Lenovo Storage Host-Bus-Adapter (HBA) Firmware
ThinkSystem 440-x SAS/SATA 12Gb HBA Firmware and BIOS Update
Supported Adapters:
ThinkSystem 440-16e SAS/SATA PCIe Gen4 12Gb HBA for 4Y37A09724
ThinkSystem 440-16i CFF SAS/SATA PCIe Gen4 12Gb Internal HBA for 4Y37A09725
ThinkSystem 440-8i SAS/SATA PCIe Gen4 12Gb HBA for SR17A98375
ThinkSystem 440-16i SAS/SATA PCIe Gen4 12Gb HBA for SR17A98376
ThinkSystem 440-8e SAS/SATA PCIe Gen4 12Gb HBA for 4Y37A78837
NOTE TO SERVICE - Reference RETAIN #N/A
Version 27.125.10.00
---------------
BIOS Firmware UEFI Driver
9.53.00.00 27.00.01.00 27.00.00.00
Defects:
-95XX card: When JBOD Expanders are periodically reset, drive in a large topology may go missing.(DCSG01644273 (Port Of Defect DCSG01592213))
Version 27.125.09.00
---------------
BIOS Firmware UEFI Driver
9.53.00.00 27.00.00.00 27.00.00.00
Defect:
-Possible division or modulo by zero in enclosure management code..(DCSG01224310)
-[Code Coverage] SCSI to NVMe translation test failed in BST.(DCSG01252405)
-9500-16i - The C_TYPE sideband signals of the connector are not driven to Low.(DCSG01379243)
-Build all failed on firmware tip code.(DCSG01343959)
-SPILIB2: SPI Emulation Erases the wrong section.(DCSG01049441)
-HBA discovery failed with Phase 24 Storelib and StorelibTest.(DCSG01207008)
-SPILIB2: Fix offsets in SPI2_LIB_DEVICE_PARAMS.(DCSG00428841)
-[SATA Only] NCQ Errors observed with running Read/Write IOs along with SCSI Unmap.(DCSG01254091)
-Firmware reports dual ports for SATA drives..(DCSG01352291)
-Variable type, Pointer is used as argument to sizeof function in SCSI to NVMe translation for complete log sense handler.(DCSG01385273)
-SAS drive keeps failing SCSI TUR with Check condition due to Controller not sending Periodic Notify (Enable Spinup.(DCSG01232852)
-Firmware was not repairing an NVMe drive with detached Inactive Namespace..(DCSG01321255)
-Wrong expected sense data in invalid CDB test for NVMe drive.(DCSG01252944)
-Hardware Workaround:Link between Controller and expander not always recovering after link reset.(DCSG01196230)
-Disable SATA protocol when in optical mode.(DCSG01194126)
-Locate LED operation does not work for NVMe drive slot on UBM backplane.(DCSG01230479)
-Same slot number is assigned to x1 link width drives connected to consecutive controller PHYs when an I2C backplane detection.(DCSG01375808)
-Firmware is not incrementing the DFC Change Count value when there is a DFC change detected by the firmware..(DCSG01287092)
-SPILIB2 : Watchdog reset due to ARM Exception while flash under stress.(DCSG00814654)
-9500 Series- host with eight PHY controller hangs during warm reboot.(DCSG01289054)
-[Aero/Ventura] Add check for Sense Data size.(DCSG01178348)
-Build all failed on firmware tip code.(DCSG01381053)
-LBA information missing from sense data with Medium Error Sense Key for SATA drives.(DCSG01183332)
-SPILIB2: Series 9700 Chip Select Timing registers default to zero.(DCSG01182027)
-[BST] "Invalid SCSI CDBs" test failed for NVMe Format unit commands in older firmware versions.(DCSG01287310)
-Uninitialized scalar variable access in UBM Backplane management and I2C driver code..(DCSG01339421)
-NVMe device connected to PCIe switch is not discovered by controller firmware on boot up.(DCSG01260624)
-NVMe Encapsulated MPI command not failed when it is blocked by IO Unit Page 13..(DCSG01294635)
-SPILIB2: (Margay Only) ARM Exception while flash under stress upon closing telnet.(DCSG00914933)
-Firmware console command 'pl eminfo' shows no PCIe support for a PCIe supported UBM backplane Device Face Connector.(DCSG01285442)
-IT controller firmware sending MCTP version numbers in reverse order.(DCSG01234654)
-Aero: Incorrect topology phys memory allocation.(DCSG01185588)
-Uninitialized pointer access in UBM Backplane management code.(DCSG01225064)
-Reading IO Unit Page 13 returns junk data.(DCSG01292339)
-Build all is failed due to Error: NVDATA Major Versions do not match!.(DCSG01258017)
-C0:[141]:[Error] Signing Buffer Failed Sts:2 mesg after import successfully the certificate and reboot.(DCSG01270486)
-Self test aborts when Open Zone command issued on a Security locked drive.(DCSG01194141)
-observed when diagnostic register dump is performed while running IO to the drives. Description Of Removed RxEEDP Buffer dump from the diagnostic register dump..(DCSG01227332)
-[NVMe] Mode F Firmware download to certain NVMe drives fails..(DCSG01286617)
-[Code Coverage] NVMe stress test - NVMe PRP Firmware validation.(DCSG01260284)
-BST script failed to invoke utilities.(DCSG01357327)
-Io Unit Control with Remove device fails if MPI function blocking is enabled. IO Unit Page 13 is writeable..(DCSG01270812)
-Phase 24 Code analysis tool Defects related to SPDM.(DCSG01224346)
-Target mode controller port width degrades following host resets/power cycles with autoport config disabled.(DCSG01325599)
-[SATA] SATA Initialization fails on certain large capacity SATA drives.(DCSG01194600)
-Firmware summary notes needs to be updated to remove 94xx boards references.(DCSG01271551)
-QErr value in Control mode page for NCQ SATA devices is set to 0 instead of 1.(DCSG01375632)
-Erase operation fails on OEM specific UBM backplane during UBM controller firmware update.(DCSG01289710 (Port Of Defect DCSG01294066))
-[NVMe] Some NVMe drives do not link up on certain OEM backplanes..(DCSG01193134 (Port Of Defect DCSG01196465))
-Direct attached devices do not link up in case SEP backplane detection is configured in NVData.(DCSG01285763 (Port Of Defect DCSG01286648)
-Revert SATA Init timeout changes.(DCSG01252414 (Port Of Defect DCSG01255751)
-Change spinup mode while SATA link rese.(DCSG01161733 (Port Of Defect DCSG01231494))
-Update NVDATA Major version.(DCSG01258013 (Port Of Defect DCSG01270040))
-Sanitize (Block Erase) along with shutdown sequence caused assertion in firmware. (NVMe Only).(DCSG01358573 (Port Of Defect DCSG01371174))
-IOC Page 7 does not report the updated "SASNotifyPrimitiveMasks".(DCSG01220829 (Port Of Defect DCSG01222353))
-SATA, Fault 0x5919 seen during write same error and task managements.(DCSG01176562 (Port Of Defect DCSG01228270))
-M.2 NVMe drive initialization failed after warm reset.(DCSG01264359 (Port Of Defect DCSG01301951))
-[VSes] Number of slots reported incorrectly in certain OEM backplane.(DCSG01200427 (Port Of Defect DCSG01215896))
-NVDATA major version was updated to be same as Phase Version.(DCSG01477125)
-95xx]: Log sense page 0x15 fails on ACS-5 supported SATA drive..(DCSG01458189)
-PL firmware not failing NVMe self-test when already an existing NVMe self-test command.(DCSG01459189 (Port Of Defect DCSG01350001))
-SCSI Self-Test Results (0x10) log page not updating status when self-test in progress.(DCSG01466802 (Port Of Defect DCSG01072582))
-[9500 BST] Reading the Backplane FRU data causing the NVMe drive link to go down fo.(DCSG01420775)
-[95xx]: Incorrect slot number management for non-UBM backplanes.(DCSG01451450)
-A target reset Task Management to a direct attach SAS drive may not go out to the drive even.(DCSG01432770 (Port Of Defect DCSG01419839)
-EDSFF drive in UBM will not link up and Change Detect polling may not happen for some.(DCSG01417264)
-[95xx] - Slot numbering for NVMe devices connected behind an invalid backplane shown.(DCSG01442157 (Port Of Defect DCSG01436490))
-[9500/02] Update Combo Serdes Wrapper M0 code.(DCSG01431077)
-BST: Added NVMe test for SCSI Immediate Command translation.(DCSG01372972)
-Support generation code feature in MPI SEP request handler.(DCSG01420969 (Port Of EnhancementRequest DCSG01417694))
-Map valid slots to its corresponding element index in subsequent MPI SEP request.(DCSG01420988 (Port Of EnhancementRequest DCSG01418309))
EnhancementRequests:
-Add IO Unit page 13 handling to Block/Allow MPI functions.(DCSG01214245)
-Implement incomplete firmware handlers for the SCSI commands as per the latest.(DCSG01308277)
-SPILIB2: Add support for high impedance dummy cycles in 9700 Series.(DCSG01118681)
-BST bring up on Windows server.(DCSG00021431)
-SPILIB2: Add support for new Cypress parts via proprietary CFI Method.(DCSG00734502)
-Updated setup hardware configuration in BST scripts.(DCSG01352775)
-SPILIB2: Add support for bulk erase.(DCSG01061535)
-Updated release scripts for verifying Firmware build status.(DCSG01350607)
-SPILIB2: Update python decoder with latest fixes.(DCSG01091175)
-Firmware: Implement REFCLK control in HII.(DCSG01291368)
-SPILIB2: Configure Series 9700 NVSRAM hardware to send Write Enable on first.(DCSG01131779)
-IT NVDATA: Update phase 26 NVDATA major version.(DCSG01386930)
-[SNTL] Update SCSI Format Translation for NVMe devices.(DCSG01137935)
-SPILIB2: Add new configuration bits to the init interface for SPI Flash drive strength.(DCSG01015117)
-Aero - SecureBoot: Added debug messages to the ring-buffer when the FW download.(DCSG01132478)
-Aero FW-Download: when writing bootloader to the main region, write the signature.(DCSG01154887)
-SPILIB2: Add MRAM and optional parameters file to CVS decoder.(DCSG01128295)
-SPILIB: Add support for Hybrid topology CFI parts.(DCSG00782279)
-Discontinue Firmware Release for 94xx Series of chips.(DCSG01240537)
-SPILIB2: Add serial mode support for SPI devices with read only Quad Enable bits.(DCSG00916467)
-PL Firmware: SFF-TA-1005 Version 1.4 Support.(DCSG01214256)
-BST bring up on Linux server.(DCSG01267771)
-Update createSasversion.exe to use getCreds.(DCSG00131581)
-Updated Package build option in release scripts.(DCSG01360774)
-SPILIB2: Eliminate incompatible erase commands in MultiErase mode.(DCSG00830450)
-Code Coverage] Additional SCSI to NVMe translation tests in BST scripts.(DCSG01142852)
-SPILIB2: Support for Additional SPI Clock Frequencies.(DCSG00424412)
-SPILIB2: Support ECC for Margay.(DCSG00429625)
-SPILIB2: 9700 Series core needs maximum continuous count initialized earlier.(DCSG01170965)
-Firmware: Support Long Lock Delay Times when Negotiating to a 6G SATA Driv.(DCSG01253833)
-SPILIB: Add Python-Based Logic Analyzer Decoder.(DCSG00980221)
-SPILIB2: Add support for serial mode for parts with QE=1 and dual mode support.(DCSG00831421)
-Use event based wait for browser automation during release process.(DCSG01133010)
-Upgrade ARM compiler version.(DCSG01331364)
-SPDM library: Add support for SPDM v1.0.(DCSG01137730)
-SBLIB: Clean up code for external use.(DCSG01150489)
-Update SB Lib to latest.(DCSG01224363)
-SPILIB2: Update Series 9700 SPI headers to latest.(DCSG01132011)
-SPILIB2: Port all changes AV1 to AV2 for manual access files.(DCSG00917802)
-SPILIB: Update Series 9700 header file.(DCSG01117315)
-Firmware: Enhanced NVMe Recovery Process.(DCSG01220515)
-Add ApSHA changes.(DCSG01209350)
-SPDM: Upgrade the latest SPDM Library in PH26.(DCSG01219141)
-SPILIBAV2: Misc. updates to Avenger2 SPI code for FPGA.(DCSG01057329)
-Update SPI Lib to latest.(DCSG01215946)
-[Code Coverage] Include CTC files in firmware code and create a build type that.(DCSG01132120)
-SPILIB: Update build scripts for ADS.(DCSG00943761)
-SPILIB2: Add High Level SPI Emulation Library.(DCSG00508974)
-PL firmware workaround for UBM Backplane firmware flashing issue in OEM specific.(DCSG01237118 (Port Of EnhancementRequest DCSG01252393)
-PL: Enable the UBM firmware update support for OEM specific UBM backplane.(DCSG01233264 (Port Of EnhancementRequest DCSG01252355))
-IOP: Rework MCTP packet validation code for workaround for some multi-segment.(DCSG01289379 (Port Of EnhancementRequest DCSG01328386))
-9500] Add support for host phys/lanes in Port Status Green GPIO.(DCSG01207029 (Port Of EnhancementRequest DCSG01251940))
-Add support for new product specific MCTP Event.(DCSG01149990 (Port Of EnhancementRequest DCSG01268764)
-Add support for OEM specific SAS 4 expander based enclosure with 950x controllers.(DCSG01351490 (Port Of EnhancementRequest DCSG01363691))
-LCS work around in PL firmware to be made generic for all models of an OEM specific UBM.(DCSG01452718 (Port Of EnhancementRequest DCSG01446403))
-BST: Added NVMe test for SCSI Immediate Command translation.(DCSG01372972)
-Update Secure boot Library in Firmware.(DCSG01445968)
-Buffer overrun on Request Sense to an NVMe device.(DCSG01428721 (Port Of Defect DCSG01425345)
-[HBA 95xx]: Set LSI-bit to one in the Device info field for Broadcom expander device type.(DCSG01418828)
-[9500 PL] Spinup handling when rising edge and falling edge spinup interrupts are set simultaneouly.(DCSG01373049)
-[9500 PL] Add addition debug data on detecting Link Hang interrupt.(DCSG01376930)
-Increased SATA Initialization timeout and made it configurable by NVDATA.(DCSG01383806)
-PL: Add NVDATA switch to apply new NVMe Clock out setting for MegaRaid 9560 controllers.(DCSG01383812)
-IT Firmware: Increase number of "AllowedFunction" entries in IOUnitPage13 from 20 to a.(DCSG01388196)
Version 23.125.17.00
---------------
BIOS Firmware UEFI Driver
9.45.01.00 23.00.01.00 23.00.01.00
One thing I would like to point that these FW pkg has the SAME FW version
so there will not be any change list.
440-FW
23.125.13.00-DCSG01229202 (FW:23.00.01.00)
23.125.16.00- DCSG01368804(FW:23.00.01.00)
23.125.17.00-DCSG01474661(FW:23.00.01.00)
Version 23.125.16.00
---------------
BIOS Firmware UEFI Driver
9.45.00.00 23.00.01.00 23.00.00.00
Fw don't have any change,so don't have any fixed issue.
Version 23.125.13.00
---------------
BIOS Firmware UEFI Driver
9.45.00.00 23.00.01.00 23.00.00.00
Defects:
-IOC Page 7 does not report the updated "SASNotifyPrimitiveMasks".(DCSG01220829)
-Wrong link speed check while setting host port status gpio.(DCSG01221053)
-HW Workaround:Link between Controller and expander not always recovering after link reset.(DCSG01196230)
-Disable SATA protocol when in optical mode.(DCSG01194126)
-Updated GoldenX to handle the CoreDump Region.(DCSG00042890)
Enhancements:
-[9500] Add support for host phys/lanes in Port Status Green GPIO.(DCSG01207029)
Version 20.125.03.00
---------------
BIOS Firmware UEFI Driver
9.39.00.00 20.00.04.00 20.00.01.00
Defects:
Imbalanced bandwidth performance with 2 x4 expanders connect to Aero IT controller(DCSG00950631
Blue Screens while collecting "pl dbg" logs(DCSG00984451
UBM statistics data collection and UBM error handling fixes(DCSG00975065
Fault 0x070A observed while performing firmware downgrade.(DCSG00758163
Ventura/Mercator: pl: 4311 fault(DCSG00918020
Two elements of SES Page A are assigned same slot number for UBM backplanes with x2 DFC(DCSG00966202
Hot add drive on UBM backplane with x2 or X4 DFC reports incorrect element status in SES Page 02h(DCSG00967012
Response to OOB command is not sent on Internal Dynamic Memory Allocation failure(DCSG00906577
BST: invalid syntax for Uart config(DCSG00957157
[Aero][UBM] Enhance the link configuration to handle the link speeds for SAS/SATA drives behind UBM.(DCSG00552897
Update SSUTimeout Fields Value in BIOS Page 1 to 0xF0(DCSG00982364
Critical Error Log created if the Firmware Download of BIOS using BIOS image from different package than Firmware.(DCSG00951807
Fault 0x7600 observed when 1 phy is disabled in SAS IO Unit page 1(DCSG00788430
Drives not discovered when an enclosure is hot plugged after removing a PCIe switch based JBOF(DCSG00957168
Unsupported MPI Config page read from OOB provides data in response(DCSG00937617
SPDM lib compile error for Ventura build(DCSG00810786
SPDM key reading failed when complete flash Erase case(DCSG01032600
Coverity : Remove dead code(DCSG00982343
VSES : Multiple elements of SES page 0xA are assigned the same slot number(DCSG00973316
pl: NVMe: Format Unit FMTDATA bit should be ignored(DCSG00063448
PL NVMe : IOs fail with SGL length shorter than the transfer legth(DCSG00501518
Performance drop seen with direct attached SAS/SATA drives(DCSG00980873
[BST] Topology information parsing using FW Diag commands is failing(DCSG01045324
pl: backend PCIe: PCIe error handler fails to issue task management with cascading errors(DCSG00839445
FW BST: Larger size IO jobs take more time to start, triggering timeout exception in SAL(DCSG00961165
BST: Fix scripts for SAL stability.(DCSG01012237
Performance drop seen with SAS/SATA drives in Windows using latest driver(DCSG00981706
Update Version Field value in Std Inquiry Data of vSES Device(DCSG00966397
Enclosure handle for some direct attached device might be wrong during Event replay for direct attached slot order case.(DCSG00381441
Data length from host to DA-SEP device not checked if it is more than buffer length in firmware(DCSG00915992
[BST] SEP locate test fails on Atlas attached NVMe drives(DCSG01039953
[Aero][PLDM] PLDM Timer restart failing(DCSG00430198 (Port Of Defect DCSG00830822)
Controller Faults when connected to DA SEP Backplane(DCSG00916381 (Port Of Defect DCSG00918045)
[Aero] Phase 18 build error fix(DCSG00708175 (Port Of Defect DCSG00708188)
Bad PHY events generated by RAID stack for invalid VSES elements slot with Critical status(DCSG00925970 (Port Of Defect DCSG00927932)
FW Fault 2622 observed during system boot up in some new Gen4/Gen5 servers(DCSG00947451 (Port Of Defect DCSG01019237)
HBA hangs on boot with failed UBM backplane in a multi-UBM backplane topology(DCSG00653774 (Port Of Defect DCSG00707457)
Fixed fault 0xF000 when doing VSES task management(DCSG00927996 (Port Of Defect DCSG00934187)
Some drives missing in OS when Direct attached slot order event replay flag is set in NVDATA(DCSG00991409 (Port Of Defect DCSG00996086)
Some drives and enclosures not added to Windows OS when SAS/SATA devices are reduced in NVDATA.(DCSG00654062 (Port Of Defect DCSG00757561)
Fault 0xEE19 observed while running lane break test with managed switch attached to controller.(DCSG00939163 (Port Of Defect DCSG00947866)
(SATA Only) IO Timeouts seen while running Unmap, SATA Passthrough and Read/Write IOs to a SATA drive(DCSG00654439 (Port Of Defect DCSG00831920)
MCTP : MCTP MPI requests are failed with drive missing status even when drive is present(DCSG00952803 (Port Of Defect DCSG00956655)
[Aero][OOB] Firmware download in loop from OOB in PCIe mode fails(DCSG00555977 (Port Of Defect DCSG00831123)
SATA : one or more HDD are not discovered by OS when drives behind expander are powered ON(DCSG00947126 (Port Of Defect DCSG00964427)
pl: SAS IO Unit Page 1 Write Current may not cause phy to be enabled(DCSG00654031 (Port Of Defect DCSG00734511)
EnhancementRequest:
BST: Bring up new Aero activity BST server at BLR(DCSG00323525
BST: Update boardnames in configuration data(DCSG01010542
Connector Order change for 9502-16e controller(DCSG00966344
Create Partial XML for 9502-16e HBA(DCSG00930106
MPI 2.6: Header file changes associated with revision 2.6.11(DCSG00293141
pl: backend PCIe: target link speed diag command(DCSG00757333
Add support for FW UART console to BST scripts(DCSG00776933
Code Coverage improvement for managed switch SES stack(DCSG00949284
SNTL Code coverage Improvement(DCSG00949306
BST: Add custom Cardnames to BST UART configuration(DCSG00985842
Code Coverage improvement for managed switch MPI device stack(DCSG00949285
Release Automation: Check for failure during baseline creation(DCSG00958012
[BST] Graceful handling of controller reset scenario(DCSG01027037
SAS phy port configuration of UBM connected phys based on UBM DFC Link width.(DCSG00927212
[OEM][BST] Add a new OEM server to BST(DCSG00776916
PL SATL : Add SAT translation for the Concurrent Positioning Ranges VPD page(DCSG00927210
PL SATL : Update the WRITE SAME command to account for Zoned Block Devices(DCSG00500552
Remove SASPARSER binary from Release Order(DCSG00957868
Release Automation: automate rebase operation for phase specific streams(DCSG00950531
UBM error handling improvements and debug statistics data collection(DCSG00903198
Add cable breaker support to BLR test Hosts(DCSG00777063
BST: Replace Python's telnet lib APIs with invocations of native telnet client(DCSG01008755
Integrate MPI 2.6.11 headers(DCSG00408836
cable breaker exception handling and support for array controller(DCSG00086796
SATL : ATA Passthruough command handling when Datalength in MPI < data requested to drive(DCSG00833193
BST: Update Enclosure Logical ID for BST setups(DCSG01015576
[BST] Add SEP related test cases(DCSG00949307
[Aero][BST] Improve the code coverage of file plPciDeviceManager.c(DCSG00947724
Update SAS 3.5 FW summary release notes(DCSG00979878
[Aero][BST] Improve the code coverage by adding new test cases(DCSG00948894
CFGI: Integrate MPI 2.6.11 headers with CFGI Lib.(DCSG00481628
Update 9500-16i, 8i channel XMLs to support new VPP backplane management device address.(DCSG00351950
BST: Add locate PD test cases to UBM BST(DCSG00019759
PL SATA : Read logpage 12 and 13 during SATA initialization to get features supported for NCQ encapsulation using FIS porting(DCSG00779724
PL : Remove obsolete workarounds(DCSG00008204
BST: On IO errors, retry IO after some delay(DCSG01029567
Enable collection of PCIe Link event "RECEIVED_NAK_DLLP" (EventCode=0x08) by default(DCSG00122084
SPDM feature compile out from FW code(DCSG00707071
[Aero] Enable UBM detection logic on all connectors for OEM HBA with SEP_PRESENT GPIOs(DCSG00927207
Release Automation: Assign release type when creating ROP(DCSG00941419
Support streaming of debug logs (HTB) via I2C OOB band on Ventura/Aero IOC/HBA (Part B)(DCSG00927213
[BST]Add support to execute scripts for one specific card(DCSG00961877
[UBM] Add detection of SAS/SATA drive with UBM backplane supporting IFDET2# and PRSNT#(DCSG00945423
Blackduck: Remove non UTF-8 encoding characters from source files(DCSG00258258
Add 9502-16e board Nvdata to Aero ROP(DCSG00966467
Code Coverage improvement for NVMe SGL analysis and translation stack(DCSG00949287
Support downloading of the Host-based Trace Buffer (HTB) via MCTP OOB Interface on Ventura/Aero IOC/HBA (Part A)(DCSG00500554
BST: When comparing slot numbers, ignore the strings from eminfo command output(DCSG01007045
BST CodeCoverage : Add BST test case to improve MPI task management code coverage(DCSG00999219
[Aero][PLDM] Platform changes to accommodate latest PLDM baseline(DCSG00447989 (Port Of EnhancementRequest DCSG00500775)
SEKM Support for IT controllers(DCSG00433132 (Port Of EnhancementRequest DCSG00777312)
SEKM: Prevent firmware Download of firmware that do not support SEKM when SEKM is enabled.(DCSG00549524 (Port Of EnhancementRequest DCSG00816022)
Error handling of UBM CHANGE_DETECT# signal(DCSG00962565 (Port Of EnhancementRequest DCSG00963253)
[SPDM] Blocking slots 1-7 from configuring SPDM certificates(DCSG00500296 (Port Of EnhancementRequest DCSG00507210)
Reintroduces the previous security page as MR_MPI26_CONFIG_PAGE_SECURITY_1 to align with current NVDATA(DCSG00977495 (Port Of EnhancementRequest DCSG00977500)
SEKM feature enhancements to handle error scenarios(DCSG00777328 (Port Of EnhancementRequest DCSG00903186)
Enhance Error scenario handling in SEKM Feature code(DCSG00966411 (Port Of EnhancementRequest DCSG00974796)
Version 18.125.06.00
---------------
BIOS Firmware UEFI Driver
9.35.00.00 18.00.03.00 18.09.01.00
Fix issue:
-Disk cannot be detected after the driver of CFF 440-16i is loaded during installation Windows 2022
Version 18.125.04.00
---------------
BIOS Firmware UEFI Driver
9.35.00.00 18.00.02.00 18.09.01.00
Fix issue:
System hung at DXE INIT side
Version 18.125.03.00
---------------
BIOS Firmware UEFI Driver
9.35.00.00 18.00.02.00 18.09.01.00
Ph_18
Defects:
-PL SATA Only : SATA PFA drive is not recognized as PFA drive in Aero while hot-plugging.(DCSG00427743
-Some drives and enclosures not added to Windows OS when SAS/SATA devices are reduced in NVDATA..(DCSG00654062
-Ring buffer decoder GUI hangs if timestamp is invalid.(DCSG00437238
-[NVMe] Firmware download in mode E failed with error Invalid Firmware Image.(DCSG00313245
-[Code Review] Updated CoreDump related data structures to have capitalized first letter for the member fields.(DCSG00250948
-pl: NVMe: chain to PRP SGL for non-read/write IO may be handled improperly.(DCSG00408313
-[NVMe] Send diagnostic to abort background test completes with success when no background test started..(DCSG00310330
-[NVMe] Inquiry command to NVMe device reporting old rev firmware after drive firmware update completed successfully.(DCSG00321504
-SPDM IT:SPDM BMC bring up on P2 server.(DCSG00238540
-SPI LIB 1 - Manual Flash writes to flash parts connected to chip selects other than 0 fail..(DCSG00350016
-Aero: PL with newer Atlas FW (4.2) has extra slot number in the Atlas enclosure.(DCSG00284238
-Format Repair operation fails on certain NVMe drive.(DCSG00408635
-Ventura/Mercator: pl: direct attached SAS or SATA device may not be discovered.(DCSG00408109
-SPILIB: NVSRAM uses old ASENB command.(DCSG00342936
-[NVMe] Protect bit is always set in standard inquiry data for NVMe drives..(DCSG00301661
-README file mentions sas2parser instead of sasparser.(DCSG00394150
-PL SNTL : Accumulated Power On Hours value reported by LogSense translation is byteswapped.(DCSG00499729
-[NVMe] SCSI TUR command fails when sent to a NVMe drive with corrupted LBA 0.(DCSG00299624
-[Ventura] Some NVMe drives are not discovered.(DCSG00301612
-SPILIB: FIx definition of SPI_LIB_TYPE for SPILIB1.(DCSG00354885
-SPILIB2: Some properties functions access the wrong array.(DCSG00340954
-[NVMe] Send diagnostic with self test bit 1 but selftestcode non 0 is not failed..(DCSG00306498
-Move Version control files to folder for Release BST.(DCSG00342866
-[NVMe] Mode Select command to write Read Write Error recovery page fails..(DCSG00307175
-[VSes] Connector name of the VSes device in SAS device page 0 has invalid data if no device is connected to port 0.(DCSG00383998
-[Aero] Phase 18 build error fix.(DCSG00708175
-BST: ScrutinyCli invoked with invalid options.(DCSG00428615
-Fixed PH17 Coverity issues.(DCSG00335212
-[NVMe] PL Fault 0xE429 is seen while performing reset for certain NVMe drive..(DCSG00395750
-pl: NVMe: status code type not checked upon Write Buffer callback.(DCSG00419779
-Coverity found defects for converting an expression to a narrower type in SATL code..(DCSG00297461
-[Ventura][NVMe] Phy disable from application does not removed the drive from PL..(DCSG00384856
-PL fault: Invalid Msg Frame fault triggered on external card connected to UBM BP.(DCSG00408493
-Uninitialized pointer access in UBM code..(DCSG00446918
-[VSes] SCSI State not correctly set for some error response to SCSI commands..(DCSG00312554
-[NVMe] Extended Self Test Completion time in Control mode page is byte swapped.(DCSG00308453
-Trigger script with PassComponentTable Command set to invalid Value led to rolling PLDM error messages.(DCSG00500454
-pl: NVMe: async event handler proceeds during IO quiescing.(DCSG00431716
-Fix coverity reported defects.(DCSG00282926
-[NVMe] Parameter Code in Self Test Results log page is incorrect..(DCSG00422250
-Element Status code of a Slot in SGPIO BP with no drive marked as 'Unknown'.(DCSG00428815
-AXI access errors causing FW asserts or faults due to invalid SATA passthrough commands.(DCSG00215338
-pl: SAS IO Unit Page 1 Write Current may not cause phy to be enabled.(DCSG00654031
-[NVMe] TSD bit not getting set in Reference Temperature log parameter.(DCSG00430063
-MBEDTLSLIB: Compile out Mbed TLS Self-Test code.(DCSG00335755
-Update SBLIB version in BST version file.(DCSG00316342
-Update the Driver Trigger Page data structs' size and add padding to make them 256 bytes.(DCSG00258095
-Performance drop of 5-9% seen with Random Read/Write IOs to NVMe drives..(DCSG00258412
-SPILIB2: Small misaligned transfers sometimes result in a read-back verify failure on page writes.(DCSG00283387
-[SPDM IT] Return actual size of certificate chain content to SPDM LIB.(DCSG00233805
-pl: backend PCIe: fix a couple of issues related to PCIe discovery and NVMe init.(DCSG00355408
-NVMe Repair Operation hangs on a certain NVMe drive with Multiple Namespace.(DCSG00415462
-Fix Coverity issues.(DCSG00293500
-Release Automation: If release job web page takes more than 60 secs to load, script throws exception.(DCSG00297363
-MAC verification failed due to inconsistent secure ID.(DCSG00309854
-pl: Incorrect c0 values displayed for SAS/SATA in the "pl serdes tx" output.(DCSG00422289
-NVMe : PROTECT bit in inquiry data is set..(DCSG00308451
-Aero: HW Workaround - When Aero is in the L1 state it periodically (every 2 ms) transitions to L0 and back to L1.(DCSG00501537
-VSES getting removed in OS on controller reset..(DCSG00301631
-[Aero] SAS SATA only partial nvdata xml are not included in release order..(DCSG00394146
-[NVMe] Mode select command to set Control Mode page with last two bytes changed completes successfully..(DCSG00315331
-SPDM Authentication fails when BMC re-triggers SPDM Handshake.(DCSG00547436
-PL Backend PCIe : SATA drive discovery is delayed.(DCSG00310045
-SPDMIT: Return appropriate error to SPDM Lib when read certificate from security page 0 fails.(DCSG00299079
-[NVMe] The long LBA bit is not set in Mode Parameter header..(DCSG00319580
-Coverity issue.(DCSG00293875
-PL Fault 0xEA11 observed, while upgrading Atlas FW using StorCLI in presence of bad NVMe PD's present in the Atlas..(DCSG00324838 (Port Of Defect DCSG00340935)
-[Aero] Controller missing in System Bios..(DCSG00411545 (Port Of Defect DCSG00420098)
-SATA Only: Command timeout observerd on SATA drives.(DCSG00344039 (Port Of Defect DCSG00356008)
-Ventura/Mercator: pl: 4311 fault.(DCSG00918020 (Port Of Defect DCSG00929451)
-Out of bound memory access when assigning dma group for controller devices..(DCSG00243152 (Port Of Defect DCSG00243641)
-Observed PL Fault 6231 while running IOs along with Expander phy link reset..(DCSG00363807 (Port Of Defect DCSG00373461)
-Device add/remove event sent with wrong enclosure handle in certain multi VSes topology..(DCSG00350248 (Port Of Defect DCSG00380548)
-EID is not assigning back with IT controller restart.(DCSG00394045 (Port Of Defect DCSG00397565)
-PL NVMe : PCI task management is not getting completed..(DCSG00231422 (Port Of Defect DCSG00266053)
-During OS reboot some drives go missing..(DCSG00354770 (Port Of Defect DCSG00361759)
-System bios hangs during initial drive discovery..(DCSG00312551 (Port Of Defect DCSG00382416)
-HII Refresh Topology Hangs when connected to Faulty SES Device.(DCSG00385938 (Port Of Defect DCSG00404446)
-Enclosure ID of some Switch attached NVMe devices missing after system reboot..(DCSG00414735 (Port Of Defect DCSG00426692)
-(SATA Only) IO Timeouts seen while running Unmap, SATA Passthrough and Read/Write IOs to a SATA drive.(DCSG00654439 (Port Of Defect DCSG00906897)
-[SATA Only] SCSI Start Stop Unit command with power condition active fails..(DCSG00349970 (Port Of Defect DCSG00353138)
-0x6001 Fault running TMs with certain NVMe translated Host IOs.(DCSG00362831 (Port Of Defect DCSG00385767)
-Drives connected behind external card with VSES disabled, failed to detect in Linux OS.(DCSG00350402 (Port Of Defect DCSG00363785)
-Firmware fails to send Enclosure removal event to host when the enclosure is removed from the topology..(DCSG00232962 (Port Of Defect DCSG00244617)
-[Aero/Ventura] Bootloader corruption with firmware download and DC cycle in loop..(DCSG00238233 (Port Of Defect DCSG00245454)
-ParentDevHandle value calculated for given Phy Number is incorrect for Direct Attached Devices in Event Replay logic.(DCSG00299632 (Port Of Defect DCSG00299823)
-Controller Faults when connected to DA SEP Backplane.(DCSG00916381 (Port Of Defect DCSG00918083)
-[SATA ATAPI] FW fault 0x6231 seen while completing some IO for ATAPI device..(DCSG00350047 (Port Of Defect DCSG00353918)
-[Aero][UBM] Enhance the link configuration to handle the link speeds for SAS/SATA drives behind UBM..(DCSG00552897 (Port Of Defect DCSG00706402)
-PL : Missing drives during AC power cycle test.(DCSG00275868 (Port Of Defect DCSG00301823)
-ExtManPage41 TX Values are not being applied / run by AERO SERDES.(DCSG00311524 (Port Of Defect DCSG00311739)
-0x6001 Fault while running driver load/unload with simultaneous NVMe drive pulls.(DCSG00378243 (Port Of Defect DCSG00385686)
-PL: 9460-16i incorrect slot numbers assigned attaching to OEM specific mixed mode backplane.(DCSG00243953 (Port Of Defect DCSG00342787)
-[Aero][PLDM] PLDM FW discovery results in 265D Fault.(DCSG00307769 (Port Of Defect DCSG00330183)
-Ventura: Faults 0x0101 and 0x5805 Invalid LMID Index Seen after hundreds of cold boots.(DCSG00338118 (Port Of Defect DCSG00384000)
-Serdes TX table in pl diag dump has the Pre-cursor, Post-cursor and Attenuation values mixed.(DCSG00388268 (Port Of Defect DCSG00404448)
-NVMe Init error drives are not discovered after pull/push within DMD timeout.(DCSG00242197 (Port Of Defect DCSG00250023)
-ventura build issue with PL PCI DEVICE feature disabled.(DCSG00286358 (Port Of Defect DCSG00286361)
-SATA only: WRITE SAME NCQ encapsulation assumes NonData NCQ is supported if Zero EXT is Supported.(DCSG00398894 (Port Of Defect DCSG00412030)
-Update the SPDM print index properly before adding the prints to ring buffer.(DCSG00335886 (Port Of Defect DCSG00337717)
-[NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive.(DCSG00136092 (Port Of Defect DCSG00237479)
-LED Blink/Unblink operation fails on certain Slots in UBM using MPI SEP Request.(DCSG00282826 (Port Of Defect DCSG00290200)
-PL NVMe : PCI task management is not getting completed..(DCSG00231422 (Port Of Defect DCSG00245537)
-[Aero][OOB] Firmware download in loop from OOB in PCIe mode fails.(DCSG00555977 (Port Of Defect DCSG00908352)
-Ventura: SAS3616W or SAS3616W based boards have links less than epected width.(DCSG00249594 (Port Of Defect DCSG00249753)
-[Aero][PLDM] PLDM Timer restart failing.(DCSG00430198 (Port Of Defect DCSG00960384)
-Remove LogSpecific member in the structure 'IOPI_LOG_DETAIL.(DCSG00318366 (Port Of Defect DCSG00318943)
-PL SATA Only : Controller hang observed for ATA Passthrough command with count value set to 0.(DCSG00250952 (Port Of Defect DCSG00266833)
-PL fault 0xE40E observed accessing unconfigured MPI backend device registers through CLI cmd.(DCSG00234837 (Port Of Defect DCSG00238649)
-9500-16e disappears on system reboot.(DCSG00367091 (Port Of Defect DCSG00414022)
-HBA hangs on boot with failed UBM backplane in a multi-UBM backplane topology.(DCSG00653774 (Port Of Defect DCSG00707464)
-OEM UBM backplane Slot status LED Blinks only for 10 secs for NVMe VDs with Toggle Host LED management.(DCSG00323361 (Port Of Defect DCSG00380726)
-Controller fault observed on changing some phys to manual port config with port set to 0..(DCSG00237498 (Port Of Defect DCSG00245531)
-Aero A0: Controller faults 0xD015 with Refresh topology from BIOS in a managed PCIe switch config..(DCSG00414714 (Port Of Defect DCSG00418238)
-[Aero][PLDM] Date format exposed by IT to PLDM library is not as per PLDM spec.(DCSG00363642 (Port Of Defect DCSG00398739)
-9500-16e fails to recover after warm boot.(DCSG00422618 (Port Of Defect DCSG00422813)
-PL: Reply to IO's bad SGL to Atlas SES has wrong DevH and SMID's incorrectly tries to fit 3 SGEs inframe.(DCSG00315476 (Port Of Defect DCSG00366033)
-[VSes] Element status set to 'Unknown' in SES page 2 of VSES for some phys where nothing is connected..(DCSG00333163 (Port Of Defect DCSG00343848)
-Make Clear of the PEPP version of ConfigValid Applicable to IT Boot Code Only.(DCSG00398453 (Port Of Defect DCSG00404468)
-As part of the Device Add\Removal Event, the enclosure handle passed on by the PL FW to the upper layer is incorrect..(DCSG00298128 (Port Of Defect DCSG00299826)
-When performed export csr for all 8 slots in batch observing for few slot command is success and for other it is failure..(DCSG00421812 (Port Of Defect DCSG00425171)
-NVMe Init Error: Device with no namespaces shows 'Namespace count Invalid' as Unrecoverable Error.(DCSG00290593 (Port Of Defect DCSG00303510)
-pl: backend PCIe: limit CRS retry count.(DCSG00312206 (Port Of Defect DCSG00324774)
-[VSes] Slot status is reported as 'Unsupported' for drives connected to UBM backplane..(DCSG00337912 (Port Of Defect DCSG00353069)
-PL NVMe : IOs fail with SGL length shorter than the transfer legth.(DCSG00501518 (Port Of Defect DCSG00735325)
EnhancementRequest:
-SPILIB2: Add support for AV1 ring buffers EnhancementRequest ID: DCSG00421632
-OEM Smart Carrier Backplane code cleanup EnhancementRequest ID: DCSG00171467
-Add new field DEPOPULATION TIME as part of translation of VPD Page - Block Device Characteristics. EnhancementRequest ID: DCSG00167925
-SPILIB1: CLear LC bits in Spansion, wait longer for NVSRAM EnhancementRequest ID: DCSG00427348
-SPDM IT: Add memory allocation/free for SPDM_LIB EnhancementRequest ID: DCSG00229260
-SPILIB2: Integrate 20.00.11.00 with the IT firmware tip EnhancementRequest ID: DCSG00297796
-pl: backend PCIe: runtime control for lane margining debug console prints EnhancementRequest ID: DCSG00373313
-SPILIB2: Add spi2FlashWriteDataNoVerify() API EnhancementRequest ID: DCSG00394830
-pl: NVMe: update to latest SNTL specification Phase 2 EnhancementRequest ID: DCSG00340625
-[NVMe] SCSI Send Diagnostic command translation for NVMe. EnhancementRequest ID: DCSG00261270
-Enhancement to source of randomness for generating key pair EnhancementRequest ID: DCSG00208477
-MBEDTLS LIB: Add license files to source tree EnhancementRequest ID: DCSG00813882
-Add dumps to pl dbg EnhancementRequest ID: DCSG00008206
-pl: backend PCIe: CRS retry limit disable bit EnhancementRequest ID: DCSG00325823
-Update SAS 3.5 FW summary release notes EnhancementRequest ID: DCSG00384316
-SPILIB2: Add support for FLASH suspend/resume. EnhancementRequest ID: DCSG00371513
-VSES: Removed loginfo code when the command is failed with a check-condition EnhancementRequest ID: DCSG00235941
-SPILIB2: AV2 Core Support [PA 0.2] EnhancementRequest ID: DCSG00230517
-Update the event logging when the "CoreDump" region is erased from ScrutinyCLI command EnhancementRequest ID: DCSG00367325
-Summary of changes EnhancementRequest ID: DCSG00383538
-[IT SPDM] Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust EnhancementRequest ID: DCSG00218564
-SPILIB: Add support for multiple erase sizes in uniform flash parts EnhancementRequest ID: DCSG00309579
-[IT SPDM] Implement client APIs for SPDM Get Measurement command. EnhancementRequest ID: DCSG00256411
-Add version control file to build EnhancementRequest ID: DCSG00242260
-Ventura/Aero: Request by MegaRAID to output debug data in vtboot.rom for future debug EnhancementRequest ID: DCSG00420316
-VSES - UBM DFC Array Device Element status read optimizations EnhancementRequest ID: DCSG00347743
-[NVMe] Provide interface to reset NVMe drive after shutdown. EnhancementRequest ID: DCSG00109904
-NVMe Sanitize Translation EnhancementRequest ID: DCSG00266054
-[NVMe] Update SCSI to NVMe translations based on latest SNTL document. EnhancementRequest ID: DCSG00235935
-SPI LIB 1- Enable Suspend-Resume support for Winbond and ISSI flash parts. EnhancementRequest ID: DCSG00380266
-Update the IT/PL Firmware Error codes guide EnhancementRequest ID: DCSG00349980
-Security Key page MPI definitions should more descriptive EnhancementRequest ID: DCSG00336313
-SPILIB2: Add Avenger2 Duty Cycle and Sample Delay options EnhancementRequest ID: DCSG00287035
-Enable 24 NVME drive support for internal and external controllers EnhancementRequest ID: DCSG00306646
-SPILIB: Add 1_4_4 read/write and NVSRAM commands to analyzer decoder EnhancementRequest ID: DCSG00358690
-SPLIB2: Eliminate debug prints from NVSRAM init EnhancementRequest ID: DCSG00299483
-SPILIB 2.0 : expander/Atlas Modify time loops to handle multi-processsing better EnhancementRequest ID: DCSG00220784
-[Ventura/Aero] Block the OOB FW download when firmware update is in progress. EnhancementRequest ID: DCSG00249958
-SPILIB2: Add support for 100 MHz using default configuration for Macronix 256 MBit EnhancementRequest ID: DCSG00409337
-Host Trace Buffer Triggers to be persistent EnhancementRequest ID: DCSG00235945
-Added IOCParam to IOUnit Control command to allow periodic time-sync EnhancementRequest ID: DCSG00235948
-[SPDM IT] Export CSR & Import Cert Open & Close Session EnhancementRequest ID: DCSG00221406
-SPILIB2: Add code to clear block protect bits if they are set EnhancementRequest ID: DCSG00420314
-SPILIB 2.0: Avenger2 and R processor build support EnhancementRequest ID: DCSG00230514
-Release Automation: Add support for generating Ventura ROP EnhancementRequest ID: DCSG00246102
-Aero Secure Boot: Add Key Update Pending Check for 'COMPLETE' Image Download EnhancementRequest ID: DCSG00241566
-[Aero/Ventura]Fix Coverty issues in Phase_18 TIP EnhancementRequest ID: DCSG00507240
-Support for Mode 5 NVMe drive firmware download with Chain SGL SCSI Write buffer request. EnhancementRequest ID: DCSG00171452
-Total vSES Enclosure Slot Count value reported is incorrect in host tools\MR FW with NVMe drive which fails initialization EnhancementRequest ID: DCSG00546745
-[NVMe] Prevent non Read/Write SCSI IO Timeouts while running heavy greater than MDTS RW IOs EnhancementRequest ID: DCSG00234748
-NVMe Init Failure Reporting & Recovery of NVMe Drive with Partial Capacity NSID 1 Namespace EnhancementRequest ID: DCSG00310384
-SPDMLIB: Support SPDM Challenge command request for hash of all supported measurements EnhancementRequest ID: DCSG00366048
-Vent/Aero: Integrate SPILIB 20.00.14.00 EnhancementRequest ID: DCSG00317165
-Log 0 SPDM events for certificate slot & key management EnhancementRequest ID: DCSG00322202 (Port Of EnhancementRequest DCSG00366811)
-[Aero][PLDM] Platform changes to accommodate latest PLDM baseline EnhancementRequest ID: DCSG00447989 (Port Of EnhancementRequest DCSG00960360)
-VSES: Update diag page 02h status reporting for Array device elements to use UBM DFC SnC Desc Element status code EnhancementRequest ID: DCSG00308393 (Port Of EnhancementRequest DCSG00379789)
-[SPDM] Blocking slots 1-7 from configuring SPDM certificates EnhancementRequest ID: DCSG00500296 (Port Of EnhancementRequest DCSG00645950)
Version 16.125.15.00
---------------
BIOS Firmware UEFI Driver
9.31.00.00 16.00.12.00 16.00.08.00
Ph_16.0
Defects:
-PLDM single firmware update logs multiple debug messages in controller trace buffer.(PLDM single firmware update logs multiple debug messages in controller trace buffer)
-PLDM Type 2 - Change debug print filter level to "Warning" for PollForPlatformEventMessage command.(DCSG00263767)
-Fix Coverity tool reported defects.(DCSG00266270)
-fixed the parameter difference for the PLDM Type 5 print framework..(DCSG00286651)
-pldmFreeFwUpdtResources() doesn't frees RetryRqstTimer correctly.(DCSG00313887)
-Issue in freeing PLDM firmware update resources.(DCSG00317911)
-Assertion failure in fw\cpu\arm\exceptions.c at line 1006 on triggering QueryDeviceIdentifier command in Download State.(DCSG00337907)
-Coverity defects fix..(DCSG00340836)
-PLDM Type 2 - Fail module initialization if Managed Device invokes initialization API without allocating memory.(DCSG00360498)
-OOB-MCTP over I2C - FW updates in Loop hits PLDM Fault 0x6.(DCSG00380088)
-PLDM - Fix compilation errors reported in an OEM platform.(DCSG00382501)
-Doxygen build error.(DCSG00415793)
-[Aero][PLDM] PLDM Timer restart failing.(DCSG00430198)
-Updated GoldenX to handle the CoreDump Region.(DCSG00042890)
Enhancements:
-Implemented linked list for entity and sensors.(DCSG00219964)
-Add snapdump support for PLDM Type 2 and Type 6 modules.(DCSG00226303)
-PLDM Type 2: Implement API changes and support for Redfish message event in PLDM Monitoring and Control module.(DCSG00253011)
-PLDM Type 6 - Add support for Redfish Message Event.(DCSG00255563)
-PLDM Monitoring and Control: Addressed the Coverity reported issues and added abort function.(DCSG00342504)
-Address Coverity tool reported issues in PLDM Type 2 and Type 6 modules.(DCSG00352028)
-Enhance PLDM library for separation of APIs/LIB and source code.(DCSG00394996)
-Code cleanup activity.(DCSG00395207)
-PLDM - Handle a TODO related to sensor re-arm unavailable in present state and update copyright year in all Type 2 files.(DCSG00404477)
-[Aero][PLDM] Platform changes to accommodate latest PLDM baseline.(DCSG00447989)
-For report LUN command, Increase retry count from 3 to 5 and add SCSI status BUSY into retry loop.(DCSG00930134)
Version 16.125.12.00
---------------
BIOS Firmware UEFI Driver
9.31.00.00 16.00.12.00 16.00.06.00
Ph_16.0
Defects:
-Response of TransferComplete (0x16) become irrelevant if it is received after the successful completion of CancelUpdateComponent(0x1C)and needs to be dropped.(CSG00033524)
-SPDMLIB: Add change to SConstruct to copy library output file (*.a) to release folder(CSG00117832)
-CFGI : The first 32 characters of MPI defines should be unique(CSG00086291)
-SPDM_LIB: Add alignment parameter into SPDMLib_Calloc interface(CSG00237674)
-PLDM Type 6: Incorrect error code returned for resource unregistration(CSG00067924)
-NVMe Init reports wrong failure error codes(CSG00103993)
-Coverity Bugs in PL Enclosure Management Files(CSG00043514)
-PL: MS-SES with no Array Devices in Atlas SES causes 0x7200 fault(CSG00077263)
-Additional Key Data field of Security Page 1 is missed in XSD definition(CSG00077979)
-BST: BST cancellations on cable breaker comm port unavailability(CSG00212793)
-Unitialized pointer was being accessed(CSG00096545)
-MBEDTLS LIB: fix compilation error during IT FW build(CSG00234920)
-SPDM LIB: Set ECDSA signature with correct size in Signature field of SPDM Challenge response buffer before sending to BMC server(CSG00225192)
-PLDM Type6 : Change filename for fixing doxygen compilation(CSG00081863)
-PLDM Type5 : Controller FW Downgrade through BMC results in controller FW crash(CSG00095783)
-SPDM: Attestation failed with wrong Nonce values(CSG00126872)
-CFGI : MPB2 read fails with invalid checksum(CSG00098544)
-PLDM: Pass Timer-id that needs to be restarted to Pldm-timer-restart operation.(CSG00018645)
-Change file name of SpdmDebug.h to SpdmDebugs.h . And Check in SpdmDebugs.h for IT(CSG00074556)
-PL: Aero -- Atlas US Cable Pull/Push Results in Missing Enclosure Slot Info(CSG00181448)
-Coverity found defect in MPI Device and FPE modules.(CSG00098787)
-NVME Drives not getting discovered on inserting in Customer UBM3 x4 backplanes until OCR.(CSG00081732)
-[Aero][PLDM] Date format exposed by IT to PLDM library is not as per PLDM spec(CSG00363642)
-BST: version.mak no longer a part of BST verification(CSG00368158)
-Correct Sblib Int make sure ER 110403 and ER 166877 are present (2)(CSG00215388)
-BST: UBM BST funtonality is broken on latest BST code.(CSG00216461)
-Observed Data Corruption during IO stress test.(CSG00212797)
-PLDM Type-2 : GetPDRRepository command fails with large configuration (mulitple drives and volumes)(CSG00097462)
-Addressing IT raise defects in SPDM library change.(CSG00061718)
-MBEDTLS LIB: Fix dynamic memory release bug in Mbed Tls Library(CSG00216944)
-Aero A0: Fault D033 running IO + Expander Phy Link/Hard Resets to Expander phys(CSG00045450)
-BST: Case mismatch in card name(CSG00114314)
-Phase 15 Coverity Bug Fixes(CSG00104982)
-Large topology of more than 500 drives cannot be supported on SAS 3.5 Channel Controllers(CSG00108246)
-Mismatch between subsystem id in NVDATA and SBR for 9405-W 16i(CSG00077700)
-BST: Num Slots config file update for topology with Atlas Configuration(CSG00312633)
-Release Automation: Exceptions during execution of release script(CSG00151389)
-Aero A0: External cards do not support more than one PCIe drives.(CSG00249770)
-Do not process any response msg if FD is in PLDM_FW_UPDT_IDLE state.(CSG00024158)
-[SPDM] SPDM lib changed one of header file name , seeing compilation error in IT.(CSG00077919)
-IT SPDM commands not working via host interface(CSG00134673)
-PCIe Switch Page 250 has NumPorts set to zero, and this page is not included in "iop show cfg all"(CSG00101756)
-MBEDTLS LIB: Add change to SConstruct to copy library output file (*.a) to release folder(CSG00117834)
-Coverity Defects in SATA and VPP code.(CSG00234415)
-MFG Page 49/50/51 defines are not compiled(CSG00083748)
-MBEDTLS Lib: Alignment issues while certificate verification on IT cards(CSG00312818)
-Aero: PswSbr.bin file is read only and causes an error when running the RMC script(CSG00082963)
-SPDM_LIB: Set tagOwner as per SPDM request.(CSG00239464)
-BST: Fix the compilation error for UBM BST(CSG00062522)
-PL: SMP Timeouts During Expander Phy Reset Test(CSG00043616)
-[Aero] SATA drive gets dropped when corresponding phy is disabled and enabled.(CSG00222544)
-PL: Adjust the MPI Device support check to only support Atlas's MPI Device(CSG00040939)
-Updating FW (on 9400 series HBA) from Ph-7 to Ph-14 causes "invalid flash" message on FW bootup(CSG00167100)
-Fail to read Extended Expander Page 250(CSG00092804)
-BST: SAL reports unknown device type for drives(CSG00239268)
-pl: NVMe: 265D fault in out of resource case(CSG00093410)
-Phase 15 Coverity Bug Fixes(CSG00105045)
-[BST] Remove the erase persistent test case from BST.(CSG00305439)
-(MS SES) Non data transfer SCSI IO failed with Invalid SGL error(CSG00234926)
-Duplicate MPI Toolbox Tool Values in MPI temp(CSG00086898)
-NVMe device not discovered after disable-enable PCIe link in PCIe IO Unit page 1(CSG00082524)
-BST: ELID update due to SAS-Address update on Blr Servers(CSG00301666)
-BST: POR Reboot requires a further check(CSG00086783)
-Controller fault 0x1902 is seen while issuing locate command to NVMe drives(CSG00062252)
-PLDM RDE - MultipartReceive command fails with error INVALID_DATA for non-zero OperationID(CSG00165437)
-Fixing Coverity issues(CSG00096489)
-SBLIB: Getting Inconsistent secure ID on IT cards(CSG00309847)
-BST: Aero with Atlas switch Num slot update(CSG00284255)
-Skip completeflash images during BST(CSG00337918)
-"Add enclosure event for an enclosure that is already active" error message observed in Windows event logs(CSG00063929)
-SPDM LIB: Need to include header file SpdmLibTypes.h in SpdmLibIFace.h(CSG00074328)
-Build error in PLDM Library on ARM 4.1 compiler (done with Atlas FW code)(CSG00019014)
-PLDM Lib: Unable to stop timer (PLDM Fault 0x11)(CSG00134602)
-iop show cfgspace doesn't work(CSG00066110)
-During OS reboot some drives go missing.(CSG00354770)
-Remove LogSpecific member in the structure 'IOPI_LOG_DETAIL(CSG00318366)
-PLDM Type5 : Upgrade to the latest signed FW fails(CSG00076949)
-Bug Fix In get CERT and While reading the certificate from the client(CSG00047643)
-ED91 Fault while running IOs + OCR (controller reset) testing(CSG00057254)
-Coverity Defects(CSG00094727)
-The first 32 characters of MPI defines should be unique(CSG00086266)
-PH15 Scrutiny CLI: device c command output is not giving the details of the all the devices connected to the expander(CSG00102332)
-print correct variable during error condition(CSG00096538)
-pl: backend PCIe: prevent switch rediscovery quirks(CSG00018730)
-Incorrect slot count is present in config, for a BP connected to external card in BST server.(CSG00319578)
-Firmware fails to send Enclosure removal event to host when the enclosure is removed from the topology.(CSG00232962)
-EID is not assigning back with IT controller restart(CSG00394045)
-Coverity defect fix(CSG00231928)
-BST: Board naame format error(CSG00143769)
-[Aero] Application scanning for I2C devices on I2C bus hang when OOB configured to MCTP-PCIe mode(CSG00103208)
-NVMe Init error drives are not discovered after pull/push within DMD timeout(CSG00242197)
-9500-16e disappears on system reboot(CSG00367091)
-PLDM Type 6: BEJ buffer insertion pointer is not incremented when an element is added to array context(CSG00067926)
-BST: NumSlots fix for Ph14 &15 broke BST on other fw phases(CSG00315471)
-Sea 16e PCIe TX Compliance Test Failure(CSG00052179)
-Duplicate slot IDs assigned for SAS/SATA drives on elrond Ex1 backplane when it is connected to 9405W 16i controller.(CSG00072826)
-Ventura/Mercator: pl: 4311 fault following SAS IO Unit Page 1 write(CSG00099275)
-PL Backend PCIe: 0xEE1A fault observed with bad clocked Aero and Atlas(CSG00080298)
-RDE: Valid schema class can't be more than 4 for 'GetSchemaURI' command(CSG00109749)
-Coverity found defect in SATA and Enclosure management modules.(CSG00098596)
-Controller fault observed on changing some phys to manual port config with port set to 0.(CSG00237498)
-Ventura: SAS3616W or SAS3616W based boards have links less than epected width(CSG00249594)
-Make Challenge Buffer Include Get_Digest/Digest, Get_Cert/Cert(CSG00055393)
-9500-16e fails to recover after warm boot(CSG00422618)
-Correct Sblib Int make sure ER 110403 and ER 166877 are present(CSG00214265)
-BST: Uart Utility re-visit(CSG00113761)
-pl: backend PCIe: resource leakage during direct attached event generation(CSG00093660)
-[Aero][PLDM] PLDM FW discovery results in 265D Fault(CSG00307769)
-Disable CoreDump when Flash device is not present(CSG00054500)
-BST: Case mismatch for custom card name(CSG00115303)
-SBLIB: Significantly longer boot times that previously encountered in MR CBB(CSG00299427)
-Build failed after MbedTLS new base line pulled(CSG00074952)
-pl: port enable is delayed when SAS/SATA devices are attached to a UBM backplane(CSG00076783)
-BST: Encl_logical_id update(CSG00298990(
-Observed PL Fault 0xEE17 when NVME drives connected via PCIe switch.(CSG00108281)
-[MBEDTLS] Device Key Pair Generation resulting in different Keys on IT card(CSG00318909)
-Increase the time wait time when quad mode bit gets written for write operation to complete.(CSG00061711)
-Out of bound memory access when assigning dma group for controller devices.(CSG00243152)
-SPILIB 2.0: Cypress 256Mbit SPI Flash Is Not Supported(CSG00121768)
-SPDM_IT_FW:For empty slots IsEmpty field is shown as No it should be shown as Yes .(CSG00230707)
-Build error in PLDM Library on ARM 4.1 compiler with Atlas FW build environment(CSG00071478)
-Invalid Completion code Error for running script-LearnComponentStateInvalidTransferFlagPLDMType5.py(CSG00149690)
-Phase 15 Coverity Bug Fixes(CSG00092935)
-Some of SAS/SATA drives attached to OEM Aero HBA may not be reported to host(CSG00076717)
-Connector Name displayed as 'Unknown' in HII for NVMe drives behind Switch(CSG00085845)
-SPILIB: Winbond 256MBit maximum page write time increased from rev "A" to rev "B" of their specification(CSG00170747)
-pl: firmware hang occurs in UBM command error case(CSG00072841)
-Coverity defect fix in FPE code.(CSG00235474)
-RDE - Controller information is not getting launched in REST client(CSG00099613)
-Fix SPDM library for Get_Digest, Challenge.(CSG00053409)
-Update the SPDM print index properly before adding the prints to ring buffer(CSG00335886)
-Resetting the event counters in Ext. SAS/PCIe IO Unit Page 250 fails(CSG00150901)
-0x6001 Fault while running IOs and cable pull test(CSG00040422)
-[SPDM] Fix compilation #include "iopPlatSecCertMgMt.h" case sensitive issue(CSG00109315)
-SPDMLIB: Reduce number of arguments passed to IT FW debug print functions(CSG00335615)
-IOP: Trace buffer image has extra "CFG string(CSG00051124)
-Update NVDATA Major Version on PH16 point release(CSG00309322)
-(SATA Only) SCSI ATA Passthrough command with set feature command to set the drive in standby_y state sets it to standby_z state.(CSG00080256)
-Release Automation: Web page button not detected in script.(CSG00137712)
-pl: NVMe: D062 fault during NVMe init(CSG00083594)
-PLDM Type 6: Fix "RedACT" tool reported observations(CSG00080427)
-Check in SpdmDebug.h for IT(CSG00074108)
-Updated CoreDump specific functions to run from OCM memory and enabled XMEMXOPY(CSG00093703)
-pl: NVMe: E429 fault on register read failure(CSG00098345)
-SBLIB: Change bool type to int type in API parameter to maintain compatibility(CSG00100308)
-PLDM Type 2: Resource associated major schema count is incremented incorrectly(CSG00074150)
-[PLDM] IT HBA with latest PLDM library faults(CSG00102618)
-Aero BST: Manage NVMe drive link up timing(CSG00228186)
-SPDM library to remove %s for any print as IT does not support %s print string.(CSG00061353)
-Import certificate command with out seal option is failing for slots 0 & 1.(CSG00228127)
-[Aero/Ventura] MCTP discovery fails after unload and load of MCTP driver in BMC(Board Management controller)(CSG00058897)
-ventura build issue with PL PCI DEVICE feature disabled(CSG00286358)
-When performed export csr for all 8 slots in batch observing for few slot command is success and for other it is failure.(CSG00421812)
-PL: Removal of NVMe Drive that Failed NVMe Init Doesn't Work Correctly(CSG00103998)
-Aero Seeing "SpdmReadCertForSlot[277]:[Error] Certificate Read Failed" on IT card after Controller Resets(CSG00253315)
-MAC verification failed due to inconsistent secure ID(CSG00309854 (Port Of Defect DCSG00309857)
-pl: backend PCIe: 'pl pci devlnk' is missing from the 'pl dbg' dump(CSG00052268 (Port Of Defect DCSG00052348)
-PL: Initial MPI driver error injection can cause the Managed Switch's SES to not be exposed to OS(CSG00045593(Port Of Defect DCSG00045725))
-NVMe devices VPD page 83 NAA descriptor may conflict with EUI64 ID reported(CSG00148775 (Port Of Defect DCSG00153702)
-Remove LogSpecific member in the structure 'IOPI_LOG_DETAIL(CSG00318366 (Port Of Defect DCSG00318944)
-Ventura; Add code to prevent downgrade from phase 14 to previous phases for winbond(CSG00059594 (Port Of Defect DCSG00061399)
-Aero: pl: SATA device may not link up following a link down(CSG00054906 (Port Of Defect DCSG00073959)
-"iop show cfg all" command captured by core-dump is zero(CSG00047928 (Port Of Defect DCSG00050673)
-PL: Blind retries by MegaRAID FW when PL is in out of resource condition results in IOs to MS-SES exhausting retries(CSG00033753 (Port Of Defect DCSG00046628)
-pl: backend PCIe: switch rediscovery fails with certain switch configurations(CSG00061635 (Port Of Defect DCSG00062706)
-PL NVMe : NVMe repair operation fails with metadata(CSG00112303 (Port Of Defect DCSG00121425)
-VSES SES Page 02h reports Unknown (06h) Element Status for some Array device elements in a wide DFC slot(CSG00069091 (Port Of Defect DCSG00086818)
-UBM: Incorrect slot number enumerated for a DFC on 3 x4 DFCs UBM config(CSG00048027 (Port Of Defect DCSG00048742)
-SATA only : Controller hang is observed due to recursive function call.(CSG00139294 (Port Of Defect DCSG00226371)
-SPDMIT: Return appropriate error to SPDM Lib when read certificate from security page 0 fails(CSG00299079 (Port Of Defect DCSG00306949)
-pl: NVMe: unexpected NVMe init failure if LBA 0 is inaccessible(CSG00120588(Port Of Defect DCSG00121315)
-PL NVMe : PCI task management is not getting completed.(CSG00231422 (Port Of Defect DCSG00245538)
-pl: NVMe: incorrect sense key is returned for Access Denied NVMe status(CSG00063924 (Port Of Defect DCSG00069167)
-Ventura: The host PCIe link width may be narrower than expected(CSG00078678 (Port Of Defect DCSG00093473)
-Ventura/Mercator: pl: direct attached SAS or SATA device may not be discovered(CSG00408109 (Port Of Defect DCSG00427398)
-Some of the drives not listed under Widows OS Disk Management.(CSG00096508 (Port Of Defect DCSG00102661)
-PL SATA: Sanitize operation is completed before actual completion from drive.(CSG00119155 (Port Of Defect DCSG00126831)
-pl: NVMe: Select field used during NVMe init without verifying support(CSG00050182 (Port Of Defect DCSG00051206)
-Incorrect slot mapping on UBM backplane with additional DFCs support(CSG00077969 (Port Of Defect DCSG00082256)
-LED Blink/Unblink operation fails on certain Slots in UBM using MPI SEP Request(CSG00282826 (Port Of Defect DCSG00299898)
-Aero A0: External cards do not support PCIe and SRIS by default(CSG00131571 (Port Of Defect DCSG00143420)
-pl: NVMe: Drive Firmware update fails on mode 0xE(CSG00044028 (Port Of Defect DCSG00052008)
-Back out changes of ER DCSG00029633 that limits VSES devices to 2(CSG00053379(Port Of Defect DCSG00054368)
-[SATA Only] SCSI Start Stop Unit command with power condition active fails.(CSG00349970 (Port Of Defect DCSG00405776)
-Atlas Behind Aero: PL Fault 0xEC1A When Performing Backend PCI Resets From Diagnostic Code(CSG00042688 (Port Of Defect DCSG00147003)
-BSOD when running CoreDump with Aero connected to Atlas switch(CSG00042497 (Port Of Defect DCSG00044353)
-Invalidate slot not working for IT SPDM(CSG00131485 (Port Of Defect DCSG00139744)
-Drive Discovery failed with Port Hot-swap on Aero16e controller(CSG00042446 (Port Of Defect DCSG00052013)
-Fail to read device and link related counters from Page 250(CSG00080856 (Port Of Defect DCSG00096620)
-[Aero/Ventura] Bootloader corruption with firmware download and DC cycle in loop.(CSG00238233 (Port Of Defect DCSG00245453)
-Aero: Firmware Download should return success with loginfo indicating POR is necessary(CSG00055371 (Port Of Defect DCSG00065882)
-PL: Over 250+ power cycles of managed switch (Atlas) causes an associated SES to be inaccessible(CSG00048699 (Port Of Defect DCSG00059743)
-ParentDevHandle value calculated for given Phy Number is incorrect for Direct Attached Devices in Event Replay logic(CSG00299632 (Port Of Defect DCSG00299897)
-[Aero][PLDM] FW version reported wrongly to BMC( Board Management Controller) over out of band(CSG00050201(Port Of Defect DCSG00051130)
-[Aero/Ventura] Unused phys are managed by VSes in SGPIO BP mode(CSG00151021 (Port Of Defect DCSG00225221)
-VSES page 02h reports incorrect status for linkup failed array device element on certain UBM slots(CSG00112320 (Port Of Defect DCSG00127720)
-Ventura B0: Device discovery fails on 9400-16e(CSG00045385 (Port Of Defect DCSG00045779)
-PL : 0x7008 fault seen when booting the bad clocked controller connected to Atlas(CSG00114774 (Port Of Defect DCSG00121424)
-Drives connected behind external card with VSES disabled, failed to detect in Linux OS(CSG00350402 (Port Of Defect DCSG00363781)
-Aero: backend PCIe: link failure after PCIe IO Unit Page 1 link disable(CSG00050164 (Port Of Defect DCSG00051710)
-Expander attached devices not reported to host if enclosure slot ordering is enabled in event replay.(CSG00108094 (Port Of Defect DCSG00111584)
-pl: NVMe: EC0E fault after drive pull during NVMe init(CSG00114179 (Port Of Defect DCSG00127917)
-PL: 2 Atlases in single MPT mode with 2 host ports each will have drives on one switch not mapped to that Atlas's SES Page 0Ah(CSG00054949 (Port Of Defect DCSG00062379)
-0xD101 Fault observed running non-RW IOs to NVMe devices with drive push-pull(CSG00062701 (Port Of Defect DCSG00071043)
-PH14 Windows Driver: on 2016,19H2 OS,Getting BSOD for fault command(CSG00048607 (Port Of Defect DCSG00053744)
-Upto 90% performance drop with expander attached configuration.(CSG00153860 (Port Of Defect DCSG00215210)
-ExtManPage41 TX Values are not being applied / run by AERO SERDES(CSG00311524 (Port Of Defect DCSG00313276)
-[NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive(CSG00136092 (Port Of Defect DCSG00243680)
-PL: PCIe switch discovery can cause processor exception when setting enclosure information(CSG00063530 (Port Of Defect DCSG00063552)
-PL backend PCIe: PL fault 0xD308 is observed with Aero and Atlas connected in bad clock environment(CSG00134207 (Port Of Defect DCSG00137697)
-Aero: backend PCIe: link failure following link down(CSG00043821 (Port Of Defect DCSG00048732)
-MCTP: SenseData not available for a failed command sent over OOB.(CSG00054655 (Port Of Defect DCSG00057485)
-Number of initiators gets decremented to 0xFF(CSG00051990 (Port Of Defect DCSG00053834)
-Quotes present in NVDATA XMLs(CSG00045528 (Port Of Defect DCSG00045606)
-Incorrect Man page 7 Phy-Slot mapping set for 9500-xx channel HBAs(CSG00061349 (Port Of Defect DCSG00062359)
-[Aero] Change the Manpage 7 Phy to Connector settings and Disable NVMe support in ManPage9(CSG00031186 (Port Of Defect DCSG00044352)
-[SPDM IT] Return actual size of certificate chain content to SPDM LIB(CSG00233805 (Port Of Defect DCSG00245634)
-PL SATA only : SATA init timeout observed due to drive taking longer to respond to sanitize status ext(CSG00225935 (Port Of Defect DCSG00227376)
-IOC Exceptions not getting cleared after flashing the BIOS image with correct ROP version(CSG00226395 (Port Of Defect DCSG00227987)
-AXI access errors causing FW asserts or faults due to invalid SATA passthrough commands(CSG00215338 (Port Of Defect DCSG00243095)
-(SATA Only) SCSI ATA Passthrough command with data transfer fails.(CSG00120976 (Port Of Defect DCSG00121420)
-Locate PD fail on SGPIO enclosure when GroupId is disabled in Nvdata.(CSG00034489 (Port Of Defect DCSG00041403)
-Fault 0x6109 while running IOs and device remove test.(CSG00082201 (Port Of Defect DCSG00083887)
-PL : Missing drives during AC power cycle test(CSG00275868 (Port Of Defect DCSG00301822)
-NVMe Init Error List has drive entry missing when multiple Bad PDs are inserted(CSG00113697 (Port Of Defect DCSG00121316)
-[Aero/Ventura]Allow the backplane detection state machine to retry the FRU detection.(CSG00219908 (Port Of Defect DCSG00222984)
-(SATA Only) MODE SELECT (6|10) to SATA drive with DEXCPT set fails if DEXCPT is already set.(CSG00131574 (Port Of Defect DCSG00134494)
-Toolbox clean command sent to clean flash fails.(CSG00059302 (Port Of Defect DCSG00062455)
-[VSes] SCSI State not correctly set for some error response to SCSI commands.(CSG00312554 (Port Of Defect DCSG00324764)
-PL: TM Device Reset to NVMe drive under out of LMID condition can cause Data Abort Exception to the processor(CSG00036763 (Port Of Defect DCSG00048676)
-Index out of range is observed for print in ring buffer logs(CSG00134669 (Port Of Defect DCSG00139071)
-Aero_scrutinycli: "Device -c" command output is not matching with the firmware cli parameter values in Aero behind atlas configuration.(CSG00121852 (Port Of Defect DCSG00127910)
-PL Fault 0000e40e while booting OS with bad NVMe drive(CSG00109053 (Port Of Defect DCSG00118379)
-NVMe devices VPD page 83 NAA descriptor may conflict with EUI64 ID reported(CSG00060347 (Port Of Defect DCSG00136105)
-Moving Controller From Single VSES config to a multi-VSES config causes issues in windows OS.(CSG00071784 (Port Of Defect DCSG00080399)
-[VSes] Element status set to 'Unknown' in SES page 2 of VSES for some phys where nothing is connected.(CSG00333163 (Port Of Defect DCSG00343847)
-PL NVMe : PCI task management is not getting completed.(CSG00231422 (Port Of Defect DCSG00266052)
-Fix ring buffer decoder's slowness with decoding a trace buffer(CSG00050675 (Port Of Defect DCSG00051120)
-NVMe repair command fails with 'No drive support for recovery' loginfo(CSG00129498 (Port Of Defect DCSG00137668)
-NVMe drives not discovered and Event replay in enclosure slot mapping not working as expected.(CSG00078212 (Port Of Defect DCSG00080846)
-As part of the Device Add\Removal Event, the enclosure handle passed on by the PL FW to the upper layer is incorrect.(CSG00298128 (Port Of Defect DCSG00299896)
-[Aero] Fault 0xA03 observed when updating FW with a bad NVMe drive in the topology(CSG00132639 (Port Of Defect DCSG00136250)
-pl: NVMe: chain to PRP SGL for non-read/write IO may be handled improperly(CSG00408313 (Port Of Defect DCSG00427399)
-scattered file changes to include some debug prints and also minor change to debug print(CSG00057124 (Port Of Defect DCSG00057818)
-Firmware asserts during customer specific UBM Backplane enumeration.(CSG00058770 (Port Of Defect DCSG00061183)
-[Aero][AutoPort Enable] Erase persistent config pages is not retaining the VPD and sas address(CSG00074378 (Port Of Defect DCSG00114250)
-Import certificate command is failing via In-band(CSG00212544 (Port Of Defect DCSG00215132)
-[Aero][PLDM] Update to Latest PLDM library v13(CSG00137629 (Port Of Defect DCSG00138016)
-AXI access error from TxDMA engine when certain errors occur during Task Management processing(CSG00078508 (Port Of Defect DCSG00235435)
-SPDM IT:SPDM BMC bring up on P2 server(CSG00238540 (Port Of Defect DCSG00241397)
-SATA Only: Command timeout observerd on SATA drives(CSG00344039 (Port Of Defect DCSG00356005)
-Aero: PL with newer Atlas FW (4.2) has extra slot number in the Atlas enclosure(CSG00284238 (Port Of Defect DCSG00291431)
-Aero A0: In Windows OS redundant disks detected when controller connected to Elrond Ex1(CSG00061406 (Port Of Defect DCSG00065448)
EnhancementRequests:
-PL: Support Managed Switch (Atlas) slot range VSEC command for its single MPT mode(DCSG00071626)
-BST: Add Ventura activity server and enclosure to test config(DCSG00079826)
-SEA IT TRNG HW enable(DCSG00098752)
-Bring up OEM Specific BST Server(DCSG00325843)
-Enable UBM BST support for Aero(DCSG00063407)
-Health Data Events - Create counters for various Health Data Events(DCSG00078912)
-Re-naming few functions in module-object-verb format(DCSG00027061)
-Ventura/Aero: Add Ext. Man Page 48 to store CoreDump options(DCSG00026309)
-Add Aero/Sea Info to Ventura Summary Release Notes(DCSG00077941)
-BST: Add support for Drive Control Modules to cable breaker test cases.(DCSG00256443)
-Aero3: SecureBoot BIOS Image Download with new Key is failing(DCSG00233694)
-Platform related configuration changes updation(DCSG00039844)
-Port secureSignBin.exe for MARGAY signing to GCP server environment(DCSG00040377)
-Update HWBIC Generation XMLs for CQ9(DCSG00100142)
-SPDMLIB: OEM requested to not report Get Measurement Capable(DCSG00323053)
-Release Automation: Submit auto-BST jobs(DCSG00091315)
-Resolving the compilation conflicts while integrating the library with FW(DCSG00045448)
-Certificate read and Write wrapper functions & Slot management(DCSG00105005)
-Automate Build Job and Release Job Submission Process(DCSG00045139)
-Remove A0 raw fw rawA0.fw file from release scripts(DCSG00211914)
-BST: Aero Activity server with Atlas switch(DCSG00225036)
-Define Macros/inline functions(DCSG00027051)
-BST: A test to verify slot counts(DCSG00238332)
-MPI changes to configure backend ASPM(DCSG00051277)
-Avenger support for the LIBSPDM(DCSG00081168)
-UBM BST: Ensure UBM BP details reported by FW are accurate.(DCSG00227823)
-Add IT+Expander controller to OEM BST server(DCSG00286591)
-pl: SATA: vendor specific ATA Standby handling(DCSG00074400)
-Aero/Ventura: Enable easier debug when SPI FLASH is bad(DCSG00058537)
-Log SPDM events entries in log page 0(DCSG00139949)
-PL: NVMe Drive Repair(DCSG00055563)
-Implement a secure version of memset for SPDM code to use to zero out buffer(DCSG00208365)
-Automate version update stage in release process(DCSG00122144)
-SPDM LIB: Implement version scheme(DCSG00072483)
-Aero multi-party signing partial signing of images(DCSG00048670)
-PL logic to create VSES instances per Backplane number(DCSG00069245)
-SPDM_LIBRARY: Change for SPDM Policy Implementation(DCSG00097417)
-[Aero][Ventura] Sign windows build applications and avoid antivirus from deleting them.(DCSG00025757)
-FD should move to DOWNLOAD state immediately upon successfully sending the response of UDATE_COMPONENT.(DCSG00046402)
-Allow General Processing Failure from Atlas on unsupported commands to not result in 0xEA20 fault(DCSG00170698)
-Added SPDM lib to IT FW code base and handle MCTP VDM SPDM commands(DCSG00063688)
-MBEDTLS LIB: Enhancement to source of randomness for generating key pair(DCSG00148786)
-Define APIs for PLDM debug infrastructure and Implements debug routine for PLDM Base(DCSG00026992)
-[Aero] [SPDM] Support Export Certificate Signing Request command(DCSG00063692)
-Ventura/Aero: Update SPI flash test to print better failure information(DCSG00070917)
-Remove cdi get for Avenger(DCSG00152679)
-Port changes from old db to new DB(DCSG00014692)
-BST: set SRIS after every fw download(DCSG00150322)
-Signing Linux executables via GPG method in HSM(DCSG00077215)
-PL: Coordinate reset on Atlas FW update to limit IO disruption to NVMe drives behind Atlas(DCSG00097342)
-MbedTLS: Explicitly make enumerator value of enum type to 4-byte value(DCSG00054557)
-MBEDTLS LIB: Rename sha256.h header file to avoid conflict with MR FW sha256.h header file(DCSG00068675)
-Enable 24 PCIe device support for Aero External boards.(DCSG00278073)
-SPILIB 2.0: Add capability to support Winbond Parts with Factory Quad bit Disabled(DCSG00140236)
-Release Automation: Validate FW Header post Package Creation(DCSG00055071)
-CM Utility to perform automated Deliver and Rebase actions(DCSG00083856)
-Release Automation: create Aero IT FW only Release Order Package(DCSG00066845)
-SPILIB 2.0: Add support for Block Protect bits configuration(DCSG00170752)
-SPILIB2: Add support for Macronix MX25U25691G part(DCSG00068680)
-SPDM LIB: Implement SPDM Get Measurement command(DCSG00234758)
-CFGI: support build persistent config region from MPB2(DCSG00077614)
-Disable hardware debug ports(DCSG00143569)
-pl: backend PCIe: PCIe Hinting(DCSG00050640)
-BST: Config update with Blr servers data for slot count(DCSG00248916)
-Check if all BP slots and drives are discovered after FW upgrade(DCSG00087155)
-Aero/Ventura: Add CLI to test QE bit modification(DCSG00148653)
-pl: NVMe: handle Namespace Not Ready error during NVMe init(DCSG00071652)
-MbedTLS Lib: disable file system related functions & enable memory allocation and prints functions to be compiled in CPP environment(DCSG00060384)
-Modify the UBM BST code with respect to new BST scrutiny APIs.(DCSG00063258)
-CDI & Key Generation source integration with IT FW(DCSG00063690)
-Added Carriage Return (\r) in PLDM common library debug strings(DCSG00069752)
-Update PLI Spec(DCSG00008045)
-pl: backend PCIe: examine BAR attributes following endpoint/switch reset(DCSG00060688)
-UCM Action tool feature to support rebase using latest baseline(DCSG00125616)
-Update Sea Channel XMLs to PCI Device ID 0xE6(DCSG00079238)
-SECUREBOOT_LIB: Move hardware touch (ApSha HASH & HMAC and OTP eFuse Read) from MR SPDM code to Secure Boot Lib(DCSG00082166)
-Implement changes to secureSign signing tool and infrastructure to support mixed list of PublicKeys that are from SCGCQ and DCSG.(DCSG00105430)
-NVMe Drive Init failure Error Reporting(DCSG00055566)
-MBEDTLS LIB: Change large local variable memory allocation from the stack to dynamic memory allocation from the heap(DCSG00087564)
-Aero/Ventura: Move DMCore hardware file to common(DCSG00007511)
-Add Avenger support for libmbed tls.(DCSG00051695)
-pl: NVMe: handle Namespace Not Ready error during NVMe init (part 2)(DCSG00075871)
-BST: Update scripts to run Customer fw on channel adapter(DCSG00082887)
-Enable 24 NVMe drive support by default for external controllers.(DCSG00305223)
-Implement event message supported, event message buffer size and platform event message for PLDM type 2 - monitoring and control app.(DCSG00149551)
-Resolving the compilation conflicts while integrating the library with FW(DCSG00045470)
-PLDM - Add Linked List Traverse utility and correct TID API function(DCSG00165389)
-UpdateVersion tool to change and update version information in ClearCase(DCSG00072590)
-Implemented change to use FTP instead of UNC for upload / download of unsigned / signed artifacts to workaround firewall issue.(DCSG00129388)
-[Aero][SPDM] IOP framework to support CFGI Reads and Writes(DCSG00076512)
-[SPDM]SBlib upgrade to 2.02(DCSG00091314)
-Provide Configurability For SPDM Library(DCSG00045604)
-Added documentation for some scenarios(DCSG00027067)
-MBEDTLS LIB: Implementation: Use CDI to generate ECDSA key pair(DCSG00067411)
-[BST] Add the corrective action in BST scripts to check if SAS address is retained after persistent erase(DCSG00216341)
-BST: Verify version control file from fw(DCSG00268618)
-SPDM_LIB: Support to build Challenge buffer with multiple GET_CERTIFICATE/CERTIFICATE_RESPONSE(DCSG00225175)
-Update Version descriptors for standard inquiry data of SATA and vSES devices(DCSG00037325)
-[Aero SPDM] XSD changes to support SPDM version in a new manufacturing page(DCSG00103227)
-Update NVMe to SCSI Error code translation.(DCSG00098339)
-Added "pl serdes tx" and "pl serdes rx" command(DCSG00053828)
-Support for NVMe Firmware Download when the image size exceeds the SNTL Transfer limitation.(DCSG00053656)
-MBEDTLS LIB: Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust(DCSG00216867)
-Shrink MbedTLS library size(DCSG00059001)
-Log 0 SPDM events for certificate slot & key management(DCSG00322202)
-Support MPB2 write/read into manufacturing region(DCSG00063677)
-PLDM Type 2 - Implement support for dynamic PDR repository change(DCSG00165393)
-PLDM: Implement PLDM Type-6 library API and commands(DCSG00064565)
-Fix Mbedtls build scripts to accommodate Aero and Avenger(DCSG00150272)
-PLDM library support to report multiple PLDM App versions to BMC(DCSG00026969)
-Correcting the print function configuration(DCSG00047741)
-XSD and NVDATA changes to support SPDM manufacturing and Security pages(DCSG00063680)
-BST: Customer specific Release/Activity BST at BLR(DCSG00064578)
-SECUREBOOT_LIB: Move SRK and CCR eFuse register access functions to SBLIB(DCSG00086765)
-Package Stamping Verification(DCSG00096506)
-PLDM Type 6: Add debug strings for Type-6 library(DCSG00065842)
-Implement customSign.exe CLI wrapper utility to help customers sign with their private key(DCSG00234646)
-Release Automation: Integrate utility for deliver/rebase into release scripts.(DCSG00094677)
-Config file changes to including prints(DCSG00047716)
-BST: Customer Aero based ROP BST and setup at BLR(DCSG00109334)
-pl: backend PCIe: add debug print for a discovery failure case(DCSG00083082)
-Implement support for Cross certificate and command - Windows signing using CNG Provider with HSM Protected Key(DCSG00030211)
-Release Automation: updates for rebase operation(DCSG00134475)
-MbedTLS lib integration with IT FW(DCSG00063687)
-Release Automation: Integration of all script modules(DCSG00120937)
-MBEDTLS: Implementation: Implement Subject Name validation for CSR (Certfificate Signing Request) and CSR generation(DCSG00069942)
-Implemented secureSignCNG.exe CLI signing tool for Windows Signing.(DCSG00023491)
-Providing Link and Device Related Counters(DCSG00056834)
-PLDM: Implement generic string and linked list utility functions(DCSG00056271)
-Aero3: Harden Managed Switch SES (Atlas) SES Page 0Ah translation with error injection framework(DCSG00037053
-Release Automation: Automate state transitions for ReleaseOrder(DCSG00035457)
-ComboSerdes: add functionality for bypass ready waiting(DCSG00167482)
-Aero SPDM Sblib change: provide sblib interface to disable specified HW debug port.(DCSG00166877)
-Serial mode support for S25FL512S SPI flash part(DCSG00054211)
-MBEDTLS LIB: Implement version scheme(DCSG00072481)
-Aero: Change XMEMCOPY default to disabled in Aero(DCSG00082841)
-PLDM: Implement Redfish PDRs and APIs(DCSG00060505)
-SPDM library: Adding PLDM print module style.(DCSG00060323)
-PL UBM support UBM for PCIe SW upstream port config(DCSG00120726)
-Add SasSerdesCtl0_7 registers to pl serdes(DCSG00069982)
-Implement Debug routines for PLDM Type-5 Module(DCSG00027039)
-pl: NVMe: update Block Limits VPD page translation(DCSG00055387)
-CFGI support for write/read into manufacturing region MPB2.(DCSG00065597)
-Add support for C++/CPP compile for libspdm(DCSG00051200)
-[Aero IT SPDM] Attestation policy at the boot-up time.(DCSG00063691)
-Add support for signing MegaRAID Legacy BIOS CU Images (CTLR) images(DCSG00143847)
-[IT SPDM] Parse certificate to X.509 V3 Standard and verify digital signature to affirm chain of trust(DCSG00218564 (Port Of EnhancementRequest DCSG00322020)
-Aero Secure Boot: Add Key Update Pending Check for 'COMPLETE' Image Download(DCSG00241566 (Port Of EnhancementRequest DCSG00250024)
-Advertise certain Secure Boot Properties using a config page for Application to be able to display it(DCSG00078835 (Port Of EnhancementRequest DCSG00093843)
-Enhancement to source of randomness for generating key pair(DCSG00208477 (Port Of EnhancementRequest DCSG00250093)
-[IT SPDM] Implement client APIs for SPDM Get Measurement command.(DCSG00256411 (Port Of EnhancementRequest DCSG00293435)
-Aero SAS Performance Enhancement on AMD Rome as part of PR(DCSG00064583 (Port Of EnhancementRequest DCSG00065934)
-SPDM IT: Add memory allocation/free for SPDM_LIB(DCSG00229260 (Port Of EnhancementRequest DCSG00241396)
-Modify Ventura Build scripts to add a new Signed image with different AVSO Setting in FW RO(DCSG00231216 (Port Of EnhancementRequest DCSG00231535)
-[SPDM IT] Export CSR & Import Cert Open & Close Session(DCSG00221406 (Port Of EnhancementRequest DCSG00257575)
-Update the event logging when the "CoreDump" region is erased from ScrutinyCLI command(DCSG00367325 (Port Of EnhancementRequest DCSG00418780)
Version 14.125.05.00-4
---------------
BIOS Firmware UEFI Driver
9.27.00.00 14.00.04.00 14.00.01.00
Fixes：
code no fix
Version 14.125.05.00-2
---------------
BIOS Firmware UEFI Driver
9.27.00.00 14.00.04.00 14.00.01.00
Lenovo Storage Host-Bus-Adapter (HBA) SLES 15 Driver
12Gb HBA SAS/SATA/SSD Driver for Linux
NOTE TO SERVICE - Reference RETAIN N/A
Supported Controllers:
- ThinkSystem 430-8i SAS/SATA 12Gb HBA (7Y37A01088)
- ThinkSystem 430-16i SAS/SATA 12Gb HBA (7Y37A01089)
- ThinkSystem 430-8e SAS/SATA 12Gb HBA (7Y37A01090)
- ThinkSystem 430-16e SAS/SATA 12Gb HBA (7Y37A01091)
- ThinkSystem 430-8i SAS/SATA 12Gb Dense HBA (NA-StarkSASHBA)
ThinkSystem 440-16e SAS/SATA PCIe Gen4 12Gb HBA for 4Y37A09724
ThinkSystem 440-16i CFF SAS/SATA PCIe Gen4 12Gb Internal HBA for 4Y37A09725
ThinkSystem 440-8i SAS/SATA PCIe Gen4 12Gb HBA for SR17A98375
ThinkSystem 440-16i SAS/SATA PCIe Gen4 12Gb HBA for SR17A98376
version 46.00.01.00-- Moderate Impact/Low Probability of Occurrence
-----------------------
Ph23
Defects:
-mpt3sas: Fix use after free in _scsih_expander_node_remove(DCSG01194819)
-Host Diag Reset and SBR synchronization.(DCSG01372871)
-System crash observed on doing firmware upgrade/downgrade on IT controller.(DCSG01383945)
-mpt3sas: Fix use-after-free warning.(DCSG01324921)
-Trace buffer registration is getting failed on PEX89000 Series's MPT Endpoint.(DCSG01255174)
-Built mpt3sas driver under RHEL 8.7 failed with error.(DCSG01427265)
-Soft lockup with shared host tag enabled driver with heavy I/O stress.(DCSG01309377 (Port Of Defect DCSG01324918))
EnhancementRequests:
-IT driver Build kit support for RHEL 8.7 - SAS3.5 to generate driver binaries.(DCSG01232299)
-Don't change the normal dma mask to 32bit when any pool cross the 4gb boundary.(DCSG01187986)
-Removing OS Support for Linux.(DCSG01260283)
-Open Euler OS's support is getting dropped.(DCSG01276040)
-Added mpt3sas driver support for respinned RHEL9.0 RT kernel.(DCSG01352287)
-Add mpt3sas driver OS support for RHEL 9.1 GA.(DCSG01364085)
-Add mpt3sas driver OS support for RHEL 9.1 GA.(DCSG01232309)
-Created a Fusion OS 22_22.0.1 buildkit to generate driver binaries.(DCSG01225110)
-Add RHEL9 OS buildkit to build binaries for RHEL9 OS's.(DCSG01225149)
-Remove the usage of dma_get_required_mask API and directly set the DMA mask to.(DCSG01336803)
-Add mpt3sas driver support Fusion OS 22_22.0.1 OS.(DCSG01267797)
-Support for additional IOCTL to set SBR Reload bit in the Host Diagnostic register.(DCSG01295702)
-Add IT Linux driver buildkit for latest RHEL9.0 GA support.(DCSG01344116)
-make the mpt3sas driver compatible with upstream 5.19 kernel.(DCSG01260214)
-Drivers: Increase SATA Initialization timeout to be specified by NVDATA (32 sec default.(DCSG01383804)
-Add mpt3sas driver support for RHEL 8.7 GA.(DCSG01361008)
-Update AutoBST Server Environment from RHEL7 OS to RHEL8 OS.(DCSG01294329)
-Added SLES15 SP4 OS support.(DCSG01132147 (Port Of EnhancementRequest DCSG01228951)
-Enhanced SLES15 buildkit for generating driver binaries for SLES15 SP4 OS.(DCSG01227071 (Port Of EnhancementRequest DCSG01228422)
-Enhanced rhel8 buildkit to support RHEL8.6 OS.(DCSG01219245 (Port Of EnhancementRequest DCSG01225175))
-IT Linux Driver : Added driver support for resppined RHEL9.0 GA support.(DCSG01344299 (Port Of EnhancementRequest DCSG01352298))
-Increase cmd_per_lun value to reduce the contiguous memory requirement for each devices.(DCSG01177689 (Port Of EnhancementRequest DCSG01187998))
version 42.00.01.00-- Moderate Impact/Low Probability of Occurrence
-----------------------
Ph22
Enhancements:
-Enhanced SLES15 buildkit for generating driver binaries for SLES15 SP4 OS.(DCSG01227071)
-Add RHEL9 OS buildkit to build binaries for RHEL9 OS's.(DCSG01225153 (Port Of EnhancementRequest DCSG01225149))
-Added SLES15 SP4 OS support.(DCSG01245746 (Port Of EnhancementRequest DCSG01132147))
-Add driver support for RHEL9.0 GA OS.(DCSG01245747 (Port Of EnhancementRequest DCSG01132123))
version 39.00.04.00-- Moderate Impact/Low Probability of Occurrence
-----------------------
Ph20
Defects:
-mpt3sas: Fix - One vSES device addition to OS is missing when two vSES devices are configured in IOC.(DCSG00936126)
-mpt3sas: Fix - SATA queue depth limited maximum to 32 even though HBA firmware sets its more than 32.(DCSG00966032)
-Ph20: Fix structurally dead code reported by Coverity.(DCSG00987309)
-Ph20: Fix Coverity Reported defects:.(DCSG00969837)
-Ph19: Upstream Port : mpt3sas: Do not use GFP_KERNEL in atomic context.(DCSG00935988)
-mpt3sas - Fix the endianness of ActiveCablePowerRequirement while displaying active cable event information.(DCSG00832919)
-Ph22 mpt3sas: Disable Shared Host Tag Support.(DCSG01106634 (Port Of Defect DCSG01106690))
-Kernel panic observed while performing power cycle operation on drives connected to expander.(DCSG01048756 (Port Of Defect DCSG01058120))
-Timestamp is not properly populated.(DCSG01039799 (Port Of Defect DCSG01040695))
-mot3sas: Fix the junk characters that get displayed while printing ChipName.(DCSG00735107 (Port Of Defect DCSG00914072))
-System falls into read only mode while doing firmware downgrade operation.(DCSG01053915 (Port Of Defect DCSG01057285))
-mpt3sas - Fix dma_pool_free PCIe SGL pool (bad dma) messages.(DCSG00837488 (Port Of Defect DCSG00907750))
EnhancementRequests:
-mpt3sas: Gracefully handle HBA firmware fault while scanning the devices during IOC Initialization.(DCSG00428569)
-Ph19: Upstream port: fix ReplyPostFree pool allocation.(DCSG00908392)
-mpt3sas: Add driver support for SLES15SP3 OS.(DCSG00961074)
-Ph20: mpt3sas driver support for RHEL 8.4 OS.(DCSG00944572)
-Add BuildKit Support for RHEL 8.5.(DCSG01076786)
-Ph19: Add OpenEuler 20.03 LTS OS Support.(DCSG00835041)
-mpt3sas: Added support of shared host tagset.(DCSG00707728)
-mpt3sas: add io_uring iopoll support.(DCSG00919665)
-Ph19: Remove logging BIOS version in the kernel log.(DCSG00648679)
-mpt3sas: Gracefully handle HBA Firmware faults during first half of IOC Initialization.(DCSG00757752)
-Add OpenEuler 20.03 SP1 LTS Buildkit support (Driver RPM Binary).(DCSG01004086)
-Port from Upstream: mpt3sas: Move a little data from the stack onto the heap.(DCSG00943359)
-mpt3sas - Use the Firmware recommended device queue depth instead of using hard coded values.(DCSG00939265)
-Ph18: SLES15SP3 RPM WA to create initramfs after rpm installation.(DCSG00990761)
-Ph20: mpt3sas driver support for RHEL 8.5 OS.(DCSG01079682)
-Update OpenEuler buildkit to support x86_64 and aarch64 builds from VBAS.(DCSG01033094)
version 37.00.02.00-- Moderate Impact/Low Probability of Occurrence
-----------------------
Ph18
Defects:
-mpt3sas: Fix the bug in determining SDD or HDD drive logic.(DCSG00405885)
-Fix some of sparse warnings and warnings from build flag W=1.(DCSG00433486)
-mpt3sas: Return back the UNMAP SCSI command issued to NVMe drives with ILLEGAL_REQUEST sense key if the parameter list length is non zero and less than 24 bytes.(DCSG00317760)
-mpt3sas: Too many virtual_phy objects are allocated even when there is only one vSES is present.(DCSG00405891)
-Address issues from Coverity analyzer..(DCSG00451494)
-mot3sas: Fix the junk characters that get displayed while printing ChipName.()
-mot3sas: Fix the junk characters that get displayed while printing ChipName.(DCSG00735107 (Port Of Defect DCSG00959583).()
-mpt3sas: Fix - One vSES device addition to OS is missing when two vSES devices are configured in IOC.(DCSG00936126 (Port Of Defect DCSG00959573))
-mpt3sas - Fix dma_pool_free PCIe SGL pool (bad dma) messages.(DCSG00837488 (Port Of Defect DCSG00959578))
EnhancementRequests:
-Ph17 : Add Citrix Xenserver 8.2 OS Support.(DCSG00283053)
-mpt3sas: Remove un-used / Pre-production IDs.(DCSG00347011)
-Add BuildKit Support for RHEL 8.4.(DCSG00971809)
-Phase 18: Add Support for OEL UEK kernels 4.14.35.(DCSG00433355)
-Ph18: Add mpt3sas driver support for SLES15 SP3.(DCSG00972769)
-Ph18: Add mpt3sas driver support for RHEL 8.4 OS.(DCSG00971892)
-Ph17: Periodic Time Sync between the Driver and FW.(DCSG00269087)
-mpt3sas: simplified the code section related to refreshing the hba_port table during host reset.(DCSG00412032)
-Ph18: mpt3sas OS driver support for RHEL 8.3.(DCSG00373406)
-Port from Upstream: mpt3sas: a small correction in _base_process_reply_queue.(DCSG00379898)
-Add Driver Signing Flow for Tier 1 Linux OS (SUSE and RHEL) - IT.(DCSG00373449)
-Phase 18 : RHEL 7.9 OS Driver Support.(DCSG00373540)
-mpt3sas: Save the user configured trigger values in driver trigger pages of NVRAM.(DCSG00235944)
-Port from Upstream - mpt3sas: Fix sync irqs.(DCSG00379897)
-Upstream port: mpt3sas: Don't call disable_irq from IRQ poll handler.(DCSG00346997)
-Ph18: SLES15SP3 RPM WA to create initramfs after rpm installation.(DCSG00990761)
-When HTB is released we never know for what reason buffer is released. Need to add that in drivers so that top layers can fetch those information.(DCSG00373439)
-Ph17: SLES15SP2 OS Support.(DCSG00278037)
-Ph18: Assign bit 1 in drv_support_bitmap sysfs parameter as support flag for Additional Diagnostic query ..(DCSG00404493)
-mpt3sas: multi-port path - Set proper PhysicalPort value while issuing the SMPPassthrough request message.(DCSG00244772 (Port Of EnhancementRequest DCSG00283221))
-mpt3sas: Increase IOCIinit request message timeout from 10s to 30s.(DCSG00432754 (Port Of EnhancementRequest DCSG00432880))
-mpt3sas: enable multi-port path support by default on Sea & Ventura devices.(DCSG00249086 (Port Of EnhancementRequest DCSG00283223))
-mpt3sas: Upstream port: fix ReplyPostFree pool allocation.(DCSG00908392 (Port Of EnhancementRequest DCSG00959581))
-mpt3sas: multi-port path support: Handle vSES device separately as it may have same Port ID as other direct attached device Port ID.(mpt3sas: multi-port path support: Handle vSES device separately as it may have same Port ID as other direct attached device Port ID)
-mpt3sas: Add driver support for SLES15SP3 OS.(DCSG00961074 (Port Of EnhancementRequest DCSG00961941))
version 35.00.02.00 -- Moderate Impact/Low Probability of Occurrence
-----------------------
Fixed:
Update SAS HBA SLES driver to 35.00.02.00, remove raid_class.ko for OSC
mpt3sas - Fix dma_pool_free PCIe SGL pool (bad dma) messages.(DCSG00837488)
version 35.00.01.00 -- Moderate Impact/Low Probability of Occurrence
-----------------------
Ph16
Defects:
-Phase16 - Port Upstream fixes for Reply Pool allocation in NON-RDPQ mode. (Dev Defect).(DCSG00236774)
-mpt3sas: handle the interrupt latency issues while processing the target and LUN reset.(DCSG00244057)
-Fix unwanted messages displaying while using generic src rpm in debian.(DCSG00414316)
-mpt3sas: Don't flush out the outstanding IOs from .remove() in case of ordered HBA removal.(DCSG00055141 (Port Of Defect DCSG00076465))
EnhancementRequests:
-Fix driver compilation issue with 5.5 kernels..(DCSG00071969)
-Code Review: Port from upstream and code Review.(DCSG00087135)
-Ph16 mpt3sas: Add RHEL8.3 OS Support.(DCSG00416036)
-Buildkit Update for RHEL8.2.(DCSG00171494)
-Update Buildkit for SLES15SP2.(DCSG00256383)
-Phase 15: Simplify RDPQ DMA allocation.(DCSG00083296)
-mpt3sas: Cancel the running work also while cleaning up works from firmware event work queue.(DCSG00153595)
-mpt3sas: Capture the MPT3SAS_ADAPTER structure data as part of debugging improvement.(DCSG00070290)
-mpt3sas: Dump system registers for debugging.(DCSG00136289)
-Ph18: Update BuildKit to support RHEL8.3.(DCSG00416071)
-Ph16 mpt3sas: According to MPI spec SenseBuffer, Reply, RequestFrame, ReplyFreeQueue & ChainBuffer must satisfy 4GB boundary restriction.(DCSG00165164)
-Ph15: RHEL7.8 Support for SAS35 Phase 15.(DCSG00075087)
-Ph15: Drop sles12sp2 from OS Support list..(DCSG00071973)
-Phase 16 : RHEL 7.9 OS Driver Support.(DCSG00379891)
-Ph16: RH 7.8 Support.(DCSG00075094)
-mpt3sas: Memset config_cmds.reply buffer with zeros before issuing config page request.(DCSG00134501)
-IT Linux Phase 16: Add RHEL 8.2 OS support (Kernel - 4.18.0-193.el8.x86_64).(DCSG00171492)
-Ph18: Add RHEL 7.9 Build kit support to generate RPM's and DUD:.(DCSG00373755)
-Linux IT Ph15 mpt3sas: Remove usage of device_busy counter when blk-mq is enabled.(DCSG00070285)
-Ph17: SLES15SP2 OS Support.(DCSG00278037 (Port Of EnhancementRequest DCSG00323616))
-Phase 15: Adding RHEL 8.3 Source RPM support.(DCSG00255944 (Port Of EnhancementRequest DCSG00257350))
version 33.00.01.00 -- Moderate Impact/Low Probability of Occurrence
-----------------------
Linux driver-PH14
Defects:
-Print message for invalid and Tampered modes for AERO adapters.(DCSG00046030)
-Phase14 PA2: Fix Coverity reported uninitialized scalar variable:.(DCSG00039059)
-PH14 Linux Driver: NVMe shutdown Timeout observed for a NVMe drive having latency 0xa.(DCSG00033916)
-PH14 LinuxDriver: NVMe Shutdown latency is not matching with the PCIe device page2 value,after updating the FW from PH13 to PH14.(DCSG00033895)
-Update SLES DUD buildkit.(DCSG00105055)
-PH14 Linux Driver: Warnings encountered during installation of driver source rpm package (DCSG00057923).(DCSG00058099)
-mpt3sas: Don't flush out the outstanding IOs from .remove() in case of ordered HBA removal.(DCSG00055141 (Port Of Defect DCSG00118139))
EnhancementRequests:
-mpt3sas: Optimize Linux Driver logging to have ability to debug from first-time capture.(DCSG00034901)
-Upstream port: scsi: mpt3sas: Mark expected switch fall-through.(DCSG00043171)
-IT Linux AutoBST: Add AutoBST infrastructure for IT Linux driver 'mpt3sas'.(DCSG00060120)
-Sign Source RPMs with GPG publicprivate key.(DCSG00057289)
-Ph14: RHEL 7.8 Support.(DCSG00129150)
-Upstream Port: mpt3sas: Select IRQ_POLL to avoid build error.(DCSG00028079)
-Phase 14: Add RHEL 8.2 OS support (Kernel - 4.18.0-193.el8.x86_64).(DCSG00167711)
-mpt3sas: Added module parameter named 'enable_sdev_max_qd' to override sdev queue depth to host's can_queue value.(DCSG00025451)
-Phase 15: Automate SLDPK build and Releases.(DCSG00103269)
-For NVMe devices use RTD3 Entry Latency time as timeout value for nvme shutdown command.(DCSG00026991)
-Ph15 : Add BuildKit suuport for RHEL78.(DCSG00126746)
-Added support for the CoreDump collection on IT-FW fault.(DCSG00027606)
-mpt3sas: developed a phython utility 'decode_ioc_binary_dump.py' to decode the ioc dump collected through debugfs.(DCSG00076209)
-Phase 14: Add SLES12SP5 OS Support.(DCSG00054299)
-IT Linux Phase 14: Add RHEL 8.1 OS support (Kernel - 4.18.0-147.el8.x86_64).(DCSG00047864)
-BuildKit: Sign Source RPMs with GPG publicprivate key.(DCSG00057290)
-Add mpt3sas driver support for Citrix Hypervisor 8.1.(DCSG00065970)
-MPI 2.6: Header file changes associated with Revision 2.6.9 of the specification.(DCSG00024640)
-MPI 2.6: Add additional IOC_State (CoreDump) to allow firmware to dump debug logs without being reset by host.(DCSG00020567)
version 32.00.01.00 -- Moderate Impact/Low Probability of Occurrence
-----------------------
Linux driver-PH13
Defects:
-Seagate Linux MPT3SAS Queue Depth limitation.(DCSG00033868)
-mpt3sas : Toolbox memory move write operation is getting failed.(SCGCQ02139652)
-SAS35 Ph12 mpt3sas : Add RHEL 8 OS support.(SCGCQ02129387 (Port Of EnhancementRequest SCGCQ02128161)
-mpt3sas: Reduce the performance dip depth which will be observed on SATA HDD when any ATA PT command is outstanding.(SCGCQ02131946 (Port Of EnhancementRequest SCGCQ02129874))
-mpt3sas: Fix 0x2666 fault observed while rebooting the server.(SCGCQ02114357)
-Linux Driver: RHEL 6: Warning while installing the rpm package.(SCGCQ02117510)
-mpt3sas: Process SAS DEVICE STATUS CHANGE EVENT event from ISR context.(SCGCQ02121829 (Port Of EnhancementRequest SCGCQ02114044))
-Code optimization and src rpm build kit clean up.(SCGCQ02100212)
-mpt3sas: Fix - App own flag is set even when application has not registered the trace buffer.(DCSG00010203)
-mpt3sas: Fix - don't check for IOC state for fault state & issue diag reset when IOCIinit handshake request failed during host reset.(DCSG00002616)
-mpt3sas: Inbox driver getting loaded after booting into updated RHEL8 kernel.(DCSG00002612)
-Phase 13: Add SLES12SP5 OS Support.(DCSG00055540)
Enhancements:
-mpt3sas: Upstream - add driver support for v5.1 kernel.(SCGCQ02137486)
-mpt3sas: if fault is observed during driver load time then issue diag reset to recover HBA from fault state.(SCGCQ02131954)
- Add Citrix Hypervisor 8.0 driver binary support in Ph12.(SCGCQ02122776)
-Allow Encapsulated NVMe commands through IOCTL for NVMe device which has blocked access status.(SCGCQ02048934)
- mpt3sas: Add driver support for MEMORY MOVE Tool box command issued from application.(SCGCQ02082549)
-Revert (ER SCGCQ01992112 => Enable drivers internal lookup table to track scsi cmd).(SCGCQ02085401)
-Port Upstream fix: Fix kernel panic during expander reset (Fix for scsi_host_find_tag() returning invalid address).(SCGCQ02085406)
-SAS35 Ph11 -Update to MPI 2.6.8 specification and 2.00.54 header files.(SCGCQ02080516)
-Enumerating SES for a managed switch from new PCIe Device type "MPI26_PCIE_DEVINFO_SCSI.(SCGCQ02080567)
- Linux IT Ph12 mpt3sas: Disable high IOPs mode on non-Intel architectures.(SCGCQ02082547)
-Phase 12: Add SLES12SP5 OS Support.(DCSG00056539)
-mpt3sas: fix double-fetch bug in _ctl_ioctl_main().(DCSG00012734)
-Upstream: Port support target smid for [abort|query] task.(DCSG00013488)
-Upstream: clean up a couple sizeof() uses.(DCSG00013979)
-Add RHEL 7.7 GA OS Support.(DCSG00015325)
-Phase 13 SLES 15 SP1: Driver rpm package naming convention is changed..(DCSG00005502)
-Unifying Host Trace Buffer handling between Linux and Windows Driver.(DCSG00002773)
-mpt3sas: port upstream patch - drivers: Remove explicit invocations of mmiowb().(DCSG00005411)
-Check in MPI 2.6 2.6.9 Headers.(DCSG00005425)
-mpt3sas: Add managed IRQ's support on kernel greater than v5.0.(DCSG00002614)
-mpt3sas: Remove CPU architecture check to decide performance mode.(DCSG00002648)
-mpt3sas: Enable msix_load_balance only when when combined reply queue mode is disabled(DCSG00002721)
-SLES12SP5 PRE GA OS Support through Source RPM.(DCSG00002775)
-mpt3sas: make driver module parameters visible in sysfs(DCSG00003965)
version 30.00.00.00 -- Moderate Impact/Low Probability of Occurrence
-----------------------
Linux driver-PH11
defects
- Uninstallation of mpt3sas rpm on Citrix6.0 fails with error message "No module mpt3sas found"(SCGCQ00342761)
- Device may not be properly offlined or unblocked in some scenarios.(SCGCQ00347498)
- Running processes are not getting resumed post hibernation(SCGCQ00395183)
- Driver does not load with Invader C0 with DDR enabled and Host Credits set to 30,000.(SCGCQ00395447)
- Setting a default value for max_msix_vectors(SCGCQ00448248)
- Linux mpt3sas: Installation of mpt3sas driver rpm fails on OEL7.1 OS(SCGCQ00846206)
- Linux mpt3sas: Fix wrong size of argument being passed, which is identified by Coverity tool(SCGCQ00881680)
- Linux Combined src: Observed compilation errors on RHEL5 and SLES10 kernels(SCGCQ00917411)
- Observing Protection fault due to sas device list corruption(SCGCQ00933587)
- System crashes while unloading and loading driver with NVMe drive attached(SCGCQ01098644)
- Block and unblock messages are not observed when NVMe drive is removed(SCGCQ01124682)
- FW Faulted with fault code 0x5861 while running IOs with NVMe Encapsulated Messages(SCGCQ01206566)
- Marlin B0: OS crashed while running Diag reset with IOs(SCGCQ01311474)
- Buildkit is modified to install Out of box rpm also in '/lib/modules/4.4.0+2/updates' and also RPM naming convention has been changed to match the inbox driver naming convention.(SCGCQ01318375)
- Disable ASPM for MPI2 controllers(SCGCQ01329184)
- RHEL 6.8 32 Bit is hitting kernel panic after loading Phase5.0 PA-3 Driver for IT Ventura Controller.(SCGCQ01418569)
- Update code to free intended memory pool.(SCGCQ01488145)
- Memory leak when unloading driver with NVMe flashed SAS35 controller in the system(SCGCQ01497725)
- Memory leak, after cable pull and push of SAS/SATA drives with DMD setSCGCQ01509274)
- When the volume members are hot removed and added while performing diag reset, the phy disks are not discovered.(SCGCQ00344824)
- The RHEL5, RHEL6 and SLES11 OS rpms in FIXID package do not comply to the naming standard(SCGCQ00477885)
- Kernel Panic seen while booting the system with blank card.(SCGCQ00574258)
- Driver initialization fails after some random iterations of load/unload of mpt3sas driver module(SCGCQ00589083)
- Mpt3sas driver initialization fails on Citrix XenServer(SCGCQ00676273)
- Linux mpt3sas SRIOV: SATA devices are not visible on the VMs when the base machine OS is RHEL5.x(SCGCQ00730461)
- SMP IRQ affinity per CPU is not added on few supported kernels(SCGCQ00731242)
- TRI_MODE definition should be removed from mpi header(SCGCQ00834585)
- Linux mpt3sas: Fix array compared against '0',which is identified by Coverity tool(SCGCQ00881517)
- Linux mpt3sas: Fix Resource leak identified by Coverity tool(SCGCQ00881682)
- Linux SAS3: Unable to boot into Fedora22 OS when connected the OS drive behind HBA after installing the driver rpm(SCGCQ00886999)
- Initial Ref Tag is incorrect with 4K sector size drives when PI is enabled for (>=3.18 kernels(SCGCQ01015654)
- Code Review Defect: The NVMe native PRP construction uses wrong address in couple of places and that needs to be fixed.(SCGCQ01079119)
- Linux Ventura IT phase2: Unable to achieve product targets performance numbers with SAS devices(SCGCQ01175998)
- Linux SAS35 mpt3sas: Driver load with less HBA queue size while doing multiple driver unload and load operations(SCGCQ01213150)
- Print message of driver for Active cable power management, prints incomplete for RHEL6.x(SCGCQ01255499)
- call-trace observed on RHEL6.x while unloading driver.(SCGCQ01336601)
- Ph4 IT Linux mpt3sas: Observing kernel panic during topology configuration w/ blk-mq enabled(SCGCQ01351060)
- Ventura Phase5: OS crash while removing the drives connected to the controller(SCGCQ01386942)
- Linux IT SAS3.5 Phase5 mpt3sas: Observing MCE errors while upgrading the Firmware(SCGCQ01440053)
- Workaround in driver to post 64bit request descriptor to register at offset 0xC0/0xC4 to avoid hitting HW bug(SCGCQ01514520)
- Fix, False timeout prints for ioctl and other internal commands during controller reset.(SCGCQ01555936)
- Linux IT Ph9 mpt3sas: Fix Unknown symbol __umoddi3 dependency error while loading the driver(SCGCQ01869644)
- Device is Offlined during Disable/Enable of Inter-Expander Phys(SCGCQ00323892)
- Linux mpt3sas: port enable is failed during mpt3sas driver loaded with module parameter max_msix_vectors set to 1(SCGCQ00485663)
- In certain cases when max_msix_vectors was to set to 8, it is printing -1(SCGCQ00500728)
- Synchronization between PF and VF host drivers is missing while performing diag reset operation(SCGCQ00682671)
- Port enable event timeout is observed on VF drivers(SCGCQ00711051)
- Linux mpt3sas: Kernel Panic while creating filesystem on a drive(SCGCQ00731042)
- SAS3.5 Phase 2 Linux Driver : IOs terminate with Ref Tag and Guard errors on NvMe drives .(SCGCQ01206759)
- Ensure the connector_name string is NUL-terminated for NVMe devices(SCGCQ01225123)
- Linux IT SAS35 Phase3: Firmware Fault 0x5862 seen after connecting drives to Cutlass A1 card(SCGCQ01273339)
- Code Review defect: Don't send sync cache and SSU to FW, when pci_error_recovery or adapter_over_temp is set(SCGCQ01341910)
- use scsi_internal_device_block_nowait for RHEL distros greater than RHEL7.3(SCGCQ01526190)
- Phase 9: Marking transport command as completed though the command is in use.(SCGCQ01829803)
- Phase9 Linux Driver:- Include RHEL 7.6 & SLES12SP4 binaries to "28.00.01.00-1"(SCGCQ02035467)
- RAID Volume drives have FPE disabled after a Diag Reset.(SCGCQ00330248)
- Driver initialization fails after some random iterations of driver load & unload(SCGCQ00551238)
- MPI specs mentions Slot field of SAS DVC pg0 is not valid when EnclosureHandle field is zero which is not taken care in code(SCGCQ00588226)
- INVALID_STATE ioc status is not handled properly on VFs for SAS IO UNIT Control message.(SCGCQ00701320)
- Linux mpt3sas SRIOV: IO''s terminated and 0x2667 fault is observed on VFs while performing diag reset on PF.(SCGCQ00718817)
- Linux mpt3sas SRIOV: kernel panic observed while running TMs from VFs(SCGCQ00729497)
- Linux mpt3sas: PFA LED was still glowing on Enclosure even when SMART error SATA drive is replaced with good SATA drive(SCGCQ00806442)
- Linux mpt3sas: Fix Unused pointer value defect identified by Coverity tool(SCGCQ00881681)
- Linux Driver: Sles 11 SP4 beta Driver rpm file names are in wrong format(SCGCQ00888840)
- Linux Driver: Partial driver message is displayed when active cable power consumption exception occurs(SCGCQ01025061)
- Coverity Linux_mpt3sas Ph2: Missing break in switch((SCGCQ01215510)
- Coverity Linux_mpt3sas Ph2: Nesting level does not match indentationSCGCQ01215516)
- Coverity Linux_mpt3sas Ph2: Wrong size of argument being passed as parameter to function (SCGCQ01215534)
- Coverity Linux_mpt3sas Ph2: Logically dead code(SCGCQ01216306)
- NVMe devices are not visible to user on Big endian systems.(SCGCQ01249933)
- Unmap DMA mappings done while building PCIE native SGL(NVMe PRP(SCGCQ01254375)
- Linux IT mpt3sas: Fix the defects opened in CC reviews #13767 & #13774 related Dual Path topology support(SCGCQ01266371)
- mpt3sas: Avoid sleeping in interrupt context(SCGCQ01329329)
- Linux IT sas35 Phase5 mpt3sas: FW events sent before diagnostic reset are not getting cleaned up during reset(SCGCQ01397582)
- Ventura: As per MPI spec use Supplemental Reply Post Host Index Register(combined reply queue(SCGCQ01629402)
- Default value is not set for prot_capabilities when negative value is given for prot_mask parameter(SCGCQ00485251)
- Blocked Devices are made offlined if diag reset is issued at time of unblocking the device.(SCGCQ00493093)
- When device unblocked in certain cases, no messages are not seen in the logs regarding device unblock(SCGCQ00664470)
- When IOC goes bad, while flushing the IOs, protection info SGLs are not released for DIF IOs.(SCGCQ00664893)
- Linux mpt3sas SRIOV: SRIOV support is not enabled on Fedora OS kernels(SCGCQ00736946)
- Linux mpt3sas: XenServer 5.5 binaries are missing in the release tar ball(SCGCQ00802063)
- Linux mpt3sas: Fix dereference NULL return value defect identified by Coverity tool(SCGCQ00881498)
- Linux mpt3sas: Fix Uninitialized scalar variable defect identified by Coverity tool(SCGCQ00881684)
- Linux mpt3sas: CPU affinity hint is un-uniformly enabled in case if the number of CPUs are more than MSI-X vectors enabled(SCGCQ00903484)
- Asynchronous completion of timedout IO and task abort of timedout IO.(SCGCQ01027851)
- Coverity Linux_mpt3sas Ph2: Wrong size of argument being passed as parameter to function(SCGCQ01222482)
- Driver fails to load post installation.(SCGCQ01458946)
- Fix Timeout value and Reset method used for Target Reset issued on internal command Timeout. (Code Review fix)(SCGCQ01473759)
- Linux mpt3sas: System hang when a drive is removed from JBOD on sles11sp3 OS(SCGCQ00426108)
- Loading mpt3sas driver hangs on few kernels because of memory alloc failure.(SCGCQ00518874)
- End device location is not displayed few times when internal commands fail during device discovery.(SCGCQ00595788)
- Kernel panic while issuing LUN reset or target reset during running IOs(SCGCQ00655811)
- Remove extra lock being acquired and add RHEL 6.2+ support for host_lockless mode(SCGCQ00682882)
- Linux mpt3sas: Wrong description was displayed on the dpkg -l command output on Debian OS's(SCGCQ00828818)
- Linux mpt3sas: Fix unchecked return value defect identified by Coverity tool(SCGCQ00881685)
- As per MPI26 spec each reply queue set must have 16 reply queues with same upper 32bits of their memory address(SCGCQ01272382)
- Updated OEL6_UEK and OEL7_UEK buildkit(SCGCQ01436811)
- Controller fault state 265d while loading latest merged driver for SAS2 card(SCGCQ01471650)
- Remove logically dead code(SCGCQ01488142)
- OS crashes when drives are hot plugged while loading driver(SCGCQ01494556)
- Fix compilation error for SLES11(SCGCQ01698115)
- Driver compilation fails on latest upstream kernel(>= v4.17(SCGCQ01799543)
- Driver goes in infinite retry loop if internally generated REPORT LUN command response jammed with Check condition(SCGCQ00319620)
- Reply post queue depth calculation is not as per the MPI2.5 spec.(SCGCQ00322490)
- Infinite loops can occur if MPI2_IOCSTATUS_CONFIG_INVALID_PAGE is not returned(SCGCQ00347491)
- kernel panic during module load followed by Enclosure removal.(SCGCQ00384772)
- Updated SAS3 README.pdf(SCGCQ00434818)
- Kernel Panic is seen when issued Diag reset from task management(SCGCQ00654562)
- Set the module param allow_drive_spindown to default if invalid values are passed.(SCGCQ00711793)
- Linux mpt3sas: Driver rpm for OEL5.11 UEK kernel is not generated in the 7.255.04.00 alpha build.(SCGCQ00783341)
- Linux Ventura IT Phase2 : Observing Data Corruption which chaos tool on NVMe drives(SCGCQ01187754)
- Linux SAS35 Phase2: Allocate PCIe SGL pool only for SAS35 HBA devices(SCGCQ01204019)
- Linux SAS35 IT Ph2: SATA drive will be in blocked state if diag reset occurs while any ATA Passthrough command is outstanding▪(SCGCQ01221454)
- Upstream mpt3sas: fix hang on ata passthru commands(SCGCQ01255965)
- Fixed - Sync cache command failure with hostbyte=DID_NO_CONNECT during driver unload.(SCGCQ01291425)
- Driver has to use sense buffer to copy error response for NVMe encapsulated IOCTL commands.(SCGCQ01391926)
- Memory leak seen after using storcli and unloading the driver(SCGCQ01479414)
- NVMe task management command is not executed as per NVDAT settings(SCGCQ01524245)
- SAS3 PH2 Linux: In dkms installation mode the driver loading is not successful on RHEL 5.8 32 bit(SCGCQ00314484)
- OVM 3.2.1 OS kernel fails to allocate the memory requested for higher queue depth(SCGCQ00518928)
- Used GFP_KERNEL flag instead of GFP_ATOMIC flag while allocating memory for event notification reply data structure at ISR level(SCGCQ00552999)
- Linux mpt3sas: Don't block the drive when drive is under device addition process at SML(SCGCQ00846228)
- Refcount fw_events and fix unsafe list usage(SCGCQ00933591)
- Linux IT SAS3.5 ph3 mpt3sas: Target number for vSES is incremented after host reset(SCGCQ01255996)
- Fix for file system going to read-only mode when controller is resetted(SCGCQ01315476)
- Fix SAS drives going for Spin Down when module param allow_drive_spindown is set to 3(SCGCQ01337377)
- Driver Unload command does not exit when connected drives are disconnected while unloading driver(SCGCQ01403879)
- wrong sizeof argument being passed to sizeof( ▪ (SCGCQ01484567)
- Code refactor: memory allocation,setting status for incorrect command,accesing dev struct after decrementing its ref count.(SCGCQ01558459)
- The log_info constant is supposed to be IOP_LOGINFO_CODE_TASK_TERMINATED rather than the non-sensical 0x1CA86D0(SCGCQ00301838 port of )
- writeq changed back to 64bit pci transfers(SCGCQ00301840 port of SCGCQ00259827)
- Staged Device Discovery functionality of driver not working(SCGCQ00305273 port of SCGCQ00282024)
- Coexistence of GEN 2 and GEN 3 driver conflicts on OVM 3.0.3(SCGCQ00335262 port of SCGCQ00330431)
- Coexistence of GEN 2 and GEN 3 driver conflicts on OVM 3.0.3(SCGCQ00340303 port of SCGCQ00330431)
- Add support for configurable Chain Frame Size.(SCGCQ00933600 port of SCGCQ00929253)
- Remove unnecessary synchronize_irq(SCGCQ01079113 port of SCGCQ01077560)
- Message displayed improperly in var log(device_block failed with return(27(SCGCQ01099928 port of SCGCQ01096464)
- Replace #if defined preprocessor used for "ktime_to_ms" function with Kernel version, where "ktime_to_ms" func is defined(SCGCQ01105904 port of SCGCQ01100154)
- device_remove_in_progress check is not implemented in IOCTL path(SCGCQ01105910 port of SCGCQ01079361)
- Linux mpt3sas: Set sas_phy's negotiated_linkrate sysfs attribute to 12Gbps if corresponding device is 12Gbps device(SCGCQ01105911 port of SCGCQ01100134)
- Upstream mpt3sas - Fix warnings exposed by W=1(SCGCQ01179535 port of SCGCQ01154412)
- Linux IT Ph14 mpt3sas: Observed kernel panic while performing shutdown operation followed by immediate PCI device hotplug(SCGCQ01380972 port of SCGCQ01348068)
- Port Upstream fix: Fix kernel panic during expander reset (Fix for scsi_host_find_tag(SCGCQ02116554 port of SCGCQ02085406)
- When staged discovery is enabled, post diag reset, devices get added, removed and then again added with new target ids.(SCGCQ00301851 port of SCGCQ00288449)
- ASD diaganostic trigger support fake event needs to change(SCGCQ00301855 port of SCGCQ00269303)
- missing delay not getting set during system bootup(SCGCQ00324675 port of SCGCQ00314867)
- LSI SAS HBA 6Gb adapters fails Read Capacity 16 command sent to Tape drive(SCGCQ00341420 port of SCGCQ00295267)
- Add support for OEL 6.4.(SCGCQ00454977 port of SCGCQ00411878)
- device_blocked, handle(0x0027(SCGCQ00571402 port of SCGCQ00481285)
- Drives attached to the expander are not discovered(SCGCQ00571418 port of SCGCQ00567801)
- Add branding string support for OEM custom HBA's(SCGCQ00637547 port of SCGCQ00566744)
- Fixed the defect by adding a check for other LUNS even if LUN0 is offline(SCGCQ00703194 port of SCGCQ00664374)
- Driver compiles on 4.4 kernel with no errors(SCGCQ01073774 port of SCGCQ01066197)
- Remove usage of 'struct timeval'(SCGCQ01079115 port of SCGCQ01078582)
- Upstream mpt3sas - Eliminate conditional locking in mpt3sas_scsih_issue_tm((SCGCQ01179583 port of SCGCQ01154336)
- Addition of two events to Active Cable Exception Event Data(SCGCQ01185776 port of SCGCQ01181276)
- Upstream scsi: rename SCSI_MAX_{SG, SG_CHAIN}_SEGMENTS and "DEFINE_PCI_DEVICE_TABLE" macro is deprecated.(SCGCQ01203757 port of SCGCQ01198899)
- Linux IT Ph14 mpt3sas: Observed kernel panic during HBA hot plug operation just before issuing system shutdown operation(SCGCQ01380973 port of SCGCQ01366025)
- Linux IT Ph14 mpt3sas: Poweroff command fails to shutdown the host post surprise removal of controller(SCGCQ01380975 port of SCGCQ01352902)
- Linux IT phase7 mpt3sas: Increase the IOCTL timeout to support the IOCTL commands having timeout >= 512 seconde(SCGCQ01868047 port of SCGCQ01867387)
- Red Hat 6.3 support(SCGCQ00361916 port of SCGCQ00297615)
- Added support to issue a Start Stop Unit command (stopping the target(SCGCQ00423262 port of SCGCQ00394200)
- Unbalanced reply queue to CPU mapping when max_msix_vectors is set(SCGCQ00448247 port of SCGCQ00448225)
- Target Reset Fails during the disk addition(SCGCQ00481890 port of SCGCQ00481268)
- Drive is not showing up in the OS after powering on with 9207-8e with Bobcat Expander(SCGCQ00487138 port of SCGCQ00419910)
- Component drives of a Volume goes missing once the volume is deleted(SCGCQ00487140 port of SCGCQ00468602)
- Linux mpt3sas: Observed kernel panic during driver load time on RHEL5.11 OS(SCGCQ00880259 port of SCGCQ00878516)
- Can't get 1MB IO size using mpt2sas driver on OEL UEK or UEK2(SCGCQ00898466 port of SCGCQ00530826)
- OS not discovering all drives in dual node configuration(SCGCQ01026842 port of SCGCQ00776162)
- Update Initial Ref Tag with correct value for 4K PI drives (kernels < 3.18 (SCGCQ01073780 port of SCGCQ01066189)
- Don't overreach ioc->reply_post[] during initialization , which results in "slab-out-of-bounds" dump on final iteration.(SCGCQ01079114 port of SCGCQ01077566)
- Avoid mpt3sas_transport_port_add NULL parent_dev(SCGCQ01110265 port of SCGCQ01109669)
- Linux : Enclosure Handles are not updated for SAS device during diag reset(SCGCQ01372661 port of SCGCQ01326058)
- Linux IT Ph14 mpt3sas: Added Hot-Plug Surprise removal support on IOCs(SCGCQ01383826 port of SCGCQ01341334)
- mpt3sas: Disable DIX support by default.(SCGCQ01465762 port of SCGCQ01465665)
- Turning-off Log_info available bit in ioc_status for mpi_trigger(SCGCQ00301847 port of SCGCQ00279997)
- Fixid Packaging doesn't contain the RPM for SLES10/SLES11(SCGCQ00361981 port of SCGCQ00356161)
- Driver does not comply with the updated timing requirements for issuing a Hard Reset.(SCGCQ00361982 port of SCGCQ00316021)
- Intelligent Cluster: Linux Kernel Panic on SLES 11.2 with 9201-16e(SCGCQ00376665 port of SCGCQ00356062)
- _base_get_ioc_facts: failed going to ready state (ioc_state=0x20000000(SCGCQ00571424 port of SCGCQ00568563)
- Fix driver compilation errors on RHEL5 kernels.(SCGCQ01080913 port of SCGCQ01074408)
- Increase NVMe device queue depth to remove performance bottleneck in the driver(SCGCQ01316459 port of SCGCQ01305414)
- Linux IT SAS3.5 Ph7 mpt3sas: Support for Kernel 4.15 via DDA PT mode(SCGCQ01884875 port of SCGCQ01875700)
- Add Diagnostic Trigger management and new DiagService Event to Linux Driver(SCGCQ00301829 port of SCGCQ00226997)
- Verifying the proper memory allocation for "ioc->chain_lookup" in the function _base_allocate_memory_pools(SCGCQ00301835 port of SCGCQ00249415)
- move the scsi_host_put to the right place(SCGCQ00301844 port of SCGCQ00271607)
- Diag Service: No triggers events fired for every reboot of system with Co-Existance of CCOH and DaigService(SCGCQ00301846 port of SCGCQ00257763)
- Added support for fedora17(SCGCQ00361920 port of SCGCQ00251438)
- Added support for CentOS 6.3(SCGCQ00361921 port of SCGCQ00251425)
- Update the usage of the function pci_remove_bus_device(SCGCQ00394683 port of SCGCQ00359149)
- SLES 11 SP3 Beta4 Support(SCGCQ00420593 port of SCGCQ00408139)
- When a device is in a non-operational state wait for EEH recovery completion before removing the dead IOC function(SCGCQ00425367 port of SCGCQ00399592)
- Drive Pull/Insert Issue - START_UNIT timeouts(SCGCQ00483262 port of SCGCQ00481271)
- Kernel panic while upgrading the firmware online(SCGCQ00550047 port of SCGCQ00526468)
- Host need to complete SCSI command with DID_RESET status instead of DID_SOFT_ERROR under certain conditions.(SCGCQ00694147 port of SCGCQ00693983)
- In DIF-TYPE1-IP mode, the APP tag is zero'd on the wire.(SCGCQ00695354 port of SCGCQ00691983)
- Linux mpt3sas: Modified the OEM's HBA product name(SCGCQ00788347 port of SCGCQ00787798)
- Unable to disable a phy by setting corresponding phy's 'enable' sysfs attribute to zero(SCGCQ00845286 port of SCGCQ00842931)
- Linux mpt3sas: Don't block the Enclosure device(SCGCQ00898464 port of SCGCQ00896193)
- Synchronize timed-out IO and Task Management functions(such as task_abort & target_reset(SCGCQ01073779 port of SCGCQ01066194)
- set num_phys after allocating phy[] space (SCGCQ01110264 port of SCGCQ01109662)
- Upstream mpt3sas - Ensure the connector_name string is NUL-terminated(SCGCQ01185771 port of SCGCQ01154419)
- Set maximum transfer length per IO to 4MB for VDs(SCGCQ01210393 port of SCGCQ01072631)
- DIF Patchs from Oracle(SCGCQ00301830 port of SCGCQ00255629)
- Possible deadlock in IOCTL path(SCGCQ00301842 port of SCGCQ00266321)
- smp_processor_id(SCGCQ00301843 port of SCGCQ00268580)
- Update the usage of the function scsi_internal_device_unblock(SCGCQ00331941 port of SCGCQ00331929)
- Create phase 13 GCA generic point release for OEL UEK R2(SCGCQ00395417 port of SCGCQ00258229)
- Driver is using device handle instead of enclosure slot method for clearing of PFA status(SCGCQ00435927 port of SCGCQ00435028)
- Linux mpt2sas: Process works from firmware work-queue sequentially(SCGCQ00772791 port of SCGCQ00769798)
- Linux mpt2sas: Driver initialization hangs when pci_enable_msix API fails to enable MSIX vector(SCGCQ00773759 port of SCGCQ00760760)
-(SCGCQ00933617 port of SCGCQ00926726)
- Upstream mpt3sas - Don't spam logs if logging level is 0(SCGCQ01194636 port of SCGCQ01155651)
- Ph14 Linux Driver : Active Cable Exception events are logged by driver for attachment of Passive cables.(SCGCQ01210253 port of SCGCQ01205383)
- Linux IT Ph14: Enable Active Cable Exception Event for Fury/Invader(SCGCQ01237382 port of SCGCQ01237340)
- Linux SAS35 Ph3 : By default disable multipath support for SAS3.5 HBA's too.(SCGCQ01316220 port of SCGCQ01301732)
- Not able to update manpage 11 when try to update FW from OS.(SCGCQ01729592 port of SCGCQ01639219)
- 2012 source code copyright(SCGCQ00301826 port of SCGCQ00254805)
- when async scanning mode is enabled and scanning is in progress devices are removed and their transport layer entries are not removed.(SCGCQ00380178 port of SCGCQ00379998)
- Clear PFA Status on SGPIO when PFA Drive is Removed or Replaced.(SCGCQ00423261 port of SCGCQ00392963)
- Linux mpt2sas: A new driver module Parameter is added to Enable/Disable EEDP Support(SCGCQ00423263 port of SCGCQ00295288)
- Updated the set_affinity.sh to have a support for more than 32 CPU cores systems(SCGCQ00438827 port of SCGCQ00427368)
- Update the usage of the function scsi_internal_device_unblock((SCGCQ00462789 port of SCGCQ00461953)
- failure at _transport_set_identify and mpt2sas_transport_port_add(SCGCQ00571398 port of SCGCQ00497017)
- Add branding string support for OEM custom HBA's(SCGCQ00871877 port of SCGCQ00867336)
- Remove SRIOV specific code from mpt3sas driver and update buildkits accordingly.(SCGCQ01203756 port of SCGCQ01197731)
- RHEL7.x: Crash occurred while loading mpt3sas driver with module parameter smp_affinity_enable set to 0(SCGCQ01504666 port of SCGCQ01496368)
- Driver sets queue_depth=254(SAS_QUEUE_DEPTH(SCGCQ01763013 port of SCGCQ01741671)
- driver oops associated with the max_queue_depth command line option set too small(SCGCQ00301837 port of SCGCQ00258989)
- Providing a negative value to sdev_queue_depth parameter leads to incorrect queue depth for a SAS drive.(SCGCQ00301848 port of SCGCQ00279155)
- Linux driver : updated initrd.img doesn't contain newly installed mpt2sas driver module(SCGCQ00332653 port of SCGCQ00332288)
- Debian6.0.5 Linux Support for 32 and 64 bit(SCGCQ00361923 port of SCGCQ00251412)
- Add support for OEL 6.3.(SCGCQ00361926 port of SCGCQ00303161)
- Oracle Linux 5.9 Support(SCGCQ00454974 port of SCGCQ00401299)
- Linux mpt2sas: Added support for OVM3.2.1 OS(SCGCQ00454976 port of SCGCQ00411913)
- Kernel Panic observed after issuing controller diag reset.(SCGCQ00526798 port of SCGCQ00501333)
- Only 8 MSIX vectors are enabled for SAS3 HBAs on a 32 core machine(SCGCQ01107215 port of SCGCQ01106942)
- Missing curly braces on if statement to print message when there is insufficient power for active cable.(SCGCQ01110263 port of SCGCQ01109643)
- Upstream mpt3sas - Eliminate dead sleep_flag code.(SCGCQ01179606 port of SCGCQ01154385)
- DID_SOFT_ERROR issue encountered on SATA RAID1 during testing 12.100.00.00(SCGCQ01284610 port of SCGCQ01284381)
- Linux mpt3sas: Enumeration of drives for OEM specific controller(SCGCQ01408565 port of SCGCQ01318421)
- IO Timeouts observed while running IO and parallel TaskMgmt test with SATA drives(SCGCQ01522289 port of SCGCQ01497972)
- mpt3sas: Lock access to the HBA's PCI config space from user space while Diag reset operation is going on(SCGCQ01827523 port of SCGCQ01819327)
EnhancementRequests
- Change Diagnostic Toolbox CLI SGL format to IEEE (to match MPI 2.5.1 spec change(SCGCQ00314987)
- Added mpt3sas driver support for fedora18 OS(SCGCQ00442462)
- Added code to display Location of End Device.(SCGCQ00452326)
- Added UEK3 (v3.8.13-16)(SCGCQ00552232)
- Oracle Linux 5.10 Support(SCGCQ00552253)
- Added mpt3sas driver support for Citrix 6.2 OS(SCGCQ00552276)
- Added CENTOS7.0 (x86_64(SCGCQ00675458)
- Updating the device removal handshake protocol only on VF drivers(SCGCQ00696568)
- Add branding string support for OEM custom HBA's(SCGCQ00718659)
- Update upstream Linux mpt3sas: [PATCH] block: Kill bio_segments(SCGCQ00778584)
- Update upstream Linux mpt3sas: [PATCH] [SCSI] mpt3sas: remove unused variables(SCGCQ00778631)
- Linux mpt3sas: Add branding string support for OEM custom HBA's(SCGCQ00793599)
- Linux combined src: Disable temperature fault functionality for SAS2 HBA's(SCGCQ00915064)
- Linux SAS3.5 phase2 IT: Added support for UNMAP commands for NVMe drives via fast-path(SCGCQ01190581)
- Merge MPI end point linux driver to Phase3 sas35 mainline and later to upstrea(SCGCQ01224602)
- Pre-allocate RDPQ Array at driver boot time(SCGCQ01297392)
- Driver support for OEL 7.4_UEK (4.1.12-94.3.9.el7uek(SCGCQ01396745)
- OS driver support for Oracle Linux 7.5 - SAS3 PH 16, SAS3.5 Ph 8(SCGCQ01586104)
- Call t10_pi_ref_tag for RHEL 8 kernels(SCGCQ02069530)
- Test Unit Ready retries causes slow discovery(SCGCQ00406610)
- Added RHEL5.10 support(SCGCQ00442446)
- Added mpt3sas driver support for Centos 6.5 OS(SCGCQ00571454)
- Addnew module parameter to allow /disallow host driver to issue SCSI commands to bring up drive.(SCGCQ00609923)
- Added support for OVM 3.3.1(SCGCQ00666996)
- Linux mpt3sas: Porting upstream patches to mainline(SCGCQ00825572)
- Fedora 22 OS Support is added(SCGCQ00846536)
- Linux mpt3sas_Phase 10 PA#1: Dropping support for RHEL5 and SLES10 distro and Unified binary support for RHEL,OEL & CentOS.(SCGCQ00864228)
- Linux combined src: Added mpt2sas driver definitions to combined driver src(SCGCQ00914998)
- MPI header update with new supported controller addition(SCGCQ01064186)
- Interim Experimental Change: Add code to detect Non first page unaligned SGE for NVMe drives and panic.(SCGCQ01080920)
- 0001 - mpt3sas: set default value for cb_idx(SCGCQ01300828)
- 0006 - mpt3sas: always use first reserved smid for ioctl passthrough and second reserved smid for internal scsi io commands(SCGCQ01300840)
- Report Package Version from HBA Driver(SCGCQ01445879)
- Skip pending I/Os issued to NVMe drives while processing Broadcast Async Event(SCGCQ01558613)
- mpt3sas: Do not wait for IOC to become operational if HBA is unplugged(SCGCQ01681422)
- OS driver support for XenServer7.4 SAS3 PH 16, SAS3.5 Ph 8(SCGCQ01750033)
- Linux IT Ph9 mpt3sas: Added mpt3sas driver support for SLES15 OS(SCGCQ01828337)
- mpt3sas: Ph9 - Add OEL 6.10 support(SCGCQ01870215)
- Modified the SAS3 Linux Driver such that the SAS2 and SAS3 drivers can co-exist.(SCGCQ00300298)
- Added Red Hat 5.9 support(SCGCQ00377019)
- Added mpt3sas driver support for Citrix 6.1 OS(SCGCQ00442454)
- Add support to MPI - ReplyDescriptorPostQueueArray defined in IOC Init Request Message(SCGCQ00467389)
- Add branding string support for Intel custom HBA's(SCGCQ00546703)
- Added SLES12 RC3 support ( only x86_64)(SCGCQ00672325)
- Provide an option to enable / disable spin down SSD and HDD devices while unloading driver.(SCGCQ00695289)
- Linux mpt3sas: Add branding string support for OEM custom HBA's(SCGCQ00780483)
- Added SLES12 GM Support (only X86_64(SCGCQ00785459)
- Linux mpt3sas: Make use of additional HighPriorityCredit number of message frames for sending SCSI IO's(SCGCQ00899842)
- Linux combined src: Don't print Enclosure level and connector name information for SAS2 HBA's(SCGCQ00915060)
- Linux combined src: Disable mapping of SAS devices to VFs SRIOV feature for SAS2 HBA's(SCGCQ00915109)
- Linux combined src: Retain same module parameters names which were their before for mpt2sas driver(SCGCQ00916328)
- Linux IT/IR: Merge mpt2sas driver in to mpt3sas driver module.(SCGCQ00955258)
- Linux SAS3.5 IT: Limit 0x2100 FW fault by updating host index up on reaching the thresh hold value(SCGCQ01149963)
- Linux SAS3.5 IT Ph2: Block the drive after recieving any ATA pass-though command for that driver and unblock it after completion of the command(SCGCQ01218960)
- 0007 - mpt3sas: lockless command submission(SCGCQ01300843)
- 0009 - mpt3sas: Enable tag support for all supported kernels (SCGCQ01300853)
- Upstream mpt3sas: Fix memory allocation failure test in 'mpt3sas_base_attach(SCGCQ01454958)
- Upstream mpt3sas: scsi_transport_sas: switch to bsg-lib for SMP passthrough(SCGCQ01606945)
- Upstream mpt3sas: Fix function prototypes for module_param_call(SCGCQ01607482)
- Added support for Atlas Gen4 PCIe switches in MPT driver environments for Linux.(SCGCQ01731329)
- Upstream: Added an i/o barrier(SCGCQ01828734)
- Updated the build kits to support SAS2 Phase 14 level(SCGCQ00300292)
- Added SLES11 SP3 OS support(SCGCQ00454992)
- Add support to log message when Temperature Threshold exceeds for any Sensor.(SCGCQ00604649)
- Performance improvement by changing Affinity change and adding Host lock less mode(SCGCQ00610127)
- Add branding string support for custom HBA's(SCGCQ00636608)
- Added RHEL7.0 support(SCGCQ00672310)
- Added OEL7.0 Support(SCGCQ00673317)
- Linux mpt3sas: Detect the SMART Error SATA drive in the Topology and turn on it's corresponding PFA LED(SCGCQ00791340)
- Added SLES11sp4 GM Support(SCGCQ00826215)
- Added UEK3 Update5 (v3.8.13-68(SCGCQ00826232)
- Adding Intruder specific code to the Gen3 Linux Phase 9 driver(SCGCQ00831649)
- Debian 8.0 OS support-SAS3 Phase 10(SCGCQ00856661)
- Linux combined src: For an IO, build MPI SGL LIST for SAS2 HBA's and build IEEE SGL LIST for SAS3 HBA's(SCGCQ00915044)
- Linux combined src: Don't send PHYDISK_HIDDEN Raid Action request on SAS2 HBA's(SCGCQ00915050)
- Linux combined src: Disable DIX feature specific code for SAS2 HBA's(SCGCQ00915061)
- Linux combined src: Disable Target mode hooks from combined driver src(SCGCQ00915067)
- Prevent sending I/Os with NVMe PRP if non first page unaligned SGE is detected(SCGCQ01080930)
- Linux SAS3.5 Ph2: Enable DIX support(SCGCQ01200312)
- Linux SAS3.5 IT Ph2: Set NVMe device queue properties in such a way to reduce holes in sges(SCGCQ01224810)
- Added support for XenServer 7.1.(SCGCQ01289850)
- 0005 - mpt3sas: Introduce mpt3sas_get_st_from_smid(SCGCQ01300838)
- 0008 - mpt3sas: create separate lookup table for NVMe PRP list(SCGCQ01300851)
- Optimize I/O memory consumption in driver(SCGCQ01388190)
- Enhanced handling of DMA allocation, If the allocation does not fit within same 4GB(SCGCQ01388961)
- Upstream mpt3sas: Create two versions of scsi_internal_device_unblock((SCGCQ01447644)
- Upstream mpt3sas: fix format overflow warning(SCGCQ01454955)
- Added support for RHEL7.5 GA (3.10.0-862.el7(SCGCQ01719072)
- Linux IT Phase9 mpt3sas: Ignore processing of Phy having target not responding reason code while processing re-queued event(SCGCQ01892634)
- Linux IT Phase9 mpt3sas: Enable PCIe switch enumeration by default for all kernel versions(SCGCQ02018676)
- Added DIX support of the Linux operating system to the driver.(SCGCQ00262891)
- Add 96 MSI-X vector support for Invader C0(SCGCQ00371782)
- Added mpt3sas driver support for fedora19 OS(SCGCQ00552267)
- Added UEK3 Update3 (v3.8.13-44(SCGCQ00675434)
- Target Numbers of mapped drives on VFs won't increase after diag reset on PF (SCGCQ00689554)
- Update Attribution Language - Copyright, Trademark, Confidentiality to Avago(SCGCQ00729462)
- Linux combined src: Defined 'hba_mpi_version_belonged' IOC variable to differnate the each gerenation HBA's specific functionalities(SCGCQ00915025)
- Linux combined src: Remove SCSI_MPT3SAS_LOGGING entry from Kconfig files ▪ (SCGCQ00915035)
- RHEL 7.3 OS Support for SAS3.5 Phase 2(SCGCQ01218181)
- Added mpt3sas driver support for OEL6.9(SCGCQ01289003)
- 0003 - mpt3sas: separate out _base_recovery_check(SCGCQ01300833)
- Reducing the number of times enclosure config page read request sent by driver(SCGCQ01357382)
- Increase event log buffer to support 24 port HBA's to avoid buffer overflow.(SCGCQ01368517)
- NVMe Task Management - Controller Reset Support (SCS(SCGCQ01445901)
- Upstream: mpt3sas: clarify mmio pointer types (Fix compiler warning(SCGCQ01686081)
- Phase8: Fix sparse warnings of inhouse mpt3sas driver.(SCGCQ01729697)
- SAS3.5 Phase9: Intel Spectre Vulnerability - Add support for retpoline in driver RPM and DUD for RHEL, SLES and OEL(SCGCQ01828339)
- Upstream: Fix _transport_smp_handler(SCGCQ01828766)
- Use t10_pi_ref_tag and compatible _transport_smp_handler API in SLES15SP1(SCGCQ02070829)
- Added mpt3sas driver support for RHEL 6.5 OS(SCGCQ00552245)
- Added OEL6.5 Support(SCGCQ00552260)
- Added UEK3 U1 (v3.8.13-26(SCGCQ00571510)
- Added SRIOV support for both Xen and KVM hypervisor.(SCGCQ00627105)
- Added UEK3 Update2 (v3.8.13-35(SCGCQ00654016)
- Added RHEL 6.6 Support(SCGCQ00675448)
- Remove kernel support older than N-3 kernel updates, where N is latest kernel update release.(SCGCQ00696790)
- Updated MPI 2.5 Release: MPI 2.5 Rev K (2.5.6(SCGCQ00709717)
- Added Oracle Linux 5.11 Support(SCGCQ00775653)
- Update upstream Linux mpt3sas: [PATCH] mpt3sas: Use pci_enable_msix_exact(SCGCQ00776753)
- Update upstream Linux mpt3sas: [PATCH] block: Convert bio_for_each_segment(SCGCQ00778582)
- Added UEK3 Update4 (v3.8.13-55(SCGCQ00788014)
- Linux mpt3sas: Add branding string support for OEM custom HBA's.(SCGCQ00793614)
- Linux SAS3: Add RHEL 6.7 GA Support(SCGCQ00848126)
- Linux combined src: Manage MSI-X vectors according to HBA device type(SCGCQ00915056)
- Linux combined src: Add OEM's SAS2 HBA's PnP ID Branding names(SCGCQ00915065)
- Active cable exception handling in mpt3sas driver:(SCGCQ01008402)
- Ventura IT Linux Driver: Update MPI 2.6.07 specification, and 2.00.45 header files(SCGCQ01133212)
- Reduce memory footrpints in kdump kernel.(SCGCQ01237163)
- 0004- mpt3sas: open code _scsih_scsi_lookup_get(SCGCQ01300836)
- Added mpt3sas driver support for RHEL6.9 (SCGCQ01316324)
- Added support for SAS Device Discovery Error Event.(SCGCQ01354911)
- Upstream mpt3sas: Split scsi_internal_device_block(SCGCQ01447640)
- mpt3sas: Added new thread called hot plugged watchdog which will poll for whether HBA device is unplugged or not(SCGCQ01681425)
- Linux Drivers: MPI2.5 Update Rev U (2.0.26(SCGCQ00304398)
- Added Debian7.0 Linux OS Support(SCGCQ00552280)
- Added mpt3sas driver support for fedora20(SCGCQ00571464)
- Updated MPI 2.5 Release: MPI 2.5 Rev J (2.5.5(SCGCQ00653281)
- Added OEL6.6 Support(SCGCQ00721141)
- Added RHEL5.11 Support(SCGCQ00775576)
- Update upstream Linux mpt3sas: [PATCH] mpt3sas: delay scsi_add_host call to work with scsi-mq(SCGCQ00778620)
- Linux mpt3sas: Added mpt3sas driver support for RHEL7.1 OS(SCGCQ00787975)
- Linux Mpt3sas SRIOV: Use serial number as primary key to uniquely identify the SATA drives in device persistence mapping mode(SCGCQ00813146)
- Linux mpt3sas: Added mpt3sas driver support for OEL7.1 OS (SCGCQ00838951)
- Ph 11 LINUX_MPT3SAS : Dropping support for few distros as per MR OS_Support matrix.(SCGCQ00900247)
- Linux conbined src: Move Gen3 HBA's device registration with PCI, SML and IOCTL API's to separate mpt3sas_module.c file(SCGCQ00915016)
- Linux Combined src: Added csmi hooks and it will be enabled only for SAS2 HBA's(SCGCQ00915063)
- SLES 12 SP2 OS Support for SAS3.5 Phase 2(SCGCQ01154063)
- Linux Ventura Phase2: Add support for IO Unit Control, Shutdown message(SCGCQ01165691)
- Linux SAS35 IT: Added driver support for Dual/multi-path typologies(SCGCQ01237381)
- 00010 - mpt3sas: allocate as many chains as needed and remove chain list maintenance overhead(SCGCQ01300854)
- Ph5 : SLES12 SP3(4.4.73-5(SCGCQ01396754)
- Linux IT Phase9 mpt3sas: Enable irq poll in Linux driver to avoid CPU hard and soft lockups(SCGCQ01571359)
- mpt3sas: code refactor - move section of code which waits for IOC to be in operational state into a separate function(SCGCQ01681420)
- Linux IT Phase9 mpt3sas: Added driver support for Ambrosia NVMe Switch Adapter(SCGCQ01891714)
- Added Red Hat 6.4 support(SCGCQ00376609)
- Added mpt3sas driver support for Centos 6.4 OS(SCGCQ00552285)
- When the IOC over heats, driver needs to flush the IOs and panic.(SCGCQ00654911)
- When memory allocation for SCSI command message frame request tracker queue fails, driver should be capable lowering the queue depth and allocate memory.(SCGCQ00693434)
- VF drivers doesn't need to retrieve the BIOS pages(SCGCQ00698258)
- 3008 IT: Add OEM String to Driver for OEM Board Design(SCGCQ00860516)
- Linux mpt3sas: Include changes of MPI 2.5 Rev M and MPI 2.6 Rev E specifications and 2.00.39 headers(SCGCQ00899809)
- Linux combined src: Disabled SATA SMART polling feature for SAS2 HBA's(SCGCQ00915058)
- Linux combined src: Ported WarpDrive HBA support from mpt2sas driver src(SCGCQ00922147)
- Linux Combined src: Ported fix for setpci reset kernel oops from mpt2sas src(SCGCQ00922149)
- OEL 7.3 OS Support for SAS3.5 Phase 2(SCGCQ01154077)
- Linux IT mpt3sas: Recognize and act on IO's iopriority info(SCGCQ01237164)
- 0002 - mpt3sas: use list_splice_init(SCGCQ01300832)
- Upstream mpt3sas: switch to pci_alloc_irq_vectors(SCGCQ01367469)
- Upstream mpt3sas: fix dma_addr_t casts(SCGCQ01541636)
- Added support for XenServer 7.3 OS.(SCGCQ01554011)
- Upstream mpt3sas: Do not mark fw_event workqueue as WQ_MEM_RECLAIM.(SCGCQ01686075)
- mpt3sas: wait for and flush running commands on shutdown/unload (Upstream Patch(SCGCQ01686096)
- Change attribution language from Avago to Broadcom and update copyright end year(SCGCQ01757358)
- Upstream: Introduced struct "mpt3sas_nvme_cmd"(SCGCQ01828741)
- Add RHEL 8 OS driver support(SCGCQ02136688)
version 28.00.03.00 -- Moderate Impact/Low Probability of Occurrence
-----------------------
Linux driver-PH9
defects:
- Driver load fails on big endian systems (SPARC64).(SCGCQ01836661)
- Linux IT Ph9 mpt3sas: Fix Unknown symbol __umoddi3 dependency error while loading the driver(SCGCQ01869644)
- Phase 9: Marking transport command as completed though the command is in use.(SCGCQ01829803)
- Phase9 Linux Driver:- Include RHEL 7.6 & SLES12SP4 binaries to "28.00.01.00-1".(SCGCQ02035467)
- Linux IT phase7 mpt3sas: Increase the IOCTL timeout to support the IOCTL commands having timeout >= 512 seconds(SCGCQ01868047 port of SCGCQ01867387)
- Intel Spectre Vulnerability - Add support for retpoline in driver RPM and DUD for RHEL, SLES and OEL(SCGCQ01856662 port of SCGCQ01784898)
- Linux IT phase7 mpt3sas: Increase the IOCTL timeout to support the IOCTL commands having timeout
>= 512 seconds(SCGCQ01868049 port of SCGCQ01867387)
- mpt3sas: Lock access to the HBA's PCI config space from user space while Diag reset operation is
going on(SCGCQ01905582 port of SCGCQ01819327)
- Linux IT SAS3.5 mpt3sas: Observed hard lockups with SAS35 card which are configured with 16 MSI-x
vectors on > 16 logical CPU machine(SCGCQ01906874 port of SCGCQ01473904)
- Linux IT SAS3.5 Ph7 mpt3sas: Support for Kernel 4.15 via DDA PT mode(SCGCQ01905585 port of SCGCQ01875700)
- mpt3sas: Lock access to the HBA's PCI config space from user space while Diag reset operation is
going on(SCGCQ01827523 port of SCGCQ01819327)
- Linux IT SAS3.5 Ph7 mpt3sas: Support for Kernel 4.15 via DDA PT mode(SCGCQ01884875 port of SCGCQ01875700)
- Port Upstream fix: Fix kernel panic during expander reset (Fix for scsi_host_find_tag() returning invalid
address)(SCGCQ02116554 port of SCGCQ02085406)
EnhancementRequest:
- Added support for Atlas Gen4 PCIe switches in MPT driver environments for Linux..(SCGCQ01731329)
- Upstream: Added an i/o barrier.(SCGCQ01828734)
- SAS3.5 Phase9: Intel Spectre Vulnerability - Add support for retpoline in driver RPM and DUD.()
for RHEL, SLES and OEL.(SCGCQ01828339)
- Upstream: Fix _transport_smp_handler() error path.(SCGCQ01828766)
- Upstream: Introduced struct "mpt3sas_nvme_cmd".(SCGCQ01828741)
- Linux IT Ph9 mpt3sas: Added mpt3sas driver support for SLES15 OS.(SCGCQ01828337)
- Linux IT Phase9 mpt3sas: Enable irq poll in Linux driver to avoid CPU hard and soft lockups.(SCGCQ01571359)
- mpt3sas: Ph9 - Add OEL 6.10 support.(SCGCQ01870215)
- Linux IT Phase9 mpt3sas: Ignore processing of Phy having target not responding reason code.()
while processing re-queued event.(SCGCQ01892634)
- Linux IT Phase9 mpt3sas: Added driver support for Ambrosia NVMe Switch Adapter.(SCGCQ01891714)
- Linux IT Phase9 mpt3sas: Enable PCIe switch enumeration by default for all kernel versions.(SCGCQ02018676)
- Call t10_pi_ref_tag for RHEL 8 kernels.(SCGCQ02069530)
- Use t10_pi_ref_tag and compatible _transport_smp_handler API in SLES15SP1.(SCGCQ02070829)
version 27.125.01.00-1 -- Moderate Impact/Low Probability of Occurrence
-----------------------
IR/IT (MPT3) – Ph 16 (new)
Defects
- Driver load fails on big endian systems (SPARC64).(SCGCQ01836661)
- Fix, False timeout prints for ioctl and other internal commands during controller reset.(SCGCQ01555936)
- Ventura: As per MPI spec use Supplemental Reply Post Host Index Register(combined reply queue) when MSI-X vectors > 16.(SCGCQ01629402)
- Fix compilation error for SLES11.(SCGCQ01698115)
- Driver compilation fails on latest upstream kernel(>= v4.17), due to changes in "queue_flag_set_unlocked" API.(SCGCQ01799543)
- Code refactor: memory allocation,setting status for incorrect command,accesing dev struct after decrementing its ref count.(SCGCQ01558459)
- Linux IT SAS3.5 mpt3sas: Observed hard lockups with SAS35 card which are configured with 16 MSI-x vectors on > 16 logical CPU machine.(SCGCQ01615533 port of SCGCQ01473904)
- Intel Spectre Vulnerability - Add support for retpoline in driver RPM and DUD for RHEL, SLES and OEL.(SCGCQ01856662 port of SCGCQ01784898)
- Driver sets queue_depth=254(SAS_QUEUE_DEPTH) and reports tagged(1) when both CMDQUE and BQUE bits set to zero for SES devices.(SCGCQ01789379 port of SCGCQ01741671)
- Not able to update manpage 11 when try to update FW from OS.(SCGCQ01789377 port of SCGCQ01639219)
- Linux IT phase7 mpt3sas: Increase the IOCTL timeout to support the IOCTL commands having timeout >= 512 seconds.(SCGCQ01868049 port of SCGCQ01867387)
- mpt3sas: Lock access to the HBA's PCI config space from user space while Diag reset operation is going on.(SCGCQ01905582 port of SCGCQ01819327)
- Not able to update manpage 11 when try to update FW from OS.(SCGCQ01729592 port of SCGCQ01639219)
- Driver sets queue_depth=254(SAS_QUEUE_DEPTH) and reports tagged(1) when both CMDQUE and BQUE bits set to zero for SES devices.(SCGCQ01763013 port of SCGCQ01741671)
- Linux IT SAS3.5 Ph7 mpt3sas: Support for Kernel 4.15 via DDA PT mode.(SCGCQ01905585 port of SCGCQ01875700)
- Linux IT SAS3.5 mpt3sas: Observed hard lockups with SAS35 card which are configured with 16 MSI-x vectors on > 16 logical CPU machine.(SCGCQ01906874 port of SCGCQ01473904)
EnhancementRequests:
- OS driver support for Oracle Linux 7.5 - SAS3 PH 16, SAS3.5 Ph 8.(SCGCQ01586104)
- Added support for RHEL6.10 GA(2.6.32-754.el6).(SCGCQ01828835)
- Skip pending I/Os issued to NVMe drives while processing Broadcast Async Event.(SCGCQ01558613)
- mpt3sas: Do not wait for IOC to become operational if HBA is unplugged.(SCGCQ01681422)
- OS driver support for XenServer7.4 SAS3 PH 16, SAS3.5 Ph 8.(SCGCQ01750033)
- Upstream mpt3sas: scsi_transport_sas: switch to bsg-lib for SMP passthrough.(SCGCQ01606945)
- Upstream mpt3sas: Fix function prototypes for module_param_call(SCGCQ01607482)
- Added support for RHEL7.5 GA (3.10.0-862.el7).(SCGCQ01719072)
- Intel Spectre Vulnerability - Add support for retpoline in driver RPM and DUD for RHEL, SLES and OEL.(SCGCQ01784898)
- Upstream: mpt3sas: clarify mmio pointer types (Fix compiler warning).(SCGCQ01686081)
- Phase8: Fix sparse warnings of inhouse mpt3sas driver.(SCGCQ01729697)
- Added support for RHEL7.5 GA (3.10.0-862.el7).(SCGCQ01749948)
- mpt3sas: Added new thread called hot plugged watchdog which will poll for whether HBA device is unplugged or not.(SCGCQ01681425)
- mpt3sas: code refactor - move section of code which waits for IOC to be in operational state into a separate function.(SCGCQ01681420)
- Linux IT Ph6 mpt3sas: Added mpt3sas driver support for SLES15 OS.(SCGCQ01839348)
- Upstream mpt3sas: fix dma_addr_t casts.(SCGCQ01541636)
- Added support for XenServer 7.3 OS.(SCGCQ01554011)
- Upstream mpt3sas: Do not mark fw_event workqueue as WQ_MEM_RECLAIM.(SCGCQ01686075)
- mpt3sas: wait for and flush running commands on shutdown/unload (Upstream Patch).(SCGCQ01686096)
- Change attribution language from Avago to Broadcom and update copyright end year.(SCGCQ01757358)
version 25.125.03.00 -- Moderate Impact/Low Probability of Occurrence
----------------------
initial release
EnhancementRequests (4)
- Added support for RHEL6.10 GA(2.6.32-754.el6).(SCGCQ01828835)
- Intel Spectre Vulnerability - Add support for retpoline in driver RPM and DUD for RHEL, SLES and OEL.(SCGCQ01784898)
- Added support for RHEL7.5 GA (3.10.0-862.el7).(SCGCQ01749948)
- Linux IT Ph6 mpt3sas: Added mpt3sas driver support for SLES15 OS.(SCGCQ01839348)
- Driver sets queue_depth=254(SAS_QUEUE_DEPTH) and reports tagged(1) when both CMDQUE and BQUE bits set to zero for SES devices.(SCGCQ01789379 port of SCGCQ01741671)
- Not able to update manpage 11 when try to update FW from OS.(SCGCQ01789377 port of SCGCQ01639219)
Lenovo StorCLI Storage Host-Bus-Adapter (HBA) Linux Utility
StorCLI (Command Line) Utility for Storage Management
Adapters Supported:
ThinkSystem RAID 530-8i PCIe 12Gb Adapter (7Y37A01082)
ThinkSystem RAID 530-4i Flex Adapter (7M17A03932)
ThinkSystem RAID 530-4i Flex Adapter (7M27A03918)
ThinkSystem RAID 530-8i Dense Adapter (SD530 RAID)
ThinkSystem RAID 530-16i PCIe 12Gb Adapter (4Y37A09727)
ThinkSystem RAID 540-8i PCIe Gen4 12Gb Adapterr (4Y37A78834)
ThinkSystem RAID 540-16i PCIe Gen4 12Gb Adapter (4Y37A78835)
ThinkSystem RAID 730-8i 1GB Cache PCIe 12Gb Adapter (7Y37A01083)
ThinkSystem RAID 730-8i 2GB Flash PCIe 12Gb Adapter (4Y37A09722)
ThinkSystem RAID 930-8i 2GB Flash PCIe 12Gb Adapter (7Y37A01084)
ThinkSystem RAID 930-16i 4GB Flash PCIe 12Gb Adapter (7Y37A01085)
ThinkSystem RAID 930-24i 4GB Flash PCIe 12Gb Adapter (7Y37A01086)
ThinkSystem RAID 930-8e 4GB Flash PCIe 12Gb Adapter (7Y37A01087)
ThinkSystem RAID 930-4i 2GB Flash Flex Adapter (7M17A03933)
ThinkSystem RAID 930-4i 2GB Flash Flex Adapter (7M27A03917)
ThinkSystem RAID 930-16i 8GB Flash PCIe 12Gb Adapter(4Y37A09721)
ServeRAID M1210 SAS/SATA Controller (00JY194)
ServeRAID M1215 SAS/SATA Controller (46C9114)
LSI SAS3004 RAID (NA-SAS3004-B)
LSI SAS3004 RAID (NA-SAS3004-N)
ServeRAID M5210 SAS/SATA Controller (46C9110)
ServeRAID M5225-2GB SAS/SATA Controller(00AE938)
ServeRAID M5215 with 2GB Flash Enablement Flex System x240 M5 (00JX142)
ServeRAID M5210e SAS/SATA Controller (46C9117CTO)
ServeRAID M5120 SAS/SATA Controller (81Y4478)
IBM Flex System Storage Expansion Node (68Y8588)
ServeRAID M5115 SAS/SATA Controller for Flex System (90Y4390)
ServeRAID M5100 Series IBM Flex System Flash Kit for X6 (44T1178)
ThinkSystem RAID 940-8i 4GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09728
ThinkSystem RAID 940-8i 8GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09729
ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09730
ThinkSystem RAID 940-32i 8GB Flash PCIe Gen4 12Gb Adapter for 4Y37A09733
ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Internal Adapter for 4Y37A09735
NOTE TO SERVICE - Reference RETAIN #N/A
007.2705.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.27
Defects:
Support for 16MB flash in storclif (DCSG01555459
SPDM invalidate on a slot with certificate is deleted/cleared does not return proper failure message (DCSG01200711
In "OTC" command output "phy info" "sasaddress" and vendor name is missing. (DCSG01416857
OTC command not displaying the Version header info when there is a partial failure (DCSG01453843
phyinfo legends are missing in ./storcli /c0/pall show command only for controller (DCSG01464352
autoconfig lowlatency change option is not working (DCSG01225927
Fixing storcli leaks (DCSG01436087
Storclif set clockmode does not return any message in either profile 30 or 32 (DCSG01343704
Storcli download command needs update. (DCSG01385977
Error message and Ctrl_prop needs update (DCSG01366236
Negative value is shown (DCSG01452047
CLI crashes when setting timestamp on all the enclosures (DCSG01275981
Show Drive Smart Info Failed without any error message (DCSG01453497
Fixing storcli leaks and unitialised variables (DCSG01528847
Schema validation fails with Drive details with (DCSG01312383
Removed switch and NVMe fields as part of the phy all show information (DCSG01429974
OTC command out of 2 coredump files only one coredump file is created. (DCSG01430008
Storcli fails to set "Preboottrace" to OFF. (DCSG01407684
Ph27_Storecli:pcie phy information should be displayed in the "storcli64.exe /c0/lnall show" command output. (DCSG01430854
show events command is missing in IT help command list (DCSG01440137
storcli /pall show command fails with "Unable to retrieve PcieIoUnitPage0 information" when executed on HBA (DCSG01451391
set sasadd command runs successfully on Megaraid controller. (DCSG01451336
storcli log file ballooning in size when used as a compare file for controller properties (DCSG01440265
Failure Description for lnx commands in profile 32 not consistent (DCSG01327288
Storcli lists incorrect parameter options (DCSG01480789
New PSOC related properties are not being displayed (DCSG01214343
Storcli legends for "CertProv" is missing in 'storcli show" output (DCSG01230074
OTC command status is shown as failure even after collecting the data (DCSG01462898
As part of phy compare linkspeed command invalid description observed. (DCSG01463047
storcli to allow both del and delete keywords (DCSG01333727
StorcliF and Storcli64 command details are incorrect. (DCSG01431031
Storclif did not show correct 24G drive speed as 22.5Gb/s (DCSG01436600
storcli exits when chunksize is given as 0 (DCSG01441105
StorCLI Add help page for storcli64 /cx/ex set time command (DCSG01266055
StorCLI IT show vpd command gives Json error (DCSG01428172
Help indentation update (DCSG01303723
No reason for the failure during "Alarm: On/off/silence" (DCSG01451915
Multiple drive microcode updates fail if mode is not provided by user. (DCSG01509349
addvirtualdriveeachr0 creates R0 virtualdrive for incorrect drive format. (DCSG01445078
logfile command not working in EFI (DCSG01440821
drive fw download with incorrect fw detailed status not seen and success status message noted (DCSG01192976
Expander firmware download command is getting success without firmware file (DCSG01368730
In "vmware_esxi_8" readme "./storcli64 /c0 set refclk =0" command is missing in "StorCLI command to ESXCLI plugin mapping". (DCSG01446616
StorCLI phy -events commands (DCSG01452698
Fixing BD HUB reported license issues (DCSG01235456
otc command output some configuration pages are missing. (DCSG01417587
Incorrect details listed during V_D expansion. (DCSG01447578
Disabling PCIe lane is reporting failed/Invalid arguments (DCSG01334639
StorCLI crashes with /pall phyevents in Windows ARM (DCSG01462894
Expander firmware download is failing on enclosure behind IT using storcli (DCSG01360586
get otc command is failing in Linux when multiple coredump is present (DCSG01437688
scrutiny vib file version name noted wrong (DCSG01456900
VD creation is successful with PD in JBOD state (DCSG01186039
set time not listed in IT help / schema mapping list gives success message (DCSG01455624
Storcli set vpd command does not return any result, either pass or fail (DCSG01441368
volume table is not listed in sorted order for "cx show all " command (DCSG01187424
Heading of SAS and IOC pages in otc command are displayed wrong and Size in DB Register (DCSG01417593
Storcli fails with segmentation fault while query for enclosure and drive (DCSG01277632
Storcli shows no failure Description for "restart" operation. (DCSG01303781
refclk " command is missing in "StorCLI command to ESXCLI plugin mapping". (DCSG01456786
Storcli does not have ESXi 8.x binary release and ESXi 6.x support mentioned in Readme. (DCSG01361836
'esxcli storcli controller get snapdump ' fails with syntax error (DCSG01464430
Storcli shows wrong information in DG details when JBOD/System is present (DCSG01521782
EFI StorcliO VPD update/flash fails (DCSG01559387
Changing of reset phy eveent commands to phy errorlogs (DCSG01448647
Lane information does not have the legends in the output (DCSG01445839
Description for PSOC flash from storcli is not proper when "resetnow" is used (DCSG01221186
There is no error message for lane show info command for lane number 16. (DCSG01446504
Return value for setting of large CCDelay does not match (DCSG01442317
issues with Consistency check delay and schema (DCSG01542373
StorCLI diag cmd returns successfully on M.2 Ctrl, even the Ctrl Firmware show not supported on iMR (DCSG01444219
Storcli needs update in error message and in detailed description. (DCSG01525040
observing "File read error !!!" while downloading enclosure firmware in UEFI shell (DCSG01521747
EGS: Storcli -Next Learn time in /cx show all differs with actual /Cv show time (DCSG01180101
Show drive command status shows failure with description "Show drive information failed", however show all status shows success with description "Show drive info (DCSG01462887
Storcli does not list proper "required" fields while creating V D using "addvdcachecade" option. (DCSG01453731
Storcli crashes during "debug level" set. (DCSG01361819
One of the element status displayed wrongly with extended status command (DCSG01372738
For the PI drives storcli64 shows PI as 'No' whereas LSA shows PI as capable (DCSG01395078
displaying proper description while setting invalid refclk. (DCSG01356146
Json schema support for StorCLI phy show command (DCSG01428869
Storcli shows output for invalid Lane. (DCSG01409017
Storcli "Enclosure" set time command needs update (DCSG01408981
All db commands are failing once after unregister the trace buffer. (DCSG01444766
Storcli returns missing char invalidate cmd output (DCSG01376779
Storcli shows duplicate information in readme files. (DCSG01323236
storcli phyevets is showing succss while executing on Mega RAID Controller (DCSG01464454
Storcli exits without returning anything on trying to set aso key with characters more than 127 (DCSG01409627
BGOP'S operations error message is inconsistent (DCSG01230073
Delete error-counters is not actually clearing the error counters (DCSG01416763
In windows OTC command output "capturing log serial number for the RTT Trace Buffer.." displays wrong. (DCSG01444337
Error message noted wrong with mode f command (DCSG01377687
Storcli shows success instead of failure for "show expansion" operation (DCSG01481384
Sending wrong image to controller has different message (DCSG01524642
output is jumbled for the eghs command output (DCSG01440963
Plugin for "start/stop/resume/pause" for consistency check and patrolread does not work. (DCSG01451161
Unable to set DS options. (DCSG01380122
In "vmware_esxi_8" readme "./storcli64 /c0/pall show phyevents " command is missing in "StorCLI command to ESXCLI plugin mapping". (DCSG01462816
Transform iMR command is mapped to incorrect esxcli command (DCSG01453766
otc commnad output "phy_info" data phy no 3 enable bit shows "N" Enbl bit instead of "y" in compare "storcli64.exe /c0/pall show" command . (DCSG01430015
Spaces are important (DCSG01303433
Lane information legends are missing in ./storcli /c0/lnall show command only for controller (DCSG01464343
For IT controller storcli "show eventloginfo" command output "status" and "description" displays wrong. (DCSG01448384
Using latest storecli "set refClk" command fail with error message. (DCSG01368858
Storcli Virtual drive creation should fail with "reusetargetid" parameter. (DCSG01430905
While executing "get otc" command there is no "storcli" version number displayed. (DCSG01437154
system time sync'up fails for expander with storcli command (DCSG01271785
PSOC hardware version is not displayed in storcli output. (DCSG01317465 (Port Of Defect DCSG01325851)
While executing Enclosure Status cli displays wrong values. (DCSG01528830 (Port Of Defect DCSG01531725)
storcli in Linux occasionally causing coredumpctl (DCSG01489233 (Port Of Defect DCSG01552077)
autoconfig lowlatency change option is not working (DCSG01225927 (Port Of Defect DCSG01228069)
Not able to get snapdump with -s=all option (DCSG01447404 (Port Of Defect DCSG01447574)
Created 100 MB virtual drive with 1024K strip size on 4K sector size target device but the created size is 96MB (DCSG01320102 (Port Of Defect DCSG01329183)
Using cachevd option returns that volum creation fails, but the volume is actually created (DCSG01432157 (Port Of Defect DCSG01432522)
Storcli commands shows "Not enough memory to continue." with a page option. (DCSG01255030 (Port Of Defect DCSG01267413)
Unable to create R0 V D's using "addvdeachr0" (DCSG01450023 (Port Of Defect DCSG01453727)
VD creation is successful with PD in JBOD state (DCSG01186039 (Port Of Defect DCSG01187950)
Physical drives count mismatch is there if compared with the actual drives present when tape drive is connected (DCSG01491544 (Port Of Defect DCSG01493435)
Storcli crashes while Upgrading PSOC image for IT card (DCSG01446520 (Port Of Defect DCSG01490408)
Set linkspeed operation asks for system reboot when the operation fails. (DCSG01554840 (Port Of Defect DCSG01557410)
VD table is not listed in sorted order for "cx show all " command (DCSG01187424 (Port Of Defect DCSG01187947)
In set security command help, file=filename is shown, but does not seem to work. (DCSG01432351 (Port Of Defect DCSG01437189)
Multiple Cli2 observations w.r.t command returning success for incorrect syntax, blank Volum size etc. (DCSG01466254 (Port Of Defect DCSG01466530)
EnhancementRequests:
Enhancing the enclosure download command to read chunk size as input (DCSG01191253
Storcli Support for UBM6 backplane (DCSG01238774
Support for PsoC catalog version checking on update. (DCSG01245656
Create security lock key using EKMS (DCSG01311276
Port of ScrutinyCLI commands to StorCLI (DCSG01415106
Add PERST control for NVMe drives (DCSG01400121
Prevent installation of inappropriate Firmware image (DCSG01421212
VMware ESXi 8.0 OS Support Tool chain migration (DCSG01176442
Allow CLI to run on perc branded cards (DCSG01219438
add PERST control mechanism for NVMe Physical Disks (DCSG01421205
Implement REFCLK control in storcli (DCSG01291369
Security Version Support on 96xx boards (DCSG01174566
Remove the check for heterogenous config and allow the user to change the link config irrespective of homogenous or heterogenous. (DCSG01171914
Add a new StorCLI command to "show all" faster (DCSG01303802
Need 95xx boards to perform equally or better than Invader when only slower RAID volumes comprised of SATA HDDs are attached. (DCSG01272082
SecureBoot: FW download operation fails with incorrect message (DCSG01132479
Time-sync between Host-Utilities and all the Expanders in the topology (DCSG01214261
95xx HBA controllers Support for multiple PSOC images (DCSG01203368
Remove PERST support from refclock commands for IT cards (DCSG01388007
Handling MPI blocked functions. (DCSG01373043
Port of ScrutinyCLI commands to StorCLI (DCSG01390110
Removing "PSOC Version" field from the controller detailed command (DCSG01270804
Support Drive drive image without using Host Memory (DCSG01454023
Allow reusing of TargetIDs without 120 seconds delay(DCSG01394604)
VMware ESXi 8.0 OS Support (DCSG01258042
OS_Utils: The 'Device Speed' is shown as 24.0Gb/s for SAS4 drives (DCSG01388208
De-branding of OEM name from StorCLI (DCSG01312376
ESXCLI Plugin support with DSDK migration (DCSG01431017
Displaying PackageVersion for Aero-IT Images (DCSG01191525
Storcli: Implement REFCLK control (DCSG01232268
Hide nonvolatile key option in for temporary key option (DCSG01325680 (Port Of EnhancementRequest DCSG01328968)
ESXCLI Plugin support with DSDK migration (DCSG01475599 (Port Of EnhancementRequest DCSG01483012)
SAS-4 JBOD integration with RAID controllers (Harpoon) (DCSG01364599 (Port Of EnhancementRequest DCSG01373126)
Move from 7.22 to 7.24 channel base for the R2 program (DCSG01345495 (Port Of EnhancementRequest DCSG01352227)
OEM requesting FIPS support on Linux (DCSG01315666 (Port Of EnhancementRequest DCSG01507167)
CLI to display the energypack serialNo content in decimal format (5 digits including leading zero) for Supercap (DCSG01452070 (Port Of EnhancementRequest DCSG01455486)
Add a new StorCLI command to "show all" faster (DCSG01303802 (Port Of EnhancementRequest DCSG01453526)
- (DCSG01064409 (Port Of EnhancementRequest DCSG01085133)
007.2206.0000.0000- Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.20
Defects:
-Storcli : Copyright shows as year 2021 instead of 2022 & also build release year 2021 instead of 2022 & also build release year shows as 2021 instead of 2022.(DCSG01124638)
-Error seen while flashing psoc.rom in efi CLI.(DCSG01131584)
-storcli 7.2001 does not return values for a bad drive.(DCSG01052072)
-Spellling of mismatch is displayed as "Missmatch" in "Encryption type missmatch" error message..(DCSG01091937)
-Device Type for Backplane in Alilog shown as Enclosure.(DCSG01109911)
-Storcli shows Protection Information (PI) capable drive i.e. "PI eligible" as No, however LSA shows it properly.(DCSG01145223)
-CLI not iterating through MR_SAS_CONNECTORS for H750 controllers.(DCSG01077564)
-Instance validation fails for "/c0 show all" and "controller-detailed-properties-schema.json".(DCSG01035798)
-OS drive name shown as N/A for multiple VDs.(DCSG01101813)
-Storclif reports BBU instead of cachevault for failed retention tests.(DCSG01092227)
-Storclif 7.2005 can't start retention test, says No CacheVault Found!.(DCSG01130532)
-Enclosure logical ID field is not displayed for BP connected to connected to Boca 540-16i controller.(DCSG01024654 (Port Of Defect DCSG01024693))
-Set Patrolread command hangs while setting "excludevd".(DCSG01101780 (Port Of Defect DCSG01102890))
-Strocli.efi utility got hung on issuing "storcli /c0 show" command.(DCSG01049757 (Port Of Defect DCSG01050540))
-"storcli /call show" shows jumbled drives in a Multi IT controller environment.(DCSG01040245 (Port Of Defect DCSG01040583))
-PD size displayed in Gib for some of the 4K drives is incorrect..(DCSG00389591 (Port Of Defect DCSG00994728))
-PD Firmware Release Number = N/A is displayed for drive which has valid Firmware Release Number.(DCSG01083763 (Port Of Defect DCSG01083800))
-Storcli shows success without proper description for "VD delete BBMT" command when no VD present..(DCSG01002466 (Port Of Defect DCSG01024694))
-Update splitpackage script for shenandoah.(DCSG00651204 (Port Of Defect DCSG00994744))
-While trying to import foreign config, Storcli is not showing any drive if user has "Dedicated Hotspare" & also DHS is not displaying along with VD as well.(DCSG01034883 (Port Of Defect DCSG01036901))
-While trying to import foreign config, Storcli is not showing drive as "Hotspare" if the user has only hot spares.(DCSG01028926 (Port Of Defect DCSG01029835))
EnhancementRequests:
-Update ControllerInfo Structure with PartNumber - API Changes.(DCSG01064529)
-Request for Win2022 Supportnfor their 16G Enablement launch, March 2022 RTS.(DCSG00977684)
-MegaRAID key management feature: volatile key escrow.(DCSG00992844)
-secureSignBin: implement feature to download the public key during signing or with explicit arg.(DCSG01035866)
-DCSG01082488
-API change to support PD sanitize operations enhancements.(DCSG01070995)
-Aero 9560/9580 - Add PSOC6 as Vision Controller.(DCSG01056506)
-Add control command MFI_OOB_MCTP_CONTROL_EXCEPTION_NO_CMD (0x99) in API.(DCSG01065378)
-Change the attribute name "Secured" to "Locked" in PD Properties output.(DCSG01040562 (Port Of EnhancementRequest DCSG01040785))
-Handling of VD target-ID's individually even when target-ID is assigned beyond maxLDs.(DCSG01091990 (Port Of EnhancementRequest DCSG01092477))
-Windows Client Win11 OS Support.(DCSG01043616 (Port Of EnhancementRequest DCSG01068906))
007.1907.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.19
Defects:
-While trying to import foreign config, Storcli is not showing any drive if user has "Dedicated Hotspare" & also DHS is not displaying along with VD as well.(DCSG01034883)
007.1707.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.17
Defects:
-StorCLI listing failed NVMe drives in non-sorted order.(DCSG00320844
-Instance Validation Failed for "/call/fall show all.json" and foreign-configuration-detailed-schema.json.(DCSG00408509
-MR7.16_storcli: VD creation with the remaining drives fails.(DCSG00303606
-Enclosure position is showing as - for drive detailed properties on an IT controller.(DCSG00286693
-Package Version is not displayed properly after flashing firmware..(DCSG00961822
-PH18 BETA - StorCLI - Update YEAR in the CLI banner.(DCSG00707142
-Storcli launch fails with permission denied message.(DCSG00972016
-Setting CC date and time exceeding the limit, needs to be handled.(DCSG00520110
-"rval - 0" is displayed for "show phyerrorcounters" command..(DCSG00337710
-Storcli lists "/ex show all" for "/cx show all" command..(DCSG00417504
-DiskGroup show all list Hostpare in Unconfigured drive list.(DCSG00359247
-Storcli: learnStartTime displayed incorrectly in command details.(DCSG00320649
-Storcli /cx set debug reset all help description needs an update.(DCSG00521571
-storcli /cx set flushwriteverify help needs an update.(DCSG00507067
-PH17 PA - StorCLI ARM - show file command displays incorrect output for BIOS image.(DCSG00315152
-PH18 PA - StorCLI - appropriate message needed for erase all excludemfg command.(DCSG00395234
-Storcli shows "success" with incorrect message INSTEAD of syntax error for "/c0/d1 set" command..(DCSG00543505
-storcli show alilog shows "SATA-3G" as device interface for 9361-16i.(DCSG00555672
-Handling PBLP component whild displaying Image component versions.(DCSG00301878
-MR_7.17: After Driver unload/load via DDV tools- Ctrl acces via Storcli exit with Segmentation Fault.(DCSG00426317
-coverity: fixing non-array delete and dereferencing before NULL checks.(DCSG00368376
-Handling the read-only file system from storcli.(DCSG00542683
-Updating new SPDM MPI errors.(DCSG00435039
-"Failed Drive not found" reported from enclosure level show repair command.(DCSG00423496
-Controller Lane show command is not working with individual Lanes.(DCSG00386181
-Storcli show command is not displaying remaining drives when PD info fails for one drive.(DCSG00469639
-VD creation fails from storcli even though free capacity is present in DG.(DCSG00757768
-Aero 7.15 CLI shows a extra space in the /c0 set cc h command.(DCSG00298943
-Instance Validation Failed for "/call show" and controller-properties-schema.json.(DCSG00408497
-show alilog command displays JBOD as volumes.(DCSG00556934
-Instance Validation Failed for "/call/fall import preview.json" and foreign-configuration-detailed-schema.json.(DCSG00408512
-Max commands for averaging needs to be removed from DPMstat RA output.(DCSG00286349 (Port Of Defect DCSG00306711)
-Failure observed while running set sbr command.(DCSG00779151 (Port Of Defect DCSG00932922)
-Storcli "/call/eall/sall download status" error message needs correction..(DCSG00735452 (Port Of Defect DCSG00757676)
-Unified StorCLI MR7.15 - Fixing coverity issues - Part 1.(DCSG00290662 (Port Of Defect DCSG00368612)
-Atlas 4.2: StorCLI lists wrong error message "Failed in standard Inquiry", when user tries to upgrade/downgrade all connected NVMe Drives FW at a time.(DCSG00309398 (Port Of Defect DCSG00313432)
-The foreign config of DHS/GHS details is not listing under foreign config import preview.(DCSG00919659 (Port Of Defect DCSG00935761)
-Invalid Array Size in ZB is displayed for Degraded R1 span Foreign VD in storcli foreign import preview.(DCSG00916209 (Port Of Defect DCSG00935751)
-Logical ID of Cobra expander not displayed properly in Storcli and LSA.(DCSG00342456 (Port Of Defect DCSG00391477)
-CLI crashes when issuing the phyerrorcounters command on a 14G Expander backplane.(DCSG00323054 (Port Of Defect DCSG00323721)
-Show command status not proper when issued with wrong EID.(DCSG00906544 (Port Of Defect DCSG00935762)
-Storcli shows no output for valid parameter for "/c0/p0,1,22 show" command..(DCSG00840944 (Port Of Defect DCSG00932927)
-From the CLI failed to convert UBAD state drive to UGOOD.(DCSG00391494 (Port Of Defect DCSG00391509)
-Non Foreign drives GHS are listing under Foreign import preview.(DCSG00931210 (Port Of Defect DCSG00935765)
-Storcli "show file" command does not report correct FW version.(DCSG00299788 (Port Of Defect DCSG00302030)
-Storcli show incorrect property name for "/c0/d0,3 set hidden=off" command..(DCSG00733214 (Port Of Defect DCSG00758467)
-Coverity fixing bad allocator and resource leaks.(DCSG00307346 (Port Of Defect DCSG00307355)
-Vses Device Type is displayed as Enclosure for IT card.(DCSG00920244 (Port Of Defect DCSG00935772)
-StorCLIF fail to flash firmware image of BTBL (BOOT_BLOCK) on Invader MR.(DCSG00330381 (Port Of Defect DCSG00353198)
-Storcli throws junk value is shown on set consistency check.(DCSG00906989 (Port Of Defect DCSG00935693)
-MR 7.15 StorCLI : Addressing Coverity defects.(DCSG00286677 (Port Of Defect DCSG00311222)
-CLI Version info is seen in continuation of Sense data when executed show events.(DCSG00935802 (Port Of Defect DCSG00935973)
-VDs imported from Jbod mode to RAID do not have OS name available in Linux OS.(DCSG00968023 (Port Of Defect DCSG00975216)
-CLI failing to stop a BGI or CC when paused..(DCSG00735544 (Port Of Defect DCSG00757870)
-Enclosure phyerrorcounters fails in VMware platform.(DCSG00706496 (Port Of Defect DCSG00706497)
-Storcli shows success for "set patrolread excludevd" command failure in the presence of VD..(DCSG00906735 (Port Of Defect DCSG00935770)
-For empty SPDM slots 0 & 1 show security slot info command shows as Invalid data on IT controller..(DCSG00348125 (Port Of Defect DCSG00353186)
-Segmentation fault noted with drive firmware update.(DCSG00758645 (Port Of Defect DCSG00932904)
-VD creation output shows VD size as 0KB when it reaches maximum supported virtual disks(64VDs) in a DG..(DCSG00349415 (Port Of Defect DCSG00353914)
-SAS drive Inquiry data is not shown in drive show all output.(DCSG00778367 (Port Of Defect DCSG00932917)
-Fixing Coverity defects of MR 7.15.(DCSG00299981 (Port Of Defect DCSG00309219)
-Post reboot incorrect lane speed is displayed in Storcli when user sets it to 16GT/s.(DCSG00383336 (Port Of Defect DCSG00395901)
-On storcli /c0/v1,2,3,4 del if anyone of the vd in the series is not present then all the vd's are not deleted.(DCSG00264571 (Port Of Defect DCSG00266888)
-Coverity defects - remove resource leaks, invalid types in function arguments.(DCSG00269017 (Port Of Defect DCSG00277861)
-Storcli will not show LargeIOsupport is enabled/disabled on the controller.(DCSG00353195 (Port Of Defect DCSG00353882)
-Storcli shows target id of the drive as boot drive instead of showing drive slot number for JBOD drives..(DCSG00344079 (Port Of Defect DCSG00353203)
-MR7.15_storcli: With the latest storcli, VD creation with the remaining drives fails.(DCSG00278049 (Port Of Defect DCSG00282590)
-Removed leading spaces for SATA drives.(DCSG00904104 (Port Of Defect DCSG00935692)
-Drives connected to IT controller reports Shield Counter.(DCSG00244631 (Port Of Defect DCSG00266881)
-Size of Degraded R10 Foreign VD is displayed as 0 KB in storcli.(DCSG00916207 (Port Of Defect DCSG00935746)
EnhancementRequest:
-Adding new License file and updating the build script to include the new file.(DCSG00324401
-Add CLI command to control Parity Read Cahce Bypass for SSD VDs.(DCSG00342282
-MR7.16 : Support WJ Pinning for both WB and WT Parity RAID VDs.(DCSG00214472
-Provide option in storcli to disable / enable the Preboot trace Buffer feature in MR FW..(DCSG00310366
-Enable cache retention testing on Shenandoah controllers for factory testing.(DCSG00340899
-Updating storcli code and makefiles to support VBAS builds on GCP.(DCSG00412063
-Additional NameSpace behavior changes.(DCSG00310386
-Updating storcli BST scripts to support new VBAS Auto BST procedure.(DCSG00282976
-StorCLI: Automate the test cases specific to MR7.17 Product Requirements.(DCSG00433350
-Add support for reporting SPDM Measurement Specification and Hash Algorithm.(DCSG00301782
-Updating command legends as per the command output.(DCSG00083851
-IT Drive Model Number , Revision for SATA drives displayed in full.(DCSG00371061
-MR7.16: StorCLI does not show the SAS Address of the enclosure.(DCSG00255109
-Unified StorCLI 7.17 - x64 UEFI VBAS / GCP support.(DCSG00559813
-Updating Error Strings for NVME init error codes in Apps.(DCSG00434066
-MR7.16 StorCLI: Ruby SED Support.(DCSG00264744
-CLI to handle ERROR_BUSY from Windows storport.(DCSG00348813 (Port Of EnhancementRequest DCSG00353214)
-Displaying "OS name" for VDs imported from EHBA mode to RAID.(DCSG00775114 (Port Of EnhancementRequest DCSG00932911)
-Display Enclosure serial No in Storcli.(DCSG00500922 (Port Of EnhancementRequest DCSG00932906)
-Request to add checks (DevId, SubDevice Id) check prior to flashing.(DCSG00500924 (Port Of EnhancementRequest DCSG00521828)
-SEKM Support in CLI.(DCSG00433143 (Port Of EnhancementRequest DCSG00935780)
-CLI: Package Stamping Verification During Firmware Update.(DCSG00239672 (Port Of EnhancementRequest DCSG00282815)
-StorCLI has the ability to switch the OOB mode.(DCSG00547179 (Port Of EnhancementRequest DCSG00935783)
-SMART Polling Improvement - PERC 10.(DCSG00249963 (Port Of EnhancementRequest DCSG00282814)
-PERCcli turn off logging by default.(DCSG00255367 (Port Of EnhancementRequest DCSG00282813)
-Remove the MFG date, Revision date and Rev from IT StorCLI output.(DCSG00415059 (Port Of EnhancementRequest DCSG00418372)
-Display port information for NVMe Init failed drives.(DCSG00359418 (Port Of EnhancementRequest DCSG00421187)
-storcli "set good" command can still be used for JBOD EPD-PT drives.(DCSG00318591 (Port Of EnhancementRequest DCSG00353919)
-PERC11.1 - Dual x8 Support for 16 port Controllers.(DCSG00299060 (Port Of EnhancementRequest DCSG00323772)
007.1513.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.15
Defects:
-CLI Version info is seen in continuation of Sense data when executed show events.(DCSG00935802)
-Handling the read-only file system from storcli.(DCSG00938327 (Port Of Defect DCSG00542683))
Enhancements:
-Request to add checks (DevId, SubDevice Id) check prior to flashing.(DCSG00930193 (Port Of EnhancementRequest DCSG00500924))
007.1510.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.15
Defects:
-From the CLI failed to convert UBAD state drive to UGOOD.(DCSG00391494)
-PH17 PA - StorCLI ARM - show file command displays incorrect output for BIOS image.(DCSG00320641 (Port Of Defect DCSG00315152))
-StorCLI listing failed NVMe drives in non-sorted order.(DCSG00321815 (Port Of Defect DCSG00320844)
-MR 7.16: Storcli: learnStartTime displayed incorrectly in command details.(DCSG00321908 (Port Of Defect DCSG00320649))
-rval - 0" is displayed for "show phyerrorcounters" command..(DCSG00337735 (Port Of Defect DCSG00337710))
-DiskGroup show all list Hostpare in Unconfigured drive list.(DCSG00360517 (Port Of Defect DCSG00359247))
-Controller Lane show command is not working with individual Lanes.(DCSG00386184 (Port Of Defect DCSG00386181))
-storcli /cx set flushwriteverify help needs an update.(DCSG00541982 (Port Of Defect DCSG00507067))
-"Failed Drive not found" reported from enclosure level show repair command.(DCSG00430578 (Port Of Defect DCSG00423496))
-Storcli show command is not displaying remaining drives when PD info fails for one drive.(DCSG00489855 (Port Of Defect DCSG00469639))
-Storcli /cx set debug reset all help description needs an update.(DCSG00538790 (Port Of Defect DCSG00521571))
EnhancementRequest:
-Display Enclosure serial No in Storcli.(DCSG00500922)
-IT Drive Model Number , Revision for SATA drives displayed in full.(DCSG00405900 (Port Of EnhancementRequest DCSG00371061))
007.1326.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
Defects:
-Foreign Config Preview shows empty data when Foreign config is present with Rebuild is in Progress.(DCSG00261203)
-Inconsist DG number in StorCLI.(DCSG00235157)
-RTTdump shows success but it fails to download the dump..(DCSG00253652 (Port Of Defect DCSG00253719))
-Incorrect Adapter type shown in the perccli show all output.(DCSG00241405 (Port Of Defect DCSG00244145))
-Expander firmware download using with mode 5 option fail with error message..(DCSG00239524 (Port Of Defect DCSG00240685))
-With length command, CLI says Memory Exhausted.(DCSG00235628 (Port Of Defect DCSG00236791))
-Enclosure position is showing as - for drive detailed properties on an IT controller.(DCSG00286693 (Port Of Defect DCSG00286701))
-Observe CLI Crash on windows while setting Autoconfig option.(DCSG00253642 (Port Of Defect DCSG00253722))
-MR7.15_storcli: With the latest storcli, VD creation with the remaining drives fails.(DCSG00278049 (Port Of Defect DCSG00282592))
-"No Controller found" shown when controller is busy..(DCSG00248017 (Port Of Defect DCSG00253661))
-On storcli /c0/v1,2,3,4 del if anyone of the vd in the series is not present then all the vd's are not deleted.(DCSG00264571 (Port Of Defect DCSG00266886))
-Connector Name is incorrectly displayed when connector count goes beyond 8.(DCSG00249023 (Port Of Defect DCSG00252701))
-MR 7.15: Storcli: Instance Validation Failed for "virtual-drive-config-schema.json" and "/call delete config force".(DCSG00247992 (Port Of Defect DCSG00253761))
-With new MR API changes, storcli shows failure while changing accesspolicy.(DCSG00257307 (Port Of Defect DCSG00258140))
-MR 7.15: Storcli: Instance Validation Failed for "enclosure-fw-download-schema.json" and "enclosure FW download" output..(DCSG00250066 (Port Of Defect DCSG00253733))
-Show expansion shows wrong output in presence of JBODs..(DCSG00247163 (Port Of Defect DCSG00252417))
-Enclosure position value not listed properly in show all command.(DCSG00254935 (Port Of Defect DCSG00256384))
-Drives connected to IT controller reports Shield Counter.(DCSG00244631 (Port Of Defect DCSG00266894))
-Expander firmware download help need to be corrected for IT controller..(DCSG00239870 (Port Of Defect DCSG00240680))
EnhancementRequests:
-To add return status MFI_STAT_OK_REBOOT_REQUIRED to MR_DCMD_LD_SET_PROPERTIES in mr.h.(DCSG00256271)
-Additional FDE type for Ruby SED support.(DCSG00055878)
-MFI SMP Port Num API changes.(DCSG00257777)
-MR7 API: Add package incompatibility reporting.(DCSG00231443)
-SMART Polling Improvement - API Changes.(DCSG00246317)
-Implement customSign.exe CLI wrapper utility to help customers sign with their private key.(DCSG00234646)
-Changes to support 16port connection to Expander with AeroIOC.(DCSG00254845)
-Updating storcli BST scripts to support new VBAS Auto BST procedure.(DCSG00282976 (Port Of EnhancementRequest DCSG00290359))
007.1325.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.13
Fix issue:
DCSG00235157 - Inconsist DG number in StorCLI
Description:
Customer reported the DG/Array/Row is incorrect to get from storcli and it causes "insert" command failure.
007.1324.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.13
Defects：
-Storcli: Optl not mentioned in /call/dall show output..(DCSG00065740)
-Instance Validation Failed for "/call set smartpollinterval=300" and controller-smartpollinterval-schema.(DCSG00057141)
-StorCLI crash when create VD.(DCSG00052275)
-/e: and /s: is not mentioned in the Convention for /storcli64 /c0/v0 start migrate detailed ?.(DCSG00143788)
-BZ(186687):[AMD2P & Whitley] EXSi 7 can't boot up after install storcli.(DCSG00048516)
-Storcli show Device type as backplane while no drives are connected.(DCSG00074732)
-Help Description for Migrate shows "operation" printed twice in Storcli output..(DCSG00063696)
-Instance Validation Failed for "/call show" and controller-properties-schema.json.(DCSG00057213)
-Coverity analysis - Fixing uninitialized variables, resource leaks, and return statements - Part 1.(DCSG00046195)
-Foreign topology table display BT as "Y" for drives which are in foreign state..(DCSG00068453)
-Storcli: Same help description across "/c0/e0 show" and "/c0/e0 show all"..(DCSG00064748)
-While executing perccli, by default log file with storcli.log is getting generated..(DCSG00038031)
-MR 7.13: Storcli(Regression): Syntax error seen while using "nolog" and "page" together as parameters.(DCSG00071417)
-In Aero behind atlas configuration "NVME" drive firmware revision shows wrong.(DCSG00049614)
-Storclif command for battery retention test issues command to start retention test which is an unsupported command.(DCSG00058688)
-Show DPM with type LCT is not giving proper output and register DPM commands for all OS.(DCSG00033459)
-Storcli: ProdID Legend abbreviation missing in /c0/eall show output..(DCSG00063317)
-FW sometimes allows an invalid CLI command (set personality=HBA) to be successful and sets the personality to eHBA mode.(DCSG00129542)
-Fixing Coverity defects.(DCSG00044004)
-Unable to create JBOD using the legacy command with latest Perccli.(DCSG00118670)
-MR 7.13: Storcli: GHS is shown as revertible.(DCSG00065815)
-In the presence of Locked Foreign config, "/c0/fall del" shows incorrect output..(DCSG00062615)
-StorCLI - '/c0 show nolog' reported as Un-supported Command.(DCSG00071410)
-Set VD policy to WB (unsupported )should return failure in JBOD personality..(DCSG00076992)
-Shenandoah_MRSA: Enclosure Bay count coming Wrong in CLI.(DCSG00074731)
-Shenandoah_Storcli : Legend for ID in JBOD list is missing.(DCSG00069312)
-Incorrect Legend abbreviation in storcli show output.(DCSG00058874)
-MR 7.13: Storcli: controller add commands are listed along with vx commands..(DCSG00065744)
-Even on giving wrong 'storclif delete config' command syntax, the config is cleared successfully without any error.(DCSG00055164)
-Storcli.efi shows incorrect note for unsupported commands for MR controllers.(DCSG00056335)
-VMware peccli, percli64 and storcli64 bit binary loads library from storcli 32 bit's installation path.(DCSG00074600)
-StorCLI - /c0/eall/sall start locate not working for second enclosure connected.(DCSG00040244)
-Instance Validation Failed for "/call show dpm" and controller-dpm-schema.json.(DCSG00057194)
-Command description should be modified for storclif /cx set activityforlocate=.(DCSG00069746)
-MR 7.13: Storcli: bbu not described in convention details.(DCSG00066314)
-Shenandoah_storCLI: Add vd command for r0 getting successful with 512KB when mazStripeSize is 1MB.(DCSG00057003)
-Fixing Coverity defects, uninitialized, unused variables and memory leaks.(DCSG00052049)
-Start_entry is not a command parameter in show events command.(DCSG00067937)
-On OS /cx/dall split mirror command shows success when there is no drive groups.(DCSG00069690)
-Update the storcli readme with for Esxi 6.x and Esxi 7.0 releases.(DCSG00055533)
-Extended the abbreviation in the legends.(DCSG00069703)
-Shenandoah : storcli : Energy Pack show present for MR 216i controller , where the hardware is not supported.(DCSG00053888)
-"set sbr" command mentioned in detailed help but not listed in help output..(DCSG00068444)
-Creation of VD for with more than 64 drives is failing with "Cannot create configuration with x drives".(DCSG00056544)
-Description of compare firmware ver command does not mention as IT supported command.(DCSG00070258)
-Command description should be modified for /cx set alarm command.(DCSG00069709)
-MR 7.13 : RSOD is seen for storcli.efi show command when the controller is in invalid state.(DCSG00066879)
-StorCLI /cx restart is not supported in UEFI environment should be mentioned in help..(DCSG00068879)
-Remove deprecated command 'show adpcount' from Ubuntu folder(readme).(DCSG00058329)
-Segmentation fault seen while running OCR and Patrol read in loop on ESXi7.0 OS..(DCSG00066854)
-Instance Validation Failed for "/call/fall import preview" and foreign-configuration-detailed-schema.json.(DCSG00068868)
-Field for CV is missing in table as well as in legend for storcli64.exe show command.(DCSG00067075)
-Restrict discovery of PERC HBA through StorCLI(Static binary).(DCSG00077037)
-PH14 Alpha Aero - StorCLI - Difference in output noted for /cx/px set state command.(DCSG00055119)
-MR 7.13 : Enclosure Device ID is mentioned in the legend for /cx/vall show command.(DCSG00067878)
-MR 7.13 : Cosmetic issue is seen in the command name of /cx /cx show memscrubpatterns ?.(DCSG00067877)
-Commands displayed twice in help description..(DCSG00068441)
-Storcli DPM does not use legend "Resp" in EXT output.(DCSG00060706)
-Enclosure ID is not mentioned as optional in "add Vd " command.(DCSG00058867)
-Port information coming as internal and Location as Blank in when all the drives are removed from UBM2 Backplane.(DCSG00071756)
-DPM delete help is listed under drive delete command group.(DCSG00053537)
-No mention on convention in restart command description..(DCSG00068542)
-Fixing Coverity defects - Uninitialized variable, resource leaks and null referencing.(DCSG00041202)
-Set the PR to run on only configured array, but it complete the PR along with un-configured area..(DCSG00067103)
-Fixing Coverity issues - Resource leaks.(DCSG00054690)
-Storcli throws incorrect error message for /c0 add vd each r0 when Ubad drive is present in the setup..(DCSG00069698)
-Use NVRAM to save PTB information -- API changes.(DCSG00082981)
-Debug logs in FreeBSD is logging timestamp in different lines.(DCSG00069730)
-"/c0 show nolog" shows as "un-supported command.(DCSG00068482)
-Shenandoah_Storcli : The status of PD FW update on multiple drives is not proper when parallel is not included.(DCSG00069693)
-Device type of UBM backplane is displayed as expander in Valvano-32i Controller managed port(C3)..(DCSG00054275)
-Shenandoah_PA2:StorCLI not branding compliant for VD creation command Failure case -IO Policy specif.(DCSG00049610)
-Storcli: px is not described in convention details..(DCSG00065742)
-Unmap enabled not listed for unmap enabled VDs with /cx/vall show all cli command.(DCSG00112331)
-Instance Validation Failed for "storcli64.exe show" and system-schema.json.(DCSG00057156)
-Not able to create R1/R10 with 1MB size and strip size is 1MB.(DCSG00058162)
-Description for storcli output is not proper after collecting the snapdump with id=all.(DCSG00063626)
-StorCLI not reporting default oob settings from nvdata value.(DCSG00066530)
-Executing storcli commands from external path throws error.(DCSG00072117)
-StorCLI: /storcli /cx add vd verbose help ,strip size 512 is missing in help description under strip sizes..(DCSG00146343)
-MR 7.13: Storcli: Caution mentioned instead of note..(DCSG00066554)
-perccli is Reporting incorrect scheduled BBU Learn Date.(DCSG00109638)
-Coverity analysis - Fixing uninitialized variables, resource leaks, and return statements.(DCSG00046460)
-Storcli64.exe /c0 show freespace shows unnecessary data when freespace is not present.(DCSG00055686)
-Schema mapping list is not updated with DPM commands.(DCSG00057823)
-Foreign DHS drive state is displayed as UGood under /c1/fall show all tab..(DCSG00068427)
-MR 7.13: Storcli: logfile is not described in show dpmstat command..(DCSG00065838)
-Statistics is spelled as Statitics in dpm stat commands.(DCSG00057112)
-Cache Vault should be placed instead of battery for "storcli /cx/cv show status ?" help.(DCSG00143868)
-Exit code showing "0" for failed storCLI command due to syntax error.(DCSG00054313)
-Removal of log type from storcli logs.(DCSG00046794)
-Discription for the term "NoVDs" is missing in the legends.(DCSG00068592)
-start dpm returned error.(DCSG00035436)
-Storcli: Show latest events output print shows 0.00 for all the number of events dumped (expected is the number of events queried for).(DCSG00068877)
-Incorrect message noted when Ventura firmware flashed on Aero board.(DCSG00046031)
-No consistency in the help details of "/c0/ex download" commands.(DCSG00064745)
-Storcli license file is not present in the Vmware, Ubuntu & EFI folders.(DCSG00056538)
-Storcli issuing 'add vd r0 drives=all' causes storcli to crash.(DCSG00053963)
-No syntax error for multiple usage of "nolog" parameter in the command..(DCSG00066729)
-Re-Host information is blank when ASO is not enabled.(DCSG00072628)
-SSD Wear guage Parameter "SSD Percent used" to be removed from CLI.(DCSG00074791)
-MR 7.13: Storcli: sx not described in convention details..(DCSG00066310)
-Error message is improper for invalid raid level in volume creation.(DCSG00081057 (Port Of Defect DCSG00083789))
-Set MFG command does not throw an error when executed with empty file..(DCSG00074178 (Port Of Defect DCSG00074209))
-VD delete command works with multiple force options.(DCSG00165527 (Port Of Defect DCSG00167329))
-Syntax error for /c0 show AliLog ?.(DCSG00109790 (Port Of Defect DCSG00112470))
-storcli faults when issue drive poh command on Linux.(DCSG00075870 (Port Of Defect DCSG00075875))
-show memscrubpatterns shows status as success but failed in the description.(DCSG00077082 (Port Of Defect DCSG00103214))
-PH15 PA StorCLI - Segmentation fault observed when Sea IT PSOC image flashed on Ventura.(DCSG00075626 (Port Of Defect DCSG00212680))
-Wrong enclosure details are displayed when slot details are queried..(DCSG00127133 (Port Of Defect DCSG00139981))
-Storcli_VMWare gives failure messages when user tries to set the lanespeed.(DCSG00167210 (Port Of Defect DCSG00167280))
-"Download cpld" command displays incorrect output for MR controller..(DCSG00075734 (Port Of Defect DCSG00075863))
-The properties displayed in the command show htbparams has misspelled fields.(DCSG00104056 (Port Of Defect DCSG00105681))
-Instance Validation Failed for "/call/fall show" and foreign-configuration-schema.json.(DCSG00076415 (Port Of Defect DCSG00078173))
-storclif.exe /cx set copyback ? shows incorrect command name..(DCSG00075718 (Port Of Defect DCSG00075890))
-No description mentioned for "/cx set eghs" command..(DCSG00074290 (Port Of Defect DCSG00074768))
-Unified StorCLI Phase 15: storcli64 /cx add vd each help file missing options and format inconsistencies.(DCSG00139659 (Port Of Defect DCSG00139995))
-Aero Controller DPM does not report Max Response Time under 1 ms..(DCSG00099365 (Port Of Defect DCSG00102548))
-Storcli: Wrcache is mentioned instead of WT| WB.(DCSG00074284 (Port Of Defect DCSG00074767))
-Storclif allows to set Set SubOEMID as 1000 and more.(DCSG00079932 (Port Of Defect DCSG00080836))
-Description for storcli output is not proper after collecting the snapdump with id=all.(DCSG00031711 (Port Of Defect DCSG00063602))
-Storcli /cx show cc , does not shows the "Unit" for CC execution Delay..(DCSG00126229 (Port Of Defect DCSG00129753))
-storcli64.exe /c0/e1/s1 start sanitize throws syntax error..(DCSG00129738 (Port Of Defect DCSG00129750))
-forcehcb is executed with incorrect description in OS level..(DCSG00080961 (Port Of Defect DCSG00083295))
-"Show alilog" command output shows invalid PD ID in Virtual drive info..(DCSG00167354 (Port Of Defect DCSG00167449)
-force is not defined under OPTIONS in storcli64 secureerase help file.(DCSG00148255 (Port Of Defect DCSG00150480))
-Storcli displays "Returned SCSI status for the command : Check condition" along with regular command.(DCSG00138580 (Port Of Defect DCSG00139200)
-Aero Alpha: Storcli stops functioning during run of attached script.(DCSG00034379 (Port Of Defect DCSG00039682)
-/vx is mentioned in the convention for storclif64.exe /cx set cc detailed ?.(DCSG00075700 (Port Of Defect DCSG00075894))
-DCSG00096587.(DCSG00104055 (Port Of Defect DCSG00108742))
-Avenger: ./storcli2 /c0 show ds all command(not present) shows the output of /c0 show all.(DCSG00061163 (Port Of Defect DCSG00080485)
-PATH_1 and PATH_BOTH assigned drives not getting displayed under storcli in WF DDROCK setup.(DCSG00050891 (Port Of Defect DCSG00079275))
-Storcli output starts with "GetCtrlInfo : ProcessLibCommand failed; retCode = 0xFF" for all command.(DCSG00214170 (Port Of Defect DCSG00214248))
-"OS Drive Name" does not display the details in "vall show all" for esxi OS.(DCSG00102559 (Port Of Defect DCSG00103190))
-Storcli: "show bbmt" displays output for an invalid VD..(DCSG00228667 (Port Of Defect DCSG00230346))
-Storcli command description shows none for Download firmware failure.(DCSG00221431 (Port Of Defect DCSG00223281))
-Instance Validation Failed for /call/show_all.json and controller-detailed-properties-schema.json.(DCSG00132488 (Port Of Defect DCSG00137828))
-NoVDs is displayed in dall show output..(DCSG00074628 (Port Of Defect DCSG00074763))
-"reset errorcounters" command mentions options under conventions.(DCSG00074288 (Port Of Defect DCSG00074764))
-PH16 PA - StorCLI - Compare fwprodid help page needs to be updated.(DCSG00167732 (Port Of Defect DCSG00215133))
-Display basic secure boot details for Sea IT controller.(DCSG00074184 (Port Of Defect DCSG00074218))
-No consistency in the description of Force option.(DCSG00074283 (Port Of Defect DCSG00074765))
-Storcli /c0/eall show status extended command fails to generate any output for ARM server backpla.(DCSG00146359 (Port Of Defect DCSG00150479))
-Debug log configuration file for perccli is taking storcliconf.ini.(DCSG00074691 (Port Of Defect DCSG00074757))
-Compare fwprodid command fails for 9500-16i.(DCSG00092943 (Port Of Defect DCSG00115266))
-Handling of controller properties related to drive FW download.(DCSG00138192 (Port Of Defect DCSG00139266))
-In command storcli /cx/ex/sx show DPM type=Ext , Sectors Read (Written) is not displayed correctly.(DCSG00083167 (Port Of Defect DCSG00103210))
-Ph16 PA: Storcli crash observed while running show all with NVMe drives connected.(DCSG00150686 (Port Of Defect DCSG00167881))
-Description for "profileid=" is missing in help and detailed help.(DCSG00152251 (Port Of Defect DCSG00152935))
-EKMS Boot Agent Status is not updating properly..(DCSG00049004 (Port Of Defect DCSG00050289))
-MR 7.15: Storcli: Force option is mentioned as "For".(DCSG00223195 (Port Of Defect DCSG00225259))
-Storcli displays 255 max spin-up drive count in help description instead of 240.(DCSG00098081 (Port Of Defect DCSG00108741))
-"Compare factorysettings" command displays incorrect output for wrong input file.(DCSG00075762 (Port Of Defect DCSG00075888))
-Storcli64 /cx show spinupdrivecount help file description needs update.(DCSG00150052 (Port Of Defect DCSG00150459)
-Segmentation with controller show summary command when controller is in unsupported state.(DCSG00215109 (Port Of Defect DCSG00215118))
-StorCLI show autoconfig does not display all properties it can set.(DCSG00071834 (Port Of Defect DCSG00080859))
-Storcli returns wrong Operating system in Windows..(DCSG00037088 (Port Of Defect DCSG00037336))
-No description for "set autoconfig=R0 immediate" command..(DCSG00129610 (Port Of Defect DCSG00129762))
-Displaying connected portnumber as per API supportMoreThan16Phys.(DCSG00104331 (Port Of Defect DCSG00108740))
-Compare Factory command execution fails in storclif.(DCSG00074182 (Port Of Defect DCSG00074207))
EnhancementRequests:
-HPE : Windows and Linux StorCLI signing.(DCSG00053511)
-Implement changes to secureSign signing tool and infrastructure to support mixed list of PublicKeys that are from SCGCQ and DCSG..(DCSG00105430)
-API change to support ISE completion status.(DCSG00065881)
-MR API: Change event class for SPDM events.(DCSG00134416)
-API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI.(DCSG00222915)
-Perccli: Need a mechanism to get supported device protocols for each controller form factor.(DCSG00117742)
-support for sanitize command.(DCSG00108999)
-Shenandoah: Support for the New Energy Pack states.(DCSG00043240)
-Preboot Trace Buffer [PTB] for Ventura/Aero - MR API.(DCSG00060713)
-Remove Help Text for lanespeed commands.(DCSG00099939)
-Shenandoah: Change the CLI installation Directory name from Megaraid to hpe.(DCSG00053988)
-Porting storcli source from V8 Clearcase to CC9 GCP database.(DCSG00013486)
-Creating VD with 0 MB or GB should not be allowed to succeed --ve case boundary value scenario.(DCSG00048859)
-MR API: NVME Drive Init Error Report and Repair for Aero/Ventura.(DCSG00071534)
-DCSG00129388
-Support to display drive connector name information for SAS3.5 IT Controllers.(DCSG00120994)
-Add segment area into pci information of Megaraid controller in storcli.(DCSG00032694)
-Populate secureboot properties "KeyUpdatePending" and "Remaining Secure Boot Key slots" in StorCLI.(DCSG00101684)
-Remove (hide) PCIe Link form in HII and from CLI for Perc11.(DCSG00077856)
-Define MR_SAS_PHY_CONNECTION.currentSpeed when no devices are connected.(DCSG00071066)
-Signing Linux executables via GPG method in HSM.(DCSG00077215)
-Shenandoah: Creating VD with 0 MB or GB should not be allowed to succeed - Part 2.(DCSG00053587)
-Shenandoah: SSD Wear Gauage.(DCSG00046064)
-MR API changes - Support new DCMD for Platform Security SPDM.(DCSG00068355)
-Add /px linkspeed back to help text.(DCSG00126913)
-HSW Applications to not send close DCMD as the first command to perform Firmware update.(DCSG00055146)
-Update/remove Snapdump save count field in show snapdump command based on FW support.(DCSG00038800)
-Include new field cannotSetMode in MR_AUTO_CFG_PARAMETER structure..(DCSG00072780)
-API changes to expose MR_AUTO_CFG_PARAMETER for NONE mode.(DCSG00151058)
-Add new security events.(DCSG00167313)
-Request for DPMstat support in MegaRAID SAS 3.5 controllers in storcli.(DCSG00032273)
-MR API: update field in event structure..(DCSG00093331)
-Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API.(DCSG00226286)
-SMART Polling Improvement- API Changes.(DCSG00214352)
-References to MR_ENCL_LIST and MR_ENCL_LIST_EXT should be based on the support bit.(DCSG00037323)
-Shenandoah: Type 2 Back plane Support for StorCLI.(DCSG00054795)
-StorCLI: Implementing span depth logic and pd per array count for RAID 10.(DCSG00049781)
-Updating BST scripts to support auto BST through VBAS in clear case version 9.(DCSG00050763)
-FW SAS MEGA API:Change MR_EVT_CTRL_FLASH_DISALLOWED_SB_KEY_CHANGE_PENDING event.(DCSG00086780)
-Revert the CLI Help Text for backwards compatibility to include Dimmer Switch 3.(DCSG00068659)
-Shenandoah: Reverting back the changes made for Span setting for RAID 1 & 10.(DCSG00073393)
-New MFI Stat for the updated recon behavior.(DCSG00229416)
-Shenandoah: Remove Span setting for RAID 1 & 10.(DCSG00043198)
-Restore Factory Default doesn't prompt user to reboot the system after being performed.(DCSG00122000)
-MR API changes - Support new Provisional bit in CTRL INFO and new MFI status for Platform Security.(DCSG00106380)
-Add support for signing MegaRAID Legacy BIOS CU Images (CTLR) images.(DCSG00143847)
-Phase 14 : StorCLI should provide power cycle message post erase all command is executed.(DCSG00039542)
-Enhancement of Enclosure MultiPath algorithm in storcli.(DCSG00075191 (Port Of EnhancementRequest DCSG00079538))
-Support to generate storcli static library.(DCSG00075265 (Port Of EnhancementRequest DCSG00075687)
-Updating toolchain for VMware7.0 GA.(DCSG00134764 (Port Of EnhancementRequest DCSG00136269))
007.1212.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
MR 7.12
Defects:
StorCLI should refer to MR_PD_INFO.properties.ISECapable to display "Cryptographic Erase Capable" field - Revert of SCG(DCSG00014660)
Making the Predictivefaliure check OEM specific in controller health algorithm(DCSG00014971)
HBA345_Dev_UT: Enclosure position value in perccli is same for both front and rear BP's(DCSG00033180
Cisco - CSCVr89052 - PATH_1 and PATH_BOTH assigned drives not getting displayed under storcli in WF DDROCK setup(DCSG00050891)
StorCLI Point release RO DCSG00079546 - Windows binaries are missing from the RO(DCSG00081022)
StorCLI 7.10 point release - /cx erase help not listing all supported commands(DCSG00081294)
StorCLI 7.10 point release - Update license files to RO DCSG00079546(DCSG00081298)
Removal of unsupported phy commands on IT3 controller(DCSG00025416)
Phase 12 - Oct Huawei DET - New PD FW Not Updated After Flashing PD FW (NVMe)(DCSG00015875)
MR_6.14_Huawei: OnDemand Snapdump in Windows gives failure message "RTTdump Feature not supported"(DCSG00020717)
help is not proper for show events and set copyback commands(DCSG00005503)
MR 7.12: Storcli: Instance Validation Failed for "/call show all" and controller-detailed-properties-schema(DCSG00006331)
MR 7.12: Storcli: Instance Validation Failed for "/call/pall show all" and controller-phyerrorcounters-schema(DCSG00006853)
Orion PA9 : Convention comes in same line while performing help for /c0/e0/s0 download.(DCSG00008084)
MR_7.12_Storcli: Xenserver8: "Core dumped" while executing "/call/eall show all" and "/call/eall/sall show all"(DCSG00009400)
Aero DBU PA7 : Init is in progress error message is thrown by Storcli for start migrate command when VD erase is in pro(DCSG00012344)
Orion PA9 : Storcli version mismatch as compared in storcli -v and storcli properties(DCSG00014485)
Orion PA9 : Storcli crashes while performing storcli /c0 show(DCSG00014486)
Storcli show all cmd displaying "AVAGO" in scheduled tasks info(DCSG00014580)
Aero DBU PA7 : Storcli displays multiple error messages when user enters incorrect device ID during migrate operation.(DCSG00014644)
Fixing Coverity defects - resource leaks and null referencing(DCSG00015721)
Correcting the detailed help syntax(DCSG00016268)
MR7.12 StorCLI: Ouptput message Description wrong for StorCLI VD policy change from WT -WB(DCSG00016372)
StorCLI: Fixing coverity defects and adding debug statement(DCSG00019683)
perccli windows binary property page has storcli references(DCSG00019800)
Aero DBU Alpha : Storcli displays incorrect error message for "add vd each r0" command when SED drive is connected in t(DCSG00019816)
Application Exit code is always success for UEFI StorCLI(DCSG00020670)
MR 7.12 LSA "instant secure erase" is not found in storcli as cli use secureerase(DCSG00022096)
Help content for Drive Init is not showing it as Clear operation(DCSG00022893)
MR7.12_Storcli: On drive rebuild, there is a mismatch between the pd rebuild state and respective legend(DCSG00022942)
MR 7.12: Storcli: Instance Validation Failed for "/call start Diag Duration=40" and controller-diag-schema(DCSG00023543)
MR 7.12: Storcli: Instance Validation Failed for "/call show linkconfig " and controller-linkconfig-schema(DCSG00023545)
Aero Alpha : Storcli throw Segmentation Fault in Driver load error handing path -(DCSG00024554)
MR 7.12_Storcli: On ARM server the latest storcli Vendor,Licenses,URL and distribution shows as "AVAGO Technologies"(DCSG00025885)
Aero DBU Alpha - Scheduling is displayed as Schedulling under "/cx set pr ? " command description(DCSG00027203)
Add warning/recommendation messages for changing lane speeds(DCSG00027869)
Orion MR : Description for storcli output is not proper after collecting the snapdump with id=all(DCSG00031711)
Aero Alpha: Storcli stops functioning during run of attached script(DCSG00034379)
Storcli returns wrong Operating system in Windows.(DCSG00037088)
MR 7.12_Storcli: The latest storcli vmware build reference URL shows "http://www.lsi.com"(DCSG00039104)
MR 7.12_Storcli: The latest storcli vmware build 007.1209.0000.0000 shows older package version(DCSG00039112)
PERC 11:EKMS:PKG 2973: EKMS Boot Agent Status is not updating properly.(DCSG00049004)
PH13 StorCLI PA - Update help section about 'nolog' option(DCSG00002975)
PH13 PA - StorCLI - Incorrect message for /call/pall show all command(DCSG00003003)
StorCLI_7.12_Ph13:Phyreset Fails on IT controllers(DCSG00005488)
PH13 PA - StorCLI - NVMe drive linkspeed not seen with /cx/pall show(DCSG00009522)
With IT controller for set or reset with invalid phy is not showing error(DCSG00010226)
Aero_storecli:Using latest storecli Firmware product id parameter value fail to display.(DCSG00011446)
MR_7.12: Storcli: Segmentation Fault for "storcli64 page"(DCSG00012563)
Storcli ph13: Fixing array size for function DEBUG_LOG(DCSG00014665)
Aero Orion IT:- Mismatched phy info listed for 440-16e/440-16i(DCSG00023320)
Enclosure position value in storcli is same for both front and rear BP's(DCSG00031302)
Misleading error message when create unmap VD with storcli64.exe /c0 add vd each r0 unmap using unmap and non-unmap PDs(SCGCQ02059720)
StorCLI: Debug prints enabled in latest Phase 12 PA storCLI.efi image(SCGCQ02097317)
Json Schema for the command "storcli /cx/ex show phyerrorcounters" needs to be updated(SCGCQ02101372)
MR 7.11: Storcli: Instance Validation Failed for "/call show all" and system-schema.json(SCGCQ02112192)
DBU Aero PA4 : Cosmetic error is seen in command description for Show SSDThermalPollInterval ?(SCGCQ02124673)
Aero A0 PA4: "Storcli /c# set jbod=on" shows success but does nothing(SCGCQ02117219)
Aero (DBU PA4):Storcli: Junk character in PD start locate command description.(SCGCQ02125654)
Phyreset Fails on IT controllers and update help(SCGCQ02169242)
Drive mode-e fw download with activatenow is not working(SCGCQ02142068)
MR 7.11: Storcli: Instance Validation Failed for "/call/eall show status extended" and enclosure-status-extended-schema.json(SCGCQ02150924)
MR7.11_Storcli: Incorrect error description while creating r1 with single drive(SCGCQ02165933)
Phase 12 - Oct Huawei DET - "./storcli64 /c0/pall show" Command Fails With "Null pointer exception"(SCGCQ02175414)
Phase 16 (IR) - Oct Huawei DET - Unsupported Drive State is Displayed for "./storcli /c0 show" Command(SCGCQ02170389)
MR 7.11 - Oct Huawei DET - Nomenclature Issue for "rbld=Rebuild" In Storcli Show Help Menu for SAS3516(SCGCQ02170197)
Usage of 64 bit address instead of 32bit address while sending commands to FW in uEFI driver less environment(SCGCQ02174934)
MR_7.10_Storcli: Storcli displays incorrect error message for unmap VD creation with regular HDD drives.(SCGCQ02019751)
PH12 PA - StorCLI crashes when call/pall show executed with SAS3 & Ventura boards(SCGCQ02103217)
PH12 PA - StorCLI - Debug StorCLI binary is placed in both places of EFI dir RO SCGCQ02085693(SCGCQ02091140)
PH12 PA - Update readme file in VMwareOP64 folder in accordance with PR SCGCQ01923533(SCGCQ02108550)
MR 7.11: Storcli.efi: In ARM server UEFI shell, storcli.efi hangs forever when storcliconf.ini is present(SCGCQ02115036)
Aero (DBU PA4):Storcli: VD legend is missing in "/call/vall show expansion" command.(SCGCQ02124508)
Aero DBU PA4 : storclif /cx show configautobalance ? help output shows the name as "show NCQ"(SCGCQ02124632)
Configuring multiple lane speed is working only for fisrt ID, Rest were ignored(SCGCQ02136333)
Aero (DBU PA5):Storcli: Storcli: "/c0 set patrolread ?" lists detailed help and snapdump rttdump is mentioned as optional.(SCGCQ02140873)
MR 7.11: Storcli: Instance Validation Failed for "/call/eall show status" and enclosure-status-schema.json(SCGCQ02150921)
Aero (DBU PA5):Storcli: Force is not mentioned as key word in "/cx/vx del" error message.(SCGCQ02142017)
MR7.11_Storcli: On drive rebuild, there is a mismatch between the pd rebuild state and respective legend(SCGCQ02165944)
Aero (DBU PA5):Storcli: "Ctrl" legend not mentioned.(SCGCQ02146822)
MR7.11_Storcli: storcli set securitykey detailed help does not show description for all the options(SCGCQ02096732)
MR7.11_Storcli: storcli show output shows UBUnsp as UBad Unsupported where as UGUnsp just Unsupported(SCGCQ02096722)
Aero IT - PA3 - StorCLI crashes for 'storcli J command(SCGCQ02117749)
Lenovo Orion IT:- Command to flash UEFI on Aero/sea HBA from storcli/scrutiny fails(SCGCQ02137751)
Flashing of Completeflash fails on Sea IT controller(SCGCQ02139780)
StorCLI: Fixing coverity defects(SCGCQ02123769)
MR 7.11: Storcli: Instance Validation Failed for /call/show_smartpollinterval.json and controller-smartpollinterval-schema.js(SCGCQ02135516)
DBU PA5 Aero : Background operations keep on progressing after hitting /c0 shutdown from storcli(SCGCQ02132024)
Aero (DBU PA5):Storcli: No "Rbld" legend during rebuild.M(SCGCQ02146819)
complete Lane WWID is not displayed(SCGCQ02145716)
Convention comes in same line while performing help for /c0/e0/s0 download.(SCGCQ02176681)
Adding missing syntax for the command deviceorderbyfirmware(SCGCQ02121705)
MR 7.11: Storcli: Instance Validation Failed for "/call/vall show unmap" and vd-unmap-schema.json.(SCGCQ02113316)
Aero (DBU PA5):Storcli: "completeflash" is listed in Windows help file.(SCGCQ02141931)
Aero (DBU PA5):Storcli: Force option not mentioned in "/cx/dx add mirror" and "/cx/vx start init" command.(SCGCQ02140878)
Force option is needed only for Parallel Drive microcode update, but it allows to take for normal also(SCGCQ02177086)
StorCLI Copyright Notice Needs to be updated(SCGCQ02174040)
Wrong error message when create unmap VD with unmap disable on controller(SCGCQ02064118)
Aero DBU PA4 : storclif /cx delete colinfo ? shows syntax error(SCGCQ02124492)
MR 7.11: Storcli: Instance Validation Failed for "/call show" and controller-properties-schema.json.(SCGCQ02108770)
PH12 PA - StorCLI version not getting printed for show file command(SCGCQ02105185)
Aero DBU PA4 : Command name shown in help output differs for storclif.efi /cx show limitmaxrateSATA ?(SCGCQ02124667)
Aero DBU PA4 : Redundant information is displayed for set driveactivityled command in storclif.(SCGCQ02124675)
Aero (DBU PA4):Storcli: Wrong reference of "page=[X]" as part of syntax error message.(SCGCQ02124252)
Aero DBU PA4 : storclif.efi /cx show deviceorderbyfirmware ? throws syntax error.(SCGCQ02124528)
MR 7.11: Storcli: Instance Validation Failed for /call/show_consistencycheck.json and controller-cc-schema.json(SCGCQ02135510)
Phase12-Storcli- In Windows storcli64.exe /c0 show htbparams is showing random values for SAS3 controller(SCGCQ02125598)
Aero (DBU PA5):Storcli: No description of patrolread "OFF" and optional is mentioned as {}.(SCGCQ02140859)
PH12 BETA - /cx erase help not listing all commands(SCGCQ02146466)
Aero (DBU PA5):Storcli: No consistency in the usage of "|" in the command such as "on|off".(SCGCQ02142022)
Phase 12 - Oct Huawei DET - Delay Option In PD Download Operation is Not Honored(SCGCQ02176690)
With IT controller for set or reset with invalid phy is not showing error(SCGCQ02181823)
Updating phy link reset logic for IT cards with respect to storelib changes(SCGCQ02184862）
Drives connected to active backplanes not showing the phy info in connector name(SCGCQ02112424）
PH12 PA - StorCLI - 9310-8i IR FW download fails(SCGCQ02121783）
MR 7.11: Storcli.efi: On ARM server, incomplete configuration data received error is observed for any storcli.efi command(SCGCQ02114898）
Aero PA6 - storcli snapdump id=x errors without optional file parameter(SCGCQ02161748）
PH11 - StorCLI - Incorrect message for /call/pall show all command(SCGCQ02169536)
cli does not allow to do crypto erase on SATA SSD.(SCGCQ02147075)
MR7.11_Storcli: Storcli stop erase needs an help file update(SCGCQ02168895)
Phase 12 - Oct Huawei DET - Incorrect Help Menu For "show phyerrorcounters"(SCGCQ02180495)
Phase 12 - Oct Huawei DET - New PD FW Not Updated After Flashing PD FW (NVMe)(SCGCQ02191421)
Aero PA4 DBU : Storclif doesn't show details for VF/PF in help file for vfmap command .(SCGCQ02123789)
Aero (DBU PA4):Storcli: Typo in /c0 add vd detailed help.(SCGCQ02119091)
Aero (DBU PA4):Storcli: /c0 compare lists /c0/px compare command.(SCGCQ02124246)
StorCLI: Fixing coverity issue in libmod(SCGCQ02123790)
SWR:Storcli: "Show" and "show all" output Description is shown as "No Enclosures found"(SCGCQ02146814)
MR 7.11 storcli -help missing the verbose option(SCGCQ02158600)
Phase 12 - Oct Huawei DET - PD FW Download is failing for Mode f(SCGCQ02168197)
PH12 PA - StorCLI - Incorrect string displayed with show command in FreeBSD 11.2(SCGCQ02094529)
PH12 PA - StorCLI /cx/pall show fails on 9400-8e board(SCGCQ02119004)
MR 7.11: Storcli: Instance Validation Failed for "/call/v5 set bootdrive=off" andcontroller-bootdrive-schema.json.(SCGCQ02115786)
StorCLI: Fixing coverity defects for second run(SCGCQ02125523)
MR 7.11: Storcli: Instance Validation Failed for /call/show_all.json and controller-detailed-properties-schema.json(SCGCQ02135526)
Aero (DBU PA5):Storcli: /c0 set ? lists bbu,mx,px and lnx commands.(SCGCQ02136689)
Aero DBU PA4 : Storclif should not display vendor name in storclif.efi /cx/ex download help command(SCGCQ02123765)
Aero (DBU PA5):Storcli: Improper spacing for the linkspeed description and "YY" parameter leads to confusion.(SCGCQ02139910)
MR 7.11: Storcli: Instance Validation Failed for /call/show.json and controller-properties-schema.json(SCGCQ02135420)
MR 6.14 - Oct Huawei DET - "Rbld=Rebuild" is Not Available In Storcli Show Help Menu for SAS3108(SCGCQ02170181)
MR 7.11: Storcli: Instance Validation Failed for "/call/cv show all" and cache-vault-detailed-schema.json(SCGCQ02150651)
Aero (DBU PA5):Storcli: Help notes needs an update.(SCGCQ02146823)
Phase 12 - Oct Huawei DET - Incorrect Status for PD FW Download (Ventura IT)(SCGCQ02173203)
Phase 12 - Oct Huawei DET - Incorrect Phy Details Displayed for Ventura IT Controller(SCGCQ02174296)
Enchancement:
To bring MR 7.10 storcli change to CC9 GCP database(DCSG00013486)
Support to generate storcli static library(DCSG00075265)
Bring MR 7.11 storcli change to CC9 GCP database(DCSG00014492)
Updating the Makefile and projects as per new CC/CQ changes(DCSG00003002)
Updating the Json Schema files with respect to the latest code(DCSG00007394)
Controller commands Json Schema files update as per the latest code(DCSG00007435)
Schema validation : Schema update for VD/DG/Foreign related commands(DCSG00007453)
Add UEFI Shell StorCLI support for 64-bit Ventura Gen MR Legacy Boot solutions (solutions without UEFI driver)(DCSG00008200)
Changing the CBB download image type as per new MR API(DCSG00010253)
Migrating StorCLI's 64 bit VMware toolchain to 6.8.7-13394445(DCSG00014503)
PERC 11: Provide ability to expose SEP to host and disable PERC SES management in PercCLI / HII(DCSG00015020)
Supporting build and BST process through VBAS in Clear Case version 9(DCSG00024818)
Windows and Linux StorCLI HSM based signing support(DCSG00031618)
StorCLI PH13: Adding interface for lane display and configuration command for IT controllers.(DCSG00007909)
Atlas Support on Aero-IT(DCSG00008038)
Concern for security key passed in from storcli to be read in process data(SCGCQ02066380)
Support FMP Images in UEFI Version of PERCCli(SCGCQ02078649)
Add segment area into pci information of Megaraid controller in Storlib and storcli(SCGCQ02201178)
Create DVT / PVT PnP IDs for Cisco Pismo Beach card(SCGCQ02108965)
Return pended IOCTLS that was not completed after some numbers of OCRs had been initiated.(SCGCQ02066395)
Enable SnapDump for iMR(SCGCQ02208421)
HDET: Support in storCLI support PD firmware download for 3008IR/3008IT controllers(SCGCQ02160016)
multi VSES implementation(SCGCQ02066438)
Return pended IOCTLS that was not completed after some numbers of OCRs had been initiated.(SCGCQ02066399)
Add displaying list of enclosures in controller show and show all command(SCGCQ02124566)
LibMod changes : MR: 64 Bit Utilities/Application to Support VMWARE ESXi 6.7+(SCGCQ02085102)
SAS 3_5 Ventura family UEFI NVMe drive serial number issue(SCGCQ02074657)
Unmap error message changes as per new description in MR API(SCGCQ02115017)
MR: 64 Bit Utilities/Application to Support VMWARE ESXi 6.7+(SCGCQ02066386)
Lenovo Whitley/Orion - Addendum 7 - Lenovo request to support StorCLI & LSA for Valvano 28i (MR+Cub) and Custom Form Factor(SCGCQ02082612)
007.1022.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
Defects :
- PERCcli Help text is missing description for "Lane Information"(SCGCQ02150899)
- Add NVMe width comments to mr.h(SCGCQ02146846)
- Fix API changes done for NVMe readiness(SCGCQ02142981)
- CLI returns "success" when attempting to set DS3 or DS4 to enabled(SCGCQ02116380)
- CLI returns "success" when attempting to change the H840 controler to eHBA personality.(SCGCQ02114332)
- CLI returns wrong error code upon failure(SCGCQ02084966)
- HPE shenandoah: storcli crashes during show command when DGs present(SCGCQ02065695)
- "Run time to empty" field showing as "Battery is not being charged" when the battery is being charged.(SCGCQ02045324)
- ROP version not displayed with latest ROP version SCGCQ02035462(SCGCQ02041094)
- FW flash fails to load the latest image after upgrade downgrade with resetnow option(SCGCQ02035152)
- retentiontest command is successfully triggering BBU test on Shenandoah controller(SCGCQ02021398)
- Storclio (007.0911.0000.0000) detailed help file doesn't have " locale " option for flashing FW in Dual/Active & Backup mode.(SCGCQ02012025)
- hot spare reference in Add Spare command output(SCGCQ01897463)
- Shenandoah:Strocli show all output return failure but generates output(SCGCQ01929191)
- Junk message "STR_JBOD_OBJ" is displayed in the output of storcli /c0 show JBOD command.(SCGCQ01932770)
- Shenandoah_StorCLI: No legend presend for VD Delete Failure(SCGCQ01936811)
- Shenandoah_StorCLI:Setting Unmap=OFF gives success for a LD when unmap is not supported and not enabled on that LD(SCGCQ01940291)
- Set WrCache= WB ,says success even though VD is in WT.Proper warning message should be given to the user(SCGCQ01940296)
- Legend missing for LD BGI resume/pause commands(SCGCQ01940347)
- System hangs while creating VD in EFI shell.(SCGCQ01945551)
- Shenandoah_StorCLI: Storcli crashes on checking LD preserved cache info(SCGCQ01955069)
- CLI is showing the incorrect OS version(SCGCQ01956276)
- Unified StorCLI : Add extra space to CBB header(SCGCQ01956678)
- PH10 Alpha - StorCLI throws "0 Failed 32782 Failed to get PD Info" when /c0 show executed in EFI(SCGCQ01960322)
- JBOD list is not showing in order when using /cx show(SCGCQ01961527)
- supported personalities has blank value(SCGCQ01965370)
- storcli faults for enclosure show command(SCGCQ01985815)
- MR7.10_PA1: Storcli binaries for RHEL/SLES OS is not present for ARM(SCGCQ02006374)
- NVMe drive displays incorrect information with IT card(SCGCQ02009852)
- MR_7.10_Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set personality" JSON output.(SCGCQ02016762)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for snapdump commands.(SCGCQ02018073)
- MR_7.10_Storcli: No schema file for controller sesmultipathcfg commands.(SCGCQ02018134)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for drive jbod commands.(SCGCQ02018135)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for "/cx get vpd" commands.(SCGCQ02018140)
- MR_7.10_Storcli: Instance Validation Failed between "virtual-drive-detailed-schema.json" and "/call/vall show all "(SCGCQ02018333)
- MR_7.10_Storcli: bbu-show-modes-schema.json file is not in JSON format.(SCGCQ02019740)
- Instance Validation Failed between " controller-lane-show-schema.json" and "/call/lnall show"(SCGCQ02019746)
- Pending Image details are not populated after FW upgrade and downgrade.(SCGCQ02024065)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "/call show all "(SCGCQ02032911)
- MR_7.10_Storcli: Add VD command output is not in JSON format.(SCGCQ02034493)
- Instance Validation Failed between "vd-unmap-schema.json" and "/call/vall show unmap"(SCGCQ02035370)
- remove the maxconcurrentpd check from storcli and report fw returned failure(SCGCQ02053910)
- Storcli: "resume migrate" command does not show syntax error.(SCGCQ02061340)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show_all"(SCGCQ02062957)
- Show Snapdump help command lists delete snapdump details as well.(SCGCQ02064836)
- Storcli: "show config" command shown as Un-supported.(SCGCQ02064839)
- PH11 Alpha - StorCLI 'show file' command throws segmentation fault for complete flash image in FreeBSD(SCGCQ02065691)
- Storcli: No schema files for htbparams commands.(SCGCQ02065698)
- "Delete snapdump" command shows same description "Snapdump clear" for success and failure case.(SCGCQ02065734)
- Incorrect error message displayed while creating R10 VD when no free space available.(SCGCQ02067575)
- Schema file updates for controller show all output change for defect SCGCQ02048150(SCGCQ02069817)
- Typo in storcli /c0 set linkspeed help(SCGCQ02070951)
- Aero (DBU PA2): Storcli: No syntax error displayed for "storcli mronly" command.(SCGCQ02072746)
- Wide port info is not displayed under connector name for Backplane attached drives.(SCGCQ02076923)
- Empty data is listed when we query for show linkconfig(SCGCQ02076931)
- htbparams help output needs update.(SCGCQ02077156)
- show/set lane speed shows success when we are in SAS profile(SCGCQ02078437)
- Libmods: show.set lane speed shows success with wrong data when we are in SAS profile(SCGCQ02078513)
- Recon command (./storcli /cx set recon) is throwing syntax error.(SCGCQ02081415)
- storcli /c0/ex/s23,24 show patrol read doesnt not show error for slot 24 (Invalid Slot)(SCGCQ02082142)
- Aero (DBU PA2): Storcli show detailed help does not list "show all " command.(SCGCQ02082303)
- Aero (DBU PA2): Storcli: Get rttdump detailed help shows syntax error.(SCGCQ02082460)
- Storcli: Incorrect message while executing "storcli64.exe /c0/v0 del discardcache"(SCGCQ02083828)
- Failure status for /call/sall and /call/eall/sall command.(SCGCQ02084549)
- Storcli: Error in /c0/f0 command output.(SCGCQ02089892)
- StorCLI listing PD Slot Status as "Incorrect Status Value" for configured PD's(SCGCQ02090770)
- Storcli doesn't exit with controller status message after doing OFU.(SCGCQ02091548)
- Libmod changes for SCGCQ02090770 (SCGCQ02096774)
- Aero (DBU PA3): Storcli: FW hits Megamon while executing storcli in EFI shell when EFI Driver is unloaded.(SCGCQ02097647)
- StorCLI crashes for 'storcli J command(SCGCQ02117749)
- Storcli: VD legend is missing in "/call/vall show expansion" command.(SCGCQ02124508)
- Controller Health Status not consisten across applications(SCGCQ02182243)
- Perccli does not enable Power Save mode for UG & HS type 1 & type 2. (SCGCQ02125408)
- StorCLI: Delete config failure message need correction(SCGCQ02086726)
- StorCLI:VD reference in Delete preserved cahce command output -Branding(SCGCQ02083992)
- VD reference in set JBOD command output message(SCGCQ02078507)
- storclif.exe /c0/ex/sx show poh should show proper message during command execution.(SCGCQ02075242)
- STORCLI: Show command output having wrong legend for Slt for oem Hercules(SCGCQ02067616)
- Grammatical error in Perccli message(SCGCQ02065513)
- BSOD observed when VD/JBOD Creation/Del and snapdump Cycles are initiated.(SCGCQ02045967)
- VD legend missing in the legend for Foreign config show all output(SCGCQ02016798)
- Hercules:Shenandoah:Transformation is coming as Reconstruction , while migrating the Raid 1 to Raid 5 .(SCGCQ01897468)
- Mis-spelled words in StorCli's Help(SCGCQ01898853)
- Hot spare reference in storcli.exe /cx/ex/sx show all command output(SCGCQ01905019)
- Reference to VD in storcli.exe /c1/jbodall delete command output(SCGCQ01905077)
- Fixing coverity issues Removing dead code and Out of bound access(SCGCQ01924504)
- Shenandoah_StorCLI: HotSpare reference in Add VD Command output(SCGCQ01936887)
- storcli /c0 show events output not listing the Event ID's(SCGCQ01940290)
- Shenandoah_StorCLI:Hot spare reference in storcli64 /cx show/set restorehotspare command outputs(SCGCQ01940437)
- Shenandoah_StorcLI:Drive Group reference in Add dedicated spared drive command in CLI(SCGCQ01955167)
- Intel NVMe drive "Model Number" displayed incorrect under Device Attributes(SCGCQ01957949)
- Aero: Segmentation Fault in storcli /c0 show all(SCGCQ01996444)
- Storcli throws an 'Incomplete foreign configuration' error when there is no enclosure connected(SCGCQ02006450)
- storcli gives error when the lane configuration is set as X8 (SCGCQ02007152)
- MR_7.10_Storcli: No schema file for controller unmap commands(SCGCQ02016749)
- MR_7.10_Storcli: Instance Validation Failed "controller-restorehotspareoninsertion-schema" and "set restorehotspare"(SCGCQ02016765)
- MR_7.10_Storcli: Instance Validation Failed "controller-properties-schema" and "/c0 show"(SCGCQ02016768)
- MR_7.10_Storcli: controller-detailed-properties-schema.json or "/call show all " output not in JSON format(SCGCQ02016771)
- MR_7.10_Storcli: Instance Validation Failed between "controller-autoconfig-schema.json" and "show autoconfig" JSON output.(SCGCQ02018227)
- MR_7.10_Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" JSON output.(SCGCQ02018277)
- MR_7.10_Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON output.(SCGCQ02018305)
- MR_7.10_Storcli: Instance Validation Failed between "system-schema.json" and "./storcli show" and "show all" JSON output.(SCGCQ02018313)
- MR_7.10_Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/eall/sall show all"(SCGCQ02018327)
- MR_7.10_Storcli: Instance Validation Failed between "cache-vault-detailed-schema.json" and "/call/cv show all "(SCGCQ02019729)
- Storcli displays drive state as UBad instead of UBad (unsupported)(SCGCQ02031615)
- Instance Validation Failed between "drive-group-hidden-schema" and "/c1/dall set hidden" & "set security"(SCGCQ02040779)
- Fixing coverity issues Fixing resource leaks(SCGCQ02043601)
- Storcli help file should show the expand size format.(SCGCQ02047109)
- Updating the storcli schema mapping document (SCGCQ02050586)
- PH11 Alpha - StorCLI - Parse error observed for command 'StorCLI J' while validating Jason(SCGCQ02053030)
- JSON-SCHEMA : IT-Controller Json-schema validation erros in MR_SAS_Unified_StorCLI_7.10(SCGCQ02053914)
- Aero: Storcli : Storcli crashed when Firmware upgrade tried on Sea controller(SCGCQ02060276)
- Aero (DBU PA2): Storcli: JSON readme file does not have complete VD and PD support list.(SCGCQ02061328)
- Instance Validation Failed bw "enclosure-drive-detailed-schema.json" & "/call/eall/sall show all"(SCGCQ02062958)
- PH11 Alpha - StorCLI - Compare linkspeed command failed for 6Gbps link(SCGCQ02063932)
- Invalid aero controllers are not displayed with apt message in driver less mode(SCGCQ02065581)
- Storcli connector display not matching with Aero board 9560-16i.(SCGCQ02072448)
- Aero (DBU PA2): Storcli: /cx/mx command does not mention about "Auto" settings.(SCGCQ02082208)
- Storcli: Force is mentioned as optional in snapdump delete command. (SCGCQ02083822)
- Help of /cx/px compare command needs update and /cx/px reset ? shows syntax error.(SCGCQ02084752)
- No proper legends in /fall output.(SCGCQ02100491)
- Aero (DBU PA3): Storcli: Incorrect schema mapping for "/cx set autoconfig " command.(SCGCQ02101558)
- Storcli: OCR helps needs update.(SCGCQ02113241)
- Storcli: No proper description of set and show sesmultipathcfg.(SCGCQ02113358)
- StorCLI: File sync issue with rel and dev stream for MR 7.10 (SCGCQ02116806)
- Storcli script stops with error "can't fork: Cannot allocate memory" (SCGCQ02184427)
- IT- CLI treats EID and Partner Device ID as two different enclosure during pd info command and fails.(SCGCQ02185442)
- "/eall show" will not show enclosure details if it is in multitpath & no drives connected.(SCGCQ02186022)
- Legacy messages present with create and rekey of securitykey on controller(SCGCQ01581843)
- Shenandoah_StorCLI:VD reference in CLI outout for Firmware update command failure case(SCGCQ02083991)
- StorCLI: VD listing for c0 show and vall show is toggled (SCGCQ02078936)
- output information for link configuration is displayed incorrectly(SCGCQ02073046)
- Drive Groups is shown instead of arrays in show all command(SCGCQ02048660)
- Help is not updated for get snapdump without ID option.(SCGCQ02046991)
- StorcliO show oob command fails for Invader based cards(SCGCQ02040783)
- Adding debug logs to Mfi files(SCGCQ01891583)
- MR7.8_Storcli: Storcli fails to install on ARM server with Missing Maintainer message(SCGCQ01919830)
- StorCLI show SAS address for NVMe drives (SCGCQ01921258)
- Unified StorCLI 7.9 : Fixing coverity issues - Dead code,resource leaks,and memory corruption - Part 1(SCGCQ01925503)
- Incorrect help option for set autoconfig in StorCli's Help(SCGCQ01932035)
- Unmap enabled property is shown in VD detailed properties when controller does not support unmap (SCGCQ01932177)
- Unified StorCLI - Aero : "FullFlashImage" environmental variable component stamp change(SCGCQ01963738)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for /cx/px commands.(SCGCQ02018137)
- MR_7.10_Storcli: Instance Validation Failed between "enclosure-schema.json" and "/call/eall show" JSON output.(SCGCQ02018322)
- MR_7.10_Storcli: Instance Validation Failed between "foreign-configuration-schema.json" and "/call/fall show"(SCGCQ02024327)
- Aero UTP: storclif /call show commands output contains "Count 4 exceeded for token id #" (SCGCQ02034064)
- Aero IT - PA1 - StorCLI - BIOS verion not displayed with flash file using 'show file' command(SCGCQ02034490)
- failure in StorCLI enclosure show status (SCGCQ02040640)
- unmap attribute is not mentioned in help file command "add vd each r0".(SCGCQ02042106)
- Incorrect status displayed for pause rebuild command.(SCGCQ02043610)
- PH11 PA - StorCLI - Segmentation fault seen when 'compare linkspeed' executed on Fury C0 board(SCGCQ02044777)
- Port information is not displayed for Vses Backplane(SCGCQ02053070)
- "c0 delete ?" does not list snapdump command.(SCGCQ02053639)
- Incorrect status displayed for resume copyback command.(SCGCQ02062834)
- Aero (DBU PA2): Storcli: Instance Validation Failed bw "vd-operations-migrate-schema.json" & "start_migrate"(SCGCQ02062960)
- Aero (DBU PA2): Storcli: Result shows blank for "resume patrolread" failure case.(SCGCQ02064795)
- Fail to set the linkconfig . (SCGCQ02070797)
- Storcli /c2 set linkconfig conname=c0,c1 configid=14 returns invalid syntax error(SCGCQ02070953)
- Aero DBU PA2 : Syntax error is seen in storcli /cx(x|all (SCGCQ02077085)
- Aero (DBU PA2): Storcli: Syntax error for "/c0 download psoc/efibios/cpld/fcode ?" download commands.(SCGCQ02077175)
- Storcli throws different error messages for show status command in Ventura and Aero(SCGCQ02078409)
- Incorrect string displayed in show command in FreeBSD OS(SCGCQ02082949)
- MR_7.10_Storcli: "storcli show file=filepath" command shows failure status.(SCGCQ02085630)
- PCI Linkconfig configid status is failure, even though it was set(SCGCQ02086669)
- Storecli_Aero: Using latest storecli show file command "Aero-DVT -HBA 9500-16e" board output version number shows wrong.(SCGCQ02089427)
- Libmods changes for defect SCGCQ02062957(SCGCQ02089862)
- Help update for "add vd cachevd" command as Normal VD is created with failure status.(SCGCQ02091155)
- Preserved cache help file shows a mismatch in command and the convention.(SCGCQ02106218)
- Aero DBU PA4 : Storcli doesn't show the convention details properly for storclio /cx/px show command(SCGCQ02113377)
- Aero (DBU PA4):Storcli: Syntax error for /c0 show AliLog ?(SCGCQ02113506)
- Aero (DBU PA4):Storcli: Typo in /c0 add vd detailed help.(SCGCQ02119091)
- Misleading error msg "157 Failed Cannot mix unmap and non-unmap physical drives in same array"(SCGCQ02151484)
- Cryptographic erase field is shown "yes" but crypto erase fails.(SCGCQ02175346)
- Device Type for non-UBM backplanes are being shown as Enclosure instead of Backplane(SCGCQ02101095)
- Multiple status messages are displayed in the output (SCGCQ02073042)
- Controller health status is shown as optimal when megacell cable is disconnected.(SCGCQ02021393)
- Storcli, should fail the command "get snapdump id=0 file=snapdump.zip norttdump"(SCGCQ01889700)
- Shenandoah_StorCLI:32 Binary crashes on giving invalid input to the command storcli.exe /c0/jbod0 show(SCGCQ01905831)
- For NVMe drive use the term NVMe instead of PCIe(SCGCQ01923119)
- PD show all command displays SSD weargauge details , which is not required.(SCGCQ01927864)
- MR_7.10_Storcli: Junk character in error message while creating SED vd with regular HDD drives.(SCGCQ02016701)
- MR_7.10_Storcli: Incorrect command syntax mentioned in Schema_mapping_list.xlsx file for "/cx set autoconfig" command.(SCGCQ02018097)
- Instance Validation Failed between "vd-operations-bgi-schema.json" and "/call/v1 show bgi " and "show init".(SCGCQ02035551)
- Storcli shows incorrect output for delete events command(SCGCQ02045816)
- BreakMirror RAID Support coming as Yes, even when Breakmirror is not supported(SCGCQ02048150)
- Spell mistake on support ondemand snapdump property of show all output(SCGCQ02053923)
- StorCLI displays expansion as successful even when there is no free space to expand(SCGCQ02057361)
- Instance Validation Failed between "controller-patrolread-schema.json" and "/call resume patrolread"(SCGCQ02062942)
- PH11 Alpha - StorCLI - 'show file' command displays incorrect message after reading uploaded bios file(SCGCQ02063689)
- Need a space between atleast with StorCLI error message "Unmap is not supported atleast on one device"(SCGCQ02064120)
- Storcli:"resource already in use" error message displayed when trying to create VD with one UG and one UBUnsp.(SCGCQ02064828)
- Aero (DBU PA2): Storcli: Inconsistency in "add vd" command syntax.(SCGCQ02082196)
- Details are displayed twice in "/cx/bbu start ? "(SCGCQ02100905)
- Storcli: set termlog shows [=on|off] mentioned as optional.(SCGCQ02113353)
- CLI is missing the JBOD PD size for SysPDs when using the "show jbod" command(SCGCQ02132277)
- Percli returns “invalid arguments" when trying to create a VD using some PDs already configured in a VD and some U(SCGCQ02122169)
- Topology information missing from Storcli output(SCGCQ02048612)
- (SCGCQ02040597)
- Unified StorCLI: StorCLI does not return the return code from SLIT/SLIR3 to explorer/command processors(SCGCQ01925156)
- Virtual drive reference in Delete Preserved cache command output(SCGCQ01940333)
- Storcli not working on large config setup when some of the drives are missing or the system has foreign config.(SCGCQ01940805)
- Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01948579)
- Shenandoah : Firmware receives incorrect erase type for sanitize crypto erase option(SCGCQ01958564)
- Storcli shows BBU present instead of EnergyPAck in HWcfg for StorCLI /cx show all output.(SCGCQ01985592)
- Aero:Storcli: Adaptertype shown as UNKNOWN(X0) for Sea (3816_Eval) IT Controller(SCGCQ02008219)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for errorcounters commands.(SCGCQ02018078)
- Storcli reported "Boot Volume Supported = NO" eventhough ctrl boot with OS on vd.(SCGCQ02030652)
- There is no error message for smart drive failure command.(SCGCQ02040645)
- Storcli help file doesn't show recon rate command instead it shows migrate rate.(SCGCQ02046036)
- JSON Schema : Updating the schema list with Virtual drive command set(SCGCQ02057360)
- storecli_Aero:In linux error message observed in the show output.(SCGCQ02057699)
- Checking in JSON schemas(SCGCQ02061305)
- Junck character displayed in Virtual SES phy id, when we query phyerror counter for enclosure.(SCGCQ02094970)
- Aero (DBU PA3):Storcli: Help of /cx/px reset does not mention about option hard reset.(SCGCQ02100896)
- BBU show detailed help does not list "show learn " command.(SCGCQ02100915)
- Storcli: Instance Validation Fails for all /call/e65/sall commands where "e65 is not found".(SCGCQ02101564)
- Storcli: Remove Nytro supported options in "/cx [start] flush|flushcache [cachecade | ALL]" help.(SCGCQ02113484)
- MR7.10 cli return mesg. typo after ctrl restart then immediately running storcli64 /c0 show.(SCGCQ02113833)
- Storcli: /c0 compare help lists /c0/px compare command.(SCGCQ02124246)
- Serial number not displayed fully in 7.10 StorCLI 007.1017.0000.0000 for IT Controller(SCGCQ02173789)
- Hide BBU details from the command "storcli /c0 show alilog" for HPE(SCGCQ01937259)
- Disk group is displayed instead of array on HPE platforms(SCGCQ01965366)
- MR_7.10_Storcli: unmap attribute is not mentioned in "/c0 add vd" command syntax in Schema_mapping_list.xlsx file.(SCGCQ02016758)
- Storcli pop-up a message "controller not found" during chip reset , rather than controller busy.(SCGCQ02024740)
- "Invalid RAID level" error message while creating R10 VD.(SCGCQ02034471)
- MR_7.10_Storcli: Instance Validation Failed between "controller-patrolread-schema.json" and "/call pause patrolread"(SCGCQ02035437)
- Instance Validation Failed for "/call show and /call show all".(SCGCQ02101432)
- Instance Validation Failed bw "drive-group-detailed-schema.json" and "/call/dall show all".(SCGCQ02101513)
- Autoconfig options are allowed to set with latest storcli(SCGCQ02053643)
- Unified StorCLI Phase 10 : Image checksum should not be performed for aero images(SCGCQ01942200)
- Aero DBU PA1:Storcli: Instance Validation Failed "controller-properties-schema" and "/call show" command.(SCGCQ02035439)
- Fixing coverity issues Fixing resource leaks and explicit NULL dereferencings(SCGCQ02042242)
- Unified StorCLI : Fixing resource leaks - Part 1(SCGCQ02042513)
- Updating Schema mapping doc and fixing validation errors (SCGCQ02057434)
- Storcli: Instance Validation Fails for vd-bootdrive-schema.json and vd-unmap-schema.json.(SCGCQ02101568)
- Aero_storecli:Using latest storecli firmware download fail with noreset option.(SCGCQ02101570)
- Aero DBU PA4 : Syntax error is seen for the command - storclio.efi /cx/px set state ?(SCGCQ02113123)
- PD info incorrectly shows Number of Blocks for >TB drives(>3TB in my case(SCGCQ02183653)
- CLI is returning "success" when attempting to set bios mode to Ignore Errors.(SCGCQ02121017)
- On Demand SnapDump does not show proper time stamp.(SCGCQ02084833)
- Storcli issuing 'add jbod drives=all' causes storcli to crash(SCGCQ01892288)
- Initialize the MFG structure(SCGCQ01901166)
- Aero:Storcli: Adaptertype shown as UNKNOWN(X0) for Aero (3916_Eval) IT Controller(SCGCQ02021194)
- Instance Validation Failed between "drive-group-schema.json" and "/call/dall show " and /call/dall show all(SCGCQ02040756)
- PH11 PA Storcli: Incorrect error message shown while programming invalid sasaddress(SCGCQ02042296)
- Unified StorCLI : Individual SL_INIT_LIB calls are made for every SL command invocation(SCGCQ02047100)
- Updating storcli-cmd-list.xlsx for Drives(SCGCQ02056199)
- Message with Incorrect controller object is displayed while setting SSD Caching on VD(SCGCQ02057085)
- Storcli displays grammatically incorrect message in detailed help file.(SCGCQ02097641)
- MR_7.10: Storcli: Property is shown as SCSI Umap instead of SCSI Unmap.(SCGCQ02101572)
- Storcli: /c0 show detailed command does not list /cx/px show phyerrorcounters and /cx show vpd.(SCGCQ02113262)
- Aero (DBU PA4):Storcli: Incorrect description of "/c0/v0 show migrate" command.(SCGCQ02113511)
- Wrong reference of "page=[X]" as part of syntax error message.(SCGCQ02124252)
- Storcli: Junk character in PD start locate command description.(SCGCQ02125654)
- Storcli doesn't exit with controller status message after doing OFU. (SCGCQ02101069 port of SCGCQ02091548)
- perccli /c0 show all lists topology without any DG's present (SCGCQ02085925 port of SCGCQ01998332)
- MR_7.10_Storcli: bbu-show-modes-schema.json file is not in JSON format.(SCGCQ02079618 port of SCGCQ02019740)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for drive jbod commands.(SCGCQ02079592 port of SCGCQ02018135)
- Libmods: HPE serial number display(SCGCQ02062634 port of SCGCQ01885657)
- Aero DBU PA1:Storcli: Instance Validation Failed "controller-properties-schema" and "/call show" command.(SCGCQ02061387 port of SCGCQ02035439)
- MR_7.10_Storcli: unmap attribute is not mentioned in "/c0 add vd" command syntax in Schema_mapping_list.xlsx file.(SCGCQ02050535 port of SCGCQ02016758)
- MR_7.10_Storcli: Instance Validation Failed between "virtual-drive-detailed-schema.json" and "/call/vall show all "(SCGCQ02050471 port of SCGCQ02018333)
- failure in StorCLI enclosure show status (SCGCQ02043616 port of SCGCQ02040640)
- Expander FW download using storecli utility crashs.(SCGCQ01979616 port of SCGCQ01979599)
- Hide "set pdfaileventoptions" command from CLI Help(SCGCQ01892551 port of SCGCQ01880722)
- Error message when Maximum number of VDs are reached (SCGCQ01911777 port of SCGCQ01856544)
- Adding CLI command to display/toggle new controller property.(SCGCQ01927583 port of SCGCQ01106982)
- System hangs while creating VD in EFI shell.(SCGCQ01945574 port of SCGCQ01945551)
- storclio command not working to update FW on SATA disk(SCGCQ01963953 port of SCGCQ01918814)
- Storcli is not showing foreign configs if user has SED drive which is in foreign(SCGCQ01963954 port of SCGCQ01937410)
- Restricting PD FW download enable command to FW for SATA drives(SCGCQ01964173 port of SCGCQ01955389)
- Add security-related compilation and linker flags to StorCLI - Linux (SCGCQ01966163 port of SCGCQ01892560)
- Unified StorCLI : Enclosure devices are part of drive list used for drive operations (SCGCQ01982925 port of SCGCQ01979483)
- Unified LibMod changes : Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01985486 port of SCGCQ01893074)
- Enable iMR advanced debug dump(SCGCQ02035300 port of SCGCQ01873124)
- Drive Size Display Miss Match In Storcli Show Output (SCGCQ02074659 port of SCGCQ02072353)
- HDET:Libmods-Boot device should be presented as /dev/sda in Linux operating system during installation and post installation (SCGCQ02082198 port of SCGCQ02046182)
- HDET: Boot device should be presented as /dev/sda in Linux operating system during installation and post installation(SCGCQ02082199 port of SCGCQ02016712)
- BSOD observed when VD/JBOD Creation/Del and snapdump Cycles are initiated.(SCGCQ02085669 port of SCGCQ02045967)
- storclif /cx delete colinfo ? shows syntax error (SCGCQ02124654 port of SCGCQ02124492)
- PH12 PA - StorCLI /cx/pall show fails on 9400-8e board(SCGCQ02128167 port of SCGCQ02119004)
- Storcli: Force option not mentioned in "/cx/dx add mirror" and "/cx/vx start init" command.(SCGCQ02142248 port of SCGCQ02140878)
- Aero (DBU PA5):Storcli: No description of patrolread "OFF" and optional is mentioned as {}.(SCGCQ02145876 port of SCGCQ02140859)
- PERCCLI to support creation of VD with WB policy for PERC8 MR(SCGCQ01892550 port of SCGCQ01891650)
- MR: 64 Bit Utilities/Application to Support VMWARE ESXi 6.7+ (SCGCQ02139866 port of SCGCQ02066386)
- Libmod changes for SCGCQ02090770(SCGCQ02097658 port of SCGCQ02090770)
- Wide port info is not displayed under connector name for Backplane attached drives.(SCGCQ02085666 port of SCGCQ02076923)
- CLI returns wrong error code upon failure(SCGCQ02085528 port of SCGCQ02084966)
- MR_7.10_Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON output.(SCGCQ02079591 port of SCGCQ02018305)
- Storcli displays drive state as UBad instead of UBad (unsupported(SCGCQ02079521 port of SCGCQ02031615)
- Storcli: "resume migrate" command does not show syntax error.(SCGCQ02075292 port of SCGCQ02061340)
- BreakMirror RAID Support coming as Yes, even when Breakmirror is not supported(SCGCQ02075281 port of SCGCQ02048150)
- Drive Size Display Miss Match In Storcli Show Output (SCGCQ02075280 port of SCGCQ02072353)
- Typo in storcli /c0 set linkspeed help(SCGCQ02074664 port of SCGCQ02070951)
- PH11 Alpha - StorCLI - 'show file' command displays incorrect message after reading uploaded bios file(SCGCQ02064703 port of SCGCQ02063689)
- Storcli reported "Boot Volume Supported = NO" eventhough ctrl boot with OS on vd.(SCGCQ02047809 port of SCGCQ02030652)
- Storcli help file doesn't show recon rate command instead it shows migrate rate. (SCGCQ02047747 port of SCGCQ02046036)
- Storcli shows incorrect output for delete events command(SCGCQ02046875 port of SCGCQ02045816)
- Unified StorCLI : Enclosure devices are part of drive list used for drive operations (SCGCQ01979535 port of SCGCQ01979483)
- enhance warning message for personality switch indicating interruption could cause controller to be unstable(SCGCQ01892552 port of SCGCQ01892549)
- Storcli, should fail the command "get snapdump id=0 file=snapdump.zip norttdump" (SCGCQ01906745 port of SCGCQ01889700)
- StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911831 port of SCGCQ01886637)
- 6.13_SDS : Wrong error message is displayed on trying to create R0 vd on an pre configured drive as EPD.(SCGCQ01925211 port of SCGCQ01196785)
- Square bracket is missing in the syntax of "set hardware device page" in storclio.(SCGCQ01929137 port of SCGCQ01224857)
- For NVMe drive use the term NVMe instead of PCIe (SCGCQ01963960 port of SCGCQ01923119)
- StorCLI show SAS address for NVMe drives (SCGCQ01963964 port of SCGCQ01921258)
- JBOD list is not showing in order when using /cx show(SCGCQ01965193 port of SCGCQ01961527)
- Added Windows compiler security flags (SDL and control flow guard(SCGCQ01965209 port of SCGCQ01949495)
- supported personalities has blank value (SCGCQ01971366 port of SCGCQ01965370)
- Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01977028 port of SCGCQ01948579)
- Expander FW download using storecli utility crashs.(SCGCQ01979617 port of SCGCQ01979599)
- WBSup abbreviation defined twice when running perccli /cX show profile(SCGCQ01995022 port of SCGCQ01993282)
- spell mistake in start diag operation failure(SCGCQ01998963 port of SCGCQ01998330)
- Proper message to be given on VD creation with wb option while Battery not connected/Failed(SCGCQ02028787 port of SCGCQ01972504)
- iMR Changing profileid's using cli results in Status=Success Description=None(SCGCQ02028810 port of SCGCQ02008676)
- Enable iMR advanced debug dump(SCGCQ02035289 port of SCGCQ02030908)
- On Demand SnapDump does not show proper time stamp.(SCGCQ02085609 port of SCGCQ02084833)
- Flashing of Completeflash fails on Sea IT controller(SCGCQ02139848 port of SCGCQ02139780)
- Storcli: "Ctrl" legend not mentioned.(SCGCQ02150640 port of SCGCQ02146822)
- storcli -help missing the verbose option (SCGCQ02160908 port of SCGCQ02158600)
- MR7.11_Storcli: Incorrect error description while creating r1 with single drive(SCGCQ02168183 port of SCGCQ02165933)
- Phase 12 - Oct Huawei DET - Incorrect Phy Details Displayed for Ventura IT Controller(SCGCQ02179296 port of SCGCQ02174296)
- Incorrect Help Menu For "show phyerrorcounters"(SCGCQ02180519 port of SCGCQ02180495)
- Recon command (./storcli /cx set recon(SCGCQ02086570 port of SCGCQ02081415)
- Need a space between atleast with StorCLI error message "Unmap is not supported atleast on one device"(SCGCQ02075290 port of SCGCQ02064120)
- Show Snapdump help command lists delete snapdump details as well.(SCGCQ02075287 port of SCGCQ02064836)
- iMR Changing profileid's using cli results in Status=Success Description=None(SCGCQ02056156 port of SCGCQ02008676)
- Spell mistake on support ondemand snapdump property of show all output(SCGCQ02053926 port of SCGCQ02053923)
- Unified StorCLI : Individual SL_INIT_LIB calls are made for every SL command invocation(SCGCQ02047893 port of SCGCQ02047100)
- Instance Validation Failed between "drive-group-hidden-schema" and "/c1/dall set hidden" & "set security"(SCGCQ02047136 port of SCGCQ02040779)
- unmap attribute is not mentioned in help file command "add vd each r0".(SCGCQ02047095 port of SCGCQ02042106)
- Storcli pop-up a message "controller not found" during chip reset , rather than controller busy. (SCGCQ02047079 port of SCGCQ02024740)
- Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ02009900 port of SCGCQ01761309)
- storcli faults for enclosure show command(SCGCQ01986423 port of SCGCQ01985815)
- storclio command not working to update FW on SATA disk(SCGCQ01922919 port of SCGCQ01918814)
- Restricting PD FW download enable command to FW for SATA drives(SCGCQ01964153 port of SCGCQ01955389)
- StorCLI crashes, while trying to enable security on any DG ,incase, when no DG exists(SCGCQ01965185 port of SCGCQ01413253)
- Added Windows compiler security flags (SDL and control flow guard(SCGCQ01965210 port of SCGCQ01949503)
- Unified LibMod changes : Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01966261 port of SCGCQ01893074)
- Add security-related compilation and linker flags to StorCLI - Linux (SCGCQ01985558 port of SCGCQ01892560)
- Snapdump unsupported commands for HPE needs to be disabled(SCGCQ01996375 port of SCGCQ01985589)
- MR_7.9: Storcli reported unknown OS for Windows 10 RS5 LTSC.(SCGCQ02009848 port of SCGCQ01992461)
- Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ02011417 port of SCGCQ01761309)
- StorcliO show oob command fails for Invader based cards(SCGCQ02043788 port of SCGCQ02040783)
- Storclif doesn't show details for VF/PF in help file for vfmap command .(SCGCQ02124488 port of SCGCQ02123789)
- Storcli: "completeflash" is listed in Windows help file.(SCGCQ02145743 port of SCGCQ02141931)
- Storcli: /c0 set ? lists bbu,mx,px and lnx commands. (SCGCQ02145756 port of SCGCQ02136689)
- Configuring multiple lane speed is working only for fisrt ID, Rest were ignored(SCGCQ02145764 port of SCGCQ02136333)
- Help note 'page=[x]' needs update(SCGCQ02149062 port of SCGCQ02146823)
- Instance Validation Failed for "/call/eall show status extended" and enclosure-status-extended-schema.json(SCGCQ02153948 port of SCGCQ02150924)
- Instance Validation Failed for /call/show_all.json and controller-detailed-properties-schema.json(SCGCQ02154721 port of SCGCQ02135526)
- StorCLI listing PD Slot Status as "Incorrect Status Value" for configured PD's(SCGCQ02097676 port of SCGCQ02090770)
- Aero (DBU PA2(SCGCQ02086670 port of SCGCQ02082460)
- storclif.exe /c0/ex/sx show poh should show proper message during command execution.(SCGCQ02086632 port of SCGCQ02075242)
- show/set lane speed shows success when we are in SAS profile(SCGCQ02079507 port of SCGCQ02078437)
- Storcli: "show config" command shown as Un-supported.(SCGCQ02075286 port of SCGCQ02064839)
- Schema file updates for controller show all output change for defect SCGCQ02048150(SCGCQ02075282 port of SCGCQ02069817)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for "/cx get vpd" commands.(SCGCQ02058567 port of SCGCQ02018140)
- Instance Validation Failed between "vd-unmap-schema.json" and "/call/vall show unmap"(SCGCQ02047243 port of SCGCQ02035370)
- Instance Validation Failed between "drive-group-schema.json" and "/call/dall show " and /call/dall show all (SCGCQ02047235 port of SCGCQ02040756)
- PH11 PA - StorCLI - Segmentation fault seen when 'compare linkspeed' executed on Fury C0 board(SCGCQ02044794 port of SCGCQ02044777)
- Request to Disable DSW3(SCGCQ01903331 port of SCGCQ01896311)
- PERCCLI Support for EKMS(SCGCQ01904188 port of SCGCQ01902150)
- StorCLI crashes, while trying to enable security on any DG ,incase, when no DG exists(SCGCQ01904340 port of SCGCQ01413253)
- Disk performance throttled when running MegaCli AdpEvent log dump on Aspen and Vail (Invader and Intruder(SCGCQ01921529 port of SCGCQ01220901)
- Hide "set termlog" help contents from perccli(SCGCQ01935143 port of SCGCQ01923643)
- Storcli is not showing foreign configs if user has SED drive which is in foreign(SCGCQ01940869 port of SCGCQ01937410)
- Storcli not working on large config setup when some of the drives are missing or the system has foreign config.(SCGCQ01945534 port of SCGCQ01940805)
- Storcli- Delay seen in /c0 /vall show all o/p(SCGCQ01965393 port of SCGCQ01935697)
- Storcli shows wrong PD list sequence.(SCGCQ01971632 port of SCGCQ01967488)
- LD size not shown in GiB format in foreign import preview(SCGCQ01996370 port of SCGCQ01978978)
- Unable to switch to eHBA mode using a H745P Adapter(SCGCQ01998964 port of SCGCQ01990060)
- perccli show profile lists personality as JBOD instead of eHBA(SCGCQ01998966 port of SCGCQ01998328)
- Json Schema for the command "storcli /cx/ex show phyerrorcounters" needs to be updated(SCGCQ02101377 port of SCGCQ02101372)
- In ARM server UEFI shell, storcli.efi hangs forever when storcliconf.ini is present(SCGCQ02116733 port of SCGCQ02115036)
- complete Lane WWID is not displayed(SCGCQ02145739 port of SCGCQ02145716)
- No "Rbld" legend during rebuild. (SCGCQ02150634 port of SCGCQ02146819)
- Error message mismatch is seen for rttdump command on iMR Ventura controller.(SCGCQ02160907 port of SCGCQ02156483)
- Storcli throws different error messages for show status command in Ventura and Aero(SCGCQ02086689 port of SCGCQ02078409)
- Multiple status messages are displayed in the output (SCGCQ02086536 port of SCGCQ02073042)
- MR_7.10_Storcli: No schema file for controller sesmultipathcfg commands.(SCGCQ02079595 port of SCGCQ02018134)
- MR_7.10_Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" JSON output.(SCGCQ02079590 port of SCGCQ02018277)
- "Run time to empty" field showing as "Battery is not being charged" when the battery is being charged.(SCGCQ02079535 port of SCGCQ02045324)
- MR_7.10_Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set personality" JSON output.(SCGCQ02050491 port of SCGCQ02016762)
- MR_7.10_Storcli: Add VD command output is not in JSON format.(SCGCQ02050489 port of SCGCQ02034493)
- "Invalid RAID level" error message while creating R10 VD.(SCGCQ02047806 port of SCGCQ02034471)
- Incorrect status displayed for pause rebuild command.(SCGCQ02046878 port of SCGCQ02043610)
- PH11 PA Storcli: Incorrect error message shown while programming invalid sasaddress(SCGCQ02043612 port of SCGCQ02042296)
- Aero UTP: storclif /call show commands output contains "Count 4 exceeded for token id #" (SCGCQ02034200 port of SCGCQ02034064)
- Storcli shows wrong PD list sequence.(SCGCQ01977461 port of SCGCQ01967488)
- Migrate Failure case is not Branding compliant(SCGCQ02000716 port of SCGCQ01988402)
- StorCLI PH12: Retrieving topology details causes application crash in some scenario(SCGCQ02106192 port of SCGCQ02103217)
- Support FMP Images in UEFI Version of PERCCli(SCGCQ02116464 port of SCGCQ02078649)
- MR 7.11: Storcli.efi: On ARM server, incomplete configuration data received error is observed for any storcli.efi command(SCGCQ02116497 port of SCGCQ02114898)
- PH12 PA - StorCLI - 9310-8i IR FW download fails (SCGCQ02121848 port of SCGCQ02121783)
- LibMod changes : MR: 64 Bit Utilities/Application to Support VMWARE ESXi 6.7+(SCGCQ02139867 port of SCGCQ02085102)
- MR7.11_Storcli: On drive rebuild, there is a mismatch between the pd rebuild state and respective legend (SCGCQ02168256 port of SCGCQ02165944)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for /cx/px commands.(SCGCQ02079604 port of SCGCQ02018137)
- MR_7.10_Storcli: Instance Validation Failed between "controller-patrolread-schema.json" and "/call pause patrolread"(SCGCQ02079597 port of SCGCQ02035437)
- Empty data is listed when we query for show linkconfig(SCGCQ02079511 port of SCGCQ02076931)
- Libmods: show.set lane speed shows success with wrong data when we are in SAS profile(SCGCQ02079506 port of SCGCQ02078513)
- Incorrect status displayed for resume copyback command. (SCGCQ02075291 port of SCGCQ02062834)
- "Delete snapdump" command shows same description "Snapdump clear" for success and failure case.(SCGCQ02075284 port of SCGCQ02065734)
- MR_7.10_Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/eall/sall show all"(SCGCQ02050481 port of SCGCQ02018327)
- Libmod changes: Adding CLI command to display/toggle new controller property.(SCGCQ01106982(SCGCQ01929892 port of SCGCQ01106988)
- Added new commands from StorCLI(SCGCQ01935296 port of SCGCQ01134166)
- For NVMe drive use the term NVMe instead of PCIe (SCGCQ01964024 port of SCGCQ01923119)
- securesed autoconfig param should not be present for perccli help(SCGCQ01986879 port of SCGCQ01986831)
- Extend major downgrade support in storCLI for SAS3 IT product(SCGCQ02032582 port of SCGCQ02029410)
- Drives connected to active backplanes not showing the phy info in connector name (SCGCQ02112425 port of SCGCQ02112424)
- Background operations keep on progressing after hitting /c0 shutdown from storcli(SCGCQ02150630 port of SCGCQ02132024)
- Instance Validation Failed for "/call/eall show status" and enclosure-status-schema.json(SCGCQ02153950 port of SCGCQ02150921)
- Instance Validation Failed for "/call/cv show all" and cache-vault-detailed-schema.json(SCGCQ02154755 port of SCGCQ02150651)
- Storcli: Force is mentioned as optional in snapdump delete command.(SCGCQ02086544 port of SCGCQ02083822)
- Port information is not displayed for Vses Backplane (SCGCQ02085875 port of SCGCQ02053070)
- MR_7.9: Storcli reported unknown OS for Windows 10 RS5 LTSC. (SCGCQ02079601 port of SCGCQ01992461)
- spell mistake in start diag operation failure(SCGCQ02079529 port of SCGCQ01998330)
- Storcli:"resource already in use" error message displayed when trying to create VD with one UG and one UBUnsp.(SCGCQ02075289 port of SCGCQ02064828)
- Storcli: HPE serial number programming and display(SCGCQ02062635 port of SCGCQ01882984)
- MR_7.10_Storcli: Instance Validation Failed between "cache-vault-detailed-schema.json" and "/call/cv show all "(SCGCQ02050460 port of SCGCQ02019729)
- FW flash fails to load the latest image after upgrade downgrade with resetnow option (SCGCQ02046879 port of SCGCQ02035152)
- Extend major downgrade support in storCLI for SAS3 IT product(SCGCQ02032581 port of SCGCQ02029410)
- Storcli throws an 'Incomplete foreign configuration' error when there is no enclosure connected(SCGCQ02007109 port of SCGCQ02006450)
- Storcli issuing 'add jbod drives=all' causes storcli to crash(SCGCQ01893381 port of SCGCQ01892288)
- LibMods : Adding the function that changing flag of full initialize completion(SCGCQ01930028 port of SCGCQ01141462)
- Storcli- Delay seen in /c0 /vall show all o/p(SCGCQ01936895 port of SCGCQ01935697)
- Terminology change from " Data protection" to " Data integrity".(SCGCQ01940807 port of SCGCQ01827339)
- Libmods: Terminology change from " Data protection" to " Data integrity".(SCGCQ01943370 port of SCGCQ01827732)
- Incorrect colinfo output of Bad block count(SCGCQ01977457 port of SCGCQ01977443)
- StorCLI hangs when viewing controller in FreeBSD (MR7.8 is okay(SCGCQ01984543 port of SCGCQ01978824)
- Unified StorCLI : Help command of "Get flash" is not shown in generic help syntax(SCGCQ01985472 port of SCGCQ01985463)
- StorCLI show output shows Legends as BBU instead of EnergyPack.(SCGCQ01992007 port of SCGCQ01985587)
- Aero A0 UTP: StorCLI snapdump command needs to clarify new "On Demand" snapdump option(SCGCQ01995066 port of SCGCQ01993722)
- Shenandoah:StorCLI:Right click properties for released binary shown blank.(SCGCQ02000843 port of SCGCQ01988329)
- Smart Carrier Enclosure port info shown as "Multuipath"(SCGCQ02008273 port of SCGCQ01992087)
- MR 7.11: Storcli: Instance Validation Failed for "/call show all" and system-schema.json (SCGCQ02116771 port of SCGCQ02112192)
- "Storcli /c# set jbod=on" shows success but does nothing (SCGCQ02119067 port of SCGCQ02117219)
- Phyreset Fails on IT controllers (SCGCQ02169305 port of SCGCQ02169242)
- Storcli stop erase needs an help file update (SCGCQ02169308 port of SCGCQ02168895)
- Updating phy link reset logic for IT cards with respect to storelib changes(SCGCQ02185911 port of SCGCQ02184862)
- Storcli connector display not matching with Aero board 9560-16i. (SCGCQ02085681 port of SCGCQ02072448)
- MR_7.10_Storcli: controller-detailed-properties-schema.json or "/call show all " output not in JSON format(SCGCQ02079610 port of SCGCQ02016771)
- MR_7.10_Storcli: No schema file for controller unmap commands.(SCGCQ02079593 port of SCGCQ02016749)
- Incorrect error message displayed while creating R10 VD when no free space available.(SCGCQ02075283 port of SCGCQ02067575)
- remove the maxconcurrentpd check from storcli and report fw returned failure (SCGCQ02053931 port of SCGCQ02053910)
- PERCCLI Support for EKMS (SCGCQ01904189 port of SCGCQ01903448)
- StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911832 port of SCGCQ01886637)
- Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder(SCGCQ01915313 port of SCGCQ01222855)
- (Libmods) Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder)(SCGCQ01915315 port of SCGCQ01227144)
- perccli /c0 show all lists topology without any DG's present(SCGCQ01998965 port of SCGCQ01998332)
- PH12 PA - StorCLI version not getting printed for show file command (SCGCQ02116759 port of SCGCQ02105185)
- Convention comes in same line while performing help for /c0/e0/s0 download.(SCGCQ02176697 port of SCGCQ02176681)
- With IT controller for set or reset with invalid phy is not showing error(SCGCQ02183510 port of SCGCQ02181823)
EnhancementRequests:
- Incorporating VMware constraints for PERCCLI VIB signing (SCGCQ02190441)
- Migrating VMware 64 bit toolchain to 6.8.7-13394445(SCGCQ02190429)
- Create an event for DDF config clear failed event.(SCGCQ02173513)
- (SCGCQ02162699)
- Snap Dump ClearAll Method logging event(SCGCQ02157359)
- API changes for a better presentation of Atlas to tools(SCGCQ02149380)
- Add disableOffloadNum field in MR_SNAPDUMP_PROPERTIES struct(SCGCQ02125252)
- Better error message for certain unmap operations(SCGCQ02111563)
- Add MFI STAT and MR Event for Secure Boot indicating fw dl was not allowed due to an existing pending key change(SCGCQ02103973)
- MR Windows IOCTL Error codes to Application added to MR API(SCGCQ02103183)
- API changes for linkconfig interface (SCGCQ02053671)
- API changes for NVMe speed and width changes (SCGCQ02053667)
- Reword event log messages as it creates unnecessary panic.(SCGCQ02013675)
- Added Windows compiler security flags (SDL and control flow guard(SCGCQ01949495)
- Unified StorCLI : Adding component level download functionality to StorCLI(SCGCQ01940030)
- show complete Serial Number and Model Name for NVMe drive(SCGCQ01927541)
- snapdump support for host initiated snapdump (SCGCQ01901158)
- Changes for disable least latency mode(SCGCQ01891451)
- Inspur request to add to show smart info of sas drive for "StorCLI /cx/ex/sx show smart" command(SCGCQ01929656)
- MR_SAS_Unified_Libmods_7.10 Inspur request to add to show smart info of sas drive for "StorCLI /cx/ex/sx show smart" command(SCGCQ01979597)
- Post firmware trace buffer at the time of driver load(SCGCQ01992779)
- Adding the spare details in the same volume creation(CONFIG_ADD DCMD(SCGCQ02008407)
- PSoC implementation in StorCLI by parsing PSoC image(SCGCQ02072160)
- Request to display the help for "show" and "set" for JBOD in PercCLI (SCGCQ02160291)
- Adding NVACHE messages indicate when SLC format has started and completed.(SCGCQ02137048)
- MR API: Add support bits for currentSpeed and clkMode(SCGCQ02132334)
- Enable iMR advanced debug dump(SCGCQ02030908)
- Unified StorCLI : ARM Windows support to StorCLI(SCGCQ01962294)
- Disabling RAID00 support (SCGCQ01960420)
- HPE Shenandoah: Branding tool(SCGCQ01960295)
- Added Windows compiler security flags (SDL and control flow guard(SCGCQ01949503)
- Unified StorCLI : Allow SBR/SPD read and write using new CBB+SBR concatenated image(SCGCQ01927551)
- show complete Serial Number and Model Name for NVMe drive connected to IT controller(SCGCQ01927538)
- show complete Serial Number and Model Name for NVMe drive(SCGCQ01919655)
- Unified CLI - Command processor changes for handling invalid/tampered device id's for sea IT controllers(SCGCQ01891513)
- Add support to display PSOC version for Ventura IT controllers(SCGCQ02067300)
- set copyback command changes for cli(SCGCQ02148092)
- Unified StorCLI : ARM64 Windows support to StorCLI - LibMod changes(SCGCQ01963208)
- Shenandoah: Adding support bit check for delete snap dump(SCGCQ01944500)
- Enable iMR advanced debug dump(SCGCQ01873124)
- Unified StorCLI : PSoC read and write via Device read and write DCMD's in MR Operational case(SCGCQ01949521)
- Changes for disable least latency mode(SCGCQ01891442)
- Adding the spare details in the same volume creation (CONFIG_ADD DCMD(SCGCQ02008403)
- Unified StorCLI : Allow erase functionality on operational MR using CBB concatenated image(SCGCQ01927595)
- Unified CLI : Handling invalid/tampered controllers for sea controllers(SCGCQ01891484)
- Requesting StorCLIF to read MR FW from flash device and write it to a file. Similar to what IT FW support.(SCGCQ01631948)
- Add ability to field upgrade PSOC on HBA boards(SCGCQ01583214)
- DUal Image SUpport(SCGCQ01960287)
- Libmods: Porting HPE Shenandoah from Aero to 7.9 (SCGCQ01917263)
- Porting HPE Shenandoah from Aero to 7.9(SCGCQ01917172)
- Adding HPE specific help for storcli (SCGCQ01935699)
007.0816.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
defects:
- Improve Debuggablity for MegaRAID Windows Driver by Adding RT Trace - new modifications(SCGCQ01824574 port of SCGCQ01824569)
- displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state"(SCGCQ01827604 port of SCGCQ01681538)
- Updating makefile and EFI's INF changes for ARM StorCLIO(SCGCQ01870684 port of SCGCQ01563125)
- Square bracket is missing in the syntax of "set hardware device page" in storclio.(SCGCQ01929787 port of SCGCQ01224857)
- failure in StorCLI enclosure show status (SCGCQ02043616 port of SCGCQ02040640)
- MR_7.10_Storcli: Instance Validation Failed between "virtual-drive-detailed-schema.json" and "/call/vall show all "(SCGCQ02050471 port of SCGCQ02018333)
- MR_7.10_Storcli: unmap attribute is not mentioned in "/c0 add vd" command syntax in Schema_mapping_list.xlsx file.(SCGCQ02050535 port of SCGCQ02016758)
- Aero DBU PA1:Storcli: Instance Validation Failed "controller-properties-schema" and "/call show" command.(SCGCQ02061387 port of SCGCQ02035439)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for drive jbod commands.(SCGCQ02079592 port of SCGCQ02018135)
- MR_7.10_Storcli: bbu-show-modes-schema.json file is not in JSON format.(SCGCQ02079618 port of SCGCQ02019740)
- perccli /c0 show all lists topology without any DG's present(SCGCQ02085925 port of SCGCQ01998332)
- Libmod changes for StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers(SCGCQ01853370 port of SCGCQ01775616)
- (SCGCQ01775602 port of SCGCQ01814011)
- show enclosure command is not exiting to shell(SCGCQ01874899 port of SCGCQ01814011)
- StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911831 port of SCGCQ01886637)
- Storcli shows incorrect output for delete events command (SCGCQ02046875 port of SCGCQ02045816)
- Storcli help file doesn't show recon rate command instead it shows migrate rate.(SCGCQ02047747 port of SCGCQ02046036)
- Storcli reported "Boot Volume Supported = NO" eventhough ctrl boot with OS on vd.(SCGCQ02047809 port of SCGCQ02030652)
- PH11 Alpha - StorCLI - 'show file' command displays incorrect message after reading uploaded bios file(SCGCQ02064703 port of SCGCQ02063689)
- Typo in storcli /c0 set linkspeed help(SCGCQ02074664 port of SCGCQ02070951)
- Drive Size Display Miss Match In Storcli Show Output(SCGCQ02075280 port of SCGCQ02072353)
- BreakMirror RAID Support coming as Yes, even when Breakmirror is not supported(SCGCQ02075281 port of SCGCQ02048150)
- Storcli: "resume migrate" command does not show syntax error.(SCGCQ02075292 port of SCGCQ02061340)
- Storcli displays drive state as UBad instead of UBad (unsupported(SCGCQ02079521 port of SCGCQ02031615)
- MR_7.10_Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON output.(SCGCQ02079591 port of SCGCQ02018305)
- CLI returns wrong error code upon failure(SCGCQ02085528 port of SCGCQ02084966)
- Wide port info is not displayed under connector name for Backplane attached drives.(SCGCQ02085666 port of SCGCQ02076923)
- Libmod changes for SCGCQ02090770 (SCGCQ02097658 port of SCGCQ02096774)
- Hide/Unhide command output display incorrect VD no for VDs on which the operation is not supported(SCGCQ01850374 port of SCGCQ01837932)
- Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ02009900 port of SCGCQ01761309)
- Storcli pop-up a message "controller not found" during chip reset , rather than controller busy.(SCGCQ02047079 port of SCGCQ02024740)
- unmap attribute is not mentioned in help file command "add vd each r0".(SCGCQ02047095 port of SCGCQ02042106)
- Instance Validation Failed between "drive-group-hidden-schema" and "/c1/dall set hidden" & "set security"(SCGCQ02047136 port of SCGCQ02040779)
- Unified StorCLI : Individual SL_INIT_LIB calls are made for every SL command invocation(SCGCQ02047893 port of SCGCQ02047100)
- Spell mistake on support ondemand snapdump property of show all output(SCGCQ02053926 port of SCGCQ02053923)
- iMR Changing profileid's using cli results in Status=Success Description=None(SCGCQ02056156 port of SCGCQ02008676)
- Show Snapdump help command lists delete snapdump details as well.(SCGCQ02075287 port of SCGCQ02064836)
- Need a space between atleast with StorCLI error message "Unmap is not supported atleast on one device"(SCGCQ02075290 port of SCGCQ02064120)
- Recon command (./storcli /cx set recon(SCGCQ02086570 port of SCGCQ02081415)
- Enhance the detailed help for Firmware download and get bios command.(SCGCQ01792109 port of SCGCQ01790167)
- PH11 PA - StorCLI - Segmentation fault seen when 'compare linkspeed' executed on Fury C0 board(SCGCQ02044794 port of SCGCQ02044777)
- Instance Validation Failed between "drive-group-schema.json" and "/call/dall show " and /call/dall show all(SCGCQ02047235 port of SCGCQ02040756)
- Instance Validation Failed between "vd-unmap-schema.json" and "/call/vall show unmap"(SCGCQ02047243 port of SCGCQ02035370)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for "/cx get vpd" commands.(SCGCQ02058567 port of SCGCQ02018140)
- Schema file updates for controller show all output change for defect SCGCQ02048150(SCGCQ02075282 port of SCGCQ02069817)
- Storcli: "show config" command shown as Un-supported.(SCGCQ02075286 port of SCGCQ02064839)
- show/set lane speed shows success when we are in SAS profile (SCGCQ02079507 port of SCGCQ02078437)
- storclif.exe /c0/ex/sx show poh should show proper message during command execution.(SCGCQ02086632 port of SCGCQ02075242)
- Aero (DBU PA2)(SCGCQ02086670 port of SCGCQ02082460)
- StorCLI listing PD Slot Status as "Incorrect Status Value" for configured PD's(SCGCQ02097676 port of SCGCQ02090770)
- Error message when Maximum number of VDs are reached (SCGCQ01857450 port of SCGCQ01856544)
- Aero UTP: storclif /call show commands output contains "Count 4 exceeded for token id #" (SCGCQ02034200 port of SCGCQ02034064)
- PH11 PA Storcli: Incorrect error message shown while programming invalid sasaddress(SCGCQ02043612 port of SCGCQ02042296)
- Incorrect status displayed for pause rebuild command.(SCGCQ02046878 port of SCGCQ02043610)
- "Invalid RAID level" error message while creating R10 VD.(SCGCQ02047806 port of SCGCQ02034471)
- MR_7.10_Storcli: Add VD command output is not in JSON format.(SCGCQ02050489 port of SCGCQ02034493)
- MR_7.10_Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set personality" JSON output.(SCGCQ02050491 port of SCGCQ02016762)
- "Run time to empty" field showing as "Battery is not being charged" when the battery is being charged.(SCGCQ02079535 port of SCGCQ02045324)
- MR_7.10_Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" JSON output.(SCGCQ02079590 port of SCGCQ02018277)
- MR_7.10_Storcli: No schema file for controller sesmultipathcfg commands.(SCGCQ02079595 port of SCGCQ02018134)
- Multiple status messages are displayed in the output (SCGCQ02086536 port of SCGCQ02073042)
- Storcli throws different error messages for show status command in Ventura and Aero(SCGCQ02086689 port of SCGCQ02078409)
- Improve Debuggablity for MegaRAID Windows Driver by Adding RT Trace - new modifications(SCGCQ01825986 port of SCGCQ01824570)
- Turn on the boodrive by storcli, HII does not reflect it, still shows "Off"(SCGCQ01832791 port of SCGCQ01816927)
- Add interface in storecli that could get relearn complete status (SCGCQ01850373 port of SCGCQ01848387)
- MR_7.10_Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/ eall/sall show all"(SCGCQ02050481 port of SCGCQ02018327)
- "Delete snapdump" command shows same description "Snapdump clear" for success and failure case.(SCGCQ02075284 port of SCGCQ02065734)
- Incorrect status displayed for resume copyback command.(SCGCQ02075291 port of SCGCQ02062834)
- Libmods: show.set lane speed shows success with wrong data when we are in SAS profile(SCGCQ02079506 port of SCGCQ02078513)
- Empty data is listed when we query for show linkconfig(SCGCQ02079511 port of SCGCQ02076931)
- MR_7.10_Storcli: Instance Validation Failed between "controller-patrolread-schema.json" and "/call pause patrolread" (SCGCQ02079597 port of SCGCQ02035437)
- MR_7.10_Storcli: No "schema and command" mapping details in Schema_mapping_list.xlsx file for /cx/ px commands.(SCGCQ02079604 port of SCGCQ02018137)
- Aero - LibMod changes for ER SCGCQ01813156 : Addition of Aero and Sea device id's and checkwords (SCGCQ01853418 port of SCGCQ01813626)
- Storcli throws an 'Incomplete foreign configuration' error when there is no enclosure connected(SCGCQ02007109 port of SCGCQ02006450)
- Extend major downgrade support in storCLI for SAS3 IT product(SCGCQ02032581 port of SCGCQ02029410)
- FW flash fails to load the latest image after upgrade downgrade with resetnow option (SCGCQ02046879 port of SCGCQ02035152)
- MR_7.10_Storcli: Instance Validation Failed between "cache-vault-detailed-schema.json" and "/call/cv show all "(SCGCQ02050460 port of SCGCQ02019729)
- Storcli:"resource already in use" error message displayed when trying to create VD with one UG and one UBUnsp.(SCGCQ02075289 port of SCGCQ02064828)
- spell mistake in start diag operation failure(SCGCQ02079529 port of SCGCQ01998330)
- MR_7.9: Storcli reported unknown OS for Windows 10 RS5 LTSC.(SCGCQ02079601 port of SCGCQ01992461)
- Port information is not displayed for Vses Backplane (SCGCQ02085875 port of SCGCQ02053070)
- Storcli: Force is mentioned as optional in snapdump delete command.(SCGCQ02086544 port of SCGCQ02083822)
- Add get VPD command support to StorCLI in OS environment (SCGCQ01855067 port of SCGCQ01852603)
- Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01977760 port of SCGCQ01948579)
- CSET: Checking in Libmod changes for defect SCGCQ02030652 - (SCGCQ02045948(SCGCQ02047884 port of )
- remove the maxconcurrentpd check from storcli and report fw returned failure (SCGCQ02053931 port of SCGCQ02053910)
- Incorrect error message displayed while creating R10 VD when no free space available.(SCGCQ02075283 port of SCGCQ02067575)
- MR_7.10_Storcli: No schema file for controller unmap commands.(SCGCQ02079593 port of SCGCQ02016749)
- MR_7.10_Storcli: controller-detailed-properties-schema.json or "/call show all " output not in JSON format(SCGCQ02079610 port of SCGCQ02016771)
- Storcli connector display not matching with Aero board 9560-16i.(SCGCQ02085681 port of SCGCQ02072448)
EnhancementRequest:
- Updating ncurses library from 6.0 to 6.1(SCGCQ01836749)
- Command processor changes for Secure boot properties feature - SCGCQ01855473 (SCGCQ01855503)
- Adding secure boot properties to unified StorCLI (SCGCQ01855473)
- Adding new MFI STAT - MFI_STAT_SECURE_BOOT_KEY_SLOTS_FULL 007.0711.0000.0000 for Lenovo(SCGCQ01865190)
007.0713.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
- Storcli returns error for show file commands when parsing MR images eventhough the command was successful(SCGCQ01529009)
- "Cached Virtual Drives" displayed in /c0/dall show cachecade without the table.(SCGCQ01537017)
- storcli /c0 set sasaddhi =xxxx sasaddlow =xxxx displays incomplete sasaddress(SCGCQ01540807)
- storcli controller show all lists EPD's in VD list(SCGCQ01556595)
- controller show all command is not listing the Battery information(SCGCQ01561689)
- Commands "/call/all" return inappropriate message or segfault when both MR and IT controllers are connected(SCGCQ01561703)
- Instance Validation Failed between "vd-operations-migrate-schema.json" and "start migrate" JSON output.(SCGCQ01571207)
- Storcli: drive-group-security-schema.json is not present in the JSON Schema folder(SCGCQ01571280)
- Storcli: Instance Validation Failed between "drive_group_mirror_schema.json" and "/call/dall add mirror src=0" JSON output.(SCGCQ01571298)
- Instance Validation Failed "foreign-configuration-detailed-schema.json" and "/call/fall import preview" JSON output(SCGCQ01571393)
- "drive-power-on-schema.json" is named as "drive-get-power-on-schema.json" in "Schema_mapping_list" file.(SCGCQ01573229)
- Get VPD from MPB region is failure, but overalll status shows success(SCGCQ01589618)
- BBU-show-schema is not present in the schema mapping list, the list needs to be sorted to remove duplicate commands.(SCGCQ01599473)
- Coverity defect fixes for Uninitialized Variables, resource leaks(SCGCQ01600257)
- Spell mistake in error message for hwdev command(SCGCQ01614972)
- Coverity defect fix for itctflash file(SCGCQ01616369)
- Fixing coverity issues - Resource leaks - Part 5(SCGCQ01627961)
- Fixing coverity issues - Non array deletes - Part 6(SCGCQ01629478)
- CLI help does not reflect the new command to create an ePD(SCGCQ01639583)
- ModeE drive fw download not working when drive image is more than 32K(SCGCQ01681086)
- Space need in the output for Deprecated command in storclif64.exe when legacy Cli command is used(SCGCQ01687653)
- Grammatical mistakes in Perccli Un-supported RAID level warning message.(SCGCQ01714033)
- storclif /c0 start diag type=0, gives syntax error(SCGCQ01714663)
- Correcting the grammatical errors in firmware's MFI Stat messages(SCGCQ01717315)
- Unified StorCLI 7.7 : Unconfigured BAD drives are not displayed in /c0 show output(SCGCQ01718269)
- MR 7.7 - Storcli throws an incorrect error msg while importing foreign config from Raid to JBOD mode.(SCGCQ01718981)
- Unmap property is not displayed for a drive in drive show all command output(SCGCQ01720959)
- Unified StorCLI 7.7 : StorCLI should allow noreset option when current NVDATA is lesser than the new NVDATA for SAS3.5 IT(SCGCQ01727159)
- Enclosure show status command gives success but nothing is shown(SCGCQ01731280)
- Unified StorCLI 7.7 : StorCLI doesn't report failure status when nopad image flashing fails via completeflash command in MR(SCGCQ01749849)
- Help content for jbodx show unmap is not present(SCGCQ01790130)
- One of the requirement for Criteo is to display JBOD-WB (EPD) to OS drive mapping.(SCGCQ01804763)
- Turn on the boodrive by storcli, HII does not reflect it, still shows "Off"(SCGCQ01816927)
- Incorrect Interface Details for "storcli /c0 show" command(SCGCQ01837612)
- MR API - Incorrect value used for MR_DCMD_CTRL_SNAPDUMP_ONDEMAND(SCGCQ01882581)
- storclio command not working to update FW on SATA disk(SCGCQ01918814)
- Storcli- Delay seen in /c0 /vall show all o/p(SCGCQ01935697)
- Phase3 Beta PCIe: Loading SLOOB fails with error message "ExitLib failed for SAS IT Controller!! rval 0x801A"(SCGCQ01292964)
- storcli /cx/pall show command fails with older generation cards that does not support PCIe pages(SCGCQ01520816)
- Storcli: vd-delete-schema.json is not present in the JSON Schema folder(SCGCQ01571254)
- Instance Validation Failed between "controller-properties-schema.json" and "/call show" JSON output.(SCGCQ01573076)
- Unified LibMods : Fixing coverity issues - Resource leaks and Uninitialized variables - Part 2(SCGCQ01600381)
- Unified LibMods : Coverity fixes for uninitialized variables in File functions - Part 4(SCGCQ01606830)
- Checking in VBAS compliation changes(SCGCQ01630324)
- PERCCLI ePD personality behavior command is still an available option and has not been removed(SCGCQ01639798)
- Instance Validation Failed "system-schema.json" and "storcli64.exe show all" JSON output.(SCGCQ01640825)
- Storcli: VD creation fails from storcli in presence of 0KB bad drive .(SCGCQ01713240)
- Space need in the output for secure erase(SCGCQ01713604)
- PA2-MR7.7-StorCLI: "storcli /c0/v239 start migrate type=raid0 option=add drives=66:18" gives syntax error(SCGCQ01713681)
- Drive Listing Is Not In Order for "/c0 show" & "/c0/eall/sall show"(SCGCQ01714356)
- StorCLI 7.702 help for SnapDump is not clear(SCGCQ01715025)
- IT Fw Download command StorCLI /c0/eall/sall hang(SCGCQ01723226)
- Unified StorCLI Phase 8 : No help section for ForceHCB option(SCGCQ01731292)
- Unified CLI 7.7 : Fixing coverity issues - Resource leaks,Unused variables,and non-array deletes - Part 1(SCGCQ01732959)
- Unified StorCLI Phase 8 : Firmware downgrade should be supported only by StorCLIO for SAS3 IT controllers(SCGCQ01734559)
- Storcli does not display the complete enclosure serial number(SCGCQ01735493)
- Storcli vib update fails across releases.(SCGCQ01761795)
- StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers(SCGCQ01775602)
- StorCLI enable/disable unmap VDs return status as failed instead of successful(SCGCQ01803306)
- Removing the set/show of unmap on JBOD.(SCGCQ01817855)
- Unified StorCLI 7.6 : Read SBR fails with pre-ventura controllers(SCGCQ01539360)
- Storcli: Instance Validation Failed between "drive-group-detailed-schema.json" and "/call/dall show all" JSON output.(SCGCQ01571287)
- Instance Validation Failed between "foreign-configuration-schema.json" and "/call/fall show" JSON output.(SCGCQ01571391)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "/call show all" JSON output.(SCGCQ01573096)
- "drive-security-key-schema.json" is named as "drive-securitykey-schema.json" in "Schema_mapping_list" file.(SCGCQ01573226)
- CLI does not report Serial number for Enclosure.(SCGCQ01595640)
- Json schema for enclosure phyerrorcounters has not been added, output format needs modification.(SCGCQ01595673)
- Unified StorCLI 7.7 : SAS Phyloopback test reports false positive results(SCGCQ01624063)
- Update help contents for jbod delete(SCGCQ01624605)
- Drive download commands help syntax to be updated for IT.(SCGCQ01681089)
- Grammatical error in Perccli warning message during FW Flash.(SCGCQ01686670)
- Missing punctuation in Perccli delete config message(SCGCQ01698226)
- Personality Behavior Modes:Command returns failure when setting non-RAID behavior modes.(SCGCQ01713265)
- Unified StorCLI Phase 8 : NVMe and SAS Drive's WWN is incorrect for IT Controller(SCGCQ01749795)
- Storcli is not showing foreign configs if user has SED drive which is in foreign(SCGCQ01937410)
- controller show wbsupport reason is not listed in the cli output(SCGCQ01561704)
- Application crashes while executing storcli64.exe /c0/dall set hidden=on(SCGCQ01571256)
- Instance Validation Failed between "system-schema.json" and "show all" JSON output.(SCGCQ01571961)
- Unified StorCLI 7.7 : Coverity issues - Resource leaks,Uninitialized variables,and dead code - Part 1(SCGCQ01600195)
- Drive Fw download Coverity fixes(SCGCQ01615074)
- Unified StorCLI 7.7 : StorCLI should not issue SL_SET_LIB_PARAMETERS command(SCGCQ01676983)
- Detailed status is not displayed on locating a drive which is not connected to IT card.(SCGCQ01571154)
- Coverity defect fixes for Memory Leak, Uninitialized pointers(SCGCQ01605182)
- storclio need to support proprietary i2c controller mode.(SCGCQ01732990)
- MR7.7 LSA 4.180.0 enclosure type is not matched with storcli(SCGCQ01747333)
- Coverity libmods issues - Resource leaks and Wrong sizes(SCGCQ01600208)
- Unified StorCLI 7.7 : MegaCLI commands report command status code in UEFI environment(SCGCQ01624506)
- storcli did not show current profile when connection in invalid config.(SCGCQ01713676)
- Unmap support mfc bit and fde type mixing fields needs to be updated when extracting factory settings and also while modifying factory settings(SCGCQ01640217)
- non-RAID:HII:CLI:Dedicated Hot Spare creation displays incorrect disk group association.(SCGCQ01698272)
- DHS:Unable to add dedicated Hot Spare drive to specified DG.(SCGCQ01714443)
- WWN for NVME PDs is reported as NA with MR(SCGCQ01731279)
- Updating the Diag results as per new API changes(SCGCQ01537255)
- Resource leaks,Uninitialized variables(SCGCQ01600311)
- Unified CLI : Coverity fixes for Uninitialized variables,resource leaks,and dead code handling - Part 3(SCGCQ01606785)
- Unified StorCLI 7.7 - Fixing coverity issues Resource leaks,Non-array deletes - Part 2(SCGCQ01757433)
- Storcli: UEFI shell error display-Error: Unsupported File open Mode.(SCGCQ01837752)
- Removal of ncurses references for linux makefile(SCGCQ01955544)
- Changing ini file name to storelibconfit.ini(SCGCQ01275669 port of SCGCQ01275496)
- Changing ini file name to storelibconfit.ini(SCGCQ01275670 port of SCGCQ01275496)
- Enumeration of drives in NGM[PERCCLI Implementation / HBA330 Mini Mezz](SCGCQ01529059 port of SCGCQ01458174)
- Storcli PR help execution delay is missing when PR running continuously(SCGCQ01537219 port of SCGCQ01534552)
- Handle memory leaks in getSortedPdList(SCGCQ01571890 port of SCGCQ01283497)
- Disk sorting based on connector name, slot and position(SCGCQ01571926 port of SCGCQ01307257)
- Collecting snapdump through StorCli(SCGCQ01594186 port of SCGCQ01581899)
- Unified StorCLI 7.6 : Creation of VD aborts StorCLI when FW returns error code for MR_DCMD_CFG_READ DCMD(SCGCQ01595361 port of SCGCQ01588245)
- Allow "noreset" option for IT controllers during firmware download(SCGCQ01599545 port of SCGCQ01514483)
- Enumeration of drives in NGM[PERCCLI Implementation / HBA330 Mini Mezz](SCGCQ01600137 port of SCGCQ01458174)
- StorCLI should not display SED property when using IT-HBA(SCGCQ01600142 port of SCGCQ01589445)
- Cutlass Phase 16 Storcli: Partner device ID should be suppressed under ./storcli /c0/eall show for multipath connections(SCGCQ01619201 port of SCGCQ01606780)
- Storcli should not create a snapdump image if there is no valid image(SCGCQ01624677 port of SCGCQ01623883)
- Removing readonly properties from for snapdump in storcli.(SCGCQ01669986 port of SCGCQ01669570)
- Different RetCode for N/A Drives - Parallel Drive Update(SCGCQ01682236 port of SCGCQ01681478)
- Storcli: VD creation fails from storcli in presence of 0KB bad drive .(SCGCQ01713567 port of SCGCQ01713240)
- Flashing PD's with parallel option wrong status is given by Storcli(SCGCQ01714667 port of SCGCQ01713734)
- Missing punctuation in Perccli delete config message(SCGCQ01714668 port of SCGCQ01698226)
- When a bad PD is flashed it fails as expected but error code is wrong(SCGCQ01714670 port of SCGCQ01713728)
- Parallel drive fw update on 1st drive fails, while drive fW update on another drive is in progress(SCGCQ01714671 port of SCGCQ01676426)
- Enclosure show status command gives success but nothing is shown(SCGCQ01731381 port of SCGCQ01731280)
- storclio need to support proprietary i2c controller mode.(SCGCQ01801679 port of SCGCQ01732990)
- Phase 7 - Drive Listing Is Not In Order for "/c0 show" & "/c0 show all"(SCGCQ01810054 port of SCGCQ01809355)
- EPD-PT behavior changes for Aero to support in RAID personality(SCGCQ01816139 port of SCGCQ01594176)
- perccli /cx delete config command getting incorrect error message.(SCGCQ01851908 port of SCGCQ01850719)
- State of the tape drive should be displayed as "JBOD" when FW state is MR_PD_STATE_SYSTEM(SCGCQ01853457 port of SCGCQ01853444)
- StorCLI hits segmentation fault on a Superdome Flex Server (with 16 MR cards in server(SCGCQ01911830 port of SCGCQ01886637)
- (Libmods) Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder)(SCGCQ01915314 port of SCGCQ01227144)
- Isolating faulty cable issue from bad drive issue for Aspen and Vail (Invader and Intruder(SCGCQ01915320 port of SCGCQ01222855)
- Updating ncurses library from 6.0 to 6.1(SCGCQ01915841 port of SCGCQ01836749)
- Disk performance throttled when running MegaCli AdpEvent log dump on Aspen and Vail (Invader and Intruder(SCGCQ01921533 port of SCGCQ01220901)
- Libmod changes: Adding CLI command to display/toggle new controller property.(SCGCQ01106982(SCGCQ01922038 port of SCGCQ01106988)
- LibMods : Adding the function that changing flag of full initialize completion(SCGCQ01922843 port of SCGCQ01141462)
- MFI Frame alignment(SCGCQ01922846 port of SCGCQ01064480)
- Square bracket is missing in the syntax of "set hardware device page" in storclio.(SCGCQ01929787 port of SCGCQ01224857)
- Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01526330 port of SCGCQ01274709)
- Change in RAID levels displaying in controller show all command(SCGCQ01540785 port of SCGCQ01509578)
- Ctrl-H hang during foreign import along with app tab toggling.(SCGCQ01571937 port of SCGCQ01356240)
- Data Abort Exception while entering CTRL R(SCGCQ01571939 port of SCGCQ01380831)
- Storcli_Aero: Storcli not able to detect controller at EFI shell without Avago MR driver.(SCGCQ01599436 port of SCGCQ01595698)
- This feature is not supported on this Controller" is displayed multiple times.(SCGCQ01599461 port of SCGCQ01595717)
- Unified StorCLI 7.6 : Creation of VD aborts StorCLI when FW returns error code for MR_DCMD_CFG_READ DCMD(SCGCQ01600150 port of SCGCQ01588245)
- Snapdump file user does not know the compression method(SCGCQ01624670 port of SCGCQ01616917)
- Storcli_Aero: unable to set sasadd methodport on IT controller.(SCGCQ01628097 port of SCGCQ01609234)
- Patrol read state shown as aborted while it actually is paused.(SCGCQ01714666 port of SCGCQ01714264)
- Storcli output does not list missing PD's(SCGCQ01715372 port of SCGCQ01715114)
- Grammatical mistakes in Perccli Un-supported RAID level warning message.(SCGCQ01720760 port of SCGCQ01714033)
- Unified StorCLI Phase 8 : NVMe and SAS Drive's WWN is incorrect for IT Controller(SCGCQ01749927 port of SCGCQ01749795)
- storcli /cx/pall show command fails with older generation cards that does not support PCIe pages(SCGCQ01758163 port of SCGCQ01520816)
- PERC10.2:CLI:Help: Grammatical Error in Text String "/ex - specifies a enclosure where X is the enclosure device ID."(SCGCQ01768428 port of SCGCQ01764888)
- "storcli show snapdump" output is incorrect(SCGCQ01817308 port of SCGCQ01817307)
- StorCLI should support firmware flash for SAS3 IR Controllers(SCGCQ01873578 port of SCGCQ01835627)
- show enclosure command is not exiting to shell(SCGCQ01874899 port of SCGCQ01814011)
- Storcli issuing 'add jbod drives=all' causes storcli to crash(SCGCQ01893370 port of SCGCQ01892288)
- Hide/Unhide command output display incorrect VD no for VDs on which the operation is not supported(SCGCQ01911848 port of SCGCQ01837932)
- Turn on the boodrive by storcli, HII does not reflect it, still shows "Off"(SCGCQ01915791 port of SCGCQ01816927)
- Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ01917007 port of SCGCQ01761309)
- PH9 PA StorCLI - /c0/eall/sal show all gives success message when no drives connected(SCGCQ01917168 port of SCGCQ01855721)
- Storcli: Ventura B0: BIOS Flashing Failure Observed in EFI Storcli and Multiple Tries Causes UART Unresponsive(SCGCQ01917338 port of SCGCQ01829667)
- Adding CLI command to display/toggle new controller property.(SCGCQ01922836 port of SCGCQ01106982)
- Storcli not working on large config setup when some of the drives are missing or the system has foreign config.(SCGCQ01940851 port of SCGCQ01940805)
- Expander FW download using storecli utility crashs.(SCGCQ01979615 port of SCGCQ01979599)
- Updating readme file(SCGCQ01294583 port of SCGCQ01294570)
- Remove sorting logic for array physical drives(SCGCQ01445612 port of SCGCQ01444666)
- Add /dev/sdX to StorCLI output(SCGCQ01514530 port of SCGCQ01505055)
- Allow "noreset" option for IT controllers during firmware download(SCGCQ01517643 port of SCGCQ01514483)
- Libmod: checking-in the changes forLibmods for SCGCQ01525764(SCGCQ01528935 port of SCGCQ01528886)
- Libmod: checking-in the changes forLibmods for SCGCQ01525764(SCGCQ01528936 port of SCGCQ01528886)
- Implemented to display the full Model number of the SATA drive when connected to an IT controller.(SCGCQ01528939 port of SCGCQ01525764)
- Unified StorCLI 7.6 : Read SBR fails with pre-ventura controllers(SCGCQ01539390 port of SCGCQ01539360)
- Removal of MegaCLI syntax from StorCLI(SCGCQ01591157 port of SCGCQ01504604)
- Unified LibMod changes for ER : SCGCQ01504604 - Removal of MegaCLI syntax from StorCLI(SCGCQ01591158 port of SCGCQ01504610)
- Spell error in /call/dall split mirror output.(SCGCQ01599464 port of SCGCQ01595709)
- storcli controller show all lists EPD's in VD list(SCGCQ01599486 port of SCGCQ01556595)
- Detailed status is not displayed on locating a drive which is not connected to IT card.(SCGCQ01599519 port of SCGCQ01571154)
- Storcli returns error for show file commands when parsing MR images eventhough the command was successful(SCGCQ01600149 port of SCGCQ01529009)
- Storcli_Aero: Storcli not able to detect controller at EFI shell without Avago MR driver.(SCGCQ01600151 port of SCGCQ01595698)
- Support only Dell SAS IT Controllers with PERCCLI(SCGCQ01618493 port of SCGCQ01547929)
- Cutlass Phase 16 Storcli: Partner device ID should be suppressed under ./storcli /c0/eall show for multipath connections(SCGCQ01625114 port of SCGCQ01606780)
- Cached IO policy(SCGCQ01627941 port of SCGCQ01607434)
- Space need in the output for secure erase(SCGCQ01714669 port of SCGCQ01713604)
- Unified StorCLI 7.7 : Unconfigured BAD drives are not displayed in /c0 show output(SCGCQ01718294 port of SCGCQ01718269)
- Unified StorCLI 7.7 : StorCLI doesn't report failure status when nopad image flashing fails via completeflash command in MR(SCGCQ01749921 port of SCGCQ01749849)
- storcli did not show current profile when connection in invalid config.(SCGCQ01760598 port of SCGCQ01713676)
- non-RAID:HII:CLI:Dedicated Hot Spare creation displays incorrect disk group association.(SCGCQ01760604 port of SCGCQ01698272)
- Storcli does not display the complete enclosure serial number(SCGCQ01760655 port of SCGCQ01735493)
- "storcli show snapdump" output is incorrect(SCGCQ01817270 port of SCGCQ01804779)
- Fails to set user defined value for delayOCR field in the SnampDump(SCGCQ01817941 port of SCGCQ01817465)
- Fails to set SnapDump savecount.(SCGCQ01817942 port of SCGCQ01817177)
- displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state"(SCGCQ01836905 port of SCGCQ01681538)
- Error message when Maximum number of VDs are reached(SCGCQ01911765 port of SCGCQ01856544)
- perccli /cx delete config command getting incorrect error message.(SCGCQ01911827 port of SCGCQ01850719)
- Unified LibMod changes : Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01913460 port of SCGCQ01893074)
- Add security-related compilation and linker flags to StorCLI - Linux(SCGCQ01913461 port of SCGCQ01892560)
- Add interface in storecli that could get relearn complete status(SCGCQ01914835 port of SCGCQ01848387)
- 6.13_SDS : Wrong error message is displayed on trying to create R0 vd on an pre configured drive as EPD.(SCGCQ01922844 port of SCGCQ01196785)
- Added new commands from StorCLI(SCGCQ01922845 port of SCGCQ01134166)
- Unified StorCLI : Enclosure devices are part of drive list used for drive operations(SCGCQ01979534 port of SCGCQ01979483)
- Add /dev/sdX to StorCLI output(SCGCQ01514531 port of SCGCQ01514516)
- Prepare To Transport(SCGCQ01568934 port of SCGCQ00936041)
- CacheCade VD association returns error in Config Utility (Ctrl-R(SCGCQ01571889 port of SCGCQ01264552)
- .(SCGCQ01571935 port of SCGCQ01325052)
- Commands "/call/all" return inappropriate message or segfault when both MR and IT controllers are connected(SCGCQ01599483 port of SCGCQ01561703)
- Un-supported command displayed for "storcli64.exe /call show sasaddress"(SCGCQ01620412 port of SCGCQ01619562)
- Update help contents for jbod delete(SCGCQ01625945 port of SCGCQ01624605)
- Storcli_Aero: unable to set sasadd methodport on IT controller.(SCGCQ01628094 port of SCGCQ01609234)
- Libmod Changes for Defect SCGCQ01595640 (CLI does not report Serial number for Lenovo D1224 Enclosure(SCGCQ01714307 port of SCGCQ01664412)
- Drive Listing Is Not In Order for "/c0 show" & "/c0/eall/sall show"(SCGCQ01732928 port of SCGCQ01714356)
- controller show wbsupport reason is not listed in the cli output(SCGCQ01760590 port of SCGCQ01561704)
- Storcli does not display the complete enclosure serial number(SCGCQ01760636 port of SCGCQ01735493)
- "Cached Virtual Drives" displayed in /c0/dall show cachecade without the table.(SCGCQ01760676 port of SCGCQ01537017)
- Trying to import Secured LDs and if wrong Security Key is mentioned, Error is referring to "Pass phrase"(SCGCQ01764539 port of SCGCQ01763866)
- Libmods: SCGCQ01760508 Error message-"Reached Maximum Supported virtual Disks" is displayed when no free space left create VD.(SCGCQ01764540 port of SCGCQ01764049)
- Enhance the detailed help for Firmware download and get bios command.(SCGCQ01792109 port of SCGCQ01790167)
- Updating ncurses library from 6.0 to 6.1(SCGCQ01837234 port of SCGCQ01836749)
- Add get VPD command support to StorCLI in OS environment(SCGCQ01911298 port of SCGCQ01852603)
- perccli(007.0523.0000.0000 Jul 20, 2018(SCGCQ01914827 port of SCGCQ01874120)
- Incorrect Interface Details for "storcli /c0 show" command(SCGCQ01915785 port of SCGCQ01837612)
- Invader/Intruder: MR 6.13.1- PD FW download status help to be updated(SCGCQ01922838 port of SCGCQ01256727)
- Change in RAID levels displaying in controller show all command(SCGCQ01511611 port of SCGCQ01509578)
- Implemented to display the full Model number of the SATA drive when connected to an IT controller.(SCGCQ01528940 port of SCGCQ01525764)
- Storcli PR help execution delay is missing when PR running continuously(SCGCQ01537216 port of SCGCQ01534552)
- Application crashes while executing storcli64.exe /c0/dall set hidden=on(SCGCQ01599467 port of SCGCQ01571256)
- Un-supported command displayed for "storcli64.exe /call show sasaddress"(SCGCQ01620417 port of SCGCQ01619562)
- syntax error while executing "storcli64.exe /c0 get firmware ? "(SCGCQ01620453 port of SCGCQ01618675)
- Storcli does not display the complete enclosure serial number(SCGCQ01760661 port of SCGCQ01735493)
- PH9 PA StorCLI - Tape drive entry not seen at "Requested boot drive" field after set bootdrive on(SCGCQ01853459 port of SCGCQ01850418)
- Unified StorCLI : StorCLI doesn't display OS Name for Windows Server 2019 server(SCGCQ01869194 port of SCGCQ01867354)
- StorCLI should not display SED property when using IT-HBA(SCGCQ01915857 port of SCGCQ01589445)
- Unified StorCLI Phase 9: Prints are seen in the console when SL_GET_CTRL_INFO fails from SL in uEFI platform(SCGCQ01917167 port of SCGCQ01866548)
- Unconfigured Good PD is showing as belonging to Disk Group 0.(SCGCQ01525771 port of SCGCQ01520567)
- Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01526326 port of SCGCQ01526321)
- This feature is not supported on this Controller" is displayed multiple times.(SCGCQ01599446 port of SCGCQ01595717)
- Incremented devicename is programmed for all the phy's in IT controller(SCGCQ01599449 port of SCGCQ01548481)
- controller show all command is not listing the Battery information(SCGCQ01599459 port of SCGCQ01561689)
- Support only Dell SAS IT Controllers with PERCCLI(SCGCQ01618501 port of SCGCQ01547929)
- syntax error while executing "storcli64.exe /c0 get firmware ? "(SCGCQ01620437 port of SCGCQ01618675)
- Invalid return status from Storcli(SCGCQ01731842 port of SCGCQ01731797)
- Unified StorCLI LibMods 7.6 - Moving CLI's VIB toolchain to 6.0 and workbench to 3.5.7(SCGCQ01749416 port of SCGCQ01720952)
- DHS:Unable to add dedicated Hot Spare drive to specified DG.(SCGCQ01760603 port of SCGCQ01714443)
- Add Downgrade Firmware function in Storcli(SCGCQ01813396 port of SCGCQ01583223)
- Libmod changes for StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers - SCGCQ01775602(SCGCQ01853371 port of SCGCQ01775616)
- Unified StorCLI : StorCLI doesn't display OS Name for Windows Server 2019 server(SCGCQ01916018 port of SCGCQ01867354)
- Unconfigured Good PD is showing as belonging to Disk Group 0.(SCGCQ01525774 port of SCGCQ01520567)
- Spell error in /call/dall split mirror output.(SCGCQ01599466 port of SCGCQ01595709)
- Get VPD from MPB region is failure, but overalll status shows success(SCGCQ01599481 port of SCGCQ01589618)
- Compilation errors while compiling parser module(SCGCQ01600565 port of SCGCQ01600563)
- CLI does not report Serial number for Enclosure.(SCGCQ01714296 port of SCGCQ01595640)
- Unified StorCLI 7.6 - Moving CLI's VIB toolchain to 6.0 and workbench to 3.5.7(SCGCQ01745530 port of SCGCQ01720947)
- Updating the Diag results as per new API changes(SCGCQ01537265 port of SCGCQ01537255)
- Collecting snapdump through StorCli (Libmods(SCGCQ01594187 port of SCGCQ01589854)
- WWN for NVME PDs is reported as NA with MR(SCGCQ01749397 port of SCGCQ01731279)
- Unified StorCLI 7.7 : StorCLI should not issue SL_SET_LIB_PARAMETERS command(SCGCQ01758162 port of SCGCQ01676983)
- Spell mistake in error message for hwdev command(SCGCQ01760594 port of SCGCQ01614972)
- Error message-"Reached Maximum Supported virtual Disks" is displayed when no free space left create VD.(SCGCQ01764538 port of SCGCQ01760508)
- PERCCLI_PERC10.2-007.0512/When selecting a PD that is not configurable, it is showing "Atleast" which should be "At least"(SCGCQ01768422 port of SCGCQ01764929)
- StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers(SCGCQ01853405 port of SCGCQ01775602)
- Unified StorCLI : Drive after the enclosure is not displayed as part of /eall/sall show [all] command(SCGCQ01977760 port of SCGCQ01948579)
EnhancementRequests
- Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01473897)
- Adding JSON schema for Virtual Drive level commands(SCGCQ01516772)
- Enhance StorCLI show file= to include PnP ID(SCGCQ01517431)
- Need Storcli support drive FW upgrade(SCGCQ01583217)
- displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state"(SCGCQ01681538)
- Add ForceHCB option in StorCLI for IT controllers(SCGCQ01718946)
- Switch attached NVMe HW RAID support for Supermicro backplanes(SCGCQ01720819)
- Added customer serial number field to MFC Manufacturing 2 structure(SCGCQ01873417)
- MR API changes to support EKMS over OOB(SCGCQ01874035)
- Add new error code for tampered or invalid controller(SCGCQ01885686)
- Interrupt coalsecing setting per group of 8 replies queues (h/w VF registers(SCGCQ01886424)
- [MR 7.8] API change to export "disable least latency mode"(SCGCQ01887495)
- HDET: Support smp passthrough storeliboob (API changes requirement(SCGCQ01916035)
- Add secure boot key update complete event(SCGCQ01928254)
- Add Board Support Package Image Type to MR_IMAGE_TYPE(SCGCQ01931637)
- Support dynamically add/remove controller in Storelib IT for MCTP over PCIe(SCGCQ01934815)
- Fix MR_CTRL_INFO to support backward compatibility(SCGCQ01946548)
- Add a new log event used whenever the snap dump properties are modified.(SCGCQ01963328)
- Add a bit for atomic descriptor capable(SCGCQ01965047)
- Add Downgrade Firmware function in Storcli(SCGCQ01583223)
- Add support for TCG Opal 2.0 compliant SAS/SATA HDDs, SAS/SATA HDDs operations in StorCLI(SCGCQ01593849)
- StorCLI JSON 4.0 compliant schema creation for Phy (including mux and lane) level commands(SCGCQ01594119)
- Improve PERCcli Terminology When in eHBA Mode(SCGCQ01615487)
- UNMAP/TRIM/WRITESAME for NVMe devices for R0/1/EPD/JBOD(SCGCQ01727113)
- Adding JSON schema for Drive Group and Foreign configuration commands(SCGCQ01531269)
- Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01583226)
- Libmods : Improving SAS bus test coverage by checking PHY error count when linking at 12G speed using a SAS loopback.(SCGCQ01615540)
- To add restriction on personality change requests from RAID to eHBA and eHBA to RAID(SCGCQ01721528)
- StorCLI JSON 4.0 compliant schema creation for Enclosure, BBU and CacheVault commands(SCGCQ01576130)
- Add get VPD command support to StorCLI in OS environment(SCGCQ01852603)
- Improve PERCcli Terminology When in eHBA Mode(SCGCQ01628424)
- Porting StorCLI Huawei Criteo requirement from 7.4 to 7.5(SCGCQ01761309)
007.0525.0000.0000 - Moderate Impact/Low Probability of Occurrence
--------------------
Defects (16)
-.(SCGCQ01753405)
- Grammatical mistakes in Perccli Un-supported RAID level warning message.(SCGCQ01714033)
- Correcting the grammatical errors in firmware's MFI Stat messages.(SCGCQ01717315)
- Enclosure show status command gives success but nothing is shown.(SCGCQ01731280)
- One of the requirement for Criteo is to display JBOD-WB (EPD) to OS drive mapping.(SCGCQ01804763)
- Turn on the boodrive by storcli, HII does not reflect it, still shows "Off".(SCGCQ01816927)
- Incorrect Interface Details for "storcli /c0 show" command.(SCGCQ01837612)
- Two MCTP error codes in slerrors.h show same offset code 0x7098.(SCGCQ01627548)
- Space need in the output for secure erase.(SCGCQ01713604)
- seg fault is seen when when we try to generate CRC errors using megamon.(SCGCQ01841619)
- Missing punctuation in Perccli delete config message.(SCGCQ01698226)
- Personality Behavior Modes:Command returns failure when setting non-RAID behavior modes.(SCGCQ01713265)
- non-RAID:HII:CLI:Dedicated Hot Spare creation displays incorrect disk group association.(SCGCQ01698272)
- DHS:Unable to add dedicated Hot Spare drive to specified DG.(SCGCQ01714443)
- WWN for NVME PDs is reported as NA with MR.(SCGCQ01731279)
- Storcli: UEFI shell error display-Error: Unsupported File open Mode.(SCGCQ01837752)
- perccli /cx delete config command getting incorrect error message.(SCGCQ01851908 port of SCGCQ01850719)
- storclio need to support proprietary i2c controller mode.(SCGCQ01801679 port of SCGCQ01732990)
- State of the tape drive should be displayed as "JBOD" when FW state is MR_PD_STATE_SYSTEM.(SCGCQ01853457 port of SCGCQ01853444)
- Phase 7 - Drive Listing Is Not In Order for "/c0 show" & "/c0 show all".(SCGCQ01810054 port of SCGCQ01809355)
- storcli /cx/pall show command fails with older generation cards that does not support PCIe pages.(SCGCQ01758163 port of SCGCQ01520816)
- Unified StorCLI Phase 8 : NVMe and SAS Drive's WWN is incorrect for IT Controller.(SCGCQ01749927 port of SCGCQ01749795)
- storcli did not show current profile when connection in invalid config.(SCGCQ01760598 port of SCGCQ01713676)
- Storcli does not display the complete enclosure serial number.(SCGCQ01760655 port of SCGCQ01735493)
- Unified StorCLI 7.7 : StorCLI doesn't report failure status when nopad image flashing fails via completeflash command in MR.(SCGCQ01749921 port of SCGCQ01749849)
- Unified StorCLI 7.7 : Unconfigured BAD drives are not displayed in /c0 show output.(SCGCQ01718294 port of SCGCQ01718269)
- "Cached Virtual Drives" displayed in /c0/dall show cachecade without the table.(SCGCQ01760676 port of SCGCQ01537017)
- controller show wbsupport reason is not listed in the cli output.(SCGCQ01760590 port of SCGCQ01561704)
- Updating ncurses library from 6.0 to 6.1.(SCGCQ01837234 port of SCGCQ01836749)
- Drive Listing Is Not In Order for "/c0 show" & "/c0/eall/sall show".(SCGCQ01732928 port of SCGCQ01714356)
- Storcli does not display the complete enclosure serial number.(SCGCQ01760661 port of SCGCQ01735493)
- Unified StorCLI : StorCLI doesn't display OS Name for Windows Server 2019 server.(SCGCQ01869194 port of SCGCQ01867354)
- PH9 PA StorCLI - Tape drive entry not seen at "Requested boot drive" field after set bootdrive on.(SCGCQ01853459 port of SCGCQ01850418)
- Libmod changes for StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers - SCGCQ01775602.(SCGCQ01853371 port of SCGCQ01775616)
- Add Downgrade Firmware function in Storcli.(SCGCQ01813396 port of SCGCQ01583223)
- Spell mistake in error message for hwdev command.(SCGCQ01760594 port of SCGCQ01614972)
- StorCLI doesn't call SL_EXIT_LIB in VMware environment for MR Controllers.(SCGCQ01853405 port of SCGCQ01775602)
- Unified StorCLI 7.7 : StorCLI should not issue SL_SET_LIB_PARAMETERS command.(SCGCQ01758162 port of SCGCQ01676983)
EnhancementRequests (30)
- API Changes for Driver/FW DCMD HandShake.(SCGCQ01841266)
- RTTrace Enable/Disable API changes.(SCGCQ01830211)
- Criteo: API changes reversal.(SCGCQ01760512)
- RTTrace API Changes.(SCGCQ01745568)
- API changes needed to support eHBA product series.(SCGCQ01727346)
- Create sanitize events.(SCGCQ01713708)
- MPI 2.5: Add MaxEnclosureLevel field to BIOS Page 1.(SCGCQ01570730)
-.(SCGCQ01593479)
-.(SCGCQ01761309)
- displaying ONFI flash state command: storcli /cx/cv show all New Feild: "NVCache state".(SCGCQ01681538)
- API change for Switch attached NVMe HW RAID support for Supermicro backplanes.(SCGCQ01697667)
- Mixing Rules for SED and non-SED drives to create non-secure array with controller security enabled.(SCGCQ01757538)
- Unmap: Define new API for enhanced UNMAP support.(SCGCQ01758062)
- Adding API bit to indicate whether forced personality change is supported or not.(SCGCQ01762153)
- Unmap: Define new events for enhanced UNMAP support [MR7.8].(SCGCQ01803319)
- Deprecate the snap dump fields that are no longer needed for MR_SNAP_DUMP_PROPERTIES structure.(SCGCQ01816724)
-.(SCGCQ01818580)
- Add the API to clear all the snap-dumps from firmware.(SCGCQ01824135)
- API change to provide learn complete timestamp.(SCGCQ01845269)
- Added Support for Triggering SnapDump.(SCGCQ01848759)
- Add secure boot support.(SCGCQ01792416)
- Improve PERCcli Terminology When in eHBA Mode.(SCGCQ01615487)
- Including The Time Stamp for every Snap Dump created in the firmware.(SCGCQ01797424)
- Aero FW - Reporting SSD wear gauge values for OEM specific customers.(SCGCQ01798686)
- [MR 7.8] API change to return apt failure status for a personality change request.(SCGCQ01853480)
- Added new events for unmap policy changes.(SCGCQ01871912)
- MPI 2.5: Add OEMRD field to SAS Enclosure Page 0.(SCGCQ01553021)
- API Changes - After Vision PSOC FW update, applications should ask the user for power cycle instead of reboot.(SCGCQ01765150)
- To add restriction on personality change requests from RAID to eHBA and eHBA to RAID.(SCGCQ01721528)
- Add get VPD command support to StorCLI in OS environment.(SCGCQ01852603)
0007.0507.0000.0000-1 - Moderate Impact/Low Probability of Occurrence
-------------------
Defects (75)
- Profile Mgmt API Changes.( SCGCQ00883008)
- MR_RAID_CTX_G35 has one too many bits.(SCGCQ00886417)
- Reintroduce numSGEExt Field in Raid Context for Invader to support 1MB IO.(SCGCQ00927738)
- The code had events with repetitive ID and some structures clashing.(SCGCQ00948535)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23.(SCGCQ01001936)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23 has been added back again into adapteroperations 4.(SCGCQ01014835)
- 800C error when execting Get MFC default function.(SCGCQ01037840)
- Enable WB support via API.(SCGCQ01405242)
- Storcli: Instance Validation Failed between "controller-properties-schema.json" and "show" json..(SCGCQ01413239)
- Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON..(SCGCQ01423458)
- Port linkspeed is displayed in a different JSON object for NVMe drives.(SCGCQ01436920)
- Remove unsupported Ethernet code for IT controller from CLI.(SCGCQ01448979)
- Show command is not processed for IT firmware and IT complete flash images in big endian server.(SCGCQ01451940)
- storcli /c0/e123/s1 show poh shows drive info on IT controller.(SCGCQ01456171)
- Storcli displays "success" and "failure" both when trying to enable UNMAP on RAID5 using SSDs..(SCGCQ01462396)
- Storcli verbose help for Unmap has spelling mistakes.(SCGCQ01462401)
- Updating the JSON Schema for the SCSI Unmap feature.(SCGCQ01465745)
- Storcli: Instance Validation Failed between "system-schema.json" and "show" JSON..(SCGCQ01467131)
- Part 1 : Fixing coverity issues - Resource leaks and Illegal comparison.(SCGCQ01470420)
- Instance Validation Failed between "virtual-drive-config-schema.json" and "add vd " JSON.(SCGCQ01471852)
- Start/Stop locate on a invalid enclosure returns success.(SCGCQ01480910)
- Detailed help contents were not present for most of the IT download options..(SCGCQ01483760)
- Spelling errors in the "/cx restart" command..(SCGCQ01486415)
- Storcli: Instance Validation Failed between "controller-flash-component-erase-schema.json" and "flasherase" JSON..(SCGCQ01506022)
- Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show_profile" JSON..(SCGCQ01506052)
- CLI help does not reflect the new command to create an ePD.(SCGCQ01639583)
- Phase3 Beta PCIe: Loading SLOOB fails with error message "ExitLib failed for SAS IT Controller!! rval 0x801A".(SCGCQ01292964)
- Instance Validation is failing for mentioned commands..(SCGCQ01415355)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show all" JSON output..(SCGCQ01423447)
- Incorrect PNP ID format is displayed in EFI for firmware and complete flash images.(SCGCQ01448990)
- PH6 Ventura Pre-Alpha - StorCLI - "show file = fw.bin" command usage is not updated in help.(SCGCQ01460588)
- Showing empty error msg in CLI when Unmap not supported is returned by FW..(SCGCQ01464580)
- Storcli: Instance Validation Failed between "enclosure-schema.json" and "/call/eall show" JSON..(SCGCQ01467146)
- Storcli: Instance Validation Failed between "jbod-show-schema.json" and "/call/jbodall show" JSON..(SCGCQ01467694)
- PH6 Ventura Pre-Alpha - StorCLI - /c0 show all - Capabilities for supported drives seen only SAS/SATA, NVMe not found.(SCGCQ01480920)
- PH6 Ventura - Storcli crashed in Win2016 when "storcli64.exe J" is executed.(SCGCQ01488062)
- Instance Validation Failed between "controller-termlog-schema.json" and "set termlog=off" JSON..(SCGCQ01506041)
- Readme file have no mention of PD and JBOD level command support..(SCGCQ01507421)
- Checking in VBAS compliation changes.(SCGCQ01630324)
- PERCCLI ePD personality behavior command is still an available option and has not been removed.(SCGCQ01639798)
- Storcli: VD creation fails from storcli in presence of 0KB bad drive.(SCGCQ01713240)
- Operating system is not displaying the version in EFI for any of command in cli.(SCGCQ01410613)
- Instance Validation Failed between "controller-ASO-schema.json" and "show ASO" json.(SCGCQ01430237)
- Updating pre-ventura SBR fails with "hwdevice" command.(SCGCQ01438214)
- MR7.5: StorCLI reports Multipath ON during set but OFF during show commands.(SCGCQ01440234)
- Adding excludevd option to the help file of patrolread command.(SCGCQ01443435)
- PH6 Ventura Pre-Alpha - StorCLI - /cx/ set bootdrive = on/off command not updated in help page.(SCGCQ01460582)
- Schema addition for "show file=" command.(SCGCQ01461209)
- PH6 Ventura Pre-Alpha -- "storcli64.exe /c0 compare ssid ver = 2 J" command crashes and utility stopped working in Win2016.(SCGCQ01462593)
- MR 7.5_UNMAP : UNMAP support info is not shown in controller supported operations and VD properties.(SCGCQ01464562)
- PH6 Ventura StorCLI - Pre-Alpha - /cx compare detailed help is not giving complete information.(SCGCQ01464762)
- Instance Validation Failed between "controller-patrolread-set-schema.json" and "/c0 set pr excludevd=1" JSON.(SCGCQ01472845)
- Instance Validation Failed between "drive-operations-patrolread-schema.json" and "/call/e65/sall show patrolread".(SCGCQ01473344)
- Grammatical error in Perccli warning message during FW Flash.(SCGCQ01686670)
- OpROM's and their versions are not displayed for 8,32,and 64 MB IT complete flash images.(SCGCQ01449785)
- Part 3 : Fixing coverity issue : Resource leaks.(SCGCQ01472797)
- Storcli: Instance Validation Failed between schema and JSON output for many scenarios with one common error.(SCGCQ01506038)
- Reverting back SL_MAX_OS_DRIVE_COUNT value to 300.(SCGCQ01114306)
- Assign VDs suboption in cachecade VD creation is not assigning the intended VDs.(SCGCQ01419754)
- Incorrect help description for erase and download completeflash commands.(SCGCQ01470263)
- Instance Validation Failed between "controller-jbod-schema.json" and "add jbod" JSON..(SCGCQ01472802)
- Storcli: Instance Validation Failed for direct attached drive commands..(SCGCQ01472833)
- Check for supported pages for firing drive SCSI commands.(SCGCQ01474325)
- No error description when start/stop locate fails on the drive from StoreLIBIT library.(SCGCQ01480900)
- IT command to set sasadd and other set operations shows success for an MR controller.(SCGCQ01483753)
- Changing CV/BBU state algorithm according to the updated design document..(SCGCQ01388595)
- DriveID and errormsg are coming improper on drive POH command when failed.(SCGCQ01443683)
- Storcli: Instance Validation Failed between "controller-linkconfig-schema.json" and "show linkconfig" json..(SCGCQ01465446)
- Coverity libmods issues - Resource leaks and Wrong sizes.(SCGCQ01472195)
- Storcli: Instance Validation Failed between "enclosure-drive-detailed-schema.json" and "/call/eall/sall show all" json..(SCGCQ01473334)
- Unified StorCLI does not support erasing of persistent config pages in host for IT controllers.(SCGCQ01466766)
- Storcli: Instance Validation Failed between "jbod-show-schema.json" and "/c0/jbodx show" JSON..(SCGCQ01472821)
- UEFI StorCLI should detect controller when UEFI driver is not present and when FW is in ready state.(SCGCQ01489472)
- The structure name is changed from oob_i2c to oob to avoid compilation failure in OOB SL.(SCGCQ01015024)
- Instance Validation Failed between "controller-freespace-schema.json" and "show freespace" JSON output..(SCGCQ01414749)
EnhancementRequests (174)
- MPI2: Add TargetModeAbort by initiator device handle.(SCGCQ00337167)
- New fault code for routine synchronous reset.(SCGCQ01264142)
- MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually.(SCGCQ00574358)
- MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag).(SCGCQ00414050)
- MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply.(SCGCQ00396414)
- MPI2: Add OEM Identifier to BIOS Page 1.(SCGCQ00357228)
- MPI2: Use Slot Information during Port Enable Event Replay option.(SCGCQ00356796)
- MPI2: Add new TargetModeAbort AbortType to only abort Command IUs.(SCGCQ00345215)
- MPI v2.6: Additional request and reply descriptor formats.(SCGCQ00259613)
- Modify event string APIs for MISSING and OFFLINE LDs.(SCGCQ01628177)
- New configuration params added for EPD-PT devices.(SCGCQ01599607)
- MR API change request to Enable/disable the parallel PD FW update feature based on PNP ID’s.(SCGCQ01595347)
- Implement Snapdump debugging capability.(SCGCQ01567770)
- Add "Incompatible with Profile" event.(SCGCQ01289924)
- API changes for CR55 - PCIe lane/link speed.(SCGCQ01222700)
- API change for Simplified RAID10 Creation.(SCGCQ01222698)
- API Changes Required for Specific OEM Backplane functionality.(SCGCQ01218406)
- API changes for PR SCGCQ01139678 - Method for determining bad ONFI flash in storcli.(SCGCQ01215334)
- MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0.(SCGCQ01213028)
- MPI 2.5: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01208954)
- API changes for PR SCGCQ01127742 - Isolating faulty cable issue from bad drive issue.(SCGCQ01203751)
- MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP.(SCGCQ01180886)
- MR 6.12 - Add JBOD mode personality to MR_CTRL_PERSONALITY.(SCGCQ01146597)
- MR 7.0: Add supportPdMapTargetId flag in MR_CTRL_INFO and MFI_CAPABILITIES.(SCGCQ01141251)
- MR 6.13: Add API support for TFM/SCAP _MR_BBU_VPD_INFO_FIXED parameters.(SCGCQ01139344)
- MR 6.13: Add a new control command to fetch ROC temperature data over I2C.(SCGCQ01137627)
- MR 7.2: Add API support to make application work with Cachecade3.0 on Ventura (Public).(SCGCQ01114969)
- MPI 2.5: Add new connector types.(SCGCQ01085073)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ01002367)
- MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout".(SCGCQ00996127)
- MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1.(SCGCQ00853162)
- MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable.(SCGCQ00791885)
- MPI 2.5: add WWID to BIOS Page 3.(SCGCQ00785208)
- MPI 2.5: update copyright info.(SCGCQ00728066)
- MPI 2.5: BIOS Page 1 additions.(SCGCQ00700829)
- MPI 2.5: distribute Target Command Buffers Received across multiple reply queues.(SCGCQ00685820)
- MPI 2.0: Add product-specific Flag bit to Clean Tool.(SCGCQ00569175)
- Add type BIOS for HashImageType..(SCGCQ00566306)
- Identify physical location of a target device.(SCGCQ00523879)
- MPI 2.5: add reserved fields to IO Unit Page 7 for future use.(SCGCQ00477817)
- MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps".(SCGCQ00471293)
- MPI 2.5: Signed images for FWDownload.(SCGCQ00469990)
- MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL.(SCGCQ00438437)
- MPI 2.5: Toolbox Console Text Display Tool.(SCGCQ00415512)
- Allow Protection Information bit for IR Volume Create.(SCGCQ00385306)
- MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply.(SCGCQ00357551)
- MPI 2.6: add PCIe Device Config Pages.(SCGCQ00345271)
- MPI 2.6: PCIe Switch Config Pages.(SCGCQ00345270)
- MPI 2.6: PCIe Topology Change List Event.(SCGCQ00345266)
- MPI 2.6: add PCIe Event Data (Generic), PCIe Device Status Change Event, and PCIe Enumeration Event.(SCGCQ00345260)
- MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors.(SCGCQ00338506)
- MPI 2.6: PCIe IO Unit Page 0 & 1 definitions.(SCGCQ00336383)
- MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1.(SCGCQ00310439)
- MPI 2.6: update SGL chapter to include PCIe.(SCGCQ00294131)
- MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request.(SCGCQ00294055)
- MPI 2.6: NVMe Encapsulated request.(SCGCQ00264759)
- MPI 2.6: SOP Encapsulated request.(SCGCQ00264755)
- Improve PERCcli Terminology When in eHBA Mode.(SCGCQ01615487)
- JSON schema for Drive level commands.(SCGCQ01445435)
- MPI 2.6 Add Atomic Request Descriptor capability.(SCGCQ00227735)
- MPI 2.6: add IO Unit Control Request.(SCGCQ00345258)
- MPI 2.6: PCIe Link Config Pages.(SCGCQ00345272)
- MPI 2.6: Enclosure Management.(SCGCQ00345273)
- Device Info field for PCIe devices.(SCGCQ00353339)
- MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request.(SCGCQ00360843)
- MPI 2.6: new family values for ProductID fields.(SCGCQ00360952)
- MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11.(SCGCQ00363600)
- Modified address space bits.(SCGCQ00397136)
- MPI 2.6: Add PCIe IO Unit Page 4.(SCGCQ00397563)
- MPI 2.6: Add board power fields to IO Unit Page 7.(SCGCQ00397572)
- MPI 2.6: Add support for SAS Persistent Connections.(SCGCQ00397577)
- MPI 2.6: Add NVMe SGL support.(SCGCQ00398256)
- MPI 2.6: Add NVMe SGL support to IEEE SGL.(SCGCQ00432541)
- MPI 2.6: System Interface Register Set update.(SCGCQ00464402)
- Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request.(SCGCQ00480292)
- MPI 2.6: shutdown operation for IO Unit Control Request.(SCGCQ00496998)
- MPI 2.6: Add supported link rates and widths for PCIe devices.(SCGCQ00564281)
- MPI 2.6: Add additional NVMe AccessStatus codes.(SCGCQ00574070)
- MPI 2.6: Add BootFlags field to Firmware Image Header.(SCGCQ00601869)
- MPI 2.6: Add new FLASH region types.(SCGCQ00619371)
- MPI 2.6: Added an additional signature value for the firmware image header.(SCGCQ00623271)
- MPI 2.6: additional AccessStatus values for PCIe Device Page 0.(SCGCQ00664957)
- MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages.(SCGCQ00680527)
- MPI 2.6: Extend Task Management - Target Reset Method to include PCIe devices.(SCGCQ00686666)
- MPI 2.6: Add device off flag to SCSI Enclosure Processor messages.(SCGCQ00776177)
- MPI 2.6: New Phy event codes added to Ventura.(SCGCQ00789600)
- MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough.(SCGCQ00813389)
- MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura.(SCGCQ00827088)
- MPI 2.6: add PCI Device ID's.(SCGCQ00828497)
- MPI 2.6: methods to report Active Cable power problems.(SCGCQ00831588)
- MPI 2.6: SRIOV support for PCIe devices.(SCGCQ00852827)
- MPI 2.6: Update Flash Signature..(SCGCQ00852831)
- profile management API.(SCGCQ00867953)
- MPI 2.6: add new feature to control NVMe SGL format.(SCGCQ00872169)
- Mega API modifications needed for RMW-FP and Cache bypass features in Ventura.(SCGCQ00875328)
-.(SCGCQ00878757)
- Merging api_overrides mega_api files with the files in the Mega_API development stream.(SCGCQ00883262)
- MPI 2.6: Update Ventura family device ids to match latest EDS.(SCGCQ00915256)
- MPI 2.6: update Marlin-class device IDs.(SCGCQ00915336)
- MPI 2.6: Remove all SOP references.(SCGCQ00925839)
- Ventura: de-feature AHCI.(SCGCQ00941620)
- MPI 2.6: Remove all AHCI references.(SCGCQ00948258)
- MPI 2.6: Add support for SAS-4 and PCIe-4.(SCGCQ00948955)
- MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0.(SCGCQ00949638)
- MPI 2.6: add LinkNum field to the PCIe Link configuration pages.(SCGCQ00954619)
-.(SCGCQ00987840)
- MPI-2.6: backend PCIe feature initialization status reporting.(SCGCQ01009104)
- MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request.(SCGCQ01013930)
- MPI2.6: Fix defines that are not unique within the first 32 characters.(SCGCQ01015826)
- MPI 2.6: direct reporting of negotiated PCIe link width and speed.(SCGCQ01017027)
- MPI 2.6: Backend SRIS mode enable flag.(SCGCQ01018687)
- MPI2.6: Reserve ExtPageTypes for Dragon.(SCGCQ01020473)
- MR_CTRL_INFO expansion from 2K to 4K.(SCGCQ01023741)
- mega api changes for ibuttonless PR.(SCGCQ01059740)
- MPI2.6: Add x16 PCI support for Marlin family products.(SCGCQ01063009)
- MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page.(SCGCQ01071374)
- Profile Management Changes to support requestedProfileID and optimisedProfile.(SCGCQ01075821)
-.(SCGCQ01082303)
-.(SCGCQ01085954)
- MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout".(SCGCQ01092340)
- MEGA_API Changes to incorporate new IO subtype to support redirect cached IO.(SCGCQ01094549)
- MPI 2.6: Add Sea Arch class and Product IDs.(SCGCQ01116837)
- MR 7.0: Add MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT = 7 to mfi.h file.(SCGCQ01133839)
- MPI2.6: Added new image type and flash region definitions.(SCGCQ01136127)
- MPI 2.6: Add new clean tool options.(SCGCQ01141732)
- MPI 2.6: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01146583)
- Define CurrentFwNvmePageSize element in new MFI_REG_STATE_EXT3 register.(SCGCQ01188725)
- MR7.1. Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01213092)
- MPI2.6: Mfg7 support for arbitrary starting slot number.(SCGCQ01213267)
- Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01216848)
- MPI 2.6: Add new firmware download type (CBB BACKUP).(SCGCQ01258005)
- MPI 2.6: Add new firmware download type (CPLD IMAGE).(SCGCQ01305760)
- MPI 2.6: add NVMe SGL Data Block descriptor alignment flag.(SCGCQ01339864)
- MPI 2.6: Add Aero PCI Device IDs.(SCGCQ01373008)
-.(SCGCQ01389581)
- MPI 2.6: Add ControllerResetTO to PCIe Device Page 2.(SCGCQ01416498)
- MPI 2.6: Add new reason code to PCIE Device Status Change Event.(SCGCQ01416515)
- Add Test Link Diagnostic API.(SCGCQ01436268)
- Add a new structure to provide OEMs ability to switch to select either I2C or PCIe as an out of band transport.(SCGCQ01445048)
- MPI 2.6: PCIe Device Page 2 reporting Namespace Optimal IO Boundary(NOIOB) for NVMe devices.(SCGCQ01449138)
- Provide OEMs ability to select either I2C or PCIe as an out of band transport.(SCGCQ01450245)
- Update description of MR_DCMD_CTRL_PERSONALITY_SET Dcmd.(SCGCQ01467149)
- Added MR_MFC_DEFAULTS.NVMeAbortTO and MR_MFC_DEFAULTS.NVMeMaxControllerResetTO.(SCGCQ01532045)
- Add support for API fields to report SED type of PD.(SCGCQ01587230)
- Add OnOff parameter in Properties2 of Structure MR_CTRL_PROP to enable/disable mix of Enterprise & Opal SED drives.(SCGCQ01593520)
- NVDATA parameter to OPAL SED.(SCGCQ01614689)
- Added a new interface between driver-aops to indicate if 64 bit SGL support is enabled.(SCGCQ01620350)
- Add new MFI Status to block requested operation due to existing controller configuration.(SCGCQ01670135)
- Change the mr.h API comment showing the new return status for the - MR_DCMD_PD_GET_INFO.(SCGCQ01670234)
- Add support to defeature Cached I/O policy.(SCGCQ01581032)
- New events for PR/CC conflicts and sector size mismatch.(SCGCQ01227051)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ00988360)
- MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses.(SCGCQ00466819)
- Removing the NMR storcli commands from storcli..(SCGCQ01445268)
- Add support to allow Device names greater than 107.(SCGCQ01039328)
- MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs.(SCGCQ00397568)
- MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit.(SCGCQ00884740)
- MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks.(SCGCQ00922213)
- MPI 2.6: Device side PCIe SRNS flag.(SCGCQ01276256)
- Checking of VBAS make file DataPro of Univ_viva_libmods.(SCGCQ01488176)
- Profile Management: Storcli - Add support for WB bit in profile management show.(SCGCQ01445628)
- Removing the NMR storcli commands from storcli..(SCGCQ01445418)
-.(SCGCQ01428114)
-.(SCGCQ01423509)
- Provide end-user ability to select either I2C or PCIe as an out of band transport.(SCGCQ01452987)
- Add NVMe device related changes.(SCGCQ01034678)
- Provide end-user ability to select either I2C or PCIe as an out of band transport.(SCGCQ01452986)
- Add boot drive selection support in Stor-CLI.(SCGCQ01445896)
- Improve PERCcli Terminology When in eHBA Mode.(SCGCQ01628424)
-.(SCGCQ01466805)
- StorCLI Libmods - Ventura LD de-allocation support on SAS/SATA SSDs through UNMAP/WRITE SAME on non-PARITY, non-DIF.(SCGCQ01448954)
- StorCLI - Ventura LD de-allocation support on SAS/SATA SSDs through UNMAP/WRITE SAME on non-PARITY, non-DIF volumes.(SCGCQ01447799)
- Adding JSON schema for JBOD and Drive level commands.(SCGCQ01445308)
- Add support for IT Firmware images and IT Completeflash images to "show file=" command.(SCGCQ01436882)
CSETActivities (57)
- StorCLI should not display SED property when using IT-HBA.(SCGCQ01600142 port of SCGCQ01589445)
- Enumeration of drives in NGM[PERCCLI Implementation / HBA330 Mini Mezz](SCGCQ01600137 port of SCGCQ01458174)
- Allow "noreset" option for IT controllers during firmware download.(SCGCQ01599545 port of SCGCQ01514483)
- Storcli show displays OS Version appended with Technical Preview.(SCGCQ01478448 port of SCGCQ01474457)
- Storcli: Instance Validation Failed between "controller-cc-schema.json" and "show consistencycheck" JSON(SCGCQ01456168 port of SCGCQ01451170)
- Phase 5 : Command "storcli /c0 show all" crashes with drives connected to SAS3.5 IT controller(SCGCQ01452992 port of SCGCQ01452982)
- Instance Validation Failed between "controller-ASO-schema.json" and "show ASO" json(SCGCQ01430285 port of SCGCQ01430237)
- SLT : Requesting user to enter the allocated response length of SMP request page(SCGCQ01202087 port of SCGCQ01202030)
- Changing ini file name to storelibconfit.ini(SCGCQ01275669 port of SCGCQ01275496)
- Unified StorCLI 7.6 : Creation of VD aborts StorCLI when FW returns error code for MR_DCMD_CFG_READ DCMD(SCGCQ01600150 port of SCGCQ01588245)
- This feature is not supported on this Controller" is displayed multiple times(SCGCQ01599461 port of SCGCQ01595717)
- Storcli may not be able to show the RAID controller in some special situation(SCGCQ01500340 port of SCGCQ01392154)
- Port linkspeed is displayed in a different JSON object for NVMe drives(SCGCQ01438288 port of SCGCQ01436920)
- Changing ini file name to storelibconfit.ini(SCGCQ01275670 port of SCGCQ01275496)
- Cutlass Phase 16 Storcli: Partner device ID should be suppressed under ./storcli /c0/eall show for multipath connections(SCGCQ01625114 port of SCGCQ01606780)
- Support only Dell SAS IT Controllers with PERCCLI(SCGCQ01618493 port of SCGCQ01547929)
- Storcli_Aero: Storcli not able to detect controller at EFI shell without Avago MR driver(SCGCQ01600151 port of SCGCQ01595698)
- Storcli returns error for show file commands when parsing MR images eventhough the command was successful(SCGCQ01600149 port of SCGCQ01529009)
- Detailed status is not displayed on locating a drive which is not connected to IT card(SCGCQ01599519 port of SCGCQ01571154)
- storcli controller show all lists EPD's in VD list(SCGCQ01599486 port of SCGCQ01556595)
- Spell error in /call/dall split mirror output(SCGCQ01599464 port of SCGCQ01595709)
- Unified StorCLI 7.6 : Read SBR fails with pre-ventura controllers(SCGCQ01539390 port of SCGCQ01539360)
- Implemented to display the full Model number of the SATA drive when connected to an IT controller(SCGCQ01528939 port of SCGCQ01525764)
- Libmod: checking-in the changes forLibmods for SCGCQ01525764(SCGCQ01528935 port of SCGCQ01528886)
- Storcli display Operating System without space for Linux version(SCGCQ01479250 port of SCGCQ01478526)
- Adding excludevd option to the help file of patrolread command(SCGCQ01445710 port of SCGCQ01443435)
- Updating readme file(SCGCQ01294583 port of SCGCQ01294570)
- SLT displays XYRATEX enclosure many fields information as "Unsupported", when we fire a command Get Enclosure Status(SCGCQ01003523 port of SCGCQ00950453)
- Libmod Changes for Defect SCGCQ01595640 (CLI does not report Serial number for Lenovo D1224 Enclosure)(SCGCQ01714307 port of SCGCQ01664412)
- Storcli_Aero: unable to set sasadd methodport on IT controller(SCGCQ01628094 port of SCGCQ01609234)
- Update help contents for jbod delete(SCGCQ01625945 port of SCGCQ01624605)
- Un-supported command displayed for "storcli64.exe /call show sasaddress"(SCGCQ01620412 port of SCGCQ01619562)
- Commands "/call/all" return inappropriate message or segfault when both MR and IT controllers are connected(SCGCQ01599483 port of SCGCQ01561703)
- Profile Management: Storcli - Add support for WB bit in profile management show(SCGCQ01454856 port of SCGCQ01445628)
- Instance Validation is failing for mentioned commands.(SCGCQ01445724 port of SCGCQ01415355)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show all" JSON output.(SCGCQ01436736 port of SCGCQ01423447)
- Application crashes while executing storcli64.exe /c0/dall set hidden=on(SCGCQ01599467 port of SCGCQ01571256)
- Storcli PR help execution delay is missing when PR running continuously(SCGCQ01537216 port of SCGCQ01534552)
- Change in RAID levels displaying in controller show all command(SCGCQ01511611 port of SCGCQ01509578)
- Upgrading the ncurses library from 5.4 to 6.0 in view of security vulnerabilities(SCGCQ01500111 port of SCGCQ01499900)
- DriveID and errormsg are coming improper on drive POH command when failed(SCGCQ01447688 port of SCGCQ01443683)
- Instance Validation Failed between "controller-freespace-schema.json" and "show freespace" JSON output.(SCGCQ01430044 port of SCGCQ01414749)
- syntax error while executing "storcli64.exe /c0 get firmware ? "(SCGCQ01620437 port of SCGCQ01618675)
- controller show all command is not listing the Battery information(SCGCQ01599459 port of SCGCQ01561689)
- Incremented devicename is programmed for all the phy's in IT controller(SCGCQ01599449 port of SCGCQ01548481)
- Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01526326 port of SCGCQ01526321)
- Unified StorCLI 7.0.1 : Programming VPD to MPB regions(SCGCQ01500006 port of SCGCQ01336460)
- Unified StorCLI 7.0.1 : Programming VPD to MPB regions(SCGCQ01500000 port of SCGCQ01336460)
- Instance Validation Failed between "controller-properties-schema.json" and "show" json output.(SCGCQ01452142 port of SCGCQ01451156)
- Updating pre-ventura SBR fails with "hwdevice" command(SCGCQ01438351 port of SCGCQ01438214)
- CLI does not report Serial number for Enclosure.(SCGCQ01714296 port of SCGCQ01595640)
- Get VPD from MPB region is failure, but overalll status shows success(SCGCQ01599481 port of SCGCQ01589618)
- Unconfigured Good PD is showing as belonging to Disk Group 0.(SCGCQ01525774 port of SCGCQ01520567)
- Controller should not be reset after firmware download in CLI for SAS 3.5 Controllers(SCGCQ01500132 port of SCGCQ01399793)
- Updating the Diag results as per new API changes(SCGCQ01537265 port of SCGCQ01537255)
- Storcli show preservedcache displays incorrect VD size on a missing VD(SCGCQ01500316 port of SCGCQ01447792)
- Assign VDs suboption in cachecade VD creation is not assigning the intended VDs.(SCGCQ01456036 port of SCGCQ01419754)
0007.0409.0000.0000- Moderate Impact/Low Probability of Occurrence
-------------------
fixes:
- Profile Mgmt API Changes.(SCGCQ00883008)
- MR_RAID_CTX_G35 has one too many bits.(SCGCQ00886417)
- Reintroduce numSGEExt Field in Raid Context for Invader to support 1MB IO.(SCGCQ00927738)
- The code had events with repetitive ID and some structures clashing.(SCGCQ00948535)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23.(SCGCQ01001936)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23 has been added back again into adapteroperations 4.(SCGCQ01014835)
- 800C error when execting Get MFC default function.(SCGCQ01037840)
- StorCLIO states wrong OS version for Windows 2016.(SCGCQ01274715)
- PH4 StorCLI -Cutlass-9305-16e FW download failed on Linux/Windows OS platforms.(SCGCQ01311728)
- Erase [excludemfg] file=<> command hangs when executed on non-op/jumpered/OCR disabled operational MR Ventura controllers.(SCGCQ01311846)
- Fixing Error Handling issues and Resource leak.(SCGCQ01319395)
- Fix for Libmod files having potential loop errors.(SCGCQ01320336)
- Cisco - CSCvd90485 - StorCLI error message incorrect when disabling LargeIO support.(SCGCQ01322003)
- EFIStorcli(1.21.12):Number of blocks in VD info is blank when queried for VD info from EFIStorcli.(SCGCQ01355452)
- Factory command is deducting the remanfacturing license even for the first time manufacturing.(SCGCQ01364604)
- Updated the Help.(SCGCQ01375059)
- controller show all command is not listing the JBODs when controller is in JBOD personality.(SCGCQ01383816)
- Controller mode reported as "Undefined" in JBOD mode in show profile output.(SCGCQ01384238)
- storcli is giving error when issuing the command dall show mirror.(SCGCQ01384690)
- Misleading message "Reboot" when erase or completeflash done in MR ventura.(SCGCQ01385373)
- storcli craches with drive show all command for some specific SATA drive.(SCGCQ01385425)
- Fixing out of bounds in libmods.(SCGCQ01385430)
- StorCli should display 128 byte inquiry for drives connected to IT controller including tape.(SCGCQ01388177)
- Save and restore with spanned volumes is throwing an error array index invalid.(SCGCQ01388543)
- PH5 StorCLI - Pre-Alpha - Show all reports NVMe drive linkspeed as "UNKNOWN".(SCGCQ01392511)
- Strocli: controller-shutdown-restart-schema.json is not in JSON format.(SCGCQ01412756)
- Storclio and storclif dispays windows version wrong for Windows 10 OS.(SCGCQ01413011)
- Storcli: Instance Validation Failed between "controller-sgpioforce-schema.json" and "set sgpioforce" JSON output.(SCGCQ01413017)
- Storcli: Instance Validation Failed between "controller-properties-schema.json" and "show" json.(SCGCQ01413239)
- Not even or regular in pattern of drive order display in storcli.(SCGCQ01415875)
- Storcli: Instance Validation Failed between "controller-profile-schema.json" and "show profile" JSON.(SCGCQ01423458)
- Port linkspeed is displayed in a different JSON object for NVMe drives.(SCGCQ01436920)
- PERC10 - VD is deleted after discarding preserved cache with CLI.(SCGCQ01300897)
- Need to handle FW return code change for profile management success case.(SCGCQ01307320)
- Unified StorCLI 7.3 : Fixing resource leaks - Part 1.(SCGCQ01319405)
- PH4 Ventura PA - StorCLI - show command prints wrong information for Fury C0 in OEL6.8.(SCGCQ01321477)
- Non-operational state of FW when EFI driver is absent causing segmentation fault.(SCGCQ01324749)
- CLI reports failure when issuie DPM commands.(SCGCQ01333085)
- PH4 Ventura - StorCLI - Indentation errors observed in output while programming invalid length VPD file.(SCGCQ01346041)
- Fixing unchecked return values.(SCGCQ01385377)
- Tape drive connected to MR controller should not take NVMe speeds in to consideration.(SCGCQ01388610)
- Battery Capacitance is displayed incorrectly across different applications.(SCGCQ01389922)
- LinkSpeed is unknown for PCIe devices under Port Information headline.(SCGCQ01404583)
- Storcli: Instance Validation Failed between "controller-eghs-schema.json" and "set eghs" JSON output.(SCGCQ01412764)
- Storcli: Instance Validation Failed between "controller-securitykey-schema.json" and "set securitykey" JSON output.(SCGCQ01412948)
- Storcli: Instance Validation Failed between "controller-time-schema.json" and set time json.(SCGCQ01413222)
- This is a syntactical error where a comma was added.(SCGCQ01414744)
- Storcli: Additional string displayed in "Show wbsupport" output.(SCGCQ01415208)
- Instance Validation is failing for mentioned commands.(SCGCQ01415355)
- Instance Validation Failed between "controller-detailed-properties-schema.json" and "show all" JSON output.(SCGCQ01423447)
- Second OCR request not getting triggered, fired when first OCR request about to finish, but O/P shows success.(SCGCQ01290216)
- StorCLI - Show command thorws error "failed to get information from host" in APM (ARM) CentOS.(SCGCQ01321460)
- Unified StorCLI 7.3 : Validate data to be read for controller recovery commands.(SCGCQ01359018)
- IIC mode string was used to append in case of error. I2C must be used.(SCGCQ01392046)
- Storcli 07.403.00.00 is showing Linkdown for all Phys in c0/pall show command.(SCGCQ01404219)
- Storcli: Instance Validation Failed between "controller-events-schema" and "delete events" JSON output.(SCGCQ01410438)
- Storcli: Instance Validation Failed between " controller-termlog-schema" and "delete termlog" JSON output.(SCGCQ01411534)
- Storcli: Instance Validation Failed between "controller-flushwriteverify-schema.json" and "set flus how riteverify" JSON output.(SCGCQ01412771)
- Strocli: controller-ASO-schema.json is not in JSON format.(SCGCQ01413261)
- Instance Validation Failed between "controller-ASO-schema.json" and "show ASO" json.(SCGCQ01430237)
- Updating pre-ventura SBR fails with "hwdevice" comman.(SCGCQ01438214)
- Adding excludevd option to the help file of patrolread command.(SCGCQ01443435)
- MR 7.2:PPC : StorCLi throws error while loading the saved configuration.(SCGCQ01273381)
- PH4 StorCLI - Segmentation fault observed with show command when fury/cutlass/marlin connected in FreeBSD11.0.(SCGCQ01312757)
- Unified LibMods 7.3 : Fixing resource leaks and missing return statments - Part 2.(SCGCQ01319407)
- Changing of PatrolRead Excludevd property from cli.(SCGCQ01348042)
- CLI is not showing Insight Drives with correct Enclosure/Chassis position.(SCGCQ01373639)
- Removing the memory leaks in dequelog command.(SCGCQ01411544)
- Storcli: Instance Validation Failed between "controller-coercion-schema.json" and "set coercion" JSON output.(SCGCQ01412758)
- Strocli: controller-HDD-SSD-thermalpollinterval-schema.json is not in JSON format.(SCGCQ01412934)
- Non-array delete for objects: destructors will not be called for objects in the array leading to unexpected behaviour.(SCGCQ00804672)
- Reverting back SL_MAX_OS_DRIVE_COUNT value to 300.(SCGCQ01114306)
- Fixing Out of Bounds access and Resource leak.(SCGCQ01304875)
- Inconsistencies between the applications for manage link speed.(SCGCQ01389856)
- Storcli: Instance Validation Failed between "controller-supportssdpatrolread-schema.json" and set supportssdpatrolread json.(SCGCQ01413106)
- Storcli: Instance Validation Failed between "controller-bios-schema.json" and "show bios" JSON output.(SCGCQ01413263)
- Assign VDs suboption in cachecade VD creation is not assigning the intended VDs.(SCGCQ01419754)
- StorCLI: Spindown help syntax is misleading.(SCGCQ01421610)
- Storcli shows two controllers in the system though you have only one cotntroller in the system.(SCGCQ00690355)
- StorCLI Device Interface Information field doesn't reflect inteface of actual device attached to an IT controller.(SCGCQ01352149)
- Perccli Snapshot is Enabled error when deleting VDs.(SCGCQ01378900)
- Correcting yacc rule for bbus show gasguage data command.(SCGCQ01389891)
- Strocli: controller-config-schema.json is not in JSON format.(SCGCQ01412748)
- Strocli: controller-detailed-properties-schema.json is not in JSON format.(SCGCQ01413255)
- DriveID and errormsg are coming improper on drive POH command when failed.(SCGCQ01443683)
- Correcting yacc rule of slaveaddress for command hwdevice.(SCGCQ01389890)
- Storcli: Instance Validation Failed between "controller-personality-schema.json" and "set_personality" JSON output.(SCGCQ01412943)
- Storcli: Instance Validation Failed between "controller-smartpollinterval-schema.json" and "set smartpollinterval" json.(SCGCQ01413018)
- Storcli: Instance Validation Failed between "controller-flushwriteverify-schema.json" and "show flushwriteverify" JSON.(SCGCQ01423452)
- The structure name is changed from oob_i2c to oob to avoid compilation failure in OOB SL.(SCGCQ01015024)
- storclif64 can not create prl11 across 2 enclosure using 32 pds.(SCGCQ01295289)
- StorCLI crashes when VPD file with VPD_Length 0 is tried to update.(SCGCQ01340557)
- Removing the NMR command for setting SCAPVPD.(SCGCQ01389451)
- Storcli: Instance Validation Failed between "controller-perfmode-values-schema.json" and "set perfmode" JSON output.(SCGCQ01412938)
- Instance Validation Failed between "controller-freespace-schema.json" and "show freespace" JSON output.(SCGCQ01414749)
EnhancementRequests:
- MPI2: Add TargetModeAbort by initiator device handle.(SCGCQ00337167)
- New fault code for routine synchronous reset.(SCGCQ01264142)
- MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually.(SCGCQ00574358)
- MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag).(SCGCQ00414050)
- MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply.(SCGCQ00396414)
- MPI2: Add OEM Identifier to BIOS Page 1.(SCGCQ00357228)
- MPI2: Use Slot Information during Port Enable Event Replay option.(SCGCQ00356796)
- MPI2: Add new TargetModeAbort AbortType to only abort Command IUs.(SCGCQ00345215)
- MPI v2.6: Additional request and reply descriptor formats.(SCGCQ00259613)
- API changes for CR55 - PCIe lane/link speed.(SCGCQ01222700)
- API change for Simplified RAID10 Creation.(SCGCQ01222698)
- API Changes Required for Specific OEM Backplane functionality.(SCGCQ01218406)
- API changes for PR SCGCQ01139678 - Method for determining bad ONFI flash in storcli.(SCGCQ01215334)
- MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0.(SCGCQ01213028)
- MPI 2.5: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01208954)
- API changes for PR SCGCQ01127742 - Isolating faulty cable issue from bad drive issue.(SCGCQ01203751)
- MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP.(SCGCQ01180886)
- MR 6.12 - Add JBOD mode personality to MR_CTRL_PERSONALITY.(SCGCQ01146597)
- MR 7.0: Add supportPdMapTargetId flag in MR_CTRL_INFO and MFI_CAPABILITIES.(SCGCQ01141251)
- MR 6.13: Add API support for TFM/SCAP _MR_BBU_VPD_INFO_FIXED parameters.(SCGCQ01139344)
- MR 6.13: Add a new control command to fetch ROC temperature data over I2C.(SCGCQ01137627)
- MR 7.2: Add API support to make application work with Cachecade3.0 on Ventura (Public).(SCGCQ01114969)
- MPI 2.5: Add new connector types.(SCGCQ01085073)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ01002367)
- MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout".(SCGCQ00996127)
- MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1.(SCGCQ00853162)
- MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable.(SCGCQ00791885)
- MPI 2.5: add WWID to BIOS Page 3.(SCGCQ00785208)
- MPI 2.5: update copyright info.(SCGCQ00728066)
- MPI 2.5: BIOS Page 1 additions.(SCGCQ00700829)
- MPI 2.5: distribute Target Command Buffers Received across multiple reply queues.(SCGCQ00685820)
- MPI 2.0: Add product-specific Flag bit to Clean Tool.(SCGCQ00569175)
- Add type BIOS for HashImageType.(SCGCQ00566306)
- Identify physical location of a target device.(SCGCQ00523879)
- MPI 2.5: add reserved fields to IO Unit Page 7 for future use.(SCGCQ00477817)
- MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps".(SCGCQ00471293)
- MPI 2.5: Signed images for FWDownload.(SCGCQ00469990)
- MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL.(SCGCQ00438437)
- MPI 2.5: Toolbox Console Text Display Tool.(SCGCQ00415512)
- Allow Protection Information bit for IR Volume Create.(SCGCQ00385306)
- MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply.(SCGCQ00357551)
- MPI 2.6: add PCIe Device Config Pages.(SCGCQ00345271)
- MPI 2.6: PCIe Switch Config Pages.(SCGCQ00345270)
- MPI 2.6: PCIe Topology Change List Event.(SCGCQ00345266)
- MPI 2.6: add PCIe Event Data (Generic), PCIe Device Status Change Event, and PCIe Enumeration Event.(SCGCQ00345260)
- MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors.(SCGCQ00338506)
- MPI 2.6: PCIe IO Unit Page 0 & 1 definitions.(SCGCQ00336383)
- MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1.(SCGCQ00310439)
- MPI 2.6: update SGL chapter to include PCIe.(SCGCQ00294131)
- MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request.(SCGCQ00294055)
- MPI 2.6: NVMe Encapsulated request.(SCGCQ00264759)
- MPI 2.6: SOP Encapsulated request.(SCGCQ00264755)
-.(SCGCQ01421997)
- Controller should not be reset after firmware download in CLI for SAS 3.5 Controllers.(SCGCQ01399793)
- RPM -verify report error after installing storcli RPM package for linux.(SCGCQ01373354)
- Adding the JBOD personality with EPD passthrough support.(SCGCQ01368469)
- Added the support for EPD-PT creation and operations on a EPD-PT.(SCGCQ01368465)
- List pending profile details of the controller.(SCGCQ01346308)
-.(SCGCQ01291037)
- MPI 2.6 Add Atomic Request Descriptor capability.(SCGCQ00227735)
- MPI 2.6: add IO Unit Control Request.(SCGCQ00345258)
- MPI 2.6: PCIe Link Config Pages.(SCGCQ00345272)
- MPI 2.6: Enclosure Management.(SCGCQ00345273)
- Device Info field for PCIe devices.(SCGCQ00353339)
- MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request.(SCGCQ00360843)
- MPI 2.6: new family values for ProductID fields.(SCGCQ00360952)
- MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11.(SCGCQ00363600)
- Modified address space bits.(SCGCQ00397136)
- MPI 2.6: Add PCIe IO Unit Page 4.(SCGCQ00397563)
- MPI 2.6: Add board power fields to IO Unit Page 7.(SCGCQ00397572)
- MPI 2.6: Add support for SAS Persistent Connections.(SCGCQ00397577)
- MPI 2.6: Add NVMe SGL support.(SCGCQ00398256)
- MPI 2.6: Add NVMe SGL support to IEEE SGL.(SCGCQ00432541)
- MPI 2.6: System Interface Register Set update.(SCGCQ00464402)
- Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request.(SCGCQ00480292)
- MPI 2.6: shutdown operation for IO Unit Control Request.(SCGCQ00496998)
- MPI 2.6: Add supported link rates and widths for PCIe devices.(SCGCQ00564281)
- MPI 2.6: Add additional NVMe AccessStatus codes.(SCGCQ00574070)
- MPI 2.6: Add BootFlags field to Firmware Image Header.(SCGCQ00601869)
- MPI 2.6: Add new FLASH region types.(SCGCQ00619371)
- MPI 2.6: Added an additional signature value for the firmware image header.(SCGCQ00623271)
- MPI 2.6: additional AccessStatus values for PCIe Device Page 0.(SCGCQ00664957)
- MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages.(SCGCQ00680527)
- MPI 2.6: Extend Task Management - Target Reset Method to include PCIe devices.(SCGCQ00686666)
- MPI 2.6: Add device off flag to SCSI Enclosure Processor messages.(SCGCQ00776177)
- MPI 2.6: New Phy event codes added to Ventura.(SCGCQ00789600)
- MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough.(SCGCQ00813389)
- MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura.(SCGCQ00827088)
- MPI 2.6: add PCI Device ID's.(SCGCQ00828497)
- MPI 2.6: methods to report Active Cable power problems.(SCGCQ00831588)
- MPI 2.6: SRIOV support for PCIe devices.(SCGCQ00852827)
- MPI 2.6: Update Flash Signature..(SCGCQ00852831)
- profile management API.(SCGCQ00867953)
- MPI 2.6: add new feature to control NVMe SGL format.(SCGCQ00872169)
- Mega API modifications needed for RMW-FP and Cache bypass features in Ventura.(SCGCQ00875328)
-.(SCGCQ00878757)
- Merging api_overrides mega_api files with the files in the Mega_API development stream.(SCGCQ00883262)
- MPI 2.6: Update Ventura family device ids to match latest EDS.(SCGCQ00915256)
- MPI 2.6: update Marlin-class device IDs.(SCGCQ00915336)
- MPI 2.6: Remove all SOP references.(SCGCQ00925839)
- Ventura: de-feature AHCI.(SCGCQ00941620)
- MPI 2.6: Remove all AHCI references.(SCGCQ00948258)
- MPI 2.6: Add support for SAS-4 and PCIe-4.(SCGCQ00948955)
- MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0.(SCGCQ00949638)
- MPI 2.6: add LinkNum field to the PCIe Link configuration pages.(SCGCQ00954619)
-.(SCGCQ00987840)
- MPI-2.6: backend PCIe feature initialization status reporting.(SCGCQ01009104)
- MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request.(SCGCQ01013930)
- MPI2.6: Fix defines that are not unique within the first 32 characters.(SCGCQ01015826)
- MPI 2.6: direct reporting of negotiated PCIe link width and speed.(SCGCQ01017027)
- MPI 2.6: Backend SRIS mode enable flag.(SCGCQ01018687)
- MPI2.6: Reserve ExtPageTypes for Dragon.(SCGCQ01020473)
- MR_CTRL_INFO expansion from 2K to 4K.(SCGCQ01023741)
- mega api changes for ibuttonless PR.(SCGCQ01059740)
- MPI2.6: Add x16 PCI support for Marlin family products.(SCGCQ01063009)
- MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page.(SCGCQ01071374)
- Profile Management Changes to support requestedProfileID and optimisedProfile.(SCGCQ01075821)
-.(SCGCQ01082303)
-.(SCGCQ01085954)
- MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout".(SCGCQ01092340)
- MEGA_API Changes to incorporate new IO subtype to support redirect cached IO.(SCGCQ01094549)
- MPI 2.6: Add Sea Arch class and Product IDs.(SCGCQ01116837)
- MR 7.0: Add MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT = 7 to mfi.h file.(SCGCQ01133839)
- MPI2.6: Added new image type and flash region definitions.(SCGCQ01136127)
- MPI 2.6: Add new clean tool options.(SCGCQ01141732)
- MPI 2.6: Add two new reason codes to Active Cable Exception Event Data.(SCGCQ01146583)
- Define CurrentFwNvmePageSize element in new MFI_REG_STATE_EXT3 register.(SCGCQ01188725)
- MR7.1. Add MR API bit to indicate the profile is NVMe Only profile.(SCGCQ01213092)
- MPI2.6: Mfg7 support for arbitrary starting slot number.(SCGCQ01213267)
- MPI 2.6: Add new firmware download type (CBB BACKUP).(SCGCQ01258005)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply.(SCGCQ00988360)
- MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses.(SCGCQ00466819)
- always print StorCLI version information at beginning/top of output.(SCGCQ01396733)
- StorCLI JSON 4.0 compliant schema creation for Contoller level commands.(SCGCQ01365177)
- New command in CLI OEM mode to select either PCIE or I2C as an out of band transport.(SCGCQ01353429)
- Add support to allow Device names greater than 107.(SCGCQ01039328)
- MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs.(SCGCQ00397568)
- MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit.(SCGCQ00884740)
- MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks.(SCGCQ00922213)
- Profile Management: Storcli - Add support for WB bit in profile management show.(SCGCQ01445628)
-.(SCGCQ01428114)
- Add ability to field upgrade CPLD on HBA boards.(SCGCQ01283646)
- Add NVMe device related changes.(SCGCQ01034678)
- Block the MR commands being fired to IT controllers and vice versa from StorCLI.(SCGCQ01315301)
- Unified StorCLI 7.3 : Display serial number information in StorCLI.(SCGCQ01309079)
- Unified StorCLI 7.3 : ARM EFI support to Unified StorCLI.(SCGCQ01292973)
- Unified StorCLI : [Lenovo Purley] Adding tape drive support to Unified StorCLI for IT Ventura controllers.(SCGCQ01351495)
CSETActivities:
- StorCLI firmware download to multiple target devices fails to every other device.(SCGCQ01417390 port of SCGCQ01391339)
- Unified StorCLI 7.3 : Validate data to be read for controller recovery commands.(SCGCQ01399705 port of SCGCQ01359018)
- MR 6.14-CLI: Auto Learn Period Mismatch between CTRL-R and StorCLI..(SCGCQ01396719 port of SCGCQ01391037)
- Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391818 port of SCGCQ00940993)
- The command "Storcli /c0/vall del" its deleting the VDs along with EPDs as well.(SCGCQ01304925 port of SCGCQ00915484)
- Second OCR request not getting triggered, fired when first OCR request about to finish, but O/P shows success.(SCGCQ01300741 port of SCGCQ01290216)
- Cisco - CSCvd49859 - Set VD hidden on a already hidden VD message is not correct from StorCLI.(SCGCQ01298614 port of SCGCQ01295830)
- Mr_6.12_Arm_EFI_CLI:storcli.ef /c0/vall show bbmt dose not display the corrected and uncorrected values.(SCGCQ01293051 port of SCGCQ01059790)
- MR_6.12_Arm_EFI-CLI:storcli.efi /c0/vall set ssdcaching=on/off does not apply for all the Vd's at a time.(SCGCQ01293028 port of SCGCQ01060315)
- MR_6.12_Arm_EFI-Synchronous Exception on running set vpd command with a wrong input file.(SCGCQ01293027 port of SCGCQ01059798)
- Hercules StorCLI: Progress EVents are not logged in StorCLI.(SCGCQ01291546 port of SCGCQ01288785)
- SLT : Requesting user to enter the allocated response length of SMP request page.(SCGCQ01202087 port of SCGCQ01202030)
- Changing ini file name to storelibconfit.ini.(SCGCQ01275669 port of SCGCQ01275496)
- Block OCR after Clearing NVRAM.(SCGCQ01396705 port of SCGCQ01389485)
- ER:SCGCQ00940993-Libmod Changes:Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391828 port of SCGCQ00976651)
- Tape drive connected to MR controller should not take NVMe speeds in to consideration.(SCGCQ01389395 port of SCGCQ01388610)
- Unified LibMod changes for SCGCQ01351495[Tape drive support to StorCLI].(SCGCQ01385205 port of SCGCQ01351565)
- Perccli Snapshot is Enabled error when deleting VDs.(SCGCQ01384442 port of SCGCQ01378900)
- CISCO SQA2 - LR - 1U 10 HDD - StorCLI - /c0/eall/sall start locate throws success message with no LED activity.(SCGCQ01350423 port of SCGCQ01349575 )
- Global Hot Spares shows as TR in storcli DG query when TR is activated on DG.(SCGCQ01332915 port of SCGCQ01047789)
- Correcting error messages for transport errors.(SCGCQ01332859 port of SCGCQ01093152)
- Storcli needs to be fixed for maximum TR info in ctrl show all.(SCGCQ01332851 port of SCGCQ01112673)
- Storclif64 does not return non zero error code on failure.(SCGCQ01320515 port of SCGCQ01318824)
- MR 7.2:PPC : StorCLi throws error while loading the saved configuration.(SCGCQ01318368 port of SCGCQ01273381)
- Need to handle FW return code change for profile management success case.(SCGCQ01318326 port of SCGCQ01307320)
- MR6.12_Arm_storcli.efi:Error Message Wrong on start learn cycle failure scenario.(SCGCQ01293158 port of SCGCQ01039757)
- perccli lists PDs in the wrong order - sometimes.(SCGCQ01292796 port of SCGCQ01290596)
- Storcli shows CV as optimal When Predictive Failure Bit is set.(SCGCQ01392548 port of SCGCQ01392529)
- Storcli shows CV as optimal When Predictive Failure Bit is set.(SCGCQ01392541 port of SCGCQ01392529)
- MR6.12_FW : With spun down PDs and primary path broken, FW does not allow creation of VDs.(SCGCQ01332806 port of SCGCQ01035520)
- Adding a sub option to skip the self-test while reading the POH as per customer request.(SCGCQ01292051 port of SCGCQ01074274)
- MR_6.12_ARM_Storcli.efi:storclio.efi /c0 set pcilinkspeed=3 success and set as 3%.(SCGCQ01293159 port of SCGCQ01058298)
- SLT displays XYRATEX enclosure many fields information as "Unsupported", when we fire a command Get Enclosure Status.(SCGCQ01003523 port of SCGCQ00950453)
- Update Attribution Language - Copyright, Trademark, Confidentiality to Avago.(SCGCQ00793391 port ofSCGCQ00787940)
- StorCLI displays "Next Learn Time" incorrectly.(SCGCQ01345297 port of SCGCQ01344843)
- Factory settings changes for Transport as per new MFC_DEFAULTS in API.(SCGCQ01332916 port of SCGCQ01044891)
- CLI to maintain consistency in the properties/attributes including case between MR and IT.(SCGCQ01309547 port of SCGCQ01308958)
- The command "Storcli /c0/vall del" its deleting the VDs along with EPDs as well.(SCGCQ01305204 port ofSCGCQ00915484 )
- perccli lists PDs in the wrong order - sometimes.(SCGCQ01292797 port of SCGCQ01290596)
- Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391817 port of SCGCQ00940993)
- StorCli should display 128 byte inquiry for drives connected to IT controller including tape.(SCGCQ01388560 port of SCGCQ01388177)
- Factory command is deducting the remanfacturing license even for the first time manufacturing .(SCGCQ01364653 port of SCGCQ01364604)
- Trying to Create Logical disks with UBAD drives gives wrong Failure Message from Storcli.(SCGCQ01358889 port of SCGCQ01356294)
- StorCLI displays "Next Learn Time" incorrectly.(SCGCQ01345296 port of SCGCQ01344843)
- Storcli fails with segmentation fault (core dumped) with foreign import.(SCGCQ01332905 port of SCGCQ01214152)
- C240-M5: Segmentation Fault observed when tried to delete a SWR VD from Version (Max5): 3.1(0.102).( SCGCQ01324969 port of SCGCQ01309488)
- Cisco - CSCvd49859 - Set VD hidden on a already hidden VD message is not correct from StorCLI.(SCGCQ01301733 port of SCGCQ01295830)
- Libmods: Second OCR request not triggered, fired when first OCR request about to finish, but O/P shows success(SCGCQ01290216).(SCGCQ01300727 port of SCGCQ01300721)
- Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01292007 port of SCGCQ00940993)
- ER:SCGCQ00940993-Libmod Changes:Custom PERC CLI for Dell OEM Solutions group.(SCGCQ01391827 port of SCGCQ00976651)
- storcli craches with drive show all command for some specific SATA drive.(SCGCQ01386881 port of SCGCQ01385425)
- Unified StorCLI : [Lenovo Purley] Adding tape drive support to Unified StorCLI for IT Ventura controllers.(SCGCQ01383787 port of SCGCQ01351495)
- Transport command is including all when only shared is requested, where it should be failed.(SCGCQ01332907 port of SCGCQ01093145)
- Libmods: SCGCQ01214152 - Storcli fails with segmentation fault (core dumped) with foreign import.(SCGCQ01332872 port of SCGCQ01249484)
- [Lenovo] Storcli may not be able to show the RAID controller in some special situation.(SCGCQ01392462 port of SCGCQ01389914)
- Storcli SegFault -HUU update utility doesn't detect SBMezz if Foreign Config PD exist.(SCGCQ01332850 port of SCGCQ01155309)
- Erase [excludemfg] file=<> command hangs when executed on non-op/jumpered/OCR disabled operational MR Ventura controllers.(SCGCQ01315413 port of SCGCQ01311846)
- PH4 StorCLI -Cutlass-9305-16e FW download failed on Linux/Windows OS platforms.(SCGCQ01311820 port of SCGCQ01311728)
- MR6.12_Arm_Storcli.efi:No error message shown when deleting securitykey fail.(SCGCQ01293161 port of SCGCQ01039756)
- MR6.12_Arm_EFI-CLI:Having multiple Raid volumes created,CLI lists extra entries and all operations on VD’s fails thereafter.(SCGCQ01293053 port of SCGCQ01047493)
0007.0209.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------
Fixes:
- MegaCli and StorCli can not manage both Liberator (and prior) and TB controllers in the same system under FreeBSD with the mf(SCGCQ00355536)
- Update VD emulation feature in StorCLI Libmods module to sync with latest APIs.(SCGCQ00357913)
- StorCLI does not display drive information behind the Blackjack (Alta) interposer correctly(SCGCQ00357948)
- In paged view the text " Press Enter to continue" should be changed to " Press any key to Continue"(SCGCQ00359629)
- Code clean up in libmods and sysefi files are added(SCGCQ00359998)
- Storcli is returning error with show(SCGCQ00360040)
- StorCLI: Not able to set pr property includessds as onlymixed on Liberator cacheoffload controller(SCGCQ00360814)
- iMr_Fury_StorCli:4K Drive size shown wrong in Esxi4.1U3(SCGCQ00362216)
- storcli /c0/d0 show " in that legend missing for "Dgrd/pdgd/Onln/ofLn/Rbld"(SCGCQ00362717)
- The legend for the PD List table exceeds 80 char limit.(SCGCQ00363455)
- storcli query for displaying controller properties is showing status , as failure.(SCGCQ00363522)
- iMR_Inv_6.1:StoreCLI- StoreCLI reports wrong Emulation type for VDs(SCGCQ00364097)
- StorCLI failed to delete a VD that is just created under Windows 2008(SCGCQ00364248)
- Reports wrong diskgroup size while querying controller level properties(SCGCQ00364622)
- UEFI, the O/P of "Current Controller Date/Time" & "Current System Date/time" are not in proper format(SCGCQ00364735)
- Storcli displays incomplete serial number for some SSDs(SCGCQ00366000)
- Certain controller features displayed under "show all" exceeds 80-char limit.(SCGCQ00372155)
- StorCLI crashed when run on a Windows 2008 64-bit with 24GB of RAM and 66 drives attached(SCGCQ00374735)
- StorCli shows Power Saving Option as enabled, despite IBM Flatwood controller having power saving option completely disabled.(SCGCQ00377364)
- portings of AdpRestart command(SCGCQ00378135)
- StorCLI-Legacy:'adpbootdrive get' fails to get bootdrive information.(SCGCQ00378828)
- Not able to get paged view of StorCLI output on VM-Ware Platform(SCGCQ00379104)
- Cfgclr command fails without force option in Sparc OS(SCGCQ00396303)
- storcli crashes on having a non PI drive and trying to create pi vd on all the drive(SCGCQ00413789)
- EFI_ Storcli: Cannot set vpd file on controller, EFI hangs and cannot proceed for further operations until reboot(SCGCQ00423832)
- Megacli crashes after invoking any command in SGI system with one 9280-8e and 2 quad port qlogic FC cards.(SCGCQ00438350)
- Onfi_patch_6.0:Firmware crashed @Line 244 in ../../raid/1078int.c for entering into CTRL-R with Pinned cache in R60 and R6.(SCGCQ00442610)
- SWR_1.34(SCGCQ00442652)
- Raptor_Galaxy:State of the Shielded Drive is not displayed using storcli command(SCGCQ00467502)
- Raptor_Galaxy_Tencent:Tencent Storcli detecting the H710 PERC card.(SCGCQ00475583)
- Storcli internal errors should return with 1001, but its coming as -1(SCGCQ00479843)
- Try to create a Exclusive VD, but after creation it still shows as Shared VD.(SCGCQ00484560)
- MR6.2 : Storcli shows incorrect "Bus" information when "/c0 show all" is run(SCGCQ00518201)
- Unable to make R10 through Ctrl R using 4k drives(SCGCQ00518579)
- PPC64 :: MR Liberator :: Storcli Version 1.09.01 is showing wrong Creation Date and Time in VD properties(SCGCQ00569935)
- MR_Inv_6.3_PPC:Storcli- Retreiving LDBBM info through storcli is failing on SLES11 SP2 PPC64(SCGCQ00574835)
- "/cx/ex show phyerrorcounters" gives core dump on freeBSD 32 and 64 bit.(SCGCQ00644123)
- Storcli : unable to set patrol read delay(SCGCQ00645195)
- MR6.4_StorCLI_240VD: StorCLI crashes on issuing /c1 set cc=conc delay=10 starttime=2014/12/12 12 excludevd=0(SCGCQ00649324)
- Storlib header file checkin and make compatible changes in CLI code.(SCGCQ00653742)
- StorCLIO_1.09.09 : Not able to set subOEMid in Rhel 5.10 x64 bit.(SCGCQ00674131)
- While creating cachecade vd with one SAS-SSD;Raid 1 option is also enabled(SCGCQ00712171)
- H330: Firmware Crash is hit while creating the Raid1 vd without drives selected(SCGCQ00725192)
- After Rebuilding, DHS and Expand VD operations failed to update as per VD properties(SCGCQ00730505)
- 6.6_StorCli: StorCli lists all cascaded enclosures at position 0.(SCGCQ00756647)
- FW breaks in iMR when excluding VD's from CC(SCGCQ00758770)
- SupportMaxRate SATA is not listed in PD allowed operations.(SCGCQ00759178)
- SED adapterOperation detailed is not shown in detailed show controller properties(SCGCQ00759183)
- Adapters are not listed in sorted order.(SCGCQ00759969)
- MR6.6: Segmentation fault (Core Dumped) in CLI when setting any invalid value for PR start time(SCGCQ00760398)
- /c0 show all does not list hwCfg information as compared to MegaCLI.(SCGCQ00760752)
- Storclio : Different error code is coming for 'set pcilinkspeed' in VMware 4.1U3(SCGCQ00762663)
- StorCLI is not updated with the error Message for all new MFI_STAT added in mfistat.h(SCGCQ00765712)
- StorCLI VMware Binary not displaying detailed description for phyerrorcounters of enclosures(SCGCQ00765762)
- StorCLI shows CacheBypass Size and CacheBypass Mode feature enabled against a VD which is associated with a CacheCade VD(SCGCQ00772243)
- Active operation(s) is coming as none when virtual drive erase is in progress.(SCGCQ00779789)
- MR6.6:StorCLI shows incorrect information about "Cache Vault Flash Size"(SCGCQ00782882)
- "cpybck" help is not coming in Legends(SCGCQ00784808)
- VD level hide/unhide is not possible through storcli in PPC(SCGCQ00785400)
- MFCdefaults : DisableHII option needs to be include in getShowDefaults()(SCGCQ00792232)
- Comparing an array to null is not useful: "rawSmartData != NULL"(SCGCQ00793374)
- MR_6.7_STROCLI: Command "./storcli64 /c0/ex/sx reset phyerrorcounters" fails in RHEL6.6 PPC64(SCGCQ00794394)
- .(SCGCQ00800878)
- Deallocation of the same memory more than once(SCGCQ00802031)
- Memory leak happening in failure case since not freeing before returning error code.(SCGCQ00804588)
- Out-of-bounds access and array delete misuse(SCGCQ00804680)
- MR_6.7_ Storcli: "Storcli /cx/eall/sall show " gives no enclosure found if two enclosures are connected in multipath scenario(SCGCQ00805547)
- Not able add new VD in Drive Group(SCGCQ00813314)
- MR_6.7: Storcli Command "./storcli /c0/v2 set accesspolicy=RmvBlkd " fails for a blocked source VD.(SCGCQ00814939)
- Storcli cannot create R10 in iMR with 6 or 8 drives per span.(SCGCQ00827049)
- Storcli crashes instead of showing error message on enabling caching on Source VDs and C(SCGCQ00827299)
- storcli /call show all fails with "command invalid"(SCGCQ00830269)
- New PD_Degraded media events are not logging correctly in PPC(SCGCQ00837342)
- Profile Mgmt API Changes(SCGCQ00883008)
- MR_RAID_CTX_G35 has one too many bits(SCGCQ00886417)
- Reintroduce numSGEExt Field in Raid Context for Invader to support 1MB IO(SCGCQ00927738)
- The code had events with repetitive ID and some structures clashing(SCGCQ00948535)
- Controller detection fails in EFI environment with MR Ventura card(SCGCQ01001372)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23(SCGCQ01001936)
- CtrlInfo.adapterOperations3.supportProfileChange is missing in Ventura Dev API baseline dated 2015-12-23 has been added back again(SCGCQ01014835)
- 800C error when execting Get MFC default function(SCGCQ01037840)
- ThinkServer: Cyborg [Purley] Sotrcli (007.0022.0000.0000) cannot show the correct PCI bus/dev/func number for Invader and Ven(SCGCQ01087936)
- Serial Number for drives were having spaces when displaying in Storcli(SCGCQ01126284)
- No ISE Capable field(SCGCQ01148693)
- MR7.1_NVMe:Segmentation fault seen on storcli while generating controller info with preserved cache(SCGCQ01193175)
- Ventura-Beta: Storcli/Storclif utilities hit Segmentation fault when foreign configuration is present(SCGCQ01198698)
- Fixing Resource leaks(SCGCQ01205356)
- resource validation before de referencing(SCGCQ01206104)
- Fixing resource leaks in libmods(SCGCQ01208044)
- Fixing resource leak and pointer to local variable coverity defect in libmods(SCGCQ01209393)
- Fixing Logically dead code and Wrong size arguments in CLI(SCGCQ01209414)
- Unified Libmods StorCLI 7.1:Fixing resource leaks-Part 4(SCGCQ01209473)
- Fix for resource leak in system config show(SCGCQ01210133)
- MR7.1_NVMe: comma missing between RAID10 and RAID60 in the RAID Level Support at /c0 show all output(SCGCQ01214415)
- Storcli does not show "NVME" in supported Drives.(SCGCQ01215383)
- some of the drive properties is not shown properly on querying the drive info through storcli(SCGCQ01229923)
- Unified StorCLI 7.1:Incorrect usage of STORCLIO and STORCLIF macros(SCGCQ01234217)
- NVMe PD SMART DATA shows all 0's(SCGCQ01236052)
- StorCLIO states wrong OS version for Windows 2016(SCGCQ01274715)
- Individual Phy information on an IT works, when given with multiple Phys it says "Unsupported Command".(SCGCQ01275381)
- When invalid enclsoure is specified as user input , the output is not correct(SCGCQ01275687)
- IT show all command displays Physical Drive Information headline wihtout table when no drive is connected(SCGCQ01276688)
- Unified StorCLI 7.2:Windows only:Drive properties headline gets truncated during drive show all command(SCGCQ01280928)
- StorCLI: Not able to detect Liberator Controller on FreeBSD 9.0(64-bit)(SCGCQ00362421)
- PCI Info for FreeBSD needs to be indicated as "N/A"(SCGCQ00365632)
- Vmware CLI fails to set the phy linkspeed(SCGCQ00371445)
- System halts on issuing storcli commands in EFI Environment.(SCGCQ00374336)
- PERC9:Storcli ld info command displays R10 vd Span Depth to 1.(SCGCQ00374979)
- StorCli_MR: While Creating RAID1 with four drives command facing the "C0:BAIL_OUT at line 1354" on Flatwood Board(SCGCQ00394883)
- core dump while issuing storcli command ./storcli /c0/fall show all.(SCGCQ00448094)
- Some Numeric values in CLI o/p comes in Hex format(SCGCQ00481474)
- Unable to insert a drive after setting a drive as 'Missing' .(SCGCQ00490620)
- Some sparc structures missing for storcli.(SCGCQ00504585)
- MR Liberator : PPC SERVERGY Server : MonTask: line 541 in file ../../raid/raidpci.c(SCGCQ00567761)
- PPC64 :: MR Liberator :: All commands of StorCli is failing with segmentation fault after creating a GlobalHotSpare(SCGCQ00579658)
- storecli reports wrong size on 3000MB VD(SCGCQ00644545)
- Cannot create a VD smaller than 800MB with 4K drives(SCGCQ00649962)
- MR6.4: Storcli show command does not display all the controllers plugged into the server(SCGCQ00653672)
- Add support bits for uneven-span and SSHA support(SCGCQ00755063)
- MR_6.6_Storcli: Storcli reports supercap state 'unknown' while learn is happening on the controller.(SCGCQ00758101)
- Exception with command /co show badblocks or "storcli /cx flasherase"(SCGCQ00758924)
- SSM-FLASh drives property is displayed for regular drives.(SCGCQ00759290)
- Support details are not shown in /c0 show all for discard cache (stalling LD deletion)(SCGCQ00759959)
- MR_6.6: StorCLI showing incorrect value for next Schedule time for consistency check after disabling the CC(SCGCQ00760385)
- MR 6.6 Prealpha2 Storcli:Similar PCI address(BDF number) is displayed for multiple controllers connected to FreeBSD 9.3.(SCGCQ00761937)
- StorCLI /c0 show all command does not reflect the discard vd delete filed(SCGCQ00764658)
- StorCLI shows CacheBypass Size and CacheBypass Mode feature enabled against a CacheCade VD(SCGCQ00765714)
- StorCLI shows wrong "Number of blocks" for a 65.5TB VD size(SCGCQ00765759)
- Patrol read delay is showing wrong value when set to continuous(SCGCQ00767347)
- Showing wrong creation date for Autoconfigured virtual drives(SCGCQ00767363)
- Storcli errors are printing in a different line.(SCGCQ00771626)
- Storcli has option to set PR maxconcurrentpd but show is not present(SCGCQ00772302)
- vpdpage should be read from 4 bytes to get serial number of drive(SCGCQ00772332)
- GB scale to be added while showing CacheCade size in CLI(SCGCQ00778577)
- MR6.6_CLI_FreeBSD: Displaying incorrect Driver name(SCGCQ00779800)
- CTRL-R:2 iMR Card in same System hitting Montask(SCGCQ00783357)
- Readability : Output string need to be updated for supportForceTo512e in show all command(SCGCQ00792202)
- The HDD firmware revision is shown blank for few drives connected.(SCGCQ00793761)
- MR_6.7_STROCLI: "./storcli64 /c0/ex show phyerrorcounters" gives segmentation fault in RHEL6.6 PPC64(SCGCQ00794393)
- Explicit null dereferenced in rmdatamf.cpp causing wrong result.(SCGCQ00795335)
- Resource leak(SCGCQ00804745)
- .(SCGCQ00811452)
- Unified StorCLI:EFI:Duplicate instances of Controller gets added to the ControllerIdList pointer(SCGCQ00936672)
- Unified StorCLI 7.1:Coverity fixes(SCGCQ01206205)
- Fix for profile management support check bit(SCGCQ01208103)
- Unified StorCLI 7.1:Fxing resource leaks-Part 3(SCGCQ01209411)
- Unified Storcli: Fixing resource leak issues(SCGCQ01209413)
- SAS3.5 Ventura(SCGCQ01219196)
- Discrepancy while installing and uninstalling of latest Storcli Package(SCGCQ01234153)
- StoreCLI unified for Ventura version cannot display direct attached disk serial number information.(SCGCQ01280169)
- pall compare shows the current linkspeed on MR controllers(SCGCQ01282376)
- Need to handle FW return code change for profile management success case(SCGCQ01307320)
- MegaCLI adpgetpciinfo returns a static Bus Number value "17d0"(SCGCQ00357263)
- iMR_Inv_6.1:StorCLI- StorCLI does not show 'Unsupported/Blocked' state for 4K drives even though FW is not supporting 4K(SCGCQ00384644)
- StorCli_MR: While creating VD using default values FW allows read policy as"Ra=Read Ahead Adaptive" as against PR-317400(SCGCQ00397663)
- MR6.1: Hamlin: Is VD Emulated=Yes when emulationType=1(SCGCQ00424978)
- storcli /c0 show is not listinf SWR controller(SCGCQ00454971)
- Pcli: Pcli crashes while try to set securitykey for controller.(SCGCQ00471116)
- Raptor Galaxy : Storcli(SCGCQ00475562)
- Command "./Storcli /call/eall/sx set offline" fails with ERRcode1001 and ERRmsg drive not found.(SCGCQ00503981)
- Wrong size of CacheCade VD is getting displayed after making one PD offline(SCGCQ00505771)
- Some characters missing while querying for VD properties with having 64 VD's on a controller.(SCGCQ00529763)
- Storclio_1.09.00:Fails to set SubOEMID on Solaris OS .(SCGCQ00568073)
- MR_Inv_6.3_PPC:Storcli-WWN is showing blank for SAS PDs on SLES11 SP2 PPC64(SCGCQ00572800)
- PPC64 :: MR Liberator :: ./storcli64 /c0 show dequeuelog file command failing with segmentation fault(SCGCQ00581416)
- MR : on querying PR status, storcli hits segmentation fault.(SCGCQ00601775)
- /c0 set cc=conc command fails with iMR card.(SCGCQ00603174)
- storelib header file changes porting(SCGCQ00609942)
- MR_6.4_StorCli_EFI: Storcli.efi crashes for iMR card.(SCGCQ00674023)
- Storcli doesn't show SN of Samsung SSD 200/400/800 in SWRAID version 1.32(SCGCQ00674969)
- storcli /c0 show all is not displaying "support vd hide" and "support HOQrebuild" feilds and legends are not displayed for HD(SCGCQ00695070)
- In Windows and Linux only controller grouping is working but not sorting(SCGCQ00752000)
- Boot Volume details is shown in Megacli but not with storcli.(SCGCQ00759187)
- ASO count mismatch in show ASO w.r.t ASO in storcli show all cmd(SCGCQ00779806)
- Reviewing the Code AdataMfi, RmDataMf and VdDataMf files.(SCGCQ00785918)
- Missing the Display of the property temperatureCtrl.(SCGCQ00792264)
- When Supercap SOH is reported bad, CLI still see the Supercap status as "Optimal"(SCGCQ00794760)
- Explicit null dereferenced in vddatamf.cpp (getVdDetldInfo)(SCGCQ00795336)
- fisResBuffer memory allocation is not considering the failure case(SCGCQ00796206)
- Memory not freed which can cause leak(SCGCQ00804554)
- Varailble need to be freed before returning in all failure case(SCGCQ00804650)
- IDA show incorrect RAID controller type information(SCGCQ00806966)
- MR_6.8_Storcli: Cachevault flash size shows differently for different commands in storcli under RHEL6.6 PPC64(SCGCQ00837197)
- Read policy should be 'NORA' for IMR controller instead of 'none'(SCGCQ00840372)
- ASO no mismatch between the commands 'storclif show' and 'storclif /c0 show aso'(SCGCQ01081111)
- MR7.1_NVMe: Post NVMe VD Creation, SAS VD Creation of any Raid Level (Except R0) is not allowed(SCGCQ01127464)
- Ventura: OEMID is shown as LSI in scheduled tasks on querying controller info.(SCGCQ01157723)
- Removing Unused and logically dead code in storcli(SCGCQ01204045)
- Remove all the manufacturing/Factory commands from end customer CLI tool(SCGCQ01206492)
- Unified StorCLI 7.1-Fixing resource leaks in IT controller framework and command processors-Part2(SCGCQ01207685)
- NVMe 7.1:Failure description string is empty in storcli(SCGCQ01234083)
- Second OCR request not getting triggered, fired when first OCR request about to finish, but O/P shows success.(SCGCQ01290216)
- iMR_Inv_6.1:StoreCLI-StoreCLI does not give proper message while trying to create 33rd VD on iMR FURY controller(SCGCQ00364332)
- MR: not able to create PRL11 using 96 drives.(SCGCQ00381100)
- StorCLI-Invader : The "coercion" mode is not in sync with the legacy values.(SCGCQ00383043)
- Raptor Galaxy:No of blocks displayed for a VD remains same for all VD sizes.(SCGCQ00465956)
- StorCLI reports controller status as 'OK' when Arctrus controller(9361-8i) booted in safe mode(SCGCQ00523370)
- MR_Inv_6.3_PPC:Storcli- Storcli gives 'Segmentation fault' while retriving 'advanced software options' on SLES11 SP2 PPC64(SCGCQ00574287)
- MR6.4_StorCLI: c0 show controller health is failing(SCGCQ00627672)
- Add adapterOperation support details in /c0 show all for Emulationtype.(SCGCQ00759181)
- OEMID is coming as "Unknown" for /c0 show all(SCGCQ00759862)
- CPLD(SCGCQ00787705)
- CPLD UPDATE : cpld upgradableCPLD support bit need to add under hardware configuration(SCGCQ00792233)
- rlListPtr is not handled properly in failure case(SCGCQ00796227)
- Segmentation fault while querying for GHSP/DHSP while drive is going in shield-HSP state.(SCGCQ00820392)
- LDViewMirror is giving segmentation fault(SCGCQ00830435)
- Storcli shows caching is enabled on Source VD when CCVD is in offline state(SCGCQ00835758)
- Storcli gives wrong error code with respect to FW state while converting JBOD to UG(SCGCQ00839321)
- Checking in compilation error for Libmods(SCGCQ00919973)
- VD Creation fails with "Invalid Arguments" error with latest FW Headers(SCGCQ01001356)
- Coverity Fixes for Unified Storcli 7.1 stream(SCGCQ01204055)
- PH2: Pre Alpha-Ventura B0 storcli command not exited when storcli /c1 show issued.(SCGCQ01205407)
- Fixing resource leaks and logically dead code in cli.(SCGCQ01208101)
- Ventura B0 PH3 StorCLI : Segmentation fault seen with show command on freebsd 10.2 X86 OS(SCGCQ01250553)
- MR 7.2:PPC : StorCLi throws error while loading the saved configuration.(SCGCQ01273381)
- Ventura IT show command displays all the PD's under Drive group-0 which is wrong(SCGCQ01274709)
- StorCLI does not provide command to set HSM or HCOE SCGCQ00358662(SCGCQ00360745)
- StorCLI cannot displays information for controller in Safe mode(SCGCQ00365950)
- StorCLI does not show both "Current Write Policy" and "Default Write Policy" for VD(SCGCQ00408070)
- debug prints are present when issuing /co/eall show(SCGCQ00475815)
- PCLI Sparc(1.07.02):" Cli show all" command fails with error msg "Error! App exec failed in FW PCLIError! Internal".(SCGCQ00518543)
- Verify StorCLI warns on destructive operations(SCGCQ00712982)
- /c0 show all page are having some incorrectness in controller information(SCGCQ00716584)
- MR6.5alpha:Segmentation fault(coredump) observed on executing ./storcli /c1/v63 show all for 64th cachecade VD in ubuntu14.04(SCGCQ00729691)
- Add adapterOperation support details in /c0 show all for cachebypassMode.(SCGCQ00757358)
- supportCPLDUpdate support bit needs to be updated in contoller detailed information(SCGCQ00792200)
- supportDrvActivityLEDSetting supported bit need to be update in Supported adapater Operations(SCGCQ00792211)
- Incorrect sizeof expression in dcmdprm(SCGCQ00793354)
- Non-array delete for objects in rmdatamf(SCGCQ00793361)
- Storcli displays wrong native driver version on ESXi5.5 when quered .(SCGCQ00803420)
- Variable going out of scope without freeing which causes memory leak(SCGCQ00804663)
- Non-array delete for objects: destructors will not be called for objects in the array leading to unexpected behaviour.(SCGCQ00804672)
- FW hangs during SVD and CCVD migration based on DDR Size(SCGCQ00809736)
- Unified CLI:EFI:Ventura IT:Adpcount is zero when the controller is in fault state(SCGCQ01016583)
- Ventura:CLI App stopped working on executing /c0/eall/sall delete hotsparedrive(SCGCQ01081096)
- Reverting back SL_MAX_OS_DRIVE_COUNT value to 300(SCGCQ01114306)
- PD related information missing for NVMe drives(SCGCQ01126564)
- Factory settings command needs to validate the manufacturing data in the INI, and log the license details with proper time(SCGCQ01205365)
- Unified StorCLI 7.1:IT Firmware downgrade should be supported in StorCLIO and not StorCLI(SCGCQ01232854)
- StorCLI(SCGCQ01274554)
- Adapter 0: Failed to start SecureErase on Virtual Drive 0 in VMware_ESXi_5.1(SCGCQ00348911)
- iMr_Fury_StorCLi:SectorSize show as "512KB" for 512Bytes drives(SCGCQ00362070)
- StorcLi_5.7: Remove the description for "Ra=Read Ahead Adaptive" in VD show info.(SCGCQ00396665)
- The bootwithpinnedcache logic is backwards, both storcli and the FW are affected(SCGCQ00436107)
- StorCli: Segmantation fault appearing in storcli when issuing /c0/fall show(SCGCQ00564008)
- CS2.0: Ctrl-R Domain Id is not showing in controller properties(SCGCQ00622605)
- Storcli shows two controllers in the system though you have only one cotntroller in the system.(SCGCQ00690355)
- Remove the code related to enableVCor feild this was used for ASD and now it is not used any more.(SCGCQ00789402)
- supportForceFlash needs to add under suported adapter operations(SCGCQ00792205)
- Operands don't affect result in pddatamf.cpp causing wrong result(SCGCQ00795334)
- Unchecked return value in rmdatamf.cpp (getControllerStatus)(SCGCQ00795342)
- MR_6.7_Storcli: Storcli reports wrong tmm and scap date of manufacture under scap properties in RHEL6.6 PPC64(SCGCQ00801311)
- LibMod changes for CTLR+R (PERC9.2) to read Disk Write Cache settings of PD.(SCGCQ00811117)
- StorCLI 7.0015 cannot create VD using firmware 6166 under Windows 2012(SCGCQ01046368)
- Ventura:StorCLI-EFI-StorCLI hang on Purley @ Intel/Quanta for 3408(SCGCQ01052844)
- SAS3 Invader/Intruder-Storcli : IR card is getting detected in EFI shell(SCGCQ01081353)
- No details of pending FW images when run StorCLI /c0 show all after update to new firmware(SCGCQ01090082)
- Libmod changes for defect(SCGCQ01112455) storcli says failed to exit from storelib IT library while enquiring the controller info(SCGCQ01114437)
- PH2: Pre Alpha-Ventura B0 download completeflash command fails.(SCGCQ01198721)
- Update /sall show legend to show powersave for SSDs in addition to spun down for HDDs(SCGCQ01213236)
- MR7.1 StorCLI misspelling of "Drive Acitivy LED" During Set(SCGCQ01229289)
- Help for Compare linkspeed is not complete(SCGCQ01275454)
- CLI reporting Large VD (56TB) size slightly smaller than other apps (by .001)(SCGCQ00477037)
- Storcli /c0 show ASO fails and delay in displaying .(SCGCQ00493491)
- Storcli reports VD Type as "Rec1" during reconstruction on SPARC.(SCGCQ00499067)
- Command /cx/ex show phyerrorcounters gives bus error in Orcale Enterprise Linux(SCGCQ00799426)
- Libmod changes to support profile management(SCGCQ01048228)
- storcliF 7.23.0.0: VD shown on wrong controller in a system with 2 Talladega 16i controllers installed(SCGCQ01080627)
- Merge of enclosure related changes for phyerror counters from 6.x(SCGCQ01123876)
- Ventura PH3(SCGCQ01253012)
- Compare linkspeed says unsupported when given with multiple Phys(SCGCQ01275455)
- coverity removing out of bounds reads from code(SCGCQ01280460)
- CSET: storelib header file checkin for the latest changes done by storelib(SCGCQ00521999)
- StorCLI :supportDisableImmediateIO adapter properties need to be added under show all command(SCGCQ00792085)
- Firmware error code status MFI_STAT_SECURE_SYSTEM_PD_EXISTS needs to be update in code(SCGCQ00792234)
- Resource leak in VdDataMf scanPartitions(SCGCQ00793363)
- Storcli can't create AHCI LDs(SCGCQ00897637)
- Unified StorCLI:EFI:Masking the SL_GET_CTRL_INFO command when the adapter is in invalid/bad state.(SCGCQ00936676)
- The structure name is changed from oob_i2c to oob to avoid compilation failure in OOB SL(SCGCQ01015024)
- NVMe PD firmware flash failing (not working) as per controller logs, StorCLI show success message(SCGCQ01218214)
- Detailed help missing for IT erase commands(SCGCQ01275474)
- start and stop locate from storcli on IT card with multiple drive option is not working.(SCGCQ01275671)
- Coverity: Adding checks for unchecked return values of function calls(SCGCQ01280453)
Enhancement
- MPI2: Add TargetModeAbort by initiator device handle(SCGCQ00337167)
- New fault code for routine synchronous reset(SCGCQ01264142)
- MPI2: Allow UEFI and BIOS to be Enabled/Disabled individually(SCGCQ00574358)
- MPI2: Security Freeze Lock support during SATA Init (IO Unit Page 1 Flag)(SCGCQ00414050)
- MPI2: Add STATUS QUALIFIER to SCSI IO Error Reply(SCGCQ00396414)
- MPI2: Add OEM Identifier to BIOS Page 1(SCGCQ00357228)
- MPI2: Use Slot Information during Port Enable Event Replay option(SCGCQ00356796)
- MPI2: Add new TargetModeAbort AbortType to only abort Command IUs(SCGCQ00345215)
- MPI v2.6: Additional request and reply descriptor formats(SCGCQ00259613)
- API changes for CR55(SCGCQ01222700)
- API change for Simplified RAID10 Creation(SCGCQ01222698)
- API Changes Required for Specific OEM Backplane functionality(SCGCQ01218406)
- API changes for PR SCGCQ01139678(SCGCQ01215334)
- MPI 2.5 : Add support for reporting Chassis Slot to Enclosure Page 0(SCGCQ01213028)
- MPI 2.5: Add two new reason codes to Active Cable Exception Event Data(SCGCQ01208954)
- API changes for PR SCGCQ01127742(SCGCQ01203751)
- MPI 2.5 and 2.6: Need IT FW to send new event for expander failing SMP(SCGCQ01180886)
- MR 6.12(SCGCQ01146597)
- MR 7.0: Add supportPdMapTargetId flag in MR_CTRL_INFO and MFI_CAPABILITIES(SCGCQ01141251)
- MR 6.13: Add API support for TFM/SCAP _MR_BBU_VPD_INFO_FIXED parameters(SCGCQ01139344)
- MR 6.13: Add a new control command to fetch ROC temperature data over I2C(SCGCQ01137627)
- MR 7.2: Add API support to make application work with Cachecade3.0 on Ventura (Public)(SCGCQ01114969)
- MPI 2.5: Add new connector types(SCGCQ01085073)
- MPI 2.5: Modify "SAS IO Unit Page 4" to add a new field "SATAHintingTimeout"(SCGCQ00996127)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply(SCGCQ00988360)
- MPI 2.5: Update Description of BiosOptions field in BIOS CONFIG PAGE 1(SCGCQ00853162)
- MPI 2.5: BIOS Page 1 BiosOptions Advanced Adapter Configuration Enable(SCGCQ00791885)
- MPI 2.5: add WWID to BIOS Page 3(SCGCQ00785208)
- MPI 2.5: update copyright info(SCGCQ00728066)
- MPI 2.5: BIOS Page 1 additions(SCGCQ00700829)
- MPI 2.5: distribute Target Command Buffers Received across multiple reply queues(SCGCQ00685820)
- MPI 2.0: Add product-specific Flag bit to Clean Tool(SCGCQ00569175)
- Add type BIOS for HashImageType.(SCGCQ00566306)
- Identify physical location of a target device(SCGCQ00523879)
- MPI 2.5: add reserved fields to IO Unit Page 7 for future use(SCGCQ00477817)
- MPI 2.5: obsolete "Limit SATA max rate to 1.5 Gbps"(SCGCQ00471293)
- MPI 2.5: IOCInit multiple Reply Descriptor Post Queue addresses(SCGCQ00466819)
- MPI 2.5: obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL(SCGCQ00438437)
- Allow Protection Information bit for IR Volume Create(SCGCQ00385306)
- MPI 2.6: add host page size to IOCInit Request and IOCFacts Reply(SCGCQ00357551)
- MPI 2.6: add PCIe Device Config Pages(SCGCQ00345271)
- MPI 2.6: PCIe Switch Config Pages(SCGCQ00345270)
- MPI 2.6: PCIe Topology Change List Event(SCGCQ00345266)
- MPI 2.6: add PCIe Event Data (Generic), PCIe Device Status Change Event, and PCIe Enumeration Event(SCGCQ00345260)
- MPI 2.5: additional requirements for some IOCs that support more than 8 MSI-x vectors(SCGCQ00338506)
- MPI 2.6: PCIe IO Unit Page 0 & 1 definitions(SCGCQ00336383)
- MPI 2.5: obsolete the Clear SATA Affiliation bit in SAS IO Unit Page 1(SCGCQ00310439)
- MPI 2.6: update SGL chapter to include PCIe(SCGCQ00294131)
- MPI 2.6: add Escape Passthrough bit to IO Flags of SCSI IO Request & Target Assist Request(SCGCQ00294055)
- MPI 2.6: NVMe Encapsulated request(SCGCQ00264759)
- MPI 2.6: SOP Encapsulated request(SCGCQ00264755)
- Added the new Component version for SBR in both Controller-info case and also in Pending FW images use case.(SCGCQ01093183)
- Libmods changes for EFI support for Unified storcli(SCGCQ00923719)
- Add set "Fail PD on SMARTer" property feature to StorCLI(SCGCQ00818101)
- OEL Support for SPARC(SCGCQ00787923)
- Added the library functions for the new MR API bits and LD operations.(SCGCQ00685010)
- Added the library functions for the new MR API bits and LD operations.(SCGCQ00685007)
- Display the NCQ enabled/disabled status of every SATA disk drive in the output of StorCLI and MegaCLI(SCGCQ00564477)
- CSET: (Tbolt PR 211180) Punctured Block Logging Improvements(SCGCQ00342399)
- MPI 2.6 Add Atomic Request Descriptor capability(SCGCQ00227735)
- MPI 2.6: add IO Unit Control Request(SCGCQ00345258)
- MPI 2.6: PCIe Link Config Pages(SCGCQ00345272)
- MPI 2.6: Enclosure Management(SCGCQ00345273)
- Device Info field for PCIe devices(SCGCQ00353339)
- MPI 2.6: add Port Request bit to IoFlags field of SCSI IO Request(SCGCQ00360843)
- MPI 2.6: new family values for ProductID fields(SCGCQ00360952)
- MPI 2.6: move all SAS IO Unit Page 4 functionality to IO Unit Page 11(SCGCQ00363600)
- Modified address space bits(SCGCQ00397136)
- MPI 2.6: Add PCIe IO Unit Page 4(SCGCQ00397563)
- MPI 2.6: PCIe Device Page 2 reporting MDTS for NVMe devs(SCGCQ00397568)
- MPI 2.6: Add board power fields to IO Unit Page 7(SCGCQ00397572)
- MPI 2.6: Add support for SAS Persistent Connections(SCGCQ00397577)
- MPI 2.6: Add NVMe SGL support(SCGCQ00398256)
- MPI 2.6: Add NVMe SGL support to IEEE SGL(SCGCQ00432541)
- MPI 2.6: System Interface Register Set update(SCGCQ00464402)
- Remove _SATA_TRANSMIT_PORT_SELECT_SIGNAL in IO Unit Control Request(SCGCQ00480292)
- MPI 2.6: shutdown operation for IO Unit Control Request(SCGCQ00496998)
- MPI 2.6: Add supported link rates and widths for PCIe devices(SCGCQ00564281)
- MPI 2.6: Add additional NVMe AccessStatus codes(SCGCQ00574070)
- MPI 2.6: Add BootFlags field to Firmware Image Header(SCGCQ00601869)
- MPI 2.6: Add new FLASH region types(SCGCQ00619371)
- MPI 2.6: Added an additional signature value for the firmware image header(SCGCQ00623271)
- MPI 2.6: additional AccessStatus values for PCIe Device Page 0(SCGCQ00664957)
- MPI v2.6: Added Intruder / Cutlass device IDs for manufacturing pages(SCGCQ00680527)
- MPI 2.6: Extend Task Management(SCGCQ00686666)
- MPI 2.6: Add device off flag to SCSI Enclosure Processor messages(SCGCQ00776177)
- MPI 2.6: New Phy event codes added to Ventura(SCGCQ00789600)
- MPI 2.6: Add capability to send FPDMA/NCQ commands via SATA Passthrough(SCGCQ00813389)
- MPI 2.6: BootDeviceSelect and Host Boot changes for Ventura(SCGCQ00827088)
- MPI 2.6: add PCI Device ID's(SCGCQ00828497)
- MPI 2.6: methods to report Active Cable power problems(SCGCQ00831588)
- MPI 2.6: SRIOV support for PCIe devices(SCGCQ00852827)
- MPI 2.6: Update Flash Signature.(SCGCQ00852831)
- profile management API(SCGCQ00867953)
- MPI 2.6: add new feature to control NVMe SGL format(SCGCQ00872169)
- Mega API modifications needed for RMW-FP and Cache bypass features in Ventura(SCGCQ00875328)
- Merging api_overrides mega_api files with the files in the Mega_API development stream(SCGCQ00883262)
- MPI 2.6: Additional PCIe Enumeration Event EnumerationStatus bit(SCGCQ00884740)
- MPI 2.6: Update Ventura family device ids to match latest EDS(SCGCQ00915256)
- MPI 2.6: update Marlin-class device IDs(SCGCQ00915336)
- MPI 2.6: PCIe IO Unit Page 0 and 1 tweaks(SCGCQ00922213)
- MPI 2.6: Remove all SOP references(SCGCQ00925839)
- Change library name to SLIT(SCGCQ00933175)
- Ventura: de-feature AHCI(SCGCQ00941620)
- MPI 2.6: Remove all AHCI references(SCGCQ00948258)
- MPI 2.6: Add support for SAS-4 and PCIe-4(SCGCQ00948955)
- MPI 2.6: Add Enclosure Level and Connector name to PCIe device page 0(SCGCQ00949638)
- MPI 2.6: add LinkNum field to the PCIe Link configuration pages(SCGCQ00954619)
- MPI-2.6: backend PCIe feature initialization status reporting(SCGCQ01009104)
- MPI 2.6: add flag to force completion queue entry return for NVMe Encapsulated request(SCGCQ01013930)
- MPI2.6: Fix defines that are not unique within the first 32 characters(SCGCQ01015826)
- MPI 2.6: direct reporting of negotiated PCIe link width and speed(SCGCQ01017027)
- MPI 2.6: Backend SRIS mode enable flag(SCGCQ01018687)
- MPI2.6: Reserve ExtPageTypes for Dragon(SCGCQ01020473)
- MR_CTRL_INFO expansion from 2K to 4K(SCGCQ01023741)
- mega api changes for ibuttonless PR(SCGCQ01059740)
- MPI2.6: Add x16 PCI support for Marlin family products(SCGCQ01063009)
- MPI2.6: Fix PCI device page enclosure level/connector name to match SAS device page(SCGCQ01071374)
- Profile Management Changes to support requestedProfileID and optimisedProfile(SCGCQ01075821)
- MPI 2.6: Modify "SAS IO Unit Page 11" to add a new field "SATAHintingTimeout"(SCGCQ01092340)
- MEGA_API Changes to incorporate new IO subtype to support redirect cached IO(SCGCQ01094549)
- MPI 2.6: Add Sea Arch class and Product IDs(SCGCQ01116837)
- MR 7.0: Add MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT = 7 to mfi.h file(SCGCQ01133839)
- MPI2.6: Added new image type and flash region definitions(SCGCQ01136127)
- MPI 2.6: Add new clean tool options(SCGCQ01141732)
- MPI 2.6: Add two new reason codes to Active Cable Exception Event Data(SCGCQ01146583)
- Define CurrentFwNvmePageSize element in new MFI_REG_STATE_EXT3 register(SCGCQ01188725)
- MR7.1. Add MR API bit to indicate the profile is NVMe Only profile(SCGCQ01213092)
- MPI2.6: Mfg7 support for arbitrary starting slot number(SCGCQ01213267)
- MPI 2.6: Add new firmware download type (CBB BACKUP)(SCGCQ01258005)
- MPI 2.5: Add additional EEDP Error Reporting capability to SCSI IO Reply(SCGCQ01002367)
- MPI 2.5: Signed images for FWDownload(SCGCQ00469990)
- MPI 2.5: Toolbox Console Text Display Tool(SCGCQ00415512)
- Display the Storelib version in the show command.(SCGCQ01286063)
- Unified StorCLI 7.1: PCIe Lane Speed and Link Configuration changes(SCGCQ01226457)
- Unified StorCLI 7.1:OEL-Sparc support to Unified StorCLI(SCGCQ01196496)
- Add support to allow Device names greater than 107(SCGCQ01039328)
- Ventura : Add MR_ARRAY_EXT Support to StorCLI(SCGCQ01024636)
- Enable SED on JBOD(SCGCQ00755527)
- Allow VMWARE version of STORCLI cannot be run from any directory(SCGCQ00642230)
- Added the OEM-NEC check for getting default disk-cache policy in Libmods as Disable.(SCGCQ00632051)
- Request RAID CLI to display the Patrol Read Start Time(SCGCQ00564474)
- Implemented the diag results to print on console(SCGCQ00525321)
- MWCLI. R10, R50, R60, R00 VD creation(SCGCQ00369742)
- MWCLI. Add HA support into storcli(SCGCQ00352120)
- Create Spanned R0 array (00) in StorCLI(SCGCQ00350668)
- Unified StorCLI 7.2:ARM-Linux support to Unified StorCLI(SCGCQ01241607)
- Add NVMe device related changes(SCGCQ01034678)
- Implemented the VD-VF mapping related commands in factory tool(SCGCQ00827665)
- Complete 240VD support for utilities(SCGCQ00693042)
- STORCLI will support MR controller management without UEFI BootServiceDriver Driver and also has retain functionality of existing seeadapter-through-driver functionality.(SCGCQ00621287)
- dcmd path chagnes for supporting the new cachevault api(SCGCQ00381311)
- Controller should not be reset after firmware download in CLI for SAS 3.5 Controllers(SCGCQ01399793)
- Unified StorCLI 7.1:PPC Support(Big endian and Little endian) to Unified StorCLI(SCGCQ01196715)
- Added the serial to properly log to the USB when the license is used for manufacturing the MFC on a controller.(SCGCQ01175821)
- Unified CLI:Addition of appropriate device id's for Ventura(SCGCQ01132146)
- LibMods: Increase maximum cache size for Cachecade to 2048GB. This will be named CC 2.5(SCGCQ00829204)
- UDK Support for EFI(SCGCQ00795150)
- Implemented the storcli command to print SATA drive's phy error counters and reset them.(SCGCQ00735171)
- Consistent Sorting of Controllers for End Users in Customer Facing Tools(SCGCQ00696872)
- Provide a way to enable or disable 512E using Applications(SCGCQ00351234)
- Refer attached design doc(SCGCQ00349599)
- Unified StorCLI : [Lenovo Purley] Adding tape drive support to Unified StorCLI for IT Ventura controllers.(SCGCQ01351495)
- Unified StorCLI LibMods 7.1: Libmod changes for PCIe Lane Speed and Link Configuration(SCGCQ01227050)
- Unified CLI changes to support host boot in MR with faulty FW(SCGCQ01093217)
- Unified StorCLI:Implementing StoreLib IT static framework with StorCli(SCGCQ00916344)
- LD Deletion stalling all IOs on Niwot HBA 12.12.0-0178(SCGCQ00757473)
- RRB 71(SCGCQ00750164)
- If any error that is returned as negative we return it s 0xFF from CLI to shell else FW returned error status will be returned to shell.(SCGCQ00665081)
- SED/FDE changes for storcli Synchro(SCGCQ00632240)
- ASD- StorCLI(SCGCQ00467863)
- Implemented 128 drive support by using the new ENCL_INFO structures(SCGCQ00333209)
- PERC 10 WIndows Support(SCGCQ01213160)
- PERC 10 WIndows Support(SCGCQ01213157)
- LibMods-Porting of MR6.x changes to Ventura(SCGCQ01109080)
- Megacli/storcli support for lmrc driver(SCGCQ00433703)
- PR SCGCQ00319011: Rebuild time reset(SCGCQ00381093)
- Uneven span support is added in StorCLI.(SCGCQ00349548)
- Unified StorCLI 7.1-Phase 2:IT Firmware downgrade support to Unified StorCLI(SCGCQ01224391)
- Add EFI support for the manufacturing command to program.(SCGCQ01191095)
- Ventura : Add IT Support to StorCLI [Checking in LIBMODS Changes ](SCGCQ00859216)
- Storcli Should display SAS Address N/A if its invalid and change Host interface type names from PCIX, PCIE to PCI-X, PCI-E(SCGCQ00828476)
- Monitoring Drive performance and predictive failure(SCGCQ00817977)
- While saving and Restoring the configuration on controller we used to save MR_CONFIG_DATA and MR_CTRL_PROP. Added the below(SCGCQ01234118)
- Unified StorCLI 7.1:FreeBSD OS support to Unified StorCLI 7.1(SCGCQ01191237)
- LimMod changes related to CtrlH & MSM Mismatch on write-back options(SCGCQ00818987)
- Functionality to extract field value from new API changes(SCGCQ00794841)
- MR 4.12: Big endian architecture support for MR Linux driver and StorCli(SCGCQ00558815)
0007.0057.0000.0000 - Moderate Impact/Low Probability of Occurrence
-------------------
Enhancement:
- Added support for ThinkSystem HBA and RAID.
1.20.20 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed an issue where command "/cx show alilog d:/logfile=xyz.txt" reports success even when destination doesn't have enough space to save log file - (SCGCQ00861227)
- Fixed an issue where command "/c0/pall show" does not show Port number and whether the Port is valid - (SCGCQ00865335)
- Fixed an issue where command "/c0/epd0,1 show" doesn't report epd1 as invalid - (SCGCQ00908866)
- Fixed an issue where command "/c0 show bootdrive" doesn't display EPD for EPDs - (SCGCQ00918811)
- Fixed an issue where command "/c0/fall show" succeeds but "/c0/fall show all" fails- (SCGCQ0043074)
- Fixed an issue where command "/c1/e83 show status" may show "Unsupported" in many fields - (SCGCQ00950438)
- Fixed an issue where command "storcli /c0/d1 set transport=on sdhsp=on" uses a dedicated hotspare even though the command requests a shared hotspare - (SCGCQ00981663)
- Fixed an issue where an incorrect message may occur when creating a RAID5 - (SCGCQ00995140)
- Fixed an issue where command "/c0/cv start retentiontest" may result in an extra "File Write ERROR !!!" print - (SCGCQ00997401)
- Fixed an issue where an incorrect failure message may occur when creating a RAID1 with 3 drives - (SCGCQ00999258)
- Fixed an issue where Virtual Drive policy isn't retained after firmware flash fails - (SCGCQ01000358)
- Fixed an issue where storcli does not display description on command success - (SCGCQ01023973)
- Fixed an issue where "force" argument may not work with "parallel" argument - (SCGCQ01026081)
- Fixed an issue where command "/c0 show autoconfig" may result in empty values - (SCGCQ01026945)
- Fixed an issue where unable to set multipath parameter when firmware returns "MFI_STAT_OK_REBOOT_REQUIRED" - (SCGCQ01029534)
- Fixed an issue where command "/c0/eall/sall download src=H7280A520.P551 parallel" may report failure and success, when the flash has failed - (SCGCQ01030430)
- Fixed an issue where Mode 5 firmware download is not working with "parallel" argument - (SCGCQ01030535)
- Fixed an issue where storcli reports "Succeeded" instead of "Initiated" during a PD firmware flash status check - (SCGCQ01031218)
- Fixed an issue where storcli shows an incorrect error message when trying to remove the Blocked Access from SVDs - (SCGCQ01039102)
- Fixed an issue where storcli only shows firmware flash status for the last drive when multiple drives are being flashed simultaneously - (SCGCQ01039484)
- Fixed an issue where storcli does not give context-specific output for storcli help commands - (SCGCQ01039534)
- Fixed an issue where command "/c0 h" does not work - (SCGCQ01039745)
- Fixed an issue where command "/c0/cv start learn" may result in an incorrect message if the learn cycle fails - (SCGCQ01039757)
- Fixed an issue where Mode F is not fired after Mode E when "activatenow" is specified with no delay - (SCGCQ01052895)
- Fixed an issue where storcli did not disable offline commands and exit when Mode E or Mode F firmware download fails - (SCGCQ01053068)
- Fixed an issue where the entire error message is not shown when trying to update the security key "rekeyLock" - (SCGCQ01059105)
- Fixed an issue where JBOD status is shown under EPD column when displaying the status message - (SCGCQ01062314)
- Fixed an issue where "Segmentation fault" error may occur when creating and deleting multiple VDs in a loop - (SCGCQ01062646)
- Fixed an issue where an saving logs to an invalid destination does not cause an error - (SCGCQ01063899)
- Fixed an issue where JBOD information is displayed in EPD mode - (SCGCQ01064101)
- Fixed an issue where MFC_DEFAULTS are not handled correctly during VD creation - (SCGCQ01070120)
- Fixed an issue where "Failed operation not possible for current RAID level" error may occur when the error should have been "resources already in use" - (SCGCQ01073669)
- Fixed an issue where multi init parameter help syntax was missing - (SCGCQ01078997)
- Fixed an issue where storcli might crash when more than 200 characters are in the command - (SCGCQ01081082)
- Fixed an issue where extra prints and incorrect messages may occur while flashing PD firmware on SAS and SATA drives at the same time - (SCGCQ01091011)
- Fixed an issue where help did not include VFQDMode values and their explanations - (SCGCQ01128071)
- Fixed an issue where command "/c0/vall set pi=off" can error even though the command was successful - (SCGCQ01133117)
- Fixed an issue where output of show init/erase operation lists as VD instead of EPD - (SCGCQ00935416)
- Fixed an issue where multiple entries of the same object in a single command still results in success - (SCGCQ00947387)
- Fixed an issue where virtual drive may disappear after starting an erase on a RAID0 VD in simple and normal mode - (SCGCQ00995154)
- Fixed an issue where command "/c0/vall set hidden=on" or "/c0/vall set hidden=off" may error even on success - (SCGCQ01026907)
- Fixed an issue where "behavior" may appear as "behaviour" - (SCGCQ01029447)
- Fixed an issue where command "/c0 show events" errors even when successful - (SCGCQ01030139)
- Fixed an issue where storcli may ask for a system reboot if changing behavior from EPD to RAID0 - (SCGCQ01035493)
- Fixed an issue where storcli may not display "behavior mode" after setting the behavior mode - (SCGCQ01035500)
- Fixed an issue where command "/cx show preservedcache" may result in a "Segmentation fault" error when pinned cache is present - (SCGCQ01036028)
- Fixed an issue where command "/c0 show phyerrorcounters" shows success without printing the table - (SCGCQ01038669)
- Fixed an issue where MRI mode is taking any value and not reflecting - (SCGCQ01039536)
- Fixed an issue where command "/cx show alilog" calculates Leap Year incorrectly - (SCGCQ01039554)
- Fixed an issue where command "/c0/fall del" may not show correct error message when controller has pinned cache and is in Safe Mode - (SCGCQ01043063)
- Fixed an issue where controller reset command was not blocked in EFI environment - (SCGCQ01052322)
- Fixed an issue where the copyright date showed 2015 instead of 2016 - (SCGCQ01053608)
- Fixed an issue where command "storcli /c0 /v0 start erase simple patterna=1" is not setting the pattern - (SCGCQ01057994)
- Fixed an issue where "/c0 set pcilinkspeed=3" command reports success even when the command isn't sent to firmware - (SCGCQ01058298)
- Fixed an issue where MFG data shows success when inputting an invalid file - (SCGCQ01058300)
- Fixed an issue where JBOD is being displayed when querying EPD information - (SCGCQ01059088)
- Fixed an issue where error "Snapshot is enabled on the Virtual Disk" may occur when creating and deleting multiple VDs in a loop - (SCGCQ01060805)
- Fixed an issue where "show BBMT" may show information for EPDs - (SCGCQ01064035)
- Fixed an issue where error "Invalid RAID level" may be shown instead of "Cannot create raid level with 1 span" - (SCGCQ01064084)
- Fixed an issue where SATA SSD firmware cannot be flashed - (SCGCQ01085706)
- Fixed an issue where storcli does not handle the return status properly during controller firmware flash - (SCGCQ01132613)
- Fixed an issue where command "storcli /c0/v1 start migrate type=raid1 option=add drives=120:5,7" may fail - (SCGCQ00879775)
- Fixed an issue where EPD-specific operations may not work - (SCGCQ00892973)
- Fixed an issue where delete EPD command may show Delete VD success message instead of Delete EPD success - (SCGCQ00905830)
- Fixed an issue where reboot required message may not occur when toggling SRIOV - (SCGCQ00919940)
- Fixed an issue where pinned cache of EPD may generates a listing as a Virtual Drive in the preserved cache message - (SCGCQ00988786)
- Fixed an issue where storcli may fail to set JBOD=off when there are no JBODs - (SCGCQ00993464)
- Fixed an issue where force flash may not work with resetnow opton - (SCGCQ00993466)
- Fixed an issue where storcli command for bbu may not read the SuperCap VPD information properly - (SCGCQ00994876)
- Fixed an issue where storcli may error "Resource already in use" when trying to configure RAID0 with online PDs - (SCGCQ01003415)
- Fixed an issue where storcli may not be able to change the behavior mode - (SCGCQ01023985)
- Fixed a typo in remaining time when issuing command "/cx/bbu show" - (SCGCQ01024968)
- Fixed an issue where printf may be seen in libmods in power-on-hours command - (SCGCQ01033027)
- Fixed an issue where storcli may not show an error when deleting security key fails - (SCGCQ01039756)
- Fixed an issue where "/c0/dall set" command may report success even though the command is incomplete - (SCGCQ01052306)
- Fixed an issue where command "/c0 dall show" may hang or throw an exception - (SCGCQ01052841)
- Fixed an issue where command "/c0 show" may display JBOD list when the behavior is set to EPD - (SCGCQ01052876)
- Fixed an issue where command "/c0 show memscribpatterns" status may report success but description says failed - (SCGCQ01058525)
- Fixed an issue where a "Synchronous Exception" may occur when running command "/c0 set vpd" with an incorrect input file - (SCGCQ01059798)
- Fixed an issue where storcli may throw an inappropriate error when trying to flash the wrong drive firmware to a drive - (SCGCQ01065620)
- Fixed an issue where drive firmware flash with parallel option may return error code 18 - (SCGCQ01066204)
- Fixed an issue where storcli may display Nytrocache even when controller does not support it - (SCGCQ01067274)
- Fixed an issue where storcli set JBOD as boot drive and removing JBOD as boot drive may display different messages - (SCGCQ01079667)
- Fixed an issue where connector name may not be sorted properly - (SCGCQ00890604)
- Fixed an issue where command "/c0/epd20 del" may not throw error when EPD is not present - (SCGCQ00904055)
- Fixed an issue where stop erase help file may show incorrect syntax - (SCGCQ00910533)
- Fixed an issue where host name and operating system details may show client machine instead of host machine - (SCGCQ00910614)
- Fixed an issue where storcli may misspell "controller" when flushing controller - (SCGCQ00973474)
- Fixed an issue where setting Consistency Check mode may fail if no start time given, and may set successfully if wrong time is given - (SCGCQ01039758)
- Fixed an issue where some commands may not report success on success - (SCGCQ01050695)
- Fixed an issue where storcli may show the wrong message when boot drive is cleared on all drives - (SCGCQ01053241)
- Fixed an issue where "/c0/vall show all" has an inaccurate description - (SCGCQ01058116)
- Fixed an issue where an extra space may appear in the message "Flash image is not supported , Try force." - (SCGCQ01064773)
- Fixed an issue where a SAS Address mismatch may occur after setting SAS Address from storclio - (SCGCQ01082500)
- Fixed an issue where storcli may show SDS reference and multiple modes for personality switch - (SCGCQ01127378)
- Fixed an issue where help output is not available for "/c0 add jbod h" - (SCGCQ01131493)
- Fixed an issue where command "/c0/epd4 del discardcache" may throw a syntax error - (SCGCQ00904205)
- Fixed an issue where error "Add EPD failed" may occur when creating an EPD - (SCGCQ00908864)
- Fixed an issue where Auto Config option MRIE-Mode may not be SMARTMODE - (SCGCQ00922540)
- Fixed an issue where EPD may not be allowed in JBOD mode - (SCGCQ01050766)
- Fixed an issue where the table may show EPD instead of JBOD - (SCGCQ01058178)
- Fixed an issue where error " segmentation fault " may occur - (SCGCQ01063305)
- Fixed an issue where command "set cc" may fail even though cc was set successfully - (SCGCQ01074482)
- Fixed an issue where installation of storclio may fail with syntax error - (SCGCQ01074514)
- Fixed an issue where a personality switch from JBOD to EPD may not clear JBOD and EPD config - (SCGCQ01080493)
- Fixed an issue where "delete preservedcache" option may not be listed in the help menu "/c0/vx delete h" - (SCGCQ00924642)
- Fixed an issue where storcli may crash when trying to attach a CacheCade Virtual Drive to source Virtual Drive. (SCGCQ00934528)
- Fixed an issue where there may be no error message for failure to initialize EPD - (SCGCQ00935477)
- Fixed an issue where installaton of storclio may fail - (SCGCQ00952422)
- Fixed an issue where references of epdpassthru were not JBOD - (SCGCQ01023981)
- Fixed an issue where command "/c0/vall show bbmt" may not display the corrected and uncorrected values - (SCGCQ01059790)
- Fixed an issue where command "/c0/vall set ssdcaching=on/off" may not apply to all the Virtual Drives - (SCGCQ01060315)
- Fixed an issue where command "/c0/delete config" output may not be consistent - (SCGCQ01091178)
- Fixed an issue where description of "add epd" may not state success or failure - (SCGCQ00908865)
- Fixed an issue where EPD details may not show in "show all" command - (SCGCQ00921937)
- Fixed an issue where BIOS mode may not be able to be changed by storcli - (SCGCQ01058624)
- Fixed an issue where setting lowlatency to OFF, the multipath setting is changed to OFF as well - (SCGCQ01080489)
- Fixed an issue where storcli may crash when issuing command "/c0/vall show" - (SCGCQ00888330)
- Fixed an issue where drive microcode update to directly attached drives may fail in default mode - (SCGCQ00888837)
- Fixed an issue where command "/c0/vall del" may delete EPDs as well - (SCGCQ00915484)
- Fixed an issue where SRIOV may not be enabled by storcli - (SCGCQ00915697)
- Fixed an issue where storcli may continue to prompt even when force option is used for controller firmware flash - (SCGCQ01060461)
- Fixed an issue where connector name for first 8 PHYs of enclosure may not be displayed as expected - (SCGCQ00953464, Port of SCGCQ00890597)
- Fixed an issue where description status in failure message of EPD delete may not be accurate - (SCGCQ01015016, Port of SCGCQ00988760)
- Fixed an issue where factory defaults may not be aligned with the new API - (SCGCQ01044939, Port of SCGCQ01044891)
- Fixed an issue where phyerrorcounters command may not display any PHY Error Counter values - (SCGCQ01049064, Port of SCGCQ01028993)
- Fixed an issue where "show" command may fail - (SCGCQ01004630, SCGCQ01006038, Port of SCGCQ01004617)
- Fixed an issue where command "/call show logfile=filename" may result in error "segmentaton fault" - (SCGCQ01020010, Port of SCGCQ01019547)
- Fixed an issue where command "/c0 show dequeuelog file=filename.txt" may result in error "Segmentation fault(Core Dump)" - (SCGCQ01061120, Port of SCGCQ01014212)
- Fixed an issue where transport command may include "all" when only "shared" is requested - (SCGCQ01093159, Port of SCGCQ01093145)
- Fixed an issue where command "/c0 show alilog" may result in error "Segmentation fault(Core Dump)" - (SCGCQ01015017, Port of SCGCQ01014101)
- Fixed an issue where the hide and unhide options may not be available for a disk group - (SCGCQ01050234, Port of SCGCQ01050181)
- Fixed an issue where storcli may not generate a log - (SCGCQ00998150, Port of SCGCQ00945177)
- Fixed an issue where Global Hotspares may show as TR in disk group query - (SCGCQ01047957, Port of SCGCQ01047789)
- Fixed an issue where command "/bbu show all" may show "Remaining Time Alarm = Yes" even when not applicable - (SCGCQ01143941, Port of SCGCQ01026187)
- Fixed an issue where maintainer name may not be populated when querying storcli version information from operating system - (SCGCQ00912697, Port of SCGCQ00838307)
- Fixed an issue where an invalid error message "Device is expander; use /c0/xp download" may be displayed on expander firmware download - (SCGCQ01110108, Port of SCGCQ00934755)
- Fixed an issue where Virtual Drive number is not sorted in "/c0/vall show vfmap" command output - (SCGCQ00932799, Port of SCGCQ00929211)
- Fixed an issue where storcli may fail to correctly populate log files - (SCGCQ01079016, Port of SCGCQ01074584)
Enhancements:
- Added the personality change command was not present - (SCGCQ00850610)
- Extended the VFMaping to the max VFs suported by the adapter dynamically - (SCGCQ00868220)
- Added multipath support in EPD configuration options - (SCGCQ01015758)
- Added additional CPU support on EFI platform - (SCGCQ01026250)
- Added command to display progress of Patrol Read on a Physical Drive - (SCGCQ01040304)
- Added personality change features - (SCGCQ01111930)
- Added VF-queue depth mode settings - (SCGCQ00907072)
- Added ability to enable firmwre debug via storcli without UART - (SCGCQ00908320)
- Added Secure Erase support to JBOD and System drives - (SCGCQ00929757)
- Added a JBOD entity for various operations - (SCGCQ01047229)
- Added EPD support of setting EPD configuration parameter options - (SCGCQ00907064)
- Added more specific error messages in some circumstances - (SCGCQ00920034)
- Added new compilation environment and makefiles - (SCGCQ00920058)
- Added EPD and EPD-passthrough and single-drive RAID0 modes to eSDS - (SCGCQ01015739)
- Added support for drive microcode update Modes E and F - (SCGCQ01047223)
- Added code to display JBOD personality - (SCGCQ01146775)
- Updated existing implementaton to disable thermal polling in some circumstances - (SCGCQ01154338)
- Added new erase type called Crypto - (SCGCQ01050618)
- Added new command to set the multiInit EPD parameter - (SCGCQ01080273)
- Added support for drive microcode update through parallel loading - (SCGCQ01024964)
- Added support for EPD creation - (SCGCQ00887664)
- Modified a failure message to "This command only applies to Nytro Megaraid controllers. All others will display a failure status." - (SCGCQ01004610, Port of SCGCQ00881414)
1.18.11 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed issue where FW could be downleveled without using the noverchk flag (SCGCQ00924705)
- Fixed inaccurate message displayed while deleting a Cachecade Virtual Drive (CCVD) (SCGCQ00897785)
- Fixed issue where physical disk (PD) FW upgrade would fail with some SATA drives (SCGCQ00873612)
- Fixed issue where StorCLI failed to dump lastoneday pdfailevents in a file (SCGCQ00853196)
- Fixed issue where StorCLI was not reporting command success for a StorCLI64 /c0 show events file=eventLog.txt command (SCGCQ00851339)
- Fixed issue where StorCLI would not find enclosures in multipath environment (SCGCQ00873620)
Enhancements:
- Updated the BBU-properties in /c0/bbu show all (BBU learn mode) (SCGCQ00904662)
- Added the support to set and clear the transport on a DG (SCGCQ00920046)
- Added the support to change the large queue depth ctrl property in StorCLI (SCGCQ00933318)
- Implemented commands to save/restore the configuration on the controller. (SCGCQ00851795)
- Add support to detect that an OS is installed on a JBOD and to block it from being changed to Unconfigured Good (SCGCQ00828030)
- Provide a more descriptive port enumeration (SCGCQ00854620)
- Add support to enable/Disable of Large IO Support (SCGCQ00894644)
1.16.14 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed an issue where no error message would occur when attempting to create a VD with Write-Back policy on a controller that does not support Write-Back - (SCGCQ00885617)
- Fixed an issue where StorCli would report "not in progress" for a rebuild instead of "paused" - (SCGCQ00907176)
- Fixed an issue where Foreign VD count of a spanned drive group is reported twice - (SCGCQ00911715)
- Fixed an issue where an invalid error "Device is expander,; use /c0/xp download" would occur when updating expander firmware - (SCGCQ00934755)
1.16.10 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Fixed an issue where no StorCLI error message is displayed when attempting to create a VD with WB policy on iMR HBA (SCGCQ00885617)
- Fixed an issue where controller status shown between MSM and StorCLI may contain false flash errors (SCGCQ00888470)
- Fixed an issue StorCLI PD firmware upgrade fails due to ATA Passthrough command being built incorrectly for download microcode (SCGCQ00862914)
- Fixed an issue StorCLI does not display E252/E253 enclosure info on an 84016 SCGCQ00868143)
- Corrected StorCLI behavior and messages between consecutive expansion operations of RAID Volume (SCGCQ00870429)
- Fixed an issue RAID level migration is not happening from 0 to level 1(SCGCQ00873770)
1.14.12 - Moderate Impact/Low Probability of Occurrence
-------
Fixes:
- Incorporated StorCLI MegaRAID 6.6 stream
Enhancements:
- Added ability to print SATA drives phy error counters and reset them (SCGCQ00735171)
- Added consistent sorting of controllers using bus, device, function (SCGCQ00696872)
- Added ability to enable or disable 512e support (SCGCQ00351234)
- Added support for Self-Encrypting Drives in JBOD mode (SCGCQ00755527)
- Added ability for VMWare version to be run from any directory (SCGCQ00642230)
- Added ability to display NCQ enabled/disabled status of every SATA drive (SCGCQ00564477)
- Added ability to create a RAID00 (SCGCQ00350668)
- Added ability to display the Patrol Read Start Time (SCGCQ00564474)
- Added learn cycle progress information in show learn command (SCGCQ00644984)
- Added support for uneven spans (SCGCQ00349548)
- Added support for lmrc driver (SCGCQ00433703)
- Added 240 Virtual Drive support (SCGCQ00693042)
- Improved Punctured Block logging (SCGCQ00342399)
1.12.15 - Moderate Impact/Low Probability of Occurrence
-------
Fix(es):
- Prevent storCLI from allowing users to enable JBOD mode on
controllers that do not support JBOD mode.
- Updated CACHEBYPASS command to line up with user expectation. When CACHEBYPASS is set, the user wants the cache to be bypassed. In previous versions of storcli, setting CACHEBYPASS actually disables the bypass.
1.07.07 - Moderate Impact/Low Probability of Occurrence
-------
Enhancement(s)
- Added support for ServeRAID M1215 SAS/SATA Controller
Fix(es):
- Fixed an issue where segmentation faults may occur in Linux.
- Added help information for resolving vd creation command fails with 'Memory Exhausted' message in SLES 11 OS.
- Fixed an issue where estimated time left, which range from seven or more days for Consistency Check and rebuild operations, are not displaying.
1.04.07 - Moderate Impact/Low Probability of Occurrence
-------
Enhancement(s)
- Added support for ServeRAID M5210e and ServeRAID M5210
Fix(es):
- Fixed an issue where a command failure results in subsequent commands and actions failing.
- Fixed an issue where storCLI reports a segmentation fault when running the command to downgrade the controller to iMR.
- Added help file for for storcli /cx/dx set security
- Fixed an issue where the "show ctrlcount help" command is not displaying properly.
- Fixed an issue where a failure is displayed in the output for querying dimmer switch information.
- Fixed an issue where the user is not able to set securitykey on a controller, if the securitykey was set through MSM.
- Fixed an issue where the virtual drive creation command does not give any error message when the user tries to create a private information virtual drive using normal physical drives.
- Fixed an issue where starkly displays a firmware flash successfully completed message even though the flashing failed.
- Synced the pause pr command with show pr command to show correct PR Current State.
- Fixed an issue where enabling online controller reset rate (OCR) from storCLI actually disables the controller property.
1.03.11 - Initial release
-------
