGCQ02043617 port of SCGCQ02038270)
 - Fixed: when SasSata-mixing-policy is set to false vd creation options are not getting populated(SCGCQ02043632 port of SCGCQ01880184)
 - WG: Instance Secure Erase is not giving any action indication(SCGCQ02044624 port of SCGCQ01942452)
 - WG: VD options are not getting updated after the expanding the VD on selecting the VD while VD expansion is in progress.(SCGCQ02044809 port of SCGCQ01973705)
 - LSA 7.9:when multiple Vds are added on the existing DG, there is inconsistency in the Vd name(SCGCQ02044903 port of SCGCQ01978171)
 - Logical drives are listed in the GUI when all the drives are pulled out(SCGCQ02042290 port of SCGCQ01976929)
 - Memory Leak issues LSA Build (7.009.007.00)(SCGCQ02042291 port of SCGCQ02006229)
 - LSA 7.9:LSA Gray page is seen when multiple VDs of multiple DGs are deleted.(SCGCQ02042976 port of SCGCQ01983080)
 - LSA_7.9: Issue pertaining to PD offline operation on multiple PD's of a VD(SCGCQ02043600 port of SCGCQ01969611)
 - Fixed: Can't Create 5 VDs R6 using 4 pds with AWB,ARA policy with different strip size(SCGCQ02043629 port of SCGCQ01970007)
 - Fixed: "All the listed drives cannot be mixed" displayed while creation of R0 with "select all" option.(SCGCQ02043631 port of SCGCQ01979083)
 - LSA Client: MRSA: Crash when tried to flash corrupt firmware(SCGCQ02043796 port of SCGCQ02043781)
 - Issues wrt the linux installer script(SCGCQ02044832 port of SCGCQ01879303)
 - WG: After creating VD from server summary page opens empty JBOD conversion page, issue pertaining sector size in filter(SCGCQ02046361 port of SCGCQ01957078)
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ02001873 port of SCGCQ01856350)
 - Shenandoah_MRSA: Listing SAS SSD drive while trying to migrate an array configured with HDD's.(SCGCQ02042096 port of SCGCQ01976926)
 - Cacheinit should not issue READ_AFTER_IMPORT dcmd id no foreign pd present.(SCGCQ02042292 port of SCGCQ02038386)
 - WG 7.8: Dedicatedhotspare and Replace missing drive tables are combined in LSA(SCGCQ02043598 port of SCGCQ01888233)
 - fixed: LSA doesnt consider Copyback state while counting configured pds.(SCGCQ02043630 port of SCGCQ01979598)
 - LSA 7.9 alpha:Disable data protection option is seen for non-secured & secured VD in presence of locked foreign PD(SCGCQ02043858 port of SCGCQ01960300)
 -(SCGCQ02043859 port of SCGCQ01927978)
 - WG: GUI issues: 404 due to unavailable image, VMware login error notification when server down, FW update notification(SCGCQ02044679 port of SCGCQ01968407)
 - WG: no success or failure message is shown on updating the drive secuirty key(SCGCQ02044688 port of SCGCQ01970452)
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ02001889 port of SCGCQ01829895)
 - SCGCQ02003711: Add default HTTPS to RWC3(SCGCQ02007520 port of SCGCQ02003711)
 - fixed: logout of indirect agent causing gateway session to expire(SCGCQ01996636 port of SCGCQ01969806)
 - MR 7.9 Alpha: readForeignCfg: error reading refPd=c!!! aborting operation(SCGCQ02015391 port of SCGCQ01993611)
 - LSA Client : Trigger and Download Snap Dump from application(SCGCQ02032043 port of SCGCQ01917087)
 - WG: No Action Successful notification shown on Drive erase(single Drive), Application Version shown as undefined for VMware(SCGCQ02032617 port of SCGCQ01941129)
 - LSA 7.9:Send Email functionality of LSA is not working.(SCGCQ02034511 port of SCGCQ01998245)
 - LSA 7.9:Secure using FDE option is not shown for VD(using OPAL) when Drive security is enabled.(SCGCQ02042097 port of SCGCQ01993099)
 - Shenandoah_Aero_LSA: LSA crashes while initiating OCR on A0 controller(SCGCQ02043856 port of SCGCQ02000446)
 - MRSA: Crash when tried to flash corrupt firmware(SCGCQ02045015 port of SCGCQ02040739)
 - PH11 PA - LSA IT - Copyright info needs to be updated(SCGCQ02035247 port of SCGCQ02034466)
 - LSA Windows Readme: Update the LSA Windows Read me with the enhanced Silent installation instructions(SCGCQ02053863 port of SCGCQ02035322)
 - Fixed: WG: Instance validation for Controller Get fails(SCGCQ02070858 port of SCGCQ02070840)
 - LSA - Set PR properties input values need to be changed for "max PD option for PR concurrently"(SCGCQ02084533 port of SCGCQ02035322)
 - Fixed: Calculation to get possible range for RLM(SCGCQ02093538 port of SCGCQ02070841)
 - WG: snapdump downloaded after host triggered snapdump is not in zip file format(SCGCQ02089526 port of SCGCQ02084515)
 - Fixed: Calculation to get possible range for RLM(SCGCQ02093240 port of SCGCQ02070841)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102571 port of SCGCQ02102427)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02103244 port of SCGCQ02102427)
 - IP/Hostname discovery is not working through manual discovery for Windows and Linux(SCGCQ02102497 port of SCGCQ02102427)
 - WG 7.10: LSA crashes when generate snapdump or dowload snap dump operations are performed on direct agent(SCGCQ02099466 port of SCGCQ02094537)
 
EnhancementRequest:
 -Update candidate drive list for VD creation when UNMAP/FDE etc Exist.(SCGCQ01879211)
 -Aero None-Mode implementation.(SCGCQ01871350)
 -Add CTRL_SB_SOFT_SECURE_MODE event to indicate soft secure mode.(SCGCQ01965721)
 -LSA Client: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog.(SCGCQ02044922)
 -LSA Server: LDET Q32018 - RRB130 - Enable MR advanced debug dump to ttylog(SCGCQ02045048)
 -LSA Standalone - enhanced authentication/authorization (Windows).(SCGCQ01984624)
 - Increase in MR_PD_INFO.name length to 32 characters.(SCGCQ02079068)
 -Better error message for certain unmap operations.(SCGCQ02111563)
 - MR Windows IOCTL Error codes to Application added to MR API.(SCGCQ02103183)
 - API change to support NVMe Passthrough over OOB.(SCGCQ02035295)
 - API change to support new DCMD for consolidated device list.(SCGCQ02037158)
 - Customer needs to generate and extract the On-demand based debug data both for MR and iMR..(SCGCQ02000566)
 - Modification in MR_SNAPDUMP_TRIGGER_TYPE enum value.(SCGCQ02030653)
 - Reword event log messages as it creates unnecessary panic..(SCGCQ02013675)
 - Add New Generic OOB API To Read ROC Temp, Drive Temp, Drive Type, Drive Protocol and status through OOB BMC.(SCGCQ01940661)
 - Add a bit for atomic descriptor capable.(SCGCQ01965047)
 - Additional details about spare.(SCGCQ02033538)
 - API changes for Lane Margining.(SCGCQ01921241)
 - Introduced new controller bit.(SCGCQ01985474)
 - Add MFI STAT and MR Event for Secure Boot indicating fw dl was not allowed due to an existing pending key change.(SCGCQ02103973)
 - Driver parameter bit for support of tool box cmd.(SCGCQ02002119)
 - API change to support new DCMD for consolidated device list.(SCGCQ02016723)
 - .(SCGCQ01740789)
 
 
004.189.000.000 - Moderate Impact
---------------

 -(SCGCQ01351380) 
 - WG: Physical Drives tab should be aligned in center for Advanced Configuration.(SCGCQ01440777) 
 - Fixed: settings in configuration service API is inconsistent with other applciations(SCGCQ01518134) 
 - LSA WG Fury IT: Fury Device ID is showing as 00 instead of 0x0097 in controller properties logs.(SCGCQ01534444) 
 - SCGCQ01539326: [UNMAP]MR7.6 Unmap/WriteSame: AEN's are not generated when unmap capability gets disabled or enabled on a VD.(SCGCQ01539326) 
 - LSA Client 7.6: SPAN drives order is not maintained(SCGCQ01539355) 
 - Client: LSA should handle the not empty check for enclousre field for the physicalDevices response(SCGCQ01555968) 
 - IT-FURY-PH16:LSA-4.126.0.0-Fully Populated Enclosure S/N is "NA" and shown correctly after few drive removals.(SCGCQ01563352) 
 - SCGCQ01565134: IT-Ventura-PH7:LSA-4.126.0.0- FW update fails with error "File size Exceeds 16MB".(SCGCQ01565134) 
 - WG : Server detail is getting populated twice when user is using local IP (127.0.0.1(SCGCQ01565327) 
 - WG: During VD Creation on Simple Configuration, Clicking more than Once on the Finish Button is giving a Wrong Message.(SCGCQ01569262) 
 - WG: Copyright info is shown as 2017 instead of 2018(SCGCQ01571088) 
 - WG:Pop Up scroll missing in case there are more number of VDs to add while setting patrol read properties & Schedule CC(SCGCQ01571089) 
 - WG: User is notified to that multiselect PD/VD displays the properties but it is not supported(SCGCQ01571095) 
 - IT-FURY-PH16:LSA-SATA NCQ bit is always shown as disabled(SCGCQ01571261) 
 - LSA is not responding if online state is changed to offline(SCGCQ01571453) 
 - SCGCQ01571863: WG: LSA installation/uninstallation on linux does not notify the user on success or failure(SCGCQ01571863) 
 - Fixed: Windows OS details were reported as VMware details in Manual Search(SCGCQ01571874) 
 - WG: LSA wrapper indicates the progress of operations appears to be clickable while there is nothing user can select from list(SCGCQ01573087) 
 - SCGCQ01575706: WG:LSA installation exits on invalid option for selecting range of LSA events, it asks for retry with options listed again(SCGCQ01575706) 
 - SCGCQ01575999: FURY-PH16:LSA-Model Number is getting truncated for ST3000DM001,Hitachi HDS723020BLA642 models.(SCGCQ01575999) 
 - WG: the string 'status' is displayed multiple times after searching the server for manual addition(SCGCQ01577707) 
 - WG: LSA allows to replace HDD missing drive with SSD UG drive, fails with Partial Success.0 Successful;1 Failed notification(SCGCQ01577769) 
 - fixed: logout causing unexpected behavior during end cim connection for vmware systems(SCGCQ01578248) 
 - LSA Server: Removal of Additional Carriage Returns and Line feeds in tty log file(SCGCQ01579290) 
 - WG: Error message on a failed VD creation is displayed outside the allocated space(SCGCQ01586721) 
 - SCGCQ01588880:(SCGCQ01588880) 
 - LSA shows wrong diskgroup info when you have foreign PD(SCGCQ01590450) 
 - IPV6 IP is overlapping OS name and arch in LSA GUI if we see server discovery page in list view in SLES12 SP3(SCGCQ01595641) 
 - WG: LSA service crashes on trying to login with URI having incorrect mac address of the server(SCGCQ01601386) 
 -(SCGCQ01628332) 
 - fixed: Advanced Configuration is grayed out when there are 2 jbods available in the system.(SCGCQ01631267) 
 - Enclosure Location :Internal for back plane needs to be changed to "NONE" as part of new schema-24(SCGCQ01669558) 
 - LSA Schema 24: replace-missing get operation needs to follow the schema(SCGCQ01675460) 
 - Not able to set max no of PD using set patrol read properties in LSA/Storcli(SCGCQ01681070) 
 - WG: LSA 7.7 PA2 Not able to create RAID 00 VDs on iMR Ventura controller(SCGCQ01683638) 
 - When we try to modify the Unmap SCSI Unmap enabled feature via LSA it should give the reboot server message(SCGCQ01683938) 
 - During migration from r0(opal drives and non-secured) to r1, Add Pd list does not list the available drives (Greater/same si(SCGCQ01687072) 
 - WG: Issues pertaining to searching of the server : manual discovery in list view & GUI issues in the manual discovery panel(SCGCQ01687117) 
 - MR7.7_LSA: Unable to convert JBOD to UG when filesystem is present(SCGCQ01697980) 
 - LSA Linux doesn't have latest storelib(SCGCQ01713580) 
 - WG MR 7.7 PA2: LSA allows to add FDE and OPAL drives to create Encrypted volume(SCGCQ01721222) 
 - Server: LSA GUI Not Updating Security Key Info(SCGCQ01761801) 
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events(SCGCQ01761830) 
 - Fixed: nvme is allowed to mix with sas /sata(SCGCQ01762948) 
 - SCGCQ01763132: LSA: Alert Configuration response contains unsupported character(SCGCQ01763132) 
 - Foreign Config preview should show the VD details also(SCGCQ01788639) 
 - LSA Opal: RLM mixing for Opal SSC and Enterprise shouldn't be allowed when enableFDETypeMix=0(SCGCQ01790063) 
 - CC VD creation option is coming in LSA when the CC VD (SATA SSD) is in foreign config.(SCGCQ01817275) 
 - compilation error in server(SCGCQ01817434) 
 - Fixed: Auto Span Adjust with having >64 disks is not correct.(SCGCQ01827404) 
 - Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016(SCGCQ01841473) 
 - LSA Not allowing to clear/Import foreign configuration.(SCGCQ01849749) 
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01856350) 
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01874487) 
 - MR API - Incorrect value used for MR_DCMD_CTRL_SNAPDUMP_ONDEMAND(SCGCQ01882581) 
 - WG: LSA shows incorrect popups while making the drive from offline to online & vice versa(SCGCQ01922610) 
 - LSA - Not able to import other foreign configs if user have SED drive which is in foreign(SCGCQ01937406) 
 - In JBOD personality LSA service getting stopped when user change JBOD to UG(SCGCQ01971368) 
 -(SCGCQ01542415) 
 - LSA 7.6:In gateway LSA, none of the servers are listed except Self server in Remote server discovery page in Rhel 7.4(SCGCQ01552654) 
 - Correcting the library version display, ini file contents and also the readme files contents.(SCGCQ01561849) 
 - LSA: Warning Message needs to be changed when there is Controller firmware update failure(SCGCQ01564526) 
 - SWR: Device ID is not displayed in LSA.(SCGCQ01564621) 
 - MR/IR: Controller Device ID value mismatch in LSA(SCGCQ01564622) 
 - WG:LSA and web server port have references of SLIM and nignx in notification if invalid ports are given during LSA installatn(SCGCQ01571099) 
 - WG: Issues pertaining to replace drive confirmation popup(SCGCQ01573101) 
 - Security related information should not be displayed in IR/IT for LSA(SCGCQ01577891) 
 - LSA allows user to assgin a 512 B drive as replacement to 4k missing drive in a DG(SCGCQ01591175) 
 - SCGCQ01593058: Add non printable character support for sata pd product id display(SCGCQ01593058) 
 - Add a provision to indicate VMware/NonVmware server in Manual Discovery Panel(SCGCQ01600706) 
 - LSA WG FURY IT: UEFI image download is failing in LSA(SCGCQ01616545) 
 - LSA 7.6 Server: LSA is showing the option for PD:"Undo Prepare For Removal", when the DG is in TR state(SCGCQ01618243) 
 - Not able to create secure VD with latest MR 7.7 LSA 177.000.000-SCGCQ01664972 but OK with previous version(SCGCQ01665121) 
 - Error observed while adding Windows gateway server in through manual discovery(SCGCQ01675601) 
 - Secure Jbod unlock is not showing the proper error message in LSA(SCGCQ01677101) 
 - LSA MR7.7 PA2: Previously cleared configuration is seen in presence of OPAL foreign drive in Jbod Mode.(SCGCQ01685488) 
 - WG MR7.7 PA2:Once the 69639 error code is seen in LSA, performing every valid operation fails until manual refresh is perfo(SCGCQ01686013) 
 - WG MR 7.7:There is no import option for GHS Foreign device in LSA(SCGCQ01698105) 
 - Fixed: LSA handle count increase was observed(SCGCQ01713154) 
 - Add physical Drives page is not consistent across (Advanced Configuration and Modify drive Group(SCGCQ01716606) 
 - LSA: Handle Opal drive scenario for Hotspare and replace drive(SCGCQ01719043) 
 - LSA client: Add support to show incompatible profiles details(SCGCQ01727270) 
 - Add SCSI Unmap property at PD level(SCGCQ01732785) 
 - WG MR 7.7 Alpha:Foreign configuration pane does not show details for foreign dedicated hotspare drive.(SCGCQ01745770) 
 - WG:[intermittent] LSA page goes blank if we click on Drive tab and then immediately click on view serer profile(SCGCQ01747490) 
 - WG MR 7.7 alpha:Lsa does not update the PD(part of r0 volume) status once the PD is made online from offline.(SCGCQ01752969) 
 - [CISCO][TR]"Clear Transport Ready" option on rebuild LD should be removed or greyed out in LSA(SCGCQ01753229) 
 - MR LSA 7.7 : When user has flashed the controller FW for IT card, reboot system message is disappearing within few seconds(SCGCQ01761269) 
 - WG MR 7.7 al:LSA allows to create simple configuration in presence of Unconfigured bad drive and rest of the drives in jbod(SCGCQ01763742) 
 - MR7.7: Removal of UNMAP support for JBOD(SCGCQ01813078) 
 - Not able to create PRL11 CC VD (using 4 SATA SSD PD) from LSA webGUI.(SCGCQ01822209) 
 - fixed: LSA fails to create RAID 10 with large number of drives(SCGCQ01833469) 
 - LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online" .(SCGCQ01838943) 
 - WG: Software licensing agreement for linux RWC3 build is of Generic Channel(SCGCQ01886563) 
 - WG: LSA services crashes while adding the manually discovered VMware server to the manage server list(SCGCQ01918692) 
 -(SCGCQ01534450) 
 - LSA needs to change "Error code" : 86017, Description:Operation failed because of a resource reservation error" to proper mes(SCGCQ01556013) 
 - MR7.6_LSA: No Foriegn configuration details is shown in LSA(SCGCQ01581943) 
 - SCGCQ01582139: MR7.6_LSA: Enclosure ID and Device ID is shown blank in LSA event logs(SCGCQ01582139) 
 - WG: LSA Page auto scrolls down with scheduler wrapper going out of focus. LSA page would now be only half transparent(SCGCQ01586697) 
 - PH7 LSA WG Ventura: Sorting the drives on the basis of Device ID is not working fine(SCGCQ01587630) 
 - Fixed: Gateway crash when DA is logged in greater than max logins(SCGCQ01593855) 
 - WG: Instance validation failed for controller GET(SCGCQ01601458) 
 - WG: Minor text changes to be made in user information when no rows are selected in PD tab / DG tab / other hardware tab(SCGCQ01601656) 
 - [CISCO][TR] LSA fails to show DG in TR state after system reboot -storCLI OK(SCGCQ01615856) 
 - Enclosure Location :Internal for back plane needs to be changed to "NONE" as part of new schema-24(SCGCQ01638193) 
 - SCGCQ01680714: WG:Memory leak issues when the system is not idle ( Running the GUI suite when the memory leak test is in progress(SCGCQ01680714) 
 - LSA Wont display foreign data when enclosure information in not populated properly(SCGCQ01685449) 
 - WG MR 7.7:Invalid Temperature is displayed for OPAL drives.(SCGCQ01686024) 
 - Instant Secure Erase does not work in VMware when schedule is enabled(SCGCQ01686028) 
 - MR7.7_LSA: Error code:0 is observed when driver security is changed in LSA(SCGCQ01686050) 
 - LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode(SCGCQ01716622) 
 - fixed: max pd is a bigger number than the actual allowed max pd per raid level(SCGCQ01746200) 
 - WG MR 7.7 alpha: LSA displays wrong connector & path info for drives when enclosure is connected in wide port (x8 connection(SCGCQ01764794) 
 - WG: gateway system is not discovering systems with different web port number in remote discovery page.(SCGCQ01788630) 
 - LSA does not update the VD status when Migration is performed from r5(3drives)to r1(2drives)(SCGCQ01803743) 
 - LSA 502 Bad gateway is seen when Prepare for removal is performed on 5 drives at a time.(SCGCQ01809413) 
 - LSA : Stale entries are coming in DG tab when the VD (failed) is in foreign config.(SCGCQ01818953) 
 - fixed: Info "1920 more drives can be added" need to change in LSA(SCGCQ01827401) 
 - The display wrong location in page(SCGCQ01836732) 
 - SCGCQ01355833: WG:After deleting the cookies from browser, DA does not go back to login page.(SCGCQ01355833) 
 - WG: Changing the drive security key with invalid authentication key results in notification that is not in format(SCGCQ01573090) 
 - WG: Raid 00 DG having missing drives Span list dissapears when user tries to sort the drives based on capacity(SCGCQ01577833) 
 - MR 7.7: LSA did not allow to pick all SED/FDE but OK to pick one by one when create secure VD(SCGCQ01629062) 
 - SCGCQ01718994: LSA needs to convert "Error Code:69637. Descrption:Partial Success.0 Successful;1 Failed" into a readable message.(SCGCQ01718994) 
 - When there is pending personality, do not allow behavior Mode change, GUI refresh issue(SCGCQ01731312) 
 - Assign DHS is not showing any message in failure case(SCGCQ01732485) 
 - To enable the Alarm user has to click on the bottom of checkbox(SCGCQ01740783) 
 - LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap(SCGCQ01818960) 
 - LSA:fw error "BAIL_OUT at line 2909",FDE drive filtering for creating Encrypted RAID0 volumes lists non-FDE drives(SCGCQ01850008) 
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01876091) 
 - LSA needs to convert "Error Code:69637. Descrption:Partial Success.0 Successful;1 Failed" into a readable message.(SCGCQ01533554) 
 - WG: change Behavior Mode From JBOD to None is Not Working until closing the window(SCGCQ01635541) 
 - WG MR7.7PA2:In Jbod mode after first reboot and after converting Jbod to UG, advance configuraton leads to Jbod table.(SCGCQ01683001) 
 - MR 7.7 PA2: LSA does not refresh DG icon when PDs are made offline to online and visa versa.(SCGCQ01686029) 
 - WG MR 7.7 PA2:Encrypted Opal drive VD supports the Opal drive replacement with FDE drive(SCGCQ01697265) 
 - WG: JBOD conversion popup appears multiple times after converting all the drives to UG and clicking on Continue button(SCGCQ01737550) 
 - MR 7.7 alpha: LSA displays raid 1 as raid 1E when created using 4 drives.(SCGCQ01764771) 
 - SCGCQ01564386: IT-FURY-PH16:Drives are not listed under Enclosures ( "0" drives) under other Hardware if connected in Multipath.(SCGCQ01564386) 
 - Coverity Defect fix in 7.7 Stream(SCGCQ01682365) 
 - WG MR 7.7:Invalid Temperature is displayed for OPAL drives.(SCGCQ01714415) 
 - Client changes for defect SCGCQ01629703(SCGCQ01714659) 
 - MR7.7_LSA: After disabling PR, PR properties shows next scheduled time(SCGCQ01718119) 
 - LSA does not give expand option to perform OCE when one among 2vds is deleted under a DG(SCGCQ01803722) 
 - LSA is not locating all drives correctly(SCGCQ01924674) 
 - WG: LSA page doesnt show any notification on time consuming response operations,would lead to user redoing same again(SCGCQ01515496) 
 - WG: Email setting tab heading of LSA displays the entire sentence with "_" in between instead of space(SCGCQ01563343) 
 - Security Key Confirm Text box should not accept the copy of anything(SCGCQ01629574) 
 - Fixed: Show Advanced Config menu only if Unconfigured UG is present(SCGCQ01629703) 
 - WG: Readme shows wrong Version of LSA in html\files\LSA_ReadMe\LSA_Readme(SCGCQ01822525) 
 - SCGCQ01822561: WG: Changed LSA port is not listed after Direct agent installation on Rhel(SCGCQ01822561) 
 - Fixed: unblock LSA login on ESXi 6.7 U1(SCGCQ01866289) 
 - Linux system is getting IPV6 by default & it is not taking private IPV4 range(10 series) in LSA main page.(SCGCQ01817305) 
 - Making rebuild drive offline lsa gets 404.(SCGCQ01564627 port of SCGCQ01542412) 
 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade(SCGCQ01564633 port of SCGCQ01562368) 
 - LSA Crashes after clicking on foreign configuration(SCGCQ01564739 port of SCGCQ01545262) 
 - LSA WG Fury IT: Fury Device ID is showing as 00 instead of 0x0097 in controller properties logs.(SCGCQ01564943 port of SCGCQ01534444) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01565025 port of SCGCQ01504080) 
 - LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4(SCGCQ01565116 port of SCGCQ01555955) 
 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade(SCGCQ01566088 port of SCGCQ01562368) 
 - WG: No success or failure notification is shown on enabling the JBOD drive security(SCGCQ01566435 port of SCGCQ01511274) 
 - SCGCQ01545384: Installation of LSA with LWM option is showing installation_type = 0, in the LSA.conf file(SCGCQ01567110 port of SCGCQ01545384) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01569267 port of SCGCQ01504080) 
 - Making rebuild drive offline lsa gets 404.(SCGCQ01569465 port of SCGCQ01542412) 
 - Schema -23 is not upto date with the Mark/Replace Missing feature(SCGCQ01569474 port of SCGCQ01539349) 
 - LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n(SCGCQ01569949 port of SCGCQ01563340) 
 - LSA WG Inturder IT: 0 Byte drive is missing after sorting the drives based on capacity of drive.(SCGCQ01570203 port of SCGCQ01550970) 
 - Enclosure's physicaldevices URI getting failed with 405 error(SCGCQ01589492 port of SCGCQ01523122) 
 - Label of the user menu drop down should change reinforcing that selection worked.(SCGCQ01597876 port of SCGCQ01493942) 
 - LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n(SCGCQ01599402 port of SCGCQ01563340) 
 - Version changes for LSA 4.129 common project(SCGCQ01601148 port of SCGCQ01601146) 
 - WG:Once the Controller is moved from Raid to JBOD all the drives are counted as drive group(SCGCQ01601603 port of SCGCQ01598515) 
 - LSA: Warning Message needs to be changed when there is Controller firmware update failure(SCGCQ01604992 port of SCGCQ01564526) 
 - MR7.6_LSA: No Foriegn configuration details is shown in LSA(SCGCQ01605344 port of SCGCQ01581943) 
 - fixed: logout causing unexpected behavior during end cim connection for vmware systems(SCGCQ01609343 port of SCGCQ01578248) 
 - SCGCQ01355833: WG:After deleting the cookies from browser, DA does not go back to login page.(SCGCQ01614982 port of SCGCQ01355833) 
 - IPV6 IP is overlapping OS name and arch in LSA GUI if we see server discovery page in list view in SLES12 SP3(SCGCQ01616555 port of SCGCQ01595641) 
 - LSA displays "Erase operation is successful" when replace operation is in progress on the drive in same drive group.(SCGCQ01617930 port of SCGCQ01401460) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01628354 port of SCGCQ01504080) 
 - WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura(SCGCQ01634072 port of SCGCQ01473733) 
 - WG: few of the alert params have the missing controller ID tag for the events(SCGCQ01635756 port of SCGCQ01625923) 
 - LSAServer: Use scheduler call for heavy operations for performance improvement - PD Operations(SCGCQ01635765 port of SCGCQ01514283) 
 - WG: though the hotspare button will be disabled after adding VD for a Raid 1 DG, the hand cursor button appears(SCGCQ01635778 port of SCGCQ01626738) 
 -(SCGCQ01639457 port of SCGCQ01599526) 
 - MR7.6: LSA crashed with a mouse click on VD(SCGCQ01685343 port of SCGCQ01641760) 
 - Raid 1 Volume creation using 4 drives is displayed as Raid 1E(SCGCQ01686231 port of SCGCQ01686106) 
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config(SCGCQ01687172 port of SCGCQ01686080) 
 - When we try to modify the Unmap SCSI Unmap enabled feature via LSA it should give the reboot server message(SCGCQ01697468 port of SCGCQ01683941) 
 - LSA fails to flash GPMR2 package 50.1.0-1048 on top of MR 7.6 package 50.6.0-1255 on first try-it is successful on 2nd try(SCGCQ01697485 port of SCGCQ01680521) 
 - LSA not showing the proper time stamp in the schedule PR page(SCGCQ01698028 port of SCGCQ01677008) 
 - WG: LSA page doesnt show any notification on time consuming response operations,would lead to user redoing same again(SCGCQ01719179 port of SCGCQ01515496) 
 -(SCGCQ01733306 port of SCGCQ01721811) 
 - Fixed: LSA handle count increase was observed(SCGCQ01742153 port of SCGCQ01713154) 
 - Cannot use Special Characters in Domain Name for LSA Login(SCGCQ01747012 port of SCGCQ01745768) 
 - Server schema validation is failing(SCGCQ01764913 port of SCGCQ01619401) 
 - Enclosure Location :Internal for back plane needs to be changed to "NONE" as part of new schema-24(SCGCQ01764928 port of SCGCQ01638193) 
 - LSA installation failed on SLES15(SCGCQ01784699 port of SCGCQ01760620) 
 - LSA needs proper message for max config import(SCGCQ01789100 port of SCGCQ01763411) 
 - Cannot use Special Characters in Domain Name for LSA Login(SCGCQ01789161 port of SCGCQ01745768) 
 - WG: LSA allows user to replace a drive of a DG with drive on which drive clear is already in progress, GUI issues in popup(SCGCQ01810649 port of SCGCQ01803341) 
 - MR7.7: Removal of UNMAP support for JBOD(SCGCQ01813086 port of SCGCQ01813078) 
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config(SCGCQ01816649 port of SCGCQ01686080) 
 - C480-M5: LSA downloaded event log needs better decoding(SCGCQ01828830 port of SCGCQ01321211) 
 - LSA-4.1 : Array details are shown in LSA for the partial foreign config .(SCGCQ01850405 port of SCGCQ01818828) 
 - Tape drive state is blank when connected with 9400-8E card from LSA drives tab(SCGCQ01851980 port of SCGCQ01851906) 
 - LSA Not allowing to clear/Import foreign configuration.(SCGCQ01860933 port of SCGCQ01849749) 
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01880125 port of SCGCQ01874487) 
 - LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap(SCGCQ01897266 port of SCGCQ01818960) 
 - LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online" .(SCGCQ01898344 port of SCGCQ01838943) 
 - fixed: LSA fails to create RAID 10 with large number of drives(SCGCQ01901767 port of SCGCQ01833469) 
 - Fixed: unblock LSA login on ESXi 6.7 U1(SCGCQ01901774 port of SCGCQ01866289) 
 - OPAL drives fail to import when entering wrong security key then right security key after power cycle(SCGCQ01915861 port of SCGCQ01905192) 
 - [CISCO]LSA shows previously set security key (M3g@raid(SCGCQ01921581 port of SCGCQ01878346) 
 - LSA fails to start initialization on EPD if it has DDF(SCGCQ01921583 port of SCGCQ01849522) 
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01921592 port of SCGCQ01829895) 
 -(SCGCQ01921684 port of SCGCQ01841361) 
 - MR7.8 Foreign import from 7.7 to 7.8 with unmap VD and non unmap DHS does not alert user with a critical message/event(SCGCQ01921836 port of SCGCQ01876230) 
 - WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura(SCGCQ01538488 port of SCGCQ01473733) 
 -(SCGCQ01564591 port of SCGCQ01515389) 
 - WG: System display uniformity is not there in GUI (Remote server discovery(SCGCQ01567177 port of SCGCQ01553588) 
 - Client: Handle Enable/Disable style for search Button(SCGCQ01567216 port of SCGCQ01539573) 
 - LSA Crashes after clicking on foreign configuration(SCGCQ01567307 port of SCGCQ01545262) 
 - Manual discovery of servers(SCGCQ01569264 port of SCGCQ01539471) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01569569 port of SCGCQ01504080) 
 - LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n(SCGCQ01570076 port of SCGCQ01563340) 
 - Converting the JBOD Pds to Unconfigured good PD during VD creation VD creation(SCGCQ01597581 port of SCGCQ01518204) 
 - Manual discovery of servers(SCGCQ01600837 port of SCGCQ01539471) 
 - LSA 7.6:In gateway LSA, none of the servers are listed except Self server in Remote server discovery page in Rhel 7.4(SCGCQ01615020 port of SCGCQ01552654) 
 - WG: LSA service crashes on trying to login with URI having incorrect mac address of the server(SCGCQ01615042 port of SCGCQ01601386) 
 -(SCGCQ01633836 port of SCGCQ01599526) 
 - Fixed: Gateway crash when DA is logged in greater than max logins(SCGCQ01635183 port of SCGCQ01593855) 
 - Use schedular call for heavy operations for performance imporvement(SCGCQ01635665 port of SCGCQ01506032) 
 - Allow individual element's properties download - VD / PD / DG / BBU / Server profile(SCGCQ01635761 port of SCGCQ01518113) 
 - JBOD Mode : WG: Even after clicking Convert JBOD the JBOD conversion page does not refresh with updated list(SCGCQ01635784 port of SCGCQ01617721) 
 - Cisco - CSCvi55512 - CC in concurrent mode runs only on 2 VDs at a time(SCGCQ01676612 port of SCGCQ01670094) 
 - Cisco - CSCvi55512 - CC in concurrent mode runs only on 2 VDs at a time(SCGCQ01676732 port of SCGCQ01670094) 
 -(SCGCQ01685548 port of SCGCQ01685009) 
 - LSA Wont display foreign data when enclosure information in not populated properly(SCGCQ01686054 port of SCGCQ01685449) 
 - LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config(SCGCQ01687173 port of SCGCQ01686105) 
 - fixed: WG: managing the manually added server fails : windows(gateway(SCGCQ01697195 port of SCGCQ01682360) 
 - LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode(SCGCQ01716641 port of SCGCQ01716622) 
 -(SCGCQ01718985 port of SCGCQ01698211) 
 - Security Key Confirm Text box should not accept the copy of anything(SCGCQ01788477 port of SCGCQ01629574) 
 - LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01880123 port of SCGCQ01876091) 
 - handling the session management(SCGCQ01892868 port of SCGCQ01829897) 
 - Change tools to report drives attached to HBAs as JBOD instead of UGOOD(SCGCQ01898263 port of SCGCQ01802344) 
 - Fixed: Auto Span Adjust with having >64 disks is not correct.(SCGCQ01901754 port of SCGCQ01827404) 
 - LSA 7.8:LSA provides Instant secure erase option for Locked UG BAD drives.(SCGCQ01904075 port of SCGCQ01893304) 
 - LSA 7.8: Unable to launch LSA from different web server port after LSA upgrade.(SCGCQ01904345 port of SCGCQ01901758) 
 -(SCGCQ01920699 port of SCGCQ01808698) 
 - LSA: Ventura B0: BIOS Flashing Failure Observed in EFI Storcli and Multiple Tries Causes UART Unresponsive(SCGCQ01921839 port of SCGCQ01829669) 
 - SCGCQ01803373: WG: LSA service crashes on downloading support logs in case of Linux 64 bit OS(SCGCQ01921842 port of SCGCQ01803373) 
 - WG: LSA does not notify user on OS VD present if multiple VDs are selected and with non OS VD is selected first(SCGCQ01928961 port of SCGCQ01926674) 
 - LSA Server: Populate the Drive Sector Size while reading the LD MFI command(SCGCQ01930623 port of SCGCQ01926876) 
 - Schema -23 is not upto date with the Mark/Replace Missing feature(SCGCQ01557738 port of SCGCQ01539349) 
 - LSA WG Inturder IT: 0 Byte drive is missing after sorting the drives based on capacity of drive.(SCGCQ01564629 port of SCGCQ01550970) 
 - SCGCQ01547992: WG: standalone LSA Installation on Rhel 6.9 32 bit notifies user with invalid message(SCGCQ01564682 port of SCGCQ01547992) 
 - I/Os are not recover after drives pull for DHSP to rebuild.(SCGCQ01569579 port of SCGCQ01514206) 
 - Support from LSA back-end to allow JBODs to be converted to UG for advance VD creation(SCGCQ01597602 port of SCGCQ01519271) 
 - WG:On changing behavior from None to JBOD and moving to Controller Console page, LSA page redirects to Personality management(SCGCQ01670841 port of SCGCQ01629821) 
 - [CISCO][TR] LSA fails to show DG in TR state after system reboot -storCLI OK(SCGCQ01676281 port of SCGCQ01615856) 
 - Server schema validation is failing(SCGCQ01676389 port of SCGCQ01619401) 
 - WG: Email setting tab heading of LSA displays the entire sentence with "_" in between instead of space(SCGCQ01679003 port of SCGCQ01563343) 
 - Secure Jbod unlock is not showing the proper error message in LSA(SCGCQ01680728 port of SCGCQ01677101) 
 - LSA taking more time to discover VMWare servers(SCGCQ01681092 port of SCGCQ01681069) 
 -(SCGCQ01697478 port of SCGCQ01685009) 
 - LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode(SCGCQ01716625 port of SCGCQ01716622) 
 -(SCGCQ01718980 port of SCGCQ01698211) 
 -(SCGCQ01749087 port of SCGCQ01698211) 
 - Modify Properties option is enabled for VDs which are part of Transport Ready Drive Group(SCGCQ01764894 port of SCGCQ01763056) 
 - Fixed: Delay in updating drive count in LSA due to slowness in asynchronous events(SCGCQ01826237 port of SCGCQ01761830) 
 - The LSA is failing to take into account current USED PDs from another configured VD during next VD creation(SCGCQ01837378 port of SCGCQ01833791) 
 - SCGCQ01841280: Before importing foreign CC VD, model number of SSD is not coming in LSA(SCGCQ01851919 port of SCGCQ01841280) 
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01856730 port of SCGCQ01856350) 
 - WG: VMware server takes too long to discover in remote discovery page : nearly 20 minutes(SCGCQ01891168 port of SCGCQ01889547) 
 - CC VD creation option is coming in LSA when the CC VD (SATA SSD(SCGCQ01897144 port of SCGCQ01817275) 
 - Update the Windows Server 2019 OS name in LSA(SCGCQ01897178 port of SCGCQ01866322) 
 -(SCGCQ01920924 port of SCGCQ01818618) 
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01921819 port of SCGCQ01856350) 
 - LSA 7.6 Client: Cosmetic replace drive selection issue(SCGCQ01566455 port of SCGCQ01539347) 
 - SCGCQ01539326: [UNMAP]MR7.6 Unmap/WriteSame: AEN's are not generated when unmap capability gets disabled or enabled on a VD.(SCGCQ01567176 port of SCGCQ01539326) 
 - WG: Alignment in Remote Server Discovery page changes when it is in List view and filtered with any one of the OS type.(SCGCQ01567193 port of SCGCQ01471834) 
 - SCGCQ01538253: LSA-4.055.0.0: IT-Cutlass- LSA Event logs is missing Enclosure ID's and slot-36 is shown to be present in(SCGCQ01569137 port of SCGCQ01538253) 
 - SCGCQ01538253: LSA-4.055.0.0: IT-Cutlass- LSA Event logs is missing Enclosure ID's and slot-36 is shown to be present in(SCGCQ01569138 port of SCGCQ01538253) 
 - LSA WG Fury IT: Controller type is showing as IR for IT card(SCGCQ01569488 port of SCGCQ01540821) 
 - Client:Allow individual element's properties download - VD / PD / DG / BBU / Server profile(SCGCQ01597592 port of SCGCQ01518206) 
 - WG:Once the Controller is moved from Raid to JBOD all the drives are counted as drive group(SCGCQ01601608 port of SCGCQ01598515) 
 - WG: empty details for policy change displayed in events "Previous = Current Write Policy: Now = Current Write Policy:"(SCGCQ01635759 port of SCGCQ01625912) 
 - WG:On changing behavior from None to JBOD and moving to Controller Console page, LSA page redirects to Personality management(SCGCQ01635779 port of SCGCQ01629821) 
 - TR VD should be excluded from the PR VD list(SCGCQ01677110 port of SCGCQ01677062) 
 - Implemented: Allow mixing of nvme drives to be mixed with SATA/SAS drives(SCGCQ01697042 port of SCGCQ01697026) 
 - Hercules : Snap 4 : Alpha : LSA provides option of performing an RLM operation on Degraded VD, which fails(SCGCQ01789156 port of SCGCQ01731931) 
 - MR7.6: LSA crashed with a mouse click on VD(SCGCQ01816428 port of SCGCQ01641760) 
 - Handling the set text mechanism in client(SCGCQ01886532 port of SCGCQ01850387) 
 - Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016(SCGCQ01897181 port of SCGCQ01841473) 
 - WG: LSA provides option of Secure using FDE if non encrypted r1 VD with secure drive is assigned with DHSP,(SCGCQ01915812 port of SCGCQ01906914) 
 - LSA 7.8:Import option is given for the Incomplete foreign VD(SCGCQ01921678 port of SCGCQ01865420) 
 - LSA is allowing to delete OS VD.(SCGCQ01921689 port of SCGCQ01873420) 
 - SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon(SCGCQ01921919 port of SCGCQ01856350) 
 - WG: VMware server takes too long to discover in remote discovery page : nearly 20 minutes(SCGCQ01961510 port of SCGCQ01889547) 
 - Not able to set max no of PD using set patrol read properties in LSA/Storcli(SCGCQ01697480 port of SCGCQ01681070) 
 - Add Virtual Drive option is available for DGs with Transport Ready feature set(SCGCQ01764885 port of SCGCQ01763052) 
 - SCGCQ01538253: LSA-4.055.0.0: IT-Cutlass- LSA Event logs is missing Enclosure ID's and slot-36 is shown to be present in(SCGCQ01828400 port of SCGCQ01538253) 
 - Fixed: Crash when pressing back button after logout(SCGCQ01892905 port of SCGCQ01865309) 
 - Remove un printable characters from LSA log(SCGCQ01901769 port of SCGCQ01901760) 
 - LSA does not show Secure Erase option for foreign secured JBOD drive-CLI works(SCGCQ01920701 port of SCGCQ01916249) 
 - WG: LSA allows to remove the data drive during the RLM from single drive R0 and allows migrate to R0 with no drives(SCGCQ01921580 port of SCGCQ01823858) 
 - Modify the LSA Health Algorithm to consider the Blocked VD(SCGCQ01565119 port of SCGCQ01504080) 
 - LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4(SCGCQ01569761 port of SCGCQ01555955) 
 - Unable to import foreign secured VDs with different security key(SCGCQ01731357 port of SCGCQ01670139) 
 - Activity to check-in Auto-BST files to 7.8 streams(SCGCQ01794950 port of SCGCQ01793057) 
 - Activity to check-in Auto-BST files to 7.8 streams(SCGCQ01817915 port of SCGCQ01793057) 
 - SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01869566 port of SCGCQ01829895) 
 - Server: LSA GUI Not Updating Security Key Info(SCGCQ01897099 port of SCGCQ01761801) 
 - LSA WG Fury IT: Controller type is showing as IR for IT card(SCGCQ01564631 port of SCGCQ01540821) 
 - LSA Schema 24: replace-missing get operation needs to follow the schema(SCGCQ01679329 port of SCGCQ01675460) 
 - LSA shows wrong diskgroup info when you have foreign PD(SCGCQ01698150 port of SCGCQ01590450) 
 - LSA needs proper message for max config import(SCGCQ01813925 port of SCGCQ01764977) 
 - UG LSA 7.8 PA2:Incomplete foreign VD is seen when Clear foreign config is performed.(SCGCQ01851155 port of SCGCQ01849681) 
 - Fixed: Advance configuration operation should be greyed out if max pds are already configured(SCGCQ01922015 port of SCGCQ01850445) 
 - I/Os are not recover after drives pull for DHSP to rebuild.(SCGCQ01564737 port of SCGCQ01514206) 
	
EnhancementRequests:
 - Add "Replace Missing Drive" feature to LSA(SCGCQ01399204) 
 - Part 2 of 2: Support TCG Opal 2.0 via SafeStore for VDs and SystemPD (Legacy JBOD) in RAID Mode and JBOD/SDS Modes(SCGCQ01599762) 
 -(SCGCQ01740789) 
 - Added customer serial number field to MFC Manufacturing 2 structure(SCGCQ01873417) 
 - MR API changes to support EKMS over OOB(SCGCQ01874035) 
 - Add new error code for tampered or invalid controller(SCGCQ01885686) 
 - Interrupt coalsecing setting per group of 8 replies queues (h/w VF registers(SCGCQ01886424) 
 - [MR 7.8] API change to export "disable least latency mode"(SCGCQ01887495) 
 - HDET: Support smp passthrough storeliboob (API changes requirement(SCGCQ01916035) 
 - Add secure boot key update complete event(SCGCQ01928254) 
 - Add Board Support Package Image Type to MR_IMAGE_TYPE(SCGCQ01931637) 
 - Support dynamically add/remove controller in Storelib IT for MCTP over PCIe(SCGCQ01934815) 
 - Fix MR_CTRL_INFO to support backward compatibility(SCGCQ01946548) 
 - Add "Replace Missing Drive" feature to LSA(SCGCQ01399205) 
 - Manually add server details to the list of servers(SCGCQ01539514) 
 - Switch attached NVMe HW RAID support for Supermicro backplanes(SCGCQ01740787) 
 - LSA displays "Erase operation is successful" when replace operation is in progress on the drive in same drive group.(SCGCQ01401460) 
 - UNMAP/TRIM/WRITESAME for NVMe devices for R0/EPD/JBOD(SCGCQ01746609) 
 - Manual discovery of servers(SCGCQ01539471) 
 - Change tools to report drives attached to HBAs as JBOD instead of UGOOD(SCGCQ01802344) 
 -(SCGCQ01599763) 
 - UNMAP/TRIM/WRITESAME for NVMe devices for R0/EPD/JBOD(SCGCQ01746608) 


004.069.000.000  - Moderate Impact
---------------

Defects (20)
-.(SCGCQ01753405)
- Server: LSA GUI Not Updating Security Key Info.(SCGCQ01761801)
- CC VD creation option is coming in LSA when the CC VD (SATA SSD) is in foreign config.(SCGCQ01817275)
- Fixed: Auto Span Adjust with having >64 disks is not correct.(SCGCQ01827404)
- Lenovo 18D - missing display "Uninstall LSA" shortcut in the "Start Menu" under windows2016.(SCGCQ01841473)
- LSA Not allowing to clear/Import foreign configuration.(SCGCQ01849749)
- SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon.(SCGCQ01856350)
- LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01874487)
- seg fault is seen when when we try to generate CRC errors using megamon.(SCGCQ01841619)
- Not able to create PRL11 CC VD (using 4 SATA SSD PD) from LSA webGUI.(SCGCQ01822209)
- fixed: LSA fails to create RAID 10 with large number of drives.(SCGCQ01833469)
- LSA does not ask for user confirmation for possible Data corruption while changing Pd state from "offline->online".(SCGCQ01838943)
- LSA : Stale entries are coming in DG tab when the VD (failed) is in foreign config.(SCGCQ01818953)
- fixed: Info "1920 more drives can be added" need to change in LSA.(SCGCQ01827401)
- The display wrong location in page(SCGCQ01836732)
- LSA : GUI tab alignment is not coming proper after user initiates manual learn cycle for Supercap.(SCGCQ01818960)
- LSA:fw error "BAIL_OUT at line 2909",FDE drive filtering for creating Encrypted RAID0 volumes lists non-FDE drives.(SCGCQ01850008)
- LSA login to ESXi 6.x servers fails in SLES 15 OS.(SCGCQ01876091)
- Fixed: unblock LSA login on ESXi 6.7 U1.(SCGCQ01866289)
- Linux system is getting IPV6 by default & it is not taking private IPV4 range(10 series) in LSA main page.(SCGCQ01817305)
- Security Key Confirm Text box should not accept the copy of anything.(SCGCQ01788477 port of SCGCQ01629574)
- SCGCQ01856350: LSA_18D installed in SLES15 OS, the icon in LSA shows as Redhat icon.(SCGCQ01856730 port of SCGCQ01856350)
- The LSA is failing to take into account current USED PDs from another configured VD during next VD creation.(SCGCQ01837378 port of SCGCQ01833791)
- SCGCQ01538253: LSA-4.055.0.0: IT-Cutlass- LSA Event logs is missing Enclosure ID's and slot-36 is shown to be present in.(SCGCQ01828400 port of SCGCQ01538253)
- Activity to check-in Auto-BST files to 7.8 streams.(SCGCQ01817915 port of SCGCQ01793057)
- SCGCQ01829895: LSA uninstaltion is not working in SLES15 OS.(SCGCQ01869566 port of SCGCQ01829895)

EnhancementRequests (20)
- RTTrace API Changes.(SCGCQ01745568)
- API Changes for Driver/FW DCMD HandShake.(SCGCQ01841266)
- RTTrace Enable/Disable API changes.(SCGCQ01830211)
- Criteo: API changes reversal.(SCGCQ01760512)
- Mixing Rules for SED and non-SED drives to create non-secure array with controller security enabled.(SCGCQ01757538)
- Unmap: Define new API for enhanced UNMAP support.(SCGCQ01758062)
- Adding API bit to indicate whether forced personality change is supported or not.(SCGCQ01762153)
- Unmap: Define new events for enhanced UNMAP support [MR7.8].(SCGCQ01803319)
- Deprecate the snap dump fields that are no longer needed for MR_SNAP_DUMP_PROPERTIES structure.(SCGCQ01816724)
-.(SCGCQ01818580)
- Add the API to clear all the snap-dumps from firmware.(SCGCQ01824135)
- API change to provide learn complete timestamp.(SCGCQ01845269)
- Added Support for Triggering SnapDump.(SCGCQ01848759)
- Add secure boot support.(SCGCQ01792416)
- Including The Time Stamp for every Snap Dump created in the firmware.(SCGCQ01797424)
- Aero FW - Reporting SSD wear gauge values for OEM specific customers.(SCGCQ01798686)
- [MR 7.8] API change to return apt failure status for a personality change request.(SCGCQ01853480)
- Added new events for unmap policy changes.(SCGCQ01871912)
- API Changes - After Vision PSOC FW update, applications should ask the user for power cycle instead of reboot.(SCGCQ01765150)
- Change tools to report drives attached to HBAs as JBOD instead of UGOOD.(SCGCQ01802344)


004.062.000.000  - Moderate Impact
--------------
fixed:
Nginx versions since 0.5.6 up to and including 1.13.2 are vulnerable to integer overflow vulnerability in nginx range filter module resulting into leak of potentially sensitive information triggered by specially crafted request.https://nvd.nist.gov/nvd.cfm?cvename=CVE-2017-7529.

Defects (109)
- LSA server report for iMR Inv controller displays dedicatedHotSparePerDriveGroup is 0 under "maxLimit".(SCGCQ01375788)
- SCGCQ01393056: Enclosure ID is coming up as null in LSA.(SCGCQ01393056)
- WG: Error message not fitting inside the message box in "Enable Drive Security" page..(SCGCQ01442477)
- WG: Issues pertaining to 'Make JBOD Secure' Pop up.(SCGCQ01446801)
- PerfImp: Don't handle SLIM_EVT_EXCEEDS_MAX if there is no event requires complete refresh.(SCGCQ01447165)
- WG: UI Pattern in "Virtual Drive Settings" is not uniform while creating and modifying VD properties..(SCGCQ01447697)
- WG: "Change" button shown as disabled when user tries to change Behavior mode..(SCGCQ01450713)
- DG count is shown incorrectly in server summary page : VMware 6.5.(SCGCQ01451571)
- WG: success message box for "change personality" does not have proper border.(SCGCQ01453980)
- WG: Event Log table headers needs space - Cosmetic.(SCGCQ01460053)
- WG: Notification after saving the changes in "Manage Power Save Settings" needs cosmetic change..(SCGCQ01460078)
- Requested personality field is not updated for Ventura.(SCGCQ01465642)
- API performance Issues pertaining to LSA Build 004.005.000.000( VMware esxi 6.5 ): Raid Mode with JBOD drives.(SCGCQ01467754)
- WG: Tooltip for help link in "Remote Server Discovery" page is not displayed..(SCGCQ01471842)
- WG: "Available UG drives" form is shown blank when "Type" is selected from ALL to any other drives..(SCGCQ01472186)
- WG: LSA showing inappropriate message after securing a DG using FDE security..(SCGCQ01472201)
- Buttons are inconsistent in Email Settings page of LSA.(SCGCQ01472752)
- Fixed: LSA app UI cannot be opened when connect M.2 NVME SSD(via HSBP) to LSI 9460-16i/9440-8i.().(SCGCQ01474461)
- MR 7.3.1_LSA fails to find server when there is no network.(SCGCQ01482320)
- During Advanced Vd Creation PD selection order is not maintained by the client.(SCGCQ01498969)
- Display the ROC temperature in Fahrenheit as well along with Celsius.(SCGCQ01504619)
- WG: Hand mouse pointer is used in " Background Process progress " window , where it shows the name of background operations..(SCGCQ01505999)
- [lenovo 18A] [Bugzila 117507] -Reopen -The LSA doesn’t work in Suse12.3, which has many NICs.(SCGCQ01506045)
- WG: Caps letter is expected in Settings for Alert settings successful and restore default value successful message..(SCGCQ01509253)
- WG: Sorting of drives by model number does not work for JBOD drives.(SCGCQ01511247)
- Do not allow the user to manage Personality Panel if set personalty is not supported.(SCGCQ01514527)
- SCGCQ01515443: WG: Typo in Event ID: 114 of PD state Change event related to sheild state.(SCGCQ01515443)
- 502 bad gate way observed on enclosure cable push/pull.(SCGCQ01524150)
- WG : LSA allows to add VD on offline DriveGroup and operation fails anyways.(SCGCQ01526342)
- MR 7.5_LSA: LSA gives wrong message after Online FW Update on Ventura IMR controller.(SCGCQ01532725)
- LSA shows wrong diskgroup info when you have foreign PD.(SCGCQ01590450)
- Lenovo_18B: Not able to set max no of PD using set patrol read properties in LSA/Storcli.(SCGCQ01681070)
- Fixed: LSA handle count increase was observed.(SCGCQ01713154)
- Lenovo CIT 18B: LSA Linux doesn't have latest storelib.(SCGCQ01713580)
- SCGCQ01385340: Health is not coming proper after foreign config import..(SCGCQ01385340)
- Disabled Phy is not populated from the server when we fire /phys uri.(SCGCQ01389892)
- MR7.3_Focused Regression_Strange character when exceeding max number of Uncof good drives on iMR.(SCGCQ01419325)
- WG: Not all space in "Foreign Configuration" tab is clickable..(SCGCQ01467702)
- WG: Font style across the "Advanced Configuration" form should be made same..(SCGCQ01472063)
- Removing dead code from LSA7.5 stream..(SCGCQ01472185)
- WG: "Ok" button needs to be in caps in "Mixed listed drives" confirmation page and one more cosmetic change..(SCGCQ01472190)
- WG: There is no alignment for the error message while user changes the personality mode when PR is in progress..(SCGCQ01474932)
- WG: LSA is not allowing User to change No of PD's allowed for Patrol Read in Set PR properties through KeyBoard..(SCGCQ01479402)
- WG: Trying to clear configuration does not show any warning in server summary page regarding cached data, in CC page it shows.(SCGCQ01486698)
- WG: Select all check box is still selected even if one of the drive group is unselected while assigning HSP to existing DG.(SCGCQ01488141)
- WG: while creating FDE VD, type by default is selected as "All" in PD selection pane, unable to select all FDE drives.(SCGCQ01488169)
- Requested personality field is not updated for Ventura.(SCGCQ01494598)
- temperature change in controller is not refeclected in LSA..(SCGCQ01500344)
- Set patrol read window shows a time in past..(SCGCQ01503810)
-.(SCGCQ01508528)
- SCGCQ01509259: WG: Separator is missing in few places of event logs..(SCGCQ01509259)
- WG: LSA provides option of performing an RLM operation on Degraded VD, which fails.(SCGCQ01509708)
- LSA Server: Set Patrol read is not shown when the volume is created with SSD.(SCGCQ01511260)
- SCGCQ01513209: WG: Simple configuration tab show invalid options before the raid level drop down list the supported raid levels.(SCGCQ01513209)
- WG : Advanced configuration tab gets disabled after secure erasing the FDE foreign drives.(SCGCQ01514728)
- SCGCQ01521013: MR 7.5_LSA: LSA gives wrong message after Online FW Update on Ventura IMR controller.(SCGCQ01521013)
- MR 7.5_LSA: LSA keeps on refreshing during the background operations- Full init, RLM, CC etc.(SCGCQ01522807)
- WG: Behavior mode is missing in "personality management" window..(SCGCQ01523045)
- SCGCQ01525738: MR 7.5_LSA: Wrong nginx version is reported in linux ( SLES and RHEL ) Operating Systems..(SCGCQ01525738)
- Instance validation issues with LSA build 4.55 with IR3 controller.(SCGCQ01528425)
-.(SCGCQ01628332)
- WG: Current Profile is not selected by default in the table that lists the available profiles for the controller..(SCGCQ01442481)
- WG: "%" is accepted along with the input for Expand VD value - But not accepted for all..(SCGCQ01445384)
- WG: Partition line is required in Controller Properties Page..(SCGCQ01445396)
- WG: Status icon of physical drive is not changed after changing the state of the PD from rebuild to offline..(SCGCQ01461144)
- WG:LSA doesn't allow to secure more than one DG using FDE..(SCGCQ01472853)
- SCGCQ01474327: Handle dynamic length serial number as part of serial number VPD page 0x80.(SCGCQ01474327)
- WG: GUI : Cosmetic issues in clear configuration notificationp.(SCGCQ01486692)
- WG: LSA does not notify the user with notification on starting the VD initialization.(SCGCQ01487270)
- WG: able to add VD for scheduling consistency check even after all the VD's have been deselected.(SCGCQ01489509)
- WG:Add physical Drive button is clickable before VD list is loaded while scheduling CC or PR, no notification to user to wait.(SCGCQ01489885)
- LSA provides option of performing an RLM operation on Degraded VD, which fails.(SCGCQ01489942)
- LSA: Virtual drive, spare and drivegroup is not supported for IT but seen in URI response for Physical drives..(SCGCQ01500099)
- WG: Selection of different drive type is activated after few clicks.(SCGCQ01503786)
- RWC3 launch tab is showing the LSI Storage Authority.(SCGCQ01503896)
- WG : Pop up for securing FDE drive has inconsistency in text.(SCGCQ01507972)
- In settings window "Restore Default Alert settings" button is not saving the default values.(SCGCQ01508002)
- WG: Confirm Check box is not aligned with the "Enable Security" button.(SCGCQ01511250)
- LSA WG: arrow mark in the link " <- Go back to Drive Group, Drives and Other Hardware list" is not clickable.(SCGCQ01511390)
- WG:Server Logs does not contain status of energy pack it mentions "Requested element not found in the stack.":error "69634".(SCGCQ01512318)
- WG: Spell Check issues with "message_en.js" used for displaying the GUI notification.(SCGCQ01512377)
- Sorting of Event logs wrt View Events and Download Logs.(SCGCQ01512750)
- WG: LSA add physical Disks pane shows empty drive list even if there are 182 drives for adding for RLM operation.(SCGCQ01513656)
- Controller operations schema instant validation is failed.(SCGCQ01514528)
- WG: LSA shows the message "The virtual disk has not been initialized" even when 32 VD's have been selecte.(SCGCQ01521694)
- Lenovo-18B: IPV6 IP is overlapping OS name and arch in LSA GUI if we see server discovery page in list view in SLES12 SP3.(SCGCQ01595641)
- WG: "Virtual Drive expanded successfully" message is still shown even after the page refresh post VD expansion..(SCGCQ01445693)
- WG: Cosmetic changes required in tooltip messages of Configure options in Controller Actions..(SCGCQ01447797)
- WG: Space is required between RAID and it's type in Available UG drives form and one more cosmetic change..(SCGCQ01472194)
- WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura.(SCGCQ01473733)
- LSA: partial VD hide operation is failing..(SCGCQ01484118)
- SCGCQ01506090: WG: In Settings under email tab , email id list will always have an empty row once we add and remove email_id.(SCGCQ01506090)
- WG:Launching LSA using ip:2463 in browser, User can see the HOME page flash before redirecting to Remote discovery.(SCGCQ01439795)
- WG: LSA displays empty box instead of "Action Successful" for "Prepare for removal" and "Undo prepare for removal".(SCGCQ01447823)
- WG: "Adding the virtual drive will add the corresponding virtual drives for PR" is not shown when "select all" box is used..(SCGCQ01461133)
- WG: Size of "Back" & "Save" buttons are not same once the user saves the changes after scheduling CC.(SCGCQ01472749)
- WG: Hand symbol is not seen for close button while Adding drive during reconstruction of a DG.(SCGCQ01473748)
- Disabling the add PD button.(SCGCQ01488036)
- WG: no notification shown on assigning dedicated hotspare to existing DG.(SCGCQ01488155)
- System x PE: LSA Does Not Support the Hyphen Character "-" In Domain Names.(SCGCQ01507989)
- WG: Infinite request observed on stopping LSA and Nginx services..(SCGCQ01509681)
- WG: Error message on a failed operation of RLM in displayed outside the allocated space.(SCGCQ01515263)
- WG: arrow mark in the link " <- Go back to Drive Group, Drives and Other Hardware list" is not clickable.(SCGCQ01442471)
- WG: Expand windows is showing the capacity in decimal value with too many integers after decimal point..(SCGCQ01445686)
- Address Code review defects for ER SCGCQ01416373.(SCGCQ01455923)
- WG: Ambiguous "Success" message needs to be changed for disabling drive security.(SCGCQ01461177)
- Cannot import foreign configuration from LSA.(SCGCQ01524354)
- WG: Email setting tab heading of LSA displays the entire sentence with "_" in between instead of space.(SCGCQ01563343)
- SCGCQ01599526: Lenovo PE: Memory Leak in LSABug.(SCGCQ01599526)

EnhancementRequests (20)
- New configuration params added for EPD-PT devices.(SCGCQ01599607)
- API changes needed to support eHBA product series.(SCGCQ01727346)
- Create sanitize events.(SCGCQ01713708)
- Modify event string APIs for MISSING and OFFLINE LDs.(SCGCQ01628177)
-.(SCGCQ01404233)
- SCSI UNMAP switching support from LSA GUI.(SCGCQ01461207)
- NVDATA parameter to OPAL SED.(SCGCQ01614689)
- Add new MFI Status to block requested operation due to existing controller configuration.(SCGCQ01670135)
- Change the mr.h API comment showing the new return status for the - MR_DCMD_PD_GET_INFO.(SCGCQ01670234)
- API change for Switch attached NVMe HW RAID support for Supermicro backplanes.(SCGCQ01697667)
- LSA: Make heavy operation by wrapping scheduler call.(SCGCQ01416373)
 - LSA Server: PR:SCGCQ01231749 -- Show controller temperature in LSA for RAID and SAS IT controllers.(SCGCQ01443721)
- LSA Server: PR:SCGCQ01231749 -- Show controller temperature in LSA for RAID and SAS IT controllers.(SCGCQ01443731)
- Support drive Select ALL functionality in LSA GUI PD Operations and Mixing of drives during vd creation.(SCGCQ01454110)
- SCGCQ01454353: Retrieve and process the ESXi events in a single shot.(SCGCQ01454353)
-.(SCGCQ01454367)
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01563340)
- We will be removing the confirmation popup from all the actions as we got here from multiple forms like this pop up is annoying.(SCGCQ01447015)
- Support drive Select ALL functionality in LSA GUI VD/DG Operations.(SCGCQ01453114)
-.(SCGCQ01472631)

CSETActivities (87)
- In Standalone LSA periodic automatic refresh is not happening. To display the latest status do manual refresh.(SCGCQ01411631 port of SCGCQ01397546)
- MR7.3_Focused Regression_Strange character when exceeding max number of Uncof good drives on iMR.(SCGCQ01420224 port of SCGCQ01419325)
- LSA service is not working in Linux.(SCGCQ01443712 port of SCGCQ01442733)
- WG: Event Log table headers needs space - Cosmetic..(SCGCQ01464556 port of SCGCQ01460053)
- SCGCQ01424621: PD serial number getting truncated on few PDs.(SCGCQ01466763 port of SCGCQ01424621)
- MR 7.3.1_LSA fails to find server when there is no network.(SCGCQ01500133 port of SCGCQ01482320)
- Updated PD firmware version is not reflecting even after LSA refresh..(SCGCQ01501204 port of SCGCQ01382013)
- Cisco_Plumus_LR :Proper spacing should be there in between Event and History in view event logs "EventHistory not generated"..(SCGCQ01502201 port of SCGCQ01385344)
- While retrieving the enclosure details instead of referring to the ENCL structure, in this case LSA is referring the PD structure.(SCGCQ01503907 port of SCGCQ01315392)
because of which the issue.(SCGCQ01503926 port of SCGCQ01288032)
- fixed: clear drive should not be candidate drive for create configuration.(SCGCQ01503958 port of SCGCQ01196088)
- Fixed: Span order is in reverse compare to other apps.(SCGCQ01504234 port of SCGCQ01330269)
- LSA shows max pd for Raid 1 without checking support of Raid 1E.(SCGCQ01514472 port of SCGCQ01513338)
- Cisco - CSCvg96681 - LSA-3.163 should display proper message after logout.(SCGCQ01531154 port of SCGCQ01521114)
- Making rebuild drive offline lsa gets 404..(SCGCQ01564627 port of SCGCQ01542412)
- LSA Crashes after clicking on foreign configuration.(SCGCQ01564739 port of SCGCQ01545262)
- Modify the LSA Health Algorithm to consider the Blocked VD.(SCGCQ01565025 port of SCGCQ01504080)
- LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4.(SCGCQ01565116 port of SCGCQ01555955)
- Cisco - CSCvh55470 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade.(SCGCQ01566052 port of SCGCQ01562368)
- SWR: Device ID is not displayed in LSA..(SCGCQ01566241 port of SCGCQ01564621 )
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01599402 port of SCGCQ01563340)
- MR7.6_LSA: No Foriegn configuration details is shown in LSA.(SCGCQ01605344 port of SCGCQ01581943)
- fixed: logout causing unexpected behavior during end cim connection for vmware systems.(SCGCQ01609343 port of SCGCQ01578248)
- SCGCQ01355833: WG:After deleting the cookies from browser, DA does not go back to login page..(SCGCQ01614982 port of SCGCQ01355833)
- LSA displays "Erase operation is successful" when replace operation is in progress on the drive in same drive group..(SCGCQ01617930 port of SCGCQ01401460)
- SCGCQ01506090: WG: In Settings under email tab , email id list will always have an empty row once we add and remove email_id.(SCGCQ01620406 port of SCGCQ01506090)
- WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura.(SCGCQ01634072 port of SCGCQ01473733)
- Raid 1 Volume creation using 4 drives is displayed as Raid 1E.(SCGCQ01686231 port of SCGCQ01686106)
- Cannot use Special Characters in Domain Name for LSA Login.(SCGCQ01747012 port of SCGCQ01745768)
- LSA: patrol reads gets initiated on all the vd's that are created though only one vd is selected..(SCGCQ01448948 port of SCGCQ01442107)
- DG count is shown incorrectly in server summary page : VMware 6.5.(SCGCQ01460039 port of SCGCQ01451571)
- WG: LSA takes some time (2-3 min) in order to display the remote server page after multiple service restarts..(SCGCQ01465657 port of SCGCQ00903348)
- DG count is shown incorrectly in server summary page : VMware 6.5.(SCGCQ01466743 port of SCGCQ01451571)
- LSA server giving null for enclosure serial number.(SCGCQ01466744 port of )
- Address Code review defects for ER SCGCQ01416373.( port of SCGCQ01445713)
- MR 7.3.1_LSA fails to find server when there is no network.(SCGCQ01484107 port of SCGCQ01482320)
- Added fwflash status as part of controller health status.(SCGCQ01503830 port of SCGCQ01375153)
- While retrieving the enclosure details instead of referring to the ENCL structure, in this case LSA is referring the PD structure because of which the issue.(SCGCQ01503955 port of SCGCQ01288032)
- [lenovo 18A] [Bugzila 117507] -Reopen -The LSA doesn’t work in Suse12.3, which has many NICs.(SCGCQ01514258 port of SCGCQ01506045)
- System x PE: LSA Does Not Support the Hyphen Character "-" In Domain Names.(SCGCQ01514469 port of SCGCQ01507989)
- Allows raid 1e input even if RAID 1E is not supported by fw.(SCGCQ01514756 port of SCGCQ01513331)
- Activity to check-in build files.(SCGCQ01514879 port of SCGCQ01514834)
-.(SCGCQ01520055 port of SCGCQ01508528)
- Cisco - CSCvh55470 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade.(SCGCQ01564633 port of SCGCQ01562368)
- Activity to check-in AutoBST files to new MR 7.5 streams.(SCGCQ01564703 port of SCGCQ01564674)
- WG: LSA service crashes on trying to login with URI having incorrect mac address of the server.(SCGCQ01615042 port of SCGCQ01601386)
- MR7.6: LSA crashed with a mouse click on VD.(SCGCQ01685343 port of SCGCQ01641760)
-.(SCGCQ01685548 port of SCGCQ01685009)
- LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config.(SCGCQ01687173 port of SCGCQ01686105)
- LSA is not showing the proper message when user unlocks the foreign jbod drivesin JBOD mode.(SCGCQ01716641 port of SCGCQ01716622)
- SDS/HBA progress issues.(SCGCQ01460070 port of SCGCQ01052983)
- Physical drives Get call taking considerably long time :it takes 5+ minutes to respond for 24 PD's in an enclosure.(SCGCQ01460084 port of SCGCQ01435908)
- SCSI UNMAP switching support from LSA GUI.(SCGCQ01461211 port of SCGCQ01461207)
- C480-M5: LSA downloaded event log needs better decoding.(SCGCQ01501225 port of SCGCQ01321211)
- Cisco - CSCve68492 - Storage Logs display a blank event when a secure PD is unlocked.(SCGCQ01503902 port of SCGCQ01359128)
- SCGCQ01509259: WG: Separator is missing in few places of event logs..(SCGCQ01514773 port of SCGCQ01509259)
- WG: Infinite request observed on stopping LSA and Nginx services..(SCGCQ01526363 port of SCGCQ01509681)
- SCGCQ01547992: WG: standalone LSA Installation on Rhel 6.9 32 bit notifies user with invalid message.(SCGCQ01564682 port of SCGCQ01547992)
- LSA: Warning Message needs to be changed when there is Controller firmware update failure.(SCGCQ01604992 port of SCGCQ01564526)
- SCGCQ01599526: Lenovo PE: Memory Leak in LSA.(SCGCQ01633836 port of SCGCQ01599526)
- Secure Jbod unlock is not showing the proper error message in LSA.(SCGCQ01680728 port of SCGCQ01677101)
- LSA detects secured JBODs as unconfigure good when drives moved to another system -StorCLI detects them as foreign config.(SCGCQ01687172 port of SCGCQ01686080)
- Cisco - CSCvi84075 - LSA, CTRL-R and HII doesn't display the foreign config when MAX VDs are present.(SCGCQ01718980 port of SCGCQ01698211)
- LSA is not Displaying Both the Foreign Configurations (Encrypted and Unencrypted) for Import/Clear/re scan..(SCGCQ01460090 port of SCGCQ01460076)
- WG: LSA is not Displaying Both the Foreign Configurations (Encrypted and Unencrypted) for Import/Clear/re scan..(SCGCQ01460400 port of SCGCQ01448976)
- Fixed: LSA app UI cannot be opened when connect M.2 NVME SSD(via HSBP) to LSI 9460-16i/9440-8i.(SCGCQ01481410 port of SCGCQ01474461)
- LSA build script automation for VBAS environment.(SCGCQ01497385 port of SCGCQ01385344)
- Activity to check-in version files in common.(SCGCQ01520315 port of SCGCQ01512599)
- Cisco - CSCvg96681 - LSA-3.163 should display proper message after logout.(SCGCQ01531153 port of SCGCQ01521114)
- MR/IR: Controller Device ID value mismatch in LSA.(SCGCQ01566055 port of SCGCQ01564622)
- LSA Client 7.6: SPAN drives order is not maintained.(SCGCQ01614833 port of SCGCQ01539355)
- Hercules- LSA : VD access policy not showing as blocked for SVD on CC VD offline..(SCGCQ01443689 port of SCGCQ01442554)
- LSA: During the installation "Range of Events" selection is not reflecting in the LSA.conf file.(SCGCQ01472166 port of SCGCQ01472048)
- SCGCQ01479375: LSA WebGui: "logs.txt" is generated in logs directory after fresh installation in Linux..(SCGCQ01480902 port of SCGCQ01479375)
- LSA WG Fury IT: Fury Device ID is showing as 00 instead of 0x0097 in controller properties logs..(SCGCQ01564943 port of SCGCQ01534444)
- Modify the LSA Health Algorithm to consider the Blocked VD.(SCGCQ01565119 port of SCGCQ01504080)
- Cisco - CSCvi55512 - CC in concurrent mode runs only on 2 VDs at a time.(SCGCQ01676612 port of SCGCQ01670094)
- LSA Wont display foreign data when enclosure information in not populated properly.(SCGCQ01686054 port of SCGCQ01685449)
- LSA : Silent installation is accepting the invalid options also for LSA/HPE/RWC3.(SCGCQ01472265 port of SCGCQ01389392)
-.(SCGCQ01564591 port of SCGCQ01515389)
- API performance Issues pertaining to LSA Build 004.002.000.000( VMware esxi 6.5 ).(SCGCQ01460393 port of SCGCQ01436886)
- LSA Windows BST Automation scripts.(SCGCQ01472059 port of SCGCQ01460401)
- LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4.(SCGCQ01557665 port of SCGCQ01555955)
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01564577 port of SCGCQ01563340)
- LSA WG Inturder IT: 0 Byte drive is missing after sorting the drives based on capacity of drive..(SCGCQ01564629 port of SCGCQ01550970)
- LSA WG Fury IT: Controller type is showing as IR for IT card.(SCGCQ01564631 port of SCGCQ01540821)
- I/Os are not recover after drives pull for DHSP to rebuild..(SCGCQ01564737 port of SCGCQ01514206)

4.011.000.000 - Moderate Impact
-------------
Defects (234)
- SDS/HBA progress issues.(SCGCQ01052983)
- Fixed: Added relevant null pointer checks.(SCGCQ01319978)
- Selected firmware version is coming empty for IR/IT/IMR controller.(SCGCQ01321474)
- Start PatrolRead success dialog box needs change in alignment.(SCGCQ01324866)
- WG: Trying to import Encrypted VD with Drive security disabled results in error code: 0x11005, it provides No Details to user.(SCGCQ01325783)
- Link speed is not displaying any details in LSA.(SCGCQ01326129)
- Defect to check in code review defects.(SCGCQ01329391)
- Client js file changes for 7.3.(SCGCQ01331593)
- On Successful Firmware flash client displays improper Icon Message.(SCGCQ01332708)
- Control panel of LSA Help & support link still has reference to LSI. should be changed to broacom.(SCGCQ01337321)
- LSA asks for user permission to navigate away on clicking home button after creating simple configuration.(SCGCQ01338009)
- WG: GUI Issues pertaining to FW flash ER implementation SCGCQ01273627: Request to improve message displayed during FW Update.(SCGCQ01342542)
- IR Card global hot spare assignment is not refreshing the page.(SCGCQ01345357)
- Cisco_HSW_Validation_LSA: LSA accepting decimal values for "Set Adjustable Task Rate" which is saved as round value.(SCGCQ01345553)
- LSA 7.3 Client Coverity fix.(SCGCQ01347309)
- Cisco_LSA: 'vdname' parameter is missing in the event description that is generated whenever a volume property is modified.(SCGCQ01350435)
- WG:descripancies in update firmware page after selecting load bios option.(SCGCQ01350865)
- SCGCQ01350908: WG:Temperature of Unconfigured Drive is displayed as 0C under More properties.(SCGCQ01350908)
- WG:LSA displays Redhat icon in remote discovery page ,though SUSE is installed in system.(SCGCQ01351455)
- LSA taking the max VD size value when the user presses ENTER after specifying the VD size.(SCGCQ01356216)
- SCGCQ01356217: WG: LSA Service crashes on trying the PD details of the simple config created.(SCGCQ01356217)
- LSA_MR_7.3_Alpha: Save option can be grayed out or disabled after user saves the changes for schedule CC.(SCGCQ01357152)
- LSA_MR_7.3_Alpha: LSA doesn't display consistent Foreign Configuration information to the user.(SCGCQ01358048)
- WG: Incorrect notification shown after selecting 32 virtual drives.(SCGCQ01358095)
- SCGCQ01358097: LSA_MR_7.3_Alpha: Space optimization between the size value & size unit is needed in foreign configuration page.(SCGCQ01358097)
- LSA_MR_7.3_Alpha: User cannot select "Advanced Configuration" by clicking on the description below it in Server landing page.(SCGCQ01358122)
- LSA_MR_7.3_Alpha: Space Alignment for better presentation needed in Server Profile Page.(SCGCQ01358148)
- LSA_MR_7.3_Alpha: Percentage value for the Background Operations is not seen if browser is zoomed.(SCGCQ01358261)
- LSA crash when service starts with empty LSA.conf file.(SCGCQ01358264)
- SCGCQ01358892: Buttons "Try Updating Again" is not highlighted when user attempts to flash the firmware after any failure.(SCGCQ01358892)
- SCGCQ01358947: WG: Invalid text Content displayed on selecting multiple Virtual drives/Physical Drives.(SCGCQ01358947)
- WG: "Select Personality" dropdown lists the current personality first by default.(SCGCQ01359030)
- WG: Clickable "hand icon' is not displayed when we move cursor over Bus dev text of controller in Server summary page.(SCGCQ01359034)
- SCGCQ01372670: When User tries to click on Update FW Button, LSA asks for Navigation Confirmation without displaying Update FW page for IT.(SCGCQ01372670)
- "Add CacheCade-SSD VD" tab getting greyed out after deleting created vd,even if physical drive is selected under "Add SSD pd".(SCGCQ01372722)
- WG: VD creation fails when multiple VD's are created with 1MB size.(SCGCQ01373500)
- "Finish" button in Modify drive group work even if its grayed out.(SCGCQ01374945)
- WG: Issues pertaining to Controller Diagnostic logs.(SCGCQ01375839)
- WG: GUI Issues pertaining to Instant secure erase of an FDE Drive.(SCGCQ01375858)
- There is a mismatch about Backplane (Enclosure) "Product ID" and "Enclosure Model" in LSA.(SCGCQ01376005)
- Spare URI does not respond on iMR Invader.(SCGCQ01376605)
- WG: After physically removing the PD from the R10 DG, the DG Span tab does not load.(SCGCQ01376781)
- "Since Log Clear" does not create the last event "Log Clear" in Var/log/messages.(SCGCQ01376849)
- WG: LSA does not list the Drive Group Tab , on creation of 240 VD (15 DG, 16 VD in each of DG) and reinstalling the LSA.(SCGCQ01378585)
- WG: Windows Application Event viewer lists 31 events instead of 30, after installing LSA with the option "Since Last reboot".(SCGCQ01378669)
- WG: LSA does not automatically refresh on hiding an Degraded DG.(SCGCQ01378693)
- Client: Error message that user encounters for Max User login, message needs to be displayed with proper message.(SCGCQ01378778)
- Client: WG: Instance Validation failed for Spares GET URI : MR Ventura.(SCGCQ01378782)
- WG: unable to start VD initialization on 32 VD's when there are 240 VD created & Foreign configuration present in system.(SCGCQ01378808)
-.(SCGCQ01378812)
- WG: Error message is not proper if the username is not provided while verifying server in Manager server page.(SCGCQ01379795)
- WG:In premium features Safe ID & Serial Number needs to be highlited for better understanding.(SCGCQ01379818)
- WG: Close button can be given with a "hand" symbol in Compare and select form like all close button in other form has.(SCGCQ01380587)
- WG: Available Unconfigured drives is not formatted properly for display.(SCGCQ01380591)
- WG: Domain Authentication is shown as Default in "MAnage Server Page".(SCGCQ01380642)
- Size increment button is not working while modifying a VD that is created in MB size.(SCGCQ01380830)
- WG: "Advanced and Simple Configuration" is enabled when UG drives are "prepared for removal" and no other drives are left.(SCGCQ01380977)
- SCGCQ01383828: LSA service crashes while trying to access the IR3 controller.(SCGCQ01383828)
- WG:VD properties were not well partitioned for CacheCade - SSD config , compare to normal VD creation in HDD.(SCGCQ01384561)
- WG: Few enhancements needed in VD Expand form.(SCGCQ01389165)
- SCGCQ01389195: WG: Naming convention for VD can be made consistent for the VD's created through Advanced and Simple configuration.(SCGCQ01389195)
- Enter key is functioning as a backspace in "Set Adjustable Task Rate" - Can be disabled.(SCGCQ01389203)
- LSA mail server settings does not allow to enter name of smtp server.(SCGCQ01389204)
- WG: No. of VD's available to create is not shown properly for spanned vd's when span depth is modified.(SCGCQ01389421)
- Storcli: Battery Capacitance is displayed incorrectly across different applications.(SCGCQ01392000)
- WG: More Actions for drive is not working after staring and stopping Clear operation under Drives tab.(SCGCQ01392056)
- WG: User has to click twice on the table header to change the sorting order for any table in LSA.(SCGCQ01393336)
- Copyright link is taking to top of the page rather taking to Broadcom website.(SCGCQ01393706)
- WG: PD state info is not updated properly in the Drives tab after PD's are converted from online to offline.(SCGCQ01393771)
- WG: "Clear" and "Rescan" buttons could be highlighted for the better look in Foreign Configuration Tab.(SCGCQ01394954)
- "Add Virtual Drives" is grayed out for specific VD sizes after user presses "tab-alt" keys.(SCGCQ01398966)
- WG: Verify and Sign In Buttons are overlapping in list view in Manage Server Page.(SCGCQ01399610)
- LSA is not showing "Activate..." button for Premium Features when it is navigated after "Update Firmware" page.(SCGCQ01399670)
- WG:LSA sending email alert notifications to user which doesn't exist.(SCGCQ01418580)
- Drives under both Physical drives and Span drives tab are allowed to select simultaneously.(SCGCQ01428129)
- Login to VMware is taking at time more than 30 seconds.(SCGCQ01429431)
- Physical drives Get call taking considerably long time :it takes 5+ minutes to respond for 24 PD's in an enclosure.(SCGCQ01435908)
- WG:while editing a created VD, user cannot increase the VD size in MB .Only can decrease the size.(SCGCQ01438268)
- WG:LSA is not sorting properly the drives with different capacity of units i.e TB and GB.(SCGCQ01439751)
- WG: View server profile does not contain info on the Device id, which is sorted according to device id itself.(SCGCQ01440773)
- WG: operation of Combining JBOD drives with & without files system to move to Unconfigurued good is partially successful.(SCGCQ01440778)
- WG: Space required between two strings in the description of "Enable Drive Security".(SCGCQ01442479)
- WG: LSA Displays "Error Code:1:An user is already Logged in with Different Credentials" even user is using same credentials.(SCGCQ01442773)
- WG: LSA is changing to latest login user account though it is already logged with different User Account in different Tab.(SCGCQ01442774)
- WG: No. of UG drives are improperly updated in the Drives header tab when replace operation is triggered on a physical drive.(SCGCQ01444724)
- WG: No. Of Power Supplies info displayed is overlapping on the enclosure details. Need proper display alignment.(SCGCQ01444794)
- LSA showing 'binaryPath:./LSA' during service start in Linux.(SCGCQ01445709)
- LSA server giving null for enclosure serial number.(SCGCQ01445713)
- WG: LSA events displays invalid details for unexpected sense events.(SCGCQ01445719)
- WG: Description for event Code"579" is '0" in LSA event logs.(SCGCQ01446803)
- WG:"Disable Data Protection" is not updating in LSA until user do a manual refresh.(SCGCQ01447843)
- SCGCQ01448707: WG: LSA Event logs has enquiry info for Vendor, model and serial numbers appended with $ symbols.(SCGCQ01448707)
- WG: Inconsistency seen w.r.t making drive online while RLM is in progress.(SCGCQ01449722)
- WG: Event log page is navigating to change personality when the behavior mode is set from other tab of the same browser.(SCGCQ01450719)
- DG count is shown incorrectly in server summary page : VMware 6.5.(SCGCQ01451571)
- WG:Controller health status not updated on moving JBOD drive from offline --> online, personality : JBOD.()
- LSA Server: Handling of additional events in Cache module.(SCGCQ01451573)
- LSA: During the installation "Range of Events" selection is not reflecting in the LSA.conf file.(SCGCQ01464514)
- [lenovo 18A] [Bugzila 117507] -Reopen -The LSA doesn’t work in Suse12.3, which has many NICs.(SCGCQ01506045)
- WG: Enclosure ID is shown "Unknown" for NVMe JBOD only in event logs, Profile id=11.(SCGCQ01291162)
- WG: LSA page does not refresh on starting Full initialization on 240 VD.(SCGCQ01292183)
- Phase3 Beta PCIe: Loading SLOOB fails with error message "ExitLib failed for SAS IT Controller!! rval 0x801A".(SCGCQ01292964)
- 7.3 Client : Coverity defects check-in.(SCGCQ01308624)
- SCGCQ01309034: Coverity defect fixes check-in.(SCGCQ01309034)
- Fixed: Code maintainability issue.(SCGCQ01318344)
- coverity defect fies for : Suspicious use of non-short-circuit boolean operaton.(SCGCQ01320079)
- In Simple Config, if user select a VD and select the check box of "Assign HSP", VD size is getting changed to different size.(SCGCQ01321225)
- WG: LSA notifies user that VD will be deleted after VD erase even if the option was not selected.(SCGCQ01325795)
- WG: user notification appearing after user starts/stops the initialization on multiple VD's needs to be updated.(SCGCQ01326134)
- LSA doesn't show FW component name while FW flash operation.(SCGCQ01337028)
- WG: Multiple options of RLM are selected together for radio button used to select one of the 3 RLM operations.(SCGCQ01342615)
- LSA does not display "Link Speed" for phy 8 properly for iMR Ventura.(SCGCQ01355929)
- When the CC is scheduled as "Continuously", it is not reflected in UI after saving the changes.(SCGCQ01357007)
- Warning message has to be corrected in Foreign configuration page and one more hyperlink issue.(SCGCQ01358066)
- LSA is not taking "dot(.)" from num pad , but taking "dot(.)" form keypad while specifying the vd capacity.(SCGCQ01358908)
- Selected firmware version is coming empty for IR/IT/IMR controller.(SCGCQ01364736)
- WG: LSA displays the notification "This operation can be performed only on 32 drives at a time" 32 times.(SCGCQ01373067)
- WG: Global hotspare & Dedicated hotspare are displayed as plural entities for every hotspare listed in physical drive tab.(SCGCQ01375707)
- WG: Instance Validation failed for Spares GET URI : MR Ventura.(SCGCQ01375778)
- fixed: Min & Max of "PdRaidLevel_1E" under the "pdsForRaidLevels" is populated even though it is not supported in iMR.(SCGCQ01375817)
- WG: Other hardware tab lists wrong count of list of hardware connected when enclosure connected in multipath.(SCGCQ01376109)
- WG: View server profile contents exceed the border limits of the LSA page.(SCGCQ01378556)
- SCGCQ01378774: WG: Information of the virtual drive info and PD's involved in DG vanishes on removing & inserting the PD back from a DG.(SCGCQ01378774)
- WG: Links present in Backplane properties are so light that they look like grayed out. Needs enhancement.(SCGCQ01380680)
- WG: User is allowed to click on "Next" button even if page is not completely updated during the VD creation & RLM operations.(SCGCQ01381734)
- GUI Issues found in Advanced Configuration page.(SCGCQ01381764)
- Firmware flash message should have "new" removed from string.(SCGCQ01382062)
- LSA getting logged in , even if the password is wrong.(SCGCQ01388957)
- "%" is allowed for entering no. of seconds for locating the drives.(SCGCQ01389182)
- WG: Size limit warning is thrown if the user is giving valid size using spinner button while modifying VD.(SCGCQ01389340)
- WG: Message displayed after flashing the controller FW has to be modified for better presentation - Enhancement.(SCGCQ01389483)
- Spinner Button for increase and decrease size is not working when the size is 1.09 TB.(SCGCQ01392053)
- WG: "Username" has to be grayed out when user start typing in the login page of "Manage Server Page".(SCGCQ01393764)
- WG: UG Drives count is not updated properly after modifying a DG.(SCGCQ01393774)
- Phase 5 IT LSA - EFI-BSD version is not displayed fully when Version length is more than 12 characters.(SCGCQ01394914)
- Mismatch in enclosure properties between LSA and storecli utility.(SCGCQ01395021)
- WG: "Managing SAS Storage Link Speed" opens up on clicking help topic of "Manage PCIe Storage Interface".(SCGCQ01395075)
- when clicking on more actions for any UG drives to make DHS,the options remains as it is in LSA though the operation is done.(SCGCQ01403884)
- WG: Like "Flash Firmware" button in "Update Firmware" page, "Update" button should also have hand symbol & one more issue.(SCGCQ01405822)
- WG: while expanding exiting VD, the expand VD page is not consistent.(SCGCQ01416379)
- Fixed: WG: LSA conf does not contain the perf mode settings options configurable.(SCGCQ01422214)
- WG: Clicking on "Benefits of each MegaRAID Advanced Software Option" in premium feature is not taking to proper link.(SCGCQ01428156)
-.(SCGCQ01428383)
- LSA doesn't allow creating spanned Raid levels with 2 spans using more than 32 drives.(SCGCQ01435647)
- API performance Issues pertaining to LSA Build 004.002.000.000( VMware esxi 6.5 ).(SCGCQ01436886)
- WG : "Replace Drive "window needs improvement to look uniform.(SCGCQ01439805)
- when flashing FW with 16 mb/32 mb.ROM file , LSA throws inappropriate message.(SCGCQ01440772)
- WG: LSA displays the property Drive Security Capable as 'No' even when security is supported.(SCGCQ01442209)
- WG: the controller operations Query param : 4 has 'premium feature' and 'pinned cache' URI's GET calls in response.(SCGCQ01443879)
- WG: Confirmation Message has to be changed when more than one drives are converted from JBOD to UG state.(SCGCQ01444672)
- SCGCQ01445818: MR 7.4_Alpha_LSA does not find a server in RHEL 7.4.(SCGCQ01445818)
- WG: LSA times out after "Clear Configuration" command is issued when there is a OFFLINE DG present.(SCGCQ01447788)
- WG: Size for the VD is not updated properly when edited during VD creation.(SCGCQ01447791)
- WG: An extra "." needs to be removed in the event description for "Initialization complete on VD".(SCGCQ01449783)
- WG:Instance Validation Fails for foreignConfiguration-schema.json in iMR_Ventura.(SCGCQ01473733)
- WG: Raid 50 Vd Creation fails on unselecting drives after changing span during VD creation.(SCGCQ01309542)
- Coverity Defects - Performance Inefficiencies.(SCGCQ01313878)
- Fixed: Coverity: Class hierarchy inconsistencies.(SCGCQ01318333)
- Client: Coverty defect fixes check-in.(SCGCQ01318336)
- VD size getting increased while creating VD using simple config - Regression.(SCGCQ01341947)
- WG: Once the FW update is completed LSA shows junk character in the notification about firmware flash was successful.(SCGCQ01342536)
- SCGCQ01348082: LSA: Loopback occurs during launch. (intermittent issue).(SCGCQ01348082)
- Expand page is not closed when opened for second time.(SCGCQ01357224)
- "Add Virtual Drives" is disabled when user changes from invalid size to valid size through increment button.(SCGCQ01358299)
- WG: Error message that user encounters for Max User login, message needs to be displayed with proper message.(SCGCQ01375255)
- "Server Profile" displays blank back plane info for ctrl-1.(SCGCQ01375992)
- LSA Client : Foreign Configuration Panel issues with locked and unlocked foreign drives.(SCGCQ01378050)
- DG Actions menu is not shown properly after zooming in when VD's are hidden.(SCGCQ01380663)
- WG: Size range warning is not shown while modifying VD when unit is selected from MB to GB.(SCGCQ01380818)
- LSA Evevnt: Access policy for HIDDEN/Transport is coming as Empty.(SCGCQ01380828)
- LSA Server: User is provided with Hide and Un-Hide option though there is no HIDE performed on a VD.(SCGCQ01380845)
- WG: LSA service crashes on hiding and unhiding DG's with dedicated hotspare.(SCGCQ01380912)
- SCGCQ01383765: Resolve linux server compilation issues.(SCGCQ01383765)
- WG: Reconstruction progress is not refreshed even after the VD is cleared on which reconstruction was happening.(SCGCQ01383800)
- LSA : Silent installation is accepting the invalid options also for LSA/HPE/RWC3.(SCGCQ01389392)
- WG: Clicking on View server profile just before controller console page loads results in blank page.(SCGCQ01396731)
- WG: "DG degraded notification" is not auto-refreshed after Raid5 VD is brought from offline to online.(SCGCQ01398964)
- WG: When LSA is configured with NAT server, it is shown twice in the Remote Discovery Page.(SCGCQ01401484)
- WG: LSA is displaying loop-back address in remote discovery page while accessing LSA with IPV6 address.(SCGCQ01401546)
- WG: Hidden links present in premium features page.(SCGCQ01412883)
- WG:VD properties details need some changes to look uniform across the application.(SCGCQ01418574)
- WG: Help link for Premium Features is opening in dual tabs.(SCGCQ01428169)
- LSA: patrol reads gets initiated on all the vd's that are created though only one vd is selected.(SCGCQ01442107)
- WG:LSA is not showing the options "Pause Patrol Read|Abort Patrol Read" when PR background operation is running.(SCGCQ01442350)
- WG:when user is closing the message box for "Clear Configuration",the "X" symbol is not shown with hand symbol.(SCGCQ01442356)
- LSA service is not working in Linux.(SCGCQ01442733)
- WG: Invalid text"Each_Frehole" present in Pop up of Adding VD to existing Drive group.(SCGCQ01446454)
- WG: "Add Hot Spare" Button is enabled after selecting and deselecting the drives.(SCGCQ01448882)
- WG: LSA is not Displaying Both the Foreign Configurations (Encrypted and Unencrypted) for Import/Clear/re scan.(SCGCQ01448976)
- WG: Event with ID 552 is not updated properly. Information on Mode is empty.(SCGCQ01450725)
- LSA Client: SDS/HBA progress issue.(SCGCQ01459948)
- System x PE: LSA Does Not Support the Hyphen Character "-" In Domain Names.(SCGCQ01507989)
- LSA not giving the Un Hide All Virtual Drives operation when DG contain Hidden and normal VDs.(SCGCQ01308440)
- Coverity Defects fixes for Stream LSA7.3.(SCGCQ01311864)
- LSA7.3: Coverity defect fixes in Server code.(SCGCQ01316168)
- Coverity: Integer handling issues.(SCGCQ01318418)
- LSA Client : IR/IT Multiple Options are allowed in Update Firmware Screen.(SCGCQ01343645)
- Add hot spare page cosmetic issues.(SCGCQ01358219)
- WG:Change button is active even if button appears inactive for "Change personality", fails with an inappropriate notification.(SCGCQ01358967)
- FW last modified time is not coming properly while FW upload.(SCGCQ01359056)
- WG:while editing created vd for CacheCade - SSD Caching Configuration,the write policy tab is coming down.(SCGCQ01380641)
- WG: In "Advanced Configuration" page, Raid settings and Drive Attributes are not numbered properly.(SCGCQ01380646)
- WG: Issues pertaining to "Server is taking long to respond" LSA page.(SCGCQ01383122)
- SCGCQ01395189: WG: "Manage PCIe Storage Interface" displays empty table for MR Ventura controller with profile id 13.(SCGCQ01395189)
- WG: LSA is displaying loop-back address in remote discovery page while accessing LSA with IPV6 address.(SCGCQ01415223)
- WG: Question mark missing in "Erase" confirmation form.(SCGCQ01415923)
- WG: Extra "." (dot) has to be removed in VD Initialization confirmation message and one more cosmetic issue.(SCGCQ01428137)
- WG: Instance Validation is failing for driveGroupConfigurationService-schema.json in MR_Ventura card.(SCGCQ01443739)
- MR7.4_Alpha_LSA crashed when trying to download firmware RHEL 7.4.(SCGCQ01447240)
- LSA Client Refresh issue while making more than one drive(s) offline when RLM is in progress.(SCGCQ01449870)
- WG: No success /failure Notification is shown in server summary page on making a offline drive online.(SCGCQ01451575)
- WG:2 Spans(Modify Span Depth) is showing in "Advance configuraton" page even if their is no PD left for the config.(SCGCQ01452129)
- WG:when flashing FW with 16 mb/32 mb.ROM file , LSA throws inappropriate message.(SCGCQ01464425)
- SCGCQ01479375: LSA WebGui: "logs.txt" is generated in logs directory after fresh installation in Linux.(SCGCQ01479375)
- WG: LSA takes some time (2-3 min) in order to display the remote server page after multiple service restarts.(SCGCQ00903348)
- LSA should not allow to select the check box of VD and PD simultaneously on xSDS-None mode.(SCGCQ01323724)
- Issue : Instant Secure erase option is seen when FDE and NON-FDE drives are selected.(SCGCQ01326164)
- SCGCQ01332799: Resolve LSA server compilation issue.(SCGCQ01332799)
- LSA conf file not being updated While changing the default port 2463 and 9000 to some other free ports in windows_8.1_x64.(SCGCQ01375895)
- WG: "?" symbol is in the centre of the Drive erase page unlike in other pages.(SCGCQ01383763)
- WG: ESXi server name is not completely visible in Manage Servers page.(SCGCQ01389332)
- WG: UI Enhancement: Hand symbol has to be given for the "Modify VD" icon for better user experience.(SCGCQ01389343)
- Foreign Configuration issues locked and unlocked foreign drives count.(SCGCQ01391010)
- Action successful message needs to be modified for better User experience.(SCGCQ01392057)
- spandepth need one space between span & depth, to look uniform across the application.(SCGCQ01413225)
- Hide all Vd's in a DG is not working when there is Erase operation is in progress in one of the VD in the same DG.(SCGCQ01423352)
- LSA is not Displaying Both the Foreign Configurations (Encrypted and Unencrypted) for Import/Clear/re scan.(SCGCQ01460076)
- WG: Hide all Vd's in a DG is not working when there is Erase operation is in progress in one of the VD in the same DG.(SCGCQ01394281)
- WG: Help link for "Activate Features" after providing the Activation key is not working.(SCGCQ01398969)
- SCGCQ01424621: PD serial number getting truncated on few PDs.(SCGCQ01424621)
- Added the "?" at the end of instant secure erase. But there no issue related line in more actions panel please find the attached screenshot.(SCGCQ01442352)
- Fixed: LSA app UI cannot be opened when connect M.2 NVME SSD(via HSBP) to LSI 9460-16i/9440-8i.(SCGCQ01474461)
- 'X' symbol for removing physical drives are not highlighted when the drives are allowed to be removed.(SCGCQ01350436)
- API performance Issues pertaining to LSA Build 004.005.000.000( VMware esxi 6.5 ): Raid Mode with JBOD drives.(SCGCQ01467754)

EnhancementRequests:
- Add "Incompatible with Profile" event.(SCGCQ01289924)
- SLIR3: Change build scripts and makefiles to account for change in directory structure and new name of the library.(SCGCQ00293713)
-.(SCGCQ01389581)
- LSA Page tab name should be changed.(SCGCQ01401514)
-.(SCGCQ01416369)
- Upgrade of OpenSSL binaries to openssl-1.0.2l.(SCGCQ01444590)
- Add a new structure to provide OEMs ability to switch to select either I2C or PCIe as an out of band transport.(SCGCQ01445048)
- Update description of MR_DCMD_CTRL_PERSONALITY_SET Dcmd.(SCGCQ01467149)
- SLIR3: Remove Libsysfs dependency in StoreLibIR3.(SCGCQ00293709)
- Adding Solaris and Sparc X64 bit support in SLIR3.(SCGCQ00922699)
- Change library name to SLIT.(SCGCQ00933175)
-.(SCGCQ01309820)
- LSA Server : [Lenovo Purley] Adding tape drive support to Unified LSA for IT Ventura controllers.(SCGCQ01352474)
- HBA nvdata version in Decimal Format in LSA.(SCGCQ01365643)
- WG: Dedicated Hot spare Notification pop-up alignments.(SCGCQ01401505)
- Schedule API changes for time consuming APIs.(SCGCQ01422386)
- MR7.4: Support for FW ER:SCGCQ01389581 in LSA Server.(SCGCQ01428115)
- Update the WebServer Nginx to fix the latest Security Vulnerabilities.(SCGCQ01452493)
- SAS3 Ph8 --- Update Attribution Language - Copyright, Trademark, Confidentiality to Avago.(SCGCQ00729472)
- LSA Client: Handle Progress events without initiating individual API calls.(SCGCQ01416371)
- LSA: Make operation call with query parameter.(SCGCQ01424479)
- Add Test Link Diagnostic API.(SCGCQ01436268)
- WG: Landing page - Graphics improvements.(SCGCQ01401517)
-.(SCGCQ01412749)
- Support for FW ER:SCGCQ01389581 in LSA Client.(SCGCQ01428113)
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01563340)
- LSA7.3: LSA to hide the Empty back plane based on the property field in the LSA.conf file.(SCGCQ01312022)
- LSA: Make operation call with query parameter.(SCGCQ01416374)
- Added MR_MFC_DEFAULTS.NVMeAbortTO and MR_MFC_DEFAULTS.NVMeMaxControllerResetTO.(SCGCQ01532045)
- SCGCQ01250909 - [Lenovo Purley] - Retrieve Boot Events and Maintain it as part of Event History.(SCGCQ01291488)
- Client: EPMR12 porting to MR7.3.(SCGCQ01304973)
- Client: Provide pending profile details in LSA.(SCGCQ01331947)
- LSA Server: EPMR12 defect/feature porting to MR7.3.(SCGCQ01307382)
-.(SCGCQ01356193)
-.(SCGCQ01375857)
- WG: In Remote discovery page Self server is always listed in the last.(SCGCQ01378666)
-.(SCGCQ01472631)

CSETActivities:
- VMware LSI Out of Box driver feature reconciliation.(SCGCQ00696009 port of SCGCQ00652798)
- Provide a StoreLibIR2 deb package to work on Ubuntu.(SCGCQ00795333 port of SCGCQ00630108)
- WG: No Units are displayed for Event ID: 545: Information about super cap health.(SCGCQ01297685 port of SCGCQ01291338)
- LSA throws inappropriate error while attempt to start controller firmware upgrade when pinned cache present on controller.(SCGCQ01297819 port of SCGCQ01288364)
- CSCvd88927 - LSA is displaying drives' type string inconsistently for HDD/SSD so it needs to display consistently.(SCGCQ01331599 port of SCGCQ01316465)
- Hercules_LSA: Event ID-565 does not have any description, shows 0.(SCGCQ01336569 port of SCGCQ01313804)
- Cisco_HSW_Validation_LSA : Expand option can be taken off for degraded R5 volume.(SCGCQ01337104 port of SCGCQ01332737)
- Hercules LSA : Schedule CC button does not allow to click on the whole button.(SCGCQ01339214 port of SCGCQ01337027 )
- PR on all drives are not aborted properly until page refresh is done.(SCGCQ01342568 port of SCGCQ01340808)
- No. of steps shown in "Modify Drive Group" page is not correct.(SCGCQ01343651 port of SCGCQ01341921)
-.(SCGCQ01345364 port of SCGCQ01342479)
- Foreign Import page shows wrong data for the importable LD's.(SCGCQ01345398 port of SCGCQ01332912)
- LSA: LSA should ignore the BBU/SuperCap VPD info failures as it is not a mandatory information.(SCGCQ01347171 port of SCGCQ01346904)
- LSA: LSA should ignore the BBU/SuperCap VPD info failures as it is not a mandatory information.(SCGCQ01347220 port of SCGCQ01346908)
- LSA: LSA should ignore the BBU/SuperCap VPD info failures as it is not a mandatory information.(SCGCQ01347221 port of SCGCQ01346908)
- Cisco_HSW_Validation_LSA: "Simple Configuration" page that appears after creating a simple config is blank.(SCGCQ01347224 port of SCGCQ01345554)
- Cisco_HSW_Validation_LSA: Character limit warning for VD name is not shown while modifying the VD during VD creation.(SCGCQ01347232 port of SCGCQ01345557)
- Cisco_HSW_Validation_LSA: VD Size limit check is not working when user modifies the value of the size.(SCGCQ01350834 port of SCGCQ01346906)
- Cisco_HSW_Validation_LSA: Prepare for removal menu is still displayed even after the option is selected and event is updated.(SCGCQ01350837 port of SCGCQ01338290)
- "%" symbol followed by integer value should not be allowed for the user to enter the size during VD creation.(SCGCQ01350844 port of CGCQ01349556)
- Page scroll doesn't work after VD creation when BG processes on VD are expanded in LSA page.(SCGCQ01351383 port of SCGCQ01349487)
- VD creation fails when a partial VD is added with decimal value & with 1MB strip size to an existing DG.(SCGCQ01354306 port of SCGCQ01348005)
- Security Key provided for importing Foreign Config is not taken by LSA.(SCGCQ01369266 port of SCGCQ01331016)
- Unexpected sense PD messages are flooded in storage log when drive is in spun dwon mode.(SCGCQ01369267 port of SCGCQ01264499)
-.(SCGCQ01375259 port of SCGCQ01373451)
- LSA: Client should not show Unlock drive option if no drives are in locked state.(SCGCQ01378557 port of SCGCQ01331121)
- LSA Server: Windows Make file check-in.(SCGCQ01384621 port of SCGCQ01384618)
- RWC3 Package: Check-in of SL-IT to the package folder.(SCGCQ01384895 port of SCGCQ01384890)
- Cisco_LSA: 'vdname' parameter is missing in the event description that is generated whenever a volume property is modified.(SCGCQ01387017 port of SCGCQ01350435)
- Disabled Phy is not populated from the server when we fire /phys uri.(SCGCQ01389917 port of SCGCQ01389892)
- SCGCQ01385340: Health is not coming proper after foreign config import.(SCGCQ01389918 port of SCGCQ01385340)
- HPE: Un-installation is not removing the folder(s) after performing the Download Diagnostics operation.(SCGCQ01389925 port of SCGCQ01385453)
- WG: Message displayed after flashing the controller FW has to be modified for better presentation - Enhancement.(SCGCQ01391318 port of SCGCQ01389483)
- Hercules LSA : LD properties shows Cachecade Enabled after disabling cache cade.(SCGCQ01419753 port of SCGCQ01417215)
- WG: LSA takes some time (2-3 min) in order to display the remote server page after multiple service restarts.(SCGCQ01440910 port of SCGCQ00903348)
- MR 7.3.1_LSA fails to find server when there is no network.(SCGCQ01500133 port of SCGCQ01482320)
- Cisco - CSCvh55470 - LSA should display proper message for ESXi after LBP/Talladega firmware upgrade/downgrade.(SCGCQ01566052 port of SCGCQ01562368)
- SWR: Device ID is not displayed in LSA..(SCGCQ01566241 port of SCGCQ01564621)
- Changing ini file name to storelibconfit.ini.(SCGCQ01275670 port of SCGCQ01275496)
- For phys-schema.json fails for "([0, u'properties', u'isEnabled', u'enum'], 'False ...".(SCGCQ01309844 port of SCGCQ01304900)
- LSA not allowing to create RAID with 1M strip using 4K drives.(SCGCQ01323613 port of SCGCQ01284395)
- LSA pops-up (504 : Gate Time-out) with StorCLI script to start-stop locate drives with JBOD-Hotspare conversion on.(SCGCQ01324865 port of SCGCQ01260226)
- LSA crashed on pulling out 23 drives connected with 64 LD's in multiple controllers.(SCGCQ01338337 port of SCGCQ01331755)
- Hercules LSA : Cachecade SSD caching should be "enabled" under controller properties.(SCGCQ01339133 port of SCGCQ01337029)
- Hercules LSA : WB and AWB description in LD create page not proper.(SCGCQ01339213 port of SCGCQ01337026)
- User couldn't enter his value in seconds for locating a physical drive.(SCGCQ01344082 port of SCGCQ01332742)
- Cisco_HSW_Validation_LSA: Tooltip for "Simple Configuration" is not shown when other options displays it.(SCGCQ01347225 port of SCGCQ01346851)
- Cisco_LSA: Hyperlink symbol can be shown for "Compare and select" link in Modify Drive Group.(SCGCQ01350847 port of SCGCQ01348107)
- Cisco_HSW_Validation_LSA: Naming convention can be made same across all "Virtual Drive Erase" forms.(SCGCQ01350850 port of SCGCQ01347250)
- cosmetic changes required in "Advanced configuration" page.(SCGCQ01350851 port of SCGCQ01347253)
- DG health is not populated properly in cisco cards.(SCGCQ01350892 port of SCGCQ01349625)
- Virtual Drive Erase form is not closed when it is opened for the second time.(SCGCQ01351381 port of SCGCQ01347243)
- While adding drives to any raid group, Displaying no. of available drives and selected drives can be fine tuned.(SCGCQ01351385 port of SCGCQ01348115)
- Cisco_LSA: "Background Initialization" is misspelled in Event description & one more cosmetic change is required.(SCGCQ01351454 port of SCGCQ01348041)
- In case of FW upload, LSA crash seen with big FW version name.(SCGCQ01351457 port of SCGCQ01338340)
- LSA Client: During the exclusion of the VDs from deletion of one VD leading to the deletion of all the VDs.(SCGCQ01354432 port of SCGCQ01344115)
- WG: Error message is not proper if the username is not provided while verifying server in Manager server page.(SCGCQ01387009 port of SCGCQ01379795)
- Hercules:LSA:Observe that instead of "Feedback " it is named as "FeedBack ".(SCGCQ01389091 port of SCGCQ01388943)
- Updated PD firmware version is not reflecting even after LSA refresh.(SCGCQ01392422 port of SCGCQ01382013)
- SCGCQ01385340: Health is not coming proper after foreign config import.(SCGCQ01393239 port of SCGCQ01385340)
- Hercules LSA: "Prepare for removal" feature should be disabled for drives in LSA.(SCGCQ01401490 port of SCGCQ01396735)
- Activity to check-in build files.(SCGCQ01514879 port of SCGCQ01514834)
-.(SCGCQ01520055 port of SCGCQ01508528)
- Activity to check-in AutoBST files to new MR 7.5 streams.(SCGCQ01564703 port of SCGCQ01564674)
- Updating readme file.(SCGCQ01294583 port of SCGCQ01294570)
- For spares-schema instance validation failed for "u'foreign' is not one of [u'NATIVE', u'FOREIGN', u'MIXED']".(SCGCQ01311504 port of SCGCQ01309617)
- LSA server:LSA not showing the server reboot message after profile set.(SCGCQ01316473 port of SCGCQ01316342)
- HSW_testing_LSA : Could not initialize a VD after disabling and enabling again "Initialize" option.(SCGCQ01321339 port of SCGCQ01309783)
- Cisco_HSW_Validation_LSA : Expand option can be taken off for degraded R5 volume.(SCGCQ01337071 port of SCGCQ01332737)
- Cisco_HSW_Validation_LSA: Size range warning is not shown when user is giving value beyond the limit in MB unit.(SCGCQ01352603 port of SCGCQ01352603)
- LSA not allowing to create RAID with 1M strip using 4K drives.(SCGCQ01369283 port of SCGCQ01284395)
- RWC3 Automation Script files check-in.(SCGCQ01385008 port of SCGCQ01384997)
- LSA/RWC Automation batch files check-in.(SCGCQ01386218 port of SCGCQ01386214)
- Hercules:LSA: trying to open in new tab : "Copyright @ 2017 by Avago Technologies. All Rights Reserved" loads blank page.(SCGCQ01389089 port of SCGCQ01386140)
- Adding tape drive support to Unified LSA for IT Ventura controllers.(SCGCQ01389588 port of SCGCQ01352480)
- SCGCQ01385340: Health is not coming proper after foreign config import.(SCGCQ01392429 port of SCGCQ01385340)
-.(SCGCQ01392506 port of SCGCQ01391775)
- [Lenovo 17B] - LSA- Selected Firmware version doesn't match while upgrading the FW.(SCGCQ01420040 port of SCGCQ01417199)
- Hercules:LSA: Multiple OLH links are opening when clicked on Advance configuration( IE Browser).(SCGCQ01429992 port of SCGCQ01415979)
- LSA Linux BST Automation scripts.(SCGCQ01466009 port of SCGCQ01447013)
- operations-schema.json fails for "u'percentage' is a required property..." in xSDS mode.(SCGCQ01297806 port of SCGCQ01291332)
- Hercules LSA : Auto refresh not happening on Enclosure push pull with 64 VD's configured.(SCGCQ01297821 port of SCGCQ01276760)
- SCGCQ01309545: WG: Issues pertaining to Event ID: 545: Super Cap Health event has redundant data, missing comma's.(SCGCQ01332698 port of SCGCQ01309545)
- Foreign Import page shows wrong data for the importable LD's.(SCGCQ01338335 port of SCGCQ01332912)
- Cisco Validation: FW throws an exception while scheduling Consistency check on R1.(SCGCQ01347254 port of SCGCQ01340788)
- VD size is created with improper size when user creates volume by first decreasing and increasing the size in MB unit.(SCGCQ01350833 port of SCGCQ01346860)
- WG: Hide all Vd's in a DG is not working when there is Erase operation is in progress in one of the VD in the same DG.(SCGCQ01395078 port of SCGCQ01394281)
- Wrong API populated for enclosures operations and schema will fail.(SCGCQ01445408 port of SCGCQ01444689)
- WG: LSA events displays invalid details for unexpected sense events.(SCGCQ01447743 port of SCGCQ01445719)
- WG: the controller operations Query param : 4 has 'premium feature' and 'pinned cache' URI's GET calls in response.(SCGCQ01458204 port of SCGCQ01443879)
- Cisco - CSCvg96681 - LSA-3.163 should display proper message after logout.(SCGCQ01531153 port of SCGCQ01521114)
- MR/IR: Controller Device ID value mismatch in LSA.(SCGCQ01566055 port of SCGCQ01564622)
- Hercules_LSA: Event ID-565 does not have any description, shows 0.(SCGCQ01336556 port of SCGCQ01313804)
- LSA: LSA should ignore the BBU/SuperCap VPD info failures as it is not a mandatory information.(SCGCQ01347125 port of SCGCQ01346904)
- Cisco_HSW_Validation_LSA: Credentials asked during login is not proper when login mode is set to 'Domain Login'.(SCGCQ01347233 port of SCGCQ01341930)
- Hercules-LSA : Updated PD firmware version is not reflecting automatically.(SCGCQ01393283 port of SCGCQ01392496)
- Hercules:LSA: Linux RHEL 6.9: View Event Logs Icon display not proper.(SCGCQ01414738 port of SCGCQ01409445)
- Hercules LSA: Reference to "drive group" while adding logical drive to existing array.(SCGCQ01444720 port of SCGCQ01444670)
- LSA: During the installation "Range of Events" selection is not reflecting in the LSA.conf file.(SCGCQ01472166 port of SCGCQ01472048)
- SCGCQ01479375: LSA WebGui: "logs.txt" is generated in logs directory after fresh installation in Linux.(SCGCQ01480902 port of SCGCQ01313228)
- Fixed: Drive group Migration was disabled with NVME drives DG.(SCGCQ01313228 port of SCGCQ01289586)
- LSA pops-up (504 : Gate Time-out) with StorCLI script to start-stop locate drives with JBOD-Hotspare conversion on.(SCGCQ01324864 port of SCGCQ01260226)
- Spare URI does not respond on iMR Invader.(SCGCQ01378677 port of SCGCQ01376605)
- [PA_2017B_SDV_Lenovo_x3650 M4_Storage] LSA tool update FW Image (oss: 75871) Failed for N2225 SAS HBA(Outback-2) card.(SCGCQ01408778 port of SCGCQ01408626)
- In Standalone LSA periodic automatic refresh is not happening. To display the latest status do manual refresh.(SCGCQ01411632 port of SCGCQ01397546)
- Hercules LSA : LD properties shows Cachecade Enabled after disabling cache cade.(SCGCQ01417213 port of SCGCQ01415347)
-.(SCGCQ01417223 port of SCGCQ01375862)
- LSA: Make operation call with query parameter.(SCGCQ01423429 port of SCGCQ01416374)
- MR7.3_Focused Regression_Strange character when exceeding max number of Uncof good drives on iMR.(SCGCQ01427110 port of SCGCQ01419325)
- LSA: Upgrade of OpenSSL binaries to openssl-1.0.2n.(SCGCQ01564577 port of SCGCQ01563340)
- LSA crashed on pulling out 23 drives connected with 64 LD's in multiple controllers.(SCGCQ01345397 port of SCGCQ01331755)
- Selected firmware version is coming empty for IR/IT/IMR controller.(SCGCQ01354345 port of SCGCQ01321474)
- Hercules LSA: Default write policy for R1 CC VD should be WB instead of WT.(SCGCQ01401352 port of SCGCQ01397557)
- [Lenovo 18A] 110340 - [PA_2017B_SDV_Lenovo_Red_Reno_Storage] Use LSA to configure M5225 and it fail to create VD's from LSA.(SCGCQ01424599 port of SCGCQ01421451)
- Hercules- LSA : VD access policy not showing as blocked for SVD on CC VD offline.(SCGCQ01443687 port of SCGCQ01442554)
- Phase 2 changes for Linux VBAS automation script.(SCGCQ01460081 port of SCGCQ01455968)
- LSA : Silent installation is accepting the invalid options also for LSA/HPE/RWC3.(SCGCQ01472265 port of SCGCQ01389392)
- CSCvd28635: LSA throws inappropriate error while attempt to start patrol read on virtual drive with SSDs.(SCGCQ01319398 port of SCGCQ01284997)
- WG: Trying to import Encrypted VD with Drive security disabled results in error code: 0x11005, it provides No Details to user.(SCGCQ01332824 port of SCGCQ01325783)
- To resolve the merge conflict.(SCGCQ01348161 port of SCGCQ01348057)
- Port Info disappears on doing Drive push pull.(SCGCQ01404636 port of SCGCQ01379323)
- Upgrade of OpenSSL binaries to openssl-1.0.2l.(SCGCQ01444595 port of SCGCQ01444590)
- LSA Windows BST Automation scripts.(SCGCQ01472059 port of SCGCQ01460401)
- LSA 7.6:LSA does not provide the Stop rebuild option in the action pane once the rebuild operation is in progress in Rhel 7.4.(SCGCQ01557665 port of SCGCQ01555955)


3.023.000.000 - Moderate Impact
-------------

2.085.000.000 - Moderate Impact
-------------
- Fixed issue where logs incorrect when remove/insert hdd (SCGCQ01246085)
- Fixed Invalid Server Id as part of event, if server is not in network (SCGCQ01261779)
- Fixed issue where moving PD from slot 0 to another slot, PD slot ID usually still show slot 0 and slot format (SCGCQ01264554)
- Fixed issue where external enclosure serial number in not consistent between LSA, MSM and storcli (SCGCQ01268914)
- Fixed issue where LSA does not list Raid 10 as configurable raid level under configuration service uri when drive mixing is allowed (SCGCQ01037806)
- Fixed issue where Incorrect configurable Volume sizes displayed in LSA for Raid 0(SCGCQ01039518)
- Fixed issue where LSA is not un-installing through the Uninstall-LSA option through Windows All Programs (SCGCQ01039698)
- Fixed issue where VD Properties in LSA was not getting populated for default settings (SCGCQ01043610)
- Fixed issue where controllers/{id}/spares is not populated correctly (SCGCQ01056900)
- Fixed issue where LSA displays only 2 enclosures when four enclosures are connected. (SCGCQ01061548)
- Fixed issue where Enclosure more properties displays "Number of Voltage Sensors" as "0" (SCGCQ01063504)
- Fixed issue where On Number of Temperature Sensors observe that temperature mentioned has 65535 C. (SCGCQ01063924)
- Fixed issue where When the PD is in GHS state LSA is displaying the Prepare for removal option (SCGCQ01064282)
- Fixed issue where LSA does not display the access policy 'hidden' in View Event Logs. (SCGCQ01065622)
- Fixed issue where schedule patrol -read throws an error 'Invalid URI parameter' when user clicks on Finish button. (SCGCQ01066126)
- Fixed issue where Unable to migrate from secured Raid1 VD to Raid5/Raid 6 VD on LSA (SCGCQ01066154)
- Fixed issue where LSA crashes while trying to add a VD to the RAID 00 drive group. (SCGCQ01069405)
- Fixed issue where Simple configuration fails while trying to create VD using SSD Drive (SCGCQ01069412)
- Fixed issue where compared with MSM values of "Date of manufacture" and "Type" is varying. (SCGCQ01069493)
- Fixed issue where Unable to clear or import partial foreign configuration from LSA. (SCGCQ01069580)
- Fixed issue where Ventura: LSA still displays clear button as active even after successfully importing foreign configuration. (SCGCQ01069616)
- Fixed issue where IR3 Events logs are listed reverse sequence in "View Event logs" (SCGCQ01069847)
- Fixed issue where LSA Drive Tab PD "Unconfigured Good" count does not automatically refresh when we Move UG PD to JBOD and vice versa(SCGCQ01069852)
- Fixed issue where Modifying the VD during the VD creation results in option for user to allow more than one cachecade VD, Creation fails (SCGCQ01069898)
- Fixed issue where Instance validation fails for Clear Drive, Stop Clear Drive, Prepare & Undo prepare for removal due to "parameters":{}" (SCGCQ01070441)
- Fixed issue where Instance validation fails for Manage Power Save Settings, Controller PUT operation (SCGCQ01070690)
- Fixed issue where Instance Validation fails for Schedule Consistency Check (SCGCQ01070739)
- Fixed issue where Instance Validation fails for Physical Devices GET (IT controller) (SCGCQ01074960)
- Fixed issue where Server not found warning message is displaying repeatedly one over the other (SCGCQ01075026)
- Fixed issue where Backplane information not displayed under view server profile (SCGCQ01075841)
- Fixed issue where if config cleared during reconfiguration, progress bar does not clear(SCGCQ01075843)
- Fixed issue where hide on DG is not automatically updating the access policy of VDs (SCGCQ01076009)
- Fixed issue where LSA Crashes when we run API performance Script ususally when performing PD Operations GET in Large config (240 PD)(SCGCQ01076023)
- Fixed issue where "Controller Info" of LSA displays driver version of the Gateway server instead of displaying the driver of Vmware server (SCGCQ01076031)
- Fixed issue where "Application Version" in server profile page is displayed as "LSA Server null". (SCGCQ01076146)
- Fixed issue where there were multiple extra columns in PD tab (SCGCQ01077452)
- Fixed issue where the Physical devices are listed in Decreasing order of Device ID instead of ascending order in drive tab (SCGCQ01077563)
- Fixed issue where firmware update does not happen in the Direct agent system from Gateway (SCGCQ01077677)
- Fixed issue where Manage Power save settings with input of " 1 hour" fails with an error " Input Parameters are Invalid" (SCGCQ01078509)
- Fixed issue where Managed Server page provides option of adding gateway server from which we have already logged in to manage server (SCGCQ01078524)
- Fixed issue where Feedback is displayed as FeedBack in LSA. (SCGCQ01079092)
- Fixed issue where After adding server in Manage Server Page intermittently get a junk screen  (SCGCQ01079698)
- Fixed issue where back button does not work in case of Advanced Configuration During VD Creation (SCGCQ01079912)
- Fixed issues pertaining to "Set Patrol Read Properties" Number of PD Count allowed for patrol read (SCGCQ01080265)
- Fixed issue where after logging out from server that is been managed. Clicking Server again in managed server page LSA asks for credentials (SCGCQ01080448)
- Fixed issue where Instance Validation fails for PROGRESS related Operations (SCGCQ01082194)
- Fixed issue where Instance validation fails for "/controllers/0/operations/security" URI : Controller Operation POST (SCGCQ01082618)
- Fixed issue where inappropriate error message is displayed in LSA on flashing fw on IT Intruder (SCGCQ01082897)
- Fixed issue where LSA page does not automatically refresh when PD moved from UG bad to UG Good SS page, CC page does not give option (SCGCQ01083060)
- Fixed issue where on clicking save button on mail server page its shift to Alert Settings without saving that page. (SCGCQ01083063)
- Fixed issue where LSA does not show the default power save mode time set in mfc (SCGCQ01083106)
- Fixed issue where after adding server the managed server list, then logging out, new server cannot be logged into. (SCGCQ01083226)
- Fixed issue where LSA service is not present in the Windows services after downgrading LSA. (SCGCQ01084774)
- Fixed issue where Event Response is giving Default Write Policy: abc (SCGCQ01043609)
- Fixed issue where Sending Invalid HTTP verb in the request for an URI fails with 404 instead of 405 (SCGCQ01059216)
- Fixed issue where texts linked to the health icons "optimal", "critical", "needs attention", in server summary page Should be clickable (SCGCQ01063432)
- Fixed issue where LSA still displays physical disk actions and properties menu when no pd is selected after sorting from Enclosure/slot. (SCGCQ01063524)
- Fixed issue where Instance Validation fails for Simple Configuration POST (SCGCQ01064737)
- Fixed issue where consistency check Schedule parameters is available even after selecting the "Disable" from the Consistency check mode (SCGCQ01069825)
- Fixed issue where LSA not accessible through Chrome browser Version 48.0.2564.109 m (SCGCQ01078618)
- Fixed issue where while initiate ISE against 3rd party locked UG drive, XHR_Header code says "POST 200" but XHR_Response says "Er 77" (SCGCQ01080402)
- Fixed inconsistency between the VD properties displayed in STORCLI when compared with other Apps. (SCGCQ01081145)
- Fixed issue where LSA doesn't get updated without a service restart on Vmware server with IR3 controller. (SCGCQ01081324)
- Fixed issue where matching error description is not shown by client when there is a session already active during login. (SCGCQ01063542)
- Fixed issue where LSA login attempt failed for Vmware Server (SCGCQ01064784)
- Fixed issue where 002.010.000.000 build (Gateway & Standalone) is unable to discover server (SCGCQ01069396)
- Fixed issue where replace drive table does not have device Id column (SCGCQ01075112)
- Fixed issue where LSA does not update the data automatically when Delete VD is performed. (SCGCQ01079635)
- Fixed issue where RWC3-LWM (Windows) is unable to send mail to SMTP (SCGCQ01173361)
- Fixed issue where Ventura IT drive push and pull needs services restart to update the count (SCGCQ01066048, Port of SCGCQ01064904)
- Fixed issue where LSA Allows JBOD Drive having OS to be converted to UG drive, doesnt notify the user on the OS present on JBOD (SCGCQ01067253, Port of SCGCQ01052412)
- Fixed issue where LSA displays "error:Not all values are set successfully" while trying to save power save settings on IMR Ventura. (SCGCQ01067711, Port of SCGCQ01057457)
- Fixed issue where LSA shows blank screen after log in with mutiple controller in the setup (SCGCQ01069360, Port of SCGCQ01068813)
- Fixed issue where intermittent update Ventura firmware hang using LSA ( StorCLI is OK ) (SCGCQ01069565, Port of SCGCQ01038421)
- Fixed issue where user unable to migrate from secured Raid1 VD to Raid5/Raid 6 VD on LSA (SCGCQ01070807, Port of SCGCQ01066154)
- Fixed issue where all the events are not getting downloaded while downloading log from LSA (SCGCQ01145261, Port of SCGCQ01139334)
- Fixed issue where no error message is displayed while importing secure EPD through wrong key (SCGCQ01066088, Port of SCGCQ01063911)
- Fixed issue where user unable to clear or import partial foreign configuration from LSA. (SCGCQ01085466, Port of SCGCQ01069580) 

2.030.000.000 - New Function Only/No fixes
-------------





Lenovo Data Center Group Linux OS Support Home Page
linux.lenovo.com

© 2018-2022 Lenovo. All rights reserved

StorCLI command line tool (For Linux)



StorCLI (Command Line) Utility for Storage Management

Adapters Supported:
 	ThinkSystem RAID 530-8i PCIe 12Gb Adapter  (7Y37A01082)
	ThinkSystem RAID 530-4i Flex Adapter       (7M17A03932)
	ThinkSystem RAID 530-4i Flex Adapter       (7M27A03918)
	ThinkSystem RAID 530-8i Dense Adapter      (SD530 RAID)
	ThinkSystem RAID 530-16i PCIe 12Gb Adapter (4Y37A09727)
	ThinkSystem RAID 540-8i PCIe Gen4 12Gb Adapterr  (4Y37A78834)
	ThinkSystem RAID 540-16i PCIe Gen4 12Gb Adapter   (4Y37A78835)
	ThinkSystem RAID 730-8i 1GB Cache PCIe 12Gb Adapter  (7Y37A01083)
	ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter  (4Y37A09722)
	ThinkSystem RAID 930-8i 2GB Flash PCIe 12Gb Adapter  (7Y37A01084)
	ThinkSystem RAID 930-16i 4GB Flash PCIe 12Gb Adapter (7Y37A01085)
	ThinkSystem RAID 930-24i 4GB Flash PCIe 12Gb Adapter (7Y37A01086)
	ThinkSystem RAID 930-8e 4GB Flash PCIe 12Gb Adapter  (7Y37A01087)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M17A03933)
	ThinkSystem  RAID 930-4i 2GB Flash Flex Adapter      (7M27A03917)
	ThinkSystem  RAID 930-16i 8GB Flash PCIe 12Gb Adapter(4Y37A09721)
	ServeRAID M1210 SAS/SATA Controller    (00JY194)
	ServeRAID M1215 SAS/SATA Controller    (46C9114)
	LSI SAS3004 RAID                       (NA-SAS3004-B)
	LSI SAS3004 RAID                       (NA-SAS3004-N)
	ServeRAID M5210 SAS/SATA Controller    (46C9110)
	ServeRAID M5225-2GB SAS/SATA Controller(00AE938)
	ServeRAID M5215 with 2GB Flash Enablement Flex System x240 M5   (00JX142)
	ServeRAID M5210e SAS/SATA Controller   (46C9117CTO)
	ServeRAID M5120 SAS/SATA Controller    (81Y4478)
	IBM Flex System Storage Expansion Node (68Y8588)
	ServeRAID M5115 SAS/SATA Controller for Flex System  (90Y4390)
	ServeRAID M5100 Series IBM Flex System Flash Kit for X6 (44T1178)
	ThinkSystem RAID 940-8i 4GB Flash PCIe Gen4 12Gb Adapter  for 4Y37A09728
	ThinkSystem RAID 940-8i 8GB Flash PCIe Gen4 12Gb Adapter  for 4Y37A09729
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Adapter  for 4Y37A09730
	ThinkSystem RAID 940-32i 8GB Flash PCIe Gen4 12Gb Adapter  for 4Y37A09733
	ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Internal Adapter  for 4Y37A09735


NOTE TO SERVICE - Reference RETAIN #N/A

007.2008.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.20

Defects:
-Storcli : Copyright shows as year 2021 instead of 2022 & also build release year 2021 instead of 2022 & also build release year shows as 2021 instead of 2022.(DCSG01124638)
-Error seen while flashing psoc.rom in efi CLI.(DCSG01131584)
-storcli 7.2001 does not return values for a bad drive.(DCSG01052072)
-Spellling of mismatch is displayed as "Missmatch" in "Encryption type missmatch" error message..(DCSG01091937)
-Device Type for Backplane in Alilog shown as Enclosure.(DCSG01109911)
-Storcli shows Protection Information (PI) capable drive i.e. "PI eligible" as No, however LSA shows it properly.(DCSG01145223)
-CLI not iterating through MR_SAS_CONNECTORS for H750 controllers.(DCSG01077564)
-Instance validation fails for "/c0 show all" and "controller-detailed-properties-schema.json".(DCSG01035798)
-OS drive name shown as N/A for multiple VDs.(DCSG01101813)
-Storclif reports BBU instead of cachevault for failed retention tests.(DCSG01092227)
-Storclif 7.2005 can't start retention test, says No CacheVault Found!.(DCSG01130532)
-Enclosure logical ID field is not displayed for BP connected to connected to Boca 540-16i controller.(DCSG01024654 (Port Of Defect DCSG01024693))
-Set Patrolread command hangs while setting "excludevd".(DCSG01101780 (Port Of Defect DCSG01102890))
-Strocli.efi utility got hung on issuing "storcli /c0 show" command.(DCSG01049757 (Port Of Defect DCSG01050540))
-"storcli /call show" shows jumbled drives in a Multi IT controller environment.(DCSG01040245 (Port Of Defect DCSG01040583))
-PD size displayed in Gib for some of the 4K drives is incorrect..(DCSG00389591 (Port Of Defect DCSG00994728))
-PD Firmware Release Number = N/A is displayed for drive which has valid Firmware Release Number.(DCSG01083763 (Port Of Defect DCSG01083800))
-Storcli shows success without proper description for "VD delete BBMT" command when no VD present..(DCSG01002466 (Port Of Defect DCSG01024694))
-Update splitpackage script for shenandoah.(DCSG00651204 (Port Of Defect DCSG00994744))
-While trying to import foreign config, Storcli is not showing any drive if user has "Dedicated Hotspare" & also DHS is not displaying along with VD as well.(DCSG01034883 (Port Of Defect DCSG01036901))
-While trying to import foreign config, Storcli is not showing drive as "Hotspare" if the user has only hot spares.(DCSG01028926 (Port Of Defect DCSG01029835))

EnhancementRequests:
-Update ControllerInfo Structure with PartNumber - API Changes.(DCSG01064529)
-Request for Win2022 Supportnfor their 16G Enablement launch, March 2022 RTS.(DCSG00977684)
-MegaRAID key management feature: volatile key escrow.(DCSG00992844)
-secureSignBin: implement feature to download the public key during signing or with explicit arg.(DCSG01035866)
-DCSG01082488
-API change to support PD sanitize operations enhancements.(DCSG01070995)
-Aero 9560/9580 - Add PSOC6 as Vision Controller.(DCSG01056506)
-Add control command MFI_OOB_MCTP_CONTROL_EXCEPTION_NO_CMD (0x99) in API.(DCSG01065378)
-Change the attribute name "Secured" to "Locked" in PD Properties output.(DCSG01040562 (Port Of EnhancementRequest DCSG01040785))
-Handling of VD target-ID's individually even when target-ID is assigned beyond maxLDs.(DCSG01091990 (Port Of EnhancementRequest DCSG01092477))
-Windows Client Win11 OS Support.(DCSG01043616 (Port Of EnhancementRequest DCSG01068906))


007.1907.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.19

Defects:
-While trying to import foreign config, Storcli is not showing any drive if user has "Dedicated Hotspare" & also DHS is not displaying along with VD as well.(DCSG01034883)

007.1707.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------- 
MR 7.17

Defects:
-StorCLI listing failed NVMe drives in non-sorted order.(DCSG00320844
-Instance Validation Failed for "/call/fall show all.json" and foreign-configuration-detailed-schema.json.(DCSG00408509
-MR7.16_storcli: VD creation with the remaining drives fails.(DCSG00303606
-Enclosure position is showing as - for drive detailed properties on an IT controller.(DCSG00286693
-Package Version is not displayed properly after flashing firmware..(DCSG00961822
-PH18 BETA - StorCLI - Update YEAR in the CLI banner.(DCSG00707142
-Storcli launch fails with permission denied message.(DCSG00972016
-Setting CC date and time exceeding the limit, needs to be handled.(DCSG00520110
-"rval - 0" is displayed for "show phyerrorcounters" command..(DCSG00337710
-Storcli lists "/ex show all" for "/cx show all" command..(DCSG00417504
-DiskGroup show all list Hostpare in Unconfigured drive list.(DCSG00359247
-Storcli: learnStartTime displayed incorrectly in command details.(DCSG00320649
-Storcli /cx set debug reset all help description needs an update.(DCSG00521571
-storcli /cx set flushwriteverify help needs an update.(DCSG00507067
-PH17 PA - StorCLI ARM - show file command displays incorrect output for BIOS image.(DCSG00315152
-PH18 PA - StorCLI - appropriate message needed for erase all excludemfg command.(DCSG00395234
-Storcli shows "success" with incorrect message INSTEAD of syntax error for "/c0/d1 set" command..(DCSG00543505
-storcli show alilog shows "SATA-3G" as device interface for 9361-16i.(DCSG00555672
-Handling PBLP component whild displaying Image component versions.(DCSG00301878
-MR_7.17: After Driver unload/load via DDV tools- Ctrl acces via Storcli exit with Segmentation Fault.(DCSG00426317
-coverity: fixing non-array delete and dereferencing before NULL checks.(DCSG00368376
-Handling the read-only file system from storcli.(DCSG00542683
-Updating new SPDM MPI errors.(DCSG00435039
-"Failed Drive not found" reported from enclosure level show repair command.(DCSG00423496
-Controller Lane show command is not working with individual Lanes.(DCSG00386181
-Storcli show command is not displaying remaining drives when PD info fails for one drive.(DCSG00469639
-VD creation fails from storcli even though free capacity is present in DG.(DCSG00757768
-Aero 7.15 CLI shows a extra space in the /c0 set cc h command.(DCSG00298943
-Instance Validation Failed for "/call show" and controller-properties-schema.json.(DCSG00408497
-show alilog command displays JBOD as volumes.(DCSG00556934
-Instance Validation Failed for "/call/fall import preview.json" and foreign-configuration-detailed-schema.json.(DCSG00408512
-Max commands for averaging needs to be removed from DPMstat RA output.(DCSG00286349 (Port Of Defect DCSG00306711)
-Failure observed while running set sbr command.(DCSG00779151 (Port Of Defect DCSG00932922)
-Storcli "/call/eall/sall download status" error message needs correction..(DCSG00735452 (Port Of Defect DCSG00757676)
-Unified StorCLI MR7.15 - Fixing coverity issues - Part 1.(DCSG00290662 (Port Of Defect DCSG00368612)
-Atlas 4.2: StorCLI lists wrong error message "Failed in standard Inquiry", when user tries to upgrade/downgrade all connected NVMe Drives FW at a time.(DCSG00309398 (Port Of Defect DCSG00313432)
-The foreign config of DHS/GHS details is not listing under foreign config import preview.(DCSG00919659 (Port Of Defect DCSG00935761)
-Invalid Array Size in ZB is displayed for Degraded R1 span Foreign VD in storcli foreign import preview.(DCSG00916209 (Port Of Defect DCSG00935751)
-Logical ID of Cobra expander not displayed properly in Storcli and LSA.(DCSG00342456 (Port Of Defect DCSG00391477)
-CLI crashes when issuing the phyerrorcounters command on a 14G Expander backplane.(DCSG00323054 (Port Of Defect DCSG00323721)
-Show command status not proper when issued with wrong EID.(DCSG00906544 (Port Of Defect DCSG00935762)
-Storcli shows no output for valid parameter for "/c0/p0,1,22 show" command..(DCSG00840944 (Port Of Defect DCSG00932927)
-From the CLI failed to convert UBAD state drive to UGOOD.(DCSG00391494 (Port Of Defect DCSG00391509)
-Non Foreign drives GHS are listing under Foreign import preview.(DCSG00931210 (Port Of Defect DCSG00935765)
-Storcli "show file" command does not report correct FW version.(DCSG00299788 (Port Of Defect DCSG00302030)
-Storcli show incorrect property name for "/c0/d0,3 set hidden=off" command..(DCSG00733214 (Port Of Defect DCSG00758467)
-Coverity fixing bad allocator and resource leaks.(DCSG00307346 (Port Of Defect DCSG00307355)
-Vses Device Type is displayed as Enclosure for IT card.(DCSG00920244 (Port Of Defect DCSG00935772)
-StorCLIF fail to flash firmware image of BTBL (BOOT_BLOCK) on Invader MR.(DCSG00330381 (Port Of Defect DCSG00353198)
-Storcli throws junk value is shown on set consistency check.(DCSG00906989 (Port Of Defect DCSG00935693)
-MR 7.15 StorCLI : Addressing Coverity defects.(DCSG00286677 (Port Of Defect DCSG00311222)
-CLI Version info is seen in continuation of Sense data when executed show events.(DCSG00935802 (Port Of Defect DCSG00935973)
-VDs imported from Jbod mode to RAID do not have OS name available in Linux OS.(DCSG00968023 (Port Of Defect DCSG00975216)
-CLI failing to stop a BGI or CC when paused..(DCSG00735544 (Port Of Defect DCSG00757870)
-Enclosure phyerrorcounters fails in VMware platform.(DCSG00706496 (Port Of Defect DCSG00706497)
-Storcli shows success for "set patrolread excludevd" command failure in the presence of VD..(DCSG00906735 (Port Of Defect DCSG00935770)
-For empty SPDM slots 0 & 1 show security slot info command shows as Invalid data on IT controller..(DCSG00348125 (Port Of Defect DCSG00353186)
-Segmentation fault noted with drive firmware update.(DCSG00758645 (Port Of Defect DCSG00932904)
-VD creation output shows VD size as 0KB when it reaches maximum supported virtual disks(64VDs) in a DG..(DCSG00349415 (Port Of Defect DCSG00353914)
-SAS drive Inquiry data is not shown in drive show all output.(DCSG00778367 (Port Of Defect DCSG00932917)
-Fixing Coverity defects of MR 7.15.(DCSG00299981 (Port Of Defect DCSG00309219)
-Post reboot incorrect lane speed is displayed in Storcli when user sets it to 16GT/s.(DCSG00383336 (Port Of Defect DCSG00395901)
-On storcli /c0/v1,2,3,4 del if anyone of the vd in the series is not present then all the vd's are not deleted.(DCSG00264571 (Port Of Defect DCSG00266888)
-Coverity defects - remove resource leaks, invalid types in function arguments.(DCSG00269017 (Port Of Defect DCSG00277861)
-Storcli will not show LargeIOsupport is enabled/disabled on the controller.(DCSG00353195 (Port Of Defect DCSG00353882)
-Storcli shows target id of the drive as boot drive instead of showing drive slot number for JBOD drives..(DCSG00344079 (Port Of Defect DCSG00353203)
-MR7.15_storcli: With the latest storcli, VD creation with the remaining drives fails.(DCSG00278049 (Port Of Defect DCSG00282590)
-Removed leading spaces for SATA drives.(DCSG00904104 (Port Of Defect DCSG00935692)
-Drives connected to IT controller reports Shield Counter.(DCSG00244631 (Port Of Defect DCSG00266881)
-Size of Degraded R10 Foreign VD is displayed as 0 KB in storcli.(DCSG00916207 (Port Of Defect DCSG00935746)

EnhancementRequest:
-Adding new License file and updating the build script to include the new file.(DCSG00324401
-Add CLI command to control Parity Read Cahce Bypass for SSD VDs.(DCSG00342282
-MR7.16 : Support WJ Pinning for both WB and WT Parity RAID VDs.(DCSG00214472
-Provide option in storcli to disable / enable the Preboot trace Buffer feature in MR FW..(DCSG00310366
-Enable cache retention testing on Shenandoah controllers for factory testing.(DCSG00340899
-Updating storcli code and makefiles to support VBAS builds on GCP.(DCSG00412063
-Additional NameSpace behavior changes.(DCSG00310386
-Updating storcli BST scripts to support new VBAS Auto BST procedure.(DCSG00282976
-StorCLI: Automate the test cases specific to MR7.17 Product Requirements.(DCSG00433350
-Add support for reporting SPDM Measurement Specification and Hash Algorithm.(DCSG00301782
-Updating command legends as per the command output.(DCSG00083851
-IT Drive Model Number , Revision for SATA drives displayed in full.(DCSG00371061
-MR7.16: StorCLI does not show the SAS Address of the enclosure.(DCSG00255109
-Unified StorCLI 7.17 - x64 UEFI VBAS / GCP support.(DCSG00559813
-Updating Error Strings for NVME init error codes in Apps.(DCSG00434066
-MR7.16 StorCLI: Ruby SED Support.(DCSG00264744
-CLI to handle ERROR_BUSY from Windows storport.(DCSG00348813 (Port Of EnhancementRequest DCSG00353214)
-Displaying "OS name" for VDs imported from EHBA mode to RAID.(DCSG00775114 (Port Of EnhancementRequest DCSG00932911)
-Display Enclosure serial No in Storcli.(DCSG00500922 (Port Of EnhancementRequest DCSG00932906)
-Request to add checks (DevId, SubDevice Id) check prior to flashing.(DCSG00500924 (Port Of EnhancementRequest DCSG00521828)
-SEKM Support in CLI.(DCSG00433143 (Port Of EnhancementRequest DCSG00935780)
-CLI: Package Stamping Verification During Firmware Update.(DCSG00239672 (Port Of EnhancementRequest DCSG00282815)
-StorCLI has the ability to switch the OOB mode.(DCSG00547179 (Port Of EnhancementRequest DCSG00935783)
-SMART Polling Improvement - PERC 10.(DCSG00249963 (Port Of EnhancementRequest DCSG00282814)
-PERCcli turn off logging by default.(DCSG00255367 (Port Of EnhancementRequest DCSG00282813)
-Remove the MFG date, Revision date and Rev from IT StorCLI output.(DCSG00415059 (Port Of EnhancementRequest DCSG00418372)
-Display port information for NVMe Init failed drives.(DCSG00359418 (Port Of EnhancementRequest DCSG00421187)
-storcli "set good" command can still be used for JBOD EPD-PT drives.(DCSG00318591 (Port Of EnhancementRequest DCSG00353919)
-PERC11.1 - Dual x8 Support for 16 port Controllers.(DCSG00299060 (Port Of EnhancementRequest DCSG00323772)

007.1513.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------- 
MR 7.15

Defects:
-CLI Version info is seen in continuation of Sense data when executed show events.(DCSG00935802)
-Handling the read-only file system from storcli.(DCSG00938327 (Port Of Defect DCSG00542683))

Enhancements:
-Request to add checks (DevId, SubDevice Id) check prior to flashing.(DCSG00930193 (Port Of EnhancementRequest DCSG00500924))


007.1510.0000.0000  - Moderate Impact/Low Probability of Occurrence
-------------------- 
MR 7.15

Defects:
-From the CLI failed to convert UBAD state drive to UGOOD.(DCSG00391494)
-PH17 PA - StorCLI ARM - show file command displays incorrect output for BIOS image.(DCSG00320641 (Port Of Defect DCSG00315152))
-StorCLI listing failed NVMe drives in non-sorted order.(DCSG00321815 (Port Of Defect DCSG00320844)
-MR 7.16: Storcli: learnStartTime displayed incorrectly in command details.(DCSG00321908 (Port Of Defect DCSG00320649))
-rval - 0" is displayed for "show phyerrorcounters" command..(DCSG00337735 (Port Of Defect DCSG00337710))
-DiskGroup show all list Hostpare in Unconfigured drive list.(DCSG00360517 (Port Of Defect DCSG00359247))
-Controller Lane show command is not working with individual Lanes.(DCSG00386184 (Port Of Defect DCSG00386181))
-storcli /cx set flushwriteverify help needs an update.(DCSG00541982 (Port Of Defect DCSG00507067))
-"Failed Drive not found" reported from enclosure level show repair command.(DCSG00430578 (Port Of Defect DCSG00423496))
-Storcli show command is not displaying remaining drives when PD info fails for one drive.(DCSG00489855 (Port Of Defect DCSG00469639))
-Storcli /cx set debug reset all help description needs an update.(DCSG00538790 (Port Of Defect DCSG00521571))

EnhancementRequest:
-Display Enclosure serial No in Storcli.(DCSG00500922)
-IT Drive Model Number , Revision for SATA drives displayed in full.(DCSG00405900 (Port Of EnhancementRequest DCSG00371061))


007.1326.0000.0000  - Moderate Impact/Low Probability of Occurrence
-------------------- 
Defects:
-Foreign Config Preview shows empty data when Foreign config is present with Rebuild is in Progress.(DCSG00261203)
-Inconsist DG number in StorCLI.(DCSG00235157)
-RTTdump shows success but it fails to download the dump..(DCSG00253652 (Port Of Defect DCSG00253719))
-Incorrect Adapter type shown in the perccli show all output.(DCSG00241405 (Port Of Defect DCSG00244145))
-Expander firmware download using with mode 5 option fail with error message..(DCSG00239524 (Port Of Defect DCSG00240685))
-With length command, CLI says Memory Exhausted.(DCSG00235628 (Port Of Defect DCSG00236791))
-Enclosure position is showing as - for drive detailed properties on an IT controller.(DCSG00286693 (Port Of Defect DCSG00286701))
-Observe CLI Crash on windows while setting Autoconfig option.(DCSG00253642 (Port Of Defect DCSG00253722))
-MR7.15_storcli: With the latest storcli, VD creation with the remaining drives fails.(DCSG00278049 (Port Of Defect DCSG00282592))
-"No Controller found" shown when controller is busy..(DCSG00248017 (Port Of Defect DCSG00253661))
-On storcli /c0/v1,2,3,4 del if anyone of the vd in the series is not present then all the vd's are not deleted.(DCSG00264571 (Port Of Defect DCSG00266886))
-Connector Name is incorrectly displayed when connector count goes beyond 8.(DCSG00249023 (Port Of Defect DCSG00252701))
-MR 7.15: Storcli: Instance Validation Failed for "virtual-drive-config-schema.json" and "/call delete config force".(DCSG00247992 (Port Of Defect DCSG00253761))
-With new MR API changes, storcli shows failure while changing accesspolicy.(DCSG00257307 (Port Of Defect DCSG00258140))
-MR 7.15: Storcli: Instance Validation Failed for "enclosure-fw-download-schema.json" and "enclosure FW download" output..(DCSG00250066 (Port Of Defect DCSG00253733))
-Show expansion shows wrong output in presence of JBODs..(DCSG00247163 (Port Of Defect DCSG00252417))
-Enclosure position value not listed properly in show all command.(DCSG00254935 (Port Of Defect DCSG00256384))
-Drives connected to IT controller reports Shield Counter.(DCSG00244631 (Port Of Defect DCSG00266894))
-Expander firmware download help need to be corrected for IT controller..(DCSG00239870 (Port Of Defect DCSG00240680))

EnhancementRequests:
-To add return status MFI_STAT_OK_REBOOT_REQUIRED to MR_DCMD_LD_SET_PROPERTIES in mr.h.(DCSG00256271)
-Additional FDE type for Ruby SED support.(DCSG00055878)
-MFI SMP Port Num API changes.(DCSG00257777)
-MR7 API: Add package incompatibility reporting.(DCSG00231443)
-SMART Polling Improvement - API Changes.(DCSG00246317)
-Implement customSign.exe CLI wrapper utility to help customers sign with their private key.(DCSG00234646)
-Changes to support 16port connection to Expander with AeroIOC.(DCSG00254845)
-Updating storcli BST scripts to support new VBAS Auto BST procedure.(DCSG00282976 (Port Of EnhancementRequest DCSG00290359))

007.1325.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------  
MR 7.13
Fix issue:
DCSG00235157 - Inconsist DG number in StorCLI
Description:
Customer reported the DG/Array/Row is incorrect to get from storcli and it causes "insert" command failure. 

007.1324.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------  
MR 7.13
Defects:
-Storcli: Optl not mentioned in /call/dall show output..(DCSG00065740)
-Instance Validation Failed for "/call set smartpollinterval=300" and controller-smartpollinterval-schema.(DCSG00057141)
-StorCLI crash when create VD.(DCSG00052275)
-/e: and /s: is not mentioned in the Convention for /storcli64 /c0/v0 start migrate detailed ?.(DCSG00143788)
-BZ(186687):[AMD2P & Whitley] EXSi 7 can't boot up after install storcli.(DCSG00048516)
-Storcli show Device type as backplane while no drives are connected.(DCSG00074732)
-Help Description for Migrate shows "operation" printed twice in Storcli output..(DCSG00063696)
-Instance Validation Failed for "/call show" and controller-properties-schema.json.(DCSG00057213)
-Coverity analysis - Fixing uninitialized variables, resource leaks, and return statements - Part 1.(DCSG00046195)
-Foreign topology table display BT as "Y" for drives which are in foreign state..(DCSG00068453)
-Storcli: Same help description across "/c0/e0 show" and "/c0/e0 show all"..(DCSG00064748)
-While executing perccli, by default log file with storcli.log is getting generated..(DCSG00038031)
-MR 7.13: Storcli(Regression): Syntax error seen while using "nolog" and "page" together as parameters.(DCSG00071417)
-In Aero behind atlas configuration "NVME" drive firmware revision shows wrong.(DCSG00049614)
-Storclif command for battery retention test issues command to start retention test which is an unsupported command.(DCSG00058688)
-Show DPM with type LCT is not giving proper output and register DPM commands for all OS.(DCSG00033459)
-Storcli: ProdID Legend abbreviation missing in /c0/eall show output..(DCSG00063317)
-FW sometimes allows an invalid CLI command (set personality=HBA) to be successful and sets the personality to eHBA mode.(DCSG00129542)
-Fixing Coverity defects.(DCSG00044004)
-Unable to create JBOD using the legacy command with latest Perccli.(DCSG00118670)
-MR 7.13: Storcli: GHS is shown as revertible.(DCSG00065815)
-In the presence of Locked Foreign config, "/c0/fall del" shows incorrect output..(DCSG00062615)
-StorCLI - '/c0 show nolog' reported as Un-supported Command.(DCSG00071410)
-Set VD policy to WB (unsupported )should return failure in JBOD personality..(DCSG00076992)
-Shenandoah_MRSA: Enclosure Bay count coming Wrong in CLI.(DCSG00074731)
-Shenandoah_Storcli : Legend for ID in JBOD list is missing.(DCSG00069312)
-Incorrect Legend abbreviation in storcli show output.(DCSG00058874)
-MR 7.13: Storcli: controller add commands are listed along with vx commands..(DCSG00065744)
-Even on giving wrong 'storclif delete config' command syntax, the config is cleared successfully without any error.(DCSG00055164)
-Storcli.efi shows incorrect note for unsupported commands for MR controllers.(DCSG00056335)
-VMware peccli, percli64 and storcli64 bit binary loads library from storcli 32 bit's installation path.(DCSG00074600)
-StorCLI - /c0/eall/sall start locate not working for second enclosure connected.(DCSG00040244)
-Instance Validation Failed for "/call show dpm" and controller-dpm-schema.json.(DCSG00057194)
-Command description should be modified for storclif /cx set activityforlocate=.(DCSG00069746)
-MR 7.13: Storcli: bbu not described in convention details.(DCSG00066314)
-Shenandoah_storCLI: Add vd command for r0 getting successful with 512KB when mazStripeSize is 1MB.(DCSG00057003)
-Fixing Coverity defects, uninitialized, unused variables and memory leaks.(DCSG00052049)
-Start_entry is not a command parameter in show events command.(DCSG00067937)
-On OS /cx/dall split mirror command shows success when there is no drive groups.(DCSG00069690)
-Update the storcli readme with for Esxi 6.x and Esxi 7.0 releases.(DCSG00055533)
-Extended the abbreviation in the legends.(DCSG00069703)
-Shenandoah : storcli : Energy Pack show present for MR 216i controller , where the hardware is not supported.(DCSG00053888)
-"set sbr" command mentioned in detailed help but not listed in help output..(DCSG00068444)
-Creation of VD for with more than 64 drives is failing with "Cannot create configuration with x drives".(DCSG00056544)
-Description of compare firmware ver command does not mention as IT supported command.(DCSG00070258)
-Command description should be modified for /cx set alarm command.(DCSG00069709)
-MR 7.13 : RSOD is seen for storcli.efi show command when the controller is in invalid state.(DCSG00066879)
-StorCLI /cx restart is not supported in UEFI environment should be mentioned in help..(DCSG00068879)
-Remove deprecated command 'show adpcount' from Ubuntu folder(readme).(DCSG00058329)
-Segmentation fault seen while running OCR and Patrol read in loop on ESXi7.0 OS..(DCSG00066854)
-Instance Validation Failed for "/call/fall import preview" and foreign-configuration-detailed-schema.json.(DCSG00068868)
-Field for CV is missing in table as well as in legend for storcli64.exe show command.(DCSG00067075)
-Restrict discovery of PERC HBA through StorCLI(Static binary).(DCSG00077037)
-PH14 Alpha Aero - StorCLI - Difference in output noted for /cx/px set state command.(DCSG00055119)
-MR 7.13 : Enclosure Device ID is mentioned in the legend for /cx/vall show command.(DCSG00067878)
-MR 7.13 : Cosmetic issue is seen in the command name of /cx /cx show memscrubpatterns ?.(DCSG00067877)
-Commands displayed twice in help description..(DCSG00068441)
-Storcli DPM does not use legend "Resp" in EXT output.(DCSG00060706)
-Enclosure ID is not mentioned as optional in "add Vd " command.(DCSG00058867)
-Port information coming as internal and Location as Blank in when all the drives are removed from UBM2 Backplane.(DCSG00071756)
-DPM delete help is listed under drive delete command group.(DCSG00053537)
-No mention on convention in restart command description..(DCSG00068542)
-Fixing Coverity defects - Uninitialized variable, resource leaks and null referencing.(DCSG00041202)
-Set the PR to run on only configured array, but it complete the PR along with un-configured area..(DCSG00067103)
-Fixing Coverity issues - Resource leaks.(DCSG00054690)
-Storcli throws incorrect error message for /c0 add vd each r0 when Ubad drive is present in the setup..(DCSG00069698)
-Use NVRAM to save PTB information -- API changes.(DCSG00082981)
-Debug logs in FreeBSD is logging timestamp in different lines.(DCSG00069730)
-"/c0 show nolog" shows as "un-supported command.(DCSG00068482)
-Shenandoah_Storcli : The status of PD FW update on multiple drives is not proper when parallel is not included.(DCSG00069693)
-Device type of UBM backplane is displayed as expander in Valvano-32i Controller managed port(C3)..(DCSG00054275)
-Shenandoah_PA2:StorCLI not branding compliant for VD creation command Failure case -IO Policy specif.(DCSG00049610)
-Storcli: px is not described in convention details..(DCSG00065742)
-Unmap enabled not listed for unmap enabled VDs with /cx/vall show all cli command.(DCSG00112331)
-Instance Validation Failed for "storcli64.exe show" and system-schema.json.(DCSG00057156)
-Not able to create R1/R10 with 1MB size and strip size is 1MB.(DCSG00058162)
-Description for storcli output is not proper after collecting the snapdump with id=all.(DCSG00063626)
-StorCLI not reporting default oob settings from nvdata value.(DCSG00066530)
-Executing storcli commands from external path throws error.(DCSG00072117)
-StorCLI: /storcli /cx add vd verbose help ,strip size 512 is missing in help description under strip sizes..(DCSG00146343)
-MR 7.13: Storcli: Caution mentioned instead of note..(DCSG00066554)
-perccli is Reporting incorrect scheduled BBU Learn Date.(DCSG00109638)
-Coverity analysis - Fixing uninitialized variables, resource leaks, and return statements.(DCSG00046460)
-Storcli64.exe /c0 show freespace shows unnecessary data when freespace is not present.(DCSG00055686)
-Schema mapping list is not updated with DPM commands.(DCSG00057823)
-Foreign DHS drive state is displayed as UGood under /c1/fall show all tab..(DCSG00068427)
-MR 7.13: Storcli: logfile is not described in show dpmstat command..(DCSG00065838)
-Statistics is spelled as Statitics in dpm stat commands.(DCSG00057112)
-Cache Vault should be placed instead of battery for "storcli /cx/cv show status ?" help.(DCSG00143868)
-Exit code showing "0" for failed storCLI command due to syntax error.(DCSG00054313)
-Removal of log type from storcli logs.(DCSG00046794)
-Discription for the term "NoVDs" is missing in the legends.(DCSG00068592)
-start dpm returned error.(DCSG00035436)
-Storcli: Show latest events output print shows 0.00 for all the number of events dumped (expected is the number of events queried for).(DCSG00068877)
-Incorrect message noted when Ventura firmware flashed on Aero board.(DCSG00046031)
-No consistency in the help details of "/c0/ex download" commands.(DCSG00064745)
-Storcli license file is not present in the Vmware, Ubuntu & EFI folders.(DCSG00056538)
-Storcli issuing 'add vd r0 drives=all' causes storcli to crash.(DCSG00053963)
-No syntax error for multiple usage of "nolog" parameter in the command..(DCSG00066729)
-Re-Host information is blank when ASO is not enabled.(DCSG00072628)
-SSD Wear guage Parameter "SSD Percent used" to be removed from CLI.(DCSG00074791)
-MR 7.13: Storcli: sx not described in convention details..(DCSG00066310)
-Error message is improper for invalid raid level in volume creation.(DCSG00081057 (Port Of Defect DCSG00083789))
-Set MFG command does not throw an error when executed with empty file..(DCSG00074178 (Port Of Defect DCSG00074209))
-VD delete command works with multiple force options.(DCSG00165527 (Port Of Defect DCSG00167329))
-Syntax error for /c0 show AliLog ?.(DCSG00109790 (Port Of Defect DCSG00112470))
-storcli faults when issue drive poh command on Linux.(DCSG00075870 (Port Of Defect DCSG00075875))
-show memscrubpatterns shows status as success but failed in the description.(DCSG00077082 (Port Of Defect DCSG00103214))
-PH15 PA StorCLI - Segmentation fault observed when Sea IT PSOC image flashed on Ventura.(DCSG00075626 (Port Of Defect DCSG00212680))
-Wrong enclosure details are displayed when slot details are queried..(DCSG00127133 (Port Of Defect DCSG00139981))
-Storcli_VMWare gives failure messages when user tries to set the lanespeed.(DCSG00167210 (Port Of Defect DCSG00167280))
-"Download cpld" command displays incorrect output for MR controller..(DCSG00075734 (Port Of Defect DCSG00075863))
-The properties displayed in the command show htbparams has misspelled fields.(DCSG00104056 (Port Of Defect DCSG00105681))
-Instance Validation Failed for "/call/fall show" and foreign-configuration-schema.json.(DCSG00076415 (Port Of Defect DCSG00078173))
-storclif.exe /cx set copyback ? shows incorrect command name..(DCSG00075718 (Port Of Defect DCSG00075890))
-No description mentioned for "/cx set eghs" command..(DCSG00074290 (Port Of Defect DCSG00074768))
-Unified StorCLI Phase 15: storcli64 /cx add vd each help file missing options and format inconsistencies.(DCSG00139659 (Port Of Defect DCSG00139995))
-Aero Controller DPM does not report Max Response Time under 1 ms..(DCSG00099365 (Port Of Defect DCSG00102548))
-Storcli: Wrcache is mentioned instead of WT| WB.(DCSG00074284 (Port Of Defect DCSG00074767))
-Storclif allows to set Set SubOEMID as 1000 and more.(DCSG00079932 (Port Of Defect DCSG00080836))
-Description for storcli output is not proper after collecting the snapdump with id=all.(DCSG00031711 (Port Of Defect DCSG00063602))
-Storcli /cx show cc , does not shows the "Unit" for CC execution Delay..(DCSG00126229 (Port Of Defect DCSG00129753))
-storcli64.exe /c0/e1/s1 start sanitize throws syntax error..(DCSG00129738 (Port Of Defect DCSG00129750))
-forcehcb is executed with incorrect description in OS level..(DCSG00080961 (Port Of Defect DCSG00083295))
-"Show alilog" command output shows invalid PD ID in Virtual drive info..(DCSG00167354 (Port Of Defect DCSG00167449)
-force is not defined under OPTIONS in storcli64 secureerase help file.(DCSG00148255 (Port Of Defect DCSG00150480))
-Storcli displays "Returned SCSI status for the command : Check condition" along with regular command.(DCSG00138580 (Port Of Defect DCSG00139200)
-Aero Alpha: Storcli stops functioning during run of attached script.(DCSG00034379 (Port Of Defect DCSG00039682)
-/vx is mentioned in the convention for storclif64.exe /cx set cc detailed ?.(DCSG00075700 (Port Of Defect DCSG00075894))
-DCSG00096587.(DCSG00104055 (Port Of Defect DCSG00108742))
-Avenger: ./storcli2 /c0 show ds all command(not present) shows the output of /c0 show all.(DCSG00061163 (Port Of Defect DCSG00080485)
-PATH_1 and PATH_BOTH assigned drives not getting displayed under storcli in WF DDROCK setup.(DCSG00050891 (Port Of Defect DCSG00079275))
-Storcli output starts with "GetCtrlInfo : ProcessLibCommand failed; retCode = 0xFF" for all command.(DCSG00214170 (Port Of Defect DCSG00214248))
-"OS Drive Name" does not display the details in "vall show all" for esxi OS.(DCSG00102559 (Port Of Defect DCSG00103190))
-Storcli: "show bbmt" displays output for an invalid VD..(DCSG00228667 (Port Of Defect DCSG00230346))
-Storcli command description shows none for Download firmware failure.(DCSG00221431 (Port Of Defect DCSG00223281))
-Instance Validation Failed for /call/show_all.json and controller-detailed-properties-schema.json.(DCSG00132488 (Port Of Defect DCSG00137828))
-NoVDs is displayed in dall show output..(DCSG00074628 (Port Of Defect DCSG00074763))
-"reset errorcounters" command mentions options under conventions.(DCSG00074288 (Port Of Defect DCSG00074764))
-PH16 PA - StorCLI - Compare fwprodid help page needs to be updated.(DCSG00167732 (Port Of Defect DCSG00215133))
-Display basic secure boot details for Sea IT controller.(DCSG00074184 (Port Of Defect DCSG00074218))
-No consistency in the description of Force option.(DCSG00074283 (Port Of Defect DCSG00074765))
-Storcli /c0/eall show status extended command fails to generate any output for ARM server backpla.(DCSG00146359 (Port Of Defect DCSG00150479))
-Debug log configuration file for perccli is taking storcliconf.ini.(DCSG00074691 (Port Of Defect DCSG00074757))
-Compare fwprodid command fails for 9500-16i.(DCSG00092943 (Port Of Defect DCSG00115266))
-Handling of controller properties related to drive FW download.(DCSG00138192 (Port Of Defect DCSG00139266))
-In command storcli /cx/ex/sx show DPM type=Ext , Sectors Read (Written) is not displayed correctly.(DCSG00083167 (Port Of Defect DCSG00103210))
-Ph16 PA: Storcli crash observed while running show all with NVMe drives connected.(DCSG00150686 (Port Of Defect DCSG00167881))
-Description for "profileid=" is missing in help and detailed help.(DCSG00152251 (Port Of Defect DCSG00152935))
-EKMS Boot Agent Status is not updating properly..(DCSG00049004 (Port Of Defect DCSG00050289))
-MR 7.15: Storcli: Force option is mentioned as "For".(DCSG00223195 (Port Of Defect DCSG00225259))
-Storcli displays 255 max spin-up drive count in help description instead of 240.(DCSG00098081 (Port Of Defect DCSG00108741))
-"Compare factorysettings" command displays incorrect output for wrong input file.(DCSG00075762 (Port Of Defect DCSG00075888))
-Storcli64 /cx show spinupdrivecount help file description needs update.(DCSG00150052 (Port Of Defect DCSG00150459)
-Segmentation with controller show summary command when controller is in unsupported state.(DCSG00215109 (Port Of Defect DCSG00215118))
-StorCLI show autoconfig does not display all properties it can set.(DCSG00071834 (Port Of Defect DCSG00080859))
-Storcli returns wrong Operating system in Windows..(DCSG00037088 (Port Of Defect DCSG00037336))
-No description for "set autoconfig=R0 immediate" command..(DCSG00129610 (Port Of Defect DCSG00129762))
-Displaying connected portnumber as per API supportMoreThan16Phys.(DCSG00104331 (Port Of Defect DCSG00108740))
-Compare Factory command execution fails in storclif.(DCSG00074182 (Port Of Defect DCSG00074207))

EnhancementRequests:
-HPE : Windows and Linux StorCLI signing.(DCSG00053511)
-Implement changes to secureSign signing tool and infrastructure to support mixed list of PublicKeys that are from SCGCQ and DCSG..(DCSG00105430)
-API change to support ISE completion status.(DCSG00065881)
-MR API: Change event class for SPDM events.(DCSG00134416)
-API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI.(DCSG00222915)
-Perccli: Need a mechanism to get supported device protocols for each controller form factor.(DCSG00117742)
-support for sanitize command.(DCSG00108999)
-Shenandoah: Support for the New Energy Pack states.(DCSG00043240)
-Preboot Trace Buffer [PTB] for Ventura/Aero - MR API.(DCSG00060713)
-Remove Help Text for lanespeed commands.(DCSG00099939)
-Shenandoah: Change the CLI installation Directory name from Megaraid to hpe.(DCSG00053988)
-Porting storcli source from V8 Clearcase to CC9 GCP database.(DCSG00013486)
-Creating VD with 0 MB or GB should not be allowed to succeed --ve case boundary value scenario.(DCSG00048859)
-MR API: NVME Drive Init Error Report and Repair for Aero/Ventura.(DCSG00071534)
-DCSG00129388
-Support to display drive connector name information for SAS3.5 IT Controllers.(DCSG00120994)
-Add segment area into pci information of Megaraid controller in storcli.(DCSG00032694)
-Populate secureboot properties "KeyUpdatePending" and "Remaining Secure Boot Key slots" in StorCLI.(DCSG00101684)
-Remove (hide) PCIe Link form in HII and from CLI for Perc11.(DCSG00077856)
-Define MR_SAS_PHY_CONNECTION.currentSpeed when no devices are connected.(DCSG00071066)
-Signing Linux executables via GPG method in HSM.(DCSG00077215)
-Shenandoah: Creating VD with 0 MB or GB should not be allowed to succeed - Part 2.(DCSG00053587)
-Shenandoah: SSD Wear Gauage.(DCSG00046064)
-MR API changes - Support new DCMD for Platform Security SPDM.(DCSG00068355)
-Add /px linkspeed back to help text.(DCSG00126913)
-HSW Applications to not send close DCMD as the first command to perform Firmware update.(DCSG00055146)
-Update/remove Snapdump save count field in show snapdump command based on FW support.(DCSG00038800)
-Include new field cannotSetMode in MR_AUTO_CFG_PARAMETER structure..(DCSG00072780)
-API changes to expose MR_AUTO_CFG_PARAMETER for NONE mode.(DCSG00151058)
-Add new security events.(DCSG00167313)
-Request for DPMstat support in MegaRAID SAS 3.5 controllers in storcli.(DCSG00032273)
-MR API: update field in event structure..(DCSG00093331)
-Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API.(DCSG00226286)
-SMART Polling Improvement- API Changes.(DCSG00214352)
-References to MR_ENCL_LIST and MR_ENCL_LIST_EXT should be based on the support bit.(DCSG00037323)
-Shenandoah: Type 2 Back plane Support for StorCLI.(DCSG00054795)
-StorCLI: Implementing span depth logic and pd per array count for RAID 10.(DCSG00049781)
-Updating BST scripts to support auto BST through VBAS in clear case version 9.(DCSG00050763)
-FW SAS MEGA API:Change MR_EVT_CTRL_FLASH_DISALLOWED_SB_KEY_CHANGE_PENDING event.(DCSG00086780)
-Revert the CLI Help Text for backwards compatibility to include Dimmer Switch 3.(DCSG00068659)
-Shenandoah: Reverting back the changes made for Span setting for RAID 1 & 10.(DCSG00073393)
-New MFI Stat for the updated recon behavior.(DCSG00229416)
-Shenandoah: Remove Span setting for RAID 1 & 10.(DCSG00043198)
-Restore Factory Default doesn't prompt user to reboot the system after being performed.(DCSG00122000)
-MR API changes - Support new Provisional bit in CTRL INFO and new MFI status for Platform Security.(DCSG00106380)
-Add support for signing MegaRAID Legacy BIOS CU Images (CTLR) images.(DCSG00143847)
-Phase 14 : StorCLI should provide power cycle message post erase all command is executed.(DCSG00039542)
-Enhancement of Enclosure MultiPath algorithm in storcli.(DCSG00075191 (Port Of EnhancementRequest DCSG00079538))
-Support to generate storcli static library.(DCSG00075265 (Port Of EnhancementRequest DCSG00075687)
-Updating toolchain for VMware7.0 GA.(DCSG00134764 (Port Of EnhancementRequest DCSG00136269))



007.1212.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------  
MR 7.12

Defects:
StorCLI should refer to MR_PD_INFO.properties.ISECapable to display "Cryptographic Erase Capable" field - Revert of SCG(DCSG00014660)
Making the Predictivefaliure  check OEM specific in controller health algorithm(DCSG00014971)
HBA345_Dev_UT: Enclosure position value in perccli is same for both front and rear BP's(DCSG00033180
Cisco - CSCVr89052 - PATH_1 and PATH_BOTH assigned drives not getting displayed under storcli in WF DDROCK setup(DCSG00050891)
StorCLI Point release RO DCSG00079546 - Windows binaries are missing from the RO(DCSG00081022)
 StorCLI 7.10 point release  - /cx erase help not listing all supported commands(DCSG00081294)
StorCLI 7.10 point release - Update license files to RO DCSG00079546(DCSG00081298)
Removal of unsupported phy commands on IT3 controller(DCSG00025416)
Phase 12 - Oct Huawei DET - New PD FW Not Updated After Flashing PD FW (NVMe)(DCSG00015875)
MR_6.14_Huawei: OnDemand Snapdump in Windows gives failure message "RTTdump Feature not supported"(DCSG00020717)
help is not proper for show events and set copyback commands(DCSG00005503)
MR 7.12: Storcli: Instance Validation Failed for "/call show all" and controller-detailed-properties-schema(DCSG00006331)
MR 7.12: Storcli: Instance Validation Failed for "/call/pall show all" and controller-phyerrorcounters-schema(DCSG00006853)
Orion PA9 : Convention comes in same line while performing help for /c0/e0/s0 download.(DCSG00008084)
MR_7.12_Storcli: Xenserver8: "Core dumped" while executing "/call/eall show all" and "/call/eall/sall show all"(DCSG00009400)
Aero DBU PA7 : Init is in progress error message is thrown by Storcli for start migrate command when VD erase is in pro(DCSG00012344)
Orion PA9 : Storcli version mismatch as compared in storcli -v and storcli properties(DCSG00014485)
Orion PA9 : Storcli crashes while performing storcli /c0 show(DCSG00014486)
Storcli show all cmd displaying "AVAGO" in scheduled tasks info(DCSG00014580)
Aero DBU PA7 : Storcli displays multiple error messages when user enters incorrect device ID during migrate operation.(DCSG00014644)
Fixing Coverity defects - resource leaks and null referencing(DCSG00015721)
Correcting the detailed help syntax(DCSG00016268)
MR7.12 StorCLI: Ouptput message Description wrong for StorCLI VD policy change from WT -WB(DCSG00016372)
StorCLI:  Fixing coverity defects and adding debug statement(DCSG00019683)
perccli windows binary property page has storcli references(DCSG00019800)
Aero DBU Alpha : Storcli displays incorrect error message for "add vd each r0" command when SED drive is connected in t(DCSG00019816)
Application Exit code is always success for UEFI StorCLI(DCSG00020670)
MR 7.12 LSA "instant secure erase" is not found in storcli as cli use secureerase(DCSG00022096)
Help content for Drive Init is not showing it as Clear operation(DCSG00022893)
MR7.12_Storcli: On drive rebuild, there is a mismatch between the pd rebuild state and respective legend(DCSG00022942)
MR 7.12: Storcli: Instance Validation Failed for "/call start Diag Duration=40" and controller-diag-schema(DCSG00023543)
MR 7.12: Storcli: Instance Validation Failed for "/call show linkconfig " and controller-linkconfig-schema(DCSG00023545)
Aero Alpha : Storcli throw Segmentation Fault in Driver load error handing path -(DCSG00024554)
MR 7.12_Storcli: On ARM server the latest storcli Vendor,Licenses,URL and distribution shows as "AVAGO Technologies"(DCSG00025885)
Aero DBU Alpha - Scheduling is displayed as Schedulling under "/cx set pr ? " command description(DCSG00027203)
Add warning/recommendation messages for changing lane speeds(DCSG00027869)
Orion MR : Description for storcli output is not proper after collecting the snapdump with id=all(DCSG00031711)
Aero Alpha: Storcli stops functioning during run of attached script(DCSG00034379)
Storcli returns wrong Operating system in Windows.(DCSG00037088)
MR 7.12_Storcli: The latest storcli vmware build reference URL shows "http://www.lsi.com"(DCSG00039104)
MR 7.12_Storcli: The latest storcli vmware build 007.1209.0000.0000 shows older package version(DCSG00039112)
PERC 11:EKMS:PKG 2973: EKMS Boot Agent Status is not updating properly.(DCSG00049004)
PH13 StorCLI PA - Update help section about 'nolog' option(DCSG00002975)
PH13 PA - StorCLI - Incorrect message for /call/pall show all command(DCSG00003003)
StorCLI_7.12_Ph13:Phyreset Fails on IT controllers(DCSG00005488)
PH13 PA - StorCLI - NVMe drive linkspeed not seen with /cx/pall show(DCSG00009522)
With IT controller for set or reset with invalid phy is not showing error(DCSG00010226)
Aero_storecli:Using latest storecli Firmware product id parameter value fail to display.(DCSG00011446)
MR_7.12: Storcli: Segmentation Fault for "storcli64 page"(DCSG00012563)
Storcli ph13: Fixing array size for function DEBUG_LOG(DCSG00014665)
Aero Orion IT:- Mismatched phy info listed for 440-16e/440-16i(DCSG00023320)
Enclosure position value in storcli is same for both front and rear BP's(DCSG00031302)
Misleading error message when create unmap VD with storcli64.exe /c0 add vd each r0 unmap using unmap and non-unmap PDs(SCGCQ02059720)
StorCLI: Debug prints enabled in latest Phase 12 PA storCLI.efi image(SCGCQ02097317)
Json Schema for the command "storcli /cx/ex show phyerrorcounters" needs to be updated(SCGCQ02101372)
MR 7.11: Storcli: Instance Validation Failed for "/call show all" and system-schema.json(SCGCQ02112192)
DBU Aero PA4 : Cosmetic error is seen in command description for Show SSDThermalPollInterval ?(SCGCQ02124673)
Aero A0 PA4: "Storcli /c# set jbod=on" shows success but does nothing(SCGCQ02117219)
Aero (DBU PA4):Storcli: Junk character in PD start locate command description.(SCGCQ02125654)
Phyreset Fails on IT controllers and update help(SCGCQ02169242)
Drive mode-e fw download with activatenow is not working(SCGCQ02142068)
MR 7.11: Storcli: Instance Validation Failed for "/call/eall show status extended" and enclosure-status-extended-schema.json(SCGCQ02150924)
MR7.11_Storcli: Incorrect error description while creating r1 with single drive(SCGCQ02165933)
Phase 12 - Oct Huawei DET - "./storcli64 /c0/pall show" Command Fails With "Null pointer exception"(SCGCQ02175414)
Phase 16 (IR) - Oct Huawei DET - Unsupported Drive State is Displayed for "./storcli /c0 show" Command(SCGCQ02170389)
MR 7.11 - Oct Huawei DET - Nomenclature Issue for "rbld=Rebuild" In Storcli Show Help Menu for SAS3516(SCGCQ02170197)
Usage of 64 bit address instead of 32bit address while sending commands to FW in uEFI driver less environment(SCGCQ02174934)
MR_7.10_Storcli: Storcli displays incorrect error message for unmap VD creation with regular HDD drives.(SCGCQ02019751)
PH12 PA - StorCLI crashes when call/pall show executed with SAS3 & Ventura boards(SCGCQ02103217)
PH12 PA - StorCLI - Debug StorCLI binary is placed in both places of EFI dir RO SCGCQ02085693(SCGCQ02091140)
PH12 PA - Update readme file in VMwareOP64 folder in accordance with PR SCGCQ01923533(SCGCQ02108550)
MR 7.11: Storcli.efi: In ARM server UEFI shell, storcli.efi hangs forever when storcliconf.ini is present(SCGCQ02115036)
Aero (DBU PA4):Storcli:  VD legend is missing in "/call/vall show expansion" command.(SCGCQ02124508)
Aero DBU PA4 : storclif /cx show configautobalance  ? help output shows the name as "show NCQ"(SCGCQ02124632)
Configuring multiple lane speed is working only for fisrt ID, Rest were ignored(SCGCQ02136333)
Aero (DBU PA5):Storcli: Storcli: "/c0 set patrolread ?" lists detailed help and snapdump rttdump is mentioned as optional.(SCGCQ02140873)
MR 7.11: Storcli: Instance Validation Failed for "/call/eall show status" and enclosure-status-schema.json(SCGCQ02150921)
Aero (DBU PA5):Storcli: Force is not mentioned as key word in "/cx/vx del" error message.(SCGCQ02142017)
MR7.11_Storcli: On drive rebuild, there is a mismatch between the pd rebuild state and respective legend(SCGCQ02165944)
Aero (DBU PA5):Storcli: "Ctrl" legend not mentioned.(SCGCQ02146822)
MR7.11_Storcli: storcli set securitykey detailed help does not show description for all the options(SCGCQ02096732)
MR7.11_Storcli: storcli show output shows UBUnsp as UBad Unsupported where as UGUnsp just Unsupported(SCGCQ02096722)
Aero IT - PA3 - StorCLI crashes for 'storcli J command(SCGCQ02117749)
Lenovo Orion IT:- Command to flash UEFI on Aero/sea HBA from storcli/scrutiny fails(SCGCQ02137751)
Flashing of Completeflash fails on Sea IT controller(SCGCQ02139780)
StorCLI: Fixing coverity defects(SCGCQ02123769)
MR 7.11: Storcli: Instance Validation Failed for /call/show_smartpollinterval.json and controller-smartpollinterval-schema.js(SCGCQ02135516)
DBU PA5 Aero : Background operations keep on progressing after hitting /c0 shutdown from storcli(SCGCQ02132024)
Aero (DBU PA5):Storcli: No "Rbld" legend during rebuild.M(SCGCQ02146819)
complete Lane WWID is not displayed(SCGCQ02145716)
Convention comes in same line while performing help for /c0/e0/s0 download.(SCGCQ02176681)
Adding missing syntax for the command deviceorderbyfirmware(SCGCQ02121705)
MR 7.11: Storcli: Instance Validation Failed for "/call/vall show unmap" and vd-unmap-schema.json.(SCGCQ02113316)
Aero (DBU PA5):Storcli: "completeflash" is listed in Windows help file.(SCGCQ02141931)
Aero (DBU PA5):Storcli: Force option not mentioned in "/cx/dx add mirror" and "/cx/vx start init" command.(SCGCQ02140878)
Force option is needed only for Parallel Drive microcode update, but it allows to take for normal also(SCGCQ02177086)
StorCLI Copyright Notice Needs to be updated(SCGCQ02174040)
Wrong error message when create unmap VD with unmap disable on controller(SCGCQ02064118)
Aero DBU PA4 : storclif /cx delete colinfo  ? shows syntax error(SCGCQ02124492)
MR 7.11: Storcli: Instance Validation Failed for "/call show" and controller-properties-schema.json.(SCGCQ02108770)
PH12 PA - StorCLI version not getting printed for show file command(SCGCQ02105185)
Aero DBU PA4 : Command name shown in help output differs for storclif.efi /cx show limitmaxrateSATA ?(SCGCQ02124667)
Aero DBU PA4 : Redundant information is displayed for set driveactivityled command in storclif.(SCGCQ02124675)
Aero (DBU PA4):Storcli: Wrong reference of "page=[X]" as part of syntax error message.(SCGCQ02124252)
Aero DBU PA4 : storclif.efi /cx show deviceorderbyfirmware ? throws syntax error.(SCGCQ02124528)
MR 7.11: Storcli: Instance Validation Failed for /call/show_consistencycheck.json and controller-cc-schema.json(SCGCQ02135510)
Phase12-Storcli- In Windows storcli64.exe /c0 show htbparams is showing random values for SAS3 controller(SCGCQ02125598)
Aero (DBU PA5):Storcli: No description of patrolread "OFF" and optional is mentioned as {}.(SCGCQ02140859)
PH12 BETA - /cx erase help not listing all commands(SCGCQ02146466)
Aero (DBU PA5):Storcli: No consistency in the usage of "|" in the command such as "on|off".(SCGCQ02142022)
Phase 12 - Oct Huawei DET - Delay Option In PD Download Operation is Not Honored(SCGCQ02176690)
With IT controller for set or reset with invalid phy is not showing error(SCGCQ02181823)
Updating phy link reset logic for IT cards with respect to storelib changes(SCGCQ02184862)
Drives connected to active backplanes not showing the phy info in connector name(SCGCQ02112424)
PH12 PA - StorCLI - 9310-8i IR FW download fails(SCGCQ02121783)
MR 7.11: Storcli.efi: On ARM server, incomplete configuration data received error is observed for any storcli.efi command(SCGCQ02114898)
Aero PA6 - storcli snapdump id=x errors without optional file parameter(SCGCQ02161748)
PH11 - StorCLI - Incorrect message for /call/pall show all command(SCGCQ02169536)
cli does not allow  to do crypto erase on SATA SSD.(SCGCQ02147075)
MR7.11_Storcli: Storcli stop erase needs an help file update(SCGCQ02168895)
Phase 12 - Oct Huawei DET - Incorrect Help Menu For "show phyerrorcounters"(SCGCQ02180495)
Phase 12 - Oct Huawei DET - New PD FW Not Updated After Flashing PD FW (NVMe)(SCGCQ02191421)
Aero PA4 DBU : Storclif doesn't show details for VF/PF in help file for vfmap command .(SCGCQ02123789)
Aero (DBU PA4):Storcli: Typo in /c0 add vd detailed help.(SCGCQ02119091)
Aero (DBU PA4):Storcli: /c0 compare lists /c0/px compare command.(SCGCQ02124246)
StorCLI: Fixing coverity issue in libmod(SCGCQ02123790)
SWR:Storcli: "Show" and "show all" output Description is shown as "No Enclosures found"(SCGCQ02146814)
MR 7.11 storcli -help missing the verbose option(SCGCQ02158600)
Phase 12 - Oct Huawei DET - PD FW Download is failing for Mode f(SCGCQ02168197)
PH12 PA - StorCLI - Incorrect string displayed with show command in FreeBSD 11.2(SCGCQ02094529)
PH12 PA - StorCLI /cx/pall show fails on 9400-8e board(SCGCQ02119004)
MR 7.11: Storcli: Instance Validation Failed for "/call/v5 set bootdrive=off" andcontroller-bootdrive-schema.json.(SCGCQ02115786)
StorCLI: Fixing coverity defects for second run(SCGCQ02125523)
MR 7.11: Storcli: Instance Validation Failed for /call/show_all.json and controller-detailed-properties-schema.json(SCGCQ02135526)
Aero (DBU PA5):Storcli: /c0 set ? lists bbu,mx,px and lnx commands.(SCGCQ02136689)
Aero DBU PA4 : Storclif should not display vendor name in storclif.efi  /cx/ex download help command(SCGCQ02123765)
Aero (DBU PA5):Storcli: Improper spacing for the linkspeed description and "YY" parameter leads to confusion.(SCGCQ02139910)
MR 7.11: Storcli: Instance Validation Failed for /call/show.json and controller-properties-schema.json(SCGCQ02135420)
MR 6.14 - Oct Huawei DET - "Rbld=Rebuild" is Not Available In Storcli Show Help Menu for SAS3108(SCGCQ02170181)
MR 7.11: Storcli: Instance Validation Failed for "/call/cv show all" and cache-vault-detailed-schema.json(SCGCQ02150651)
Aero (DBU PA5):Storcli: Help notes needs an update.(SCGCQ02146823)
Phase 12 - Oct Huawei DET - Incorrect Status for PD FW Download (Ventura IT)(SCGCQ02173203)
Phase 12 - Oct Huawei DET - Incorrect Phy Details Displayed for Ventura IT Controller(SCGCQ02174296)
	
Enchancement:
To bring MR 7.10 storcli change to CC9 GCP database(DCSG00013486)
Support to generate storcli static library(DCSG00075265)
Bring MR 7.11 storcli change to CC9 GCP database(DCSG00014492)
Updating the Makefile and projects as per new CC/CQ changes(DCSG00003002)
Updating the Json Schema files with respect to the latest code(DCSG00007394)
Controller commands Json Schema files update as per the latest code(DCSG00007435)
Schema validation : Schema update for VD/DG/Foreign related commands(DCSG00007453)
Add UEFI Shell StorCLI support for 64-bit Ventura Gen MR Legacy Boot solutions (solutions without UEFI driver)(DCSG00008200)
Changing the CBB download image type as per new MR API(DCSG00010253)
Migrating StorCLI's 64 bit VMware toolchain to 6.8.7-13394445(DCSG00014503)
PERC 11: Provide ability to expose SEP to host and disable PERC SES management in PercCLI / HII(DCSG00015020)
Supporting build and BST process through VBAS in Clear Case version 9(DCSG00024818)
Windows and Linux StorCLI HSM based signing support(DCSG00031618)
StorCLI PH13: Adding interface for lane display and configuration command for IT controllers.(DCSG00007909)
Atlas Support on Aero-IT(DCSG00008038)
Concern for security key passed in from storcli to be read in process data(SCGCQ02066380)
Support FMP Images in UEFI Version of PERCCli(SCGCQ02078649)
Add segment area into pci information of Megaraid controller in Storlib and storcli(SCGCQ02201178)
Create DVT / PVT PnP IDs for Cisco Pismo Beach card(SCGCQ02108965)
Return pended IOCTLS that was not completed after some numbers of OCRs had been initiated.(SCGCQ02066395)
Enable SnapDump for iMR(SCGCQ02208421)
HDET: Support in storCLI support PD firmware download for 3008IR/3008IT controllers(SCGCQ02160016)
multi VSES implementation(SCGCQ02066438)
Return pended IOCTLS that was not completed after some numbers of OCRs had been initiated.(SCGCQ02066399)
Add displaying list of enclosures in controller show and show all command(SCGCQ02124566)
LibMod changes : MR: 64 Bit  Utilities/Application to Support VMWARE ESXi 6.7+(SCGCQ02085102)
SAS 3_5 Ventura family UEFI NVMe drive serial number issue(SCGCQ02074657)
Unmap error message changes as per new description in MR API(SCGCQ02115017)
MR: 64 Bit  Utilities/Application to Support VMWARE ESXi 6.7+(SCGCQ02066386)
Lenovo Whitley/Orion - Addendum 7 - Lenovo request to support StorCLI & LSA for Valvano 28i (MR+Cub) and Custom Form Factor(SCGCQ02082612)


007.1022.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------

Defects :
 - PERCcli Help text is missing description for "Lane Information"(SCGCQ02150899) 
 - Add NVMe width comments to mr.h(SCGCQ02146846) 
 - Fix API changes done for NVMe readiness(SCGCQ02142981) 
 - CLI returns "success" when attempting to set DS3 or DS4 to enabled(SCGCQ02116380) 
 - CLI returns "success" when attempting to change the H840 controler to eHBA personality.(SCGCQ02114332) 
 - CLI returns wrong error code upon failure(SCGCQ02084966) 
 - HPE shenandoah: storcli crashes during show command when DGs present(SCGCQ02065695) 
 - "Run time to empty" field showing as "Battery is not being charged" when the battery is being charged.(SCGCQ02045324) 
 - ROP version not displayed with latest ROP version SCGCQ02035462(SCGCQ02041094) 
 - FW flash fails to load the latest image after upgrade downgrade with resetnow option(SCGCQ02035152) 
 - retentiontest command is successfully triggering BBU test on Shenandoah controller(SCGCQ02021398) 
 - Storclio (007.0911.0000.0000) detailed help file doesn't have " locale " option for flashing FW in Dual/Active & Backup mode.(SCGCQ02012025) 
 - hot spare reference in Add Spare command output(SCGCQ01897463) 
 - Shenandoah:Strocli show all output return failure but generates output(SCGCQ01929191) 
 - Junk message "STR_JBOD_OBJ" is displayed in the output of storcli /c0 show JBOD command.(SCGCQ01932770) 
 - Shenandoah_StorCLI: No legend presend for VD Delete Failure(SCGCQ01936811) 
 - Shenandoah_StorCLI:Setting Unmap=OFF gives success for a LD when unmap is not supported and not enabled on that LD(SCGCQ01940291) 
 - Set WrCache= WB ,says success even though VD is in WT.Proper warning message should be given to the user(SCGCQ01940296) 
 - Legend missing for LD BGI resume/pause commands(SCGCQ01940347) 
 - System hangs while creating VD in EFI shell.(SCGCQ01945551) 
 - Shenandoah_StorCLI: Storcli crashes on checking LD preserved cache info(SCGCQ01955069) 
 - CLI is showing the incorrect OS version(SCGCQ01956276) 
 - Unified StorCLI : Add extra space to CBB header(SCGCQ01956678) 
 - PH10 Alpha - StorCLI throws "0 Failed 32782 Failed to get PD Info" when /c0 show executed in EFI(SCGCQ01960322) 
 - JBOD list is not showing in order when using /cx show(SCGCQ01961527) 
 - supported personalities has blank value(SCGCQ01965370) 
 - storcli faults for enclosure show command(SCGCQ01985815) 
 - MR7.10_PA1: Storcli binaries for RHEL/SLES OS is not present for ARM(SCGCQ02006374) 
 - NVMe drive displays incorrect information with IT card(SCGCQ02009852) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set personality" JSON output.(SCGCQ02016762) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for snapdump commands.(SCGCQ02018073) 
 - MR_7.10_Storcli: No schema file for controller sesmultipathcfg commands.(SCGCQ02018134) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for drive jbod commands.(SCGCQ02018135) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for "/cx get vpd" commands.(SCGCQ02018140) 
 - MR_7.10_Storcli: Instance Validation Failed between "virtual-drive-detailed-schema.json" and "/call/vall show all "(SCGCQ02018333) 
 - MR_7.10_Storcli: bbu-show-modes-schema.json file is not in JSON format.(SCGCQ02019740) 
 - Instance Validation Failed between " controller-lane-show-schema.json" and "/call/lnall show"(SCGCQ02019746) 
 - Pending Image details are not populated after FW upgrade and downgrade.(SCGCQ02024065) 
 - Instance Validation Failed between "controller-detailed-properties-schema.json" and "/call show all "(SCGCQ02032911) 
 - MR_7.10_Storcli: Add VD command output is not in JSON format.(SCGCQ02034493) 
 - Instance Validation Failed between "vd-unmap-schema.json" and "/call/vall show unmap"(SCGCQ02035370) 
 - remove the maxconcurrentpd check from storcli and report fw returned failure(SCGCQ02053910) 
 - Storcli: "resume migrate" command does not show syntax error.(SCGCQ02061340) 
 - Instance Validation Failed between "controller-detailed-properties-schema.json" and "show_all"(SCGCQ02062957) 
 - Show Snapdump help command lists delete snapdump details as well.(SCGCQ02064836) 
 - Storcli: "show config" command shown as Un-supported.(SCGCQ02064839) 
 - PH11 Alpha - StorCLI 'show file' command throws segmentation fault for complete flash image in FreeBSD(SCGCQ02065691) 
 - Storcli: No schema files for htbparams commands.(SCGCQ02065698) 
 - "Delete snapdump" command shows same description "Snapdump clear" for success and failure case.(SCGCQ02065734) 
 - Incorrect error message displayed while creating R10 VD when no free space available.(SCGCQ02067575) 
 - Schema file updates for controller show all output change for defect SCGCQ02048150(SCGCQ02069817) 
 - Typo in storcli /c0 set linkspeed help(SCGCQ02070951) 
 - Aero (DBU PA2): Storcli: No syntax error displayed for "storcli mronly" command.(SCGCQ02072746) 
 - Wide port info is not displayed under connector name for Backplane attached drives.(SCGCQ02076923) 
 - Empty data is listed when we query for show linkconfig(SCGCQ02076931) 
 - htbparams help output needs update.(SCGCQ02077156) 
 - show/set lane speed shows success when we are in SAS profile(SCGCQ02078437) 
 - Libmods: show.set lane speed shows success with wrong data when we are in SAS profile(SCGCQ02078513) 
 - Recon command (./storcli /cx set recon) is throwing syntax error.(SCGCQ02081415) 
 - storcli /c0/ex/s23,24 show patrol read doesnt not show error for slot 24 (Invalid Slot)(SCGCQ02082142) 
 - Aero (DBU PA2): Storcli show detailed help does not list "show all " command.(SCGCQ02082303) 
 - Aero (DBU PA2): Storcli: Get rttdump detailed help shows syntax error.(SCGCQ02082460) 
 - Storcli: Incorrect message while executing "storcli64.exe /c0/v0 del discardcache"(SCGCQ02083828) 
 - Failure status for /call/sall and /call/eall/sall command.(SCGCQ02084549) 
 - Storcli: Error in /c0/f0 command output.(SCGCQ02089892) 
 - StorCLI listing PD Slot Status as "Incorrect Status Value" for configured PD's(SCGCQ02090770) 
 - Storcli doesn't exit with controller status message after doing OFU.(SCGCQ02091548) 
 - Libmod changes for SCGCQ02090770	(SCGCQ02096774) 
 - Aero (DBU PA3): Storcli: FW hits Megamon while executing storcli in EFI shell when EFI Driver is unloaded.(SCGCQ02097647) 
 - StorCLI crashes for 'storcli J command(SCGCQ02117749) 
 - Storcli: VD legend is missing in "/call/vall show expansion" command.(SCGCQ02124508) 
 - Controller Health Status not consisten across applications(SCGCQ02182243) 
 - Perccli does not enable Power Save mode for UG & HS type 1 & type 2.	(SCGCQ02125408) 
 - StorCLI: Delete config failure message need correction(SCGCQ02086726) 
 - StorCLI:VD reference in Delete preserved cahce command output -Branding(SCGCQ02083992) 
 - VD reference in set JBOD command output message(SCGCQ02078507) 
 - storclif.exe /c0/ex/sx show poh should show proper message during command execution.(SCGCQ02075242) 
 - STORCLI: Show command output having wrong legend for Slt for oem Hercules(SCGCQ02067616) 
 - Grammatical error in Perccli message(SCGCQ02065513) 
 - BSOD observed when VD/JBOD Creation/Del and snapdump Cycles are initiated.(SCGCQ02045967) 
 - VD legend missing in the legend for Foreign config show all output(SCGCQ02016798) 
 - Hercules:Shenandoah:Transformation is coming as Reconstruction , while migrating the Raid 1 to Raid 5 .(SCGCQ01897468) 
 - Mis-spelled words in StorCli's Help(SCGCQ01898853) 
 - Hot spare reference in storcli.exe /cx/ex/sx show all command output(SCGCQ01905019) 
 - Reference to VD in storcli.exe /c1/jbodall delete command output(SCGCQ01905077) 
 - Fixing coverity issues Removing dead code and Out of bound access(SCGCQ01924504) 
 - Shenandoah_StorCLI: HotSpare reference in Add VD Command output(SCGCQ01936887) 
 - storcli /c0 show events output not listing the Event ID's(SCGCQ01940290) 
 - Shenandoah_StorCLI:Hot spare reference in storcli64 /cx show/set restorehotspare command outputs(SCGCQ01940437) 
 - Shenandoah_StorcLI:Drive Group reference in Add dedicated spared drive command in CLI(SCGCQ01955167) 
 - Intel NVMe drive "Model Number" displayed incorrect under Device Attributes(SCGCQ01957949) 
 - Aero: Segmentation Fault in storcli /c0 show all(SCGCQ01996444) 
 - Storcli throws an 'Incomplete foreign configuration' error when there is no enclosure connected(SCGCQ02006450) 
 - storcli gives error when the lane configuration is set as X8	(SCGCQ02007152) 
 - MR_7.10_Storcli: No schema file for controller unmap commands(SCGCQ02016749) 
 - MR_7.10_Storcli: Instance Validation Failed "controller-restorehotspareoninsertion-schema" and "set restorehotspare"(SCGCQ02016765) 
 - MR_7.10_Storcli: Instance Validation Failed "controller-properties-schema" and "/c0 show"(SCGCQ02016768) 
 - MR_7.10_Storcli: controller-detailed-properties-schema.json or "/call show all " output not in JSON format(SCGCQ02016771) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-autoconfig-schema.json" and "show autoconfig" JSON output.(SCGCQ02018227) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" JSON output.(SCGCQ02018277) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON output.(SCGCQ02018305) 
 - MR_7.10_Storcli: Instance Validation Failed between "system-schema.json" and "./storcli show" and "show all" JSON output.(SCGCQ02018313) 
 - MR_7.10_Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/eall/sall show all"(SCGCQ02018327) 
 - MR_7.10_Storcli: Instance Validation Failed between "cache-vault-detailed-schema.json" and "/call/cv show all "(SCGCQ02019729) 
 - Storcli displays drive state as UBad instead of UBad (unsupported)(SCGCQ02031615) 
 - Instance Validation Failed between "drive-group-hidden-schema" and "/c1/dall set hidden" & "set security"(SCGCQ02040779) 
 - Fixing coverity issues Fixing resource leaks(SCGCQ02043601) 
 - Storcli help file should show the expand size format.(SCGCQ02047109) 
 - Updating the storcli schema mapping document	(SCGCQ02050586) 
 - PH11 Alpha - StorCLI - Parse error observed for command 'StorCLI J' while validating Jason(SCGCQ02053030) 
 - JSON-SCHEMA : IT-Controller Json-schema validation erros in MR_SAS_Unified_StorCLI_7.10(SCGCQ02053914) 
 - Aero: Storcli : Storcli crashed when Firmware upgrade tried on Sea controller(SCGCQ02060276) 
 - Aero (DBU PA2): Storcli: JSON readme file does not have complete VD and PD support list.(SCGCQ02061328) 
 - Instance Validation Failed bw "enclosure-drive-detailed-schema.json" & "/call/eall/sall show all"(SCGCQ02062958) 
 - PH11 Alpha - StorCLI - Compare linkspeed command failed for 6Gbps link(SCGCQ02063932) 
 - Invalid aero controllers are not displayed with apt message in driver less mode(SCGCQ02065581) 
 - Storcli connector display not matching with Aero board 9560-16i.(SCGCQ02072448) 
 - Aero (DBU PA2): Storcli: /cx/mx command does not mention about "Auto" settings.(SCGCQ02082208) 
 - Storcli: Force is mentioned as optional in snapdump delete command.	(SCGCQ02083822) 
 - Help of /cx/px compare command needs update and /cx/px reset ? shows syntax error.(SCGCQ02084752) 
 - No proper legends in /fall output.(SCGCQ02100491) 
 - Aero (DBU PA3): Storcli: Incorrect schema mapping for "/cx set autoconfig " command.(SCGCQ02101558) 
 - Storcli: OCR helps needs update.(SCGCQ02113241) 
 - Storcli: No proper description of set and show sesmultipathcfg.(SCGCQ02113358) 
 - StorCLI: File sync issue with rel and dev stream for MR 7.10	(SCGCQ02116806) 
 - Storcli script stops with error "can't fork: Cannot allocate memory"	(SCGCQ02184427) 
 - IT- CLI treats EID and Partner Device ID as two different enclosure during pd info command and fails.(SCGCQ02185442) 
 - "/eall show" will not show enclosure details if it is in multitpath & no drives connected.(SCGCQ02186022) 
 - Legacy messages present with create and rekey of securitykey on controller(SCGCQ01581843) 
 - Shenandoah_StorCLI:VD reference in CLI outout for Firmware update command failure case(SCGCQ02083991) 
 - StorCLI: VD listing for c0 show and vall show is toggled	(SCGCQ02078936) 
 - output information for link configuration is displayed incorrectly(SCGCQ02073046) 
 - Drive Groups is shown instead of arrays in show all command(SCGCQ02048660) 
 - Help is not updated for get snapdump without ID option.(SCGCQ02046991) 
 - StorcliO show oob command fails for Invader based cards(SCGCQ02040783) 
 - Adding debug logs to Mfi files(SCGCQ01891583) 
 - MR7.8_Storcli: Storcli fails to install on ARM server with Missing Maintainer message(SCGCQ01919830) 
 - StorCLI show SAS address for NVMe drives	(SCGCQ01921258) 
 - Unified StorCLI 7.9 : Fixing coverity issues - Dead code,resource leaks,and memory corruption - Part 1(SCGCQ01925503) 
 - Incorrect help option for set autoconfig in StorCli's Help(SCGCQ01932035) 
 - Unmap enabled property is shown in VD detailed properties when controller does not support unmap	(SCGCQ01932177) 
 - Unified StorCLI - Aero : "FullFlashImage" environmental variable component stamp change(SCGCQ01963738) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for /cx/px commands.(SCGCQ02018137) 
 - MR_7.10_Storcli: Instance Validation Failed between "enclosure-schema.json" and "/call/eall show" JSON output.(SCGCQ02018322) 
 - MR_7.10_Storcli: Instance Validation Failed between "foreign-configuration-schema.json" and "/call/fall show"(SCGCQ02024327) 
 - Aero UTP: storclif /call show commands output contains "Count 4 exceeded for token id #"	(SCGCQ02034064) 
 - Aero IT - PA1 - StorCLI - BIOS verion not displayed with flash file using 'show file' command(SCGCQ02034490) 
 - failure in StorCLI enclosure show status	(SCGCQ02040640) 
 - unmap attribute is not mentioned in help file command "add vd each r0".(SCGCQ02042106) 
 - Incorrect status displayed for pause rebuild command.(SCGCQ02043610) 
 - PH11 PA - StorCLI - Segmentation fault seen when 'compare linkspeed' executed on Fury C0 board(SCGCQ02044777) 
 - Port information is not displayed for Vses Backplane(SCGCQ02053070) 
 - "c0 delete ?" does not list snapdump command.(SCGCQ02053639) 
 - Incorrect status displayed for resume copyback command.(SCGCQ02062834) 
 - Aero (DBU PA2): Storcli: Instance Validation Failed bw "vd-operations-migrate-schema.json" & "start_migrate"(SCGCQ02062960) 
 - Aero (DBU PA2): Storcli: Result shows blank for "resume patrolread" failure case.(SCGCQ02064795) 
 - Fail to set the linkconfig .	(SCGCQ02070797) 
 - Storcli /c2 set linkconfig conname=c0,c1 configid=14 returns invalid syntax error(SCGCQ02070953) 
 - Aero DBU PA2 : Syntax error is seen in storcli /cx(x|all	(SCGCQ02077085) 
 - Aero (DBU PA2): Storcli: Syntax error for "/c0 download psoc/efibios/cpld/fcode ?" download commands.(SCGCQ02077175) 
 - Storcli throws different error messages for show status command in Ventura and Aero(SCGCQ02078409) 
 - Incorrect string displayed in show command in FreeBSD OS(SCGCQ02082949) 
 - MR_7.10_Storcli: "storcli show file=filepath" command shows failure status.(SCGCQ02085630) 
 - PCI Linkconfig configid status is failure, even though it was set(SCGCQ02086669) 
 - Storecli_Aero: Using latest storecli show file command "Aero-DVT -HBA 9500-16e" board output version number shows wrong.(SCGCQ02089427) 
 - Libmods changes for defect SCGCQ02062957(SCGCQ02089862) 
 - Help update for "add vd cachevd" command as Normal VD is created with failure status.(SCGCQ02091155) 
 - Preserved cache help file shows a mismatch in command and the convention.(SCGCQ02106218) 
 - Aero DBU PA4 : Storcli doesn't show the convention details properly for storclio /cx/px show command(SCGCQ02113377) 
 - Aero (DBU PA4):Storcli: Syntax error for /c0 show AliLog ?(SCGCQ02113506) 
 - Aero (DBU PA4):Storcli: Typo in /c0 add vd detailed help.(SCGCQ02119091) 
 - Misleading error msg "157 Failed Cannot mix unmap and non-unmap physical drives in same array"(SCGCQ02151484) 
 - Cryptographic erase field is shown "yes" but crypto erase fails.(SCGCQ02175346) 
 - Device Type for non-UBM backplanes are being shown as Enclosure instead of Backplane(SCGCQ02101095) 
 - Multiple status messages are displayed in the output	(SCGCQ02073042) 
 - Controller health status is shown as optimal when megacell cable is disconnected.(SCGCQ02021393) 
 - Storcli, should fail the command "get snapdump id=0 file=snapdump.zip norttdump"(SCGCQ01889700) 
 - Shenandoah_StorCLI:32 Binary crashes on giving invalid input to the command storcli.exe /c0/jbod0 show(SCGCQ01905831) 
 - For NVMe drive use the term NVMe instead of PCIe(SCGCQ01923119) 
 - PD show all command displays SSD weargauge details , which is not required.(SCGCQ01927864) 
 - MR_7.10_Storcli: Junk character in error message while creating SED vd with regular HDD drives.(SCGCQ02016701) 
 - MR_7.10_Storcli: Incorrect command syntax mentioned in Schema_mapping_list.xlsx file for "/cx set autoconfig" command.(SCGCQ02018097) 
 - Instance Validation Failed between "vd-operations-bgi-schema.json" and "/call/v1 show bgi " and "show init".(SCGCQ02035551) 
 - Storcli shows incorrect output for delete events command(SCGCQ02045816) 
 - BreakMirror RAID Support coming as Yes, even when Breakmirror is not supported(SCGCQ02048150) 
 - Spell mistake on support ondemand snapdump property of show all output(SCGCQ02053923) 
 - StorCLI displays expansion as successful even when there is no free space to expand(SCGCQ02057361) 
 - Instance Validation Failed between "controller-patrolread-schema.json" and "/call resume patrolread"(SCGCQ02062942) 
 - PH11 Alpha - StorCLI - 'show file' command displays incorrect message after reading uploaded bios file(SCGCQ02063689) 
 - Need a space between atleast with StorCLI error message "Unmap is not supported atleast on one device"(SCGCQ02064120) 
 - Storcli:"resource already in use" error message displayed when trying to create VD with one UG and one UBUnsp.(SCGCQ02064828) 
 - Aero (DBU PA2): Storcli: Inconsistency in "add vd" command syntax.(SCGCQ02082196) 
 - Details are displayed twice in "/cx/bbu start ? "(SCGCQ02100905) 
 - Storcli: set termlog shows [=on|off] mentioned as optional.(SCGCQ02113353) 
 - CLI is missing the JBOD PD size for SysPDs when using the "show jbod" command(SCGCQ02132277) 
 - Percli returns “invalid arguments" when trying to create a VD using some PDs already configured in a VD and some U(SCGCQ02122169) 
 - Topology information missing from Storcli output(SCGCQ02048612) 
 -	(SCGCQ02040597) 
 - Unified StorCLI: StorCLI does not return the return code from SLIT/SLIR3 to explorer/command processors(SCGCQ01925156) 
 - Virtual drive reference in Delete Preserved cache command output(SCGCQ01940333) 
 - Storcli not working on large config setup when some of the drives are missing or the system has foreign config.(SCGCQ01940805) 
 - Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01948579) 
 - Shenandoah : Firmware receives incorrect erase type for sanitize crypto erase option(SCGCQ01958564) 
 - Storcli shows BBU present instead of EnergyPAck in HWcfg for StorCLI /cx show all output.(SCGCQ01985592) 
 - Aero:Storcli: Adaptertype shown as UNKNOWN(X0) for Sea (3816_Eval) IT Controller(SCGCQ02008219) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for errorcounters commands.(SCGCQ02018078) 
 - Storcli reported "Boot Volume Supported = NO" eventhough ctrl boot with OS on vd.(SCGCQ02030652) 
 - There is no error message for smart drive failure command.(SCGCQ02040645) 
 - Storcli help file doesn't show recon rate command instead it shows migrate rate.(SCGCQ02046036) 
 - JSON Schema : Updating the schema list with Virtual drive command set(SCGCQ02057360) 
 - storecli_Aero:In linux error message observed in the show output.(SCGCQ02057699) 
 - Checking in JSON schemas(SCGCQ02061305) 
 - Junck character displayed in Virtual SES phy id, when we query phyerror counter for enclosure.(SCGCQ02094970) 
 - Aero (DBU PA3):Storcli: Help of /cx/px reset does not mention about option hard reset.(SCGCQ02100896) 
 - BBU show detailed help does not list "show learn " command.(SCGCQ02100915) 
 - Storcli: Instance Validation Fails for all /call/e65/sall commands where "e65 is not found".(SCGCQ02101564) 
 - Storcli: Remove Nytro supported options in "/cx [start] flush|flushcache [cachecade | ALL]" help.(SCGCQ02113484) 
 - MR7.10 cli return mesg. typo after ctrl restart then immediately running storcli64 /c0 show.(SCGCQ02113833) 
 - Storcli: /c0 compare help lists /c0/px compare command.(SCGCQ02124246) 
 - Serial number not displayed fully in 7.10 StorCLI 007.1017.0000.0000 for IT Controller(SCGCQ02173789) 
 - Hide BBU details from the command "storcli /c0 show alilog" for HPE(SCGCQ01937259) 
 - Disk group is displayed instead of array on HPE platforms(SCGCQ01965366) 
 - MR_7.10_Storcli: unmap attribute is not mentioned in "/c0 add vd" command syntax in Schema_mapping_list.xlsx file.(SCGCQ02016758) 
 - Storcli pop-up a message "controller not found" during chip reset , rather than controller busy.(SCGCQ02024740) 
 - "Invalid RAID level" error message while creating R10 VD.(SCGCQ02034471) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-patrolread-schema.json" and "/call pause patrolread"(SCGCQ02035437) 
 - Instance Validation Failed for "/call show and /call show all".(SCGCQ02101432) 
 - Instance Validation Failed bw "drive-group-detailed-schema.json" and "/call/dall show all".(SCGCQ02101513) 
 - Autoconfig options are allowed to set with latest storcli(SCGCQ02053643) 
 - Unified StorCLI Phase 10 : Image checksum should not be performed for aero images(SCGCQ01942200) 
 - Aero DBU PA1:Storcli: Instance Validation Failed "controller-properties-schema" and "/call show" command.(SCGCQ02035439) 
 - Fixing coverity issues Fixing resource leaks and explicit NULL dereferencings(SCGCQ02042242) 
 - Unified StorCLI : Fixing resource leaks - Part 1(SCGCQ02042513) 
 - Updating Schema mapping doc and fixing validation errors	(SCGCQ02057434) 
 - Storcli: Instance Validation Fails for vd-bootdrive-schema.json and vd-unmap-schema.json.(SCGCQ02101568) 
 - Aero_storecli:Using latest storecli firmware download fail with noreset option.(SCGCQ02101570) 
 - Aero DBU PA4 : Syntax error is seen for the command - storclio.efi /cx/px set state ?(SCGCQ02113123) 
 - PD info incorrectly shows Number of Blocks for >TB drives(>3TB in my case(SCGCQ02183653) 
 - CLI is returning "success" when attempting to set bios mode to Ignore Errors.(SCGCQ02121017) 
 - On Demand SnapDump does not show proper time stamp.(SCGCQ02084833) 
 - Storcli issuing 'add jbod drives=all' causes storcli to crash(SCGCQ01892288) 
 - Initialize the MFG structure(SCGCQ01901166) 
 - Aero:Storcli: Adaptertype shown as UNKNOWN(X0) for Aero (3916_Eval) IT Controller(SCGCQ02021194) 
 - Instance Validation Failed between "drive-group-schema.json" and "/call/dall show " and /call/dall show all(SCGCQ02040756) 
 - PH11 PA Storcli: Incorrect error message shown while programming invalid sasaddress(SCGCQ02042296) 
 - Unified StorCLI : Individual SL_INIT_LIB calls are made for every SL command invocation(SCGCQ02047100) 
 - Updating storcli-cmd-list.xlsx for Drives(SCGCQ02056199) 
 - Message with Incorrect controller object is displayed while setting SSD Caching on VD(SCGCQ02057085) 
 - Storcli displays grammatically incorrect message in detailed help file.(SCGCQ02097641) 
 - MR_7.10: Storcli: Property is shown as SCSI Umap instead of SCSI Unmap.(SCGCQ02101572) 
 - Storcli: /c0 show detailed command does not list /cx/px show phyerrorcounters and /cx show vpd.(SCGCQ02113262) 
 - Aero (DBU PA4):Storcli: Incorrect description of "/c0/v0 show migrate" command.(SCGCQ02113511) 
 - Wrong reference of "page=[X]" as part of syntax error message.(SCGCQ02124252) 
 - Storcli: Junk character in PD start locate command description.(SCGCQ02125654)
 - Storcli doesn't exit with controller status message after doing OFU.	(SCGCQ02101069 port of SCGCQ02091548) 
 - perccli /c0 show all lists topology without any DG's present	(SCGCQ02085925 port of SCGCQ01998332) 
 - MR_7.10_Storcli: bbu-show-modes-schema.json file is not in JSON format.(SCGCQ02079618 port of SCGCQ02019740) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for drive jbod commands.(SCGCQ02079592 port of SCGCQ02018135) 
 - Libmods: HPE serial number display(SCGCQ02062634 port of SCGCQ01885657) 
 - Aero DBU PA1:Storcli: Instance Validation Failed "controller-properties-schema" and "/call show" command.(SCGCQ02061387 port of SCGCQ02035439) 
 - MR_7.10_Storcli: unmap attribute is not mentioned in "/c0 add vd" command syntax in Schema_mapping_list.xlsx file.(SCGCQ02050535 port of SCGCQ02016758) 
 - MR_7.10_Storcli: Instance Validation Failed between "virtual-drive-detailed-schema.json" and "/call/vall show all "(SCGCQ02050471 port of SCGCQ02018333) 
 - failure in StorCLI enclosure show status	(SCGCQ02043616 port of SCGCQ02040640) 
 - Expander FW download using storecli utility crashs.(SCGCQ01979616 port of SCGCQ01979599) 
 - Hide "set pdfaileventoptions" command from CLI Help(SCGCQ01892551 port of SCGCQ01880722) 
 - Error message when Maximum number of VDs are reached	(SCGCQ01911777 port of SCGCQ01856544) 
 - Adding CLI command to display/toggle new controller property.(SCGCQ01927583 port of SCGCQ01106982) 
 - System hangs while creating VD in EFI shell.(SCGCQ01945574 port of SCGCQ01945551) 
 - storclio command not working to update FW on SATA disk(SCGCQ01963953 port of SCGCQ01918814) 
 - Storcli is not showing foreign configs if user has SED drive which is in foreign(SCGCQ01963954 port of SCGCQ01937410) 
 - Restricting PD FW download enable command to FW for SATA drives(SCGCQ01964173 port of SCGCQ01955389) 
 - Add security-related compilation and linker flags to StorCLI - Linux	(SCGCQ01966163 port of SCGCQ01892560) 
 - Unified StorCLI : Enclosure devices are part of drive list used for drive operations	(SCGCQ01982925 port of SCGCQ01979483) 
 - Unified LibMod changes : Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01985486 port of SCGCQ01893074) 
 - Enable iMR advanced debug dump(SCGCQ02035300 port of SCGCQ01873124) 
 - Drive Size Display Miss Match In Storcli Show Output	(SCGCQ02074659 port of SCGCQ02072353) 
 - HDET:Libmods-Boot device should be presented as /dev/sda in Linux operating system during installation and post installation	(SCGCQ02082198 port of SCGCQ02046182) 
 - HDET: Boot device should be presented as /dev/sda in Linux operating system during installation and post installation(SCGCQ02082199 port of SCGCQ02016712) 
 - BSOD observed when VD/JBOD Creation/Del and snapdump Cycles are initiated.(SCGCQ02085669 port of SCGCQ02045967) 
 - storclif /cx delete colinfo ? shows syntax error	(SCGCQ02124654 port of SCGCQ02124492) 
 - PH12 PA - StorCLI /cx/pall show fails on 9400-8e board(SCGCQ02128167 port of SCGCQ02119004) 
 - Storcli: Force option not mentioned in "/cx/dx add mirror" and "/cx/vx start init" command.(SCGCQ02142248 port of SCGCQ02140878) 
 - Aero (DBU PA5):Storcli: No description of patrolread "OFF" and optional is mentioned as {}.(SCGCQ02145876 port of SCGCQ02140859) 
 - PERCCLI to support creation of VD with WB policy for PERC8 MR(SCGCQ01892550 port of SCGCQ01891650) 
 - MR: 64 Bit Utilities/Application to Support VMWARE ESXi 6.7+	(SCGCQ02139866 port of SCGCQ02066386) 
 - Libmod changes for SCGCQ02090770(SCGCQ02097658 port of SCGCQ02090770) 
 - Wide port info is not displayed under connector name for Backplane attached drives.(SCGCQ02085666 port of SCGCQ02076923) 
 - CLI returns wrong error code upon failure(SCGCQ02085528 port of SCGCQ02084966) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON output.(SCGCQ02079591 port of SCGCQ02018305) 
 - Storcli displays drive state as UBad instead of UBad (unsupported(SCGCQ02079521 port of SCGCQ02031615) 
 - Storcli: "resume migrate" command does not show syntax error.(SCGCQ02075292 port of SCGCQ02061340) 
 - BreakMirror RAID Support coming as Yes, even when Breakmirror is not supported(SCGCQ02075281 port of SCGCQ02048150) 
 - Drive Size Display Miss Match In Storcli Show Output	(SCGCQ02075280 port of SCGCQ02072353) 
 - Typo in storcli /c0 set linkspeed help(SCGCQ02074664 port of SCGCQ02070951) 
 - PH11 Alpha - StorCLI - 'show file' command displays incorrect message after reading uploaded bios file(SCGCQ02064703 port of SCGCQ02063689) 
 - Storcli reported "Boot Volume Supported = NO" eventhough ctrl boot with OS on vd.(SCGCQ02047809 port of SCGCQ02030652) 
 - Storcli help file doesn't show recon rate command instead it shows migrate rate.	(SCGCQ02047747 port of SCGCQ02046036) 
 - Storcli shows incorrect output for delete events command(SCGCQ02046875 port of SCGCQ02045816) 
 - Unified StorCLI : Enclosure devices are part of drive list used for drive operations	(SCGCQ01979535 port of SCGCQ01979483) 
 - enhance warning message for personality switch indicating interruption could cause controller to be unstable(SCGCQ01892552 port of SCGCQ01892549) 
 - Storcli, should fail the command "get snapdump id=0 file=snapdump.zip norttdump"	(SCGCQ01906745 port of SCGCQ01889700) 
 - StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911831 port of SCGCQ01886637) 
 - 6.13_SDS : Wrong error message is displayed on trying to create R0 vd on an pre configured drive as EPD.(SCGCQ01925211 port of SCGCQ01196785) 
 - Square bracket is missing in the syntax of "set hardware device page" in storclio.(SCGCQ01929137 port of SCGCQ01224857) 
 - For NVMe drive use the term NVMe instead of PCIe	(SCGCQ01963960 port of SCGCQ01923119) 
 - StorCLI show SAS address for NVMe drives	(SCGCQ01963964 port of SCGCQ01921258) 
 - JBOD list is not showing in order when using /cx show(SCGCQ01965193 port of SCGCQ01961527) 
 - Added Windows compiler security flags (SDL and control flow guard(SCGCQ01965209 port of SCGCQ01949495) 
 - supported personalities has blank value	(SCGCQ01971366 port of SCGCQ01965370) 
 - Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01977028 port of SCGCQ01948579) 
 - Expander FW download using storecli utility crashs.(SCGCQ01979617 port of SCGCQ01979599) 
 - WBSup abbreviation defined twice when running perccli /cX show profile(SCGCQ01995022 port of SCGCQ01993282) 
 - spell mistake in start diag operation failure(SCGCQ01998963 port of SCGCQ01998330) 
 - Proper message to be given on VD creation with wb option while Battery not connected/Failed(SCGCQ02028787 port of SCGCQ01972504) 
 - iMR Changing profileid's using cli results in Status=Success Description=None(SCGCQ02028810 port of SCGCQ02008676) 
 - Enable iMR advanced debug dump(SCGCQ02035289 port of SCGCQ02030908) 
 - On Demand SnapDump does not show proper time stamp.(SCGCQ02085609 port of SCGCQ02084833) 
 - Flashing of Completeflash fails on Sea IT controller(SCGCQ02139848 port of SCGCQ02139780) 
 - Storcli: "Ctrl" legend not mentioned.(SCGCQ02150640 port of SCGCQ02146822) 
 - storcli -help missing the verbose option	(SCGCQ02160908 port of SCGCQ02158600) 
 - MR7.11_Storcli: Incorrect error description while creating r1 with single drive(SCGCQ02168183 port of SCGCQ02165933) 
 - Phase 12 - Oct Huawei DET - Incorrect Phy Details Displayed for Ventura IT Controller(SCGCQ02179296 port of SCGCQ02174296) 
 - Incorrect Help Menu For "show phyerrorcounters"(SCGCQ02180519 port of SCGCQ02180495) 
 - Recon command (./storcli /cx set recon(SCGCQ02086570 port of SCGCQ02081415) 
 - Need a space between atleast with StorCLI error message "Unmap is not supported atleast on one device"(SCGCQ02075290 port of SCGCQ02064120) 
 - Show Snapdump help command lists delete snapdump details as well.(SCGCQ02075287 port of SCGCQ02064836) 
 - iMR Changing profileid's using cli results in Status=Success Description=None(SCGCQ02056156 port of SCGCQ02008676) 
 - Spell mistake on support ondemand snapdump property of show all output(SCGCQ02053926 port of SCGCQ02053923) 
 - Unified StorCLI : Individual SL_INIT_LIB calls are made for every SL command invocation(SCGCQ02047893 port of SCGCQ02047100) 
 - Instance Validation Failed between "drive-group-hidden-schema" and "/c1/dall set hidden" & "set security"(SCGCQ02047136 port of SCGCQ02040779) 
 - unmap attribute is not mentioned in help file command "add vd each r0".(SCGCQ02047095 port of SCGCQ02042106) 
 - Storcli pop-up a message "controller not found" during chip reset , rather than controller busy.	(SCGCQ02047079 port of SCGCQ02024740) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ02009900 port of SCGCQ01761309) 
 - storcli faults for enclosure show command(SCGCQ01986423 port of SCGCQ01985815) 
 - storclio command not working to update FW on SATA disk(SCGCQ01922919 port of SCGCQ01918814) 
 - Restricting PD FW download enable command to FW for SATA drives(SCGCQ01964153 port of SCGCQ01955389) 
 - StorCLI crashes, while trying to enable security on any DG ,incase, when no DG exists(SCGCQ01965185 port of SCGCQ01413253) 
 - Added Windows compiler security flags (SDL and control flow guard(SCGCQ01965210 port of SCGCQ01949503) 
 - Unified LibMod changes : Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01966261 port of SCGCQ01893074) 
 - Add security-related compilation and linker flags to StorCLI - Linux	(SCGCQ01985558 port of SCGCQ01892560) 
 - Snapdump unsupported commands for HPE needs to be disabled(SCGCQ01996375 port of SCGCQ01985589) 
 - MR_7.9: Storcli reported unknown OS for Windows 10 RS5 LTSC.(SCGCQ02009848 port of SCGCQ01992461) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ02011417 port of SCGCQ01761309) 
 - StorcliO show oob command fails for Invader based cards(SCGCQ02043788 port of SCGCQ02040783) 
 - Storclif doesn't show details for VF/PF in help file for vfmap command .(SCGCQ02124488 port of SCGCQ02123789) 
 - Storcli: "completeflash" is listed in Windows help file.(SCGCQ02145743 port of SCGCQ02141931) 
 - Storcli: /c0 set ? lists bbu,mx,px and lnx commands.	(SCGCQ02145756 port of SCGCQ02136689) 
 - Configuring multiple lane speed is working only for fisrt ID, Rest were ignored(SCGCQ02145764 port of SCGCQ02136333) 
 - Help note 'page=[x]' needs update(SCGCQ02149062 port of SCGCQ02146823) 
 - Instance Validation Failed for "/call/eall show status extended" and enclosure-status-extended-schema.json(SCGCQ02153948 port of SCGCQ02150924) 
 - Instance Validation Failed for /call/show_all.json and controller-detailed-properties-schema.json(SCGCQ02154721 port of SCGCQ02135526) 
 - StorCLI listing PD Slot Status as "Incorrect Status Value" for configured PD's(SCGCQ02097676 port of SCGCQ02090770) 
 - Aero (DBU PA2(SCGCQ02086670 port of SCGCQ02082460) 
 - storclif.exe /c0/ex/sx show poh should show proper message during command execution.(SCGCQ02086632 port of SCGCQ02075242) 
 - show/set lane speed shows success when we are in SAS profile(SCGCQ02079507 port of SCGCQ02078437) 
 - Storcli: "show config" command shown as Un-supported.(SCGCQ02075286 port of SCGCQ02064839) 
 - Schema file updates for controller show all output change for defect SCGCQ02048150(SCGCQ02075282 port of SCGCQ02069817) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for "/cx get vpd" commands.(SCGCQ02058567 port of SCGCQ02018140) 
 - Instance Validation Failed between "vd-unmap-schema.json" and "/call/vall show unmap"(SCGCQ02047243 port of SCGCQ02035370) 
 - Instance Validation Failed between "drive-group-schema.json" and "/call/dall show " and /call/dall show all	(SCGCQ02047235 port of SCGCQ02040756) 
 - PH11 PA - StorCLI - Segmentation fault seen when 'compare linkspeed' executed on Fury C0 board(SCGCQ02044794 port of SCGCQ02044777) 
 - Request to Disable DSW3(SCGCQ01903331 port of SCGCQ01896311) 
 - PERCCLI Support for EKMS(SCGCQ01904188 port of SCGCQ01902150) 
 - StorCLI crashes, while trying to enable security on any DG ,incase, when no DG exists(SCGCQ01904340 port of SCGCQ01413253) 
 - Disk performance throttled when running MegaCli AdpEvent log dump on Aspen and Vail (Invader and Intruder(SCGCQ01921529 port of SCGCQ01220901) 
 - Hide "set termlog" help contents from perccli(SCGCQ01935143 port of SCGCQ01923643) 
 - Storcli is not showing foreign configs if user has SED drive which is in foreign(SCGCQ01940869 port of SCGCQ01937410) 
 - Storcli not working on large config setup when some of the drives are missing or the system has foreign config.(SCGCQ01945534 port of SCGCQ01940805) 
 - Storcli- Delay seen in /c0 /vall show all o/p(SCGCQ01965393 port of SCGCQ01935697) 
 - Storcli shows wrong PD list sequence.(SCGCQ01971632 port of SCGCQ01967488) 
 - LD size not shown in GiB format in foreign import preview(SCGCQ01996370 port of SCGCQ01978978) 
 - Unable to switch to eHBA mode using a H745P Adapter(SCGCQ01998964 port of SCGCQ01990060) 
 - perccli show profile lists personality as JBOD instead of eHBA(SCGCQ01998966 port of SCGCQ01998328) 
 - Json Schema for the command "storcli /cx/ex show phyerrorcounters" needs to be updated(SCGCQ02101377 port of SCGCQ02101372) 
 - In ARM server UEFI shell, storcli.efi hangs forever when storcliconf.ini is present(SCGCQ02116733 port of SCGCQ02115036) 
 - complete Lane WWID is not displayed(SCGCQ02145739 port of SCGCQ02145716) 
 - No "Rbld" legend during rebuild.	(SCGCQ02150634 port of SCGCQ02146819) 
 - Error message mismatch is seen for rttdump command on iMR Ventura controller.(SCGCQ02160907 port of SCGCQ02156483) 
 - Storcli throws different error messages for show status command in Ventura and Aero(SCGCQ02086689 port of SCGCQ02078409) 
 - Multiple status messages are displayed in the output	(SCGCQ02086536 port of SCGCQ02073042) 
 - MR_7.10_Storcli: No schema file for controller sesmultipathcfg commands.(SCGCQ02079595 port of SCGCQ02018134) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" JSON output.(SCGCQ02079590 port of SCGCQ02018277) 
 - "Run time to empty" field showing as "Battery is not being charged" when the battery is being charged.(SCGCQ02079535 port of SCGCQ02045324)
 - MR_7.10_Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set personality" JSON output.(SCGCQ02050491 port of SCGCQ02016762) 
 - MR_7.10_Storcli: Add VD command output is not in JSON format.(SCGCQ02050489 port of SCGCQ02034493) 
 - "Invalid RAID level" error message while creating R10 VD.(SCGCQ02047806 port of SCGCQ02034471) 
 - Incorrect status displayed for pause rebuild command.(SCGCQ02046878 port of SCGCQ02043610) 
 - PH11 PA Storcli: Incorrect error message shown while programming invalid sasaddress(SCGCQ02043612 port of SCGCQ02042296) 
 - Aero UTP: storclif /call show commands output contains "Count 4 exceeded for token id #"	(SCGCQ02034200 port of SCGCQ02034064) 
 - Storcli shows wrong PD list sequence.(SCGCQ01977461 port of SCGCQ01967488) 
 - Migrate Failure case is not Branding compliant(SCGCQ02000716 port of SCGCQ01988402) 
 - StorCLI PH12: Retrieving topology details causes application crash in some scenario(SCGCQ02106192 port of SCGCQ02103217) 
 - Support FMP Images in UEFI Version of PERCCli(SCGCQ02116464 port of SCGCQ02078649) 
 - MR 7.11: Storcli.efi: On ARM server, incomplete configuration data received error is observed for any storcli.efi command(SCGCQ02116497 port of SCGCQ02114898) 
 - PH12 PA - StorCLI - 9310-8i IR FW download fails	(SCGCQ02121848 port of SCGCQ02121783) 
 - LibMod changes : MR: 64 Bit Utilities/Application to Support VMWARE ESXi 6.7+(SCGCQ02139867 port of SCGCQ02085102) 
 - MR7.11_Storcli: On drive rebuild, there is a mismatch between the pd rebuild state and respective legend	(SCGCQ02168256 port of SCGCQ02165944) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for /cx/px commands.(SCGCQ02079604 port of SCGCQ02018137) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-patrolread-schema.json" and "/call pause patrolread"(SCGCQ02079597 port of SCGCQ02035437) 
 - Empty data is listed when we query for show linkconfig(SCGCQ02079511 port of SCGCQ02076931) 
 - Libmods: show.set lane speed shows success with wrong data when we are in SAS profile(SCGCQ02079506 port of SCGCQ02078513) 
 - Incorrect status displayed for resume copyback command.	(SCGCQ02075291 port of SCGCQ02062834) 
 - "Delete snapdump" command shows same description "Snapdump clear" for success and failure case.(SCGCQ02075284 port of SCGCQ02065734) 
 - MR_7.10_Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/eall/sall show all"(SCGCQ02050481 port of SCGCQ02018327) 
 - Libmod changes: Adding CLI command to display/toggle new controller property.(SCGCQ01106982(SCGCQ01929892 port of SCGCQ01106988) 
 - Added new commands from StorCLI(SCGCQ01935296 port of SCGCQ01134166) 
 - For NVMe drive use the term NVMe instead of PCIe	(SCGCQ01964024 port of SCGCQ01923119) 
 - securesed autoconfig param should not be present for perccli help(SCGCQ01986879 port of SCGCQ01986831) 
 - Extend major downgrade support in storCLI for SAS3 IT product(SCGCQ02032582 port of SCGCQ02029410) 
 - Drives connected to active backplanes not showing the phy info in connector name	(SCGCQ02112425 port of SCGCQ02112424) 
 - Background operations keep on progressing after hitting /c0 shutdown from storcli(SCGCQ02150630 port of SCGCQ02132024) 
 - Instance Validation Failed for "/call/eall show status" and enclosure-status-schema.json(SCGCQ02153950 port of SCGCQ02150921) 
 - Instance Validation Failed for "/call/cv show all" and cache-vault-detailed-schema.json(SCGCQ02154755 port of SCGCQ02150651) 
 - Storcli: Force is mentioned as optional in snapdump delete command.(SCGCQ02086544 port of SCGCQ02083822) 
 - Port information is not displayed for Vses Backplane	(SCGCQ02085875 port of SCGCQ02053070) 
 - MR_7.9: Storcli reported unknown OS for Windows 10 RS5 LTSC.	(SCGCQ02079601 port of SCGCQ01992461) 
 - spell mistake in start diag operation failure(SCGCQ02079529 port of SCGCQ01998330) 
 - Storcli:"resource already in use" error message displayed when trying to create VD with one UG and one UBUnsp.(SCGCQ02075289 port of SCGCQ02064828) 
 - Storcli: HPE serial number programming and display(SCGCQ02062635 port of SCGCQ01882984) 
 - MR_7.10_Storcli: Instance Validation Failed between "cache-vault-detailed-schema.json" and "/call/cv show all "(SCGCQ02050460 port of SCGCQ02019729) 
 - FW flash fails to load the latest image after upgrade downgrade with resetnow option	(SCGCQ02046879 port of SCGCQ02035152) 
 - Extend major downgrade support in storCLI for SAS3 IT product(SCGCQ02032581 port of SCGCQ02029410) 
 - Storcli throws an 'Incomplete foreign configuration' error when there is no enclosure connected(SCGCQ02007109 port of SCGCQ02006450) 
 - Storcli issuing 'add jbod drives=all' causes storcli to crash(SCGCQ01893381 port of SCGCQ01892288) 
 - LibMods : Adding the function that changing flag of full initialize completion(SCGCQ01930028 port of SCGCQ01141462) 
 - Storcli- Delay seen in /c0 /vall show all o/p(SCGCQ01936895 port of SCGCQ01935697) 
 - Terminology change from " Data protection" to " Data integrity".(SCGCQ01940807 port of SCGCQ01827339) 
 - Libmods: Terminology change from " Data protection" to " Data integrity".(SCGCQ01943370 port of SCGCQ01827732) 
 - Incorrect colinfo output of Bad block count(SCGCQ01977457 port of SCGCQ01977443) 
 - StorCLI hangs when viewing controller in FreeBSD (MR7.8 is okay(SCGCQ01984543 port of SCGCQ01978824) 
 - Unified StorCLI : Help command of "Get flash" is not shown in generic help syntax(SCGCQ01985472 port of SCGCQ01985463) 
 - StorCLI show output shows Legends as BBU instead of EnergyPack.(SCGCQ01992007 port of SCGCQ01985587) 
 - Aero A0 UTP: StorCLI snapdump command needs to clarify new "On Demand" snapdump option(SCGCQ01995066 port of SCGCQ01993722) 
 - Shenandoah:StorCLI:Right click properties for released binary shown blank.(SCGCQ02000843 port of SCGCQ01988329) 
 - Smart Carrier Enclosure port info shown as "Multuipath"(SCGCQ02008273 port of SCGCQ01992087) 
 - MR 7.11: Storcli: Instance Validation Failed for "/call show all" and system-schema.json	(SCGCQ02116771 port of SCGCQ02112192) 
 - "Storcli /c# set jbod=on" shows success but does nothing	(SCGCQ02119067 port of SCGCQ02117219) 
 - Phyreset Fails on IT controllers	(SCGCQ02169305 port of SCGCQ02169242) 
 - Storcli stop erase needs an help file update	(SCGCQ02169308 port of SCGCQ02168895) 
 - Updating phy link reset logic for IT cards with respect to storelib changes(SCGCQ02185911 port of SCGCQ02184862) 
 - Storcli connector display not matching with Aero board 9560-16i.	(SCGCQ02085681 port of SCGCQ02072448) 
 - MR_7.10_Storcli: controller-detailed-properties-schema.json or "/call show all " output not in JSON format(SCGCQ02079610 port of SCGCQ02016771) 
 - MR_7.10_Storcli: No schema file for controller unmap commands.(SCGCQ02079593 port of SCGCQ02016749) 
 - Incorrect error message displayed while creating R10 VD when no free space available.(SCGCQ02075283 port of SCGCQ02067575) 
 - remove the maxconcurrentpd check from storcli and report fw returned failure	(SCGCQ02053931 port of SCGCQ02053910) 
 - PERCCLI Support for EKMS	(SCGCQ01904189 port of SCGCQ01903448) 
 - StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911832 port of SCGCQ01886637) 
 - Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder(SCGCQ01915313 port of SCGCQ01222855) 
 - (Libmods) Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder)(SCGCQ01915315 port of SCGCQ01227144) 
 - perccli /c0 show all lists topology without any DG's present(SCGCQ01998965 port of SCGCQ01998332) 
 - PH12 PA - StorCLI version not getting printed for show file command	(SCGCQ02116759 port of SCGCQ02105185) 
 - Convention comes in same line while performing help for /c0/e0/s0 download.(SCGCQ02176697 port of SCGCQ02176681) 
 - With IT controller for set or reset with invalid phy is not showing error(SCGCQ02183510 port of SCGCQ02181823) 
	
EnhancementRequests:
 - Incorporating VMware constraints for PERCCLI VIB signing	(SCGCQ02190441) 
 - Migrating VMware 64 bit toolchain to 6.8.7-13394445(SCGCQ02190429) 
 - Create an event for DDF config clear failed event.(SCGCQ02173513) 
 -	(SCGCQ02162699) 
 - Snap Dump ClearAll Method logging event(SCGCQ02157359) 
 - API changes for a better presentation of Atlas to tools(SCGCQ02149380) 
 - Add disableOffloadNum field in MR_SNAPDUMP_PROPERTIES struct(SCGCQ02125252) 
 - Better error message for certain unmap operations(SCGCQ02111563) 
 - Add MFI STAT and MR Event for Secure Boot indicating fw dl was not allowed due to an existing pending key change(SCGCQ02103973) 
 - MR Windows IOCTL Error codes to Application added to MR API(SCGCQ02103183) 
 - API changes for linkconfig interface	(SCGCQ02053671) 
 - API changes for NVMe speed and width changes	(SCGCQ02053667) 
 - Reword event log messages as it creates unnecessary panic.(SCGCQ02013675) 
 - Added Windows compiler security flags (SDL and control flow guard(SCGCQ01949495) 
 - Unified StorCLI : Adding component level download functionality to StorCLI(SCGCQ01940030) 
 - show complete Serial Number and Model Name for NVMe drive(SCGCQ01927541) 
 - snapdump support for host initiated snapdump	(SCGCQ01901158) 
 - Changes for disable least latency mode(SCGCQ01891451) 
 - Inspur request to add to show smart info of sas drive for "StorCLI /cx/ex/sx show smart" command(SCGCQ01929656) 
 - MR_SAS_Unified_Libmods_7.10 Inspur request to add to show smart info of sas drive for "StorCLI /cx/ex/sx show smart" command(SCGCQ01979597) 
 - Post firmware trace buffer at the time of driver load(SCGCQ01992779) 
 - Adding the spare details in the same volume creation(CONFIG_ADD DCMD(SCGCQ02008407) 
 - PSoC implementation in StorCLI by parsing PSoC image(SCGCQ02072160) 
 - Request to display the help for "show" and "set" for JBOD in PercCLI	(SCGCQ02160291) 
 - Adding NVACHE messages indicate when SLC format has started and completed.(SCGCQ02137048) 
 - MR API: Add support bits for currentSpeed and clkMode(SCGCQ02132334) 
 - Enable iMR advanced debug dump(SCGCQ02030908) 
 - Unified StorCLI : ARM Windows support to StorCLI(SCGCQ01962294) 
 - Disabling RAID00 support	(SCGCQ01960420) 
 - HPE Shenandoah: Branding tool(SCGCQ01960295) 
 - Added Windows compiler security flags (SDL and control flow guard(SCGCQ01949503) 
 - Unified StorCLI : Allow SBR/SPD read and write using new CBB+SBR concatenated image(SCGCQ01927551) 
 - show complete Serial Number and Model Name for NVMe drive connected to IT controller(SCGCQ01927538) 
 - show complete Serial Number and Model Name for NVMe drive(SCGCQ01919655) 
 - Unified CLI - Command processor changes for handling invalid/tampered device id's for sea IT controllers(SCGCQ01891513) 
 - Add support to display PSOC version for Ventura IT controllers(SCGCQ02067300) 
 - set copyback command changes for cli(SCGCQ02148092) 
 - Unified StorCLI : ARM64 Windows support to StorCLI - LibMod changes(SCGCQ01963208) 
 - Shenandoah: Adding support bit check for delete snap dump(SCGCQ01944500) 
 - Enable iMR advanced debug dump(SCGCQ01873124) 
 - Unified StorCLI : PSoC read and write via Device read and write DCMD's in MR Operational case(SCGCQ01949521) 
 - Changes for disable least latency mode(SCGCQ01891442) 
 - Adding the spare details in the same volume creation (CONFIG_ADD DCMD(SCGCQ02008403) 
 - Unified StorCLI : Allow erase functionality on operational MR using CBB concatenated image(SCGCQ01927595) 
 - Unified CLI : Handling invalid/tampered controllers for sea controllers(SCGCQ01891484) 
 - Requesting StorCLIF to read MR FW from flash device and write it to a file. Similar to what IT FW support.(SCGCQ01631948) 
 - Add ability to field upgrade PSOC on HBA boards(SCGCQ01583214) 
 - DUal Image SUpport(SCGCQ01960287) 
 - Libmods: Porting HPE Shenandoah from Aero to 7.9	(SCGCQ01917263) 
 - Porting HPE Shenandoah from Aero to 7.9(SCGCQ01917172) 
 - Adding HPE specific help for storcli	(SCGCQ01935699) 


007.0816.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------

defects:
  - Improve Debuggablity for MegaRAID Windows Driver by Adding RT Trace - new modifications(SCGCQ01824574 port of SCGCQ01824569) 
 - displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state"(SCGCQ01827604 port of SCGCQ01681538) 
 - Updating makefile and EFI's INF changes for ARM StorCLIO(SCGCQ01870684 port of SCGCQ01563125) 
 - Square bracket is missing in the syntax of "set hardware device page" in storclio.(SCGCQ01929787 port of SCGCQ01224857) 
 - failure in StorCLI enclosure show status	(SCGCQ02043616 port of SCGCQ02040640) 
 - MR_7.10_Storcli: Instance Validation Failed between "virtual-drive-detailed-schema.json" and "/call/vall show all "(SCGCQ02050471 port of SCGCQ02018333) 
 - MR_7.10_Storcli: unmap attribute is not mentioned in "/c0 add vd" command syntax in Schema_mapping_list.xlsx file.(SCGCQ02050535 port of SCGCQ02016758) 
 - Aero DBU PA1:Storcli: Instance Validation Failed "controller-properties-schema" and "/call show" command.(SCGCQ02061387 port of SCGCQ02035439) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for drive jbod commands.(SCGCQ02079592 port of SCGCQ02018135) 
 - MR_7.10_Storcli: bbu-show-modes-schema.json file is not in JSON format.(SCGCQ02079618 port of SCGCQ02019740) 
 - perccli /c0 show all lists topology without any DG's present(SCGCQ02085925 port of SCGCQ01998332) 
 - Libmod changes for StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers(SCGCQ01853370 port of SCGCQ01775616) 
 - (SCGCQ01775602 port of SCGCQ01814011)
 - show enclosure command is not exiting to shell(SCGCQ01874899 port of SCGCQ01814011) 
 - StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911831 port of SCGCQ01886637) 
 - Storcli shows incorrect output for delete events command	(SCGCQ02046875 port of SCGCQ02045816) 
 - Storcli help file doesn't show recon rate command instead it shows migrate rate.(SCGCQ02047747 port of SCGCQ02046036) 
 - Storcli reported "Boot Volume Supported = NO" eventhough ctrl boot with OS on vd.(SCGCQ02047809 port of SCGCQ02030652) 
 - PH11 Alpha - StorCLI - 'show file' command displays incorrect message after reading uploaded bios file(SCGCQ02064703 port of SCGCQ02063689) 
 - Typo in storcli /c0 set linkspeed help(SCGCQ02074664 port of SCGCQ02070951) 
 - Drive Size Display Miss Match In Storcli Show Output(SCGCQ02075280 port of SCGCQ02072353) 
 - BreakMirror RAID Support coming as Yes, even when Breakmirror is not supported(SCGCQ02075281 port of SCGCQ02048150) 
 - Storcli: "resume migrate" command does not show syntax error.(SCGCQ02075292 port of SCGCQ02061340) 
 - Storcli displays drive state as UBad instead of UBad (unsupported(SCGCQ02079521 port of SCGCQ02031615) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON output.(SCGCQ02079591 port of SCGCQ02018305) 
 - CLI returns wrong error code upon failure(SCGCQ02085528 port of SCGCQ02084966) 
 - Wide port info is not displayed under connector name for Backplane attached drives.(SCGCQ02085666 port of SCGCQ02076923) 
 - Libmod changes for SCGCQ02090770	(SCGCQ02097658 port of SCGCQ02096774) 
 - Hide/Unhide command output display incorrect VD no for VDs on which the operation is not supported(SCGCQ01850374 port of SCGCQ01837932) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ02009900 port of SCGCQ01761309) 
 - Storcli pop-up a message "controller not found" during chip reset , rather than controller busy.(SCGCQ02047079 port of SCGCQ02024740) 
 - unmap attribute is not mentioned in help file command "add vd each r0".(SCGCQ02047095 port of SCGCQ02042106) 
 - Instance Validation Failed between "drive-group-hidden-schema" and "/c1/dall set hidden" & "set security"(SCGCQ02047136 port of SCGCQ02040779) 
 - Unified StorCLI : Individual SL_INIT_LIB calls are made for every SL command invocation(SCGCQ02047893 port of SCGCQ02047100) 
 - Spell mistake on support ondemand snapdump property of show all output(SCGCQ02053926 port of SCGCQ02053923) 
 - iMR Changing profileid's using cli results in Status=Success Description=None(SCGCQ02056156 port of SCGCQ02008676) 
 - Show Snapdump help command lists delete snapdump details as well.(SCGCQ02075287 port of SCGCQ02064836) 
 - Need a space between atleast with StorCLI error message "Unmap is not supported atleast on one device"(SCGCQ02075290 port of SCGCQ02064120) 
 - Recon command (./storcli /cx set recon(SCGCQ02086570 port of SCGCQ02081415) 
 - Enhance the detailed help for Firmware download and get bios command.(SCGCQ01792109 port of SCGCQ01790167) 
 - PH11 PA - StorCLI - Segmentation fault seen when 'compare linkspeed' executed on Fury C0 board(SCGCQ02044794 port of SCGCQ02044777) 
 - Instance Validation Failed between "drive-group-schema.json" and "/call/dall show " and /call/dall show all(SCGCQ02047235 port of SCGCQ02040756) 
 - Instance Validation Failed between "vd-unmap-schema.json" and "/call/vall show unmap"(SCGCQ02047243 port of SCGCQ02035370) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for "/cx get vpd" commands.(SCGCQ02058567 port of SCGCQ02018140) 
 - Schema file updates for controller show all output change for defect SCGCQ02048150(SCGCQ02075282 port of SCGCQ02069817) 
 - Storcli: "show config" command shown as Un-supported.(SCGCQ02075286 port of SCGCQ02064839) 
 - show/set lane speed shows success when we are in SAS profile	(SCGCQ02079507 port of SCGCQ02078437) 
 - storclif.exe /c0/ex/sx show poh should show proper message during command execution.(SCGCQ02086632 port of SCGCQ02075242) 
 - Aero (DBU PA2)(SCGCQ02086670 port of SCGCQ02082460) 
 - StorCLI listing PD Slot Status as "Incorrect Status Value" for configured PD's(SCGCQ02097676 port of SCGCQ02090770) 
 - Error message when Maximum number of VDs are reached	(SCGCQ01857450 port of SCGCQ01856544) 
 - Aero UTP: storclif /call show commands output contains "Count 4 exceeded for token id #"	(SCGCQ02034200 port of SCGCQ02034064) 
 - PH11 PA Storcli: Incorrect error message shown while programming invalid sasaddress(SCGCQ02043612 port of SCGCQ02042296) 
 - Incorrect status displayed for pause rebuild command.(SCGCQ02046878 port of SCGCQ02043610) 
 - "Invalid RAID level" error message while creating R10 VD.(SCGCQ02047806 port of SCGCQ02034471) 
 - MR_7.10_Storcli: Add VD command output is not in JSON format.(SCGCQ02050489 port of SCGCQ02034493) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set personality" JSON output.(SCGCQ02050491 port of SCGCQ02016762) 
 - "Run time to empty" field showing as "Battery is not being charged" when the battery is being charged.(SCGCQ02079535 port of SCGCQ02045324) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" JSON output.(SCGCQ02079590 port of SCGCQ02018277) 
 - MR_7.10_Storcli: No schema file for controller sesmultipathcfg commands.(SCGCQ02079595 port of SCGCQ02018134) 
 - Multiple status messages are displayed in the output	(SCGCQ02086536 port of SCGCQ02073042) 
 - Storcli throws different error messages for show status command in Ventura and Aero(SCGCQ02086689 port of SCGCQ02078409) 
 - Improve Debuggablity for MegaRAID Windows Driver by Adding RT Trace - new modifications(SCGCQ01825986 port of SCGCQ01824570) 
 - Turn on the boodrive by storcli, HII does not reflect it, still shows "Off"(SCGCQ01832791 port of SCGCQ01816927) 
 - Add interface in storecli that could get relearn complete status	(SCGCQ01850373 port of SCGCQ01848387) 
 - MR_7.10_Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/ eall/sall show all"(SCGCQ02050481 port of SCGCQ02018327) 
 - "Delete snapdump" command shows same description "Snapdump clear" for success and failure case.(SCGCQ02075284 port of SCGCQ02065734) 
 - Incorrect status displayed for resume copyback command.(SCGCQ02075291 port of SCGCQ02062834) 
 - Libmods: show.set lane speed shows success with wrong data when we are in SAS profile(SCGCQ02079506 port of SCGCQ02078513) 
 - Empty data is listed when we query for show linkconfig(SCGCQ02079511 port of SCGCQ02076931) 
 - MR_7.10_Storcli: Instance Validation Failed between "controller-patrolread-schema.json" and "/call pause patrolread"	(SCGCQ02079597 port of SCGCQ02035437) 
 - MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for /cx/ px commands.(SCGCQ02079604 port of SCGCQ02018137) 
 - Aero - LibMod changes for ER SCGCQ01813156 : Addition of Aero and Sea device id's and checkwords	(SCGCQ01853418 port of SCGCQ01813626) 
 - Storcli throws an 'Incomplete foreign configuration' error when there is no enclosure connected(SCGCQ02007109 port of SCGCQ02006450) 
 - Extend major downgrade support in storCLI for SAS3 IT product(SCGCQ02032581 port of SCGCQ02029410) 
 - FW flash fails to load the latest image after upgrade downgrade with resetnow option	(SCGCQ02046879 port of SCGCQ02035152) 
 - MR_7.10_Storcli: Instance Validation Failed between "cache-vault-detailed-schema.json" and "/call/cv show all "(SCGCQ02050460 port of SCGCQ02019729) 
 - Storcli:"resource already in use" error message displayed when trying to create VD with one UG and one UBUnsp.(SCGCQ02075289 port of SCGCQ02064828) 
 - spell mistake in start diag operation failure(SCGCQ02079529 port of SCGCQ01998330) 
 - MR_7.9: Storcli reported unknown OS for Windows 10 RS5 LTSC.(SCGCQ02079601 port of SCGCQ01992461) 
 - Port information is not displayed for Vses Backplane	(SCGCQ02085875 port of SCGCQ02053070) 
 - Storcli: Force is mentioned as optional in snapdump delete command.(SCGCQ02086544 port of SCGCQ02083822) 
 - Add get VPD command support to StorCLI in OS environment	(SCGCQ01855067 port of SCGCQ01852603) 
 - Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01977760 port of SCGCQ01948579) 
 - CSET: Checking in Libmod changes for defect SCGCQ02030652 - (SCGCQ02045948(SCGCQ02047884 port of ) 
 - remove the maxconcurrentpd check from storcli and report fw returned failure	(SCGCQ02053931 port of SCGCQ02053910) 
 - Incorrect error message displayed while creating R10 VD when no free space available.(SCGCQ02075283 port of SCGCQ02067575) 
 - MR_7.10_Storcli: No schema file for controller unmap commands.(SCGCQ02079593 port of SCGCQ02016749) 
 - MR_7.10_Storcli: controller-detailed-properties-schema.json or "/call show all " output not in JSON format(SCGCQ02079610 port of SCGCQ02016771) 
 - Storcli connector display not matching with Aero board 9560-16i.(SCGCQ02085681 port of SCGCQ02072448)

EnhancementRequest:
- Updating ncurses library from 6.0 to 6.1(SCGCQ01836749) 
 - Command processor changes for Secure boot properties feature - SCGCQ01855473	(SCGCQ01855503) 
 - Adding secure boot properties to unified StorCLI	(SCGCQ01855473) 
 - Adding new MFI STAT - MFI_STAT_SECURE_BOOT_KEY_SLOTS_FULL 007.0711.0000.0000 for Lenovo(SCGCQ01865190) 

007.0713.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------
 - Storcli returns error for show file commands when parsing MR images eventhough the command was successful(SCGCQ01529009) 
 - "Cached Virtual Drives" displayed in /c0/dall show cachecade without the table.(SCGCQ01537017) 
 - storcli /c0 set sasaddhi =xxxx sasaddlow =xxxx displays incomplete sasaddress(SCGCQ01540807) 
 - storcli controller show all lists EPD's in VD list(SCGCQ01556595) 
 - controller show all command is not listing the Battery information(SCGCQ01561689) 
 - Commands "/call/all" return inappropriate message or segfault when both MR and IT controllers are connected(SCGCQ01561703) 
 - Instance Validation Failed between "vd-operations-migrate-schema.json" and "start migrate" JSON output.(SCGCQ01571207) 
 - Storcli: drive-group-security-schema.json is not present in the JSON Schema folder(SCGCQ01571280) 
 - Storcli: Instance Validation Failed between "drive_group_mirror_schema.json" and "/call/dall add mirror src=0" JSON output.(SCGCQ01571298) 
 - Instance Validation Failed "foreign-configuration-detailed-schema.json" and "/call/fall import preview" JSON output(SCGCQ01571393) 
 - "drive-power-on-schema.json" is named as "drive-get-power-on-schema.json" in "Schema_mapping_list" file.(SCGCQ01573229) 
 - Get VPD from MPB region is failure, but overalll status shows success(SCGCQ01589618) 
 - BBU-show-schema is not present in the schema mapping list, the list needs to be sorted to remove duplicate commands.(SCGCQ01599473) 
 - Coverity defect fixes for Uninitialized Variables, resource leaks(SCGCQ01600257) 
 - Spell mistake in error message for hwdev command(SCGCQ01614972) 
 - Coverity defect fix for itctflash file(SCGCQ01616369) 
 - Fixing coverity issues - Resource leaks - Part 5(SCGCQ01627961) 
 - Fixing coverity issues - Non array deletes - Part 6(SCGCQ01629478) 
 - CLI help does not reflect the new command to create an ePD(SCGCQ01639583) 
 - ModeE drive fw download not working when drive image is more than 32K(SCGCQ01681086) 
 - Space need in the output for Deprecated command in storclif64.exe when legacy Cli command is used(SCGCQ01687653) 
 - Grammatical mistakes in Perccli Un-supported RAID level warning message.(SCGCQ01714033) 
 - storclif /c0 start diag type=0, gives syntax error(SCGCQ01714663) 
 - Correcting the grammatical errors in firmware's MFI Stat messages(SCGCQ01717315) 
 - Unified StorCLI 7.7 : Unconfigured BAD drives are not displayed in /c0 show output(SCGCQ01718269) 
 - MR 7.7 - Storcli throws an incorrect error msg while importing foreign config from Raid to JBOD mode.(SCGCQ01718981) 
 - Unmap property is not displayed for a drive in drive show all command output(SCGCQ01720959) 
 - Unified StorCLI 7.7 : StorCLI should allow noreset option when current NVDATA is lesser than the new NVDATA for SAS3.5 IT(SCGCQ01727159) 
 - Enclosure show status command gives success but nothing is shown(SCGCQ01731280) 
 - Unified StorCLI 7.7 : StorCLI doesn't report failure status when nopad image flashing fails via completeflash command in MR(SCGCQ01749849) 
 - Help content for jbodx show unmap is not present(SCGCQ01790130) 
 - One of the requirement for Criteo is to display JBOD-WB (EPD) to OS drive mapping.(SCGCQ01804763) 
 - Turn on the boodrive by storcli, HII does not reflect it, still shows "Off"(SCGCQ01816927) 
 - Incorrect Interface Details for "storcli /c0 show" command(SCGCQ01837612) 
 - MR API - Incorrect value used for MR_DCMD_CTRL_SNAPDUMP_ONDEMAND(SCGCQ01882581) 
 - storclio command not working to update FW on SATA disk(SCGCQ01918814) 
 - Storcli- Delay seen in /c0 /vall show all o/p(SCGCQ01935697) 
 - Phase3 Beta PCIe: Loading SLOOB fails with error message "ExitLib failed for SAS IT Controller!! rval 0x801A"(SCGCQ01292964) 
 - storcli /cx/pall show command fails with older generation cards that does not support PCIe pages(SCGCQ01520816) 
 - Storcli: vd-delete-schema.json is not present in the JSON Schema folder(SCGCQ01571254) 
 - Instance Validation Failed between "controller-properties-schema.json" and "/call show" JSON output.(SCGCQ01573076) 
 - Unified LibMods : Fixing coverity issues - Resource leaks and Uninitialized variables - Part 2(SCGCQ01600381) 
 - Unified LibMods : Coverity fixes for uninitialized variables in File functions - Part 4(SCGCQ01606830) 
 - Checking in VBAS compliation changes(SCGCQ01630324) 
 - PERCCLI ePD personality behavior command is still an available option and has not been removed(SCGCQ01639798) 
 - Instance Validation Failed "system-schema.json" and "storcli64.exe show all" JSON output.(SCGCQ01640825) 
 - Storcli: VD creation fails from storcli in presence of 0KB bad drive .(SCGCQ01713240) 
 - Space need in the output for secure erase(SCGCQ01713604) 
 - PA2-MR7.7-StorCLI: "storcli /c0/v239 start migrate type=raid0 option=add drives=66:18" gives syntax error(SCGCQ01713681) 
 - Drive Listing Is Not In Order for "/c0 show" & "/c0/eall/sall show"(SCGCQ01714356) 
 - StorCLI 7.702 help for SnapDump is not clear(SCGCQ01715025) 
 - IT Fw Download command StorCLI /c0/eall/sall hang(SCGCQ01723226) 
 - Unified StorCLI Phase 8 : No help section for ForceHCB option(SCGCQ01731292) 
 - Unified CLI 7.7 : Fixing coverity issues - Resource leaks,Unused variables,and non-array deletes - Part 1(SCGCQ01732959) 
 - Unified StorCLI Phase 8 : Firmware downgrade should be supported only by StorCLIO for SAS3 IT controllers(SCGCQ01734559) 
 - Storcli does not display the complete enclosure serial number(SCGCQ01735493) 
 - Storcli vib update fails across releases.(SCGCQ01761795) 
 - StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers(SCGCQ01775602) 
 - StorCLI enable/disable unmap VDs return status as failed instead of successful(SCGCQ01803306) 
 - Removing the set/show of unmap on JBOD.(SCGCQ01817855) 
 - Unified StorCLI 7.6 : Read SBR fails with pre-ventura controllers(SCGCQ01539360) 
 - Storcli: Instance Validation Failed between "drive-group-detailed-schema.json" and "/call/dall show all" JSON output.(SCGCQ01571287) 
 - Instance Validation Failed between "foreign-configuration-schema.json" and "/call/fall show" JSON output.(SCGCQ01571391) 
 - Instance Validation Failed between "controller-detailed-properties-schema.json" and "/call show all" JSON output.(SCGCQ01573096) 
 - "drive-security-key-schema.json" is named as "drive-securitykey-schema.json" in "Schema_mapping_list" file.(SCGCQ01573226) 
 - CLI does not report Serial number for Enclosure.(SCGCQ01595640) 
 - Json schema for enclosure phyerrorcounters has not been added, output format needs modification.(SCGCQ01595673) 
 - Unified StorCLI 7.7 : SAS Phyloopback test reports false positive results(SCGCQ01624063) 
 - Update help contents for jbod delete(SCGCQ01624605) 
 - Drive download commands help syntax to be updated for IT.(SCGCQ01681089) 
 - Grammatical error in Perccli warning message during FW Flash.(SCGCQ01686670) 
 - Missing punctuation in Perccli delete config message(SCGCQ01698226) 
 - Personality Behavior Modes:Command returns failure when setting non-RAID behavior modes.(SCGCQ01713265) 
 - Unified StorCLI Phase 8 : NVMe and SAS Drive's WWN is incorrect for IT Controller(SCGCQ01749795) 
 - Storcli is not showing foreign configs if user has SED drive which is in foreign(SCGCQ01937410) 
 - controller show wbsupport reason is not listed in the cli output(SCGCQ01561704) 
 - Application crashes while executing storcli64.exe /c0/dall set hidden=on(SCGCQ01571256) 
 - Instance Validation Failed between "system-schema.json" and "show all" JSON output.(SCGCQ01571961) 
 - Unified StorCLI 7.7 : Coverity issues - Resource leaks,Uninitialized variables,and dead code - Part 1(SCGCQ01600195) 
 - Drive Fw download Coverity fixes(SCGCQ01615074) 
 - Unified StorCLI 7.7 : StorCLI should not issue SL_SET_LIB_PARAMETERS command(SCGCQ01676983) 
 - Detailed status is not displayed on locating a drive which is not connected to IT card.(SCGCQ01571154) 
 - Coverity defect fixes for Memory Leak, Uninitialized pointers(SCGCQ01605182) 
 - storclio need to support proprietary i2c controller mode.(SCGCQ01732990) 
 - MR7.7 LSA 4.180.0 enclosure type is not matched with storcli(SCGCQ01747333) 
 - Coverity libmods issues - Resource leaks and Wrong sizes(SCGCQ01600208) 
 - Unified StorCLI 7.7 : MegaCLI commands report command status code in UEFI environment(SCGCQ01624506) 
 - storcli did not show current profile when connection in invalid config.(SCGCQ01713676) 
 - Unmap support mfc bit and fde type mixing fields needs to be updated when extracting factory settings and also while modifying factory settings(SCGCQ01640217) 	
 - non-RAID:HII:CLI:Dedicated Hot Spare creation displays incorrect disk group association.(SCGCQ01698272) 
 - DHS:Unable to add dedicated Hot Spare drive to specified DG.(SCGCQ01714443) 
 - WWN for NVME PDs is reported as NA with MR(SCGCQ01731279) 
 - Updating the Diag results as per new API changes(SCGCQ01537255) 
 - Resource leaks,Uninitialized variables(SCGCQ01600311) 
 - Unified CLI : Coverity fixes for Uninitialized variables,resource leaks,and dead code handling - Part 3(SCGCQ01606785) 
 - Unified StorCLI 7.7 - Fixing coverity issues Resource leaks,Non-array deletes - Part 2(SCGCQ01757433) 
 - Storcli: UEFI shell error display-Error: Unsupported File open Mode.(SCGCQ01837752) 
 - Removal of ncurses references for linux makefile(SCGCQ01955544) 
  - Changing ini file name to storelibconfit.ini(SCGCQ01275669 port of SCGCQ01275496) 
 - Changing ini file name to storelibconfit.ini(SCGCQ01275670 port of SCGCQ01275496) 
 - Enumeration of drives in NGM[PERCCLI Implementation / HBA330 Mini Mezz](SCGCQ01529059 port of SCGCQ01458174) 
 - Storcli PR help execution delay is missing when PR running continuously(SCGCQ01537219 port of SCGCQ01534552) 
 - Handle memory leaks in getSortedPdList(SCGCQ01571890 port of SCGCQ01283497) 
 - Disk sorting based on connector name, slot and position(SCGCQ01571926 port of SCGCQ01307257) 
 - Collecting snapdump through StorCli(SCGCQ01594186 port of SCGCQ01581899) 
 - Unified StorCLI 7.6 : Creation of VD aborts StorCLI when FW returns error code for MR_DCMD_CFG_READ DCMD(SCGCQ01595361 port of SCGCQ01588245) 
 - Allow "noreset" option for IT controllers during firmware download(SCGCQ01599545 port of SCGCQ01514483) 
 - Enumeration of drives in NGM[PERCCLI Implementation / HBA330 Mini Mezz](SCGCQ01600137 port of SCGCQ01458174) 
 - StorCLI should not display SED property when using IT-HBA(SCGCQ01600142 port of SCGCQ01589445) 
 - Cutlass Phase 16 Storcli: Partner device ID should be suppressed under ./storcli /c0/eall show for multipath connections(SCGCQ01619201 port of SCGCQ01606780) 
 - Storcli should not create a snapdump image if there is no valid image(SCGCQ01624677 port of SCGCQ01623883) 
 - Removing readonly properties from for snapdump in storcli.(SCGCQ01669986 port of SCGCQ01669570) 
 - Different RetCode for N/A Drives - Parallel Drive Update(SCGCQ01682236 port of SCGCQ01681478) 
 - Storcli: VD creation fails from storcli in presence of 0KB bad drive .(SCGCQ01713567 port of SCGCQ01713240) 
 - Flashing PD's with parallel option wrong status is given by Storcli(SCGCQ01714667 port of SCGCQ01713734) 
 - Missing punctuation in Perccli delete config message(SCGCQ01714668 port of SCGCQ01698226) 
 - When a bad PD is flashed it fails as expected but error code is wrong(SCGCQ01714670 port of SCGCQ01713728) 
 - Parallel drive fw update on 1st drive fails, while drive fW update on another drive is in progress(SCGCQ01714671 port of SCGCQ01676426) 
 - Enclosure show status command gives success but nothing is shown(SCGCQ01731381 port of SCGCQ01731280) 
 - storclio need to support proprietary i2c controller mode.(SCGCQ01801679 port of SCGCQ01732990) 
 - Phase 7 - Drive Listing Is Not In Order for "/c0 show" & "/c0 show all"(SCGCQ01810054 port of SCGCQ01809355) 
 - EPD-PT behavior changes for Aero to support in RAID personality(SCGCQ01816139 port of SCGCQ01594176) 
 - perccli /cx delete config command getting incorrect error message.(SCGCQ01851908 port of SCGCQ01850719) 
 - State of the tape drive should be displayed as "JBOD" when FW state is MR_PD_STATE_SYSTEM(SCGCQ01853457 port of SCGCQ01853444) 
 - StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911830 port of SCGCQ01886637) 
 - (Libmods) Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder)(SCGCQ01915314 port of SCGCQ01227144) 
 - Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder(SCGCQ01915320 port of SCGCQ01222855) 
 - Updating ncurses library from 6.0 to 6.1(SCGCQ01915841 port of SCGCQ01836749) 
 - Disk performance throttled when running MegaCli AdpEvent log dump on Aspen and Vail (Invader and Intruder(SCGCQ01921533 port of SCGCQ01220901) 
 - Libmod changes: Adding CLI command to display/toggle new controller property.(SCGCQ01106982(SCGCQ01922038 port of SCGCQ01106988) 
 - LibMods : Adding the function that changing flag of full initialize completion(SCGCQ01922843 port of SCGCQ01141462) 
 - MFI Frame alignment(SCGCQ01922846 port of SCGCQ01064480) 
 - Square bracket is missing in the syntax of "set hardware device page" in storclio.(SCGCQ01929787 port of SCGCQ01224857) 
 - Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01526330 port of SCGCQ01274709) 
 - Change in RAID levels displaying in controller show all command(SCGCQ01540785 port of SCGCQ01509578) 
 - Ctrl-H hang during foreign import along with app tab toggling.(SCGCQ01571937 port of SCGCQ01356240) 
 - Data Abort Exception while entering CTRL R(SCGCQ01571939 port of SCGCQ01380831) 
 - Storcli_Aero: Storcli not able to detect controller at EFI shell without Avago MR driver.(SCGCQ01599436 port of SCGCQ01595698) 
 - This feature is not supported on this Controller" is displayed multiple times.(SCGCQ01599461 port of SCGCQ01595717) 
 - Unified StorCLI 7.6 : Creation of VD aborts StorCLI when FW returns error code for MR_DCMD_CFG_READ DCMD(SCGCQ01600150 port of SCGCQ01588245) 
 - Snapdump file user does not know the compression method(SCGCQ01624670 port of SCGCQ01616917) 
 - Storcli_Aero: unable to set sasadd methodport on IT controller.(SCGCQ01628097 port of SCGCQ01609234) 
 - Patrol read state shown as aborted while it actually is paused.(SCGCQ01714666 port of SCGCQ01714264) 
 - Storcli output does not list missing PD's(SCGCQ01715372 port of SCGCQ01715114) 
 - Grammatical mistakes in Perccli Un-supported RAID level warning message.(SCGCQ01720760 port of SCGCQ01714033) 
 - Unified StorCLI Phase 8 : NVMe and SAS Drive's WWN is incorrect for IT Controller(SCGCQ01749927 port of SCGCQ01749795) 
 - storcli /cx/pall show command fails with older generation cards that does not support PCIe pages(SCGCQ01758163 port of SCGCQ01520816) 
 - PERC10.2:CLI:Help: Grammatical Error in Text String "/ex - specifies a enclosure where X is the enclosure device ID."(SCGCQ01768428 port of SCGCQ01764888) 
 - "storcli show snapdump" output is incorrect(SCGCQ01817308 port of SCGCQ01817307) 
 - StorCLI should support firmware flash for SAS3 IR Controllers(SCGCQ01873578 port of SCGCQ01835627) 
 - show enclosure command is not exiting to shell(SCGCQ01874899 port of SCGCQ01814011) 
 - Storcli issuing 'add jbod drives=all' causes storcli to crash(SCGCQ01893370 port of SCGCQ01892288) 
 - Hide/Unhide command output display incorrect VD no for VDs on which the operation is not supported(SCGCQ01911848 port of SCGCQ01837932) 
 - Turn on the boodrive by storcli, HII does not reflect it, still shows "Off"(SCGCQ01915791 port of SCGCQ01816927) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ01917007 port of SCGCQ01761309) 
 - PH9 PA StorCLI - /c0/eall/sal show all gives success message when no drives connected(SCGCQ01917168 port of SCGCQ01855721) 
 - Storcli: Ventura B0: BIOS Flashing Failure Observed in EFI Storcli and Multiple Tries Causes UART Unresponsive(SCGCQ01917338 port of SCGCQ01829667) 
 - Adding CLI command to display/toggle new controller property.(SCGCQ01922836 port of SCGCQ01106982) 
 - Storcli not working on large config setup when some of the drives are missing or the system has foreign config.(SCGCQ01940851 port of SCGCQ01940805) 
 - Expander FW download using storecli utility crashs.(SCGCQ01979615 port of SCGCQ01979599) 
 - Updating readme file(SCGCQ01294583 port of SCGCQ01294570) 
 - Remove sorting logic for array physical drives(SCGCQ01445612 port of SCGCQ01444666) 
 - Add /dev/sdX to StorCLI output(SCGCQ01514530 port of SCGCQ01505055) 
 - Allow "noreset" option for IT controllers during firmware download(SCGCQ01517643 port of SCGCQ01514483) 
 - Libmod: checking-in the changes forLibmods for SCGCQ01525764(SCGCQ01528935 port of SCGCQ01528886) 
 - Libmod: checking-in the changes forLibmods for SCGCQ01525764(SCGCQ01528936 port of SCGCQ01528886) 
 - Implemented to display the full Model number of the SATA drive when connected to an IT controller.(SCGCQ01528939 port of SCGCQ01525764) 
 - Unified StorCLI 7.6 : Read SBR fails with pre-ventura controllers(SCGCQ01539390 port of SCGCQ01539360) 
 - Removal of MegaCLI syntax from StorCLI(SCGCQ01591157 port of SCGCQ01504604) 
 - Unified LibMod changes for ER : SCGCQ01504604 - Removal of MegaCLI syntax from StorCLI(SCGCQ01591158 port of SCGCQ01504610) 
 - Spell error in /call/dall split mirror output.(SCGCQ01599464 port of SCGCQ01595709) 
 - storcli controller show all lists EPD's in VD list(SCGCQ01599486 port of SCGCQ01556595) 
 - Detailed status is not displayed on locating a drive which is not connected to IT card.(SCGCQ01599519 port of SCGCQ01571154) 
 - Storcli returns error for show file commands when parsing MR images eventhough the command was successful(SCGCQ01600149 port of SCGCQ01529009) 
 - Storcli_Aero: Storcli not able to detect controller at EFI shell without Avago MR driver.(SCGCQ01600151 port of SCGCQ01595698) 
 - Support only Dell SAS IT Controllers with PERCCLI(SCGCQ01618493 port of SCGCQ01547929) 
 - Cutlass Phase 16 Storcli: Partner device ID should be suppressed under ./storcli /c0/eall show for multipath connections(SCGCQ01625114 port of SCGCQ01606780) 
 - Cached IO policy(SCGCQ01627941 port of SCGCQ01607434) 
 - Space need in the output for secure erase(SCGCQ01714669 port of SCGCQ01713604) 
 - Unified StorCLI 7.7 : Unconfigured BAD drives are not displayed in /c0 show output(SCGCQ01718294 port of SCGCQ01718269) 
 - Unified StorCLI 7.7 : StorCLI doesn't report failure status when nopad image flashing fails via completeflash command in MR(SCGCQ01749921 port of SCGCQ01749849) 
 - storcli did not show current profile when connection in invalid config.(SCGCQ01760598 port of SCGCQ01713676) 
 - non-RAID:HII:CLI:Dedicated Hot Spare creation displays incorrect disk group association.(SCGCQ01760604 port of SCGCQ01698272) 
 - Storcli does not display the complete enclosure serial number(SCGCQ01760655 port of SCGCQ01735493) 
 - "storcli show snapdump" output is incorrect(SCGCQ01817270 port of SCGCQ01804779) 
 - Fails to set user defined value for delayOCR field in the SnampDump(SCGCQ01817941 port of SCGCQ01817465) 
 - Fails to set SnapDump savecount.(SCGCQ01817942 port of SCGCQ01817177) 
 - displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state"(SCGCQ01836905 port of SCGCQ01681538) 
 - Error message when Maximum number of VDs are reached(SCGCQ01911765 port of SCGCQ01856544) 
 - perccli /cx delete config command getting incorrect error message.(SCGCQ01911827 port of SCGCQ01850719) 
 - Unified LibMod changes : Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01913460 port of SCGCQ01893074) 
 - Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01913461 port of SCGCQ01892560) 
 - Add interface in storecli that could get relearn complete status(SCGCQ01914835 port of SCGCQ01848387) 
 - 6.13_SDS : Wrong error message is displayed on trying to create R0 vd on an pre configured drive as EPD.(SCGCQ01922844 port of SCGCQ01196785) 
 - Added new commands from StorCLI(SCGCQ01922845 port of SCGCQ01134166) 
 - Unified StorCLI : Enclosure devices are part of drive list used for drive operations(SCGCQ01979534 port of SCGCQ01979483) 
 - Add /dev/sdX to StorCLI output(SCGCQ01514531 port of SCGCQ01514516) 
 - Prepare To Transport(SCGCQ01568934 port of SCGCQ00936041) 
 - CacheCade VD association returns error in Config Utility (Ctrl-R(SCGCQ01571889 port of SCGCQ01264552) 
 - .(SCGCQ01571935 port of SCGCQ01325052) 
 - Commands "/call/all" return inappropriate message or segfault when both MR and IT controllers are connected(SCGCQ01599483 port of SCGCQ01561703) 
 - Un-supported command displayed for "storcli64.exe /call show sasaddress"(SCGCQ01620412 port of SCGCQ01619562) 
 - Update help contents for jbod delete(SCGCQ01625945 port of SCGCQ01624605) 
 - Storcli_Aero: unable to set sasadd methodport on IT controller.(SCGCQ01628094 port of SCGCQ01609234) 
 - Libmod Changes for Defect SCGCQ01595640 (CLI does not report Serial number for Lenovo D1224 Enclosure(SCGCQ01714307 port of SCGCQ01664412) 
 - Drive Listing Is Not In Order for "/c0 show" & "/c0/eall/sall show"(SCGCQ01732928 port of SCGCQ01714356) 
 - controller show wbsupport reason is not listed in the cli output(SCGCQ01760590 port of SCGCQ01561704) 
 - Storcli does not display the complete enclosure serial number(SCGCQ01760636 port of SCGCQ01735493) 
 - "Cached Virtual Drives" displayed in /c0/dall show cachecade without the table.(SCGCQ01760676 port of SCGCQ01537017) 
 - Trying to import Secured LDs and if wrong Security Key is mentioned, Error is referring to "Pass phrase"(SCGCQ01764539 port of SCGCQ01763866) 
 - Libmods: SCGCQ01760508 Error message-"Reached Maximum Supported virtual Disks" is displayed when no free space left create VD.(SCGCQ01764540 port of SCGCQ01764049) 
 - Enhance the detailed help for Firmware download and get bios command.(SCGCQ01792109 port of SCGCQ01790167) 
 - Updating ncurses library from 6.0 to 6.1(SCGCQ01837234 port of SCGCQ01836749) 
 - Add get VPD command support to StorCLI in OS environment(SCGCQ01911298 port of SCGCQ01852603) 
 - perccli(007.0523.0000.0000 Jul 20, 2018(SCGCQ01914827 port of SCGCQ01874120) 
 - Incorrect Interface Details for "storcli /c0 show" command(SCGCQ01915785 port of SCGCQ01837612) 
 - Invader/Intruder: MR 6.13.1- PD FW download status help to be updated(SCGCQ01922838 port of SCGCQ01256727) 
 - Change in RAID levels displaying in controller show all command(SCGCQ01511611 port of SCGCQ01509578) 
 - Implemented to display the full Model number of the SATA drive when connected to an IT controller.(SCGCQ01528940 port of SCGCQ01525764) 
 - Storcli PR help execution delay is missing when PR running continuously(SCGCQ01537216 port of SCGCQ01534552) 
 - Application crashes while executing storcli64.exe /c0/dall set hidden=on(SCGCQ01599467 port of SCGCQ01571256) 
 - Un-supported command displayed for "storcli64.exe /call show sasaddress"(SCGCQ01620417 port of SCGCQ01619562) 
 - syntax error while executing "storcli64.exe /c0 get firmware ? "(SCGCQ01620453 port of SCGCQ01618675) 
 - Storcli does not display the complete enclosure serial number(SCGCQ01760661 port of SCGCQ01735493) 
 - PH9 PA StorCLI - Tape drive entry not seen at "Requested boot drive" field after set bootdrive on(SCGCQ01853459 port of SCGCQ01850418) 
 - Unified StorCLI : StorCLI doesn't display OS Name for Windows Server 2019 server(SCGCQ01869194 port of SCGCQ01867354) 
 - StorCLI should not display SED property when using IT-HBA(SCGCQ01915857 port of SCGCQ01589445) 
 - Unified StorCLI Phase 9: Prints are seen in the console when SL_GET_CTRL_INFO fails from SL in uEFI platform(SCGCQ01917167 port of SCGCQ01866548) 
 - Unconfigured Good PD is showing as belonging to Disk Group 0.(SCGCQ01525771 port of SCGCQ01520567) 
 - Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01526326 port of SCGCQ01526321) 
 - This feature is not supported on this Controller" is displayed multiple times.(SCGCQ01599446 port of SCGCQ01595717) 
 - Incremented devicename is programmed for all the phy's in IT controller(SCGCQ01599449 port of SCGCQ01548481) 
 - controller show all command is not listing the Battery information(SCGCQ01599459 port of SCGCQ01561689) 
 - Support only Dell SAS IT Controllers with PERCCLI(SCGCQ01618501 port of SCGCQ01547929) 
 - syntax error while executing "storcli64.exe /c0 get firmware ? "(SCGCQ01620437 port of SCGCQ01618675) 
 - Invalid return status from Storcli(SCGCQ01731842 port of SCGCQ01731797) 
 - Unified StorCLI LibMods 7.6 - Moving CLI's VIB toolchain to 6.0 and workbench to 3.5.7(SCGCQ01749416 port of SCGCQ01720952) 
 - DHS:Unable to add dedicated Hot Spare drive to specified DG.(SCGCQ01760603 port of SCGCQ01714443) 
 - Add Downgrade Firmware function in Storcli(SCGCQ01813396 port of SCGCQ01583223) 
 - Libmod changes for StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers - SCGCQ01775602(SCGCQ01853371 port of SCGCQ01775616) 
 - Unified StorCLI : StorCLI doesn't display OS Name for Windows Server 2019 server(SCGCQ01916018 port of SCGCQ01867354) 
 - Unconfigured Good PD is showing as belonging to Disk Group 0.(SCGCQ01525774 port of SCGCQ01520567) 
 - Spell error in /call/dall split mirror output.(SCGCQ01599466 port of SCGCQ01595709) 
 - Get VPD from MPB region is failure, but overalll status shows success(SCGCQ01599481 port of SCGCQ01589618) 
 - Compilation errors while compiling parser module(SCGCQ01600565 port of SCGCQ01600563) 
 - CLI does not report Serial number for Enclosure.(SCGCQ01714296 port of SCGCQ01595640) 
 - Unified StorCLI 7.6 - Moving CLI's VIB toolchain to 6.0 and workbench to 3.5.7(SCGCQ01745530 port of SCGCQ01720947) 
 - Updating the Diag results as per new API changes(SCGCQ01537265 port of SCGCQ01537255) 
 - Collecting snapdump through StorCli (Libmods(SCGCQ01594187 port of SCGCQ01589854) 
 - WWN for NVME PDs is reported as NA with MR(SCGCQ01749397 port of SCGCQ01731279) 
 - Unified StorCLI 7.7 : StorCLI should not issue SL_SET_LIB_PARAMETERS command(SCGCQ01758162 port of SCGCQ01676983) 
 - Spell mistake in error message for hwdev command(SCGCQ01760594 port of SCGCQ01614972) 
 - Error message-"Reached Maximum Supported virtual Disks" is displayed when no free space left create VD.(SCGCQ01764538 port of SCGCQ01760508) 
 - PERCCLI_PERC10.2-007.0512/When selecting a PD that is not configurable, it is showing "Atleast" which should be "At least"(SCGCQ01768422 port of SCGCQ01764929) 
 - StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers(SCGCQ01853405 port of SCGCQ01775602) 
 - Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01977760 port of SCGCQ01948579) 
 
EnhancementRequests
 - Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01473897) 
 - Adding JSON schema for Virtual Drive level commands(SCGCQ01516772) 
 - Enhance StorCLI show file= to include PnP ID(SCGCQ01517431) 
 - Need Storcli support drive FW upgrade(SCGCQ01583217) 
 - displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state"(SCGCQ01681538) 
 - Add ForceHCB option in StorCLI for IT controllers(SCGCQ01718946) 
 - Switch attached NVMe HW RAID support for Supermicro backplanes(SCGCQ01720819) 
 - Added customer serial number field to MFC Manufacturing 2 structure(SCGCQ01873417) 
 - MR API changes to support EKMS over OOB(SCGCQ01874035) 
 - Add new error code for tampered or invalid controller(SCGCQ01885686) 
 - Interrupt coalsecing setting per group of 8 replies queues (h/w VF registers(SCGCQ01886424) 
 - [MR 7.8] API change to export "disable least latency mode"(SCGCQ01887495) 
 - HDET: Support smp passthrough storeliboob (API changes requirement(SCGCQ01916035) 
 - Add secure boot key update complete event(SCGCQ01928254) 
 - Add Board Support Package Image Type to MR_IMAGE_TYPE(SCGCQ01931637) 
 - Support dynamically add/remove controller in Storelib IT for MCTP over PCIe(SCGCQ01934815) 
 - Fix MR_CTRL_INFO to support backward compatibility(SCGCQ01946548) 
 - Add a new log event used whenever the snap dump properties are modified.(SCGCQ01963328) 
 - Add a bit for atomic descriptor capable(SCGCQ01965047) 
 - Add Downgrade Firmware function in Storcli(SCGCQ01583223) 
 - Add support for TCG Opal 2.0 compliant SAS/SATA HDDs, SAS/SATA HDDs operations in StorCLI(SCGCQ01593849) 
 - StorCLI JSON 4.0 compliant schema creation for Phy (including mux and lane) level commands(SCGCQ01594119) 
 - Improve PERCcli Terminology When in eHBA Mode(SCGCQ01615487) 
 - UNMAP/TRIM/WRITESAME for NVMe devices for R0/1/EPD/JBOD(SCGCQ01727113) 
 - Adding JSON schema for Drive Group and Foreign configuration commands(SCGCQ01531269) 
 - Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01583226) 
 - Libmods : Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01615540) 
 - To add restriction on personality change requests from RAID to eHBA and eHBA to RAID(SCGCQ01721528) 
 - StorCLI JSON 4.0 compliant schema creation for Enclosure, BBU and CacheVault commands(SCGCQ01576130) 
 - Add get VPD command support to StorCLI in OS environment(SCGCQ01852603) 
 - Improve PERCcli Terminology When in eHBA Mode(SCGCQ01628424) 
 - Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ01761309) 


007.0525.0000.0000  - Moderate Impact/Low Probability of Occurrence
--------------------

Defects (16)
-.(SCGCQ01753405)
- Grammatical mistakes in Perccli Un-supported RAID level warning message.(SCGCQ01714033)
- Correcting the grammatical errors in firmware's MFI Stat messages.(SCGCQ01717315)
- Enclosure show status command gives success but nothing is shown.(SCGCQ01731280)
- One of the requirement for Criteo is to display JBOD-WB (EPD) to OS drive mapping.(SCGCQ01804763)
- Turn on the boodrive by storcli, HII does not reflect it, still shows "Off".(SCGCQ01816927)
- Incorrect Interface Details for "storcli /c0 show" command.(SCGCQ01837612)
- Two MCTP error codes in slerrors.h show same offset code 0x7098.(SCGCQ01627548)
- Space need in the output for secure erase.(SCGCQ01713604)
- seg fault is seen when when we try to generate CRC errors using megamon.(SCGCQ01841619)
- Missing punctuation in Perccli delete config message.(SCGCQ01698226)
- Personality Behavior Modes:Command returns failure when setting non-RAID behavior modes.(SCGCQ01713265)
- non-RAID:HII:CLI:Dedicated Hot Spare creation displays incorrect disk group association.(SCGCQ01698272)
- DHS:Unable to add dedicated Hot Spare drive to specified DG.(SCGCQ01714443)
- WWN for NVME PDs is reported as NA with MR.(SCGCQ01731279)
- Storcli: UEFI shell error display-Error: Unsupported File open Mode.(SCGCQ01837752)
- perccli /cx delete config command getting incorrect error message.(SCGCQ01851908 port of SCGCQ01850719)
- storclio need to support proprietary i2c controller mode.(SCGCQ01801679 port of SCGCQ01732990)
- State of the tape drive should be displayed as "JBOD" when FW state is MR_PD_STATE_SYSTEM.(SCGCQ01853457 port of SCGCQ01853444)
- Phase 7 - Drive Listing Is Not In Order for "/c0 show" & "/c0 show all".(SCGCQ01810054 port of SCGCQ01809355)
- storcli /cx/pall show command fails with older generation cards that does not support PCIe pages.(SCGCQ01758163 port of SCGCQ01520816)
- Unified StorCLI Phase 8 : NVMe and SAS Drive's WWN is incorrect for IT Controller.(SCGCQ01749927 port of SCGCQ01749795)
- storcli did not show current profile when connection in invalid config.(SCGCQ01760598 port of SCGCQ01713676)
- Storcli does not display the complete enclosure serial number.(SCGCQ01760655 port of SCGCQ01735493)
- Unified StorCLI 7.7 : StorCLI doesn't report failure status when nopad image flashing fails via completeflash command in MR.(SCGCQ01749921 port of SCGCQ01749849)
- Unified StorCLI 7.7 : Unconfigured BAD drives are not displayed in /c0 show output.(SCGCQ01718294 port of SCGCQ01718269)
- "Cached Virtual Drives" displayed in /c0/dall show cachecade without the table.(SCGCQ01760676 port of SCGCQ01537017)
- controller show wbsupport reason is not listed in the cli output.(SCGCQ01760590 port of SCGCQ01561704)
- Updating ncurses library from 6.0 to 6.1.(SCGCQ01837234 port of SCGCQ01836749)
- Drive Listing Is Not In Order for "/c0 show" & "/c0/eall/sall show".(SCGCQ01732928 port of SCGCQ01714356)
- Storcli does not display the complete enclosure serial number.(SCGCQ01760661 port of SCGCQ01735493)
- Unified StorCLI : StorCLI doesn't display OS Name for Windows Server 2019 server.(SCGCQ01869194 port of SCGCQ01867354)
- PH9 PA StorCLI - Tape drive entry not seen at "Requested boot drive" field after set bootdrive on.(SCGCQ01853459 port of SCGCQ01850418)
- Libmod changes for StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers - SCGCQ01775602.(SCGCQ01853371 port of SCGCQ01775616)
- Add Downgrade Firmware function in Storcli.(SCGCQ01813396 port of SCGCQ01583223)
- Spell mistake in error message for hwdev command.(SCGCQ01760594 port of SCGCQ01614972)
- StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers.(SCGCQ01853405 port of SCGCQ01775602)
- Unified StorCLI 7.7 : StorCLI should not issue SL_SET_LIB_PARAMETERS command.(SCGCQ01758162 port of SCGCQ01676983)

EnhancementRequests (30)
- API Changes for Driver/FW DCMD HandShake.(SCGCQ01841266)
- RTTrace Enable/Disable API changes.(SCGCQ01830211)
- Criteo: API changes reversal.(SCGCQ01760512)
- RTTrace API Changes.(SCGCQ01745568)
- API changes needed to support eHBA product series.(SCGCQ01727346)
- Create sanitize events.(SCGCQ01713708)
- MPI 2.5: Add MaxEnclosureLevel field to BIOS Page 1.(SCGCQ01570730)
-.(SCGCQ01593479)
-.(SCGCQ01761309)
- displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state".(SCGCQ01681538)
- API change for Switch attached NVMe HW RAID support for Supermicro backplanes.(SCGCQ01697667)
- Mixing Rules for SED and non-SED drives to create non-secure array with controller security enabled.(SCGCQ01757538)
- Unmap: Define new API for enhanced UNMAP support.(SCGCQ01758062)
- Adding API bit to indicate whether forced personality change is supported or not.(SCGCQ01762153)
- Unmap: Define new events for enhanced UNMAP support [MR7.8].(SCGCQ01803319)
- Deprecate the snap dump fields that are no longer needed for MR_SNAP_DUMP_PROPERTIES structure.(SCGCQ01816724)
-.(SCGCQ01818580)
- Add the API to clear all the snap-dumps from firmware.(SCGCQ01824135)
- API change to provide learn complete timestamp.(SCGCQ01845269)
- Added Support for Triggering SnapDump.(SCGCQ01848759)
- Add secure boot support.(SCGCQ01792416)
- Improve PERCcli Terminology When in eHBA Mode.(SCGCQ01615487)
- Including The Time Stamp for every Snap Dump created in the firmware.(SCGCQ01797424)
- Aero FW - Reporting SSD wear gauge values for OEM specific customers.(SCGCQ01798686)
- [MR 7.8] API change to return apt failure status for a personality change request.(SCGCQ01853480)
- Added new events for unmap policy changes.(SCGCQ01871912)
- MPI 2.5: Add OEMRD field to SAS Enclosure Page 0.(SCGCQ01553021)
- API Changes - After Vision PSOC FW update, applications should ask the user for power cycle instead of reboot.(SCGCQ01765150)
- To add restriction on personality change requests from RAID to eHBA and eHBA to RAID.(SCGCQ01721528)
- Add get VPD command support to StorCLI in OS environment.(SCGCQ01852603)


0007.0507.0000.0000-1 - Moderate Impact/Low Probability of Occurrence
-------------------

Defects (75)
- Profile Mgmt API Changes.( SCGCQ00883008)
- MR_RAID_CTX_G35 has one too many bits.(SCGCQ00886417)
- Reintroduce numSGEExt Field in Raid Context for Invader to support 1MB IO.(SCGCQ00927738)
- The code had events with repetitive ID and some structures clashing.(SCGCQ00948535)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23.(SCGCQ01001936)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23 has been added back again into adapteroperations 4.(SCGCQ01014835)
- 800C error when execting Get MFC default function.(SCGCQ01037840)
- Enable WB support via API.(SCGCQ01405242)
- Storcli: Instance Validation Failed between "controller-properties-schema.json" and "show" json..(SCGCQ01413239)
- Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON..(SCGCQ01423458)
- Port linkspeed is displayed in a different JSON object for NVMe drives.(SCGCQ01436920)
- Remove unsupported Ethernet code for IT controller from CLI.(SCGCQ01448979)
- Show command is not processed for IT firmware and IT complete flash images in big endian server.(SCGCQ01451940)
- storcli /c0/e123/s1 show poh shows drive info on IT controller.(SCGCQ01456171)
- Storcli displays "success" and "failure" both when trying to enable UNMAP on RAID5 using SSDs..(SCGCQ01462396)
- Storcli verbose help for Unmap has spelling mistakes.(SCGCQ01462401)
- Updating the JSON Schema for the SCSI Unmap feature.(SCGCQ01465745)
- Storcli: Instance Validation Failed between "system-schema.json" and "show" JSON..(SCGCQ01467131)
- Part 1 : Fixing coverity issues - Resource leaks and Illegal comparison.(SCGCQ01470420)
- Instance Validation Failed between "virtual-drive-config-schema.json" and "add vd " JSON.(SCGCQ01471852)
- Start/Stop locate on a invalid enclosure returns success.(SCGCQ01480910)
- Detailed help contents were not present for most of the IT download options..(SCGCQ01483760)
- Spelling errors in the "/cx restart" command..(SCGCQ01486415)
- Storcli: Instance Validation Failed between "controller-flash-component-erase-schema.json" and "flasherase" JSON..(SCGCQ01506022)
- Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show_profile" JSON..(SCGCQ01506052)
- CLI help does not reflect the new command to create an ePD.(SCGCQ01639583)
- Phase3 Beta PCIe: Loading SLOOB fails with error message "ExitLib failed for SAS IT Controller!! rval 0x801A".(SCGCQ01292964)
- Instance Validation is failing for mentioned commands..(SCGCQ01415355)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show all" JSON output..(SCGCQ01423447)
- Incorrect PNP ID format is displayed in EFI for firmware and complete flash images.(SCGCQ01448990)
- PH6 Ventura Pre-Alpha - StorCLI - "show file = fw.bin" command usage is not updated in help.(SCGCQ01460588)
- Showing empty error msg in CLI when Unmap not supported is returned by FW..(SCGCQ01464580)
- Storcli: Instance Validation Failed between "enclosure-schema.json" and "/call/eall show" JSON..(SCGCQ01467146)
- Storcli: Instance Validation Failed between "jbod-show-schema.json" and "/call/jbodall show" JSON..(SCGCQ01467694)
- PH6 Ventura Pre-Alpha - StorCLI - /c0 show all - Capabilities for supported drives seen only SAS/SATA, NVMe not found.(SCGCQ01480920)
- PH6 Ventura - Storcli crashed in Win2016 when "storcli64.exe J" is executed.(SCGCQ01488062)
- Instance Validation Failed between "controller-termlog-schema.json" and "set termlog=off" JSON..(SCGCQ01506041)
- Readme file have no mention of PD and JBOD level command support..(SCGCQ01507421)
- Checking in VBAS compliation changes.(SCGCQ01630324)
- PERCCLI ePD personality behavior command is still an available option and has not been removed.(SCGCQ01639798)
- Storcli: VD creation fails from storcli in presence of 0KB bad drive.(SCGCQ01713240)
- Operating system is not displaying the version in EFI for any of command in cli.(SCGCQ01410613)
- Instance Validation Failed between "controller-ASO-schema.json" and "show ASO" json.(SCGCQ01430237)
- Updating pre-ventura SBR fails with "hwdevice" command.(SCGCQ01438214)
- MR7.5: StorCLI reports Multipath ON during set but OFF during show commands.(SCGCQ01440234)
- Adding excludevd option to the help file of patrolread command.(SCGCQ01443435)
- PH6 Ventura Pre-Alpha - StorCLI - /cx/ set bootdrive = on/off command not updated in help page.(SCGCQ01460582)
- Schema addition for "show file=" command.(SCGCQ01461209)
- PH6 Ventura Pre-Alpha -- "storcli64.exe /c0 compare ssid ver = 2 J" command crashes and utility stopped working in Win2016.(SCGCQ01462593)
- MR 7.5_UNMAP : UNMAP support info is not shown in controller supported operations and VD properties.(SCGCQ01464562)
- PH6 Ventura StorCLI - Pre-Alpha - /cx compare detailed help is not giving complete information.(SCGCQ01464762)
- Instance Validation Failed between "controller-patrolread-set-schema.json" and "/c0 set pr excludevd=1" JSON.(SCGCQ01472845)
- Instance Validation Failed between "drive-operations-patrolread-schema.json" and "/call/e65/sall show patrolread".(SCGCQ01473344)
- Grammatical error in Perccli warning message during FW Flash.(SCGCQ01686670)
- OpROM's and their versions are not displayed for 8,32,and 64 MB IT complete flash images.(SCGCQ01449785)
- Part 3 : Fixing coverity issue : Resource leaks.(SCGCQ01472797)
- Storcli: Instance Validation Failed between schema and JSON output for many scenarios with one common error.(SCGCQ01506038)
- Reverting back SL_MAX_OS_DRIVE_COUNT value to 300.(SCGCQ01114306)
- Assign VDs suboption in cachecade VD creation is not assigning the intended VDs.(SCGCQ01419754)
- Incorrect help description for erase and download completeflash commands.(SCGCQ01470263)
- Instance Validation Failed between "controller-jbod-schema.json" and "add jbod" JSON..(SCGCQ01472802)
- Storcli: Instance Validation Failed for direct attached drive commands..(SCGCQ01472833)
- Check for supported pages for firing drive SCSI commands.(SCGCQ01474325)
- No error description when start/stop locate fails on the drive from StoreLIBIT library.(SCGCQ01480900)
- IT command to set sasadd and other set operations shows success for an MR controller.(SCGCQ01483753)
- Changing CV/BBU state algorithm according to the updated design document..(SCGCQ01388595)
- DriveID and errormsg are coming improper on drive POH command when failed.(SCGCQ01443683)
- Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" json..(SCGCQ01465446)
- Coverity libmods issues - Resource leaks and Wrong sizes.(SCGCQ01472195)
- Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/eall/sall show all" json..(SCGCQ01473334)
- Unified StorCLI does not support erasing of persistent config pages in host for IT controllers.(SCGCQ01466766)
- Storcli: Instance Validation Failed between "jbod-show-schema.json" and "/c0/jbodx show" JSON..(SCGCQ01472821)
- UEFI StorCLI should detect controller when UEFI driver is not present and when FW is in ready state.(SCGCQ01489472)
- The structure name is changed from oob_i2c to oob to avoid compilation failure in OOB SL.(SCGCQ01015024)
- Instance Validation Failed between "controller-freespace-schema.json" and "show freespace" JSON output..(SCGCQ01414749)


EnhancementRequests (174)
- MPI2: Add TargetModeAbort by initiator device handle.(SCGCQ00337167)
- New fault code for routine synchronous reset.(SCGCQ01264142)
- MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually.(SCGCQ00574358)
- MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag).(SCGCQ00414050)
- MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply.(SCGCQ00396414)
- MPI2: Add OEM Identifier to BIOS Page 1.(SCGCQ00357228)
- MPI2: Use Slot Information during Port Enable Event Replay option.(SCGCQ00356796)
- MPI2: Add new TargetModeAbort AbortType to only abort Command IUs.(SCGCQ00345215)
- MPI v2.6: Additional request and reply descriptor formats.(SCGCQ00259613)
- Modify event string APIs for MISSING and OFFLINE LDs.(SCGCQ01628177)
- New configuration params added for EPD-PT devices.(SCGCQ01599607)
- MR API change request to Enable/disable the parallel PD FW update feature based on PNP ID’s.(SCGCQ01595347)
- Implement Snapdump debugging capability.(SCGCQ01567770)
- Add "Incompatible with Profile" event.(SCGCQ01289924)
- API changes for CR55 - PCIe lane/link speed.(SCGCQ01222700)
- API change for Simplified RAID10 Creation.(SCGCQ01222698)
- API Changes Required for Specific OEM Backplane functionality.(SCGCQ01218406)
- API changes for PR SCGCQ01139678 - Method for determining bad ONFI flash in storcli.(SCGCQ01215334)
- MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0.(SCGCQ01213028)
- MPI 2.5: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01208954)
- API changes for PR SCGCQ01127742 - Isolating faulty cable issue from bad drive issue.(SCGCQ01203751)
- MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP.(SCGCQ01180886)
- MR 6.12 - Add JBOD mode personality to MR_CTRL_PERSONALITY.(SCGCQ01146597)
- MR 7.0: Add supportPdMapTargetId flag in MR_CTRL_INFO and MFI_CAPABILITIES.(SCGCQ01141251)
- MR 6.13: Add API support for TFM/SCAP _MR_BBU_VPD_INFO_FIXED parameters.(SCGCQ01139344)
- MR 6.13: Add a new control command to fetch ROC temperature data over I2C.(SCGCQ01137627)
- MR 7.2: Add API support to make application work with Cachecade3.0 on Ventura (Public).(SCGCQ01114969)
- MPI 2.5: Add new connector types.(SCGCQ01085073)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ01002367)
- MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout".(SCGCQ00996127)
- MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1.(SCGCQ00853162)
- MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable.(SCGCQ00791885)
- MPI 2.5: add WWID to BIOS Page 3.(SCGCQ00785208)
- MPI 2.5: update copyright info.(SCGCQ00728066)
- MPI 2.5: BIOS Page 1 additions.(SCGCQ00700829)
- MPI 2.5: distribute Target Command Buffers Received across multiple reply queues.(SCGCQ00685820)
- MPI 2.0: Add product-specific Flag bit to Clean Tool.(SCGCQ00569175)
- Add type BIOS for HashImageType..(SCGCQ00566306)
- Identify physical location of a target device.(SCGCQ00523879)
- MPI 2.5: add reserved fields to IO Unit Page 7 for future use.(SCGCQ00477817)
- MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps".(SCGCQ00471293)
- MPI 2.5: Signed images for FWDownload.(SCGCQ00469990)
- MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL.(SCGCQ00438437)
- MPI 2.5: Toolbox Console Text Display Tool.(SCGCQ00415512)
- Allow Protection Information bit for IR Volume Create.(SCGCQ00385306)
- MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply.(SCGCQ00357551)
- MPI 2.6: add PCIe Device Config Pages.(SCGCQ00345271)
- MPI 2.6: PCIe Switch Config Pages.(SCGCQ00345270)
- MPI 2.6: PCIe Topology Change List Event.(SCGCQ00345266)
- MPI 2.6: add PCIe Event Data (Generic), PCIe Device Status Change Event, and PCIe Enumeration Event.(SCGCQ00345260)
- MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors.(SCGCQ00338506)
- MPI 2.6: PCIe IO Unit Page 0 & 1 definitions.(SCGCQ00336383)
- MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1.(SCGCQ00310439)
- MPI 2.6: update SGL chapter to include PCIe.(SCGCQ00294131)
- MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request.(SCGCQ00294055)
- MPI 2.6: NVMe Encapsulated request.(SCGCQ00264759)
- MPI 2.6: SOP Encapsulated request.(SCGCQ00264755)
- Improve PERCcli Terminology When in eHBA Mode.(SCGCQ01615487)
- JSON schema for Drive level commands.(SCGCQ01445435)
- MPI 2.6 Add Atomic Request Descriptor capability.(SCGCQ00227735)
- MPI 2.6: add IO Unit Control Request.(SCGCQ00345258)
- MPI 2.6: PCIe Link Config Pages.(SCGCQ00345272)
- MPI 2.6: Enclosure Management.(SCGCQ00345273)
- Device Info field for PCIe devices.(SCGCQ00353339)
- MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request.(SCGCQ00360843)
- MPI 2.6: new family values for ProductID fields.(SCGCQ00360952)
- MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11.(SCGCQ00363600)
- Modified address space bits.(SCGCQ00397136)
- MPI 2.6: Add PCIe IO Unit Page 4.(SCGCQ00397563)
- MPI 2.6: Add board power fields to IO Unit Page 7.(SCGCQ00397572)
- MPI 2.6: Add support for SAS Persistent Connections.(SCGCQ00397577)
- MPI 2.6: Add NVMe SGL support.(SCGCQ00398256)
- MPI 2.6: Add NVMe SGL support to IEEE SGL.(SCGCQ00432541)
- MPI 2.6: System Interface Register Set update.(SCGCQ00464402)
- Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request.(SCGCQ00480292)
- MPI 2.6: shutdown operation for IO Unit Control Request.(SCGCQ00496998)
- MPI 2.6: Add supported link rates and widths for PCIe devices.(SCGCQ00564281)
- MPI 2.6: Add additional NVMe AccessStatus codes.(SCGCQ00574070)
- MPI 2.6: Add BootFlags field to Firmware Image Header.(SCGCQ00601869)
- MPI 2.6: Add new FLASH region types.(SCGCQ00619371)
- MPI 2.6: Added an additional signature value for the firmware image header.(SCGCQ00623271)
- MPI 2.6: additional AccessStatus values for PCIe Device Page 0.(SCGCQ00664957)
- MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages.(SCGCQ00680527)
- MPI 2.6: Extend Task Management - Target Reset Method to include PCIe devices.(SCGCQ00686666)
- MPI 2.6: Add device off flag to SCSI Enclosure Processor messages.(SCGCQ00776177)
- MPI 2.6: New Phy event codes added to Ventura.(SCGCQ00789600)
- MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough.(SCGCQ00813389)
- MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura.(SCGCQ00827088)
- MPI 2.6: add PCI Device ID's.(SCGCQ00828497)
- MPI 2.6: methods to report Active Cable power problems.(SCGCQ00831588)
- MPI 2.6: SRIOV support for PCIe devices.(SCGCQ00852827)
- MPI 2.6: Update Flash Signature..(SCGCQ00852831)
- profile management API.(SCGCQ00867953)
- MPI 2.6: add new feature to control NVMe SGL format.(SCGCQ00872169)
- Mega API modifications needed for RMW-FP and Cache bypass features in Ventura.(SCGCQ00875328)
-.(SCGCQ00878757)
- Merging api_overrides mega_api files with the files in the Mega_API development stream.(SCGCQ00883262)
- MPI 2.6: Update Ventura family device ids to match latest EDS.(SCGCQ00915256)
- MPI 2.6: update Marlin-class device IDs.(SCGCQ00915336)
- MPI 2.6: Remove all SOP references.(SCGCQ00925839)
- Ventura: de-feature AHCI.(SCGCQ00941620)
- MPI 2.6: Remove all AHCI references.(SCGCQ00948258)
- MPI 2.6: Add support for SAS-4 and PCIe-4.(SCGCQ00948955)
- MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0.(SCGCQ00949638)
- MPI 2.6: add LinkNum field to the PCIe Link configuration pages.(SCGCQ00954619)
-.(SCGCQ00987840)
- MPI-2.6: backend PCIe feature initialization status reporting.(SCGCQ01009104)
- MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request.(SCGCQ01013930)
- MPI2.6: Fix defines that are not unique within the first 32 characters.(SCGCQ01015826)
- MPI 2.6: direct reporting of negotiated PCIe link width and speed.(SCGCQ01017027)
- MPI 2.6: Backend SRIS mode enable flag.(SCGCQ01018687)
- MPI2.6: Reserve ExtPageTypes for Dragon.(SCGCQ01020473)
- MR_CTRL_INFO expansion from 2K to 4K.(SCGCQ01023741)
- mega api changes for ibuttonless PR.(SCGCQ01059740)
- MPI2.6: Add x16 PCI support for Marlin family products.(SCGCQ01063009)
- MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page.(SCGCQ01071374)
- Profile Management Changes to support requestedProfileID and optimisedProfile.(SCGCQ01075821)
-.(SCGCQ01082303)
-.(SCGCQ01085954)
- MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout".(SCGCQ01092340)
- MEGA_API Changes to incorporate new IO subtype to support redirect cached IO.(SCGCQ01094549)
- MPI 2.6: Add Sea Arch class and Product IDs.(SCGCQ01116837)
- MR 7.0: Add MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT = 7 to mfi.h file.(SCGCQ01133839)
- MPI2.6: Added new image type and flash region definitions.(SCGCQ01136127)
- MPI 2.6: Add new clean tool options.(SCGCQ01141732)
- MPI 2.6: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01146583)
- Define CurrentFwNvmePageSize element in new MFI_REG_STATE_EXT3 register.(SCGCQ01188725)
- MR7.1. Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01213092)
- MPI2.6: Mfg7 support for arbitrary starting slot number.(SCGCQ01213267)
- Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01216848)
- MPI 2.6: Add new firmware download type (CBB BACKUP).(SCGCQ01258005)
- MPI 2.6: Add new firmware download type (CPLD IMAGE).(SCGCQ01305760)
- MPI 2.6: add NVMe SGL Data Block descriptor alignment flag.(SCGCQ01339864)
- MPI 2.6: Add Aero PCI Device IDs.(SCGCQ01373008)
-.(SCGCQ01389581)
- MPI 2.6: Add ControllerResetTO to PCIe Device Page 2.(SCGCQ01416498)
- MPI 2.6: Add new reason code to PCIE Device Status Change Event.(SCGCQ01416515)
- Add Test Link Diagnostic API.(SCGCQ01436268)
- Add a new structure to provide OEMs ability to switch to select either I2C or PCIe as an out of band transport.(SCGCQ01445048)
- MPI 2.6: PCIe Device Page 2 reporting Namespace Optimal IO Boundary(NOIOB) for NVMe devices.(SCGCQ01449138)
- Provide OEMs ability to select either I2C or PCIe as an out of band transport.(SCGCQ01450245)
- Update description of MR_DCMD_CTRL_PERSONALITY_SET Dcmd.(SCGCQ01467149)
- Added MR_MFC_DEFAULTS.NVMeAbortTO and MR_MFC_DEFAULTS.NVMeMaxControllerResetTO.(SCGCQ01532045)
- Add support for API fields to report SED type of PD.(SCGCQ01587230)
- Add OnOff parameter in Properties2 of Structure MR_CTRL_PROP to enable/disable mix of Enterprise & Opal SED drives.(SCGCQ01593520)
- NVDATA parameter to OPAL SED.(SCGCQ01614689)
- Added a new interface between driver-aops to indicate if 64 bit SGL support is enabled.(SCGCQ01620350)
- Add new MFI Status to block requested operation due to existing controller configuration.(SCGCQ01670135)
- Change the mr.h API comment showing the new return status for the - MR_DCMD_PD_GET_INFO.(SCGCQ01670234)
- Add support to defeature Cached I/O policy.(SCGCQ01581032)
- New events for PR/CC conflicts and sector size mismatch.(SCGCQ01227051)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ00988360)
- MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses.(SCGCQ00466819)
- Removing the NMR storcli commands from storcli..(SCGCQ01445268)
- Add support to allow Device names greater than 107.(SCGCQ01039328)
- MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs.(SCGCQ00397568)
- MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit.(SCGCQ00884740)
- MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks.(SCGCQ00922213)
- MPI 2.6: Device side PCIe SRNS flag.(SCGCQ01276256)
- Checking of VBAS make file DataPro of Univ_viva_libmods.(SCGCQ01488176)
- Profile Management: Storcli - Add support for WB bit in profile management show.(SCGCQ01445628)
- Removing the NMR storcli commands from storcli..(SCGCQ01445418)
-.(SCGCQ01428114)
-.(SCGCQ01423509)
- Provide end-user ability to select either I2C or PCIe as an out of band transport.(SCGCQ01452987)
- Add NVMe device related changes.(SCGCQ01034678)
- Provide end-user ability to select either I2C or PCIe as an out of band transport.(SCGCQ01452986)
- Add boot drive selection support in Stor-CLI.(SCGCQ01445896)
- Improve PERCcli Terminology When in eHBA Mode.(SCGCQ01628424)
-.(SCGCQ01466805)
- StorCLI Libmods - Ventura LD de-allocation support on SAS/SATA SSDs through UNMAP/WRITE SAME on non-PARITY, non-DIF.(SCGCQ01448954)
- StorCLI - Ventura LD de-allocation support on SAS/SATA SSDs through UNMAP/WRITE SAME on non-PARITY, non-DIF volumes.(SCGCQ01447799)
- Adding JSON schema for JBOD and Drive level commands.(SCGCQ01445308)
- Add support for IT Firmware images and IT Completeflash images to "show file=" command.(SCGCQ01436882)

CSETActivities (57)
- StorCLI should not display SED property when using IT-HBA.(SCGCQ01600142 port of SCGCQ01589445)
- Enumeration of drives in NGM[PERCCLI Implementation / HBA330 Mini Mezz](SCGCQ01600137 port of SCGCQ01458174)
- Allow "noreset" option for IT controllers during firmware download.(SCGCQ01599545 port of SCGCQ01514483)
- Storcli show displays OS Version appended with Technical Preview.(SCGCQ01478448 port of SCGCQ01474457)
- Storcli: Instance Validation Failed between "controller-cc-schema.json" and "show consistencycheck" JSON(SCGCQ01456168 port of SCGCQ01451170)
- Phase 5 : Command "storcli /c0 show all" crashes with drives connected to SAS3.5 IT controller(SCGCQ01452992 port of SCGCQ01452982)
- Instance Validation Failed between "controller-ASO-schema.json" and "show ASO" json(SCGCQ01430285 port of SCGCQ01430237)
- SLT : Requesting user to enter the allocated response length of SMP request page(SCGCQ01202087 port of SCGCQ01202030)
- Changing ini file name to storelibconfit.ini(SCGCQ01275669 port of SCGCQ01275496)
- Unified StorCLI 7.6 : Creation of VD aborts StorCLI when FW returns error code for MR_DCMD_CFG_READ DCMD(SCGCQ01600150 port of SCGCQ01588245)
- This feature is not supported on this Controller" is displayed multiple times(SCGCQ01599461 port of SCGCQ01595717)
- Storcli may not be able to show the RAID controller in some special situation(SCGCQ01500340 port of SCGCQ01392154)
- Port linkspeed is displayed in a different JSON object for NVMe drives(SCGCQ01438288 port of SCGCQ01436920)
- Changing ini file name to storelibconfit.ini(SCGCQ01275670 port of SCGCQ01275496)
- Cutlass Phase 16 Storcli: Partner device ID should be suppressed under ./storcli /c0/eall show for multipath connections(SCGCQ01625114 port of SCGCQ01606780)
- Support only Dell SAS IT Controllers with PERCCLI(SCGCQ01618493 port of SCGCQ01547929)
- Storcli_Aero: Storcli not able to detect controller at EFI shell without Avago MR driver(SCGCQ01600151 port of SCGCQ01595698)
- Storcli returns error for show file commands when parsing MR images eventhough the command was successful(SCGCQ01600149 port of SCGCQ01529009)
- Detailed status is not displayed on locating a drive which is not connected to IT card(SCGCQ01599519 port of SCGCQ01571154)
- storcli controller show all lists EPD's in VD list(SCGCQ01599486 port of SCGCQ01556595)
- Spell error in /call/dall split mirror output(SCGCQ01599464 port of SCGCQ01595709)
- Unified StorCLI 7.6 : Read SBR fails with pre-ventura controllers(SCGCQ01539390 port of SCGCQ01539360)
- Implemented to display the full Model number of the SATA drive when connected to an IT controller(SCGCQ01528939 port of SCGCQ01525764)
- Libmod: checking-in the changes forLibmods for SCGCQ01525764(SCGCQ01528935 port of SCGCQ01528886)
- Storcli display Operating System without space for Linux version(SCGCQ01479250 port of SCGCQ01478526)
- Adding excludevd option to the help file of patrolread command(SCGCQ01445710 port of SCGCQ01443435)
- Updating readme file(SCGCQ01294583 port of SCGCQ01294570)
- SLT displays XYRATEX enclosure many fields information as "Unsupported", when we fire a command Get Enclosure Status(SCGCQ01003523 port of SCGCQ00950453)
- Libmod Changes for Defect SCGCQ01595640 (CLI does not report Serial number for Lenovo D1224 Enclosure)(SCGCQ01714307 port of SCGCQ01664412)
- Storcli_Aero: unable to set sasadd methodport on IT controller(SCGCQ01628094 port of SCGCQ01609234)
- Update help contents for jbod delete(SCGCQ01625945 port of SCGCQ01624605)
- Un-supported command displayed for "storcli64.exe /call show sasaddress"(SCGCQ01620412 port of SCGCQ01619562)
- Commands "/call/all" return inappropriate message or segfault when both MR and IT controllers are connected(SCGCQ01599483 port of SCGCQ01561703)
- Profile Management: Storcli - Add support for WB bit in profile management show(SCGCQ01454856 port of SCGCQ01445628)
- Instance Validation is failing for mentioned commands.(SCGCQ01445724 port of SCGCQ01415355)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show all" JSON output.(SCGCQ01436736 port of SCGCQ01423447)
- Application crashes while executing storcli64.exe /c0/dall set hidden=on(SCGCQ01599467 port of SCGCQ01571256)
- Storcli PR help execution delay is missing when PR running continuously(SCGCQ01537216 port of SCGCQ01534552)
- Change in RAID levels displaying in controller show all command(SCGCQ01511611 port of SCGCQ01509578)
- Upgrading the ncurses library from 5.4 to 6.0 in view of security vulnerabilities(SCGCQ01500111 port of SCGCQ01499900)
- DriveID and errormsg are coming improper on drive POH command when failed(SCGCQ01447688 port of SCGCQ01443683)
- Instance Validation Failed between "controller-freespace-schema.json" and "show freespace" JSON output.(SCGCQ01430044 port of SCGCQ01414749)
- syntax error while executing "storcli64.exe /c0 get firmware ? "(SCGCQ01620437 port of SCGCQ01618675)
- controller show all command is not listing the Battery information(SCGCQ01599459 port of SCGCQ01561689)
- Incremented devicename is programmed for all the phy's in IT controller(SCGCQ01599449 port of SCGCQ01548481)
- Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01526326 port of SCGCQ01526321)
- Unified StorCLI 7.0.1 : Programming VPD to MPB regions(SCGCQ01500006 port of SCGCQ01336460)
- Unified StorCLI 7.0.1 : Programming VPD to MPB regions(SCGCQ01500000 port of SCGCQ01336460)
- Instance Validation Failed between "controller-properties-schema.json" and "show" json output.(SCGCQ01452142 port of SCGCQ01451156)
- Updating pre-ventura SBR fails with "hwdevice" command(SCGCQ01438351 port of SCGCQ01438214)
- CLI does not report Serial number for Enclosure.(SCGCQ01714296 port of SCGCQ01595640)
- Get VPD from MPB region is failure, but overalll status shows success(SCGCQ01599481 port of SCGCQ01589618)
- Unconfigured Good PD is showing as belonging to Disk Group 0.(SCGCQ01525774 port of SCGCQ01520567)
- Controller should not be reset after firmware download in CLI for SAS 3.5 Controllers(SCGCQ01500132 port of SCGCQ01399793)
- Updating the Diag results as per new API changes(SCGCQ01537265 port of SCGCQ01537255)
- Storcli show preservedcache displays incorrect VD size on a missing VD(SCGCQ01500316 port of SCGCQ01447792)
- Assign VDs suboption in cachecade VD creation is not assigning the intended VDs.(SCGCQ01456036 port of SCGCQ01419754)

0007.0409.0000.0000- Moderate Impact/Low Probability of Occurrence
-------------------
fixes:
- Profile Mgmt API Changes.(SCGCQ00883008)
- MR_RAID_CTX_G35 has one too many bits.(SCGCQ00886417)
- Reintroduce numSGEExt Field in Raid Context for Invader to support 1MB IO.(SCGCQ00927738)
- The code had events with repetitive ID and some structures clashing.(SCGCQ00948535)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23.(SCGCQ01001936)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23 has been added back again into adapteroperations 4.(SCGCQ01014835)
- 800C error when execting Get MFC default function.(SCGCQ01037840)
- StorCLIO states wrong OS version for Windows 2016.(SCGCQ01274715)
- PH4 StorCLI -Cutlass-9305-16e FW download failed on Linux/Windows OS platforms.(SCGCQ01311728)
- Erase [excludemfg] file=<> command hangs when executed on non-op/jumpered/OCR disabled operational MR Ventura controllers.(SCGCQ01311846)
- Fixing Error Handling issues and Resource leak.(SCGCQ01319395)
- Fix for Libmod files having potential loop errors.(SCGCQ01320336)
- Cisco - CSCvd90485 - StorCLI error message incorrect when disabling LargeIO support.(SCGCQ01322003)
- EFIStorcli(1.21.12):Number of blocks in VD info is blank when queried for VD info from EFIStorcli.(SCGCQ01355452)
- Factory command is deducting the remanfacturing license even for the first time manufacturing.(SCGCQ01364604)
- Updated the Help.(SCGCQ01375059)
- controller show all command is not listing the JBODs when controller is in JBOD personality.(SCGCQ01383816)
- Controller mode reported as "Undefined" in JBOD mode in show profile output.(SCGCQ01384238)
- storcli is giving error when issuing the command dall show mirror.(SCGCQ01384690)
- Misleading message "Reboot" when erase or completeflash done in MR ventura.(SCGCQ01385373)
- storcli craches with drive show all command for some specific SATA drive.(SCGCQ01385425)
- Fixing out of bounds in libmods.(SCGCQ01385430)
- StorCli should display 128 byte inquiry for drives connected to IT controller including tape.(SCGCQ01388177)
- Save and restore with spanned volumes is throwing an error array index invalid.(SCGCQ01388543)
- PH5 StorCLI - Pre-Alpha - Show all reports NVMe drive linkspeed as "UNKNOWN".(SCGCQ01392511)
- Strocli: controller-shutdown-restart-schema.json is not in JSON format.(SCGCQ01412756)
- Storclio and storclif dispays windows version wrong for Windows 10 OS.(SCGCQ01413011)
- Storcli: Instance Validation Failed between "controller-sgpioforce-schema.json" and "set sgpioforce" JSON output.(SCGCQ01413017)
- Storcli: Instance Validation Failed between "controller-properties-schema.json" and "show" json.(SCGCQ01413239)
- Not even or regular in pattern of drive order display in storcli.(SCGCQ01415875)
- Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON.(SCGCQ01423458)
- Port linkspeed is displayed in a different JSON object for NVMe drives.(SCGCQ01436920)
- PERC10 - VD is deleted after discarding preserved cache with CLI.(SCGCQ01300897)
- Need to handle FW return code change for profile management success case.(SCGCQ01307320)
- Unified StorCLI 7.3 : Fixing resource leaks - Part 1.(SCGCQ01319405)
- PH4 Ventura PA - StorCLI - show command prints wrong information for Fury C0 in OEL6.8.(SCGCQ01321477)
- Non-operational state of FW when EFI driver is absent causing segmentation fault.(SCGCQ01324749)
- CLI reports failure when issuie DPM commands.(SCGCQ01333085)
- PH4 Ventura - StorCLI - Indentation errors observed in output while programming invalid length VPD file.(SCGCQ01346041)
- Fixing unchecked return values.(SCGCQ01385377)
- Tape drive connected to MR controller should not take NVMe speeds in to consideration.(SCGCQ01388610)
- Battery Capacitance is displayed incorrectly across different applications.(SCGCQ01389922)
- LinkSpeed is unknown for PCIe devices under Port Information headline.(SCGCQ01404583)
- Storcli: Instance Validation Failed between "controller-eghs-schema.json" and "set eghs" JSON output.(SCGCQ01412764)
- Storcli: Instance Validation Failed between "controller-securitykey-schema.json" and "set securitykey" JSON output.(SCGCQ01412948)
- Storcli: Instance Validation Failed between "controller-time-schema.json" and set time json.(SCGCQ01413222)
- This is a syntactical error where a comma was added.(SCGCQ01414744)
- Storcli: Additional string displayed in "Show wbsupport" output.(SCGCQ01415208)
- Instance Validation is failing for mentioned commands.(SCGCQ01415355)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show all" JSON output.(SCGCQ01423447)
- Second OCR request not getting triggered, fired when first OCR request about to finish, but O/P shows success.(SCGCQ01290216)
- StorCLI - Show command thorws error "failed to get information from host" in APM (ARM) CentOS.(SCGCQ01321460)
- Unified StorCLI 7.3 : Validate data to be read for controller recovery commands.(SCGCQ01359018)
- IIC mode string was used to append in case of error. I2C must be used.(SCGCQ01392046)
- Storcli 07.403.00.00 is showing Linkdown for all Phys in c0/pall show command.(SCGCQ01404219)
- Storcli: Instance Validation Failed between "controller-events-schema" and "delete events" JSON output.(SCGCQ01410438)
- Storcli: Instance Validation Failed between " controller-termlog-schema" and "delete termlog" JSON output.(SCGCQ01411534)
- Storcli: Instance Validation Failed between "controller-flushwriteverify-schema.json" and "set flus how riteverify" JSON output.(SCGCQ01412771)
- Strocli: controller-ASO-schema.json is not in JSON format.(SCGCQ01413261)
- Instance Validation Failed between "controller-ASO-schema.json" and "show ASO" json.(SCGCQ01430237)
- Updating pre-ventura SBR fails with "hwdevice" comman.(SCGCQ01438214)
- Adding excludevd option to the help file of patrolread command.(SCGCQ01443435)
- MR 7.2:PPC : StorCLi throws error while loading the saved configuration.(SCGCQ01273381)
- PH4 StorCLI - Segmentation fault observed with show command when fury/cutlass/marlin connected in FreeBSD11.0.(SCGCQ01312757)
- Unified LibMods 7.3 : Fixing resource leaks and missing return statments - Part 2.(SCGCQ01319407)
- Changing of PatrolRead Excludevd property from cli.(SCGCQ01348042)
- CLI is not showing Insight Drives with correct Enclosure/Chassis position.(SCGCQ01373639)
- Removing the memory leaks in dequelog command.(SCGCQ01411544)
- Storcli: Instance Validation Failed between "controller-coercion-schema.json" and "set coercion" JSON output.(SCGCQ01412758)
- Strocli: controller-HDD-SSD-thermalpollinterval-schema.json is not in JSON format.(SCGCQ01412934)
- Non-array delete for objects: destructors will not be called for objects in the array leading to unexpected behaviour.(SCGCQ00804672)
- Reverting back SL_MAX_OS_DRIVE_COUNT value to 300.(SCGCQ01114306)
- Fixing Out of Bounds access and Resource leak.(SCGCQ01304875)
- Inconsistencies between the applications for manage link speed.(SCGCQ01389856)
- Storcli: Instance Validation Failed between "controller-supportssdpatrolread-schema.json" and set supportssdpatrolread json.(SCGCQ01413106)
- Storcli: Instance Validation Failed between "controller-bios-schema.json" and "show bios" JSON output.(SCGCQ01413263)
- Assign VDs suboption in cachecade VD creation is not assigning the intended VDs.(SCGCQ01419754)
- StorCLI: Spindown help syntax is misleading.(SCGCQ01421610)
- Storcli shows two controllers in the system though you have only one cotntroller in the system.(SCGCQ00690355)
- StorCLI Device Interface Information field doesn't reflect inteface of actual device attached to an IT controller.(SCGCQ01352149)
- Perccli Snapshot is Enabled error when deleting VDs.(SCGCQ01378900)
- Correcting yacc rule for bbus show gasguage data command.(SCGCQ01389891)
- Strocli: controller-config-schema.json is not in JSON format.(SCGCQ01412748)
- Strocli: controller-detailed-properties-schema.json is not in JSON format.(SCGCQ01413255)
- DriveID and errormsg are coming improper on drive POH command when failed.(SCGCQ01443683)
- Correcting yacc rule of slaveaddress for command hwdevice.(SCGCQ01389890)
- Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set_personality" JSON output.(SCGCQ01412943)
- Storcli: Instance Validation Failed between "controller-smartpollinterval-schema.json" and "set smartpollinterval" json.(SCGCQ01413018)
- Storcli: Instance Validation Failed between "controller-flushwriteverify-schema.json" and "show flushwriteverify" JSON.(SCGCQ01423452)
- The structure name is changed from oob_i2c to oob to avoid compilation failure in OOB SL.(SCGCQ01015024)
- storclif64 can not create prl11 across 2 enclosure using 32 pds.(SCGCQ01295289)
- StorCLI crashes when VPD file with VPD_Length 0 is tried to update.(SCGCQ01340557)
- Removing the NMR command for setting SCAPVPD.(SCGCQ01389451)
- Storcli: Instance Validation Failed between "controller-perfmode-values-schema.json" and "set perfmode" JSON output.(SCGCQ01412938)
- Instance Validation Failed between "controller-freespace-schema.json" and "show freespace" JSON output.(SCGCQ01414749)

EnhancementRequests:
- MPI2: Add TargetModeAbort by initiator device handle.(SCGCQ00337167)
- New fault code for routine synchronous reset.(SCGCQ01264142)
- MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually.(SCGCQ00574358)
- MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag).(SCGCQ00414050)
- MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply.(SCGCQ00396414)
- MPI2: Add OEM Identifier to BIOS Page 1.(SCGCQ00357228)
- MPI2: Use Slot Information during Port Enable Event Replay option.(SCGCQ00356796)
- MPI2: Add new TargetModeAbort AbortType to only abort Command IUs.(SCGCQ00345215)
- MPI v2.6: Additional request and reply descriptor formats.(SCGCQ00259613)
- API changes for CR55 - PCIe lane/link speed.(SCGCQ01222700)
- API change for Simplified RAID10 Creation.(SCGCQ01222698)
- API Changes Required for Specific OEM Backplane functionality.(SCGCQ01218406)
- API changes for PR SCGCQ01139678 - Method for determining bad ONFI flash in storcli.(SCGCQ01215334)
- MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0.(SCGCQ01213028)
- MPI 2.5: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01208954)
- API changes for PR SCGCQ01127742 - Isolating faulty cable issue from bad drive issue.(SCGCQ01203751)
- MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP.(SCGCQ01180886)
- MR 6.12 - Add JBOD mode personality to MR_CTRL_PERSONALITY.(SCGCQ01146597)
- MR 7.0: Add supportPdMapTargetId flag in MR_CTRL_INFO and MFI_CAPABILITIES.(SCGCQ01141251)
- MR 6.13: Add API support for TFM/SCAP _MR_BBU_VPD_INFO_FIXED parameters.(SCGCQ01139344)
- MR 6.13: Add a new control command to fetch ROC temperature data over I2C.(SCGCQ01137627)
- MR 7.2: Add API support to make application work with Cachecade3.0 on Ventura (Public).(SCGCQ01114969)
- MPI 2.5: Add new connector types.(SCGCQ01085073)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ01002367)
- MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout".(SCGCQ00996127)
- MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1.(SCGCQ00853162)
- MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable.(SCGCQ00791885)
- MPI 2.5: add WWID to BIOS Page 3.(SCGCQ00785208)
- MPI 2.5: update copyright info.(SCGCQ00728066)
- MPI 2.5: BIOS Page 1 additions.(SCGCQ00700829)
- MPI 2.5: distribute Target Command Buffers Received across multiple reply queues.(SCGCQ00685820)
- MPI 2.0: Add product-specific Flag bit to Clean Tool.(SCGCQ00569175)
- Add type BIOS for HashImageType.(SCGCQ00566306)
- Identify physical location of a target device.(SCGCQ00523879)
- MPI 2.5: add reserved fields to IO Unit Page 7 for future use.(SCGCQ00477817)
- MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps".(SCGCQ00471293)
- MPI 2.5: Signed images for FWDownload.(SCGCQ00469990)
- MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL.(SCGCQ00438437)
- MPI 2.5: Toolbox Console Text Display Tool.(SCGCQ00415512)
- Allow Protection Information bit for IR Volume Create.(SCGCQ00385306)
- MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply.(SCGCQ00357551)
- MPI 2.6: add PCIe Device Config Pages.(SCGCQ00345271)
- MPI 2.6: PCIe Switch Config Pages.(SCGCQ00345270)
- MPI 2.6: PCIe Topology Change List Event.(SCGCQ00345266)
- MPI 2.6: add PCIe Event Data (Generic), PCIe Device Status Change Event, and PCIe Enumeration Event.(SCGCQ00345260)
- MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors.(SCGCQ00338506)
- MPI 2.6: PCIe IO Unit Page 0 & 1 definitions.(SCGCQ00336383)
- MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1.(SCGCQ00310439)
- MPI 2.6: update SGL chapter to include PCIe.(SCGCQ00294131)
- MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request.(SCGCQ00294055)
- MPI 2.6: NVMe Encapsulated request.(SCGCQ00264759)
- MPI 2.6: SOP Encapsulated request.(SCGCQ00264755)
-.(SCGCQ01421997)
- Controller should not be reset after firmware download in CLI for SAS 3.5 Controllers.(SCGCQ01399793)
- RPM -verify report error after installing storcli RPM package for linux.(SCGCQ01373354)
- Adding the JBOD personality with EPD passthrough support.(SCGCQ01368469)
- Added the support for EPD-PT creation and operations on a EPD-PT.(SCGCQ01368465)
- List pending profile details of the controller.(SCGCQ01346308)
-.(SCGCQ01291037)
- MPI 2.6 Add Atomic Request Descriptor capability.(SCGCQ00227735)
- MPI 2.6: add IO Unit Control Request.(SCGCQ00345258)
- MPI 2.6: PCIe Link Config Pages.(SCGCQ00345272)
- MPI 2.6: Enclosure Management.(SCGCQ00345273)
- Device Info field for PCIe devices.(SCGCQ00353339)
- MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request.(SCGCQ00360843)
- MPI 2.6: new family values for ProductID fields.(SCGCQ00360952)
- MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11.(SCGCQ00363600)
- Modified address space bits.(SCGCQ00397136)
- MPI 2.6: Add PCIe IO Unit Page 4.(SCGCQ00397563)
- MPI 2.6: Add board power fields to IO Unit Page 7.(SCGCQ00397572)
- MPI 2.6: Add support for SAS Persistent Connections.(SCGCQ00397577)
- MPI 2.6: Add NVMe SGL support.(SCGCQ00398256)
- MPI 2.6: Add NVMe SGL support to IEEE SGL.(SCGCQ00432541)
- MPI 2.6: System Interface Register Set update.(SCGCQ00464402)
- Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request.(SCGCQ00480292)
- MPI 2.6: shutdown operation for IO Unit Control Request.(SCGCQ00496998)
- MPI 2.6: Add supported link rates and widths for PCIe devices.(SCGCQ00564281)
- MPI 2.6: Add additional NVMe AccessStatus codes.(SCGCQ00574070)
- MPI 2.6: Add BootFlags field to Firmware Image Header.(SCGCQ00601869)
- MPI 2.6: Add new FLASH region types.(SCGCQ00619371)
- MPI 2.6: Added an additional signature value for the firmware image header.(SCGCQ00623271)
- MPI 2.6: additional AccessStatus values for PCIe Device Page 0.(SCGCQ00664957)
- MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages.(SCGCQ00680527)
- MPI 2.6: Extend Task Management - Target Reset Method to include PCIe devices.(SCGCQ00686666)
- MPI 2.6: Add device off flag to SCSI Enclosure Processor messages.(SCGCQ00776177)
- MPI 2.6: New Phy event codes added to Ventura.(SCGCQ00789600)
- MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough.(SCGCQ00813389)
- MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura.(SCGCQ00827088)
- MPI 2.6: add PCI Device ID's.(SCGCQ00828497)
- MPI 2.6: methods to report Active Cable power problems.(SCGCQ00831588)
- MPI 2.6: SRIOV support for PCIe devices.(SCGCQ00852827)
- MPI 2.6: Update Flash Signature..(SCGCQ00852831)
- profile management API.(SCGCQ00867953)
- MPI 2.6: add new feature to control NVMe SGL format.(SCGCQ00872169)
- Mega API modifications needed for RMW-FP and Cache bypass features in Ventura.(SCGCQ00875328)
-.(SCGCQ00878757)
- Merging api_overrides mega_api files with the files in the Mega_API development stream.(SCGCQ00883262)
- MPI 2.6: Update Ventura family device ids to match latest EDS.(SCGCQ00915256)
- MPI 2.6: update Marlin-class device IDs.(SCGCQ00915336)
- MPI 2.6: Remove all SOP references.(SCGCQ00925839)
- Ventura: de-feature AHCI.(SCGCQ00941620)
- MPI 2.6: Remove all AHCI references.(SCGCQ00948258)
- MPI 2.6: Add support for SAS-4 and PCIe-4.(SCGCQ00948955)
- MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0.(SCGCQ00949638)
- MPI 2.6: add LinkNum field to the PCIe Link configuration pages.(SCGCQ00954619)
-.(SCGCQ00987840)
- MPI-2.6: backend PCIe feature initialization status reporting.(SCGCQ01009104)
- MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request.(SCGCQ01013930)
- MPI2.6: Fix defines that are not unique within the first 32 characters.(SCGCQ01015826)
- MPI 2.6: direct reporting of negotiated PCIe link width and speed.(SCGCQ01017027)
- MPI 2.6: Backend SRIS mode enable flag.(SCGCQ01018687)
- MPI2.6: Reserve ExtPageTypes for Dragon.(SCGCQ01020473)
- MR_CTRL_INFO expansion from 2K to 4K.(SCGCQ01023741)
- mega api changes for ibuttonless PR.(SCGCQ01059740)
- MPI2.6: Add x16 PCI support for Marlin family products.(SCGCQ01063009)
- MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page.(SCGCQ01071374)
- Profile Management Changes to support requestedProfileID and optimisedProfile.(SCGCQ01075821)
-.(SCGCQ01082303)
-.(SCGCQ01085954)
- MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout".(SCGCQ01092340)
- MEGA_API Changes to incorporate new IO subtype to support redirect cached IO.(SCGCQ01094549)
- MPI 2.6: Add Sea Arch class and Product IDs.(SCGCQ01116837)
- MR 7.0: Add MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT = 7 to mfi.h file.(SCGCQ01133839)
- MPI2.6: Added new image type and flash region definitions.(SCGCQ01136127)
- MPI 2.6: Add new clean tool options.(SCGCQ01141732)
- MPI 2.6: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01146583)
- Define CurrentFwNvmePageSize element in new MFI_REG_STATE_EXT3 register.(SCGCQ01188725)
- MR7.1. Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01213092)
- MPI2.6: Mfg7 support for arbitrary starting slot number.(SCGCQ01213267)
- MPI 2.6: Add new firmware download type (CBB BACKUP).(SCGCQ01258005)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ00988360)
- MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses.(SCGCQ00466819)
- always print StorCLI version information at beginning/top of output.(SCGCQ01396733)
- StorCLI JSON 4.0 compliant schema creation for Contoller level commands.(SCGCQ01365177)
- New command in CLI OEM mode to select either PCIE or I2C as an out of band transport.(SCGCQ01353429)
- Add support to allow Device names greater than 107.(SCGCQ01039328)
- MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs.(SCGCQ00397568)
- MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit.(SCGCQ00884740)
- MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks.(SCGCQ00922213)
- Profile Management: Storcli - Add support for WB bit in profile management show.(SCGCQ01445628)
-.(SCGCQ01428114)
- Add ability to field upgrade CPLD on HBA boards.(SCGCQ01283646)
- Add NVMe device related changes.(SCGCQ01034678)
- Block the MR commands being fired to IT controllers and vice versa from StorCLI.(SCGCQ01315301)
- Unified StorCLI 7.3 : Display serial number information in StorCLI.(SCGCQ01309079)
- Unified StorCLI 7.3 : ARM EFI support to Unified StorCLI.(SCGCQ01292973)
- Unified StorCLI : [Lenovo Purley] Adding tape drive support to Unified StorCLI for IT Ventura controllers.(SCGCQ01351495)

CSETActivities:
- StorCLI firmware download to multiple target devices fails to every other device.(SCGCQ01417390 port of SCGCQ01391339)
- Unified StorCLI 7.3 : Validate data to be read for controller recovery commands.(SCGCQ01399705 port of SCGCQ01359018)
- MR 6.14-CLI: Auto Learn Period Mismatch between CTRL-R and StorCLI..(SCGCQ01396719 port of SCGCQ01391037)
- Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391818 port of SCGCQ00940993)
- The command "Storcli /c0/vall del" its deleting the VDs along with EPDs as well.(SCGCQ01304925 port of SCGCQ00915484)
- Second OCR request not getting triggered, fired when first OCR request about to finish, but O/P shows success.(SCGCQ01300741 port of SCGCQ01290216)
- Cisco - CSCvd49859 - Set VD hidden on a already hidden VD message is not correct from StorCLI.(SCGCQ01298614 port of SCGCQ01295830)
- Mr_6.12_Arm_EFI_CLI:storcli.ef /c0/vall show bbmt dose not display the corrected and uncorrected values.(SCGCQ01293051 port of SCGCQ01059790)
- MR_6.12_Arm_EFI-CLI:storcli.efi /c0/vall set ssdcaching=on/off does not apply for all the Vd's at a time.(SCGCQ01293028 port of SCGCQ01060315)
- MR_6.12_Arm_EFI-Synchronous Exception on running set vpd command with a wrong input file.(SCGCQ01293027 port of SCGCQ01059798)
- Hercules StorCLI: Progress EVents are not logged in StorCLI.(SCGCQ01291546 port of SCGCQ01288785)
- SLT : Requesting user to enter the allocated response length of SMP request page.(SCGCQ01202087 port of SCGCQ01202030)
- Changing ini file name to storelibconfit.ini.(SCGCQ01275669 port of SCGCQ01275496)
- Block OCR after Clearing NVRAM.(SCGCQ01396705 port of SCGCQ01389485)
- ER:SCGCQ00940993-Libmod Changes:Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391828 port of SCGCQ00976651)
- Tape drive connected to MR controller should not take NVMe speeds in to consideration.(SCGCQ01389395 port of SCGCQ01388610)
- Unified LibMod changes for SCGCQ01351495[Tape drive support to StorCLI].(SCGCQ01385205 port of SCGCQ01351565)
- Perccli Snapshot is Enabled error when deleting VDs.(SCGCQ01384442 port of SCGCQ01378900)
- CISCO SQA2 - LR - 1U 10 HDD - StorCLI - /c0/eall/sall start locate throws success message with no LED activity.(SCGCQ01350423 port of SCGCQ01349575 )
- Global Hot Spares shows as TR in storcli DG query when TR is activated on DG.(SCGCQ01332915 port of SCGCQ01047789)
- Correcting error messages for transport errors.(SCGCQ01332859 port of SCGCQ01093152)
- Storcli needs to be fixed for maximum TR info in ctrl show all.(SCGCQ01332851 port of SCGCQ01112673)
- Storclif64 does not return non zero error code on failure.(SCGCQ01320515 port of SCGCQ01318824)
- MR 7.2:PPC : StorCLi throws error while loading the saved configuration.(SCGCQ01318368 port of SCGCQ01273381)
- Need to handle FW return code change for profile management success case.(SCGCQ01318326 port of SCGCQ01307320)
- MR6.12_Arm_storcli.efi:Error Message Wrong on start learn cycle failure scenario.(SCGCQ01293158 port of SCGCQ01039757)
- perccli lists PDs in the wrong order - sometimes.(SCGCQ01292796 port of SCGCQ01290596)
- Storcli shows CV as optimal When Predictive Failure Bit is set.(SCGCQ01392548 port of SCGCQ01392529)
- Storcli shows CV as optimal When Predictive Failure Bit is set.(SCGCQ01392541 port of SCGCQ01392529)
- MR6.12_FW : With spun down PDs and primary path broken, FW does not allow creation of VDs.(SCGCQ01332806 port of SCGCQ01035520)
- Adding a sub option to skip the self-test while reading the POH as per customer request.(SCGCQ01292051 port of SCGCQ01074274)
- MR_6.12_ARM_Storcli.efi:storclio.efi /c0 set pcilinkspeed=3 success and set as 3%.(SCGCQ01293159 port of SCGCQ01058298)
- SLT displays XYRATEX enclosure many fields information as "Unsupported", when we fire a command Get Enclosure Status.(SCGCQ01003523 port of SCGCQ00950453)
- Update Attribution Language - Copyright, Trademark, Confidentiality to Avago.(SCGCQ00793391 port ofSCGCQ00787940)
- StorCLI displays "Next Learn Time" incorrectly.(SCGCQ01345297 port of SCGCQ01344843)
- Factory settings changes for Transport as per new MFC_DEFAULTS in API.(SCGCQ01332916 port of SCGCQ01044891)
- CLI to maintain consistency in the properties/attributes including case between MR and IT.(SCGCQ01309547 port of SCGCQ01308958)
- The command "Storcli /c0/vall del" its deleting the VDs along with EPDs as well.(SCGCQ01305204 port ofSCGCQ00915484 )
- perccli lists PDs in the wrong order - sometimes.(SCGCQ01292797 port of SCGCQ01290596)
- Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391817 port of SCGCQ00940993)
- StorCli should display 128 byte inquiry for drives connected to IT controller including tape.(SCGCQ01388560 port of SCGCQ01388177)
- Factory command is deducting the remanfacturing license even for the first time manufacturing .(SCGCQ01364653 port of SCGCQ01364604)
- Trying to Create Logical disks with UBAD drives gives wrong Failure Message from Storcli.(SCGCQ01358889 port of SCGCQ01356294)
- StorCLI displays "Next Learn Time" incorrectly.(SCGCQ01345296 port of SCGCQ01344843)
- Storcli fails with segmentation fault (core dumped) with foreign import.(SCGCQ01332905 port of SCGCQ01214152)
- C240-M5: Segmentation Fault observed when tried to delete a SWR VD from Version (Max5): 3.1(0.102).( SCGCQ01324969 port of SCGCQ01309488)
- Cisco - CSCvd49859 - Set VD hidden on a already hidden VD message is not correct from StorCLI.(SCGCQ01301733 port of SCGCQ01295830)
- Libmods: Second OCR request not triggered, fired when first OCR request about to finish, but O/P shows success(SCGCQ01290216).(SCGCQ01300727 port of SCGCQ01300721)
- Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01292007 port of SCGCQ00940993)
- ER:SCGCQ00940993-Libmod Changes:Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391827 port of SCGCQ00976651)
- storcli craches with drive show all command for some specific SATA drive.(SCGCQ01386881 port of SCGCQ01385425)
- Unified StorCLI : [Lenovo Purley] Adding tape drive support to Unified StorCLI for IT Ventura controllers.(SCGCQ01383787 port of SCGCQ01351495)
- Transport command is including all when only shared is requested, where it should be failed.(SCGCQ01332907 port of SCGCQ01093145)
- Libmods: SCGCQ01214152 - Storcli fails with segmentation fault (core dumped) with foreign import.(SCGCQ01332872 port of SCGCQ01249484)
- [Lenovo] Storcli may not be able to show the RAID controller in some special situation.(SCGCQ01392462 port of SCGCQ01389914)
- Storcli SegFault -HUU update utility doesn't detect SBMezz if Foreign Config PD exist.(SCGCQ01332850 port of SCGCQ01155309)
- Erase [excludemfg] file=<> command hangs when executed on non-op/jumpered/OCR disabled operational MR Ventura controllers.(SCGCQ01315413 port of SCGCQ01311846)
- PH4 StorCLI -Cutlass-9305-16e FW download failed on Linux/Windows OS platforms.(SCGCQ01311820 port of SCGCQ01311728)
- MR6.12_Arm_Storcli.efi:No error message shown when deleting securitykey fail.(SCGCQ01293161 port of SCGCQ01039756)
- MR6.12_Arm_EFI-CLI:Having multiple Raid volumes created,CLI lists extra entries and all operations on VD’s fails thereafter.(SCGCQ01293053 port of SCGCQ01047493)

0007.0209.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------
Fixes:
 - MegaCli and StorCli can not manage both Liberator (and prior) and TB controllers in the same system under FreeBSD with the mf(SCGCQ00355536)
 - Update VD emulation feature in StorCLI Libmods module to sync with latest APIs.(SCGCQ00357913)
 - StorCLI does not display drive information behind the Blackjack (Alta) interposer correctly(SCGCQ00357948)
 - In paged view the text " Press Enter to continue" should be changed to " Press any key to Continue"(SCGCQ00359629)
 - Code clean up in libmods and sysefi files are added(SCGCQ00359998)
 - Storcli is returning error with show(SCGCQ00360040)
 - StorCLI: Not able to set pr property includessds as onlymixed on Liberator cacheoffload controller(SCGCQ00360814)
 - iMr_Fury_StorCli:4K Drive size shown wrong in Esxi4.1U3(SCGCQ00362216)
 - storcli /c0/d0 show " in that legend missing for "Dgrd/pdgd/Onln/ofLn/Rbld"(SCGCQ00362717)
 - The legend for the PD List table exceeds 80 char limit.(SCGCQ00363455)
 - storcli query for displaying controller properties is showing status , as failure.(SCGCQ00363522)
 - iMR_Inv_6.1:StoreCLI- StoreCLI reports wrong Emulation type for VDs(SCGCQ00364097)
 - StorCLI failed to delete a VD that is just created under Windows 2008(SCGCQ00364248)
 - Reports wrong diskgroup size while querying controller level properties(SCGCQ00364622)
 - UEFI, the O/P of "Current Controller Date/Time" & "Current System Date/time" are not in proper format(SCGCQ00364735)
 - Storcli displays incomplete serial number for some SSDs(SCGCQ00366000)
 - Certain controller features displayed under "show all" exceeds 80-char limit.(SCGCQ00372155)
 - StorCLI crashed when run on a Windows 2008 64-bit with 24GB of RAM and 66 drives attached(SCGCQ00374735)
 - StorCli shows Power Saving Option as enabled, despite IBM Flatwood controller having power saving option completely disabled.(SCGCQ00377364)
 - portings of AdpRestart command(SCGCQ00378135)
 - StorCLI-Legacy:'adpbootdrive get' fails to get bootdrive information.(SCGCQ00378828)
 - Not able to get paged view of StorCLI output on VM-Ware Platform(SCGCQ00379104)
 - Cfgclr command fails without force option in Sparc OS(SCGCQ00396303)
 - storcli crashes on having a non PI drive and trying to create pi vd on all the drive(SCGCQ00413789)
 - EFI_ Storcli: Cannot set vpd file on controller, EFI hangs and cannot proceed for further operations until reboot(SCGCQ00423832)
 - Megacli crashes after invoking any command in SGI system with one 9280-8e and 2 quad port qlogic FC cards.(SCGCQ00438350)
 - Onfi_patch_6.0:Firmware crashed @Line 244 in ../../raid/1078int.c for entering into CTRL-R with Pinned cache in R60 and R6.(SCGCQ00442610)
 - SWR_1.34(SCGCQ00442652)
 - Raptor_Galaxy:State of the Shielded Drive is not displayed using storcli command(SCGCQ00467502)
 - Raptor_Galaxy_Tencent:Tencent Storcli detecting the H710 PERC card.(SCGCQ00475583)
 - Storcli internal errors should return with 1001, but its coming as -1(SCGCQ00479843)
 - Try to create a Exclusive VD, but after creation it still shows as Shared VD.(SCGCQ00484560)
 - MR6.2 : Storcli shows incorrect "Bus" information when "/c0 show all" is run(SCGCQ00518201)
 - Unable to make R10 through Ctrl R using 4k drives(SCGCQ00518579)
 - PPC64 :: MR Liberator :: Storcli Version 1.09.01 is showing wrong Creation Date and Time in VD properties(SCGCQ00569935)
 - MR_Inv_6.3_PPC:Storcli- Retreiving LDBBM info through storcli is failing on SLES11 SP2 PPC64(SCGCQ00574835)
 - "/cx/ex show phyerrorcounters" gives core dump on freeBSD 32 and 64 bit.(SCGCQ00644123)
 - Storcli : unable to set patrol read delay(SCGCQ00645195)
 - MR6.4_StorCLI_240VD: StorCLI crashes on issuing /c1 set cc=conc delay=10 starttime=2014/12/12 12 excludevd=0(SCGCQ00649324)
 - Storlib header file checkin and make compatible changes in CLI code.(SCGCQ00653742)
 - StorCLIO_1.09.09 : Not able to set subOEMid in Rhel 5.10 x64 bit.(SCGCQ00674131)
 - While creating cachecade vd with one SAS-SSD;Raid 1 option is also enabled(SCGCQ00712171)
 - H330: Firmware Crash is hit while creating the Raid1 vd without drives selected(SCGCQ00725192)
 - After Rebuilding, DHS and Expand VD operations failed to update as per VD properties(SCGCQ00730505)
 - 6.6_StorCli: StorCli lists all cascaded enclosures at position 0.(SCGCQ00756647)
 - FW breaks in iMR when excluding VD's from CC(SCGCQ00758770)
 - SupportMaxRate SATA is not listed in PD allowed operations.(SCGCQ00759178)
 - SED adapterOperation detailed is not shown in detailed show controller properties(SCGCQ00759183)
 - Adapters are not listed in sorted order.(SCGCQ00759969)
 - MR6.6: Segmentation fault (Core Dumped) in CLI when setting any invalid value for PR start time(SCGCQ00760398)
 - /c0 show all does not list hwCfg information as compared to MegaCLI.(SCGCQ00760752)
 - Storclio : Different error code is coming for 'set pcilinkspeed' in VMware 4.1U3(SCGCQ00762663)
 - StorCLI is not updated with the error Message for all new MFI_STAT added in mfistat.h(SCGCQ00765712)
 - StorCLI VMware Binary not displaying detailed description for phyerrorcounters of enclosures(SCGCQ00765762)
 - StorCLI shows CacheBypass Size and CacheBypass Mode feature enabled against a VD which is associated with a CacheCade VD(SCGCQ00772243)
 - Active operation(s) is coming as none when virtual drive erase is in progress.(SCGCQ00779789)
 - MR6.6:StorCLI shows incorrect information about "Cache Vault Flash Size"(SCGCQ00782882)
 - "cpybck" help is not coming in Legends(SCGCQ00784808)
 - VD level hide/unhide is not possible through storcli in PPC(SCGCQ00785400)
 - MFCdefaults : DisableHII option needs to be include in getShowDefaults()(SCGCQ00792232)
 - Comparing an array to null is not useful: "rawSmartData != NULL"(SCGCQ00793374)
 - MR_6.7_STROCLI: Command "./storcli64 /c0/ex/sx reset phyerrorcounters" fails in RHEL6.6 PPC64(SCGCQ00794394)
 - .(SCGCQ00800878)
 - Deallocation of the same memory more than once(SCGCQ00802031)
 - Memory leak happening in failure case since not freeing before returning error code.(SCGCQ00804588)
 - Out-of-bounds access and array delete misuse(SCGCQ00804680)
 - MR_6.7_ Storcli: "Storcli /cx/eall/sall show " gives no enclosure found if two enclosures are connected in multipath scenario(SCGCQ00805547)
 - Not able add new VD in Drive Group(SCGCQ00813314)
 - MR_6.7: Storcli Command "./storcli /c0/v2 set accesspolicy=RmvBlkd " fails for a blocked source VD.(SCGCQ00814939)
 - Storcli cannot create R10 in iMR with 6 or 8 drives per span.(SCGCQ00827049)
 - Storcli crashes instead of showing error message on enabling caching on Source VDs and C(SCGCQ00827299)
 - storcli /call show all fails with "command invalid"(SCGCQ00830269)
 - New PD_Degraded media events are not logging correctly in PPC(SCGCQ00837342)
 - Profile Mgmt API Changes(SCGCQ00883008)
 - MR_RAID_CTX_G35 has one too many bits(SCGCQ00886417)
 - Reintroduce numSGEExt Field in Raid Context for Invader to support 1MB IO(SCGCQ00927738)
 - The code had events with repetitive ID and some structures clashing(SCGCQ00948535)
 - Controller detection fails in EFI environment with MR Ventura card(SCGCQ01001372)
 - CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23(SCGCQ01001936)
 - CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23 has been added back again(SCGCQ01014835)
 - 800C error when execting Get MFC default function(SCGCQ01037840)
 - ThinkServer: Cyborg [Purley] Sotrcli (007.0022.0000.0000) cannot show the correct PCI bus/dev/func number for Invader and Ven(SCGCQ01087936)
 - Serial Number for drives were having spaces when displaying in Storcli(SCGCQ01126284)
 - No ISE Capable field(SCGCQ01148693)
 - MR7.1_NVMe:Segmentation fault seen on storcli while generating controller info with preserved cache(SCGCQ01193175)
 - Ventura-Beta: Storcli/Storclif utilities hit Segmentation fault when foreign configuration is present(SCGCQ01198698)
 - Fixing Resource leaks(SCGCQ01205356)
 - resource validation before de referencing(SCGCQ01206104)
 - Fixing resource leaks in libmods(SCGCQ01208044)
 - Fixing resource leak and pointer to local variable coverity defect in libmods(SCGCQ01209393)
 - Fixing Logically dead code and Wrong size arguments in CLI(SCGCQ01209414)
 - Unified Libmods StorCLI 7.1:Fixing resource leaks-Part 4(SCGCQ01209473)
 - Fix for resource leak in system config show(SCGCQ01210133)
 - MR7.1_NVMe: comma missing between RAID10 and RAID60 in the RAID Level Support at /c0 show all output(SCGCQ01214415)
 - Storcli does not show "NVME" in supported Drives.(SCGCQ01215383)
 - some of the drive properties is not shown properly on querying the drive info through storcli(SCGCQ01229923)
 - Unified StorCLI 7.1:Incorrect usage of STORCLIO and STORCLIF macros(SCGCQ01234217)
 - NVMe PD SMART DATA shows all 0's(SCGCQ01236052)
 - StorCLIO states wrong OS version for Windows 2016(SCGCQ01274715)
 - Individual Phy information on an IT works, when given with multiple Phys it says "Unsupported Command".(SCGCQ01275381)
 - When invalid enclsoure is specified as user input , the output is not correct(SCGCQ01275687)
 - IT show all command displays Physical Drive Information headline wihtout table when no drive is connected(SCGCQ01276688)
 - Unified StorCLI 7.2:Windows only:Drive properties headline gets truncated during drive show all command(SCGCQ01280928)
 - StorCLI: Not able to detect Liberator Controller on FreeBSD 9.0(64-bit)(SCGCQ00362421)
 - PCI Info for FreeBSD needs to be indicated as "N/A"(SCGCQ00365632)
 - Vmware CLI fails to set the phy linkspeed(SCGCQ00371445)
 - System halts on issuing storcli commands in EFI Environment.(SCGCQ00374336)
 - PERC9:Storcli ld info command displays R10 vd Span Depth to 1.(SCGCQ00374979)
 - StorCli_MR: While Creating RAID1 with four drives command facing the "C0:BAIL_OUT at line 1354" on Flatwood Board(SCGCQ00394883)
 - core dump while issuing storcli command ./storcli /c0/fall show all.(SCGCQ00448094)
 - Some Numeric values in CLI o/p comes in Hex format(SCGCQ00481474)
 - Unable to insert a drive after setting a drive as 'Missing' .(SCGCQ00490620)
 - Some sparc structures missing for storcli.(SCGCQ00504585)
 - MR Liberator : PPC SERVERGY Server : MonTask: line 541 in file ../../raid/raidpci.c(SCGCQ00567761)
 - PPC64 :: MR Liberator :: All commands of StorCli is failing with segmentation fault after creating a GlobalHotSpare(SCGCQ00579658)
 - storecli reports wrong size on 3000MB VD(SCGCQ00644545)
 - Cannot create a VD smaller than 800MB with 4K drives(SCGCQ00649962)
 - MR6.4: Storcli show command does not display all the controllers plugged into the server(SCGCQ00653672)
 - Add support bits for uneven-span and SSHA support(SCGCQ00755063)
 - MR_6.6_Storcli: Storcli reports supercap state 'unknown' while learn is happening on the controller.(SCGCQ00758101)
 - Exception with command /co show badblocks or "storcli /cx flasherase"(SCGCQ00758924)
 - SSM-FLASh drives property is displayed for regular drives.(SCGCQ00759290)
 - Support details are not shown in /c0 show all for discard cache (stalling LD deletion)(SCGCQ00759959)
 - MR_6.6: StorCLI showing incorrect value for next Schedule time for consistency check after disabling the CC(SCGCQ00760385)
 - MR 6.6 Prealpha2 Storcli:Similar PCI address(BDF number) is displayed for multiple controllers connected to FreeBSD 9.3.(SCGCQ00761937)
 - StorCLI /c0 show all command does not reflect the discard vd delete filed(SCGCQ00764658)
 - StorCLI shows CacheBypass Size and CacheBypass Mode feature enabled against a CacheCade VD(SCGCQ00765714)
 - StorCLI shows wrong "Number of blocks" for a 65.5TB VD size(SCGCQ00765759)
 - Patrol read delay is showing wrong value when set to continuous(SCGCQ00767347)
 - Showing wrong creation date for Autoconfigured virtual drives(SCGCQ00767363)
 - Storcli errors are printing in a different line.(SCGCQ00771626)
 - Storcli has option to set PR maxconcurrentpd but show is not present(SCGCQ00772302)
 - vpdpage should be read from 4 bytes to get serial number of drive(SCGCQ00772332)
 - GB scale to be added while showing CacheCade size in CLI(SCGCQ00778577)
 - MR6.6_CLI_FreeBSD: Displaying incorrect Driver name(SCGCQ00779800)
 - CTRL-R:2 iMR Card in same System hitting Montask(SCGCQ00783357)
 - Readability : Output string need to be updated for supportForceTo512e in show all command(SCGCQ00792202)
 - The HDD firmware revision is shown blank for few drives connected.(SCGCQ00793761)
 - MR_6.7_STROCLI: "./storcli64 /c0/ex show phyerrorcounters" gives segmentation fault in RHEL6.6 PPC64(SCGCQ00794393)
 - Explicit null dereferenced in rmdatamf.cpp causing wrong result.(SCGCQ00795335)
 - Resource leak(SCGCQ00804745)
 - .(SCGCQ00811452)
 - Unified StorCLI:EFI:Duplicate instances of Controller gets added to the ControllerIdList pointer(SCGCQ00936672)
 - Unified StorCLI 7.1:Coverity fixes(SCGCQ01206205)
 - Fix for profile management support check bit(SCGCQ01208103)
 - Unified StorCLI 7.1:Fxing resource leaks-Part 3(SCGCQ01209411)
 - Unified Storcli: Fixing resource leak issues(SCGCQ01209413)
 - SAS3.5 Ventura(SCGCQ01219196)
 - Discrepancy while installing and uninstalling of latest Storcli Package(SCGCQ01234153)
 - StoreCLI unified for Ventura version cannot display direct attached disk serial number information.(SCGCQ01280169)
 - pall compare shows the current linkspeed on MR controllers(SCGCQ01282376)
 - Need to handle FW return code change for profile management success case(SCGCQ01307320)
 - MegaCLI adpgetpciinfo returns a static Bus Number value "17d0"(SCGCQ00357263)
 - iMR_Inv_6.1:StorCLI- StorCLI does not show 'Unsupported/Blocked' state for 4K drives even though FW is not supporting 4K(SCGCQ00384644)
 - StorCli_MR: While creating VD using default values FW allows read policy as"Ra=Read Ahead Adaptive" as against PR-317400(SCGCQ00397663)
 - MR6.1: Hamlin: Is VD Emulated=Yes when emulationType=1(SCGCQ00424978)
 - storcli /c0 show is not listinf SWR controller(SCGCQ00454971)
 - Pcli: Pcli crashes while try to set securitykey for controller.(SCGCQ00471116)
 - Raptor Galaxy : Storcli(SCGCQ00475562)
 - Command "./Storcli /call/eall/sx set offline" fails with ERRcode1001 and ERRmsg drive not found.(SCGCQ00503981)
 - Wrong size of CacheCade VD is getting displayed after making one PD offline(SCGCQ00505771)
 - Some characters missing while querying for VD properties with having 64 VD's on a controller.(SCGCQ00529763)
 - Storclio_1.09.00:Fails to set SubOEMID on Solaris OS .(SCGCQ00568073)
 - MR_Inv_6.3_PPC:Storcli-WWN is showing blank for SAS PDs on SLES11 SP2 PPC64(SCGCQ00572800)
 - PPC64 :: MR Liberator :: ./storcli64 /c0 show dequeuelog file command failing with segmentation fault(SCGCQ00581416)
 - MR : on querying PR status, storcli hits segmentation fault.(SCGCQ00601775)
 - /c0 set cc=conc command fails with iMR card.(SCGCQ00603174)
 - storelib header file changes porting(SCGCQ00609942)
 - MR_6.4_StorCli_EFI: Storcli.efi crashes for iMR card.(SCGCQ00674023)
 - Storcli doesn't show SN of Samsung SSD 200/400/800 in SWRAID version 1.32(SCGCQ00674969)
 - storcli /c0 show all is not displaying "support vd hide" and "support HOQrebuild" feilds and legends are not displayed for HD(SCGCQ00695070)
 - In Windows and Linux only controller grouping is working but not sorting(SCGCQ00752000)
 - Boot Volume details is shown in Megacli but not with storcli.(SCGCQ00759187)
 - ASO count mismatch in show ASO w.r.t ASO in storcli show all cmd(SCGCQ00779806)
 - Reviewing the Code AdataMfi, RmDataMf and VdDataMf files.(SCGCQ00785918)
 - Missing the Display of the property temperatureCtrl.(SCGCQ00792264)
 - When Supercap SOH is reported bad, CLI still see the Supercap status as "Optimal"(SCGCQ00794760)
 - Explicit null dereferenced in vddatamf.cpp (getVdDetldInfo)(SCGCQ00795336)
 - fisResBuffer memory allocation is not considering the failure case(SCGCQ00796206)
 - Memory not freed which can cause leak(SCGCQ00804554)
 - Varailble need to be freed before returning in all failure case(SCGCQ00804650)
 - IDA show incorrect RAID controller type information(SCGCQ00806966)
 - MR_6.8_Storcli: Cachevault flash size shows differently for different commands in storcli under RHEL6.6 PPC64(SCGCQ00837197)
 - Read policy should be 'NORA' for IMR controller instead of 'none'(SCGCQ00840372)
 - ASO no mismatch between the commands 'storclif show' and 'storclif /c0 show aso'(SCGCQ01081111)
 - MR7.1_NVMe: Post NVMe VD Creation, SAS VD Creation of any Raid Level (Except R0) is not allowed(SCGCQ01127464)
 - Ventura: OEMID is shown as LSI in scheduled tasks on querying controller info.(SCGCQ01157723)
 - Removing Unused and logically dead code in storcli(SCGCQ01204045)
 - Remove all the manufacturing/Factory commands from end customer CLI tool(SCGCQ01206492)
 - Unified StorCLI 7.1-Fixing resource leaks in IT controller framework and command processors-Part2(SCGCQ01207685)
 - NVMe 7.1:Failure description string is empty in storcli(SCGCQ01234083)
 - Second OCR request not getting triggered, fired when first OCR request about to finish, but O/P shows success.(SCGCQ01290216)
 - iMR_Inv_6.1:StoreCLI-StoreCLI does not give proper message while trying to create 33rd VD on iMR FURY controller(SCGCQ00364332)
 - MR: not able to create PRL11 using 96 drives.(SCGCQ00381100)
 - StorCLI-Invader : The "coercion" mode is not in sync with the legacy values.(SCGCQ00383043)
 - Raptor Galaxy:No of blocks displayed for a VD remains same for all VD sizes.(SCGCQ00465956)
 - StorCLI reports controller status as 'OK' when Arctrus controller(9361-8i) booted in safe mode(SCGCQ00523370)
 - MR_Inv_6.3_PPC:Storcli- Storcli gives 'Segmentation fault' while retriving 'advanced software options' on SLES11 SP2 PPC64(SCGCQ00574287)
 - MR6.4_StorCLI: c0 show controller health is failing(SCGCQ00627672)
 - Add adapterOperation support details in /c0 show all for Emulationtype.(SCGCQ00759181)
 - OEMID is coming as "Unknown" for /c0 show all(SCGCQ00759862)
 - CPLD(SCGCQ00787705)
 - CPLD UPDATE : cpld upgradableCPLD support bit need to add under hardware configuration(SCGCQ00792233)
 - rlListPtr is not handled properly in failure case(SCGCQ00796227)
 - Segmentation fault while querying for GHSP/DHSP while drive is going in shield-HSP state.(SCGCQ00820392)
 - LDViewMirror is giving segmentation fault(SCGCQ00830435)
 - Storcli shows caching is enabled on Source VD when CCVD is in offline state(SCGCQ00835758)
 - Storcli gives wrong error code with respect to FW state while converting JBOD to UG(SCGCQ00839321)
 - Checking in compilation error for Libmods(SCGCQ00919973)
 - VD Creation fails with "Invalid Arguments" error with latest FW Headers(SCGCQ01001356)
 - Coverity Fixes for Unified Storcli 7.1 stream(SCGCQ01204055)
 - PH2: Pre Alpha-Ventura B0 storcli command not exited when storcli /c1 show issued.(SCGCQ01205407)
 - Fixing resource leaks and logically dead code in cli.(SCGCQ01208101)
 - Ventura B0 PH3 StorCLI : Segmentation fault seen with show command on freebsd 10.2 X86 OS(SCGCQ01250553)
 - MR 7.2:PPC : StorCLi throws error while loading the saved configuration.(SCGCQ01273381)
 - Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01274709)
 - StorCLI does not provide command to set HSM or HCOE SCGCQ00358662(SCGCQ00360745)
 - StorCLI cannot displays information for controller in Safe mode(SCGCQ00365950)
 - StorCLI does not show both "Current Write Policy" and "Default Write Policy" for VD(SCGCQ00408070)
 - debug prints are present when issuing /co/eall show(SCGCQ00475815)
 - PCLI Sparc(1.07.02):" Cli show all" command fails with error msg "Error! App exec failed in FW PCLIError! Internal".(SCGCQ00518543)
 - Verify StorCLI warns on destructive operations(SCGCQ00712982)
 - /c0 show all page are having some incorrectness in controller information(SCGCQ00716584)
 - MR6.5alpha:Segmentation fault(coredump) observed on executing ./storcli /c1/v63 show all for 64th cachecade VD in ubuntu14.04(SCGCQ00729691)
 - Add adapterOperation support details in /c0 show all for cachebypassMode.(SCGCQ00757358)
 - supportCPLDUpdate support bit needs to be updated in contoller detailed information(SCGCQ00792200)
 - supportDrvActivityLEDSetting supported bit need to be update in Supported adapater Operations(SCGCQ00792211)
 - Incorrect sizeof expression in dcmdprm(SCGCQ00793354)
 - Non-array delete for objects in rmdatamf(SCGCQ00793361)
 - Storcli displays wrong native driver version on ESXi5.5 when quered .(SCGCQ00803420)
 - Variable going out of scope without freeing which causes memory leak(SCGCQ00804663)
 - Non-array delete for objects: destructors will not be called for objects in the array leading to unexpected behaviour.(SCGCQ00804672)
 - FW hangs during SVD and CCVD migration based on DDR Size(SCGCQ00809736)
 - Unified CLI:EFI:Ventura IT:Adpcount is zero when the controller is in fault state(SCGCQ01016583)
 - Ventura:CLI App stopped working on executing /c0/eall/sall delete hotsparedrive(SCGCQ01081096)
 - Reverting back SL_MAX_OS_DRIVE_COUNT value to 300(SCGCQ01114306)
 - PD related information missing for NVMe drives(SCGCQ01126564)
 - Factory settings command needs to validate the manufacturing data in the INI, and log the license details with proper time(SCGCQ01205365)
 - Unified StorCLI 7.1:IT Firmware downgrade should be supported in StorCLIO and not StorCLI(SCGCQ01232854)
 - StorCLI(SCGCQ01274554)
 - Adapter 0: Failed to start SecureErase on Virtual Drive 0 in VMware_ESXi_5.1(SCGCQ00348911)
 - iMr_Fury_StorCLi:SectorSize show as "512KB" for 512Bytes drives(SCGCQ00362070)
 - StorcLi_5.7: Remove the description for "Ra=Read Ahead Adaptive" in VD show info.(SCGCQ00396665)
 - The bootwithpinnedcache logic is backwards, both storcli and the FW are affected(SCGCQ00436107)
 - StorCli: Segmantation fault appearing in storcli when issuing /c0/fall show(SCGCQ00564008)
 - CS2.0: Ctrl-R Domain Id is not showing in controller properties(SCGCQ00622605)
 - Storcli shows two controllers in the system though you have only one cotntroller in the system.(SCGCQ00690355)
 - Remove the code related to enableVCor feild this was used for ASD and now it is not used any more.(SCGCQ00789402)
 - supportForceFlash needs to add under suported adapter operations(SCGCQ00792205)
 - Operands don't affect result in pddatamf.cpp causing wrong result(SCGCQ00795334)
 - Unchecked return value in rmdatamf.cpp (getControllerStatus)(SCGCQ00795342)
 - MR_6.7_Storcli: Storcli reports wrong tmm and scap date of manufacture under scap properties in RHEL6.6 PPC64(SCGCQ00801311)
 - LibMod changes for CTLR+R (PERC9.2) to read Disk Write Cache settings of PD.(SCGCQ00811117)
 - StorCLI 7.0015 cannot create VD using firmware 6166 under Windows 2012(SCGCQ01046368)
 - Ventura:StorCLI-EFI-StorCLI hang on Purley @ Intel/Quanta for 3408(SCGCQ01052844)
 - SAS3 Invader/Intruder-Storcli : IR card is getting detected in EFI shell(SCGCQ01081353)
 - No details of pending FW images when run StorCLI /c0 show all after update to new firmware(SCGCQ01090082)
 - Libmod changes for defect(SCGCQ01112455) storcli says failed to exit from storelib IT library while enquiring the controller info(SCGCQ01114437)
 - PH2: Pre Alpha-Ventura B0 download completeflash command fails.(SCGCQ01198721)
 - Update /sall show legend to show powersave for SSDs in addition to spun down for HDDs(SCGCQ01213236)
 - MR7.1 StorCLI misspelling of "Drive Acitivy LED" During Set(SCGCQ01229289)
 - Help for Compare linkspeed is not complete(SCGCQ01275454)
 - CLI reporting Large VD (56TB) size slightly smaller than other apps (by .001)(SCGCQ00477037)
 - Storcli /c0 show ASO fails and delay in displaying .(SCGCQ00493491)
 - Storcli reports VD Type as "Rec1" during reconstruction on SPARC.(SCGCQ00499067)
 - Command /cx/ex show phyerrorcounters gives bus error in Orcale Enterprise Linux(SCGCQ00799426)
 - Libmod changes to support profile management(SCGCQ01048228)
 - storcliF 7.23.0.0: VD shown on wrong controller in a system with 2 Talladega 16i controllers installed(SCGCQ01080627)
 - Merge of enclosure related changes for phyerror counters from 6.x(SCGCQ01123876)
 - Ventura PH3(SCGCQ01253012)
 - Compare linkspeed says unsupported when given with multiple Phys(SCGCQ01275455)
 - coverity removing out of bounds reads from code(SCGCQ01280460)
 - CSET: storelib header file checkin for the latest changes done by storelib(SCGCQ00521999)
 - StorCLI :supportDisableImmediateIO adapter properties need to be added under show all command(SCGCQ00792085)
 - Firmware error code status MFI_STAT_SECURE_SYSTEM_PD_EXISTS needs to be update in code(SCGCQ00792234)
 - Resource leak in VdDataMf scanPartitions(SCGCQ00793363)
 - Storcli can't create AHCI LDs(SCGCQ00897637)
 - Unified StorCLI:EFI:Masking the SL_GET_CTRL_INFO command when the adapter is in invalid/bad state.(SCGCQ00936676)
 - The structure name is changed from oob_i2c to oob to avoid compilation failure in OOB SL(SCGCQ01015024)
 - NVMe PD firmware flash failing (not working) as per controller logs, StorCLI show success message(SCGCQ01218214)
 - Detailed help missing for IT erase commands(SCGCQ01275474)
 - start and stop locate from storcli on IT card with multiple drive option is not working.(SCGCQ01275671)
 - Coverity: Adding checks for unchecked return values of function calls(SCGCQ01280453)
 
Enhancement
 
 - MPI2: Add TargetModeAbort by initiator device handle(SCGCQ00337167)
 - New fault code for routine synchronous reset(SCGCQ01264142)
 - MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually(SCGCQ00574358)
 - MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag)(SCGCQ00414050)
 - MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply(SCGCQ00396414)
 - MPI2: Add OEM Identifier to BIOS Page 1(SCGCQ00357228)
 - MPI2: Use Slot Information during Port Enable Event Replay option(SCGCQ00356796)
 - MPI2: Add new TargetModeAbort AbortType to only abort Command IUs(SCGCQ00345215)
 - MPI v2.6: Additional request and reply descriptor formats(SCGCQ00259613)
 - API changes for CR55(SCGCQ01222700)
 - API change for Simplified RAID10 Creation(SCGCQ01222698)
 - API Changes Required for Specific OEM Backplane functionality(SCGCQ01218406)
 - API changes for PR SCGCQ01139678(SCGCQ01215334)
 - MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0(SCGCQ01213028)
 - MPI 2.5: Add two new reason codes to Active Cable Exception Event Data(SCGCQ01208954)
 - API changes for PR SCGCQ01127742(SCGCQ01203751)
 - MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP(SCGCQ01180886)
 - MR 6.12(SCGCQ01146597)
 - MR 7.0: Add supportPdMapTargetId flag in MR_CTRL_INFO and MFI_CAPABILITIES(SCGCQ01141251)
 - MR 6.13: Add API support for TFM/SCAP _MR_BBU_VPD_INFO_FIXED parameters(SCGCQ01139344)
 - MR 6.13: Add a new control command to fetch ROC temperature data over I2C(SCGCQ01137627)
 - MR 7.2: Add API support to make application work with Cachecade3.0 on Ventura (Public)(SCGCQ01114969)
 - MPI 2.5: Add new connector types(SCGCQ01085073)
 - MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout"(SCGCQ00996127)
 - MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply(SCGCQ00988360)
 - MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1(SCGCQ00853162)
 - MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable(SCGCQ00791885)
 - MPI 2.5: add WWID to BIOS Page 3(SCGCQ00785208)
 - MPI 2.5: update copyright info(SCGCQ00728066)
 - MPI 2.5: BIOS Page 1 additions(SCGCQ00700829)
 - MPI 2.5: distribute Target Command Buffers Received across multiple reply queues(SCGCQ00685820)
 - MPI 2.0: Add product-specific Flag bit to Clean Tool(SCGCQ00569175)
 - Add type BIOS for HashImageType.(SCGCQ00566306)
 - Identify physical location of a target device(SCGCQ00523879)
 - MPI 2.5: add reserved fields to IO Unit Page 7 for future use(SCGCQ00477817)
 - MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps"(SCGCQ00471293)
 - MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses(SCGCQ00466819)
 - MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL(SCGCQ00438437)
 - Allow Protection Information bit for IR Volume Create(SCGCQ00385306)
 - MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply(SCGCQ00357551)
 - MPI 2.6: add PCIe Device Config Pages(SCGCQ00345271)
 - MPI 2.6: PCIe Switch Config Pages(SCGCQ00345270)
 - MPI 2.6: PCIe Topology Change List Event(SCGCQ00345266)
 - MPI 2.6: add PCIe Event Data (Generic), PCIe Device Status Change Event, and PCIe Enumeration Event(SCGCQ00345260)
 - MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors(SCGCQ00338506)
 - MPI 2.6: PCIe IO Unit Page 0 & 1 definitions(SCGCQ00336383)
 - MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1(SCGCQ00310439)
 - MPI 2.6: update SGL chapter to include PCIe(SCGCQ00294131)
 - MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request(SCGCQ00294055)
 - MPI 2.6: NVMe Encapsulated request(SCGCQ00264759)
 - MPI 2.6: SOP Encapsulated request(SCGCQ00264755)
 - Added the new Component version for SBR in both Controller-info case and also in Pending FW images use case.(SCGCQ01093183)
 - Libmods changes for EFI support for Unified storcli(SCGCQ00923719)
 - Add set "Fail PD on SMARTer" property feature to StorCLI(SCGCQ00818101)
 - OEL Support for SPARC(SCGCQ00787923)
 - Added the library functions for the new MR API bits and LD operations.(SCGCQ00685010)
 - Added the library functions for the new MR API bits and LD operations.(SCGCQ00685007)
 - Display the NCQ enabled/disabled status of every SATA disk drive in the output of StorCLI and MegaCLI(SCGCQ00564477)
 - CSET: (Tbolt PR 211180) Punctured Block Logging Improvements(SCGCQ00342399)
 - MPI 2.6 Add Atomic Request Descriptor capability(SCGCQ00227735)
 - MPI 2.6: add IO Unit Control Request(SCGCQ00345258)
 - MPI 2.6: PCIe Link Config Pages(SCGCQ00345272)
 - MPI 2.6: Enclosure Management(SCGCQ00345273)
 - Device Info field for PCIe devices(SCGCQ00353339)
 - MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request(SCGCQ00360843)
 - MPI 2.6: new family values for ProductID fields(SCGCQ00360952)
 - MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11(SCGCQ00363600)
 - Modified address space bits(SCGCQ00397136)
 - MPI 2.6: Add PCIe IO Unit Page 4(SCGCQ00397563)
 - MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs(SCGCQ00397568)
 - MPI 2.6: Add board power fields to IO Unit Page 7(SCGCQ00397572)
 - MPI 2.6: Add support for SAS Persistent Connections(SCGCQ00397577)
 - MPI 2.6: Add NVMe SGL support(SCGCQ00398256)
 - MPI 2.6: Add NVMe SGL support to IEEE SGL(SCGCQ00432541)
 - MPI 2.6: System Interface Register Set update(SCGCQ00464402)
 - Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request(SCGCQ00480292)
 - MPI 2.6: shutdown operation for IO Unit Control Request(SCGCQ00496998)
 - MPI 2.6: Add supported link rates and widths for PCIe devices(SCGCQ00564281)
 - MPI 2.6: Add additional NVMe AccessStatus codes(SCGCQ00574070)
 - MPI 2.6: Add BootFlags field to Firmware Image Header(SCGCQ00601869)
 - MPI 2.6: Add new FLASH region types(SCGCQ00619371)
 - MPI 2.6: Added an additional signature value for the firmware image header(SCGCQ00623271)
 - MPI 2.6: additional AccessStatus values for PCIe Device Page 0(SCGCQ00664957)
 - MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages(SCGCQ00680527)
 - MPI 2.6: Extend Task Management(SCGCQ00686666)
 - MPI 2.6: Add device off flag to SCSI Enclosure Processor messages(SCGCQ00776177)
 - MPI 2.6: New Phy event codes added to Ventura(SCGCQ00789600)
 - MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough(SCGCQ00813389)
 - MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura(SCGCQ00827088)
 - MPI 2.6: add PCI Device ID's(SCGCQ00828497)
 - MPI 2.6: methods to report Active Cable power problems(SCGCQ00831588)
 - MPI 2.6: SRIOV support for PCIe devices(SCGCQ00852827)
 - MPI 2.6: Update Flash Signature.(SCGCQ00852831)
 - profile management API(SCGCQ00867953)
 - MPI 2.6: add new feature to control NVMe SGL format(SCGCQ00872169)
 - Mega API modifications needed for RMW-FP and Cache bypass features in Ventura(SCGCQ00875328)
 - Merging api_overrides mega_api files with the files in the Mega_API development stream(SCGCQ00883262)
 - MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit(SCGCQ00884740)
 - MPI 2.6: Update Ventura family device ids to match latest EDS(SCGCQ00915256)
 - MPI 2.6: update Marlin-class device IDs(SCGCQ00915336)
 - MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks(SCGCQ00922213)
 - MPI 2.6: Remove all SOP references(SCGCQ00925839)
 - Change library name to SLIT(SCGCQ00933175)
 - Ventura: de-feature AHCI(SCGCQ00941620)
 - MPI 2.6: Remove all AHCI references(SCGCQ00948258)
 - MPI 2.6: Add support for SAS-4 and PCIe-4(SCGCQ00948955)
 - MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0(SCGCQ00949638)
 - MPI 2.6: add LinkNum field to the PCIe Link configuration pages(SCGCQ00954619)
 - MPI-2.6: backend PCIe feature initialization status reporting(SCGCQ01009104)
 - MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request(SCGCQ01013930)
 - MPI2.6: Fix defines that are not unique within the first 32 characters(SCGCQ01015826)
 - MPI 2.6: direct reporting of negotiated PCIe link width and speed(SCGCQ01017027)
 - MPI 2.6: Backend SRIS mode enable flag(SCGCQ01018687)
 - MPI2.6: Reserve ExtPageTypes for Dragon(SCGCQ01020473)
 - MR_CTRL_INFO expansion from 2K to 4K(SCGCQ01023741)
 - mega api changes for ibuttonless PR(SCGCQ01059740)
 - MPI2.6: Add x16 PCI support for Marlin family products(SCGCQ01063009)
 - MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page(SCGCQ01071374)
 - Profile Management Changes to support requestedProfileID and optimisedProfile(SCGCQ01075821)
 - MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout"(SCGCQ01092340)
 - MEGA_API Changes to incorporate new IO subtype to support redirect cached IO(SCGCQ01094549)
 - MPI 2.6: Add Sea Arch class and Product IDs(SCGCQ01116837)
 - MR 7.0: Add MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT = 7 to mfi.h file(SCGCQ01133839)
 - MPI2.6: Added new image type and flash region definitions(SCGCQ01136127)
 - MPI 2.6: Add new clean tool options(SCGCQ01141732)
 - MPI 2.6: Add two new reason codes to Active Cable Exception Event Data(SCGCQ01146583)
 - Define CurrentFwNvmePageSize element in new MFI_REG_STATE_EXT3 register(SCGCQ01188725)
 - MR7.1. Add MR API bit to indicate the profile is NVMe Only profile(SCGCQ01213092)
 - MPI2.6: Mfg7 support for arbitrary starting slot number(SCGCQ01213267)
 - MPI 2.6: Add new firmware download type (CBB BACKUP)(SCGCQ01258005)
 - MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply(SCGCQ01002367)
 - MPI 2.5: Signed images for FWDownload(SCGCQ00469990)
 - MPI 2.5: Toolbox Console Text Display Tool(SCGCQ00415512)
 - Display the Storelib version in the show command.(SCGCQ01286063)
 - Unified StorCLI 7.1: PCIe Lane Speed and Link Configuration changes(SCGCQ01226457)
 - Unified StorCLI 7.1:OEL-Sparc support to Unified StorCLI(SCGCQ01196496)
 - Add support to allow Device names greater than 107(SCGCQ01039328)
 - Ventura : Add MR_ARRAY_EXT Support to StorCLI(SCGCQ01024636)
 - Enable SED on JBOD(SCGCQ00755527)
 - Allow VMWARE version of STORCLI cannot be run from any directory(SCGCQ00642230)
 - Added the OEM-NEC check for getting default disk-cache policy in Libmods as Disable.(SCGCQ00632051)
 - Request RAID CLI to display the Patrol Read Start Time(SCGCQ00564474)
 - Implemented the diag results to print on console(SCGCQ00525321)
 - MWCLI. R10, R50, R60, R00 VD creation(SCGCQ00369742)
 - MWCLI. Add HA support into storcli(SCGCQ00352120)
 - Create Spanned R0 array (00) in StorCLI(SCGCQ00350668)
 - Unified StorCLI 7.2:ARM-Linux support to Unified StorCLI(SCGCQ01241607)
 - Add NVMe device related changes(SCGCQ01034678)
 - Implemented the VD-VF mapping related commands in factory tool(SCGCQ00827665)
 - Complete 240VD support for utilities(SCGCQ00693042)
 - STORCLI will support MR controller management without UEFI BootServiceDriver Driver and also has retain functionality of existing seeadapter-through-driver functionality.(SCGCQ00621287)
 - dcmd path chagnes for supporting the new cachevault api(SCGCQ00381311)
 - Controller should not be reset after firmware download in CLI for SAS 3.5 Controllers(SCGCQ01399793)
 - Unified StorCLI 7.1:PPC Support(Big endian and Little endian) to Unified StorCLI(SCGCQ01196715)
 - Added the serial to properly log to the USB when the license is used for manufacturing the MFC on a controller.(SCGCQ01175821)
 - Unified CLI:Addition of appropriate device id's for Ventura(SCGCQ01132146)
 - LibMods: Increase maximum cache size for Cachecade to 2048GB. This will be named CC 2.5(SCGCQ00829204)
 - UDK Support for EFI(SCGCQ00795150)
 - Implemented the storcli command to print SATA drive's phy error counters and reset them.(SCGCQ00735171)
 - Consistent Sorting of Controllers for End Users in Customer Facing Tools(SCGCQ00696872)
 - Provide a way to enable or disable 512E using Applications(SCGCQ00351234)
 - Refer attached design doc(SCGCQ00349599)
 - Unified StorCLI : [Lenovo Purley] Adding tape drive support to Unified StorCLI for IT Ventura controllers.(SCGCQ01351495)
 - Unified StorCLI LibMods 7.1: Libmod changes for PCIe Lane Speed and Link Configuration(SCGCQ01227050)
 - Unified CLI changes to support host boot in MR with faulty FW(SCGCQ01093217)
 - Unified StorCLI:Implementing StoreLib IT static framework with StorCli(SCGCQ00916344)
 - LD Deletion stalling all IOs on Niwot HBA 12.12.0-0178(SCGCQ00757473)
 - RRB 71(SCGCQ00750164)
 - If any error that is returned as negative we return it s 0xFF from CLI to shell else FW returned error status will be returned to shell.(SCGCQ00665081)
 - SED/FDE changes for storcli Synchro(SCGCQ00632240)
 - ASD- StorCLI(SCGCQ00467863)
 - Implemented 128 drive support by using the new ENCL_INFO structures(SCGCQ00333209)
 - PERC 10 WIndows Support(SCGCQ01213160)
 - PERC 10 WIndows Support(SCGCQ01213157)
 - LibMods-Porting of MR6.x changes to Ventura(SCGCQ01109080)
 - Megacli/storcli support for lmrc driver(SCGCQ00433703)
 - PR SCGCQ00319011: Rebuild time reset(SCGCQ00381093)
 - Uneven span support is added in StorCLI.(SCGCQ00349548)
 - Unified StorCLI 7.1-Phase 2:IT Firmware downgrade support to Unified StorCLI(SCGCQ01224391)
 - Add EFI support for the manufacturing command to program.(SCGCQ01191095)
 - Ventura : Add IT Support to StorCLI [Checking in LIBMODS Changes ](SCGCQ00859216)
 - Storcli Should display SAS Address N/A if its invalid and change Host interface type names from PCIX, PCIE to PCI-X, PCI-E(SCGCQ00828476)
 - Monitoring Drive performance and predictive failure(SCGCQ00817977)
 - While saving and Restoring the configuration on controller we used to save MR_CONFIG_DATA and MR_CTRL_PROP. Added the below(SCGCQ01234118)
 - Unified StorCLI 7.1:FreeBSD OS support to Unified StorCLI 7.1(SCGCQ01191237)
 - LimMod changes related to CtrlH & MSM Mismatch on write-back options(SCGCQ00818987)
 - Functionality to extract field value from new API changes(SCGCQ00794841)
 - MR 4.12: Big endian architecture support for MR Linux driver and StorCli(SCGCQ00558815)

0007.0057.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------
Enhancement:
- Added support for ThinkSystem HBA and RAID.

1.20.20 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed an issue where command "/cx show alilog d:/logfile=xyz.txt" reports success even when destination doesn't have enough space to save log file - (SCGCQ00861227)
- Fixed an issue where command "/c0/pall show" does not show Port number and whether the Port is valid - (SCGCQ00865335)
- Fixed an issue where command "/c0/epd0,1 show" doesn't report epd1 as invalid - (SCGCQ00908866)
- Fixed an issue where command "/c0 show bootdrive" doesn't display EPD for EPDs - (SCGCQ00918811)
- Fixed an issue where command "/c0/fall show" succeeds but "/c0/fall show all" fails- (SCGCQ0043074)
- Fixed an issue where command "/c1/e83 show status" may show "Unsupported" in many fields - (SCGCQ00950438)
- Fixed an issue where command "storcli /c0/d1 set transport=on sdhsp=on" uses a dedicated hotspare even though the command requests a shared hotspare - (SCGCQ00981663)
- Fixed an issue where an incorrect message may occur when creating a RAID5 - (SCGCQ00995140)
- Fixed an issue where command "/c0/cv start retentiontest" may result in an extra "File Write ERROR !!!" print - (SCGCQ00997401)
- Fixed an issue where an incorrect failure message may occur when creating a RAID1 with 3 drives - (SCGCQ00999258)
- Fixed an issue where Virtual Drive policy isn't retained after firmware flash fails - (SCGCQ01000358)
- Fixed an issue where storcli does not display description on command success - (SCGCQ01023973)
- Fixed an issue where "force" argument may not work with "parallel" argument - (SCGCQ01026081)
- Fixed an issue where command "/c0 show autoconfig" may result in empty values - (SCGCQ01026945)
- Fixed an issue where unable to set multipath parameter when firmware returns "MFI_STAT_OK_REBOOT_REQUIRED" - (SCGCQ01029534)
- Fixed an issue where command "/c0/eall/sall download src=H7280A520.P551 parallel" may report failure and success, when the flash has failed - (SCGCQ01030430)
- Fixed an issue where Mode 5 firmware download is not working with "parallel" argument - (SCGCQ01030535)
- Fixed an issue where storcli reports "Succeeded" instead of "Initiated" during a PD firmware flash status check - (SCGCQ01031218)
- Fixed an issue where storcli shows an incorrect error message when trying to remove the Blocked Access from SVDs - (SCGCQ01039102)
- Fixed an issue where storcli only shows firmware flash status for the last drive when multiple drives are being flashed simultaneously - (SCGCQ01039484)
- Fixed an issue where storcli does not give context-specific output for storcli help commands - (SCGCQ01039534)
- Fixed an issue where command "/c0 h" does not work - (SCGCQ01039745)
- Fixed an issue where command "/c0/cv start learn" may result in an incorrect message if the learn cycle fails - (SCGCQ01039757)
- Fixed an issue where Mode F is not fired after Mode E when "activatenow" is specified with no delay - (SCGCQ01052895)
- Fixed an issue where storcli did not disable offline commands and exit when Mode E or Mode F firmware download fails - (SCGCQ01053068)
- Fixed an issue where the entire error message is not shown when trying to update the security key "rekeyLock" - (SCGCQ01059105)
- Fixed an issue where JBOD status is shown under EPD column when displaying the status message - (SCGCQ01062314)
- Fixed an issue where "Segmentation fault" error may occur when creating and deleting multiple VDs in a loop - (SCGCQ01062646)
- Fixed an issue where an saving logs to an invalid destination does not cause an error - (SCGCQ01063899)
- Fixed an issue where JBOD information is displayed in EPD mode - (SCGCQ01064101)
- Fixed an issue where MFC_DEFAULTS are not handled correctly during VD creation - (SCGCQ01070120)
- Fixed an issue where "Failed operation not possible for current RAID level" error may occur when the error should have been "resources already in use" - (SCGCQ01073669)
- Fixed an issue where multi init parameter help syntax was missing - (SCGCQ01078997)
- Fixed an issue where storcli might crash when more than 200 characters are in the command - (SCGCQ01081082)
- Fixed an issue where extra prints and incorrect messages may occur while flashing PD firmware on SAS and SATA drives at the same time - (SCGCQ01091011)
- Fixed an issue where help did not include VFQDMode values and their explanations - (SCGCQ01128071)
- Fixed an issue where command "/c0/vall set pi=off" can error even though the command was successful - (SCGCQ01133117)
- Fixed an issue where output of show init/erase operation lists as VD instead of EPD - (SCGCQ00935416)
- Fixed an issue where multiple entries of the same object in a single command still results in success - (SCGCQ00947387)
- Fixed an issue where virtual drive may disappear after starting an erase on a RAID0 VD in simple and normal mode - (SCGCQ00995154)
- Fixed an issue where command "/c0/vall set hidden=on" or "/c0/vall set hidden=off" may error even on success - (SCGCQ01026907)
- Fixed an issue where "behavior" may appear as "behaviour" - (SCGCQ01029447)
- Fixed an issue where command "/c0 show events" errors even when successful - (SCGCQ01030139)
- Fixed an issue where storcli may ask for a system reboot if changing behavior from EPD to RAID0 - (SCGCQ01035493)
- Fixed an issue where storcli may not display "behavior mode" after setting the behavior mode - (SCGCQ01035500)
- Fixed an issue where command "/cx show preservedcache" may result in a "Segmentation fault" error when pinned cache is present - (SCGCQ01036028)
- Fixed an issue where command "/c0 show phyerrorcounters" shows success without printing the table - (SCGCQ01038669)
- Fixed an issue where MRI mode is taking any value and not reflecting - (SCGCQ01039536)
- Fixed an issue where command "/cx show alilog" calculates Leap Year incorrectly - (SCGCQ01039554)
- Fixed an issue where command "/c0/fall del" may not show correct error message when controller has pinned cache and is in Safe Mode  - (SCGCQ01043063)
- Fixed an issue where controller reset command was not blocked in EFI environment - (SCGCQ01052322)
- Fixed an issue where the copyright date showed 2015 instead of 2016 - (SCGCQ01053608)
- Fixed an issue where command "storcli /c0 /v0 start erase simple patterna=1" is not setting the pattern - (SCGCQ01057994)
- Fixed an issue where "/c0 set pcilinkspeed=3" command reports success even when the command isn't sent to firmware - (SCGCQ01058298)
- Fixed an issue where MFG data shows success when inputting an invalid file - (SCGCQ01058300)
- Fixed an issue where JBOD is being displayed when querying EPD information - (SCGCQ01059088)
- Fixed an issue where error "Snapshot is enabled on the Virtual Disk" may occur when creating and deleting multiple VDs in a loop - (SCGCQ01060805)
- Fixed an issue where "show BBMT" may show information for EPDs - (SCGCQ01064035)
- Fixed an issue where error "Invalid RAID level" may be shown instead of "Cannot create raid level with 1 span" - (SCGCQ01064084)
- Fixed an issue where SATA SSD firmware cannot be flashed - (SCGCQ01085706)
- Fixed an issue where storcli does not handle the return status properly during controller firmware flash - (SCGCQ01132613)
- Fixed an issue where command "storcli /c0/v1 start migrate type=raid1 option=add drives=120:5,7" may fail - (SCGCQ00879775)
- Fixed an issue where EPD-specific operations may not work - (SCGCQ00892973)
- Fixed an issue where delete EPD command may show Delete VD success message instead of Delete EPD success - (SCGCQ00905830)
- Fixed an issue where reboot required message may not occur when toggling SRIOV - (SCGCQ00919940)
- Fixed an issue where pinned cache of EPD may generates a listing as a Virtual Drive in the preserved cache message - (SCGCQ00988786)
- Fixed an issue where storcli may fail to set JBOD=off when there are no JBODs - (SCGCQ00993464)
- Fixed an issue where force flash may not work with resetnow opton - (SCGCQ00993466)
- Fixed an issue where storcli command for bbu may not read the SuperCap VPD information properly - (SCGCQ00994876)
- Fixed an issue where storcli may error "Resource already in use" when trying to configure RAID0 with online PDs - (SCGCQ01003415)
- Fixed an issue where storcli may not be able to change the behavior mode - (SCGCQ01023985)
- Fixed a typo in remaining time when issuing command "/cx/bbu show" - (SCGCQ01024968)
- Fixed an issue where printf may be seen in libmods in power-on-hours command - (SCGCQ01033027)
- Fixed an issue where storcli may not show an error when deleting security key fails - (SCGCQ01039756)
- Fixed an issue where "/c0/dall set" command may report success even though the command is incomplete - (SCGCQ01052306)
- Fixed an issue where command "/c0 dall show" may hang or throw an exception - (SCGCQ01052841)
- Fixed an issue where command "/c0 show" may display JBOD list when the behavior is set to EPD - (SCGCQ01052876)
- Fixed an issue where command "/c0 show memscribpatterns" status may report success but description says failed - (SCGCQ01058525)
- Fixed an issue where a "Synchronous Exception" may occur when running command "/c0 set vpd" with an incorrect input file - (SCGCQ01059798)
- Fixed an issue where storcli may throw an inappropriate error when trying to flash the wrong drive firmware to a drive - (SCGCQ01065620)
- Fixed an issue where drive firmware flash with parallel option may return error code 18 - (SCGCQ01066204)
- Fixed an issue where storcli may display Nytrocache even when controller does not support it - (SCGCQ01067274)
- Fixed an issue where storcli set JBOD as boot drive and removing JBOD as boot drive may display different messages - (SCGCQ01079667)
- Fixed an issue where connector name may not be sorted properly - (SCGCQ00890604)
- Fixed an issue where command "/c0/epd20 del" may not throw error when EPD is not present - (SCGCQ00904055)
- Fixed an issue where stop erase help file may show incorrect syntax - (SCGCQ00910533)
- Fixed an issue where host name and operating system details may show client machine instead of host machine - (SCGCQ00910614)
- Fixed an issue where storcli may misspell "controller" when flushing controller - (SCGCQ00973474)
- Fixed an issue where setting Consistency Check mode may fail if no start time given, and may set successfully if wrong time is given - (SCGCQ01039758)
- Fixed an issue where some commands may not report success on success - (SCGCQ01050695)
- Fixed an issue where storcli may show the wrong message when boot drive is cleared on all drives - (SCGCQ01053241)
- Fixed an issue where "/c0/vall show all" has an inaccurate description - (SCGCQ01058116)
- Fixed an issue where an extra space may appear in the message "Flash image is not supported , Try force." - (SCGCQ01064773)
- Fixed an issue where a SAS Address mismatch may occur after setting SAS Address from storclio - (SCGCQ01082500)
- Fixed an issue where storcli may show SDS reference and multiple modes for personality switch - (SCGCQ01127378)
- Fixed an issue where help output is not available for "/c0 add jbod h" - (SCGCQ01131493)
- Fixed an issue where command "/c0/epd4 del discardcache" may throw a syntax error - (SCGCQ00904205)
- Fixed an issue where error "Add EPD failed" may occur when creating an EPD - (SCGCQ00908864)
- Fixed an issue where Auto Config option MRIE-Mode may not be SMARTMODE - (SCGCQ00922540)
- Fixed an issue where EPD may not be allowed in JBOD mode - (SCGCQ01050766)
- Fixed an issue where the table may show EPD instead of JBOD - (SCGCQ01058178)
- Fixed an issue where error " segmentation fault " may occur - (SCGCQ01063305)
- Fixed an issue where command "set cc" may fail even though cc was set successfully - (SCGCQ01074482)
- Fixed an issue where installation of storclio may fail with syntax error - (SCGCQ01074514)
- Fixed an issue where a personality switch from JBOD to EPD may not clear JBOD and EPD config - (SCGCQ01080493)
- Fixed an issue where "delete preservedcache" option may not be listed in the help menu "/c0/vx delete h" - (SCGCQ00924642)
- Fixed an issue where storcli may crash when trying to attach a CacheCade Virtual Drive to source Virtual Drive. (SCGCQ00934528)
- Fixed an issue where there may be no error message for failure to initialize EPD - (SCGCQ00935477)
- Fixed an issue where installaton of storclio may fail - (SCGCQ00952422)
- Fixed an issue where references of epdpassthru were not JBOD - (SCGCQ01023981)
- Fixed an issue where command "/c0/vall show bbmt" may not display the corrected and uncorrected values - (SCGCQ01059790)
- Fixed an issue where command "/c0/vall set ssdcaching=on/off" may not apply to all the Virtual Drives - (SCGCQ01060315)
- Fixed an issue where command "/c0/delete config" output may not be consistent - (SCGCQ01091178)
- Fixed an issue where description of "add epd" may not state success or failure - (SCGCQ00908865)
- Fixed an issue where EPD details may not show in "show all" command  - (SCGCQ00921937)
- Fixed an issue where BIOS mode may not be able to be changed by storcli - (SCGCQ01058624)
- Fixed an issue where setting lowlatency to OFF, the multipath setting is changed to OFF as well - (SCGCQ01080489)
- Fixed an issue where storcli may crash when issuing command "/c0/vall show" - (SCGCQ00888330)
- Fixed an issue where drive microcode update to directly attached drives may fail in default mode - (SCGCQ00888837)
- Fixed an issue where command "/c0/vall del" may delete EPDs as well - (SCGCQ00915484)
- Fixed an issue where SRIOV may not be enabled by storcli - (SCGCQ00915697)
- Fixed an issue where storcli may continue to prompt even when force option is used for controller firmware flash - (SCGCQ01060461)
- Fixed an issue where connector name for first 8 PHYs of enclosure may not be displayed as expected - (SCGCQ00953464, Port of SCGCQ00890597)
- Fixed an issue where description status in failure message of EPD delete may not be accurate - (SCGCQ01015016, Port of SCGCQ00988760)
- Fixed an issue where factory defaults may not be aligned with the new API - (SCGCQ01044939, Port of SCGCQ01044891)
- Fixed an issue where phyerrorcounters command may not display any PHY Error Counter values - (SCGCQ01049064, Port of SCGCQ01028993)
- Fixed an issue where "show" command may fail - (SCGCQ01004630, SCGCQ01006038, Port of SCGCQ01004617)
- Fixed an issue where command "/call show logfile=filename" may result in error "segmentaton fault"  - (SCGCQ01020010, Port of SCGCQ01019547)
- Fixed an issue where command "/c0 show dequeuelog file=filename.txt" may result in error "Segmentation fault(Core Dump)" - (SCGCQ01061120, Port of SCGCQ01014212)
- Fixed an issue where transport command may include "all" when only "shared" is requested - (SCGCQ01093159, Port of SCGCQ01093145)
- Fixed an issue where command "/c0 show alilog" may result in error "Segmentation fault(Core Dump)" - (SCGCQ01015017, Port of SCGCQ01014101)
- Fixed an issue where the hide and unhide options may not be available for a disk group - (SCGCQ01050234, Port of SCGCQ01050181)
- Fixed an issue where storcli may not generate a log - (SCGCQ00998150, Port of SCGCQ00945177)
- Fixed an issue where Global Hotspares may show as TR in disk group query - (SCGCQ01047957, Port of SCGCQ01047789)
- Fixed an issue where command "/bbu show all" may show "Remaining Time Alarm = Yes" even when not applicable  - (SCGCQ01143941, Port of SCGCQ01026187)
- Fixed an issue where maintainer name may not be populated when querying storcli version information from operating system - (SCGCQ00912697, Port of SCGCQ00838307)
- Fixed an issue where an invalid error message "Device is expander; use /c0/xp download" may be displayed on expander firmware download  - (SCGCQ01110108, Port of SCGCQ00934755)
- Fixed an issue where Virtual Drive number is not sorted in "/c0/vall show vfmap" command output - (SCGCQ00932799, Port of SCGCQ00929211)
- Fixed an issue where storcli may fail to correctly populate log files - (SCGCQ01079016, Port of SCGCQ01074584)

Enhancements:
- Added the personality change command was not present - (SCGCQ00850610)
- Extended the VFMaping to the max VFs suported by the adapter dynamically - (SCGCQ00868220)
- Added multipath support in EPD configuration options - (SCGCQ01015758)
- Added additional CPU support on EFI platform - (SCGCQ01026250)
- Added command to display progress of Patrol Read on a Physical Drive - (SCGCQ01040304)
- Added personality change features - (SCGCQ01111930)
- Added VF-queue depth mode settings - (SCGCQ00907072)
- Added ability to enable firmwre debug via storcli without UART - (SCGCQ00908320)
- Added Secure Erase support to JBOD and System drives - (SCGCQ00929757)
- Added a JBOD entity for various operations - (SCGCQ01047229)
- Added EPD support of setting EPD configuration parameter options - (SCGCQ00907064)
- Added more specific error messages in some circumstances - (SCGCQ00920034)
- Added new compilation environment and makefiles - (SCGCQ00920058)
- Added EPD and EPD-passthrough and single-drive RAID0 modes to eSDS - (SCGCQ01015739)
- Added support for drive microcode update Modes E and F - (SCGCQ01047223)
- Added code to display JBOD personality - (SCGCQ01146775)
- Updated existing implementaton to disable thermal polling in some circumstances - (SCGCQ01154338)
- Added new erase type called Crypto - (SCGCQ01050618)
- Added new command to set the multiInit EPD parameter - (SCGCQ01080273)
- Added support for drive microcode update through parallel loading - (SCGCQ01024964)
- Added support for EPD creation - (SCGCQ00887664)
- Modified a failure message to "This command only applies to Nytro Megaraid controllers. All others will display a failure status." - (SCGCQ01004610, Port of SCGCQ00881414)


1.18.11 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed issue where FW could be downleveled without using the noverchk flag (SCGCQ00924705)
- Fixed inaccurate message displayed while deleting a Cachecade Virtual Drive (CCVD) (SCGCQ00897785)
- Fixed issue where physical disk (PD) FW upgrade would fail with some SATA drives (SCGCQ00873612)
- Fixed issue where StorCLI failed to dump lastoneday pdfailevents in a file (SCGCQ00853196)
- Fixed issue where StorCLI was not reporting command success for a StorCLI64 /c0 show events file=eventLog.txt command (SCGCQ00851339)
- Fixed issue where StorCLI would not find enclosures in multipath environment (SCGCQ00873620)

Enhancements:
- Updated the BBU-properties in /c0/bbu show all (BBU learn mode) (SCGCQ00904662)
- Added the support to set and clear the transport on a DG (SCGCQ00920046)
- Added the support to change the large queue depth ctrl property in StorCLI (SCGCQ00933318)
- Implemented commands to save/restore the configuration on the controller. (SCGCQ00851795)
- Add support to detect that an OS is installed on a JBOD and to block it from being changed to Unconfigured Good (SCGCQ00828030)
- Provide a more descriptive port enumeration (SCGCQ00854620)
- Add support to enable/Disable of Large IO Support (SCGCQ00894644) 

1.16.14 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed an issue where no error message would occur when attempting to create a VD with Write-Back policy on a controller that does not support Write-Back - (SCGCQ00885617)
- Fixed an issue where StorCli would report "not in progress" for a rebuild instead of "paused" - (SCGCQ00907176)
- Fixed an issue where Foreign VD count of a spanned drive group is reported twice - (SCGCQ00911715)
- Fixed an issue where an invalid error "Device is expander,; use /c0/xp download" would occur when updating expander firmware - (SCGCQ00934755)

1.16.10 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed an issue where no StorCLI error message is displayed when attempting to create a VD with WB policy on iMR HBA (SCGCQ00885617)
- Fixed an issue where controller status shown between MSM and StorCLI may contain false flash errors (SCGCQ00888470)
- Fixed an issue StorCLI PD firmware upgrade fails due to ATA Passthrough command being built incorrectly for download microcode (SCGCQ00862914)
- Fixed an issue StorCLI does not display E252/E253 enclosure info on an 84016 SCGCQ00868143)
- Corrected StorCLI behavior and messages between consecutive expansion operations of RAID Volume (SCGCQ00870429)
- Fixed an issue RAID level migration is not happening from 0 to level 1(SCGCQ00873770)


1.14.12 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Incorporated StorCLI MegaRAID 6.6 stream

Enhancements:
- Added ability to print SATA drives phy error counters and reset them (SCGCQ00735171)
- Added consistent sorting of controllers using bus, device, function (SCGCQ00696872)
- Added ability to enable or disable 512e support (SCGCQ00351234)
- Added support for Self-Encrypting Drives in JBOD mode (SCGCQ00755527)
- Added ability for VMWare version to be run from any directory (SCGCQ00642230)
- Added ability to display NCQ enabled/disabled status of every SATA drive (SCGCQ00564477)
- Added ability to create a RAID00 (SCGCQ00350668)
- Added ability to display the Patrol Read Start Time (SCGCQ00564474)
- Added learn cycle progress information in show learn command (SCGCQ00644984)
- Added support for uneven spans (SCGCQ00349548)
- Added support for lmrc driver (SCGCQ00433703)
- Added 240 Virtual Drive support (SCGCQ00693042)
- Improved Punctured Block logging (SCGCQ00342399) 

1.12.15 - Moderate Impact/Low Probability of Occurrence
-------
Fix(es):
 - Prevent storCLI from allowing users to enable JBOD mode on
   controllers that do not support JBOD mode.
 - Updated CACHEBYPASS command to line up with user expectation.  When CACHEBYPASS is set, the user wants the cache to be bypassed. In previous versions of storcli, setting CACHEBYPASS actually disables the bypass.

1.07.07 - Moderate Impact/Low Probability of Occurrence
-------
Enhancement(s)
 - Added support for ServeRAID M1215 SAS/SATA Controller
Fix(es):
 - Fixed an issue where segmentation faults may occur in Linux.
 - Added help information for resolving vd creation command fails with 'Memory Exhausted' message in SLES 11 OS.
 - Fixed an issue where estimated time left, which range from seven or more days for Consistency Check and rebuild operations, are not displaying.

1.04.07 - Moderate Impact/Low Probability of Occurrence
-------
Enhancement(s)
 - Added support for ServeRAID M5210e and ServeRAID M5210
Fix(es):
 - Fixed an issue where a command failure results in subsequent commands and actions failing.
 - Fixed an issue where storCLI reports a segmentation fault when running the command to downgrade the controller to iMR.
 - Added help file for for storcli /cx/dx set security
 - Fixed an issue where the "show ctrlcount help" command is not displaying properly.
 - Fixed an issue where a failure is displayed in the output for querying dimmer switch information.
 - Fixed an issue where the user is not able to set securitykey on a controller, if the securitykey was set through MSM.
 - Fixed an issue where the virtual drive creation command does not give any error message when the user tries to create a private information virtual drive using normal physical drives.
 - Fixed an issue where starkly displays a firmware flash successfully completed message even though the flashing failed.
 - Synced the pause pr command with show pr command to show correct PR Current State.
 - Fixed an issue where enabling online controller reset rate (OCR) from storCLI actually disables the controller property.

1.03.11 - Initial release
-------





Lenovo Data Center Group Linux OS Support Home Page
linux.lenovo.com

© 2018-2022 Lenovo. All rights reserved