Lenovo YUM Repository
Release and Change History








Bundle Release Information:
Targeted Server Family (Machine Type): ThinkSystem SR650 V2 (7Z72, 7Z73)
Targeted Operating System: SLES15SP4
YUM Repository Build Date: 2024_05_10

YUM Repository Release Version: SIAgile23-1

Device:
ThinkSystem RAID 540-16i PCIe Gen4 12Gb Adapter Part Number: 4Y37A78835
Feature Code: na
PCIe Sub Vendor ID: 0x1D49
PCIe Sub Device ID: 0x0506


Release History:

Release Change History Documents

Lenovo RAID Adapter Linux Firmware



BIOS and Firmware Update for ThinkSystem RAID 540-x Adapters

Supported Adapters:  
ThinkSystem RAID 540-8i PCIe Gen4 12Gb Adapterr  (4Y37A78834)
ThinkSystem RAID 540-16i PCIe Gen4 12Gb Adapter   (4Y37A78835)
NOTE TO SERVICE - Reference RETAIN #N/A

Version 52.27.0-5216 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:7.27.00.0
	UEFI Driver:0x071B0200
	HII: 07.27.04.01
	IMR FW: 5.270.01-3950
    package 52.27.0-5216
MR 7.27

Defects:
Possible division or modulo by zero in enclosure management code.(DCSG01224310
HBA discovery failed with Phase 24 Storelib and StorelibTest(DCSG01207008
7.23 PA1: Data abort very early Start of Day(DCSG01225578
PEX89000: Fix function parenthesis in packet generator functions(DCSG01247963
MegaRAID 7.23: Firmware continuously logging "PESTATUS_DEVHANDLE_OUT_OF_RANGE" during crash dump(DCSG01288261
Skip Enclosure Power Cycle test for OEM BST as it is not relevant and results in failure(DCSG01303587
Firmware reports dual ports for SATA drives.(DCSG01352291
Fix Kill Adapter when powering off one of the attached enclosures(DCSG01217941
Fix for the MPB test(DCSG01209348
System restarts by itself and PL Fault 00005854 LinkRegister 01475093(DCSG01304319
Hardware Workaround:Link between Controller and expander not always recovering after link reset(DCSG01196230
Locate LED operation does not work for NVMe drive slot on UBM backplane(DCSG01230479
Same slot number is assigned to x1 link width drives connected to consecutive controller PHYs when an I2C backplane detection fails(DCSG01375808
Firmware is not incrementing the DFC Change Count value when there is a DFC change detected by the firmware.(DCSG01287092
SPILIB2: AutoStore command causes NVSRAM to ignore write enable comand(DCSG01218898
Secure Boot: Key mismatch error after FW image with 3K SHA3 256 w/0 ASN1 Header(DCSG00987745
MR_7.24: firmware fault on 9560 megaraid card upon malformed sense command(DCSG01331157
Too much text returned for TTY Read(DCSG01373054
[Aero/Ventura] Add check for Sense Data size(DCSG01178348
Build all failed on firmware tip code(DCSG01381053
LBA information missing from sense data with Medium Error Sense Key for SATA drives.(DCSG01183332
Export security does not work(DCSG01350835
Series 96xx: RMC SPI1 interrupt may assert when workaround is removed(DCSG01254315
Certain DS spin up sense codes are not filtered even with filtering enabled(DCSG01253216
MR7.24 Excessive prints while IO's are running(DCSG01339937
Enable encryption command enables security on multiple drives(DCSG01346635
While setting WCE(Disk Write Cache)=0 for JBOD; Firmware throws error mode_sense_10 buffer requested 400 but available 4, command failed.(DCSG01365204
MegaRaid7.23: firmware hit assertion failure memory.h at line 447: isInAddressibleRange(physAddrLow)(DCSG01310030
Fix inconsistent delimiter in Megamon command(DCSG01328543
Use correct flags in mbedTLS build for PEX89000(DCSG01317350
Uninitialized scalar variable access in UBM Backplane management and I2C driver code.(DCSG01339421
PCI slot and host serial number is set to default values.(DCSG01188813
Controller hit Fatal error with exception when run PR and CC at same time(DCSG01267776
NVMe Encapsulated MPI command not failed when it is blocked by IO Unit Page 13.(DCSG01294635
Continuation of defect 1304319 around unexpected system restart. Use this to further polish/harden the solution.(DCSG01328744
Update M.2 boot PSOC v1.17 caused Firmware hit ERROR: Exception Handler Called(DCSG01239775
IT controller firmware sending MCTP version numbers in reverse order(DCSG01234654
Aero: Incorrect topology phys memory allocation(DCSG01185588
Reading IO Unit Page 13 returns junk data(DCSG01292339
Fix controller info on NVMe Clock mode support when in SAS SATA only profile(DCSG01321714
LSA 7.23: Rebuild background operation progress bar disappears only after manual refresh.(DCSG01262337
C0:[141]:[Error] Signing Buffer Failed Sts:2 mesg after import successfully the certificate and reboot(DCSG01270486
Enable the TTY Replace setting in NVDATA(DCSG01333745
Self test aborts when Open Zone command issued on a Security locked drive(DCSG01194141
Fix too much OOB debug prints in the firmware log in iMR(DCSG01232395
Fix print statements in some debug firmware(DCSG01324759
Storcli hangs with no output after running script cleaning up debug variables.(DCSG01341519
Io Unit Control with Remove device fails if MPI function blocking is enabled. IO Unit Page 13 is writeable.(DCSG01270812
Phase 24 Code analysis tool Defects related to SPDM(DCSG01224346
[SATA] SATA Initialization fails on certain large capacity SATA drives(DCSG01194600
Fix underflow in print firmware(DCSG01353729
Update copyright information in the header file.(DCSG01266013
QErr value in Control mode page for NCQ SATA devices is set to 0 instead of 1.(DCSG01375632
Fix the size expression in a profile debug function(DCSG01272481
Fix Inconsistency in delimiter usage in mfc print(DCSG01328526
7.23 Alpha: BGOps appear to not be monitored properly(DCSG01285341
Build all failed on firmware tip code(DCSG01343959
Foreign Config import Error message not proper in HII(DCSG01089538
Rebuild did not start on dedicated hotspare when one member drive was failed(DCSG01320150
[SATA Only] NCQ Errors observed with running Read/Write IOs along with SCSI Unmap to SATA drive(DCSG01254091
MegaRAID 7.23: Running get snapdump and delete snapdump simultaneously (get snapdump first, immediately followed by delete) causes a get failure(DCSG01248884
Flash / upgrade from Release Order Package 4567 to Release Order Package 4601 failed on JBOD mode Ctrl (profile = 20)(DCSG01312941
Firmware was not repairing an NVMe drive with detached Inactive Namespace.(DCSG01321255
SAS drive keeps failing SCSI TUR with Check condition due to Controller not sending Periodic Notify (Enable Spinup)(DCSG01232852
Preboot Trace Buffer (PTB) disable operation fails in preboot application HII(DCSG01186641
BST Failure: Buffer Overflow Assertion During TTY Retrieval(DCSG01233951
Found PR not paused when scheduled consistency check starts(DCSG01292937
Disable SATA protocol when in optical mode(DCSG01194126
PSOC details are displayed with discrete logic iMR controller(DCSG01359864
9500 Series- host with eight PHY controller hangs during warm reboot(DCSG01289054
Secured configured drives changing to unconfigured after reboot(DCSG01249672
SPILIB2: Series 9700 Chip Select Timing registers default to zero(DCSG01182027
Drive stays in UBAD state when doing running drive insertion/removal test(DCSG01349665
BST Failure: Exception During 95xx Cache Offload BST(DCSG01236056
Fix wrong drive temperature information on SATA drive models that do not support temperature reading(DCSG01265562
Cache offload power and time values updates for 8G controller(DCSG01195653
Filter extra error message for frame allocation(DCSG01311743
NVMe device connected to PCIe switch is not discovered by controller firmware on boot up(DCSG01260624
BST Failure: CFGI Fault with Latest 7.23 XSD(DCSG01246068
Import certificate slot chain operation fails on SPDM enabled controllers(DCSG01200707
REST client does not reflect the latest drive firmware version after firmware update(DCSG01225086
On eight PHY SKUs, Firmware should disable PCIe packet processing for second SAS/PDB core.(DCSG01304303
Clean does not remove signing artifacts(DCSG01360624
Firmware console command 'pl eminfo' shows no PCIe support for a PCIe supported UBM backplane Device Face Connector.(DCSG01285442
PEX 89000: synthetic mode BST for B0 board(DCSG01236975
Uninitialized pointer access in UBM Backplane management code.(DCSG01225064
PEX89000: DevBst Fix for sensorDisplay CLI(DCSG01248992
Confusing ETTY prints near controller reset while creating R5 virtual disk with three drives(DCSG01383891
Build all is failed due to Error: NVDATA Major Versions do not match!(DCSG01258017
Missing stack frames when an exception occurs(DCSG01371672
MR_7.23: Storcli event during firmware upgrade needs correction.(DCSG01228280
observed when diagnostic register dump is performed while running IO to the drives. Description Of(DCSG01227332
[NVMe] Mode F Firmware download to certain NVMe drives fails.(DCSG01286617
Fix drive link speed reporting due to the fact that drive negotiated down link speed after initial link up(DCSG01288864
Missing fields in Manufacturing Page 7 in Snapdump(DCSG01321763
Running show security SPDM cmd failed(DCSG01349508
MegaRAID 7.22: Trying to validate DCSG01234817 and seeing similar issue and a hard hang(DCSG01363017
Target mode controller port width degrades following host resets/power cycles with autoport config disabled(DCSG01325599
PEX89000: Do not use use_frame_pointer compiler flag mbedTLS compilation(DCSG01282885
Fixes for the TTY Replace test case(DCSG01249618
Firmware summary notes needs to be updated to remove 94xx boards references(DCSG01271551
While generating the snapdump, firmware hit the data abort exception(DCSG01216058 (Port Of Defect DCSG01351467)
Drive running sanitize overwrite becomes UBUnsp after a cold boot(DCSG01174553 (Port Of Defect DCSG01270388)
Controller cache has been lost seen during Cache Offload Loop test(DCSG01108247 (Port Of Defect DCSG01166476)
Assertion when playing copyback Write Journaling entries on warm reboot(DCSG01310309 (Port Of Defect DCSG01314116)
[NVMe] Some NVMe drives do not link up on certain OEM backplanes.(DCSG01193134 (Port Of Defect DCSG01196465)
MegaRaid7.23: firmware hit assertion failure memory.h at line 447: isInAddressibleRange(physAddrLow)(DCSG01310030 (Port Of Defect DCSG01322278)
Firmware crashes after reconstruction completes and IO running(DCSG01292231 (Port Of Defect DCSG01301298)
During OCR, a snapdump was generated by FW due to "Assertion failure in fw\hw\pbam\serial.c at line 2413: IntNesting==0"(DCSG01175907 (Port Of Defect DCSG01176190)
MegaRAID 7.22: Trying to validate DCSG01234817 and seeing similar issue and a hard hang(DCSG01363017 (Port Of Defect DCSG01364478)
Foreign Config import Error message not proper in HII(DCSG01089538 (Port Of Defect DCSG01301413)
for JBODs, not setting physical drive state change committed bit in NVRAM.(DCSG01285247 (Port Of Defect DCSG01351187)
MR_7.24: firmware fault on 9560 megaraid card upon malformed sense command(DCSG01331157 (Port Of Defect DCSG01351139)
While setting WCE(Disk Write Cache)=0 for JBOD; Firmware throws error mode_sense_10 buffer requested 400 but available 4, command failed.(DCSG01365204 (Port Of Defect DCSG01365379)
While generating the snapdump, firmware hit the data abort exception(DCSG01216058 (Port Of Defect DCSG01351468)
Flash / upgrade from Release Order Package 4567 to Release Order Package 4601 failed on JBOD mode Ctrl (profile = 20)(DCSG01312941 (Port Of Defect DCSG01316809)
Fix Kill Adapter when powering off one of the attached enclosures(DCSG01217941 (Port Of Defect DCSG01229838)
While setting WCE(Disk Write Cache)=0 for JBOD; Firmware throws error mode_sense_10 buffer requested 400 but available 4, command failed.(DCSG01365204 (Port Of Defect DCSG01365380)
IO tool fails while running IO and Online Controller Reset in a loop(DCSG01206038 (Port Of Defect DCSG01233670)
Storcli hangs with no output after running script cleaning up debug variables.(DCSG01341519 (Port Of Defect DCSG01358591)
Firmware crashes after reconstruction completes and IO running(DCSG01292231 (Port Of Defect DCSG01302229)
IOC Page 7 does not report the updated "SASNotifyPrimitiveMasks"(DCSG01220829 (Port Of Defect DCSG01222353)
SATA, Fault 0x5919 seen during write same error and task managements(DCSG01176562 (Port Of Defect DCSG01228270)
Secured configured drives changing to unconfigured after reboot(DCSG01249672 (Port Of Defect DCSG01257018)
Drive stays in UBAD state when doing running drive insertion/removal test(DCSG01349665 (Port Of Defect DCSG01372497)
Drive running sanitize overwrite becomes UBUnsp after a cold boot(DCSG01174553 (Port Of Defect DCSG01270380)
Controller fault observed while running cache offload cycles with heavy IOs(DCSG01342893 (Port Of Defect DCSG01351132)
For un-configured bad foreign drive import and clear option buttons are visible in application(DCSG01315519 (Port Of Defect DCSG01351155)
Erase operation fails on OEM specific UBM backplane during UBM controller firmware update.(DCSG01289710 (Port Of Defect DCSG01294066)
Fix to handle TTY Flash with write error(DCSG01077025 (Port Of Defect DCSG01287096)
Direct attached devices do not link up in case SEP backplane detection is configured in NVData(DCSG01285763 (Port Of Defect DCSG01286648)
Assertion failure seen when expander resets and phy on & off executed in loop(DCSG01192071 (Port Of Defect DCSG01351483)
Revert SATA Init timeout changes(DCSG01252414 (Port Of Defect DCSG01255751)
Flash / upgrade from Release Order Package 4567 to Release Order Package 4601 failed on JBOD mode Ctrl (profile = 20)(DCSG01312941 (Port Of Defect DCSG01316817)
Firmware flash followed by expander reset hit the Exception(DCSG01234817 (Port Of Defect DCSG01351403)
MR_7.24: firmware fault on 9560 megaraid card upon malformed sense command(DCSG01331157 (Port Of Defect DCSG01351138)
Fix Kill Adapter when powering off one of the attached enclosures(DCSG01217941 (Port Of Defect DCSG01229841)
Change spinup mode while SATA link reset is occurring(DCSG01161733 (Port Of Defect DCSG01231494)
for JBODs, not setting physical drive state change committed bit in NVRAM.(DCSG01285247 (Port Of Defect DCSG01351186)
Firmware crashes after reconstruction completes and IO running(DCSG01292231 (Port Of Defect DCSG01301299)
Update NVDATA Major version(DCSG01258013 (Port Of Defect DCSG01270040)
For un-configured bad foreign drive import and clear option buttons are visible in application(DCSG01315519 (Port Of Defect DCSG01351156)
NVMe response buffer differs from host for get smart health information(DCSG01118222 (Port Of Defect DCSG01376667)
Sanitize (Block Erase) along with shutdown sequence caused assertion in firmware. (NVMe Only)(DCSG01358573 (Port Of Defect DCSG01371174)
Foreign Config import Error message not proper in HII(DCSG01089538 (Port Of Defect DCSG01304258)
Controller fault observed while running cache offload cycles with heavy IOs(DCSG01342893 (Port Of Defect DCSG01351130)
Firmware flash followed by expander reset hit the Exception(DCSG01234817 (Port Of Defect DCSG01351402)
Assertion when playing copyback Write Journaling entries on warm reboot(DCSG01310309 (Port Of Defect DCSG01314121)
Import certificate slot chain operation fails on SPDM enabled controllers(DCSG01200707 (Port Of Defect DCSG01249471)
Assertion failure seen when expander resets and phy on & off executed in loop(DCSG01192071 (Port Of Defect DCSG01351484)
MegaRaid7.23: firmware hit assertion failure memory.h at line 447: isInAddressibleRange(physAddrLow)(DCSG01310030 (Port Of Defect DCSG01322276)
Assertion when playing copyback Write Journaling entries on warm reboot(DCSG01310309 (Port Of Defect DCSG01314120)
M.2 NVMe drive initialization failed after warm reset(DCSG01264359 (Port Of Defect DCSG01301951)
[VSes] Number of slots reported incorrectly in certain OEM backplane.(DCSG01200427 (Port Of Defect DCSG01215896)

EnhancementRequests:
Use finalize bit hardware capability to generate SHA(DCSG01265112
Reduce On-Chip Memory Usage: NVME(DCSG01338107
Handle SED drive state when the drive get into AUTHORITY_LOCKED_OUT(DCSG00966551
SPILIB2: Add interrupt disable and clear to all init paths(DCSG01235869
Update Enterprise Key Management KEY FAILURE boot message description(DCSG01321257
Add new field overrideSlowArrayThresholds in XSD to enable or disable slow array logic(DCSG01289615
SBLIB: Add interface APIs to support Security Version(DCSG01239235
Added support for Extended Linear Address in hex image parsing for UBM6 backplane firmware update(DCSG01218275
Fix GET MCTP VERSION Response to Invalid Message Type Number(DCSG01207379
Add support for PCI Ids of OEM controllers(DCSG01218309
Add API changes to support option to filter spin up sense events through NVDATA field filterDSSpinUpEvents(DCSG01218513
Handle interrupted TTY reads when TtyLogInFlash is disabled(DCSG01245875
TLER (Time Limited Error Recovery) for MR7 Controllers(DCSG01063803
Add New field in NVDATA to enable or disable spin up sense events(DCSG01218525
Add New field in NVDATA to enable or disable spin up sense events(DCSG01218525
Messages does not differentiate in Device Manager Retry command for success and failure conditions(DCSG01320346
Add Missing PSoC Firmware Files for DCSG01291552(DCSG01301007
Aero - SecureBoot: Added debug messages to the ring-buffer when the FW download operation fails(DCSG01132478
Implement PCIe reference clock control in applications.(DCSG01232265
Code Coverage Improvement: Firmware changes to add Random Number tests to BST(DCSG01273668
Reduce On-Chip Memory Usage: AES(DCSG01345551
Reduce On-Chip Memory Usage: Megamon(DCSG01334551
Updated Package build option in release scripts(DCSG01360774
Adding a print string when LED blink status is set to BAD(DCSG00927793
Firmware: With TTYloginflash disabled, provide the eTTY log when the user requests for the term log(DCSG01187516
Qualify OEM BiCS5 flash devices for cache offload functionality(DCSG01311375
Reduce On-Chip Memory Usage: Hardware Tests(DCSG01334967
Reduce On-Chip Memory Usage: Diagnostics(DCSG01336164
Add support to change Enterprise Key Management support through command line(DCSG01155012
Modify the cache offload memory layout to support future NAND parts(DCSG01363836
Enhance Reconstruction error handling to avoid crash with invalid physical drive(DCSG01368554
Add a TtyReplace switch to NVDATA(DCSG01232969
Reduce On-Chip Memory Usage: Snapdump(DCSG01333402
Firmware: Enhanced NVMe Recovery Process(DCSG01220515
Add compiler version checking to the MegaRAID firmware build(DCSG01278550
iMR Snapdump: include Megamon commands in TTY Log(DCSG01365338
Adjust comment entry to match API changes(DCSG01229786
Update SPI Lib to latest(DCSG01215946
Reverting changes from ER DCSG01155012(DCSG01248730
[Code Coverage] Include CTC files in firmware code and create a build type that includes CTC code.(DCSG01132120
Reduce On-Chip Memory Usage: Enclosure(DCSG01345411
SBLIB: Add all OID compatibility algorithm to Avenger build(DCSG00346387
SPILIB2: Change build options to match firmware options(DCSG01171492
Add NVDATA bit for allow Enterprise Key Management enable/disable support(DCSG01218843
Add IO Unit page 13 handling to Block/Allow MPI functions(DCSG01214245
Reverting API change for external key management feature enable/disable support(DCSG01248890
Add a generic event to identify the reset type(DCSG01344405
API change to add more Enclosure subtypes to support OEM backplanes(DCSG01209717
Comment changes for TTY Replace(DCSG01272267
Re-enable SPILIB2 and Fix MPB Erase Issues(DCSG01200182
Code Coverage Improvement: add an ETTY test case(DCSG01356753
Add Firmware Version 3 for PartNumbers 25731 and 25931 to PSoC Catalog Image(DCSG01291552
Capture Event info as a part of Snapdump(DCSG00965557
[SNTL] Update SCSI Format Translation for NVMe devices(DCSG01137935
Add custom change number to MBEDTLS to track which version is in use.(DCSG01267947
Aero FW-Download: when writing bootloader to the main region, write the signature bytes last(DCSG01154887
OOB Debuggability improvement(DCSG01194531
Add Capability Bit for Driver Dump Mode Status to MFI_CAPABILITIES(DCSG01321223
SPILIB2: Read the ISSI function register on init to detect incorrect configurations(DCSG01288804
Unexpected Sense Codes related to Dimmer Switch should not be logged in cases where FW has spun down PD(DCSG01171916
Add Firmware Version 19 and 18 for New OEM PartNumbers 29652 and 32052 to PSoC Catalog Image (Part 1)(DCSG01350783
API change for Implementation of PCIe reference clock control from applications.(DCSG01286990
Code Coverage Improvement: clean up dead code in TTY and timer files(DCSG01269785
Add a TtyReplace switch to NVDATA(DCSG01232885
Reduce On-Chip Memory Usage: I2C(DCSG01345439
Add Firmware Version 10 for PartNumbers 6021, 14790, and 14798 to PSoC Catalog Image(DCSG01296892
Fix Part Number Header Verbiage(DCSG01375705
Generate a link speed change event for drives when the initially negotiated link speed gets changed(DCSG01348250
Removed OEM specific code(DCSG01187339
Handle PD Manual Status change while BGI/CC/INIT is active/Paused and adjust consistency status of LD(DCSG01188329
LED updates and VSES commands from host are blocked during UBM BP Firmware update(DCSG01187546
Upgrade ARM compiler version(DCSG01331364
SPDM library: Add support for SPDM v1.0(DCSG01137730
Add a new bit to parameter page 0(DCSG01224690
Capture additional controller info in Snapdump(DCSG01327223
Add ApSHA changes(DCSG01209350
Add new feature to enable or disable slow array logic in firmware(DCSG01272081
Add Firmware Version 17 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01314019
Reduce On-Chip Memory Usage: Drive Performance Monitor(DCSG01333825
Enable DS event filtering in firmware based on filterDSSpinUpEvents NVDATA setting(DCSG01226496
Firmware: Add DFT for Improve R1 Clustered Medium Error handling(DCSG01232890
Implement incomplete firmware handlers for the SCSI commands as per the latest SCSI NVMe Translation Layer spec - V1.08(DCSG01308277
API changes to set the default execution interval for Consistency check and patrol read through NVDATA(DCSG01358207
Add new interface APIs to Secure Boot Library(DCSG01099719
Add PEX89000 build support for libmbed tls.(DCSG01175822
Add an API to format the ETTY to a buffer(DCSG01208404
Updated release scripts for verifying Firmware build status(DCSG01350607
Revert NVDATA change for allow external key management feature enable/disable support(DCSG01248896
SPILIB2: Add FRAM support(DCSG01245618
Code Coverage Improvement: add the semaphore tests to BST(DCSG01270488
Run PEX89000 devBST on B0 board(DCSG01247942
SPDM 1.1 : Upgrade to MbedTLS version 2.26.0(DCSG01060374
Discontinue Firmware Release for 94xx Series of chips(DCSG01240537
Add support for OEM target for including the latest sblib(DCSG01263709
Enhance RMC log parser for new reference clock timeout(DCSG01315146
Remove custom library prefix from builds(DCSG01170510
SPILIB2: Integrate new 9700 series headers and add support for FRAM(DCSG01292279
Add new event for Physical Disk link speed change.(DCSG01327217
Firmware: Make autorebuild behavior consistent for end customers(DCSG01240282
Reduce On-Chip Memory Usage: Disk Encryption(DCSG01336490
Reduce On-Chip Memory Usage: Embedded CPU Debug(DCSG01334173
SPILIB: 97xx - Change dummy byte value to 0xFF's(DCSG01216772
Add Dummy Part Number Image to Catalog for Old 15987 Part Number PSoCs(DCSG01373884
Make adjustments for TTY Clear when TTYloginflash is disabled(DCSG01225741
Improve RLM operation time when no host IO activity is on going(DCSG01186257
Use event based wait for browser automation during release process(DCSG01133010
SBLIB: Clean up code for external use(DCSG01150489
Added Enable Enterprise Key Manager Support bit to MegaRaid CTRL_PROP(DCSG01208216
Firmware: Prevent installation of inappropriate FW image on Intel branded MR/iMR adapters(DCSG01272302
PLDM single image support(DCSG01249347
Enhance SuperCap Relearn Logic to Not Prematurely Set App Learn Failures and Timeouts(DCSG01383159
Firmware: SPDM Support for 954x boards(DCSG01311369
Firmware: Improve R1 Clustered Medium Error handling(DCSG01187519
Add support for OEM UBM backplane(DCSG01209669
Add Firmware Version 4 for PartNumber 15463 to PSoC Catalog Image(DCSG01378374
SCONS: Update the back trace symbol generator so that it supports unlimited symbols(DCSG01230985
Code Coverage: improved error handling when dumping counters(DCSG01224606
Reduce On-Chip Memory Usage: Constants(DCSG01342382
SBLib: Add API to discern whether the EFUSE is full(DCSG00989785
Firmware: Implement REFCLK control in HII(DCSG01291368
Reduce On-Chip Memory Usage: Strings(DCSG01337295
PEX89000: Add configuration for the PEX89000 B0 BST setup(DCSG01256006
Build Improvement: clean needs to apply to debug builds as well(DCSG01300541
MegaAPI: Add API Controller Properties for overriding slow array thresholds(DCSG01288908
Add Firmware Version 19 and 18 for New OEM PartNumbers 29652 and 32052 to PSoC Catalog Image (Part 2)(DCSG01350841
PLDM - Add UBM firmware update changes under the compilation macro(DCSG01250826
Update Aero iMR/MR to the latest secure boot library(DCSG01198693
Leverage Driver Dump Mode bit in MFI_CAPABILITIES to determine if host is in dump mode(DCSG01344379
Code Coverage: build changes to verify that supported tools are being used(DCSG01254595
Reverting XSD change for external key management support feature(DCSG01248908
PL Firmware: SFF-TA-1005 Version 1.4 Support(DCSG01214256
Added a generic event to identify the reset type.(DCSG01315620
Add API changes to support slow array logic override through NVDATA field overrideSlowArrayThresholds(DCSG01289475
Update config file for PEX89000 A0 devBST(DCSG01235384
Support SPDM v1.0 for OEM controllers(DCSG01135013
Firmware: Add a SAS/SATA only profile(DCSG01311360
Add Electrical Information to Cache Offload Info Dump(DCSG01327220
Revert Port Name Changes in Redfish Events(DCSG01187327
Firmware: Support Long Lock Delay Times when Negotiating to a 6G SATA Drive at 3G(DCSG01253833
Add Firmware Version 18 for PartNumbers 29211, 29651, and 29810 to PSoC Catalog Image(DCSG01345892
Enhancement in preserving NVRAM settings in snapdump(DCSG01289418
Update SB Lib to latest(DCSG01224363
SPDM: Upgrade the latest SPDM Library in PH26(DCSG01219141
Improve iMR null pointer handling so that exceptions are generated(DCSG00996946
Capture physical drive and logical drive allowed operations in Snapdump(DCSG01327224
PL firmware workaround for UBM Backplane firmware flashing issue in OEM specific Backplane(DCSG01237118 (Port Of EnhancementRequest DCSG01252393)
PL: Enable the UBM firmware update support for OEM specific UBM backplane.(DCSG01233264 (Port Of EnhancementRequest DCSG01252355)
Firmware: Add a SAS/SATA only profile(DCSG01311360 (Port Of EnhancementRequest DCSG01378362)
Firmware: Add a SAS/SATA only profile(DCSG01311360 (Port Of EnhancementRequest DCSG01350767)
IOP: Rework MCTP packet validation code for workaround for some multi-segment servers(DCSG01289379 (Port Of EnhancementRequest DCSG01328386)
[9500] Add support for host phys/lanes in Port Status Green GPIO(DCSG01207029 (Port Of EnhancementRequest DCSG01251940)
Add support for new product specific MCTP Event(DCSG01149990 (Port Of EnhancementRequest DCSG01268764)
Enhance Reconstruction error handling to avoid crash with invalid physical drive(DCSG01368554 (Port Of EnhancementRequest DCSG01370842)
Add support for OEM specific SAS 4 expander based enclosure with 950x controllers(DCSG01351490 (Port Of EnhancementRequest DCSG01363691)
	

Version 52.22.0-4775 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:7.22.00.0
	UEFI Driver:0x07160300
	HII: 07.22.03.00
	IMR FW: 5.220.01-3784
    package 52.22.0-4775
MR 7.22

Defects:
-Copyright year needs to be corrected in ROC firmware print.(DCSG01396947)
-Locate LED operation does not work for NVMe drive slot on UBM backplane.(DCSG01230479)
-Updated the forceUpdate format in PLDM header generation Tool.(DCSG00106563)
-Locate LED operation does not work for NVMe drive slot on UBM backplane.(DCSG01230479)
-WriteCache RDE alerts are logged irrespective of the volume cache policy(DCSG01088107
-RDE - REST client displays the controller cache state as 'Disabled' instead of 'UnavailableOffline' when a failed energy pack is connected(DCSG01093471
-Aligning RDE Port MaxSpeedGbps per the latest spec(DCSG01098703
-RDE Port Schema CurrentSpeedGbps property to be populated with aggregate of current speeds of connected devices(DCSG01098717
-RDE_VolumeSchema-Encryption and EncryptionType to be displayed conditionally(DCSG01098912
-RDE - Encryption Status drive resource property must be displayed if the drive is a Self Encrypting Drive(DCSG01098917
-RDE VolumeSchema - WriteHoleProtectionPolicy to be conditional for Raid types that use Write Journaling(DCSG01102935
-Fix sliced LD secure erase resume after power cycle or OCR(DCSG01107534
-RDE Port Schema: CurrentSpeedGbps and MaxSpeedGbps shown as a negative value(DCSG01108315
-Redfish NVMe DurableName to be displayed in IEEE-defined 64-bit Extended Unique Identifier (EUI) format(DCSG01111791
-make all is compiling now(DCSG01111915
-RDE : Volume schema WriteCacheState property changed to "Degraded" during volume Transformation(DCSG01113836
-RDE Volume Schema - State of Volume changed to 'Updating' while rebuilding(DCSG01120814
-RDE Read Compliance-Drive Schema Health changed to "Critical" and Status indicator to "Fail", when a Predictive Failure drive is made Offline(DCSG01120819
-LED updates and VSES commands from host are blocked during UBM BP FW update(DCSG01123121
-RDE : Volume schema InitializeMethod property should not show "Foreground" for Volume Erase Operation(DCSG01124997
-UBM Ctrl FW update - Block host request OCR(DCSG01132889
-Redundant Microcode update Complete event avoided - Restricting and Un-restricting PD during UBM Ctrl FW update is removed(DCSG01135144
-Corrected UBM Ctrl FW update Abort response to populate appropriate event(DCSG01143009
-UBM firmware update not happening on one out of two UBM controllers while rebuild operation was in progress(DCSG01148879
-ONLINE LED and Predictive Failure LED to be ON for specific OEM(DCSG01152693
-Updated EstimatedTimeBeforeSendingRequestFirmwareData(DCSG01155398
-Error values during PMSM preserved correctly(DCSG01155732
-Cancel update command response is set appropriately in the shim layer(DCSG01158535
-iMR 7.22 exceeds Max 8 SAS/SATA drives when more drives are inserted and they become Jbod.(DCSG01166723
-MR card failed to expose drives in Linux kdump(DCSG01170243
-PLDM Type 5 support for Downstream device enablement based on library support(DCSG01172419
-MR7.22PA1_Need to add bootKeyHalt to 0 for excessive drives(DCSG01173927
-Updated the common structure member values ,which are used during UBM BP update and MR controller FW update.(DCSG01175633
-Perc 11.4: During OCR, a snapdump was generated by FW due to "Assertion failure in fw\hw\pbam\serial.c at line 2413: IntNesting==0"(DCSG01175907
-MR7.22-Resetnow should be blocked for PSOC updates(DCSG01181534
-MR 7.22 PA2: 433T PSOC can't be flashed via storcli due to PN mismatch(DCSG01183086
-Configuration not exposed by MR on windows OS when device order is enabled(DCSG01184008
-MR FW not responsive to host interface after returning success to stop BGI / CC of an offline VD(DCSG01185811
-PEX88000 - Issue NF error to NIC card resulted in system crash(DCSG01186408
-fix sanitize block erase support on NVMe drive(DCSG01187755
-Firmware reports dirty cache lost in the UART log(DCSG01191291
-Assertion failure seen when expander resets and phy on & off executed in loop(DCSG01192071
-Assert Audit: fix printing when the analysis is restarted(DCSG01196023
-Code Coverage: fix SPDM path list in codeCoverageTool.py(DCSG01196255
-[VSes] Number of slots reported incorrectly in certain OEM backplane.(DCSG01200427
-Sanitize option seen in Apps when a drive is spundown by user(DCSG01201754
-While generating the snapdump, firmware hit the data abort exception(DCSG01216058
-Fix Kill Adapter when powering off one of the attached enclosures(DCSG01217941
-Firmware flash followed by expander reset hit the Exception(DCSG01234817
-PEX 89000: synthetic mode BST for B0 board(DCSG01236975
-Enclosure location is showing as "Internal" in LSA for Vses(DCSG01245355
-BST Failure: CFGI Fault with Latest 7.23 XSD(DCSG01246068
-PEX89000: Fix function parenthesis in packet generator functions(DCSG01247963
-Secured configured drives changing to unconfigured after reboot(DCSG01249672
-Controller hit Fatal error with exception when run PR and CC at same time(DCSG01267776
-Skip Enclosure Power Cycle test for OEM BST as it is not relevant and results in failure(DCSG01303587
-System restarts by itself and PL Fault 00005854 LinkRegister 01475093(DCSG01304319
-Enable the TTY Replace setting in NVDATA(DCSG01333745
-Fix wrong consistency state of Single drive R0 after setting physical drive offline then online(DCSG01141800
-MR7.21: Flash erase errors(DCSG01148422
-7.21 : Test bad flash in Megamon, found FW hit KA(DCSG01140493
-MR 7.21 Ventura FW Pk 4350 stops dumping data in FW log during OCR.(DCSG01156781
-Fatal firmware error detected after converted SATA SSD PD to JBOD(DCSG01112314
-CSCwb37148: SPDM programming got wiped out from Wlbur+Samishlake: Storage operations are failing.(DCSG01179653
-The Fault LED is on for the expander attached pre-failure EPD drive when rebooting the system(DCSG01172493
-FW logging CDB failure sense event twice for each failure(DCSG01149411
-[NVMe] Some NVMe drives do not link up on certain OEM backplanes.(DCSG01193134
-OOB SL\SLT NVMe Passthru : NVMe response buffer differs from host for get log information command for NVMe drives(DCSG01147859
-Unconfigured Bad SAS SSD drive is showing Media as HDD in LSA/Storcli(DCSG01196368
-Fix for the MPB test(DCSG01209348
-IO tool fails while running IO and Online Controller Reset in a loop(DCSG01206038
-[SATA] SATA Initialization fails on certain large capacity SATA drives(DCSG01194600
-Locate LED operation does not work for NVMe drive slot on UBM backplane(DCSG01230479
-Import certificate slot chain operation fails on SPDM enabled controllers(DCSG01200707
-Drive running sanitize overwrite becomes UBUnsp after a cold boot(DCSG01174553
-Fix to handle TTY Flash with write error(DCSG01077025
-Firmware crashes after reconstruction completes and IO running(DCSG01292231
-Foreign Config import Error message not proper in HII(DCSG01089538
-Assertion when playing copyback Write Journaling entries on warm reboot(DCSG01310309
-Flash / upgrade from Release Order Package 4567 to Release Order Package 4601 failed on JBOD mode Ctrl (profile = 20)(DCSG01312941
-Strocli show command displays incorrect number of physical drives count(DCSG01293599
-MegaRaid7.23: firmware hit assertion failure memory.h at line 447: isInAddressibleRange(physAddrLow)(DCSG01310030
-For un-configured bad foreign drive import and clear option buttons are visible in application(DCSG01315519
-Controller fault observed while running cache offload cycles with heavy IOs(DCSG01342893
-MR_7.24: firmware fault on 9560 megaraid card upon malformed sense command(DCSG01331157
-for JBODs, not setting physical drive state change committed bit in NVRAM.(DCSG01285247

Enhancements:
-Single PLDM fw update file that covers all controllers from that series.(DCSG00019356)
-UBM Controller Firmware Update support(DCSG01016704
-Aero - Shim layer support for PLDM Type 5 UBM Backplane Firmware Update(DCSG01070579
-Aero 9540 iMR controllers - Support for multiple PSOC images(DCSG01076542
-Parses the UBM FW image file(DCSG01080232
-shim layer changes for prepare and download(DCSG01083777
-Aero - Block SES monitoring and locate LED functionalities when UBM backplane firmware update is in progress(DCSG01088688
-Make branding compliance changes for new features including Sanitize support(DCSG01090347
-Allow FW downgrade for shenandoah(DCSG01093455
-New PNP ID addition(DCSG01101846
-RDE Read Compliance - Align to the latest Spec(DCSG01107680
-Calculate downstream devices length of QueryDownstreamIdentifiers command(DCSG01108419
-PLDM Type 5 - Set Downstream Device Component Update Failure Recovery Capability parameter of GetDownstreamFirmwareParameters command to 0(DCSG01123160
-Shim layer changes to add Vendor Defined descriptor support for PLDM FW update UBM Ctrl Downstream Device(DCSG01128935
-Reduce eTTY and Binary Trace Logic Stack Usage(DCSG01139030
-Add Additional PSoC 4 FWs to Catalog File(DCSG01157615
-Remove custom library prefix from builds(DCSG01170510
-97xx: SCONS changes are required for loading 97xx SBR(DCSG01171935
-Remove PSoC 5 OCP PSoC FW from Catalog Releases(DCSG01175916
-Check-in Cypress License Agreement into MR Cypress Code Tree(DCSG01177646
-Add Firmware Version 13 for PartNumber 29810 to PSoC Catalog Image(DCSG01179045
-Code Coverage Improvement: better handling of long strings in ETTY(DCSG01179424
-Reduce _vnprintf stack usage(DCSG01186456
-Code Coverage Improvement: Adjust Preprocessing in Snapdump(DCSG01194315
-Code Coverage: Add MPB test status(DCSG01195938
-Code Coverage Improvement: exclude development only functions(DCSG01196166
-Code Coverage: allow tools to be in other directories(DCSG01196286
-Add message when invalid phy is passed to get connector index(DCSG01197627
-Code Coverage: support all build target(DCSG01197780
-Code Coverage: support all build target -- fw_bld_tools(DCSG01199258
-Update OEM specific BST scripts to include mainline changes.(DCSG01200062
-Add New PSoC 5 OCP Channel and Megacell and PSoC 6 BGA Megacell Releases to PSoC Catalog Image(DCSG01203313
-Add Firmware Version 15 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01208354
-Add Firmware Version 16 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01209445
-Code Coverage Improvement: remove some constants from the Snapdump symbol file(DCSG01209495
-Updated OEM auto bst scripts(DCSG01212778
-Add API changes to support option to filter spin up sense events through NVDATA field filterDSSpinUpEvents(DCSG01218513
-Add New field in NVDATA to enable or disable spin up sense events(DCSG01218525
-Add NVDATA bit for allow Enterprise Key Management enable/disable support(DCSG01218843
-PEX89000: Add PEX89000 packet generator support to DevBst(DCSG01223198
-Add a new bit to parameter page 0(DCSG01224690
-SCONS: Update the back trace symbol generator so that it supports unlimited symbols(DCSG01230985
-Add a TtyReplace switch to NVDATA(DCSG01232885
-Add a TtyReplace switch to NVDATA(DCSG01232969
-Update config file for PEX89000 A0 devBST(DCSG01235384
-Run PEX89000 devBST on B0 board(DCSG01247942
-Revert NVDATA change for allow external key management feature enable/disable support(DCSG01248896
-Reverting XSD change for external key management support feature(DCSG01248908
-PLDM single image support(DCSG01249347
-PEX89000: Add configuration for the PEX89000 B0 BST setup(DCSG01256006
-Firmware: Prevent installation of inappropriate FW image on Intel branded MR/iMR adapters(DCSG01272302
-Add API changes to support slow array logic override through NVDATA field overrideSlowArrayThresholds(DCSG01289475
-Add new field overrideSlowArrayThresholds in XSD to enable or disable slow array logic(DCSG01289615
-Add Firmware Version 3 for PartNumbers 25731 and 25931 to PSoC Catalog Image(DCSG01291552
-Add Firmware Version 10 for PartNumbers 6021, 14790, and 14798 to PSoC Catalog Image(DCSG01296892
-Add Missing PSoC Firmware Files for DCSG01291552(DCSG01301007
-Optimize the default Consistency check and patrol read settings for decreasing the workload on drives(DCSG01339902
-Add Firmware Version 19 and 18 for New OEM PartNumbers 29652 and 32052 to PSoC Catalog Image (Part 1)(DCSG01350783
-API changes to set the default execution interval for Consistency check and patrol read through NVDATA(DCSG01358207
-Add new field consCheckAndPatrolReadExecFreq in XSD file to set the default execution interval for Consistency check and patrol read through NVDATA(DCSG01360727
-Spin up recovery. changes for supporting OEM drive issue(DCSG01168828
-PLDM library support on Aero iMR controllers(DCSG01176360
-Firmware: Add a SAS/SATA only profile(DCSG01311360

Version 52.22.0-4564 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:7.22.00.0
	UEFI Driver:0x07160300
	HII: 07.22.03.00
	IMR FW: 5.220.01-3694
    package 52.22.0-4564
MR 7.22

Defects:
-Unconfigured Bad SAS SSD drive is showing Media as HDD in LSA/Storcli.(DCSG01196368)
-Fix Kill Adapter when powering off one of the attached enclosures.(DCSG01217941)
-Firmware flash followed by expander reset hit the Exception.(DCSG01234817)
-Enclosure location is showing as "Internal" in LSA for Vses.(DCSG01245355)
-PEX89000: Fix function parenthesis in packet generator functions.(DCSG01247963)
-Release Note update for Downgrade firmware from 7.22 to & 7.2x.(DCSG01270046)
-IO tool fails while running IO and Online Controller Reset in a loop.(DCSG01206038)
-Import certificate slot chain operation fails on SPDM enabled controllers.(DCSG01200707)
-[VSes] Number of slots reported incorrectly in certain OEM backplane..(DCSG01200427)
-Updated the forceUpdate format in PLDM header generation Tool.(DCSG00106563)
-Controller Missing on some Power Cycle iterations.(DCSG01233716)
-[VSes] Number of slots reported incorrectly in certain OEM backplane..(DCSG01200427)
-Fix return status when there is no more target ID available at auto config.(DCSG01140002)
-Controller marks a drive UBUnsp if the server is rebooted while running Sanitize Overwrite.(DCSG01141274)
-Firmware hang observed during controller boot.(DCSG01142137)
-[Aero][SNTL] SNTL Generic command Status successful completion with no SenseKey is sending.(DCSG01146888)
-MR7.21: Flash erase errors.(DCSG01148422)
-Fix the check blocking FDE drive on Sanitize.(DCSG01156368)
-MR 7.21 Ventura FW Pk 4350 stops dumping data in FW log during OCR.(DCSG01156781)
-Fail the UBM firmware update request gracefully if Programming Update is not supported by the.(DCSG01159186)
-[Aero] "Couldn't init SBLI" error print seen in firmware uart during controller boot up.(DCSG01161361)
-Data Miscompare observed with sliced R5 Logical Drives during write(cache) policy change.(DCSG01161554)
-Update the error code when there is no target ID available for auto config EPD.(DCSG01163316)
-Generate BootMsg when more than 4 NVMe drives is inserted in the boot cycle at profile 41 for iMR.(DCSG01165091)
-Fix wrong persistent dev id due to profile change.(DCSG01166149)
-Aero iMR: FW did not block downgrade from MR7.22 (profile 41) to MR7.21 causing CTRL into safe mode.(DCSG01169605)
-NVMe drives behind 9460-16i controller doesnt discover on SOD.(DCSG01172751)
-Fix persistent Id clearing when profile is not changing.(DCSG01175414)
-Firmware asserts when reading the UBM backplane information and UBM controller firmware update in progress.(DCSG01132100)
PL is not returning proper sense information as part of UBM controller firmware update failure reply..(DCSG01145707)
-PL fails to report the UBM controller firmware update failure after receiving the bad checksum.(DCSG01148192)
-Controller cache has been lost seen during Cache Offload Loop test.(DCSG01108247)
-Discovery times out when connected to UBM backplane with x4 link width..(DCSG01165227)
-Secure erase is not working properly for UG Bad drive.(DCSG01106797)
-Diff drives shows as UG and sector size 0/blank in BRCM applications.(DCSG01145221)
FW asserts on executing scrutiny phy -speed command.(DCSG01089818)
-Support NVMe Width is displayed as "Yes" for RAID 940-8e controller.(DCSG01119307)
-Phy bad events seen for one of the Enclosure Valid Slot.(DCSG01088807)
-Updated the forceUpdate format in PLDM header generation Tool.(DCSG00106563)

Enhancements:
-Remove custom library prefix from builds.(DCSG01170510)
-SCONS: Update the back trace symbol generator so that it supports unlimited symbols.(DCSG01230985)
-Update config file for PEX89000 A0 devBST.(DCSG01235384)
-Blocking at MR FW and graying out at applications for changing the link speed for any UBM behind drives.(DCSG00950267)
-Add multiple SPI device access devBST tests on SPI0.(DCSG01003421)
-Partial configuration import events and messages in the utilities..(DCSG01070721)
-Cosim BST: Update the FW package content for file name changes (pci4armfw => pcifw).(DCSG01132044)
-Code Coverage: build improvements.(DCSG01135245)
-Create OEM PSoC FW Based Catalog File.(DCSG01136930)
-Update Atlas2 devBST script with filename changes.(DCSG01137350)
-PEX89000 BST ER: Two host flash boot feature BST Evaluation for COSIM.(DCSG01138480)
-Add PSoC Image Checking and FW Blocking for Aero iMR(DCSG01153976)
-Update PSoC MR FW Downgrade Block MFI_STAT to be More Clear.(DCSG01155856)
-Add Firmware Version 12 for PartNumbers 29211 and 29651 to PSoC Catalog Image.(DCSG01159010)
-Update link speed control bit in SAS PHY connection structure.(DCSG01164061)
-97xx: SCONS changes are required for loading 97xx SBR.(DCSG01164951)
-Add Firmware Versions 27 and 1 for PartNumbers 15987 and 25731 to PSoC Catalog Image.(DCSG01166118)
-Make API changes for new event FOREIGN_CFG_NON_IMPORTABLE_FOUND.(DCSG01168924)
-Code Coverage Improvement: update command line parsing in cfgi.(DCSG01169587)
-Code Coverage: add an identifier when dumping coverage data.(DCSG01170508)
-SPILIB2: 9700 Series core needs maximum continuous count initialized earlier.(DCSG01170965)
-SPDM 1.1 - Validate Certificate Chain during import operation.(DCSG01096875)
-Single PLDM fw update file that covers all controllers from that series.(DCSG00019356)


Version 52.20.0-4375 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:v7.20.01.0
	UEFI Driver:0x07140000
	HII: 07.20.07.00
	IMR FW: 5.200.01-3637
    package 52.20.0-4375
MR 7.20

Defects:
 Fix read wrong config page for NVMe drive behind Atlas(DCSG00954454
 SL OOB: NVME response buffer is not displaying user requested size of response buffer.(DCSG01151757
 MR7.20_Ventura+Windbond_CV learn fails(DCSG01127762
 MR_7.20 missing VD's after OCR and enclosure Pull/Push(DCSG01061674
 Remove SPDM debug logs from UART print(DCSG01022803
 [3408+ MR7.16] configurablePDCount would exceeded if set jbod on while UG drives are in spundown.(DCSG01032834
 FW hits KA when OCR Ctrl has pinned cache, while controller in Safe Mode(DCSG01061904
 CC pause and resume with OCR restarts the CC on VDs that have already completed CC(DCSG01047837
 MR7.19: Aero Ctrl global fault LED is not ON when there is unconfig_bad drive on the Ctrl(DCSG01027566
 iMR 7.20 FW keeps dumping a message to FW log for Encs "Analyzing Status Page"(DCSG01025079
 VSES : Multiple elements of SES page 0xA are assigned the same slot number(DCSG00973316
 Fix a math error in the Memory Pool creation firmware(DCSG01024464
 Performance drop seen with direct attached SAS/SATA drives(DCSG00980873
 Foreign drive import command was successfully executed, but the drive is still marked as a foreign drive(DCSG01039809
 PD Power State Set DCMD interface does not spin up Hot spare drives(DCSG01091672
 21B Alpha LSA: Foreign VD's, VD1 and VD2 names are not displayed in foreign config preview page.(DCSG00927138
 Performance drop seen with SAS/SATA drives in Windows using latest driver(DCSG00981706
 MR 7.20 PA2: truncated coverage data(DCSG01040242
 Reinstate ER 1010648(DCSG01025061
 FW Logs/termlogs should change the Copyright 2017-2022(DCSG01116760
 Blue Screens while collecting "pl dbg" logs(DCSG00984451
 22B:PSOC6 -PSOC download/flash fails having Cv/BBU in failed (bad) state(DCSG01140342
 UBM statistics data collection and UBM error handling fixes(DCSG00975065
 Atlas2 Veloce BST: Wait till MPT driver load complete in single host MPT testcase(DCSG01087297
 Unable to change current behavior mode to NONE from RAID-0 in JBOD personality(DCSG00970577
 Update SSUTimeout Fields Value in BIOS Page 1 to 0xF0(DCSG00982364
 Clearing the tty history with cli delete termlog command causes firmware to hang(DCSG01098208
 Coverity : Remove dead code(DCSG00982343
 Support NVMe Width is displayed as "Yes" for RAID 940-8e controller(DCSG01119307
 Fix MCTP flash firmware issue(DCSG01098220
 No Default value of DMA FIS Timeout(DCSG01028477
 Secure erase is not working properly for UG Bad drive(DCSG01106797
 MR7.20: Found a lot prints "C0:MfgMsg: Error reading device chemistry. I2C Error = 0x2" while PR(DCSG01044765
 MR7.19PA1_After COL locked VD fails to import after becoming unlocked(DCSG00962887
 Diff drives shows as UG and sector size 0/blank in BRCM applications(DCSG01145221
 Fix controller does not show foreign config and pinned cache correctly(DCSG01050353
 Expander show status is being marked unsupported in megaraid and switch configurations(DCSG00958041
 Imbalanced bandwidth performance with 2 x4 expanders connect to Aero IT controller(DCSG00950631
 Copyback status is displayed post clearing configuration(DCSG01039193
 FW asserts on executing scrutiny phy -speed command(DCSG01089818
 Firmware assertion while performing firmware download using offline method on PCIe switch configuration(DCSG00956089
 MR 7.20 PA2: Code coverage code stuck printing forever(DCSG01031802
 Drive secured by non-MR FW owner does not show as "locked" when place behind Mercury OEM controller(DCSG01058849
 7.21: A hang is seen when attempting to update the the psoc using a catalog file when storcli does not support, but FW does.(DCSG01093791
 AeroMR_7.20PA:Storcli Hangs on triggering controller restart and fails to exit command prompt(DCSG01040153
 MR719_PA1_MA drive become jbod(Unsupported) and IO will run on them(DCSG00957470
 PD state change reported only once when copyback is suspended and resumed(DCSG01081139
 Hot add drive on UBM backplane with x2 or X4 DFC reports incorrect element status in SES Page 02h(DCSG00967012
 MR7.20-iMR-Multi-LUN / Multi-Actuator drives show up as good(DCSG01024028
 Fix response to setting JBOD for unsupported drive(DCSG01041383
 [Aero] PCIe Compliance Configuration Failure - 1_44 DPA Ext Cap Struct(DCSG00972342
 ScrutinyCLI in UEFI mode failed to download Aero MR NOPAD images using hostboot (hb) command(DCSG00984134
 BST Failure: Revert defect 1010648(DCSG01021874
 Update BinToRom.exe to match updated BinToRom.c(DCSG01082490
 Added "TimeSyncInterval" to the FW ManPage11 data-struct to match the XSD definition(DCSG01041327
 MR_7.20:VD target IDs changing during foreign config import - DC observed on running IOs post VD import(DCSG01045309
 FW Fault 2622 observed during system boot up in some new Gen4/Gen5 servers(DCSG00947451
 FW not setting Opal MSID password length properly when resetting password to MSID(DCSG01042567
 Remove deprecated Vision builder(DCSG01078124
 MR7.20-Discrete part iMR controller allows PSOC flashing(DCSG01066232
 RefClk enabled for sgpio backplane type(DCSG00995519
 NVMe response buffer differs from host for get smart health information(DCSG01118222
 Firmware asserts during OCR with JBOD auto creation(DCSG01074021
 Fix Missing OCP ROMs Copy Back(DCSG01093193
 VPD data printed on every reboot(DCSG01035788
 MR 7.18: Secure drives creation using multiple secure key unable view and import the first removed encrypted VD until the second VD has been imported.(DCSG00924602
 VD Failure while updating Drives(DCSG01116221
 Integrate IT Security Page Fixes into MR(DCSG01030957
 Update Version Field value in Std Inquiry Data of vSES Device(DCSG00966397
 BST Failure: Update ManPage11 for Phase 21 PL(DCSG01027882
 Fix to handle TTY Flash with write error(DCSG01077025
 MR 7.20: Json Event long message for missing PD needs to be updated(DCSG01040031
 Phy bad events seen for one of the Enclosure Valid Slot(DCSG01088807
 Fix too many debug messages(DCSG01032533
 Data Abort exception happened during journaled writes(DCSG01113159
 Fix EPD boot disk not available at legacy BIOS(DCSG01111179
 (SATA Only) Inquiry command to read Block device Characteristics VPD Page fails on some SATA drives(DCSG01025293
 Two elements of SES Page A are assigned same slot number for UBM backplanes with x2 DFC(DCSG00966202
 Fatal firmware error detected after converted SATA SSD PD to JBOD(DCSG01112314
 Critical Error Log created if the Firmware Download of BIOS using BIOS image from different package than Firmware.(DCSG00951807
 Fix Delayed Expansion Issue in add_catalog_rom.bat(DCSG01092304
 Update the Default Vendor ID of Virtual SES Device(DCSG01012204
 Unsupported MPI Config page read from OOB provides data in response(DCSG00937617
 Drives not discovered when an enclosure is hot plugged after removing a PCIe switch based JBOF(DCSG00957168
 EPD is not created after import with escrow if escrow key matches controller key(DCSG00968394
 FW asserts when try to create secured VDs using a FDE drive(DCSG01138487
 Patrol read fails to correct medium error on verify capable NVME drives(DCSG01055287
 Fix unmap writesame for a NVMe drive with small max data buffer length(DCSG00972351
 SATA only : ATA PT command for SMART READ ATTRIBUTE THRESHOLDS(B0h/D1h) fail when COUNT field is set to 0(DCSG01030777
 Autoconfig fails to create R0 or EPD on eligible drives in presence of Multi-Lun drives.(DCSG01030203
 When read termlogs observing Copyright as 2017-2018 which needs to be changed to 2017-2021(DCSG00960207
 Data Miscompare observed with sliced R5 Logical Drives during write(cache) policy change(DCSG01161554
 Drive changes from UG to UB, when user start the initialization followed by secure erase on same drive(DCSG00837473 (Port Of Defect DCSG00946483)
 MR7.20: Found a lot prints "C0:MfgMsg: Error reading device chemistry. I2C Error = 0x2" while PR(DCSG01044765 (Port Of Defect DCSG01077927)
 Patrol read fails to correct medium error on verify capable NVME drives(DCSG01055287 (Port Of Defect DCSG01078110)
 Fixed fault 0xF000 when doing VSES task management(DCSG00927996 (Port Of Defect DCSG00934187)
 Boot message "Error restoring offloaded cache" popup for 940 card w/o SuperCap during AC power cycles(DCSG01087695 (Port Of Defect DCSG01116312)
 Connector name in SAS Device Page 0 of the VSes/DA-SEP is not set correctly(DCSG00995575 (Port Of Defect DCSG01003869)
 SPDM key reading failed when complete flash Erase case(DCSG01032600 (Port Of Defect DCSG01032601)
 Incorrect PLDM firmware release date is displayed in BMC applications(DCSG00926179 (Port Of Defect DCSG00966522)
 FW hits an ERROR: Exception Handler EXCEPTION during reboot of a server with PCIe gen5(DCSG01097640 (Port Of Defect DCSG01107907)
 Aero 7.19 iMR: CBB unable to find secondary image(DCSG00987835 (Port Of Defect DCSG01038387)
 BMU set startlearntime does not set properly(DCSG00917983 (Port Of Defect DCSG00991775)
 Fault 0xEE19 observed while running lane break test with managed switch attached to controller.(DCSG00939163 (Port Of Defect DCSG00947866)
 KeyID is cleared before the transition is finished(DCSG00936150 (Port Of Defect DCSG00977211)
 NVRAM signature invalid. Aborting DDR scrub & ECC check!!!(DCSG01111513 (Port Of Defect DCSG01126920)
 FW asserts when try to create secured VDs using a FDE drive(DCSG01138487 (Port Of Defect DCSG01148515)
 MCTP : MCTP MPI requests are failed with drive missing status even when drive is present(DCSG00952803 (Port Of Defect DCSG00956655)
 SATA : one or more HDD are not discovered by OS when drives behind expander are powered ON(DCSG00947126 (Port Of Defect DCSG00964427)
 7.21: A hang is seen when attempting to update the the psoc using a catalog file when storcli does not support, but FW does.(DCSG01093791 (Port Of Defect DCSG01099363)
 Incorrect slot number reported for drive with bad Phy(DCSG00986779 (Port Of Defect DCSG00989522)
 [3408+ MR7.16] configurablePDCount would exceeded if set jbod on while UG drives are in spundown.(DCSG01032834 (Port Of Defect DCSG01044605)
 Bad sensor slot case should not counted again when marking slot bad.(DCSG00961696 (Port Of Defect DCSG00977229)
 SATA drive is not detected during hot plug test(DCSG00975159 (Port Of Defect DCSG01062363)
 NOTIFY(ENABLE SPINUP) is not sent to spin up legacy SAS drives when partial/slumber mode is enabled.(DCSG01044213 (Port Of Defect DCSG01137571)
 VD Failure while updating Drives(DCSG01116221 (Port Of Defect DCSG01124651)
 DMA error observed during xtools 'show' command in Atlas behind Aero config(DCSG01051896 (Port Of Defect DCSG01079552)
 NVME EPDs, with heavy IOs and TM from host side and NVMe passthru commands in loop from OOB. After 5-8 hrs hit KA(DCSG00939439 (Port Of Defect DCSG00970531)
 Secure erase is allowed on JBOD/EPD(DCSG00840773 (Port Of Defect DCSG00970537)
 Some drives missing in OS when Direct attached slot order event replay flag is set in NVDATA(DCSG00991409 (Port Of Defect DCSG00996085)
 Log Power State Change event for Hot spare drives spun up using MR_DCMD_PD_POWER_STATE_SET DCMD(DCSG01137533 (Port Of Defect DCSG01138265)
 Firmware asserts during OCR with JBOD auto creation(DCSG01074021 (Port Of Defect DCSG01091678)
 FW Logs/termlogs should change the Copyright 2017-2022(DCSG01116760 (Port Of Defect DCSG01119586)
 FW hits an ERROR: Exception Handler EXCEPTION during reboot of a server with PCIe gen5(DCSG01097640 (Port Of Defect DCSG01107908)
 MR_7.20 missing VD's after OCR and enclosure Pull/Push(DCSG01061674 (Port Of Defect DCSG01074900)
 Fix LSA time sync problem(DCSG01029543 (Port Of Defect DCSG01034066)
 PCIE failure causes TBM failure which leads to control plane hang(DCSG00969750 (Port Of Defect DCSG00990809)
 Incorrect usage of Block Limits Virtual physical disk npwg field resulting in 0x7 being treated as 7 512B sector length IOs with NVMe drives(DCSG01026871 (Port Of Defect DCSG01032306)
 Assertion failure in FW when user initiate rebuild on partial degraded R6 VD(DCSG00921397 (Port Of Defect DCSG00970530)
 Fault 0xEC0F seen while aborting an active recovery on a NVMe drive(DCSG01021656 (Port Of Defect DCSG01023749)
 FW stuck in COL-BIOS Reset loop when COL times out(DCSG00907382 (Port Of Defect DCSG00932410)
 MR7.20-Discrete part iMR controller allows PSOC flashing(DCSG01066232 (Port Of Defect DCSG01070280)
 CLI application shows improper error import message after successful Foreign import(DCSG00915940 (Port Of Defect DCSG00970535)
 MR7.20-Drive pull during recon-Assertion failure in fw\raid\pd.c at line 8254 AR Invalid(DCSG01054517 (Port Of Defect DCSG01066945)
 Kill adapter seen on multiple EPDs with IOs with TMs(DCSG00923995 (Port Of Defect DCSG00970534)
 Controller marks a drive UBUnsp if the server is rebooted while running Sanitize Overwrite(DCSG01141274 (Port Of Defect DCSG01165082)
 Clearing the tty history with cli delete termlog command causes firmware to hang(DCSG01098208 (Port Of Defect DCSG01108301)
	
EnhancementRequests:	
 Add Firmware Version 11 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01149460
 Update ControllerInfo Structure with PartNumber - API Changes(DCSG01064529
 ATA Passthrough handling of ATA commands(PIO DATA IN) obsolete in latest ATA specification for backward compatibility(DCSG00999763
 Connector Order change for 9502-16e controller(DCSG00966344
 Safestore: MegaRAID key management feature: temporary key escrow(DCSG00918486
 Clean up include files(DCSG00977963
 added new BST file for shenandoah(DCSG01108340
 PEX89000: Single host MPT BST support on Veloce(DCSG01024714
 Update XSDs with Proper Active High/Low Flags for GPIO_LED_GLOBAL_FAULT(DCSG01082422
 Block Multi-LUN / Multi-Actuator : SAS Device only Report as Unsupported Device(DCSG00907506
 Snapdump: Remove duplicate entry in additional battery statistics(DCSG00951438
 Reorder Snapdump files for reliability(DCSG01008677
 Add PSoC 6 FW to Catalog File(DCSG01107483
 SAS phy port configuration of UBM connected phys based on UBM DFC Link width.(DCSG00927212
 Add a tool for code coverage(DCSG01000074
 Improve python handling during code coverage builds (MR)(DCSG01040296
 PL SATL : Add SAT translation for the Concurrent Positioning Ranges VPD page(DCSG00927210
 Add Firmware Version 9 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01136458
 PEX89000:Use SDB to inject errors in Error Counter BST testcase(DCSG01079551
 Create offload expected status field in NVSRAM(DCSG01098154
 Remove the Standard IO Header from cache offload module(DCSG00985595
 SRAM layout changes for code coverage(DCSG01026846
 Release Automation: automate rebase operation for phase specific streams(DCSG00950531
 UBM error handling improvements and debug statistics data collection(DCSG00903198
 Add Firmware Version 6 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01126019
 Update linker script file for mbed TLS component(DCSG00966563
 Add code coverage configuration(DCSG01005808
 Update SAS 3.5 FW summary release notes(DCSG00979878
 Add Firmware Version 3 for PartNumber 29211 to PSoC Catalog Image(DCSG01116340
 Add Firmware Versions 27 and 1 for PartNumbers 15987 and 25731 to PSoC Catalog Image(DCSG01166118
 Remove old MCTP OEM-conditional code(DCSG01016044
 Spell Checking Corrections Part 6(DCSG00963337
 DRAM layout changes for code coverage(DCSG01010648
 Add Interposer PSoC 6 FW to Catalog File(DCSG01121802
 Dump code coverage counters for Ondemand Snapdump(DCSG01020724
 Add Code Coverage infrastructure(DCSG00981200
 Remove some whitespace from the config page firmware(DCSG00968465
 Check in the build system's supporting function that can checks print statement consistency(DCSG00977490
 Add Lmid/Smid local/host mem dump into SD(DCSG00289727
 Add partial xml for 9502-16i Controller OCP form factor(DCSG00961958
 Integrate SPILIB 2.0 into MR Firmware for Aero, Sea and Ventura(DCSG00040487
 Release Automation: Assign release type when creating ROP(DCSG00941419
 [Aero] Enable UBM detection logic on all connectors for OEM HBA with SEP_PRESENT GPIOs(DCSG00927207
 Improve code coverage statement counting near prints(DCSG01031751
 Add control command MFI_OOB_MCTP_CONTROL_EXCEPTION_NO_CMD (0x99) in API(DCSG01065378
 Add Vision sources to cpld_src(DCSG01082289
 Add Firmware Version 7 for PartNumber 29211 to PSoC Catalog Image(DCSG01128627
 [UBM] Add detection of SAS/SATA drive with UBM backplane supporting IFDET2# and PRSNT#(DCSG00945423
 Add Firmware Version 5 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01123516
 Add 9502-16e board Nvdata to Aero ROP(DCSG00966467
 Update BinToRom for Multiple PSoC Images(DCSG01063758
 Release Automation: Update scripts for FW Ph21(DCSG01008758
 Reorder Snapdump data collection for reliability(DCSG00991989
 Add NVDATA option to change DMA Activate FIS timeout value.(DCSG00952761
 Update PSoC Bootloader Design in MR FW for PSoC 6(DCSG01107508
 Snapdump Enhacement - SES Module(DCSG00952775
 MR SAS Multipath Improvements(DCSG00956036
 Update PSoC MR FW Downgrade Block MFI_STAT to be More Clear(DCSG01155856
 Release Automation: Check for failure during baseline creation(DCSG00958012
 Add Reboot logs for windows Cache Offload BST(DCSG01074472
 PEX89000: Veloce Cosim Dev BST framework(DCSG01001901
 Atlas2 BST ER: PCIE and SysDMA feature BST Evaluation for COSIM(DCSG01006212
 Snapdump improvement - dump NVRAM key info(DCSG00951413
 Support flash usage above 4 MB(DCSG01006737
 Add OEM build action to SCONS(DCSG00996371
 Remove SASPARSER binary from Release Order(DCSG00957868
 Clean up inline functions(DCSG00984425
 Add Firmware Version 10 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01136459
 Add Firmware Version 12 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01159010
 Add Firmware Version 8 for PartNumbers 29211 and 29651 to PSoC Catalog Image(DCSG01130658
 FDE logging improvement: consolidate VKI_PRINTF(DCSG00904945
 Dump code coverage counters on controller reset(DCSG01005809
 Create adjusted code coverage reports(DCSG01050388
 MegaAPI_PVT: Move VPD get DCMD from private to public API to Enable end user tools to read custom SN(DCSG00950711
 Improve python handling during code coverage builds (fw_bld_tools)(DCSG01040300
 Code Space Optimization(DCSG01017044
 Atlas2 BST ER: Multi host flash boot: create synthetic hierarchy and basic EP and config traffic(DCSG01021605
 PEX89000:Veloce Cosim Dev BST error counter testcase(DCSG01006209
 secureSignBin: implement feature to download the public key during signing or with explicit arg(DCSG01035866
(DCSG01082488
 Enhance out of order insertion feature to support R1 & R10(DCSG00903546
 PL SATA : Read logpage 12 and 13 during SATA initialization to get features supported for NCQ encapsulation using FIS porting(DCSG00779724
 Improve a print error message in traceTool.py(DCSG00945787
 Move to the latest mbed_tls version which is 2.26.0(DCSG00966339
 Remove allocation of PCIe devices when NVMe is disabled in NVDATA(DCSG01015478
 PEX89000: Update Cosim DevBST framework to support launching simulation from outside user shadows(DCSG01093267
 SPILIB2: Port all changes AV1 to AV2 for manual access files(DCSG00917802
 Add PERC Signing Build Targets to fwSConstruct(DCSG01071385
 Add Scons checking for code coverage(DCSG01026819
 Support streaming of debug logs (HTB) via I2C OOB band on Ventura/Aero IOC/HBA (Part B)(DCSG00927213
 LD Secure Erase and Progress Reporting(DCSG00931395
 PEX89000: Update BST framework for Linux host and other enhancements(DCSG01062557
 Add Atlas2 A0 devBST for automatic CQ launch(DCSG01003423
 SPILIB: Update build scripts for ADS(DCSG00943761
 Reintroduces the previous security page as MR_MPI26_CONFIG_PAGE_SECURITY_1 to align with current NVDATA(DCSG00977495
 Extending SnapDump Persistence(DCSG00247000 (Port Of EnhancementRequest DCSG00966519)
 Enable DASEP detection on SASA for Adapters(DCSG00983302 (Port Of EnhancementRequest DCSG01071382)
 Bad Phy detection logic improvement(DCSG00932841 (Port Of EnhancementRequest DCSG00977228)
 Error handling of UBM CHANGE_DETECT# signal(DCSG00962565 (Port Of EnhancementRequest DCSG00963253)
 Do not generate "Bad Phy" event for NVMe drives that fail NVMe Init(DCSG00543046 (Port Of EnhancementRequest DCSG01070337)
 Update ControllerInfo Structure with PartNumber(DCSG01063757 (Port Of EnhancementRequest DCSG01074470)
 Disk labels need to be tied to fixed physical ports in order(DCSG00240927 (Port Of EnhancementRequest DCSG00966521)
 Enable DASEP detection on SASA for Adapters(DCSG00983302 (Port Of EnhancementRequest DCSG00990994)
 MR FW Need a smooth and authenticated method to transition from LKM to EKMS (SEKM)(DCSG00318546 (Port Of EnhancementRequest DCSG00432105)
 Passthrough Support for Vendor Specific NVMe Opcode D9h and C0h(DCSG01128891 (Port Of EnhancementRequest DCSG01151746)
 Create new profile with only SAS/SATA drive support for new controllers for DASEP backplanes(DCSG00991280 (Port Of EnhancementRequest DCSG01070765)
 Remove Retries When INQUIRY for Extended VPD Page 86h Returns 5/24/00(DCSG00922081 (Port Of EnhancementRequest DCSG00966515)
 NVMe Passthru command support(DCSG00432879 (Port Of EnhancementRequest DCSG00966518)
 Add PSoC Image Checking and MR FW Blocking(DCSG01064530 (Port Of EnhancementRequest DCSG01074471)
 Enhance Error scenario handling in SEKM Feature code(DCSG00966411 (Port Of EnhancementRequest DCSG00974796)
 Create new profile with only SAS/SATA drive support for new controllers for DASEP backplanes(DCSG00991280 (Port Of EnhancementRequest DCSG01069429)
 Update and Add PSoC Image Building Batch Files(DCSG01063756 (Port Of EnhancementRequest DCSG01074467)
 Do not generate "Bad Phy" event for NVMe drives that fail NVMe Init(DCSG00543046 (Port Of EnhancementRequest DCSG01070769)
 LKM compliance to Cryptographic Algorithm Requirements v1.5(DCSG00830702 (Port Of EnhancementRequest DCSG00966516)
 Sea iMR CBB Updates(DCSG00980247 (Port Of EnhancementRequest DCSG01032931)


Version 52.19.0-4165 - Moderate Impact/Low Probability of Occurrence
-------------------
    BIOS:7.19.00.0
	UEFI Driver:0x07130200
	HII: 07.19.04.00
	IMR FW: 5.190.01-3553
    package 52.19.0-4165




Lenovo Data Center Group Linux OS Support Home Page
linux.lenovo.com

© 2018-2024 Lenovo. All rights reserved