Lenovo YUM Repository
Release and Change History
Lenovo YUM Repository
Release and Change History
| Bundle Release Information: |
| Targeted Server Family (Machine Type): Lenovo ThinkSystem SR655 (7Y00, 7Z01) |
| Targeted Operating System: SLES12SP5 |
| YUM Repository Build Date: 2025_10_21 |
| Device: |
| ThinkSystem Intel X710-T2L 10GBASE-T 2-port OCP Ethernet Adapter | Part Number: 4XC7A08278 Feature Code: AUZW |
||||
|---|---|---|---|---|---|
| PCIe Sub Vendor ID: 0x8086 PCIe Sub Device ID: 0x000F |
| Release History: |
| Release Change History Documents |
===========================================================================
Intel v30.1 Network FW Update Release for Linux
Release date = 06/05/2025
Package Version: net-9.52-6.50-1.3818.0-0
===========================================================================
CONTENTS
________
1.0 Change history
2.0 Web information and support phone Number
3.0 Notices and trademarks
4.0 Disclaimer
1.0 Change history
___________________
This release includes the following updates:
============================================
Versions:
1) The following X710/XXV710 images are at NVM 9.52 level.
------------------------------------------------------------------------------------------------
Device Boot ROM (Option ROM) Firmware (Etrack ID)
------------------------------------------------------------------------------------------------
ThinkSystem X710-T2L PCIe 1.3684.0 8000F6DF
ThinkSystem X710-T2L OCP 1.3684.0 8000F61E
ThinkSystem X710-T4L PCIe 1.3684.0 8000F6DE
ThinkSystem X710-T4L OCP 1.3684.0 8000F6DC
ThinkSystem X710-T2L OCP (Interlock) 1.3684.0 8000F6DD
System x and ThinkSystem X710-DA2 1.3684.0 8000F629
ThinkSystem X710-T4 1.3684.0 8000F62C
ThinkSystem X710-DA4 1.3684.0 8000F62B
ThinkSystem XXV710-DA2 1.3684.0 8000F62A
The following X722 images are at NVM 6.50 level.
---------------------------------------------------------------------------------------------------------
Device Boot ROM (Option ROM) Firmware (Etrack ID)
---------------------------------------------------------------------------------------------------------
ThinkSystem SR530/SR550/SR570/SR590 X722 1.3818.0 80004398
ThinkAgile SR530/SR550 X722 LOM 1.3818.0 80004398
ThinkSystem ST550 X722 LOM 1.3818.0 80004399
ThinkAgile ST550 X722 LOM 1.3818.0 80004399
ThinkSystem SR630/SR650/SR850/SR950 X722 LOM 1.3818.0 8000439C
ThinkAgile HX and VX Rack servers X722 LOM 1.3818.0 8000439C
ThinkSystem SN550/SN850 X722 LOM 1.3818.0 8000439A
ThinkAgile SN550/SN850 X722 LOM 1.3818.0 8000439A
ThinkSystem SD650 X722 LOM 1.3818.0 8000439B
ThinkAgile DS650 LOM 1.3818.0 8000439B
ThinkSystem SE350 X722 LOM 1.3818.0 8000439E
The following X710 images are at NVM 9.20 level.
------------------------------------------------------------------------------------------------
Device Boot ROM (Option ROM) Firmware (Etrack ID)
------------------------------------------------------------------------------------------------
X710-DA2 ML2 1.3357.0 8000DEE5
The following X550 images are at NVM 3.60 level.
------------------------------------------------------------------------------------------------
Device Boot ROM (Option ROM) Firmware (Etrack ID)
------------------------------------------------------------------------------------------------
Intel X550-T1 1.3141.0 80001745
Intel X550-T2 1.3141.0 80001746
The following adapters are ONLY for Option ROM
------------------------------------------------------------------------------------------------
Device Boot ROM (Option ROM) Firmware (Etrack ID)
------------------------------------------------------------------------------------------------
I350 1.3450.0 NA
I210 1.3450.0 NA
2) NVMUPDATE tool updated to 1.43.8.0 to support new config version.
This update supports Lenovo ThinkSystem and ThinkAgile products, except DS530.
Important Note: If you choose to install the nvmupdate64e utility manually, please ensure that you install
version 1.43.8.0 or newer.
Earlier versions of nvmupdate64e tool may not be not compatible or include all latest supported features.
New OS Support:
- Support RHEL 9.5/9.6
- Support RHEL 10.0
FVL/SGVL
-------------
Bug fixes:
- IPS: 00876990 - Intel X710-T4L 10GBASE-T 4-Port OCP Ethernet Adapter
failed to wake up in Windows server 2022.
Description:
In windows OS, BIOS enable WOL, when we set PME to Disable,
the WOL function will not work anymore, even we turn it back to enable.
Fix:
Remove code check for PFPM_APM for a WoL supported port.
- IPS: 00914122 - Some ports on the Intel x710-T4L PCIe negotiate to 100Mb
on reboot from OS RHEL8.8.
Description:
X710-T4L PCI adapte sometimes linked up at 100Mb on RHEL 8.8
when the link partner was Lenovo NE1032T switch.
Fix:
Restores old behaviour While continuing to ensure that D3hot is reached
and WoL is disabled when NVM update requires a full shutdown.
- IPS: 00936091 - Intel firmware update does not support inbox Linux driver For 700 series.
Description:
Intel firmware update does not support inbox Linux driver. Given this,
the Intel firmware update tool needs to detect the inbox driver then
fail gracefully with a message about the OOB driver requirement.
Fix:
Add SUPS script to require install OOT driver.
- IPS: 00934339 - SR630 x722 4x10Gb SFP+ link down when 1 port connected to Cisco C93180YC-FX3.
Description:
When 1 port of the X722 4x10Gb SFP+ is connected to the Cisco switch, all LEDs on the x722 PHY
card flash continuously. If we connect the X722 in pairs using 1&4 or 2&3 we do not see the failure.
Fix:
Adapt the original hotfix once made for FPK5.60 to FPK6.50 and force the OCP PnP Autodetection
flow after NVM update.
Release net-9.52-6.50-1.3684.0-4 includes the following updates:
=================================================================
New OS Support:
- Support RHEL8.10/9.4
- Support SLES 15.6
FVL/SGVL
--------
Bug fixes:
- PATCH request with request to change FlowControlConfiguration property
returns success, but do not really apply changes.
- LLDP receive property preserves the last received data, even when LLDP
traffic doesn't contain the TLV item/data.
- NetworkDeviceFunction schema Ethernet. The MACAddress property is not
updated to the value in PATCH JSON. This is a regression. The issue is
under investigation.
- PATCH request with request to to change FlowControlConfiguration
property returns success, but do not really apply changes. The issue is
under investigation.
- Fixed an issue where X710DA2 cannot get SFF temperature when another
port is empty.
Release net-9.50-6.50-1.3616.0-10 includes the following updates:
=================================================================
New OS Support:
- Support RHEL8.9/9.3
FVL/SGVL
--------
New features:
- Enable E700 X722 Tx signal to "always on".
- Enable E700 to store events details on the NVM in Recovery Mode.When
entering the Recovery Mode, X710 will store the details of the event in
the NVM.
Bug fixes:
- Resolved an issue where POST to the
NetworkAdapter.ResetSettingsToDefault looked successful from postman,
but after reboot the adapter's Port 1 LLDP setting did not reset to
default.
- Previously, there were cases of Fortville disappearing from the PCIe
bus during reboot stress testing reported on Icelake-based platforms.
These platforms performed a PCIe Hot Reset before asserting PERST# as
part of the warm reboot cycle. PERST# is asserted at approximately the
end of the Hot Reset, but due mostly to the Fortville LCB
implementation, there was a variation in the relative timing of about
65 us, so many edge cases could occur.
- Previously, after configuring "ifconfig ethX down" command on Marvell
devices series 88E1512/88E1514, the peer side (loopback configuration)
was still reporting link up.
- Fixed an issue. Unexpected EMP Reset occurred in a rarely BMC request
combination in a very low probability, which may cause: 'tx_timeout' or
'ARQ: Unknown event 0x0000 ignored' or 'bond down' if bonding is
configured.
- IPS: 00879846 - Intel XXV710-DA2 PCIe 25Gb 2-Port SFP28 Adapter link
speed and status incorrect
Description:
Link event is reported only once at when the machine is powered on,
after that no link event will be generated any more even after the
network cable is inserted and removed, this is incorrect, link event
should be reported when we plugin or remove the AOC cable.
Fix:
Firmware reported link speed value based on advertised capability value
using DNL declaration, changes to read link speed from MAC
- IPS: 00852370 - IEPD Hot Issue: SR645v3 X710 T2L PCIe bandwidth degraded
Description:
X710 PCIe may enter x1 on the AMD Genoa platform in reboot and AC
process.
Customer updated system firmware XCC: KAX318V >> KAX322V UEFI: KAE112O
>> KAE116K Following event occurs intermittently, but high fail rate
PCIe Link Width has degraded from x8 to x1 in physical slot number 3.
Slot 3 is Intel X710-T2L 10GBASE-T 2-Port PCIe Ethernet Adapter,
customer had tried new NIC FW, replace NIC but no help. this system no
re-timer.
Fix:
The firmware changes to enter the PCIE detection phase when PERST
becomes de-asserted
Release net-9.30-6.20-1.3450.0-10 includes the following updates:
=================================================================
New OS Support:
- Support RHEL8.8/9.2, SLES 15.5
FVL/SGVL
--------
New features:
- Get Link Status AQC response when SFP module is not initialized.
Description:
If the Get Link Status AQC is sent when the SFP module is not
initialized yet, the link can be lost.
When the SFP module is not initialized yet, FW will try again in a
reasonable timeout.
Bug fixes:
- IPS: 00819239 - [Kahauale_BBFV_HCT]X710-T4L NIC adapter can't saved the
"Active Physical Functions" option on uEFI menu.
IPS: 00831264/00844425 - XXV710-DA2 PCIe Adapter NIC port didn't
disable after changed the "Active physical functions"
Description:
Intel XXV710-DA2 PCIe 25Gb 2-Port SFP28 Adapter NIC port didn't disable
after changed the "Active Physical" setting on uEFI menu.
Fix:
Reset the length of the PCIe Alt Autoload section during image
downgrade to a version earlier than FVL9.2
- IPS: 00840914 - [PA_IO Agile-Sprint202310_BDC_Storage_flex]SRIOV
enable/disable both can do SRIOV features
Description:
OS can still create SRIOV VFs when the adapter HII already disables SRIOV
in the BIOS
IPS: 00841528 - [PA_IO Agile-Sprint202310_BDC_Storage_SD530] Intel X722
LOM test SR-IOV function cannot enable VF under ESXi8.0u2 OS
Description:
Open to enter ESXi Host Client-Manage-Hardware-PCI Devices-Select Port
"Intel X722 10GB SFP+" Configure SR-IOV 2.UEFI has set SR-IOV function
3.ESXi8.0u2 Unable to enable VF redhat 9.2 can work well.
Fix:
Correctly set SR-IOV Control Capable bit for Lenovo images,
- IPS: 00839473 - [PA_IO Agile-Sprint202209_BDC_oceancat_Sprint202310]X722
lom WOL fail in SD650.
Description:
WOL function UEIF page show gray, OS can not enable WOL function
Fix:
Enable force link down requests and map channel number in a descending
order. Enable AltRAM implementation then reset corrupted memory block and
recalculate MSI_X VF vectors.
- IPS: 00831248 - XXV710 VPD info question
Description:
lspci -s BUS:Device.Function -vvv command to check VPD info, but it
can't show out the VPD info
Fix:
Enable VPD bit in NVM image
- IPS: 00769725 - [Hakuba] Abnormal cable plug (unplug) event on port 2
and 3 with Intel X710-T4L
Description:
Port2 and port3 of X710-T4L PCIE cannot display event in audit log and
link status/speed in inventory when plug/unplug the cable.
Fix:
There are missing MCTP link status changes as mixed PF no. with port
no. in the MCTP Link Status change handler, and overflowing PLDM queue
with RDE events that were classified as Big Event.
Map Port No. to the corresponding PF and continue, add additional
condition to disable unplanned eventReceiver physical address change.
Disable RDE events in the presence of asynchronous MCTP implementation
without polling for Big Events
Note: it may still occur in loopback mode.
- IPS: 00725539 - Link down on x722 4x10Gb SFP+ PHY card with 27.3 code
level (800039xx)
Description:
After upgrading the FW, all ports are down.
Fix:
Force OCP PnP Autodetection flow after NVM update.
- Resolved an issue where a rare PCI speed degradation with Gen3 to Gen2
was seen during extensive link tests after a reset is caused by a core
reset on an ICX-D platform.
- Resolved an issue where during a write, with http PATCH method
triggered, the LLDP Disable Valid bit was ignored, which resulted in a
skip of write in all scenarios instead of just for the same LLLDP
Enabled value.
- Resolved an issue where if BMC bonding was disabled, NCSI mode was set
to a Manual Switch Mode (depending on the platform), and BMC share port
has changed before doing a power cycle, recovery mode would occur.
Other prerequisites include disabled WOL, disabled LLDP, enabled PXE no
drop, and disabled auto power-on after power loss (in BIOS).
- Fixed an issue where the processing port id was always the same as the
mac address
- Previously, the addition of PCIe re-timers added to the total channel
latency causing replay timer timeout correctable errors.
- Resolved an issue where PLDM type MCTP packets were not accepted due to
missing configuration for PCIe VDM
I350/210
------------
New features:
- IPS: 00699338 - Name of I350 interlock in XCC is inconsistent with V1
Description:
Card Name field shall be taken from V1 VPD field instead of "large
resource string". This change applies to 1G Lenovo devices with enabled
AIM support and existing V1 VPD field.
Release net-9.2-6.2-1.3357.0-2 includes the following updates:
==============================================================
New features:
- Defines the IID (Instance IDs) field in the NC-SI packet's header,
which is used to match responses to requests and to differentiate
between new and retried commands.
Description:
According to the spec, If the IID of the current command is the same as
the previous command's IID, the command is a "Retried Command" and the
FW shall return the response of previous command (should be done
without re-executing the command). When the IID is different than from
the previous command, the command is executed.
The NC-SI spec is unclear on if the incoming commands IID is compared
to the IID of the previous command received on the same channel,
package or device. This feature defines a transfer to maintaining a
single buffer for the last NC-SI command received on the device per
transmitting interface.
Bug fixes:
- XXV710DA2 adapter intermittently lose link when doing DC power cycle test
Description:
XXV710DA2 adapter intermittently lose link when doing DC power cycle
test, this can be reproduced in about 200 DC cycle.
Fix:
When the FW starts to run, the gearbox has to be initialized and
configuration needs to be downloaded from the NVM and applied. If one
of the operation fails the FW will try again (several times). In this
case the configuration failed with the error which was not covered.
Error handling extended in the code to cover all cases
- Package Port Control command with Port Control equals 0x1 works like
reset if link is already up
Description:
In Campbell Pond, send Package Port Control Command to disable the
port, send command to enable it, then send command to enable it again.
The port is down instead of up.
Fix:
Added link status check in package command.
- Link Status Change AEN event is not send after link down
Description:
Sending AEN Enable command with Link Status Change equals true, then
sending Port Control Command with Port Control field equals 0x0 -
disable. There is no event after link down.
Fix:
Changed event rejection condition to response.
- After running reboot 123 times with qtest, slot4 (X710-T2L) shows an error
Description:
Used qtest ro run reboot 123 times, xcc web appears: PCIe Correctable
Error Threshold limit has been exceeded at Segment 0x0000 Bus 0xA8
Device 0x00 Function 0x01.
Fix:
Adjust the replay timer timeout value for different scenarios.
Note on Firmware Recovery Mode:
When a device is in Firmware Recovery mode it will not pass traffic or allow any configuration; you can only
attempt to recover the device's firmware. A device will enter Firmware Recovery mode if it detects a problem
that requires the firmware to be reprogrammed.
Resolving Firmware Recovery Mode Issues:
If your device is in Firmware Recovery mode you can restore it to factory defaults using the latest NVM
Update Package. Download the latest NVM Update Package from your vendor's support website and follow
the instructions in it.
*** NOTES:
- Before initiating device recovery, the integrity of the host operating system, device drivers
and firmware utilities must be verified and reinstalled if necessary. Fully functional operating
system, device drivers and tools are required for device recovery.
- AC power cycle your system even if the instructions do not indicate that an AC power cycle is required.
A power cycle is required to enable the device to restore and reload critical device settings to enable recovery.
To perform an AC power cycle, do the following:
a. Shut down the system if it is powered up.
b. Unplug all AC power cords from the system.
c. Leave the AC power cords unplugged for 15 seconds to allow the system power supply to discharge completely.
d. Plug in AC power cords to the system.
- Firmware Recovery Mode Errors and Messages:
When a device is in Firmware Recovery mode, the device drivers and preboot software and utilities may log or
display messages such as the following:
a. Firmware recovery mode detected. Limiting functionality.
Refer to the Intel(R) Ethernet Adapters and Devices User Guide for details on firmware recovery mode.
b. Firmware recovery mode detected. Initialization failed.
c. Firmware recovery mode detected. Limiting functionality.
d. PXE-E0C: Firmware recovery mode detected. Initialization failed.
2.0 Web Sites and Support Phone Number
______________________________________
o You can download new and updated files for Lenovo products from the Lenovo
Web site:
http://datacentersupport.lenovo.com/
o With the original purchase of an Lenovo hardware product, you have access to
extensive support coverage. During the Lenovo hardware product warranty
period, you may call the Lenovo HelpCenter for hardware product assistance
covered under the terms of the Lenovo hardware warranty.
3.0 Trademarks and Notices
__________________________
Lenovo is a registered trademark of Lenovo Corporation in the United States
and other countries.
Intel is a registered trademark of Intel Corporation in the United States
and other countries.
Linux is a registered trademark of Linus Torvalds in the United States and
other countries.
Other company, product, and service names may be trademarks or service marks
of others.
4.0 Disclaimer
______________
THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.
Lenovo DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS
FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE
INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, Lenovo
GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS.
Note to U.S. Government Users -- Documentation related to
restricted rights -- Use, duplication or disclosure is subject
to restrictions set forth in GSA ADP Schedule Contract with
Lenovo Corporation.
Lenovo Data Center Group Linux OS Support Home Page |
| linux.lenovo.com |
© 2018-2025 Lenovo. All rights reserved |
===============================================================================
Intel Linux device drivers package update
===============================================================================
Version [net-30.1-0]
===============================================================================
Driver Version
------ -------
ice 1.17.2
i40e 2.28.5
ixgbe 6.1.3
igb 5.19.2
irdma 1.17.31
iavf 4.13.5
ixgbevf 5.1.2
ice:
----
- Add documentation about PHY registers and FEC stats read
- Add freerun_filter ethtool flag
- Add sysfs file for SMA pin control
- Add E825 device to readme
- Fix reducing loglevel to debug for 'Can't delete DSCP' message
- Fix size of the passed buffer to ice_migration_save_devstate
- Fix possible OOB access in ice_vf_vsi_dis_single_txq
- Fix SMA sysfs store and U.FL names
- Fix devlink register on older kernels
- Fix param validation in get_q_vector
- Fix error message for insufficient filter space
- Fix ice_capture_crosststamp on kernels 6.11+
- Fix ice_adapter build without CONFIG_PCI_IOV
- Fix for missing OPT_PHY_TYPE bits in ACC_AOC_AUI adapters
- Fix ice_health_deinit() order
- Fix enabling DPLL only for E810 ethernet adapter
- Fix E82X timestamping not supported
- Fix missing 50G ethtool mappings
- Fix updating Get Tx Topology AQ command read flag
- Fix fwlog after driver reinit
- Fix tc iteration in ice_vc_cfg_qs_msg()
- Fix Get Tx Topology AQ command error on E830
- Fix possible out of bound access in ADQ map_q_vector
- Fix validation of virtchnl msg in irq map msg
- Fix setting default Rx VSI twice in switchdev setup
- Fix ix deinitializing VF in error path
- Fix SLES15sp7 beta3 compilation
i40e:
----
- Add 8086:15ff:108e 0000 branding string
- Fix Error I40E_AQ_RC_ENOSPC adding RX filters on VF
- Fix MACVLAN filters leak by adding lock/unlock around functions calls
- Fix kernel 6.11 compilation error
- Fix compilation with gcc14
- Fix UBSAN "index 1 out of range for type 'u32 [1]' complain"
- Fix XDP program unloading while removing the driver
- Tested under RHEL 9.5
ixgbe:
----
- Add support for NVM update during FW recovery
- Add support for ACPI WOL for E610
- Add E610 .set_phys_id() callback implementation
- Add xarray into kcompat for old kernels
- Add documentation for E610 FW Logs
- Fix out-of-bounds access by using proper bit constants for EEE
- Fix remove 128 CPUs limit for XDP
- Fix stop setting carrier on while the adapter is down
- Fix use netdev->fcoe_mtu when required
- Fix .ndo_fdb_add() signature for kernel 6.13
- Fix SLES15sp7 beta3 compilation
- Fix unused variable warning
- Add baisc support for E610 cards
- Fix kernel 6.11 compilation error
- Fix potential NULL adapter->vfinfo dereferencing
- Fix incorrect kdoc
===============================================================================
Intel Linux device drivers package update
===============================================================================
Version [net-29.3-10]
===============================================================================
Driver Version
------ -------
ice 1.15.4
i40e 2.26.6
ixgbe 5.21.5
igb 5.17.4
irdma 1.15.12
ice:
----
- Introduced ICE driver migration for Linux DPLL interface usage in
kernel 6.7
- Devlink support for tools algorithm improvement
- Ethtool flow-type ether support
- add VF reset on Tx MDD event
- Message logs related to Health Status 0x110 updated
- Celo process may not be ended or killed while exiting application. As
the result current console is non responsive. Stability of the system
is not endangered and user can start next console session.
- Fixed adding VF to namespace and setting it to up status producing an
error in dmesg, VF now works normally.
- Fix bug with missing extts events
- Add automatic VF reset on Tx MDD events
Version [net-29.1-0]
===============================================================================
Driver Version
------ -------
ice 1.14.9
i40e 2.25.7
ixgbe 5.20.3
igb 5.16.3
irdma 1.14.17
ice:
----
- Add Switch Recipe resources reuse
- Support FW Debug Dump
- Support internal temperature reading
- Support RoCEv2 Active/Active LAG
- Add delay of SW initialization during PHY FW upload
- Add temperature sensor readouts
- Add "No FEC" mode to allow the LESM's "Auto FEC" mode to use "No FEC"
in link establishment process
- Add support of ethtool flow-type ether
- Rx timestamp functionality for VFs
- Traffic mirroring via tc-mirred
- FW debug logs support in debugfs
- Introduce flexible VF loopback pacing configuration to improve
VF-to-VF throughput
- Devlink health support for Tx hang debugging
- Add PHY statistics dump
- LLDP support on VF
- DMA_buf w/o ODP support for Linux RDMA
- Print NIC FW version
- Multicast promiscuous mode doesn't work after PF-to-VF reset.
- Fixed issue of unexpected FW logs during some special environments,
such as tx_timeout or NVM update.
- Ice driver doesn't work when link-down-on-close is on.
- Input/output error shown after "link-down-on-close" priv-flags enabled.
- NULL pointer dereference happens in the ICE out-of-tree ICE driver.
Determine if PF Reset is in progress before accessing the coalesce
settings.
- It was observed that in some cases the TC rule is not removed when
adapter works in the switchdev mode, what was caused by improper
algorithm of TC rule removal method.
- "Scalable IOV" help text in Device Level Configuration is not
expected.
- Traffic statistics reported by ice driver have been changed to also
include RDMA traffic.
- Out-of-tree drivers don't support XDP redirect on v6.3. Report XDP
functionality through XDP features flag.
- DVM mode is not configured in parser library for raw packet filter.
Align the DVM configuration between kernel driver and hardware/DDP.
- Ice driver misc interrupt not getting generated for a interface.
Re-enable timestamp at the end of the BH of the interrupt.
i40e:
-----
- Add PHY debug register dump
- Add mdd-auto-reset-vf private flag
- Add core reset trigger to ethtool
- Add restore default speed when changed module does not supports
current speed settings
- Add tracepoints for nvmupdate troubleshooting
- Add tracepoints for pci reset callbacks for troubleshooting
- Add support for reading Trace Buffer
- Add ability to reset vf for tx mdd event also
- Add trace events related to SFP module IOCTLs
- Fix 32bit FW gtime wrapping issue for nvmupdate
- Fix err -110 after DCB ETS configuration
- Fix i40e_setup_misc_vector() error handling
- Fix missing rtnl locking when setting up pf switch
- Fix accessing vsi->active_filters without holding lock
- Fix SW DCB configuration when ADQ is set
- Fix PTP pins verification
- Fix passing tainted expression to kzalloc()
- Fix error by one for traffic class number
- mq core affinity reset on interface link lost. Removes
irq_set_affinity_hint() calls to make driver honor user affinity
settings
- I40e driver report "vf may be used uninitialized in this function"
during make process.
irdma:
------
- Support CVL 4.50, FVL 9.50
- Support RoCEv2 Active/Active LAG
- dma_buf w/o ODP support
ixgbe:
------
- Fix waiting for flash completion ACK
- Fix debugfs directory double creation
- Fix terminate probing right after wrong API detected
- mq core affinity reset on interface link lost/link state. Remove
irq_set_affinity_hint() calls to make driver honor user affinity
settings
igb:
----
- Fix array size overrun
- Fix adjfreq compatibility
Version [net-28.2-2]
===============================================================================
Driver Version
------ -------
ice 1.12.7
i40e 2.23.17
ixgbe 5.19.6
igb 5.14.16
irdma 1.12.55
ice:
----
- Large VF support (up tp 256 Qs)
- User can reassign PF LUT for VF usage
- Devlink port split support
- Tx rate limit support
- Dynamic msi-x vector allocations to various device functions via
devlink API
- PTP fixes for Timestamp timeout error.
- Resolved an issue where when using certain DDP package versions,
802.1ad type VLANs might not be correctly enabled on SIOV or SR-IOV
interfaces.
- Resolved an issue where running traffic via Open vSwitch (when an
SR-IOV VF have specific ipv6 address assigned), works for 20min
(until the neighbor table is clean on the switch/router) then it
stops until IPv6 from VF is deleted.
- Previously, the Switchdev feature's VF to VF communication was not
functional in the ice driver versions 1.10.1.2, 1.10.1.2.2, and
1.11.14.
- Resolved an issue where the NVM update process would need Power On
Reset on PTP devices unless the user manually turned off PTP activity
before the NVM update process was started.
- Resolved an issue where a performance issue caused the GNSS write
commands to be delayed and not delivered until the next commands
appeared.
- Resolved an issue where modifying inner or outer VLAN offload caps
while the link is down might break communications when the link is
later brought back up.
- Resolved an issue for Linux ice driver v1.7.16+ on E810 four-port
SKUs where VF could not be created on certain high-core count
platform because PF had exhausted all the MSIX interrupts.
- Resolved an issue where repeatedly adding/deleting a VF from a
namespace while also repeatedly changing its trust mode status could
result in call trace after a significant number of iterations.
- Previously an issue existed in the IAVF driver where the VF couldn't
communicate on inner or outer VLANs if the number of rx queues was
modified after switching off VLAN offloads.
- Resolved an issue when spoofchk was turned on, the VF device driver
would have pending DMA allocations while it was released from the
device.
- Previously a UEFI PXE installation of Red Hat Enterprise Linux 8.4 on
a local disk resulted with the system failing to boot.
- Resolved an issue where auxiliary module conflicts would be reported
between i40e and ice during the generation and installation of Linux
rpm packages.
- Resolved an issue where "ethtool -L/G" made E810 link down.
i40e:
-----
- Add PHY debug register dump
- Add mdd-auto-reset-vf private flag
- Fix FW v8.15 double vlan issue
- Fix 32bit FW gtime wrapping issue for nvmupdate
- Fix err -110 after DCB ETS configuration
- Fix pointer dereference after free
- Fix i40e_setup_misc_vector() error handling
- Fix missing rtnl locking when setting up pf switch
- Fix accessing vsi->active_filters without holding lock
- Fix SW DCB configuration when ADQ is set
- Fix PTP pins verification
- Fix passing tainted expression to kzalloc()
- Fix error by one for traffic class number
- Fix compilation issue with gcc older than 5.0.0
irdma:
------
- Support CVL 4.30, FVL 9.30
- Add readable descriptions to the printed AE codes in irdma to help
with debug and provide a better insight on what is going on.
- Fix the fixed value for ret code, make a vchnl re-negotiation
ixgbe:
------
- Add xdp frags support to ndo_xdp_xmit
- Fix kernel compilation issue related to u64_stats_fetch_ begin/retry
igb:
----
- Fix bitmaps declarations
- Fix array size overrun
- Fix adjfreq compatibility
- Fix e1000_read_nvm() error handling
- Fix always true if condition
- Fix netif_napi_add compilation for igb
- Fix warnings about ignored return value
Lenovo Data Center Group Linux OS Support Home Page |
| linux.lenovo.com |
© 2018-2025 Lenovo. All rights reserved |
Release: 30.1 05/25/2025
============================
New OS Support:
- Support RHEL 9.5
- Support RHEL 9.6
- Support RHEL 10.0
New adapters:
- Intel E610-XT4 10GBASE-T 4-Port PCIe Ethernet Adapter
- Intel E610-XT4 10GBASE-T 4-Port OCP Ethernet Adapter
- Intel E610-XT2 10GBASE-T 2-Port OCP Ethernet Adapter
- Intel E610-IT4 1GBASE-T 4-port OCP Ethernet Adapter
E610
-------------
New features:
- Basic driver support.
- Tx Hang detection mechanism.
- Thermal sensor events support.
- FW logging support.
- FW API Version Compatibility.
- Debug Dump support.
- Recovery and Rollback mechanisms.
Bug fixes:
- IPS: 00913030 - The system hang at DXE INIT during POST when bios enabled E610.
Description:
After the bios image upgrade, the uefi bios took very long time to boot.
The undi.initialize took about 2 hours, and the server finally entered the OS.
Fix:
The PF driver cann't able to get ownership after immediate reboot triggered by the BMC.
Added clearing the ownership data (including timeout flags) to the PCI Reset flow.
- IPS: 00944368 - During AC cycle stress, the first 2 ports of the E610 4-port OCP adapter can't link up.
Description:
The issue reported that port 0 and port 1 of the E610-XT4 OCP/E610-IT4 OCP could not link up
after some AC power cycles.
Fix:
The root cause is LESM state machine ends up in unknown state and returns an error.
If Link FW detects such an error for selected port then such port will be reset
in the Link periodic task i.e. no more than 100ms later.
E810
-------------
New features:
- Add ethtool reset support
- Add ETF timestamp debug logging
Bug fixes:
- IPS: 00860421 - [Oahu_AU_SIT_MQT2]Run MQT2 test ,XCC report E810-DA4 OCP link
speed degraded from 16 GT/s to 8.0 GT/s.
Description:
XCC report E810-DA4 OCP link speed degraded from 16 GT/s to 8.0 GT/s after
Run MQT2 test
Fix:
Replaced "CVL_PCIE_ANALOG" v 2347.10A0.04D with
"CVL_PCIE_ANALOG_ENG_2347_010A_04E" v 000.000.000 inside EML PCIe Analog Module
- IPS: 00913030 - E810 Media Detection setting is not preserved during
firmware updates
Description:
The Intel E810 Media Detection setting is not preserved during an Intel E810
firmware upgrade. After each firmware upgrade the Media Detection setting
is set to "Disabled".
Fix:
- MEDIA_DETECTION_MODE=1 means strict mode.
- Removing OverrideEnable manipulation by switching LinkSpeedMethod to be
OverridePhyTypes related
- IPS: 00915231 - Intel E810 NIC port flaps during Windows boot up with ice 1.15.121.0 driver.
Description:
E810 adapter experienced a one-time link flap during OS boot.
Fix:
The Windows driver removes the enhancement so it tries to reset the link
during the initialization and consequently causes the link flap once.
- IPS: 00916160 - "Transmit Balancing" and "Virtualization Mode" options are missing from the UCM.
Description:
The EFI driver in CVL4.6 (EFI 4.2.97) didn't provide the
"transmit balancing" and "virtualization mode" settings to the Lenovo UCM.
Fix:
Duplicate OpCodes had been removed from Transmit Balancing and Virtualization Mode.
- IPS: 00961945 - There are many useless resource ID provide by E810 NIC firmware
Description:
There are many useless resource ID provide by E810 NIC firmware.
Lenovo found NetworkDeviceFunctionMetrics and PortMetrics have two many useless resource ids.
Fix:
Use special API to get number of PFs defined by topology (number of PFs depends on number of MACs).
- IPS: 00956338 - [PA_BHS_Andros_SDV_HW_SO]E810-DA2 OCP display multiple Function ID on xcc Inventory web.
Description:
When tested on SR630v4,the E810-XXVDA2 OCP with CVL4.8 NVM image lists multiple
Function IDs on xcc Inventory web
Fix:
Using the API that returns the max number of possible ports in current product (based on Netlist).
FVL/SGVL
-------------
Bug fixes:
- IPS: 00876990 - Intel X710-T4L 10GBASE-T 4-Port OCP Ethernet Adapter
failed to wake up in Windows server 2022.
Description:
In windows OS, BIOS enable WOL, when we set PME to Disable,
the WOL function will not work anymore, even we turn it back to enable.
Fix:
Remove code check for PFPM_APM for a WoL supported port.
- IPS: 00914122 - Some ports on the Intel x710-T4L PCIe negotiate to 100Mb
on reboot from OS RHEL8.8.
Description:
X710-T4L PCI adapte sometimes linked up at 100Mb on RHEL 8.8
when the link partner was Lenovo NE1032T switch.
Fix:
Restores old behaviour While continuing to ensure that D3hot is reached
and WoL is disabled when NVM update requires a full shutdown.
- IPS: 00936091 - Intel firmware update does not support inbox Linux driver For 700 series.
Description:
Intel firmware update does not support inbox Linux driver. Given this,
the Intel firmware update tool needs to detect the inbox driver then
fail gracefully with a message about the OOB driver requirement.
Fix:
Add SUPS script to require install OOT driver.
- IPS: 00934339 - SR630 x722 4x10Gb SFP+ link down when 1 port connected to Cisco C93180YC-FX3.
Description:
When 1 port of the X722 4x10Gb SFP+ is connected to the Cisco switch, all LEDs on the x722 PHY
card flash continuously. If we connect the X722 in pairs using 1&4 or 2&3 we do not see the failure.
Fix:
Adapt the original hotfix once made for FPK5.60 to FPK6.50 and force the OCP PnP Autodetection
flow after NVM update.
Release: 29.3 07/25/2024
============================
New OS Support:
- Support RHEL 8.10/9.4
- Support SLES 15.6
E810
-------------
New features:
- Disable Optical Module Laser when Link/Port is disabled
- GET_LLDP type command : get all ports LLDP information
- Disabling of port 0 (as long it’s not associated with PF 0).
- Use Rx Loss to detect cable disconnect from Module
- Expanding i2c write handling to enable 4 bytes
Bug fixes:
- IPS: 00860421 - [Oahu_AU_SIT_MQT2]Run MQT2 test ,XCC report E810-DA4
OCP link speed degraded from 16 GT/s to 8.0 GT/s.
Description:
XCC report E810-DA4 OCP link speed degraded from 16 GT/s to 8.0 GT/s when
run MQT2 test. The issue occurred after 5 times of AC power cycle.
Fix:
The target PCIe PHY firmware has optimized on Receiver equalization
recipe to handle low loss channel condition over PCIe training process.
- IPS: 00815616 - [Kahauale_BBFV_HCT]E810-DA4 NIC port didn't disable
after changed the "Active Physical" setting on uEFI menu.
Description:
Port 3 of the E810-xxvDA4 adapters was always enabled no matter
whatever "active physical functions" was set to. but the customer
expects to have port 3 disabled when "active physical functions" is
set to "PF0,PF1 and PF2", "PF0 and PF1" or "PF0 only"
Fix:
Change the setting of "Active Physical functions", and corresponding
help display text
- IPS: 00841566/00846731 - E810-DA4 adapter's device name doesn't display
as expected
Description:
The DA4 adapter's device name under UEFI setup is different from the
one in the UCM.
Fix:
The efi driver changes to display as the customer wants.
- RAMON specific workaround implemented in DreadnoughtLake scripts in
case of caui4 no FEC links, was modified being applied only when outer
phy is RAMON (and not Parkvale).
- The NetworkDeviceFunction.MTUSize property is changed to reflect the
current OS defaults before the user configures specific value.
- Fixed a rare timing issue of nc-si oem command: plug-out optics and
plug-in again, BMC can NOT get temperature by reason code 0x5089.
- Removed the need for EMPR after temperature fatal threshold is
exceeded.
- When link goes down, recovered clock switches to an incorrect
frequency, and the external DPLL shifts the system timing.
- FW incorrectly mapped NC-SI channels to Physical ports when responding
to the Intel OEM NC-SI command 0x26 (no other command affected).
- Unsupported SMBus write command caused HW to trigger improperly handled
FW behavior, which blocked subsequent SMBus writes other than MCTP.
- If user configured 1G and needs to go back to 10G, not able to do so.
- Fixed PTP Time Error to be under 5 ns when running PTP in Boundary Mode
between PF with PKVL PHY and PF w/o PKVL PHY.
FVL/SGVL
--------
Bug fixes:
- PATCH request with request to change FlowControlConfiguration property
returns success, but do not really apply changes.
- LLDP receive property preserves the last received data, even when LLDP
traffic doesn't contain the TLV item/data.
- NetworkDeviceFunction schema Ethernet. The MACAddress property is not
updated to the value in PATCH JSON. This is a regression. The issue is
under investigation.
- PATCH request with request to to change FlowControlConfiguration
property returns success, but do not really apply changes. The issue is
under investigation.
- Fixed an issue where X710DA2 cannot get SFF temperature when another
port is empty.
Release: 29.1 04/11/2024
============================
New OS Support:
- Support RHEL8.9/9.3
E810
-------------
New features:
- Get SFF Info NC-SI OEM Command
- Disable FW LLDP agent in and allow LLDP frames to be sent and received
in the VF.
- Supports Log of MNG packets for debugging purposes.
- Supports PLDM Type 4s for FRU data.
- The E810-CQDA2T adapter now supports 2x2x25 Gbps configuration.
- Supports reduced PTP jitter by improved timestamp accuracy and Port
timer compensation.
- E810-XXVDA4T and E810-CQDA2T now support DPLL updates.
- Supports shorter DPLL lock time
- Force FW LOG to uART even if PF Driver disables
- Option to disable PLDM FRU backup data response when NVM FRU
manufacturing data is not available
Bug fixes:
- IPS: 00788617 - [PA_SI Agile 23-1_USI_SDV_Pass 1_HW_SE450] Qtester
shows "VPD FW check failed (Error)
Description:
1. Power on system and boot into WS2022.
2. Setup Qtester to run 72hrs AC cycle test.
after AC power on, the BMC software calls PLDM_GetFirmwareParameters
and it sometimes (may be once after 300 AC power cycles) returns
Completion Code = 0x01(PLDM Base: Error).
Fix:
Firmware now returns PLDM_ERROR_NOT_READY Completion Code instead of
generic 0x01(PLDM Base: Error) when firmware is not fully ready after
platform reboot.
- When plugging DAC cables into two ports at the same time on Clifton
Channel, it is possible for one port to be unable to establish link.
- To have the metrics data shown on the respective port, map the port to
MAC address before accessing counter registers.
- Resolved an issue where 0x5089 was returned for command
get_sff_temperature when only port1 had optics of E810.
- PLDM T2 NumericSensors didn't send async event when any threshold was crossed.
- NCSI1.2 command Get Transceiver Temperature(0x4A) returned incorrect
temperatures due to wrong endianness.
- Module temp thresholds check running too early causes 0 return, which
is taken as valid and shuts down port.
- GetSensorReading command returns error code 0x1 in case when plug
temperature is higher than 78C (0x4E).
- E810 doesn't support non-contiguous TCs within the LLDP configuration.
It may result in a hang situation if receiving such LLDP packets during
power-on stage. A timeout was added to the firmware polling loop to
trigger a core reset which clears the hang and allows the device to
continue functioning.
- E810 4.3 NVMs use a common map, which introduces a change (new entries)
to an immediate TLV in PFA. FW fails to interpret the new entries in
this specific TLV, which results in adding those new entries again and
again upon every update from the former 4.3 image to 4.3 and above.
Eventually, due to the lack of space in that TLV, any normal attempt to
update will fail.
- NetworkDeviceFunction.Ethernet.PermanentMACaddress should stay with
factory setting if it has been programmed. Read relevant section from
Factory Settings.
- PLDM Type4 showing incorrect default Part Number
- NIC disappeared after NVM signature corruption
- Incorrect log entry format for timestamp value
- Get Link Status command does not return External Device Power Class
value
- Previously, the PLDM Type 5 Command "Activate Firmware" could
potentially cause a subsequent PLDM Type 2 event.
- Resolved an issue where during an ActiveFirmware request coming from
Update Agent (BMC) PLDM Type2, a PlatformEventMessage was generated by
the Firmware Device (Network Adapter). As a result, the response did
not happen, and Update Agent (BMC) treated it as Update Failed.
- Fixed an issue where the UEFI HII interface could not save the setting
of virtualization mode.
- Previously, in PLDM Platform Monitoring and Control, the
sensor_data_size field of SFP thermal sensor PDR was containing wrong
value: unsigned instead of signed char/byte.
- Previously, during ActiveFirmware request coming from Update Agent
(BMC) PLDM Type2 PlatformEventMessage was generated by our Firmware
Device (Network Adapter). As a result, response did not happen and
Update Agent (BMC) treated it as Update Failed.
- Firmware now acquires semaphore before "Load Factory Settings to PFA"
and releases it immediately after.
- Previously, when BMC subscribed to PLDM events, the NIC issued two
equivalent redfish events for the different origins (Network Adapter
and Port) caused by the same trigger (link state change for given
port). This issue caused unnecessary redfish event flood. The
resolution was to change firmware design in order to avoid sending
multiple redfish events for the same trigger.
- Previously, in Network Controller Sideband Interface after
EnableChannel command invoked, the OEM command IANA=0x02A2 GetLldp
occasionally returned LLDP TLVs with missing mandatory values for
chassis_id and port_id.
- Set packageID SDP to correct values for E810-CQDA1.
- Now the patched property of NetworkDeviceFunction.Ethernet.MACAddress
is persistent during reboot. Users can restore to PermanentMACAddress
with ResetSettingsToDefaults.
FVL/SGVL
--------
New features:
- Enable E700 X722 Tx signal to "always on".
- Enable E700 to store events details on the NVM in Recovery Mode.When
entering the Recovery Mode, X710 will store the details of the event in
the NVM.
Bug fixes:
- Resolved an issue where POST to the
NetworkAdapter.ResetSettingsToDefault looked successful from postman,
but after reboot the adapter's Port 1 LLDP setting did not reset to
default.
- Previously, there were cases of Fortville disappearing from the PCIe
bus during reboot stress testing reported on Icelake-based platforms.
These platforms performed a PCIe Hot Reset before asserting PERST# as
part of the warm reboot cycle. PERST# is asserted at approximately the
end of the Hot Reset, but due mostly to the Fortville LCB
implementation, there was a variation in the relative timing of about
65 us, so many edge cases could occur.
- Previously, after configuring "ifconfig ethX down" command on Marvell
devices series 88E1512/88E1514, the peer side (loopback configuration)
was still reporting link up.
- Fixed an issue. Unexpected EMP Reset occurred in a rarely BMC request
combination in a very low probability, which may cause: 'tx_timeout' or
'ARQ: Unknown event 0x0000 ignored' or 'bond down' if bonding is
configured.
- IPS: 00879846 - Intel XXV710-DA2 PCIe 25Gb 2-Port SFP28 Adapter link
speed and status incorrect
Description:
Link event is reported only once at when the machine is powered on,
after that no link event will be generated any more even after the
network cable is inserted and removed, this is incorrect, link event
should be reported when we plugin or remove the AOC cable.
Fix:
Firmware reported link speed value based on advertised capability value
using DNL declaration, changes to read link speed from MAC
- IPS: 00852370 - IEPD Hot Issue: SR645v3 X710 T2L PCIe bandwidth degraded
Description:
X710 PCIe may enter x1 on the AMD Genoa platform in reboot and AC
process.
Customer updated system firmware XCC: KAX318V >> KAX322V UEFI: KAE112O
>> KAE116K Following event occurs intermittently, but high fail rate
PCIe Link Width has degraded from x8 to x1 in physical slot number 3.
Slot 3 is Intel X710-T2L 10GBASE-T 2-Port PCIe Ethernet Adapter,
customer had tried new NIC FW, replace NIC but no help. this system no
re-timer.
Fix:
The firmware changes to enter the PCIE detection phase when PERST
becomes de-asserted
Release: 28.2 08/01/2023
========================
New OS Support:
- Support RHEL8.8/9.2, SLES 15.5
E810
-------------
New features:
- Support NC-SI 1.2 thermal monitoring commands.
Bug fixes:
- IPS: 00833367 - E810-DA2 10/25GbE SFP28 2-Port OCP Ethernet Adapter cannot
enable SRIOV in UEFI
Description:
SRIOV can not be enabled in UEFI
Fix:
Added logic to support on for all PFs
- Resolved an issue were an incorrectly interpreted BDF during MCTP
Endpoint discovery led to sending PLDM events to a non-existing device.
- Resolved an issue where the id field of Event BEJ was changed from the
originating resource Id as the resource number to a deferred binding
resource Id.
- A "Cannot initialize port" failure occurs when running nvmupdate
1.39.32.6 in SLES15SP3, because the tool doesn't support ioctl.
- A SyncE-related transaction between driver and device may cause a PHY
loading failure, during NVM upgrade. Subsequently, PHY errors are
reported to UEFI driver during reboot, resulting in a BIOS hang.
- Resolved an issue where E810-XXV-4T didn't expose one of the On Chip
thermal sensors via PLDM. The sensor was not visible via BMC.
- Resolved an issue where CVL4.1 and CVL4.2 had a problem with Recovery
Clock configuration on port 4, in the case of fully reversed PF<>MAC
mapping. Other configurations were not impacted.
- Resolved an issue where the NC-SI "Reset Channel" (0x05) command was
not reverting the port link state change made by for Real Time
Comprehensive Embedded Management "Network Port Control' (0x34)
command.
- Resolved an issue where, during communication via PLDM Type 6, FW did
not move the operation to the failed state and did not return
INVALID_DATA. Instead, it returned UNSUPPORTED in the case of an
invalid payload.
- Reverted an incorrectly added strict handling of the payload-less action.
- Resolved an issue where the Network Device and Port Metrics are
disabled due to an BMC issue and missing support on BMC side.
- Resolved an issue where in order to change the Forward Error Correction
setting in the UEFI HII the user needs to change the Media detection
setting, save the changes, and then change the FEC setting.
- Previously, promiscuous mode did not see all packets; it only saw those
packets arriving over the wire (that is, not sent from the same
physical function (PF) but a different virtual function (VF).
- Resolved an issue where during the second time of a POST operation,
NetworkAdapter.ResetSettingsToDefault failed with the BMC reporting
"Internal Server Error."
- Resolved an issue when both RMII-based transport (RBT) and Management
Component Transport Protocol (MCTP) were enabled, and PT was enabled on
RBT, then OEM command 0x26 (config LLDP) was being rejected from NC-SI
over MCTP with reason code 0x5081.
- Corrected an issue where updating an NVM image of E810 could result in
a "PHY NVM is not supported in devlink" warning message.
- Previously, E8102CQDA2 adapter showed Linkcap width as x16.
FVL/SGVL
--------
New features:
- Get Link Status AQC response when SFP module is not initialized.
Description:
If the Get Link Status AQC is sent when the SFP module is not
initialized yet, the link can be lost.
When the SFP module is not initialized yet, FW will try again in a
reasonable timeout.
Bug fixes:
- IPS: 00819239 - [Kahauale_BBFV_HCT]X710-T4L NIC adapter can't saved the
"Active Physical Functions" option on uEFI menu.
IPS: 00831264/00844425 - XXV710-DA2 PCIe Adapter NIC port didn't
disable after changed the "Active physical functions"
Description:
Intel XXV710-DA2 PCIe 25Gb 2-Port SFP28 Adapter NIC port didn't disable
after changed the "Active Physical" setting on uEFI menu.
Fix:
Reset the length of the PCIe Alt Autoload section during image
downgrade to a version earlier than FVL9.2
- IPS: 00840914 - [PA_IO Agile-Sprint202310_BDC_Storage_flex]SRIOV
enable/disable both can do SRIOV features
Description:
OS can still create SRIOV VFs when the adapter HII already disables SRIOV
in the BIOS
IPS: 00841528 - [PA_IO Agile-Sprint202310_BDC_Storage_SD530] Intel X722
LOM test SR-IOV function cannot enable VF under ESXi8.0u2 OS
Description:
Open to enter ESXi Host Client-Manage-Hardware-PCI Devices-Select Port
"Intel X722 10GB SFP+" Configure SR-IOV 2.UEFI has set SR-IOV function
3.ESXi8.0u2 Unable to enable VF redhat 9.2 can work well.
Fix:
Correctly set SR-IOV Control Capable bit for Lenovo images,
- IPS: 00839473 - [PA_IO Agile-Sprint202209_BDC_oceancat_Sprint202310]X722
lom WOL fail in SD650.
Description:
WOL function UEIF page show gray, OS can not enable WOL function
Fix:
Enable force link down requests and map channel number in a descending
order. Enable AltRAM implementation then reset corrupted memory block and
recalculate MSI_X VF vectors.
- IPS: 00831248 - XXV710 VPD info question
Description:
lspci -s BUS:Device.Function -vvv command to check VPD info, but it
can't show out the VPD info
Fix:
Enable VPD bit in NVM image
- IPS: 00769725 - [Hakuba] Abnormal cable plug (unplug) event on port 2
and 3 with Intel X710-T4L
Description:
Port2 and port3 of X710-T4L PCIE cannot display event in audit log and
link status/speed in inventory when plug/unplug the cable.
Fix:
There are missing MCTP link status changes as mixed PF no. with port
no. in the MCTP Link Status change handler, and overflowing PLDM queue
with RDE events that were classified as Big Event.
Map Port No. to the corresponding PF and continue, add additional
condition to disable unplanned eventReceiver physical address change.
Disable RDE events in the presence of asynchronous MCTP implementation
without polling for Big Events
Note: it may still occur in loopback mode.
- IPS: 00725539 - Link down on x722 4x10Gb SFP+ PHY card with 27.3 code
level (800039xx)
Description:
After upgrading the FW, all ports are down.
Fix:
Force OCP PnP Autodetection flow after NVM update.
- Resolved an issue where a rare PCI speed degradation with Gen3 to Gen2
was seen during extensive link tests after a reset is caused by a core
reset on an ICX-D platform.
- Resolved an issue where during a write, with http PATCH method
triggered, the LLDP Disable Valid bit was ignored, which resulted in a
skip of write in all scenarios instead of just for the same LLLDP
Enabled value.
- Resolved an issue where if BMC bonding was disabled, NCSI mode was set
to a Manual Switch Mode (depending on the platform), and BMC share port
has changed before doing a power cycle, recovery mode would occur.
Other prerequisites include disabled WOL, disabled LLDP, enabled PXE no
drop, and disabled auto power-on after power loss (in BIOS).
- Fixed an issue where the processing port id was always the same as the
mac address
- Previously, the addition of PCIe re-timers added to the total channel
latency causing replay timer timeout correctable errors.
- Resolved an issue where PLDM type MCTP packets were not accepted due to
missing configuration for PCIe VDM
I350/340/210
------------
New features:
- IPS: 00699338 - Name of I350 interlock in XCC is inconsistent with V1
Description:
Card Name field shall be taken from V1 VPD field instead of "large
resource string". This change applies to 1G Lenovo devices with enabled
AIM support and existing V1 VPD field.
Lenovo Data Center Group Linux OS Support Home Page |
| linux.lenovo.com |
© 2018-2025 Lenovo. All rights reserved |